船舶英文小结
船舶英语词汇
船舶英语词汇dugout 独木舟barge 驳船kayak （爱斯基摩人的）木排outrigger 桨叉架船rowing boat 划艇（美作：rowboat）gondola （意大利的）长平底船whale mother ship 捕鲸母船hydrofoil 水翼船catamarans 双体船dredger 挖泥船boat 船brig, brigantine 双桅船canoe 小船，独木舟caravel 快帆船cargo boat 货船coaster 近海贸易货船cod-fishing boat 捕鳕鱼船whaler 捕鲸船collier 运煤船battleship 战船shallop 小型战船coastguard cutter, coastguard vessel 巡逻艇，缉私艇revenue cutter 缉私船patrol boat 巡逻艇minelayer 布雷艇minesweeper 扫雷艇torpedo boat 鱼雷艇frigate 轻护航舰gunboat 炮舰submarine 潜水艇destroyer 驱逐舰corvette 轻巡洋舰cruiser 巡洋舰aircraft carrier 航空母舰ferry, ferryboat 渡船，渡轮fishing boat 渔船freighter 货船galleon 大型帆船galley 大划桨船hovercraft 气垫船icebreaker 破冰船launch 艇lifeboat 救生艇lighter 驳船liner, ocean liner 远洋班轮merchant ship, merchantman 商船motorboat 摩托艇outboard 尾部装有马达的小艇paddle steamer, paddle boat 明轮船passenger boat 客船piragua, pirogue 独木舟raft 木筏rowing boat 划艇sailing boat, sailing ship 帆船schooner 纵帆船ship 船skiff 小艇sloop 单桅船steamer, steamship 汽轮tanker 油轮trawler 拖网渔船tug, tugboat 拖轮vessel 船yacht 游艇yawl 船载小艇构架结构 Framed structure清洁压载舱Clean ballast tank纵桁结构 Girder structure冷凝水柜Condensate catch tank人孔 manhole干舱 Dry tank饮用水舱 Drinking water tank密封圈 Sealing ring污水舱 Bilge tank铰链 Hinge应急淡水柜Emergency fresh water tank 把手 Handle首舱 Fore tank平衡块 Balance block首尖舱 Fore peak tank斜边舱Hopper side tankwelding焊接液舱 Liquid tank坡口 groove龙骨舱 Keel tank单面坡口 Single groove右舷舱 Starboard tank双面坡口 Double groove顶边水舱 Topside tankⅠ形坡口 Square groove顶边翼舱Topside wing tankV型坡口Single v groove小舱口盖Small hatch coverU型坡口Single u groove水密舱口盖Water-tight small hatch coverX形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK形坡口 Single bevel grooveY形坡口Single v groove with broad rood face填充金属 Filler metal坡口面 Groove face热影响区 Heat-affected zone(HAZ)坡口角度 Groove angle过热区 Overheated zone焊缝倾角 Weld slope焊合线 Bond line(fusion line)接头根部 Root of joint焊接区 Weld zone根部间隙 Root gap焊缝区Weld metal area钝边 Root face焊缝 weld焊接接头 Welding joint连续焊缝 Continuous weld对接接头 Butt joint断续焊缝 Intermittent weld角接接头 Corner joint纵向焊缝 Longitudinal weldT形接头 T-joint横向焊缝 Transverse weld搭接接头 Lap joint对接焊缝隙 Butt weld十字接头Cross shaped joint角焊缝 Filled weld母材 Base metal(parent metal)并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器 Arc welding rectifier焊缝正面 Face of weld自动焊 Automatic welding焊缝背面 Back of weld埋弧自动焊Submerged arc welding焊缝宽度 Weld width半自动焊Semi- automatic welding焊缝长度 Weld length氩弧焊 Argon-arc welding焊缝余高 Reinforcement二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld)氧乙炔焊 Oxy-acetylene welding焊脚长度 Leg length气割 Gas cutting套管接头 Muff joint碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割 Underwater cutting直流电弧焊Direct current arc welding等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊 Continuous welding弧焊变压器 Arc welding transformer断续焊 Intermittent welding点焊 Sport welding对接焊 Butt welding分段退焊Back step welding角焊 Fillet welding分段多层焊 Block welding搭接焊 Lap welding深溶焊 Deep penetrating welding返修焊 Re-welding跳焊 Skip welding补焊 Repair welding陶质衬垫焊Ceramic backing welding定位焊 Tack welding引弧 Striking the arc封底焊Back sealing welding焊接工艺参数 Welding condition打底焊 Backing welding焊接电流 Welding current堆焊 Surfacing(overlaying)焊接电压 Welding voltage塞焊 Plug welding焊接速度 Welding speed槽焊 Slot welding电弧电压 Arc voltage盖面焊 Consmetic welding焊丝间距 Wire spacing前倾焊 Forward welding空载电压Open circuit voltage后倾焊 Backward welding熔化速度 Melting rate41． 300吨，是船台用起重机，跨度72m。
船舶专业英语(课文+翻译)
Chapter 1 Ship Design（船舶设计）Lesson 2 Ships Categorized（船舶分类）2.1 Introduction（介绍）The forms a ship can take are innumerable. 一艘船能采用的外形是不可胜数的A vessel might appear to be a sleek seagoing hotel carrying passengers along to some exotic destination; a floating fortress bristling with missile launchers; 。
or an elongated box transporting tanks of crude oil and topped with complex pipe connections. 一艘船可以看做是将乘客一直运送到外国目的地的优美的远航宾馆。
竖立有导弹发射架的水面堡垒及甲板上铺盖有复杂管系的加长罐装原油运输轮None of these descriptions of external appearance, however, does justice to the ship system as a whole and integrated unit所有这些外部特点的描述都不能说明船舶系统是一个总的集合体self-sufficient,seaworthy, and adequately stable in its function as a secure habitat for crew and cargo. ——船员和货物的安全性功能：自给自足，适航，足够稳定。
This is the concept that the naval architect keeps in mind when designing the ship and that provides the basis for subsequent discussions, not only in this chapter but throughout the entire book.这是一个造船工程师设计船舶使必须记住的、能为以后讨论提供根据的观念，不仅涉及本章也贯穿全书。
船舶专业英语
船舶类型词汇渔业船舶种类2.1 渔船fishing vessel用于商业性捕捉鱼类、鲸、海豹、海象或其他生物资源的船舶之统称。
2.1.1 拖网渔船trawler从事拖网作业，捕捞中、下层水域鱼虾类的专用渔船。
分双拖和单拖渔船，舷拖、尾拖和桁拖渔船。
2.1.1.1 双拖渔船two boat trawler，pair trawler，bull trawler由两船拖曳一顶网具进行捕捞作业的渔船。
2.1.1.2 单拖渔船single boat trawler由单船拖曳网具进行捕捞作业的渔船。
按作业方式可分为舷拖、尾拖和桁拖渔船。
2.1.1.3 舷拖渔船side trawler在船的一舷设有网板架，并进行拖网作业的渔船。
2.1.1.4 尾拖渔船stern trawler在船尾部进行拖网作业的渔船，称尾拖渔船。
单船尾拖设有网板架。
在尾部设起、放网滑道的称尾滑道拖网渔船（stern ramp trawler）。
2.1.1.5 桁拖渔船beam trawler有桁架伸于舷外，以拖曳网具进行捕捞作业的渔船。
2.1.1.6 加工拖网渔船factory trawler具有较大的冻结和加工能力的大型尾滑道拖网渔船。
2.1.2 围网渔船seiner从事围网作业，主要围捕中、上层水域鱼类的专用渔船。
包括双船及单船、舷侧起网及尾部起网灯光诱鱼、金枪鱼等围网渔船。
2.1.2.1 双船围网渔船two boat seiner由两船共放、起一顶围网进行捕捞作业的渔船。
2.1.2.2 单船围网渔船single boat seiner配有辅助船艇，单船放起围网进行捕捞作业的渔船。
2.1.2.3 灯光诱鱼围网船组light luring seiner group由一艘围网渔船，数艘诱鱼灯船以及保鲜运输船等组成的灯光诱鱼围网作业船组。
a.灯光诱鱼围网船light luring seiner利用水上及水下灯光诱集鱼群，进行围捕作业的渔船。
b.围网探鱼船fish scautang boat灯光诱鱼围网船组中，配有多种探鱼仪器设备，主要用于探测鱼群的一种小型船舶。
船舶英文小结
船舶英文词汇对照表甲板部分Rank 船员职务rank of ship’s crewCrew 船员seaman、mariner、sailor船员职务（Senior officer 高级船员）Captain 船长，（CAPT）master 船长是全船最高领导者，总管全船所有事物，拥有最高权限。
Chief officer 大副，（C/O）船舶二把手，职务仅次于船长在船长无法行驶职能时接替船长位置。
Second officer 二副（2/O）Third officer 三副（3/O）Assistant officer 驾助、驾驶助理、舵长Chief engineer 轮机长、老轨、大车（C/E）船舶机舱部主要负责人、船舶三把手Second engineer 大管轮、二轨、二车（2/E）Third engineer 二管轮、三轨、三车（3/E）Fourth engineer 三管轮、四轨、四车（4/E）Electric engineer 电机员（E/E）Assistant engineer 轮机助理、轮助普通船员Cadet 实习生、卡带DECK CADET 甲板实习生、ENGINE CADET轮机实习生Bosun 水手长（BSN）Fitter ，Carpenter 木匠（FTR）Able seaman （A.B）全能水手，一水Ordinary seaman （OS）普通水手、二水NO.1 Motorman 机工长Motorman 机工（M/M）Oiler 加油工（OIL）Wiper 抹油工（WIP）Chief cook 大厨（cook）Waiter 、Steward 服务员，大台（STDW）船舶靠港登轮人员Pilot 引航员，领航员，锚地引领员Agency ，Agent 代理，船舶代理。
简称：船代Watch man 梯口值班人员（船舶驾驶人员兼职）：船舶靠港后，海事局要求在船舶上下船处设立签到值班台，等级上下船舶人员名字，职务，来船目的，上下船时间等，并发放登轮许可证。
船舶机舱英文作文
船舶机舱英文作文英文：As a marine engineer, I have spent a lot of time in the engine room of ships. The engine room is the heart of the ship, where all the machinery and equipment are located. It is a complex and challenging environment that requires alot of knowledge and skills to operate.One of the most important pieces of equipment in the engine room is the main engine. This is the engine that powers the ship and allows it to move through the water. It is a massive piece of machinery that requires constant monitoring and maintenance to ensure it runs smoothly.Another important piece of equipment in the engine room is the generator. This is the engine that provides electricity to the ship. Without it, the ship would be unable to power its lights, navigation equipment, and other essential systems.In addition to these main pieces of equipment, there are many other systems and components that make up the engine room. These include pumps, valves, heat exchangers, and cooling systems. Each of these components plays a crucial role in keeping the ship running smoothly.As a marine engineer, I have faced many challenges in the engine room. One of the most difficult is dealing with breakdowns and malfunctions. When something goes wrong, it is important to stay calm and work quickly to diagnose and fix the problem.Overall, working in the engine room is a challenging but rewarding experience. It requires a lot of knowledge and skill, but it is also a fascinating and exciting environment to work in.中文：作为一名船舶机务工程师，我在船舶机舱里度过了很多时间。
船舶常用英语(一)解析
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶专业英文词汇汇总
船舶专业英文词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical ath Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。
船舶常用英语(一)
船舶常用英语(一)一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipVLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighteraboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framingsystem 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member 构件structural strength结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语第 31 页共 45 页angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;第 32 页共 45 页list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim第 33 页共 45 页纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)第 34 页共 45 页失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未第 35 页共 45 页装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷第 36 页共 45 页10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕第 37 页共 45 页9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油第 38 页共 45 页漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked第 39 页共 45 页阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大第 40 页共 45 页16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)电弧mutator第 41 页共 45 页整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干A. Remove, crop etc.1.Removed第 42 页共 45 页拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮2.fitted & ground拂磨第 43 页共 45 页3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance第 44 页共 45 页校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊8 tackweld 点焊、平头焊、定位焊第 45 页共 45 页。
船舶专业英文词汇汇总
船舶专业英文词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical ath Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。
船舶英语
一．名词部分（一）船舶1．船舶与海上设施的类型Type of Ship and Offshore Unit货船Cargo Ship杂货船ι General cargo ship干货船Dry cargo shipι散货船ι Bulk carrier矿沙船Ore carrierι运煤船Coalι carrier集装箱船Container shipι滚装货船Ro/Roι ship冷藏船Refrigerated shipι运畜船Cattleι carrier运木船Timber carrierι近海ι供应船Offshore supply ship散装矿砂船Bulk Ore carrierι混装船ιCombination carrier载驳母船Barge Carrierι汽车运输船ιCar carrier液货船Liquid Cargo Carrier油船Oilι tanker化学品液货船Chemical tankerι液化气体船Liquefied gasι carrier油矿两用船Oil/ore carrierι油散两用船Oil/bulkι carrier油散矿三用船Oil/bulk/ore carrierι客船Passenger Ship客船ιPassenger ship豪华旅游客船Cruise shipι旅游船ιTourist ship高速客船High speed passenger craftι双体客船ιPassenger catamaran客货船Passenger-cargo shipι客箱船ιPassenger container ship客滚船Ro/Ro Passengerι Ship高速船High Speed Craft全垫升气垫船Air-cushion Vehicleι水面效应船ιSurface Effect Ship双体气垫船Air-cushionι Catamaran侧壁气垫船Side-wall Hovercraftι高速双体船Highι Speed Catamaran高速单体船High Speed Monohull Craftι地效翼船ι Wing-in Ground Craft水翼船Hydrofoil Craftι动力支承船ι Dynamically Supported Craft两栖船Amphibious Craftι小水面单体船ιSmall Waterplane Area Single Hull Ship 小水面双体船Small Waterplaneι Area Twin Hull Ship 驳船Barge客驳Passenger Bargeι货驳ιCargo Barge敞口驳Open Bargeι甲板驳ι Deck Barge集装箱驳Container Bargeι分节驳Integratedι Barge开底驳Hopper Bargeι油驳Oilι Barge趸船（箱形驳）Pontoonι拖船Tug港作拖船Harbourι Tug打捞拖船Salvage Tugι顶推船Pusherι近海供应拖船ιOffshore tug/supply ship工程船Engineering Ship挖泥船ι Dredger耙吸式挖泥船Trailing suction dredger绞吸式挖泥船Cutter suction dredger链斗式挖泥船Bucket dredger抓斗式挖泥船Grab dredger铲斗式挖泥船Dipper dredger吹泥船Reclamation craft开底泥驳Hopper Barge对开泥驳Split Hopper Barge起重船Floating Craneι浮船坞Floatingι Dock打桩船Floating Pile Driverι布缆船Cableι Layer潜水工作船Diving Boatι港区工作船Harbour Operating Ship破冰船ιIce breaker消防船Fire Boatι救护船/救助船Rescueι Ship引水船Pilot Vesselι海关船Customsι Boat巡逻船Patrol Boatι布标船Buoy Layerι灯标船ιBeacon Boat交通艇Traffic Boatι垃圾船ι Garbage Boat浮油回收船Oil Recovery Shipι污水处理船Sewageι Disposal Vessel海水淡化船Distilling Shipι渡船Ferry乘客渡船ιPassenger Ferry火车渡船Train Ferryι车客渡船Vehicleι Passenger Ferry海峡渡船Channel Ferryι渔船Fishing Vessel渔品ι加工船Fish-Factory Ship拖网渔船Trawlerι围网渔船ι Netter捕鲸船Whaling Shipι活鱼运输船Live Fishι Carrier其他船舶科学调查船Research shipι训练船Trainingι Ship特殊用途船Special purpose shipι内河船Inlandι Waterways Ship海上设施海上移动平台Mobile Offshore Unitι海上移动钻井平台ι Mobile Offshore Drilling Unit水面式平台Surface Unitι船式平台Ship-type Unit驳船平台Barge-type Unit自升式平台ι Self-elevating Unit柱稳式平台Column-stabilized Unitι半潜式平台Semi-submersible Unit坐底式平台Submersible Unit采油平台ι Production Unit储油平台Storage Unitι生活平台ι Accommodation Unit修理平台Repair Unitι海上固定平台Fixedι Offshore Platform海底管道Submarine Pipelineι潜水系统和潜水器Divingι System and Submersible单点系泊Single Point Mooringι (SPM)浮式生产与储油装置Floating Production and Storage Unitι (FSUs)浮式生产、储存及卸载系统Floating Production, Storage and Offloading Systemι (FPSOs)2．数据与资料Data and Information数据总长Length overall(LOA)垂线间长Length bet. perpendiculars (LBP)首、尾垂线Forward and after perpendiculars型宽Moulded breadth型深Moulded depth建造日期Date of build签订建造合同日期Date of building contract龙骨安放日期Date of keel laid交船日期Date of delivery下水日期Launching date重大改建Major conversion安放龙骨或船舶处于相似建造阶段的日期Date on which keel was laid or ship was at a similar stage of construction 签订改建合同日期Date of conversion contract改建完工日期Date of completion of conversion船舶所有人Owner经营人Operator承租人Charterer船舶编号或呼号Distinctive number or letters航行区域Navigation area/Service area/Trade area曾用过的船名Former Name姐妹船Sister Ship总吨位Gross tonnage净吨位Net tonnage排水量Displacement载货量Cargo weight载重量Deadweight空船重量Light(-ship) weight吃水(首、尾、平均) Draft ( fwd, aft, mean)稳性Stability完整稳性Intact stability破舱稳性Damaged stability分舱（抗沉性）Subdivision初稳性高度Meta-centric height衡准数Criterion numeral剖面模数Section modulus惯性矩Moment of inertia纵总强度Longitudinal strength局部强度Local strength方形系数Block coefficient静水弯矩Still water bending moment重心垂直高度Vertical height of centre of gravity屈服应力Yield stress标准舷弧Standard sheer防火分隔Fire division航区限制Navigation area restriction海况限制Sea state restriction天气限制Weather restriction最大抗风暴能力Max. weatherliness储备浮力Reserve buoyancy续航力Endurance渗透率Permeability盲区Blind area共振区域Resonance region容许载荷Permissible load核定载客数Number of persons certified to carry干舷：Freeboard热带干舷Tropical freeboard夏季干舷Summer freeboard冬季干舷Winter freeboard北大西洋冬季干舷Winter North Atlantic freeboard热带木材干舷Timber tropical夏季木材干舷Timber summer冬季木材干舷Timber winter北大西洋冬季木材干舷Timber winter North Atlantic freeboard 淡水宽限Allowance for fresh water减少干舷的B型船舶Type B with reduced freeboard舱室处所Compartments or Spaces舱室工作和设备舱室：驾驶室 wheel house海图室chart house报务室radio room雷达室tadar room声纳室sonar room主机舱main engine room主机操纵室main engine control room辅机舱auxiliary engine room锅炉舱boiler room机炉舱engine and boiler room减速器舱reduction gear room舵机舱steering gear room通风机室fan room变流机室commutator room空调室air-conditioner room应急发电机室emergency generator room 冷冻机室refrigerator room灭火装置室fire control room蓄电池室battery room陀螺罗经室gyro-compass room方位水平仪室azimuth level room计程仪舱log room导弹舱missile room弹药舱magazine深弹舱depth charge room弹药转运舱ammunition lobby声纳舱sinacelle, sonar nacelle机修间workship电工间electrician’s store木工间carpenter’s store锚链舱chain locker桅屋mast house洗消室decontamination room居住舱室：accommodation居住舱室living accommodation客舱cabin船员舱室crew’s cabin墙壁wall天花板top ceiling侧壁板side ceiling里子板lining装饰decoration家具furuiture书桌desk衣橱wardrobe梳妆台dressing table书柜bureaux餐具柜dresser椅子chair沙发sofa桌子table帷幔drapery窗帘curtain地毯carpet货舱：货舱货油舱集装箱舱冷藏货舱液化天燃气舱邮件舱行李舱汽车舱液舱燃油舱滑油舱压载水舱淡水舱污水舱储藏室帆缆间油漆间粮食库冷藏库其他：首尖舱尾尖舱顶边舱：甲板强横梁与舱口一直线的垂直边板船壳板斜底板底边舱双层底舱翼舱边舱平衡舱深舱残油舱隔离空舱空舱cargo hold（详见船体部分的货舱）cargo oil tankcontainer holdrefrigerated cargo holdliquefied natural gas tankmail roomluggage roomvehicle holdliquid tankfuel oil tanklubricating oil tankballast tankfresh water tankbilge tankstore, store roomhawser storepaint roomprovision storerefrigerating chamberfore peak tankaft peak tanktopside tankdeck transversevertical side plating in line with hatch shell platingsloping platinghopper side tankdouble bottom tankwing tankside tankheeling tankdeep tanksludge/oil residue tankcofferdamvoid tank处所货物处所：Cargo spaces货舱Cargo hold货油舱Cargo oil tank液货舱Liquid cargo tank围壁通道Trunk起居处所：Accommodation spaces 公共处所Public space走廊Corridor盥洗室Lavatory住所Cabin办公室Office医务室Hospital放映室Cinema游戏室Game room娱乐室Hobby room理发室Barber shop配膳室(无烹调设备) Pantry(containing no cooking appliances) 公共处所：Public spaces:大厅Hall餐室Dining room休息室Lounge类似的固定围闭处所Similar permanently enclosed spaces服务处所：Service spaces：厨房Galley配膳室(设有烹调设备的) Pantry (containing cooking appliances) 储物间Locker邮件舱Mail room贵重物品室Specie room储藏室Store room工作间Workshop围壁通道Trunk特种处所：Special category spaces：舱壁甲板以上或以下围闭的车辆处所Enclosed vehicle spaces above and below the bulkhead deck机器处所：Machinery spaces：A类机器处所Machinery space of category A装有下列机械的处所推进机械；锅炉；燃油装置；蒸汽机和内燃机；发电机和主要电动机；加油站；冷藏机；防摇装置；通风机；空气调节机械。
船舶英语——精选推荐
船舶英语floating launch飘浮下⽔gravity launch重⼒下⽔grease launch油脂下⽔steel ball method of launch钢珠下⽔mechaniz launch机械化下⽔end launch纵向下⽔side launch横向下⽔incline launch倾斜下⽔jump launch跳跃式下⽔dipp launch跌⼊式下⽔two-point support launch两⽀点下⽔up to slipway上排marine slipway下⽔重量launch weight下⽔重量launch grease下⽔油脂pressure bear layer乘压层transitional layer过渡层slid layer滑动层weight of up to slipway上排重量lift by the stern尾浮lift尾浮fore poppet pressure前⽀架压⼒zone of pivot pressure action前⽀架压⼒作⽤区way end pressure滑道末端压⼒dropp⾸落bow drop⾸落dipp⾸沉tipp尾落launch poppet下⽔⽀架fore poppet前⽀架after poppet后⽀架launch beam下⽔横梁trigger⽌滑器check arrangement制动设施sub-assembl部件装配section assembl分段装配unit assembl分段装配berth assembl船台装配unit erection at berth船台装配sectional method of hull construction分段建造法block method of hull construction总段建造法horizontal method of hull construction⽔平建造法pyramid method of hull construction塔式建造法island method of hull construction岛式建造法upright method of hull section construction正装法upsidedown method of hull section construction倒装法sideward method of hull section construction侧装法join ship sections afloat⽔上合拢mould bed胎架jig胎架fixed mould bed固定胎架adjustable mould bed可调胎架positioner摇摆胎架tilt jig回转胎架tilt device回转装置specialized mould bed专⽤胎架bed mould胎板fabrication platform装焊平台electromagnetic platform电磁平台position strip定位马shore定位马electromagnetic strip电磁马jip for fitt-up T-sectionsT型材装焊机temporary stiffen bar临时加强材assembly frame假舱壁sub-assembly船体部件panel板列section分段assembly分段unit分段basic section基准分段join section嵌补分段flat section平⾯分段curved section曲⾯分段three-dimensional unit⽴体分段two-dimensional unit半⽴体分段block总段complete cross section总段section assembly flow line分段装配流⽔线lay-out for assembl装配划线sequence of erection and weld装配焊接顺序plate alignment拼板position定位frame r肋⾻框架reference line for assembl装配定位线seperate method of assembl分离装配法cell method of assembl放射式装配法interpolate method of assembl插⼊装配法centerlineof berth船台中⼼线sight column望⼴柱positioner for unit erection at berth船台装配定位器frame station line on berth船台肋⾻线light target光靶pre-set焊接反变形manual loft⼿⼯放样scale loft⽐例放样full scale loft实尺放样longitudinal shrink scale loft纵向缩尺放样fair光顺fairness光顺性deviation from offsets修正值coincide in three projection planes三⾯吻合lay off of hull lines型线放样mathematical loft数学放样mathematical lines数学型线mathematical fair of lines型线数学光顺sectional curved method剖⾯线法least square method最⼩⼆乘法linear programm method线形规划法variational method变分法curved surface method曲⾯法point by point method of modification逐点修改法local linear interpolation直尺卡样法elastic local linear interpolation卡尺回弹法bend-modify relaxation method弯调松弛法interpolation point正插点inversed interpolation point反插点line of intersect points⾓点线line of tangential points切点线line of centers圆⼼线localized fair局部光顺circular spline圆弧光顺spline function样条函数fitt拟合fitt to curved surface曲⾯拟合parametric curve with sle flecnode单拐参数曲线criterion of fairness光顺判别准则inflexion preservation保凹凸recurrent force回弹⼒coincident recurrent force正回弹⼒incoincident recurrent force返回弹⼒recurrent magnitude回弹量bend direction of curve弯向chang of curvature弯势excess flecnode多余拐点bad point坏点bad point interval坏点区discriminat function定改函数mathematical development of shell plate外板数学展开equation of frame肋⾻⽅程equation of longitudinal seam纵缝⽅程equation of transverse seam横缝⽅程differential geodesic line method微分测地线法tangential development method切⾯展开法thickness modification in plate development板厚修正shipbuild information data process造船信息数据处理系统mathematical loft system for pip管路数放系统graphic data process system图⽰数据处理系统line fair program型线光顺程序seam arrangement program板缝排列程序shell plate development program外板展开程序mathematical seam arrangement板缝数学排列nest program套料程序structural process program结构处理程序nest mathematical process套料数学处理structural mathematical process结构数学处理tape out-put program纸带输出程序draw process program绘图处理程序numerical controlled draw 数控绘图data treatment and memory program数据处理和存储程序station No站号frame No肋⾻号contour line外廓线shell pate development外板展开dutum line准线mean normal method准线展开法center spot squar method⼗字线展开法geodesic line测地线geodesic line development method测地线展开法frame section surface肋⾻平⾯normal plane of shell plate外板法⾯trible of buttock lines纵剖线族tribe of body lines横剖线族tribe of water lines⽔线族camber table梁拱表frame interpolation肋⾻插值frame body plan肋⾻型线图returned table of offsets完⼯型值表finished table of offsets完⼯型值表draft mark吃⽔标志paint line⽔线标志structural member loft结构放样edge line接⼝线upper edge line上⼝线lower edge line下⼝线seam arrangement板缝排列longitudinal seam纵向接缝transverse seam横向接缝curved surface development曲⾯展开structural member development构件展开curvature of frame肋⾻弯度jig for plate development外板展开器selected mould sectionprojected frame line on selected mould section改型肋⾻型线diagonal check methods对⾓线检查法sketch for mark off号料草图template draw样板图scale draw transparency投影底图glass negative投影底⽚profile draw仿形图bridge line连割线template样板mould样板mock-up样箱cradle mould样箱batten样条mould bar洋棒multi-shape template格⼦样板adjustable mould可调样板triangular template三⾓加⼯样板beam mould梁拱样板frame mould肋⾻洋板section mould加⼯洋板template for secondary mark装配划线样板angular template for assembl装配夹⾓样板adjustable angular template可调⾓度样板template for mark-off号料样板loft office放样间loft floor样台scale loft table⽐例放样台manual mark-off⼿⼯号料mark-off from templates样板号料mark-off from mould bars样棒号料mark-off from moulds样箱号料mark-off from sketches草图号料secondary mark-off⼆次号料nest套料mark signs号料符号fram line构架线automatic mark-off⾃动号料projection mark投影号料projection tower投影塔projection room投影室projection mark table投影号料台positive projection正⽚投影negative projection负⽚投影image distortion影像畸变absolute distortion绝对畸变relative distortion相对畸变pincushion distortion枕形畸变barrel distortion桶形畸变photosensitive mark感光号料facsimile mark电传真号料facsimile mark machine电传真号料机electro-print mark电印号料electro-print mark apparatus电印号料装置synchronized scann projection同步扫描投影photo-conductive powder光电粉末electrostatic latent image静电潜像NCshapes mark machine数控型材号料pneumatic mark punch风动号料冲头shipbuild technolgy造船⼯艺two-part construction两段造船法method of build ship in two sections两段造船法tandem shipbuild method串联造船法technology of hull construction船体建造⼯艺loft放样mark off号料hull steel fabrication⾦属船体加⼯assembly and erection船体装配weld焊接launch下⽔outfitt and machinery installation船舶设备和系统安装pre-erection outfitt预安装outfitt and machinery installation on berth船台安装quay outfitt and installation码头安装dock outfitt and installation船坞安装unit outfitt单元安装unit pre-outfitt单元预装bollard test系泊实验sea trial航⾏实验construction start date建造开⼯⽇time on build berth船台周期shipbuild period造船周期launched displacement of ships下⽔量ship output船舶产量ship delivery交船operation stage⼯艺阶段operation items⼯艺项⽬operational path⼯艺路线technological process⼯艺过程technological instruction⼯艺规程method plann of ship construction原则⼯艺standard technological procedure典型⼯艺operation items detail chart⼯艺项⽬明细表master schedule总⼯艺进度表"positional flow" method流⽔定位法"specialized gang" method流⽔定员法edge preparation边缘加⼯individuals of hull structure船体零件symbols for hull steel fabrication船体加⼯符号groove preparation坡⼝加⼯edge plann刨边edge mill铣边edge grind磨边carbon arc air goug碳弧⽓刨plate-edge planer刨边机plate-edge miller铣边机shear剪切roll shear滚剪blank冲切scarf削斜flame cutt⽕焰切割plasma cutt等离⼦切割arc air cutt电弧⽓割gas cutt⽓割oxy cutt氧⽭切割oxy-flux cutt氧熔剂切割laser cutt激光切割under water cutt⽔下切割stack cutt迭板切割shear squence剪切顺序drag后拖量shear machine剪床guillotine龙门剪床roll shear machine滚剪机disk shear圆盘剪circular shear圆盘剪nibbl machine振动剪床shear and punch machine联合冲剪机semi-automatic gas cutt machine半⾃动⽓割机gantry type semi-automatic gas cutt machine半⾃动桥式⽓割机semi-automatic gas cutt machine for mark circular shape半⾃动割圆机semi-automatic multitorch gas cutt machine半⾃动多炬⽓割机全位置仿形⽓割机all position copy gas cutt machine全位置仿形⽓割机automatic gas cutt machine⾃动⽓割机profile gas cutt machine靠模⽓割机copy gas cutt machine靠模⽓割机photo-electric trac gas cutt machine光电跟踪⽓割机photo-electric linefollow gas cutt machine光电跟线⽓割机NCgas cutt machine数控⽓割机NCuniversal gas cutt machine数控通⽤⽓割机cutt torch割炬cutt nozzle割嘴preheat⽓割预热roll bend滚弯press bend压弯knuckle折⾓angle bend less than 90折锐⾓angle bend greater than 90折钝⾓flang折边die bend强制弯曲free bend⾃由弯曲concave bend of frame⾻材内弯convex bend of frame⾻材外弯length wise wavws around edge皱折minimum bend radius最⼩弯曲半径pre-bend预弯surplus straight edge剩余直边spr back弯曲回弹rubber mold form橡⽪模成型spinn旋压flow form旋压bulg胀形shot blast form喷丸成型stretch metal in center portion of sheet放中tight metal in center portion of sheet收中stretch metal around edges of sheet放边tight metal around edges of sheet收边hammer solidly around edges of sheet拨缘channell压筋rectification of distortion矫形rectification of distortion by flame⽕⼯矫形rectification of distortion by flame heat and water cool⽔⽕矫形hot form⼤⽕成形line heat form⽔⽕成形heat line加热线heated-side cool method正⾯⽔冷法back-side cool method背⾯⽔冷法width of heat affect zone热影响区宽度length of heat line焰道长度heat speed热源速度flame power⽕焰功率angular distortion⾓变形explosion form爆炸成形unconfined system explosion form⽆模爆炸成形three-roll bend machine三辊弯板机shipyard roll press造船⽤滚压两⽤机shipyard combined plate bend and flang machine造船⽤滚压两⽤机four-roll bend machine四辊弯板机press压⼒机hydraulic press with adjustable head for ship use造船⽤压头可移式液压机three-row plunger type press三排柱塞式弯板机multi-plunger hydraulic press多柱塞式弯板机NChydraulic press数控成形液压机sail-shaped plate帆形板saddle-shaped plate鞍形板screw-shaped plate螺形板corrugated plate波形板channelled plate槽形板cylindrical shaped plate桶形板conical shaped plate锥形板spherical shaped plate球形板pure bend纯弯板concentrated force bend集中⼒弯曲stretch bend拉弯torsional deflection旁弯变形cold frame bend machine肋⾻冷弯机frame roll machine肋⾻滚弯机frame stretch bend machine肋⾻拉弯机cold frame bend machine with-adjustable die可调模具式肋⾻冷弯机cold frame bend machine with multiplungers多压头式肋⾻冷弯机three cylinder frame bend machine三缸肋⾻冷弯机frame pure-bend machine纯弯曲肋⾻冷弯机frame bend machine of medium frequency induction heat中频肋⾻热弯机NCcold frame bend machine数控肋⾻弯曲机concave bend frame内弯肋⾻convex bend frame 外弯肋⾻s-bend frameS-形肋⾻steel pretreatment刚材预处理steel levell and straighten钢材矫正levell of piates钢板矫平mangle辊式矫平机plate straightener辊式矫平机straighten of shapes型钢矫直shapes straighten machine型钢矫直机steel preheat钢材预热rust removal of steel钢材除锈abrasive blast喷射除锈abrasive磨料shot blast抛丸除锈shot blast machine抛丸除锈机shot blast room抛丸室abrasive impeller抛丸器automatic primer spray⾃动喷涂底漆chemical clean化学除锈acid clean of steel酸洗除锈pickl酸洗处理dip pickl浸渍酸洗spray pickl喷淋酸洗neutraliz中和处理passivat钝化处理phosphat磷化处理pickl bath酸洗池pickl waste treatment废酸液处理acid pickl inhibitor酸洗缓蚀剂vacu-blast clean真空喷射除锈arc rust removal电⽕花除锈mechanical rust removal机械除锈secondary rust removal⼆次除锈shot peen喷丸除锈sand blast喷沙除锈wet sand blast湿喷沙除锈spray pickl in circulation循环喷射酸洗acid paste pickl化学膏除锈hydroblast⾼压⽔除锈flame clean⽕焰除锈remote control descal machine遥控除锈机adjust needle cleaner针束除锈器stripp film clean可剥性薄膜除锈section shot-blast分段抛丸除锈section shot-peen分段喷丸除锈section pickl分段酸洗除锈shot-peen room喷丸间brush paint刷涂spray pant喷涂airless spray paint⽆空⽓喷涂electrostatic spray静电喷涂agent for electrostaic spray静电喷涂助剂electrocoat电泳涂漆flow line of pickl酸洗磷化电泳涂漆流⽔线phosphat and electrocoat酸洗磷化电泳涂漆流⽔线abrasive磨料abrasive blast喷射除锈abrasive impeller抛丸器absolute distortion绝对畸变acceptance document验收移交书acceptance of shaft轴系安装验收acid clean of steel酸洗除锈acid paste pickl化学膏除锈acid pickl inhibitor酸洗缓蚀剂actual throat thickness焊缝厚度additional test复验adjustable angular template可调⾓度样板adjustable block机械墩adjustable mould可调样板adjustable mould bed可调胎架adjust needle cleaner针束除锈器after poppet后⽀架agent for electrostaic spray静电喷涂助剂ahead and astern reach measurement惯性试验air tight test of pipeline管路⽓密实验airless spray paint⽆空⽓喷涂alignment找正alignment by flanges直接找正alignment of bottom cas and bear seat下⽓缸和轴承座找正all position copy gas cutt machine全位置仿形⽓割机all position weld全位置焊接anchor test in trial锚设备效⽤实验angle bend greater than 90折钝⾓angle bend less than 90折锐⾓angular distortion⾓变形angular template for assembl装配夹⾓样板anneal weld退⽕焊approved certificate for product产品合格证arc air cutt电弧⽓割arc blow磁偏吹arc clean action阴极破碎arc length弧长arc rust removal电⽕花除锈arc strike引弧arc weld电弧焊arcvoltage电弧电压argon arc weld氩弧焊assembl error装配误差assembl on board上船组装assembly分段assembly and erection船体装配assembly frame假舱壁automatic gas cutt machine⾃动⽓割机automatic primer spray⾃动喷涂底漆automatic weld⾃动焊automatic weld in vertical position垂直⾃动焊auxiliary boiler test辅锅炉试验average linear load平均线负荷back chipp清根back goug清根back run打底焊back settl回淤back weld打底焊backfire回⽕back weld封底焊bad point坏点bad point interval坏点区band test弯曲试验bank slope驳岸barrel distortion桶形畸变base line基准线base metal母材basic covered electrode碱性焊条basic section基准分段basin港池batten样条beam mould梁拱样板beams gate迭梁式坞门bear metal cracks轴承龟裂bed mould胎板bend direction of curve弯向bend of pipewith core有芯弯管bend prior to weld先弯后焊berth船台berth assembl船台装配berth force挤靠⼒bevel angle坡⼝⾓度bilge block舭墩blade rust叶⾯锈斑blade tip deflection螺旋桨叶稍上翘blank冲切block总段block load搁顿负荷block method of hull construction总段建造法block sequence分段多层焊blocks墩blocks with sand box沙箱墩blowhole⽓孔blow吹车boat tank跳船boiler burner test锅炉燃烧器试验boiler water fill上⽔（锅炉）bollard test系泊实验bonded flux陶质焊剂bonded slag粘渣bond of plastic pipe塑料管粘接bond of propeller to shaft螺旋桨胶合联接bor for shaft line轴系镗孔bow drop⾸落box包⾓焊braz钎焊braz filler metal钎料braz flux钎剂break test for anchor chain锚链拉断实验breakwater防波堤bridge approach引桥bridge gauge桥规bridge line连割线brush paint刷涂build berth造船台build dock造船坞bulg胀形burn loss烧损burn of bear metal⽩合⾦烧熔butt joint对接接头butt weld对接焊缝butter预堆边焊caisson坞门camber table梁拱表cambered way弧形滑道canalled dock运河式船坞cantilever end load悬臂端负荷carbon arc air goug碳弧⽓刨carbon equivalent炭当量cargo handl test起重设备负荷试验cast of propeller in metal patten螺旋桨⾦属型铸造cell method of assembl放射式装配法center block for shaft alignment轴系中⼼定位块center line strip on berth船台中⼼线板center spot squar method⼗字线展开法center校中center of mov parts运动件校中center of shaft by indicators指针法轴系校中center of shaft by light光学法轴系校中center of shaft by ruler and gauge直尺和厚薄规法轴系校中center of shaft轴系校中center of shaft by calculation method计算法轴系校中center of shaft by direct connection平轴法轴系校中center of shaft by load method轴承负荷法轴系校中center or rotor转⼦校中centerline of berth船台中⼼线centrifugal cast of propeller螺旋桨离⼼铸造ceramic flux陶质焊剂chain intermittent fillet weld对称间断焊缝chang of curvature弯势channelled plate槽形板channell压筋check of axial clearance轴向间隙确定check of dynamic balance of rotor转⼦校动平衡check of play between piston and cylinder cover校⽓缸余隙check of propeller pitch螺旋桨螺距校正check of reference center line中⼼线测量check of the tappet clearance校⽓门间隙check arrangement制动设施check of bear clearance with lead压铅法check of propeller pitch螺旋桨螺距检验check of surface in contact by mark compound涂⾊油法chemical analysis化学分析chemical clean化学除锈circular shear圆盘剪circular spline圆弧光顺circumferential weld环焊缝CO2 weld⼆氧化碳⽓体保护焊coat药⽪coincide in three projection planes三⾯吻合coincident recurrent force正回弹⼒cold bend of pipe管⼦冷弯cold crack冷裂缝cold frame bend machine肋⾻冷弯机cold frame bend machine with multiplungers多压头式肋⾻冷弯机complete cross section总段complete engine set installation整机安装complete fusion焊透compressed air test⽓压实验concave bend frame内弯肋⾻concave bend of frame⾻材内弯concentrated force bend集中⼒弯曲configuration of bent pipe管⼦弯势conical shaped plate锥形板connection weld联系焊缝construction start date建造开⼯⽇consumable guide electroslag weld熔嘴电渣焊consumables焊接材料continuous weld连续焊缝continuous weld连续焊contour line外廓线convex bend frame 外弯肋⾻convex bend of frame⾻材外弯copper back铜垫copper shoe铜滑块copy gas cutt machine靠模⽓割机core wire焊芯core wire diameter焊条直径coreless bend of pipe⽆⼼弯管corner joint⾓接接头corrugated plate波形板course keep test航向稳定性试验covered berth室内船台covered electrode焊条cover药⽪crack sensitivity焊接裂缝敏感性crack test抗裂试验crack test with 500x2000mm test pieces⼤板对接抗裂试验cradle mould样箱crater弧坑crater crack弧坑裂缝cribb井字墩criterion of acceptance of radiographic examination of welded seam焊缝质量射线检查评定标准criterion of fairness光顺判别准则criterion of ultrasonic examination of welded seam焊缝超声波探伤标准cruciform crack test⼗字接头抗裂试验cruciform joint⼗字接头curvature of frame肋⾻弯度curved section曲⾯分段curved surface development曲⾯展开curved surface method曲⾯法cutt nozzle割嘴cutt torch割炬cylindrical shaped plate桶形板data treatment and memory program数据处理和存储程序dead center gauge⽌点规defective items after inspection废品通知单deflection of main journal主轴颈下沉量degree of mechanization in weld焊接机械化程度deposited metal熔敷⾦属deposition rate熔敷系数depth of fusion熔深design element of weld焊缝结构要素design throat thickness焊缝计算厚度design water lever设计⽔位destructive examination破坏性检验detectaphone侦听起detection sensitivity探伤仪灵敏度determination of center line and axis找中determination of center line or axis找中determination of shaft linep轴系找中deviation from offsets修正值diagonal check methods对⾓线检查法dial gauge for measur of crank spread曲轴量表die bend强制弯曲differential geodesic line method微分测地线法diffusible hydrogen content扩散氢含量dip pickl浸渍酸洗dip transfer短路过渡dipp⾸沉dipp launch跌⼊式下⽔discriminat function定改函数disk shear圆盘剪dock船坞dock bottom坞底dock entrance坞⼝dock head坞⾸dock outfitt and installation船坞安装dock sill坞坎dock wall坞壁dockgate坞门dockgate channel门槽dock weight进坞重量dolphin pier靠船墩double bevel grooveK型坡⼝draft mark吃⽔标志drag后拖量draw process program绘图处理程序drop test for anchor锚投落试验dropp⾸落dry dock⼲坞dry extension of electrode焊丝⼲伸长dutum line准线dynamic characteristic电源动特性dynamic test of propeller螺旋桨浆动平衡试验dynamometer测功器eccentricity偏⼼度edge grind磨边edge joint端接接头edge line接⼝线edge mill铣边edge plann刨边edge preparation边缘加⼯elastic local linear interpolation卡尺回弹法electric dynamometer电⼒测功器electrocoat电泳涂漆electrode diameter焊条直径electrode extension焊丝伸出长度electrode for vertical down weld下⾏焊条electrode negative正接electrode positive反接electromagnetic platform电磁平台electromagnetic strip电磁马electronbeam weld电⼦束焊electronic indicator电⼦⽰功器electroslag weld电渣焊electroslag weld with plate electrode板极电渣焊electroslag weld with wire electrode丝极电渣焊electrostatic latent image静电潜像electrostatic spray静电喷涂elevation⽔位emergency drain test应急疏⽔实验enclosed weld强迫成形焊end launch纵向下⽔equation of frame肋⾻⽅程equation of longitudinal seam纵缝⽅程equation of transverse seam横缝⽅程equilibrium tide平潮evaluation test of power plant on board动⼒装置实船鉴定试验examination of opened up parts拆验examination of ream紧配螺栓配合检查excess flecnode多余拐点excess of water过⽔excess weld metal加强⾼expander胀管器explosion expand of pipe爆炸胀管explosion form爆炸成形explosive weld爆炸焊接exposed berth露天船台external characteristic电源外特性fabrication platform装焊平台facsimile mark电传真号料facsimile mark machine电传真号料机fair光顺fairness光顺性fatigue test疲劳试验filler metal填充⾦属filler wire焊丝fillet weld⾓焊缝fillet weld in flat position船形焊fillet weld Tee bend testT型接头弯曲试验fillet weld⾓焊final cutt of pipe割管finished table of offsets完⼯型值表firecracker weld躺焊first product inspection⾸件检验FISCO type crack test加压固定对接抗裂试验fishbone crack test鱼⾻型抗裂试验fitt拟合fitt of compreg层压胶⽊镶嵌fitt of lignumvitae铁梨⽊镶嵌fitt of rubber seal r in stern tube尾轴管衬套橡胶嵌套fitt to curved surface曲⾯拟合fixed foot bridge固定引桥fixed mould bed固定胎架flame bend of pipe⽕焰弯管flame clean⽕焰除锈flame cutt⽕焰切割flame power⽕焰功率flangeless joint⽆法兰联接flang折边flap gate卧倒式坞门flash back回⽕flat position weld平焊flat section平⾯分段flatten test⾦属管压扁试验float caisson浮箱式坞门float launch飘浮下⽔float spar fender浮式护⽊flood dock注⽔式船坞flood test灌⽔法flow form旋压flow line of pickl酸洗磷化电泳涂漆流⽔线flow rate of shield gas保护⽓体流量flux焊剂flux back焊剂垫fog test⽓雾法fore poppet前⽀架fore poppet pressure前⽀架压⼒formation of weld寒风成形frame bend machine of medium frequency induction heat中频肋⾻热弯机frame body plan肋⾻型线图frame interpolation肋⾻插值frame lines肋⾻检验线frame mould肋⾻洋板frame No肋⾻号frame r肋⾻框架frame roll machine肋⾻滚弯机frame section surface肋⾻平⾯frame station line on berth船台肋⾻线frame stretch bend machine肋⾻拉弯机fram line构架线free bend⾃由弯曲free runn空车运转freeboard measurement of life boat救⽣艇⼲舷测定full penetration焊透full scale loft实尺放样fume of weld焊接烟尘furnace brickwork炉墙砌筑furnace explosion dur light up冷爆fused flux熔炼焊剂gallery廊道gantry龙门架gap两轴曲折gas cutt⽓割gas inflation liferaft test⽓胀式救⽣筏试验gas metal arc weld熔化级⽓体保护焊gas mixture metal arc weld混合⽓体保护焊gas pore⽓孔gas tightness⽓密性gas tungsten arc weld⾮熔化级⽓体保护焊gas weld⽓焊gate chamber门库gate channel for repair修理门槽gate pier门墩generat set portion of bollard test发电机组系泊试验generat set portion of trial test发电机组航⾏试验geodesic line测地线geodesic line development method测地线展开法glass negative投影底⽚globular transfer⼤滴过渡graphic data process system图⽰数据处理系统gravity launch重⼒下⽔gravity weld重⼒焊grease launch油脂下⽔groove坡⼝groove angle坡⼝⾓度groove depth坡⼝深度groove preparation坡⼝加⼯groove radius坡⼝半径guided bend of pipe靠模弯管guillotine龙门剪床hammer solidly around edges of sheet拨缘handl test of life boat救⽣艇和⼯作艇降落试验hard solder钎料hardness test硬度试验hardness test of weld zone焊接接头硬度试验heat affected zone热影响区heat input线能量heat line加热线heat speed热源速度hell test倾斜试验high frequency bend of pipe⾼频弯管hogg拱曲horizontal build berth⽔平船台horizontal method of hull construction⽔平建造法horizontal position weld横焊hot bend of pipe管⼦热弯hot crack热裂缝hot form⼤⽕成形hot wire submerged arc weld预热焊丝埋弧焊hull steel fabrication⾦属船体加⼯hydraulic bend of pipe液压弯管hydraulic dynamometer⽔⼒测功器hydraulic press with adjustable head for ship use造船⽤压头可移式液压机hydraulic subassembly for crankshaft曲轴液压套合hydraulic test of boiler锅炉⽔压实验hydraulic test of pipeline管路液压实验hydroblast⾼压⽔除锈hydrogen content in welds焊缝氢含量idl惰转image distortion影像畸变impact force撞击⼒impact test冲击实验imperfection in bond轴承脱壳incline launch倾斜下⽔inclined build berth倾斜船台inclined Tee joint斜接接头incoincident recurrent force返回弹⼒incomplete fusion未焊透indicator⽰功器individuals of hull structure船体零件inflexion preservation保凹凸insert pipe嵌补管inspection勘验inspection of levelness⽔平度测量inspection by mould bar样条法检验inspection by sketch method草图法检验inspection by templet样板法检验inspection dur hull steel fabrication船体零部件加⼯检验inspection of abutt edges of block总段对接检验inspection of block总段装配检验inspection of center line of build berth船台中⼼线测量inspection of draft mark and loaded water linesinspection of frame spac肋⾻间距测量inspection of groove坡⼝测量inspection of hull deformation after launch全船校正检查inspection of hull form after completion船体完⼯测量inspection of hull lines线型检验inspection of hull loft船体放样检验inspection of install of propeller螺旋桨安装检查inspection of mould bed胎架检验inspection of mount of bear seats轴承座安装检验inspection of panel平⾯分段检验inspection of permanent ballast before launch下⽔压载检查inspection of preassembled frame r肋⾻框架装配检验inspection of ship structure全船结构检查inspection of squar accuracy⾓尺线检查inspection of three dimensional unit⽴体分段检验inspection of thrust block推⼒块厚度检查inspection of vertical surface垂直度测量inspection on development of structural members船体构件展开检验inspection on shell plate development外板展开检验installation of boiler锅炉安装installation of desel engine柴油机安装installation of main engine主机安装installation of marine power plant船舶动⼒装置安装installation of pip管系安装installation of pip unit管系单元安装installation of shaft轴系安装installation of turbine汽轮机安装interlayer temperature层间温度intermittent weld间断焊缝interpass temperature层间温度interpolate method of assembl插⼊装配法interpolation point正插点inversed interpolation point反插点iron powder electrode铁粉焊条iron wedge楔铁island method of hull construction岛式建造法items for acceptance of vessel验收项⽬jetty突堤码头jig胎架jig for plate development外板展开器join lines for hull assembly船体装配对合线join section嵌补分段join ship sections afloat⽔上合拢jump launch跳跃式下⽔keel block龙⾻墩knuckle折⾓knuckl line slipway折线滑道lack of fusion未焊透lagg of boiler锅炉绝热层包扎lamellar tear层状撕裂land tie拉桩lap joint搭接接头laser alignment激光找正laser cutt激光切割launched displacement of ships下⽔量launch下⽔launch beam下⽔横梁launch grease下⽔油脂launch poppet下⽔⽀架launch way滑道launch weight下⽔重量layer焊层lay off of hull lines型线放样least square method最⼩⼆乘法leg of fillet weld焊脚length of heat line焰道长度length wise wavws around edge皱折levell找平levell by level gauge液⾯法找⽔平levell of engine bed机座找平levell of foundation机座找平levell of piates钢板矫平lifebuoy test救⽣圈试验lift by the stern尾浮lift尾浮light target光靶line fair program型线光顺程序line heat form⽔⽕成形line of centers圆⼼线line of intersect points⾓点线line of tangential points切点线line outs of ship equipments船舶综合放样linear porosity链状⽓孔linear programm method线形规划法listen侦听listen rod听⾳棒local linear interpolation直尺卡样法localized fair局部光顺localized porosity密集⽓孔loft放样loft floor样台loft office放样间longitudinal bead bend test纵向焊道弯曲试验longitudinal bead notched bend test纵向焊道缺⼝弯曲试验longitudinal seam纵向接缝longitudinal shrink scale loft纵向缩尺放样longitudinal slipway纵向滑道longitudinal weld纵向焊缝low pressure cast of propeller螺旋桨低压铸造lower edge line下⼝线lowest pressure curve of compartments舱室最⼩压⼒曲线magnetic detection磁性探伤main boiler test主锅炉试验main engine portion of bollard test主机系泊试验main engine portion of trial test主机航向实验mangle辊式矫平机manipulation of electrode运条⽅式manual bend of pipe⼿⼯弯管manual emergency anchor test⼈⼒应急起锚试验manual emergency steer test⼈⼒应急操舵试验manual loft⼿⼯放样manual metal arc weld⼿弧焊manual weld⼿⼯焊marginal wharf顺岸码头marine slipway下⽔重量mark for pipes管⼦划线mark for shaft bor轴系孔划线mark off号料mark signs号料符号master schedule总⼯艺进度表match key on propeller shaft推进器轴配件mathematical development of shell plate外板数学展开mathematical fair of lines型线数学光顺mathematical lines数学型线mathematical loft数学放样mathematical loft system for pip管路数放系统mathematical seam arrangement板缝数学排列maximum linear load最⼤线负荷mean normal method准线展开法measurement of curvature of frame肋⾻弯度测量measurement of finished propeller螺旋桨完⼯测量measurement of fit clearance of propeller螺旋桨配合间隙测量measurement of fit clearance of shaft轴系安装间隙测量measurement of fit clearance of sterntube推进器轴安装间隙测量measur error测量误差measur of crank spread曲轴臂距差测量mechanial bend of pipe机械弯管mechanical blocks机械墩mechanical expand of pipe机械胀管mechanical indicator机械⽰功器mechanical rust removal机械除锈mechanized slipway机械化道脂mechanized weld机械化焊接mechaniz launch机械化下⽔medium frequency bend of pipe中频弯管melt rate熔化系数metal transfer熔滴过渡method of build ship in two sections两段造船法method plann of ship construction原则⼯艺MIG weld熔化级⽓体保护焊mill铣切。
船舶英语汇总审批稿
(Delivery expressions for main engine)68
二十四、空压机和空气系统用语
(Air compressor and Air system)···· 75
二十五、锅炉提交用语
(Delivery expressions for boiler)···77
1．主机Main engine
2．二冲程柴油机Two-stroke diesel engine
3．四冲程柴油机Fore-stroke diesel engine
4．高速柴油机High speed diesel engine
5．中速柴油机Middle speed diesel engine
6．低速柴油机Low speed diesel engine
二十九、救生艇提交过程用语
(Delivery expressions for lifeboat)··92
三十、其他提交项目
(Delivery expressions for other items)···95
三十一、甲板机械系泊试验
(Mooring test for deck machinery)········96
三十二、机舱设备系泊试验
(Mooring test for the equipment in E/R)···98
三十三、谈论故障常用语
（Expressions for trouble）············100
三十四、谈论检修常用语
(Expressions for overhaul)············101
十、常用油类(Oil in common use)·····28
十一、常用量词
船舶的英文作文范文
船舶的英文作文范文英文：As a ship, I have been sailing on the sea for many years. I have witnessed the beauty and power of the ocean, as well as the hardships and challenges that sailors face.I am proud to be a part of the maritime industry and play a vital role in transporting goods and people across the world.One of the most important aspects of my design is my hull. It is carefully crafted to withstand the harsh conditions of the sea, including waves, wind, and storms. My engines are also crucial, as they provide the power needed to move through the water. Without them, I would be unable to navigate the vast ocean.As a ship, I have also experienced the impact of technology on the industry. With the development of new navigation systems, communication devices, and safetyequipment, sailing has become safer and more efficient. However, it is important to remember that technology is not a substitute for experience and skill. A skilled captain and crew are still essential for a successful voyage.In addition to my functional aspects, I also have a unique character and personality. Every ship has its own quirks and idiosyncrasies, which make them special to their crews. Some ships are known for their speed, while others are renowned for their stability in rough seas. As a ship, I am proud to have my own distinct qualities that make me stand out from the rest.Overall, being a ship is a challenging and rewarding experience. I am constantly learning and adapting to new situations, and I am proud to be a part of the global maritime community.中文：作为一艘船，我已经在海上航行多年了。
船舶专用英语汇总
船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多∙船舶专业英语词汇∙船体制图常用英中名词术语对照∙船舶英语(页1) - 设计学习- 千岛热线论....∙船体结构英语∙船舶英语手册1--5.word可编辑.∙Navis.gr - 3Examination Questions For...∙船舶图纸符号大全∙货运保险鉴定常用词汇. 专业.专注.。
船舶英文
1．船舶工程 Ship engineering2．船舶Ship, Vessel3．艇 Boat, Craft4．商船Merchant ship, Commercial ship 5．运输船 Transport ship6．客船Passenger ship7．客货船 Passenger-cargo ship8．货船Cargo ship, Freighter, Cargo carrier 9．干货船 Dry cargo ship10 杂货船 General cargo ship11 多用途货船Multipurpose cargo ship12 散货船 Bulk carrier, Bulk cargo ship13 运煤船 Coal carrier14 运木船 Timber carrier, Log carrier15 矿砂船 Ore carrier16 液货船 Tanker, Liquid cargo17 油船Oil tanker, Oil carrier18 成品油轮Product carrier19 穿梭油轮Shuttle tanker20 滚装船 Roll on-Roll off ship, Ro-Ro ship21 集装箱船 Container ship22 载驳船 Barge carrier, Lighter aboard ship23 渡船Ferry24 驳船Barge, Lighter船舶总布置甲板及舱室1，总布置General arrangement2，舱室布置Interior arrangement3，机舱布置Engine room arrangement4，梯道布置Stair way and passage way arrangement 5，舱Compartment6，舱室Space7，艏尖舱Fore peak8，艉尖舱After peak9，底边舱Bottom side tank10顶边舱Top side tank11边舱Wink tank12底舱Hold13双层底舱Double bottom tank14深舱Deep tank15甲板间舱Between deck space16空隔舱Cofferdam17罗经甲板Compass deck18驾驶甲板Navigation deck,Bridge deck19艇甲板Boat deck20游步甲板Promenade deck21起居甲板Accommodation deck22直升机甲板Helicopter deck23上甲板Upper deck24起货机甲板Winch platform25通道Passage, Alleyway26内通道Interior alleyway27外通道Exterior passage way28跳板Ramp29驾驶室Wheel house,Navigation bridge 30海图室Chart room31报务室Radio room32雷达室Radar room33机舱Engine room34锅炉室Boiler room35泵舱Pump room36锚链舱Chain locker37舵机舱Steering engine room38通风机室Fan room39消防控制室Fire-control room40桅室Mast room41声呐室Sonar transducer space42机修间Work shop43起居舱室Accommodation living quarter居住舱室Cabin45船长室Captain room46大副室Chief officer room47轮机长室Chief engineer room48大管轮室First engineer room49船员室Crew room50客舱Passenger cabin51货舱Cargo hold, Cargo space货油舱Cargo oil tank53集装箱舱Container hold54冷藏货舱Refrigerated cargo55车辆舱Vehicle hold56液化天然气舱Liquefied natural gas tank 57行李舱Luggage room58液舱Liquid tank59燃油舱Fuel oil tank滑油舱Lubricating oil tank61污油舱Sludge tank,Dirty oil tank62压载水舱Ballast water tank63淡水舱Fresh water tank64饮水舱Drinking water tank基本投影面与船舶主要尺度1．船体型表面Molded hull surface2．型排水体积Hull volume3．中站面Mid-station planeBase plane5．中线面Center line plane6．基线Base line7．主尺度Principal dimensions8．总长Length overall9．最大长度Extreme length10 垂线间长Length between perpendiculars(Lpp) 11 水线长Waterline length12 设计水线长Designed waterline length(Lwl)13 满载水线长Load waterline length14 型宽Molded breadth15 最大宽Extreme breadthMolded depth 17 吃水Draft, Draught18 型吃水Molded draft 19 设计吃水Designed draft 20 结构吃水Scantling draft 21 艏吃水Fore draft22 艉吃水After draft23 平均吃水Mean draft24 满载吃水Loaded draft 25型线图Lines plan26艏垂线Forward perpendicular 27艉垂线After perpendicular28站Ordinate station29中站Mid-station30型线Molded lines31型值表Table of offsets32横剖面Transverse sections 33水线面Water plane34纵剖面Longitudinal section 油船外观,装置1．船首标志Head mark2．锚Anchor3．首吃水标志Forward draft mark 4．球鼻首Bulbous bow5．中部吃水标志Mid-ship draft mark 6．螺旋桨Propeller7．舵Rudder8．起锚机Windlass9．前桅Fore mast10 通风筒Ventilator11 十字缆柱Cross bite12 甲板部门仓库Deck store13 吊杆Derrick boom14 吊柱Derrick post15 天线桅Antenna pole16 救生艇Life boat17 桥楼Bridge18 雷达桅Radar mast19 烟囱Funnel20 舷梯Accommodation ladder 21 货油装载站Loading station22 通用导缆器Universal chock23 水线Draft line24 货油舱口Cargo oil hatch25 货油管Cargo oil pipe尾机型货船1.舵Rudder2.螺旋桨Propeller3.尾锚，大流锚Stream anchor4.舭龙骨Bilge keel5.舷梯Accommodation ladder6.绞缆机Mooring winch7.双柱系缆桩Ballard8.导缆孔Fair-leader9.蔬菜库Vegetable chamber 10 天窗Skylight11 烟囱Funnel12 菌型通风筒Mushroom ventilator 13 喇叭形通风筒Cowl head ventilator 14 救生艇Lifeboat15 吊艇装置Lifting gear16 雷达桅Radar mast17 测向仪天线Direction finder antenna 18 航迹灯Range light19 桅顶灯Mast head light20 舷灯Side light21 吊杆柱King post22 起货机Winch23 吊货杆Derrick boom24 吊杆柱Derrick post25 前桅Hatch26 货仓口On-deck girder。
船舶货物移动演习中英文范文
船舶货物移动演习中英文范文Ships are an essential mode of transportation for goods and materials around the world. In order to ensure the smooth and efficient movement of cargo, it is important to regularly conduct cargo handling drills and exercises. These drills help to improve the coordination and cooperation among the crew members, as well as ensure that they are prepared to handle any challenges that may arise during cargo operations.One such cargo handling exercise is the "ship-to-shore" drill, which simulates the transfer of cargo from a ship to a shore facility. This exercise is typically carried out in a controlled environment, such as a training facility or a harbor, and involves the use of specialized equipment and procedures.During the drill, the crew members practice loading and unloading cargo from the ship, using cranes, forklifts, and other handling equipment. They also practice securing the cargo in the ship's hold and on the deck, using ropes, chains, and other securing devices. In addition, the crew members practice communication and coordination among themselves and with the shore facility, using radios, phones, and other communication devices.The "ship-to-shore" drill is an important part of a ship's routine training, as it helps to ensure the safe and efficient movement of cargo. It also helps to prevent accidents and injuries among the crew members, as they are able to practice and refine their skills in a controlled environment.Overall, cargo handling drills and exercises are crucial for the smooth operation of ships and the safe movement of cargo. By regularly conducting these drills, ship crews can improve their skills and coordination, and be better prepared to handle the challenges of cargo operations.。
船舶管理英文作文
船舶管理英文作文Ship management is a complex and demanding task that requires a high level of expertise and attention to detail. From ensuring compliance with regulations to maintaining the safety and efficiency of the vessel, ship management involves a wide range of responsibilities.One of the key aspects of ship management is the maintenance of the vessel. This includes regular inspections, repairs, and upgrades to ensure that the ship is in optimal condition. Proper maintenance is crucial for ensuring the safety of the crew and the cargo, as well as for maximizing the lifespan of the vessel.In addition to maintenance, ship management also involves managing the crew and ensuring that they have the necessary training and resources to carry out their duties effectively. This includes providing ongoing training and support, as well as managing crew schedules and ensuring compliance with labor regulations.Another important aspect of ship management is the financial management of the vessel. This includes budgeting, cost control, and financial reporting to ensure that the vessel operates within budget and remains financially viable.Furthermore, ship management also involves ensuring compliance with international regulations and industry standards. This includes environmental regulations, safety standards, and security protocols, all of which areessential for the safe and efficient operation of the vessel.Overall, ship management is a multifaceted and challenging task that requires a high level of expertiseand attention to detail. By effectively managing maintenance, crew, finances, and regulatory compliance,ship managers play a crucial role in ensuring the safety, efficiency, and success of the vessel.。
对于船舶的看法英文作文
对于船舶的看法英文作文下载温馨提示:该文档是我店铺精心编制而成，希望大家下载以后，能够帮助大家解决实际的问题。
文档下载后可定制随意修改，请根据实际需要进行相应的调整和使用，谢谢!并且，本店铺为大家提供各种各样类型的实用资料，如教育随笔、日记赏析、句子摘抄、古诗大全、经典美文、话题作文、工作总结、词语解析、文案摘录、其他资料等等，如想了解不同资料格式和写法，敬请关注!Download tips: This document is carefully compiled by theeditor. I hope that after you download them,they can help yousolve practical problems. The document can be customized andmodified after downloading,please adjust and use it according toactual needs, thank you!In addition, our shop provides you with various types ofpractical materials,such as educational essays, diaryappreciation,sentence excerpts,ancient poems,classic articles,topic composition,work summary,word parsing,copyexcerpts,other materials and so on,want to know different data formats andwriting methods,please pay attention!Boats are really cool. You can go on adventures on the water.Ships are huge! They carry so much stuff across the oceans.Sailing on a ship can be such an amazing experience. You get to see the sea and the sky.Some ships are super fancy with all kinds of luxuries. It's like a floating hotel.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
船舶英文词汇对照表甲板部分Rank 船员职务rank of ship’s crewCrew 船员seaman、mariner、sailor船员职务（Senior officer 高级船员）Captain 船长，（CAPT）master 船长是全船最高领导者，总管全船所有事物，拥有最高权限。
Chief officer 大副，（C/O）船舶二把手，职务仅次于船长在船长无法行驶职能时接替船长位置。
Second officer 二副（2/O）Third officer 三副（3/O）Assistant officer 驾助、驾驶助理、舵长Chief engineer 轮机长、老轨、大车（C/E）船舶机舱部主要负责人、船舶三把手Second engineer 大管轮、二轨、二车（2/E）Third engineer 二管轮、三轨、三车（3/E）Fourth engineer 三管轮、四轨、四车（4/E）Electric engineer 电机员（E/E）Assistant engineer 轮机助理、轮助普通船员Cadet 实习生、卡带DECK CADET 甲板实习生、ENGINE CADET轮机实习生Bosun 水手长（BSN）Fitter ，Carpenter 木匠（FTR）Able seaman （A.B）全能水手，一水Ordinary seaman （OS）普通水手、二水NO.1 Motorman 机工长Motorman 机工（M/M）Oiler 加油工（OIL）Wiper 抹油工（WIP）Chief cook 大厨（cook）Waiter 、Steward 服务员，大台（STDW）船舶靠港登轮人员Pilot 引航员，领航员，锚地引领员Agency ，Agent 代理，船舶代理。
简称：船代Watch man 梯口值班人员（船舶驾驶人员兼职）：船舶靠港后，海事局要求在船舶上下船处设立签到值班台，等级上下船舶人员名字，职务，来船目的，上下船时间等，并发放登轮许可证。
Custom officer 海关官员，登轮检查船舶货物、船员物品是否符合海关要求。
Immigration officer 移民检察官，边检人员：检查船员是否人证合一，船舶是否有偷渡人员Quarantine officer 检验检疫检察官：现在合并到海关了，预防船舶带来传染性疾病。
Commodity inspection 商检：商业检查，第三方检测，提供公平的货物质量，数量报告Cargo inspector 商检人员Surveyor 商检测量人员Ship owner 船东Cargo owner 货主Supervision 监卸监装loading masterAnimal and plant quarantine officer 动植物检察官Bunker 船舶燃料供应员Ship surveyor 验船师PSC 中国海事局检察官port state controlWaterman加水员船舶锚泊词汇Anchorage 锚地Port 港口Berth 泊位Anchor 锚Cables 锚链Windlass 锚机Ship anchoring 抛锚Gangway ladder 舷梯，登轮梯（accommodation ladder）Pilot ladder 引水梯，比较危险。
Mooring winch 绞缆机Quarantine anchorage 检疫锚地Traffic boat 交通艇船体词汇一览表Starboard右舷Port 左舷Head 船头Bow 船头左右两舷Stern 船尾Midship 船中LOA 船长Beam 船宽Draft 船舶吃水（水线以下部分）Draft forward前吃水Draft middle 中吃水Draft after 尾吃水Waterline 吃水线Free board 干舷1S ,1P 一舱右一舱左Capacity plan 舱容表（cargo capacity plan）货舱舱容表 VTS vessel traffic system 船舶交通管理系统AIS automatic identification system 船舶自动识别系统船舶舱室Deck 甲板层Deck office room甲板办公室Ballast room 压载室，卸货室cargo tank 货舱Cabin 船舱室，一般意思是船员房间也可以说room。
Accommodation deck 居住舱室Upper deck 上甲板Navigation deck 驾驶甲板，驾驶台（wheel house）Radio room 发报室，电子邮件往来室Main engine room 主机间，轮机间Ballast tank 压载舱Toilet 厕所Gallery 厨房Dining room 餐厅船舶种类中英对照Tank 油轮VLCC ULCCDirty tank 原油油轮（crude oil tank）Product tank 成品油油轮（product carrier）SR /MR/ LR 三种类型成品油油轮分别表示短途、中途、长途三种型号short range、medium range、long rangeBunker 加油船Bulk 散货船Traffic ship 交通艇Tug 拖轮Vessel 商船Container carrier 集装箱船舶Chemical carrier 化学品船Roro ship 滚装船，用于汽车运输roll on-roll offLNG 液化天然气liquefied natural gas carrier 液化天然气运输船LPG 液化石油气liquefied petroleum gas carrier 液化石油气运输船 Shipyard 船厂dry dock 干船坞船舶主要部件名称Propeller 螺旋桨，推进器Main engine 主机Steer 舵机Rudder 舵Windlass 锚机Winch 绞缆机Mooring rope 缆绳（rope）Bow thruster 船舶艏侧推Cargo pump 货油泵Cargo cubic 货舱容积Cargo oil 货油Level gauge 液位计Fuel 燃料油Heavy fuel oil 重油，质量较差的船舶燃料油Diesel oil 柴油Lubricating oil 润滑油Hydraulic oil 液压油Binocular 望远镜航海术语Greenwich Mean Time，GMT 格林威治之间Universal Time Coordinated，UTC 世界协调时我们经常会提到UTC和GMT，这两者几乎是同一概念。
它们都是指的格林尼治标准时间，只不过UTC的称呼更为正式一点。
两者的区别在于前者是一个天文上的概念，而后者是基于一个原子钟。
在UTC中，每一年或两年会有一个“闰秒”，例如北京时间=GMT+8=UTC+8Summer Time 夏令时世界各国为了减少能源消耗，尽早入睡一般在天亮早的夏季人为将时间调快一小时，各国家进入夏令时的时间有所不同。
中国在1992年停止使用夏令时。
Suez canal 苏伊士运河Panama canal 巴拿马运河Voyage 航次Mayday 遇险呼救Abandon ship 弃船Hampered ship 操作受限船舶Spill 溢油Windward 上风向Tide 潮汐tide tableWhistle 汽笛ETA （arrival）预计到港时间ETB（berthing）预计靠泊时间ETD（departure）预计离港时间ETS预计开航时间（sailing）Position 船位Traffic lane 航道Course 航向course to 175 degrees。
航向175度Radar 船用雷达Coast guard 海岸警卫队Port authority 港方商检上船用语Document 文件Ship’s particular 船舶资料（包括船舶设计所有数据）Ullage report 空距报告（货舱空距报告）Stowage plan 配载图（船舶装货位置及种类）Dry certification 干舱证（验舱证：证明上一港装货完毕后，进行过舱室检查）Vessel experience factor （VEF）船舶经验系数ROB Remaining on Board 卸货后船货舱及管线内残留油品数量OBQ On Board Quantity 装货前船舶货舱及管线内残留油品数量Last three cargoes 前三次载货种类Demurrage charge 滞期费Discharge/loading rate 卸装货速率Bill of loading 提单（B/L）Port clearance 港口许可证Net 净吨Gross 总吨More or less clause 溢短装条款Supervision of loading/discharge 监装、卸Certificate of origin 货物原产地证书Gulf 沿岸中东沿岸middle east gulfCustoms-clearance/declaration 海关申报Copy 副本three copies for this 复印三个副本船代英文Arrival condition 到港记录（涉及船舶到港时候的所有数据信息）Departure condition 离港记录Tonnage certificate 船舶吨位证书Registry certificate 国籍证书Seaman book 船员证Cargo declaration 货物总申请Crew list 船员名单Officer license 高级船员适任证书 Protective agent 保护代理Boarding permit 登轮证。