WAGO接线端子选型样本
WAGO(万可)接线端子2273系列操作手册资料
外观
10*16.7*5.8
1000
透明, 导线夹持 部分：白色
14*16.7*5.8
1000
透明, 导线夹持 部分：白色
2273-204 4
18*16.7*5.8
1000
透明, 导线夹持 部分：红色
2273-205 5
22*16.7*5.8
1000
透明, 导线夹持 部分：黄色
2273-206 8
18*16.7*10.4
WAGO（万可）接线端子2273系列操作手册
产品参数
导线横截面积：0.5-2.5mm² AWG线径 ：18-14 额定电压：450V 额定脉冲电压：4KV 额定电流：24A 剥线长度：11mm 适用导线：单股铜导线
污染等级：2
产品型号
型号 2273-202
2273-203
线孔 2
3
外形尺寸（mm） 包装数量
刀将支架内的夹持滑块推到所需宽度。 在固定支架上，连接器可以使用862-482跨接器进行纵向跨接。但请注意：跨接器安 装之后不可再拆下。
操作说明
查看接线情况：透明外壳可显示出导线是否完全插入；外壳彩色部位带有的小窗
口可方便查看导线剥线是否恰当。若窗口中看不到裸露的铜线，则说明导线剥线正确。
操作说明
500
透明, 导线夹持 部分：白色
2273-500
（固定支架）
适于单排(14mm)和双排 50
(18.5mm)连接器
橙色
操作说明
接线操作：剥去单股导线绝缘外皮11 mm，完右转动连接器即可将导线拔出
操作说明
固定支架：调整固定支架宽度：插入5.5mm螺丝刀解开锁定装置，然后转动螺丝
光密封HP Avago兼容连接器技术数据表说明书
Step-by-Step Plastic Cable Connectoring InstructionsThe following step-by-step guide describes how to terminate plasticfiber optic cable. It is ideal for both field and factory installation.Connectors can be easily installed on cable ends with wire strippers,cutters and crimping tool.Finishing the cable is accomplished with the FiberFin HP Polishing Kit, consisting of a Polishing Fixture, 600 grit abrasive paper and 3 μm pink lapping film (3M Company OC3-14). The connector can be used immediately after polishing.Materials needed for plastic fiber termination are:1.Agilent Plastic Optical Fiber Cable (Example: HFBR-RUS500, HFBR-RUD500,HFBR-EUS500, or HFBR-EUD500)Or Mitsubishi Eska® POF Cable2.Industrial Razor Blade or Wire Cutters3.16 Gauge Latching Wire Strippers (Example: Ideal Stripmaster™ type 45-092).4.FF-CRMP-1 Crimping Tool5.FF-LCP-HPPOL-K Polishing Kit6.One of the following Light-Seal connectors:a)FF-LSHP1000-Simplex Friction Connector and Colored StrainReliefb)FF-LSHP1500-Simplex Friction Connector and Colored StrainReliefStep 1When using the duplex connector and duplex cable, the separated duplex cable must be stripped to equal lengths on each cable. This allows easy and proper seating of the cable into the duplex connector; the zip cord structure of the duplex cable permits easy separation of the channels. The channels should be separated approximately 50mm (2.0 in.) back from the ends to permit connectoring and polishing.After cutting the cable to the desired length, strip offapproximately 7mm (0.3 in.) of the outer jacket with the16 gauge wire strippers. Excess webbing on the duplexcable may have to be trimmed to allow the simplex orsimplex latching connector to slide over the cable.Step 2Place the crimp ring and connector over the end of the cable; the fiber should protrude about 3mm (0.12 in.) through the end of the connector. Carefully position the ring so that it is entirely on the connector with the rim of the crimp ring flush with the connector, leaving a small space between the crimp ring and the flange. Then crimp the ring in placewith the crimping tool. One crimp tool is used for all POF connector crimping requirements.For industrial applications or ones that require the best of retention to the cable attachment can be achieved with the use of Patented Light-Seal swage on the nose of the connector (recommended) or the use of a 2 part epoxy part # FF-GMEPXY-1656. The adhesive is placed into the connector prior to insertion of the fiber and the fiber is crimped normally. The connector can be polished after the Patented Light-Seal swage or after the epoxy has cured (Normally 24hours for full cure) and is then ready foruse.Note: By convention, place a gray strain relief on the connector onthe transmitter cable end and the blue strain relief connector in thereceiver cable end to maintain color coding (connectors aremechanically identical).Step 3Any excess fiber protruding from the connector end may be cut off; however, the trimmed fiber should extend at least 1.5 mm (0.06 in.) from the connector end.Insert the connector fully into the polishing fixture with the trimmed fiber protruding from the bottom of the fixture. This plastic polishing fixture can be used to polish two simplex connectors or simplex latching connectors simultaneously, or one duplex connector.Note:The four dots on the bottom of the polishing fixture are wear indicators. Replace the fixture when any dot is no loner visible.Typically, the polishing fixture can be used 10 times; 10 duplex connectors or 20 simplex connectors, two at a time.Place the 600 grit abrasive paper on a flat smooth surface, pressing down on the connector; polish the fiber and the connector using a figure eight pattern of strokes until the connector is flush with the bottom of the polishing fixture. Wipe the connector and fixture with a clean cloth or tissue.Step 4Place the flush connector and polishing fixture on the dull side of the 3 μm pink lapping film and continue to polish the fiber and connector for approximately 25 strokes. The fiber end should be flat, smooth and clean.This cable is now ready for use!Note: Use of pink lapping film finepolishing step results in approximately 2 dBimprovement in coupling performance ofeither a transmitter receiver link or abulkhead/splice over a 600 grit polishalone. This fine polishing step may beomitted where an extra 2 dB of opticalpower is not essential, as with short linklengths. Proper polishing of the tip of thefiber/ connector face results in a tip diameter between 2.5 mm (0.098 in.) minimum and 3.2 mm (0.126 in) maximum. AVAGO REF Part # HFBR-4593 Polishing KitFor Service Call: FiberFin Technical Department 1-630-553-6924 8-5pm CST Email: Technical Questions or Comments to: *****************FiberFin ® and Light-Seal ® are Registered Trademarks of FiberFin, Inc.Copyright© 2021 all Rights Reserved。
浩亭选型指南
21 01 100 9021 21 01 100 9023
母头 (镀银)
09 15 000 6204 09 15 000 6203 09 15 000 6205 09 15 000 6202 09 15 000 6201 09 15 000 6206
母头 (镀银)
09 67 000 7576 09 67 000 5576 09 67 000 8576 09 67 000 3576
Han D® 插针 单独订购
Cat. 6A
Cat. 5
12 6.5 A / 50 V
压接 0.09 … 0.52 mm² 09 10 012 3000 09 10 012 3100 09 10 012 3005 09 10 012 3105 09 10 012 9900 Han® D-Sub 插针
单独订购。 请使用拆卸工具 09 99 000 0346
适用于M12
适用于D-Sub
母插针的定位器 公和母插针的定位器
压接工具 符合 IEC 60352-2标准
09 99 000 0021
09 99 000 0110 09 99 000 0888 09 99 000 0012 09 99 000 0847 09 99 000 0346
插针 / 截面积 [mm²]
09 33 000 6217 09 33 000 6222 09 33 000 6215 09 33 000 6218 09 33 000 6216 09 33 000 6223
09 33 000 6221
插针 / 截面积 [mm²]
D-Sub / 0.09 … 0.82
适用于M12
公插针的定位器
Cat. 6A
插针/线缆 电气数据 数据传输速率 接线 导体的截面积 公插芯 母插芯
接线端子规格大全
宽度F内圆直径E 长度D 内径C 1OT1-3 5.7 3.113.52OT1-47.4 4.115.53OT1-59 5.1174OT1.5-36 3.1145OT1.5-47.1 4.115.46OT1.5-59.2 5.1187OT1.5-610.5 6.1198OT1.5-813.28.1249OT1.5-1015.510.425.510OT1.5-1211OT2.5-37.2 3.114.212OT2.5-47.5 4.11613OT2.5-59.1 5.11814OT2.5-610.7 6.119.215OT2.5-813.38.12416OT2.5-1015.510.42617OT2.5-1218OT4-48 4.11919OT4-59 5.119.220OT4-611.1 6.32221OT4-813.38.225.522OT6-48.1 4.11923OT6-58.3 5.12124OT6-6116.223编号型号插入导线截面前后2-2.55总长 1.2-1.55 2.10.75-151.92.73-46.2 3.24.35-67.1国产圆型裸端头OT25OT6-8148.325.726OT6-101810.43227OT10-613 6.325.528OT10-8158.329.229OT10-101710.332.130OT10-121912.535.831OT16-613.8 6.43032OT16-816.28.330.833OT16-1018.810.535.834OT16-1220.812.539.935OT25-615.8 6.33236OT25-817.88.334.237OT25-1019.510.536.638OT25-1221.812.540.739OT25-1424.114.540.640OT25-1626.516.54441OT35-616 6.333.542OT35-8178.335.543OT35-1019.510.338.344OT35-1221.812.441.545OT35-1424.314.54346OT35-1626.916.546.547OT50-817.58.337.548OT50-1019.510.339.449OT50-122212.442.750OT50-1424.314.54451OT50-1626.916.547.952OT70-818.38.34053OT70-1020.410.44454OT70-1222.412.44755OT70-1424.514.548.556OT70-1627.516.552.557OT95-818.58.343.558OT95-1022.710.348.559OT95-1224.512.549.560OT95-1427.514.553.561OT95-163116.557.580-9520158-108.5 5.6714-1610.560-701813国产叉型裸端头UT20-2512.58.530-3513.59.540-501411.5宽度F 内圆直径E长度D内径C 1UT1-3 5.5 3.114.52UT1-4 6.8 4.1153UT1.5-3 5.5 3.114.54UT1.5-47 4.115.55UT1.5-58.5 5.1176UT1.5-610 6.119.57UT2.5-3 5.8 3.119.58UT2.5-47 4.1169UT2.5-58.5 5.11810UT2.5-610 6.12011UT4-47.5 4.11812UT4-58.5 5.119.513UT4-610.5 6.121.514UT4-813.38.12415UT6-48 4.119.516UT6-59.2 5.121.317UT6-610.5 6.122.518UT6-813.58.42519UT10-612 6.22520UT10-814.28.227.2圆型绝缘端头编号总长A 0.75-151.81.2-1.5型号插入导线载面前后4.25 2.22-2.55 2.73-4 6.2 3.25-67国产叉型裸端头UT8-108.5 5.6型号螺栓口直径B L F H d2mm mm mm mm1RV1.25-3.2#4 3.2mm 5.717.8 4.952RV1.25-3.7S#63.7mm5.717.84.95345RV1.25-4S #8 4.3mm 6.620.1 6.36RV1.25-4L #8 4.3mm 821.577RV1.25-5#10 5.3mm 821.578RV1.25-6 1/4 6.5mm 11.627.511.19RV1.25-8 5/168.4mm 11.627.511.110RV1.25-10 3/810.5mm 13.631.613.911RV2-3.2#4 3.2mm 6.617.8 4.312RV2-3.7S#63.7mm6.617.84.3131415RV2-4S #8 4.3mm 6.621716RV2-4L #8 4.3mm 8.522.57.7517RV2-5S #10 5.3mm 8.522.57.751819RV2-6 1/4 6.5mm 1227.61120RV2-8 5/168.4mm 1227.61121RV2-103/810.5mm13.630.213.922RV5.5-3.7#6 3.7mm 7.221.4 5.923RV5.5-4S #8 4.3mm 7.221.4 5.92425RV5.5-5#10 5.3mm 9.525.58.326RV5.5-6 1/4 6.5mm 1231.51327RV5.5-8 5/168.4mm 1533.713.728RV5.5-10 3/810.5mm 1533.713.729RV5.5-121/213mm19.238.1161012.5美制螺栓号尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=19A型号编号导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=48A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=27A1030RV3.5-4#8 4.3mm824.57.731RV3.5-5S#10 5.3mm824.57.73233RV3.5-6 1/4 6.5mm1227.97.7螺栓口直径B L F Hd2mm mm mm mm1SV1.25-3.2#4 3.2mm 5.721.2 6.5234SV1.25-4S#8 4.3mm 6.421.2 6.55SV1.25-4M#8 4.3mm7.221.2 6.56SV1.25-4L#8 4.3mm8.121.2 6.57SV1.25-5S#10 5.3mm8.121.2 6.58SV1.25-5L#10 5.3mm9.521.2 6.59SV1.25-6S 1/4 6.5mm9.521.2 6.51011SV2-3.2#4 3.2mm 5.721.2 6.512SV2-3.7S#6 3.7mm 5.721.2 6.51314SV2-4S#8 4.3mm 6.421.2 6.515SV2-4M#8 4.3mm7.221.2 6.5 16SV2-4L#8 4.3mm8.121.2 6.5 17SV2-5S#10 5.3mm8.121.2 6.5 18SV2-5L#10 5.3mm9.521.2 6.5 19SV2-6S 1/4 6.5mm9.521.2 6.510 12.5 10叉型绝缘端头编号型号尺寸美制螺栓号导线截面：2。
常用接线端子规格整理
宽度F 内圆直径E长度D内径C1OT1-3 5.7 3.113.52OT1-47.4 4.115.53OT1-59 5.1174OT1.5-36 3.1145OT1.5-47.1 4.115.46OT1.5-59.2 5.1187OT1.5-610.5 6.1198OT1.5-813.28.1249OT1.5-1015.510.425.511OT2.5-37.2 3.114.212OT2.5-47.5 4.11613OT2.5-59.1 5.11814OT2.5-610.7 6.119.215OT2.5-813.38.12416OT2.5-1015.510.42618OT4-48 4.11919OT4-59 5.119.220OT4-611.1 6.32221OT4-813.38.225.522OT6-48.1 4.11923OT6-58.3 5.12124OT6-611 6.22325OT6-8148.325.726OT6-101810.432国产圆型裸端头OT总长A 1.92.12.73.24.35556.27.1插入导线截面0.75-1 1.2-1.5 2-2.5 3-4型号编号尺寸5-627OT10-613 6.325.528OT10-8158.329.229OT10-101710.332.130OT10-121912.535.831OT16-613.8 6.43032OT16-816.28.330.833OT16-1018.810.535.834OT16-1220.812.539.9宽度F 内圆直径E长度D 内径C 1UT1-3 5.5 3.114.52UT1-4 6.8 4.1153UT1.5-3 5.5 3.114.54UT1.5-47 4.115.55UT1.5-58.5 5.1176UT1.5-610 6.119.57UT2.5-3 5.8 3.119.58UT2.5-47 4.1169UT2.5-58.5 5.11810UT2.5-610 6.12011UT4-47.5 4.11812UT4-58.5 5.119.513UT4-610.5 6.121.514UT4-813.38.12415UT6-484.119.5国产叉型裸端头UT总长A 2.73.25.671.82.210.55556.28.50.75-11.2-1.52-2.5 3-4型号编号尺寸8-1014-16插入导线载面16UT6-59.2 5.121.317UT6-610.5 6.122.518UT6-8 5-613.58.47 4.22519UT10-612 6.22520UT10-814.28.227.2d D L1d21SC1.5-5 1.5 1.8 3.75 5.2162SC2.5-4 4.2183SC2.5-5 5.2204SC4-5 5.25SC4-6 6.56SC6-5 5.27SC6-6 6.58SC10-6 6.59SC10-88.410SC16-6 6.511SC16-88.412SC25-6 6.513SC25-88.414SC35-88.415SC35-1010.516SC50-88.417SC50-1010.530353844总长L 2024264.25.6SC系列铜接线端头1313.5168.577991179.844.85.56.57.5910.812.52.43.13.855.77.28.5253550插入导线载面2.5461016 5-6 8-10型号编号尺寸d2BLD mm mm mmmm1RV1.25-3.2#4 3.2mm 5.717.82RV1.25-3.7S #6 3.7mm 5.717.83RV1.25-4S #8 4.3mm 6.620.14RV1.25-4L #8 4.3mm 821.55RV1.25-5#10 5.3mm 821.56RV1.25-6 1/4 6.5mm 11.627.57RV1.25-85/168.4mm11.627.58RV1.25-10 3/810.5mm 13.631.611RV2-3.2#4 3.2mm 6.617.812RV2-3.7S #6 3.7mm 6.617.815RV2-4S #8 4.3mm 6.62116RV2-4L #8 4.3mm 8.522.517RV2-5S #10 5.3mm 8.522.519RV2-6 1/4 6.5mm 1227.620RV2-85/168.4mm1227.621RV2-10 3/810.5mm 13.630.222RV3.5-4#84.3mm824.5圆型预绝缘端头蓝颜色红4.34.9美制螺栓号型号编号导线截面：2.5-4mm2(美国线规14-12) 最大电流:lmax=37A 尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=19A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=27A23RV3.5-5S #10 5.3mm 824.524RV3.5-61/46.5mm1227.926RV5.5-3.7#6 3.7mm 7.221.427RV5.5-4S #8 4.3mm 7.221.428RV5.5-5#10 5.3mm 9.525.529RV5.5-6 1/4 6.5mm 1231.530RV5.5-8 5/168.4mm 1533.731RV5.5-10 3/810.5mm 1533.733RV5.5-121/213mm19.238.1d2BLD mm mm mmmm1SV1.25-3.2#4 3.2mm 5.721.24SV1.25-4S #8 4.3mm 6.421.25SV1.25-4M #8 4.3mm 7.221.26SV1.25-4L #8 4.3mm 8.121.27SV1.25-5S #10 5.3mm 8.121.28SV1.25-5L#105.3mm9.521.29SV1.25-6S 1/4 6.5mm 9.521.211SV2-3.2#4 3.2mm 5.721.212SV2-3.7S#63.7mm5.721.2黑黄颜色红叉型预绝缘端头美制螺栓号型号编号导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=48A尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=19A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=27A 6.26.74.314SV2-4S #8 4.3mm 6.421.215SV2-4M #8 4.3mm 7.221.216SV2-4L #8 4.3mm 8.121.217SV2-5S #10 5.3mm 8.121.218SV2-5L#105.3mm9.521.219SV2-6S 1/4 6.5mm 9.521.2 4.9蓝21SV3.5-4#8 4.3mm 824.822SV3.5-5#105.3mm824.823SV3.5-6 1/4 6.5mm 122824SV5.5-3.7#6 3.7mm 8.325.225SV5.5-4S #8 4.3mm 8.325.227SV5.5-5#10 5.3mm 923.928SV5.5-6S 1/4 6.5mm 923.930SV5.5-85/168.4mm1430ldL mm mmmm 1BV1.250.5-1.515 4.42619A 红2BV2 1.5-2.515 5.12627A 蓝3BV5.5 4-615 6.82648A 黄8PVN1.250.5-1.58 4.41619A 红9PVN2 1.5-2.58 5.11627A 蓝10PVN5.54-68.56.820.548A黄长短全绝缘中间接头黑黄蓝6.26.7颜色最大电流导线截面编号导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=48A 尺寸导线截面:0.5-6mm2 最大电流:lmax=48A型号导线截面：2.5-4mm2(美国线规14-12) 最大电流:lmax=37A 4.9FLHDmm mm mm mm1PTV1.25-9 1.9192PTV1.25-10 1.9203PTV1.25-121.9224PTV1.25-13 1.9235PTV2-9 1.9196PTV2-10 1.9207PTV2-121.9228PTV2-13 1.9239PTV5.5-132.825.512.56.7黄针型裸端头(TZ型）针型预绝缘端头（TZ-JTK型）颜色红蓝4.34.910型号导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=48A 尺寸尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=19A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=27A 编号10F L H D d mmmm mmmmmm1PTN1.25-9 1.913.82PTN1.25-10 1.914.83PTN1.25-12 1.916.84PTN1.25-13 1.917.85PTN2-9 1.913.86PTN2-10 1.914.87PTN2-121.916.88PTN2-13 1.917.89PTN3.5-10 2.814.810PTN3.5-13 2.819.811PTN5.5-132.819.865.63.4BdDLH mm mm mm mm mmmm1FDD1.25-1100.3 3.8 1.7 3.8194FDD1.25-1870.355.61.73.8196FDD1.25-2500.47.4 1.7 3.821母型预绝缘接头101.72.3354.84.86材料厚度尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=10A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=15A编号型号导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=19A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=27A导线截面：2.5-4mm2(美国线规14-12) 最大电流:lmax=48A 导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=27A编号型号 3.44.18FDD2-1100.3 3.8 2.3 4.31910FDD2-1870.355.62.34.31912FDD2-2500.47.4 2.3 4.32114FDD5.5-2500.47.43.45.72514BdDLHmm mm mm mm mm1MDD1.25-110 2.8 1.7 4.317.7103MDD1.25-1874.751.74.320105MDD1.25-250 6.35 1.7 4.321106MDD2-1874.752.34.320108MDD2-250 6.35 2.3 4.321109MDD5.5-2506.353.45.72513黄WLFC公型预绝缘接头片形预绝缘端头蓝10颜色红颜色导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=15A 导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=24A 尺寸编号型号导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=24A 尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=10A编号型号1DBV1.25-10 2.320102DBV1.25-11321113DBV1.25-14324144DBV1.25-18 2.328185DBV2-9 2.81996DBV2-18 2.328187DBV5.5-102.822.5106.7黄bDdHLmm mm mm mm mm1MPD1.25-1564 2.7 1.71021红2MPD2-15643.32.310213MPD2-1955 3.3 2.310214MPD5.5-1564 4.5 3.414255MPD5.5-19554.53.41425子弹型公预绝缘端头子弹型母预绝缘端头颜色蓝黄红蓝4.34.9导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=24A尺寸尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=10A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=15A编号型号b D d F L mm mm mm mm mm1FRD1.25-1564 2.7 1.77.323红2FRD2-15643.32.37.323.83FRD2-1955 3.3 2.37.323.84FRD5.5-1564 4.5 3.47.325.55FRD5.5-19554.53.47.325.5WBDdLmm mm mm mm mm1FDFN1.25-110 6.2 3.24 1.7202FDFN1.25-1877.8541.7203FDFN1.25-2509.3 6.64 1.722.54FDFN2-110 6.2 3.2 4.5 2.3205FDFN2-1877.854.52.3226FDFN2-2509.3 6.6 4.5 2.3247FDFN5.5-1877.85 5.7 3.423.88FDFN5.5-2509.36.65.73.425.5母全预绝缘接头黄颜色红蓝黄颜色蓝导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=10A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=15A 导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=24A 导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=10A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=15A 导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=24A 尺寸编号编号型号型号WFDCLmm mm mm mm mm1MDFN1.25-250 6.357.74 1.723红2MDFN2-250 6.357.7 4.5 2.324蓝3MDFN5.5-2506.357.76.33.425黄公全预绝缘接头颜色导线截面：4-6mm2(美国线规12-10) 最大电流:lmax=24A 尺寸导线截面：0.5-1.5mm2(美国线规22-16) 最大电流:lmax=10A导线截面：1.5-2.5mm2(美国线规16-14) 最大电流:lmax=15A 编号型号。
2017-7菲尼克斯-端子、配件选型手册
名称额定电压 V额定电流 A额定横截面 mm²长 mm 宽 mm 高 mm1信号、小电流UK2.580024 2.542.5 5.2422UT4100032447.7 6.2473UK5N 80032442.5 6.2474UK6N 80041642.58.2475UK16800761042.510.2546UT3510001253560.21665.77UK351000125355015.1628URTK/S 400416728.251.59RTO 4-T-TC 50041682.412.35110接地USLKG+红色 +RD 绿色 +GN 蓝色 +BU 黄色 +YE 橙色 +OG 棕色 +BN 黑色 +BK 白色 +WH 米白色 +BG 混.黑黄+FE终端固定件E/UK 50.59.535.3AP-ME METER 13866.58.2AP 3 CM 8966.510AP 2 CM 55.556.45分断大电流保护盖罩中、大电流颜色颜色表颜色表里的端子所有端子不一定有颜色表里端板隔板桥接件 螺桥接件 插标识条D-UK2.5ATP-UK FBRI 10-5N EBL 10-5ZB5 LGS1-9D-UT 2,5/10ATP-UK FBS 10-6ZB6 LGS1-10D-UK4/10ATP-UK FBI 10-6EB 10-6ZB6 LGS1-10D-UK4/10ATP-UK FBI 10-8EB 10-8ZB6 LGS1-10D-UK16ATP-UK FBI 10-10EB 10-10ZB10 LGS1-10TPNS-UK FBS 2-16ZB16 LGS1-10KT-S FBI 3-15D-URTK ATS-RTK FB 10-RTK/SSB 4-RTK/SEB 10-8ZB8 LGS1-10D-RT4-TTPNS-UKFBS 10-6ZB8 LGS1-10KLM-A终端固定架中间支撑架APH-ME APT-ME AP 3-TNS 35AP 3-TU AP 2-TU KS AP 2-TU附件：的端子颜色越不常用货期越长。
WAGO 750-402
目录
目录 • iii
1 重要说明 .................................................................................4 1.1 合法性........................................................................................4 1.1.1 版权声明............................................................................................4 1.1.2 人员资质 .......................................................................4 1.1.3 使用准备.......................................................................................4 1.2 警示图标..................................................................................................5 1.3 数字表示法......................................................................................5 1.4 安全提示.............................................................................................6 1.5 适用范围................................................................................................... 6
端子压着规格书
2-520183-2
2-521144-2
AWG22
20
18
2X22
2X20
1.65±0.05
1.65±0.05
1.78±0.05
1.78±0.05
1.78±0.05
4.5
7.3
9.08
4.5
7.3
7.2(单根)
7.9(双根)
红色
3-520140-2
AWG16
14
2X18
1.78±0.05
1.90±0.05
AWG28
26
24
22
0.60~0.65
0.65~0.70
0.70±0.05
0.75±0.05
1.0
2.0
3.0
4.0
2.5
加长5
VH
SVH-21T-1.1
SVH-21T-P1.1
AWG22
20
18
RV0.30
1.05±0.05
1.10±0.05
1.15±0.05
1.00±0.05
4.5
6.5
8.0
17
23
4.4/5.4
2-520128-2
AWG22
20
18
2X22
2X20
1.65±0.05
1.65±0.05
1.78±0.05
1.78±0.05
1.78±0.05
4.5
7.3
9.08
4.5
7.3
8.0(单根)
8.5(双根)
红色
3-520132-2
AWG16
14
2X18
1.78±0.05
1.90±0.05
WAGO(万可)接线端子型号大全
3 17*20.5*14.5
500
5 26.6*20.5*14.5
400 50 50 50
224-101
8.5*20.5*15.5
1000
224系列
224-104 224-201
8.5*20.5*15.5 8.5*20.5*15.5
100 50
224-112
15.5*42*8.5
1000
773系列
224-114 773-102 773-104 773-106 773-108 773-173 773-602 773-604
运行温度105℃
运行温度120℃
固定支架
适于单排(14mm)和双排(18.5mm) 连接器
100 50 1000 1000 1000 1000 500 50
WAGO（万可）接线端子型号大全
适用导线 单股导线、多股导线、细多股导线及镀锡处 理的细多股导线、经过端部紧固处理的细多 股导线 单股导线、多股导线、细多股导线及镀锡处 理的细多股导线、经过端部紧固处理的细多 股导线 单股导线、多股导线、细多股导线及镀锡处 理的细多股导线、经过端部紧固处理的细多 股导线 单股导线、多股导线、细多股导线、经过端 部紧固处理的细多股导线、加入冷压接头的 细多股导线、加有接线针的细多股导线 单股导线、多股导线、细多股导线、经过端 部紧固处理的细多股导线、加入冷压接头的 细多股导线、加有接线针的细多股导线 单股导线、多股导线、细多股导线、经过端 部紧固处理的细多股导线、加入冷压接头的 细多股导线、加有接线针的细多股导线 外观
2 4 6 8 3 2 4
15.5*42*8.5 9.2*19.5*13.1 13*19.5*13.1 18.8*19.5*13.1 24*19.5*13.1 25.6*20.1*14.2 9.2*19.5*13.1 13*19.5*13.1
Wago 开关和光纤隔离器产品概述说明书
Product Overview Relays and Optocouplers23 Relays and Optocouplers4 –5 Features, Benefits, Applications859 Series 6 – 9Rail-Mounted Terminal Blockswith Miniature Switching Relay and Optocoupler857 Series 10 – 13 Sockets with Miniature Switching Relay788 Series 14 – 17 Sockets with Miniature Switching Relay858 Series 18 – 21 Sockets with Industrial Relay286 Series 22 – 27 Pluggable Modules – Relays287 and 288 Series 28 – 31 Mounting Carriers with Miniature Switching Relay789 Series 32 – 34 Relay Modules in DIN-Rail Mountable EnclosureFor complete specifications visit us online at → Service → Documentation → Interface Modulesor look for the quick link Technical documentationOptocouplers4•Easy to install, easy to maintain •Economical to purchase, efficient to install Modern equipment design requires multiple WAGO relay modules –The convenient interface between electronics and peripheryIn modern automation systems, electrome-chanical relays safely connect process peripherals with electronic control, alarm and monitoring systems. For example, relays perform the following tasks:• Electrical isolation with high isolation levels between input and output circuits • Adjustment of differing signal levels• Signal amplification and/or signal multiplication if varying potentials existTo perform these tasks and more, WAGO AUTOMATION offers a full range of relay modules ready to support a diverse array of applications. Depending on the task and application requirements, there is a choice of relay modules with different rated voltages, contacts, contact materials, housings and designs. In addition to standard switching relays, bistable relays, timing relays, latching re-lays and safety relays with force-guided contacts are also available.The comprehensive design of modern relays provides applications with the following benefits:• Immunity to electromagnetic interference and transient voltages• High, short-term overload capacity on both input and output sides • Minimal switching loss• A single module that switches both direct and alternating currents5As a link between process peripherals and electronic control, alarm and monitoring systems, optocoupler modules boast the following advantages over electromechanicalrelays:• Longer service life – no mechanical wear• High switching frequency due to short switch-on and switch-off times • Vibration resistance • No contact bouncing • “Noiseless” switching• Low control power requirementthe above benefits to the following tasks:• Electrical isolation between input and output circuits • Adjustment of differing signal levels • Signal amplificationOptocouplers are available with different rated voltages, switching capacities and housing options to suit any application.Relays and optocouplers are used everywhere where electrical signals must be transmitted and galvanic isolation, signal adjustment or amplification are required. They are suitable for all industrial applications: process and power technology, rail vehicles, shipbuilding, as well as control cabinet applications.Benefits of WAGO relays and optocouplers: • Easy termination of conductors from 0.08 mm² to 2.5 mm² (28-14 AWG)• Optimized for any application • Wide range of accessories(e.g., adjacent jumpers, marking material)• Switchable loads from 1 m A to 16 AWAGO optocouplers – The modern and powerful alternative6Vibration-proof – fast – maintenance-free CAGE CLAMP ® termination for all conductor types.fine-strandedferruledsolidRail-Mounted Terminal Blocks with Miniature Switching Relay and Optocoupler – 859 Series859 Series Features/Benefits:•6 mm-wide housing for DIN 35-rail mounting•Front-side jumpers streamline connections•LED for status signal indication•Each termination point offers an integratedtest location7* In order to prevent the gold layer from being damaged, these values shall not be exceeded.Higher switching power leads to evaporation of the gold layer. The resulting deposits in the housing may cause sparkovers between the coil and the contact.8Rail-Mounted Terminal Blocks with Miniature Switching Relay, 859 SeriesRail-Mounted Terminal Blocks with Optocoupler,859 Series9857 SeriesFeatures/Benefits:• Pluggable relays andoptocouplers10JUMPFLEXOptocoupler – 857 SeriesA11Sockets with Miniature Switching Relay,857 Series8-Channel Interface Adapter for System Wiring* In order to prevent the gold layer from being damaged, these values shall not be exceeded. (In case of damaged gold layer, the values in parenthesis apply).Higher switching power leads to evaporation of the gold layer.The resulting deposits in the housing may cause sparkovers between the coil and the contact.** For use on the 857 Series socket’s coil side *** For use on the 857 Series socket’s contact side12Sockets with Solid State Relay,857 Series Array13788 Series Features/Benefits:• Relays with 1 or 2 changeover contacts – up to 16 A and 250 V of switching power • DIN-rail mount modules • WMB or continuous strip• Pluggable switching status indicator (LED) with integrated recovery diodeVibration-proof – fast – maintenance-free CAGE CLAMP ®S termination for all conductor types.fine-stranded*ferruled*solid14Sockets with Switching Relay and Optocoupler –788 Series15Sockets with Miniature Switching Relay, 788 Series Array* In order to prevent the gold layer from being damaged, these values shall not be exceeded.Higher switching power leads to evaporation of the gold layer.The resulting deposits in the housing may cause sparkovers between the coil and the contact.16Sockets with Miniature Switching Relay,788 SeriesSockets with Optocoupler, 788 Series17858 Series Features/Benefits:• Relays with 5 A power contacts or 50 mA gold contacts for dry switching circuits • Integrated LED indicator, mechanical relay status and manual operation• Dual conductor entries with CAGE CLAMP ®S COMPACT for all connections • Compatible with industrial relays utilizing standard pin spacing• Optional 858-402 push-in jumpers common Vibration-proof – fast – maintenance-freeCAGE CLAMP ®S termination for all conductor types.fine-stranded*ferruled*solid18*Push-in wiring technologytwo conductor entries at each CAGESockets with Industrial Relay –858 Series19Sockets with Industrial Relay,858 Series Array* In order to prevent the gold layer from being damaged, these values shall not be exceeded.Higher switching power leads to evaporation of the gold layer.The resulting deposits in the housing may cause sparkovers between the coil and the contact.202122286 Series Features/Benefits:• Easy termination of conductors from 0.08 mm² to 2.5 mm² (28 -12 AWG)• Space-saving combination of electrical and electronic functions on a rail-mounted terminal block• Module removal provides fast and safeseparation between logic and control powerVibration-proof – fast – maintenance-free CAGE CLAMP ® termination for all conductor types.fine-strandedferruledsolidPluggable Relay and Optocoupler Modules for Carrier Terminal Blocks – 286 Series23Pluggable Modules – Relays,286 Series Array24Pluggable Modules – Relays, 286 SeriesPluggable Modules – Optocouplers, 286 Series28Vibration-proof – fast – maintenance-free CAGE CLAMP ® termination for all conductor types.fine-strandedferruledsolidMounting Carriers with Miniature Switching Relay – 287, 288 Series29Mounting Carriers with Miniature Switching Relay, 287, 288 Series303132Vibration-proof – fast – maintenance-free CAGE CLAMP ® termination for all conductor types.fine-strandedferruledsolidRelay Modules in DIN-Rail MountableEnclosure – 789 Series789 Series Features/Benefits:• Available with up to 2 break contacts and2 make contacts, or 4 make contacts in a33Relay Modules in DIN-Rail Mountable Enclosure, 789 Series343551243349 0888-0832/0000-0214 P r i n t e d i n t h e U n i t e d S t a t esWAGO CorporationN120 W19129 Freistadt Road Germantown, Wisconsin 53022800 / DIN Rail (346-7245)Fax 262 / 255-3232****************MexicoWAGO Corporation QueretaroTel. 001/800/309/5975 + 52/442/221/5946Fax + 52/442/221/5063 CanadaWAGO CorporationTel. 800/DIN Rail (346-7245)Fax 262/255-3232。
常用插拔式接线端子适配线号与线径范围
187锁扣母端子 系列
LS2050801-30C LT2050501-30C LT2050801-30C
205旗型母端子 系列
FT2050501-30C FT2050801-30C TT2050501-50C
205-0.5旗型 205-0.8旗型 205-0.5公端子插片 205-0.8公端子插片
20-16 22-20 20-16
0.5189-1.3180 0.3247-0.5189 0.5189-1.3180
国内通常叫做2.8 .品名栏中未注明高脚短脚的视为常规标准压线脚. 作者红云五金端子QQ1329299144给于指正和建议.
适配线径范围(AWG#)
24-20
适配线号范围(mm²)
0.2047-0.5189
国内通常叫做4.8 .品名栏中未注明高脚短脚的视为常规标准压线脚. 作者红云五金端子QQ1329299144给于指正和建议.
适配线径范围(AWG#)
24-20
适配线号范围(mm²)
0.2047-0.5189
20-16
0.5189-1.3180
24-22
0.2047-0.3247
20-16
0.5189-1.3180
187锁扣母端子 系列
LS1870801-30C LT1870501-30C LT1870801-30C FT1870501-30C FT1870801-30C
187旗型母端子 系列
FD1870501-30C FD1870801-30C FLS1870501-30C FLS1870801-30C
187公母端子
14-10
2.075-5.2600
24-20
0.2047-0.5189
接线端子 冷压端头 接线端子标准 接线端子规格 (30)
电缆接头
日成公制电缆接头 AG 日成德制电缆接头 PG 日成美制电缆接头 NPT 日成英制电缆接头 G 日成公制电缆防水接头 ST-M 日成公制电缆接头 MGA 日成德制电缆接头 PGA 日成公制电缆接头 MGB 日型电缆防水接头PGB NPT
尼龙扎带
日成自锁式尼龙扎线带 G 日成超宽型尼龙扎线带 GEHD 日成抗紫外线扎带 GUV 日成耐候性超宽尼龙线带 GUV 日成耐寒型尼龙扎带 GCS 日成耐热型尼龙扎线带 GHS 日成防火级尼龙扎线带 GV0 日成彩色尼龙扎线带 日成标牌尼龙扎线带 MCV
日成收缩绝缘端子 RF-H S 日成收缩绝缘端子 RF-HS
日成圆形尼龙绝缘端子 RFN 日成圆形尼龙绝缘端子 RFN
日成叉形尼龙绝缘端子 YFN 日成叉形尼龙绝缘端子 YFN
日成尼龙中间端子 B N 日成尼龙中间端子 BN
日成尼龙旗形端子 FN 日成尼龙旗形端子 FN
/content_products_203.html
日成O T 圆形开口接线端子 日成OT圆形开口接线端子
日成铜管端子 H UPD 日成铜管端子 HUPD
日成铜管端子 H UPD90 特点:90度端头
日成铜管端子 H UPD45 日成铜管端子 HUPD45
日成3 M 电工胶带 日成3M电工胶带
日成3 M 自粘橡胶防水胶带 日成3M自粘橡胶防水胶带
日成高压黄腊带 日成高压黄腊带
日成铜管端子 DI N 日成铜管端子 DIN
日成圆形裸端子 DI N 日成圆形裸端子 DIN
日成铜管端子 DTS 日成铜管端子 DTS
日成铜管端子 C 45 日成铜管端子 C45
日成铜管端子 TPE 日成铜管端子 TPE
日成扁形铜管端子 C P 日成扁形铜管端子 CP
EHU组合液压系统使用说明书
警告 z 如在油箱无油时运转，会使油泵部分损坏烧毁。 z 在机器的初始运转时，由于需向机器侧的液压回路供油，应注意油箱内油位在减少。 z 由于机器侧的液压回路作用，使油箱内的油面变动很大，应注意油箱内的油有时会溢出，有时
(1) 应通过端子盒的配线口配置电线。
配线口应采用符合 IP54 以上要求的配线电线管，电缆
夹紧件等。
[ 推荐电缆夹紧件：RAPPU 公司产品 ST16]
[ 螺钉尺寸
：PG16]
※电源线应使用 245IEC/H05RR-F 的电线。
(2)接地线应接在端子板的地线连接处。
(3)电源线应接在电源端子板 （L1、 L2、 L3）上 （无极 性）。
会不足。
11
电气配线 应按照端子盒盖里面的配线图 （下图），正确而可靠地连接电气配线。
危险 z 为了防止电路过电流如短路等和防止控制部件过载，请在主电源电路配备根据欧共体EN60204-
1 规定的无熔丝热继电器或漏电断路器等安全装置。 （各机型的电流容量，请参照下表。） z 为了泄放变频回路泄漏的电流，接地端子必须使用第三接地等级以上的接地方式。 （必须不通过断路器等保护装置，直接接地） z 必须在主机安装好以后再进行配线作业。 z 进行配线作业之前，必须切断总电源侧的断路器，并确认电源已切断。 z 电源线绝对不能与报警端子和控制信号端子连接。 z 不能使用超过液压装置规定电压的电源。
重量表 （但是，不包含工质油）
危险 z 如不安装防振橡胶保护衬垫，起吊时会使防振橡胶磨损、滑脱，设备会有掉下、翻倒的危险。 z 勾住吊环螺栓以外 （泵配管）等，的构件起吊时有掉下、翻倒的危险。 z 应确认液压设备的重量，在起重吊具额定承重内吊装。
wago普通轨装式接线端子
50 (2x25)
梳状间隔跨接器, 适于插入端子的进线孔中
绝缘,
IN = 接线端子IN
2插脚
279-492 200 (8x25)
操作工具, 绝缘
2插脚
279-432
1
3插脚
279-433
1
操作工具, 绝缘
10插脚
279-440
1
3
普通/保护接地/屏蔽接地及4防爆接线端子 2.5 mm² 280 系列
100 (4x25)
导线型跨接器,
5
绝缘,
IN 9 A,
导线截面积 0.75 mm²
60 mm
249-125
110 mm
249-126
250 mm
249-127
190页 190页 107页
100 (4x25) 100 (4x25) 100 (4x25) 100 (4x25) 100 (4x25) 100 (4x25)
AWG 28 - 12 * 600 V, 20 AU 600 V, 15 A2
端子厚度 5 mm / 0.197 in L 8 - 9 mm / 0.33 in 2
30.08 - 2.5 mm²
800 V/8 kV/3 1 IN 20 A
AWG 28 - 12 * 600 V, 20 AU 600 V, 15 A2
<_
<_
<_
( 32 mm/1.26 in ) <____ 52 mm/2.05 in ____>
( 32 mm/1.26 in ) <_____ 62.5 mm/2.46 in ______>
< 42.5 mm/1.67 in > <________ 73 mm/2.87 in __________>
本安电源、接线端子、穿墙端子、喇叭口、密封圈选型
A5
M56x3
19.1~29.6
B1~B5 喇叭口
型号 配合尺寸 B1 B2 B3 B4 B5 Φ46 Φ65 Φ82 Φ100 Φ125
导线直径 （mm） 19.1~29.6 29.6~40.0 41.1~51.0 52.4~62.7 64.6~77.7
备注
其他附件如下
联通节 A0~A5、B1~B5
JF6/1140 1140V Φ12
图纸
爆 证 防
JF8/660 660V Φ16
104
图纸
爆 证 防
JF8/1140 1140V Φ16
120
图纸
爆 证 防
JF10/660 660V Φ18
116
图纸
爆 证 防
JF10/1140 1140V Φ18
132
图纸
爆 证 防
JF12/660 660V Φ22
B5 密封圈、堵头等附件 型号 A0 A1 A2 A3 A4 A5 B1 B2 B3
Φ128 密封圈外 径（mm） Φ１８ Φ２２ Φ２７ Φ３３ Φ３９ Φ５０ Φ５２ Φ６８ Φ８５
B4 Φ１０３ B5 Φ１２８
75 导线直径 可选割圈（mm） (mm) 6.0~9.0 Φ8、Φ9 9.3~12.5 Φ10、Φ13 10.6~13.1 Φ12、Φ15 Φ12、Φ15、 10.6~17.9 Φ19 Φ15、Φ19、 13.1~23.0 Φ23 Φ22、Φ26、 19.1~29.6 Φ30 Φ22、Φ26、 19.1~29.6 Φ30 Φ32、Φ36、 29.6~40.0 Φ40 Φ42、Φ46、 41.1~51.0 Φ51, , Φ56、Φ60、 52.4~62.7 Φ63 64.6~77.7 Φ68、Φ73、 Φ78