RSLogix5000如何更新EDS
RSLogix Emulate 5000 应用教程
RSLinx
RSLogix Emulate 5K
通过OPC方式与其他软件建立数据通道。
Logix5000 与Emulate 5000的连接
打开RSlogix5000，新建一个项目。如下
添加模块，选择模块时如下所示：
添加模块后，模块的参数照此修改。
打开RSLogix Emulate 5000，配置对应插槽的模块。
RSLogix Emulate 5000 应用
RSLogix Emulate 5000
Logix5000处理器模拟软件。用于： 1.在没有实际控制器的情况下进行 Logix5000编程的模拟和调试。 2.进行HMI应用的调试。
和其它Rockwell软件的关系
Logix 5000
RSview32
其它软件
n
n
新建立的 topic
n
打开RSview32,新建一个项目。
n
在节点中建立OPC服务器，指向RSLINX。
n
在标记数据库中建立HMI使用的TAG，指向处理器中 的标签。
n
定义完毕后就可以在画面中像正常在线开发一样使用 标签了。
点击按钮就 可以选择tag
总
n
结
RSLogix Emulate 5k可以用于DI\DO相关的流程控制 的仿真。 RSLogix Emulate 5k可以用于RSlogix5k和 RSview32开发过程中的仿真。 仿真时要使用TAG的别名，用别名指向RSLogix Emulate 5k处理器中的标签，完成后再修改为最终设 计的标签。
n
回到RSlogix5000就可 以看到er tags中 的地址列表了。
n
下一步就可以进行编程 工作了，方法和使用 Logix5000处理器相同。
RSLogix5000调试步骤-项目总结
1、安装RSLogix5000，订货是V19版本，光盘内集成有以前所有版本，安装时可以选择所有版本进行安装，授权通用2、Rslogix5000连接一个新PLC时，需要先给PLC刷新固件。
连接PLC 的步骤：将电脑的有线网络IP地址设置为自动获取，打开BOOTP/DHCP Server 设置子网掩码：255.255.255.0,会自动刷出PLC的MAC地址如下图。
双击MAC地址设置PLC的IP地址确认后点击Enable DHCP将地址下载PLC中，再点一下Disable Bootp/DHCP。
3、如果通过电脑直接连接PLC，IP地址要手动设置为：192.168.1.10，如果通过路由器则设置为自动获取。
首先组态RSlinx Classic通讯驱动。
Communications-Configure Drivers-Ethernet devices或EtherNet（此驱动只能连接PLC）/IPDriver(此驱动可以连接PLC和触摸屏)菲律宾项目用1769-L35E PLC与RSview 32上位机通过以太网通讯。
RSLinx Classic设置如下4. 设置Configure Client Applications点击RSWho,会自动识别连接到的PLCRslinx classic组态好后在RSlogix5000中点击找到cpu所在位置点击go online4、Compact-Logix 1769系列PLC，通过1769-SDN/B进行扩展机架时，相当于新加了一组子站，通过1769-SDN/B扫描新加子站，通讯方式为DeviceNet网通讯，如果距离近时可以通过终端盖板上的扩展电缆进行扩展。
1769-SDN/B 模块需要刷新固件后才正常通讯，将设置下载到1769-SDN/B模块中。
新加子站需加1769-ADN通讯模块，1769-SDN/B最多可加三个扩展即三个1769-ADN，SDN与AND连接线需要在ADN末端2,4端子（红，蓝）线加一个120欧姆的终端电阻。
RSLogix5000系统伺服轴属性说明(收藏)
RSLogix5000系统伺服轴属性说明1. General (2)2. Motion Planner (4)3. Unit (6)4. Drive/Motor (8)5. Motor Feedback (13)6. Aux Feedback (14)7. Conversion (15)8. Homing (17)9. Hookup (20)10. Tune (22)11. Dynamics (23)12. Gains (25)13. Output (30)14. Limits (32)15. Offset (35)16. Fault Action (36)17. Tag (40)1.GeneralUse this tab to do the following for an axis, of the data type AXIS_SERVO_DRIVE.§Configure the axis for Servo operation or for position Feedback Only.选择此轴是伺服操作还是仅用作反馈。
§Assign the axis, or terminate the assignment of an axis, to a Motion Group.将轴与运动组关联起来。
我们建的轴组名称为MG。
§Associate the axis with a 1756-M08SE motion module.§View the base node of the associated 1756- M08SE motion module.Note that RSLogix 5000 supports only one Motion Group tag per controller.When a parameter transitions to a read-only state, any pending changes to parameter values are lost, and the parameter reverts to the most recently saved parameter value.When multiple workstations connect to the same controller using RSLogix 5000 and invoke the Axis Wizard or Axis Properties dialog, the firmware allows only the first workstation to make any changes to axis attributes. The second workstation switches to a Read Only mode, indicated in the title bar, so that you may view the changes from that workstation, but not edit them.请注意，RSLogix 5000仅支持一个控制器对应一个运动组标签。
RSLogix5000 软件应用
HuaZhang Electric Custom Training
组态模块在编程模式和故障模式下以及在通讯失败后的输出状态。 选择 Next
该窗口用于在上线时复位电子熔断和诊断锁存。 选择 Next
Lab2- 6 -
Lab material for RSLogix5000
HuaZhang Electric Custom Training
4) 树形目录项目管理器
控制器文件夹
任务文件夹
2．控制器属性设置
数据类型文件夹 I/O 组态文件夹
Lab2- 2 -
Lab material for RSLogix5000
HuaZhang Electric Custom Training
5) 查看控制器属性，更改控制器类型。 右键点击控制器文件夹，然后选择属性（Properties）。在 General 表中
更改控制器
3．I/O 配置 6) 组态本地数字量 I/O 模块。
右键点击 I/O configuration 文件夹，然后选择 New Module。在模块类型 列表中选择 1756-OB16D（数字量直流输出模块），单击 OK；确定版本信息 后在跳出的对话框中设置模块属性，输入模块的名称、描述（可选），选择槽 号、通讯格式、电子锁方式等；点击 Next 逐步设置 RPI 时间等内容。所有组 态完成后，点击 Finish。
点击 OK
Lab2- 8 -
Lab material for RSLogix5000
HuaZhang Electric Custom Training
选择 Next
设置 RPI 时间，该时间决定了模拟量输入模块何时广播它的通道数据和状态数 据。 选择 Next
RSLogix5000项目操作指南说明书
OverviewThis document is a procedure on how to import an Add-On Instruction and use it in the Main Routine of an RSLogix5000 project.Before you StartBefore importing the Add-On Instruction follow these steps▪Download EDS files for C445 at /C445▪Add the C445 to the Ethernet/IP network in RSLogix5000 using the EDS files▪Generic Ethernet Device may also be used to add the C445 to an Ethernet/IP networkScale FactorsC445 has different Scale Factor assignments for Current and Power depending on the current range:The C445 Add-On Instructions provide current and power (kW) in floating point format. These programs take care of the scaling, so there are 3 Add-On Instructions for any selected I/O pair. C445 AOIs are available for I/O pairs 116/3 and 106/110.InstructionsTo use one of the C441 Add-On Instructions for I/O assemblies 116/3, follow these steps. The same steps apply for other I/O assemblies like 106/110.▪Open the RSLogix5000 project where it will be used▪Create an Ethernet/IP network and add the C445▪Select the 116/3 I/O assembly pair▪Right click on Add-On Instructions on the tree on the left of the screen and select Import Add-On Instruction▪Locate the Add-On Instruction on your computer and select Open. The tree in RSLogix5000 should look like the following:▪The parameters, tags and logic for this Add-On Instruction are available to view under C445_AOI_116_3_SmallFrameSize (Small frame size used in this example)▪To add this Add-On Instruction to the Main Routine, open the MainRoutine as shown below:▪In the area above where logic is entered are all of the available instructions. Select the category called “Add-On” and the C445 Add-On Instruction will be displayed above it, as shown below:▪Select the C445 AOI to add it to your program as shown below:▪Double click the “?” to the left of the ellipses and enter a name for this AOI block. For this exam-ple, C445 is used. Right click on C445 and choose New “C445” - the following window will open:▪Be sure all fields have the selections shown above, then select “Cr e ate”▪Add the Input and Output addresses by selecting the “?” next to each one and select the ad-dresses as shown below▪Note: Under the Input tag category is C445:I1.ConnectionFaulted. This is a BOOL tag that is a 1 if the connection is lost to the C445 and a 0 if the connection is good. Monitor this bit for connec-tion status for the C445 by assign ing it to the “Comm_Status” tag shown below the I/O tagsComplete!The information for the Add-On Instruction will now be displayed and the instruction is now included in your logic. Specific tags were selected to be displayed in the instruction, but all I/O tags are now availa-ble to be used in the programTags correspond to the tag names documented in the C445 user manual (publication MN0420003EN) Appendix C for Input assembly 116 and Output assembly 3. They are located in the Parameters and Lo-cal Tags area under “MainProgram” in the RSLogix5000 project. All Input and Output tags are shown below for 116/3. Refer to user manual for tags used with 106/110.The Logic area for the Add-On Instruction associates the generic I/O tags RSLogix5000 creates with the descriptive tags shown above. These generic I/O tags are created when a device is added to the Ethernet network. The generic I/O tags can be found in the Controller Tags area.The descriptive tags shown above may now be used to control and monitor the C445.Supporting DocumentationC445 User Manual MN0420003EN/C445Additional HelpIn the event that additional help is needed, contact the Technical Resource Center at1-877-ETN-CARE Option 2, Sub Option 2。
RSLogix5000操作简明教程
RS Logix5000操作简明教程1．IO配置1.1打开RS Logix500，创建新工程项目，菜单栏File->New1.2在New Controller对话框中选择CPU类型（Type）、给CPU命名（Name）、选择机架槽数类型（Chsssis Type）、CPU安装在机架上的槽号（Slot）一般默认为0槽、工程命名及保存位置（Create In）1.3单击“OK”，工程框架建立，主要部分Controller Tags添加所需Tag、MainProgram下编写梯形图、IO Configuration设置建立系统各模块连接结构，IOConfiguration是首先要完成的工作。
IOConfiguration第一步：首先设置主机架上的模块，即在背板机架Backplane上右键->New Module添加新模块第二步：在Select Module对话框中By Vendor选项卡选择所需模块型号，单击“OK”完成模块选择，这里选择了一个ControlNet通讯模块第三步：在Select Major Revision对话框中选择模块版本，一般默认版本即可，“OK”第四步：在New Module对话框中，设置模块名称（Name）、在机架上的槽号（Slot），对于ControlNet模块要设置节点号（Node），在一个ControlNet网络中节点号唯一,ControlNet模块上节点设置机械拨码与此处设置节点号必须一致！以太网模块需设置IP地址，此乃后话。
添加ControlNet通讯模块在Controller Tags对话框中是没有TAG的，若添加的是输入输出模块则会自动生成TAG如添加一输出模块，在背板机架Backplane上右键->New Module添加新模块->选择1756-OA16->“OK”->输入模块名->”OK”->”OK”,此时在Controller Tags对话框中就会出现系统生成的该模块Tag，有Local:2:I、Local:2:O、Local:2:C，因其为输出模块故将Local:2:O 展开，Local:2:O.Data.x即对应模块上的输出点；，在Description栏中为各数据位填写说明即完成IO配置系统生成模块Tag命名说明模块名：槽号：标识（输入或输出等）.数据类别.数据位Local:2:O.Data.0若要建立ControlNet网络（远程IO），则在最初添加的ControlNet通讯模块下的ControlNet 图标右键添加New Module，选择ControlNet模块添加并设置好名称、节点号、机架槽数、安装槽号等再在新添加的ControNet模块下的Backplane下添加新的模块，如一个输入模块1756-IB32/B 这样就建立起了一个最简单的ControlNet网络，包括主站（CPU模块+ControlNet通讯模块+输出模块）、从站（ControlNet通讯模块+输入模块）在ControllerTags中给每一个输入输出点填写好说明信息Description即完成IO配置！下一步就可以进行程序的编写了。
RSLogix5000用户手册
AB_RSLogix5000初级使用手册目录：设定笔记本IP地址 (3)查看PLC硬件组态信息 (3)设定RSLinx (4)打开RSLogix5000软件创建与RSLinx相符的程序 (7)在RSLogix5000软件中创建程序章节、程序段落、程序自然段 (10)上传和下载程序 (13)创建行参 (16)RSLinx查看网络IP以及硬件 (18)PLC静态和动态IP地址分配 (21)Firmware刷新 (25)Rxlogx5000软件的在线修改功能 (28)Rxlogx5000软件的在线强制功能 (31)范围指令LIM需要注意的是，当Low Limit < High Limit数值时，LIM命令在Low Limit和High Limit之间的数值时输出。
如果Low Limit > High Limit数值时，LIM命令在Low Limit和High Limit之间的数值时停止输出。
(35)查找跳转、中断等子程序块的位置 (35)RSLogix5000软件的在线帮组功能 (36)Routine里程序的类型 (37)一个Project里可以最多建立32个Task，但只能有一个Task属性为Continuous （连续扫描）其余的31个Task可以分配给Event（事件扫描）或者Periodic（中断扫描）。
每一个Task里可以建100个Program，每一个Program可以建立无穷个routine。
(38)备份程序和解压程序 (41)程序的比较 (43)Flash Memory Card 程序备份和下载操作 (46)模拟量模块的组态、量程设定、模拟量输出的钳位设定。
(49)Device Net网络配置 (53)Device Net软件安装 (55)Device Net组网 (57)在RSLogix5000程序里添加DeviceNet硬件 (69)DeviceNet的硬件寻址 (71)配置EtherNet以太网远程I/O (75)实时监控趋势图 (81)EDS文件更新 (85)设定笔记本IP地址1．查看AB_PLC机器槽架上的CPU模块显示的IP地址，一般PLC的IP地址为为10.0.0.1，笔记本上的IP最后一位设置需要变化。
RSLogix5000使用
图4-1 New Task对话框
任务的三种类型
• 连续型任务 指的是周而复始连续执行的任务，一个项目
只允许定义1个，亦可以不定义。
•
周期型任务 指的是定时中断执行的逻辑程序，周期性的执 行任务，须定义周期时间，要设定优先级别，最多可以定义31
个。
•
事件触发型任务 指的是事件触发引起的任务调用，事件触 发可以是外部输入点变化引起（如同PLC5/SLC500）,也可以由 Consumed 标签引起或直接指令调用引起，还可以由运动控制状 态引起，要设定优先级别，最多可以定义31个。
图1-1 RSLogix 5000主界面
2．创建一个新的控制器文件 ① 从File菜单选择New，显示New Controller对话框。 ② 从Type的下拉菜单中选择1769-L32E CompactLogix 5332E Controller。 ③ 在Revision的下拉菜单中选择15。 ④ 在Name栏中键入字母和数字组合作为处理器的名字， 如Test1。 ⑤ 在Create In栏内键入文件保存路径或点击Browse键定 位地址目录，我们创建文件目录在C：\RSLogix 5000\Projects\ 。 ⑥ 确认输入与图2-1所示吻合，然后点击OK。由此创建 了一个控制器文件。其界面如图2-2所示；
•
•
•
文本编程ST 采取ASCII代码编写程序，通常用于复杂或特殊 要求的运算，这些可能用梯形图的运算指令难以完成。
功能块FBD 组态过程控制，是引入的DCS系统的仪表控制组态 方式，由功能块之间的连接建立程序结构。
19
图6-2 Program Properties界面
图6-3 编程界面
7．远程I/O模块 1. 从Controller Organizer右击1769-L32E Ethernet Port LocalENB 图标，选择New Module。 2. 在Type栏中附有可选Communications系列模块的列表，选择 1794-AENT/A。按图7-1配置。 输入参数说明： Address/Host Name –为要控制的远程IO IP地址，地址在机架下 标注。 Disable Keying – 电子锁不起作用。 3. 从Controller Organizer右击1794-AENT/A Aent图标，选择New Module。显示Select Module Type对话框，如图7-2所示，附有可 选模块的清单，可以首先在对话框下部选择模块类型比如 Digital表示数字量模块，然后在下拉列表中找到所需的模块型 号即可，例如16点数字量输入模块1794-IB16/A，双击所选择的 模块。显示模块属性对话框，如图7-3所示，输入正确的参数， 再点击Finish。RSLogix5000软件将完成模块的组态。
罗克韦尔自动化 Logix 5000 控制系统参考手册说明书
Reference ManualOriginal InstructionsIntegrated ArchitectureLogix Control Systems Recommended Literature Controllers: Bulletin 1756, 1769, 5069Drives: Bulletin 20G, 20J, 2198I/O and Communication Modules: Bulletin 1715, 1756, 5069, 5094Graphic Terminals: Bulletin 2711P, 2713P, 2715PSoftware: Bulletin 9324Links to some of the most common manuals for products that are typically included in a Logix 5000™ control system. It also provides links to manuals that can help you:•Implement an EtherNet/IP network.•Develop a Logix controller-based safety system.•Use Studio 5000 Logix Designer® application to program your control system.•Use Studio 5000 View Designer® application to configure and program your operator interface.•Configure a motion solution.•Configure and use Rockwell Automation products to improve the security of your automation system. Topic PageSummary of Changes2Products Covered in this Publication2Logix 5000 Controllers Resources3Network and Communication Modules Resources4Instructions and Programming Resources4Security Resources5I/O Modules and Adapters Resources6Operator Interface Resources6Motion Resources7Drives Resources7Additional Resources92Rockwell Automation Publication IASIMP-RM001J-EN-P - September 2021Logix Control Systems Recommended Literature Reference ManualSummary of ChangesThis publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.Products Covered in this PublicationYou can find common manuals for these products in this publication.Controllers•1756 Series ControlLogix® Controllers, GuardLogix® Controllers, ControlLogix Redundancy Modules •5069 Series CompactLogix™ Controllers, Compact GuardLogix Controllers •1769 Series CompactLogix Controllers, Compact GuardLogix ControllersDrives•Kinetix® 5100, 5300, 5500, and 5700 Servo Drives •PowerFlex® 755T Drives with TotalFORCE® technologyStudio 5000 Design Environment•Studio 5000 Logix Designer® application •Studio 5000 View Designer® application •Studio 5000® Application Code ManagerI/O and Communication Modules•1756 ControlLogix I/O Modules and EtherNet/IP Communication Modules •Compact 5000™ I/O Modules and EtherNet/IP Communication Modules •FLEX 5000™ I/O Modules and EtherNet/IP Communication Modules •1715 Redundant I/O Modules •EtherNet/IP AdaptersOperator Interface•PanelView™ 5510 and PanelView 5310 Terminals•PanelView™ Plus 7 Standard and Performance TerminalsTopicPage Added ControlLogix 5580 Redundant Controllers User Manual to Logix 5000 Controllers resources 3Added Logix Designer Compare Tool User Manual to Programming resources 5Added CIP Security Proxy User Manual to Security resources5Added Studio 5000 View Designer software manuals to Operator Interface resources 6Added Kinetix 5300 Single-axis EtherNet/IP Servo Drives manuals to Drives resources7Added PowerFlex Drives with TotalFORCE Control Programming Manual - Firmware Revision 10 or later to Drives resources 7Added replacement guides to Drives resources7Logix Control Systems Recommended Literature Reference ManualOther Integrated Architecture System ProductsFor products not covered in this manual, go to the Technical Documentation Center at rok.auto/techdocs to browse documentation collections organized by product family. Or go to Literature Library at rok.auto/literature to search for documentation by catalog number, product name, or publication number.Logix 5000 Controllers ResourcesReference and task-based information to help you install, configure, and operate Logix controllers.Selection and Specifications•1756-SG001, ControlLogix System Selection Guide•1756-TD001, ControlLogix and GuardLogix Controllers Technical Data Specifications•1769-SG001, CompactLogix System Selection Guide•5069-TD002, CompactLogix and Compact GuardLogix Technical Data SpecificationsDesign Considerations•1756-RM094, Logix 5000™ Controllers Design Considerations Reference Manual•LOGIX-RM002, Estimated Logix 5000 Controller Instruction Execution Times Reference ManualManuals•ControlLogix and GuardLogix controllers user manuals-1756-UM543, ControlLogix® 5580 and GuardLogix 5580 Controllers User Manual-1756-UM015, ControlLogix 5580 Redundant Controllers User Manual-1756-UM022, GuardLogix 5570 Controllers User Manual-1756-UM001, ControlLogix System User Manual (for ControlLogix® 5570 and ControlLogix® 5560 controllers)-1756-UM535, ControlLogix 5570/5560 Redundancy User Manual•CompactLogix and Compact GuardLogix controllers user manuals-5069-UM002, CompactLogix 5480 User Manual-5069-UM001, CompactLogix 5380 and Compact GuardLogix 5380 Controllers User Manual-1769-UM021, CompactLogix 5370 Controllers User Manual-1769-UM022, Compact GuardLogix 5370 Controllers User Manual•Safety system reference manuals for GuardLogix and Compact GuardLogix controllers-1756-RM012, GuardLogix 5580 and Compact GuardLogix 5380 Controller Systems Safety Reference Manual-1756-RM099, GuardLogix 5570 and Compact GuardLogix 5370 Controller Systems Safety Reference Manual-1756-RM093, GuardLogix Controller Systems Safety Reference Manual (for GuardLogix 5570, GuardLogix 5560, and 1768 CompactGuardLogix Safety controllers using RSLogix 5000® version 20 and earlier)Rockwell Automation Publication IASIMP-RM001J-EN-P - September 20213Logix Control Systems Recommended Literature Reference ManualReplacement Guidelines•1756-RM100, Replacement Guidelines: Logix 5000 Controllers Reference ManualGuidelines for replacing the following:-ControlLogix 5560 or ControlLogix 5570 controller with a ControlLogix 5580 controller-GuardLogix 5560 or GuardLogix 5570 controller with a GuardLogix 5580 controller-CompactLogix5370L3controller to CompactLogix 5380 controllerNetwork and Communication Modules ResourcesReference and task-based information to help you design and implement an Ethernet network, and use EtherNet/IP communication modules in a Logix 5000 control system.Selection and Specifications•1756-TD003, 1756 ControlLogix Communication Modules SpecificationsDesign and Application Considerations•ENET-RM002, Ethernet Design Considerations Reference Manual•ENET-AT001, EtherNet/IP QuickConnect Application Technique•ENET-AT002, EtherNet/IP Socket Interface Application Technique•ENET-AT006, EtherNet/IP Parallel Redundancy Protocol Application Technique•ENET-AT007, EtherNet/IP Device Level Ring Application TechniqueManuals•ENET-UM006, EtherNet/IP Network Configuration User Manual-Overview of EtherNet/IP communication modules in Logix 5000 control systems; describes features and tasks that are common toEtherNet/IP network devices•ENET-UM004, ControlLogix EtherNet/IP Network Devices User Manual-Describes features and tasks that are specific to 1756 ControlLogix EtherNet/IP communication modules in Logix 5000 control systems •CNET-RM001, ControlNet to EtherNet/IP Migration Reference Manual-Provides information to migrate from an existing ControlNet® network to an EtherNet/IP™ networkInstructions and Programming ResourcesInformation to help you use Studio 5000 Logix Designer application to program your control system.Logix 5000 Controllers Instructions•1756-RM003, General Instructions Reference Manual•MOTION-RM002, Motion Instructions Reference Manual•1756-RM006, Advanced Process Control and Drives Instructions Reference Manual•1756-RM095, GuardLogix Safety Application Instruction Set Reference Manual•1756-RM087, Execution Time and Memory Use Reference Manual4Rockwell Automation Publication IASIMP-RM001J-EN-P - September 2021Logix Control Systems Recommended Literature Reference Manual Logix 5000 Controllers Common ProceduresThese manuals describe common procedures for programming and operating Logix 5000 controllers: 1756 ControlLogix, 1756 GuardLogix, 1769 CompactLogix, 1769 Compact GuardLogix, 5069 CompactLogix, and Studio 5000 Logix Emulate™.1756-PM001, Logix 5000 Controllers Common Procedures Programming Manual (provides links to the manuals in the following list)•1756-PM010, Add-On Instructions Programming Manual•1756-PM013, ASCII Strings Programming Manual•1756-PM020, Data Access Programming Manual•1756-PM002, EDS AOP Guidelines for Studio 5000 Logix Designer Programming Manual•1756-PM009, Function Block Diagram Programming Manual•1756-PM018, IEC 61131-3 Compliance Programming Manual•1756-PM019, Import/Export Project Components Programming Manual•1756-PM015, Information and Status Programming Manual•1756-PM004, I/O and Tag Data Programming Manual•1756-PM008, Ladder Diagram Programming Manual•1756-PM014, Major, Minor, and I/O Faults Programming Manual•1756-PM012, Messages Programming Manual•1756-PM017, Nonvolatile Memory Card Programming Manual•1756-PM011, Produced and Consumed Tags Programming Manual•1756-PM021, Program Parameters Programming Manual•1756-PM016, Security Programming Manual•1756-PM006, Sequential Function Charts Programming Manual•1756-PM007, Structured Text Programming Manual•1756-PM005, Tasks, Programs, and Routines Programming ManualProgramming Manuals•LOGIX-UM003, Studio 5000 Application Code Manager User Manual•LOGIX-UM006, Logix Designer and Library Object Manager User Manual•LDCT-UM001, Logix Designer Compare Tool User Manual•LOGIX-UM001, PhaseManager™ Software User Manual•1756-RM084, Import/Export Reference Manual•1756-RM085, Converting PLC-5® or SLC™ 500 Logic to Logix5550® Logic Reference ManualSecurity ResourcesResources to help you configure and use Rockwell Automation products to improve the security of your automation system.•SECURE-UM001, Security Configuration User Manual•SECURE-RM001, System Security Design Guidelines•SECURE-AT001, CIP Security™ with Rockwell Automation Products Application Technique•1783-UM013, CIP Security Proxy User ManualRockwell Automation Publication IASIMP-RM001J-EN-P - September 20215Logix Control Systems Recommended Literature Reference ManualI/O Modules and Adapters ResourcesReference and task-based information to help you install, configure, and operate I/O modules in a Logix 5000 control system. The products in this section are compatible with our newest controller platforms. To find manuals for other distributed I/O families, visit our Technical Documentation Center at rok.auto/techdocs.Selection and Specifications•1756-TD002, ControlLogix I/O Modules Technical Data Specifications•1715-TD001, 1715 Redundant I/O System Technical Data Specifications•5069-TD001, Compact 5000 I/O Modules and EtherNet/IP Adapters Technical Data Specifications•5094-TD001, FLEX 5000 I/O Modules Technical Data SpecificationsManuals•1756 ControlLogix I/O Modules-1756-UM058, ControlLogix Digital I/O Modules User Manual-1756-UM009, ControlLogix Analog I/O Modules User Manual•1715 Redundant I/O System-1715-UM001, 1715 Redundant I/O System User Manual•Compact5000I/O Modules-5069-UM007, Compact 5000 EtherNet/IP Adapters User Manual-5069-UM004, Compact 5000 Digital I/O Modules User Manual (includes standard and safety I/O)-5069-UM005, Compact 5000 Analog I/O Modules User Manual-5069-UM006, Compact 5000 Series High-speed Counter Modules User Manual-5069-UM003, Compact 5000 I/O Serial Module User Manual•FLEX 5000 I/O Modules-5094-UM005, FLEX 5000 EtherNet/IP Adapters User Manual-5094-UM001, FLEX 5000 Standard and Safety Digital I/O Modules User Manual-5094-UM002, FLEX 5000 Analog I/O Modules User Manual-5094-UM003, FLEX 5000 High-speed Counter Module User Manual-5094-UM007, FLEX 5000 Analog Isolated Current/Voltage/HART Input and Output ModulesOperator Interface ResourcesReference and task-based information to help you install, configure, and operate graphic terminals in a Logix 5000 control system. To find manuals for other PanelView products, visit our Technical Documentation Center at rok.auto/techdocs.Selection and Specifications•VIEW-SG001, Visualization Solutions Selection Guide•2715P-TD001, PanelView 5510 Terminals Technical Data Specifications•2713P-TD001, PanelView 5310 Terminals Technical Data Specifications•2711P-TD008, Bulletin 2711P PanelView Plus 7 Standard Terminals Technical Data Specifications•2711P-TD009, Bulletin 2711P PanelView Plus 7 Performance Terminals Technical Data Specifications6Rockwell Automation Publication IASIMP-RM001J-EN-P - September 2021Logix Control Systems Recommended Literature Reference ManualManuals•9343-GR001, Studio 5000 View Designer Getting Results Guide•9324-UM001, Studio 5000 View Designer User Manual•2715P-UM001, PanelView 5510 Terminals User Manual•2713P-UM001, PanelView 5310 Terminals User Manual•2711P-UM007, Bulletin 2711P PanelView Plus 7 Standard Terminals User Manual•2711P-UM008, Bulletin 2711P PanelView Plus 7 Performance Terminals User ManualMotion ResourcesReference and task-based information to help you configure and startup a motion solution.•MOTION-UM003, Integrated Motion on the EtherNet/IP Network Configuration and Startup User Manual•MOTION-RM003, Integrated Motion on the EtherNet/IP Network Reference Manual (AXIS_CIP_DRIVE attributes and integrated motion on the EtherNet/IP network control modes and methods)•MOTION-UM002, Motion Coordinate System User Manual•MOTION-AT005, Motion System Tuning Application Technique (tuning a Kinetix drive system)•IA-AT003, Integrated Architecture and CIP Sync™ Configuration Application Technique•MOTION-UM001, SERCOS and Analog Motion Configuration and Startup User ManualDrives ResourcesReference and task-based information to help you install, configure, and operate Allen-Bradley® Drives in a Logix 5000 control system. To find manuals for other Kinetix Servo Drive or PowerFlex Drive products, visit our Technical Documentation Center at rok.auto/techdocs.Selection and Specification•Kinetix EtherNet/IP Servo Drives-KNX-SG001, Kinetix Motion Control Selection Guide-KNX-TD003, Kinetix Servo Drives Specifications Technical Data-KNX-TD004, Kinetix Motion Accessories Specifications Technical Data•PowerFlex 755T AC Drives-PFLEX-SGOO2, PowerFlex Low Voltage Drive Selection Guide-750-TD100, PowerFlex 750-series Products with TotalFORCE Control Technical DataRockwell Automation Publication IASIMP-RM001J-EN-P - September 20217Logix Control Systems Recommended Literature Reference ManualManuals•Kinetix 5100 Single-axis EtherNet/IP Servo Drives-KNX-RM011, Kinetix 5100 Drive Systems Design Guide-2198-UM004, Kinetix 5100 Single-axis EtherNet/IP Servo Drives User Manual•Kinetix 5300 Single-axis EtherNet/IP Servo Drives-KNX-RM012, Kinetix 5300 Drive Systems Design Guide-2198-UM005, Kinetix 5300 Single-axis EtherNet/IP Servo Drives User Manual•Kinetix 5500 EtherNet/IP Servo Drives-KNX-RM009, Kinetix 5500 Drive System Design Guide-2198-UM001, Kinetix 5500 Servo Drives User Manual•Kinetix 5700 EtherNet/IP Servo Drives-KNX-RM010, Kinetix 5700 Drive Systems Design Guide-2198-UM002, Kinetix 5700 Servo Drives User Manual-2198-RM001, Kinetix 5700 Safe Monitor Functions Safety Reference Manual•PowerFlex 755T AC Drives-750-UM004, PowerFlex 755/755T Integrated Safety - Safe Torque Off Option Module User Manual-750-UM005, PowerFlex 755/755T Integrated Safety Functions Option Module User Manual-750-PM101, PowerFlex Drives with TotalFORCE Control Programming Manual - Firmware Revision 10 or later-750-PM100, PowerFlex Drives with TotalFORCE Control Programming Manual - Firmware Revision 6 or earlier-750-RM100, PowerFlex 750-Series Products with TotalFORCE Control Reference ManualReplacement Guidelines•Kinetix 5100 EtherNet/IP Servo Drives-2198-RM004, Kinetix 300 to Kinetix 5100 Servo Drives-2198-RM003, Ultra3000 to Kinetix 5100 Servo Drives•Kinetix 5300 EtherNet/IP Servo Drives-2198-RM005, Kinetix 350 to Kinetix 5300 Servo Drives-2198-RM006, Ultra3000 Digital Servo Drives to Kinetix 5300 Servo Drives•Kinetix 5500 EtherNet/IP Servo Drives-2093-AP001, Kinetix 2000 Multi-axis Servo Drives to Kinetix 5500 Servo Drives-2098-AP002, Ultra3000 Digital Servo Drives to Kinetix 5500 Servo Drives•Kinetix 5700 EtherNet/IP Servo Drives-2198-RM002, Kinetix 6000 Servo Drives to Kinetix 5700 Servo Drives•PowerFlex 755T AC Drives-750-RM003, PowerFlex 700AFE to PowerFlex 755TM Regenerative Bus Supply-750-RM004, PowerFlex 700S Phase II Drives to PowerFlex 755TL/TR Drives and PowerFlex 755TM Common Bus Inverters 8Rockwell Automation Publication IASIMP-RM001J-EN-P - September 2021Rockwell Automation Publication IASIMP-RM001J-EN-P - September 20219Logix Control Systems Recommended Literature Reference ManualAdditional ResourcesThese resources also provide helpful information for Logix 5000 control systems.You can view or download publications at rok.auto/literatureResourceDescriptionProduct Selection and Configuration website, rok.auto/systemtoolsProvides tools for product selection, control systems configuration, safety systems configuration, and power and motion systems.Sample Code Library, /global/sample-code/overview.page Share or download logic, HMI, and drives code.Industrial Components Preventive Maintenance, Enclosures, and Contact Ratings Specifications, publication IC-TD002Provides a quick reference tool for Allen-Bradley industrial automation controls and assemblies.Safety Guidelines for the Application, Installation, and Maintenance of Solid-State Control, publication SGI-1.1Designed to harmonize with NEMA Standards Publication No. ICS 1.1-1987 and provides general guidelines for the application, installation, and maintenance of solid-state control in the form of individual devices or packaged assemblies incorporating solid-state components.Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1Provides general guidelines for installing a Rockwell Automation industrial system.Product Certifications website, rok.auto/certifications .Provides declarations of conformity, certificates, and other certification details.Publication IASIMP-RM001J-EN-P - September 2021Supersedes Publication IASIMP-RM001I-EN-P - May 2020Copyright © 2021 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.Rockwell Automation SupportUse these resources to access support information.Documentation FeedbackYour comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback .Technical Support Center Find help with how-to videos, FAQs, chat, user forums, and product notification updates.rok.auto/support KnowledgebaseAccess Knowledgebase articles.rok.auto/knowledgebase Local Technical Support Phone Numbers Locate the telephone number for your country.rok.auto/phonesupport Technical Documentation Center Access technical documentation organized by product family.rok.auto/techdocs Literature LibrarySearch for installation instructions, manuals, brochures, and technical data publications.rok.auto/literature Product Compatibility and Download Center (PCDC)Get help determining how products interact, check features and capabilities, and find associated firmware.rok.auto/pcdcRockwell Automation maintains current product environmental certification information on its website at rok.auto/pec .Allen-Bradley, Compact 5000, CompactLogix, ControlLogix, expanding human possibility, FactoryTalk, FLEX 5000, GuardLogix, Integrated Architecture, Kinetix, Logix 5000, PanelView, PhaseManager, PLC-5, PowerFlex, Rockwell Automation, Rockwell Software, RSLogix 5000, SequenceManager, SLC, Studio 5000 Logix Designer, Studio 5000 Logix Emulate, Studio 5000 View Designer, and TotalFORCE are trademarks of Rockwell Automation, Inc.CIP Security, CIP Sync, ControlNet, DeviceNet, and EtherNet/IP are trademarks of ODVA, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752, İçerenkÖy, İstanbul, Tel: +90 (216) 5698400 EEE YÖnetmeli ğine Uygundur。
RSLogic5000安装和使用手册
Publication 9399-RLD300GR 技術支援電話：1-440-646-780技術支援傳真：1-440-646-7801 世界網站 ：1999，2000 Rockwell 軟體公司，Rockwell 自動化公司，在美國版權所有，翻印必究。
部份版權由Allen-Brandley 公司‧ LLC ，Rockwell 自動化公司所有。
此手冊和相關Rockwell 軟體屬於Rockwell 軟體公司所有。
若非經Rockwell 軟體公司同意，嚴禁翻印。
請遵照執照合約細則。
Rockwell 軟體公司商標, RSAlarm, RSAnimator, RSAssistant, RSBatch, RSBreakerBox,RSButton, RSChart, RSCompare, RSControlRoom, RSData, RSDataPlayer, RSEventMaster,RSGuage, RSJunctionBox, RSLogix Emulate 5, RSLogix Emulate 500, RSGuardian,RSHarmony, RSKeys, RSLadder, RSLadder 5, RSLadder 500, RSLibrary Builder, RSLinx,RSLogix 5, RSLogix 500, RSLogix Frameworks, RSLogix SL5, RSMailman, RSNetworx forControlNet, RSNetworx for DeviceNet, RSPortal, RSPower, RSPowerCFG , RSPowerRUN,RSPowerTools, RSRules, RSServer32, RSServer, RSServer OPC Toolkit, RSSidewinderX,RSSlider, RSSnapshot, RSSql, RSToolbox, RSToolPak I, RSToolPak II, RSTools, RSTrainer,RSTrend, RSTune, RSVessel, RSView32, RSView, RSVisualLogix, RSWheel, RSWire,RSWorkbench, RSWorkshop, SoftLogix 5, A.I. Series, Advanced Interface (A.I.) Series,AdvanceDDE, AutomationPak, ControlGuardian, ControlPak, ControlView, INTERCHANGE,Library Manager, Logic Wizard, Packed DDE, ProcessPak, View Wizard, WINtelligent,WINtelligent LINX, WINtelligent LOGIC 5, WINtelligent VIEW, WINtelligent RECIPE,WINtelligent VISION, and WINtelligent VISION2 是Rockwell 軟體公司/自動化公司註冊商標。
【VIP专享】AB RSLOGIX5000安装教程
AB RSLogix 5000安装使用指导教程设备管理部 王东亮本教程以RSLogix 5000 V17.01版本为例，说明软件的安装以及PC与CPU连接方式的建立。
1、RSLogix5000安装点击RSLogix5000安装文件进行安装，按照提示进行。
输入序列号202024567，进行下一步。
软件默认安装在C盘，建议不要修改安装目录。
在语言选项内，选择”English”， 只安装英文版即可。
在版本选项，选择V17版本。
激活软件界面，不要选择“激活产品”选项，等安装完软件后再进行激活（安装授权）。
点击完成，结束安装。
正确安装完成，在开始菜单内显示如下：2、授权安装。
由于本教程只做为个人学习使用，授权使用网络上破解的版本。
下载地址：/s/1ntv1P0X。
打开授权文件，选择虚拟盘文件，打开。
点击连接，找到破解的授权，输入激活密码000000。
点击确定，创建虚拟盘T，显示如下，右下方图标显示虚拟盘为开启状态。
打开RSLogix5000 Utilities授权安装软件。
选择从T盘到C盘。
出现破解的授权，点击“MOVE”，将授权安装到C盘上。
将虚拟盘断开，点击右下方图标退出虚拟T 盘，授权安装完成，软件即可使用。
3、PC与CPU连接的建立。
打开RSLinx软件。
组态连接方式。
本教程以通过网线连接为例，建立一个连接。
选择“EtherNet/IP Drive”，点击“Add New”。
设置IP地址（与CPU IP地址在同一网段内）。
为连接取个名字，点击OK,创建完成。
连接设置。
4、网络连接测试方式实际工作中，经常需要测试网络是否正常。
这里介绍一种最常用的测试方法。
开始-运行-ping ip地址 –t，通过数据包接受情况可判定网络是否正常。
网络通讯不正常状态：网络通讯正常状态：。
(仅供参考)RSLogix5000手册
AB_RSLogix5000初级使用手册目录：设定笔记本IP地址 (3)查看PLC硬件组态信息 (3)设定RSLinx (4)打开RSLogix5000软件创建与RSLinx相符的程序 (7)在RSLogix5000软件中创建程序章节、程序段落、程序自然段 (10)上传和下载程序 (13)创建行参 (16)RSLinx查看网络IP以及硬件 (18)PLC静态和动态IP地址分配 (21)Firmware刷新 (25)Rxlogx5000软件的在线修改功能 (28)Rxlogx5000软件的在线强制功能 (31)范围指令LIM需要注意的是，当Low Limit < High Limit数值时，LIM命令在Low Limit和High Limit之间的数值时输出。
如果Low Limit > High Limit数值时，LIM命令在Low Limit和High Limit之间的数值时停止输出。
(35)查找跳转、中断等子程序块的位置 (35)RSLogix5000软件的在线帮组功能 (36)Routine里程序的类型 (37)一个Project里可以最多建立32个Task，但只能有一个Task属性为Continuous （连续扫描）其余的31个Task可以分配给Event（事件扫描）或者Periodic（中断扫描）。
每一个Task里可以建100个Program，每一个Program可以建立无穷个routine。
(38)备份程序和解压程序 (41)程序的比较 (43)Flash Memory Card 程序备份和下载操作 (46)模拟量模块的组态、量程设定、模拟量输出的钳位设定。
(49)Device Net网络配置 (53)Device Net软件安装 (55)Device Net组网 (57)在RSLogix5000程序里添加DeviceNet硬件 (69)DeviceNet的硬件寻址 (71)配置EtherNet以太网远程I/O (75)实时监控趋势图 (81)EDS文件更新 (85)设定笔记本IP地址1．查看AB_PLC机器槽架上的CPU模块显示的IP地址，一般PLC的IP地址为为10.0.0.1，笔记本上的IP最后一位设置需要变化。
（完整word版）ABPLC（RSLogix5000）联机及刷硬件的方法
（完整word版）ABPLC（RSLogix5000）联机及刷硬件的方法AB PLC（RSLogix 5000）连接说明一、AB PLC常见的两种编程方式通讯设置：1.第一种是采用串口进行联机编程：AB PLC联机需要通过RSLinx Classic进行，只有先在RSLinx Classic找到相关站点的CPU，编程软件才能连接上，且此软件需另外安装，建议安装2.53以上的版本，安装好RSLinx Classic后，在下图Rockwell Software中打开RSLinx Classic：在RSLinx Classic的Communications菜单中选择Configure Drivers如下图：在弹出的对话框中点击Available Driver Types选择新建一个串口驱动：单击上图中的Add New按钮，输入名称后单击OK确认添加串口驱动，如下图直接确定：添加好串口驱动后弹出对话框设置串口通讯参数：如上图设置好串口通讯参数，与本机的串口通讯参数保持一致，修改完后点击OK确认即可，添加串口驱动后可随时点击上方的修改串口通讯参数：按上述步骤设置好串口驱动后，此时便可在RSLinx Classic的RSWho中看到PLC的各个模件（点击下图红色圈住的按钮）（注：此处截的图为以太网连接的，串口连接的与此类似）2.第二种是采用以太网进行联机编程：AB PLC采用以太网编程大体与通过串口编程类似，也需要通过RSLinx Classic进行，只有先在RSLinx Classic找到相关站点的CPU，编程软件才能连接上，且此软件需另外安装，建议安装2.53以上的版本，安装好RSLinx Classic后，与串口编程方式不同，采用以太网编程需先CPU出厂默认MAC地址改为以太网IP，首次更改IP通过伴随知道安装的BOOTP/DHCP Sever软件进行，如下图所示找到并打开BOOTP/DHCP Sever：如下两幅图所示在打开的软件中先选择T ools菜单中的Network Settings选项中将Subnet mask设置为255.255.255.0，其他可以默认，点击OK 确认。
RSLogix5000系统伺服轴属性说明（收藏）
RSLogix5000系统伺服轴属性说明（收藏）RSLogix5000系统伺服轴属性说明1. General (2)2. Motion Planner (4)3. Unit (6)4. Drive/Motor (8)5. Motor Feedback (13)6. Aux Feedback (14)7. Conversion (15)8. Homing (17)9. Hookup (20)10. Tune (22)11. Dynamics (23)12. Gains (25)13. Output (30)14. Limits (32)15. Offset (35)16. Fault Action (36)17. Tag (40)1.GeneralUse this tab to do the following for an axis, of the data type AXIS_SERVO_DRIVE.§Configure the axis for Servo operation or for position Feedback Only.选择此轴是伺服操作还是仅⽤作反馈。
§Assign the axis, or terminate the assignment of an axis, to a Motion Group.将轴与运动组关联起来。
我们建的轴组名称为MG。
§Associate the axis with a 1756-M08SE motion module.§View the base node of the associated 1756- M08SE motion module.Note that RSLogix 5000 supports only one Motion Group tag per controller.When a parameter transitions to a read-only state, any pending changes to parameter values are lost, and the parameter reverts to the most recently saved parameter value.When multiple workstations connect to the same controller using RSLogix 5000 and invoke the Axis Wizard or Axis Properties dialog, the firmware allows only the first workstation to make any changes to axis attributes. The second workstation switches to a Read Only mode, indicated in the title bar, so that you may view the changes from that workstation, but not edit them.请注意，RSLogix 5000仅⽀持⼀个控制器对应⼀个运动组标签。
RSLogix 5000 用户使用手册.
Logix5000 控制系统中的 ControlNet 模块 1734-ACNR, 1756-CNB, 1756-CNBR, 1769-L32C, 1769-L35CR, 1784-PCC, 1784-PCIC, 1784-PCICS, 1784-PKTCS, 1788-CNC, 1788-CNCR, 1788-CNF, 1788-CNFR, 1794-ACN15, 1794-ACNR15, 1797-ACNR15用户手册重要的用户信息固态设备与机电设备在操作特性上有所不同。
Safety Guidelines for the Application,Installation and Maintenance of Solid State Controls(应用、安装和维护固态控制的安全原则 (出版号 SGI-1.1,可从当地 Rockwell Automation 销售部获取, 或通过/literature 在线获取介绍了固态设备和硬布线的机电设备之间的一些重要区别。
由于存在此区别,也由于固态设备的广泛应用,因此负责应用此设备的所有人员都必须清楚了解此设备的每次预期应用都能符合要求。
任何情况下, Rockwell Automation, Inc. 都不对因使用或应用此设备而导致的偶然性或间接性损害承担任何责任。
本手册中所包括的示例和图表仅用作说明性目的。
由于任何特定安装都涉及许多可变因素和条件,因此 Rockwell Automation, Inc 对根据示例和图表进行的实际使用不承担责任。
对于使用本手册中介绍的信息、电路、设备或软件, Rockwell Automation , Inc. 均不承担专利责任。
未经 Rockwell Automation, Inc. 的书面许可,禁止对本手册的内容进行全部或部分复制。
在整个手册中,我们在必要位置都使用了注释,使读者了解安全注意事项。
警告标识有关在危险环境中会导致爆炸的作法或情形的信息, 这种做法或情形可能会导致人身伤害或死亡、财产损害或经济损失。
转换RSLogix5000程序版本为低版本
转换RSLogix5000程序版本为低版本Method 1: Save as L5K format, modify L5K in text editor and attempt to re-import into a previous release.The following is an example of reverting a ControlLogix version 15 project back to ControlLogix version 13.1). Open the v15 ACD file with RSLogix 5000 software and 'SAVE AS' selecting the L5K format. Then close the ACD.2). Once the L5K file is created, use the Windows Explorer to browse to its location on the hard drive. Then double click the L5K file and it will open up witha text editor such as NOTEPAD.3). The L5K file contains at least three details requiring change. (example below)Import Export version: IE_VER := 2.x; (IE Versions are v15 = 2.6, v14 = 2.5, v13 = 2.4, v12 = 2.3, etc.)Controller Major version: Major := x,Module Local Major version: Major := x,4). After performing the edits, save these L5K changes with NOTEPAD.5). Use RSLogix 5000 software to select File > Open in order to import the modified L5K file. Once the L5K file is selected, click on OK. Another prompt will ask to [Save Imported Project As] in order to create a new ACD file. Give this ACD file a new name to prevent overwriting the original. Then use the version selection box to choose the version specified earlier within NOTEPAD.6). Click Import, and RSLogix 5000 should read the information into the previous version. There is a chance users may experience the following Error 754-80042B08 Invalid Type.7). If so, these errors are usually caused when NOTEPAD saves the L5K file using a unsupported encoding mode such as UTF-8.8). Reopen the L5K file back in NOTEPAD and SAVE AS using the same name, but this time make sure the encoding is ANSI formatted. Now repeat the Import procedure as in step 4.9). This time around the import should be successful. This example of converting v15 to v13 will alert to the user of 3 warnings of new features that version 15 contained, but areunavailable in version 13.--------------------------------------------------------------------------------------------------------------------------------------------------------------Importing C:\Rockwell Software\RSLogix 5000\Projects\Version_15_project.L5K into Version_13_project.ACD...Creating module: LocalCreating program: MainProgramCreating routine: MainRoutineCreating task: MainTaskWarning: Line 56: An error occurred while setting attribute TERMINATIONCHARS of ASCII ASCII (Signed value overflow.) Warning: Line 56: An error occurred while setting attribute SerialNumber of Controller Version_15_project (This property can not be set.)Warning: Line 56: An error occurred while setting attribute MatchProjectToController of Controller Version_15_project (Couldn't be found.)Complete - 0 error(s), 3 warning(s)--------------------------------------------------------------------------------------------------------------------------------------------------------------10). Warnings are OK and you may continue. If Errors were detected in the L5K file, then it's up to the user to go back into the L5K file with NOTEPAD and correct or remove the problems found. Below is an example of a 1756-L61 r15 controller attempting to revert back to RSLogix 5000 v11. This controller was introduced with version 12, so the import into version 11 cannot be performed.--------------------------------------------------------------------------------------------------------------------------------------------------------------Importing C:\Rockwell Software\RSLogix5000\Projects\Version_15_project.L5K into Version_11_project.ACD... Error: Line 21: The processor type in the import file is not supported. Complete - 1 error(s), 0 warning(s) --------------------------------------------------------------------------------------------------------------------------------------------------------------11). If errors were detected about syntax, I/O or communciaton module format, then it is up to the user to go back into the L5K file with NOTEPAD and correct or remove the problems found. NOTEPAD has a GOTO feature, under Edit menu, to take you to the line number in which the error was found. Sometimes it might be necessary to a create test project, in the previous release, that contains theproblem module. Then it can be saved into L5K format so the user has a template of how the previous verison expects to read the data.Method 2: Two different sessions of RSLogix 5000, copy and Paste routines and UDTs from one to the other, then export / import tags and descriptions.1). The method is pretty much self explainitory using the Windows clickboard to handle copy / paste commands.。
rslogix5000仿真软件使用教程(2024)
与其他自动化系统集成方法
2024/1/27
OPC接口集成
rslogix5000支持OPC接口标准，可以与支持OPC接口的自 动化设备或软件进行数据交换和集成。
Modbus协议集成
通过Modbus协议，rslogix5000可以与支持Modbus协议 的设备进行通信和数据交换，实现与不同厂商设备的互联 互通。
24
自定义函数库创建及应用
自定义函数库创建
用户可以根据实际需求，创建自定义函数库，将常用的控制逻辑或算法封装成函数，方
便在多个项目中复用。
函数库管理
rslogix5000提供函数库管理功能，可以对自定义函数库进行添加、删除、修改等操作 ，实现函数库的灵活管理。
2024/1/27
函数调用与参数传递
在项目中可以直接调用自定义函数库中的函数，实现控制逻辑的快速搭建。同时，支持 函数参数的传递和修改，提高了函数的灵活性和可重用性。
3. 选择安装路径和组件，建 议保持默认设置。
2024/1/27
2. 双击安装程序，按照提示 进行安装。
4. 等待安装完成，期间可能 需要输入序列号和其他信息 。
5
授权与激活方法
在安装过程中，需要输入有效的序列号和授权信息。
如果已经安装但未激活，可以在软件界面中找到“帮助”或“激活”选项 ，按照提示进行激活操作。
23
数据监控与记录功能实现
实时数据监控
利用rslogix5000的数据监控功能，可以实 时查看和监控PLC内部的数据变化，包括寄 存器、变量、位状态等。
2024/1/27
历史数据记录
软件支持历史数据记录功能，可以记录PLC运行过 程中的关键数据变化，便于后续分析和故障排查。