紧固件名称中英文对照表
紧固件中英文对照(精)
lifting eye nuts
69
DIN601 六角头螺栓
hexagon bolts
ISO4016
70
DIN603
大半圆头方颈螺栓(马车 mushroom head square neck bolts
螺栓)
(carriage bolts)
ISO8677
71
DIN604 沉头带插销马车螺栓
flat countersunk nib bolts
72
DIN605 沉头长方颈马车螺栓
flat countersunk long square neck bolts
73
DIN607 半圆头带插销马车螺栓 cup head nib bolts
74
DIN608 沉头短方颈马车螺栓
flat countersunk short square neck bolts
hexagon nuts
ISO4776 ISO7434 ISO4034
62
DIN557 方螺母-C
square nuts
63
DIN558 六角头螺钉
hexagon screws
ISO4018
64
DIN561
六角头圆柱端紧定螺钉
hexagon set screws with full dog point
GB832-88 GB75-85 GB73-85 GB808-88
31
DIN432 外舌止动垫圈
external tap
GB856-88
32
DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092
33
DIN434 方斜垫圈(U型)
紧固件中英文对照
Description in Chinese 英文品名Desciption in English圆锥销Taper pins圆柱销Parallel pins开槽圆柱头螺钉Slotted cheese head screws开槽盘头螺钉Slotted pan head screws单耳止动垫圈Tab washers开口销Split cooter pins开槽半沉头木螺钉Slotted raised csk head wood screws 开槽半圆头木螺钉Slotted round head wood screws开槽沉头木螺钉Slotted countersunk head wood screws 平垫Plain washers平垫（带倒角）Mediun washers平垫Plain washers重型弹垫Spring lock washers,tang ends标准弹垫Spring lock washers,square ends鞍形弹垫Single coil spring lock washers弹簧止动垫圈Curved spring washers波形弹垫Wave spring washersT型方颈螺栓T-head blots with square neckT型双接头螺栓T-head bolts with double nip螺纹圆锥销Taper pins with threaded endT型头螺栓T-head bolts蝶型螺母（美制）Wing nuts America form蝶型螺母（德制）Wing nuts germany form蝶型螺母（美制）Wing screws America form蝶型螺母（德制）Wing screws germany form圆球型盖型螺母Ball knobs开槽带孔球面圆柱头蚴钉Slotted capstan screws开槽长圆柱端紧定螺钉Slotted set srews with full dog point开槽平端紧定螺钉（半牙）Slotted set srews with chamfered end 小六角特薄细牙螺母Pip nuts with thread外舌止动垫圈External tap小垫圈(用于圆柱头螺钉) Washers for cheese head screws方斜垫圈（U型）Square taper washers forU-section方斜垫圈（I型）Square taper washers forI-sections方垫圈Square washers开槽凹端紧定螺钉Slotted set with cup point六角薄螺母Hexagon thin nuts细牙六角薄螺母Hexagon thin nuts木螺钉专用垫圈Rounds washers for wood constructions密封帽Sealing caps,push-in type活节螺栓B型Eye bolts form B内舌止动垫圈Internal tab washers双耳止动垫圈Washers with two taps滚花高头螺钉Knurled thumb screws with collar开槽滚花高头螺钉Slotted knurled thumb screws with collar 滚花高螺母Knurled thumb nuts with collar滚花薄螺母Knurled thumb thin nuts锁紧垫圈Sealing washers轴用弹性垫圈Retaining rings for shafts(external),circlips孔用弹性垫圈Retaining rings for bores(internal),circlips方头带垫螺栓Square head bolts with collar方头圆柱底端螺栓Square head bolts with half dog point方头带垫关圆底端螺栓Square head bolts with collar,half dog pointT型槽螺母T-slot nuts单头螺柱Single end studs地脚螺栓Masonry bolts带槽圆螺母Slotted round nuts端面带孔圆螺母Round nuts with drilled holes in one face 开槽平端紧定螺钉Slotted set screws with flat point开槽锥端紧定螺钉Slotted set screws with cone point六角螺母Hexagon nuts方螺母-C Square nuts六角头螺钉Hexagon screws六角头圆柱端紧定螺钉Hexagon set screws with full dog point薄型方螺母-B Square nuts without bevel(pressed nuts)六角头木螺钉Hexgon head wood screw(coach screws)吊环螺钉Lifting eye bolts吊环螺母Lifting eye nuts圆锥型槽销Grooved pins,taper grooved圆锥型槽销（半槽）Grooved pins,taper grooved half length平行槽销（带倒角）Grooved pins,parallel grooved full length前端凹槽槽销Grooved pins,reverve grooved half length中部凹槽槽销Grooved pins,center grooved圆头槽销Grooved pins with round head沉头槽销Grooved pins with countersunk head六角螺母棒Turnuckles(center parts),made out of hexagon bar 花蓝螺栓Turnuckles with eye bolt and hook bolt弹性圆柱销Spring pins,heavy type组合式盖型螺母Hexagon domed cap nuts开槽圆螺母(配合沟头扳手) Slotted round nuts for hook spammer圆螺母（带插销孔）Round nuts with set holes盘型弹簧垫圈Disc springs喉箍Hose clamps润滑油嘴（旋扭头）Lubricating nipples,button head管夹Shackles for conduiltsU型螺栓Stirrup bolts(U-bolts)球面垫圈Spherical washers,conical seats圆柱销Parallel pins厚六角螺母Hexagon nuts,1.5d厚六角法兰面螺母Hexagon nuts,1.5d with collar长六角螺母Hexagon nuts,3d外齿锁紧垫圈External teeth lock washers内齿锁紧垫圈Internal teeth lock washers外锯齿锁紧垫圈External teeth serrated lock washers内锯齿锁紧垫圈Internal teeth serrated lock washers开口挡圈Retaining rings for shafts(E-rings),circlips平键（A型）Parallel keys(form A)半圆键Woodruff keys嵌环（支撑环）Thimbles机器螺钉和垫圈组合件Screws and washers assemblies自攻螺钉和垫圈组合件Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉Hexagon cocket head cap screws with hole,low head大六角头螺栓Hexagon head bolts with large head(friction grip nolts)大六角螺母Hexagon nuts with large wideth across flat(friction grip nuts)大垫圈Round washers for friction grip bolts楔型方垫圈Spuare taper washers for friction grip bolts on T-六角法兰面螺母Hexagon flange nuts全金属六角锁紧螺母（2型）Prevailing torque type hexagon nuts,all metallic nuts 轻型弹性圆柱销Spring pins,light type重型弹性圆柱销用垫圈Washers for bolts with heavy type spring pinssISO公制螺纹螺钉（多种头型）Thread forming screws for ISO-metric thread自攻自钻螺钉（多种头型）Self-drilling tapping screws开槽切削螺纹螺钉（多种头型）Thread cutting screws十字槽切削螺纹螺钉（多种头型）Thread cutting screws cross recessT型四爪螺母Tee nuts with pronge钢结构用六角头螺栓连接副Hexagon head fitted bolts for steel structures开槽盘头自攻螺钉Pan head tapping screws with slot开槽沉头自攻螺钉countersunk flat head tapping screws with slot开槽半沉头自攻螺钉Raised sountersunk oval head tapping screws with slot六角头自攻螺钉Hexagon tapping screws圆柱头螺钉用弹簧垫圈Spring lock washers for screws with cylindrical heads十字槽盘头自攻螺攻Pan head tapping screws with cross recessed十字槽沉头自攻螺攻Countersunk flat head tapping screws with cross recessed十字槽半沉头自攻螺攻Raised countersunk oval head tapping screws with cross薄型内六角圆柱头螺钉Hexagon socket head cap screws with,reduced head 十字槽盘头螺钉Pan head screws with cross recessed钢结构用垫圈Washers for steel structures钢结构用六角头螺栓Hexagon head bolts for steel structures内六角沉头螺钉Hexagon socket coutersunk head screws轴用钢丝挡圈Roundwire snap rings for shafts十字槽半沉头木螺钉Cross recessed raised countersunk head wood screws十字槽圆头木螺钉Cross recessed round head wood screws十字槽沉头木螺钉Cross recessed countersunk head wood screws螺纹护套(普通、自锁等) Ciol inserts,coarse,fine thread,silf locking大外径垫圈Washers,outside diameter appro.3d弹簧卡子sping cotter for a bolt平板螺栓Belting bolts(elevator bolts)干壁钉（墙板钉）Dry wall screws环型螺母Lifting nuts(eye nuts)圆螺母用止退垫圈Tab washer for slotted round nuts。
紧固件中英文对照 精华
序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 1DIN1圆锥销taper pins ISO2339GB1172DIN7圆柱销parallel pins ISO2338GB119-86 3DIN84开槽圆柱头螺钉slotted cheese head screws ISO1207GB65-85 4DIN85开槽盘头螺钉slotted pan head screws ISO1580GB67-85 5DIN93单耳止动垫圈tab washers GB8546DIN94开口销split cotter pins ISO1234GB917DIN95开槽半沉头木螺钉slotted raised csk head woodscrewsGB1018DIN96开槽半圆头木螺钉slotted round head wood screws GB999DIN97开槽沉头木螺钉slotted countersunk head woodscrewsGB10010DIN125-A平垫plain washers ISO7089GB97.1-85 11DIN125-B平垫(带倒角）mediun washers ISO7090GB97.2-85 12DIN126平垫plain washers ISO709113DIN127-A重型弹垫spring lock washers,tang ends GB7244 14DIN127-B标准弹垫spring lock washers,square ends GB93-87 15DIN128-A鞍形弹垫single coil spring lock washers GB7245-87 16DIN137-A弹簧止动垫圈curved spring washers17DIN137-B波形弹垫wave spring washers GB955 18DIN186T型方颈螺栓T-head bolts with square neck GB37-88 19DIN188T型双接头螺栓T-head bolts with double nip20DIN258螺纹圆锥销taper pins with threaded end ISO873721DIN261T型头螺栓T-head bolts22DIN315AF蝶型螺母(美制）wing nuts amercia form23DIN315DF蝶型螺母(德制）wing nuts germany form GB62-88 24DIN316AF蝶型螺钉(美制）wing screws amercia form25DIN317DF蝶型螺钉(德制）wing screws germany form德国标准和国际标准、中国标准中英文对照表26DIN319圆球型盖型螺母ball knobs27DIN404开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828DIN417开槽长圆柱端紧定螺钉slotted set srews with full dogpointISO7435GB75-8529DIN427开槽平端紧定螺钉(半牙）slotted set srews withchamfered endISO2342GB73-8530DIN431小六角特薄细牙螺母pipe nuts with thread GB808-88 31DIN432外舌止动垫圈external tap GB856-88 32DIN433小垫圈(用于圆柱头螺钉）washers for cheese head screws ISO7092GB848-9533DIN434方斜垫圈(U型）square taper washers for U-sectionGB852-8834DIN435方斜垫圈(I型）square taper washers for I-sectionsGB852-8835DIN436方垫圈square washers36DIN438开槽凹端紧定螺钉slotted set with cup point ISO7436GB74-85 37DIN439六角薄螺母hexagon thin nuts ISO4035GB6172-86 38DIN439细牙六角薄螺母hexagon thin nuts ISO8675GB6173-8639DIN440木螺钉专用垫圈rounds washers for woodconstructionsISO709440DIN443密封帽sealing caps,push-in type41DIN444活节螺栓B 型eye bolts form B GB798-88 42DIN462内舌止动垫圈internal tab washers43DIN463双耳止动垫圈washers with two taps GB855-8844DIN464滚花高头螺钉knurled thumb screws withcollarGB834-8845DIN465开槽滚花高头螺钉slotted knurled thumb screws with collar46DIN466滚花高螺母knurled thumb nuts with collar GB806-88 47DIN467滚花薄螺母knurled thumb thin nuts GB807-88 48DIN470锁紧垫圈sealing washers49DIN471轴用弹性挡圈retaining rings forshafts(external),circlipsGB894.1-8650DIN472孔用弹性挡圈retaining rings forbores(internal),circlipsGB893.1-8651DIN478方头带垫螺栓square head bolts with collar52DIN479方头圆柱底端螺栓square head bolts with half dog point53DIN480方头带垫半圆底端螺栓square head bolts with collar,half dog point and54DIN508T型槽螺母T-slot nuts ISO29955DIN525单头螺柱single end studs56DIN529地脚螺栓masonry bolts GB799-88 57DIN546带槽圆螺母slotted round nuts GB817-7658DIN547端面带孔圆螺母round nuts with drilled holesin one faceGB815-8859DIN551开槽平端紧定螺钉slotted sit screws with flatpointISO4776GB73-8560DIN553开槽锥端紧定螺钉slotted set screws with conepointISO7434GB71-8561DIN555六角螺母hexagon nuts ISO403462DIN557方螺母-C square nuts GB39-88 63DIN558六角头螺钉hexagon screws ISO401864DIN561六角头圆柱端紧定螺钉hexagon set screws with full dog point65DIN562薄型方螺母-B square nuts without bevel(pressed nuts)66DIN571六角头木螺钉hexagon head wood screws (coachscrews)GB102-8667DIN580吊环螺钉lifting eye bolts ISO3266GB825-76 68DIN582吊环螺母lifting eye nuts69DIN601六角头螺栓hexagon bolts ISO401670DIN603大半圆头方颈螺栓(马车螺栓）mushroom head square neck bolts(carriage bolts)ISO8677GB14-8871DIN604沉头带插销马车螺栓flat countersunk nib bolts72DIN605沉头长方颈马车螺栓flat countersunk long square neck bolts73DIN607半圆头带插销马车螺栓cup head nib bolts74DIN608沉头短方颈马车螺栓flat countersunk short square neck bolts75DIN609六角头精配螺栓（长螺纹）hexagon fitted bolts,longthread76DIN610六角头精配螺栓（短螺纹）hexagon fitted bolts,shortthread77DIN653滚花平头螺钉knurled thumb screws thin type GB835-88 78DIN660半圆头铆钉round head rivets ISO1051GB867-86 79DIN661沉头铆钉contersunk head rivets ISO1051GB869-86 80DIN662半沉头铆钉raised contersunk head rivets ISO105181DIN674大扁头铆钉mushroom head rivets ISO105182DIN703重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83DIN705侧面带孔圆螺母adjusting rings,light range(shafting collars)GB816-8884DIN741卡头wire rope clips85DIN787T型槽螺钉T-slot screws ISO29986DIN835双头螺柱（牙长=2D）studs-metal (end=2d)GB900-8887DIN906内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88DIN908内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89DIN909外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90DIN910外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91DIN911内六角扳手socket wrenches ISO293692DIN912内六角圆柱头螺钉hexagon socket cap screws ISO4762GB70-8593DIN913内六角平端紧定螺钉hexagon socket set screws withflat pointISO4026GB77-8594DIN914内六角尖端紧定螺钉hexagon socket set screws withcone pointISO4027GB78-8595DIN915内六角圆柱端紧定螺钉hexagon socket set screws withdog pointISO4028GB79-8596DIN916内六角凹端紧定螺钉hexagon socket set screws withcup pointISO4029GB80-8597DIN917薄型盲螺母hexagon cap nuts98DIN920开槽小圆柱头螺钉slotted short cheese head screws99DIN921开槽大圆柱头螺钉slotted large cheese headscrewsGB838-88100DIN923开槽圆柱头轴肩螺钉slotted pan head screws withshoulderGB830-88101DIN927开槽无头轴肩螺钉slotted shoulder screws102DIN928焊接方螺母square weld nuts GB/T13680-92 103DIN929焊接六角螺母hexagon weld nuts GB/T13681-92 104DIN931六角头螺栓（半牙）hexagon head screws ISO4014GB5782-86 105DIN933六角头螺栓（全牙）hexagon head screws ISO4017GB5783-86 106DIN934六角头螺母(1型）hexagon full nuts ISO4032GB6170-86 107DIN934细牙六角头螺母(1型）hexagon full nuts ISO8673GB6171-86 108DIN935开槽六角螺母hexagon slotted and castle nuts ISO7035GB6178-86 109DIN936六角头薄螺母hexagon thin nuts ISO4035GB6172.1-86110DIN937六角头开槽薄螺母hexagon thin slotted and castlenutsISO7038GB6181-86111DIN938双头螺距（牙长=1D）studs metal (end=1d)GB897-88 112DIN939双头螺距（牙长=1.25D）studs metal (end=1.25d)GB898-88 113DIN940双头螺距（牙长=1.5D）studs metal (end=1.5d)114DIN960六角头细牙螺栓（半牙）hexagon head bolts,metric finepitch threadISO8765GB5785-86115DIN961六角头细牙螺栓（全牙）hexagon head bolts,metric finepitch threadISO8676GB5786-86116DIN962头部穿孔六角头螺栓additional shapes and versions for bolts117DIN963开槽沉头螺钉slotted countersund head screws ISO 2009GB68-85118DIN964开槽半沉头螺钉slotted raised countersunk ovalhead screwsISO 2010GB69-85119DIN965十字槽沉头螺钉cross recessed countersunk headscrewsISO7046GB819-85120DIN966十字槽半沉头螺钉cross recessed raisedcountersunk head screwsISO7047GB820-85121DIN970六角头螺母hexagon nuts type-1122DIN971六角头螺母hexagon nuts type-2123DIN972细牙六角头螺母(2型）hexagon nuts with fine thread ISO8674GB6176-86 124DIN975牙条(全螺纹）threaded rods(studdings)GB15389-94 125DIN976螺纹销threaded pins(stud bolts)126DIN979六角头开槽薄螺母（２型）hexagon thin slotted and castlenuts127DIN980全金属六角锁紧螺母（１型）prevailling torque type hexagonnuts,all metall nutsISO7199GB6184-86128DIN981圆螺母locknuts ISO2982GB812-88129DIN982六角头尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nylonISO7040GB889.1-86130DIN985六角头薄型尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nylonISO10511GB6172.2-86131DIN986六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132DIN988配合垫片shim rings133DIN1052木材连接用垫片washers for timber connectors 134DIN1151沉头钢钉round plain head nails135DIN1440销钉专用垫片A型plain washers for clevis pins(A型）ISO8738136DIN1441销钉专用垫片plain washers for clevis pins137DIN1444带头销钉clevis pins with head ISO2341138DIN1471圆锥型槽销grooved pins,taper grooved ISO8744GB/T13829.2139DIN1472圆锥型槽销(半槽）grooved pins,taper grooved halflengthISO8745GB/T13829.2140DIN1473平行槽销(带倒角）grooved pins,parallel groovedfull lengthISO8740141DIN1474前端凹槽槽销grooved pins,reserve groovedhalf lengthISO8741142DIN1475中部凹槽槽销grooved pins,centre grooved ISO8742143DIN1476圆头槽销grooved pins with round head ISO8746GB/T13829.3144DIN1477沉头槽销grooved pins with countersunkheadISO8747145DIN1479六角螺母棒turnuckles(centre parts),made out of hexagon bar146DIN1480花篮螺栓turnuckles with eye bolt and hook bolt147DIN1481弹性圆柱销spring pins,heavy type ISO8752GB879-86 148DIN1587组合式盖型螺母hexagon domed cap nuts GB802-88149DIN1804开槽圆螺母（配合沟头扳手）slotted round nuts for hookspanner150DIN1816圆螺母（带插销孔）round nuts with set holes151DIN2093盘型弹簧垫圈disc springs152DIN3017喉箍hose clamps153DIN3404润滑油嘴（旋扭头）lubricating nipples,button head154DIN3567管夹shackles for conduilts155DIN3570U型螺栓stirrup bolts(U-bolts)156DIN6319球面垫圈spherical washers,conical seats GB849-88 157DIN6325圆柱销parallel pins ISO8734158DIN6330厚六角螺母hexagon nuts ,1.5d GB56-88 159DIN6331厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86 160DIN6334长六角螺母hexagon nuts ,3d161DIN6797-A外齿锁紧垫圈external teeth lock washers GB862.1-87 162DIN6797-I内齿锁紧垫圈internal teeth lock washers GB861.1-87163DIN6798-A外锯齿锁紧垫圈external teeth serrated lockwashersGB862.2-87164DIN6798-I内锯齿锁紧垫圈internal teeth serrated lockwashersGB861.2-87165DIN6799 开口挡圈retaining rings for shafts(E-rings),circlipsGB896-76166DIN6885平键（A型）parallel keys(form A )ISO773/2491167DIN6888半圆键woodruff keys ISO3912168DIN6899嵌环（支撑环）thimbles169DIN6900机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170DIN6901自攻螺钉和垫圈组合件tapping screws and washersassembliesGB9074.18-.23171DIN6912薄型带孔内六角圆柱头螺钉hexagon socket head cap screwswith hole,low head172DIN6914大六角头螺栓hexagon head bolts with large head(friction grip bolts)173DIN6915大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174DIN6916大垫圈round washers for friction grip bolts175DIN6917楔型方垫圈spuare taper washers for friction grip bolts on T-176DIN6923六角法兰面螺母hexagon flange nuts ISO4161GB6177-86177DIN6925全金属六角锁紧螺母(2型）prevailing torque type hexagonnuts,all metallic nutsISO7042GB6185.1-2000178DIN7337开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179DIN7338扁平头半空心/全空心铆钉rivets for brake and clutchliningGB875/975-86180DIN7343螺旋夹紧销spiral pins ISO8750 181DIN7346轻型弹性圆柱销spring pins,light type ISO13337182DIN7349重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183DIN7500ISO公制螺纹螺钉(多种头型）threadforming screws for ISO-metric thread184DIN7504自攻自钻螺钉(多种头型）self-drilling tapping screws185DIN7513开槽切削螺纹螺钉(多种头型）thread cutting screws186DIN7516十字槽切削螺纹螺钉(多种头型）thread cutting screws crossrecess187DIN7965T型四爪螺母tee nuts with pronge188DIN7968钢结构用六角头螺栓连接副hexagon head fitted bolts forsteel structuresGB1228/1229/1230189DIN7971开槽盘头自攻螺钉pan head tapping screws withslotISO1481GB5282-85190DIN7972开槽沉头自攻螺钉countersunk flat head tappingscrews with slotISO1482GB5283-85191DIN7973开槽半沉头自攻螺钉raised countersunk oval headtapping screws with slotISO1483GB5284-85192DIN7976六角头自攻螺钉hexagon tapping screws ISO1479GB5285-85193DIN7980圆柱头螺钉用弹簧垫圈spring lock washers for screwswith cylindrical headsISO8738194DIN7981十字槽盘头自攻螺钉pan head tapping screws withcross recessedISO 7049GB845-85195DIN7982十字槽沉头自攻螺钉countersunk flat head tappingscrews with cross recessedISO7050GB846-85196DIN7983十字槽半沉头自攻螺钉raised countersunk oval headtapping screws with crossISO7051GB847-86197DIN7984薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198DIN7985十字槽盘头螺钉pan head screws with crossrecessedISO7045GB818-85199DIN7989钢结构用垫圈washers for steel structures GB1230-84200DIN7990钢结构用六角头螺栓hexagon head bolts for steelstructuresGB1229-84201DIN7991内六角沉头螺钉hexagon socket countersunk headscrewsISO10642202DIN7993轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203DIN7995十字槽半沉头木螺钉cross recessed raisedcountersunk head wood screwsGB952-86204DIN7996十字槽圆头木螺钉cross recessed round head woodscrewsGB950-86205DIN7997十字槽沉头木螺钉cross recessed countersunk headwood screwsGB951-86206DIN8140螺纹护套（普通\自锁等）ciol inserts,coarse,finethread,silf locking207DIN9021大外径垫圈washers,outside diameterappro.3dISO7093GB96.1-85208DIN11024弹簧卡子spring cotter for a bolt209DIN13257平板螺栓belting bolts (elevator bolts)210DIN18182干壁钉（墙板钉）dry wall screws211DIN28129环型螺母lifting nuts(eye nuts)GB63-88212DIN70952圆螺母用止退垫圈tab washers for slotted roundnutsGB858-88尺寸核对OKOKOKOKGB粗din75°GB90°OKDIN对边大１DIN对边大１din槽深din薄GB m1.6～m10 DIN m1~m20din厚内径小DIN薄外径大GB头圆弧小OK。
紧固件中英文对照大全
--------------------------------------------------------------------------------螺栓－－方头螺栓C级UDC 621.882.6 | GB 8-88 | 代替GB8-76Square head bolts-Product grade C－－沉头方颈螺栓UDC 621.882.6 | GB 10-88 | 代替GB10-76Flat countersunk square neck bolts－－沉头带榫螺拴UDC 621.882.6 | GB 11-88 | 代替GB11-76Flat countersunk nib bolts－－半圆头方颈螺栓UDC 621.882.6 | GB 12-88 | 代替GB12-76Cup head square neck bolts－－半圆头带榫螺栓UDC 621.882.6 | GB 13-88 | 代替GB13-76Cup head nid bolts－－大半圆头方颈螺栓C级ISO 8677:1986 | GB 14-1998 | 代替GB14-88Cup head square neck bolts with large head-Product grade C－－大半圆头带榫螺栓UDC 621.882.6 | GB 15-88 | 代替GB15-76Cup head nib bolts with large head－－六角头铰制孔用螺栓UDC 621.882.6 | GB 27-88 | 代替GB27-76Hexagon fit bolts-product grade A and B－－六角头螺杆带孔铰制孔用螺栓UDC 621.882.6 | GB 28-88 | 代替GB28-76Hexagon fit bolts with split pin hole on shank-product grade A and B－－六角头头部带槽螺栓A 和B 级UDC 621.882.6 | GB 29.1-88 | 代替GB29-76 Hexagon bolts with slot on head -product A and B－－十字槽凹穴六角头螺栓UDC 621.882.6 | GB 29.2-88 | 代替GB29-76Cross recessed hexagon bolts with indentation－－六角头螺杆带孔螺栓UDC 621.882.6 | GB 31.1-88 | 代替GB31、23、24-76 Hexagon bolts with split pin hole on shank-product grade A and B－－六角头螺杆带孔螺栓细杆B级UDC 621.882.6 | GB 31.2-88 | 代替GB31、23、24-76 Hexagon bolts with split pin hole on shank-Reduced shank-product grade B－－六角头螺杆带孔螺栓细牙A和B级UDC 621.882.6 | GB 31.3-88 | 代替GB31、23、24-76Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and B－－六角头头部带孔螺栓A 和B级UDC 621.882.6 | GB 32.1-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-product grade A and B－－六角头头部带孔螺栓细杆B级UDC 621.882.6 | GB 32.2-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-Reduced shank-product grade B－－六角头头部带孔螺栓细牙A 和 B 级UDC 621.882.6 | GB 32.3-88 | 代替GB32、25、26-76Hexagon bolts with wire holes on head-Fine pitch thread-product grade A and B－－下方头螺栓B级UDC 621.882.6 | GB 35-88 | 代替GB35-76Square head bolts with small head-praduct grade B－－T 形槽用螺栓UDC 621.882.6 | GB 37-88 | 代替GB37-76Bolts for T-Slot－－加强半圆头方颈螺栓GB /T794-93 | 代替GB794-67Strengthened cup head square neck bolts－－活节螺栓UDC 621.882.6 | GB 798-88 | 代替GB798-76Eye bolts－－地脚螺栓UDC 621.882.6 | GB 799-88 | 代替GB799-76Eyelet bolts－－沉头双榫螺UDC 621.882.6 | GB 800-88 | 代替GB800-77Flat countersunk double nib bolts－－小圆半头低方颈螺栓B级ISO 8678:1988 | GB /T 801-1998 | 代替GB801-88Cup head square neck bolts with small head and short neck-product grade B－－六角头螺栓C级ISO 4016:1999 | GB /T 5780-2000 | 代替GB/T 5780-1986 Hexagon head bolts-product grade C－－六角头螺栓全螺纹C级ISO 4018:1999 | GB /T 5781-2000 | 代替GB/T 5781-1986 Hexagon head bolts-Full thread-product grade C－－六角头螺栓ISO 4014：1999 | GB /T 5782-2000 | 代替GB/T 5782-1986Hexagon head bolts－－六角头螺栓全螺纹ISO 4017：1999 | GB /T 5783-2000 | 代替GB/T 5783-1986 Hexagon head bolts-Full thread－－六角头螺栓-细杆-B级UDC 621.882.6 | GB 5784-86 | 代替GB30、21-76Hexagon head bolts-Reduced shank -Product grade B－－六角头螺栓细牙ISO 8765：1999 | GB /T 5785-2000 | 代替GB/T 5785-1986 Hexagon head bolts with fine pitch thread－－六角头螺栓细牙全螺纹ISO 8676：1999 | GB /T 5786-2000 | 代替GB/T 5786-1986 Hexagon head bolts with fine pitch thread-Full thread－－六角法兰面螺栓-加大系列-B级UDC 621.882.6 | GB 5789-86 |Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓-加大系列-细杆-B级UDC 621.882.6 | GB 5790-86 |Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓小系列ISO 4162：1990 | GB /T 16674-1996 | 代替GB/T 5787、5788-1986Hexagon flange bolts-Small series－－钢网架螺栓球节点用高强度螺栓GB /T 16939-1997 |High strength bolts for joints of space grid structures螺柱－－双头螺柱bm=1d UDC 621.882 | GB 897-88 | 代替GB897-76Double end studs-bm=1d－－双头螺柱bm=1.25d UDC 621.882 | GB 898-88 | 代替GB898-76Double end studs-bm=1.25d－－双头螺柱bm=1.5d UDC 621.882 | GB 899-88 | 代替GB899-76Double end studs-bm=1.5d－－双头螺柱bm=2d UDC 621.882 | GB 900-88 | 代替GB900-76Double end studs--bm=2d－－等长双头螺柱B级UDC 621.882 | GB 901-88 | 代替GB901-76Double end studs(clamping type) -Product grade B－－手工焊用焊接螺柱GB 902.1-89 | 代替GB902-76Weld studs for manual welding－－机动弧焊用焊接螺柱GB 902.2-89 | 代替GB902-76Weld studs for arc welding－－储能焊用焊接螺柱GB 902.3-89 | 代替GB902-76Weld studs for capacitor discharge welding－－等长双头螺柱C级UDC 621.882 | GB 953-88 | 代替GB953-76 Double end studs(clamping type)-product grade C－－螺杆GB /T 15389-94 |Threaded rods螺母－－方螺母C级UDC 621.882.3 | GB 39-88 | 代替GB39-76 Square nuts-product grade C－－六角螺母C级ISO 4034：1999 | GB /T41-2000 | 代替GB/T 41-1986 Hexagon nuts-product grade C－－六角厚螺母ISO 621.882.3 | GB 56-88 | 代替GB56-76Hexagon thick nuts－－蝶形螺母UDC 621.882.3 | GB 62-88 | 代替GB62-76Wing nuts－－环形螺母UDC 621.882.3 | GB 63-88 | 代替GB63-76Lifting nuts－－组合式盖形螺母UDC 621.882.3 | GB 802-88 | 代替GB802-76 Acorn nuts－－球面六角螺母UDC 621.882.3 | GB 804-88 | 代替GB804-76 Hexagon nuts with raised face－－扣紧螺母UDC 621.882.3 | GB 805-88 | 代替GB805-76Tight nuts－－滚花高螺母UDC 621.882.3 | GB 806-88 | 代替GB806-76Knurled nut with collar－－滚花薄螺母UDC 621.882.3 | GB 807-88 | 代替GB807-76Knurled nuts－－小六角特扁细牙螺母UDC 621.882.3 | GB 808-88 | 代替GB808-76 Small hexagon thin nuts-Fine pitch thread－－嵌装圆螺母UDC 621.882.3 | GB 809-88 | 代替GB809-76Lnsert round nuts－－小圆螺母UDC 621.882.3 | GB 810-88 | 代替GB810-76Small round nuts－－圆螺母UDC 621.882.3 | GB 812-88 | 代替GB812-76Round nuts－－端面带孔圆螺母UDC 621.882.3 | GB 815-88 | 代替GB815-76 Round nuts with drilled holes in one face－－侧面带孔圆螺母UDC 621.882.3 | GB 816-88 | 代替GB816-79Round nuts with set pin holes in side－－带槽圆螺母UDC 621.882.3 | GB 817-88 | 代替GB817-76Slotted round nuts－－1型非金属嵌件六角锁紧螺母ISO 7040：1997 | GB /T 889.1-2000 | 代替GB/T 889-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 1－－1型非金属嵌件六角锁紧螺母细牙ISO 10512：1997 | GB /T 889.2-2000 |Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch thread－－盖形螺母UDC 621.882.3 | GB 923-88 | 代替GB923-76Acorn nuts－－1型六角螺母ISO 4032：1999 | GB /T 6170-2000 | 代替GB/T 6170-1986Hexagon nuts,style 1－－1型六角螺母细牙ISO 8673：1999 | GB /T 6171-2000 | 代替GB/T 6171-1986 Hexagon nuts,style 1,with fine pitch thread－－六角薄螺母ISO 4035：1999 | GB /T 6172.1-2000 | 代替GB/T 6172-1986Hexagon thin nuts(chamfered)－－非金属嵌件六角锁紧薄螺母ISO 10511：1997 | GB /T 6072.2-2000 |Prevailing torque type hexagon thin nuts(with non-metallic insert)－－六角薄螺母细牙ISO 8675：1999 | GB /T 6173-2000 | 代替GB/T 6173-1986 Hexagon thin nuts(chamfered) with fine pitch thread－－六角薄螺母无倒角ISO 4036：1999 | GB /T 6174-2000 | 代替GB/T 6174-1986 Hexagon thin nuts(unchamfered)－－2型六角螺母ISO 4033：1999 | GB /T 6175-2000 | 代替GB/T 6175-1986Hexagon nuts,style 2－－2型六角螺母细牙ISO 8674：1999 | GB /T 6176-2000 | 代替GB/T 6176-1986 Hexagon nuts,style 2,with fine pitch thread－－六角法兰面螺母ISO 4161：1999 | GB /T 6177.1-2000 | 代替GB/T 6177-1986 Hexagon nuts with flange－－六角法兰面螺母细牙ISO 10663：1999 | GB /T 6177.2-2000 |Hexagon nuts with flange-fine pitch thread－－1型六角开槽螺母-A和B级UDC 621.882.3 | GB 6178-86 | 代替GB57~58-76 Hexagon slotted and castle nuts,style 1 -product grades A and B－－1型六角开槽螺母-C级UDC 621.882.3 | GB 6179-86 | 代替GB57~58-76Hexagon slotted nuts,style 1 -product grade C－－2型六角开槽螺母-A和B级UDC 621.882.3 | GB 6180-86 |Hexagon slotted and castle nuts,style 2 -Product grades A and B－－六角开槽薄螺母-A和B级UDC 621.882.3 | GB 6181-86 | 代替GB59~60-76 Hexagon thin slotted nuts-Product grades A and B－－2型非金属嵌件六角锁紧螺母ISO 7041：1997 | GB /T 6182-2000 | 代替GB/T 6182-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 2－－非金属嵌件六角法兰面锁紧螺母ISO 7043：1997 | GB /T 6183.1-2000 | 代替GB/T 6183-1986Prevailing torque type hexagon nuts with flange(with non-metallic insert)－－非金属嵌件六角法兰面锁紧螺母细牙ISO 12125：1997 | GB /T 6183.2-2000 | Prevailing torque type hexagon nuts with flange(with non-metallic insert)with fine pitch thread－－1型全金属六角锁紧螺母ISO 7719：1997 | GB /T 6184-2000 | 代替GB/T 6184-1986 Prevailing torque type all-metal hexagon nuts,style 1－－2型全金属六角锁紧螺母ISO 7042：1997 | GB /T 6185.1-2000 | 代替GB/T 6185-1986 Prevailing torque type all-metal hexagon nuts,style 2－－2型全金属六角锁紧螺母细牙ISO 10513：1997 | GB /T 6185.2-2000 |Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch thread－－2型全金属六角锁紧螺母9级ISO 7720：1997 | GB /T 6186-2000 | 代替GB/T 6186-1986Prevailing torque type all-metal hexagon nuts,style 2-Property class 9－－全金属六角法兰面锁紧螺母ISO 7044：1997 | GB /T 6187.1-2000 | 代替GB/T 6187-1986Prevailing torque type all-metal hexagon nuts with flange－－全金属六角法兰面锁紧螺母细牙ISO 12126：1997 | GB /T 6187.2-2000 |Prevailing torque type all-metal hexagon nuts with flange with fine pitch thread－－1型六角开槽螺母细牙A和B级UDC 621.882.3 | GB 9457-88 | 代替GB57、58-76 Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and B－－2型六角开槽螺母细牙A和B级UDC 621.882.3 | GB 9458-88 |Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and B－－六角开槽薄螺母细牙A和B级UDC 621.882.3 | GB 9459-88 | 代替GB59、60-76 Hexagon thin slotted nuts--Fine pitch thread -Product grades A and B－－焊接方螺母GB /T 13680-92 |Square weld nuts－－焊接六角螺母GB /T 13681-92 |Hexagon weld nuts－－平头铆螺母GB /T 17880.1-1999 |Flat head riveted nuts－－沉头铆螺母GB /T 17880.2-1999 |Countersunk head riveted nuts－－小沉头铆螺母GB /T 17880.3-1999 |Small countersunk head riveted nuts－－120°小沉头铆螺母GB /T 17880.4-1999 |120°Small countersunk head riveted nuts－－平头六角铆螺母GB /T 17880.5-1999 |Flat head hexagon riveted nuts－－精密机械用六角螺母ISO 4166：1979 | GB /T 18195-2000 |Hexagon nuts for fine mechanics螺钉－－开槽圆柱头螺钉ISO 1207：1992 | GB /T 65-2000 | 代替GB/T 65-1985 Slotted cheese head screws－－开槽盘头螺钉ISO 1580：1994 | GB /T 67-2000 | 代替GB/T 67-1985Slotted pan head screws－－开槽沉头螺钉ISO 2009：1994 | GB /T 68-2000 | 代替GB/T 68-1985Slotted countersunk flat head screws (common head style)－－开槽半沉头螺钉ISO 2010：1994 | GB /T 69-2000 | 代替GB/T 69-1985 Countersunk slotted raised head screws (common head style)－－内六角圆柱头螺钉ISO 4762：1997 | GB /T 70.1-2000 | 代替GB/T 70-1985 Hexagon socket head cap screws－－内六角平圆头螺钉ISO 7380：1997 | GB /T 70.2-2000 |Hexagon socket button head screws－－内六角沉头螺钉ISO 10642：1997 | GB /T 70.3-2000 |Hexagon socket countersunk head screws－－开槽锥端紧定螺钉UDC 621.882.219 | GB 71-85 | 代替GB71-76Slotted set screws with cone point－－开槽锥端定位螺钉UDC 621.882.2 | GB 72-88 | 代替GB72-76Slotted setscrews with cone point－－开槽平端紧定螺钉UDC 621.882.219.4 | GB 73-85 | 代替GB73-76Slotted set screws with flat point－－开槽凹端紧定螺钉UDC 621.882.219.4.092.6 | GB 74-85 | 代替GB74-76Slotted set screws with cup point－－开槽长圆柱端紧定螺钉UDC 621.882.219.4.092.5 | GB 75-85 | 代替GB75-76Slotted set screws with long dog point－－内六角平端紧定螺钉ISO 4026：1993 | GB /T 77-2000 | 代替GB/T 77-1985 Hexagon socket set screws with flat point－－内六角锥端紧定螺钉ISO 4027：1993 | GB /T 78-2000 | 代替GB/T 78-1985 Hexagon socket set screws with cone point－－内六角圆柱端紧定螺钉ISO 4028：1993 | GB /T 79-2000 | 代替GB/T 79-1985 Hexagon socket set screws with dog point－－内六角凹端紧定螺钉ISO 4029：1993 | GB /T 80-2000 | 代替GB/T 80-1985 Hexagon socket set screws with cup point－－方头长圆柱球面端紧定螺钉UDC 621.882.2 | GB 83-88 | 代替GB83-76Square set screws with long dog point and rounded end－－方头凹端紧定螺钉UDC 621.882.2 | GB 84-88 | 代替GB84-76Square set screws with cup point－－方头长圆柱端紧定螺钉UDC 621.882.2 | GB 85-88 | 代替GB85-76Square set screws with long dog point－－方头短圆柱锥端紧定螺钉UDC 621.882.2 | GB 86-88 | 代替GB86-76Square set screws with short dog point and cone end－－十字槽盘头螺钉ISO 7045：1994 | GB /T 818-2000 | 代替GB/T 818-1985Pan head screws with cross recess－－十字槽沉头螺钉第1部分：钢4.8级ISO 7046-1：1994 | GB /T 819.1-2000 | 代替GB/T 819-1985Countersunk flat head screws (common head style)with cross recess-Part 1:Steel of property class 4.8－－十字槽沉头螺钉第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3ISO 7046-2：1990 | GB /T 819.2-1997 |Cross recessed countersunk flat head screws (common head style)-Grade A-Part 2:Steel of property class 8.8, stainless and non-ferrous metals－－十字槽半沉头螺钉ISO 7047：1994 | GB /T 820-2000 | 代替GB/T 820-1985 Countersunk raised head screws (common head style) with cross recess－－方头平端紧定螺钉UDC 621.882.2 | GB 821-88 | 代替GB821-76Square set screws with chamfered end－－十字槽圆柱头螺钉ISO 7048：1998 | GB /T 822-2000 | 代替GB/T 822-1988Cheese head screws with cross recess－－十字槽小盘头螺钉UDC 621.882.2 | GB 823-88 | 代替GB823-76Cross recessed small pan head screws－－吊环螺钉UDC 621.882 | GB 825-88 | 代替GB825-76Eyebolts－－开槽盘头定位螺钉UDC 621.882.2 | GB 828-88 | 代替GB828-76Slotted pan head set setscrews with dog point－－开槽圆柱端定位螺钉UDC 621.882.2 | GB 829-88 | 代替GB829-76Slotted setscrews with dog point－－开槽圆柱头轴位螺钉UDC 621.882.2 | GB 830-88 | 代替GB830-76Slotted cheese head screws with shoulder－－开槽无头轴位螺钉UDC 621.882.2 | GB 831-88 | 代替GB831-76Slotted shoulder screws－－开槽带孔球面圆柱头螺钉UDC 621.882.2 | GB 832-88 | 代替GB832-76Slotted capstan screws－－开槽大圆柱头螺钉UDC 621.882.2 | GB 833-88 | 代替GB833-76Slotted large cheese head screws－－滚花高头螺钉UDC 621.882.2 | GB 834-88 | 代替GB834-76Knurled thumb screws－－滚花平头螺钉UDC 621.882.2 | GB 835-88 | 代替GB835-76Knurled screws－－滚花小头螺钉UDC 621.882.2 | GB 836-88 | 代替GB836-76Knurled screws with small head－－开槽盘头不脱出螺钉UDC 621.882.2 | GB 837-88 | 代替GB837-76Slotted pan head screws with waisted shank－－六角头不脱出螺钉UDC 621.882.2 | GB 838-88 | 代替GB838-76Hexagon screws with waisted shank－－滚花头不脱出螺钉UDC 621.882.2 | GB 839-88 | 代替GB839-76Knurled thumb screws with waisted shank－－塑料滚花头螺钉UDC 621.882.2 | GB 840-88 | 代替GB840-79Plastic diamond knurlhead screws－－开槽球面圆柱头轴位螺钉UDC 621.882.2 | GB 946-88 | 代替GB946-76Slotted raised head with shoulder－－开槽球面大圆柱头螺钉UDC 621.882.2 | GB 947-88 | 代替GB947-76Slotted large raised cheese head screws－－开槽沉头不脱出螺钉UDC 621.882.2 | GB 948-88 | 代替GB948-76Slotted countersunk head screws with waisted shank－－开槽半沉头不脱出螺钉UDC 621.882.2 | GB 949-88 | 代替GB949-76Slotted raised countersunk head screws with waisted shank－－内六角花形盘头螺钉UDC 621.882.2 | GB 2672-86 | 代替GB2672-81Hexagon lobular socket pan head screws－－内六角花形沉头螺钉UDC 621.882.2 | GB 2673-86 | 代替GB2673-81Hexagon lobular socket countersunk head screws－－内六角花形半沉头螺钉UDC 621.882.2 | GB 2674-86 | 代替GB2674-81Hexagon lobular socket raised countersunk head screws－－内六角圆柱头轴肩螺钉UDC 621.882.215.6 | GB 5281-85 |Hexagon socket head shoulder screws－－内六角花形圆柱头螺钉-4.8级UDC 621.882.2 | GB 6190-86 | 代替GB2671-81 Hexagon lobular socket head cap screws-property class 4.8－－内六角花形圆柱头螺钉-8.8和10.9级UDC 621.882.2 | GB 6191-86 | 代替GB2671-81 Hexagon lobular socket head cap screws-property class 8.8 and 10.9－－精密机械用紧固件十字槽螺钉GB /T 13806.1-92 |Fasteners for mechanics-Cross recessed screws垫圈－－标准型弹簧垫圈UDC 621.882.4 | GB 93-87 | 代替GB93-76Single coil spring lock washers Normal type－－平垫圈C级ISO 7091：2000 | GB /T 95-2002 | 代替GB/T 95-1985Plain washers-Product grade C－－大垫圈A级ISO 7093-1：2000 | GB /T 96.1-2002 | 代替GB/T 96-1985Plain washers-Large series-Product grade A－－大垫圈C级ISO 7093-2：2000 | GB /T 96.2-2002 | 代替GB/T 96-1985Plain washers-Large series-Product grade C－－平垫圈A级ISO 7089：2000 | GB /T 97.1-2002 | 代替GB/T 97.1-1985Plain washers-Product grade A－－平垫圈倒角型A级ISO 7090：2000 | GB /T 97.2-2002 | 代替GB/T 97.2-1985Plain washers,chamfered-Product grade A－－销轴用平垫圈ISO 8738：1986 | GB /T 97.3-2000 |Plain washers for clevis pins－－平垫圈用于螺钉和垫圈组合件ISO 10673：1998 | GB /T 97.4-2002 | 代替GB/T 9074.24、9074.25-1988Plain washers for screw and washer assemblies－－平垫圈用于自攻螺钉和垫圈组合件ISO 10669：1999 | GB /T 97.5-2002 | 代替GB/T 9074.29、9074.30-1988Plain washers for tapping screw and washer assemblies－－小垫圈A级ISO 7092：2000 | GB /T 848-2002 | 代替GB/T 848-1985Plain washers-small series-Product grade A－－球面垫圈UDC 621.882.4 | GB 849-88 | 代替GB849-76Washers with ball face－－锥面垫圈UDC 621.882.4 | GB 850-88 | 代替GB850-76Washers with cone face－－开口垫圈UDC 621.882.4 | GB 851-88 | 代替GB851-76Washers with split－－工字钢用方斜垫圈UDC 621.882.4 | GB 852-88 | 代替GB852-76Square taper washers for I section－－槽钢用方斜垫圈UDC 621.882.4 | GB 853-88 | 代替GB853-76Square taper washers for slot section－－单耳止动垫圈UDC 621.882.4 | GB 854-88 | 代替GB854-76Tab washers with long tab－－双耳止动垫圈UDC 621.882.4 | GB 855-88 | 代替GB855-76Tab washers with long tab and wing－－外舌止动垫圈UDC 621.882.4 | GB 856-88 | 代替GB856-76External tab washers－－圆螺母用止动垫圈UDC 621.882.4 | GB 858-88 | 代替GB858-76Tab washers for round nut－－轻型弹簧垫圈UDC 621.882.4 | GB 859-87 | 代替GB859-76Single coil spring lock washers,Light type－－鞍形弹性垫圈UDC 621.882.4 | GB 860-87 | 代替GB860-76Curved spring washers－－内齿锁紧垫圈UDC 621.882.4 | GB 861.1-87 | 代替GB861-76Lock washers internal teeth－－内锯齿锁紧垫圈UDC 621.882.4 | GB 861.2-87 |Serrated lock washers internal teeth－－外齿锁紧垫圈UDC 621.882.4 | GB 862.1-87 | 代替GB862-76Lock washers external teeth－－外锯齿锁紧垫圈UDC 621.882.4 | GB 862.2-87 |Serrated lock washers external teeth－－波形弹性垫圈UDC 621.882.4 | GB 955-87 | 代替GB955-76Wave spring washers－－锥形锁紧垫圈UDC 621.882.4 | GB 956.1-87 | 代替GB956-76 Countersunk external toothed lock washers－－锥形锯齿锁紧垫圈UDC 621.882.4 | GB 956.2-87 |Countersunk Serrated external toothed lock washers－－特大垫圈C级ISO 7094：2000 | GB /T 5287-2002 | 代替GB/T 5287-1985 Plain washers-Extra large series-Product grade C－－重型弹簧垫圈UDC 621.882.4 | GB 7244-87 |Single coil spring lock washers,heavy type－－鞍形弹簧垫圈UDC 621.882.4 | GB 7245-87 |Curved Single coil spring lock washers－－波形弹簧垫圈UDC 621.882.4 | GB 7246-87 |Wave Single coil spring lock washers木螺钉－－开槽圆头木螺钉UDC 621.882.2 | GB 99-86 | 代替GB99-76Slotted round head wood screws－－开槽沉头木螺钉UDC 621.882.2 | GB 100-86 | 代替GB100-76Slotted countersunk head wood screws－－开槽半沉头木螺钉UDC 621.882.2 | GB 101-86 | 代替GB101-76Slotted raised countersunk head wood screws－－六角头木螺钉UDC 621.882.2 | GB 102-86 | 代替GB102-76Hexagon head wood screws－－十字槽圆头木螺钉UDC 621.882.2 | GB 950-86 | 代替GB950-76Cross recessed round head wood screws－－十字槽沉头木螺钉UDC 621.882.2 | GB 951-86 | 代替GB951-76Cross recessed countersunk head wood screws－－十字槽半沉头木螺钉UDC 621.882.2 | GB 952-86 | 代替GB952-76Cross recessed raised head countersunk head wood screws自攻螺钉－－十字槽盘头自攻螺钉UDC 621.882.216.5.082.8 | GB 845-85 | 代替GB845-76 Cross recessed pan head tapping screws－－十字槽沉头自攻螺钉UDC 621.882.216.5.082.8 | GB 846-85 | 代替GB846-76 Cross recessed countersunk head tapping screws－－十字槽半沉头自攻螺钉UDC 621.882.216.5.082.8 | GB 847-85 | 代替GB847-76 Cross recessed raised countersunk head tapping screws－－开槽盘头自攻螺钉UDC 621.882.215.082.8 | GB 5282-85 |Slotted pan head tapping screws－－开槽沉头自攻螺钉UDC 621.882.215.082.8 | GB 5283-85 |Slotted countersunkhead tapping screws－－开槽半沉头自攻螺钉UDC 621.882.215.082.8 | GB 5284-85 |Slotted raised countersunkhead tapping screws－－六角头自攻螺钉UDC 621.882.215.082.8 | GB 5285-85 |Hexagon head tapping screws－－十字槽盘头自攻锁紧螺钉UDC 621.882 | GB 6560-86 |Cross recessed pan head thread forming screws－－十字槽沉头自攻锁紧螺钉UDC 621.882 | GB 6561-86 |Cross recessed countersunk head thread forming screws－－十字槽半沉头自攻锁紧螺钉UDC 621.882 | GB 6562-86 |Cross recessed raised countersunk head thread forming screws－－六角头自攻锁紧螺钉UDC 621.882 | GB 6563-86 |Hexagon head thread forming screws－－内六角花形圆柱头自攻锁紧螺钉UDC 621.882 | GB 6564-86 |Hexagon lobular socket thread forming screws－－十字槽头凹穴六角头自攻螺钉UDC 621.882.2 | GB 9456-88 |Cross recessed hexagon head tapping screws with indentation－－精密机械用紧固件十字槽自攻螺钉刮削端GB /T 13806.2-92 |Fasteners for fine mechanics-Cross recessed tapping screws-Scrape point－－墙板自攻螺钉GB /T 14210-93 |Dry wall screws－－十字槽盘头自钻自攻螺钉ISO 15481:1999 | GB /T 15856.1-2002 | 代替GB/T 15856.1-1995Cross recessed pan head drilling screws with tapping screw thread－－十字槽沉头自钻自攻螺钉ISO 15482:1999 | GB /T 15856.2-2002 | 代替GB/T 15856.2-1995Cross recessed countersunk head drilling screws with tapping screw thread－－十字槽半沉头自钻自攻螺钉ISO 15483:1999 | GB /T 15856.3-2002 | 代替GB/T 15856.3-1995Cross recessed raised countersunk head drilling screws with tapping screw thread－－六角法兰面自钻自攻螺钉GB /T 15856.4-2002 | 代替GB/T 15856.4-1995Hexagon flange drilling screws with tapping screw thread－－六角凸缘自钻自攻螺钉ISO 15480:1999 | GB /T 15856.5-2002 |Hexagon washer head drilling screws with tapping screw thread－－六角凸缘自攻螺钉ISO 7053:1992 | GB /T 16824.1-1997 |Hexzgon head tapping screws with collar－－六角法兰面自攻螺钉ISO 10509:1992 | GB /T 16824.2-1997 |Hexagon flange head tapping screws销－－开口销ISO 1234:1997 | GB /T 91-2000 | 代替GB/T 91-1986Split pins－－圆锥销ISO 2339:1986 | GB /T 117-2000 | 代替GB/T 117-1996Taper pins－－内螺纹圆锥销ISO 8736:1986 | GB /T 118-2000 | 代替GB?T 118-1996Taper pins with internal thread－－圆柱销不淬硬钢和奥氏体不锈钢ISO 2338:1997 | GB /T 119.1-2000 | 代替GB/T 119-1986Parallel pins,of unhardened steel and austenitic stainless steel－－圆柱销淬硬钢和马氏体不锈钢ISO 8734:1997 | GB /T 119.2-2000 | 代替GB/T 119-1986Parallel pins,of hardened steel and martensitic stainless steel (Dowel pins)－－内螺纹圆柱销不淬硬钢和奥氏体不锈钢ISO 8733:1997 | GB /T 120.1-2000 | 代替GB/T 120-1986Parallel pins with internal thread, of unhardened steel and austenitic stainless steel－－内螺纹圆柱销淬硬钢和马氏体不锈钢ISO 8735:1997 | GB /T 120.2-2000 | 代替GB/T 120-1986Parallel pins with internal thread,of hardened steel and martensitic stainless steel－－开尾圆锥销UDC 621.886 | GB 877-76 | 代替GB877-76Taper pins with split－－螺纹圆柱销UDC 621.886 | GB 878-86 | 代替GB878-76Parallel pins with external thread－－弹性圆柱销直槽重型ISO 8752:1997 | GB /T 879.1-2000 | 代替GB/T 879-1986 Spring-type straight pins-Slotted, heavy duty－－弹性圆柱销直槽轻型ISO 13337:1997 | GB /T 879.2-2000 |Spring-type straight pins-Slotted,light duty－－弹性圆柱销卷制重型ISO 8748:1997 | GB /T 879.3-2000 |Spring-type straight pins-Coiled,heavy duty－－弹性圆柱销卷制标准型ISO 8750:1997 | GB /T 879.4-2000 |Spring-type straight pins-Coiled,standard duty－－弹性圆柱销卷制轻型ISO 8751:1997 | GB /T 879.5-2000 |Spring-type straight pins-Coiled,light duty－－带孔销UDC 621.886 | GB 880-86 | 代替GB880-76Pins with split pin hole－－螺尾锥销ISO 8737:1986 | GB /T 881-2000 | 代替GB/T 881-1986Taper pins with external thread－－销轴UDC 621.886 | GB 882-86 | 代替GB882-76Clevis pins with head－－槽销平行沟槽GB /T 13829.1-92 |Crooved pins-Parallel grooved－－槽销锥销GB /T 13829.2-92 |Crooved pins-taper grooved－－槽销圆头沉头GB /T 13829.3-92 |Grooved pins-with round head or countersunk head铆钉－－平头铆钉UDC 621.884 | GB 109-86 | 代替GB109-76Flat head rivets－－标牌铆钉UDC 621.884 | GB 827-86 | 代替GB827-76Rivets for name plate－－半圆头铆钉(粗制)UDC 621.884 | GB 863.1-86 | 代替GB863-76Round head rivets-Black－－小半圆头铆钉(粗制)UDC 621.884 | GB 863.2-86 |Round head rivets with small head-Black－－平锥头铆钉(粗制)UDC 621.884 | GB 864-86 | 代替GB864-76Cone head rivets-Black－－沉头铆钉(粗制)UDC 621.884 | GB 865-86 | 代替GB865-86Countersunk head rivets-Black－－半沉头铆钉(粗制)UDC 621.884 | GB 866-86 | 代替GB866-76Oval countersunk head rivets-Black－－半圆头铆钉UDC 621.884 | GB 867-86 | 代替GB867-76Round head rivets－－平锥头铆钉UDC 621.884 | GB 868-86 | 代替GB868-76Cone head rivets－－沉头铆钉UDC 621.884 | GB 869-86 | 代替GB869-76 Countersunk head rivets－－半沉头铆钉UDC 621.884 | GB 870-86 | 代替GB870-76Oval countersunk head rivets－－扁圆头铆钉UDC 621.884 | GB 871-86 | 代替GB871-76Flat round head rivets－－扁平头铆钉UDC 621.884 | GB 872-86 | 代替GB872-76Thin head rivets－－扁圆头半空心铆钉UDC 621.884 | GB 873-86 | 代替GB873-76 Oval head semi-tubular rivets－－120°沉头半空心铆钉UDC 621.884 | GB 874-86 | 代替GB874-76 120 degree countersunk head semi-tubular rivets－－扁平头半空心铆钉UDC 621.884 | GB 875-86 | 代替GB875-76 Thin head semi-tubular rivets－－空心铆钉UDC 621.884 | GB 876-86 | 代替GB876-76Tubular rivets－－120°沉头铆钉UDC 621.884 | GB 954-86 | 代替GB954-76120 degree countersunk head rivets－－管状铆钉UDC 621.884 | GB 975-86 | 代替GB975-76Pipe type rivets－－大扁圆头铆钉UDC 621.884 | GB 1011-86 | 代替GB1011-76 Truss head rivets－－120°半沉头铆钉UDC 621.884 | GB 1012-86 | 代替GB1012-76 120 degree oval countersunk rivets－－平锥头半空心铆钉UDC 621.884 | GB 1013-86 | 代替GB1013-76 Cone head semi-tubler rivets－－大扁圆头半空心铆钉UDC 621.884 | GB 1014-86 | 代替GB1014-76 Truss head semi-tublar rivets－－沉头半空心铆钉UDC 621.884 | GB 1015-86 | 代替GB1015-76 Countersunk head semi-tublar rivets－－无头铆钉UDC 621.884 | GB 1016-86 | 代替GB1016-76 Headless rivets－－封闭型扁圆头抽芯铆钉GB 12615-90 |Mushroom head break mandrel closed end blind rivets－－封闭型沉头抽芯铆钉GB 12616-90 |120 deg flush head break mandrel closed end blind rivets－－开口型沉头抽芯铆钉GB 12617-90 |120 deg flush head break mandrel blind rivets－－开口型扁圆头抽芯铆钉GB 12618-90 |Mushroom head break mandrel blind rivets－－扁圆头击芯铆钉GB /T 15855.1-1995 |Flat round head drive rivets－－沉头击芯铆钉GB /T 15855.2-1995 |Countersunk head drive rivets挡圈－－锥销锁紧挡圈UDC 621.885 | GB 883-86 | 代替GB883-76Lock rings with cone pin－－螺钉锁紧挡圈UDC 621.885 | GB 884-86 | 代替GB884-76Lock ring with screw－－带锁圈的螺钉锁紧挡圈UDC 621.885 | GB 885-86 | 代替GB885-76 Lock rings with screw and circlip－－轴肩挡圈UDC 621.885 | GB 886-86 | 代替GB886-76Rings for shoulder－－螺钉紧固轴端挡圈UDC 621.885 | GB 891-86 | 代替GB891-76Lock rings at the end of shaft with screw－－螺栓紧固轴端挡圈UDC 621.885 | GB 892-86 | 代替GB892-76Lock rings at the end of shaft with bolt－－孔用弹性挡圈-A型UDC 621.885 | GB 893.1-86 | 代替GB893-76 Circlips for holes-type A－－孔用弹性挡圈-B型UDC 621.885 | GB 893.2-86 |Circlips for hole-type B－－轴用弹性挡圈-A型UDC 621.885 | GB 894.1-86 | 代替GB894-76 Circlips for shaft-type A－－轴用弹性挡圈-B型UDC 621.885 | GB 894.2-86 |Circlips for shaft-type B－－孔用钢丝挡圈UDC 621.885 | GB 895.1-86 | 代替GB895-76 Roundwire snap rings for hole－－轴用钢丝挡圈UDC 621.885 | GB 895.2-86 | 代替GB895-76 Roundwire snap rings for shaft－－开口挡圈UDC 621.885 | GB 896-86 | 代替GB896-76“E”rings－－钢丝锁圈UDC 621.885 | GB 921-86 | 代替GB921-76Round wire circlips－－夹紧挡圈UDC 621.885 | GB 960-86 | 代替GB960-76Grip rings紧固件-组合件和连接副－－钢结构用高强度大六角头螺栓GB /T 1228-91 | 代替GB1228-84 High strength bolts with large hexagon head for steel structures－－钢结构用高强度大六角头螺母GB /T 1229-91 | 代替GB1229-84High strength large hexagon nuts for steel structures－－钢结构用高强度垫圈GB /T 1230-91 | 代替GB1230-84High strength plain washers for steel structures－－钢结构用扭剪型高强度螺栓连接副GB /T 3632-1995 | 代替GB3632-83Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures－－螺栓或螺钉和平垫圈组合件ISO 10644：1998 | GB /T 9074.1-2002 | 代替GB/T 9074.1、9074.14-1988Bolt or screw and washer assemblies with plain washers－－十字槽头螺钉和外锯齿锁紧垫圈组合件UDC 621.882 | GB 9074.2-88 |Cross recessed pan head screw and serrated lock washer external teeth assemblies－－十字槽盘头螺钉和弹簧垫圈组合件UDC 621.882 | GB 9074.3-88 |Cross recessed pan head screw and single coll spring lock washer assemblies－－十字槽盘头螺钉、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.4-88 |Cross recessed pan head screw, single coil spring lock washer assemblies－－十字槽小盘头螺钉和平垫圈组合件UDC 621.882 | GB 9074.5-88 |Cross recessed small pan head screw and small plain washer assemblies－－十字槽小盘头螺钉和大垫圈组合件UDC 621.882 | GB 9074.6-88 |Cross recessed small pan head screw and big plain washer assemblies－－十字槽小盘头螺钉和弹簧垫圈组合件UDC 621.882 | GB 9074.7-88 |Cross recessed small pan head screw and single coil spring lock washer assemblies－－十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.8-88 |Cross recessed small pan head screw, single coil spring lock washer and plain washer assemblies －－十字槽沉头螺钉和锥形锁紧垫圈组合件UDC 621.882 | GB 9074.9-88 |Cross recessed countersunk head screw and countersunk serrated external toothed lock washer assemblies－－十字槽半沉头螺钉和锥形锁紧垫圈组合件UDC 621.882 | GB 9074.10-88 |Cross recessed raised countersunk head screw and countersunk external toothed lock washer assemblies－－十字槽凹穴六角头螺栓和平垫圈组合件UDC 621.882 | GB 9074.11-88 |Cross recessed hexagon bolt with indentation and plain washer assemblies－－十字槽凹穴六角头螺栓和弹簧垫圈组合件UDC 621.882 | GB 9074.12-88 |Cross recessed hexagon bolt with indetation single coil spring lock washer assemblies－－十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.13-88 | Cross recessed hexagon bolt with indetation,single coil lock washer and plain washer assemblies －－六角头螺栓和弹簧垫圈组合件UDC 621.882 | GB 9074.15-88 |Hexagon head bolt and single coil spring lock washer assemblies－－六角头螺栓和外锯齿锁紧垫圈组合件UDC 621.882 | GB 9074.16-88 |Hexagon head bolt and serrated lock washer external teeth assemblies－－六角头螺栓、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.17-88 |Hexagon head bolt,single coil spring lock washer and plain washer assemblies－－自攻螺钉和平垫圈组合件ISO 10510：1999 | GB /T 9074.18-2002 | 代替GB/T 9074.18、9074.19、9074、22、9074、23-1988Tapping screw and washer assemblies with plain washers－－十字槽凹穴六角头自攻螺钉和平垫圈组合件UDC 621.882 | GB 9074.20-88 |Cross recessed hexagon head tapping screw with indentation and plain washer assemblies－－十字槽凹穴六角头自攻螺钉和大垫圈组合件UDC 621.882 | GB 9074.21-88 |Cross recessed hexagon head tapping sorew with indentation and large plain washer assemblies。
紧固件DIN ISO GB标准中英文对照表
紧固件DIN ISO GB标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in EnglishISO-Standard GB-Standard1 DIN1 圆锥销 taper pins ISO2339 GB1172 DIN7 圆柱销 parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉 slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉 slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈 tab washers GB8546 DIN94 开口销 split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉 slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉 slotted round head wood screws GB999 DIN97 开槽沉头木螺钉 slotted countersunk head wood screws GB10010 DIN125-A 平垫 plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫 plain washers ISO709113 DIN127-A 重型弹垫 spring lock washers,tang ends GB724414 DIN127-B 标准弹垫 spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫 single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈 curved spring washers17 DIN137-B 波形弹垫 wave spring washers GB95518 DIN186 T型方颈螺栓 T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓 T-head bolts with double nip20 DIN258 螺纹圆锥销 taper pins with threaded end ISO873721 DIN261 T型头螺栓 T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母 ball knobs27 DIN404 开槽带孔球面圆柱头螺钉 slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉 slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母 pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈 external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈 square washers36 DIN438 开槽凹端紧定螺钉 slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母 hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母 hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈 rounds washers for wood constructions ISO709440 DIN443 密封帽 sealing caps,push-in type41 DIN444 活节螺栓B 型 eye bolts form B GB798-8842 DIN462 内舌止动垫圈 internal tab washers43 DIN463 双耳止动垫圈 washers with two taps GB855-8844 DIN464 滚花高头螺钉 knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉 slotted knurled thumb screws with collar46 DIN466 滚花高螺母 knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母 knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈 sealing washers49 DIN471 轴用弹性挡圈 retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈 retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓 square head bolts with collar52 DIN479 方头圆柱底端螺栓 square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓 square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母 T-slot nuts ISO29955 DIN525 单头螺柱 single end studs56 DIN529 地脚螺栓 masonry bolts GB799-8857 DIN546 带槽圆螺母 slotted round nuts GB817-7658 DIN547 端面带孔圆螺母 round nuts with drilled holes in one faceGB815-8859 DIN551 开槽平端紧定螺钉 slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉 slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母 hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉 hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉 hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉 hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉 lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母 lifting eye nuts69 DIN601 六角头螺栓 hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓 flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓 flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓 cup head nib bolts74 DIN608 沉头短方颈马车螺栓 flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹） hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹） hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉 knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉 round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉 contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉 raised contersunk head rivets ISO105181 DIN674 大扁头铆钉 mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母 adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母 adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头 wire rope clips85 DIN787 T型槽螺钉 T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D） studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉 hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉 hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉 hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉 hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手 socket wrenches ISO293692 DIN912 内六角圆柱头螺钉 hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉 hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉 hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉 hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉 hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母 hexagon cap nuts98 DIN920 开槽小圆柱头螺钉 slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉 slotted large cheese head screws GB838-88 100 DIN923 开槽圆柱头轴肩螺钉 slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉 slotted shoulder screws102 DIN928 焊接方螺母 square weld nuts GB/T13680-92103 DIN929 焊接六角螺母 hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙） hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙） hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86 108 DIN935 开槽六角螺母 hexagon slotted and castle nuts ISO7035GB6178-86109 DIN936 六角头薄螺母 hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母 hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D） studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D） studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D） studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙） hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙） hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓 additional shapes and versions for bolts 117 DIN963 开槽沉头螺钉 slotted countersund head screws ISO 2009 GB68-85 118 DIN964 开槽半沉头螺钉 slotted raised countersunk oval head screws ISO 2010 GB69-85119 DIN965 十字槽沉头螺钉 cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉 cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母 hexagon nuts type-1122 DIN971 六角头螺母 hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销 threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型） hexagon thin slotted and castle nuts 127 DIN980 全金属六角锁紧螺母（1型） prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母 locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母 prevailling torque type hexagonnuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母 prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母 prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片 shim rings133 DIN1052 木材连接用垫片 washers for timber connectors134 DIN1151 沉头钢钉 round plain head nails135 DIN1440 销钉专用垫片A型 plain washers for clevis pins(A型) ISO8738 136 DIN1441 销钉专用垫片 plain washers for clevis pins137 DIN1444 带头销钉 clevis pins with head ISO2341138 DIN1471 圆锥型槽销 grooved pins,taper grooved ISO8744 GB/T13829.2 139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full lengthISO8740141 DIN1474 前端凹槽槽销 grooved pins,reserve grooved half lengthISO8741142 DIN1475 中部凹槽槽销 grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销 grooved pins with round head ISO8746 GB/T13829.3 144 DIN1477 沉头槽销 grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒 turnuckles(centre parts),made out of hexagon bar 146 DIN1480 花篮螺栓 turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销 spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母 hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手） slotted round nuts for hook spanner 150 DIN1816 圆螺母（带插销孔） round nuts with set holes151 DIN2093 盘型弹簧垫圈 disc springs152 DIN3017 喉箍 hose clamps153 DIN3404 润滑油嘴（旋扭头） lubricating nipples,button head154 DIN3567 管夹 shackles for conduilts155 DIN3570 U型螺栓 stirrup bolts(U-bolts)156 DIN6319 球面垫圈 spherical washers,conical seats GB849-88157 DIN6325 圆柱销 parallel pins ISO8734158 DIN6330 厚六角螺母 hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母 hexagon nuts ,1.5d with collar GB6177-86 160 DIN6334 长六角螺母 hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈 external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈 internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈 external teeth serrated lock washersGB862.2-87164 DIN6798-I 内锯齿锁紧垫圈 internal teeth serrated lock washersGB861.2-87165 DIN6799 开口挡圈 retaining rings for shafts(E-rings),circlipsGB896-76166 DIN6885 平键（A型） parallel keys(form A ) ISO773/2491167 DIN6888 半圆键 woodruff keys ISO3912168 DIN6899 嵌环（支撑环） thimbles169 DIN6900 机器螺钉和垫圈组合件 screws and washers assembliesGB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件 tapping screws and washers assemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉 hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓 hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母 hexagon nuts with large wideth acrossflat(friction grip nuts)174 DIN6916 大垫圈 round washers for friction grip bolts175 DIN6917 楔型方垫圈 spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母 hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型） prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头） blind rivets GB12617/12618 179 DIN7338 扁平头半空心/全空心铆钉 rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销 spiral pins ISO8750181 DIN7346 轻型弹性圆柱销 spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈 washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws forISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母 tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副 hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉 pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉 countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉 raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉 hexagon tapping screws ISO1479 GB5285-85 193 DIN7980 圆柱头螺钉用弹簧垫圈 spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉 pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉 countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉 raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉 hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉 pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈 washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓 hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉 hexagon socket countersunk head screwsISO10642202 DIN7993 轴用钢丝挡圈 roundwire snap rings for shafts GB895.2-86 203 DIN7995 十字槽半沉头木螺钉 cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉 cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉 cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等） ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈 washers,outside diameter appro.3d ISO7093GB96-85208 DIN11024 弹簧卡子 spring cotter for a bolt209 DIN13257 平板螺栓 belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉） dry wall screws211 DIN28129 环型螺母 lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈 tab washers for slotted round nuts GB858-渗碳和渗氮常识钢的渗碳---就是将低碳钢在富碳的介质中加热到高温(一般为900--950C),使活性碳原子渗入钢的表面,以获得高碳的渗层组织。
最全紧固件中英文对照资料
最全緊固件中英文對照，外貿必備詞典！一、緊固件 Fasteners標準緊固件 Standard Fasteners非標準緊固件 Nonstandard Fasteners特殊緊固件 Special Fasteners汽車緊固件 Automotive Fasteners銅制緊固件 Brass Fasteners航天用緊固件 Aerospace Fasteners精密緊固件 Precision Fasteners化學緊固件 Chemical Fasteners摩托車緊固件 Motorcycle Fasteners不銹鋼緊固件 Stainless Steel Fasteners鐵道緊固件 Railway Fasteners防松緊固件 Self-locking Fasteners高強度緊固件 High strength FastenersPEM緊固件 PEM Fasteners鋼結構緊固件 Steel Structural Fasteners壓鉚緊固件 Self-Clinching Fasteners鋁制緊固件 Aluminum Fasteners鈦合金緊固件 Titanium Alloy Fasteners尼龍緊固件 Nylon Fasteners精制緊固件 Finished Fastener粗制緊固件 Unfinished Fastener螺紋緊固件 Threaded Fastener半精制緊固件 Semi-Finished Fastener抗剪緊固件 Shear Fastener抗拉緊固件 Tension Fastener面板緊固件 Panel Fasteners二、螺栓 Bolts六角頭螺栓Hexagon Head Bolts六角法蘭面螺栓Hexagon Flange Bolts軌道螺栓（魚尾螺絲）Track Bolts高強度螺栓 High Strength Bolts地腳螺栓Eyelet Bolts馬車螺栓 Carriage Bolts護攔螺栓 Guardrail Bots焊接螺栓 Weld Bolts雙頭螺栓 Double End Bolts鋼結構連接副 Structural Bolting內六角螺栓 Hex Socket Bolts合金鋼螺栓 Alloy Steel Bolts方頭螺栓 Square Head Bolts/Square Bolts鉤頭螺栓 Hook Bolts不銹鋼螺栓 Stainless steel Bolts異型螺栓 Special Bolts吊環螺栓 Lifting Eye Bolts汽車螺栓 Automotive Bolts法蘭螺栓 Flange Bolts輪胎螺栓 Wheel BoltsT型螺栓 T Bolts扁頭螺栓 Pan Head Bolts蝶形螺栓 Wing Bolts沉頭螺栓 Countersunk Bolts沉頭方頸螺栓 Countersunk Square Neck Bolts帶榫螺栓 Cup head Nib Bolts沉頭雙榫螺栓 Flat Countersunk Double Nib Bolts活節螺栓 Eye Bolts壓鉚螺栓 Clinching Bolts紅打螺栓 Hot Forging Bolts圓頭螺栓 Round Head Bolts圓頭方頸螺栓 Round Head Square Neck Bolts圓頭雙榫螺栓 Round Head Fin Neck Bolts米制圓頭方頸螺栓 Metric Round Head Square Neck BoltsT型帶孔螺栓 T bolts withHole六角頭鉸制孔用螺栓 Hexagon Fit Bolts六角頭螺桿帶孔螺栓 Hexagon Bolts with split pin hole on shank鋼網架螺栓球節點用高強度螺栓 High Strength Bolts for joints ofspace grid structures 基礎螺栓 Foundation BoltsU型螺栓 U Bolts高張力螺栓 High Strength Bolts大尺寸螺栓 Big Size Bolts螺椿栓 Stud Bolts拉栓 Blind Bolts重型六角頭螺栓 Heavy Hex Bolts大頭馬車螺栓 Step Bolts扭矩控制螺栓 T.C. Bolts蛋形頸軌道用螺栓 Elliptic Neck Track Bolts調節螺栓，調節螺釘 Pitch-Adjustable Bolts and Screws加長非標雙頭螺栓 Lengthen Non-Standard Stud Bolts電梯膨脹螺栓 Elevator Expansion Bolts三、螺釘 Screws六角螺釘Hex Head Cap Screws/Hex Screws六角機械螺釘 Hex Head Machine Bolts六角法蘭螺釘 Hex Flange Screws內六角孔螺絲 Hex Socket Cap Screws內六角沉頭螺釘 Hex Socket Flat Countersunk Head Cap Screws緊定螺釘/固定螺釘 Set Screws止付螺釘Socket Set Screws方頭緊定螺釘 Square Head Slotted Head Set Screws翼形螺釘/蝶形螺釘 Wing Screws精密螺釘 Precision Screws自攻螺釘 Self-Tapping Screws自削螺釘 Thread Cutting Screws鉆尾螺釘 Self-Drilling Screws旋入螺釘 Drive Screws機械螺釘 Machine Screws木螺釘 Wood Screws家具螺釘 Furniture Screws纖維板釘/塑板螺釘 Chipboard Screws墻用螺釘 Drywall Screws剪力釘(焊接螺釘) Welding Studs螺絲附華司組合 Screws And Washers Assembled (Sems)銅螺釘 Brass Screws鋁螺釘 Aluminum Screws合金鋼螺釘 Alloy Steel Screws組合螺釘 SEM screws電子螺釘 Electronic Screws微小精密螺釘 Micro Screws塑料螺釘 Plastic Screws復合材料用螺釘 Particle Board Screws鈦合金螺釘 Titanium Alloy Bolts鈦、鋯、鉬、鈮等螺絲、零件、材料 Ti ,Zr ,Mo, Nb Pare Metal Bolts Parts 拇指螺絲 Thumb Screws飛機特殊扣件 Source Control Bolts電梯螺釘 Elevator Screws四角頭固定螺釘 Square Set Screws單向螺釘 One Way Lag Screws管夾螺釘 Hose Clamp Screws不銹鋼固定螺釘 Stainless Steel Hex Socket Cap Screws不銹鋼內六角螺釘 Stainless Steel Hex Socket Cap Screws鉸鏈螺釘 Hinge Screws貨柜螺釘 Container Screws復合材料鉆尾螺釘 Bi-Metal Self Drilling Screws三角牙螺釘 Tri-lobular Thread Screws高低牙螺釘 High Low Screws夾板用螺釘 Particle Board Screws馬桶螺釘 Toilet Closet Bolts特長螺釘 Special Longer Screws建業螺釘 Building Fasteners不銹鋼六角螺絲 Stainless Steel Hex Socket Cap Screws不銹鋼特殊螺釘 Special Stainless Steel Screws寬牙螺釘（粗牙螺釘） Coarse Thread Screws鏈帶螺釘 Collated Screws水泥螺釘 Concrete Screws板模螺釘 Construction Bolts鋅蝶螺釘 Die Cast Wing Screws; Zinc Alloy重型車釘 Heavy Duty Wheel Hub Bolts內六角固定螺釘 Hex Socket Set Screws復合材料用螺釘（夾板用） Particle Board Screws犁壁螺釘 Plow Bolts不銹鋼木螺絲 Stainless Steel Wood Screws套掛螺栓及螺釘 Toggle Bolts鈦合金膨脹螺釘 Titanium Alloy Expansion Bolts不銹鋼高低牙螺釘 Stainless Steel High-Low Thread Screws不銹鋼機械螺釘 Stainless Steel Machine Screws不銹鋼鉆尾螺釘 Stainless Steel Self Drilling Screws不銹鋼自攻螺釘 Stainless Steel Self Tapping Screws不銹鋼自削螺釘 Stainless Steel Thread Cutting Screws不銹鋼三角牙螺釘 Stainless Steel Tri-Lobular Thread Screws 不銹鋼寬牙螺釘 Stainless Steel Coarse Thread Screws開槽沉頭螺釘 Slotted Flat Countersunk Head Machine Screws 開槽盤頭螺釘 Slotted Pan Head Machine Screws十字槽盤頭螺釘 Cross Recessed Pan Head Machine Screws 滾花頭臺階螺釘 Knurled Thurmb Screws六角頭木螺釘 Hexagon Head Wood Screws平頭滾花螺釘 Knurled Thin Thumb Screws四、螺母/螺帽 Nuts六角螺母 Hexagon Nuts六角蓋形螺母 Hex Cap Nuts六角鋸齒螺母 Hex Serrated Nuts六角法蘭螺母 Hex Flange Nuts六角平面螺母 Hex Flat Nuts六角厚螺母Hex Thick Nuts重型六角開槽螺母 Heavy Hexagon Slotted Nuts高腳螺母 Hex Coupling Nuts (High Nuts)圓螺母 Round Nuts四角螺母/四方螺母 Square Nuts四方焊接螺母 Square Weld Nuts四爪螺母Four-Claw Nuts管用螺母 Pipe Nuts輪殼螺母 Wheel Nuts蝶型螺母 Wing NutsU形螺母 U NutsT形螺母 T Nuts環首螺母 Eye Nuts齒形螺母 Kep Nuts齒花螺母 Clinch Nuts焊接螺帽 Weld Nuts壓鉚螺母 Self-clinching Nuts高張力螺母 High Strength Nuts建業用螺母 Structural Nuts不銹鋼螺母 Stainless Steel Nuts銅螺母 Brass Nuts鋁螺母 Aluminum Nuts合金鋼螺母 Alloy Steel Nuts重型車螺母 Heavy Duty Wheel Hub Nuts鐵器焊接袋帽 Acorn Cap Nuts金屬預置扭矩式螺母 All-Metal Prevailing Torque Type Nuts壁虎螺母 Anchor Nuts大尺寸螺母 Big Size Nuts鐵蓋袋帽 Closed End Acorn Nuts盤形華司螺母 Conical Washer Nuts鐵蓋+尼龍圈組合蓋帽 Din 986 Domed Cap Nuts法蘭尼龍蓋帽 Flange Nylon Insert Lock Nuts平面華司螺母 Flat Washer Nuts六角割溝螺母 Hex Slotted Nuts自鎖螺母 Self-Locking Nuts制止螺母 Sliding NutsSLN-自動防松螺母 SLN Self-Locking Nuts特殊螺母 Special Nuts彈簧螺母 Spring Nuts不銹鋼法蘭螺母 Stainless Steel Flange Nuts不銹鋼六角輪緣尼龍螺母 Stainless Steel Flange Nylon Insert Lock Nuts 不銹鋼六角重型螺母 Stainless Steel Heavy Hex Nuts不銹鋼六角螺母 Stainless Steel Hex Nuts不銹鋼尼龍嵌入螺母 Stainless Steel Nylon Insert Lock Nuts普通六角螺母 Hex Nuts六角重型螺母 Heavy Hex Nuts薄型螺母 Hex Jam Nuts尼龍嵌入防松螺母 Nylon Insert Lock Nuts尼龍鎖緊螺母Nylon Cage Nuts機械螺絲用六角螺母 Hex Machine Screw Nuts米制六角開槽螺母 Metric Slotted Hex Nuts軌道螺栓用方螺母 Track Bolt Nuts米制六角金屬鎖緊螺母 Prevalling Torque Hexagon Nuts開槽螺母Slotted Round Nuts六角開槽薄螺母Hexagon Slotted Thin Nuts五、螺柱 Studs壓鉚螺柱 Self-Clinching Studs銅螺柱 Brass Studs焊接螺柱 Weld Studs雙頭螺柱 Double End Studs六角螺柱 Hex Studs支撐卡柱 Self-Clinching Standoffs六、墊圈 Washers彈簧墊圈 Spring Washers/Spring Lock Washers寬型彈簧墊圈 Extra-duty Helical Spring Lock Washers杯型墊圈 Cup washers波形墊圈 Wave Washers內齒墊圈 Internal Tooth Washers外齒墊圈 External Tooth Washers銅墊圈 Copper Washers方墊圈 Square Washers密封墊圈 Sealing Washers碟形彈簧墊圈 Disc Spring Washers外舌止動墊圈External Tab Washers高強度墊圈 High strengthen washers橡膠墊圈 Rubber Washers鎖緊墊圈 Lock Washers平墊圈 Plain Washers鞍型彈性墊圈 Curved Spring Washers鋸齒鎖緊彈性墊圈 Toothed lock washers外鋸齒鎖緊墊圈 Serrated Lock Washers錐形墊圈 Taper Washers重型彈簧墊圈 Heavy Spring Lock Washers尼龍墊圈 Nylon Washers淬硬鋼墊圈 Hardened Steel Washers七、鉚釘 Rivets平頭鉚釘 Flat Head Rivets擊芯鉚釘 Drive Rivets彩色鉚釘 Colored Rivets沉頭鉚釘 Countersunk Head Rivets半沉頭鉚釘 Oval Countersunk Head Rivets平錐頭鉚釘 Cone Head Rivets抽芯鉚釘 Blind Rivets開口鉚釘 Split Rivets開口型抽芯鉚釘 Open End Blind Rivets拉鉚釘 Pop Rivets封閉鉚釘Closed End Rivets封閉性抽芯鉚釘 Sealed Type Blind Rivets塑料鉚釘 Plastic Rivets空心鉚釘 Tubular Rivets環槽鉚釘 Ring Groove Rivets單鼓型鉚釘 Single-Grip Rivets圓頭鉚釘 Round Head Rivets高沉頭鉚釘 Countersunk Head Rivets鋁鉚釘 Aluminum Rivets實心鉚釘 Solid Rivets沉頭實心鉚釘 Countersunk Head Solid Rivets燈籠鉚釘 Lantern Blind Rivets半空心鉚釘 Semi-Tubular Rivets圓頭半空心鉚釘 Semi-tubular Pan Head Rivets異型鉚釘 Special Rivets不銹鋼鉚釘 Stainless Steel Rivets雙鼓型鉚釘 Multi-grip Rivets高強度鉚釘 High Strength Rivets臺階鉚釘 Step Rivets面板鉚釘 Tablet Rivets開花型抽芯鉚釘 Flowering Blind Rivets拉花型抽芯鉚釘 Peel Type Blind Rivets溝槽型抽芯鉚釘 Grooved Type Blind Rivet鉚接工具 Riveting Tool八、壁虎（膨脹螺栓）Anchors/Expansion Bolts化學錨栓 Chemical Anchors打入式壁虎 Hammer Drive Anchors內迫壁虎 Drop in Anchors重型壁虎 Heavy Duty Anchors錘釘壁虎 Hit Anchors中空壁虎 Hollow Wall Anchors套管壁虎 Sleeve Anchors插片壁虎 Ceiling Anchors門窗、地板專用壁虎 Nylon Frame Anchors or Metal frame Anchors電梯壁虎 Bolt Anchors車修壁虎 Wedge Anchors魚眼壁虎 Tie Wire Anchors外迫壁虎 Cut Anchors塑料膨脹 Plastic Anchors不銹鋼重載脹栓 Heavy Duty Expansion Anchors象腳壁虎 Elephant Foot Anchors長型蘭花夾 Short Strap Anchors九、銷 Pins開口銷 Split Pins圓錐銷 Taper Pins鎖銷 Lock Pins銷軸 Clevis Pins with head槽銷 Grooved Pins彈性銷 Spring Pins圓柱銷 Parallel Pins彈性圓柱銷 Slotted Spring Pins帶孔銷 Pins with split pin hole十、擋圈 Circlips/Rings開口擋圈 E rings孔用擋圈 Circlips for holes軸用鋼絲擋圈 Roundwire Snap Rings for shaft軸肩擋圈Rings for shoulder夾緊擋圈 Grip Rings軸用卡簧 Circlips for shafts帶齒軸用擋圈 Retaining Rings with Lugs for shafts鋼絲鎖圈 Round wire Circlips錐形鎖緊擋圈 Lock Rings with cone pins十一、其他 Others牙條 Threaded Rod沖壓件 Stampings平鍵 Parallel Keys半圓鍵 Woodruff Keys扳手 Spanners鋼絲螺套 Wire Thread Insert自動車床車削件 CNC Turning Parts齒輪 Gears模具 Molds線材盤元 Iron or steel wire rod鉸鏈 Hinge表面處理 Surface Treatment。
紧固件-中英文对照
紧固件-中英文对照No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出) A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut 六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt 车辆(汽车)螺丝、螺帽Automotive Fasteners 航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws 链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy 重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws 套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed CapNuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod 线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire 不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives 成型冲模Header Punches In Various Drives 螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass) 螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉SpheroidizingBright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator 滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet MetalFasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains 机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-LowThread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。
紧固件-中英文对照
No.xx简写中文1 screw scr螺丝2 nut nut螺母3 washer wash垫圈4 head hd头5 thread thre螺纹6 coating coat镀层7 rivet riv铆钉8 standoff stdoff内外六角钉9 driver driv穴10 hexagon hexa六角11 tooth tooth齿12 lock lck锁13 spring spr弹簧14 wave wave波浪型15 pitch pitch牙距16 partial thread PT半螺纹17 PT PT一种螺纹形式18 Full Thread FT全螺纹19 silver silv银20 cone cone锥形21 Eco-syn Eco 30度牙的一种螺纹22 ThreadForming TF自攻螺纹23 Self Tapping self tapp自切屑螺纹24 pin pin销25 shaft Shaf轴26 steel St铁27 stainless steel SS不锈钢28 Brass(Cu) Bras(Cu)铜29 Aluminum AL铝30 Rubber Rub橡胶31 machine screw mech scr机制螺丝32 SEM screw SEM Scr组合螺丝33 Material material材料34 Grade GD等级35 Finish Finish表面处理36 Point Point点37 Clamp Clam夹子38 internal Int内39 external ext外40 thickness /厚度41 length /xx42 hole /xx43 Metric Metcric公制44 DIN /德标45 ANSI /美标46 JIS /日标螺丝相关参数英语对照A: Machine Screw:机械螺丝B: Tapping Screw:自攻螺丝(分使用于金属与使用于塑料二种) B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. (塑料用,自攻螺丝)C: Wooden Screw :木工螺丝D: Drywall Screw :水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass:xxe. Bronze:青铜f. UNS C11000 Copper:锑铜Finish Code:外观处理规格Head Code:头部外型螺丝型号Drive Code:头部剖沟,特征型号Length Code:螺丝长度(mm)A-1: Thread Code:螺丝型号A-2: Length Code:螺丝长度:A-3: Drive Code/头部剖沟,特征.a. Slotted:一字( Minus )b. Phillips:十字( Plus )c. Phil-Slot:一字/十字d. Hex Scoket:xxe. One Way:单向(只可锁入,不可退出)A-4: Head Code/头部外型.a. Flat:平头(锁入后,顶部与工作件齐平)b. Oval:色拉头c. Round:圆头d. Pan:圆扁头e. Truss:大圆扁头f. Hex :六角头A-5: Finish Code/外观处理.a. Z: Zine-Plated:镀锌b. Ni: Ni-Plated:镀镍c. Tin-Plated:镀锡d. Zine Plated / Green Iridite:镀锌绿膜处理.e. Radiant Plated:镀五彩f. Passivate:抗氧化处理.g. Alodial Finish:无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement镀后去氢，防止氢脆Case carburization表面渗碳With across flats对边With across corners对角Radius of fillet:头下圆角Transition thread length过度螺纹Wrenching height扳拧高度Rockwell铬氏硬度Vickers维氏硬度Brinellxx氏硬度Metallography microscope金相显微镜Salt spray device盐雾试验箱Tensile testing machine拉力试验机Cold forming冷打Hot forging红镦P C 8 = property class 8机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawingxx：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter直径Lengthxx各类紧固件标准件产品xx对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力xx壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts) 圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角xx螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws 固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control BoltsxxBlind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine 气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater 空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine 止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace 球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod 马达轴承轴心组件Bearing Shaft(Motor) 轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind NutsxxBlind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds 其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动xx钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle 针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws 不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。
紧固件标准件中英文对照
英文名称对应标准Square head bolts GB/T 8-88 C 级Flat countersunk square neck bolts GB/T 10-88 沉头沉带榫螺栓Flate countersunk nib bolts GB/T 11-88 (大)半圆头方颈螺栓Cup head square neck (with large head)bolt GB/T 14/15-88六角头铰制孔用螺栓Hexagon fit boltsGB/T 27-88 A 和B 级六角头螺杆带铰制孔用螺栓(细杆)Hexagon fit bolts with split pin hole on shank(Reduced shank) GB/T 28-88 A 和B 级十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation GB/T 29.2-88 A 和B 级六角头头部带孔螺栓Hexagon bolts with wire holes on head GB/T 32.1-88 A 和B 级T 型槽用螺栓Bolt for T-slot GB/T 35.1-88 B 级加强半圆头方颈螺栓Strengthened cap head square neck bolts GB/T 794.1-93 活节螺栓Eye bolts GB/T798-88地角螺栓Eyelet bolts GB/T799-88头角头螺栓Hexagon head bolts GB/T5780-2000 C 级六角头法兰面螺栓Hexagon flange bolts GB/T5789-86 B 级外六角花法兰面螺栓Steel hexalobular head bolt with small flangeDIN 34801-9918.久美特Geomet 19.耐落Nylok 陆锈宝Rupst 20.翡丽雅特 ViridAct 21.美加力Magni 沉头方劲螺栓中文名称一.孔别三.常用名称1.螺丝类方头螺栓1.割沟Slotted2.十字穴 Phillips3.米字穴 Pozidriv(cross recess)4.十字割沟 Slotted phillips5.四角孔Square6.十字方孔 Square phillips7.六角孔hexagon8.方孔割沟Square slotted9.梅花穴Six-lobe 10.三角孔Triangle 11.Y 型槽Y-type 12.斜Y 槽Tri-wing 13.五等角5-Point 二,电镀1.电镀锌Zinc plated2.白皮Plain finished3.五彩Yellow zinc plated4.镀镍Nickel plated5.热浸锌Hot dip galvanized6.黑锌Black zinc plated7.镀黑Black finished8.染黑Black oxide9.(黑)磷酸盐(black)Phosphated 10.黄铜 Brass 11.镀青蓝Unichrome plated 12.古铜A.C Brontze 13.青古铜Antique brass 14.机械镀锌Mechanical galvanized 15.绿锌Green zinc plated 16.电锌腊Zinc plated&waxed 17.达克锈Dacrotizing plated英文名称对应标准双头螺柱bm=1d Double end studs-bm=1d GB/T 897-88等长双头螺柱 B 级Double end studs(clamping type)-product grade A GB/T 901-88螺杆Thread rods GB/T 15389-943.螺钉类英文名称对应标准开槽圆柱头螺钉Slotted cheese head screws GB/T65-2000开槽沉头螺钉Slotted countersunk flat head screws (common head style) GB/T68-2000 eqv ISO 2009-94开槽半沉头螺钉Countersunk slotted raised head screws(common head style)GB/T69-2000 eqv ISO 2010-94内六角圆柱头螺钉Hexagon socket head cap screws GB/T70.1-2000 eqv ISO 4762.2-97内六角平圆头螺钉Hexagon socket button head screws GB/T70.2-2000 eqv ISO 7380-97内六角沉头螺钉Hexagon socket countersunk head screws GB/T70.3-2000 eqv ISO 10642-97十字槽盘头螺钉Pan head screw with cross recess GB/T818-2000 eqv ISO 7045-94十字槽半沉头螺钉Countersunk raised head screws(common head style)with cross recess GB/T820-2000 eqv ISO 7047-94十字槽圆柱头螺钉Cheese head screws with cross recess GB/T822-2000 eqv ISO 7048-94滚花高头螺钉Knurled thumb screws GB 834-88滚花平头螺钉Knurled screws GB 835-88内六角花形盘头螺钉Hexagon lobular socket pan head scerws GB 2672-86内六角圆柱头轴肩螺钉Hexagon socket head shoulder scerws GB/T 5281-854.自攻螺钉 英文名称对应标准十字槽盘头盘自攻螺钉Cross recessed pan head tapping screws GB 845-85十字槽沉头盘自攻螺钉Cross recessed countersunk head tapping screws GB 846-85十字槽盘头盘自攻锁紧螺钉Cross recessed pan head thread forming screws GB 6560-86十字槽凹穴六角头自攻螺钉Cross recessed hexagon head tapping screws with indentationGB 9456-98十字槽自攻螺钉-刮削端(用于精密机械)cross recessed tapping screws-scrape point(fasters for fine mechanics)GB/T 13806-2墙板自攻螺钉Dry wall screws GB/T14210-93十字槽盘头自钻自攻螺钉Cross recessed pan head self-drilling tapping screws GB/T15856.1-95六角凸缘自攻螺钉Hexagon head tapping screws with collarGB/T16824.1-97 eqv ISO 7053-92中文名称中文名称中文名称英文名称对应标准方螺母-C 级Square nuts-product grade C GB/T39-88六角螺母-C 级Hexagon nuts-product grade C GB/T41-2000eqv ISO 4034-99六角厚螺母Hexagon thick nuts GB/T56-88六角薄螺母Hexagon thin nuts GB/T6172.1-2000eqvISO 4035-99蝶形螺母Wing nuts GB/T 62-88组合式盖形螺母Acorn nutsGB/T 802-88球面六角螺母Hexagon nut with raised face GB/T 804-88滚花高螺母kunrled nut with collarGB/T 806-881型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert).style 1GB/T889.1-2000eqv 7040-97盖形螺母Acorn nutsGB/T 923-88六角薄螺母 无倒角Hexagon thin nuts (unchamfered)GB/T6174-2000eqvISO 4036-99六 角法兰面螺母Hexagon nuts with flangeGB/T6177.1-2000eqv ISO 4161-991型六角开槽螺母Hexagon slotted and castle nuts.style1GB/T 6178-86全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts GB/T 6184-2000eqv ISO 7719-97焊接方螺母square weld nut GB/T 13680-92焊接六角螺母Hexagon weld nuts GB/T 13681-92平头铆螺母Flat head riveted nuts GB/T 17880.1-996.挡圈 英文名称对应标准锥销锁紧挡圈Lock ring with corne pin GB/T 883-86轴肩挡圈Rings for shouderGB/T 891-86螺钉紧固轴端挡圈Lock rings at the end of shaft with screw GB/T 893.1-86孔用弹性挡圈-A 型Circlips for holes -typeA GB/T 894.1-86轴用弹性挡圈Circlips for shaft -typeA GB/T 895-2-86开口挡圈"E"ringsGB/T 896-86钢丝锁圈Round coire circlips GB/T 921-86夹紧挡圈Crip ringsGB/T 960-86中文名称中文名称英文名称对应标准弹簧垫圈(标准型)Single coil spring lock washers (normal type)GB/T 93-87平垫圈-C 级Plain washersGB/T 95-85eqv ISO 7091-2000大平垫圈Plain washers-large series GB/T 96-85 A 和B 级鞍形弹性垫圈Curved spring washers GB/T 860-87内齿锁紧垫圈Lock washers internal teethGB/T 861.1-87内锯齿锁紧垫圈Serrated lock washers internal teeth GB/T 861.2-87外锯齿锁紧垫圈Serrated lock washers external teeth GB/T 862.2-87波型弹性垫圈Wave spring washersGB/T 955-87锥形锁紧垫圈Countersunk external toothed look washersGB/T 956.1-87锥形锯齿锁紧垫圈Countersunk serrated external toothed lock washers GB/T 956.2-878.销英文名称对应标准开口销Split pins GB/T 91-2000eqvISO1234-97圆锥销Taper pinsGB/T 117-2000eqvISO2339-86螺纹圆柱销Paraller pins with external thread GB/T 878-86销轴Clevis pins with head GB/T 882-86平头铆钉Flat head rivetsGB/T 109-86平锥头铆钉（粗制）Cone-head rivets-black GB/T 864-86空心铆钉Tubular rivetsGB/T 876-86封闭型扁圆头抽芯铆钉Mushroom head break mandred closed end blind rivets GB/T 12615-90开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivetsGB/T 12617-90中文名称中文名称9.紧固件-组合件和连接副英文名称对应标准中文名称钢结构用高强度大六角头螺栓High strength bolts with large hexagon head for steel structures GB/T1230-91钢结构用高强度大六角头螺母High strength large hexagon nuts for steel stuctures GB/T1229-91钢结构用高强度大六角头垫圈High strength plain washers for steel structures GB/T1230-91钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures GB/T3632-95十字槽盘头螺钉,弹簧垫圈和平垫圈组合件Cross recessed pan head screw ,single coil spring lock washer and plain washer assemblies GB/T 9074-.4-88无头焊钉Headless for stud welding GB/T 10432-89圆柱头焊钉Cheese head studs for stud welding GB/T 10433-89机械焊接螺钉Weld screws with metric thread DIN 34817-2001。
紧固件中英文对照大全
紧固件中英文对照大全-------------------------------------------------------------------------------- 螺栓－－方头螺栓 C级 UDC 621.882.6 | GB 8-88 | 代替 GB8-76 Square head bolts-Product grade C－－沉头方颈螺栓 UDC 621.882.6 | GB 10-88 | 代替 GB10-76 Flat countersunk square neck bolts－－沉头带榫螺拴 UDC 621.882.6 | GB 11-88 | 代替 GB11-76 Flat countersunk nib bolts－－半圆头方颈螺栓 UDC 621.882.6 | GB 12-88 | 代替 GB12-76 Cup head square neck bolts－－半圆头带榫螺栓 UDC 621.882.6 | GB 13-88 | 代替 GB13-76 Cup head nid bolts－－大半圆头方颈螺栓 C级 ISO 8677:1986 | GB 14-1998 | 代替 GB14-88 Cup head square neck bolts with large head-Product grade C－－大半圆头带榫螺栓 UDC 621.882.6 | GB 15-88 | 代替 GB15-76 Cup head nib bolts with large head－－六角头铰制孔用螺栓 UDC 621.882.6 | GB 27-88 | 代替 GB27-76 Hexagon fit bolts-product grade A and B－－六角头螺杆带孔铰制孔用螺栓 UDC 621.882.6 | GB 28-88 | 代替 GB28-76 Hexagon fit bolts with split pin hole on shank-product grade A and B－－六角头头部带槽螺栓 A 和 B 级 UDC 621.882.6 | GB 29.1-88 | 代替 GB29-76 Hexagon bolts with slot on head -product A and B－－十字槽凹穴六角头螺栓 UDC 621.882.6 | GB 29.2-88 | 代替 GB29-76 Cross recessed hexagon bolts with indentation－－六角头螺杆带孔螺栓 UDC 621.882.6 | GB 31.1-88 | 代替 GB31、23、24-76 Hexagon bolts with split pin hole on shank-product grade A and B－－六角头螺杆带孔螺栓细杆 B级 UDC 621.882.6 | GB 31.2-88 | 代替 GB31、23、24-76 Hexagon bolts with split pin hole on shank-Reduced shank-product grade B－－六角头螺杆带孔螺栓细牙 A和B级 UDC 621.882.6 | GB 31.3-88 | 代替 GB31、23、24-76Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and B －－六角头头部带孔螺栓 A 和 B级 UDC 621.882.6 | GB 32.1-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-product grade A and B－－六角头头部带孔螺栓细杆 B级 UDC 621.882.6 | GB 32.2-88 | 代替 GB32、25、26-76 Hexagon bolts with wire holes on head-Reduced shank-product grade B－－六角头头部带孔螺栓细牙 A 和 B 级 UDC 621.882.6 | GB 32.3-88 | 代替GB32、25、26-76Hexagon bolts with wire holes on head-Fine pitch thread-product grade Aand B －－下方头螺栓 B级 UDC 621.882.6 | GB 35-88 | 代替 GB35-76 Square head bolts with small head-praduct grade B－－T 形槽用螺栓 UDC 621.882.6 | GB 37-88 | 代替 GB37-76 Bolts for T-Slot－－加强半圆头方颈螺栓 GB /T794-93 | 代替 GB794-671Strengthened cup head square neck bolts－－活节螺栓 UDC 621.882.6 | GB 798-88 | 代替 GB798-76 Eye bolts－－地脚螺栓 UDC 621.882.6 | GB 799-88 | 代替 GB799-76 Eyelet bolts－－沉头双榫螺 UDC 621.882.6 | GB 800-88 | 代替 GB800-77 Flat countersunk double nib bolts－－小圆半头低方颈螺栓 B级 ISO 8678:1988 | GB /T 801-1998 | 代替 GB801-88 Cup head square neck bolts with small head and short neck-product grade B－－六角头螺栓 C级 ISO 4016:1999 | GB /T 5780-2000 | 代替 GB/T 5780-1986 Hexagon head bolts-product grade C－－六角头螺栓全螺纹 C级 ISO 4018:1999 | GB /T 5781-2000 | 代替 GB/T5781-1986 Hexagon head bolts-Full thread-product grade C－－六角头螺栓 ISO 4014：1999 | GB /T 5782-2000 | 代替 GB/T 5782-1986 Hexagon head bolts－－六角头螺栓全螺纹 ISO 4017：1999 | GB /T 5783-2000 | 代替 GB/T 5783-1986 Hexagon head bolts-Full thread－－六角头螺栓-细杆-B级 UDC 621.882.6 | GB 5784-86 | 代替 GB30、21-76 Hexagon head bolts-Reduced shank -Product grade B－－六角头螺栓细牙 ISO 8765：1999 | GB /T 5785-2000 | 代替 GB/T 5785-1986 Hexagon head bolts with fine pitch thread－－六角头螺栓细牙全螺纹 ISO 8676：1999 | GB /T 5786-2000 | 代替 GB/T 5786-1986 Hexagon head bolts with fine pitch thread-Full thread－－六角法兰面螺栓-加大系列-B级 UDC 621.882.6 | GB 5789-86 | Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓-加大系列-细杆-B级 UDC 621.882.6 | GB 5790-86 | Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓小系列 ISO 4162：1990 | GB /T 16674-1996 | 代替 GB/T 5787、5788-1986Hexagon flange bolts-Small series－－钢网架螺栓球节点用高强度螺栓 GB /T 16939-1997 | High strength bolts for joints of space grid structures 螺柱－－双头螺柱 bm=1d UDC 621.882 | GB 897-88 | 代替 GB897-76 Double end studs-bm=1d－－双头螺柱 bm=1.25d UDC 621.882 | GB 898-88 | 代替 GB898-76 Double end studs-bm=1.25d－－双头螺柱 bm=1.5d UDC 621.882 | GB 899-88 | 代替 GB899-76 Double end studs-bm=1.5d－－双头螺柱 bm=2d UDC 621.882 | GB 900-88 | 代替 GB900-76 Double end studs--bm=2d－－等长双头螺柱 B级 UDC 621.882 | GB 901-88 | 代替 GB901-762Double end studs(clamping type) -Product grade B－－手工焊用焊接螺柱 GB 902.1-89 | 代替 GB902-76 Weld studs for manualwelding－－机动弧焊用焊接螺柱 GB 902.2-89 | 代替 GB902-76 Weld studs for arcwelding－－储能焊用焊接螺柱 GB 902.3-89 | 代替 GB902-76 Weld studs for capacitor discharge welding－－等长双头螺柱 C级 UDC 621.882 | GB 953-88 | 代替 GB953-76 Double endstuds(clamping type)-product grade C －－螺杆 GB /T 15389-94 | Threaded rods 螺母－－方螺母 C级 UDC 621.882.3 | GB 39-88 | 代替 GB39-76 Square nuts-product grade C－－六角螺母 C级 ISO 4034：1999 | GB /T41-2000 | 代替 GB/T 41-1986 Hexagon nuts-product grade C－－六角厚螺母 ISO 621.882.3 | GB 56-88 | 代替 GB56-76 Hexagon thick nuts－－蝶形螺母 UDC 621.882.3 | GB 62-88 | 代替 GB62-76 Wing nuts－－环形螺母 UDC 621.882.3 | GB 63-88 | 代替 GB63-76 Lifting nuts－－组合式盖形螺母 UDC 621.882.3 | GB 802-88 | 代替 GB802-76 Acorn nuts－－球面六角螺母 UDC 621.882.3 | GB 804-88 | 代替 GB804-76 Hexagon nutswith raised face－－扣紧螺母 UDC 621.882.3 | GB 805-88 | 代替 GB805-76 Tight nuts－－滚花高螺母 UDC 621.882.3 | GB 806-88 | 代替 GB806-76 Knurled nut with collar－－滚花薄螺母 UDC 621.882.3 | GB 807-88 | 代替 GB807-76 Knurled nuts－－小六角特扁细牙螺母 UDC 621.882.3 | GB 808-88 | 代替 GB808-76 Small hexagon thin nuts-Fine pitch thread－－嵌装圆螺母 UDC 621.882.3 | GB 809-88 | 代替 GB809-76 Lnsert round nuts－－小圆螺母 UDC 621.882.3 | GB 810-88 | 代替 GB810-76 Small round nuts－－圆螺母 UDC 621.882.3 | GB 812-88 | 代替 GB812-76 Round nuts－－端面带孔圆螺母 UDC 621.882.3 | GB 815-88 | 代替 GB815-76 Round nuts with drilled holes in one face3－－侧面带孔圆螺母 UDC 621.882.3 | GB 816-88 | 代替 GB816-79 Round nuts with set pin holes in side－－带槽圆螺母 UDC 621.882.3 | GB 817-88 | 代替 GB817-76 Slotted round nuts－－1型非金属嵌件六角锁紧螺母 ISO 7040：1997 | GB /T 889.1-2000 | 代替GB/T 889-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 1－－1型非金属嵌件六角锁紧螺母细牙 ISO 10512：1997 | GB /T 889.2-2000 |Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch thread －－盖形螺母 UDC 621.882.3 | GB 923-88 | 代替 GB923-76 Acorn nuts－－1型六角螺母 ISO 4032：1999 | GB /T 6170-2000 | 代替 GB/T 6170-1986 Hexagon nuts,style 1－－1型六角螺母细牙 ISO 8673：1999 | GB /T 6171-2000 | 代替 GB/T 6171-1986 Hexagon nuts,style 1,with fine pitch thread－－六角薄螺母 ISO 4035：1999 | GB /T 6172.1-2000 | 代替 GB/T 6172-1986 Hexagon thin nuts(chamfered)－－非金属嵌件六角锁紧薄螺母 ISO 10511：1997 | GB /T 6072.2-2000 | Prevailing torque type hexagon thin nuts(with non-metallic insert)－－六角薄螺母细牙 ISO 8675：1999 | GB /T 6173-2000 | 代替 GB/T 6173-1986 Hexagon thin nuts(chamfered) with fine pitch thread－－六角薄螺母无倒角 ISO 4036：1999 | GB /T 6174-2000 | 代替 GB/T 6174-1986 Hexagon thin nuts(unchamfered)－－2型六角螺母 ISO 4033：1999 | GB /T 6175-2000 | 代替 GB/T 6175-1986 Hexagon nuts,style 2－－2型六角螺母细牙 ISO 8674：1999 | GB /T 6176-2000 | 代替 GB/T 6176-1986 Hexagon nuts,style 2,with fine pitch thread－－六角法兰面螺母 ISO 4161：1999 | GB /T 6177.1-2000 | 代替 GB/T 6177-1986 Hexagon nuts with flange－－六角法兰面螺母细牙 ISO 10663：1999 | GB /T 6177.2-2000 | Hexagonnuts with flange-fine pitch thread－－1型六角开槽螺母-A和B级 UDC 621.882.3 | GB 6178-86 | 代替 GB57~58-76 Hexagon slotted and castle nuts,style 1 -product grades A and B－－1型六角开槽螺母-C级 UDC 621.882.3 | GB 6179-86 | 代替 GB57~58-76 Hexagon slotted nuts,style 1 -product grade C－－2型六角开槽螺母-A和B级 UDC 621.882.3 | GB 6180-86 | Hexagon slotted and castle nuts,style 2 -Product grades A and B－－六角开槽薄螺母-A和B级 UDC 621.882.3 | GB 6181-86 | 代替 GB59~60-76 Hexagon thin slotted nuts-Product grades A and B－－2型非金属嵌件六角锁紧螺母 ISO 7041：1997 | GB /T 6182-2000 | 代替 GB/T 6182-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 2－－非金属嵌件六角法兰面锁紧螺母 ISO 7043：1997 | GB /T 6183.1-2000 | 代替GB/T 6183-19864Prevailing torque type hexagon nuts with flange(with non-metallic insert)－－非金属嵌件六角法兰面锁紧螺母细牙 ISO 12125：1997 | GB /T 6183.2-2000 |Prevailing torque type hexagon nuts with flange(with non-metallicinsert)with fine pitch thread －－1型全金属六角锁紧螺母 ISO 7719：1997 | GB /T 6184-2000 | 代替 GB/T 6184-1986 Prevailing torque type all-metal hexagon nuts,style 1－－2型全金属六角锁紧螺母 ISO 7042：1997 | GB /T 6185.1-2000 | 代替 GB/T 6185-1986 Prevailing torque type all-metal hexagon nuts,style 2－－2型全金属六角锁紧螺母细牙 ISO 10513：1997 | GB /T 6185.2-2000 | Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch thread－－2型全金属六角锁紧螺母 9级 ISO 7720：1997 | GB /T 6186-2000 | 代替GB/T 6186-1986Prevailing torque type all-metal hexagon nuts,style 2-Property class 9－－全金属六角法兰面锁紧螺母 ISO 7044：1997 | GB /T 6187.1-2000 | 代替GB/T 6187-1986Prevailing torque type all-metal hexagon nuts with flange－－全金属六角法兰面锁紧螺母细牙 ISO 12126：1997 | GB /T 6187.2-2000 | Prevailing torque type all-metal hexagon nuts with flange with fine pitch thread－－1型六角开槽螺母细牙 A和B级 UDC 621.882.3 | GB 9457-88 | 代替 GB57、58-76 Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and B －－2型六角开槽螺母细牙 A和B级 UDC 621.882.3 | GB 9458-88 |Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and B－－六角开槽薄螺母细牙 A和B级 UDC 621.882.3 | GB 9459-88 | 代替 GB59、60-76 Hexagon thin slotted nuts--Fine pitch thread -Product grades A and B －－焊接方螺母 GB /T 13680-92 | Square weld nuts－－焊接六角螺母 GB /T 13681-92 | Hexagon weld nuts－－平头铆螺母 GB /T 17880.1-1999 | Flat head riveted nuts－－沉头铆螺母 GB /T 17880.2-1999 | Countersunk head riveted nuts－－小沉头铆螺母 GB /T 17880.3-1999 | Small countersunk head riveted nuts－－120°小沉头铆螺母 GB /T 17880.4-1999 | 120°Small countersunk head riveted nuts－－平头六角铆螺母 GB /T 17880.5-1999 | Flat head hexagon riveted nuts－－精密机械用六角螺母 ISO 4166：1979 | GB /T 18195-2000 | Hexagon nuts for fine mechanics 螺钉－－开槽圆柱头螺钉 ISO 1207：1992 | GB /T 65-2000 | 代替 GB/T 65-1985 Slotted cheese head screws5感谢您的阅读，祝您生活愉快。
最全紧固件中英文对照
最全紧固件中英文对照，外贸必备词典！一、紧固件 Fasteners标准紧固件 Standard Fasteners非标准紧固件 Nonstandard Fasteners特殊紧固件 Special Fasteners汽车紧固件 Automotive Fasteners铜制紧固件 Brass Fasteners航天用紧固件 Aerospace Fasteners精密紧固件 Precision Fasteners化学紧固件 Chemical Fasteners摩托车紧固件 Motorcycle Fasteners不锈钢紧固件 Stainless Steel Fasteners铁道紧固件 Railway Fasteners防松紧固件 Self-locking Fasteners高强度紧固件 High strength FastenersPEM紧固件 PEM Fasteners钢结构紧固件 Steel Structural Fasteners压铆紧固件 Self-Clinching Fasteners铝制紧固件 Aluminum Fasteners钛合金紧固件 Titanium Alloy Fasteners尼龙紧固件 Nylon Fasteners精制紧固件 Finished Fastener粗制紧固件 Unfinished Fastener螺纹紧固件 Threaded Fastener半精制紧固件 Semi-Finished Fastener抗剪紧固件 Shear Fastener抗拉紧固件 Tension Fastener面板紧固件 Panel Fasteners二、螺栓 Bolts六角头螺栓Hexagon Head Bolts六角法兰面螺栓Hexagon Flange Bolts轨道螺栓（鱼尾螺丝）Track Bolts高强度螺栓 High Strength Bolts地脚螺栓Eyelet Bolts马车螺栓 Carriage Bolts护拦螺栓 Guardrail Bots焊接螺栓 Weld Bolts双头螺栓 Double End Bolts钢结构连接副 Structural Bolting内六角螺栓 Hex Socket Bolts合金钢螺栓 Alloy Steel Bolts方头螺栓 Square Head Bolts/Square Bolts钩头螺栓 Hook Bolts不锈钢螺栓 Stainless steel Bolts异型螺栓 Special Bolts吊环螺栓 Lifting Eye Bolts汽车螺栓 Automotive Bolts法兰螺栓 Flange Bolts轮胎螺栓 Wheel BoltsT型螺栓 T Bolts扁头螺栓 Pan Head Bolts蝶形螺栓 Wing Bolts沉头螺栓 Countersunk Bolts沉头方颈螺栓 Countersunk Square Neck Bolts带榫螺栓 Cup head Nib Bolts沉头双榫螺栓 Flat Countersunk Double Nib Bolts活节螺栓 Eye Bolts压铆螺栓 Clinching Bolts红打螺栓 Hot Forging Bolts圆头螺栓 Round Head Bolts圆头方颈螺栓 Round Head Square Neck Bolts圆头双榫螺栓 Round Head Fin Neck Bolts米制圆头方颈螺栓 Metric Round Head Square Neck BoltsT型带孔螺栓 T bolts withHole六角头铰制孔用螺栓 Hexagon Fit Bolts六角头螺杆带孔螺栓 Hexagon Bolts with split pin hole on shank钢网架螺栓球节点用高强度螺栓 High Strength Bolts for joints ofspace grid structures 基础螺栓 Foundation BoltsU型螺栓 U Bolts高张力螺栓 High Strength Bolts大尺寸螺栓 Big Size Bolts螺椿栓 Stud Bolts拉栓 Blind Bolts重型六角头螺栓 Heavy Hex Bolts大头马车螺栓 Step Bolts扭矩控制螺栓 T.C. Bolts蛋形颈轨道用螺栓 Elliptic Neck Track Bolts调节螺栓，调节螺钉 Pitch-Adjustable Bolts and Screws加长非标双头螺栓 Lengthen Non-Standard Stud Bolts电梯膨胀螺栓 Elevator Expansion Bolts三、螺钉 Screws?六角螺钉Hex Head Cap Screws/Hex Screws六角机械螺钉 Hex Head Machine Bolts六角法兰螺钉 Hex Flange Screws内六角孔螺丝 Hex Socket Cap Screws内六角沉头螺钉 Hex Socket Flat Countersunk Head Cap Screws紧定螺钉/固定螺钉 Set Screws止付螺钉Socket Set Screws方头紧定螺钉 Square Head Slotted Head Set Screws翼形螺钉/蝶形螺钉 Wing Screws精密螺钉 Precision Screws自攻螺钉 Self-Tapping Screws自削螺钉 Thread Cutting Screws钻尾螺钉 Self-Drilling Screws旋入螺钉 Drive Screws机械螺钉 Machine Screws木螺钉 Wood Screws家具螺钉 Furniture Screws纤维板钉/塑板螺钉 Chipboard Screws墙用螺钉 Drywall Screws剪力钉(焊接螺钉) Welding Studs螺丝附华司组合 Screws And Washers Assembled (Sems)铜螺钉 Brass Screws铝螺钉 Aluminum Screws合金钢螺钉 Alloy Steel Screws组合螺钉 SEM screws电子螺钉 Electronic Screws微小精密螺钉 Micro Screws塑料螺钉 Plastic Screws复合材料用螺钉 Particle Board Screws钛合金螺钉 Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料 Ti ,Zr ,Mo, Nb Pare Metal Bolts Parts 拇指螺丝 Thumb Screws飞机特殊扣件 Source Control Bolts电梯螺钉 Elevator Screws四角头固定螺钉 Square Set Screws单向螺钉 One Way Lag Screws管夹螺钉 Hose Clamp Screws不锈钢固定螺钉 Stainless Steel Hex Socket Cap Screws不锈钢内六角螺钉 Stainless Steel Hex Socket Cap Screws铰链螺钉 Hinge Screws货柜螺钉 Container Screws复合材料钻尾螺钉 Bi-Metal Self Drilling Screws三角牙螺钉 Tri-lobular Thread Screws高低牙螺钉 High Low Screws夹板用螺钉 Particle Board Screws马桶螺钉 Toilet Closet Bolts特长螺钉 Special Longer Screws建业螺钉 Building Fasteners不锈钢六角螺丝 Stainless Steel Hex Socket Cap Screws不锈钢特殊螺钉 Special Stainless Steel Screws宽牙螺钉（粗牙螺钉） Coarse Thread Screws链带螺钉 Collated Screws水泥螺钉 Concrete Screws板模螺钉 Construction Bolts锌蝶螺钉 Die Cast Wing Screws; Zinc Alloy重型车钉 Heavy Duty Wheel Hub Bolts内六角固定螺钉 Hex Socket Set Screws复合材料用螺钉（夹板用） Particle Board Screws犁壁螺钉 Plow Bolts不锈钢木螺丝 Stainless Steel Wood Screws套挂螺栓及螺钉 Toggle Bolts钛合金膨胀螺钉 Titanium Alloy Expansion Bolts不锈钢高低牙螺钉 Stainless Steel High-Low Thread Screws不锈钢机械螺钉 Stainless Steel Machine Screws不锈钢钻尾螺钉 Stainless Steel Self Drilling Screws不锈钢自攻螺钉 Stainless Steel Self Tapping Screws不锈钢自削螺钉 Stainless Steel Thread Cutting Screws不锈钢三角牙螺钉 Stainless Steel Tri-Lobular Thread Screws 不锈钢宽牙螺钉 Stainless Steel Coarse Thread Screws开槽沉头螺钉 Slotted Flat Countersunk Head Machine Screws 开槽盘头螺钉 Slotted Pan Head Machine Screws十字槽盘头螺钉 Cross Recessed Pan Head Machine Screws 滚花头台阶螺钉 Knurled Thurmb Screws六角头木螺钉 Hexagon Head Wood Screws平头滚花螺钉 Knurled Thin Thumb Screws?四、螺母/螺帽 Nuts六角螺母 Hexagon Nuts六角盖形螺母 Hex Cap Nuts六角锯齿螺母 Hex Serrated Nuts六角法兰螺母 Hex Flange Nuts六角平面螺母 Hex Flat Nuts六角厚螺母Hex Thick Nuts重型六角开槽螺母 Heavy Hexagon Slotted Nuts高脚螺母 Hex Coupling Nuts (High Nuts)圆螺母 Round Nuts四角螺母/四方螺母 Square Nuts四方焊接螺母 Square Weld Nuts四爪螺母Four-Claw Nuts管用螺母 Pipe Nuts轮壳螺母 Wheel Nuts蝶型螺母 Wing NutsU形螺母 U NutsT形螺母 T Nuts环首螺母 Eye Nuts齿形螺母 Kep Nuts齿花螺母 Clinch Nuts焊接螺帽 Weld Nuts压铆螺母 Self-clinching Nuts高张力螺母 High Strength Nuts建业用螺母 Structural Nuts不锈钢螺母 Stainless Steel Nuts铜螺母 Brass Nuts铝螺母 Aluminum Nuts合金钢螺母 Alloy Steel Nuts重型车螺母 Heavy Duty Wheel Hub Nuts铁器焊接袋帽 Acorn Cap Nuts金属预置扭矩式螺母 All-Metal Prevailing Torque Type Nuts壁虎螺母 Anchor Nuts大尺寸螺母 Big Size Nuts铁盖袋帽 Closed End Acorn Nuts盘形华司螺母 Conical Washer Nuts铁盖+尼龙圈组合盖帽 Din 986 Domed Cap Nuts法兰尼龙盖帽 Flange Nylon Insert Lock Nuts平面华司螺母 Flat Washer Nuts六角割沟螺母 Hex Slotted Nuts自锁螺母 Self-Locking Nuts制止螺母 Sliding NutsSLN-自动防松螺母 SLN Self-Locking Nuts特殊螺母 Special Nuts弹簧螺母 Spring Nuts不锈钢法兰螺母 Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺母 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺母 Stainless Steel Heavy Hex Nuts不锈钢六角螺母 Stainless Steel Hex Nuts不锈钢尼龙嵌入螺母 Stainless Steel Nylon Insert Lock Nuts普通六角螺母 Hex Nuts六角重型螺母 Heavy Hex Nuts薄型螺母 Hex Jam Nuts尼龙嵌入防松螺母 Nylon Insert Lock Nuts尼龙锁紧螺母Nylon Cage Nuts机械螺丝用六角螺母 Hex Machine Screw Nuts米制六角开槽螺母 Metric Slotted Hex Nuts轨道螺栓用方螺母 Track Bolt Nuts米制六角金属锁紧螺母 Prevalling Torque Hexagon Nuts开槽螺母Slotted Round Nuts六角开槽薄螺母Hexagon Slotted Thin Nuts?五、螺柱 Studs?压铆螺柱 Self-Clinching Studs铜螺柱 Brass Studs焊接螺柱 Weld Studs双头螺柱 Double End Studs六角螺柱 Hex Studs支撑卡柱 Self-Clinching Standoffs?六、垫圈 Washers弹簧垫圈 Spring Washers/Spring Lock Washers宽型弹簧垫圈 Extra-duty Helical Spring Lock Washers杯型垫圈 Cup washers波形垫圈 Wave Washers内齿垫圈 Internal Tooth Washers外齿垫圈 External Tooth Washers铜垫圈 Copper Washers方垫圈 Square Washers密封垫圈 Sealing Washers碟形弹簧垫圈 Disc Spring Washers外舌止动垫圈External Tab Washers高强度垫圈 High strengthen washers橡胶垫圈 Rubber Washers锁紧垫圈 Lock Washers平垫圈 Plain Washers鞍型弹性垫圈 Curved Spring Washers锯齿锁紧弹性垫圈 Toothed lock washers外锯齿锁紧垫圈 Serrated Lock Washers锥形垫圈 Taper Washers重型弹簧垫圈 Heavy Spring Lock Washers尼龙垫圈 Nylon Washers淬硬钢垫圈 Hardened Steel Washers?七、铆钉 Rivets?平头铆钉 Flat Head Rivets击芯铆钉 Drive Rivets彩色铆钉 Colored Rivets沉头铆钉 Countersunk Head Rivets半沉头铆钉 Oval Countersunk Head Rivets平锥头铆钉 Cone Head Rivets抽芯铆钉 Blind Rivets开口铆钉 Split Rivets开口型抽芯铆钉 Open End Blind Rivets拉铆钉 Pop Rivets封闭铆钉Closed End Rivets封闭性抽芯铆钉 Sealed Type Blind Rivets塑料铆钉 Plastic Rivets空心铆钉 Tubular Rivets环槽铆钉 Ring Groove Rivets单鼓型铆钉 Single-Grip Rivets圆头铆钉 Round Head Rivets高沉头铆钉 Countersunk Head Rivets铝铆钉 Aluminum Rivets实心铆钉 Solid Rivets沉头实心铆钉 Countersunk Head Solid Rivets灯笼铆钉 Lantern Blind Rivets半空心铆钉 Semi-Tubular Rivets圆头半空心铆钉 Semi-tubular Pan Head Rivets异型铆钉 Special Rivets不锈钢铆钉 Stainless Steel Rivets双鼓型铆钉 Multi-grip Rivets高强度铆钉 High Strength Rivets台阶铆钉 Step Rivets面板铆钉 Tablet Rivets开花型抽芯铆钉 Flowering Blind Rivets拉花型抽芯铆钉 Peel Type Blind Rivets沟槽型抽芯铆钉 Grooved Type Blind Rivet铆接工具 Riveting Tool?八、壁虎（膨胀螺栓）Anchors/Expansion Bolts化学锚栓 Chemical Anchors打入式壁虎 Hammer Drive Anchors内迫壁虎 Drop in Anchors重型壁虎 Heavy Duty Anchors锤钉壁虎 Hit Anchors中空壁虎 Hollow Wall Anchors套管壁虎 Sleeve Anchors插片壁虎 Ceiling Anchors门窗、地板专用壁虎 Nylon Frame Anchors or Metal frame Anchors电梯壁虎 Bolt Anchors车修壁虎 Wedge Anchors鱼眼壁虎 Tie Wire Anchors外迫壁虎 Cut Anchors塑料膨胀 Plastic Anchors不锈钢重载胀栓 Heavy Duty Expansion Anchors象脚壁虎 Elephant Foot Anchors长型兰花夹 Short Strap Anchors?九、销 Pins?开口销 Split Pins圆锥销 Taper Pins锁销 Lock Pins销轴 Clevis Pins with head槽销 Grooved Pins弹性销 Spring Pins圆柱销 Parallel Pins弹性圆柱销 Slotted Spring Pins带孔销 Pins with split pin hole?十、挡圈 Circlips/Rings?开口挡圈 E rings孔用挡圈 Circlips for holes轴用钢丝挡圈 Roundwire Snap Rings for shaft轴肩挡圈Rings for shoulder夹紧挡圈 Grip Rings轴用卡簧 Circlips for shafts带齿轴用挡圈 Retaining Rings with Lugs for shafts钢丝锁圈 Round wire Circlips锥形锁紧挡圈 Lock Rings with cone pins?十一、其他 Others?牙条 Threaded Rod冲压件 Stampings平键 Parallel Keys半圆键 Woodruff Keys扳手 Spanners钢丝螺套 Wire Thread Insert自动车床车削件 CNC Turning Parts齿轮 Gears模具 Molds线材盘元 Iron or steel wire rod铰链 Hinge表面处理 Surface Treatment。
紧固件各类产品名称术语中英文对照表
---------------------------------------------------------------最新资料推荐------------------------------------------------------ 紧固件各类产品名称术语中英文对照表紧固件各类产品名称术语中英文对照表1.紧固件定义 1.1 紧固件Fastener 1.2 商品紧固件Commercial Fastener 1.3 标准紧固件Standard Fastener 1.4 非标准紧固件Nonstandard Fastener 1.5 特殊紧固件Special Fastener 1.6 精制紧固件Finished Fastener 1.7 粗制紧固件Unfinished Fastener 1.8 螺纹紧固件Threaded Fastener 1.9 半精制紧固件Semi-Finished Fastener 1.10 有头紧固件Headed Fastener 1.11 无头紧固件Headless Fastener 1.12 压力紧固件Compression Fastener 1.13 高强度紧固件High strength Fastener 1.14 抗剪紧固件Shear Fastener 1.15 抗拉紧固件Tension Fastener 1.16 库存紧固件Stock Fastener 2.头部型式及扳拧特征 2.1 六角头Hexagon head 2.2 六角头垫圈面Hexagon head with washer face 2.3 六角头凸缘Hexagon head with collar 2.4 六角头法兰面Hexagon head with flange 2.5 方头Square head 2.6 方头、凸缘Square head with collar 2.7 三角头Triangle head 2.8 三角头、凸缘Triangle head with collar 2.9 人角头Oct-agonal head 2.10 12角头、法兰面12 point flange head (bihexagonal head) 2.11 T型头T head ( hammer head ) 2.12 圆头Round head ( button head ) 2.13 扁圆头Mushroom head ( truss head ) 2.14 圆柱头Cheese head ( flat fillister head ) 2.15 球面圆柱头Raised cheese head ( fillister head ) 2.16 盘头Pan head 2.17 沉头1/ 11Countersunk head ( flat head) ( c s k head ) 2.18 双沉头Reinforced head ( double cone ) 2.19 半沉头Raised countersunk head ( oval head ) 2.20 球面扁圆柱头Binging head 2.21 沉头清根Undercut countersunk head ( undercut flat head ) 2.22 半沉头清根Undercut raised countersunk head ( undercut oval head ) 2.23 球体头Ball head 2.24 按纽头Button head 2.25 无头Headless 2.26 圆形垫圈头Round washer head 2.27 内六角头Socket head 2.28 高圆头High botton head 2.29 双层头Biconic head 2.30 锥头Cone head 2.31 尖锥头Steeple head 2.32 喇叭头Bugle head 2.33 薄片头thin wafer 2.34 冲压凹穴型头Drilled fillister head 2.35 伞形头Stuss head 2.36 蘑菇头Mushroom head 2.37 支承面Bearing surface 2.38 垫圈面Washer face 2.39 六角Hexagon 2.40 四方Square 2.41 三角Triangle 2.42 人角Octagon 2.43 12角12 point (bihexagonal ) 2.44 内六角Hexagon socket 2.45 内三角Triangle socket 2.46 内四角Square socket 2.47 内六花键Six-spline socket 2.48 内12角12 point socket ( bihexagon socket ) 2.49 开槽Slot 2.50 十字槽 H Cross recess ( phillips ) 2.51 十（米）字槽Cross recess ( pozidriv ) 2.52 蝶形（翼形） Wing 2.53 旋棒Tommy 2.54 直纹滚花Straight knurl 2.55 网纹滚花Diamond knurl 2.56 十字孔Cross hole ( set pin hole in side ) 2.57 五角Pentagon 2.58 梅花槽Torx recess 2.59 离合槽Clutch recess 2.60 四方槽Square recess 3.杆部及其末端---------------------------------------------------------------最新资料推荐------------------------------------------------------ 3.1 标准杆Normal shank ( nominal shank diameter=nominal thread diameter) 3.2 细杆Reduced shank ( shank diameter<minor diameter ) 3.3 腰状杆Waisted shank ( shank diameter> thread diameter )1/53/ 113.4 加强杆Increased shank ( shank diamerer> thread diameter ) 3.5 轴杆Shouder ( collar ) 3.6 方颈Square neck 3.7 榫Fin 3.8 凸缘Fillet 3.9 锯齿形Serration 3.10 肋Lug 3.11 条颈Ribbed neck 3.12 胀大颈Swell neck WINDFAST-QC.DEP. page3of12 Record 2008-3-3 No. Chinese Description in English 3.13 杆(部)体Shank 3.14 锥端Cone point 3.15 截锥端Short dog point 3.16 凹端Cup point 3.17 短圆柱端Short dog point 3.18 长圆柱端Long dog point 3.19 短圆柱球面端Short dog point with rounded end 3.20 短圆柱截锥端Short dog point with truncated cone end 3.21 刮销端Scrape point 3.22 自攻螺钉的末端End for self-tapping screws 3.23 自攻锁紧螺钉的末端End for thread rolling screws (thread formed by deformation ) 3.24 辗制末端As-roller end 3.25 平端Flat point 3.26 球面端(倒圆端) Rounded end 3.27 倒角端Chamfered end 3.28 钻孔端Gimlet point 3.29 顶锻端Header point 3.30 钉子端Nail point 3.31 针端Needle point 3.32 半圆端Oval point 3.33 导向端Pilot point 3.34 球端Spherical point 3.35 夹断端Pinck point4.尺寸及形位公差 4.1 实际尺寸Actual size 4.2 允差Allawance size 4.3 基本尺寸Basic size 4.4 设计尺寸Design size 4.5 配合Fit 4.6 尺寸极限Limits of size 4.7 公称尺寸Nominal size 4.8 参改尺寸Reference size4.9 公差Tolerance 4.10 公差位置Position tolerance 4.11 对边宽度Width across flats 4.12 对角宽度Width across corner---------------------------------------------------------------最新资料推荐------------------------------------------------------ 4.13 螺纹通(测量) Go thread gauge 4.14 螺纹止(测量) No go thread gauge 4.15 头下圆角半径Radius under head 4.16 开槽宽度Slot recess width 4.17 开槽深度Slot recess depth 4.18 十字槽插入深Penetration depth 4.19 十字槽直径Recess diameter 4.20 十字槽宽度Recess width 4.21 头部直径Head diameter 4.22 头部高度Head height 4.23 头部角度Head angle 4.24 无螺纹杆径Shank diameter ( unthreaded diameter ) 4.25 无螺纹杆长Shank length ( unthreaded length ) 4.26 夹紧长度Grip length 4.27 螺纹大径Major thread diameter 4.28 螺纹小径Minor diameter ( small ) 4.29 肩距Unthreaded length under head 4.30 螺纹长度Thread length 4.31 杆长Total length 4.32 内六角扳拧深度Depth hexagon socket 4.33 内凹槽插入深度Key engagement 4.34 外径Exter diameter ( outside diameter ) 4.35 内径Internal diameter ( inside diameter ) 4.36 长度Length 4.37 宽度Breadth 4.38 厚度Thickness 4.39 高度Hight 4.40 孔径Bore diameter 4.41 法兰直径Flange diamerer 4.42 方径长度Square neck length 4.43 方径宽度Square neck width 4.44 凸缘高度Collar height 4.45 凸缘直径Collar diameter 4.46 对称度Symmerty 4.47 同轴度Concentricity ( coaxiality ) 4.48 垂直度Perpendicularity 4.49 平行度Parallelism 4.5 直度Straightriess 4.51 槽杆同轴度Recess concentricity 4.52 头杆同轴度Head concentricity5/ 114.53 头杆垂直度Head lnclination2/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 4.54 斜度Angularity ( taper ) 4.55 弧度或弯曲度Bow or camber 4.56 尾尖角Point angle 4.57 镀锌层厚度Zinc plating thickness 4.58 跳动Run-out 4.59 锥度Taper ratio 4.60 榫长Nib length4.61 榫宽Nib width 4.62 倒角.圆角Chamfer 4.63 平面度Flatness5.机械性能 5.1 抗拉强度Tensile strength 5.2 屈服强度Proof strength 5.3 屈服点Lower yield stress 5.4 扭转强度Torque strength ( torsional strength ) 5.5 剪切强度Shear strength 5.6 冲击韧性Impact strength 5.7 延伸率Elongation 5.8 断面收缩率Reduction 5.9 拉(压)应力Tension 5.10 破坏(扭)力矩Breaking torque 5.11 晶粒度Grahularity 5.12 机械性能Mechanical properties 5.13 脱碳Decarburise 5.14 渗碳Carburization 5.15 最小剩余弹力Minimum residual sping force 5.16 压负荷的百分率Percenatage of compression load 5.17 表面硬度Surface hardness 5.18 芯部硬度Core hardness 5.19 扭矩Torque ( torsion ) 5.20 表面硬化层深度Case harden depth 5.21 氢脆Hydrogen embrittlement 5.22 压载(负)荷Compression load 5.23 硬度试验Hardness test 5.24 头部坚固性试验Head soundness test 5.25 扭转试验Twisting test 5.26 弹性试验Resilience test 5.27 保证载荷试验Proof loading test 5.28 楔负载强度试验Wedge loading test 5.29 弯曲试验Bending test 5.30 旋入试验Screw-in test 5.31 最小破坏力矩试验Torsional test and minimum torques7/ 115.32 永久变形试验Permanent deformation test 5.33 盐雾试验Salt spray test 5.34 弹性Elasticity5.35 韧性Tenacity ( Toughnee ) 5.36 塑性Fiexibility 5.37 磁力碳伤Magnetic particle inspection6.材料-热处理-表面处理 6.1 碳钢Carbon steel 6.2 低碳钢Low carbon steel 6.3 中碳钢Medium carbon steel 6.4 合金钢Alloy steel 6.5 热处理钢Heat-treated steel 6.6 低马钢Low carbon martensite steel 6.7 奥氏体不锈钢Austenitic stainless steel 6.8 马氏体不锈钢Martenitic stainless steel 6.9 铁Iron 6.10 铝Aluminium 6.11 黄铜Brass 6.12 紫铜Copper 6.13 青铜Bronze 6.14 塑料Plastic 6.15 淬火Quenched 6.16 回火Tempered 6.17 退火Annealed 6.18 表面硬化Case hardened 6.19 强度等级Class 6.20 氧化Oxide ( anodizing ) 6.21 金属Metal 6.22 非金属Metalloid 6.23 发黑Black 6.24 本色Plain ( self colour ) 6.25 热处理Heat treatment 6.26 涂层Coating 6.27 表面处理Finish 6.28 涂蜡Waxed 6.29 镀锌(兰白锌) Zinc plated ( zinc / clear ) 6.30 镀黄锌Zinc yellow ( Y.Z.P.)6.31 镀黑锌Zinc plated black 6.32 镀镍Nickel plated 6.33 镀铜Brass plated 6.34 热浸镀锌Hot dip galvanized ( H.D.G.) 6.35 电镀Electplating 6.36 机械镀锌Mechanical galvaizing 6.37 表面热处理Surface heat treatment 7、加工方法7.1 冷镦Cold heading 7.2 冷锻Cold forging 7.3 热锻Hot forging 7.4 成型Forming 7.5 切削(断) Cutting3/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 7.6 缩径Shrink diameter 7.7 搓(攻)丝Threading 7.8 滚丝Thread rolling 7.9 拔丝Drawing 7.10 酸洗Pickling 7.11 钝化Passirating 7.12 废水处理Waste water treatment 7.13 研磨Grinding 7.14 镦粗Upsetting 7.15 开槽Soltting 7.16 刮削Sharing 7.17 滚花Kunrling 7.18 抛光Polishing 7.19 冲压Punching 7.20 滚动Tumbling 7.21 精整Trimming 7.22 铣削Milled 7.23 挤压Extruding 7.24 钻孔Drilling 7.25 模压Embossing 7.26 沉孔Countersinking 7.27 压印Coining 7.28 扩孔Counterboring 7.29 控削Broaching 7.30 辊光Burnishing 7.31 锻造Forging 7.32 剪切Shear 7.33 焊接Welded 7.34 喷砂Sand blasting 8.表面缺陷 8.1 裂缝Cracks 8.2 淬火裂缝Quench cracks 8.3 锻造裂缝Forging cracks 8.4 锻造爆裂Forging bursts 8.5 剪切爆裂Shear bursts 8.6 条痕Laps 8.7 凹痕Voids 8.8 皱纹Folds ( pits ) ( laps ) 8.9 切痕Tool marks 8.10 损伤Damages 8.11 毛刺Burr 8.12 碎屑Chip 8.13 夹杂Inclusions 8.14 锈皮Sharing 8.15 飞边Flash 8.16 开裂Cracks 8.17 锈、锈斑Rust9.螺纹 9.1 普通螺纹Screw thread 9.2 锥螺纹Taper screws thread 9.3 自攻螺纹(宽牙螺纹) Tapping screws thread ( spaced thread ) 9.4 木螺钉螺纹Wood screws thread 9.5 米制螺纹Metric thread 9.6 ISO 米制螺纹ISO Metric thread 9.7 米制细牙螺纹Metric fine pitch thread 9.8 ISO 米制细牙螺纹ISO Metric fine pitch thread 9.99/ 11寸制螺纹Inch thread 9.10 统一螺纹(ISO寸制) Unified screw thread ( ISO inch ) 9.11 惠氏螺纹Whitworth thread 9.12 管螺纹Pipe thread 9.13 惠氏管螺纹Whitworth pipe thread 9.14 螺旋线Helix 9.15 螺旋面Helical surface 9.16 外螺纹External thread 9.17 内螺纹Inernal thread 9.18 牙侧Flank 9.19 沟槽Groove 9.20 凸起Ridge 9.21 牙顶Crest 9.22 牙底Root 9.23 螺纹牙型Thread profile 9.24 螺纹线Thread 9.25 单线螺纹Single--start--thread 9.26 多线螺纹Multi--start--thread 9.27 右旋螺纹Right--start--thread 9.28 左旋螺纹Left--start--thread 9.29 工作牙侧Pressure ( load ) flank 9.30 非工作牙侧Clearing ( clearance ) flank 9.31 牙底的圆角半径Root radius 9.32 牙型高度Height ( or depth ) of thread 9.33 牙型角Included angle 9.34 牙型半角Flank lead 9.35 中径线Pitch line 9.36 螺纹轴线Axis of thread 9.37 导程Flank lead 9.38 双牙导程Dual flank lead 9.39 螺距Flank pitch 9.40 双牙螺距Dual flank lead 9.41 大径Major diameter 9.42 小径Minor diameter 9.43 中径Pitch diameter4/5---------------------------------------------------------------最新资料推荐------------------------------------------------------ 9.44 9.45 9.46 9.47 9.48 9.49 9.50单一中径Simple pitch diameter 作用中径Virtual pitch diameter 螺纹升角Lead angle 基本牙型Basic profile 伞状螺纹Umbrella thread 粗牙螺纹Coarse thread 细牙螺纹Fine thread5/511/ 11。
(整理)紧固件中英文对照表Terminologyforfastener
非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert)六角开槽螺母Hexagon slotted nuts六角开槽螺母细牙Hexagon slotted and castle nuts-Fine pitch thread六角螺母Hexagon nuts六角螺母－细牙Hexagon nuts-Fine pitch thread全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts120度半沉头铆钉120degree oval countersunk rivets120度沉头半空心铆钉120 degree countersunk head semi-tubular rivets120度沉头铆钉120 degree countersunk head rivetsT形槽用螺栓Bolts for T-Slot鞍形弹簧垫圈Curved single coil spring lock washers鞍形弹性垫圈Curved spring washers半圆头带榫螺栓Cup head nib bolts半圆头低方颈螺栓Cup square neck bolts with short neck半圆头方颈螺栓Cup head square neck bolts半圆头铆钉Round head rivets扁平头铆钉Thin head rivets扁圆头半空心铆钉Oval head semi-tubular rivets扁圆头铆钉Flat round head rivets标牌铆钉Rivets for name plate标准型弹簧垫圈Single coil spring lock washers, Normal type波形弹簧垫圈Wave single coil spring lock washers波形弹性垫圈Wave spring washers槽钢用方斜垫圈Square taper washers for slot section槽销Grooved pins侧面带孔圆螺母Round nuts with set pin holes in side沉头半空心铆钉Countersunk head semi-tublar rivets沉头带榫螺栓Flat countersunk nib bolts沉头方颈螺栓Flat countersunk square neck bolts沉头铆钉Countersunk head rivets沉头双榫螺栓Flat countersunk double nib bolts大半圆头带榫螺栓Cup head nib bolts with large head大半圆头方颈螺栓Cup head square neck bolts with large head大扁圆头半空心铆钉Truss head semi-tubuar rivets大扁圆头铆钉Truss head rivets带槽圆螺母Slotted round nuts带孔销Pins with split pin hole带锁圈的螺钉锁紧挡圈Lock rings with screw and circlip单耳止动垫圈Tab washers with log tab弹性圆柱销Spring-type straight pins-Slotted等长双头螺柱Double end studs地脚螺栓Eyelet bolts吊环螺钉Eyebolts蝶形螺母Wing nuts端面带孔圆螺母Round nuts with drilled holes in one face方螺母Square nuts方头凹端紧定螺钉Square set screws with cup point方头长圆柱端紧定螺钉Square set screws with long dog point方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end方头倒角端紧定螺钉Square set screws with chamfered end方头短圆柱锥端紧定螺钉Square set screws with short dog point and cone end非金属嵌件六角法兰面锁紧螺母Prevailing torque type hexagon nuts with flange (with non-metallic insert)封闭型扁圆头抽芯铆钉Mushroom head break mandrel closed end blind rivets封闭型沉头抽芯铆钉120 deg flush head break mandrel closed end blind rivets盖形螺母Acorn nuts工字钢用方斜垫圈Square taper washers for I section管状铆钉Pope type rivets滚花薄螺母Knurled nuts滚花高螺母Knurled nut with collar滚花高头螺钉Knurled thumb screws滚花头不脱出螺钉Knurled thumb screws with waisted shank滚花小头螺钉Knurled screws with small head焊接方螺母Square weld nuts焊接六角螺母Hexagon weld nuts环形螺母Lifting nuts活节螺栓Eye bolts机动弧焊用焊接螺柱Weld studs for are welding夹紧挡圈Grip rings开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank开槽半沉头螺钉Slotted raised countersunk head screws开槽半沉头自攻螺钉Slotted raised countersunk head tapping screws开槽长圆柱端紧定螺钉Slotted set screws with long dog point开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank开槽沉头螺钉Slotted countersunk head screws开槽沉头自攻螺钉Slotted countersunk head tapping screws开槽盘头螺钉Slotted pan head screws开槽带孔球面圆柱头螺钉Slotted capstan screws开槽盘头螺钉Slotted pan head screws开槽盘头自攻螺钉Slotted pan head tapping screws开槽平端紧定螺钉Slotted set screws with flat point开槽球面大圆柱头螺钉Slotted large raised cheese head screws开槽球面圆柱头轴位螺钉Slotted raised cheese head with shoulder开槽无头轴位螺钉Slotted shoulder screws开槽圆柱端定位螺钉Slotted setscrews with dog point开槽圆柱头螺钉Slotted cheese head screws开槽圆柱头轴位螺钉Slotted cheese head screws with shoulder开槽锥端定位螺钉Slotted setscrews with cone point开口挡圈“E” rings开口垫圈Washers with split开口销Split pins开口型扁圆头抽芯铆钉Mushroom head break mandrel blind rivets开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivets开尾圆锥销Taper pins with split空心铆钉Tubular rivets孔用弹性挡圈Circlips for holes孔用钢丝挡圈Roundwire snap rings for hole扣紧螺母Tight nuts六角法兰面螺母Hexagon nuts with flange六角法兰面自钻自攻螺钉Hexagon flange head self-drilling tapping screws六角头螺栓、弹簧垫圈和平垫圈组合件Hexagon head bolt, single coil spring lock washer and plain washer assemblies六角头螺栓和平垫圈组合件Hexagon head bolt and plain washer assemblies六角头螺栓和外锯齿锁紧垫圈组合件Hexagon head bolt and serrated lock washer external teeth assemblies六角头头部戴槽螺栓Hexagon bolts with slot on head六角头头部带孔螺栓Hexagon blots with wire holes on head六角头自攻螺钉Hexagon head tapping screws六角头自攻螺钉和大垫圈组合件Hexagon head tapping screw and plain washer assemblies六角头自攻锁紧螺钉Hexagon head thread forming screws六角自锁螺母Self-locking nuts, hexagon内齿锁紧垫圈Lock washers internal teeth。
最全紧固件中英文对照
最全紧固件中英文对照，外贸必备词典！一、紧固件Fasteners标准紧固件StandardFasteners非标准紧固件NonstandardFasteners特殊紧固件SpecialFasteners汽车紧固件AutomotiveFasteners铜制紧固件BrassFasteners航天用紧固件AerospaceFasteners精密紧固件PrecisionFasteners化学紧固件ChemicalFasteners摩托车紧固件MotorcycleFasteners不锈钢紧固件StainlessSteelFasteners铁道紧固件RailwayFasteners防松紧固件Self-lockingFasteners高强度紧固件HighstrengthFastenersPEM紧固件PEMFasteners钢结构紧固件SteelStructuralFasteners压铆紧固件Self-ClinchingFasteners铝制紧固件AluminumFasteners钛合金紧固件TitaniumAlloyFasteners尼龙紧固件NylonFasteners精制紧固件FinishedFastener粗制紧固件UnfinishedFastener螺纹紧固件ThreadedFastener半精制紧固件Semi-FinishedFastener抗剪紧固件ShearFastener抗拉紧固件TensionFastener面板紧固件PanelFasteners二、螺栓Bolts六角头螺栓HexagonHeadBolts六角法兰面螺栓HexagonFlangeBolts轨道螺栓（鱼尾螺丝）TrackBolts高强度螺栓HighStrengthBolts地脚螺栓EyeletBolts马车螺栓CarriageBolts护拦螺栓GuardrailBots焊接螺栓WeldBolts双头螺栓DoubleEndBolts钢结构连接副StructuralBolting内六角螺栓HexSocketBolts合金钢螺栓AlloySteelBolts复合材料用螺钉（夹板用）ParticleBoardScrews犁壁螺钉PlowBolts不锈钢木螺丝StainlessSteelWoodScrews套挂螺栓及螺钉ToggleBolts钛合金膨胀螺钉TitaniumAlloyExpansionBolts不锈钢高低牙螺钉StainlessSteelHigh-LowThreadScrews 不锈钢机械螺钉StainlessSteelMachineScrews不锈钢钻尾螺钉StainlessSteelSelfDrillingScrews不锈钢自攻螺钉StainlessSteelSelfTappingScrews不锈钢自削螺钉StainlessSteelThreadCuttingScrews不锈钢三角牙螺钉StainlessSteelTri-LobularThreadScrews 不锈钢宽牙螺钉StainlessSteelCoarseThreadScrews开槽沉头螺钉SlottedFlatCountersunkHeadMachineScrews 开槽盘头螺钉SlottedPanHeadMachineScrews十字槽盘头螺钉CrossRecessedPanHeadMachineScrews 滚花头台阶螺钉KnurledThurmbScrews六角头木螺钉HexagonHeadWoodScrews平头滚花螺钉KnurledThinThumbScrews?四、螺母/螺帽Nuts六角螺母HexagonNuts六角盖形螺母HexCapNuts六角锯齿螺母HexSerratedNuts六角法兰螺母HexFlangeNuts六角平面螺母HexFlatNuts六角厚螺母HexThickNuts重型六角开槽螺母HeavyHexagonSlottedNuts高脚螺母HexCouplingNuts(HighNuts)圆螺母RoundNuts四角螺母/四方螺母SquareNuts四方焊接螺母SquareWeldNuts四爪螺母Four-ClawNuts管用螺母PipeNuts轮壳螺母WheelNuts蝶型螺母WingNutsU形螺母UNutsT形螺母TNuts环首螺母EyeNuts齿形螺母KepNuts齿花螺母ClinchNuts焊接螺帽WeldNuts压铆螺母Self-clinchingNuts高张力螺母HighStrengthNuts建业用螺母StructuralNuts不锈钢螺母StainlessSteelNuts铜螺母BrassNuts铝螺母AluminumNuts合金钢螺母AlloySteelNuts重型车螺母HeavyDutyWheelHubNuts铁器焊接袋帽AcornCapNuts金属预置扭矩式螺母All-MetalPrevailingTorqueTypeNuts壁虎螺母AnchorNuts大尺寸螺母BigSizeNuts铁盖袋帽ClosedEndAcornNuts盘形华司螺母ConicalWasherNuts铁盖+尼龙圈组合盖帽Din986DomedCapNuts法兰尼龙盖帽FlangeNylonInsertLockNuts平面华司螺母FlatWasherNuts六角割沟螺母HexSlottedNuts自锁螺母Self-LockingNuts制止螺母SlidingNutsSLN-自动防松螺母SLNSelf-LockingNuts特殊螺母SpecialNuts弹簧螺母SpringNuts不锈钢法兰螺母StainlessSteelFlangeNuts不锈钢六角轮缘尼龙螺母StainlessSteelFlangeNylonInsertLockNuts 不锈钢六角重型螺母StainlessSteelHeavyHexNuts不锈钢六角螺母StainlessSteelHexNuts不锈钢尼龙嵌入螺母StainlessSteelNylonInsertLockNuts普通六角螺母HexNuts六角重型螺母HeavyHexNuts薄型螺母HexJamNuts尼龙嵌入防松螺母NylonInsertLockNuts尼龙锁紧螺母NylonCageNuts机械螺丝用六角螺母HexMachineScrewNuts米制六角开槽螺母MetricSlottedHexNuts轨道螺栓用方螺母TrackBoltNuts米制六角金属锁紧螺母PrevallingTorqueHexagonNuts开槽螺母SlottedRoundNuts六角开槽薄螺母HexagonSlottedThinNuts?五、螺柱Studs?压铆螺柱Self-ClinchingStuds铜螺柱BrassStuds焊接螺柱WeldStuds双头螺柱DoubleEndStuds六角螺柱HexStuds支撑卡柱Self-ClinchingStandoffs?六、垫圈Washers弹簧垫圈SpringWashers/SpringLockWashers宽型弹簧垫圈Extra-dutyHelicalSpringLockWashers杯型垫圈Cupwashers波形垫圈WaveWashers内齿垫圈InternalToothWashers外齿垫圈ExternalToothWashers铜垫圈CopperWashers方垫圈SquareWashers密封垫圈SealingWashers碟形弹簧垫圈DiscSpringWashers外舌止动垫圈ExternalTabWashers高强度垫圈Highstrengthenwashers橡胶垫圈RubberWashers锁紧垫圈LockWashers平垫圈PlainWashers鞍型弹性垫圈CurvedSpringWashers锯齿锁紧弹性垫圈Toothedlockwashers外锯齿锁紧垫圈SerratedLockWashers锥形垫圈TaperWashers重型弹簧垫圈HeavySpringLockWashers尼龙垫圈NylonWashers淬硬钢垫圈HardenedSteelWashers?七、铆钉Rivets?平头铆钉FlatHeadRivets击芯铆钉DriveRivets彩色铆钉ColoredRivets沉头铆钉CountersunkHeadRivets半沉头铆钉OvalCountersunkHeadRivets平锥头铆钉ConeHeadRivets抽芯铆钉BlindRivets开口铆钉SplitRivets开口型抽芯铆钉OpenEndBlindRivets拉铆钉PopRivets封闭铆钉ClosedEndRivets封闭性抽芯铆钉SealedTypeBlindRivets塑料铆钉PlasticRivets空心铆钉TubularRivets环槽铆钉RingGrooveRivets单鼓型铆钉Single-GripRivets圆头铆钉RoundHeadRivets高沉头铆钉CountersunkHeadRivets铝铆钉AluminumRivets实心铆钉SolidRivets沉头实心铆钉CountersunkHeadSolidRivets灯笼铆钉LanternBlindRivets半空心铆钉Semi-TubularRivets圆头半空心铆钉Semi-tubularPanHeadRivets异型铆钉SpecialRivets不锈钢铆钉StainlessSteelRivets双鼓型铆钉Multi-gripRivets高强度铆钉HighStrengthRivets台阶铆钉StepRivets面板铆钉TabletRivets开花型抽芯铆钉FloweringBlindRivets拉花型抽芯铆钉PeelTypeBlindRivets沟槽型抽芯铆钉GroovedTypeBlindRivet铆接工具RivetingTool?八、壁虎（膨胀螺栓）Anchors/ExpansionBolts化学锚栓ChemicalAnchors打入式壁虎HammerDriveAnchors内迫壁虎DropinAnchors重型壁虎HeavyDutyAnchors锤钉壁虎HitAnchors中空壁虎HollowWallAnchors套管壁虎SleeveAnchors插片壁虎CeilingAnchors门窗、地板专用壁虎NylonFrameAnchorsorMetalframeAnchors电梯壁虎BoltAnchors车修壁虎WedgeAnchors鱼眼壁虎TieWireAnchors外迫壁虎CutAnchors塑料膨胀PlasticAnchors不锈钢重载胀栓HeavyDutyExpansionAnchors象脚壁虎ElephantFootAnchors长型兰花夹ShortStrapAnchors?九、销Pins?开口销SplitPins圆锥销TaperPins锁销LockPins销轴ClevisPinswithhead槽销GroovedPins弹性销SpringPins圆柱销ParallelPins弹性圆柱销SlottedSpringPins带孔销Pinswithsplitpinhole?十、挡圈Circlips/Rings?开口挡圈Erings孔用挡圈Circlipsforholes轴用钢丝挡圈RoundwireSnapRingsforshaft 轴肩挡圈Ringsforshoulder夹紧挡圈GripRings轴用卡簧Circlipsforshafts带齿轴用挡圈RetainingRingswithLugsforshafts 钢丝锁圈RoundwireCirclips锥形锁紧挡圈LockRingswithconepins?十一、其他Others?牙条ThreadedRod冲压件Stampings平键ParallelKeys半圆键WoodruffKeys扳手Spanners钢丝螺套WireThreadInsert自动车床车削件CNCTurningParts齿轮Gears模具Molds线材盘元Ironorsteelwirerod铰链Hinge表面处理SurfaceTreatment。
紧固件中英文对照大全
--------------------------------------------------------------------------------螺栓－－方头螺栓C级UDC 621.882.6 | GB 8-88 | 代替GB8-76Square head bolts-Product grade C－－沉头方颈螺栓UDC 621.882.6 | GB 10-88 | 代替GB10-76Flat countersunk square neck bolts－－沉头带榫螺拴UDC 621.882.6 | GB 11-88 | 代替GB11-76Flat countersunk nib bolts－－半圆头方颈螺栓UDC 621.882.6 | GB 12-88 | 代替GB12-76Cup head square neck bolts－－半圆头带榫螺栓UDC 621.882.6 | GB 13-88 | 代替GB13-76Cup head nid bolts－－大半圆头方颈螺栓C级ISO 8677:1986 | GB 14-1998 | 代替GB14-88Cup head square neck bolts with large head-Product grade C－－大半圆头带榫螺栓UDC 621.882.6 | GB 15-88 | 代替GB15-76Cup head nib bolts with large head－－六角头铰制孔用螺栓UDC 621.882.6 | GB 27-88 | 代替GB27-76Hexagon fit bolts-product grade A and B－－六角头螺杆带孔铰制孔用螺栓UDC 621.882.6 | GB 28-88 | 代替GB28-76Hexagon fit bolts with split pin hole on shank-product grade A and B－－六角头头部带槽螺栓A 和B 级UDC 621.882.6 | GB 29.1-88 | 代替GB29-76 Hexagon bolts with slot on head -product A and B－－十字槽凹穴六角头螺栓UDC 621.882.6 | GB 29.2-88 | 代替GB29-76Cross recessed hexagon bolts with indentation－－六角头螺杆带孔螺栓UDC 621.882.6 | GB 31.1-88 | 代替GB31、23、24-76 Hexagon bolts with split pin hole on shank-product grade A and B－－六角头螺杆带孔螺栓细杆B级UDC 621.882.6 | GB 31.2-88 | 代替GB31、23、24-76 Hexagon bolts with split pin hole on shank-Reduced shank-product grade B－－六角头螺杆带孔螺栓细牙A和B级UDC 621.882.6 | GB 31.3-88 | 代替GB31、23、24-76Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and B－－六角头头部带孔螺栓A 和B级UDC 621.882.6 | GB 32.1-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-product grade A and B－－六角头头部带孔螺栓细杆B级UDC 621.882.6 | GB 32.2-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-Reduced shank-product grade B－－六角头头部带孔螺栓细牙A 和 B 级UDC 621.882.6 | GB 32.3-88 | 代替GB32、25、26-76Hexagon bolts with wire holes on head-Fine pitch thread-product grade A and B－－下方头螺栓B级UDC 621.882.6 | GB 35-88 | 代替GB35-76Square head bolts with small head-praduct grade B－－T 形槽用螺栓UDC 621.882.6 | GB 37-88 | 代替GB37-76Bolts for T-Slot－－加强半圆头方颈螺栓GB /T794-93 | 代替GB794-67Strengthened cup head square neck bolts－－活节螺栓UDC 621.882.6 | GB 798-88 | 代替GB798-76Eye bolts－－地脚螺栓UDC 621.882.6 | GB 799-88 | 代替GB799-76Eyelet bolts－－沉头双榫螺UDC 621.882.6 | GB 800-88 | 代替GB800-77Flat countersunk double nib bolts－－小圆半头低方颈螺栓B级ISO 8678:1988 | GB /T 801-1998 | 代替GB801-88Cup head square neck bolts with small head and short neck-product grade B－－六角头螺栓C级ISO 4016:1999 | GB /T 5780-2000 | 代替GB/T 5780-1986 Hexagon head bolts-product grade C－－六角头螺栓全螺纹C级ISO 4018:1999 | GB /T 5781-2000 | 代替GB/T 5781-1986 Hexagon head bolts-Full thread-product grade C－－六角头螺栓ISO 4014：1999 | GB /T 5782-2000 | 代替GB/T 5782-1986Hexagon head bolts－－六角头螺栓全螺纹ISO 4017：1999 | GB /T 5783-2000 | 代替GB/T 5783-1986 Hexagon head bolts-Full thread－－六角头螺栓-细杆-B级UDC 621.882.6 | GB 5784-86 | 代替GB30、21-76Hexagon head bolts-Reduced shank -Product grade B－－六角头螺栓细牙ISO 8765：1999 | GB /T 5785-2000 | 代替GB/T 5785-1986 Hexagon head bolts with fine pitch thread－－六角头螺栓细牙全螺纹ISO 8676：1999 | GB /T 5786-2000 | 代替GB/T 5786-1986 Hexagon head bolts with fine pitch thread-Full thread－－六角法兰面螺栓-加大系列-B级UDC 621.882.6 | GB 5789-86 |Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓-加大系列-细杆-B级UDC 621.882.6 | GB 5790-86 |Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓小系列ISO 4162：1990 | GB /T 16674-1996 | 代替GB/T 5787、5788-1986Hexagon flange bolts-Small series－－钢网架螺栓球节点用高强度螺栓GB /T 16939-1997 |High strength bolts for joints of space grid structures螺柱－－双头螺柱bm=1d UDC 621.882 | GB 897-88 | 代替GB897-76Double end studs-bm=1d－－双头螺柱bm=1.25d UDC 621.882 | GB 898-88 | 代替GB898-76Double end studs-bm=1.25d－－双头螺柱bm=1.5d UDC 621.882 | GB 899-88 | 代替GB899-76Double end studs-bm=1.5d－－双头螺柱bm=2d UDC 621.882 | GB 900-88 | 代替GB900-76Double end studs--bm=2d－－等长双头螺柱B级UDC 621.882 | GB 901-88 | 代替GB901-76Double end studs(clamping type) -Product grade B－－手工焊用焊接螺柱GB 902.1-89 | 代替GB902-76Weld studs for manual welding－－机动弧焊用焊接螺柱GB 902.2-89 | 代替GB902-76Weld studs for arc welding－－储能焊用焊接螺柱GB 902.3-89 | 代替GB902-76Weld studs for capacitor discharge welding－－等长双头螺柱C级UDC 621.882 | GB 953-88 | 代替GB953-76 Double end studs(clamping type)-product grade C－－螺杆GB /T 15389-94 |Threaded rods螺母－－方螺母C级UDC 621.882.3 | GB 39-88 | 代替GB39-76 Square nuts-product grade C－－六角螺母C级ISO 4034：1999 | GB /T41-2000 | 代替GB/T 41-1986 Hexagon nuts-product grade C－－六角厚螺母ISO 621.882.3 | GB 56-88 | 代替GB56-76Hexagon thick nuts－－蝶形螺母UDC 621.882.3 | GB 62-88 | 代替GB62-76Wing nuts－－环形螺母UDC 621.882.3 | GB 63-88 | 代替GB63-76Lifting nuts－－组合式盖形螺母UDC 621.882.3 | GB 802-88 | 代替GB802-76 Acorn nuts－－球面六角螺母UDC 621.882.3 | GB 804-88 | 代替GB804-76 Hexagon nuts with raised face－－扣紧螺母UDC 621.882.3 | GB 805-88 | 代替GB805-76Tight nuts－－滚花高螺母UDC 621.882.3 | GB 806-88 | 代替GB806-76Knurled nut with collar－－滚花薄螺母UDC 621.882.3 | GB 807-88 | 代替GB807-76Knurled nuts－－小六角特扁细牙螺母UDC 621.882.3 | GB 808-88 | 代替GB808-76 Small hexagon thin nuts-Fine pitch thread－－嵌装圆螺母UDC 621.882.3 | GB 809-88 | 代替GB809-76Lnsert round nuts－－小圆螺母UDC 621.882.3 | GB 810-88 | 代替GB810-76Small round nuts－－圆螺母UDC 621.882.3 | GB 812-88 | 代替GB812-76Round nuts－－端面带孔圆螺母UDC 621.882.3 | GB 815-88 | 代替GB815-76 Round nuts with drilled holes in one face－－侧面带孔圆螺母UDC 621.882.3 | GB 816-88 | 代替GB816-79Round nuts with set pin holes in side－－带槽圆螺母UDC 621.882.3 | GB 817-88 | 代替GB817-76Slotted round nuts－－1型非金属嵌件六角锁紧螺母ISO 7040：1997 | GB /T 889.1-2000 | 代替GB/T 889-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 1－－1型非金属嵌件六角锁紧螺母细牙ISO 10512：1997 | GB /T 889.2-2000 |Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch thread－－盖形螺母UDC 621.882.3 | GB 923-88 | 代替GB923-76Acorn nuts－－1型六角螺母ISO 4032：1999 | GB /T 6170-2000 | 代替GB/T 6170-1986Hexagon nuts,style 1－－1型六角螺母细牙ISO 8673：1999 | GB /T 6171-2000 | 代替GB/T 6171-1986 Hexagon nuts,style 1,with fine pitch thread－－六角薄螺母ISO 4035：1999 | GB /T 6172.1-2000 | 代替GB/T 6172-1986Hexagon thin nuts(chamfered)－－非金属嵌件六角锁紧薄螺母ISO 10511：1997 | GB /T 6072.2-2000 |Prevailing torque type hexagon thin nuts(with non-metallic insert)－－六角薄螺母细牙ISO 8675：1999 | GB /T 6173-2000 | 代替GB/T 6173-1986 Hexagon thin nuts(chamfered) with fine pitch thread－－六角薄螺母无倒角ISO 4036：1999 | GB /T 6174-2000 | 代替GB/T 6174-1986 Hexagon thin nuts(unchamfered)－－2型六角螺母ISO 4033：1999 | GB /T 6175-2000 | 代替GB/T 6175-1986Hexagon nuts,style 2－－2型六角螺母细牙ISO 8674：1999 | GB /T 6176-2000 | 代替GB/T 6176-1986 Hexagon nuts,style 2,with fine pitch thread－－六角法兰面螺母ISO 4161：1999 | GB /T 6177.1-2000 | 代替GB/T 6177-1986 Hexagon nuts with flange－－六角法兰面螺母细牙ISO 10663：1999 | GB /T 6177.2-2000 |Hexagon nuts with flange-fine pitch thread－－1型六角开槽螺母-A和B级UDC 621.882.3 | GB 6178-86 | 代替GB57~58-76 Hexagon slotted and castle nuts,style 1 -product grades A and B－－1型六角开槽螺母-C级UDC 621.882.3 | GB 6179-86 | 代替GB57~58-76Hexagon slotted nuts,style 1 -product grade C－－2型六角开槽螺母-A和B级UDC 621.882.3 | GB 6180-86 |Hexagon slotted and castle nuts,style 2 -Product grades A and B－－六角开槽薄螺母-A和B级UDC 621.882.3 | GB 6181-86 | 代替GB59~60-76 Hexagon thin slotted nuts-Product grades A and B－－2型非金属嵌件六角锁紧螺母ISO 7041：1997 | GB /T 6182-2000 | 代替GB/T 6182-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 2－－非金属嵌件六角法兰面锁紧螺母ISO 7043：1997 | GB /T 6183.1-2000 | 代替GB/T 6183-1986Prevailing torque type hexagon nuts with flange(with non-metallic insert)－－非金属嵌件六角法兰面锁紧螺母细牙ISO 12125：1997 | GB /T 6183.2-2000 | Prevailing torque type hexagon nuts with flange(with non-metallic insert)with fine pitch thread－－1型全金属六角锁紧螺母ISO 7719：1997 | GB /T 6184-2000 | 代替GB/T 6184-1986 Prevailing torque type all-metal hexagon nuts,style 1－－2型全金属六角锁紧螺母ISO 7042：1997 | GB /T 6185.1-2000 | 代替GB/T 6185-1986 Prevailing torque type all-metal hexagon nuts,style 2－－2型全金属六角锁紧螺母细牙ISO 10513：1997 | GB /T 6185.2-2000 |Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch thread－－2型全金属六角锁紧螺母9级ISO 7720：1997 | GB /T 6186-2000 | 代替GB/T 6186-1986Prevailing torque type all-metal hexagon nuts,style 2-Property class 9－－全金属六角法兰面锁紧螺母ISO 7044：1997 | GB /T 6187.1-2000 | 代替GB/T 6187-1986Prevailing torque type all-metal hexagon nuts with flange－－全金属六角法兰面锁紧螺母细牙ISO 12126：1997 | GB /T 6187.2-2000 |Prevailing torque type all-metal hexagon nuts with flange with fine pitch thread－－1型六角开槽螺母细牙A和B级UDC 621.882.3 | GB 9457-88 | 代替GB57、58-76 Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and B－－2型六角开槽螺母细牙A和B级UDC 621.882.3 | GB 9458-88 |Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and B－－六角开槽薄螺母细牙A和B级UDC 621.882.3 | GB 9459-88 | 代替GB59、60-76 Hexagon thin slotted nuts--Fine pitch thread -Product grades A and B－－焊接方螺母GB /T 13680-92 |Square weld nuts－－焊接六角螺母GB /T 13681-92 |Hexagon weld nuts－－平头铆螺母GB /T 17880.1-1999 |Flat head riveted nuts－－沉头铆螺母GB /T 17880.2-1999 |Countersunk head riveted nuts－－小沉头铆螺母GB /T 17880.3-1999 |Small countersunk head riveted nuts－－120°小沉头铆螺母GB /T 17880.4-1999 |120°Small countersunk head riveted nuts－－平头六角铆螺母GB /T 17880.5-1999 |Flat head hexagon riveted nuts－－精密机械用六角螺母ISO 4166：1979 | GB /T 18195-2000 |Hexagon nuts for fine mechanics螺钉－－开槽圆柱头螺钉ISO 1207：1992 | GB /T 65-2000 | 代替GB/T 65-1985 Slotted cheese head screws－－开槽盘头螺钉ISO 1580：1994 | GB /T 67-2000 | 代替GB/T 67-1985Slotted pan head screws－－开槽沉头螺钉ISO 2009：1994 | GB /T 68-2000 | 代替GB/T 68-1985Slotted countersunk flat head screws (common head style)－－开槽半沉头螺钉ISO 2010：1994 | GB /T 69-2000 | 代替GB/T 69-1985 Countersunk slotted raised head screws (common head style)－－内六角圆柱头螺钉ISO 4762：1997 | GB /T 70.1-2000 | 代替GB/T 70-1985 Hexagon socket head cap screws－－内六角平圆头螺钉ISO 7380：1997 | GB /T 70.2-2000 |Hexagon socket button head screws－－内六角沉头螺钉ISO 10642：1997 | GB /T 70.3-2000 |Hexagon socket countersunk head screws－－开槽锥端紧定螺钉UDC 621.882.219 | GB 71-85 | 代替GB71-76Slotted set screws with cone point－－开槽锥端定位螺钉UDC 621.882.2 | GB 72-88 | 代替GB72-76Slotted setscrews with cone point－－开槽平端紧定螺钉UDC 621.882.219.4 | GB 73-85 | 代替GB73-76Slotted set screws with flat point－－开槽凹端紧定螺钉UDC 621.882.219.4.092.6 | GB 74-85 | 代替GB74-76Slotted set screws with cup point－－开槽长圆柱端紧定螺钉UDC 621.882.219.4.092.5 | GB 75-85 | 代替GB75-76Slotted set screws with long dog point－－内六角平端紧定螺钉ISO 4026：1993 | GB /T 77-2000 | 代替GB/T 77-1985 Hexagon socket set screws with flat point－－内六角锥端紧定螺钉ISO 4027：1993 | GB /T 78-2000 | 代替GB/T 78-1985 Hexagon socket set screws with cone point－－内六角圆柱端紧定螺钉ISO 4028：1993 | GB /T 79-2000 | 代替GB/T 79-1985 Hexagon socket set screws with dog point－－内六角凹端紧定螺钉ISO 4029：1993 | GB /T 80-2000 | 代替GB/T 80-1985 Hexagon socket set screws with cup point－－方头长圆柱球面端紧定螺钉UDC 621.882.2 | GB 83-88 | 代替GB83-76Square set screws with long dog point and rounded end－－方头凹端紧定螺钉UDC 621.882.2 | GB 84-88 | 代替GB84-76Square set screws with cup point－－方头长圆柱端紧定螺钉UDC 621.882.2 | GB 85-88 | 代替GB85-76Square set screws with long dog point－－方头短圆柱锥端紧定螺钉UDC 621.882.2 | GB 86-88 | 代替GB86-76Square set screws with short dog point and cone end－－十字槽盘头螺钉ISO 7045：1994 | GB /T 818-2000 | 代替GB/T 818-1985Pan head screws with cross recess－－十字槽沉头螺钉第1部分：钢4.8级ISO 7046-1：1994 | GB /T 819.1-2000 | 代替GB/T 819-1985Countersunk flat head screws (common head style)with cross recess-Part 1:Steel of property class 4.8－－十字槽沉头螺钉第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3ISO 7046-2：1990 | GB /T 819.2-1997 |Cross recessed countersunk flat head screws (common head style)-Grade A-Part 2:Steel of property class 8.8, stainless and non-ferrous metals－－十字槽半沉头螺钉ISO 7047：1994 | GB /T 820-2000 | 代替GB/T 820-1985 Countersunk raised head screws (common head style) with cross recess－－方头平端紧定螺钉UDC 621.882.2 | GB 821-88 | 代替GB821-76Square set screws with chamfered end－－十字槽圆柱头螺钉ISO 7048：1998 | GB /T 822-2000 | 代替GB/T 822-1988Cheese head screws with cross recess－－十字槽小盘头螺钉UDC 621.882.2 | GB 823-88 | 代替GB823-76Cross recessed small pan head screws－－吊环螺钉UDC 621.882 | GB 825-88 | 代替GB825-76Eyebolts－－开槽盘头定位螺钉UDC 621.882.2 | GB 828-88 | 代替GB828-76Slotted pan head set setscrews with dog point－－开槽圆柱端定位螺钉UDC 621.882.2 | GB 829-88 | 代替GB829-76Slotted setscrews with dog point－－开槽圆柱头轴位螺钉UDC 621.882.2 | GB 830-88 | 代替GB830-76Slotted cheese head screws with shoulder－－开槽无头轴位螺钉UDC 621.882.2 | GB 831-88 | 代替GB831-76Slotted shoulder screws－－开槽带孔球面圆柱头螺钉UDC 621.882.2 | GB 832-88 | 代替GB832-76Slotted capstan screws－－开槽大圆柱头螺钉UDC 621.882.2 | GB 833-88 | 代替GB833-76Slotted large cheese head screws－－滚花高头螺钉UDC 621.882.2 | GB 834-88 | 代替GB834-76Knurled thumb screws－－滚花平头螺钉UDC 621.882.2 | GB 835-88 | 代替GB835-76Knurled screws－－滚花小头螺钉UDC 621.882.2 | GB 836-88 | 代替GB836-76Knurled screws with small head－－开槽盘头不脱出螺钉UDC 621.882.2 | GB 837-88 | 代替GB837-76Slotted pan head screws with waisted shank－－六角头不脱出螺钉UDC 621.882.2 | GB 838-88 | 代替GB838-76Hexagon screws with waisted shank－－滚花头不脱出螺钉UDC 621.882.2 | GB 839-88 | 代替GB839-76Knurled thumb screws with waisted shank－－塑料滚花头螺钉UDC 621.882.2 | GB 840-88 | 代替GB840-79Plastic diamond knurlhead screws－－开槽球面圆柱头轴位螺钉UDC 621.882.2 | GB 946-88 | 代替GB946-76Slotted raised head with shoulder－－开槽球面大圆柱头螺钉UDC 621.882.2 | GB 947-88 | 代替GB947-76Slotted large raised cheese head screws－－开槽沉头不脱出螺钉UDC 621.882.2 | GB 948-88 | 代替GB948-76Slotted countersunk head screws with waisted shank－－开槽半沉头不脱出螺钉UDC 621.882.2 | GB 949-88 | 代替GB949-76Slotted raised countersunk head screws with waisted shank－－内六角花形盘头螺钉UDC 621.882.2 | GB 2672-86 | 代替GB2672-81Hexagon lobular socket pan head screws－－内六角花形沉头螺钉UDC 621.882.2 | GB 2673-86 | 代替GB2673-81Hexagon lobular socket countersunk head screws－－内六角花形半沉头螺钉UDC 621.882.2 | GB 2674-86 | 代替GB2674-81Hexagon lobular socket raised countersunk head screws－－内六角圆柱头轴肩螺钉UDC 621.882.215.6 | GB 5281-85 |Hexagon socket head shoulder screws－－内六角花形圆柱头螺钉-4.8级UDC 621.882.2 | GB 6190-86 | 代替GB2671-81 Hexagon lobular socket head cap screws-property class 4.8－－内六角花形圆柱头螺钉-8.8和10.9级UDC 621.882.2 | GB 6191-86 | 代替GB2671-81 Hexagon lobular socket head cap screws-property class 8.8 and 10.9－－精密机械用紧固件十字槽螺钉GB /T 13806.1-92 |Fasteners for mechanics-Cross recessed screws垫圈－－标准型弹簧垫圈UDC 621.882.4 | GB 93-87 | 代替GB93-76Single coil spring lock washers Normal type－－平垫圈C级ISO 7091：2000 | GB /T 95-2002 | 代替GB/T 95-1985Plain washers-Product grade C－－大垫圈A级ISO 7093-1：2000 | GB /T 96.1-2002 | 代替GB/T 96-1985Plain washers-Large series-Product grade A－－大垫圈C级ISO 7093-2：2000 | GB /T 96.2-2002 | 代替GB/T 96-1985Plain washers-Large series-Product grade C－－平垫圈A级ISO 7089：2000 | GB /T 97.1-2002 | 代替GB/T 97.1-1985Plain washers-Product grade A－－平垫圈倒角型A级ISO 7090：2000 | GB /T 97.2-2002 | 代替GB/T 97.2-1985Plain washers,chamfered-Product grade A－－销轴用平垫圈ISO 8738：1986 | GB /T 97.3-2000 |Plain washers for clevis pins－－平垫圈用于螺钉和垫圈组合件ISO 10673：1998 | GB /T 97.4-2002 | 代替GB/T 9074.24、9074.25-1988Plain washers for screw and washer assemblies－－平垫圈用于自攻螺钉和垫圈组合件ISO 10669：1999 | GB /T 97.5-2002 | 代替GB/T 9074.29、9074.30-1988Plain washers for tapping screw and washer assemblies－－小垫圈A级ISO 7092：2000 | GB /T 848-2002 | 代替GB/T 848-1985Plain washers-small series-Product grade A－－球面垫圈UDC 621.882.4 | GB 849-88 | 代替GB849-76Washers with ball face－－锥面垫圈UDC 621.882.4 | GB 850-88 | 代替GB850-76Washers with cone face－－开口垫圈UDC 621.882.4 | GB 851-88 | 代替GB851-76Washers with split－－工字钢用方斜垫圈UDC 621.882.4 | GB 852-88 | 代替GB852-76Square taper washers for I section－－槽钢用方斜垫圈UDC 621.882.4 | GB 853-88 | 代替GB853-76Square taper washers for slot section－－单耳止动垫圈UDC 621.882.4 | GB 854-88 | 代替GB854-76Tab washers with long tab－－双耳止动垫圈UDC 621.882.4 | GB 855-88 | 代替GB855-76Tab washers with long tab and wing－－外舌止动垫圈UDC 621.882.4 | GB 856-88 | 代替GB856-76External tab washers－－圆螺母用止动垫圈UDC 621.882.4 | GB 858-88 | 代替GB858-76Tab washers for round nut－－轻型弹簧垫圈UDC 621.882.4 | GB 859-87 | 代替GB859-76Single coil spring lock washers,Light type－－鞍形弹性垫圈UDC 621.882.4 | GB 860-87 | 代替GB860-76Curved spring washers－－内齿锁紧垫圈UDC 621.882.4 | GB 861.1-87 | 代替GB861-76Lock washers internal teeth－－内锯齿锁紧垫圈UDC 621.882.4 | GB 861.2-87 |Serrated lock washers internal teeth－－外齿锁紧垫圈UDC 621.882.4 | GB 862.1-87 | 代替GB862-76Lock washers external teeth－－外锯齿锁紧垫圈UDC 621.882.4 | GB 862.2-87 |Serrated lock washers external teeth－－波形弹性垫圈UDC 621.882.4 | GB 955-87 | 代替GB955-76Wave spring washers－－锥形锁紧垫圈UDC 621.882.4 | GB 956.1-87 | 代替GB956-76 Countersunk external toothed lock washers－－锥形锯齿锁紧垫圈UDC 621.882.4 | GB 956.2-87 |Countersunk Serrated external toothed lock washers－－特大垫圈C级ISO 7094：2000 | GB /T 5287-2002 | 代替GB/T 5287-1985 Plain washers-Extra large series-Product grade C－－重型弹簧垫圈UDC 621.882.4 | GB 7244-87 |Single coil spring lock washers,heavy type－－鞍形弹簧垫圈UDC 621.882.4 | GB 7245-87 |Curved Single coil spring lock washers－－波形弹簧垫圈UDC 621.882.4 | GB 7246-87 |Wave Single coil spring lock washers木螺钉－－开槽圆头木螺钉UDC 621.882.2 | GB 99-86 | 代替GB99-76Slotted round head wood screws－－开槽沉头木螺钉UDC 621.882.2 | GB 100-86 | 代替GB100-76Slotted countersunk head wood screws－－开槽半沉头木螺钉UDC 621.882.2 | GB 101-86 | 代替GB101-76Slotted raised countersunk head wood screws－－六角头木螺钉UDC 621.882.2 | GB 102-86 | 代替GB102-76Hexagon head wood screws－－十字槽圆头木螺钉UDC 621.882.2 | GB 950-86 | 代替GB950-76Cross recessed round head wood screws－－十字槽沉头木螺钉UDC 621.882.2 | GB 951-86 | 代替GB951-76Cross recessed countersunk head wood screws－－十字槽半沉头木螺钉UDC 621.882.2 | GB 952-86 | 代替GB952-76Cross recessed raised head countersunk head wood screws自攻螺钉－－十字槽盘头自攻螺钉UDC 621.882.216.5.082.8 | GB 845-85 | 代替GB845-76 Cross recessed pan head tapping screws－－十字槽沉头自攻螺钉UDC 621.882.216.5.082.8 | GB 846-85 | 代替GB846-76 Cross recessed countersunk head tapping screws－－十字槽半沉头自攻螺钉UDC 621.882.216.5.082.8 | GB 847-85 | 代替GB847-76 Cross recessed raised countersunk head tapping screws－－开槽盘头自攻螺钉UDC 621.882.215.082.8 | GB 5282-85 |Slotted pan head tapping screws－－开槽沉头自攻螺钉UDC 621.882.215.082.8 | GB 5283-85 |Slotted countersunkhead tapping screws－－开槽半沉头自攻螺钉UDC 621.882.215.082.8 | GB 5284-85 |Slotted raised countersunkhead tapping screws－－六角头自攻螺钉UDC 621.882.215.082.8 | GB 5285-85 |Hexagon head tapping screws－－十字槽盘头自攻锁紧螺钉UDC 621.882 | GB 6560-86 |Cross recessed pan head thread forming screws－－十字槽沉头自攻锁紧螺钉UDC 621.882 | GB 6561-86 |Cross recessed countersunk head thread forming screws－－十字槽半沉头自攻锁紧螺钉UDC 621.882 | GB 6562-86 |Cross recessed raised countersunk head thread forming screws－－六角头自攻锁紧螺钉UDC 621.882 | GB 6563-86 |Hexagon head thread forming screws－－内六角花形圆柱头自攻锁紧螺钉UDC 621.882 | GB 6564-86 |Hexagon lobular socket thread forming screws－－十字槽头凹穴六角头自攻螺钉UDC 621.882.2 | GB 9456-88 |Cross recessed hexagon head tapping screws with indentation－－精密机械用紧固件十字槽自攻螺钉刮削端GB /T 13806.2-92 |Fasteners for fine mechanics-Cross recessed tapping screws-Scrape point－－墙板自攻螺钉GB /T 14210-93 |Dry wall screws－－十字槽盘头自钻自攻螺钉ISO 15481:1999 | GB /T 15856.1-2002 | 代替GB/T 15856.1-1995Cross recessed pan head drilling screws with tapping screw thread－－十字槽沉头自钻自攻螺钉ISO 15482:1999 | GB /T 15856.2-2002 | 代替GB/T 15856.2-1995Cross recessed countersunk head drilling screws with tapping screw thread－－十字槽半沉头自钻自攻螺钉ISO 15483:1999 | GB /T 15856.3-2002 | 代替GB/T 15856.3-1995Cross recessed raised countersunk head drilling screws with tapping screw thread－－六角法兰面自钻自攻螺钉GB /T 15856.4-2002 | 代替GB/T 15856.4-1995Hexagon flange drilling screws with tapping screw thread－－六角凸缘自钻自攻螺钉ISO 15480:1999 | GB /T 15856.5-2002 |Hexagon washer head drilling screws with tapping screw thread－－六角凸缘自攻螺钉ISO 7053:1992 | GB /T 16824.1-1997 |Hexzgon head tapping screws with collar－－六角法兰面自攻螺钉ISO 10509:1992 | GB /T 16824.2-1997 |Hexagon flange head tapping screws销－－开口销ISO 1234:1997 | GB /T 91-2000 | 代替GB/T 91-1986Split pins－－圆锥销ISO 2339:1986 | GB /T 117-2000 | 代替GB/T 117-1996Taper pins－－内螺纹圆锥销ISO 8736:1986 | GB /T 118-2000 | 代替GB?T 118-1996Taper pins with internal thread－－圆柱销不淬硬钢和奥氏体不锈钢ISO 2338:1997 | GB /T 119.1-2000 | 代替GB/T 119-1986Parallel pins,of unhardened steel and austenitic stainless steel－－圆柱销淬硬钢和马氏体不锈钢ISO 8734:1997 | GB /T 119.2-2000 | 代替GB/T 119-1986Parallel pins,of hardened steel and martensitic stainless steel (Dowel pins)－－内螺纹圆柱销不淬硬钢和奥氏体不锈钢ISO 8733:1997 | GB /T 120.1-2000 | 代替GB/T 120-1986Parallel pins with internal thread, of unhardened steel and austenitic stainless steel－－内螺纹圆柱销淬硬钢和马氏体不锈钢ISO 8735:1997 | GB /T 120.2-2000 | 代替GB/T 120-1986Parallel pins with internal thread,of hardened steel and martensitic stainless steel－－开尾圆锥销UDC 621.886 | GB 877-76 | 代替GB877-76Taper pins with split－－螺纹圆柱销UDC 621.886 | GB 878-86 | 代替GB878-76Parallel pins with external thread－－弹性圆柱销直槽重型ISO 8752:1997 | GB /T 879.1-2000 | 代替GB/T 879-1986 Spring-type straight pins-Slotted, heavy duty－－弹性圆柱销直槽轻型ISO 13337:1997 | GB /T 879.2-2000 |Spring-type straight pins-Slotted,light duty－－弹性圆柱销卷制重型ISO 8748:1997 | GB /T 879.3-2000 |Spring-type straight pins-Coiled,heavy duty－－弹性圆柱销卷制标准型ISO 8750:1997 | GB /T 879.4-2000 |Spring-type straight pins-Coiled,standard duty－－弹性圆柱销卷制轻型ISO 8751:1997 | GB /T 879.5-2000 |Spring-type straight pins-Coiled,light duty－－带孔销UDC 621.886 | GB 880-86 | 代替GB880-76Pins with split pin hole－－螺尾锥销ISO 8737:1986 | GB /T 881-2000 | 代替GB/T 881-1986Taper pins with external thread－－销轴UDC 621.886 | GB 882-86 | 代替GB882-76Clevis pins with head－－槽销平行沟槽GB /T 13829.1-92 |Crooved pins-Parallel grooved－－槽销锥销GB /T 13829.2-92 |Crooved pins-taper grooved－－槽销圆头沉头GB /T 13829.3-92 |Grooved pins-with round head or countersunk head铆钉－－平头铆钉UDC 621.884 | GB 109-86 | 代替GB109-76Flat head rivets－－标牌铆钉UDC 621.884 | GB 827-86 | 代替GB827-76Rivets for name plate－－半圆头铆钉(粗制)UDC 621.884 | GB 863.1-86 | 代替GB863-76Round head rivets-Black－－小半圆头铆钉(粗制)UDC 621.884 | GB 863.2-86 |Round head rivets with small head-Black－－平锥头铆钉(粗制)UDC 621.884 | GB 864-86 | 代替GB864-76Cone head rivets-Black－－沉头铆钉(粗制)UDC 621.884 | GB 865-86 | 代替GB865-86Countersunk head rivets-Black－－半沉头铆钉(粗制)UDC 621.884 | GB 866-86 | 代替GB866-76Oval countersunk head rivets-Black－－半圆头铆钉UDC 621.884 | GB 867-86 | 代替GB867-76Round head rivets－－平锥头铆钉UDC 621.884 | GB 868-86 | 代替GB868-76Cone head rivets－－沉头铆钉UDC 621.884 | GB 869-86 | 代替GB869-76 Countersunk head rivets－－半沉头铆钉UDC 621.884 | GB 870-86 | 代替GB870-76Oval countersunk head rivets－－扁圆头铆钉UDC 621.884 | GB 871-86 | 代替GB871-76Flat round head rivets－－扁平头铆钉UDC 621.884 | GB 872-86 | 代替GB872-76Thin head rivets－－扁圆头半空心铆钉UDC 621.884 | GB 873-86 | 代替GB873-76 Oval head semi-tubular rivets－－120°沉头半空心铆钉UDC 621.884 | GB 874-86 | 代替GB874-76 120 degree countersunk head semi-tubular rivets－－扁平头半空心铆钉UDC 621.884 | GB 875-86 | 代替GB875-76 Thin head semi-tubular rivets－－空心铆钉UDC 621.884 | GB 876-86 | 代替GB876-76Tubular rivets－－120°沉头铆钉UDC 621.884 | GB 954-86 | 代替GB954-76120 degree countersunk head rivets－－管状铆钉UDC 621.884 | GB 975-86 | 代替GB975-76Pipe type rivets－－大扁圆头铆钉UDC 621.884 | GB 1011-86 | 代替GB1011-76 Truss head rivets－－120°半沉头铆钉UDC 621.884 | GB 1012-86 | 代替GB1012-76 120 degree oval countersunk rivets－－平锥头半空心铆钉UDC 621.884 | GB 1013-86 | 代替GB1013-76 Cone head semi-tubler rivets－－大扁圆头半空心铆钉UDC 621.884 | GB 1014-86 | 代替GB1014-76 Truss head semi-tublar rivets－－沉头半空心铆钉UDC 621.884 | GB 1015-86 | 代替GB1015-76 Countersunk head semi-tublar rivets－－无头铆钉UDC 621.884 | GB 1016-86 | 代替GB1016-76 Headless rivets－－封闭型扁圆头抽芯铆钉GB 12615-90 |Mushroom head break mandrel closed end blind rivets－－封闭型沉头抽芯铆钉GB 12616-90 |120 deg flush head break mandrel closed end blind rivets－－开口型沉头抽芯铆钉GB 12617-90 |120 deg flush head break mandrel blind rivets－－开口型扁圆头抽芯铆钉GB 12618-90 |Mushroom head break mandrel blind rivets－－扁圆头击芯铆钉GB /T 15855.1-1995 |Flat round head drive rivets－－沉头击芯铆钉GB /T 15855.2-1995 |Countersunk head drive rivets挡圈－－锥销锁紧挡圈UDC 621.885 | GB 883-86 | 代替GB883-76Lock rings with cone pin－－螺钉锁紧挡圈UDC 621.885 | GB 884-86 | 代替GB884-76Lock ring with screw－－带锁圈的螺钉锁紧挡圈UDC 621.885 | GB 885-86 | 代替GB885-76 Lock rings with screw and circlip－－轴肩挡圈UDC 621.885 | GB 886-86 | 代替GB886-76Rings for shoulder－－螺钉紧固轴端挡圈UDC 621.885 | GB 891-86 | 代替GB891-76Lock rings at the end of shaft with screw－－螺栓紧固轴端挡圈UDC 621.885 | GB 892-86 | 代替GB892-76Lock rings at the end of shaft with bolt－－孔用弹性挡圈-A型UDC 621.885 | GB 893.1-86 | 代替GB893-76 Circlips for holes-type A－－孔用弹性挡圈-B型UDC 621.885 | GB 893.2-86 |Circlips for hole-type B－－轴用弹性挡圈-A型UDC 621.885 | GB 894.1-86 | 代替GB894-76 Circlips for shaft-type A－－轴用弹性挡圈-B型UDC 621.885 | GB 894.2-86 |Circlips for shaft-type B－－孔用钢丝挡圈UDC 621.885 | GB 895.1-86 | 代替GB895-76 Roundwire snap rings for hole－－轴用钢丝挡圈UDC 621.885 | GB 895.2-86 | 代替GB895-76 Roundwire snap rings for shaft－－开口挡圈UDC 621.885 | GB 896-86 | 代替GB896-76“E”rings－－钢丝锁圈UDC 621.885 | GB 921-86 | 代替GB921-76Round wire circlips－－夹紧挡圈UDC 621.885 | GB 960-86 | 代替GB960-76Grip rings紧固件-组合件和连接副－－钢结构用高强度大六角头螺栓GB /T 1228-91 | 代替GB1228-84 High strength bolts with large hexagon head for steel structures－－钢结构用高强度大六角头螺母GB /T 1229-91 | 代替GB1229-84High strength large hexagon nuts for steel structures－－钢结构用高强度垫圈GB /T 1230-91 | 代替GB1230-84High strength plain washers for steel structures－－钢结构用扭剪型高强度螺栓连接副GB /T 3632-1995 | 代替GB3632-83Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures－－螺栓或螺钉和平垫圈组合件ISO 10644：1998 | GB /T 9074.1-2002 | 代替GB/T 9074.1、9074.14-1988Bolt or screw and washer assemblies with plain washers－－十字槽头螺钉和外锯齿锁紧垫圈组合件UDC 621.882 | GB 9074.2-88 |Cross recessed pan head screw and serrated lock washer external teeth assemblies－－十字槽盘头螺钉和弹簧垫圈组合件UDC 621.882 | GB 9074.3-88 |Cross recessed pan head screw and single coll spring lock washer assemblies－－十字槽盘头螺钉、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.4-88 |Cross recessed pan head screw, single coil spring lock washer assemblies－－十字槽小盘头螺钉和平垫圈组合件UDC 621.882 | GB 9074.5-88 |Cross recessed small pan head screw and small plain washer assemblies－－十字槽小盘头螺钉和大垫圈组合件UDC 621.882 | GB 9074.6-88 |Cross recessed small pan head screw and big plain washer assemblies－－十字槽小盘头螺钉和弹簧垫圈组合件UDC 621.882 | GB 9074.7-88 |Cross recessed small pan head screw and single coil spring lock washer assemblies－－十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.8-88 |Cross recessed small pan head screw, single coil spring lock washer and plain washer assemblies －－十字槽沉头螺钉和锥形锁紧垫圈组合件UDC 621.882 | GB 9074.9-88 |Cross recessed countersunk head screw and countersunk serrated external toothed lock washer assemblies－－十字槽半沉头螺钉和锥形锁紧垫圈组合件UDC 621.882 | GB 9074.10-88 |Cross recessed raised countersunk head screw and countersunk external toothed lock washer assemblies－－十字槽凹穴六角头螺栓和平垫圈组合件UDC 621.882 | GB 9074.11-88 |Cross recessed hexagon bolt with indentation and plain washer assemblies－－十字槽凹穴六角头螺栓和弹簧垫圈组合件UDC 621.882 | GB 9074.12-88 |Cross recessed hexagon bolt with indetation single coil spring lock washer assemblies－－十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.13-88 | Cross recessed hexagon bolt with indetation,single coil lock washer and plain washer assemblies －－六角头螺栓和弹簧垫圈组合件UDC 621.882 | GB 9074.15-88 |Hexagon head bolt and single coil spring lock washer assemblies－－六角头螺栓和外锯齿锁紧垫圈组合件UDC 621.882 | GB 9074.16-88 |Hexagon head bolt and serrated lock washer external teeth assemblies－－六角头螺栓、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.17-88 |Hexagon head bolt,single coil spring lock washer and plain washer assemblies－－自攻螺钉和平垫圈组合件ISO 10510：1999 | GB /T 9074.18-2002 | 代替GB/T 9074.18、9074.19、9074、22、9074、23-1988Tapping screw and washer assemblies with plain washers－－十字槽凹穴六角头自攻螺钉和平垫圈组合件UDC 621.882 | GB 9074.20-88 |Cross recessed hexagon head tapping screw with indentation and plain washer assemblies－－十字槽凹穴六角头自攻螺钉和大垫圈组合件UDC 621.882 | GB 9074.21-88 |Cross recessed hexagon head tapping sorew with indentation and large plain washer assemblies。
紧固件-中英文对照.doc
紧固件-中英文对照.docNo.xx 简写中文1screw scr螺丝2nut nut 螺母3washer wash垫圈4head hd 头5thread thre 螺纹6coating coat 镀层7rivet riv 铆钉8standoff stdoff 内外六角钉9driver driv 穴10hexagon hexa六角11tooth tooth 齿12lock lck 锁13spring spr 弹簧14wave wave 波浪型15pitch pitch 牙距16partial thread PT 半螺纹17PT PT一种螺纹形式18Full Thread FT全螺纹19silver silv 银20cone cone锥形21 Eco-syn Eco 30度牙的一种螺纹22 ThreadForming TF自攻螺纹23 Self Tapping self tapp自切屑螺纹24 pin pin 销25shaft Shaf轴26steel St铁27stainless steel SS不锈钢28Brass(Cu) Bras(Cu)铜29Aluminum AL 铝30Rubber Rub橡胶31machine screw mech scr机制螺丝32SEM screw SEM Scr组合螺丝33Material material 材料34Grade GD等级35Finish Finish表面处理36Point Point 点37Clamp Clam夹子38internal Int 内39external ext 外40thickness /厚度41length /xx42 hole /xx43 Metric Metcric 公制44 DIN /德标45 ANSI /美标46 JIS /日标螺丝相关参数英语对照A:Machine Screw:机械螺丝B:Tapping Screw:自攻螺丝 (分使用于金属与使用于塑料二种 ) B-1: Sheet Metal Tapping Screw. 铁(板牙自攻螺丝 )B-2: Plastic Tapping Screw.塑(料用 ,自攻螺丝 )C:Wooden Screw 木:工螺丝D:Drywall Screw :水泥墙螺丝常见螺丝材质 :a.Low Carbon Steel 低:碳钢b. SS-304 : Stainless Steel 304c.SS-302: Stainless Steel 302结:构韧性较好d.Aluminum 5052 :铝合金 5052d.Brass:xxe.Bronze:青铜f.UNS C11000 Copper:锑铜Finish Code:外观处理规格Head Code:头部外型螺丝型号 Drive Code:头部剖沟 ,特征型号Length Code:螺丝长度(mm)A-1: Thread Code:螺丝型号A-2: Length Code:螺丝长度 :A-3: Drive Code/头部剖沟 ,特征 .a. Slotted:一字 ( Minus )b. Phillips:十字 ( Plus )c.Phil-Slot:一字 / 十字d.Hex Scoket:xxe.One Way:单向 (只可锁入 ,不可退出 ) A-4: Head Code/头部外型 .a. Flat:平头 (锁入后 ,顶部与工作件齐平 )b.Oval:色拉头c.Round:圆头d.Pan:圆扁头e.Truss:大圆扁头f.Hex :六角头A-5: Finish Code/外观处理 .a. Z: Zine-Plated:镀锌b. Ni: Ni-Plated:镀镍c.Tin-Plated:镀锡d.Zine Plated / Green Iridite:镀锌绿膜处理 .e.Radiant Plated:镀五彩f.Passivate:抗氧化处理 .g.Alodial Finish:无外观处理螺纹大径： Major Diam螺纹中径： Pitch diam螺纹底径： Minor diam通止规： Go/No go gage机械性能： mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆 Case carburization表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinellxx 氏硬度Metallography microscope 金相显微镜Salt spray device盐雾试验箱Tensile testing machine拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8机械性能 8 级原材料： Raw material 球化退火： Annealing冷拔： Drawingxx：Forming机加工： Machining螺纹成型： Roll Threading热处理： heat-treatment表面处理： finish去氢： Lustrating hydrogen检验： Inspection包装： Packing入库： Stocking车床： lathe磨制： grinding红打： hot forging冲压： punchingDiameter 直径Lengthxx各类紧固件标准件产品xx 对照插片壁虎 Steel Ceiling Anchors内迫壁虎 Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力 xx 壁虎 Wedge Anchors外迫壁虎 Cut Anchors化学壁虎 Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽 Strut Nuts兰花夹系列 T oggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎 Sleeve Anchors打入式壁虎鱼形尼龙壁虎 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎 Hit Anchors电梯壁虎 Bolt Anchors重载壁虎 Heavy duty anchors两片夹 Loxin Masonry Anchors定位螺栓 Set Bolts长型兰花夹 Short Strap Anchors工具棒 Drop in Setting Tools象脚壁虎 Elephant foot anchors水泥预埋件 Concrete Insert翻边胀轴 Drop in Anchor with Lip冲件 Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽 Hex Coupling Nuts(High Nuts) 圆螺帽 Round Nuts 四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU 形螺帽 U NutsT 形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽 Weld Nuts高张力螺帽 Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽 Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽 Anchor Nuts大尺寸螺帽 Big Size Nuts铁盖袋帽 Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖 +尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽 Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts 不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽 Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝 (栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角 xx 螺丝 Hex Lag Bolts四角螺丝 Square Head BoltsT 头螺丝 T Head Bolts环首螺丝 Eye Bolts内六角孔螺丝Hex Socket Cap Screws 固定螺丝 Set Screws螺椿栓 Stud Bolts螺旋椿 Screw Studs轮壳螺栓 Wheel Bolts翼形螺丝 Wing Screws自攻螺丝 Self Tapping Screws自削螺丝 Thread Cutting Screws钻尾螺丝 Self Drilling Screws旋入螺丝 Drive Screws机械螺丝 Machine Screws木螺丝 Wood Screws家具螺丝 Furniture Screws塑板螺丝 Chipboard Screws墙用螺丝 Drywall Screws基础螺栓 Foundation BoltsU 型螺栓 U Bolts勾头螺栓 Hook Bolts套挂螺丝 Toggle Bolts轨道螺栓 (鱼尾螺丝 ) Track Bolts耐候钢螺丝 Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓 High Strength Bolts剪力钉 (焊接螺丝 ) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems) 大尺寸螺栓 Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝 Brass Screws铝螺丝 Aluminum Screws合金钢螺丝 Alloy Steel Screws电子螺丝 Electronic Screws微小精密螺丝Micro Screws塑料螺丝 Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝 Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝 Thumb Screws双头牙螺丝 Double End Screws Hanger Bolt车辆 (汽车 )螺丝、螺帽 Automotive Fasteners航天用螺丝 Aerospace Fasteners飞机特殊扣件Source Control BoltsxxBlind Bolts面板螺丝 Panel Fasteners电梯螺丝 Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝 One Way Lag Screws管夹螺丝 Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝 Hinge Screws货柜螺丝 Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝 Trilobular Thread Screws高低牙螺丝 High Low Screws夹板用螺丝 Particle Board Screws马桶螺丝 Toilet Closet Bolts特长螺丝 Special Longer Screws建业螺丝 Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝 Collated Screws水泥螺丝 Concrete Screws板模螺丝 Construction Bolts锌蝶螺丝 Die Cast Wing Screws; Zinc Alloy重型车螺丝 Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws 犁壁螺丝 Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝T oggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts 六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽 Hex Coupling Nuts(High Nuts)圆螺帽 Round Nuts四角螺帽 Square Nuts管用螺帽 Pipe Nuts轮壳螺帽 Wheel Nuts蝶型螺帽 Wing NutsU 形螺帽 U NutsT 形螺帽 T Nuts环首螺帽 Eye Nuts齿形螺帽 Kep Nuts齿花螺帽 Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts 焊接螺帽 Weld Nuts高张力螺帽 Heigh Strength Nuts建业用螺帽 Structural Nuts不锈钢螺帽 Stainless Steel Nuts铜螺帽 Brass Nuts铝螺帽 Aluminum Nuts合金钢螺帽 Alloy Steel Nuts重型车螺帽 Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽 Anchor Nuts大尺寸螺帽 Big Size Nuts铁盖袋帽 Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖 +尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽 Self-Locking Nuts制止螺帽 Sliding NutsSln-自动防松螺帽 Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽 Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts 不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽 Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽 Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材 Annealing Wire And Rod黑铁丝 Black Wire黄铜棒线 Brass Wire And Rod磨光棒钢 Bright Steel Bar(Hex/Round/Square)铜合金线 Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材 Iron Or Steel Wire线材盘元 Iron Or Steel Wire Rod洋白铜线 Nickel Silver Wire磷青铜线 Phosphate Bronze Wire不锈钢条棒 Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线 (抽线后 ) Stainless Steel Draw Wire不锈钢线材 Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢 Steel Bar(Hex/Round/Square)转回 90 度碾线头机 90 讧 evolving Wire Twisting Machine 气动拉钉机 Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机 Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机 Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模 Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine 十字冲模 Header Punches In Various Drives成型冲模 Header Punches In Various Drives螺丝打头机 Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机 Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌 Mechanical Galvanized迷你成型机 Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模 Nut Forming Dies螺帽成型模 Nuts Formers特殊零件成型机Parts Forming Maching冲模 Punch Dies冲子 Punch Pins罗拉成型机 Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine 止付螺丝成型机Set Screws Formers 套高成型机 Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace 球状化热处理炉Spheroidizing Heat Treatment Furnace。
紧固件 中英文对照
No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种) B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出)A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd 电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage 螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers 螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings 汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle 针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
DIN435 DIN436 DIN438 DIN439 DIN439 DIN440 DIN443 DIN444 DIN462 DIN463 DIN464 DIN465 DIN466 DIN467 DIN470 DIN471 DIN472 DIN478 DIN479 DIN480 DIN508 DIN525 DIN529 DIN546 DIN547 DIN551 DIN553 DIN555 DIN557 DIN558 DIN561
65
DIN562
66 67 68 69
DIN571 DIN580 DIN582 DIN601
六角头木螺钉 吊环螺钉 吊环螺母 六角头螺栓
70 71
DIN603 DIN604
大半圆头方颈螺栓（马车螺 栓） 沉头带插销马车 螺栓 沉头长方颈马车 螺栓 半圆头带插销马车螺栓 沉头短方颈马车 螺栓 六角头精配螺栓 （长螺纹） 六角头精配螺栓 （短螺栓） 滚花平头螺钉 半圆头铆钉 沉头铆钉 半 沉头铆钉 大扁头铆钉 重型侧面带孔圆螺母 侧面带孔圆螺母 卡头 T 型槽螺钉 双头螺柱 （牙长 =2D ） 内六角锥型闭锁 螺钉 内六角直型闭锁 螺钉 外六角锥型闭锁 螺钉 外六角直型闭锁 螺钉 内六角扳手 内六角圆柱头螺钉 内六角平端紧定 螺钉 内六角尖端紧定 螺钉 内六角圆柱端紧定螺钉 内六角凹端紧定螺钉 薄型盲螺母 开槽小圆柱头螺钉 开槽大圆柱头螺钉
方斜垫圈（ I 型） 方垫圈 开槽凹端紧定螺钉 六角薄螺母 细牙六角薄螺母 木螺钉专用垫圈 密封帽 活节螺栓 B 型 内舌止动垫圈 双耳止动垫圈 滚花高头螺钉 开槽滚花高头螺钉 滚花高螺母 滚花薄螺母 锁紧垫圈 轴用弹性垫圈 孔用弹性垫圈 方头带垫螺栓 方头圆柱底端螺栓 方头带垫关圆底端 螺栓 T 型槽螺母 单头螺柱 地脚螺栓 带槽圆螺母 端面带孔圆螺母 开槽平端紧定螺钉 开槽锥端紧定螺钉 六角螺母 方螺母 -C 六角头螺钉 六角头圆柱端 紧定螺钉 薄型方螺母 -B
94 95 96 97 98 99
DIN914 DIN915 DIN916 DIN917 DIN920 DIN921
Hexagon socket set screws with cone point Hexagon socket set screws with dog point Hexagon socket set screws with cup point Hexagon cap nuts Slotted short cheese head screws Slotted large cheese head screws
75
DIN609
Hexagon fitted bolts,long thread
76 77 78 79 80 81 82 83 84 85 86
DIN610 DIN653 DIN660 DIN661 DIN662 DIN674 DIN703 DIN705 DIN741 DIN787 DIN835
Hexagon fitted bolts short thread Knurled thumb screws thin type Round head rivets Contersunk head rivets Raised contersunk head rivets Mushroom head rivets Adjusting rings,heavy range(shafting collars) Adjusting rings,light range(shafting collars) Wire rope clips T-slot screws Studs-metal(end=2d)
87
DIN906
Hexagon socket pipe plugs,conical thread
88
DIN908
Thread
89
DIN909
Thread
90 91 92 93
DIN910 DIN911 DIN912 DIN913
Hexagon head screw plugs,cyl.thread Socket wrenches Hexagon socket cap screws Hexagon socket set screws with falt point
100 101 102 103 104
DIN923 DIN927 DIN928 DIN929 DIN931
开槽圆柱头轴肩 螺钉 开槽无头轴肩螺钉 焊接方螺母 焊接六角螺母 六角头螺栓 （半牙） 六角头螺栓 （全牙） 六角头螺母（ 1 型） 细牙六角头螺母（ 1 型） 开槽六角螺母 六角头薄螺母 六角头开槽薄螺母 双头螺距 （牙长 =1D ） 双头螺距 （牙长 =1.5D ） 双头螺距 （牙长 =1.25D ） 六角头细牙螺栓 （全牙） 六角头细牙螺栓 （半牙） 头部穿孔六角头 螺栓 开槽沉头螺钉 开槽半沉头螺钉 十字槽沉头螺钉
33
DIN434
33
DIN434
方斜垫圈（ U 型）
U-section Square taper washers for I-sections Square washers Slotted set with cup point Hexagon thin nuts Hexagon thin nuts Rounds washers for wood constructions Sealing caps,push-in type Eye bolts form B Internal tab washers Washers with two taps Knurled thumb screws with collar Slotted knurled thumb screws with collar Knurled thumb nuts with collar Knurled thumb thin nuts Sealing washers Retaining rings for shafts(external),circlips Retaining rings for bores(internal),circlips Square head bolts with collar Square head bolts with half dog point Square head bolts with collar,half dog point T-slot nuts Single end studs Masonry bolts Slotted round nuts Round nuts with drilled holes in one face Slotted set screws with flat point Slotted set screws with cone point Hexagon nuts Square nuts Hexagon screws Hexagon set screws with full dog point Square nuts without bevel (pressed nuts) Hexgon head wood screw (coach screws) Lifting eye bolts Lifting eye nuts Hexagon blots
英文品名 Description in English Taper pins Parallel pins Slotted cheese head screws Slotted pan head screws Tab washers Split cooter pins Slotted raised csk head wood screws Slotted round head wood screws Slotted countersunk head wood screws Plain washers Mediun washers Plain washers Spring lock washers,tang ends Spring lock washers,square ends Single coil spring lock washers Curved spring washers Wave spring washers T-head blots with square neck T-head bolts with double nip Taper pins with threaded end T-head bolts Wing nuts America form Wing nuts germany form Wing screws America form Wing screws germany form Ball knobs Slotted capstan screws
中文品名 Description in Chinese 圆锥销 圆柱销 开槽圆柱头螺钉 开槽盘头螺钉 单耳止动垫圈 开口销 开槽半沉头木螺钉 开槽半圆头木螺钉 开槽沉头木螺钉 平垫 平垫（带倒角） 平垫 重型弹垫 标准弹垫 鞍形弹垫 弹簧止动垫圈 波形弹垫 T 型方颈螺栓 T 型双接头螺栓 螺纹圆锥销 T 型头螺栓 蝶型螺母（美制） 蝶型螺母（德制） 蝶型螺母（美制） 蝶型螺母（德制） 圆球型盖型螺母 开槽带孔球面 圆柱头蚴钉 开槽长圆柱端 紧定螺钉 开槽平端 紧定螺钉（半牙） 小六角特薄细牙 螺母 外舌止动垫圈 小垫圈 (用于圆柱头螺钉) 方斜垫圈（ U 型）
28
DIN417
Slotted set srews with full dog point
29
DIN427
Slotted set srews with chamfered end
30 31 32
ห้องสมุดไป่ตู้DIN431 DIN432 DIN433