亚德客过滤器BF3000选型手册
产品选型手册
SISB3-PTCH-00B 日期：2007-08-15 1概述SB3000系列隔离安全栅通过光、电、磁等隔离技术对供电电源、输入端信号和输出端信号三者进行两两隔离，从而实现现场设备和控制系统之间的隔离信号传输，是现场设备和控制室设备间的隔离接口单元；隔离技术对输入输出信号在电气上进行完全隔离，大大提高电子系统的抗干扰性和可靠性，目前越来越多的工业控制系统和现场设备间的接口采用隔离接口单元取代原来的非隔离单元。
SB3000系列隔离安全栅按GB3836.4-2000设计，除了具有隔离功能外，还带有相关限压、限流元件，具有防爆功能，它安装在安全场所，与安装在危险场所的本质安全防爆设备共同组成本质安全防爆系统。
利用内部的隔离器件、限压、限流元件来限制流向危险区的故障能量，从而保证危险场所的电器设备和人身的安全。
SB3000系列隔离式安全栅还增加了相应的信号转换变送线路，将现场的不同物理量信号调理转换成标准信号，即涵盖了以下设备的功能：热电阻温度信号变送器、毫伏信号变送器、热电偶温度信号变送器、配电器、中间驱动继电器。
特 点•[Ex ia ]ⅡC防爆等级，可适用于最危险的0区危险场所及最危险介质。
•输入/输出信号及电源三端口隔离，构成全浮空系统，无须操心工业现场复杂的工频干扰、共模干扰等，极大地简化现场问题的处理。
•无需高度完善的接地，相关现场设备可视情况接地或不接地，消除接地回路带来的干扰•隔离电压高•隔离故障点，将调试维护过程中可能出现的故障隔离在一个点上，避免由于一个点的故障影响整个系统，即使当遭受如雷击等意外时，亦可最大限度避免系统大面积瘫痪。
•DIN导轨独立安装•高密度安装，提高系统装置的集成度。
•高转换精度•模块系列化，信号隔离、配电、放大调理变换功能覆盖了过程控制中最广泛之需求，简化设计。
•模块内带保护电路并有工作状态指示•端子“即插即用”，各端子可带电热插拔，便于安装维护。
•结构小巧紧凑，顺应现代控制系统密集安装要求，节省机柜空间。
亚德客二联件BFC3000选型手册
产品名称:亚德客二联件BFC3000选型手册
有些品牌的电磁阀和气缸能够实现无油润滑（靠润滑脂实现润滑功能），便不需要使用油雾器！过滤度一般为50-75μm，调压范围为0.5-10Mpa，如需过滤精度为5-10μm，10-20μm，25-40μm，及调压为0.05-0.3Mpa，0.05-1Mpa二大件无管连接而成的组件称为二联件。
二大件是多数气动系统中不可缺少的气源装置，安装在用气设备近处，是压缩空气质量的最后保证。
三大件的安装顺序依进气方向分别为空气过滤器、减压阀和油雾器。
空气过滤器和减压阀组合在一起可以称为气动二联件。
有些场合不能允许压缩空气中存在油雾，则需要使用油雾分离器将压缩空气中的油雾过滤掉。
Parker Pneumatic 一般工业氩滤芯说明书
P3N Miniature Prep-Air II Global Air Preparation Products
Material specifications
Description Baffle Body Bowl Deflector Filter element
Pressures over 150 PSIG
Auto internal drain 1/8" with 1/2" drain plate 1/2 NPT tapped port 0.01 micron 1.0 micron Adsorber
.55 (14)
35F (Hi-Flow) DP2-02-001 GRP-95-022 DP3-01-000 P32KA00DA GRP-95-392 GRP-95-393 MTP-95-502 MSP-95-502 MXP-95-502
Part number (NPT) Automatic drain 35F77EAP 35F77HAP 35F87EAP 35F87HAP 43FN7EAP 43FN7HAP
Industrial
Separators Proportional Steel
Bulk Liquid Precision / Stainless General
43F (Hi-Flow) DP2-02-001 GRP-95-022 DP3-01-000 P32KA00DA GRP-95-392 GRP-95-393 MTP-95-562 MSP-95-876 MXP-95-565
General Stainless Precision / Bulk Liquid
Parker Hannifin 微型空气过滤器 PF504 产品选择手册说明书
Ordering InformationBOLD ITEMS ARE MOST POPULAR.AutomaticDrainManualDrainPF504 Series1/4 Inch PortsCatalog 0700P-EMiniature PF504 SeriesPF504 FilterDimensionsA1.56(40)C0.31(8)D3.69(94)E4.00(102)F1.58(40)inches(mm)Standard part numbers shown bold.For other models refer to ordering information below.SCFM = Standard cubic feet per minute at 90 PSIG inlet and 5 PSIGpressure drop.PortSizeNPT BSPPManual Twist Drain Manual Twist Drain1/4"PF504-02DHSS PF504G02DHSSFeatures• Stainless steel construction handlesmost corrosive environments.• Fluorocarbon seals standard.• Meets NACE specificationsMR-01-75/ISO 15156.• 1/8" female threaded drain.• High Flow: 1/4" - 23 SCFM§Port Type- NPTG BSPPPort Size02 1/4 InchBowlD Metal BowlwithoutSight GaugeElementH 20 MicronG 5 MicronMaterialSS Stainless SteelPF504 - 02 D H SSOptionsBlank ManualTwist DrainR AutomaticPulse DrainFlow - dm /sP r e s s u r e D r o p - b a r3nPrimary Pressure - PSIG1.7 bar3.4 bar 5.2 bar 6.9 bar Primary Pressure - barPF504 Series Air Line FiltersCatalog 0700P-E Technical Specifications – PF504PF504 Filter Kits & AccessoriesDrain Kits –Automatic Pulse Drain ................................................RK504SY -SS Manual Twist Drain–Small (Old) ..........................................................SA600Y7-1SS Large (New) ...............................................................SAP05481Filter Element Kits –Particulate (5 Micron) .......................................................EK504VY Particulate (20 Micron) .......................................................EK504Y Pipe Nipple –1/4" 316 Stainless Steel ................................................616Y28-SSSpecificationsBowl Capacity ..................................................................1.0 Ounces Filter Rating ........................................................................20 Micron Sump Capacity ..................................................................0.4 Ounce Port Threads ..........................................................................1/4 InchPressure & Temperature Ratings –Manual T wist Drain ............................0 to 300 PSIG (0 to 20.7 bar) 0°F to 180°F (-18°C to 82°C) Auto Pulse Drain ..................................10 to 175 PSIG (0 to 12 bar) 32°F to 150°F (0°C to 66°C)Note: Air must be dry enough to avoid ice formation attemperatures below 32°F (0°C)Weight........................................................................0.6 lb. (0.27 kg)Materials of ConstructionBody .....................................................................316 Stainless Steel Bowls ...................................................................316 Stainless Steel Deflector ..................................................................................Acetal Drain ....................................................................316 Stainless Steel Element Holder .......................................................................Acetal Filter Element ................................................................Polyethylene Seals .............................................................................FluorocarbonOperationFirst Stage Filtration:Air enters at inlet port and flows through deflector plate (A) which causes a swirling action. Liquids and coarse particles are forced to the bowl interior wall (B) by the centrifugalaction of the swirling air. They are then carried down the bowl wall by the force of gravity. The baffle (D) separates the lower portion of the bowl into a “quiet zone” (E) where the removed liquid and particles collect, unaffected by the swirling air, and are therefore not reentrained into the flowing air.Second Stage Filtration:After liquids and large particles are removed in the first stages of filtration, the air flows through element (C) where smaller particles are filtered out. The filtered air then passes downstream. Collected liquids and particles in the “quiet zone” (E) should be drained before their level reaches a height where they would be reentrained in the flowing air. This can be accomplished by unscrewing the drain valve (F) slightly until the liquid begins to drain.Technical InformationE F(Revised 11-21-12)。
亚德客过滤器工作原理
亚德客过滤器工作原理
亚德客过滤器是一种常见的网络过滤器，它的主要作用是对网络流量进行过滤和限制，以确保网络安全和资源利用的有效性。
该过滤器的工作原理可以简单概括为：根据事先设定的规则，对网络数据包进行检测和分析，然后根据规则的要求对数据包进行过滤或限制。
具体来说，亚德客过滤器可以通过以下方式实现过滤和限制： 1. 基于源IP地址或目的IP地址进行过滤，可以针对某些IP地址或 IP地址段进行限制或阻止访问。
2. 基于端口号进行过滤，可以限制某些端口的访问或阻止特定的协议流量。
3. 基于协议类型进行过滤，可以限制某些协议的访问或阻止某些协议的不安全流量。
4. 基于流量大小和带宽进行限制，可以防止某些用户占用过多的带宽，并保证网络资源的平衡利用。
在实际应用中，亚德客过滤器还可以通过多层过滤和集中管理等方式提高过滤的效率和精度，确保网络的安全和稳定。
同时，该过滤器也需要时刻更新规则库和升级版本，以适应不断变化的网络环境和威胁。
- 1 -。
Parker Zander 迷你过滤器系列：压缩空气、气体和疲劳过滤器说明书
Compressed air,gas and vacuum filtersCompressed air filters are now recognised as being an integral part of any system.Few,if any, compressed air systems can ope-rate successfully without high effi-ciency filters.Production and pro-cess standards demand the finest quality air and components are now manufactured to such tight tolerances that no contamination is permitted.We are one of the leaders in the purification of compressed air,gas and vacuum filters.Their product development is lead by strongpartnerships with compressed airand gas users to ensure the bestavailable product for increasinglydemanding applications.Dust,dirt and oil mist filtration iscommon enough today.ParkerZander emphasises,not only thefiltration efficiency but,important-ly,links this to energy costs interms of pressure differential,pro-duct consistency and reliability.Micro-filter-compressed air,gas and vacuum filtersBoth types of housings are built to the highest quality standards and have a double surface protection. The aluminium housings are alu-chromed and epoxy powder coated,the steel housings are intensivly cle-aned,polyester primed and acrylicpainted.Thanks to the attention of qualitysurface treatment,Parker Zanderoffers a10year guarantee on thefilter housings.This gives confiden-ce to the user!G-Housings with threaded connection from G1/4to G3 -High grade aluminium casting -Alu-chromed in and outside to prevent corrosion-Powder coated to ensure top quality finish F-Flanged housingsDN80to DN300-Welded mild steel vessels -Sand blasted,cleaned and de-greased-Polyester primed in and outside -Acrylic paint outsideMicro-filters in two housing formats:Filter HousingsUntreated and Alu-chromed filter bowlsafter a salt spray test acc.toDIN50021SS>250hoursAll Micro-filter housings are two piece.This means that,no matter what the size is,one person can change the filter ele-ments.This saves having to employ a helper!The F flanged filter housings,which can weigh up to a ton,have a hinged lower cover,which one person can open and close,when it is time to change the elements.Parker ZANDER Micro-filterMicro-filter Housing ConstructionOther types of housingMicro-filter Tie RodThe tie rod fixing of the element to the housing ensures that the ele-ment sits in the housing without any possibility of movement and therefore leakage between the dirty and clean side.The lower end cap of the element is firmly secured to the tie rod.This elimi-nates any possibility of the end cap flying off under severe shock conditions.Equally,the tie rod makes the ele-ment easier to change.There is no risk of the element end cap corro-ding.This does occur when alumini-um threads on the element corrode into the housing.This means anexpensive new housing instead of a simple ele-ment replacement.A small difference with large cost savings!Parker Zander element secured with tie rodAnother methodMicro-filter Modular ConceptThe user can install simply and economically Micro-filters inmodular units up to the ing a filter combination kit,the installer can link together up to three filters in a set.This lowers the conse-quential pressure drop.These filter combinationscan be easily wall mounted with brackets.Parker Zander filter housings combinati-onsOther types of housing linked with pipe or nip-ples3piece hous-ing with retain-ing ring2piece housingG FWDH KW G1/4-G3 DN80-DN300Standard combination (up to G13size only)Combination kits wall brackets G2StandardScrewedplugs Pressure diffe-rential gaugemanual drainFilter with G1/2thread connection,plug in(Standard on V–XP4)Filter with G1thread connection,oil removal"no-loss”condensate drain ED3000range.G2connection with activated carbon filter,Wall bracketsExamplesEOPK2K3Electronic filtermonitor DeltatronicOil indicatorElectronic level sensing drain Electronic level sensing drain Parker Zander filters use machine pleated elements,which form the heart of the filter.These pictures -higher dirt holding capacity -longer service life -lower operating costsTechnical DataC a p a c i t y *1n o m i n a lC o n n e c t i o nM a x .p r e s s u r eD i m e n s i o n sW e i g h tF i l t e r e l e m e n t*2calculated for constant velocity and 20°CExample 1:If you have a flow of 1300m 3/h (1bar a and 20˚C)–)at a minimum working pressure of 10bar e,what size filter do you require?Answer:Flow ÷f =1300m 3/h ÷1.38=940m 3/h =>G14size Example 2:What is the nominal flow through a G14filter with a minimum working pressure of 10bar e?Answer:Flow:·f =940m 3/h ·1.38=1300m 3/h (1bar a and 20˚C)Micro-filterParker Zander mm mm mm mm Anzahl/Type m 3/h G/DN bar A B C D kg TypeG 230G 1/4166016514600,61/1030G 350G 1/4168721521751,01/1050G 570G 3/8168721521901,01/1070G 7100G 1/21687285211601,21/1140G 9180G 3/416130325431353,81/2010G 11300G 116130425432354,51/2020G 12470G 11/216130525433355,01/2030G 13700G 11/216130725435256,41/2050G 14940G 216164825485209,61/3050G 171450G 21616410754877012,31/3075G 181940G 21/21625010507460024,61/5060G 192400G 31625012007475027,01/5075F 171850DN 8016380128017553052,01/3075F 192920DN 8016440132020553079,01/5075F 203700DN 100165001440230550106,02/3075F 305550DN 100165001440230550106,53/3075F 407400DN 150166401590280550148,04/3075F 6011100DN 150167901650300550208,06/3075F 8014800DN 200167901730340550230,08/3075F 10018500DN 200168401780360550368,010/3075F 12022200DN 250169401940420600450,012/3075F 16029600DN 250169401940420600460,016/3075F 20037000DN 300169401970450600520,020/3075*1Calculated at 1bar a and 20˚C at 7barg working pressureFilter Element Performance Tables Pre-filter element V–0.02bar (dry)–0.07bar (saturated)–99.99%(3µ)General Purpose Filter ZP –0.03bar (dry)–0.10bar (saturated)–99.9999%(1µ)–≤0.5mg/m 3(1bar a and 20˚C)Oil Removal Filter XP –0.06bar (dry)–0.15bar (saturated)–99.99999%(0.01µ)–≤0.01mg/m 3(1bar a and 20˚C)Super Fine Filter XP4–0.12bar (dry)–0.28bar (saturated)–≥99.99999%(0.01µ)–≤0.001mg/m 3(1bar a and 20˚C)Activated Carbon Filter A –0.03bar -≤0.003mg/m 3(1bar a and 20˚C)with an inlet concentration of ≤0.01mg/m 3Activated Carbon Cartridge KTA –Depending on size 0.15-0.4bar –bar (Oil Removal as A grade)Conversion factor f for other operating pressures*2Operating pressure bar e12345678910111213141516f=0.250.380.500.630.750.881.001.131.251.381.501.631.751.882.002.13DimensionsPre-filter,General purpose filter and Superfine filter V,ZP,ZX,XP4Standard format with automatic condensate drainGrades VD (E),ZPD(E),XPD(E)and XP4(E)Complete with automatic drain and differential pressure gauge (E with volt-free contact)Activated carbon filter A &KTAStandard format with manual drainActivated carbon filter AOP &KTAOPComplete with manual drain and oil indicatorDimensions with electronic condensate drainsLS rangeLC rangeG2-G13G14-G17/F17G18-F20F40-F120F160-F200G2-G13G14-G19/F19F20-F40F60-F200ED 3002ED 3004ED 3007ED 3030ED 3100ED2010ED2010ED2010ED2020MKMKMKMKMKMKMKMKMKM14-G38G12-G12G12-G12G10-G12G10-G12M14-G12G12-G12G10-G12G10-G34G10-G12Parker Hannifin CorporationZANDER Aufbereitungstechnik GmbH Im Teelbruch 118D-45219EssenTel:+49(0)20549341Fax:+49(0)2054934164www.zander.deYour local authorized Parker distributor。
亚德客气动元器件选型教材
C-ZPX□ H 大型真空吸盘
C-ZPX
X-KZFC型真空过滤器
水平真空接口
红色对应日系型号
什么是真空？
真空的吸附与气缸的作动原理一样 都是运用压力差来进行作动
真空发生 器 真空吸盘
真空系统的应用
真空发生装置
真空泵
真空发生器
结构负载，大流量工作，不 易频繁起停，适合集中使用
结构简单适用于流量不大的 间歇性工作
GR、SSR2R00200、BR
AR
2008 - 7
气动控制元件
3V 4M
B03
4V
2W
2S
4F
4H
ESV
4HV
ASC
XPPV
控制元件
按照阀芯的结构形式可分为：滑柱式、截止式。 台肩
功能特点：
易实现记忆功能 通用性 强
气体质量要求较高
频率高 流 量较小
单电控两位置先导式电磁换向阀
单电控先导式滑阀的特点是： ①、控制的主阀不具有记忆功能； ②、控制信号为长信号； ③、控制力大，控制信号必须克服复位弹簧力及P腔气体作用于阀芯上
4.气缸本体两面均有定位孔， 安装使用方便；
5.双气缸结构，可实 现双倍出力。
齿条采用SUS304精度 等级8级,表面氮化处理
本体采用铝挤型模具， 表面喷细砂后硬阳处理
前盖压铸成型,表面 喷砂-烤漆处理。
后盖压铸成型，表 面喷砂-烤漆处理。
齿轮采用20Cr冷挤压工艺，模数1.5， 精度等级8级，表面氮化处理。
执行 元件
空压机
F
`
v=1 ; p=1
v=0.5 ; p=2
p1 × V1 = p2 × V2
主管路处理装置
亚德客选型电子手册
标题：亚德客选型电子手册亚德客是全球知名专业生产各类气动器材的大型企业集团，致力于向客户提供满足其需求的气动控制元件、气动执行元件、气源处理元件、气动辅助元件等各类气动器材、服务和解决方案，为客户创造长期的价值和潜在的增长。
亚德客始创于1988年，现辖三大生产基地和一家营销中心，亚德客生产基地厂房面积达37万8千平方米，全球员工总计超过4500人，专业研发技术人员300多人，亚德客选型电子手册总投资1.5亿美元，年生产能力达5,000万件套，产品畅销中国、东南亚、欧美等国家和地区。
亚德客在中国大陆地区拥有近百家直销分公司/营业部，亚德客选型电子手册在全球更是有数千家经销商，主要位于欧洲、美洲及亚洲，形成了完善的销售网络和售后服务体系，可随时为客户提供便捷的服务。
亚德客以拓展集团生产和服务为未来发展的战略目标，坚持走人本优先、改革创新和集团化道路。
秉承“人本、共享、发展、责任”的企业核心价值观，亚德客始终如一地贯彻“以客为尊”的经营理念，始终如一地坚持“以技术创新为核心，亚德客选型电子手册以市场需求为导向”的经营方针，藉以不断完善“建立共好、责任承担、赏罚分明、学习成长”的集团文化，努力奋斗，自强不息，长久致力于全球工业自动化的持续发展。
台湾亚德客工业股份有限公司（简称台亚）成立于1988年11月，前身系健良股份有限公司，1990年更名为台亚。
早期的台亚主要生产电磁阀，此后亚德客选型电子手册陆续研发生产气缸、气源处理等产品。
目前，台亚产品以特殊规格气缸为主，拥有七大类十余系列数百个品种，年产量达到20万件套，主要供应台湾本地市场，满足客户需求及时效性。
1998年，台亚在同行中率先通过“ISO9000质量管理体系认证”；2004年，台亚取得“ISO14000环境体系认证”及“CE认证”。
长期以来，台亚秉持“质量第一、交货准时”的服务精神及理念满足客户需求，亚德客选型电子手册不断引进先进设备、生产工艺提升产品质量与品质。
亚德客电磁阀选型手册
亚德客电磁阀选型手册 Company Document number：WTUT-WT88Y-W8BBGB-BWYTT-19998
产品名称:电磁阀亚德客电磁阀选型手册
电磁阀（Electromagneticvalve）是用电磁控制的工业设备，是用来控制流体的自动化基础元件，属于执行器，并不限于液压、气动。
用在工业控制系统中调整介质的方向、流量、速度和其他的参数。
电磁阀可以配合不同的电路来实现预期的控制，而控制的精度和灵活性都能够保证。
电磁阀有很多种，不同的电磁阀在控制系统的不同位置发挥作用，最常用的是单向阀、安全阀、方向控制阀、速度调节阀等。
11451074DELCOS3000操作手册0175
CompAir DELCOS3000控制器DELCOS3000操作指南2目录8.1 操作元件 48.1.1 键盘 48.1.2 发光二极管 58.1.3 语言选择 68.1.4 空白文本区——第1行 68.1.5 空白文本区——第2行状态显示 68.2 DELCOS 3000菜单结构（示例）88.2.1 菜单[保养时间安排] 98.2.2 菜单[控制菜单] 98.2.3 菜单[故障存储器] 98.2.4 菜单[极限值] 108.2.5 菜单[可选输入项] 108.2.6 菜单[定时器控制]可选108.2.7 数值的修改128.2.8 密码的锁定和解锁定128.2.9 设置密码138.3 调试138.3.1 机器的起动138.3.2 加载和空载运行的操作148.3.3 关机148.3.4 失灵、跳闸和电源故障148.3.5 警告148.3.6保养148.3.7 汇集型故障继电器148.3.8运行/加载计时器148.3.9故障存储器158.4 发生故障或警告时DELCOS 3000故障表168.4.1 检查项目表168.4.2 故障/警告表168.5 保养时间间隔208.6 操作方式208.6.1 自动和连续运行208.6.2 远程控制（机器的开和关）208.6.3 远程控制（加载和卸载）（基本负载选择，从动）218.6.4 发生电源故障后的自动重新起动228.7 出厂前设定的极限值223图18.1 操作元件8.1.1 键盘I键=> 起动系统O键=> 关闭系统Θ键=> 确定键=> 在菜单中时：中断输入方式（恢复先前的数值）空白文本区=> 第1行：最终温度/最终压缩压力/总管压力的指示=> 第2行：状态显示（运行方式）菜单键MENU=> 打开和关闭菜单C键=> 输入存取代码（用于保护各种菜单项）↑键=> 在菜单中时：向上滚动在输入方式时：更改参数↓键=> 在菜单中时：向下滚动在输入方式时：更改参数←键=> 在菜单中左移一列→键=> 在菜单中右移一列键=> 输入值要被更改或确定48.1.2 发光二极管运行信息：LED a => 闪动：系统处在待命方式，即马达随时都会自动起动。