常见钻井缩写及含义
钻井术语解释
钻井术语解释钻井术语解释常用术语解释1、井：以勘探开发石油和天然气为目的的，在地层中钻出的具有一定深度的圆柱形孔眼。
2、井口：井的开口端。
3、井底：井的底端。
4、裸眼：未下套管部分的井段。
5、井深：从转盘补心面至井底的深度。
6、井壁：井眼的圆柱形表面。
7、环空：井中下有管柱时，井壁与管柱或管柱与管柱之间的圆环形截面的柱状空间。
8、井眼轴线：井眼的中心线。
9、井身结构：指的是钻头钻深、相应井段的钻头直径、下入的套管层数、直径及深度、各层套管外的水泥返高以及人工井底等。
10、人工井底：设计的最下部油层下的阻流环或水泥塞面。
(注：该定义不全面，人工井底是可变的 )11、井的类别：按一定依据划分的井的总类。
按钻井的目的可分为探井和开发井等；按完钻后的井深可分为浅井 (<1200m) 、中深井(1200 ～3000m) 、深井(3000 ～5000m)和超深井(>5000m) ；按井眼轴线形状可分为直井和定向井。
12、探井：指以了解地层的时代、岩性、厚度、生储盖的组合和区域地质构造，地质剖面局部构造为目的，或在确定的有利圈闭上和已发现油气的圈闭上，以发现油气藏、进一步探明含油气边界和储量以及了解油气层结构为目的所钻的各种井，包括地层探井、预探井、详探井和地质浅井。
13、开发井：指为开发油气田所钻的各种采油采气井、注水注气井，或在已开发油气田内，为保持一定的产量并研究开发过程中地下情况的变化所钻的调整井、补充井、扩边井、检查资料井等。
14、直井：井眼轴线大体沿铅垂方向，其井斜角、井底水平位移和全角变化率均在限定范围内的井。
15、定向井：沿着预先设计的井眼轨道，按既定的方向偏离井口垂线一定距离，钻达目标的井。
16 、丛式井：在一个井场上或一个钻井平台上，有计划地钻出两口或两口以上的定向井（可含一口直井）。
17、救援井：为抢救某一口井喷、着火的井而设计、施工的定向井。
18、多底井：一个井口下面有两个或两个以上井底的定向井。
钻井常用的英文缩写
英文钻井日志常用缩写词汇（按照钻井施工顺序排列）DC---------drill collar 钻铤DP---------drill pipe 钻杆TD---------true depth 垂直井深TD---------total depth 总进尺，总深度USG-------united states gallon 美制加仑Hrs---------hours 小时Drlg-------drilling 钻进，钻井Circ--------circulating 循环Hi. Vis.----high viscosity 高粘度CSG-------casing 套管POOH-----pull out of hole 起钻R/U--------rig up 安装SXS-------sacks 袋子WOC------wait on cement 候凝MW--------mud weight 泥浆比重N/U--------nipple up 安装P/U---------pick up 上提，提起TIH--------trip in hole 下钻Cmt--------cement 水泥DCS-------drill collar stem 钻铤柱ISF---------induction-spherically focused log 感应-球形聚焦测井LSS--------long-space sonic (log) 长源距声波测井GR---------gamma ray log 自然伽马测井LCST------lower critical solution temperature 地临界溶液温度R/D--------rig down 拆卸设备N/D--------nipple down 卸下来，拆卸BOPs------blowout preventer stack 防喷器组合结构M/U-------make-up 上扣，连接，接单跟BHA-------bottom hole assembly 下部钻具结构PV---------plastic viscosity 塑性粘度YP---------yield point 屈服点，流动点Sols--------solids 固相含量PH---------acidity or alkalinity 酸碱度Cond.------conditioned 处理，调整LOT--------leak-off test 地层抗破强度试验，套管鞋下边破裂压力试验EMW------equivalent mud weight 当量泥浆比重ROP-------rate of penetration 机械钻速FPH--------feet per hour 英尺/小时WL---------water loss 滤失量，失水B/U---------bring-up 暂停，是停止，中断KCL--------potassium 氯化钾Stds---------stands 钻杆或钻铤立柱JB-----------junk basket 随钻打捞杯L/D---------lay down 卸下，甩下，放下RIH---------run in hole 下钻GB----------globe basket 牙轮打捞篮Jts-----------joints 单根Bttm--------bottom 底，井底，底部Wt----------weight 重量，比重WOB-------weight on bit 钻压DLL--------dual later log 双侧向测井NGT--------natural gamma ray spectroscopy tool 自然伽马能谱测井LDT--------litho-density tool 岩性密度测井HDT--------high-resolution dipmeter tool 高分辨率地层倾角测井MSFL------micro-spherically focused log 微球形聚焦测井CNL--------compensated neutron (porosity) log 补偿中子（孔隙度）测井RFT---------repeat-formation tester 重复式地层测试器WST--------well seismic tool 井场地震仪Fin.---------finish 结束，弄完，干完PB----------plugged (plugging) back 打水泥塞，回填CBL--------cement bond log 水泥胶结测井VDL--------variable density 变密度测井（=VDC）CCL--------casing collar locator log 套管接箍地位器（测井）Pkr----------packer 封隔器DST---------drill stem tester 钻柱测试器TP-----------test pressure 测试压力FSIP--------final shut-in pressure 最终关井压力FSIT--------final shut-in time 最终关井时间F.L.---------fetch/ load 取出/装入Sudd.-------suddenly 突然Perf.--------perforation 射孔，打眼，炮眼Reptd-------reported 汇报，上报。
石油钻井常用词汇及缩写汇总
石油钻井常用词语及缩写汇总标准钻井日报表内容Official Daily Report Form钻井日报表Daily drilling report2．报表号Report No.3．图例（说明）Legend4．公制度量标准Metric expressions5．所有长度均采用米制，并取两位小数All lengths expressed in metres to two decimal places6．泥浆密度——kg/m3 Mud density = kilogram per cubic meter (kg/m3) 7．泥浆泵冲程mm pump-stroke length=millimetre(mm)8．悬重——十牛顿Weight of string=deca newton(daN)9．单位长度质量——kg/m Linear mass=kilogram per meter(kg/m) 10．粘度——秒/升Viscosity=second per litre(s/L)11．排量——m3/min Flow rate=cubic metre per min.(m3/min)12．压力梯度——千帕/米Pressure gradient=kilopascal per metre(kPa/m) 13．屈服点——帕Yield point=pascal(pa),(y. p.)14．塑性粘度——毫帕*秒Plastic viscosity=millipascal second(mPa .s), .) 15．切力—帕Gel strength=pascal(pa)16．大绳完成的功——兆*焦尔Work completed by wire line=megajoule(MJ)17内径和外径——毫米Inside diameter and outside diameter=millimetre(mm)18．泵压——千帕Pump pressure=kilopascal(kpa)19．钻压：指重表以十牛顿记录Weight on bit ; Indicator will record decanewton20．租地Lease21．井号Well No22．井段Well number23．日期Date24．年Yr. 月MO. 日Day25．施工者（单位）Operator26．承包者（单位）Contractor27．钻机编号Rig No.28．施工单位代表签名Signature of operator’s representative29．承包单位队长（技师）签名Signature of contractor’s toolpusher 30．钻杆尺寸（规范）D. P. size31．每米重kg/m32．钢级Grade33．接头外径Tool .34．扣型Type thread35．钻柱号String No.36．泵编号Pump No.37．泵生产厂家Pump manufacturer38．驱动方式Type of drive39．冲程Stroke length40．时效分析—小时Time distribution=hours41．序号Code No.42．工作内容Operation43．早班、Morn.=morning tour 中班、Day=day tour 晚班Eve.=evening tour 44．安装与拆卸Rig up and tear down45．纯钻Drill actual46．扩眼Reaming47．取心Coring48．循环与处理泥浆Condition mud & circulate49．起下钻Trips50．保养钻机Lubricate rig51．检修钻机Repair rig52．倒大绳与滑大绳Cut off drilling line and slip drilling line53．测斜Deviation survey54．吊测Wire line logs55．下套管与固井Run casing and cement56．候凝Wait on cement57．安装防喷器Nipple up 防喷器试压Test 中途测试Drill stem test 60．打水泥塞（固堵）Plug back61．挤水泥Squeeze cement62．打捞Fishing63．定向工作Dir. work64．完井Completion65．射孔Perf’R’T’N(Perforation)66．起下油管TBG Trips67．处理Treating68．抽吸Swabbing69．测试Testing70．其它Addit’N’L71．合计Total72．一天工作摘要（只用于办公室）Day work summary(office use only) 73．组织停工小时HRS. Standby74．总工作天数Total days work75．从开钻起天数No. of days from spud76．累计钻进小时Cumulative rotation HRS77．总泥浆费用Total mud cost78．钻具结构Drilling assembly79．交班时At end of tour80．钻头Bit81．扶正器外径STB .82．扩大器外径RMR OD83．钻铤内径、外径OD84．钻杆立柱数Stands DP85．钻杆单根数Stingles .86．方入Kelly down87．悬重(Force)WT of string daN88．钻头记录Bit record89．钻头编号Bit No.90．钻头尺寸（规范）Bit size91．制造厂家MFG92．型号Type93．喷嘴（毫米）Jets(mm)94．顺序号Ser No.95．起出井深Depth out96．下入井深Depth in97．总进尺Total meters drilled98．使用小时Total HRS run99．压力降（千帕）Pressure drop (kPa)100．泥浆记录Mud record101．时间Time102．失水Water loss(ml)103．pH值pH(potential of hydrogen)104．固含（%）Solids(%)105．泥浆与药品Mud & chemical added106．类型Type、用量AMT、公斤kg107．合法地面图Legal Land Description108．完井套管、油管或尾管Last casing, tubing or liner 109．厂商Made110．总长Total length111．下入深度Set at112．补心高（转盘面至套管头）TO CSG HD113．钢丝绳记录Wire line record114．滚筒号Reel No.115．尺寸（规范）Size116．股数No. lines117．滑动米数Meters slipped118．倒掉米数Meters cut off119．现存长度Present length120．从...到... from...to...121．钻进（缩写）DR-D 扩眼（缩写）RM-R 取心（缩写）Core-C 122.岩心号Core No.123.地层Formation124.实际岩心收获率Show core recovery125.转盘转速Rotary RPM126.缸套尺寸Liner size127.开泵方式Method run128.单泵S SGL-S 双泵P Par’EL-P 并车C Com’D-C129.测斜记录Deviation Record130.记时Time log131.序号Code No.132.间隔时间Elapsed time133.井斜Dev.134.方位Direction135.井深Depth136.锅炉工作时间Boiler hours137.井队工资表Drilling crew payroll data138.井名及井号Well name & no.139.成员Crew140.技师Toolpusher141.司钻Driller142.架工Derrickman143.机工Motorman144.钻工Floorman145.场地工Roustabout146.机械工长Mechanic147.焊工Welder148.消防员Fireman149.契约人Leaseman150.天数No. of days人身、财产损失报告表内容First Report of Bodily Injury/Property Damage类别Classification2.人身事故Bodily injury财产损失Property damage公司Company地区Division国家Country钻机编号Rig No.监督Supervisor受伤者姓名Name of injured民族（国籍）Nationality社会保险号Social security number地址Address年龄Age性别Sex 男M 女F职业Occupation是否正式工作Regular job 是Yes 否No 每月工资Wages per month在公司工作时间Length of service with co. 所在区域In area本岗位In this job受伤日期Date of injury时间Time开始计算损失时间Date lost time began本班开始时间Time this tour began受伤级别Class of injury致命的Fatal承担责任Restricted duty无时间损失No lost time医生姓名Doctor-name医院名字Hospital-name证明人名字Names of witnesses事情发生经过Describe how accident happened不安全行为Unsafe act不安全条件Unsafe condition财产设备损失情况Property or equipment damaged损伤的原始状况Nature of damage估计维修费用（美元）Estimated cost of repair 防止类似事故发生的预防措施Steps taken or needed to prevent similar accident备注Remarks填表人Prepared by职称Title签字Signed附录四数词、年代与日期的读法分数的读法分数由基数词与序数词组合表示。
常用钻井英语缩写
常用钻井英语缩写常用钻井英语缩写Company Document number：WTUT-WT88Y-W8BBGB-BWYTT-19998钻井英语缩写1.DPdrillpipe钻杆2.HWDPheavyweight(wall)drillpipe加重钻杆3.DCdrillcollar钻铤4.BHAbottomholeassembly井下钻具组合5.STBstabilizer钻杆扶正器6.PNMDCponynon-magneticdrillcollar短无磁钻铤7.SMDCshortnon-magneticdrillcollar短无磁钻铤8.PDMpositivedisplacementmotor螺杆9.BOPblowoutpreventer封井器10.BOPEblowoutpreventerequipment封井器设备11.IBOPinsideblowoutpreventer内防喷工具12.CSGcasing套管13.TBGtubing油管14.JNT/JTjoint单根15.XOcross-over配合接头16.IFinternalflush内平17.FHfullhole贯眼18.REGregular正规19.IUinternalupset内加厚20.EUexternalupset外加厚21.EUEexternalupset外加厚22.IEUinterna l＆externalupset内外加厚23.OHopenhole裸眼24.WOBweightonbit钻压25.RPMrevolutionsperminute转速/分钟26.SPMstrokesperminute冲程/每分钟27.ECDequivalentcirculatingdensity当量泥浆密度28.MTmetricton公制吨29.DSTdrillstemtest钻具测试30.KSkeyseat键槽31.KSWkeyseatwiper键槽清洁器32.STDSstands立柱33.VISviscosity粘度34.PVplasticviscosity塑性粘度35.YPyieldpoint屈服值36.FLfiltrateloss滤失37.WLwaterloss失水/doc/5815443491.html,Dtrueverticaldepth 垂深39.MDmeasureddepth测量井深40.TDtotaldepth总井深41.PBTDplugbacktotaldepth人工井底42.PCSpiece件，个43.KOPkickoffpoint造斜点44.DIRdirection定向45.AZMazimuth方位46.DEVdeviation井斜47.ROPrateofpenetration机械转速48.IDinside-diameter内径49.ODoutsidediameter外径50.FTGfootage进尺51.PPGpoundspergallon（密度）每加仑磅52.PSIpoundspersquareinch磅每平方英尺53.SGLsingle单根54.LPlowpressure低压55.HPhighpressure高压56.H P horsepower马力57.HHPhydraulichorsepower水马力58.HTHPhightemperaturehighpressure高温高压59.ADassistantdriller副司钻60.LCMlostcirculationmaterial堵漏剂61.APIAmericanpetroleuminstitute美国石油协会62.IADCinternationalassociationofdrillingcontractors国际钻井承包商协会/doc/5815443491.html,PCChinanationalpetroleum中国石油天然气总公司64.P/Npartnumber零件型号65.S/Nserialnumber系列号66.N/Wnetweight净重67.G/Wgrossweight毛重68.P/Upickup吊起69.M/Umakeup接上70.L/Dlaydown甩开71.N/Unippleup接上72.N/Dnippledown卸开73.R/Urigup安装74.R/Drigdown拆卸75.WOCwaitoncement候凝76.WOWwaitonwater等水77.WOWwaitonweather等天气78.WOOwaitonorder等指令79.RIHruninhole下钻80.POOHpulloutofhole起钻81.DRdrilling钻进82.DDRdailydrillingreport钻井日报表83.RMreaming扩眼（划眼）84.BRbackream倒划眼85.TOFtopoffish鱼顶86.SXsacks袋87.MWmudweight泥浆密度88.CBUcirculatebottomup循环一周89.TOHtripoutofhole起钻90.MWDmeasurementwhiledrilling随钻测量91.LWDloggingwhiledrilling随钻测井92.POBpersonnelonboard井场人员93.SGspecificgravity比重94.NDTnon-destructivetest无损探伤95.S/Ishutin关井96.PTWpermittowork工作许可97.BPVbackpressurevalve回压凡尔98.DIBPVdropinbackpressurevalve投入式单流阀99.NPneutralpoint中和点100.UPSuninterruptedpowersup ply不间断供电101.RBPretrievablebridgeplug 可取回桥塞102.SICPshutincasingpressure 关井套压103.SIDPPshutindrillpipepressur e关井立压最大允许环空压力105．BHTbottomholetemperature 井底温度井底压力液柱压力摩擦压力地面压力节流压力容积系数112．DSAdrillingspooladaptor四通转换法兰双头载丝法兰恒定井底压力初始循环压力终了循环压力造斜率钻具扶正器应急压井管线扩眼器近钻头牙轮扩眼器钻具牙轮扩眼器123.ＲＣＪＢreversecirculationjunkbasket反循环打捞蓝测卡仪负责人作业前安全会泵冲电子防碰天车泥浆体积计量器国际井控论坛righthand大鼠洞/井底口袋地破试验地破试验地层完整性试验梯形扣长圆扣短圆扣循环清洗井底原始钻台面高度急救处理段重水泥返高水基泥浆油基泥浆挂牌上锁总流到面积马达控制中心148.ＳＡＢＡsuppliedairbreathingapparatus空气呼吸器自给式呼吸器钻杆外涂层&Wwaitandweight等待加重法材料安全数据表焊接式翼片扶正器磁粉探伤电潜泵conductorpipe套压/导管油管与套管环空套管与套管环空升/分钟上扣扭矩最大井眼设计压力近钻头扶正器&Aplugandabandon填井、弃井slowcirculatingrate可控硅房/低泵冲作业安全分析下放安全工作载荷顶驱体积压井法定向司钻上半封闸板下半封闸板Anotapplicable不适用的罐度桶秒分钟小时浮箍浮鞋分级箍水泥，固井英尺英寸=pound磅升千磅重量190.@at在……位置全开式安全阀高粘低粘桶每小时压力梯度接箍泥包尽早,safetyandenvironment健康，安全和环保安全工作许可冷作业许可关闭热作业许可用电许可。
石油钻井常用词汇及缩写汇总
石油钻井常用词语及缩写汇总标准钻井日报表内容Official Daily Report Form钻井日报表Daily drilling report2．报表号Report No.3．图例（说明）Legend4．公制度量标准Metric expressions5．所有长度均采用米制，并取两位小数All lengths expressed in metres to two decimal places6．泥浆密度——kg/m3 Mud density = kilogram per cubic meter (kg/m3)7．泥浆泵冲程mm pump-stroke length=millimetre(mm)8．悬重——十牛顿Weight of string=deca newton(daN)9．单位长度质量——kg/m Linear mass=kilogram per meter(kg/m)10．粘度——秒/升Viscosity=second per litre(s/L)11．排量——m3/min Flow rate=cubic metre per min.(m3/min)12．压力梯度——千帕/米Pressure gradient=kilopascal per metre(kPa/m) 13．屈服点——帕Yield point=pascal(pa),(y. p.)14．塑性粘度——毫帕*秒Plastic viscosity=millipascal second(mPa .s), .) 15．切力—帕Gel strength=pascal(pa)16．大绳完成的功——兆*焦尔Work completed by wire line=megajoule(MJ) 17内径和外径——毫米Inside diameter and outside diameter=millimetre(mm) 18．泵压——千帕Pump pressure=kilopascal(kpa)19．钻压：指重表以十牛顿记录Weight on bit ; Indicator will record decanewton 20．租地Lease21．井号Well No22．井段Well number23．日期Date24．年Yr. 月MO. 日Day25．施工者（单位）Operator26．承包者（单位）Contractor27．钻机编号Rig No.28．施工单位代表签名Signature of operator’s representative29．承包单位队长（技师）签名Signature of contractor’s toolpusher30．钻杆尺寸（规范）D. P. size31．每米重kg/m32．钢级Grade33．接头外径Tool .34．扣型Type thread35．钻柱号String No.36．泵编号Pump No.37．泵生产厂家Pump manufacturer38．驱动方式Type of drive39．冲程Stroke length40．时效分析—小时Time distribution=hours41．序号Code No.42．工作内容Operation43．早班、Morn.=morning tour 中班、Day=day tour 晚班Eve.=evening tour 44．安装与拆卸Rig up and tear down45．纯钻Drill actual46．扩眼Reaming47．取心Coring48．循环与处理泥浆Condition mud & circulate49．起下钻Trips50．保养钻机Lubricate rig51．检修钻机Repair rig52．倒大绳与滑大绳Cut off drilling line and slip drilling line53．测斜Deviation survey54．吊测Wire line logs55．下套管与固井Run casing and cement56．候凝Wait on cement57．安装防喷器Nipple up 防喷器试压Test 中途测试Drill stem test 60．打水泥塞（固堵）Plug back61．挤水泥Squeeze cement62．打捞Fishing63．定向工作Dir. work64．完井Completion65．射孔Perf’R’T’N(Perforation)66．起下油管TBG Trips67．处理Treating68．抽吸Swabbing69．测试Testing70．其它Addit’N’L71．合计Total72．一天工作摘要（只用于办公室）Day work summary(office use only) 73．组织停工小时HRS. Standby74．总工作天数Total days work75．从开钻起天数No. of days from spud76．累计钻进小时Cumulative rotation HRS77．总泥浆费用Total mud cost78．钻具结构Drilling assembly79．交班时At end of tour80．钻头Bit81．扶正器外径STB .82．扩大器外径RMR OD83．钻铤内径、外径OD84．钻杆立柱数Stands DP85．钻杆单根数Stingles .86．方入Kelly down87．悬重(Force)WT of string daN88．钻头记录Bit record89．钻头编号Bit No.90．钻头尺寸（规范）Bit size91．制造厂家MFG92．型号Type93．喷嘴（毫米）Jets(mm)94．顺序号Ser No.95．起出井深Depth out96．下入井深Depth in97．总进尺Total meters drilled98．使用小时Total HRS run99．压力降（千帕）Pressure drop (kPa)100．泥浆记录Mud record101．时间Time102．失水Water loss(ml)103．pH值pH(potential of hydrogen)104．固含（%）Solids(%)105．泥浆与药品Mud & chemical added106．类型Type、用量AMT、公斤kg107．合法地面图Legal Land Description108．完井套管、油管或尾管Last casing, tubing or liner109．厂商Made110．总长Total length111．下入深度Set at112．补心高（转盘面至套管头）TO CSG HD113．钢丝绳记录Wire line record114．滚筒号Reel No.115．尺寸（规范）Size116．股数No. lines117．滑动米数Meters slipped118．倒掉米数Meters cut off119．现存长度Present length120．从...到... from...to...121．钻进（缩写）DR-D 扩眼（缩写）RM-R 取心（缩写）Core-C 122.岩心号Core No.123.地层Formation124.实际岩心收获率Show core recovery125.转盘转速Rotary RPM126.缸套尺寸Liner size127.开泵方式Method run128.单泵S SGL-S 双泵P Par’EL-P 并车C Com’D-C129.测斜记录Deviation Record130.记时Time log131.序号Code No.132.间隔时间Elapsed time133.井斜Dev.134.方位Direction135.井深Depth136.锅炉工作时间Boiler hours137.井队工资表Drilling crew payroll data138.井名及井号Well name & no.139.成员Crew140.技师Toolpusher141.司钻Driller142.架工Derrickman143.机工Motorman144.钻工Floorman145.场地工Roustabout146.机械工长Mechanic147.焊工Welder148.消防员Fireman149.契约人Leaseman150.天数No. of days人身、财产损失报告表内容First Report of Bodily Injury/Property Damage类别Classification2.人身事故Bodily injury财产损失Property damage公司Company地区Division国家Country钻机编号Rig No.监督Supervisor受伤者姓名Name of injured民族（国籍）Nationality社会保险号Social security number地址Address年龄Age性别Sex 男M 女F职业Occupation是否正式工作Regular job 是Yes 否No 每月工资Wages per month在公司工作时间Length of service with co.所在区域In area本岗位In this job受伤日期Date of injury时间Time开始计算损失时间Date lost time began本班开始时间Time this tour began受伤级别Class of injury致命的Fatal承担责任Restricted duty无时间损失No lost time医生姓名Doctor-name医院名字Hospital-name证明人名字Names of witnesses事情发生经过Describe how accident happened不安全行为Unsafe act不安全条件Unsafe condition财产设备损失情况Property or equipment damaged损伤的原始状况Nature of damage估计维修费用（美元）Estimated cost of repair 防止类似事故发生的预防措施Steps taken or needed to prevent similar accident备注Remarks填表人Prepared by职称Title签字Signed附录四数词、年代与日期的读法分数的读法分数由基数词与序数词组合表示。
钻井缩写大全
1.OH open hole裸眼2.FH full hole 满眼，贯眼at full speed3.AD assistant driller 副司钻4.NTP （N toolpusher）night toolpusher夜班队长5.RM reaming 划眼rig manager 平台经理6.Back RM back ream倒划眼7.CSG casing 套管8.TBG tubing 油管coiled tubing9.REG regular 常规扣at regular intervals regular meeting, irregular meeting10.FTG footage 进尺11.FPH footage per hour 每小时进尺12.SNG single 单根13.Hrs. hours14.Yest. Yesterday15.Fin. Finish 完成16.OBS observe 观察17.w/, t/, F/ with, to, from18.XO crossover joint/sub 配合接头19.BOP blowout preventer 防喷器20.IBOP inner BOP 内防喷器21.TDS Top drive system 顶驱22.TOF top of fish 鱼顶23.HHP hydraulic horse power 水马力 B.HHP24.Hi-vis high viscosity 高粘25.RPM revolution per minute 转速26.SPM strokes per minute泵冲数stroke length27.ROP rate of penetration 机械钻速TV closed-circuit television29.MWD measuring while drilling 随钻测量30.DP drill pipe 钻杆31.HWDP heavy wall/weight drill pipe 加重钻杆32.DC drill collar 钻铤33.NMDC non-magnetic drill collar 无磁钻铤34.STB stabilizer 扶正器35.JNT joint 单根36.IF internal flush 内平扣Internal-external inner-outer inside-outside Input-output entrance-exit inlet-outlet Indoors-outdoorsIncrease- decrease raise-lower upper-lower37.IU internal upset 内加厚38.EU external upset 外加厚39.IEU internal & external upset 内外加厚40.WOB weight on bit 钻压bit load41.ECD equivalent circulating density 当量循环密度42.BHA bottom hole assembly 底部钻井组合43.DST drill stem test中途测试44.KOP kick off point 造斜点45.KS keyseat 键槽46.STDS stands 立柱47.VIS viscosity 粘度48.WL water loss 失水wireline电线49.PV plastic viscosity 塑粘50.FL filtrate loss 滤失51.TD total depth 总井深D true vertical depth 垂深53.MD measured depth测深54.DIR direction 定向55.DD directional driller 定向井司钻56.DDR daily drilling report 钻井日报57.AZM(AZI) azimuth 方位角58.DEV deviation 井斜59.INC. inclination井斜incomplete 未完成60.ID inside diameter 内径61.OD outside diameter 外径62.PPG pound per gallon 磅每加仑63.LCM lost circulation material 堵漏材料64.P/N part number 零件号65.S/N serial number 序列号66.N/W net weight 净重67.G/W gross weight 毛重68.P/t pressure test 试压69.P/u pick up 上扣70.M/u make up 上扣71.B/o back off 卸扣72.L/d lay down 甩单根73.N/u nipple up 安装（防喷器，采油树）74.N/d nipple down 拆卸（防喷器，采油树）75.R/u rig up安装76.R/d rig down 拆卸77.WOC wait on cement 候凝78.RIH run in hole 下钻79.POOH pull out of hole 起钻80.DRG drilling 钻进81.WOW wait on water 等水82.SX sacks 袋83.MW mud weight 泥浆比重84.CBU circulation bottom up 底部循环一周85.YP yield point 屈服值，动切力86.NP neutral point 中和点87.Gel 静切力88.HTHP high temperature high pressure 高温高压89.PPE personal protective equipment 劳保90.PDM positive displacement motor 螺杆，容积式马达91.TFA total flow area 总流量面积92.BHP bottom hole pressure 井底压力93.MAASP maximum allowable annulus safety pressure 最大允许环空压力94.SIDPP shut-in drill pipe pressure 关井立压95.SICP shut-in casing pipe 关井套压96.SPP standpipe pressure 立管压力97.HP high pressure 高压hydrostatic pressure 静液柱压力horsepower 马力98.DLS dog leg severity 狗腿严重度severe99.LOT leak off test 漏失试验100.LTI lost time injured 工伤损耗101.LTA last time accident 上一次事故102.HCR hydraulic control remote 远程液控103.FIT formation integrity test 地破压力测试104.NDT non-destruction test 无损探伤105.LPR lower pipe ram 下半封闸板106.UPR upper pipe ram 上半封闸板107.MUT make up torque 上扣扭矩108.RKB rotary kelly bushing 磙子方补心109.RPSP reduced pump stroke pressure 低泵速压力110.Shut-in wellhead & shut in pressure 关井压力111.SSSV sub-surface safety valve 井下安全阀112.SPP standpipe pressure 立柱压力113.CP casing pressure 套压conduct pipe 导管114.WC water content 含水water cut 水侵115.LP low pressure 低压116.WOO wait on order 待命117.LWD logging while drilling 随钻测井118.PTW permit to work 工作许可119.BPV back pressure valve 回压凡尔120.NP non-programmed 设计外的，计划外的121.BHT bottom hole temperature 井底温度122.PF 摩擦系数123.DSA double studded adapter 双栽丝法兰，双螺栓法兰124.ICP initial circulating pressure 初始循环压力125.BUR build up rate 造斜率126.RMR reamer 划眼器127.PIC person in charge 负责人128.PJSM pre-job safety meeting 工作前安全会129.STK stroke 冲数130.RH rat hole 大鼠洞131.BTC buttress thread connection 梯型扣132.LTC long thread connection 长圆扣133.STC short thread connection 短圆扣134.CHC circulate hole clean 循环清洗井底135.TOC top of cement 水泥返高136.PBTD plug back total depth 人工井底137.WBM water-based mud 水基泥浆138.OBM oil-based mud 油基泥浆139.LO/TO lock-out/tag-out 锁定牌（维修中）140.SABA supplied air breathing apparatus 空气呼吸器141.MSDS material safety data sheet 材料安全数据表142.MPI magnetic particle inspection 磁粉探伤143.ESP electric submersible pump 电潜泵144.TCA tubing and casing annulus 油套环空A casing and casing annulus 套管与套管环空146.NBS near-bit stabilizer 近钻头扶正器147.P&A plug and abandon 填井，弃井148.JSA job safety analysis 工作安全分析149.SO slack off 下放遇阻150.SWL safety working load 安全工作负荷151.N/A non-applicable 不适用的152.Torq. torque 扭矩153.bbl barrel 桶154.F/C float collar 浮箍155.F/v float valve 浮阀156.F/S float shoe 浮鞋157.CMT cement 固井158.WT weight 重量159.BPH barrel per hour 桶每小时160.PG pressure gradient 压力梯度161.BU balled up 泥包162.QHSE quality health safety evironment 163.CWP cold work permit 冷作业许可164.HWP hot work permit 热作业许可165.EWP electric work permit 电作业许可166.SD shut down 关闭sand 含砂167.JB junk basket 打捞杯168.EST estimate 评估169.CUM cumulated 累积的170.SS shock sub 减震器171.NPC non-magnetic pony collar 无磁短钻铤172.ASSY assembly 总成173.CONN connect 连接174.BTM bottom 底部175.PKR 封隔器176.RSS rotary steerable system 旋转导向系统177.SOW slip on weld 卡瓦焊接式(套管头) 178.LITH lithology 岩性THANKS !!!致力为企业和个人提供合同协议，策划案计划书，学习课件等等打造全网一站式需求欢迎您的下载，资料仅供参考。
常用钻井英语缩写
钻井英语缩写1.DP drill pipe 钻杆2.HWDP heavy weight (wall)drill pipe 加重钻杆3.DC drill collar 钻铤4.BHA bottom hole assembly井下钻具组合5.STB stabilizer 钻杆扶正器6.PNMDC pony non-magneticdrill collar 短无磁钻铤7.SMDC short non-magneticdrill collar 短无磁钻铤8.PDM positive displacementmotor 螺杆9.BOP blowout preventer 封井器10.BOPE blow out preventerequipment 封井器设备11.IBOP inside blowoutpreventer 内防喷工具12.CSG casing 套管13.TBG tubing 油管14.JNT/JT joint 单根15.XO cross-over 配合接头16.IF internal flush 内平17.FH full hole 贯眼18.REG regular 正规19.IU internal upset 内加厚20.EU external upset 外加厚21.EUE external upset 外加厚22.IEU interna l＆externalupset 内外加厚23.OH open hole 裸眼24.WOB weight on bit 钻压25.RPM revolutions per minute转速/分钟26.SPM strokes per minute冲程/每分钟27.ECD equivalent circulatingdensity 当量泥浆密度28.MT metric ton 公制吨29.DST drill stem test 钻具测试30.KS key seat 键槽31.KSW key seat wiper 键槽清洁器32.STDS stands 立柱33.VIS viscosity 粘度34.PV plastic viscosity 塑性粘度35.YP yield point 屈服值36.FL filtrate loss 滤失37.WL water loss 失水D true vertical depth垂深39.MD measured depth 测量井深40.TD total depth 总井深41.PBTD plug back total depth人工井底42.PCS piece 件，个43.KOP kick off point 造斜点44.DIR direction 定向45.AZM azimuth 方位46.DEV deviation 井斜47.ROP rate of penetration 机械转速48.ID inside-diameter 内径49.OD outside diameter 外径50.FTG footage 进尺51.PPG pounds per gallon（密度）每加仑磅52.PSI pounds per square inch磅每平方英尺53.SGL single 单根54.LP low pressure 低压55.HP high pressure 高压56.H P horsepower 马力57.HHP hydraulic horsepower水马力58.HTHP high temperaturehigh pressure 高温高压59.AD assistant driller 副司钻60.LCM lost circulationmaterial 堵漏剂61.API American petroleuminstitute 美国石油协会62.IADC internationalassociation of drilling contractors 国际钻井承包商协会PC China nationalpetroleum 中国石油天然气总公司64.P/N part number 零件型号65.S/N serial number 系列号66.N/W net weight 净重67.G/W gross weight 毛重68.P/U pick up 吊起69.M/U make up 接上70.L/D lay down 甩开71.N/U nipple up 接上72.N/D nipple down 卸开73.R/U rig up 安装74.R/D rig down 拆卸75.WOC wait on cement 候凝76.WOW wait on water 等水77.WOW wait on weather 等天气78.WOO wait on order 等指令79.RIH run in hole 下钻80.POOH pull out of hole 起钻81.DR drilling 钻进82.DDR daily drilling report钻井日报表83.RM reaming 扩眼（划眼）84.BR back ream 倒划眼85.TOF top of fish 鱼顶86.SX sacks 袋87.MW mud weight 泥浆密度88.CBU circulate bottom up循环一周89.TOH trip out of hole 起钻90.MWD measurement whiledrilling 随钻测量91.LWD logging while drilling随钻测井92.POB personnel on board井场人员93.SG specific gravity 比重94.NDT non-destructive test无损探伤95.S/I shut in 关井96.PTW permit to work 工作许可97.BPV back pressure valve回压凡尔98.DIBPV drop in backpressure valve 投入式单流阀99.NP neutral point 中和点100.UPS uninterrupted power supply 不间断供电101.RBP retrievable bridge plug 可取回桥塞102.SICP shut in casing pressure 关井套压103.SIDPP shut in drill pipe pressure 关井立压104.MAASP maximum allowable annular surface pressure 最大允许环空压力105．BHT bottom hole temperature 井底温度106.BHP bottom hole pressure 井底压力107.HP hydrostatic pressure 液柱压力108. FP friction pressure 摩擦压力109. SP surface pressure 地面压力110. CP choke pressure 节流压力111.CF capacity factor 容积系数112．DSA drilling spool adaptor 四通转换法兰113. DSA double studded adaptor 双头载丝法兰114. CBHP constant bottom hole pressure 恒定井底压力115. ICP initial circulating pressure 初始循环压力116. FCP.final circulating pressure 终了循环压力117. BUR. build up rate 造斜率118. SS string stabilizer 钻具扶正器119. EMKL emergency kill line 应急压井管线120. RMR reamer 扩眼器121. NBRR near-bit roller reamer 近钻头牙轮扩眼器122. SR string roller reamer 钻具牙轮扩眼器123.ＲＣＪＢreverse circulation junk basket 反循环打捞蓝124. FPI free point indicator 测卡仪125. PIC person in charge 负责人126. PJSM pre-job safety meeting 作业前安全会127. STK stroke 泵冲128. ACS automatic crown saver 电子防碰天车129. PVT pit volume totalizer 泥浆体积计量器130. IWCF international well control forum 国际井控论坛131. RH rat hole / right hand 大鼠洞/ 井底口袋132. LOT leak off test 地破试验133. PIT pressure integrity test 地破试验134. FIT formation integrity test 地层完整性试验135. BTC buttress thread connection 梯形扣136. L TC long thread connection 长圆扣137. STC small thread connection 短圆扣138. CHC circulate hole clean 循环清洗井底139. ODF original drill floor 原始钻台面高度140. FA T first aid treatment 急救处理141. PPF pound per foot 段重142. TOC top of cement 水泥返高143. WBM water base mud 水基泥浆144. OBM oil base mud 油基泥浆145. LOTO lock out tag out 挂牌上锁146. TFA total flow area 总流到面积147. MCC motor control center 马达控制中心148.ＳＡＢＡsupplied air breathing apparatus 空气呼吸器149.SCBA self-contained breathing apparatus 自给式呼吸器150.EPC external pipe coating 钻杆外涂层151.W&W wait and weight 等待加重法152.MSDS material safety data sheet 材料安全数据表153.WBS weld blade stabilizer 焊接式翼片扶正器154.MPI magnetic particle inspection 磁粉探伤155.ESP electric submersible pump 电潜泵156.CP casing pressure/conductor pipe 套压/导管157.TCA tubing and casing annulus 油管与套管环空A casing and casingannulus 套管与套管环空159.LPM liter per minute 升/分钟160.MUT make up torque 上扣扭矩161.MWDP maximum well design pressure 最大井眼设计压力162.NBS near bit stabilizer 近钻头扶正器163.P&A plug and abandon 填井、弃井164.SCR silicon control rectifier/slow circulating rate 可控硅房/低泵冲165.JSA job safety analysis 作业安全分析166.SO slack off 下放167.SWL safe working load 安全工作载荷168.TDS top drive system 顶驱169.VM volumetric method 体积压井法170.DD directional driller 定向司钻171.UPR upper pipe ram 上半封闸板172.LPR lower pipe ram 下半封闸板173.N/A not applicable 不适用的 tank 罐175.DEG degree 度176.bbl barrel 桶177.sec second 秒178.Min minute 分钟179.Hr hour 小时180.FC float collar 浮箍181.FS float shoe 浮鞋182.DVT 分级箍183.CMT cement 水泥，固井184.ft foot 英尺184.in inch 英寸186.lb libra=pound 磅187.L liter 升188.klb kilo-pound 千磅189.WT weight 重量190.@ at 在……位置191.FOSV full opening safety valve 全开式安全阀192.HV high viscosity 高粘193.LV low viscosity 低粘194.BPH barrel per hour 桶每小时195.PG pressure gradient 压力梯度196.CPLG coupling 接箍197.BU balled up 泥包198.ASAP as soon as possible 尽早199.HSE health ,safety and environment 健康，安全和环保201.PA public announcement 202.SWP safety work permit 安全工作许可203.LWP life work permit 204.CWP cold work permit 冷作业许可205.SD shut down 关闭206.CSE confined space entry 207.HWP hot work permit 热作业许可208.EWP electrical work permit 用电许可。
钻井缩写大全
1.OH open hole裸眼2.FH full hole 满眼，贯眼at full speed3.AD assistant driller 副司钻4.NTP（N toolpusher）night toolpusher夜班队长5.RM reaming 划眼rig manager 平台经理6.Back RM back ream倒划眼7.CSG casing 套管8.TBG tubing 油管coiled tubing9.REG regular 常规扣at regular intervalsregular meeting, irregular meeting10.FTG footage 进尺11.FPH footage per hour 每小时进尺12.SNG single 单根13.Hrs. hours14.Yest. Yesterday15.Fin. Finish 完成16.OBS observe 观察17.w/, t/, F/ with, to, from18.XO crossover joint/sub 配合接头19.BOP blowout preventer 防喷器20.IBOP inner BOP 内防喷器21.TDS Top drive system 顶驱22.TOF top of fish 鱼顶23.HHP hydraulic horse power 水马力 B.HHP24.Hi-vis high viscosity 高粘25.RPM revolution per minute 转速26.SPM strokes per minute泵冲数stroke length27.ROP rate of penetration 机械钻速TV closed-circuit television29.MWD measuring while drilling 随钻测量30.DP drill pipe 钻杆31.HWDP heavy wall/weight drill pipe 加重钻杆32.DC drill collar 钻铤33.NMDC non-magnetic drill collar 无磁钻铤34.STB stabilizer 扶正器35.JNT joint 单根36.IF internal flush 内平扣upper-lower37.IU internal upset 内加厚38.EU external upset 外加厚39.IEU internal & external upset 内外加厚40.WOB weight on bit 钻压bit load41.ECD equivalent circulating density 当量循环密度42.BHA bottom hole assembly 底部钻井组合43.DST drill stem test中途测试44.KOP kick off point 造斜点45.KS keyseat 键槽46.STDS stands 立柱47.VIS viscosity 粘度48.WL water loss 失水wireline电线49.PV plastic viscosity 塑粘50.FL filtrate loss 滤失51.TD total depth 总井深D true vertical depth 垂深53.MD measured depth测深54.DIR direction 定向55.DD directional driller 定向井司钻56.DDR daily drilling report 钻井日报57.AZM(AZI) azimuth 方位角58.DEV deviation 井斜59.INC. inclination井斜incomplete 未完成60.ID inside diameter 内径61.OD outside diameter 外径62.PPG pound per gallon 磅每加仑63.LCM lost circulation material 堵漏材料64.P/N part number 零件号65.S/N serial number 序列号66.N/W net weight 净重67.G/W gross weight 毛重68.P/t pressure test 试压69.P/u pick up 上扣70.M/u make up 上扣71.B/o back off break out卸扣72.L/d lay down 甩单根73.N/u nipple up 安装（防喷器，采油树）74.N/d nipple down 拆卸（防喷器，采油树）75.R/u rig up安装76.R/d rig down 拆卸77.WOC wait on cement 候凝78.RIH run in hole 下钻79.POOH pull out of hole 起钻80.DRG drilling 钻进81.WOW wait on water 等水82.SX sacks 袋83.MW mud weight 泥浆比重84.CBU circulation bottom up 底部循环一周85.YP yield point 屈服值，动切力86.NP neutral point 中和点87.Gel 静切力88.HTHP high temperature high pressure 高温高压89.PPE personal protective equipment 劳保90.PDM positive displacement motor 螺杆，容积式马达91.TFA total flow area 总流量面积92.BHP bottom hole pressure 井底压力93.MAASP maximum allowable annulus safetypressure 最大允许环空压力94.SIDPP shut-in drill pipe pressure 关井立压95.SICP shut-in casing pipe 关井套压96.SPP standpipe pressure 立管压力97.HP high pressure 高压hydrostaticpressure 静液柱压力horsepower 马力98.DLS dog leg severity 狗腿严重度severe99.LOT leak off test 漏失试验100.LTI lost time injured 工伤损耗101.LTA last time accident 上一次事故102.HCR hydraulic control remote 远程液控103.FIT formation integrity test 地破压力测试104.NDT non-destruction test 无损探伤105.LPR lower pipe ram 下半封闸板106.UPR upper pipe ram 上半封闸板107.MUT make up torque 上扣扭矩108.RKB rotary kelly bushing 磙子方补心109.RPSP reduced pump stroke pressure 低泵速压力110.Shut-in wellhead & shut in pressure 关井压力111.SSSV sub-surface safety valve 井下安全阀112.SPP standpipe pressure 立柱压力113.CP casing pressure 套压conduct pipe 导管114.WC water content 含水water cut 水侵115.LP low pressure 低压116.WOO wait on order 待命117.LWD logging while drilling 随钻测井118.PTW permit to work 工作许可119.BPV back pressure valve 回压凡尔120.NP non-programmed 设计外的，计划外的121.BHT bottom hole temperature 井底温度122.PF 摩擦系数123.DSA double studded adapter 双栽丝法兰，双螺栓法兰124.ICP initial circulating pressure 初始循环压力125.BUR build up rate 造斜率126.RMR reamer 划眼器127.PIC person in charge 负责人128.PJSM pre-job safety meeting 工作前安全会129.STK stroke 冲数130.RH rat hole 大鼠洞131.BTC buttress thread connection 梯型扣132.LTC long thread connection 长圆扣133.STC short thread connection 短圆扣134.CHC circulate hole clean 循环清洗井底135.TOC top of cement 水泥返高136.PBTD plug back total depth 人工井底137.WBM water-based mud 水基泥浆138.OBM oil-based mud 油基泥浆139.LO/TO lock-out/tag-out 锁定牌（维修中）140.SABA supplied air breathing apparatus 空气呼吸器141.MSDS material safety data sheet 材料安全数据表142.MPI magnetic particle inspection 磁粉探伤143.ESP electric submersible pump 电潜泵144.TCA tubing and casing annulus 油套环空A casing and casing annulus 套管与套管环空146.NBS near-bit stabilizer 近钻头扶正器147.P&A plug and abandon 填井，弃井148.JSA job safety analysis 工作安全分析149.SO slack off 下放遇阻150.SWL safety working load 安全工作负荷151.N/A non-applicable 不适用的152.Torq. torque 扭矩153.Bbl barrel 桶154.F/C float collar 浮箍155.F/v float valve 浮阀156.F/S float shoe 浮鞋157.CMT cement 固井158.WT weight 重量159.BPH barrel per hour 桶每小时160.PG pressure gradient 压力梯度161.BU balled up 泥包162.QHSE quality health safety evironment 163.CWP cold work permit 冷作业许可164.HWP hot work permit 热作业许可165.EWP electric work permit 电作业许可166.SD shut down 关闭sand 含砂167.JB junk basket 打捞杯168.EST estimate 评估169.CUM cumulated 累积的170.SS shock sub 减震器171.NPC non-magnetic pony collar 无磁短钻铤172.ASSY assembly 总成173.CONN connect 连接174.BTM bottom 底部175.PKR 封隔器176.RSS rotary steerable system 旋转导向系统177.SOW slip on weld 卡瓦焊接式(套管头) 178.LITH lithology 岩性179.N. VEL nozzle velocity 水眼流速180. A.VEL annular velocity 环空流速181.BS bit sub 接头短接182.LNR liner 尾管183.HGR hanger 悬挂器184.CIP cement in place固井结束185.PBR polished bore receptacle 回接筒。
钻井工程术语类名词解释
9、钻台：装于井架底座上，作为钻工作业的场所。
10、钻具：井下钻井工具的简称。
一般来说，它是指方钻杆、钻杆、钻铤、 接头、稳定器、井眼扩大器、减振器、钻头以及其它井下工具等。
11、方钻杆：用高级合金钢制成的，截面外形呈四方形或六方形而内为圆孔的厚壁管子。
两端有连接螺纹。
主要用于传递扭矩和承受钻柱的重量。
12、钻杆：用高级合金钢制成的无缝钢管。
两端有接头。
用于加深井眼，传递扭矩，并形成钻井液循环的通道。
可分为内平钻杆、管眼钻杆和正规钻杆。
13、钻柱：是指自水龙头以下钻头以上钻具管串的总称。
由方钻杆、钻杆、 钻铤、接头、稳定器等钻具所组成。
14、小鼠洞：位于井口的正前方，用于预先放置钻杆单根的洞，以加快接单根操作。
15、（大）鼠洞：当不使用方钻杆而从大钩上卸下时，用于放置方钻杆和水龙 头的洞，位于钻台左前方井架大腿与井口的连线上。
16、下部钻具组合：指最下部一段钻柱的组成。
17、井眼轴线：井眼的中心线。
18、井口工具：钻台上用于井口操作的工具。
包括大钳（吊钳）、吊卡、卡瓦、 安全卡瓦、提升短节、钻头装卸器、旋接器等。
19、指重表：反映大钩上载荷变化情况的仪表，它可显示悬重、钻重和钻压。
20、单根：指一根钻杆。
21、双根：指连成一体的两根钻杆。
22、立柱（立根）：起钻时卸成一定长度，能立在钻台的钻杆盒上的一柱钻柱。
一般为三根钻杆。
23、吊单根：将钻杆单根吊起放入小鼠洞内的操作。
24、接单根：当钻完方钻杆的有效长度时，将一根钻杆接到井内钻柱上使之加长的操作。
钻井工程常用术语（一） 1、井场： 2、井口： 3、井底： 4、井壁： 6、裸眼： 7、环空： 柱状空间。
钻井施工必需的作业场地。
井的开口端。
井的底端。
井眼的圆柱形表面。
未下套管部分的井段井壁。
井中下有管柱时，井壁与管柱或管柱与管柱之间的圆环形截面的8、 井：为便于安装井控装置开挖的圆或方形井。
25、钻井工序：指钻井工艺过程的各个组成部分。
一般包括钻前准备、钻进、 取芯、中途 测试、测井、固井和完井等。
钻井缩写大全
1.OHopenhole裸眼2.FHfullhole满眼，贯眼atfullspeed3.ADassistantdriller副司钻4.NTP（Ntoolpusher）nighttoolpusher夜班队长5.RMreaming划眼rigmanager平台经理6.BackRMbackream倒划眼7.CSGcasing套管8.TBGtubing油管coiledtubing9.REGregular常规扣atregularintervalsregularmeeting,irregularmeeting34.STBstabilizer扶正器35.JNTjoint单根36.IFinternalflush内平扣Internal-externalinner-outerinside-outsideInput-outputentrance-exitinlet-outletIndoors-outdoorsIncrease-decreaseraise-lowerupper-lower37.IUinternalupset内加厚38.EUexternalupset外加厚39.IEUinternal&externalupset内外加厚40.WOBweightonbit钻压bitload41.ECDequivalentcirculatingdensity当量循环密度42.BHAbottomholeassembly底部钻井组合43.DSTdrillstemtest中途测试44.KOPkickoffpoint造斜点45.KSkeyseat键槽46.STDSstands立柱47.VISviscosity粘度48.WLwaterloss失水wireline电线49.PVplasticviscosity塑粘50.FLfiltrateloss滤失76.R/drigdown拆卸77.WOCwaitoncement候凝78.RIHruninhole下钻79.POOHpulloutofhole起钻80.DRGdrilling钻进81.WOWwaitonwater等水82.SXsacks袋83.MWmudweight泥浆比重84.CBUcirculationbottomup底部循环一周85.YPyieldpoint屈服值，动切力86.NPneutralpoint中和点87.Gel静切力88.HTHPhightemperaturehighpressure高温高压89.PPEpersonalprotectiveequipment劳保90.PDMpositivedisplacementmotor螺杆，容积式马达91.TFAtotalflowarea总流量面积92.BHPbottomholepressure井底压力93.MAASPmaximumallowableannulussafetypressure最大允许环空压力94.SIDPPshut-indrillpipepressure关井立压95.SICPshut-incasingpipe关井套压96.SPPstandpipepressure立管压力100.101.102.103.104.105.106.107.108.109.110.111.112.113.114.115.116.117.118.119.120.121.122.PF摩擦系数123.DSAdoublestuddedadapter双栽丝法兰，双螺栓法兰124.ICPinitialcirculatingpressure初始循环压力125.BURbuilduprate造斜率126.RMRreamer划眼器127.PICpersonincharge负责人128.PJSMpre-jobsafetymeeting工作前安全会129.STKstroke冲数130.RHrathole大鼠洞131.BTCbuttressthreadconnection梯型扣132.LTClongthreadconnection长圆扣133.STCshortthreadconnection短圆扣134.CHCcirculateholeclean循环清洗井底135.TOCtopofcement水泥返高136.PBTDplugbacktotaldepth人工井底137.WBMwater-basedmud水基泥浆138.OBMoil-basedmud油基泥浆139.LO/TOlock-out/tag-out锁定牌（维修中）140.SABAsuppliedairbreathingapparatus空气呼吸器141.MSDSmaterialsafetydatasheet材料安全数据表142.MPImagneticparticleinspection磁粉探伤143.144.145.146.147.148.149.150.151.152.153.154.155.156.157.158.159.160.161.162.163.164.165.166.167.168.ESTestimate评估169.CUMcumulated累积的170.SSshocksub减震器171.NPCnon-magneticponycollar无磁短钻铤172.ASSYassembly总成173.CONNconnect连接174.BTMbottom底部175.PKR封隔器176.RSSrotarysteerablesystem旋转导向系统177.SOWsliponweld卡瓦焊接式(套管头)178.LITHlithology岩性179.。
钻井日志中常用的缩写词
钻井日志中常用的缩写词AbbreviationDP Drill pipe 钻杆HWDP heavy weight drill pipe 加重钻杆DC drill collar 钻铤STB stabilizer 钻杆扶正器SMDC short magnetic drill collar 短无磁钻铤PDM positive displacement motor 螺杆NMDC nonmagnetic drill collar 无磁钻铤（钻具）BOP blowout preventer 封井器CSC casing 套管JNT joint 单根XO cross-over 配合接头IF internal flush 内平FH full hole 贯眼REG regular 正规IU internal upset 内加厚EU external upset 外加厚IEU internal & external upset 内外加厚OH open hole 裸眼WOB weight on bit 钻压RPM revolutions per minute 转速分钟SPM strokes per minute 冲程每分钟ECD equivalent circulating density 当量泥浆密度MT metric ton 公制吨BHA bottom hole assembly 底部钻具组合DST drill stem test 钻具测试KS key seat 键槽STDS stands 立柱VIS viscosity 粘度WL water loss 失水PV plastic viscosity 塑性粘度YP yield point 屈服值FL filtrate loss 滤失TVD true vertical depth 垂深MD measured depth 测量井深TD total depth 总井深KOP kick off point 造斜点DIR direction 定向AZM azimuth 方位DEV deviation 井斜ROP rate of penetration 机械钻速ID inside-diameter 外径FTG footage 进尺PPG pounds per gallon （密度）每加仑磅PSI pounds per square inch 每平方英寸磅SGL single 单根HTHP high temperature high pressure 高温高压AD assistant driller 副司钻LCM lost circulation material 堵漏剂API American petroleum institute 美国石油协会IADC International association drilling contractor 国际钻井承包商CNPC China national petroleum company 中国石油天然气总公司ASAPP/N part number 零件型号S/N serial number 系列号N/W net weight 净重G/W gross weight 毛重P/U pick up 吊起M/U make up 接上L/D lay down 甩开N/U nipple up 接上N/D nipple down 卸开R/U rig up 安装WOC wait on cement 侯凝RIH run in hole 下钻WOO wait on order 等指令POOH pull out of hole 起钻DR drilling 钻进RM reaming 扩眼（划眼）WOW wait on water 等水TOF top of fish 鱼顶SX sacksMW mud weight 泥浆密度CBU circulate bottoms up 循环一周TOH trip out of hole 起钻MWD measurement while drilling 随钻测量KSW key seat wiper 键槽TD-True depth 实际井深，total depth 总进尺，总深度USG-united states gallon 美制加仑Hrs-hours 小时Drlg-drilling 钻进Circ-circulating 循环Hi-Vis—high viscosity 高粘度CSG-casing 套管POOH-pull out of hole 起钻R/U-Rig-up 安装SXS-sacks 袋子WOC-wait on cement 候凝MW-mud weight 泥浆密度N/U-nipple up 安装P/U-pick up 连接，接上，拉起来，上提TIH-trip in hole 下钻Cmt-cement 水泥DCS-drill collar stem 钻铤立柱ISF-induction spherically focused log 感应-球形聚焦测井LSS-long space sonic（log）长源距声波测井GR-gamma ray log 自然伽马测井LCST-lower critical solutions temperatuer 低临界溶液温度R/D-Rig down 拆卸（钻井）设备N/D-nipple down 拆下来，拆卸BOPs-blowout preventer stack 防喷器组合结构M/U-make-up 上扣，连接，组成，安装，组装BHA-bottom hole assemblies 下部钻具组合PV-plastic viscosity 塑性粘度YP-yield point 屈服点，流动点Sols-solids 固相含量PH-acidity or alkalinity 酸碱度Cond-conditioned 调整，处理LOT-leak-off test 地层抗破强度试验，套管鞋下破裂压力试验EMW-equivalent mud weight 当量钻井液密度ROP-rate of penetration 机械钻速fph-feet per hour 每小时进尺wl-water loss 失水B/U bring up 暂停，使停止，中断KCL-potassium chlorine 氯化钾stds-stands 钻杆立柱JB-junk basket 随钻打捞杯L/D-lay down 卸下，甩掉，放下RIH-run in hole 下钻Globe basket 牙轮打捞杯Jts-joints 单根bttm(btm)-bottom 井底，底部wt-weight 钻压DLL-dual laterolog 双侧向测井NGT-natural gamma ray spectroscopy tool 自然伽马能谱测井LDT-litho-density tool 岩性密度测井HDT-hight-resolution dipmeter tool 高分辨率地层倾角测井MSFL-micro-spherically focused log 微球形聚焦测井CNL-compensated neutron（porosity）log 补偿中子（孔隙度）测井RFT-repeat-formation tester 重复式地层测试器WST-well seismic tool 井场地震仪Fin-finish 结束。
常用钻井英语缩写
常用钻井英语缩写 Prepared on 24 November 2020钻井英语缩写1.DPdrillpipe钻杆2.HWDPheavyweight(wall)drillpipe加重钻杆3.DCdrillcollar钻铤4.BHAbottomholeassembly井下钻具组合5.STBstabilizer钻杆扶正器6.PNMDCponynon-magneticdrillcollar短无磁钻铤7.SMDCshortnon-magneticdrillcollar短无磁钻铤8.PDMpositivedisplacementmotor螺杆9.BOPblowoutpreventer封井器10.BOPEblowoutpreventerequipment封井器设备11.IBOPinsideblowoutpreventer内防喷工具12.CSGcasing套管13.TBGtubing油管14.JNT/JTjoint单根15.XOcross-over配合接头16.IFinternalflush内平17.FHfullhole贯眼18.REGregular正规19.IUinternalupset内加厚20.EUexternalupset外加厚21.EUEexternalupset外加厚22.IEUinterna l＆externalupset内外加厚23.OHopenhole裸眼24.WOBweightonbit钻压25.RPMrevolutionsperminute转速/分钟26.SPMstrokesperminute冲程/每分钟27.ECDequivalentcirculatingdensity当量泥浆密度28.MTmetricton公制吨29.DSTdrillstemtest钻具测试30.KSkeyseat键槽31.KSWkeyseatwiper键槽清洁器32.STDSstands立柱33.VISviscosity粘度34.PVplasticviscosity塑性粘度35.YPyieldpoint屈服值36.FLfiltrateloss滤失37.WLwaterloss失水Dtrueverticaldepth垂深39.MDmeasureddepth测量井深40.TDtotaldepth总井深41.PBTDplugbacktotaldepth人工井底42.PCSpiece件，个43.KOPkickoffpoint造斜点44.DIRdirection定向45.AZMazimuth方位46.DEVdeviation井斜47.ROPrateofpenetration机械转速48.IDinside-diameter内径49.ODoutsidediameter外径50.FTGfootage进尺51.PPGpoundspergallon（密度）每加仑磅52.PSIpoundspersquareinch磅每平方英尺53.SGLsingle单根54.LPlowpressure低压55.HPhighpressure高压56.H P horsepower马力57.HHPhydraulichorsepower水马力58.HTHPhightemperaturehighpressure高温高压59.ADassistantdriller副司钻60.LCMlostcirculationmaterial堵漏剂61.APIAmericanpetroleuminstitute美国石油协会62.IADCinternationalassociationofdrillingcontractors国际钻井承包商协会PCChinanationalpetroleum中国石油天然气总公司64.P/Npartnumber零件型号65.S/Nserialnumber系列号66.N/Wnetweight净重67.G/Wgrossweight毛重68.P/Upickup吊起69.M/Umakeup接上70.L/Dlaydown甩开71.N/Unippleup接上72.N/Dnippledown卸开73.R/Urigup安装74.R/Drigdown拆卸75.WOCwaitoncement候凝76.WOWwaitonwater等水77.WOWwaitonweather等天气78.WOOwaitonorder等指令79.RIHruninhole下钻80.POOHpulloutofhole起钻81.DRdrilling钻进82.DDRdailydrillingreport钻井日报表83.RMreaming扩眼（划眼）84.BRbackream倒划眼85.TOFtopoffish鱼顶86.SXsacks袋87.MWmudweight泥浆密度88.CBUcirculatebottomup循环一周89.TOHtripoutofhole起钻90.MWDmeasurementwhiledrilling随钻测量91.LWDloggingwhiledrilling随钻测井92.POBpersonnelonboard井场人员93.SGspecificgravity比重94.NDTnon-destructivetest无损探伤95.S/Ishutin关井96.PTWpermittowork工作许可97.BPVbackpressurevalve回压凡尔98.DIBPVdropinbackpressurevalve投入式单流阀99.NPneutralpoint中和点100.UPSuninterruptedpowersup ply不间断供电101.RBPretrievablebridgeplug 可取回桥塞102.SICPshutincasingpressure 关井套压103.SIDPPshutindrillpipepressur e关井立压最大允许环空压力105．BHTbottomholetemperature 井底温度井底压力液柱压力摩擦压力地面压力节流压力容积系数112．DSAdrillingspooladaptor四通转换法兰双头载丝法兰恒定井底压力初始循环压力终了循环压力造斜率钻具扶正器应急压井管线扩眼器近钻头牙轮扩眼器钻具牙轮扩眼器123.ＲＣＪＢreversecirculationjunkbasket反循环打捞蓝测卡仪负责人作业前安全会泵冲电子防碰天车泥浆体积计量器国际井控论坛righthand大鼠洞/井底口袋地破试验地破试验地层完整性试验梯形扣长圆扣短圆扣循环清洗井底原始钻台面高度急救处理段重水泥返高水基泥浆油基泥浆挂牌上锁总流到面积马达控制中心148.ＳＡＢＡsuppliedairbreathingapparatus空气呼吸器自给式呼吸器钻杆外涂层&Wwaitandweight等待加重法材料安全数据表焊接式翼片扶正器磁粉探伤电潜泵conductorpipe套压/导管油管与套管环空套管与套管环空升/分钟上扣扭矩最大井眼设计压力近钻头扶正器&Aplugandabandon填井、弃井slowcirculatingrate可控硅房/低泵冲作业安全分析下放安全工作载荷顶驱体积压井法定向司钻上半封闸板下半封闸板Anotapplicable不适用的罐度桶秒分钟小时浮箍浮鞋分级箍水泥，固井英尺英寸=pound磅升千磅重量190.@at在……位置全开式安全阀高粘低粘桶每小时压力梯度接箍泥包尽早,safetyandenvironment健康，安全和环保安全工作许可冷作业许可关闭热作业许可用电许可。
钻井工程报表常见缩写词
钻井工程报表常见缩写词（Abbreviations）API American Petroleum Institute美国石油学会APL Annulus Pressure Loss环空压力损失AR Automated Roughneck 铁钻工BHA Bottom Hole Assembly底部钻具组合BHP Bottom-Hole Pressure井底压力BHCT Bottom-Hole Circulating Temperature井底循环温度BHST Bottom-Hole Static Temperature井底静止温度BOP Blow Out Preventer防喷器DD Directional Driller定向工程师CDPP Circulating Drill Pipe Pressure钻杆循环压力CSG Casing套管CP Conductor Pipe, Casing Pressure导管，套压CBBL Core Barrels岩心筒DC Drill Collar钻铤DLS Dogleg Severity 狗腿严重度DP Drill Pipe钻杆DM Driller's Method钻井方法DPP, PDP Drill-Pipe Pressure钻杆压力DST Drill Stem Test中途测试ECD Equivalent Circulating Density当量循环密度EMW Equivalent Mud Weight当量泥浆密度Q Flow rate流量EOR Enhanced Oil Recovery 增产ERD Extended Reach Drilling大位移钻井FCP Final Circulating Pressure最终循环压力HP High Pressure高压FIT Formation Integrity Test地层整体测试HSE Health, Safety And Environment HPHT High Pressure High Temperature高温高压ID Inside Diameter内径HWDP Heavy Weight Drill Pipe加重钻杆KOP Kick Off Point造斜点IADC International Association Of Drilling Contractor国际钻井承包商协会ICP Initial Circulating Pressure初始循环压力LTA Lost Time Accident事故损失时间LOT Leak-Off Test漏失试验LCM Lost Circulation Material堵漏材料LPM Liters Per Minute升/分MAASP Maximum Allowable Annular Surface Pressure最小环空地面压力MD Measured Depth测深MSDS Material Safety Data Sheets材料安全数据表MEMW Maximum Equivalent Mud Weight最大泥浆当量密度MPHS Max. Expected Pressure in Next Hole Section下个井眼最大预测压力MUT Make-Up Torque上扣MWD Measurement While Drilling随钻测量MWDP Max. Well Design Pressure井最大设计压力NBS Near Bit Stabilizer近钻头稳定器NMDC Non Magnetic Drill Collars无磁钻铤NSTK Number Of Pump Strokes泵冲OBM Oil Based Mud油基泥浆OD Outside Diameter外径OE Open Ended 裸眼完钻OH Openhole裸眼P&A lug and Abandon打塞报废PDC Polycrystalline Diamond Compact聚晶金刚石钻头PDM Positive Displacement Motor螺杆PM Preventive Maintenance预防保养POAF Pack-Off Adapter Flange封隔法兰POOH Pull Out Of Hole起钻PPE Personal Protective Equipment个人防护设备（劳保）PV Plastic Viscosity塑性粘度PVT Pit Volume Total 泥浆池总量R/D Rig Down放井架R/U Rig Up 立井架RCD Residual Current Device漏电断路器RIH Run In Hole下钻RFT Repeated Formation Tester地层测试RKB Rotary Kelly Bushings方补心ROP Rate Of Penetration钻速RPM Rotation Per Minute转速RPSP Reduced Pump Strokes Pressure降低泵冲压力S.G. Specific Gravity比重SD Specific Density比重SCBA Self Contained Breathing Apparatus自主式呼吸器SCR Slow Circulating Pump Pressure 低循环泵压SO Slack-Off 下放钻具SHUT-IN Wellhead Or Shut-In Pressure关井压力TD Total Depth总深度SICP Shut-In Casing Pressure关井套压SPM Stroke Per Minute冲/分SIDPP Shut-In Drill Pipe Pressure关井立压TDS Top Drive System顶驱SJA Safe Job Analysis安全工作分析SPP Stand Pipe Pressure立压SSSV Sub Surface Safety Valve井下安全阀TVD Total Vertical Depth垂深SWL Safe Working Load安全工作载荷WOB Weight On Bit钻压TIP Tie In Point数据连接点（定向造斜时或随钻测井时）TOC Top Of Cement水泥面高度VM Volumetric Method容积法UTM Universal Transverse Mercator统一横墨卡托方格网VSIDPP Virtual Shut-In Drill Pipe Pressure实际关井钻杆压力W&W Wait And Weight Method等待加重法YP Yield Point屈服值WBM Water Based Mud水基泥浆WLL Working Load Limit载荷极限WL Wireline有线，电缆作业, 或者钢丝作业HUD Hold up depth 卡钻井深WOC Wait On Cementing候凝WOM Weight On Mill 磨铣钻压WP Working Pressure 工作压力X/O Cross Over Sub转换接头PKR packer 封隔器assy assembly 工具总成S/L slickline 钢丝作业X-tree christmas tree 采油树DS drilling supervisor 钻井监督JWE junior well engineer 实习工程师IP injured person 受伤人员tbg tubing 油管COG cost of goods 货物成本JO job order 工作记录DT delivery ticket 移交用的单据PT production technologist 采油工程师DP Drill pipe 钻杆HWDP heavy weight drill pipe 加重钻杆JNT joint 单根DC drill collar 钻铤STB stabilizer 钻杆扶正器IF internal flush 内平SMDC short magnetic drill collar 短无磁钻铤FH full hole 贯眼REG regular 正规IU internal upset 内加厚EU external upset 外加厚IEU internal & external upset 内外加厚MT metric ton 公制吨KS key seat 键槽DST drill stem test 钻具测试STDS stands 立柱VIS viscosity 粘度WL water loss 失水PV plastic viscosity 塑性粘度FL filtrate loss 滤失DIR direction 定向AZM azimuth 方位DEV deviation 井斜ROP rate of penetration 机械钻速FTG footage 进尺PPG pounds per gallon(密度)每加仑磅PSI pounds per square inch 每平方英寸磅SGL single 单根AD assistant driller 副司钻P/U pick up 吊起CNPC China national petroleum company 中国石油天然气总公司P/N part number 零件型号S/N serial number 系列号N/W net weight 净重G/W gross weight 毛重M/U make up 接上L/D lay down 甩开N/U nipple up 接上N/D nipple down 卸开R/U rig up 安装RIH run in hole 下钻WOO wait on order 等指令DR drilling 钻进RM reaming 扩眼（划眼）WOW wait on water 等水TOF top of fish 鱼顶MW mud weight 泥浆密度CBU circulate bottoms up 循环一周TOH trip out of hole 起钻KSW key seat wiper 键槽清洁器。
常见钻井缩写及含义
Abbreviations used in the Basic Well DesignAnnulus Pressure WhileAPWDMW Mud WeightDrillingBHA Bottom Hole Assembly MWD Measurement While Drilling BML Below Mud Line OBG Overburden GradientBOP Blow Out Preventer OH Open HolePressure Assisted Drill Pipe CART Cam Actuated Running Tool PADPRTRunning ToolCP Conductor Pipe PDM Positive Displacement Motor CSG Casing POOH Pull Out Of HoleCSGS Critical Static Gel Strength PPG Pore Pressure GradientDC Drill Collar P/U Pick UpDifferential GlobalRIH Run In HoleDGPSPositioning SystemDP Drill Pipe RKB Rotary Kelly BushingDPDynamic Positioning system ROP Rate Of Penetration systemDeepwater Wellhead HighDWHCROV Remotely Operated Vehicle CapacityEquivalent CirculationRRT Running/Retrieving Tool ECDDensityEMW Equivalent Mud Weight SFG Shear Failure GradientFG Fracture Gradient SOBM Synthetic Oil Base MudGE Gel SW Sea WaterHO Hole Opener TD Total DepthHWDP Heavy Weight Drill Pipe TOC Top Of CementIBOP Inside Blow Out Preventer TOL Top Of LinerLCM Lost Circulation Material TVD True Vertical DepthUniversal TransverseL/D Lay Down UTMMercatoreLIH Liner hanger VD Vertical DepthVertical Seismic Profile While LOT Leak Off Test VSP-WDDrillingWear Bushing Running LWD Log While Drilling WBRRTRetrieving ToolMD Measure Depth WGS World Geodetic System MSL Mean Sea Level WH WellheadM/U Make Up WOC Wait On Cement。
钻井地质英文词汇标准缩写
喷出，挤出，喷出的，喷发的
extrusion, extrusive
extr
F
小面，刻面，磨光面
facet
fac
微弱的，不明显的，淡的
faint
fnt
好的，公正的，中等的
fair
fr
断层
fault
flt
中文词义
英文词
英文缩写
动物群
fauna
fna
英尺
feet
ft
长石
feldspar
fld
含铁的，铁质
car
bide
钙
calcium
ca
氯化钙
calcium chloride
cacl
计算，预测，打算
calculate
calc
井径仪
caliper
pr
寒武纪，寒武系
cambrian
cam
四氯化碳
carbon tetrachloride
ccl
碳质的，含碳的
carbonaceous
carb
套管，下套管
casing
D，Dev
斜的，对角线的，对顶的
diagonal
diag
直径
diameter
dia
侵入带直径
diameter of invaded zone
DIZ
差异，区别，不同
difference
dif
有差别的
differential
dfntl
缩减，减少
diminish
dim
位移，移动，置换
displace
displ
bot
漂砾，巨砾，卵石
常用钻井英语缩写
常用钻井英语缩写标准文档钻井英语缩写motor 螺杆9.BOP blowout preventer 1.DP drill pipe 钻杆封井器HWDP heavy weight (wall) 2.10.BOPE drill pipe 加重钻杆blow out preventerequipment 封井器设备3.DC drill collar 钻铤11.IBOP insideblowoutbottom 4.BHA hole assembly井下钻具组合内防喷工具preventer套管casing 12. 5.STB stabilizer 钻杆扶正器CSG油管non-magnetic pony tubing 13.TBG 6.PNMDCdrill collar 单根JNT/JT 短无磁钻铤joint 14. 7.SMDC short 配合接头cross-over 15.non-magnetic XOdrill collar 短无磁钻铤内平internal flush IF 16. 8.PDM 贯眼full hole displacementpositive FH 17.实用大全．标准文档18.REG regular 正规27.ECD equivalent circulatingdensity 当量泥浆密度19.IU internal upset 内加厚28.MT metric ton 公制吨20.EU external upset 外加厚29. DST drill stem test 外加21.EUE external upset 钻具测试厚30.l22.IEU interna＆external KS key seat 键槽31.KSW key seat wiper 内外加厚upset 键槽清洁器裸眼open hole OH 23.32.STDS stands 钻压weight on bit WOB 24.立柱33.VIS viscosity revolutions per minute RPM 25.粘度塑性viscosity 34.PV 分钟/转速plasticstrokes SPM 26. minute per 粘度冲程/屈服值yield point 每分钟YP 35.实用大全．标准文档36.FL filtrate loss 滤失45.AZM azimuth 方位46.water loss 失水DEV deviation 井斜37.WL/doc/282787068.html,D true vertical depth ROP rate of penetration 机械转速垂深48.ID 测量inside-diameter 内径depth 39.MD measured49.井深OD outside diameter 外径50.FTG footage 40.TD total depth 总井深进尺51. plug back total depth PPG pounds per gallon 41.PBTD人工井底（密度）每加仑磅inch pounds per square 52. piece42.PCS 件，个PSIkick 43.KOP 磅每平方英尺off point 造斜点SGL single 单根53. direction DIR 44.低压low pressure 定向LP 54.实用大全．标准文档55.HP high pressure 高压association of drillingcontractors 马力国际钻井承包商56.H horsepower P协会57. HHP hydraulic horsepower/doc/282787068.html,PC China national水马力petroleum 58.HTHP 中国石油天然气high temperature 总公司高温高压high pressure64.P/N part number AD 59.assistant driller 副司零件型号钻65.S/N serial number lost LCM 60.circulation 系列号66.N/W net weight 净重堵漏剂material67.G/W gross weight American API 61.petroleum 毛重68.P/U pick up 美国石油协会institute 吊起接上internationalIADC62. make up M/U 69.实用大全．标准文档70.L/D lay down 甩开80.POOH pull out of hole 起钻71.N/Unipple up 接上81.DR drilling 钻进72.N/D nipple down 卸开82.DDR daily drilling report 73.R/U rig up 安装rig down 拆卸钻井日报表74.R/D扩眼（划眼）on 75.WOC wait cement 候reaming RM 83.倒划眼back ream 84.BR 凝鱼顶top of fish 等水wait on water WOW 85.TOF 76. wait WOW 77.on 袋sacks SX 等weather 86.泥浆密weight 天气mud 87.MW等指on wait 78.WOO order 度up circulate 令CBU 88. bottom run in hole RIH 79. 下钻循环一周实用大全．标准文档89.TOH trip out of hole 起钻97.BPV back pressure valve回压凡尔90.MWD measurement while98.DIBPV drop in back drilling 随钻测量pressure valve drilling 投入式单流阀while 91.LWD logging中和点neutral point NP 99.随钻测井uninterrupted power UPS 100.personnel 92.POB on board井场人员不间断供电supplybridge 93.SG retrievable 101.specific gravity 比重RBPplug test 94.NDT non-destructive 可取回桥塞casing shut in 无损探伤102.SICP95. 关井shut in S/I 关井套压pressurepipe PTW 96.drill shut SIDPP 103.工作work permit to in许可关井立压pressure实用大全．标准文档104.MAASP maximum allowable 110. CP choke pressure 节流压力111.CF capacity factor 容积系数annular surface pressure最大允112．DSA drilling 许环空压力spool adaptor四通转换法兰105．BHT bottom hole temperature113. DSA double 井底温度studded adaptor双头载丝法兰106.BHP bottom hole pressure 井114. CBHP constant 底压力bottom holepressure pressure 恒定井底压力液柱hydrostatic 107.HP115.压力ICPinitialcirculatingpressure friction FP 108. 初始循环压力pressure 摩擦压116. FCP.final circulating pressure 力终了循环压力pressure surface SP 地面压109.造斜率力117. BUR. build up rate实用大全．标准文档118. SS string stabilizer 钻具扶正仪125. PIC person in charge 负责人器126. PJSM pre-job safety meeting line EMKL emergency kill 119.作业前安全会应急压井管线127. STK stroke 120. RMR reamer 扩眼器泵冲128. ACS automatic crown saver roller 121. NBRR near-bit reamer电子防碰天车近钻头牙轮扩眼器129. PVT pit volume 122. SR string roller reamer 钻具totalizer 泥浆体积计量器牙轮扩眼器130. Ｃ123.ＲＪIWCF reverse international well Ｂcontrol forum circulation 反循环打basket junk 国际井控论坛131. RH rat hole / right hand 捞蓝大鼠测卡124. FPI free point indicator 井底口袋/ 洞实用大全．标准文档132. LOT leak off test 地破试验139. ODF original drill floor 原始钻台面高度地133. PIT pressure integrity test140. FAT first aid treatment 急救破试验处理test 134. FIT formation integrity141. PPF pound per foot 地层完整性试验段重142. BTC 135. buttressthreadTOC top of cement 水泥返高梯形扣connection143. WBM water base connection long 136. LTC thread mud 水基泥浆长圆扣144. 137. STC small thread connection OBM oil base mud 油基泥浆短圆扣145. LOTO lock out tag out 挂牌循138. CHC circulate hole clean环清洗井底上锁实用大全．标准文档146. TFA total flow area 总流到152.MSDS material safety data sheet 面积材料安全数据表153.WBS weld blade stabilizer center 焊147. MCC motor control接式翼片扶正器马达控制中心154.MPI magnetic supplied air particleＡ148.ＳＡＢinspection 磁粉探伤breathing apparatus 空气呼吸器155.ESPself-contained149.SCBAelectricsubmersible。