船舶常用英语(一)
船舶常用英语(一)讲解
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶常用英语(一)
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶常用英语(一)汇总
船舶常用英语(一)汇总一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipcargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-containership 全集装箱船semi-containership 半集装箱船multi-purposecontainer ship 多用途集装箱船general cargo ship/vessel/carrier杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber)carrier运木船cattle carrier 运牲畜船multi-purpose ship多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay舷墙扶强材bunker tank 燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱第 11 页共 45 页cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁第 12 页共 45 页companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫第 13 页共 45 页dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱第 14 页共 45 页forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）第 15 页共 45 页handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱第 16 页共 45 页hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate第 17 页共 45 页龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽第 18 页共 45 页molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam防挠振梁panting stringer 防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板第 19 页共 45 页plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam 梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档第 20 页共 45 页scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus 剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate上（下）支架板upper (lower) stool 上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)电弧mutator整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干第 41 页共 45 页A. Remove, crop etc.1.Removed拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮第 42 页共 45 页2.fitted & ground拂磨3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true第 43 页共 45 页校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊第 44 页共 45 页8 tackweld 点焊、平头焊、定位焊第 45 页共 45 页。
船舶英语词汇
船舶专用词汇1.船舶的分类passenger ship 客船general cargo ship 杂货船bulk cargo carrier 散货船container ship 集装箱船roll on/roll off ship 滚装船tanker 油船liquid gas carrier 液化气船barge 驳船barge carrier 载驳船dredger 挖泥船floating crane 起重船floating dock 浮船坞ice breaker 破冰船drilling platform 钻井平台drilling ship 钻井船trawler 拖网渔船stern ramp trawler 尾滑道拖网渔船tug boat 拖船fire boat 消防船ocean survey ship 海洋调查船cruiser 巡洋舰destroyer 驱逐舰frigate 护卫舰aircraft carrier 航空母舰submarine 潜艇hydrofoil craft 水翼艇air cushion vehicle 气垫船—hovercraft 全浮式气垫船—sidewall air cushion vehicle 侧壁式气垫船small waterplane area twin hull ship 小水线面双体船semi-submerged catamaran 又称为半潜双体船2.船体结构longitudinal bending 总纵弯曲hogging 中拱弯曲sagging 中垂弯曲longitudinal strength 总纵强度transverse strength 横向强度local strength 局部强度hull 船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 艏楼bridge 桥楼poop 艉楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁fore peak bulkhead 艏尖舱舱壁after peak bulkhead 艉尖舱舱壁3.外板和甲板板shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 船底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板upper deck 上甲板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板4.船底结构center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 钢板折边法兰bilge bracket 舭肘板floor 肋板solid floor 主肋板watertight floor 水密肋板bracket floor 框架肋板lightened floor 轻型肋板stiffener 加强筋扶强材bulb plate 球扁钢angle bar 不等边角钢bottom center girder 中底桁bottom center girder 旁底桁duct keel 箱形中底桁pipe tunnel 管隧reverse frame 内底横骨bottom frame 船底肋骨longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨inner bottom plate 内底板margin plate 内底边板man hole 人孔bilge well 污水井bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 艉室emergency exit 应急通道bilge keel 舭龙骨5.舷侧结构Integrated barge 分节驳frame 肋骨main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材6.甲板结构beam 横梁deck beam 普通横梁hatch end beam 舱口端横梁deck girder 甲板纵桁side stringer 舷侧纵桁hatch side girder 舱口纵桁beam knee 梁肘板sponson deck 舷伸甲板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 货舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁pillar 支柱topside tank 顶边舱excess hatch 出入舱口expansion trunk 膨胀井7.舱壁结构bulkhead 舱壁cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical stiffener 垂直扶强材8.首尾端结构vertical bow 直立型艏raked bow 前倾型艏clipper bow 飞剪型艏ice breaker bow 破冰型艏elliptical stern 椭圆形艉cruiser stern 巡洋舰型艉transom stern 方形艉fore peak艏尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱breast hook 艏肘板stem 艏柱steel plate stem 钢板艏柱forged steel stem 锻钢艏柱combination cast and rolled stem 混合式艏柱tunnel 管隧thruster 侧推器after peak 艉尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame 艉柱shoe piece 艉柱底骨rudder post 舵柱propeller post 螺旋桨柱propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架9.上层建筑和机舱棚结构accommodation 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass platform 罗经平台expansion joint 伸缩接头derrick post桅杆derrick platform 起货机平台tower post 塔式桅stern door 艉门bow door 艏门visor type 罩壳式side hinged type 边铰链式pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱ballast water tank 压载水舱conning tower sail 指挥台围壳渔业船舶种类2.1 渔船fishing vessel 用于商业性捕捉鱼类、鲸、海豹、海象或其他生物资源的船舶之统称。
船舶常用英语(1)
Aamidships 在船中部；在纵中线上accommodation 居住舱室accommodation deck 起居舱室；旅客甲板alvage ship 救捞船athwartships 横对船体（与船首尾线直交）airscrew ship; aerial propeller vessel 空气螺旋桨船accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管auxiliary machinery 辅助机械；辅机alignment 对准，校直angle steel 角钢aluminum alloy 铝合金annealing 退火allowance 余量assembly 装配asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料alloy steel 合金钢angle cutter 角钢切断机acetylene generator 乙炔发生器arc welding 电弧焊angle of vanishing stability 稳性消失角adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏arcking (arcing) 电弧aerated（橡胶、电缆）腐烂、腐坏aged 老化accommodation deck 起居舱室；旅客甲板A.C. 尾楼，空调，交流机A.C. MACH Room 空调机房accommodation ladder manrope 舷梯扶索accommodation ladder platform 舷梯平台accommodation ladder 舷梯accommodation 居住舱室acetylene generator 乙炔发生器adjusted 调整，校正adjusted for alignment 校正拉线adjusted for centering 校中adjusted for clearance 校正间隙adjusted for deflection 校偏adjusted true 校正拉线aerated （橡胶、电缆）腐烂、腐坏aft draft 尾吃水after body 后（部船）体after peak 艉尖舱after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱aged 老化air hole 透气孔air hole 空气孔air pipe 空气管aircraft carrier 航空母舰airscrew ship; aerial propeller vessel 空气螺旋桨船alignment 对准，校直allowance 余量alloy steel 合金钢aluminum alloy 铝合金amidships 在船中部；在纵中线上angle cutter 角钢切断机angle of vanishing stability 稳性消失角angle steel 角钢annealing 退火annex 附加anxiliary machinery 辅机appendage （水线下）附件appendage （船体水线下的）附体；附件arc welding 电弧焊arcking (arcing) 电弧assembly 装配athwartships 横对船体（与船首尾线直交）autometic welding 自动焊auxiliary machinery 辅助机械；辅机Bbalanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀boat, craft 艇barge; lighter 驳船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船bevel 斜角；斜面base line 基线barge carrier; lighter aboard ship(LASH)载驳船be veed out 刨除brass 黄铜bend test 弯曲试验brittleness 脆性buckling 皱折butt joint welding 对接焊building block, stocks 枕木building berth 船台building dock 干坞bulk (cargo) carrier 散货船buoyancy 浮性buoyancy curve 浮力曲线broken off 破掉（破裂后跌落）broken 破裂，破碎bent 弯曲buckled 皱折bulged 鼓起，凸出burst 爆破（指高压管路）blown off (packing) 吹脱blocked 阻塞built up by welds 堆焊butt welded 对接焊belted 熔化burnt 烧坏blackened 发黑brush set incorrectly 碳刷安装不正确broken down 击穿bored round 镗圆blanked 封没bearing metal 轴承合金batteries 电池组B.P(bulb type) 球扁钢balanced rudder 平衡舵ballast 压载ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）ballast 压载（物）Bar 工字钢barge 驳船barge carrier; lighter aboard ship(LASH) 载驳船barge; lighter 驳船base line 基线batten 板条，压条batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板batteriesBCK 肘板be veed out 刨除beam 横梁beam bracket 梁肘板beam camber 梁拱beam 横梁bearding 交合线，榫（艏柱或艉柱上）bearing metal 轴承合金beelson 内龙骨belted 熔化bend test 弯曲试验bending moment 弯矩bent 弯曲bevel 斜角bevel 斜角；斜面bevelled 坡口，有斜面的，圆锥体的，斜的，斜切的，斜面的bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bilge well 污水井bilge 舭部；舱底；（船底）污水沟bitt 系缆桩blackened 发黑blanked 封没blocked 阻塞blown off (packing) 吹脱boat, craft 艇boatswain 水手长bollard 系缆桩；系船柱；双系柱bollard(bitt) 系缆桩bolster 枕垫bonnet 烟囱帽；机罩boom 吊臂boom crutch(support; rest) 吊杆支架boom 杆；吊杆；桁；叉架bored round 镗圆bossing 轴包套bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow fender 艏护垫bow flare 艏外飘bow flare 艏部外飘bow thruster 首侧推器bow 船首，船头bracket 肘板；（三角）拖架brass 黄铜breakwater 防浪板breakwater 挡浪板bridge deck 桥楼甲板bridge 桥；桥楼；驾驶台brittleness 脆性broken 破裂，破碎broken down 击穿broken off 破掉（破裂后跌落）brom 杆brush set incorrectly 碳刷安装不正确buckled 皱折buckling 皱折building berth 船台building block, stocks 枕木building dock 干坞built up by welds 堆焊built up by welds 堆焊built-up section 组合型材bulb angle 圆头角材bulb stern 球形船尾bulbous bow 球形船首，球鼻首bulged 鼓起，凸出bulk (cargo) carrier 散货船bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulkhead 舱壁bull’s eye舷窗bulwark plating 舷墙板bulwark stay 舷墙扶强材bulwark 舷墙bunker tank 燃料舱buoyancy 浮性buoyancy curve 浮力曲线burnt 烧坏burst 爆破（指高压管路）bushing 衬套butt joint welding 对接焊butt joint(seam) 平接缝butt riveting 对接铆butt welded 对接焊butt welding 对接焊butt 端接；残片butterfly clip 蝴蝶夹bypass valve 旁通阀Ccable stopper止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切combined framed ship 混合骨架式船coaster 沿海船channel ship 海峡船civil ship; merchant ship 民用船；商船coasting passenger and cargo ship沿海客货船cargo ship; freighter 货船cargo liner 定期货船container ship 集装箱船coal carrier; coaler 运煤船cattle carrier 运牲畜船chemical tank 化学品液货船container barge 集装箱驳船cutter suction dredger 绞吸挖泥船cable layer; cable ship 布缆船cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀copper 紫铜casting 铸件，铸造center line 中心线，中线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线cropping 割掉construction plan 结构图co2 gas welding 二氧化碳气体焊cutting torch 割炬channel bar 槽钢cut of order (in trouble) 故障could not be started(failed to start) 不能启动chapped 龟裂，折裂canted 倾斜curled 卷曲（指绳索）collapsed 倾陷，倾倒corrosion 腐蚀chafed 擦痕cracked 裂痕clogged堵塞（常指管子的堵塞）choked 卡住，阻塞chopped off 崩缺cracked 开裂commutator 整流器coked 结焦charred 结碳completely discharged（电）完全发光cropped & renewed 割换（管、板、栏杆）cut off 割除closed up by welds （面积、深度、高度较大）焊补cleaned 清洁chipped & scraped 拷锈（油漆）checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙C.PL 补板cable layer; cable ship 布缆船cable stopper 止链器cable stopper 止链器camber 翘角，弯度，曲面，弧线，中高度，外胎定型camber of beam 梁拱camber of beam 梁拱camber 翘曲cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨canted 倾斜cantilever 悬臂梁cantilever 悬臂梁capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩capstan 绞缆桩capstan 起锚机capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo liner定期货船cargo port 装货舷梯，舷门cargo ship; freighter 货船casting 铸件，铸造cat walk （油轮上的）天桥，步桥cattle carrier 运牲畜船center girder 中底桁center line 中心线，中线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center strake 中央内底板chafed 擦痕chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 导链管chain pipe 锚链管chain stopper 止链器channel bar 槽钢channel ship 海峡船chapped 龟裂，折裂charred 结碳checked 检查checked for alignment 检查拉线checked for centering 检查中心位置checked for clearance 检查间隙checked for insulation resistance 检查绝缘电阻checked for roundness 检查圆度chipped & scraped 拷锈（油漆）CHL(channel bar) 槽钢chock 木楔，导缆钩，轧辊轴承，塞子，垫木，定盘，垫块，轴承座，制动垫块chock 导缆器；垫木choked 卡住，阻塞chopped off 崩缺civil ship; merchant ship 民用船；商船cladding 镀层，表面处理clamp plate 夹板，压板cleaned 清洁cleat 系绳铁角（羊角），系缆墩，cleat 羊角；系绳铁栓；防滑条clogged 堵塞（常指管子的堵塞）closed up by welds （面积、深度、高度较大）焊补co2 gas welding 二氧化碳气体焊coal carrier; coaler 运煤船coaming 舱口围板coaming 围板；舱口围板coaster 沿海船coasting passenger and cargo ship 沿海客货船coating 涂层，敷料cofferdam 隔离舱coked 结焦collapsed 倾陷，倾倒collar 补板collar plate 封板collision bulkhead 船首舱壁；防撞舱壁column 风管combined framed ship 混合骨架式船commutator 整流器companion way(hatch) 升降口compass 罗盘completely discharged （电）完全发光construction plan 结构图container ship 集装箱船copper 紫铜corrosion 腐蚀corrosion 腐蚀，侵蚀corrugated bulkhead 槽形板，压槽板corrugated bulkhead槽形舱壁corrugation 皱；槽形；波形could not be started(failed to start) 不能启动cracked 裂痕cracked 开裂cropped & renewed 割换（管、板、栏杆）cropped and renewed 割换cropping 割掉cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser 巡洋舰cruiser stern 巡洋舰型船尾crutch(rest) 支架curled 卷曲（指绳索）curtain plate 幕板curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线cut of order (in trouble) 故障cut off 割除cut out 开口；切cutout 开口，切口cutting torch 割炬Ddavit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷draft figures 吃水尺度deck ship 甲板船double shell ship 双壳船dredger 挖泥船designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水diesel ship 柴油机船double shell barge 双壳驳dipper dredger 铲斗挖泥船ductility 延展性，可塑（锻）性damage plan 损坏示意图docking plan 进坞图deflection, deflexion 挠曲deformation 变形descale 除锈detachment 脱开，脱焊dynamical stability（curve）动稳性（曲线）distorted 扭曲，歪扭dangerous accumulation of inflammable vapors 可燃气体危险集积deficient 不足，缺少dropped 跌落defective 有缺陷的（失效）damaged 损坏damaged beyond repair 损坏了无法修复disconnected 断开（线、管接头）distorted （轴线弯曲并扭转）扭曲detached 脱壳deflected 偏斜dry water 水干dismantle 拆卸（某一零件）disassembled 拆散（解体）deteriorated 蚀薄decayed （电缆）腐烂、腐坏drawn out 抽出damage plan 损坏示意图damaged 损坏damaged beyond repair 损坏了无法修复dangerous accumulation of inflammable vapors可燃气体危险集积davit 吊柱，吊艇柱davit 吊艇架；吊艇柱decayed （电缆）腐烂、腐坏deck 甲板deck beam 甲板横梁deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deckhouse 甲板室deep tank 深舱defective 有缺陷的（失效）deficient 不足，缺少deflected 偏斜deflection, deflexion 挠曲deformation 变形derrick 吊杆descale 除锈designed waterline breadth设计水线宽designed waterline length设计水线长destroyer 驱逐舰detached 脱壳detachment 脱开，脱焊Detail 零件,零件图,大样,细节,详图,明细,详细,（vt.详述,画细部图,）deteriorated 蚀薄DIAPH(diaphragm) 隔板diaphragm 隔板，横板，挡泥板diaphragm 隔板diesel ship 柴油机船disassembled 拆散（解体）disconnected 断开（线、管接头）dismantle 拆卸（某一零件）distorted （轴线弯曲并扭转）扭曲distorted 扭曲，歪扭docking plan 进坞图double bottom 双层底doubling plate 双层焊合板draft 吃水draft 吃水draft figures 吃水尺度drain hole 流水孔drain hole 排水孔drain plate 拦水扁铁drawn out 抽出dredger 挖泥船dropped 跌落dry water 水干duct keel 箱形龙骨ductility 延展性，可塑（锻）性dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷dynamical stability（curve）动稳性（曲线）Eend bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板electrically-propelled ship 电力推进船deck barge 甲板驳equal angle steel 等边角钢even keel （首尾）等吃水，平载extreme breadth 最大宽度excess clearance 间隙过大excess backlash 齿隙过大excess vibration 振动过大excess noise level 噪音过大entrance angle 进水角end elevation 后面图evolute 展开线end launching 纵向下水elastic limit 弹性极限elasticity 弹性empty 空的eroded 侵蚀engine break-down 因故障机器突然停车escaping of cool 逃冷elastic limit 弹性极限elasticity 弹性electrically-propelled ship电力推进船emerg gererator set 应急发电机设备empty 空的end bracket 端肘板end elevation 后面图end launching 纵向下水engine bed 机座engine break-down 因故障机器突然停车engine casing 机舱围壁entrance angle 进水角equal angle steel 等边角钢eroded 侵蚀ESC 逃生口escape scuttle （船内）应急出口escape trunk （船内）应急通道escape vent 逃生口escape vent 脱险口escaping of cool 逃冷even keel （首尾）等吃水，平载evolute 展开线excess backlash 齿隙过大excess clearance 间隙过大excess noise level 噪音过大excess vibration 振动过大expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板extreme breadth 最大宽度Fface plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔flush deck ship 平甲板船full-container ship 全集装箱船flat plate 钢板floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞former/aft draft 首/尾吃水freeboard 干舷fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线floatable length 可浸长度fter body 后（部船）体ferry 渡船freight ferry 货物渡船fishing vessel(boat) 渔轮flexibility 挠性，柔性，易弯性friability 易碎性forging 锻件，锻造fiberglass 玻璃丝force of buoyancy, buoyant force 浮力free surface 自由液面front elevation 正面图framing plan 船体构架图flanging machine 折边机fusion welding 熔焊fillet welding 角焊flat seam 对接缝flux 焊药filler metal; deposited metal 熔敷金属flooding test 灌水试验floodable length 可浸长度fracture 裂纹fatigue fracture 疲劳裂纹flexion 弯曲fractured 折裂fitted incorrectly 安装不正确（指小型的装置设备）failed (in failure) 失效fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）fouled 拥塞foul & dirty 闭塞fractured 折断finish machined 精加工fitted & scraped 拂刮fitted & ground 拂磨faired 拷平faired on 原地拷平faired in place 原地拷平F.P.T 尖舱F.W.T（K）淡水舱face plate 面板failed (in failure) 失效fair lead 导缆器faired 拷平faired in place 原地拷平faired on 原地拷平fatigue fracture 疲劳裂纹fender 碰垫；护舷材fender bar 护舷条ferry 渡轮ferry 渡船fiberglass 玻璃丝filler metal; deposited metal熔敷金属filler welded （填角）焊fillet welding 角焊finish machined 精加工fishing vessel(boat) 渔轮fitted & ground 拂磨fitted & scraped 拂刮fitted incorrectly 安装不正确（指小型的装置设备）fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）flame screen 防焰罩flange 折边flange 折边flanged bracket 折边肘板flanging machine 折边机flat bar 扁钢flat keel 平板龙骨flat plate 钢板flat seam 对接缝flexibility 挠性，柔性，易弯性flexion 弯曲FLG(flange) 法兰，折边（肘板）floatable length 可浸长度floating crane; derrick boat 起重船floating dock 浮船坞floating pitter; drive pitter 打桩船floodable length 可浸长度flooding test 灌水试验floor 肋板floor肋板flush deck ship 平甲板船flux 焊药folding door 折门force of buoyancy, buoyant force 浮力fore castle 艏楼fore peak tank（船的）首舱；前尖舱forecastle deck 艏楼甲板forging 锻件，锻造forward perpendicular 首垂线foul & dirty 闭塞fouled 拥塞foundation 底座foundation 基础，基座fracture 裂纹fractured 折断fractured 折裂frame 肋骨frame 肋骨frame number 肋骨跨数frame space 肋距framing plan 船体构架图free surface 自由液面freeboard 干舷freeing port 甲板排水孔；放水孔freight ferry 货物渡船fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线friability 易碎性front elevation 正面图fule oil 燃油full ahead 全速前进full astern 全速后退full-container ship 全集装箱船funnel 烟囱funnel 烟囱fusion welding 熔焊FX 艏楼Ggangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）gas turbine ship 燃气轮机船grain carrier 运粮船general cargo ship/vessel/carrier 杂货船guillotine shear 龙门剪床groove 槽沟grind 磨平general arrangement plan 总布置图grab dredger 抓斗挖泥船grooved 槽痕（比pitting深）gagged 塞口ground round 磨圆ground smooth 磨光ground & reamed 磨绞gagged 塞口galley 厨房gangway 走道，通道gangway (gang ladder or gang board) 舷梯gas turbine ship 燃气轮机船gasket 垫圈，垫料（集）密封垫general arrangement plan 总布置图general cargo ship杂货船general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grain carrier 运粮船grating 格子板；滑铁板GRD(girder) 纵桁grind 磨平groove 槽沟grooved 槽痕（比pitting深）grooving 开坡口ground & reamed 磨绞ground round 磨圆ground smooth 磨光ground tackle 锚泊索具guillotine shear 龙门剪床gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）Hhandrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度helm(rudder) pintle 舵销horizontal margin plate 水平内底边板high speed craft 高速船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线hopper barge 开底泥驳hairline fracture 发式裂纹half round steel 半圆钢high tensile steel 高强度钢heat treatment 热处理hardening 硬化，淬火hydraulic press 水压机half breadth plan 半宽水线图harbor tug 港作拖船hose test 冲水试验hydraulic test 水压试验hardness 硬度holed 穿洞holed & flooded 破洞浸水hair crack 发痕hair crack 发痕hairline fracture 发式裂纹half breadth plan 半宽水线图half round steel 半圆钢handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵harbor tug 港作拖船hardening 硬化，淬火hardness 硬度hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hatch; hatchway; hatch opening 舱口hawse 锚链孔hawse pipe 锚链管hawser 绳索；大缆heat treatment 热处理heaving 垂荡heel 踵材；横倾heeling angle 横倾角heeling moment 横倾力矩helm 舵helm(rudder) pintle 舵销high tensile steel 高强度钢hinged cover(door) 铰链盖（门）hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hold 货舱hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁holed 穿洞holed & flooded 破洞浸水hopper 漏斗，泥舱hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal girder 水平桁horizontal margin plate 水平内底边板horizontal margin plate 水平内底板horizontal stiffener 水平扶强材（防挠材）hose test 冲水试验hovercraft 气垫船hovercraft; aircushion craft 气垫船hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度hydraulic press 水压机hydraulic test 水压试验hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船hydrostatic curves 静水力曲线Iinner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板indent 凹痕，凹陷ice-breaker 破冰船intersection 交点；交叉；横断面impact test 冲击试验inland waterway vessel 内河船initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性I-Bar 工字钢inboard profile plan 纵剖面图intermittent welding 间断焊；断续焊in good condition 情况良好in poor condition 情况欠佳in bad condition 情况不佳，情况不良in a neglected condition 缺乏保养indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）inoperative 不能工作（失效）installed incorrectly 安装不正确（指较大的装置设备）it was obvious that this state had existed for a considerable time 损坏）状况是长期存在的incomplete 不齐全，不完整insufficient 不足in disorder 零乱（船属具零乱了）infiltrating (seeping) 渗漏I.A(O.A) angle 角钢ice-breaker 破冰船impact test 冲击试验in a neglected condition 缺乏保养in bad condition 情况不佳，情况不良in disorder 零乱（船属具零乱了）in good condition 情况良好in poor condition 情况欠佳inboard profile plan 纵剖面图incomplete 不齐全，不完整indent 凹痕，凹陷indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）infiltrating (seeping) 渗漏initial metacenter 初稳心initial stability 初稳性inland waterway vessel 内河船inlet 入口，插入物inner bottom 内底inner bottom plating 内底板inoperative 不能工作（失效）insert 挖补insert plate 嵌板；衬板installed incorrectly 安装不正确（指较大的装置设备）insubmersibility 抗沉性insufficient 不足intermittent welding 间断焊；断续焊intersection 交点；交叉；横断面it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的Jjack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机jacked 顶起（用千斤顶顶起）jack 千斤顶jack ladder 绳梯jacked 顶起（用千斤顶顶起）Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机Kkeel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板knuckle 折角线knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸keel 龙骨keel 龙骨keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelblock 龙骨墩keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板knocking 敲击knocking bearing 轴承敲缸knocking cylinder 敲缸knocking valve gear 伐件敲缸knuckle 折角线Llightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板lignumvitae 铁梨木liquefied gas barge 液化气体驳length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长loadline mark 载重水线标记low carbon steel 低碳钢lines plan 型线图lamellar tearing 层间撕裂lumber(timber) carrier 运木船liquid cargo ship 液体货货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船loaded waterline plane 满载水线图lap weld 搭接焊launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架laying off lofting 放样longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性loose engagement 啮合太松loose connection 接头松动loss of watertightness 失去水密性（比5好）loss of airtightness 失去气密性loss of oiltightness 失去油密性loss of lub-oil pressure 滑油压力降低loss of water pressure 水压力降低Loose 松动Leaking 漏logged (hourly) 记录（小时）lifted 抬升、举起lamellar tearing 层间撕裂lantern 信号灯lap weld 搭接焊lap welded 搭接焊launch 下水launching cradle 下水架launching grade 下水坡度launching ways 下水滑道laundry 洗衣间laying off lofting 放样Leaking 漏length between perpendicular 垂线间长length overall 总长lifted 抬升、举起lightening hole 减轻孔lignum vitae 铁梨木lignumvitae 铁梨木line 管系Linen 亚麻布lines plan 型线图liquefied natural gas tanker 液化天然气运输船liquefied petroleum gas tanker 液化石油气运输船liquid cargo ship液体货货船liquid chemical tanker 液体化学品船load waterline length 满载水线长loaded waterline plane 满载水线图loadline mark载重水线标记local strength 局部强度local stress 局部应力lofting 放样logbook 航海日志logged (hourly) 记录（小时）longitudinal 纵骨；纵材；纵桁longitudinal bending 纵向弯曲longitudinal bulkhead 纵舱壁longitudinal framing system 纵骨架式longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性longitudinal strength 纵向强度longitudinally framed ship 纵骨架式船Loose 松动loose connection 接头松动loose engagement 啮合太松loss of airtightness 失去气密性loss of lub-oil pressure 滑油压力降低loss of oiltightness 失去油密性loss of water pressure 水压力降低loss of watertightness 失去水密性（比5好）low carbon steel 低碳钢lug 耳板lumber(timber) carrier 运木船Mmud box 泥箱main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔manpowered boat 人力船motor sailor 机帆船multi-purpose ship 多用途船multi-purpose container ship 多用途集装箱船motor ship 内燃机船maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩midship section plan 舯剖面图mold loft floor 放样台mold loft 放样间mold loft batten, template batten 木样条marine slipway, railway dry dock 船排marine slipway cradle 船排支架mechanical property 机械性能missing 遗失measured & recorded 测量并记录machined 光车mica undercut 弧坑made to fit 拂合（装配好）MACH 机械，机器machined 光车made to fit 拂合（装配好）main deck 主甲板main frame 主肋骨man hole coaming 人孔围板man hole door 人孔盖maneuverability 操纵性manhole 人孔manhole 人孔manpowered boat 人力船manual welding 手工焊margin line 限界线margin plate 内底边板marine slipway cradle 船排支架marine slipway, railway dry dock 船排mast 桅measured & recorded 测量并记录mechanical property 机械性能messroom 杂物间，餐厅metacenter 稳心mica undercut 弧坑midship section plan 舯剖面图missing 遗失mold loft 放样间mold loft batten, template batten 木样条mold loft floor 放样台molded breadth 型宽molded depth 型深moment of inertia 惯性矩moment to change trim one centimeter 每厘米纵倾力矩mooring hole 导缆孔mooring post 系缆柱；岸柱motor sailor 机帆船motor ship内燃机船mud box 泥箱multi-purpose container ship 多用途集装箱船multi-purpose ship 多用途船navigation 航行，导航Nnon-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕nuclear-power ship 核动力船normalising 正火not properly serviced 未经正常保养not properly cleaned 未经正常清洁not properly protected未经正常保护not properly insulated未经正常隔热（或电气绝缘）not properly adjusted 未经正常校正not working 不能工作non-through crack 未穿透裂痕neglected 遗漏not watertight 不水密no…fitted, no…provided 未装no…available未备有neglected 遗漏no…available未备有no…fitted, no…provided 未装non-return valve 止回阀non-through crack 未穿透裂痕non-watertight bulkhead 非水密舱壁normalising 正火not properly adjusted 未经正常校正not properly cleaned 未经正常清洁not properly insulated 未经正常隔热（或电气绝缘）not properly protected 未经正常保护not properly serviced 未经正常保养not watertight 不水密not working 不能工作notch 切口；槽口；刻痕nuclear-power ship 核动力船Oooring post 系缆柱；岸柱oscillating load 振动负荷out bottom plating 外底板offset bulb plate 球扁钢ocean-going vessel 远洋船ore carrier 矿砂船oil barge 油驳oceanographic research vessel 海洋调查船ongitudinally framed ship 纵骨架式船oil tight test 油密试验oxy-acetylene welding 氧-乙炔焊out of action 停止工作（作用），不是指故障out of function 不能工作，失去作用，不起作用opened 开口oil polluted 油污染oil soaked 油浸oil stained 油渍。
船舶专用英语汇总
船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多•船舶专业英语词汇•船体制图常用英中名词术语对照•船舶英语(页1) - 设计学习- 千岛热线论....•船体结构英语•船舶英语手册1--5•Navis.gr - 3Examination Questions For...•船舶图纸符号大全•货运保险鉴定常用词汇。
船舶常用英语(一)汇总
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船第 1 页共24 页cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳. 专业.专注.hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长. 专业.专注.length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）. 专业.专注.bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器. 专业.专注.camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔. 专业.专注.duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟. 专业.专注.gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨. 专业.专注.keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板. 专业.专注.out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航. 专业.专注.sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算. 专业.专注.strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门. 专业.专注.weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料) T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力. 专业.专注.elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲. 专业.专注.lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差. 专业.专注.building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验. 专业.专注.pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度. 专业.专注.potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复. 专业.专注.12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start)不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammable vapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴. 专业.专注.4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲. 专业.专注.22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损. 专业.专注.7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热. 专业.专注.9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀. 专业.专注.14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊. 专业.专注.。
船舶常用英语（一）
pontoon catamaran
双体趸船
二、 船舶结构常用 英语
centerline
中心线，中线
athwartships 横对船体（与船首尾线直 交）
bevel
斜角；斜面
base line
基线
amidships
在船中部；在纵中线上
designed waterline breadth
tug; tugboat; towboat
拖船
harbor tug
港作拖船
rescuetug
救助拖轮
salvage ship
救捞船
dredger
挖泥船
trailing suction dredge
耙吸挖泥船
cuttersuction dredger
绞吸挖泥船
bucketwheel dredger
舭水泵
bilge strake(plate)
舭列板
bilge well
污水井
bitt
系缆桩
bollar d
系缆桩；系船柱；双系柱
bolster
枕垫
bonnet
烟囱帽；机罩
boom
杆；吊杆；桁；叉架
boom crutch(support; rest)
吊杆支架
bossing
尾管突出部；轴包套
bunker tank
燃料舱
bushing
衬套
butt
端接；残片
butt joint(seam)
平接缝
一、 船舶类型常用 英语
ship, vessel
船，船舶
常用船舶英语锦集
13、这根管子的通径是1500mm。 The diameter of this pipe is 1500mm.
14、这个系统的原理没有问题。 The principle of this system is okay.
23、消防管（压载管 / 日用空气管 / 日用淡水管）密性试验
The tightness test for fire pipes (ballast pipes / service air pipes / service F.W. pipes).
24、喷淋装置试验。 The test of spraying and flushing equipment.
4、Will this way take me to the foreign office? 外事办
5、Right-about-face向后转
Ⅲ Life in the yard
1、Have you got used to the life here?
2、Please hold the handrails well. 请抓好扶手
管座焊缝未焊透，需补焊打磨。
16、The seam of the reducer connection is not welded thoroughly and needs welding and grinding.
异径接头缝未焊透，需补焊打磨。
17、The seam of the bend is not welded thoroughly and requires welding and grinding.
船舶常用英语(一)
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker(LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage sh冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底、loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time（损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong …．(size, material, devices…）错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.repaired by welding 电焊修理2.welded 补焊、焊接3.closed up by welds （面积、深度、高度较大）焊补4.built up by welds 堆焊5.plug welded 塞焊6.spot welded 点焊7.butt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶常用英语(一)
船舶常用英语(一)一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipVLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighteraboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framingsystem 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member 构件structural strength结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语第 31 页共 45 页angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;第 32 页共 45 页list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim第 33 页共 45 页纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)第 34 页共 45 页失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未第 35 页共 45 页装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷第 36 页共 45 页10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕第 37 页共 45 页9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油第 38 页共 45 页漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked第 39 页共 45 页阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大第 40 页共 45 页16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)电弧mutator第 41 页共 45 页整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干A. Remove, crop etc.1.Removed第 42 页共 45 页拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮2.fitted & ground拂磨第 43 页共 45 页3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance第 44 页共 45 页校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊8 tackweld 点焊、平头焊、定位焊第 45 页共 45 页。
船舶行业常用英语
第一课船舶名称1．船舶工程Ship engineering2．船舶Ship, Vessel3．艇Boat, Craft4．商船Merchant ship, Commercial ship 5．运输船Transport ship6．客船Passenger ship7．客货船Passenger-cargo ship8．货船Cargo ship, Freighter, Cargo carrier 9．干货船Dry cargo ship10 杂货船General cargo ship11 多用途货船Multipurpose cargo ship12 散货船Bulk carrier, Bulk cargo ship13 运煤船Coal carrier14 运木船Timber carrier, Log carrier15 矿砂船Ore carrier16 液货船Tanker, Liquid cargo17 油船Oil tanker, Oil carrier18 成品油轮Product carrier19 穿梭油轮Shuttle tanker20 滚装船Roll on-Roll off ship, Ro-Ro ship21 集装箱船Container ship22 载驳船Barge carrier, Lighter aboard ship23 渡船Ferry24 驳船Barge, Lighter第二课船舶总布置甲板及舱室1，总布置General arrangement2，舱室布置Interior arrangement3，机舱布置Engine room arrangement6，舱室Space7，艏尖舱Fore peak8，艉尖舱After peak9，底边舱Bottom side tank10 顶边舱Top side tank11 边舱Wink tank12 底舱Hold13 双层底舱Double bottom tank14 深舱Deep tank15 甲板间舱Between deck space16 空隔舱Cofferdam17 罗经甲板Compass deck18 驾驶甲板Navigation deck, Bridge deck19 艇甲板Boat deck20 游步甲板Promenade deck21 起居甲板Accommodation deck22 直升机甲板Helicopter deck23 上甲板Upper deck24 起货机甲板Winch platform25 通道Passage, Alleyway26 内通道Interior alleyway27 外通道Exterior passage way28 跳板Ramp29 驾驶室Wheel house, Navigation bridge30 海图室Chart room31 报务室Radio room32 雷达室Radar room33 机舱Engine room36 锚链舱Chain locker37 舵机舱Steering engine room38 通风机室Fan room39 消防控制室Fire-control room40 桅室Mast room41 声呐室Sonar transducer space42 机修间Work shop43 起居舱室Accommodation living quarter44 居住舱室Cabin45 船长室Captain room46 大副室Chief officer room47 轮机长室Chief engineer room48 大管轮室First engineer room49 船员室Crew room50 客舱Passenger cabin51 货舱Cargo hold, Cargo space52 货油舱Cargo oil tank53 集装箱舱Container hold54 冷藏货舱Refrigerated cargo55 车辆舱Vehicle hold56 液化天然气舱Liquefied natural gas tank57 行李舱Luggage room58 液舱Liquid tank59 燃油舱Fuel oil tank60 滑油舱Lubricating oil tank61 污油舱Sludge tank, Dirty oil tank62 压载水舱Ballast water tank63 淡水舱Fresh water tank第三课基本投影面与船舶主要尺度1．船体型表面Molded hull surface2．型排水体积Hull volume3．中站面Mid-station plane4．基面Base plane5．中线面Center line plane6．基线Base line7．主尺度Principal dimensions8．总长Length overall9．最大长度Extreme length10 垂线间长Length between perpendiculars(Lpp)11 水线长Waterline length12 设计水线长Designed waterline length(Lwl)13 满载水线长Load waterline length14 型宽Molded breadth15 最大宽Extreme breadth16 型深Molded depth17 吃水Draft, Draught18 型吃水Molded draft19 设计吃水Designed draft20 结构吃水Scantling draft21 艏吃水Fore draft22 艉吃水After draft23 平均吃水Mean draft24 满载吃水Loaded draft25 型线图Lines plan26 艏垂线Forward perpendicular27 艉垂线After perpendicular28 站Ordinate station30 型线Molded lines31 型值表Table of offsets32 横剖面Transverse sections33 水线面Water plane34 纵剖面Longitudinal section35 梁拱Camber第四课油船外观,装置1．船首标志Head mark2．锚Anchor3．首吃水标志Forward draft mark 4．球鼻首Bulbous bow5．中部吃水标志Mid-ship draft mark 6．螺旋桨Propeller7．舵Rudder8．起锚机Windlass9．前桅Fore mast10 通风筒Ventilator11 十字缆柱Cross bite12 甲板部门仓库Deck store13 吊杆Derrick boom14 吊柱Derrick post15 天线桅Antenna pole16 救生艇Life boat17 桥楼Bridge18 雷达桅Radar mast19 烟囱Funnel20 舷梯Accommodation ladder21 货油装载站Loading station22 通用导缆器Universal chock24 货油舱口Cargo oil hatch25 货油管Cargo oil pipe1．球鼻首Bulbous bow2．首吃水标志Forward draft marks3．锚Anchor4．导缆钳Fair-lead5．苏伊士运河灯吊杆Suez canal projector davit 6．首旗杆Jack staff7．双柱系缆桩Ballard8．菌型通风筒Mushroom ventilator9．起锚机Windlass10 货油舱舱口Oil tight hatch11 干货舱舱口Dry cargo hatch12 绞车Winch13 桅Mast14 备用螺旋桨Spare propeller15 救生艇Lifeboat16 桥楼Bridge17 主罗经Standard compass18 雷达桅Radar mast19 吊杆柱Samson port20 走桥Gangway, Cat walk21 机舱天窗Engine room skylight22 舷梯Accommodation ladder23 舵Rudder24 螺旋桨Propeller25 隔离舱Cofferdam26 干货舱Dry cargo hold27 压载舱Ballast tank29 锅炉舱Boiler30 机舱Engine room31 泵舱Pump room32 喇叭型通风筒Cowl head ventilator33 辅机舱Auxiliary machinery room34 横舱壁Transverse bulk head36 尾轴Propeller shaft37 中间舱Center tank38 船底纵骨Bottom longitudinal39 舷側纵骨Side longitudinal40 纵舱壁Longitudinal bulkhead41 甲板纵骨Deck longitudinal42 舷侧肋骨Side transverse43 船底横骨（材）Bottom transverse44 横梁Transverse beam45 中内龙骨Center girder46 边舱撑材Strut47 龙骨Keel48 船底外板Bottom plating49 舭部外板Bilge strake50 舷侧外板Side plating51 舷顶列板Sheer strake第五课尾机型货船1. 舵Rudder2. 螺旋桨Propeller3. 尾锚，大流锚Stream anchor4. 舭龙骨Bilge keel5. 舷梯Accommodation ladder6. 绞缆机Mooring winch8. 导缆孔Fair-leader9. 蔬菜库Vegetable chamber10 天窗Skylight11 烟囱Funnel12 菌型通风筒Mushroom ventilator13 喇叭形通风筒Cowl head ventilator14 救生艇Lifeboat15 吊艇装置Lifting gear16 雷达桅Radar mast17 测向仪天线Direction finder antenna18 航迹灯Range light19 桅顶灯Mast head light20 舷灯Side light21 吊杆柱King post22 起货机Winch23 吊货杆Derrick boom24 吊杆柱Derrick post25 前桅Hatch26 货仓口On-deck girder第六课小型客货船1．螺旋桨Propeller2．尾柱Stern frame3．舵Rudder4．辅助船，小船，舢板Tender5．吊艇柱Boat davit6．尾灯Stern light7．旗杆Ensign staff8．吊锚杆Anchor davit9．导缆钳Fair-lead10 扇形格子Quadrant grating第七课定期客船第八课军舰装置1．首声纳Bow sona2．锚Anchor3．导缆钳和首旗杆Fair-lead & Jack staff4．挡浪板，防浪板Wave screen5．绞盘Capstan6．高平两用炮Dual purpose gun7．反潜火箭发射器ASROC Launcher8．带缆桩Bitt9．驾驶桥楼Navigation bridge10 高平两用炮中央瞄准仪Director for dual purpose gun11 火炮雷达Fire control system radar12 对空搜索雷达Air search radar13 水面警戒雷达Surface search radar14 烟囱Stack15 桁架桅Lattice mast16 小艇Cutter17 鱼雷发射管Anti-submarine torpedo tube18 鞭状天线Whip aerial19 探照灯Searchlight20 对空发射架Tarter launcher21 舭龙骨Bilge keel22 螺旋桨Propeller23 救生筏箱Life raft container24 舵Rudder25 对空导弹瞄准雷达Tarter anti-air missile guided radar第六课小型客货船1．螺旋桨Propeller2．尾柱Stern frame3．舵Rudder4．辅助船，小船，舢板Tender5．吊艇柱Boat davit6．尾灯Stern light7．旗杆Ensign staff8．吊锚杆Anchor davit9．导缆钳Fair-lead10 扇形格子Quadrant grating第七课定期客船第八课军舰装置1．首声纳Bow sona2．锚Anchor3．导缆钳和首旗杆Fair-lead & Jack staff4．挡浪板，防浪板Wave screen5．绞盘Capstan6．高平两用炮Dual purpose gun7．反潜火箭发射器ASROC Launcher8．带缆桩Bitt9．驾驶桥楼Navigation bridge10 高平两用炮中央瞄准仪Director for dual purpose gun11 火炮雷达Fire control system radar12 对空搜索雷达Air search radar13 水面警戒雷达Surface search radar14 烟囱Stack15 桁架桅Lattice mast16 小艇Cutter17 鱼雷发射管Anti-submarine torpedo tube18 鞭状天线Whip aerial19 探照灯Searchlight20 对空发射架Tarter launcher21 舭龙骨Bilge keel22 螺旋桨Propeller23 救生筏箱Life raft container24 舵Rudder25 对空导弹瞄准雷达Tarter anti-air missile guided radar第九课驱逐舰装置1．首旗杆Jack staff2．锚Anchor3．舱口Hatch4．挡（防）浪板Wave screen5．绞盘Capstan6．单管高射炮High angle gun7．反潜火箭ASROC (Anti-submarine rocket) 8．舷梯Accommodation ladder9．驾驶桥楼Navigation bridge10 机舱中央瞄准仪Direction for machine gun11 信号楼桥Flag deck12 对空搜索雷达Air search radar13 水面警戒雷达Surface search radar14 烟囱Stack15 桁架桅Lattice mast16 小艇Cutter17 鱼雷发射管Torpedo tube18 鞭状天线Whip aerial19 探照灯Searchlight20 吊车Crane21 舭龙骨Bilge keel22 声纳导流罩Sona dome23 救生筏Life raft24 整流尾鳍Skeg25 尾轴架Shaft bracket26 螺旋桨Propeller27 螺旋桨护栏Propeller guard28 舵Rudder29 带缆桩Bollard30 直升机库Helicopter hanger31 直升机甲板Helicopter deck32 闭式导缆钳Closed fair-lead33 导缆钳Fair-lead34 尾旗杆Ensign staff35 海军军旗Naval ensign第十课高速船第十一课船体结构名称1．中内龙骨Center girder2．旁内龙骨Side girder3．船底纵骨Bottom longitudinal4．内底纵骨Top longitudinal of double bottom 5．实肋板Solid floor6．龙骨底板Keel7．A列板，龙骨翼板 A strake8．船底外板Bottom plating9．舭列板Bilge strake10 舷侧外板Side plating11 舷顶次列板Top side strake12 舷顶列板Sheer strake13 内底板Inner bottom plating14 舭肋板Tank side bracket15 内底缘板扣板Gusset plate16 内舱肋骨Hold frame17 甲板间肋骨Between deck frame18 第二层甲板梁Second deck beam19 梁肘板Beam bracket20 第二层甲板Second deck21 上甲板Upper deck22 甲板边板Stringer plate23 肋骨肘板Tripping bracket24 强横梁Deck transverse beam25 甲板纵骨Deck longitudinal26 甲板纵桁Deck girder27 舱口围板Hatch coaming28 强横梁Strong beam29 强肋骨Web frame30 货仓支柱Hold pillar31 甲板间支柱Between deck pillar32 舷墙板Bulwark plate33 舷墙扶手Hand rail34 舷墙撑材Bulwark branchet35 水平防挠材Horizontal stiffener36 舭龙骨Bilge keel37 中肘板Docking bracket38 内底边板肘板Bracket to margin plate39 水密肋板Watertight floor40 水密肋板肘板Bracket to watertight floor41 垂直扶强材Vertical stiffener42 支柱Strut43 扇形孔，锯齿孔Scallop or Serration44 减轻孔Lightening hole45 内底边板Margin plate46 人孔Manhole47 水密舱壁Watertight bulkhead48 舱壁扶强材Bulkhead stiffener49 覆板Doubling第十二课艏部舣装1．起锚机Windlass2．锚链止动器Chain cable compressor 3．锚链筒Hawse pipe4．锚链Anchor chain5．双柱带缆桩Ballard6．导缆钳Fair-lead7．导缆孔Mooring pipe8．甲板端导缆滚轮Deck end roller9．钢索导轮Wire reel10 喇叭形通风筒Cow head ventilator11 吊货杆Derrick boom12 吊杆支托架Boom support13 通风测深管Air and sounding pipe14 旗杆Flag staff15 吊锚杆Anchor davit16 无杆锚Stockless anchor17 锚卸扣Anchor shackle18 锚柄Anchor shank , Anchor shall19 锚冠Anchor crown20 锚臂Anchor arm21 锚掌Anchor palm22 锚爪Anchor fluke23 停泊灯柱，锚灯柱Anchor light davit24 栅栏栏杆Open rail25 栏杆扶手Hand rail stanchion26 扶手Hand rail27 锚穴Anchor recess28 首导缆钳Bow chock29 锚链筒喇叭口Bell-mouth of hawse pipe30 锚链筒甲板法兰Deck flange of hawse pipe31 有杆锚Stock anchor32 燕尾锚33 锚杆Anchor stock34 系船浮筒35 刹车带Brake band36 主齿轮Main gear wheel37 链轮Gypsy wheel, star wheel38 制动器，刹车闸Brake39 带缆卷筒Warping drum40 汽缸Cylinder41 离合器控制杆Clutch lever第十三课房间内部舣装1．办公桌Desk2．转椅Revolving chair3．书柜Book case4．小橱End lock5．茶几Table6．角形沙发Sofa7．扶手软椅Arm chair8．方舷窗Square window9．台灯Desk light10 电话Telephone11 舷窗帘Curtain12 窗帘盒Curtain box13 时钟Clock14 舱顶灯Ceiling light15 扩散器Diffuser16 床Bed17 床头柜Bed side locker18 五屉柜Chest of drawer19 安乐椅Easy chair20 衣柜Wardrobe21 救生衣柜Life jacket locker22 镜子Mirror23 镜灯Mirror lamp24 床头灯Bed lamp25 衣帽挂钩Hat & coat hook26 梳妆柜Toilet locker27 洗脸盆Wash basin28舷窗Side scuttle29 书架Book rack30 防溅板Splash board31 水瓶架Bottle holder32 立柜Locker33 球形导向送风头Punkah louver34 餐桌Mess table35 椅子Mess chair36 带泄水槽的餐具柜Dresser with sink37 服务台Serving table38 食品柜Food locker39 餐具搁架Plate rack40 开水炉Water boiler41 水冷却器Water cooler42 电视机Television43 娱乐品小柜Game locker44 记事板Notice board45 合页Hinge46 锁孔板Escutcheon47 把手Handle48 橡皮密封圈Rubber seating ring49 风暴盖Dead light50 绞链Hinge51 舷窗Side light52 窗框Frame53 蝶形夹扣Butterfly clip54 舷窗Port or Scuttle55 玻璃Glass cover56 活动窗框Side light frame57 固定窗框Port frame58 滴水盒Saveall第十四课楼桥，驾驶室设备1．机舱传令钟Engine telegraph2．自动操舵仪Gyro pilot telemeter3．雷达显示器Radar indicator4．磁罗经Magnetic compass5．舵轮Steering wheel6．通航行桥楼的传声筒Voice tube to flying bridge 7．旋转了望窗Clever view screen8．号钟Signal bell9．液压遥控操舵器Transmitter, Telemeter10 船长Captain11 驾驶员Officer12 舵工Quarter master13 计程仪指示器Indicator of log14 雷达扫描装置Scanner of radar15 无线电测向仪16 汽笛拉线Wire of whistle17 扶手Hand rail18 导风板Wind screen19 六分仪Sextant20 起重柱Derrick post：：24 雷达Radar25 信号发送接收机Signal transmitter-receiver26 喇叭口Horn27 发射器Reflector28 波导管Wave guide29 扫描器传动装置Scanner drive assemble1．游标Index arm2．水平镜Horizontal glass3．色屏Shades4．动镜Index mirror5．手柄Handle6．望远镜Telescope7．弧形板Arc8．色屏Shades9．微调螺钉Tangent screw10 测微计Micrometer11 信号匹配显示器Signal matching indicator1．舵轮Steering wheel2．自动舵操舵台Gyro-pilot steering stand3．雷达显示器Radar indicator4．楼桥集中操纵台Bridge console stand5．投影磁罗经Projector compass6．连通上桥楼的传话筒Voice tube to flying bridge 7．旋转视窗Clear view screen8．信号钟Signal bell9．电话Telephone10 电罗经Gyro-compass11 记事板Blackboard12 舷侧出入口Outside doorway13 双筒望远镜Binoculars14 侧推器操纵手柄Side thruster lever15 可调螺距螺旋桨调节手柄CPP lever16 减摇鳍操纵台17 船长用送话器18 仪表板（发动机用）Gauge board(engine)19 仪表板（航海用）Gauge board(navigation)20 球形导向送风头Paunch louver21 室内灯Room light第十五课救生器材1．救生筏放置处Stowage position2．充气救生筏容器Survival pack3．绳梯Jumping ladder4．浮锚Sea anchor5．蓬架Arch6．浮体Buoyancy tube7．救生索Life line8．天棚Tent9．灯Light10 自动发烟式烟幕筒11 自燃灯Autolight lamp12 救生索Life line13 系绳栓及绳Toggle and line14 哨子Whistle15 充气阀Inflation valve16 气胀式救生筏Inflatable life-raft17 带格栅救生浮具Carley life float18 充气式救生衣Inflatable life jacket19 救生圈Life-buoy20 手持烟火信号Hand fire signal21 救生服Immersion suit22 救助艇Rescue boat23 耐火救生艇Fire-resistant lifeboat24 全封闭救生艇Totally enclosed lifeboat25 救生设备Life-saving appliance26 救生艇Lifeboat27 开敞式救生艇Open lifeboat28 部分封闭救生艇Partially enclosed lifeboat第十六课工人常用会话1．我是电工车间的工人。
船舶专用英语汇总
船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多∙船舶专业英语词汇∙船体制图常用英中名词术语对照∙船舶英语(页1) - 设计学习- 千岛热线论....∙船体结构英语∙船舶英语手册1--5.word可编辑.∙Navis.gr - 3Examination Questions For...∙船舶图纸符号大全∙货运保险鉴定常用词汇. 专业.专注.。
船舶英语词汇1
船舶英语词汇13-roller bending machine 三弯机abandon v. 弃船abolish v. 消除ABS 美国船级社acceleration n. 加速度accelerometer n. 加速度表accommodate v. 容纳accommodation deck起居(住舱)甲板accuracy n. 精度accurate synchro device准同步装置acetylene cutter 气割机acid-pickling n. 酸洗acoustics n. 音响效果adhesiveness n. 粘附力adjacent a.相邻的adjust v. 调节administration n. 行政管理admit v. 接纳adopt v. 采纳，采用affiliated factory 分厂，附属工厂aforementioned a.前述aft a. adv. n. （在）船艉aft peak 艉尖舱after service 售后服务ahead n. 正车air bottle 空气瓶air compressor 空压机air reservoir 气瓶air siren 汽笛air-tight test 气密实验alarm bell 警铃alignment n. 找中all waves 全波allowance n. 允值all position 全方位alternating current ( A.C.) 交流电ammonia n. 氨amplify v. 放大an automatic production line自动生产线analogous output 模拟输出analogue computer 模拟计算机anchor n. 锚anchor chain （cable chain）锚链anchor handling 锚操纵anchor windlass (chain windlass)起锚机anchorage buoy 系泊浮筒angular n. 角度antenna n. 天线anticorrosion precaution 防腐措施apparatus n. (pl. apparatus or apparatuses)仪器，器械，装置appearance n. 外观approval n. 批准，认可approve vt. 认可arbitrate v. 仲裁arc n. 弧度arduous a.艰难的arrange v. 布置，安排asbestos n. 石棉assemble v. 装配Assemble Language 汇编语言assembly n. 装配astern n. 倒车atmospheric survey 大气环流调查atomic power 原子能atomize v. 雾化authority n. 当局automatic control device自动控制装置automatic production line自动生产线automatic steering 自动操舵automatic submerged arc welding自动埋弧焊automatic telephone 自动电话aux. boiler 副锅炉aux. engine 辅机aux. engine room 辅机舱aux. machinery 辅机auxiliary means 辅助手段auxiliary system 辅助系统axial push 轴向推力backing n. 衬垫ballast piping 压载水管系ballast pump 压载泵ballast system 压载系统ballast water 压载水base n. 基准base point n. 基准点basic design 基本（方案）设计basic metal 母材battery unit 蓄电池组beam n. 波束beam n. 横梁bearing n. 轴承bearing hole n. 轴承孔bedplate n. 机座bell set 铃组bending machine 冷弯机berth n. (水平)船台，（船上）床铺berth or slipway fabrication船台装配bilge n. 舱底水bilge keel 舭龙骨bilge plate 舭板bilge pump 舱底水泵bilge system 舱底水系统binary system 二进位制blank n. 毛胚block n. 分段block or section fabrication分段或总段装配blood vessel 血管blower 风机blue collar worker 蓝领,工人boat deck 艇甲板bollard n. 带缆桩bolt n. 螺栓bolthead n. 螺栓头bottom n. 船底bottom plate 底板bottom structure 底板结构bow n. 船艏bow &stern structure 艏艉结构bow section 艏段branch company 分公司，子公司branch system 分系统bridge n. 桥楼bridge control 桥楼控制broadcast n. v. 广播broadcast station 广播站bronze sleeve 青铜套筒bulbous bow 球鼻艏bulk cargo 散装货物bulk-cargo carrier 散装货船bulkhead n. 隔舱壁bulkhead structure 隔舱壁结构bushing n. 衬垫butt joint 对接接头cabin n. 舱室cable fixture 电缆夹具calculation n. 计算calculator n. 计算器calibrate v. 校正calibration n. 校正cam n. 凸轮cam follower 凸轮附件camber n. 梁拱camshaft n. 凸轮轴capstan windlass（anchor winch）锚绞盘cargo n. 船货cargo oil 货油cargo –hold n. 货舱cargo-lifting n. 起货casing n. 罩壳cast iron piece 铸铁件casting n. 铸造cathode-ray type 阴极射线式CCS 中国船级社central control 集控centreline n. 中心线centrifugal a.离心的certificate n. 证书chain drive 链传动chain locker 锚链舱chain pipe 锚链管chain reaction 连锁反应chain stopper 制链器challenge n. v. 挑战chamfer v. 在边缘切斜面changeover switch 转换开关characteristics n.性能，特性，特征charge v. 充（电，气）check n. v. 检验chemical medium 化学介质China Classification Society(CCS)中国船级社China Ocean Shipping Company (COSCO) 中国远洋公司chip n. 芯片circle n. 圈子，团体class n. 船级classification n. 船级classification society 船级社cleanness n. 清洁度closed circulation 闭式循环clutch n. 离合器CO2 shielded arc welding 二氧化碳气体保护焊Coating n. 图层code n. 法典code display circuit 编码显示电路coefficients of ship form 船型系数cold processing 冷加工collision n. (船只)碰撞combustibility n. 可燃性combustion n. 燃烧combustion chamber 燃烧室combustion gas 燃气commanding telephone 指挥电话communication n. 通讯compartment n. 分隔舱compartment stuffing box隔舱填料函compass n. 罗经compass deck 罗经甲板compensate vt. 补偿competition n. 竞争completion drawing 完工图component n. 组成部分composition n. 成分组成compound excitation 复励comprehensive productivity综合生产能力compressed air 压缩空气compression (power)stroke n. 压缩冲程computer control console计算机控制台conceptual a. 概念的condensation n. 冷凝conductor n. 导体connecting rod 连杆connection n. 接头constant voltage 恒压constitute v. 构成consumables n. 消耗品consumption n. 消耗contact v. 触发container n. 集装箱continuous deck 连续甲板contract n. 合同contradiction n. 矛盾control component 控制元件control console 控制台control unit 控制装置converse method 反装法convertor n. 转换器conveyor n. 传送带coolant n. 致冷剂coolant(cooling agent)n. 制冷剂cooler n. 冷却器cooling system 冷却系统cooperation n. 合作coordinate n. 坐标core enterprise 核心企业corrosion n. 腐蚀corrugated a. 波纹状的course n. 航向cover n. 药皮CPP drive 可调浆传动crank cheek 曲柄夹板crankcase n. 曲柄箱crankpin n. 曲柄臂crankshaft n. 曲轴crankweb n. 曲柄臂crew n. (全体)船员cross section 截面crosshead n. 十字头cultivate v. 培养，培育current n. 电流current n. 洋流，水流current-impulse frequency convertor 电流-脉冲频率变换器curve n. 曲线cutting n. 切割cylinder n. 气缸cylinder block 气缸体cylinder cover (cylinder head) 缸盖cylinder liner 气缸衬套cylinder oil 气缸油cylinder wall 缸壁data impulse 数据脉冲davit n. 吊艇架deadweight ton(DWT) n.载重量，吨载量Decca receiver 台卡定位仪deck n. 甲板deck girder 甲板材deck longitudinal 甲板纵骨deck machinery 甲板机deck plate 甲板板deck structure 甲板结构deckhouse 甲板室deform v. 形变deliver v. 交货，交船delivery n. 交船，交货delivery ceremony 交船典礼derrick n. 吊杆design stage 设计阶段designation n. 名称，牌号designation n. 目的地detail design 详细（施工）设计detect v. 探测detect v. 侦察detection n. 探测deviation n. 位移dial n. 刻度盘diameter n. 直径differentia n. 差异digital computer 数字计算机digital output 数字输出direct current(D.C.)直流电direct drive 直接传动direct telephone对讲电话，直线电话directional finder 测向仪directional instrument 指向仪器directional stability 航向稳定性disc n. 圆盘discharge n. v. 排水dispensable a. 非必要的dispute n. v. 争端，争执distribute v. 分布distribute v. 分配，配电distribution n. 配电distribution box 分电箱最后由可爱的小金鲤于2007-08-13 11:44:43编辑casting n. 铸造cathode-ray type 阴极射线式CCS 中国船级社central control 集控centreline n. 中心线centrifugal a.离心的certificate n. 证书chain drive 链传动chain locker 锚链舱chain pipe 锚链管chain reaction 连锁反应chain stopper 制链器challenge n. v. 挑战chamfer v. 在边缘切斜面changeover switch 转换开关characteristics n.性能，特性，特征charge v. 充（电，气）check n. v. 检验chemical medium 化学介质China Classification Society(CCS)中国船级社China Ocean Shipping Company (COSCO) 中国远洋公司chip n. 芯片circle n. 圈子，团体class n. 船级classification n. 船级classification society 船级社cleanness n. 清洁度closed circulation 闭式循环CO2 shielded arc welding 二氧化碳气体保护焊Coating n. 图层code n. 法典code display circuit 编码显示电路coefficients of ship form 船型系数cold processing 冷加工collision n. (船只)碰撞combustibility n. 可燃性combustion n. 燃烧combustion chamber 燃烧室combustion gas 燃气commanding telephone 指挥电话communication n. 通讯compartment n. 分隔舱compartment stuffing box隔舱填料函compass n. 罗经compass deck 罗经甲板compensate vt. 补偿competition n. 竞争completion drawing 完工图component n. 组成部分composition n. 成分组成compound excitation 复励comprehensive productivity综合生产能力compressed air 压缩空气compression (power)stroke n.压缩冲程computer control console计算机控制台conceptual a. 概念的condensation n. 冷凝conductor n. 导体connecting rod 连杆connection n. 接头constant voltage 恒压constitute v. 构成consumables n. 消耗品consumption n. 消耗contact v. 触发container n. 集装箱continuous deck 连续甲板contradiction n. 矛盾control component 控制元件control console 控制台control unit 控制装置converse method 反装法convertor n. 转换器conveyor n. 传送带coolant n. 致冷剂coolant(cooling agent)n. 制冷剂cooler n. 冷却器cooling system 冷却系统cooperation n. 合作coordinate n. 坐标core enterprise 核心企业corrosion n. 腐蚀corrugated a. 波纹状的course n. 航向cover n. 药皮CPP drive 可调浆传动crank cheek 曲柄夹板crankcase n. 曲柄箱crankpin n. 曲柄臂crankshaft n. 曲轴crankweb n. 曲柄臂crew n. (全体)船员cross section 截面crosshead n. 十字头cultivate v. 培养，培育current n. 电流current n. 洋流，水流current-impulse frequency convertor 电流-脉冲频率变换器curve n. 曲线cutting n. 切割cylinder n. 气缸cylinder block 气缸体cylinder cover (cylinder head) 缸盖cylinder liner 气缸衬套cylinder oil 气缸油cylinder wall 缸壁data impulse 数据脉冲davit n. 吊艇架deadweight ton(DWT) n.载重量，吨载量Decca receiver 台卡定位仪deck n. 甲板deck girder 甲板材deck longitudinal 甲板纵骨deck machinery 甲板机deck plate 甲板板deck structure 甲板结构deckhouse 甲板室deform v. 形变deliver v. 交货，交船delivery n. 交船，交货delivery ceremony 交船典礼derrick n. 吊杆design stage 设计阶段designation n. 名称，牌号designation n. 目的地detail design 详细（施工）设计detect v. 探测detect v. 侦察detection n. 探测deviation n. 位移dial n. 刻度盘diameter n. 直径differentia n. 差异digital computer 数字计算机digital output 数字输出direct current(D.C.)直流电direct drive 直接传动direct telephone对讲电话，直线电话directional finder 测向仪directional instrument 指向仪器directional stability 航向稳定性disc n. 圆盘discharge n. v. 排水dispensable a. 非必要的dispute n. v. 争端，争执distribute v. 分布distribute v. 分配，配电distribution n. 配电distribution box 分电箱。
船舶常用英语一
船舶常用英语一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.S hipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.G eneral descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障 out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start)不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation ofinflammable vapors 可燃气体危险集积it was obvious that this state had existedfor a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering)（动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available 未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…) 错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.C rack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕 non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损 chopped off 崩缺fractured 折断19.knocking 敲击 knocking cylinder 敲缸 knocking valve gear 伐件敲缸 knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.B urning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑 rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光 undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线 adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.repaired by welding 电焊修理2.welded 补焊、焊接3.closed up by welds （面积、深度、高度较大）焊补4.built up by welds 堆焊5.plug welded 塞焊6.spot welded 点焊7.butt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
VTS常用船舶操纵英语 (1)
水域 外海航道 港内航道
港内
大型船 吃水的20％ 吃水的15％ 吃水的10％
VLCC 吃水的15％ 吃水的10％ 吃水的5％
马六甲海峡、新加坡海峡对吃水15M以上的船舶及 DW15万吨的以上的船舶过境时，规定了至少保持3。 5M富余水深。
日本濑户内海主要港口规定富余水深为10％ｄ＋50CM。
进出港安全操作： 船舶进出港时，船长应在驾驶台、轮机长应在机舱亲自指
挥操作； 港内航行时，不得超过规定的航速；不做不必要的追越；
避免在弯曲和复杂水域会船；充分考虑风流对船位的影响， 做到应急制动快，停得住； 进出港时，应在指定VHF工作频道守听并加强与交通管理 部门、港口的联系，听从其指挥调度，并做好协调与他船 的避让措施； 进出港时一旦发生险情或事故，应设法使船舶摆脱危险、 减少损失、 做好相关记录， 及时报告当地 海事部门。
14
一、船舶操纵基本术语及常识
航道富余水深 富余水深的的确定及富余水深应考虑的因素 前进中的船体下沉量 因波浪引起的摇荡、横摇、纵摇和垂荡使吃水
增加。 海图水深的测量误差 水位的变化量 为安全操船应考虑的因素
15
一、船舶操纵基本术语及常识
确定富余水深的实例
欧洲引水协会（EMPA），对进出阿母斯特丹等港口的 船舶，建议采用如下的富余水深。
2、IALA Recommendation V103 建议案（国际航标协会示范课程）规 定VTS操作员（operator）应接受8项基本训练：1、语言，2、交通管 理，3、设备操作，4、航海知识，5、沟通协调，6、无线电收发信息， 7、个人职务，8、紧急状况报告。
2
前言
3、《船舶交通管理系统运行管理规定》，交通部 安监字 【1997】375号 第三章 第十一条（五） 值班人员应……，能熟练使 用汉语普通话和英语标准用语与船舶通话。
船舶专业英语词汇
船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs一对立体投影相片abaft 朝向船尾[adv][prep]abandonment cost 船舶废置成本费用accommodation居住（舱室）living quarter accommodation ladder 舷梯adjust valve调节阀adjustable-pitch可调螺距式admiralty海军部advance coefficient进速系数aerostatic空气静力学的aft peak bulkhead艉尖舱壁aft peak tank艉尖舱aileron副鳍air cushion vehicle气垫船air diffuser空气扩散器air intake进气口aircraft carrier航空母舰air-driven water pump气动水泵airfoil气翼，翼剖面，机面，方向舵alignment chock组装校准用垫楔aluminum alloy structure铝合金结构American Bureau of Shipping美国船级社amidships舯[adv]amphibious两栖的anchor arm锚臂anchor chain锚链anchor crown锚冠anchor fluke锚爪anchor mouth锚唇anchor recess锚穴anchor shackle锚卸扣anchor stock锚杆angle bar角钢angle of attack攻角angle plate角钢angled deck斜角甲板anticipated loads encountered at sea在波浪中遭遇到的预期载荷anti-pitching fins减纵摇鳍antiroll fins减摇鳍anti-rolling tank减摇水舱appendage附体artisan技工assembly line装配流水线at-sea replenishment海上补给augment of resistance阻力增额auxiliary systems辅机系统auxiliary tank调节水舱axial advance轴向进速backing structure垫衬结构back-up member焊接垫板balance weight平衡锤ball bearing滚珠轴承ball valve球阀ballast tank压载水舱bar型材bar keel棒龙骨，方龙骨，矩形龙骨barge驳船baseline基线basic design基本设计batten压条，板条beam船宽，梁beam bracket横梁肘板beam knee横梁肘板Beacon 灯塔，示位标bed-plate girder基座纵桁bending-moment curves弯矩曲线Benoulli’s law伯努利定律berth term停泊期bevel折角bidder投标人bilge舭，舱底bilge bracket舭肘板bilge radius舭半径bilge sounding pipe舭部边舱水深探管bitt单柱系缆桩blade root叶跟blade section叶元剖面blast喷丸block coefficient方形系数blue peter出航旗boarding deck登艇甲板boat davit吊艇架boat fall吊艇索boat guy稳艇索bobstay首斜尾拉索body plan横剖面图bolt螺栓，上螺栓固定Bonjean curve邦戎曲线boom 吊杆boss螺旋桨轴榖bottom side girder旁底桁bottom side tank底边舱bottom transverse底列板boundary layer边界层bow line前体纵剖线bow wave艏波bowsprit艏斜桅bow-thruster艏侧推器box girder箱桁bracket floor框架肋板brake制动装置brake band制动带brake crank arm制动曲柄brake drum刹车卷筒brake hydraulic cylinder制动液压缸brake hydraulic pipe刹车液压管breadth extreme最大宽，计算宽度breadth molded型宽breakbulk件杂货breasthook艏肘板bridge桥楼，驾驶台bridge console stand驾驶室集中操作台BSRA英国船舶研究协会buckle屈曲buffer spring缓冲弹簧built-up plate section组合型材bulb plate球头扁钢bulbous bow球状船艏，球鼻首bulk carrier 散货船bulk oil carrier散装油轮bulkhead舱壁bulwark舷墙bulwark plate舷墙板bulwark stay舷墙支撑buoy tender航标船buoyant浮力的buoyant box浮箱Bureau Veritas法国船级社butt weld对缝焊接butterfly screw cap蝶形螺帽buttock后体纵剖线by convention按照惯例，按约定、公约船舶专业英语词汇（按照字母顺序排列）（二）cable ship布缆船cable winch钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing)计算机辅助制造CAM(computer-aided engineering)计算机辅助工程camber梁拱cant beam斜横梁cant frame斜肋骨cantilever beam悬臂梁capacity plan 舱容图CAPP(computer–aided process planning)计算机辅助施工计划制定capsize倾覆capsizing moment倾覆力臂captain 船长captured-air-bubble vehicle束缚气泡减阻船cargo cubic货舱舱容，载货容积cargo handling货物装卸carriage拖车，拖架cast steel stem post铸钢艏柱catamaran高速双体船catamaran双体的cavitation空泡cavitation number空泡数cavitation tunnel空泡水筒center keelson中内龙骨centerline bulkhead中纵舱壁centroid型心，重心，质心，矩心chain cable stopper制链器chart海图charterer租船人charterchief engineer轮机长chine舭，舷，脊chock导览钳CIM(computer integrated manufacturing)计算机集成组合制造circulation theory环流理论classification society船级社cleat系缆扣clipper bow飞剪型船首clutch离合器coastal cargo沿海客货轮cofferdam防撞舱壁combined cast and rolled stem混合型艏柱commercial ship营利用船commissary spaces补给库舱室，粮食库common carrier通用运输船commuter交通船compartment舱室，间隔舱compass罗经concept design概念设计connecting tank连接水柜constant-pitch propeller定螺距螺旋桨constraint condition约束条件container集装箱containerized集装箱化contract design合同设计contra-rotating propellers对转桨controllable-pitch可控螺距式corrosion锈蚀，腐蚀couple力矩，力偶crane克令吊，起重机crank曲柄crest(of wave)波峰crew quarters船员居住舱criterion判据，准则Critical Path Method 关键路径法cross-channel automobile ferries横越海峡车客渡轮cross-sectional area横剖面面积crow’s nest桅杆瞭望台cruiser stern巡洋舰尾crussing range航程cup and ball joint球窝关节curvature曲率curves of form各船形曲线cushion of air气垫damage stability破损稳性damper缓冲器damping 阻尼davit arm吊臂deadweight总载重量de-ballast卸除压载deck line at side甲板边线deck longitudinal甲板纵骨deck stringer甲板边板deck transverse强横梁deckhouse舱面室，甲板室deep v hull深v型船体delivery交船depth船深derrick起重机，吊杆design margin设计余量design spiral设计螺旋循环方式destroyer驱逐舰detachable shackle散合式连接卸扣detail design详细设计diagonal stiffener斜置加强筋diagram图，原理图，设计图diesel engine 柴油机dimensionless ratio无量纲比值displacement排水量displacement type vessel排水型船throughoutdistributed load分布载荷division站，划分，分隔do work做功dock泊靠vtdouble hook山字钩double iteration procedure双重迭代法double roller chock双滚轮式导览钳double-acting steam cylinder双向作用的蒸汽气缸down halyard降帆索draft吃水，草图，设计图drag阻力，拖拽力drainage排水draught吃水，草图，设计图，牵引力dredge挖泥船drift漂移，偏航drilling rig钻架drillship钻井船drive shaft驱动器轴driving gear box传动齿轮箱driving shaft system传动轴系dry dock干船坞ducted propeller导管螺旋桨dynamic supported craft动力支撑型船舶dynamometer测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p有效马力eccentric wheel偏心轮echo-sounder回声探深仪eddy漩涡eddy-making resistance漩涡阻力efficiency供给能力，供给量electrohydraulic电动液压的electroplater电镀工elevations高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula经验公式enclosed fabrication shop封闭式装配车间enclosed lifeboat封闭式救生艇end open link末端链环end shackle末端卸扣endurance续航力endurance续航力，全功率工作时间engine room frame机舱肋骨engine room hatch end beam机舱口端梁ensign staff船尾旗杆entrance 进流段erection装配，安装exhaust valve排气阀expanded bracket延伸肘板expansion joint伸缩接头extrapolate外插fair光顺faised floor升高肋板fan鼓风机fatigue疲劳feasibility study可行性研究feathering blade 顺流变距桨叶fender护舷ferry渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set鳍角反馈装置fine fast ship 纤细高速船fine form瘦长船型finite element有限元fire tube boiler火管锅炉fixed-pitch固定螺距式flange突边，法兰盘flanking rudders侧翼舵flap-type rudder襟翼舵flare外飘，外张flat of keel平板龙骨fleets of vessels船队flexural挠曲的floating crane起重船floodable length curve可进长度曲线flow of materials 物流flow pattern流型，流线谱flush deck vessel平甲板型船flying bridge游艇驾驶台flying jib艏三角帆folding batch cover折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship后续船foot brake 脚踏刹车fore peak tank 艏尖舱forged steel stem锻钢艏柱forging锻件，锻造forgeforward draft mark船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder前/后肩foundry casting翻砂铸造frame船肋骨，框架，桁架freeboard干舷freeboard deck干舷甲板freight rate运费率fresh water loadline淡水载重线frictional resistance摩擦阻力Froude number 傅汝德数fuel/water supply vessel油水供给船full form 丰满船型full scale全尺度fullness丰满度funnel烟囱furnishings内装修furniture gaff纵帆斜桁gaff foresail前桅主帆gangway舷梯gantt chart甘特图gasketed openings装以密封垫的开口general arrangement 总布置general cargo ship杂货船generatrix母线geometrically similar form外形相似船型girder桁梁，桁架girder of foundation基座纵桁governmental authorities政府当局，管理机构gradient梯度graving dock槽式船坞Green Book绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton长吨（1.016公吨）group technology成祖建造技术GT成组建造技术guided-missile cruiser导弹巡洋舰gunwale船舷上缘gunwale angle舷边角钢gunwale rounded thick strake舷边圆弧厚板guyline定位索gypsy链轮gyro-pilot steering indicator自动操舵操纵台gyroscope回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan半宽图half depth girder半深纵骨half rounded flat plate半圆扁钢hard chine尖舭hatch beam sockets舱口梁座hatch coaming舱口围板hatch cover舱口盖hatch cover舱口盖板hatch cover rack舱口盖板隔架hatch side cantilever舱口悬臂梁hawse pipe锚链桶hawsehole锚链孔heave垂荡heel横倾heel piece艉柱根helicoidal螺旋面的，螺旋状的hinge铰链hinged stern door艉部吊门HMS英国皇家海军舰艇hog中拱hold船舱homogeneous cylinder均质柱状体hopper barge倾卸驳horizontal stiffener水平扶强材hub桨毂，轴毂，套筒hull form船型，船体外形hull girder stress船体桁应力HVAC(heating ventilating and cooling)取暖，通风与冷却hydraulic mechanism液压机构hydrodynamic水动力学的hydrofoil水翼hydrostatic水静力的IAGG(interactive computer graphics)交互式计算机图像技术icebreaker破冰船icebreaker破冰船IMCO(Intergovernmental Maritime Consultative Organization)国际海事质询组织immerse浸水，浸没impact load冲击载荷imperial unit英制单位in strake内列板inboard profile纵剖面图incremental plasticity增量塑性independent tank独立舱柜initial stability at small angle of inclination小倾角初稳性inland waterways vessel内河船inner bottom内底in-plane load面内载荷intact stability完整稳性intercostals肋间的，加强的International Association of Classification Society(IACS) 国际船级社联合会International Towing Tank Conference(ITTC)国际船模试验水池会议intersection交点，交*，横断（切）inventory control存货管理iterative process迭代过程jack船首旗jack千斤顶joinery细木工keel龙骨keel laying开始船舶建造kenter shackle双半式连接链环Kristen-Boeing propeller正摆线推进器landing craft登陆艇launch发射，下水launch汽艇launching equipment（向水中）投放设备LCC大型原油轮leading edge导缘，导边ledge副梁材length overall总长leveler调平器，矫平机life saving appliance救生设备lifebuoy救生圈lifejacket救生衣lift fan升力风扇lift offsets量取型值light load draft空载吃水lightening hole 减轻孔light-ship空船limbers board舭部污水道顶板liner trade定期班轮营运业lines型线lines plan型线图Linnean hierarchical taxonomy林式等级式分类学liquefied gas carrier液化气运输船liquefied natural gas carrier液化天然气船liquefied petroleum gas carrier液化石油气船liquid bulk cargo carrier液体散货船liquid chemical tanker液体化学品船list倾斜living and utility spaces居住与公用舱室Lloyd’s Register of shipping劳埃德船级社Lloyd’s Rules劳埃德规范Load Line Convention载重线公约load line regulations载重线公约，规范load waterplane载重水线面loft floor放样台longitudinal(transverse)纵（横）稳心高longitudinal bending纵总弯曲longitudinal prismatic coefficient纵向菱形系数longitudinal strength纵总强度longitudinally framed system纵骨架式结构luffing winch变幅绞车machinery vendor机械（主机）卖方magnet gantry磁力式龙门吊maiden voyage处女航main impeller主推叶轮main shafting主轴系major ship大型船舶maneuverability操纵性manhole人孔margin plate边板maritime海事的，海运的，靠海的mark disk of speed adjusting速度调整标度盘mast桅杆mast clutch桅座matrix矩阵merchant ship商船Merchant Shipbuilding Return商船建造统计表metacenter稳心metacentric height稳心高metal plate path金属板电镀槽metal worker金属工metric unit公制单位middle line plane中线面midship section舯横剖面midship section coefficient中横剖面系数ML物资清单，物料表model tank船模试验水池monitoring desk of main engine operation主机操作监视台monitoring screen of screw working condition螺旋桨运转监视屏more shape to the shell船壳板的形状复杂mould loft放样间multihull vessel多体船multi-purpose carrier多用途船multi-ship program多种船型建造规划mushroom ventilator蘑菇形通风桶mutually exclusive attribute相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C数值控制nautical mile海里naval architecture造船学navigation area航区navigation deck航海甲板near-universal gear准万向舵机，准万向齿轮net-load curve静载荷曲线neutral axis中性轴，中和轴neutral equilibrium中性平衡non-retractable fin stabilizer不可收放式减摇鳍normal法向的，正交的normal operating condition常规运作状况nose cone螺旋桨整流帽notch开槽，开凹口oar橹，桨oblique bitts斜式双柱系缆桩ocean going ship远洋船off-center loading偏离中心的装载offsets型值offshore drilling离岸钻井offshore structure离岸工程结构物oil filler加油点oil skimmer浮油回收船oil-rig钻油架on-deck girder甲板上桁架open water敞水optimality criterion最优性准则ore carrier矿砂船orthogonal矩形的orthogonal正交的out strake外列板outboard motor舷外机outboard profile侧视图outer jib外首帆outfit舾装outfitter舾装工outrigger舷外吊杆*头overall stability总体稳性overhang外悬paddle桨paddle-wheel-propelled明轮推进的Panama Canal巴拿马运河panting arrangement强胸结构，抗拍击结构panting beam强胸横梁panting stringer抗拍击纵材parallel middle body平行中体partial bulkhead局部舱壁payload有效载荷perpendicular柱，垂直的，正交的photogrammetry投影照相测量法pile driving barge打桩船pillar支柱pin jig限位胎架pintle销，枢轴pipe fitter管装工pipe laying barge铺管驳船piston活塞pitch螺距pitch纵摇plan views设计图planning hull滑行船体Plimsoll line普林索尔载重线polar-exploration craft极地考察船poop尾楼port左舷port call沿途到港停靠positive righting moment正扶正力矩power and lighting system动力与照明系统precept技术规则preliminary design初步设计pressure coaming阻力式舱口防水挡板principal dimensions主尺度Program Evaluation and Review Technique规划评估与复核法progressive flooding累进进水project探照灯propeller shaft bracket尾轴架propeller type log螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant舵柄quality assurance质量保证quarter居住区quarter pillar舱内侧梁柱quartering sea尾斜浪quasi-steady wave准定长波quay码头，停泊所quotation报价单船舶专业英语词汇（按照字母顺序排列）（六）racking倾斜，变形，船体扭转变形radiography X射线探伤raked bow前倾式船首raster光栅refrigerated cargo ship冷藏货物运输船Register（船舶）登录簿，船名录Registo Italiano Navade意大利船级社regulating knob of fuel pressure燃油压力调节钮reserve buoyancy储备浮力residuary resistance剩余阻力resultant合力reverse frame内底横骨Reynolds number雷诺数right-handed propeller右旋进桨righting arm扶正力臂，恢复力臂rigid side walls刚性侧壁rise of floor底升riverine warfare vessel内河舰艇rivet铆接，铆钉roll横摇roll-on/roll-off(Ro/Ro) 滚装rotary screw propeller回转式螺旋推进器rounded gunwale修圆的舷边rounded sheer strake圆弧舷板rubber tile橡皮瓦rudder舵rudder bearing舵承rudder blade舵叶rudder control rod操舵杆rudder gudgeon舵钮rudder pintle舵销rudder post舵柱rudder spindle舵轴rudder stock舵杆rudder trunk舵杆围井run去流段sag中垂salvage lifting vessel救捞船scale缩尺，尺度schedule coordination生产规程协调schedule reviews施工生产进度审核screen bulkhead轻型舱壁Sea keeping performance耐波性能sea spectra海浪谱sea state海况seakeeping适航性seasickness晕船seaworthness适航性section moulus剖面模数sections剖面，横剖面self-induced自身诱导的self-propulsion自航semi-balanced rudder半平衡舵semi-submersible drilling rig半潜式钻井架shaft bossing轴榖shaft bracket轴支架shear剪切，剪力shear buckling剪切性屈曲shear curve剪力曲线sheer舷弧sheer aft艉舷弧sheer drawing 剖面图sheer forward艏舷弧sheer plane纵剖面sheer profile总剖线sheer profile纵剖图shell plating船壳板ship fitter船舶装配工ship hydrodynamics船舶水动力学shipway船台shipyard船厂shrouded screw有套罩螺旋桨，导管螺旋桨side frame舷边肋骨side keelson旁内龙骨side plate舷侧外板side stringer甲板边板single-cylinder engine单缸引擎sinkage升沉six degrees of freedom六自由度skin friction表面摩擦力skirt（气垫船）围裙slamming砰击sleeve套管，套筒，套环slewing hydraulic motor 回转液压马达slice一部分，薄片sloping shipway有坡度船台sloping top plate of bottom side tank底边舱斜顶板slopint bottom plate of topside tank定边舱斜底板soft chine圆舭sonar声纳spade rudder悬挂舵spectacle frame眼睛型骨架speed-to-length ratio速长比sponson deck舷伸甲板springing颤振stability稳性stable equilibrium稳定平衡starboard右舷static equilibrium静平衡steamer汽轮船steering gear操纵装置，舵机bow 船艏stem contour艏柱型线stern船艉stern barrel尾拖网滚筒stern counter尾突体stern ramp尾滑道，尾跳板stern transom plate尾封板stern wave艉波stiffen加劲，加强stiffener扶强材，加劲杆straddle跨立，外包式叶片strain应变strake船体列板streamline流线streamlined casing流线型套管strength curves强度曲线strength deck强力甲板stress concentration应力集中structural instability结构不稳定性strut支柱，支撑构型subassembly分部装配subdivision分舱submerged nozzle浸没式喷口submersible潜期suction back of a blade桨叶片抽吸叶背Suez Canal tonnage苏伊士运河吨位限制summer load water line夏季载重水线superintendent监督管理人，总段长，车间主任superstructure上层建筑Supervision of the Society’s surveyor船级社验船师的监造书supper cavitating propeller超空泡螺旋桨surface nozzle水面式喷口surface piercing穿透水面的surface preparation and coating表面加工处理与喷涂surge纵荡surmount顶上覆盖，越过swage plate压筋板swash bulkhead止荡舱壁SWATH(Small Waterplane Area Twin Hull)小水线面双体船sway横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor尾翼式锚talking paper讨论文件tangential切向的，正切的tangential viscous force切向粘性力tanker油船tee T型构件，三通管tender交通小艇tensile stress拉（张）应力thermal effect热效应throttle valve节流阀throughput物料流量thrust推力thruster推力器，助推器timber carrier木材运输船tip of a blade桨叶叶梢tip vortex梢涡toed towards amidships趾部朝向船舯tonnage吨位torpedo鱼雷torque扭矩trailing edge随边transom stern方尾transverse bulkhead plating横隔舱壁板transverse section横剖面transverse stability横稳性trawling拖网trial实船试验trim纵倾trim by the stern/bow艉艏倾trimaran三体的tripping bracket防倾肘板trough波谷tugboat拖船tumble home（船侧）内倾tunnel wall effect水桶壁面效应turnable blade可转动式桨叶turnable shrouded screw转动导管螺旋桨tweendeck cargo space甲板间舱tweendedk frame甲板间肋骨two nodded frequency双节点频率ULCC超级大型原油轮ultrasonic超声波的underwriter（海运）保险商unsymmetrical非对称的upright position正浮位置vapor pocket气化阱ventilation and air conditioning diagram通风与空调铺设设计图Venturi section文丘里试验段vertical prismatic coefficient横剖面系数vertical-axis(cycloidal)propeller直叶（摆线）推进器vessel component vender造船部件销售商viscosity粘性VLCC巨型原油轮very large crude carrierVoith-Schneider propeller/propulsion外摆线直翼式推进器v-section v型剖面wake current伴流，尾流water jet喷水（推进）管water plane水线面watertight integrity/integrality水密完整性integrate 整合completenesswave pattern波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck露天甲板web腹板web beam强横梁web frame腹肋板welder焊工melterwetted surface 湿表面积winch绞车mooring winchwindlass起锚机anchor windlasswing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance有效使用修正量worm gear蜗轮，蜗杆yacht快艇yard issue船厂开工任务发布书yards帆桁yaw首摇二．轮机1．Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).螺旋桨轴（中间轴）机加工尺寸检查。
船舶常用英语
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
motor ship内燃机船
diesel ship柴油机船
electrically-propelled ship电力推进船
steam turbine ship汽轮机船
gas turbine ship燃气轮机船
nuclear-power ship核动力船
deck ship甲板船
inland waterway vessel内河船
civil ship; merchant ship民用船；商船
transport ship运输船
pleasure yacht游艇
passenger ship客船
coasting passenger and cargo ship沿海客货船
passenger and auto-car carrier旅客及汽车运输船
RO/RO barge滚装驳船
liquefied gas barge液化气体驳
hopper barge开底泥驳
split hopper barge对开泥驳
pusher; pushboat顶推船；推船
working ship工程船
tug; tugboat; towboat拖船
harbor tug港作拖船
bilge strake(plate)舭列板
bilge well污水井
bitt系缆桩
bollard系缆桩；系船柱；双系柱
bolster枕垫
bonnet烟囱帽；机罩
boom杆；吊杆；桁；叉架
boom crutch(support; rest)吊杆支架
bossing尾管突出部；轴包套
bottom frame船底横骨
vehicle-passenger ferry catamaran双体车客渡船
pontoon catamaran双体趸船
二、船舶结构常用英语
center line中心线，中线
athwartships横对船体（与船首尾线直交）
bevel斜角；斜面
base line基线
amidships在船中部；在纵中线上
flush deck ship平甲板船
raised quarter-deck ship尾升高甲板船
well-deck ship半舱船
single side ship单舷长大舱口船
three-island ship三岛式船
double shell ship双壳船
riveted ship铆接船
welded ship焊接船
multi-purpose container ship多用途集装箱船
general cargo ship/vessel/carrier杂货船
bulk (cargo) carrier散货船
ore carrier矿砂船
grain carrier运粮船
coal carrier; coaler运煤船
lumber(timber) carrier运木船
barge carrier; lighter aboard ship(LASH)载驳船
barge; lighter驳船
deck barge甲板驳
well-deck barge半舱驳
double shell barge双壳驳
single side barge单舷长大舱口驳
oil barge油驳
container barge集装箱驳船
designed waterline breadth设计水线宽
designed waterline length设计水线长
draft吃水
former/aft draft首/尾吃水
draft figures吃水尺度
intersection交点；交叉；横断面
knuckle折角线
length between perpendicular垂线间长
bulb stern球形船尾
bulkhead舱壁
bulkhead plating舱壁板
bulkhead stiffener舱壁扶强材
bulwark舷墙
bulwark plating舷墙板
bulwark stay舷墙扶强材
bunker tank燃料舱
bushing衬套
butt端接；残片
butt joint(seam)平接缝
capstan绞盘；绞缆机
cargo batten货舱护板
cargo block吊货滑车
cargo port装货舷梯，舷门
cat walk（油轮上的）天桥，步桥
center girder中底桁
center strake中央内底板
chafing plate防擦板
chafing ring防擦环
chain lock(well)锚链舱
cattle carrier运牲畜船
multi-purpose ship多用途船
liquid cargo ship液体货货船
chemical tank化学品液货船
liquid chemical tanker液体化学品船
liquefied gas carrier液化气体船
liquefied petroleum gas tanker(LPG)液化石油气运输船
liquefied natural gas tanker (LNG)液化天然气运输船
tanker; oil tanker油轮
super tanker超级油轮
VLCC (very large crude carrier) (吨位在20万至30万吨之间的)巨型油轮
ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的)超巨型油船
length overall总长
load waterline length满载水线长
register length (breadth; depth)登记长度（宽度、深度）
freeboard干舷
rise of floor (dead; rise)舭高；船底、
loadline mark载重水线标记
fresh water load line (F.)淡水载重线
refrigerated ship; cold storage sh冷藏船
roll-on/roll-off ship (RO/RO ship)滚装船
ferry渡船
passenger ferry旅客渡船
freight ferry货物渡船
fishing vessel(boat)渔轮
trawler拖网渔轮
一、船舶类型常用英语
ship, vessel船，船舶
boat, craft艇
sampan舢板,小船
manpowered boat人力船
sailor; sailing boat帆船
motor sailor机帆船
power-driven ship机动船
paddle steamer, paddle wheel vessel明轮船
screw ship; propeller vessel螺旋桨船
airscrew ship; aerial propeller vessel空气螺旋桨船
hovercraft; aircushion craft气垫船
hydrofoil水翼船
hydrojet propelled boat, water jet boat喷水船
fresh water timber load line (L.F.)淡水木材载重线
tropical fresh water load line (TF)热带淡水载重线
tropical load line (T)热带载重线
summer load line(S)夏季载重线
summer freshwater load line(F)夏季淡水载重线
bottom longitudinal船底纵骨
bottom plate船底板
bow船首，船头
bow fender艏护垫
bow flare艏部外飘
bow thruster首侧推器
bracket肘板；（三角）拖架
breakwater挡浪板
bridge桥；桥楼；驾驶台
bulb angle圆头角材
bulbous bow球形船首，球鼻首
winter load line(W)冬季载重线
winter North Atlantic load line(WNA)冬季北大西洋载重线
even keel（首尾）等吃水，平载
extreme breadth最大宽度
floatable length可浸长度
sheer at forward (after) perpendicular首尾舷弧
sheer line舷弧线
accommodation居住舱室
accommodation deck起居舱室；旅客甲板accommodation ladder舷梯
accommodation ladder on ladder manrope舷梯扶索
after body后（部船）体
after peak bulkhead艉尖舱舱壁
after peak tank艉尖舱
air hole空气孔
air pipe空气管
appendage（船体水线下的）附体；附件
auxiliary machinery辅助机械；辅机
balanced rudder平衡舵
ballast压载（物）
ballast line压载水管系
transversely framed ship横骨架式船
longitudinally framed ship纵骨架式船
combined framed ship混合骨架式船