螺丝名词中英文对照
螺丝名称的中英文对照表
螺丝名称的中英⽂对照表螺丝名称的中英⽂对照表常⽤英⽂单词及简写形式？No. 单词简写中⽂？1 screw scr 螺丝？2 nut nut 螺母？3 washer wash 垫圈？4 head hd 头？5 thread thre 螺纹？6 coating coat 镀层？7 rivet riv 铆钉？8 standoff stdoff 内外六⾓钉？9 driver driv ⽳？10 hexagon hexa 六⾓？11 tooth tooth 齿？12 lock lck 锁？13 spring spr 弹簧？14 wave wave 波浪型？15 pitch pitch ⽛距？16 partial thread P T 半螺纹？17 PT PT ⼀种螺纹形式？18 Full Thread FT 全螺纹？19 silver silv 银？20 cone cone 锥形？21 Eco-syn Eco 30度⽛的⼀种螺纹？22 Thread Forming TF ⾃攻螺纹？23 Self Tapping self tapp ⾃切屑螺纹？24 pin pin 销？25 shaft Shaf 轴？26 steel St 铁？27 stainless steel SS 不锈钢？28 Brass(Cu) Bras(Cu) 铜？29 Aluminum AL 铝？30 Rubber Rub 橡胶？31 machine screw mech scr 机制螺丝？32 SEM screw SEM Scr 组合螺丝？33 Material material 材料？34 Grade GD 等级？35 Finish Finish 表⾯处理？36 Point Point 点？37 Clamp Clam 夹⼦？38 internal Int 内？39 external ext 外？40 thickness / 厚度？41 length / 长度？42 hole / 孔？43 Metric Metcric 公制？44 DIN / 德标？45 ANSI / 美标？46 JIS / ⽇标？47 ISO / 国际标准？48 NFE / 法标？49 GB / 国家标准？50 Quality / 质量？51 surface hardness 表⾯硬度？52 product treatment 表⾯处理？53 plating 电镀？54 heat 热？55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车⽤螺丝、轴⼼？56 Screws And Shafts For Sewing Maching 针车⽤螺丝、轴⼼？57 Socket Set Screws ⽌付螺丝？58 Stainless Steel Coarse Thread Screws 不锈钢宽⽛螺丝？59 Stainless Steel High-Low Thread Screws 不锈钢⾼低⽛螺丝？60 Stainless Steel Machine Screws 不锈钢机械螺丝？61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝？62 Stainless Steel Self Tapping Screws 不锈钢螺丝class=a1>⾃攻螺丝？63 Stainless Steel Thread Cutting Screws 不锈钢⾃削螺丝？64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三⾓⽛螺丝？65 Steel Ceiling Anchors 插⽚壁虎？66 Drop in Anchors 内迫壁虎？67 Steel Hit Anchors 碳钢锤钉壁虎？68 Steel Hex Coupling Nuts 碳钢六⾓螺帽？69 Wedge Anchors 强⼒车修壁虎？70 Cut Anchors 外迫壁虎？71 Chemical Anchors 化学壁虎？72 Heavy Duty Expansion Anchors 不锈钢重载胀栓？73 Tie Wire Anchors 鱼眼壁虎?企眼长螺帽?74 Hammer Drive Anchors 锌合⾦打⼊式壁虎?75 Strut Nuts 弹簧螺帽??76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列?77 ?Nylon Frame Anchors or Metalframe Anchors 门窗、地板专⽤壁虎?78 Hollow Wall Anchors ⽯膏板中空壁虎?79 Sleeve Anchors 套管式壁虎?80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打⼊式壁虎鱼形尼龙壁虎 ?81 Hit Anchors 强⼒式锤钉壁虎?82 Bolt Anchors 电梯壁虎?83 Heavy duty anchors 重载壁虎?84 Loxin Masonry Anchors 两⽚夹?85 Set Bolts 定位螺栓?86 Short Strap Anchors 长型兰花夹?87 Drop in Setting Tools ⼯具棒?88 Elephant foot anchors 象脚壁虎?89 Concrete Insert ⽔泥预埋件?90 Drop in Anchor with Lip 翻边胀轴?91 Legs Drywall Anchors 冲件?92 Hex Cap Nuts 六⾓盖头螺帽?93 Hex Serrated Nuts 六⾓锯齿螺帽??94 Hex Flange Nuts 六⾓轮缘螺帽??95 Hex Coupling Nuts(High Nuts) ⾼脚螺帽?96 Round Nuts 圆螺帽?97 Square Nuts 四⾓螺帽?98 Pipe Nuts 管⽤螺帽?99 Wheel Nuts 轮壳螺帽?100 Wing Nuts 蝶型螺帽?101 U Nuts U形螺帽??102 T Nuts T形螺帽?103 Eye Nuts 环⾸螺帽?104 Kep Nuts 齿形螺帽??105 Clinch Nuts 齿花螺帽?106 Corten Steel Heavy Hex Nuts 耐候钢六⾓重型螺帽?107 Weld Nuts 焊接螺帽?108 Heigh Strength Nuts ⾼张⼒螺帽?109 Structural Nuts 建业⽤螺帽?110 Stainless Steel Nuts 不锈钢螺帽?111 Brass Nuts 铜螺帽?112 Aluminum Nuts 铝螺帽?113 Alloy Steel Nuts 合⾦钢螺帽?114 Heavy Duty Wheel Hub Nuts 重型车螺帽?115 Acorn Cap Nuts 铁器焊接袋帽?116 All-Metal Prevailing Torque Type Nuts ⾦属预置扭矩式螺帽?117 Anchor Nuts 壁虎螺帽?118 Big Size Nuts ⼤尺⼨螺帽?119 Closed End Acorn Nuts 铁盖袋帽?120 Conical Washer Nuts 盘形华司螺帽?121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽?122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽?123 Flat Waser Nuts 平⾯华司螺帽?124 Hex Slotted Nut 六⾓割沟螺帽?125 Self-Locking Nuts ⾃锁螺帽?126 Sliding Nuts 制⽌螺帽?127 Sln Self-Locking Nuts Sln-⾃动防松螺帽?128 Special Nuts 其它特殊螺帽?129 Spring Nuts 弹簧螺帽?130 Stainless Steel Flange Nuts 不锈钢突缘螺帽?131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六⾓轮缘尼龙螺帽? 132 Stainless Steel Heavy Hex Nuts 不锈钢六⾓重型螺帽?133 Stainless Steel Hex Nuts 不锈钢六⾓螺帽?134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌⼊螺帽?135 Hex Nuts 普通六⾓螺帽?136 Heavy Hex Nuts 六⾓重型螺帽?137 Hex Jam Nuts 薄型螺帽?138 Nylon Insert Lock Nuts 尼龙嵌⼊防松螺帽?139 Hex Machine Screw Nut 机械螺丝⽤六⾓螺帽? 140 Hex Head Cap Screws(Hex Bolts) 六⾓螺丝(栓)? 141 Hex Head Machine Bolts 六⾓机械螺丝?142 Hex Lag Bolts 六⾓⽊⽛螺丝?143 Square Head Bolts 四⾓螺丝?144 Carriage Bolts 马车。
的螺钉术语中英文对照
•acme screw thread爱克米螺纹•acme screw-thread阿克米制螺纹•adapter set screw接头调节螺钉•adjustable round split die with adjusting screw带调整螺钉的可调式圆板牙•adjustable screw type steering gear可调整式螺旋型转向装置•adjustable stop screw可调整止动螺钉•adjusting screw调整螺钉;调整螺丝;调准螺旋;调节螺钉;校正螺钉;校正螺旋•adjusting screw for elevation标高调整螺丝•adjusting screw for pan position锅体水平调节螺杆•adjusting screw for transverse横向调整螺丝•aerial screw飞机螺旋桨•aiming adjust screw瞄准调节螺钉•aiming screw瞄准调节螺钉•air intake adjusting screw进气调节螺钉•air screw空气螺旋桨•air-tight screw pump密闭式螺杆泵•Allen screw阿伦螺钉•allen screw六角固定螺丝•ampere's right handed screw rule安培右手螺旋定则•Ampere's right-hander screw rule安培右手定则•anchor screw基础螺栓•anchoring screw止动螺钉•annular screw plate环状板牙•antagonizing screw调置螺旋•antifriction ring holder screw减摩环托螺钉•arachnoid screw蛛网膜螺钉•arachnoid screw driver蛛网膜螺钉旋凿•Archimedean screw阿基米德螺线•Archimedean screw pump阿基米德螺旋泵•Archimedes'screw阿基米德螺旋•assembly screw安装螺旋•attachment screw连接螺钉;定位螺丝;止动螺钉•automatic screw lathe自动螺纹车床•automatic screw machine自动螺丝车床•auxiliary screw arc辅助螺钉弧形板•axis of screw螺旋轴线•azimuth adjusting screw方位调整螺钉•backing-up screw止动螺钉•backlash adjusting screw齿隙调整螺钉•ball screw滚珠丝杠•ball-bearing cap screw滚珠轴承盖螺钉•ball-jointed screw万向球铰螺杆•band wheel crank screw带轮曲柄螺丝•band wheel crank screw nut带轮曲柄螺丝帽•band wheel set screw带轮主头螺丝•banking screw止动螺钉•base screw底座螺钉•bearing for screw conveyer螺旋输送机轴承•bell screw钟形螺钉;丝锥接套•binding(post)screw接线螺钉•binding head screw扁头结合螺钉•blast cap screw鼓风盖螺钉•bleed screw带孔螺钉•body of screw螺钉体•body screw犁体螺钉•boiler lagging plate set screw锅炉套板止动螺钉•bolster screw jack车架螺旋千斤顶•bone screw接骨螺钉•bone screw and bolt outfit骨螺钉螺栓器械包•bone screw driver接骨螺钉旋凿•bone screw holding forceps接骨螺钉夹持钳•bone screw tap接骨螺钉丝攻•bottle screw螺旋起重机;螺旋起重器•bottom plate screw底板螺钉•brace screw撑柱螺丝•brace screw driver撑臂起子•brake screw制动螺杆•brake thrust screw制动器止推调节螺钉•brass countersunk head wood screw黄铜平头木螺丝•brass round head wood screw黄铜圆头木螺丝•brass screw down bib cock黄铜水龙头•brass screw down bib cock heavy type黄铜重型水龙头•brass shouldered cup screw hook黄铜螺丝弯钩•brass square screw hook黄铜螺丝曲尺钩•brass wood screw黄铜木螺丝•brass-plated mild steel round bead wood screw镀黄铜圆头软钢木螺丝•brass-plated mild steel round head machine screw镀黄铜圆头软钢机器螺丝•brazier head screw扁头螺钉•breaker arm adjusting screw断电臂调整螺钉•bright mild steel countersunk head wood screw光亮软钢平头木螺丝•bright mild steel round head wood screw光亮软钢圆头木螺丝•bronze screw hook古铜螺丝钩•bush set screw衬套制动螺钉•butterfly screw元宝螺钉•button-head cap screw圆头帽螺钉;半圆头紧固螺钉•button-head screw圆头螺钉•button-headed screw半圆头螺钉•buttress thread screw斜梯形纹螺钉•calibration screw校准螺钉•cap of screw螺钉帽•cap screw有头螺钉•capstan(-headed)screw绞盘螺钉•captive screw外加螺丝•carpenter's screw clamp台钳•carriage lock screw拖板锁紧螺钉•casale closure with external screw外螺纹卡扎里密封•central screw中心螺钉•centrifugal screw pump离心螺旋泵•centring screw定中心螺钉•chain adjusting screw链调节螺钉•chamfer head screw沉头螺钉•check screw止动螺钉•cheese head screw高平头螺丝•circumferential register screw圆周定位螺丝•clamp screw制动螺旋•clamp screw sextant制动螺钉六分仪•clamping screw固定螺钉•clip screw调置螺旋•closing screw螺纹规;螺纹塞•clutch adjusting screw离合器调整螺钉•clutch pressure plate screw离合器压板螺钉•coach screw方头螺钉;板头尖端木螺钉•coarse screw tap粗丝锥•coarse thread screw粗螺纹螺钉;粗纹螺钉•coarse-pitch screw大螺距螺钉•collar head screw头带缘螺钉•collar-head screw环头螺钉•combination screw driver set with tester带测电笔的套装螺丝刀•complete equipment for making wood screw木螺丝成套设备•compound feed-screw复式刀架丝杠•compound feed-screw graduated collar复刀架丝杠刻度圈•compound screw复式螺钉;复式螺旋•cone screw锥形螺钉•conical twin-screw extruder锥形双螺杆挤塑机•connecting screw rod连接螺杆•connection screw连接螺钉•constant taper screw等螺距锥体螺杆•contact screw接触螺钉•conveyer screw螺旋输送器•conveyer screw drive shaft输送机螺旋主动轴•conveyer screw shaft输送机螺旋轴•conveyer screw shaft coupling输送机螺旋轴联轴节•conveyer screw thrust plate输送螺旋止推板•copper-plated iron screw ring镀紫铜铁吊环螺钉•cored screw空心螺旋•correction screw校正螺钉;校正螺旋•correctional screw改正螺旋•cotter with screw end螺旋端锁销•countersunk head machine screw埋头机螺钉•countersunk head screw埋头螺钉•countersunk oval head screw埋头圆顶螺钉•countersunk screw埋头螺钉;埋头螺丝•coupling screw连接螺钉•cover screw盖用螺钉•credit screw信用紧缩•crest of screw thread螺纹牙顶•cross feed screw横进刀螺杆•cross feed screw crank横向进刀螺杆曲柄•cross feed screw dial横进刀螺杆指示盘;横向进刀螺杆指示盘•cross feed screw handle横向进刀丝杠手柄•cross lead screw横向丝杆•cross lead screw nut横向丝杆螺母•cross recess head screw十字槽头螺钉•cross screw左右交叉螺纹•cross slide screw横动台螺杆;横滑板螺杆•cross surfacing screw横动台螺杆•cross traverse screw横动台螺杆•crown screw牙冠用螺钉•cruciform screw driver十字形螺丝起子•cruciform slot screw十字槽螺钉•cup head screw半圆头螺钉;圆头螺钉•cup head wood screw圆头木螺丝;半圆头木螺钉•current regulator contact screw电流调节器接触螺钉•cutter for screw plate螺丝板加工刀具;螺丝板牙加工工具•decreasing lead screw减螺距螺杆•depth gauge for bone screw接骨螺钉长度测量器•depth screw gear耕深调节螺杆•depth-adjusting screw耕深调节螺杆•dial of vertical adjustable screw垂直可调丝杠•dial screw度盘螺钉•diameter of screw螺纹标称直径;螺旋直径•differential drive gear thrust screw差速器环齿轮推力螺钉•differential gear for screw conveyer螺旋输送机的差动装置•differential screw差动螺旋;差动装置螺钉•differential screw gearing差动螺旋传动装置•differential screw jack差动螺旋起重器•differential screw-jack差动螺旋千斤顶•differential-screw jack差动千斤顶•diopter rotating screw视度转螺•distributor adjusting screw分配调整器螺钉•dog(set;locating)screw定位螺钉•dog screw轧头螺钉;偏心头螺钉•dormant screw埋头螺钉•double flight feed screw双头螺旋加料器•double screw pump双螺杆泵•double worm screw双扭螺钻;麻花钻•double-screw bolt螺柱•double-screw washer双螺旋洗矿机•double-thread screw双头螺纹•double-threaded screw双纹螺钉•dowel screw扶手螺丝;两头螺钉;两头螺丝钉•down-feed screw垂直丝杠•draw screw起拉螺钉;起模螺钉•drive screw螺纹钉•driving screw导螺杆;导螺旋;主螺杆•drivre screw传动螺杆•duct adjusting screw墨斗调节螺丝•earth screw土钻;挖穴钻•earthing screw接地螺钉•eccentric-screw breechblock偏心闭锁机•Edison screw爱迪生螺纹;圆螺纹•electric screw clay gun电动螺旋式泥炮•electric screw down gear电动压下装置•electric screw driver电动螺丝刀;电动螺旋钻•electro-magnet screw press电磁螺旋压力机•electro-mechanical screw time release机电螺旋式限时解锁器•elevating endless screw升降蜗杆•elevating screw升降丝杠;上升螺旋;螺旋起重器•elevator screw升降机螺旋•endless screw蜗杆•endless tangent screw sextant微调螺杆六分仪•engine idling speed adjusting screw发动机怠速调整螺丝•English screw英制螺纹•English screw pitch ga(u)ge英制螺距规•Ericsson screw埃里克森螺纹•expansion screw扩开螺钉;可调螺钉•extension screw螺旋延长部•external screw螺钉•external screw cutting tool外螺纹车刀•external screw ga(u)ge外螺纹检查规•external screw thread finish外螺纹瓶口•extra fine screw特细牙螺纹•extruder screw压出机螺杆•extruding screw挤压螺杆•eye screw羊眼螺丝;吊环螺栓;环首螺钉;环首螺栓•eyepiece screw目镜螺丝;目镜螺旋•eyepiece screw-micrometer螺杆式目镜测微计•faceplate screw面板螺丝•faller screw针板螺杆•falt fillister screw凹槽扁头螺杆•fastening screw紧固螺钉•feed screw进给螺杆;螺旋给料机;螺旋送料机•feed screw collar进给螺杆挡环•feed screw mechanism进料螺杆机构•feed screw nut丝杆螺母•female screw阴螺丝;阴螺旋;螺母;内螺旋•female screw thread内螺纹•femoral screw股骨螺钉•ferrous and non-ferrous screw and nut黑色及有色金属螺钉和螺母•fillet of screw螺纹圈•filling screw螺纹规•fillister head screw凹槽帽螺钉•fine adjustment screw微调螺丝•fine screw tap细牙螺丝攻•fine thread screw细纹螺钉•fine-motion screw微动螺旋•fine-pitch screw细牙螺钉•finite-conductivity screw instability有限电导率螺旋不稳定性•fitting screw紧配连接螺栓;装配螺钉•fix screw固定螺丝•fixation screw needle固定螺丝针•flat counter-sunk head screw平顶埋头螺钉•flat end set screw平端固定螺钉•flat head screw平头螺钉;平头螺丝•flat point set screw平端定位螺钉•flat screw平头螺钉•flexible screw conveyer挠性螺旋输送器•flush head screw shackle平头螺栓卸扣•flux screw磁通调整螺钉•fly-headed screw蝶形头螺钉•focusing screw调焦螺旋•foot screw地脚螺钉;地脚螺丝;脚螺旋•foot-screw底脚螺丝•for screw stays用于螺丝固定•force screw力旋量•forcing screw紧固螺钉;起重器;加压螺钉•forked screw driver叉形螺丝刀;叉形螺旋起子•four-screw driver四用螺钉起子•four-screw leveling head四螺钉安平头•four-wheel screw jack四轮修车起重器;四轮修车起重器•friction screw press摩擦螺旋压力机;摩擦压力机•front screw前螺杆•fuel pump adjusting screw燃油泵调节螺钉•full-automatic screw machine全自动螺丝机床•full-flighted screw全程螺杆•fully automatic turret screw machine全自动转塔式车床•galvanized iron corn head screw镀锌尖头螺丝•galvanized iron screw白铁螺丝•galvanized iron screw hook镀锌螺钩•galvanized mild steel countersunk head wood screw镀锌沉头木螺丝•galvanized mild steel drive screw镀锌螺丝钉•galvanized mild steel roofing screw镀锌瓦楞螺丝•galvanized mild steel round head machine screw镀锌圆头机器螺丝•galvanized mild steel round head wood screw镀锌圆头木螺丝•galvanized MS countersunk head machine screw镀锌平头机器螺丝•galvanized screw镀锌螺钉;镀锌螺丝•galvanized screw plug镀锌旋塞•galvanized stay adjustable screw镀锌拉线调整螺丝•galvanized steel self tapping screw镀锌自攻螺线•gas valve screw气阀螺钉•gathering screw收集螺旋•gear motor for screw conveyer螺旋输送器减速电动机•geared worm screw传动蜗杆螺旋•generator frame through screw发电机架长螺杆•gib screw调整楔用螺钉;夹紧调整螺钉•governing screw调节螺钉•governor adjusting screw调节器调整螺钉•governor adjusting screw cap调速器调整螺钉帽•governor arm screw调速器杆螺钉•governor link screw调节器联杆螺钉•grain screw谷粒螺旋•grid of screw dislocations螺形位错十字格•grooved bone screw有槽接骨螺钉•ground screw地脚螺钉•grub screw平头螺钉;平头螺丝;木螺钉;木螺丝•guide screw导螺;丝杆•hairspring screw游丝螺钉•hairspring stud screw游丝外桩螺钉•half-bright screw半光制螺钉•half-round head screw半圆头螺丝•half-round screw半圆头螺钉•hammer-drive screw锤入式螺钉•hand brake band anchor bar adjusting screw手闸带锚定杆调整螺钉•hand driven screw press手动平板机•hand jack screw手力千斤顶•hand power screw press手动螺旋压机•hand power screw punching press手动螺旋压孔机•hand screw手动螺杆;手力千斤顶•hand screw clamp手螺旋夹•hand screw holdfast手螺旋夹•hand screw press手动螺旋压力机;手转压力机•hand screw tap手用丝锥•hand wheel screw down手轮压下装置•hand-operated screw press手动螺旋压力机•hand-operated vertical screw press手摇立式螺旋压榨机•hand-screw手动起重器•hand-screw vulcanizing press手旋硫化机•handle set screw车辆制动螺钉•handrail screw扶手螺丝•head lamp adjusting screw前灯调节螺钉•headless screw无头螺钉•headless set screw无头止动螺丝•headless shoulder screw无头轴肩螺钉•helical screw pulp conveyer螺旋纸浆传送器•helically bladed screw conveyer螺旋叶片式输送器•hermetic screw pump密闭式螺杆泵•hex socket screw key六角凹头螺钉键•hexagon cap screw六角帽螺钉•hexagonal head screw六角头螺钉;六角头螺栓•hexagonal socket screw六角凹头螺钉•high power screw press高能螺旋压力机•high precision lead-screw cutting lathe高精度丝杠车床•high viscosity triple screw pump高粘度三螺杆泵•holding screw紧定螺钉;紧固螺丝•holes for screw螺栓孔•hollow screw空心螺钉•hollow-head set-screw空心头固定螺钉•hook screw钩头螺钉;带钩螺钉•horizontal clamping screw水平制动螺钉•horizontal light beam adjusting screw水平光调节螺钉•horizontal parallax screw水平视差螺旋•horizontal screw pump卧式螺旋泵•housing adjusting screw压下调整螺丝•housing screw压下螺丝•Hunter's screw差动可逆可螺旋桨•hydraulic cylinder bleeder screw液压缸放出管螺钉•hydraulic screw press液压螺旋压力机•hyperbolic screw pump双曲线式螺杆泵•image screw映像旋量•impedance screw节流螺钉•impeller locking screw叶轮端螺钉•inboard screw内侧螺旋桨•inch screw die英制螺纹板牙•inch screw tap英制螺纹丝锥•independent screw chuck分动螺旋卡盘•inside screw螺母•inside screw and non-rising stem暗杆内螺纹•inside screw and rising stem(ISRS)明杆内螺纹•inside screw rising stem内螺纹明杆•instrument headed screw半埋头螺钉•internal screw内螺旋•internal screw cutting tool内螺纹车刀•internal screw finish内螺纹瓶口•internal screw ga(u)ge内螺纹规•internal screw pump内螺旋泵•internal screw thread内螺纹•international screw die公制螺丝钢板•international screw pitch gauge国际螺距规;国际螺距规•international screw tap公制丝锥•international screw thread国际标准螺纹•interrupted screw带槽螺钉•iron handle screw driver铁柄螺丝刀•iron screw铁螺钉•iron screw with square head方头铁螺钉•iron square head screw方头铁螺钉•iron wood screw铁制木螺钉•jack screw螺旋起重机;千斤顶螺杆;千斤顶螺丝•jack(ing)screw螺旋千斤顶•jacket band screw套带螺钉•jacking screw顶起螺丝•key screw螺丝把;螺旋键•kingpin stop screw主销定位螺丝•knuckle stop screw关节止动螺钉•knurled screw滚花螺钉;滚花螺杆•lag screw板头尖端木螺钉;方头螺钉•lag wood screw木螺钉•lang raising screw地轮起落螺杆•large flat head slotted screw大平槽头螺钉•latch bracket screw弹键托螺钉•latch screw弹键螺钉;门栓大螺丝•lead of screw螺旋导程•lead screw导螺杆;唱片盘首纹;丝杆;丝杠;引入槽•lead screw for cross-slide横向进给螺杆•lead screw for saddle床鞍螺杆•lead screw for top slide刀架螺杆•lead screw monocomparator导杆螺旋单象坐标仪•lead screw tester丝杆检查仪•lead-in screw引入螺钉•lead-screw导螺杠•lead-screw drive导螺杆驱动•lead-screw gear丝杠交换齿轮•leading screw lathe丝杠车床•leading screw support导螺杆轴承•left screw左螺旋•left-hand screw左螺旋•left-hand screw drill pipe反扣钻杆•left-handed screw左旋螺杆•lentil-headed screw扁头螺钉•level(l)ing screw校平螺旋•levelling screw水准螺旋•lever latch cap screw手柄弹键盖螺钉•lift link screw提升杆调整螺杆•lift(ing)screw螺旋起重器•lifting screw起模螺钉;千斤顶螺杆;升降螺杆•limit screw止动螺钉•limit screw pitch ga(u)ge螺距极限规•linkage levelling screw悬挂装置;调平螺杆•lock screw锁定螺钉•locking screw锁紧螺钉•log screw方头木螺丝;木螺钉;木螺丝•long bent point screw长弯头画线针•long lead screw长丝杠•long screw长螺丝•longitudinal parallax screw纵向视差螺旋•low noise air screw compressor低噪声螺杆空气压缩机•lubricating screw润滑螺旋;黄油枪•machine screw with oval countersunk fillister head半沉头螺钉•main(driving)screw主螺杆•main pin brass cotter set screw主销铜衬扁销止动螺钉•main valve head cap screw主阀盖有头螺钉•male screw阳螺旋;柱螺纹•male screw cutting tool外螺纹车刀•male screw thread外螺纹;阳螺纹•manual control screw手调螺钉•manually-operated screw手动压力螺丝•marine screw propeller船用螺旋桨•marking screw标号螺丝•marsh screw amphibian沼地螺旋推进水陆两用车•mass screw平衡螺钉•master screw母丝杠;标准螺旋•Maurer type screw press毛雷尔型螺旋压榨机•maximum fuel limit screw最大燃油限制螺钉•meantime screw调时螺钉•measuring screw测微螺丝•medium Edison screw-cap中等爱迪生螺旋灯头•medium egg-plant screw indicating lamp bulb中螺口茄形指示灯泡•meter screw公制螺纹•metering screw计量螺旋•metric screw pitch gauge米制螺距规;国际螺距规•metric screw thread公制粗牙螺纹;公制螺纹•micrometer adjusting screw微调螺钉•micrometer screw千分丝杠;微调螺钉•micrometer screw caliper测微螺旋卡尺•micrometer screw ga(u)ge螺旋测微计;螺旋千分尺•micrometric regulating screw微调螺钉•micrometric screw测微螺杆;测微螺旋•mill headed screw滚花头螺钉•mill screw轧机压下螺丝•milled edge thumb screw铣边翼形螺钉•milled screw滚花头螺钉•minimum fuel limit screw最小燃油限止螺钉•minus screw一字槽头螺钉•mirror screw镜螺旋;镜螺旋;镜面螺钉;镜面螺钉•mixer-with conical screw锥形螺旋搅拌机•mixing screw螺旋混合机;混合螺杆;混合用螺旋•mixing screw conveyer混合螺旋输送器•monkey screw wrench活扳手•mounting screw安装螺钉•multi-start screw thread多头螺纹•multiple-start screw thread多头螺纹•multiple-thread screw多头螺杆•multiple-threaded screw多头螺杆;多纹螺旋•mushroom head screw菌头螺钉;菌头螺钉•Napier's differential screw steering gear纳皮尔差动螺旋操舵装置•neck(ed)screw颈口螺旋;颈口螺旋•needle bar connecting link hinge screw麦果螺丝•nickel-plated double line iron screw hood镀镍双线螺旋帽•nickel-plated double line iron screw hook镀镍双线螺旋钩•nickel-plated iron screw eye镀镍铁螺丝眼•nickel-plated iron screw hook镀镍铁螺旋钩•nickel-plated mild steel round head machine screw镀镍低碳钢圆头机器螺丝•nickel-plated mild steel round head wood screw镀镍低碳钢圆头木螺丝•nickel-plated steel self tapping screw镀镍钢制自攻螺丝•no screw balance无平衡螺钉摆轮•nozzle adjusting screw喷管调节螺钉•nut screw螺母•observation tube fixing screw抽筒固定螺旋•odd-pitch screw非标准螺纹•oil cup cover screw油杯盖螺钉•oil pressure adjusting screw油压调节螺钉•oil pressure switch screw油压开关螺丝•oil reservoir cover screw储油器盖止动螺钉•oil-hole screw油孔螺钉•oil-pressure adjusting screw油压的调节螺丝•one start screw单头螺纹•open screw gill drawing frame单针并条机•oscillating screw摆动螺钉•outer set screw外固定螺钉•outside screw and yoke type(OS&Y)轭式外螺纹•outside screw non-bonnet(OSNB)无压盖外螺纹•oval countersunk fillister head machine screw半沉头机器螺钉•oval countersunk fillister head wood screw半沉头木螺钉•oval countersunk screw椭圆埋头螺钉•oval fillister head screw球面圆柱头螺钉•oval head screw椭圆头螺丝•oval slotted countersunk head unloosing screw半沉头不脱出螺钉•packing screw衬垫螺旋•paddle screw conveyer叶片式螺旋输送器•panhead screw大柱头螺钉;锅头螺丝•pattern screw起模螺钉•percussion screw press直接电动螺旋锤;直接电动螺旋压力机•Persian screw螺旋排水机•Philips screw菲氏螺钉;带十字槽头的螺钉•Phillips screw菲利浦螺钉;十字槽螺钉•pilot screw支持螺丝•pinching screw夹紧螺钉;固定螺钉•pipe screw-cutting lathe管子螺纹车床•piston heat set screw活塞头止动螺钉•piston pin locking screw活塞销锁紧螺钉•piston pin set screw活塞销锁紧螺钉•piston stop screw活塞头止动螺钉•pivot screw枢轴螺钉•pivot-point screw枢轴螺旋•plain bone screw无槽接骨螺钉•plain screw平螺钉•plain-ended screw平端螺钉•plug machine screw tap机用中丝锥•plug screw螺塞•plug screw ga(u)ge阴螺纹规•plus screw十字槽头螺钉•plus-minus screw调整螺钉;调整螺丝;调整用螺钉•pneumatic screw press气动螺旋压机•pointless screw平端螺钉•porcelain head screw瓷头螺丝•porcelain screw holder瓷螺丝灯头•porcelain screw socket瓷螺丝灯座•positioning screw定位螺钉•positive-column screw instability螺旋不稳定性•positive-displacement screw type compressor正排量螺旋式压气机•pottery topped brass screw瓷头铜螺丝•power screw传动螺杆;传力螺钉•power transmission screw动力传动螺杆•power-driven screw-jack set电动螺旋起重机组•precision lead screw精密丝杠•pressure regulating thumb screw压脚调节翼形螺钉•pressure screw压力螺钉;压下螺丝•pressure screw check nut压力螺钉防松螺母•pressure screw extractor螺旋压榨机•pressure-adjusting screw压力调整螺钉•proportion set screw比例度设定螺丝•pull-out piece spring screw压簧螺钉•push-pull screw推拉螺杆•pusher screw推进式螺旋桨•quadruple screw四头螺旋;四纹螺旋;四线螺旋•quadruple screw motor ship四螺旋桨船•quick-motion screw速动螺旋•radial feed screw径向进给丝杠;径向进给丝杠•radiator screw-cap散热器加水盖•rag screw棘螺栓•raised head screw凸头螺钉•rapid screw大节距螺钉•ratchet screw jack棘轮螺旋起重器•reaming holes for screw stays为固定螺钉用的铰孔•rear furrow wheel adjustment screw尾轮调节螺钉•rear screw shaft后螺旋桨•rear screw shaft bushing后螺轴衬套•recalibration screw重新校准螺钉•recessed-head screw-driver槽头螺丝刀•rectilinear screw-thread reluctance motor直线螺纹磁阻电动机•reduction screw螺旋还原反应器•regular screw thread基本螺纹•regular screw threads普通螺纹•regular thumb screw对称翼形螺钉•regulating screw调整螺钉;调整螺丝•regulating stem set screw调节杆止动螺钉•regulator spring screw调节簧螺钉•restriction screw节流尖头螺钉;节流螺旋杆;带螺纹针阀•restrictor screw节制孔螺钉•retainer screw护圈螺钉•retaining screw固定螺钉•retention screw止动螺钉;定位螺钉;紧固螺钉•reverse screw回动丝杠•reverse-flighted screw双向螺杆•reversing screw回动螺旋•reversing screw bolt回动螺栓•reversing screw bottom guide回动螺杆下导板•reversing screw gudgeon回动螺旋•reversing screw top guide回动螺旋上导板•revolution speed of screw螺旋转速•ribbon type screw conveyer带状螺旋运输机•rigging screw装配螺钉;松紧螺旋扣;系紧螺钉•rigging-and-left-hand-screw clip左右向螺杆夹•right-and-left screw左右旋螺栓•right-hand screw右螺旋•right-hand screw rule右手螺旋定则•right-hand screw thread右螺纹;右旋螺纹•right-handed screw右旋螺钉;右旋螺旋杆•right-handed thread screw右螺纹螺杆•ring screw环头螺钉•ring screw ga(u)ge螺纹环规•rolled-thread screw滚丝螺钉•rolling mill screw down轧机的压下装置•rotary helical screw compressor回转式螺杆压缩机•rotary screw compressor旋转螺旋压缩机•rotation set screw转动限位螺钉•round head wood screw圆头木螺钉•round wood screw圆头木螺钉•roundhead screw圆头螺钉•roundheaded wood screw圆头木螺丝•saddle feed screw鞍架进给螺杆•saddle traverse screw鞍架进给螺杆•safety locking screw保险止动螺钉•safety set screw安全螺丝;安全止动螺钉•scoketed screw凹头螺钉•screw螺钉;螺丝;螺旋•screw action捻旋作用•screw adjusting double caliper螺钉调整内外卡尺•screw adjusting inside caliper螺钉调整内卡尺•screw adjusting outside caliper螺钉调整外卡尺•screw adjustment螺钉调整•screw and double nut螺丝和双螺母•screw arbor螺杆•screw auger推运螺旋•screw axes螺旋对称轴•screw axis螺旋轴•screw base螺钉座•screw base fuse螺旋式熔断器•screw bell钻杆打捞器•screw belt螺钉带•screw belt fastener螺钉带扣•screw blade螺旋刀片;螺旋桨叶;螺旋式叶片•screw blank螺钉坯件•screw bolt螺杆;螺栓;全螺纹螺栓•screw bolt and nut螺栓和螺母•screw brake螺杆闸•screw bushing螺旋轴衬•screw cap螺母;螺丝管帽;螺丝帽•screw capping拧盖•screw case螺杆箱•screw case box螺杆箱机座•screw case suppressing metal螺杆箱紧固件•screw chaser螺纹板牙;螺纹梳刀;修正孔用丝锥•screw chases螺丝版框•screw chasing螺纹切削•screw chasing machine螺丝车床;螺纹切削机;制螺旋机•screw chasing tool螺纹梳刀•screw clamp螺丝夹;螺旋夹•screw clamp for brake shoe lining装制动磨擦夹片•screw clamp for lubricating leaf spring钢板弹簧上油卡子•screw coal conveyer螺旋式输煤机•screw coal unloader螺旋卸煤机•screw collar螺旋环;环状螺母•screw comb螺纹梳刀•screw composing-stick螺丝排字手托•screw compressor螺旋压气机;螺旋压缩机•screw compressor clamp螺旋压缩机管夹•screw cone螺旋锥体•screw contact螺丝触点•screw control压下控制•screw conveyer螺旋输送机•screw correction螺旋形失真校正•screw cramp螺丝夹钳•screw cutter螺纹刀具•screw cutting螺纹切削;切螺纹;切削螺纹;车螺纹•screw cutting dies板牙•screw cutting lathe车螺丝车床;螺丝车床•screw cutting machine螺纹切削机;螺旋切削机•screw decanter螺旋沉降器;螺旋澄清器•screw depth control螺杆式深度调节器•screw depth regulator螺旋式入土深度调节器•screw diad二重螺旋轴•screw diameter螺旋直径•screw die螺丝板牙;平丝板•screw dislocation螺线位错;螺旋位错•screw displacement螺旋位移•screw drive螺杆传动•screw driver螺丝批•screw driver with wooden scales夹柄螺丝批•screw drum螺旋转鼓•screw elevator螺旋升运器;螺旋式升降机;螺旋提升机;螺旋牙根挺•screw extractor断螺钉取出器;起螺丝器•screw extruder螺旋挤压机;螺旋压出机•screw extrusion machine蜗杆挤压机•screw extrusion press螺旋挤出机;螺旋挤压机•screw eye螺丝眼•screw eye(羊眼)羊眼圈•screw fan螺旋扇风机;轴流式扇风机•screw fastener螺钉扣•screw fastening螺钉连接;螺丝接合•screw feed螺旋喂送器•screw feed grease cup滑脂杯•screw feed mechanism螺旋加料机构•screw feeder螺杆给料机;螺旋加料器•screw fixing螺丝固定•screw flange栓接法兰•screw flange coupling螺钉凸缘联轴节•screw for alarm clock闹钟螺钉•screw for bearing wheel of oscillating weight自动锤轴承螺钉•screw for framework of automatic device自动框架螺钉•screw for indicator guard日历指示器护板螺钉•screw for jumper spring跳杆簧螺钉•screw for motor starter马达起动器螺钉•screw for setting lever spring压簧螺钉•screw for starter fixing clamp起动器固定夹螺钉•screw friction press螺旋摩擦压力机•screw ga(u)ge螺纹规•screw ga(u)ge(S.G.)螺纹量规•screw gauge for taper thread锥形螺纹量规•screw gear螺纹传动装置;螺旋齿轮;压下装置•screw gearing螺旋齿轮传动装置;蜗轮蜗杆传动装置•screw gill drawing frame螺旋杆式并条机•screw gun螺旋式油枪•screw head file螺钉头锉•screw height control螺杆式高度调节器•screw holder螺口灯头;螺丝夹持器•screw holding forceps持螺丝钳•screw home拧紧•screw hoop环首螺栓•screw horseporew推进器马力•screw housing clearance推运螺旋与壳间间隙•screw hub seal蜗杆毂密封•screw impeller螺旋叶轮•screw impeller pump螺旋桨式泵•screw jaw with lug带舌螺扣接杆•screw jaw with movable lug带活舌螺扣接杆•screw joint螺管接头;螺旋接合•screw key螺丝扳手;螺旋键•screw lid螺旋盖•screw lift螺旋提升机•screw lifting mechanism螺旋提升机构•screw lower bridge of automatic device自动装置下夹板螺钉•screw lubrication螺旋润滑•screw machine自动车床;制螺钉机•screw making machine制螺钉机•screw mandrel螺旋心轴;丝杆•screw micrometer螺杆测微计•screw micrometer cal(l)iper螺旋千分卡尺•screw microscope螺旋测微镜•screw mixer螺旋轴搅拌机•screw motor螺杆马达•screw nail螺丝钉;螺纹钉;木螺钉•screw nicking machine螺钉头开槽机•screw nut螺母•screw of tangential cutter head切向进刀架丝杠•screw off拧松•screw on拧上•screw pair丝杠螺母副;螺旋副•screw pile螺旋桩•screw pile foundation螺旋桩基•screw pin螺旋销•screw pin countersink shackle埋头螺丝卸扣•screw pinch螺旋箍缩•screw pitch螺纹距;螺旋节距•screw plasticating injection molding螺杆塑化式注塑•screw plate螺丝板牙;螺丝钢板;螺丝模;搓丝板;搓丝机;板牙•screw plow螺旋形犁•screw plug螺旋接线柱;螺旋塞•screw plug ga(u)ge螺纹塞规•screw press螺旋压机;螺旋压力机•screw prop千斤顶•screw propellor for boat船用螺旋桨推进器•screw pump螺杆泵;螺旋泵•screw punch螺旋冲压机•screw rack斜齿条•screw rail bender螺杆弯轨机•screw release螺旋式限时解锁器•screw remover去螺钉器•screw retention螺纹防松装置•screw reverse gear螺旋回动装置•screw ring环首螺钉•screw ring ga(u)ge螺纹环规•screw rivet螺纹铆钉;螺旋铆钉•screw riveting machine螺旋铆机•screw rod螺杆•screw rolling machine滚丝机•screw rule螺旋定则•screw shackle螺纹联接环;螺纹连接环•screw shaft螺杆轴;螺旋轴•screw shaft bushing螺旋轴衬套•screw shank螺钉杆•screw shaped mo(u)ldboard螺旋形犁壁•screw shaving machine制螺母及螺栓头机•screw sheel螺旋套筒;灯头螺口•screw shell螺旋套管•screw snap ga(u)ge螺纹卡规•screw socket螺丝灯头;螺丝套筒•screw spike螺丝钉;螺纹道钉;螺旋道钉•screw spindle螺旋轴•screw spreader螺旋传送器;螺旋分布器•screw stairs盘旋式楼梯•screw stem螺杆•screw stock螺旋扳手•screw stopper螺旋塞•screw stud双头螺栓•screw support for adjusting regulator调整快慢针的螺钉座•screw swinging mechanism螺旋摆动机构•screw tap丝锥•screw templet螺纹样板•screw terminal螺丝接线端•screw testing interferometer螺杆检验干涉仪;检验螺纹干涉仪•screw tight fitting紧配螺旋•screw tightener压紧螺钉•screw tip蜗杆梢•screw tourniquet螺旋止血带•screw tow bar螺旋式牵引杆•screw triad三重螺旋轴•screw tube罗纹管•screw type oil expeller螺旋榨油机•screw unit组合机床的动力头•screw up拧紧•screw value螺旋周值•screw valve螺旋球阀•screw vent螺杆通孔•screw ventilation螺旋桨式风机;螺旋通风器•screw vice螺旋虎钳•screw washer螺旋垫圈;螺旋洗矿机•screw wedge丝杆调节楔•screw willow螺旋威罗机•screw winder螺杆式络纱机•screw wiper螺旋式擦拭器•screw wire螺钉用钢丝•screw with diamond knurls金刚石滚花头螺钉•screw with flat head平头螺钉•screw with knurled head滚花头螺钉•screw with round head圆头螺钉•screw with straight-line直线滚花头螺钉•screw with straight-line knurls直线滚花头螺钉•screw without nut无帽螺钉•screw worm螺旋锥蝇幼虫•screw wrench螺钉扳手;活动扳手•screw-and-nut mechanism螺杆螺母传动机构•screw-and-nut steering gear螺杆螺母式转向器•screw-and-nut steering-gear螺杆螺母转向装置•screw-cap螺旋帽•screw-cutting lathe车螺纹车床•screw-cutting machine螺纹切削机床•screw-down压下机构•screw-driven螺旋传动•screw-driven planer螺杆传动刨床;丝杠式刨床•screw-driven planing machine螺杆传动刨床•screw-driven shaper螺杆传动牛头刨;丝杠式牛头刨床•screw-driven slotter丝杠式插床•screw-driver bit螺丝刀。
螺丝名称的中英文对照表
螺丝名称的中英文对照表The final revision was on November 23, 2020螺丝名称的中英文对照表常用英文单词及简写形式No. 单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread P T 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标47 ISO / 国际标准48 NFE / 法标49 GB / 国家标准50 Quality / 质量51 surface hardness 表面硬度52 product treatment 表面处理53 plating 电镀54 heat 热55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车用螺丝、轴心56 Screws And Shafts For Sewing Maching 针车用螺丝、轴心57 Socket Set Screws 止付螺丝58 Stainless Steel Coarse Thread Screws 不锈钢宽牙螺丝59 Stainless Steel High-Low Thread Screws 不锈钢高低牙螺丝60 Stainless Steel Machine Screws 不锈钢机械螺丝61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝62 Stainless Steel Self Tapping Screws 不锈钢螺丝 class=a1>自攻螺丝63 Stainless Steel Thread Cutting Screws 不锈钢自削螺丝64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三角牙螺丝65 Steel Ceiling Anchors 插片壁虎66 Drop in Anchors 内迫壁虎67 Steel Hit Anchors 碳钢锤钉壁虎68 Steel Hex Coupling Nuts 碳钢六角螺帽69 Wedge Anchors 强力车修壁虎70 Cut Anchors 外迫壁虎71 Chemical Anchors 化学壁虎72 Heavy Duty Expansion Anchors 不锈钢重载胀栓73 Tie Wire Anchors 鱼眼壁虎?企眼长螺帽74 Hammer Drive Anchors 锌合金打入式壁虎75 Strut Nuts 弹簧螺帽?76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列77Nylon Frame Anchors or Metalframe Anchors 门窗、地板专用壁虎78 Hollow Wall Anchors 石膏板中空壁虎79 Sleeve Anchors 套管式壁虎80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打入式壁虎鱼形尼龙壁虎81 Hit Anchors 强力式锤钉壁虎82 Bolt Anchors 电梯壁虎83 Heavy duty anchors 重载壁虎84 Loxin Masonry Anchors 两片夹85 Set Bolts 定位螺栓86 Short Strap Anchors 长型兰花夹87 Drop in Setting Tools 工具棒88 Elephant foot anchors 象脚壁虎89 Concrete Insert 水泥预埋件90 Drop in Anchor with Lip 翻边胀轴91 Legs Drywall Anchors 冲件92 Hex Cap Nuts 六角盖头螺帽93 Hex Serrated Nuts 六角锯齿螺帽?94 Hex Flange Nuts 六角轮缘螺帽?95 Hex Coupling Nuts(High Nuts) 高脚螺帽96 Round Nuts 圆螺帽97 Square Nuts 四角螺帽98 Pipe Nuts 管用螺帽99 Wheel Nuts 轮壳螺帽100 Wing Nuts 蝶型螺帽101 U Nuts U形螺帽?102 T Nuts T形螺帽103 Eye Nuts 环首螺帽104 Kep Nuts 齿形螺帽?105 Clinch Nuts 齿花螺帽106 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽107 Weld Nuts 焊接螺帽108 Heigh Strength Nuts 高张力螺帽109 Structural Nuts 建业用螺帽110 Stainless Steel Nuts 不锈钢螺帽111 Brass Nuts 铜螺帽112 Aluminum Nuts 铝螺帽113 Alloy Steel Nuts 合金钢螺帽114 Heavy Duty Wheel Hub Nuts 重型车螺帽115 Acorn Cap Nuts 铁器焊接袋帽116 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽117 Anchor Nuts 壁虎螺帽118 Big Size Nuts 大尺寸螺帽119 Closed End Acorn Nuts 铁盖袋帽120 Conical Washer Nuts 盘形华司螺帽121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽123 Flat Waser Nuts 平面华司螺帽124 Hex Slotted Nut 六角割沟螺帽125 Self-Locking Nuts 自锁螺帽126 Sliding Nuts 制止螺帽127 Sln Self-Locking Nuts Sln-自动防松螺帽128 Special Nuts 其它特殊螺帽129 Spring Nuts 弹簧螺帽130 Stainless Steel Flange Nuts 不锈钢突缘螺帽131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽132 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽133 Stainless Steel Hex Nuts 不锈钢六角螺帽134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽135 Hex Nuts 普通六角螺帽136 Heavy Hex Nuts 六角重型螺帽137 Hex Jam Nuts 薄型螺帽138 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽139 Hex Machine Screw Nut 机械螺丝用六角螺帽140 Hex Head Cap Screws(Hex Bolts) 六角螺丝(栓)141 Hex Head Machine Bolts 六角机械螺丝142 Hex Lag Bolts 六角木牙螺丝143 Square Head Bolts 四角螺丝144 Carriage Bolts 马车。
螺丝各种中英对照
中文名稱英文名稱六角螺絲(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角機械螺絲HEX HEAD MACHINE BOLTS六角木牙螺絲HEX LAG BOLTS四角螺絲SQUARE HEAD BOLTST頭螺絲T HEAD BOLTS馬車螺絲CARRIAGE BOLTS環首螺絲EYE BOLTS內六角孔螺絲HEX SOCKET CAP SCREWS固定螺絲SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS輪殼螺栓WHEEL BOLTS翼形螺絲WING SCREWS自攻螺絲SELF TAPPING SCREWS自削螺絲THREAD CUTTING SCREWS鑽尾螺絲SELF DRILLING SCREWS旋入螺絲DRIVE SCREWS機械螺絲MACHINE SCREWS木螺絲WOOD SCREWS家具螺絲FURNITURE SCREWS塑板螺絲CHIPBOARD SCREWS牆用螺絲DRYW ALL SCREWS基礎螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾頭螺栓HOOK BOLTS套掛螺絲TOGGLE BOLTS突緣螺絲FLANGE BOLTS軌道螺栓(魚尾螺絲) TRACK BOLTS耐候鋼螺絲CORTEN STEEL HEA VY HEX BOLTS扭矩控制螺栓T.C.BOLTS高張力螺栓HIGH STRENGTH BOLTS剪力釘(焊接螺絲) WELDING STUDS螺絲附華司組合SCREWS AND W ASHERS ASSEMBLED(SEMS) 大尺寸螺栓BIG SIZE BOLTS不鏽鋼小螺絲STAINLESS STEEL SHEET METAL SCREWS不鏽鋼大螺絲STAINLESS STEEL BOLTS銅螺絲BRASS SCREWS鋁螺絲ALUMINUM SCREWS合金鋼螺絲ALLOY STEEL SCREWS電子螺絲ELECTRONIC SCREWS微小精密螺絲MICRO SCREWS塑膠螺絲PLASTIC SCREWS復合材料用螺絲PARTICLE BOARD SCREWS鈦合金螺絲TITANIUM ALLOY BOLTS鈦、鋯、鉬、鈮等螺絲、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺絲THUMB SCREWS雙頭牙螺絲DOUBLE END SCREWS HANGER BOLT車輛(汽車)螺絲、螺帽AUTOMOTIVE FASTENERS航太用螺絲AEROSPACE FASTENERS飛機特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺絲PANEL FASTENERS電梯螺絲ELEVATOR BOLTS四角頭固定螺絲SQUARE SET SCREWS大頭馬車螺絲STEP BOLTS單向螺絲ONE W AY LAG SCREWS管夾螺絲HOSE CLAMP SCREWS不鏽鋼固定螺絲STAINLESS STEEL HEX SOCKET CAP SCREWS不鏽鋼內六角螺絲STAINLESS STEEL HEX SOCKET CAP SCREWS鉸鏈螺絲HINGE SCREWS貨櫃螺絲CONTAINER SCREWS復合材料鑽尾螺絲BI-METAL SELF DRILLING SCREWS三角牙螺絲TRILOBULAR THREAD SCREWS高低牙螺絲HIGH LOW SCREWS夾板用螺絲PARTICLE BOARD SCREWS馬桶螺絲TOILET CLOSET BOLTS特長螺絲SPECIAL LONGER SCREWS建業螺絲BUILDING FASTENERS不鏽鋼六角螺絲STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺絲SPECIAL SCREWS OR BOLTS不鏽鋼特殊螺絲SPECIAL STAINLESS STEEL SCREWS寬牙螺絲（粗牙螺絲）COARSE THREAD SCREWS鏈帶螺絲COLLATED SCREWS水泥螺絲CONCRETE SCREWS板模螺絲CONSTRUCTION BOLTS鋅蝶螺絲DIE CAST WING SCREWS; ZINC ALLOY重型車螺絲HEA VY DUTY WHEEL HUB BOLTS內六角固定螺絲HEX SOCKET SET SCREWS復合材料用螺絲（夾板用）PARTICLE BOARD SCREWS犁壁螺絲PLOW BOLTS機(踏)車用螺絲、軸心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 針車用螺絲、軸心SCREWS AND SHAFTS FOR SEWING MACHING止付螺絲SOCKET SET SCREWS不鏽鋼寬牙螺絲STAINLESS STEEL COARSE THREAD SCREWS不鏽鋼高低牙螺絲STAINLESS STEEL HIGH-LOW THREAD SCREWS不鏽鋼機械螺絲STAINLESS STEEL MACHINE SCREWS不鏽鋼鑽尾螺絲STAINLESS STEEL SELF DRILLING SCREWS不鏽鋼自攻螺絲STAINLESS STEEL SELF TAPPING SCREWS不銹鋼自削螺絲STAINLESS STEEL THREAD CUTTING SCREWS不鏽鋼三角牙螺絲STAINLESS STEEL TRI-LOBULAR THREAD SCREWS不鏽鋼木螺絲STAINLESS STEEL WOOD SCREWS套掛螺栓及螺絲TOGGLE BOLTS鈦合金膨脹螺絲TITANIUM ALLOY EXPANSION BOLTS中文名稱英文名稱六角蓋頭螺帽HEX CAP NUTS六角鋸齒螺帽HEX SERRATED NUTS六角輪緣螺帽HEX FLANGE NUTS高腳螺帽HEX COUPLING NUTS(HIGH NUTS)圓螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS輪殼螺帽WHEEL NUTS蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽T NUTS環首螺帽EYE NUTS齒形螺帽KEP NUTS齒花螺帽CLINCH NUTS耐候鋼六角重型螺帽CORTEN STEEL HEA VY HEX NUTS焊接螺帽WELD NUTS高張力螺帽HEIGH STRENGTH NUTS建業用螺帽STRUCTURAL NUTS不鏽鋼螺帽STAINLESS STEEL NUTS銅螺帽BRASS NUTS鋁螺帽ALUMINUM NUTS合金鋼螺帽ALLOY STEEL NUTS重型車螺帽HEA VY DUTY WHEEL HUB NUTS鐵器焊接袋帽ACORN CAP NUTS金屬預置扭矩式螺帽ALL-METAL PREV AILING TORQUE TYPE NUTS 壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS鐵蓋袋帽CLOSED END ACORN NUTS盤形華司螺帽CONICAL WASHER NUTS鐵蓋+尼龍圈組合蓋帽DIN 986 DOMED CAP NUTS突緣尼龍蓋帽FLANGE NYLON INSERT LOCK NUTS平面華司螺帽FLAT WASER NUTS六角割溝螺帽HEX SLOTTED NUT自鎖螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自動防鬆螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS彈簧螺帽SPRING NUTS不鏽鋼突緣螺帽STAINLESS STEEL FLANGE NUTS不鏽鋼六角輪緣尼龍螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS 不鏽鋼六角重型螺帽STAINLESS STEEL HEA VY HEX NUTS不鏽鋼六角螺帽STAINLESS STEEL HEX NUTS不鏽鋼尼龍嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS鋅壓屬螺帽ZINC DIE CASTING NUTS普通六角螺帽HEX NUTS六角重型螺帽HEA VY HEX NUTS薄型螺帽HEX JAM NUTS尼龍嵌入防鬆螺帽NYLON INSERT LOCK NUTS機械螺絲用六角螺帽HEX MACHINE SCREW NUT中文名稱英文名稱合金鋼線材盤元ALLOY STEEL WIRE ROD球狀化線材ANNEALING WIRE AND ROD黑鐵絲BLACK WIRE黃銅棒線BRASS WIRE AND ROD磨光棒鋼BRIGHT STEEL BAR(HEX/ROUND/SQUARE)銅合金線COPPER ALLOY WIRE線切割線E.D.M CUTTING WIRE快削鋼線材盤元FREE CUTTING STEEL WIRE ROD線材IRON OR STEEL WIRE線材盤元IRON OR STEEL WIRE ROD洋白銅線NICKEL SILVER WIRE磷青銅線PHOSPHA TE BRONZE WIRE不鏽鋼條棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不鏽鋼冷鍛線材STAINLESS STEEL COLD HEADING WIRE不鏽鋼線(抽線後) STAINLESS STEEL DRAW WIRE不鏽鋼線材STAINLESS STEEL WIRE不鏽鋼線材及盤元STAINLESS STEEL WIRE AND ROD棒鋼STEEL BAR(HEX/ROUND/SQUARE)轉回90度碾線頭機90訌EVOLVING WIRE TWISTING MACHINE氣動拉釘機AIR RIVETER各式螺絲類產品自動包裝AUTOMA TIC PACKAGING FOR ALL KINDS OF PACKAGING 自動包裝機AUTOMA TIC PACKING MACHINE螺絲製造搓牙機械AUTOMATIC THREAD ROLLING MACHINE螺絲割尾加工機械AUTOMATIC THREAD SLOTTING MACHINE螺絲製造成型機械AUTOMATIC TRIMMING MACHINE拉釘打頭機BLIND RIVET HEADING MACHINE螺絲、螺帽成型機BOLT FORMERS,NUTS FORMERS,HEADERS螺絲、螺帽熱處理BOLT NUT AND SCREWS HEAT TREATMENT螺絲、螺帽熱處理爐BOLT NUT AND SCREWS HEAT TREATMENT FURNACES球狀化電器燉爐CARBURIZING FURNACE V ACUUM AND BELL TYPE FURNACE超防銹復合瓷膜CERAMIC COATING連續式光輝滲碳淬火爐CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE 連續式光輝調質淬火爐CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中、高熱鍍鋅光輝連續爐CONTINUOUS BRIGHT HEAT TREAT FURNACE連續式光輝熱處理爐CONTINUOUS TYPE BRIGHT HEAT TREATMENT FURNACE螺絲割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING螺絲鑽孔加工SCREW SHANK DRILLING雞眼上下模EYELETS DIES一般線材、盤元、退火爐GENERAL WIRE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸線機HANDSTAND TYPE WIRE DRAWING MACHINE十字沖模HEADER PUNCHES IN V ARIOUS DRIVES成型沖模HEADER PUNCHES IN V ARIOUS DRIVES螺絲打頭機HEADING MACHINE螺絲製造高速搓牙機械HIGH SPEED AUTOMA TIC THREAD ROLLING MACHINE高中低周波感應加熱爐HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEATER空心打頭機HOLLOW HEADING MACHINE熱浸鍍鋅螺絲、螺帽HOT DIP GALV ANIZING BOLTS AND NUTS機械鍍鋅MECHANICAL GALV ANIZED迷你成型機MINI-FORMERS成品自動收線機NON-STOP COILER精抽自動收線機NON-STOP COILER(SKINPASS)螺帽模NUT FORMING DIES螺帽成型模NUTS FORMERS特殊零件成型機PARTS FORMING MACHING沖模PUNCH DIES沖子PUNCH PINS羅拉成型機ROLLERS FORMERS機(踏)車用螺絲成型機SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE 止付螺絲成型機SET SCREWS FORMERS套高成型機SOCKETS FORMERS一般線材、盤元、螺絲合金燉爐SPHEROIDIZING BRIGHT ANNEALING FURNACE球狀化熱處理爐SPHEROIDIZING HEAT TREATMENT FURNACE攻牙機TAPPING MACHINE螺絲攻、車刀、模具TAPS DIES AND TOOLS搓牙機鐵屑分離裝置THREAD CHIP SEPARA TOR滾牙輪THREAD ROLLING DIES牙板THREAD ROLLING DIES PLATES精密油壓滾牙機HYDRAULIC THREAD ROLLING MACHINES模具TOOLS六角整頭模TRIMMING DIES HEXAGAN碳化鎢模具TUNGSTEN CARBIDE DIE鍍鈦處理(TiN)專業加工服務TiN HARD COATING FOR CUTTING TOOLS AND PUNCH BY PVD電鍍化學原料V ARIOUS ELECTROPLATING CHEMICALS環規校正CALIBRATION FOR RING GAGE環規、牙規、三線規校正CALIBRATION FOR RING GAGE, ATHREAD GAGE, 3 WIRE GAGE螺絲、螺帽品檢量測儀器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS螺絲、螺帽成型攻牙專用油FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS螺絲、螺帽五金等檢驗INSPTECTION SERVICES FOR FASTENERS AND HARDWARE 德國SCHATZ扭力機代理REPRESENTATIVE OF SCHATZ TORQUE MACHINISO品質保證系統ISO QUALITY ASSURANCE SYSTEM生產管理系統PRODUCTION CONTROL SYSTEM物料管理系統MATERIAL CONTROL SYSTEM中文名稱英文名稱齒輪GEARS不銹鋼牙條棒STAINLESS STEEL HREAD ROD馬達軸承軸心組件BEARING SHAFT(MOTOR)軸承軸心BEARING SHAFT開口鉚釘BLIND RIVETS長形拉帽BLIND RIVET NUTS拉帽BLIND NUTS拉釘BLIND RIVETS實心梢CLEVIS PINS AND STRAIGHT PINS彈片CLIPS卷釘COIL NAILS冷鍛零件COLD FORMING PART開口銷COTTER PINSE型環E-RINGS膨脹螺栓EXPANSION ANCHOR BOLTS雞眼釘EYELETS RIVETSR型銷SNAP PINS閘、鎖LATCHES AND KEEPER ASSEMBLEDS其它特殊鉚釘OTHER SPECIL RIVETS銷PINS格式管夾、管束PIPE HANGER鉚釘RIVETS螺旋鋦及螺旋圈SCREW HOOK AND SCREW RINGS中空釘SEMI-TUBULAR RIVET開叉釘SPLIT DRIVE ANCHORS彈簧華司SPRING W ASHERS彈簧蝴蝶夾SPRING WINGS不銹鋼華司STAINLESSSTEEL WASHERS鋼鐵釘STEEL AND IRON NAILS搓牙鐵釘THREAD NAILS鈦合金鉚釘TITAIUM ALLOY RIVETS管形鉚釘TUBULAR RIVETS華司W ASHERS真空熱處理V ACUUM HEAT TREATMENT螺絲、螺帽、五金、DIY扣件FASTENERS合金鋼工具ALLOY STEEL TOOLS螺栓模BOLT HEADING DIES手動拉釘鉗HAND RIVETER船舶鏈ANCHOR CHAIN腳踏車鏈鎖BICYCLE CHAIN LOCKS螺絲起子BIT羅拉CHAIN ROLLER特殊鉚合扣件COLLARS(A BLINDFASTENER FOR HUCK INTL)裝飾鏈DECORATIVE CHAINS自攻螺紋襯套ENSAT THREADED INSERTS六角扳手HEXAGON KEYS超音螺紋壓入式螺紋自動鎖扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS汽車特殊桿接件SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS螺紋護套RECOIL INSERTS鏈條用滾子ROLLER FOR ROLLER CHAIN金屬板鑲嵌組件及自動夾扣組件SHEET METAL FASTENERS工具套筒組件SOCKET WRENCH SETS不銹鋼鏈STAINLESS STEEL CHAINS軛子T-YOKE輪胎鏈TIRE CHAINS狗鏈DOG CHAINS喇叭頭軛鐵U-YOKE,T-YOKE FOR SPEAKER不銹鋼輸送帶輪用軌道STAINLESS WHEEL'S RACK FOR TRANSPORTER工業用鏈INDUSTRIAL STEEL LINK CHAINS拖鏈安全鏈TOW CHAINS AND SAFETY CHAINS機車離合器零件MANUFACTURE OF MOTORCYCLE'S CVT PARTS牙條棒THREAD ROD。
中英文对照 螺丝
以下中英文对照可作为外销定单时的参考：六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS鑽尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS牆用螺丝DRYWALL SCREWS基础螺栓FOUNDA TION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝CORTEN STEEL HEA VY HEX BOLTS扭矩控制螺栓T.C.BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓BIG SIZE BOLTS不鏽钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不鏽钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑胶螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS航太用螺丝AEROSPACE FASTENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FASTENERS电梯螺丝ELEV A TOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE W AY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不鏽钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不鏽钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料鑽尾螺丝BI-METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS不鏽钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝SPECIAL SCREWS OR BOLTS不鏽钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLA TED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS锌蝶螺丝DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEA VY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不鏽钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不鏽钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不鏽钢机械螺丝STAINLESS STEEL MACHINE SCREWS不鏽钢鑽尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不鏽钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不鏽钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不鏽钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRA TED NUTS六角轮缘螺帽HEX FLANGE NUTS高脚螺帽HEX COUPLING NUTS(HIGH NUTS)圆螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS轮壳螺帽WHEEL NUTS蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽T NUTS环首螺帽EYE NUTS齿形螺帽KEP NUTS齿花螺帽CLINCH NUTS耐候钢六角重型螺帽CORTEN STEEL HEA VY HEX NUTS焊接螺帽WELD NUTS高张力螺帽HEIGH STRENGTH NUTS建业用螺帽STRUCTURAL NUTS不鏽钢螺帽STAINLESS STEEL NUTS铜螺帽BRASS NUTS铝螺帽ALUMINUM NUTS合金钢螺帽ALLOY STEEL NUTS重型车螺帽HEA VY DUTY WHEEL HUB NUTS铁器焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREV AILING TORQUE TYPE NUTS壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司螺帽CONICAL WASHER NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS突缘尼龙盖帽FLANGE NYLON INSERT LOCK NUTS平面华司螺帽FLA T W ASER NUTS六角割沟螺帽HEX SLOTTED NUT自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自动防鬆螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS弹簧螺帽SPRING NUTS不鏽钢突缘螺帽STAINLESS STEEL FLANGE NUTS不鏽钢六角轮缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS不鏽钢六角重型螺帽STAINLESS STEEL HEA VY HEX NUTS不鏽钢六角螺帽STAINLESS STEEL HEX NUTS不鏽钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS锌压属螺帽ZINC DIE CASTING NUTS普通六角螺帽HEX NUTS六角重型螺帽HEA VY HEX NUTS薄型螺帽HEX JAM NUTS尼龙嵌入防鬆螺帽NYLON INSERT LOCK NUTS机械螺丝用六角螺帽HEX MACHINE SCREW NUT合金钢线材盘元ALLOY STEEL WIRE ROD球状化线材ANNEALING WIRE AND ROD黑铁丝BLACK WIRE黄铜棒线BRASS WIRE AND ROD磨光棒钢BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线 E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHA TE BRONZE WIRE不鏽钢条棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不鏽钢冷锻线材STAINLESS STEEL COLD HEADING WIRE不鏽钢线(抽线后) STAINLESS STEEL DRA W WIRE不鏽钢线材STAINLESS STEEL WIRE不鏽钢线材及盘元STAINLESS STEEL WIRE AND ROD棒钢STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机90讧EVOLVING WIRE TWISTING MACHINE气动拉钉机AIR RIVETER各式螺丝类产品自动包装AUTOMA TIC PACKAGING FOR ALL KINDS OF PACKAGING 自动包装机AUTOMA TIC PACKING MACHINE螺丝製造搓牙机械AUTOMA TIC THREAD ROLLING MACHINE螺丝割尾加工机械AUTOMA TIC THREAD SLOTTING MACHINE螺丝製造成型机械AUTOMA TIC TRIMMING MACHINE拉钉打头机BLIND RIVET HEADING MACHINE螺丝、螺帽成型机BOLT FORMERS,NUTS FORMERS,HEADERS螺丝、螺帽热处理BOLT NUT AND SCREWS HEA T TREA TMENT螺丝、螺帽热处理炉BOLT NUT AND SCREWS HEA T TREA TMENT FURNACES球状化电器炖炉CARBURIZING FURNACE V ACUUM AND BELL TYPE FURNACE超防锈复合瓷膜CERAMIC COA TING连续式光辉渗碳淬火炉CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE 连续式光辉?#123;质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE中、高热镀锌光辉连续炉CONTINUOUS BRIGHT HEA T TREA T FURNACE连续式光辉热处理炉CONTINUOUS TYPE BRIGHT HEA T TREA TMENT FURNACE螺丝割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING螺丝鑽孔加工SCREW SHANK DRILLING鸡眼上下模EYELETS DIES一般线材、盘元、退火炉GENERAL WIRE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE十字冲模HEADER PUNCHES IN V ARIOUS DRIVES成型冲模HEADER PUNCHES IN V ARIOUS DRIVES螺丝打头机HEADING MACHINE螺丝製造高速搓牙机械HIGH SPEED AUTOMA TIC THREAD ROLLING MACHINE高中低周波感应加热炉HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEA TER空心打头机HOLLOW HEADING MACHINE热浸镀锌螺丝、螺帽HOT DIP GALV ANIZING BOLTS AND NUTS机械镀锌MECHANICAL GALV ANIZED迷你成型机MINI-FORMERS成品自动收线机NON-STOP COILER精抽自动收线机NON-STOP COILER(SKINPASS)螺帽模NUT FORMING DIES螺帽成型模NUTS FORMERS特殊零件成型机PARTS FORMING MACHING冲模PUNCH DIES冲子PUNCH PINS罗拉成型机ROLLERS FORMERS机(踏)车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE 止付螺丝成型机SET SCREWS FORMERS套高成型机SOCKETS FORMERS一般线材、盘元、螺丝合金炖炉SPHEROIDIZING BRIGHT ANNEALING FURNACE球状化热处理炉SPHEROIDIZING HEA T TREA TMENT FURNACE攻牙机TAPPING MACHINE螺丝攻、车刀、模具TAPS DIES AND TOOLS搓牙机铁屑分离装置THREAD CHIP SEPARA TOR滚牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLA TES精密油压滚牙机HYDRAULIC THREAD ROLLING MACHINES模具TOOLS六角整头模TRIMMING DIES HEXAGAN碳化钨模具TUNGSTEN CARBIDE DIE镀钛处理(TiN)专业加工服务TiN HARD COA TING FOR CUTTING TOOLS AND PUNCH BY PVD电镀化学原料V ARIOUS ELECTROPLA TING CHEMICALS环规校正CALIBRA TION FOR RING GAGE环规、牙规、三线规校正CALIBRA TION FOR RING GAGE, A THREAD GAGE, 3 WIRE GAGE螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENTINSTRUMENTS螺丝、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTSFORMERS螺丝、螺帽五金等检验INSPTECTION SERVICES FOR FASTENERS AND HARDWARE ISO品质保证系统ISO QUALITY ASSURANCE SYSTEM生产管理系统PRODUCTION CONTROL SYSTEM物料管理系统MA TERIAL CONTROL SYSTEM。
螺丝名词中英文对照
螺丝名词中英文对照摘要：螺丝名词中英文对照No. 单词简写中文 1 screw scr 螺丝 2 nut nut ... 螺丝名词中英文对照No.单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial P T 半螺纹thread17 PT PT 一种螺纹形式18 Full FT 全螺纹Thread19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread TF 自攻螺纹Forming23 Self self tapp 自切屑螺纹Tapping24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless SS 不锈钢steel28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine mech scr 机制螺丝screw32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标紧固件类英语词汇白铁盖螺丝A2(18-8)CAP SCREWS水平调整螺丝ADJUSTED LEVELING SCREWS航太扣件AEROSPACE FASTENERS合金钢螺丝(栓) ALLOY STEEL SCREWS (BOLTS)铝螺丝ALUMINUM SCREWS车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS复含材料钻尾螺丝BI-METAL SELF DRILLING SCREWS 大尺寸螺丝BIG SIZE BOLTS公母螺丝组BINDER POST & SCREW SET拉栓BLIND BOLTS铜螺丝(栓) BRASS SCREWS (BOLTS)建筑螺丝BUILDING FASTENERS建筑膨涨螺丝BUILDING WALL ANCHOR半圆头六角孔螺丝BUTTON HEAD SOCKET CAP SCREWS 马车螺丝CARRIAGE BOLTS活动轮螺丝附件CASTORS FITTINGS塑板螺丝CHIPBOARD SCREWS快速钉紧螺丝及螺帽CLINCH STUDS & NUTS挤压扣件CLINCHING FASTENERS齿花扣件CLINCHING PARTS宽牙螺丝COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模扣件CONSTRUCTION FASTENERS货柜螺丝CONTAINER SCREWS耐候钢螺丝CONTEN STEEL HEAVY HEX BOLTS鱼尾螺丝CONTEN STEEL OVAL NECK TRACK BOLTS双刀螺丝CUTTER SCREWS匣板螺丝DECK SCREWS锌蝶螺丝DIE CAST WING SCREWS;ZINC ALLOY双头牙螺丝DOUBLE END SCREWS，HANGER BOLT旋锁螺丝DRIVE LOCK SCREWS旋入螺丝DRIVE SCREWS墙用螺丝DRYWALL SCREWSEJOT DELTA PT SCREWSEJOT PT SCREWS电子螺丝ELECTRONIC SCREWS电梯螺丝ELEVATOR BOLTS欧洲螺丝EURO SCREWS环首螺丝EYE BOLTS冈山头螺丝FILLISTER SCREWS鳍头螺丝FIN NECK ROUND HEAD BOLTS管配件接头FITTING FASTENERS (CONNECTORS)突缘螺丝FLANGE BOLTS (SCREWS)平头六角孔螺丝FLAT HEAD SOCKET CAP SCREWS平纺螺丝FLAT PAN HEAD SCREWS地板螺丝FLOORING PANEL SCREWS基础螺丝FOUNDATION BOLTS框架支撑螺丝FRame ANCHOR-LAG ROUND SCREWS家俱螺丝FURNITURE SCREWS (CONNECTING BOLTS)重型车螺丝、螺帽HEAVY DUTY WHEEL HUB BOLTS & NUTS 六角螺丝(栓) HEX HEAD CAP SCREWS (HEX BOLTS)六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS等高螺丝HEX SOCKET HEAD SHOULDER SCREW薄头强力螺丝HEX SOCKET LOW HEAD CAP SCREW内六角固定螺丝HEX SOCKET SET SCREWS华司头机械螺丝HEX WASHER HEAD MACHINE SCREWS高低牙螺丝HIGH LOW THREAD SCREWS高张力螺丝HEX SOCKET HEAD SHOULDER SCREW铰链螺丝HINGE SCREWS勾头螺栓HOOK BOLTS管夹螺丝HOSE CLAMP SCREWS哈克钉HUCK BOLTS旋锁螺丝KTX LOCKING RECESS SCREWS机械螺丝MACHINE SCREWSMDF螺丝MDF SCREWS微小精密螺丝MICRO SCREWS钼六角螺丝MO HEX HEAD CAP SCREWS钼NC螺丝MO NC FASTENERS钼螺帽MO NUTS镍合金螺丝MONEL FASTENERS多冲程螺丝MULTI-STAGE SCREW & PARTS利革钉NYLON PLUG & SCREWS单向螺丝ONE WAY LAG SCREWS枋头中心螺丝PAN HEAD CENTER BOLTS面板螺丝PANEL FASTENERS复合材料用螺丝(夹板用) PARTICLE BOARD SCREWS贯穿螺丝PENETRATE SCREWS十字四角复合螺丝PH+SQ COMBINATION SCREWS塑胶螺丝PLASTIC SCREWS犁壁螺丝PLOW BOLTS特殊精密螺丝PRECISION AXIS AND SPECIAL FASTENERS卷带螺丝ROLL COLLATED SCREWS屋顶螺丝ROOFING SCREWS螺旋椿SCREW STUDS机(踏)车用螺丝.轴心SCREWS & SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝.轴心SCREWS & SHAFTS FOR SEWING MACHINE螺丝附华司组合SCREWS & WASHERS ASSEMBLED (SEMS)安全螺丝SECURITY SCREWS钻尾螺丝SELF DRILLING SCREWS自攻螺丝SELF TAPPING SCREWS固定螺丝SCREWS & SHAFTS FOR SEWING MACHINE剪力钉SHEAR CONCRETE STUD束肩螺丝(栓) SHOULDER SCREWS (BOLTS)一字沟槽固定螺丝SLOTTED SET SCREWS止付螺丝SOCKET SET SCREWS飞机特殊扣件SOURCE CONTROL BOLTS特殊涂装螺丝SPECIAL COATING SCREWS特长螺丝SPECIAL LONGER SCREWS特殊材质螺丝SPECIAL MATERIAL SCREWS特殊螺丝SPECIAL SCREWS OR BOLTS特殊防松螺丝SPECIAL SELF-LOCKING SCREWS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS特殊割尾螺丝SPECIAL THREAD CUTTING SCREWS四角螺丝SQUARE HEAD BOLTS四角头固定螺丝SQUARE HEAD SET SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS不锈钢塑板螺丝STAINLESS STEEL CHIPBOARD SCREWS不锈钢粗牙螺丝STAINLESS STEEL COARSE THREAD SCREWS 不锈钢旋入螺丝STAINLESS STEEL DRIVE SCREWS不锈钢平头内六角孔螺丝STAINLESS STEEL FLAT HEAD SOCKET CAP SCREWS 不锈钢六角螺丝STAINLESS STEEL HEX HEAD CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET SET SCREWS 不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREADSCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢小螺丝STAINLESS STEEL SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢SEMS 螺丝STAINLESS STEEL SEMS SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS 不锈钢牙条棒STAINLESS STEEL THREAD ROD不锈钢三角牙螺丝STAINLESS STEEL TRIANGULAR SCREW THREAD不锈钢木螺丝STAINLESS STEEL WOOD SCREWS卡锁壁虎STEEL LOCKING ANCHOR大头马车螺丝STEP BOLTS螺桩栓STUD BOLTST头螺丝T HEAD BOLTS扭矩控制螺栓T.C. BOLTS (TENSION CONTROL BOLTS)自削螺丝THREAD CUTTING SCREWS牙条棒THREAD ROD姆指螺丝THUMB SCREWS钛合金自行车螺丝TITANIUM -6AL –4R ALLOY FASTENERS钛合金螺丝TITANIUM ALLOY BOLTS钛六角螺丝TITANIUM HEX HEAD CAP SCREWS (HEX BOLTS) 钛NC螺丝TITANIUM NC FASTENERS钛止付螺丝TITANIUM SET SCREWS钛内六角孔螺丝TITANIUM SOCKET CAP SCREWS钛牙条TITANIUM THREAD ROD套挂螺丝TOGGLE BOLTS套挂螺栓及螺丝TOGGLE BOLTS & ACOUSTICAL LAG (SCREWEYE) 马桶螺丝TOILET CLOSET BOLTSTORX SCREWS TORX SCREWS轨道螺栓(鱼尾螺丝) TRACK BOLTS三角牙螺丝TRIANGULAR SCREWS THREADU型螺栓U BOLTS直立轴螺丝VERTICAL SHAFT SCREWS焊接螺丝WELD STUDS，SCREWS，BOLTS焊点螺丝WELD STUDS SCREWS轮毂螺栓WHEEL BOLTS车轮轴螺丝，螺帽WHEEL HUB BOLTS AND NUTS窗户螺丝WINDOW SCREWS翼形螺丝WING SCREWS木螺丝WOOD SCREWS锆螺丝ZR FASTENERSSET SCREWS SET SCREWSHIGH STRENGTH BOLTS HIGH STRENGTH BOLTS铁盖焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREVAILING TORQUE TYPE NUTS 合金钢螺帽ALLOY STEEL NUTS铝螺帽ALUMINUM NUTS壁虎螺帽ANCHOR NUTS圆柱帽BARREL NUTS (CROSS DOWEL)大尺寸螺帽BIG SIZE NUTS铜螺帽BRASS NUTS四角多用途螺帽CAGE NUTS袋帽CAP NUTS城堡螺帽CASTLE NUTS齿花螺帽CLINCH NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司+袋帽螺帽CONICAL WASHER AND CAP NUTS盘形华司螺帽CONICAL WASHER NUTS耐候钢六角重型螺帽CORTEN STEEL HEAVY HEX NUTS长螺帽COUPLING NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS碟锁防松脱螺帽DISK-LOCK NUTS企眼螺帽EYE COUPLING NUTS环首螺帽EYE NUTS突缘尼龙螺帽FLANGE NYLON INSERT LOCK NUTS平面华司螺帽FLAT WASHER NUTS齿轮GEARS六角重型螺帽HEAVY HEX NUTS六角盖头螺帽HEX CAP NUTS六角突缘螺帽HEX FLANGE NUTS薄型螺帽HEX JAM NUTS薄型电子六角螺帽HEX JAM NUTS (FOR ELECTRONIC) 机械螺丝用六角螺帽HEX MACHINE SCREW NUT普通六角螺帽HEX NUTS六角锯齿螺帽HEX SERRATED NUTS双头内牙螺帽HEX (REDUCER )COUPLING NUTS高螺帽HIGH NUTS高张力螺帽HIGH STRENGTH NUTS内外牙螺母(拉帽) INSERT NUTSJCN NUTS JCN NUTS齿形螺帽KEP NUTS防松螺帽LOCK NUTS长螺帽LONG NUTS机车用螺帽NUTS FOR MOTORCYCLE面板螺帽NUTS PLATE尼龙袋帽NYLON CAP INSERT LOCK NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS马桶螺帽OPEN END ACORN NUTS卡车轮胎螺帽OUTER CAP NUTS管用螺帽PIPE NUTS塑胶螺帽PLASTIC NUTSPOP NUTS POP NUTS抑制螺帽PREVAILING TORGUE NUT快速扣件PUSH NUT FASTENERS长方形螺帽(薄型) RECTANGLE JAM NUTS长方四角螺帽RECTANGLE SQUARE NUTS圆螺帽ROUND NUTS自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自锁防松螺帽SLN SELF-LOCKING NUTS沟槽螺帽SLOTTED NUTS特殊螺帽SPECIAL NUTS特殊轮毂螺帽SPECIAL WHEEL NUTS弹簧螺帽SPRING NUTS薄型四角螺帽SQUARE JAM NUTS四角螺帽SQUARE NUTS不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角突缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS 不锈钢六角重型螺帽STAINLESS STEEL HEAVY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢螺帽STAINLESS STEEL NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS不锈钢四角螺帽STAINLESS STEEL SQUARE NUTS建筑用螺帽STRUCTURAL NUTST形螺帽T NUTS塑胶品之埋植铜，铝螺帽THREADED INSERTS FOR PLASTIC INJECTION MOULDINGS钛螺帽TITANIUM NUTS压边螺帽+盘形华司组合TOP LOCK NUT WITH CONICAL WASHER ASSEMBLEU形螺帽U NUTS焊接螺帽WELD NUTS轮毂螺帽WHEEL NUTS蝶形螺帽WING NUTS锌压铸螺帽ZINC DIE CASTING NUTS铝钉ALUMINUM NAILS马达轴承轴心组件BEARING SHAFT（MOTOR）轴承轴心BEARING SHAFT开口铆钉BIFURCATED RIVETS长形拉帽（长型螺帽）BINDER POSTS（ANCHOR NUTS）拉帽BLIND NUTS (RIVET NUTS)拉钉BLIND RIVETS电梯壁虎BOLT ANCHOR金属粘着橡胶华司（双层华司）BONDED WASHERS铜钉BRASS NAILSC型扣环C-RINGS小眼钉CEILING HANGER化学壁虎CHEMICAL STUD实心梢CLEVIS PINS & STRAIGHT PINS弹片CLIPS卷钉COIL NAILS冷锻零件COLD FORMING PART开口梢COTTER PINS洋钉钩CUP HOOKS弧型华司CURVED WASHER外迫壁虎CUT ANCHOR插梢DOWEL PIN捶钉DRIVE RIVET壁虎DROP IN ANCHORE型环E-RINGS膨胀螺栓EXPANSION ANCHOR BOLTS难眼钉EYELETS RIVETS门钩GATE HOOKS插沟销GROOVED PINS有槽钢钉GROOVED STEEL NAILS火药钉GUNPOWDER NAILS壁钩HARDWALL HANGERS双片夹壁虎HEAVY DUTY SHIELD ANCHOR R型梢HITCH PINS（SNAP PINS）空心钉HOLLOW RIVETS洋钉IRON NAILSJ钩J HOOKK.D. FITTING K.D. FITTING闩锁LATCHES & KEEPER ASSEMBLEDS多冲程铆钉MULTI-STAGE RIVERS锤钉壁虎NAIL IN ANCHOR尼龙壁虎NYLON (METAL) FRame ANCHOR 塑胶华司NYLON WASHERS其他特殊铆钉OTHER SPECIAL RIVETS样品钩PEGBOARD HOOK吊图钩PICTURE HANGERS梢PINS各式管夹，管束PIPE HANGER管塞PIPE PLUG塑胶壁虎PLASTIC NYLON ANCHORSPOP拉钉系列产品POP RIVETS快速插销QUICK RELEASE PINSR型扣环R-RINGS扣环RINGS铆钉RIVETS圆棒铁钉ROUND IRON NAILST型铁钉ROUND IRON TAPE T NAIL圆棒钢钉ROUND STEEL NAILST型钢钉ROUND STEEL TAPE T NAILSU型钢钉ROUND STEEL TAPE U NAILS橡胶华司RUBBER WASHERSS钩S HOOKSS型扣环S-RINGS螺旋铝钉SCREW ALUMINUM NAILS螺旋环(洋眼) SCREW EYES螺旋钩及螺旋圈SCREW HOOK & SCREW RINGS 螺丝钩SCREW HOOKS螺旋铁钉SCREW IRON NAILS螺旋钢钉SCREW STEEL NAILS中空铆钉SEMI-TUBULAR RIVET套管壁虎SLEEVE ANCHOR实心铆钉SOLID RIVETS特殊华司SPECIAL WASHERS快速铆接扣件SPEED RIVETING开叉钉SPLIT DRIVE ANCHORS弹簧梢SPRING PIN弹簧华司SPRING WASHERS弹簧蝴蝶夹SPRING WINGS折钉SQUARE HOOKS不锈钢钢钉STAINLESS STEEL NAILS不锈钢中空钉STAINLESS STEEL SEMI-TUBULAR RIVET不锈钢斜纹钉STAINLESS STEEL SLANTING STRIPES NAILS 不锈钢华司STAINLESS STEEL WASHERS钢铁钉STEEL & IRON NAILS钢钉STEEL NAILSL型钢钉STEEL TAPE L NAILS铁马钩STORAGE HOOK吸盘钩SUCTION HANGERS兰花钩SWAG HOOKS三角吊钩SWIVEL LOOP HANGERS地毯钢钉TACKED IRON NAILS搓牙铁钉THREAD NAILS大眼钉TIE WIRE SPADE STUD钛合金铆钉TITANIUM ALLOY RIVETS钛合金膨涨螺丝TITANIUM ALLOY EXPANSION BOLTS钛华司TITANIUM WASHERS齿型华司TOOTH LOCK WASHERS管形铆钉TUBULAR RIVETS双向迫紧器TURNBUCKLE节牙钢钉W/STRIP STEEL NAILS华司WASHERS波浪型华司WAVE WASHER拉涨壁虎WEDGE ANCHOR线圈WIRE锌合金壁虎ZINC ALLOY FRame ANCHOR螺丝，螺帽，五金，DIY扣件ALL KINDS OF PACD AGING SERIES 合金钢工具ALLOY STEEL TOOLS电子手把HANDLES FOR ELECTRONIC DEVICES六角板手HEXAGON KEYS螺丝起子POWER BIT螺丝起子SCREWDRIVER BIT电动螺丝起子AUTOFEED SCREWDRIVER工具套筒组件SOCKET SETS套筒SOCKETS板手WRENCH自动炼带螺丝枪AUTOFEED SCREW DRIVER合金钢线材盘元ALLOY STEEL WIRE ROD铝合金锭ALUMINUM ALLOY球状化线材ANNEALING WIRE & ROD黑铁丝BLACK WIRE黄铜棒线BRASS WIRE & ROD磨光棒钢BRIGHT STEEL BAR (HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD镀锌铁线GALVANIZED STEEL WIRE线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHOR BRONZE WIRE各种表面处理用喷砂材料SAND BLASTING MATERIALS不锈钢条棒STAINLESS STEEL BAR (ROUND/HEX/SQUARE) 不锈钢冷锻线材STAINLESS STEEL COLD HEADING WIRE 不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE不锈钢网线STAINLESS STEEL NET WIRE不锈钢特殊线STAINLESS STEEL SPECIAL WIRE不锈钢弹簧线STAINLESS STEEL SPRING WIRE不锈钢线材STAINLESS STEEL WIRE不锈钢线材及盘元STAINLESS STEEL WIRE & ROD棒钢STEEL BAR(HEX/ROUND/SQUARE)钛、锆、钼、铌等螺丝、零件、材料TI、ZR、MO、NB PARE METAL BOLTS PARTS锌合金锭ZINC ALLOY立体/平面雕刻机3D DIE-SINKING MACHINE/ENGRAVING MACHINE转回90度辗线头机90°REVOLVING WIRE TWISTING MACHINE 干燥机AIR DRYER气动拉钉机AIR RIVETER铝不锈钢六角头螺栓，低合金熔解热处理炉ALUMINUM & LOW ALLOY MELTING FURNACE铝散热器烧焊热处理炉ALUMINUM BRAZING FURNACE FOR ALUMINUM CONDENSER不锈钢线材连续式光辉热处理退火炉ANNEALING FURNACE SPECIALLY FOR STAINLESS WIRE小型脱油机ANTI-OIL MACHINE自动包装机AUTOMATIC PACKING MACHINE螺丝自动检查设备AUTOMATIC SCREW SORTING MACHINE 自动送锁螺丝机AUTOMATIC SCREWING MACHINE螺丝割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE 螺丝制造成型机械AUTOMATIC TRIMMING MACHINE箱式渗碳氮化炉BATCH TYPE CARBURIZING & MITRIDING FURNACE钟罩式退火(球化)炉BELL TYPE SPHEROIDIZING ANNEALING FURNACE拉帽成型机BLIND NUT FORMERS拉钉打头机BLIND RIVET HEADING MACHINE螺丝(栓)成型机BOLT FORMERS螺丝、螺帽成型机BOLT FORMERS，NUT FORMERS六角头螺栓c级沉头内六角螺栓，HEADERS螺栓模BOLT HEADING DIES螺丝、螺帽热处理BOLT，NUT & SCREWS HEAT TREATMENT 螺丝、螺帽热处理炉BOLT六角螺栓，NUT & SCREWS HEAT TREATMENT FURNACES 圆剪式打头机BUSH CUT-OFF HEADING MACHINE圆剪式空心打头机BUSH CUT-OFF HOLLOW HEADING MACHINE主模CARBIDE DIES剪模CARBIDE QUILLS不锈钢螺丝，扣件连续式光辉调质淬火炉CARBURIZING FURNACE FOR STAINLESS FASTENER球状化电气炖炉CARBURIZING FURNACE，VACUUM & BELL TYPE FURNACE流气式箱型炉(箱式，坑式，台车式，连续式) CIRCULATION FURNACE (BOX六角头螺栓尺寸沉头内六角螺栓，PIT，TRUCK，CONTINUOUS TYPE)CNC电脑雕刻机CNC ENGRAVING MACHINE卷钉制造机COIL NAIL COLLATOR连续式光辉渗碳六角螺栓，淬火六角螺栓六角头螺栓标记示例外六角螺栓，回火炉CONTINUOUS BRIGHT CARBURIZING & HARDENING FURNACE连续式光辉渗碳淬火炉CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE连续式光辉调质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中六角头螺栓标准，高热镀锌光辉连续炉CONTINUOUS BRIGHT HEAT TREAT FURNACE连续式光辉热处理炉(不锈钢，硬焊) CONTINUOUS BRIGHT TREATMENT (FOR STAINLESS，BRAZING)连续式光辉热处理炉CONTINUOUS TYPE BRIGHT HEATTREATMENT FURNACE耐腐蚀表面处理炉(耐炼) CORROSION RESISTANCE OF SURFACE TREATMENT FURNACE剪刀(螺丝模) CUT-OFF KNIVES集尘设备CYCLONE EQUIPMENT各种碳化钨制品设计制造DESIGN & MANUFACTURE OF TUNGSTEN CARBIDE PRODUCTS模具DIES & TOOLS钻尾模DRILL POINT DIES耐冲螺丝成型模具FASTENER FORMING DIES螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENTS’INSTRUMENTS精密过滤器FILTER滚沟牙板FLAT KNURLING DIES一般线材六角头螺栓标准，盘元，退火炉GENERAL WIRE，WIRE ROD ANNEALING FURNACE手动拉钉钳HAND RIVETER倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE白铁针HEADER PUNCHES FOR STAINLESS BOLT三角六角头螺栓标记示例六角头螺栓尺寸，四角，六角针HEADER PUNCHES IN VARIOUS DRIVES(1)米字，一字，梅花，零号针HEADER PUNCHES IN VARIOUS DRIVES(2)一字六角边冲头HEADER PUNCHES IN VARIOUS DRIVES(3)螺丝打头机HEADING MACHINE六角冲针HEX PINS六角冲模HEX RECESS PUNCHES六角冲模HEX TRIMMING DIES螺丝制造高速搓牙机械HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感应加热炉HIGH，MEDIUM六角头螺栓标记示例，LOW FREQUENCY INDUCTION HEATER空心打头机HOLLOW HEADING MACHINE热锻造机HOT FORMER冲销KNOCKOUT PINS雷射/影像筛选机LASER/OPTICAL SORTING MACHINE FOR SCREWS立式输送机LOADER机械螺丝牙板MACHINE SCREW THREAD ROLLING DIES PLATES螺帽用的冲具MANUFACTURE OF PUNCH MAKING BOLTS AND NUTS迷你成型机MINI-FORMERS铁钉滚牙机NAIL ROLLING MACHINE铁钉模具NAILS DIE成品自动收线机NON-STOP COILER精抽自动收线机NON-STOP COILER (SKINPASS)螺帽模NUT FORMING DIES螺帽成型机NUTS FORMERS螺帽攻牙机NUTS TAPPING MACHINE特殊零件成型机PARTS FORMING MACHINE脚踏板系列自动组立专用机PEDAL AUTOMATIC ASSEMBLING MACHINE十字四角复合针PH+SQ COMBINATION PUNCHES四角十字冲模十字冲模PHILLIPS PUNCHES十字割沟冲模PHILLIPS SLOTTED PUNCHES冲针壳PIN HOLDERS锁用中心零件PINS TAILPIECE抛光机/磨光台POLISHING MACHINE手握式螺丝自动供给锁紧机PORTABLE SCREW-DRIVING MACHINE粉末治金烧结，黑化炉POWDER METALLURGY & STEAM TREATMENT FURNACE米字冲模POZI PUNCHES冲模PUNCH DIES冲子PUNCH PINS冲针冲床引伸模具PUNCHING DIES罗拉成型机ROLLERS FORMERSRX，DX瓦斯变成炉，AX 氨气分解炉RX，DX GAS GENERATOR，AX AMMO GAS GENERATOR盐浴式热处理炉SALT BATH HEAT TREATMENT FURNACE各式表面处专用喷砂机SAND BLASTING MACHINE FOR SURFACE TREATMENT螺丝自动组合华司机器SCREW & WASHER ASSEMBLY MACHINE FOR SEMS机(踏)车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE 螺丝夹尾模SCREWS TAIL POINT DIES 钻尾螺丝成型机SELF-DRILLING SCREW FORMING MACHINE 钻尾模具SELF-DRILLING SCREW MAKING DIES止付螺丝成型机SET SCREWS FORMERS梅花冲头SIX LOBE PUNCHES一字冲模SLOT PUNCHES套筒成型机SOCKETS FORMERS碳钢盘元，线材，球状化热处理退火炉SPHEROIDIZING ANNEALING FURNACE FOR STEEL WIRE一般线材，盘元，螺丝合金炖炉SPHEROIDIZING BRIGHTANNEALING FURNACE球状化热理炉SPHEROIDIZING HEAT TREATMENT FURNACE 四角孔针具SQ PUNCHES四角冲模SQUARE RECESS PUNCHES不锈钢钻尾螺丝割尾STAINLESS STEEL SELF DRILLING SCREW MILLED POINT钻子TAP攻牙机TAPPING MACHINE自攻螺丝牙板TAPPING SCREW THREAD ROLLING DIES PLATES螺丝攻、车刀、模具TAPS DIES & TOOLS铁氟龙(TEFLON)及珐琅烧付炉TEFLON COATING FURNACE搓牙机铁屑牙离装置THREAD CHIP SEPARATOR滚牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLATES螺丝搓手机THREAD ROLLING MACHINE精密油压滚牙机THREAD ROLLING MACHINES货物捆绑系统TIE DOWN HARDWARE弹簧机周边零件TOOLING PERIPHERAL COMPONENT OF SPRING MACHINE六角整头模TRIMMING DIES HEXAGON碳化钨模具TUNGSTEN CARBIDE DIEUNILOCK SELF-LOCKING AND SEAL-LOCKING UNILOCK SELF-LOCKING ANDSEAL-LOCKING FASTENERS电镀化学原料VARIOUS ELECTROPLATING CHEMICALS立式单双层连续伸线机VERTICAL TYPE SINGLE DECK WIRE DRAWING MACHINE温锻造机WARM FORMER伸线机WIRES DRAWER特殊铆合扣件COLLARS (A BLIND FASTENER FOR HUCK INTL) 电器银接点CONTACT POINT螺丝DIY包装系列DIY SCREWS PACKING SERIES自攻螺纹衬套ENSAT THREAD INSERT螺丝、螺帽成型攻牙专用油FORMING & TAPPING OILS FOR BOLTS & NUTS FORMERS铰链HINGES热浸镀锌螺丝沉头内六角螺栓螺帽HOT DIP GALVANIZING。
最全的螺钉术语中英文对照
•acme screw thread爱克米螺纹•acme screw-thread阿克米制螺纹•adapter set screw接头调节螺钉•adjustable round split die with adjusting screw带调整螺钉的可调式圆板牙•adjustable screw type steering gear可调整式螺旋型转向装置•adjustable stop screw可调整止动螺钉•adjusting screw调整螺钉;调整螺丝;调准螺旋;调节螺钉;校正螺钉;校正螺旋•adjusting screw for elevation标高调整螺丝•adjusting screw for pan position锅体水平调节螺杆•adjusting screw for transverse横向调整螺丝•aerial screw飞机螺旋桨•aiming adjust screw瞄准调节螺钉•aiming screw瞄准调节螺钉•air intake adjusting screw进气调节螺钉•air screw空气螺旋桨•air-tight screw pump密闭式螺杆泵•Allen screw阿伦螺钉•allen screw六角固定螺丝•ampere's right handed screw rule安培右手螺旋定则•Ampere's right-hander screw rule安培右手定则•anchor screw基础螺栓•anchoring screw止动螺钉•annular screw plate环状板牙•antagonizing screw调置螺旋•antifriction ring holder screw减摩环托螺钉•arachnoid screw蛛网膜螺钉•arachnoid screw driver蛛网膜螺钉旋凿•Archimedean screw阿基米德螺线•Archimedean screw pump阿基米德螺旋泵•Archimedes'screw阿基米德螺旋•assembly screw安装螺旋•attachment screw连接螺钉;定位螺丝;止动螺钉•automatic screw lathe自动螺纹车床•automatic screw machine自动螺丝车床•auxiliary screw arc辅助螺钉弧形板•axis of screw螺旋轴线•azimuth adjusting screw方位调整螺钉•backing-up screw止动螺钉•backlash adjusting screw齿隙调整螺钉•ball screw滚珠丝杠•ball-bearing cap screw滚珠轴承盖螺钉•ball-jointed screw万向球铰螺杆•band wheel crank screw带轮曲柄螺丝•band wheel crank screw nut带轮曲柄螺丝帽•band wheel set screw带轮主头螺丝•banking screw止动螺钉•base screw底座螺钉•bearing for screw conveyer螺旋输送机轴承•bell screw钟形螺钉;丝锥接套•binding(post)screw接线螺钉•binding head screw扁头结合螺钉•blast cap screw鼓风盖螺钉•bleed screw带孔螺钉•body of screw螺钉体•body screw犁体螺钉•boiler lagging plate set screw锅炉套板止动螺钉•bolster screw jack车架螺旋千斤顶•bone screw接骨螺钉•bone screw and bolt outfit骨螺钉螺栓器械包•bone screw driver接骨螺钉旋凿•bone screw holding forceps接骨螺钉夹持钳•bone screw tap接骨螺钉丝攻•bottle screw螺旋起重机;螺旋起重器•bottom plate screw底板螺钉•brace screw撑柱螺丝•brace screw driver撑臂起子•brake screw制动螺杆•brake thrust screw制动器止推调节螺钉•brass countersunk head wood screw黄铜平头木螺丝•brass round head wood screw黄铜圆头木螺丝•brass screw down bib cock黄铜水龙头•brass screw down bib cock heavy type黄铜重型水龙头•brass shouldered cup screw hook黄铜螺丝弯钩•brass square screw hook黄铜螺丝曲尺钩•brass wood screw黄铜木螺丝•brass-plated mild steel round bead wood screw镀黄铜圆头软钢木螺丝•brass-plated mild steel round head machine screw镀黄铜圆头软钢机器螺丝•brazier head screw扁头螺钉•breaker arm adjusting screw断电臂调整螺钉•bright mild steel countersunk head wood screw光亮软钢平头木螺丝•bright mild steel round head wood screw光亮软钢圆头木螺丝•bronze screw hook古铜螺丝钩•bush set screw衬套制动螺钉•butterfly screw元宝螺钉•button-head cap screw圆头帽螺钉;半圆头紧固螺钉•button-head screw圆头螺钉•button-headed screw半圆头螺钉•buttress thread screw斜梯形纹螺钉•calibration screw校准螺钉•cap of screw螺钉帽•cap screw有头螺钉•capstan(-headed)screw绞盘螺钉•captive screw外加螺丝•carpenter's screw clamp台钳•carriage lock screw拖板锁紧螺钉•casale closure with external screw外螺纹卡扎里密封•central screw中心螺钉•centrifugal screw pump离心螺旋泵•centring screw定中心螺钉•chain adjusting screw链调节螺钉•chamfer head screw沉头螺钉•check screw止动螺钉•cheese head screw高平头螺丝•circumferential register screw圆周定位螺丝•clamp screw制动螺旋•clamp screw sextant制动螺钉六分仪•clamping screw固定螺钉•clip screw调置螺旋•closing screw螺纹规;螺纹塞•clutch adjusting screw离合器调整螺钉•clutch pressure plate screw离合器压板螺钉•coach screw方头螺钉;板头尖端木螺钉•coarse screw tap粗丝锥•coarse thread screw粗螺纹螺钉;粗纹螺钉•coarse-pitch screw大螺距螺钉•collar head screw头带缘螺钉•collar-head screw环头螺钉•combination screw driver set with tester带测电笔的套装螺丝刀•complete equipment for making wood screw木螺丝成套设备•compound feed-screw复式刀架丝杠•compound feed-screw graduated collar复刀架丝杠刻度圈•compound screw复式螺钉;复式螺旋•cone screw锥形螺钉•conical twin-screw extruder锥形双螺杆挤塑机•connecting screw rod连接螺杆•connection screw连接螺钉•constant taper screw等螺距锥体螺杆•contact screw接触螺钉•conveyer screw螺旋输送器•conveyer screw drive shaft输送机螺旋主动轴•conveyer screw shaft输送机螺旋轴•conveyer screw shaft coupling输送机螺旋轴联轴节•conveyer screw thrust plate输送螺旋止推板•copper-plated iron screw ring镀紫铜铁吊环螺钉•cored screw空心螺旋•correction screw校正螺钉;校正螺旋•correctional screw改正螺旋•cotter with screw end螺旋端锁销•countersunk head machine screw埋头机螺钉•countersunk head screw埋头螺钉•countersunk oval head screw埋头圆顶螺钉•countersunk screw埋头螺钉;埋头螺丝•coupling screw连接螺钉•cover screw盖用螺钉•credit screw信用紧缩•crest of screw thread螺纹牙顶•cross feed screw横进刀螺杆•cross feed screw crank横向进刀螺杆曲柄•cross feed screw dial横进刀螺杆指示盘;横向进刀螺杆指示盘•cross feed screw handle横向进刀丝杠手柄•cross lead screw横向丝杆•cross lead screw nut横向丝杆螺母•cross recess head screw十字槽头螺钉•cross screw左右交叉螺纹•cross slide screw横动台螺杆;横滑板螺杆•cross surfacing screw横动台螺杆•cross traverse screw横动台螺杆•crown screw牙冠用螺钉•cruciform screw driver十字形螺丝起子•cruciform slot screw十字槽螺钉•cup head screw半圆头螺钉;圆头螺钉•cup head wood screw圆头木螺丝;半圆头木螺钉•current regulator contact screw电流调节器接触螺钉•cutter for screw plate螺丝板加工刀具;螺丝板牙加工工具•decreasing lead screw减螺距螺杆•depth gauge for bone screw接骨螺钉长度测量器•depth screw gear耕深调节螺杆•depth-adjusting screw耕深调节螺杆•dial of vertical adjustable screw垂直可调丝杠•dial screw度盘螺钉•diameter of screw螺纹标称直径;螺旋直径•differential drive gear thrust screw差速器环齿轮推力螺钉•differential gear for screw conveyer螺旋输送机的差动装置•differential screw差动螺旋;差动装置螺钉•differential screw gearing差动螺旋传动装置•differential screw jack差动螺旋起重器•differential screw-jack差动螺旋千斤顶•differential-screw jack差动千斤顶•diopter rotating screw视度转螺•distributor adjusting screw分配调整器螺钉•dog(set;locating)screw定位螺钉•dog screw轧头螺钉;偏心头螺钉•dormant screw埋头螺钉•double flight feed screw双头螺旋加料器•double screw pump双螺杆泵•double worm screw双扭螺钻;麻花钻•double-screw bolt螺柱•double-screw washer双螺旋洗矿机•double-thread screw双头螺纹•double-threaded screw双纹螺钉•dowel screw扶手螺丝;两头螺钉;两头螺丝钉•down-feed screw垂直丝杠•draw screw起拉螺钉;起模螺钉•drive screw螺纹钉•driving screw导螺杆;导螺旋;主螺杆•drivre screw传动螺杆•duct adjusting screw墨斗调节螺丝•earth screw土钻;挖穴钻•earthing screw接地螺钉•eccentric-screw breechblock偏心闭锁机•Edison screw爱迪生螺纹;圆螺纹•electric screw clay gun电动螺旋式泥炮•electric screw down gear电动压下装置•electric screw driver电动螺丝刀;电动螺旋钻•electro-magnet screw press电磁螺旋压力机•electro-mechanical screw time release机电螺旋式限时解锁器•elevating endless screw升降蜗杆•elevating screw升降丝杠;上升螺旋;螺旋起重器•elevator screw升降机螺旋•endless screw蜗杆•endless tangent screw sextant微调螺杆六分仪•engine idling speed adjusting screw发动机怠速调整螺丝•English screw英制螺纹•English screw pitch ga(u)ge英制螺距规•Ericsson screw埃里克森螺纹•expansion screw扩开螺钉;可调螺钉•extension screw螺旋延长部•external screw螺钉•external screw cutting tool外螺纹车刀•external screw ga(u)ge外螺纹检查规•external screw thread finish外螺纹瓶口•extra fine screw特细牙螺纹•extruder screw压出机螺杆•extruding screw挤压螺杆•eye screw羊眼螺丝;吊环螺栓;环首螺钉;环首螺栓•eyepiece screw目镜螺丝;目镜螺旋•eyepiece screw-micrometer螺杆式目镜测微计•faceplate screw面板螺丝•faller screw针板螺杆•falt fillister screw凹槽扁头螺杆•fastening screw紧固螺钉•feed screw进给螺杆;螺旋给料机;螺旋送料机•feed screw collar进给螺杆挡环•feed screw mechanism进料螺杆机构•feed screw nut丝杆螺母•female screw阴螺丝;阴螺旋;螺母;内螺旋•female screw thread内螺纹•femoral screw股骨螺钉•ferrous and non-ferrous screw and nut黑色及有色金属螺钉和螺母•fillet of screw螺纹圈•filling screw螺纹规•fillister head screw凹槽帽螺钉•fine adjustment screw微调螺丝•fine screw tap细牙螺丝攻•fine thread screw细纹螺钉•fine-motion screw微动螺旋•fine-pitch screw细牙螺钉•finite-conductivity screw instability有限电导率螺旋不稳定性•fitting screw紧配连接螺栓;装配螺钉•fix screw固定螺丝•fixation screw needle固定螺丝针•flat counter-sunk head screw平顶埋头螺钉•flat end set screw平端固定螺钉•flat head screw平头螺钉;平头螺丝•flat point set screw平端定位螺钉•flat screw平头螺钉•flexible screw conveyer挠性螺旋输送器•flush head screw shackle平头螺栓卸扣•flux screw磁通调整螺钉•fly-headed screw蝶形头螺钉•focusing screw调焦螺旋•foot screw地脚螺钉;地脚螺丝;脚螺旋•foot-screw底脚螺丝•for screw stays用于螺丝固定•force screw力旋量•forcing screw紧固螺钉;起重器;加压螺钉•forked screw driver叉形螺丝刀;叉形螺旋起子•four-screw driver四用螺钉起子•four-screw leveling head四螺钉安平头•four-wheel screw jack四轮修车起重器;四轮修车起重器•friction screw press摩擦螺旋压力机;摩擦压力机•front screw前螺杆•fuel pump adjusting screw燃油泵调节螺钉•full-automatic screw machine全自动螺丝机床•full-flighted screw全程螺杆•fully automatic turret screw machine全自动转塔式车床•galvanized iron corn head screw镀锌尖头螺丝•galvanized iron screw白铁螺丝•galvanized iron screw hook镀锌螺钩•galvanized mild steel countersunk head wood screw镀锌沉头木螺丝•galvanized mild steel drive screw镀锌螺丝钉•galvanized mild steel roofing screw镀锌瓦楞螺丝•galvanized mild steel round head machine screw镀锌圆头机器螺丝•galvanized mild steel round head wood screw镀锌圆头木螺丝•galvanized MS countersunk head machine screw镀锌平头机器螺丝•galvanized screw镀锌螺钉;镀锌螺丝•galvanized screw plug镀锌旋塞•galvanized stay adjustable screw镀锌拉线调整螺丝•galvanized steel self tapping screw镀锌自攻螺线•gas valve screw气阀螺钉•gathering screw收集螺旋•gear motor for screw conveyer螺旋输送器减速电动机•geared worm screw传动蜗杆螺旋•generator frame through screw发电机架长螺杆•gib screw调整楔用螺钉;夹紧调整螺钉•governing screw调节螺钉•governor adjusting screw调节器调整螺钉•governor adjusting screw cap调速器调整螺钉帽•governor arm screw调速器杆螺钉•governor link screw调节器联杆螺钉•grain screw谷粒螺旋•grid of screw dislocations螺形位错十字格•grooved bone screw有槽接骨螺钉•ground screw地脚螺钉•grub screw平头螺钉;平头螺丝;木螺钉;木螺丝•guide screw导螺;丝杆•hairspring screw游丝螺钉•hairspring stud screw游丝外桩螺钉•half-bright screw半光制螺钉•half-round head screw半圆头螺丝•half-round screw半圆头螺钉•hammer-drive screw锤入式螺钉•hand brake band anchor bar adjusting screw手闸带锚定杆调整螺钉•hand driven screw press手动平板机•hand jack screw手力千斤顶•hand power screw press手动螺旋压机•hand power screw punching press手动螺旋压孔机•hand screw手动螺杆;手力千斤顶•hand screw clamp手螺旋夹•hand screw holdfast手螺旋夹•hand screw press手动螺旋压力机;手转压力机•hand screw tap手用丝锥•hand wheel screw down手轮压下装置•hand-operated screw press手动螺旋压力机•hand-operated vertical screw press手摇立式螺旋压榨机•hand-screw手动起重器•hand-screw vulcanizing press手旋硫化机•handle set screw车辆制动螺钉•handrail screw扶手螺丝•head lamp adjusting screw前灯调节螺钉•headless screw无头螺钉•headless set screw无头止动螺丝•headless shoulder screw无头轴肩螺钉•helical screw pulp conveyer螺旋纸浆传送器•helically bladed screw conveyer螺旋叶片式输送器•hermetic screw pump密闭式螺杆泵•hex socket screw key六角凹头螺钉键•hexagon cap screw六角帽螺钉•hexagonal head screw六角头螺钉;六角头螺栓•hexagonal socket screw六角凹头螺钉•high power screw press高能螺旋压力机•high precision lead-screw cutting lathe高精度丝杠车床•high viscosity triple screw pump高粘度三螺杆泵•holding screw紧定螺钉;紧固螺丝•holes for screw螺栓孔•hollow screw空心螺钉•hollow-head set-screw空心头固定螺钉•hook screw钩头螺钉;带钩螺钉•horizontal clamping screw水平制动螺钉•horizontal light beam adjusting screw水平光调节螺钉•horizontal parallax screw水平视差螺旋•horizontal screw pump卧式螺旋泵•housing adjusting screw压下调整螺丝•housing screw压下螺丝•Hunter's screw差动可逆可螺旋桨•hydraulic cylinder bleeder screw液压缸放出管螺钉•hydraulic screw press液压螺旋压力机•hyperbolic screw pump双曲线式螺杆泵•image screw映像旋量•impedance screw节流螺钉•impeller locking screw叶轮端螺钉•inboard screw内侧螺旋桨•inch screw die英制螺纹板牙•inch screw tap英制螺纹丝锥•independent screw chuck分动螺旋卡盘•inside screw螺母•inside screw and non-rising stem暗杆内螺纹•inside screw and rising stem(ISRS)明杆内螺纹•inside screw rising stem内螺纹明杆•instrument headed screw半埋头螺钉•internal screw内螺旋•internal screw cutting tool内螺纹车刀•internal screw finish内螺纹瓶口•internal screw ga(u)ge内螺纹规•internal screw pump内螺旋泵•internal screw thread内螺纹•international screw die公制螺丝钢板•international screw pitch gauge国际螺距规;国际螺距规•international screw tap公制丝锥•international screw thread国际标准螺纹•interrupted screw带槽螺钉•iron handle screw driver铁柄螺丝刀•iron screw铁螺钉•iron screw with square head方头铁螺钉•iron square head screw方头铁螺钉•iron wood screw铁制木螺钉•jack screw螺旋起重机;千斤顶螺杆;千斤顶螺丝•jack(ing)screw螺旋千斤顶•jacket band screw套带螺钉•jacking screw顶起螺丝•key screw螺丝把;螺旋键•kingpin stop screw主销定位螺丝•knuckle stop screw关节止动螺钉•knurled screw滚花螺钉;滚花螺杆•lag screw板头尖端木螺钉;方头螺钉•lag wood screw木螺钉•lang raising screw地轮起落螺杆•large flat head slotted screw大平槽头螺钉•latch bracket screw弹键托螺钉•latch screw弹键螺钉;门栓大螺丝•lead of screw螺旋导程•lead screw导螺杆;唱片盘首纹;丝杆;丝杠;引入槽•lead screw for cross-slide横向进给螺杆•lead screw for saddle床鞍螺杆•lead screw for top slide刀架螺杆•lead screw monocomparator导杆螺旋单象坐标仪•lead screw tester丝杆检查仪•lead-in screw引入螺钉•lead-screw导螺杠•lead-screw drive导螺杆驱动•lead-screw gear丝杠交换齿轮•leading screw lathe丝杠车床•leading screw support导螺杆轴承•left screw左螺旋•left-hand screw左螺旋•left-hand screw drill pipe反扣钻杆•left-handed screw左旋螺杆•lentil-headed screw扁头螺钉•level(l)ing screw校平螺旋•levelling screw水准螺旋•lever latch cap screw手柄弹键盖螺钉•lift link screw提升杆调整螺杆•lift(ing)screw螺旋起重器•lifting screw起模螺钉;千斤顶螺杆;升降螺杆•limit screw止动螺钉•limit screw pitch ga(u)ge螺距极限规•linkage levelling screw悬挂装置;调平螺杆•lock screw锁定螺钉•locking screw锁紧螺钉•log screw方头木螺丝;木螺钉;木螺丝•long bent point screw长弯头画线针•long lead screw长丝杠•long screw长螺丝•longitudinal parallax screw纵向视差螺旋•low noise air screw compressor低噪声螺杆空气压缩机•lubricating screw润滑螺旋;黄油枪•machine screw with oval countersunk fillister head半沉头螺钉•main(driving)screw主螺杆•main pin brass cotter set screw主销铜衬扁销止动螺钉•main valve head cap screw主阀盖有头螺钉•male screw阳螺旋;柱螺纹•male screw cutting tool外螺纹车刀•male screw thread外螺纹;阳螺纹•manual control screw手调螺钉•manually-operated screw手动压力螺丝•marine screw propeller船用螺旋桨•marking screw标号螺丝•marsh screw amphibian沼地螺旋推进水陆两用车•mass screw平衡螺钉•master screw母丝杠;标准螺旋•Maurer type screw press毛雷尔型螺旋压榨机•maximum fuel limit screw最大燃油限制螺钉•meantime screw调时螺钉•measuring screw测微螺丝•medium Edison screw-cap中等爱迪生螺旋灯头•medium egg-plant screw indicating lamp bulb中螺口茄形指示灯泡•meter screw公制螺纹•metering screw计量螺旋•metric screw pitch gauge米制螺距规;国际螺距规•metric screw thread公制粗牙螺纹;公制螺纹•micrometer adjusting screw微调螺钉•micrometer screw千分丝杠;微调螺钉•micrometer screw caliper测微螺旋卡尺•micrometer screw ga(u)ge螺旋测微计;螺旋千分尺•micrometric regulating screw微调螺钉•micrometric screw测微螺杆;测微螺旋•mill headed screw滚花头螺钉•mill screw轧机压下螺丝•milled edge thumb screw铣边翼形螺钉•milled screw滚花头螺钉•minimum fuel limit screw最小燃油限止螺钉•minus screw一字槽头螺钉•mirror screw镜螺旋;镜螺旋;镜面螺钉;镜面螺钉•mixer-with conical screw锥形螺旋搅拌机•mixing screw螺旋混合机;混合螺杆;混合用螺旋•mixing screw conveyer混合螺旋输送器•monkey screw wrench活扳手•mounting screw安装螺钉•multi-start screw thread多头螺纹•multiple-start screw thread多头螺纹•multiple-thread screw多头螺杆•multiple-threaded screw多头螺杆;多纹螺旋•mushroom head screw菌头螺钉;菌头螺钉•Napier's differential screw steering gear纳皮尔差动螺旋操舵装置•neck(ed)screw颈口螺旋;颈口螺旋•needle bar connecting link hinge screw麦果螺丝•nickel-plated double line iron screw hood镀镍双线螺旋帽•nickel-plated double line iron screw hook镀镍双线螺旋钩•nickel-plated iron screw eye镀镍铁螺丝眼•nickel-plated iron screw hook镀镍铁螺旋钩•nickel-plated mild steel round head machine screw镀镍低碳钢圆头机器螺丝•nickel-plated mild steel round head wood screw镀镍低碳钢圆头木螺丝•nickel-plated steel self tapping screw镀镍钢制自攻螺丝•no screw balance无平衡螺钉摆轮•nozzle adjusting screw喷管调节螺钉•nut screw螺母•observation tube fixing screw抽筒固定螺旋•odd-pitch screw非标准螺纹•oil cup cover screw油杯盖螺钉•oil pressure adjusting screw油压调节螺钉•oil pressure switch screw油压开关螺丝•oil reservoir cover screw储油器盖止动螺钉•oil-hole screw油孔螺钉•oil-pressure adjusting screw油压的调节螺丝•one start screw单头螺纹•open screw gill drawing frame单针并条机•oscillating screw摆动螺钉•outer set screw外固定螺钉•outside screw and yoke type(OS&Y)轭式外螺纹•outside screw non-bonnet(OSNB)无压盖外螺纹•oval countersunk fillister head machine screw半沉头机器螺钉•oval countersunk fillister head wood screw半沉头木螺钉•oval countersunk screw椭圆埋头螺钉•oval fillister head screw球面圆柱头螺钉•oval head screw椭圆头螺丝•oval slotted countersunk head unloosing screw半沉头不脱出螺钉•packing screw衬垫螺旋•paddle screw conveyer叶片式螺旋输送器•panhead screw大柱头螺钉;锅头螺丝•pattern screw起模螺钉•percussion screw press直接电动螺旋锤;直接电动螺旋压力机•Persian screw螺旋排水机•Philips screw菲氏螺钉;带十字槽头的螺钉•Phillips screw菲利浦螺钉;十字槽螺钉•pilot screw支持螺丝•pinching screw夹紧螺钉;固定螺钉•pipe screw-cutting lathe管子螺纹车床•piston heat set screw活塞头止动螺钉•piston pin locking screw活塞销锁紧螺钉•piston pin set screw活塞销锁紧螺钉•piston stop screw活塞头止动螺钉•pivot screw枢轴螺钉•pivot-point screw枢轴螺旋•plain bone screw无槽接骨螺钉•plain screw平螺钉•plain-ended screw平端螺钉•plug machine screw tap机用中丝锥•plug screw螺塞•plug screw ga(u)ge阴螺纹规•plus screw十字槽头螺钉•plus-minus screw调整螺钉;调整螺丝;调整用螺钉•pneumatic screw press气动螺旋压机•pointless screw平端螺钉•porcelain head screw瓷头螺丝•porcelain screw holder瓷螺丝灯头•porcelain screw socket瓷螺丝灯座•positioning screw定位螺钉•positive-column screw instability螺旋不稳定性•positive-displacement screw type compressor正排量螺旋式压气机•pottery topped brass screw瓷头铜螺丝•power screw传动螺杆;传力螺钉•power transmission screw动力传动螺杆•power-driven screw-jack set电动螺旋起重机组•precision lead screw精密丝杠•pressure regulating thumb screw压脚调节翼形螺钉•pressure screw压力螺钉;压下螺丝•pressure screw check nut压力螺钉防松螺母•pressure screw extractor螺旋压榨机•pressure-adjusting screw压力调整螺钉•proportion set screw比例度设定螺丝•pull-out piece spring screw压簧螺钉•push-pull screw推拉螺杆•pusher screw推进式螺旋桨•quadruple screw四头螺旋;四纹螺旋;四线螺旋•quadruple screw motor ship四螺旋桨船•quick-motion screw速动螺旋•radial feed screw径向进给丝杠;径向进给丝杠•radiator screw-cap散热器加水盖•rag screw棘螺栓•raised head screw凸头螺钉•rapid screw大节距螺钉•ratchet screw jack棘轮螺旋起重器•reaming holes for screw stays为固定螺钉用的铰孔•rear furrow wheel adjustment screw尾轮调节螺钉•rear screw shaft后螺旋桨•rear screw shaft bushing后螺轴衬套•recalibration screw重新校准螺钉•recessed-head screw-driver槽头螺丝刀•rectilinear screw-thread reluctance motor直线螺纹磁阻电动机•reduction screw螺旋还原反应器•regular screw thread基本螺纹•regular screw threads普通螺纹•regular thumb screw对称翼形螺钉•regulating screw调整螺钉;调整螺丝•regulating stem set screw调节杆止动螺钉•regulator spring screw调节簧螺钉•restriction screw节流尖头螺钉;节流螺旋杆;带螺纹针阀•restrictor screw节制孔螺钉•retainer screw护圈螺钉•retaining screw固定螺钉•retention screw止动螺钉;定位螺钉;紧固螺钉•reverse screw回动丝杠•reverse-flighted screw双向螺杆•reversing screw回动螺旋•reversing screw bolt回动螺栓•reversing screw bottom guide回动螺杆下导板•reversing screw gudgeon回动螺旋•reversing screw top guide回动螺旋上导板•revolution speed of screw螺旋转速•ribbon type screw conveyer带状螺旋运输机•rigging screw装配螺钉;松紧螺旋扣;系紧螺钉•rigging-and-left-hand-screw clip左右向螺杆夹•right-and-left screw左右旋螺栓•right-hand screw右螺旋•right-hand screw rule右手螺旋定则•right-hand screw thread右螺纹;右旋螺纹•right-handed screw右旋螺钉;右旋螺旋杆•right-handed thread screw右螺纹螺杆•ring screw环头螺钉•ring screw ga(u)ge螺纹环规•rolled-thread screw滚丝螺钉•rolling mill screw down轧机的压下装置•rotary helical screw compressor回转式螺杆压缩机•rotary screw compressor旋转螺旋压缩机•rotation set screw转动限位螺钉•round head wood screw圆头木螺钉•round wood screw圆头木螺钉•roundhead screw圆头螺钉•roundheaded wood screw圆头木螺丝•saddle feed screw鞍架进给螺杆•saddle traverse screw鞍架进给螺杆•safety locking screw保险止动螺钉•safety set screw安全螺丝;安全止动螺钉•scoketed screw凹头螺钉•screw螺钉;螺丝;螺旋•screw action捻旋作用•screw adjusting double caliper螺钉调整内外卡尺•screw adjusting inside caliper螺钉调整内卡尺•screw adjusting outside caliper螺钉调整外卡尺•screw adjustment螺钉调整•screw and double nut螺丝和双螺母•screw arbor螺杆•screw auger推运螺旋•screw axes螺旋对称轴•screw axis螺旋轴•screw base螺钉座•screw base fuse螺旋式熔断器•screw bell钻杆打捞器•screw belt螺钉带•screw belt fastener螺钉带扣•screw blade螺旋刀片;螺旋桨叶;螺旋式叶片•screw blank螺钉坯件•screw bolt螺杆;螺栓;全螺纹螺栓•screw bolt and nut螺栓和螺母•screw brake螺杆闸•screw bushing螺旋轴衬•screw cap螺母;螺丝管帽;螺丝帽•screw capping拧盖•screw case螺杆箱•screw case box螺杆箱机座•screw case suppressing metal螺杆箱紧固件•screw chaser螺纹板牙;螺纹梳刀;修正孔用丝锥•screw chases螺丝版框•screw chasing螺纹切削•screw chasing machine螺丝车床;螺纹切削机;制螺旋机•screw chasing tool螺纹梳刀•screw clamp螺丝夹;螺旋夹•screw clamp for brake shoe lining装制动磨擦夹片•screw clamp for lubricating leaf spring钢板弹簧上油卡子•screw coal conveyer螺旋式输煤机•screw coal unloader螺旋卸煤机•screw collar螺旋环;环状螺母•screw comb螺纹梳刀•screw composing-stick螺丝排字手托•screw compressor螺旋压气机;螺旋压缩机•screw compressor clamp螺旋压缩机管夹•screw cone螺旋锥体•screw contact螺丝触点•screw control压下控制•screw conveyer螺旋输送机•screw correction螺旋形失真校正•screw cramp螺丝夹钳•screw cutter螺纹刀具•screw cutting螺纹切削;切螺纹;切削螺纹;车螺纹•screw cutting dies板牙•screw cutting lathe车螺丝车床;螺丝车床•screw cutting machine螺纹切削机;螺旋切削机•screw decanter螺旋沉降器;螺旋澄清器•screw depth control螺杆式深度调节器•screw depth regulator螺旋式入土深度调节器•screw diad二重螺旋轴•screw diameter螺旋直径•screw die螺丝板牙;平丝板•screw dislocation螺线位错;螺旋位错•screw displacement螺旋位移•screw drive螺杆传动•screw driver螺丝批•screw driver with wooden scales夹柄螺丝批•screw drum螺旋转鼓•screw elevator螺旋升运器;螺旋式升降机;螺旋提升机;螺旋牙根挺•screw extractor断螺钉取出器;起螺丝器•screw extruder螺旋挤压机;螺旋压出机•screw extrusion machine蜗杆挤压机•screw extrusion press螺旋挤出机;螺旋挤压机•screw eye螺丝眼•screw eye(羊眼)羊眼圈•screw fan螺旋扇风机;轴流式扇风机•screw fastener螺钉扣•screw fastening螺钉连接;螺丝接合•screw feed螺旋喂送器•screw feed grease cup滑脂杯•screw feed mechanism螺旋加料机构•screw feeder螺杆给料机;螺旋加料器•screw fixing螺丝固定•screw flange栓接法兰•screw flange coupling螺钉凸缘联轴节•screw for alarm clock闹钟螺钉•screw for bearing wheel of oscillating weight自动锤轴承螺钉•screw for framework of automatic device自动框架螺钉•screw for indicator guard日历指示器护板螺钉•screw for jumper spring跳杆簧螺钉•screw for motor starter马达起动器螺钉•screw for setting lever spring压簧螺钉•screw for starter fixing clamp起动器固定夹螺钉•screw friction press螺旋摩擦压力机•screw ga(u)ge螺纹规•screw ga(u)ge(S.G.)螺纹量规•screw gauge for taper thread锥形螺纹量规•screw gear螺纹传动装置;螺旋齿轮;压下装置•screw gearing螺旋齿轮传动装置;蜗轮蜗杆传动装置•screw gill drawing frame螺旋杆式并条机•screw gun螺旋式油枪•screw head file螺钉头锉•screw height control螺杆式高度调节器•screw holder螺口灯头;螺丝夹持器•screw holding forceps持螺丝钳•screw home拧紧•screw hoop环首螺栓•screw horseporew推进器马力•screw housing clearance推运螺旋与壳间间隙•screw hub seal蜗杆毂密封•screw impeller螺旋叶轮•screw impeller pump螺旋桨式泵•screw jaw with lug带舌螺扣接杆•screw jaw with movable lug带活舌螺扣接杆•screw joint螺管接头;螺旋接合•screw key螺丝扳手;螺旋键•screw lid螺旋盖•screw lift螺旋提升机•screw lifting mechanism螺旋提升机构•screw lower bridge of automatic device自动装置下夹板螺钉•screw lubrication螺旋润滑•screw machine自动车床;制螺钉机•screw making machine制螺钉机•screw mandrel螺旋心轴;丝杆•screw micrometer螺杆测微计•screw micrometer cal(l)iper螺旋千分卡尺•screw microscope螺旋测微镜•screw mixer螺旋轴搅拌机•screw motor螺杆马达•screw nail螺丝钉;螺纹钉;木螺钉•screw nicking machine螺钉头开槽机•screw nut螺母•screw of tangential cutter head切向进刀架丝杠•screw off拧松•screw on拧上•screw pair丝杠螺母副;螺旋副•screw pile螺旋桩•screw pile foundation螺旋桩基•screw pin螺旋销•screw pin countersink shackle埋头螺丝卸扣•screw pinch螺旋箍缩•screw pitch螺纹距;螺旋节距•screw plasticating injection molding螺杆塑化式注塑•screw plate螺丝板牙;螺丝钢板;螺丝模;搓丝板;搓丝机;板牙•screw plow螺旋形犁•screw plug螺旋接线柱;螺旋塞•screw plug ga(u)ge螺纹塞规•screw press螺旋压机;螺旋压力机•screw prop千斤顶•screw propellor for boat船用螺旋桨推进器•screw pump螺杆泵;螺旋泵•screw punch螺旋冲压机•screw rack斜齿条•screw rail bender螺杆弯轨机•screw release螺旋式限时解锁器•screw remover去螺钉器•screw retention螺纹防松装置•screw reverse gear螺旋回动装置•screw ring环首螺钉•screw ring ga(u)ge螺纹环规•screw rivet螺纹铆钉;螺旋铆钉•screw riveting machine螺旋铆机•screw rod螺杆•screw rolling machine滚丝机•screw rule螺旋定则•screw shackle螺纹联接环;螺纹连接环•screw shaft螺杆轴;螺旋轴•screw shaft bushing螺旋轴衬套•screw shank螺钉杆•screw shaped mo(u)ldboard螺旋形犁壁•screw shaving machine制螺母及螺栓头机•screw sheel螺旋套筒;灯头螺口•screw shell螺旋套管•screw snap ga(u)ge螺纹卡规•screw socket螺丝灯头;螺丝套筒•screw spike螺丝钉;螺纹道钉;螺旋道钉•screw spindle螺旋轴•screw spreader螺旋传送器;螺旋分布器•screw stairs盘旋式楼梯•screw stem螺杆•screw stock螺旋扳手•screw stopper螺旋塞•screw stud双头螺栓•screw support for adjusting regulator调整快慢针的螺钉座•screw swinging mechanism螺旋摆动机构•screw tap丝锥•screw templet螺纹样板•screw terminal螺丝接线端•screw testing interferometer螺杆检验干涉仪;检验螺纹干涉仪•screw tight fitting紧配螺旋•screw tightener压紧螺钉•screw tip蜗杆梢•screw tourniquet螺旋止血带•screw tow bar螺旋式牵引杆•screw triad三重螺旋轴•screw tube罗纹管•screw type oil expeller螺旋榨油机•screw unit组合机床的动力头•screw up拧紧•screw value螺旋周值•screw valve螺旋球阀•screw vent螺杆通孔•screw ventilation螺旋桨式风机;螺旋通风器•screw vice螺旋虎钳•screw washer螺旋垫圈;螺旋洗矿机•screw wedge丝杆调节楔•screw willow螺旋威罗机•screw winder螺杆式络纱机•screw wiper螺旋式擦拭器•screw wire螺钉用钢丝•screw with diamond knurls金刚石滚花头螺钉•screw with flat head平头螺钉•screw with knurled head滚花头螺钉•screw with round head圆头螺钉•screw with straight-line直线滚花头螺钉•screw with straight-line knurls直线滚花头螺钉•screw without nut无帽螺钉•screw worm螺旋锥蝇幼虫•screw wrench螺钉扳手;活动扳手•screw-and-nut mechanism螺杆螺母传动机构•screw-and-nut steering gear螺杆螺母式转向器•screw-and-nut steering-gear螺杆螺母转向装置•screw-cap螺旋帽•screw-cutting lathe车螺纹车床•screw-cutting machine螺纹切削机床•screw-down压下机构•screw-driven螺旋传动•screw-driven planer螺杆传动刨床;丝杠式刨床•screw-driven planing machine螺杆传动刨床•screw-driven shaper螺杆传动牛头刨;丝杠式牛头刨床•screw-driven slotter丝杠式插床•screw-driver bit螺丝刀。
各种螺丝名称中英文对照
各种螺丝名称中英文对照六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝 HEX HEAD MACHINE BOL TS六角木牙螺丝 HEX LAG BOLTS四角螺丝 SQUARE HEAD BOLTST头螺丝 T HEAD BOLTS马车螺丝 CARRIAGE BOLTS环首螺丝 EYE BOLTS内六角孔螺丝 HEX SOCKET CAP SCREWS固定螺丝 SET SCREWS螺椿栓 STUD BOLTS螺旋椿 SCREW STUDS轮壳螺栓 WHEEL BOLTS翼形螺丝 WING SCREWS自攻螺丝 SELF TAPPING SCREWS自削螺丝 THREAD CUTTING SCREWS钻尾螺丝 SELF DRILLING SCREWS旋入螺丝 DRIVE SCREWS机械螺丝 MACHINE SCREWS木螺丝 WOOD SCREWS家具螺丝 FURNITURE SCREWS塑板螺丝 CHIPBOARD SCREWS墙用螺丝 DRYWALL SCREWS基础螺栓 FOUNDA TION BOLTSU型螺栓 U BOLTS勾头螺栓 HOOK BOLTS套挂螺丝 TOGGLE BOLTS突缘螺丝 FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝 CORTEN STEEL HEA VY HEX BOLTS扭矩控制螺栓 T.C.BOLTS高张力螺栓 HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合 SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓 BIG SIZE BOLTS不锈钢小螺丝 STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝 STAINLESS STEEL BOLTS。
螺丝类型中英文对照
六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS) 六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYWALL SCREWS基础螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝CORTEN STEEL HEAVY HEX BOLTS扭矩控制螺栓T.C.BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS)大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑胶螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽AUTOMOTIVE FAS TENERS航太用螺丝AEROSPACE FAS TENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FAS TENERS电梯螺丝ELEVATOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE WAY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEAVY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS 不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS。
螺丝产品名称和中英文对照
螺丝名称的中英文对照表
螺丝名称的中英文对照表常用英文单词及简写形式No. 单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread P T 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标47 ISO / 国际标准48 NFE / 法标49 GB / 国家标准50 Quality / 质量51 surface hardness 表面硬度52 product treatment 表面处理53 plating 电镀54 heat 热55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车用螺丝、轴心56 Screws And Shafts For Sewing Maching 针车用螺丝、轴心57 Socket Set Screws 止付螺丝58 Stainless Steel Coarse Thread Screws 不锈钢宽牙螺丝59 Stainless Steel High-Low Thread Screws 不锈钢高低牙螺丝60 Stainless Steel Machine Screws 不锈钢机械螺丝61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝62 Stainless Steel Self Tapping Screws 不锈钢螺丝class=a1>自攻螺丝63 Stainless Steel Thread Cutting Screws 不锈钢自削螺丝64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三角牙螺丝65 Steel Ceiling Anchors 插片壁虎66 Drop in Anchors 内迫壁虎67 Steel Hit Anchors 碳钢锤钉壁虎68 Steel Hex Coupling Nuts 碳钢六角螺帽69 Wedge Anchors 强力车修壁虎70 Cut Anchors 外迫壁虎71 Chemical Anchors 化学壁虎72 Heavy Duty Expansion Anchors 不锈钢重载胀栓73 Tie Wire Anchors 鱼眼壁虎企眼长螺帽74 Hammer Drive Anchors 锌合金打入式壁虎75 Strut Nuts 弹簧螺帽76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列77 Nylon Frame Anchors or Metalframe Anchors 门窗、地板专用壁虎78 Hollow Wall Anchors 石膏板中空壁虎79 Sleeve Anchors 套管式壁虎80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打入式壁虎鱼形尼龙壁虎81 Hit Anchors 强力式锤钉壁虎82 Bolt Anchors 电梯壁虎83 Heavy duty anchors 重载壁虎84 Loxin Masonry Anchors 两片夹85 Set Bolts 定位螺栓86 Short Strap Anchors 长型兰花夹87 Drop in Setting Tools 工具棒88 Elephant foot anchors 象脚壁虎89 Concrete Insert 水泥预埋件90 Drop in Anchor with Lip 翻边胀轴91 Legs Drywall Anchors 冲件92 Hex Cap Nuts 六角盖头螺帽93 Hex Serrated Nuts 六角锯齿螺帽94 Hex Flange Nuts 六角轮缘螺帽95 Hex Coupling Nuts(High Nuts) 高脚螺帽96 Round Nuts 圆螺帽97 Square Nuts 四角螺帽98 Pipe Nuts 管用螺帽99 Wheel Nuts 轮壳螺帽100 Wing Nuts 蝶型螺帽101 U Nuts U形螺帽102 T Nuts T形螺帽103 Eye Nuts 环首螺帽104 Kep Nuts 齿形螺帽105 Clinch Nuts 齿花螺帽106 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽107 Weld Nuts 焊接螺帽108 Heigh Strength Nuts 高张力螺帽109 Structural Nuts 建业用螺帽110 Stainless Steel Nuts 不锈钢螺帽111 Brass Nuts 铜螺帽112 Aluminum Nuts 铝螺帽113 Alloy Steel Nuts 合金钢螺帽114 Heavy Duty Wheel Hub Nuts 重型车螺帽115 Acorn Cap Nuts 铁器焊接袋帽116 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽117 Anchor Nuts 壁虎螺帽118 Big Size Nuts 大尺寸螺帽119 Closed End Acorn Nuts 铁盖袋帽120 Conical Washer Nuts 盘形华司螺帽121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽123 Flat Waser Nuts 平面华司螺帽124 Hex Slotted Nut 六角割沟螺帽125 Self-Locking Nuts 自锁螺帽126 Sliding Nuts 制止螺帽127 Sln Self-Locking Nuts Sln-自动防松螺帽128 Special Nuts 其它特殊螺帽129 Spring Nuts 弹簧螺帽130 Stainless Steel Flange Nuts 不锈钢突缘螺帽131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽132 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽133 Stainless Steel Hex Nuts 不锈钢六角螺帽134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽135 Hex Nuts 普通六角螺帽136 Heavy Hex Nuts 六角重型螺帽137 Hex Jam Nuts 薄型螺帽138 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽139 Hex Machine Screw Nut 机械螺丝用六角螺帽140 Hex Head Cap Screws(Hex Bolts) 六角螺丝(栓)141 Hex Head Machine Bolts 六角机械螺丝142 Hex Lag Bolts 六角木牙螺丝143 Square Head Bolts 四角螺丝144 Carriage Bolts 马车。
螺丝名词中英文对照
38 internal 39 external 40 thickness 41 length 42 hole 43 Metric 44 DIN 45 ANSI 46 JIS
简写 scr nut wash hd thre coat riv stdoff driv hexa tooth lck spr wave pitch PT PT FT silv cone Eco TF self tapp pin Shaf St SS Bras(Cu) AL Rub mech scr SEM Scr material GD Finish Point Clam
螺丝名词中英文对照
来自--参考资料 （作者:参考资料 ） 发布时间 2006-2-14 21:32:41
No.
单词 1 screw 2 nut 3 washer 4 head 5 thread 6 coating 7 rivet 8 standoff 9 driver 10 hexagon 11 tooth 12 lock 13 spring 14 wave 15 pitch 16 partial thread 17 PT 18 Full Thread 19 silver 20 cone 21 Eco-syn 22 Thread Forming 23 Self Tapping 24 pin 25 shaft 26 steel 27 stainless steel 28 Brass(Cu) 29 Aluminum 30 Rubber 31 machine screw 32 SEM screw 33 Material 34 Grade 35 Finish 36 Point 37 Clamp
螺丝产品中英文对照
螺丝产品名称中英文对照作者: nancy 查看次数: 1432 发表时间: 2006/7/12 07:51 【论坛浏览】螺丝产品名称中英文对照(螺丝螺)螺丝产品名称中英文对照(螺丝螺)六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS) 六角机械螺丝HEX HEAD MACHINE BOLTS 六角木牙螺丝HEX LAG BOLTS 四角螺丝SQUARE HEAD BOLTS T头螺丝 T HEAD BOLTS 马车螺丝CARRIAGE BOLTS 环首螺丝EYE BOLTS 内六角孔螺丝HEX SOCKET CAP SCREWS 固定螺丝SET SCREWS 螺椿栓STUD BOLTS 螺旋椿SCREW STUDS 轮壳螺栓 WHEEL BOLTS 翼形螺丝WING SCREWS 自攻螺丝SELF TAPPING SCREWS 自削螺丝 THREAD CUTTING SCREWS 钻尾螺丝SELF DRILLING SCREWS 旋入螺丝DRIVE SCREWS 机械螺丝MACHINE SCREWS 木螺丝WOOD SCREWS 家具螺丝FURNITURE SCREWS 塑板螺丝CHIPBOARD SCREWS 墙用螺丝DR Y WALL SCREWS 基础螺栓FOUNDATION BOLTS U型螺栓U BOLTS 勾头螺栓HOOK BOLTS 套挂螺丝TOGGLE BOLTS 突缘螺丝FLANGE BOLTS 轨道螺栓(鱼尾螺丝) TRACK BOLTS 耐候钢螺丝CORTEN STEEL HEAVY HEX BOLTS 扭矩控制螺栓 T.C.BOLTS 高张力螺栓HIGH STRENGTH BOL TS 剪力钉(焊接螺丝) WELDING STUDS 螺丝附华司组合 SCREWS AND WASHERS ASSEMBLED(S EMS) 大尺寸螺栓BIG SIZE BOLTS 不锈钢小螺丝 STAINLESS STEEL SHEET METAL SCREWS 不锈钢大螺丝STAINLESS STEEL BOLTS 铜螺丝BRASS SCREWS 铝螺丝 ALUMINUM SCREWS 合金钢螺丝ALLOY STEEL SCREWS 电子螺丝ELECTRONIC SCREWS 微小精密螺丝MICRO SCREWS 塑胶螺丝PLASTIC SCREWS 复合材料用螺丝 PAR TICLE BOARD SCREWS 钛合金螺丝 TI TANIUM ALLOY BOLTS 钛、锆、钼、铌等螺丝、零件、材料 TI,ZR,MO,NB PARE METAL BOLTS PAR TS 拇指螺丝THUMB SCREWS 双头牙螺丝DOUBLE END SCREWS HANGER BOLT 车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS 航太用螺丝AEROSPACE FASTENERS 飞机特殊扣件 SOURCE CON TROL BOLTS 拉栓BLIND BOLTS 面板螺丝PANEL FASTENERS 电梯螺丝ELEVATOR BOLTS 四角头固定螺丝SQUARE SET SCREWS 大头马车螺丝 STEP BOLTS 单向螺丝 ONE WAY LAG SCRE WS 管夹螺丝HOSE CLAMP SCREWS 不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCR EWS 不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS 铰链螺丝HINGE SCREW S 货柜螺丝CONTAINER SCREWS 复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS 三角牙螺丝TRILOBULAR THREAD SCREWS 高低牙螺丝HIGH LOW SCREWS 夹板用螺丝PAR TICLE B OARD SCREWS 马桶螺丝 TOILET CLOSET BOLTS 特长螺丝SPECIAL LONGER SCREWS 建业螺丝BUILDING FASTENERS 不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS 其它特殊螺丝SPECIAL SCREWS OR BOLTS 不锈钢特殊螺丝 SPECIAL STAINLESS STEEL SCREWS 宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS 链带螺丝COLLATED SCREWS 水泥螺丝CONCRE TE SCREWS 板模螺丝CONSTRUCTION BOLTS 涞□萁z DIE CAST WING SCREWS; ZINC ALLOY 重型车螺丝HEAVY DUTY WHEEL HUB BOLTS 内六角固定螺丝HEX SOCKET SET SCREWS 复合材料用螺丝（夹板用）PAR TICLE BOARD SCREWS 犁壁螺丝PLOW BOLTS 机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAF TS FOR SEWING MACHING 止付螺丝SOCKET SET SCREWS 不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS 不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS 不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS 不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS 不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS 不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS 不锈钢三角牙螺丝 STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS 套挂螺栓及螺丝 TO GGLE BOLTS 钛合金膨胀螺丝 TITANIUM ALLOY EXPANSION BOLTS关于螺丝词汇的中英文对照六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRATED NUTS六角轮缘螺帽HEX FLANGE NUTS高脚螺帽HEX COUPLING NUTS(HIGH NUTS)圆螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS轮壳螺帽WHEEL NUTS蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽 T NUTS环首螺帽EYE NUTS齿形螺帽KEP NUTS齿花螺帽CLINCH NUTS耐候钢六角重型螺帽CORTEN STEEL HEAVY HEX NUTS焊接螺帽WELD NUTS高张力螺帽HEIGH STRENGTH NUTS建业用螺帽STRUCTURAL NUTS不锈钢螺帽STAINLESS STEEL NUTS铜螺帽BRASS NUTS铝螺帽ALUMINUM NUTS合金钢螺帽ALLOY STEEL NUTS重型车螺帽HEAVY DUTY WHEEL HUB NUTS铁器焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREVAILING TORQUE TYPE NUTS壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司螺帽CONICAL WASHER NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS突缘尼龙盖帽FLANGE NYLON INSER T LOCK NUTS平面华司螺帽FLAT WASER NUTS六角割沟螺帽HEX SLOTTED NUT自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自动防松螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS弹簧螺帽SPRING NUTS不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角轮缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS。
螺丝品名代号中英文对照表
SAW SLOT
14
N
#2 SQUARE RECESS（UAB）
2号四角孔（UAB）客户
#2 SQ
15
O
#0 SQUARE RECESS
0号四角孔
#0 SQ
16
P
#2 PHILLPS RECESS
2号十字孔
#2 PHIL
17
Q
#2 SQUARE RECESS
2号四角孔
#2 SQ
18
R
MFGR MARKS “TY”
SELF TAPPING SCREWS DIN STANDARD
自攻螺丝（DIN标准）
S/T/S TO DIN
25
Y
DRYWALL SCREWS墙用螺丝（MM） NhomakorabeaD/W/S
26
Z
SELF DRILL SCREWS
钻尾螺丝（IN+MM）
S/D/S
27
0
METAL NEOPRENE WASHER
铁华司+橡胶华司
澳洲墙用螺丝
DRYWALL SCREWS
11
K
SELF TAPPING SCREWS
澳洲攻牙螺丝
SELF TAPPING SCREWS
12
L
SELF DRILL SCREWS（TEK SCREW）
钻尾螺丝（IN）
S/D/S
13
M
MACHINE SCREWS
机械螺丝（IN）
M/S
14
N
NUTS
螺帽（IN）
头记“TY”
WITH MFGR MARKS “TY“
19
S
STRUCK SLOT
关于螺丝的中英文对照
(浏览56次)No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝（机牙螺丝）32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种) B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出)A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical properties unified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle) 门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts) 圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts 普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts 扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws 不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws 铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws 其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws 犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts 壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts 锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine 气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils ForBolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings 中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs 螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching 止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws 不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread ScrewsMFNI 克叻MFZN 锌Na tural 本色Nikel 叻B-TITE 三角身自攻B型牙P-TITE II 三角身自攻P型双丝牙Nylock 耐落No Nylock 无耐落Case hardness：HV430-530 表面硬度：HV430-530Core hardness：HV210-410 心部硬度：HV210-410Case depth：0.04-0.10mm 渗碳层厚度:0.04-0.10mmProduct compliance with RoHS requirement 产品符合RoHS要求。
螺丝名词中英文对照及简写
No. 单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
摘要：螺丝名词中英文对照No. 单词简写中文 1 screw scr 螺丝 2 nut nut ... 螺丝名词中英文对照No.单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial P T 半螺纹thread17 PT PT 一种螺纹形式18 Full FT 全螺纹Thread19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread TF 自攻螺纹Forming23 Self self tapp 自切屑螺纹Tapping24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless SS 不锈钢steel28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine mech scr 机制螺丝screw32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标紧固件类英语词汇白铁盖螺丝A2(18-8)CAP SCREWS水平调整螺丝ADJUSTED LEVELING SCREWS航太扣件AEROSPACE FASTENERS合金钢螺丝(栓) ALLOY STEEL SCREWS (BOLTS)铝螺丝ALUMINUM SCREWS车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS复含材料钻尾螺丝BI-METAL SELF DRILLING SCREWS 大尺寸螺丝BIG SIZE BOLTS公母螺丝组BINDER POST & SCREW SET拉栓BLIND BOLTS铜螺丝(栓) BRASS SCREWS (BOLTS)建筑螺丝BUILDING FASTENERS建筑膨涨螺丝BUILDING WALL ANCHOR半圆头六角孔螺丝BUTTON HEAD SOCKET CAP SCREWS 马车螺丝CARRIAGE BOLTS活动轮螺丝附件CASTORS FITTINGS塑板螺丝CHIPBOARD SCREWS快速钉紧螺丝及螺帽CLINCH STUDS & NUTS挤压扣件CLINCHING FASTENERS齿花扣件CLINCHING PARTS宽牙螺丝COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模扣件CONSTRUCTION FASTENERS货柜螺丝CONTAINER SCREWS耐候钢螺丝CONTEN STEEL HEAVY HEX BOLTS鱼尾螺丝CONTEN STEEL OVAL NECK TRACK BOLTS双刀螺丝CUTTER SCREWS匣板螺丝DECK SCREWS锌蝶螺丝DIE CAST WING SCREWS;ZINC ALLOY双头牙螺丝DOUBLE END SCREWS，HANGER BOLT旋锁螺丝DRIVE LOCK SCREWS旋入螺丝DRIVE SCREWS墙用螺丝DRYWALL SCREWSEJOT DELTA PT SCREWSEJOT PT SCREWS电子螺丝ELECTRONIC SCREWS电梯螺丝ELEVATOR BOLTS欧洲螺丝EURO SCREWS环首螺丝EYE BOLTS冈山头螺丝FILLISTER SCREWS鳍头螺丝FIN NECK ROUND HEAD BOLTS管配件接头FITTING FASTENERS (CONNECTORS)突缘螺丝FLANGE BOLTS (SCREWS)平头六角孔螺丝FLAT HEAD SOCKET CAP SCREWS平纺螺丝FLAT PAN HEAD SCREWS地板螺丝FLOORING PANEL SCREWS基础螺丝FOUNDATION BOLTS框架支撑螺丝FRame ANCHOR-LAG ROUND SCREWS家俱螺丝FURNITURE SCREWS (CONNECTING BOLTS)重型车螺丝、螺帽HEAVY DUTY WHEEL HUB BOLTS & NUTS六角螺丝(栓) HEX HEAD CAP SCREWS (HEX BOLTS)六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS等高螺丝HEX SOCKET HEAD SHOULDER SCREW薄头强力螺丝HEX SOCKET LOW HEAD CAP SCREW内六角固定螺丝HEX SOCKET SET SCREWS华司头机械螺丝HEX WASHER HEAD MACHINE SCREWS高低牙螺丝HIGH LOW THREAD SCREWS高张力螺丝HEX SOCKET HEAD SHOULDER SCREW铰链螺丝HINGE SCREWS勾头螺栓HOOK BOLTS管夹螺丝HOSE CLAMP SCREWS哈克钉HUCK BOLTS旋锁螺丝KTX LOCKING RECESS SCREWS机械螺丝MACHINE SCREWSMDF螺丝MDF SCREWS微小精密螺丝MICRO SCREWS钼六角螺丝MO HEX HEAD CAP SCREWS钼NC螺丝MO NC FASTENERS钼螺帽MO NUTS镍合金螺丝MONEL FASTENERS多冲程螺丝MULTI-STAGE SCREW & PARTS利革钉NYLON PLUG & SCREWS单向螺丝ONE WAY LAG SCREWS枋头中心螺丝PAN HEAD CENTER BOLTS面板螺丝PANEL FASTENERS复合材料用螺丝(夹板用) PARTICLE BOARD SCREWS贯穿螺丝PENETRATE SCREWS十字四角复合螺丝PH+SQ COMBINATION SCREWS塑胶螺丝PLASTIC SCREWS犁壁螺丝PLOW BOLTS特殊精密螺丝PRECISION AXIS AND SPECIAL FASTENERS卷带螺丝ROLL COLLATED SCREWS屋顶螺丝ROOFING SCREWS螺旋椿SCREW STUDS机(踏)车用螺丝.轴心SCREWS & SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝.轴心SCREWS & SHAFTS FOR SEWING MACHINE螺丝附华司组合SCREWS & WASHERS ASSEMBLED (SEMS)安全螺丝SECURITY SCREWS钻尾螺丝SELF DRILLING SCREWS自攻螺丝SELF TAPPING SCREWS固定螺丝SCREWS & SHAFTS FOR SEWING MACHINE剪力钉SHEAR CONCRETE STUD束肩螺丝(栓) SHOULDER SCREWS (BOLTS)一字沟槽固定螺丝SLOTTED SET SCREWS止付螺丝SOCKET SET SCREWS飞机特殊扣件SOURCE CONTROL BOLTS特殊涂装螺丝SPECIAL COATING SCREWS特长螺丝SPECIAL LONGER SCREWS特殊材质螺丝SPECIAL MATERIAL SCREWS特殊螺丝SPECIAL SCREWS OR BOLTS特殊防松螺丝SPECIAL SELF-LOCKING SCREWS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS特殊割尾螺丝SPECIAL THREAD CUTTING SCREWS四角螺丝SQUARE HEAD BOLTS四角头固定螺丝SQUARE HEAD SET SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS不锈钢塑板螺丝STAINLESS STEEL CHIPBOARD SCREWS不锈钢粗牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢旋入螺丝STAINLESS STEEL DRIVE SCREWS不锈钢平头内六角孔螺丝STAINLESS STEEL FLAT HEAD SOCKET CAP SCREWS 不锈钢六角螺丝STAINLESS STEEL HEX HEAD CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET SET SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢小螺丝STAINLESS STEEL SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢SEMS 螺丝STAINLESS STEEL SEMS SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢牙条棒STAINLESS STEEL THREAD ROD不锈钢三角牙螺丝STAINLESS STEEL TRIANGULAR SCREW THREAD不锈钢木螺丝STAINLESS STEEL WOOD SCREWS卡锁壁虎STEEL LOCKING ANCHOR大头马车螺丝STEP BOLTS螺桩栓STUD BOLTST头螺丝T HEAD BOLTS扭矩控制螺栓T.C. BOLTS (TENSION CONTROL BOLTS)自削螺丝THREAD CUTTING SCREWS牙条棒THREAD ROD姆指螺丝THUMB SCREWS钛合金自行车螺丝TITANIUM -6AL –4R ALLOY FASTENERS钛合金螺丝TITANIUM ALLOY BOLTS钛六角螺丝TITANIUM HEX HEAD CAP SCREWS (HEX BOLTS)钛NC螺丝TITANIUM NC FASTENERS钛止付螺丝TITANIUM SET SCREWS钛内六角孔螺丝TITANIUM SOCKET CAP SCREWS钛牙条TITANIUM THREAD ROD套挂螺丝TOGGLE BOLTS套挂螺栓及螺丝TOGGLE BOLTS & ACOUSTICAL LAG (SCREWEYE) 马桶螺丝TOILET CLOSET BOLTSTORX SCREWS TORX SCREWS轨道螺栓(鱼尾螺丝) TRACK BOLTS三角牙螺丝TRIANGULAR SCREWS THREADU型螺栓U BOLTS直立轴螺丝VERTICAL SHAFT SCREWS焊接螺丝WELD STUDS，SCREWS，BOLTS焊点螺丝WELD STUDS SCREWS轮毂螺栓WHEEL BOLTS车轮轴螺丝，螺帽WHEEL HUB BOLTS AND NUTS窗户螺丝WINDOW SCREWS翼形螺丝WING SCREWS木螺丝WOOD SCREWS锆螺丝ZR FASTENERSSET SCREWS SET SCREWSHIGH STRENGTH BOLTS HIGH STRENGTH BOLTS铁盖焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREVAILING TORQUE TYPE NUTS 合金钢螺帽ALLOY STEEL NUTS铝螺帽ALUMINUM NUTS壁虎螺帽ANCHOR NUTS圆柱帽BARREL NUTS (CROSS DOWEL)大尺寸螺帽BIG SIZE NUTS铜螺帽BRASS NUTS四角多用途螺帽CAGE NUTS袋帽CAP NUTS城堡螺帽CASTLE NUTS齿花螺帽CLINCH NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司+袋帽螺帽CONICAL WASHER AND CAP NUTS盘形华司螺帽CONICAL WASHER NUTS耐候钢六角重型螺帽CORTEN STEEL HEAVY HEX NUTS长螺帽COUPLING NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS碟锁防松脱螺帽DISK-LOCK NUTS企眼螺帽EYE COUPLING NUTS环首螺帽EYE NUTS突缘尼龙螺帽FLANGE NYLON INSERT LOCK NUTS平面华司螺帽FLAT WASHER NUTS齿轮GEARS六角重型螺帽HEAVY HEX NUTS六角盖头螺帽HEX CAP NUTS六角突缘螺帽HEX FLANGE NUTS薄型螺帽HEX JAM NUTS薄型电子六角螺帽HEX JAM NUTS (FOR ELECTRONIC) 机械螺丝用六角螺帽HEX MACHINE SCREW NUT普通六角螺帽HEX NUTS六角锯齿螺帽HEX SERRATED NUTS双头内牙螺帽HEX (REDUCER )COUPLING NUTS高螺帽HIGH NUTS高张力螺帽HIGH STRENGTH NUTS内外牙螺母(拉帽) INSERT NUTSJCN NUTS JCN NUTS齿形螺帽KEP NUTS防松螺帽LOCK NUTS长螺帽LONG NUTS机车用螺帽NUTS FOR MOTORCYCLE面板螺帽NUTS PLATE尼龙袋帽NYLON CAP INSERT LOCK NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS马桶螺帽OPEN END ACORN NUTS卡车轮胎螺帽OUTER CAP NUTS管用螺帽PIPE NUTS塑胶螺帽PLASTIC NUTSPOP NUTS POP NUTS抑制螺帽PREVAILING TORGUE NUT快速扣件PUSH NUT FASTENERS长方形螺帽(薄型) RECTANGLE JAM NUTS长方四角螺帽RECTANGLE SQUARE NUTS圆螺帽ROUND NUTS自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自锁防松螺帽SLN SELF-LOCKING NUTS沟槽螺帽SLOTTED NUTS特殊螺帽SPECIAL NUTS特殊轮毂螺帽SPECIAL WHEEL NUTS弹簧螺帽SPRING NUTS薄型四角螺帽SQUARE JAM NUTS四角螺帽SQUARE NUTS不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角突缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS 不锈钢六角重型螺帽STAINLESS STEEL HEAVY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢螺帽STAINLESS STEEL NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS不锈钢四角螺帽STAINLESS STEEL SQUARE NUTS建筑用螺帽STRUCTURAL NUTST形螺帽T NUTS塑胶品之埋植铜，铝螺帽THREADED INSERTS FOR PLASTIC INJECTION MOULDINGS钛螺帽TITANIUM NUTS压边螺帽+盘形华司组合TOP LOCK NUT WITH CONICAL WASHER ASSEMBLEU形螺帽U NUTS焊接螺帽WELD NUTS轮毂螺帽WHEEL NUTS蝶形螺帽WING NUTS锌压铸螺帽ZINC DIE CASTING NUTS铝钉ALUMINUM NAILS马达轴承轴心组件BEARING SHAFT（MOTOR）轴承轴心BEARING SHAFT开口铆钉BIFURCATED RIVETS长形拉帽（长型螺帽）BINDER POSTS（ANCHOR NUTS）拉帽BLIND NUTS (RIVET NUTS)拉钉BLIND RIVETS电梯壁虎BOLT ANCHOR金属粘着橡胶华司（双层华司）BONDED WASHERS铜钉BRASS NAILSC型扣环C-RINGS小眼钉CEILING HANGER化学壁虎CHEMICAL STUD实心梢CLEVIS PINS & STRAIGHT PINS弹片CLIPS卷钉COIL NAILS冷锻零件COLD FORMING PART开口梢COTTER PINS洋钉钩CUP HOOKS弧型华司CURVED WASHER外迫壁虎CUT ANCHOR插梢DOWEL PIN捶钉DRIVE RIVET壁虎DROP IN ANCHORE型环E-RINGS膨胀螺栓EXPANSION ANCHOR BOLTS难眼钉EYELETS RIVETS门钩GATE HOOKS插沟销GROOVED PINS有槽钢钉GROOVED STEEL NAILS火药钉GUNPOWDER NAILS壁钩HARDWALL HANGERS双片夹壁虎HEAVY DUTY SHIELD ANCHORR型梢HITCH PINS（SNAP PINS）空心钉HOLLOW RIVETS洋钉IRON NAILSJ钩J HOOKK.D. FITTING K.D. FITTING闩锁LATCHES & KEEPER ASSEMBLEDS多冲程铆钉MULTI-STAGE RIVERS锤钉壁虎NAIL IN ANCHOR尼龙壁虎NYLON (METAL) FRame ANCHOR塑胶华司NYLON WASHERS其他特殊铆钉OTHER SPECIAL RIVETS样品钩PEGBOARD HOOK吊图钩PICTURE HANGERS梢PINS各式管夹，管束PIPE HANGER管塞PIPE PLUG塑胶壁虎PLASTIC NYLON ANCHORSPOP拉钉系列产品POP RIVETS快速插销QUICK RELEASE PINSR型扣环R-RINGS扣环RINGS铆钉RIVETS圆棒铁钉ROUND IRON NAILST型铁钉ROUND IRON TAPE T NAIL圆棒钢钉ROUND STEEL NAILST型钢钉ROUND STEEL TAPE T NAILSU型钢钉ROUND STEEL TAPE U NAILS橡胶华司RUBBER WASHERSS钩S HOOKSS型扣环S-RINGS螺旋铝钉SCREW ALUMINUM NAILS螺旋环(洋眼) SCREW EYES螺旋钩及螺旋圈SCREW HOOK & SCREW RINGS 螺丝钩SCREW HOOKS螺旋铁钉SCREW IRON NAILS螺旋钢钉SCREW STEEL NAILS中空铆钉SEMI-TUBULAR RIVET套管壁虎SLEEVE ANCHOR实心铆钉SOLID RIVETS特殊华司SPECIAL WASHERS快速铆接扣件SPEED RIVETING开叉钉SPLIT DRIVE ANCHORS弹簧梢SPRING PIN弹簧华司SPRING WASHERS弹簧蝴蝶夹SPRING WINGS折钉SQUARE HOOKS不锈钢钢钉STAINLESS STEEL NAILS不锈钢中空钉STAINLESS STEEL SEMI-TUBULAR RIVET不锈钢斜纹钉STAINLESS STEEL SLANTING STRIPES NAILS 不锈钢华司STAINLESS STEEL WASHERS钢铁钉STEEL & IRON NAILS钢钉STEEL NAILSL型钢钉STEEL TAPE L NAILS铁马钩STORAGE HOOK吸盘钩SUCTION HANGERS兰花钩SWAG HOOKS三角吊钩SWIVEL LOOP HANGERS地毯钢钉TACKED IRON NAILS搓牙铁钉THREAD NAILS大眼钉TIE WIRE SPADE STUD钛合金铆钉TITANIUM ALLOY RIVETS钛合金膨涨螺丝TITANIUM ALLOY EXPANSION BOLTS钛华司TITANIUM WASHERS齿型华司TOOTH LOCK WASHERS管形铆钉TUBULAR RIVETS双向迫紧器TURNBUCKLE节牙钢钉W/STRIP STEEL NAILS华司WASHERS波浪型华司WAVE WASHER拉涨壁虎WEDGE ANCHOR线圈WIRE锌合金壁虎ZINC ALLOY FRame ANCHOR螺丝，螺帽，五金，DIY扣件ALL KINDS OF PACD AGING SERIES 合金钢工具ALLOY STEEL TOOLS电子手把HANDLES FOR ELECTRONIC DEVICES六角板手HEXAGON KEYS螺丝起子POWER BIT螺丝起子SCREWDRIVER BIT电动螺丝起子AUTOFEED SCREWDRIVER工具套筒组件SOCKET SETS套筒SOCKETS板手WRENCH自动炼带螺丝枪AUTOFEED SCREW DRIVER合金钢线材盘元ALLOY STEEL WIRE ROD铝合金锭ALUMINUM ALLOY球状化线材ANNEALING WIRE & ROD黑铁丝BLACK WIRE黄铜棒线BRASS WIRE & ROD磨光棒钢BRIGHT STEEL BAR (HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD镀锌铁线GALVANIZED STEEL WIRE线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHOR BRONZE WIRE各种表面处理用喷砂材料SAND BLASTING MATERIALS不锈钢条棒STAINLESS STEEL BAR (ROUND/HEX/SQUARE)不锈钢冷锻线材STAINLESS STEEL COLD HEADING WIRE不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE不锈钢网线STAINLESS STEEL NET WIRE不锈钢特殊线STAINLESS STEEL SPECIAL WIRE不锈钢弹簧线STAINLESS STEEL SPRING WIRE不锈钢线材STAINLESS STEEL WIRE不锈钢线材及盘元STAINLESS STEEL WIRE & ROD棒钢STEEL BAR(HEX/ROUND/SQUARE)钛、锆、钼、铌等螺丝、零件、材料TI、ZR、MO、NB PARE METAL BOLTS PARTS锌合金锭ZINC ALLOY立体/平面雕刻机3D DIE-SINKING MACHINE/ENGRAVING MACHINE转回90度辗线头机90°REVOLVING WIRE TWISTING MACHINE干燥机AIR DRYER气动拉钉机AIR RIVETER铝不锈钢六角头螺栓，低合金熔解热处理炉ALUMINUM & LOW ALLOY MELTING FURNACE铝散热器烧焊热处理炉ALUMINUM BRAZING FURNACE FOR ALUMINUM CONDENSER不锈钢线材连续式光辉热处理退火炉ANNEALING FURNACE SPECIALLY FOR STAINLESS WIRE小型脱油机ANTI-OIL MACHINE自动包装机AUTOMATIC PACKING MACHINE螺丝自动检查设备AUTOMATIC SCREW SORTING MACHINE自动送锁螺丝机AUTOMATIC SCREWING MACHINE螺丝割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE螺丝制造成型机械AUTOMATIC TRIMMING MACHINE箱式渗碳氮化炉BATCH TYPE CARBURIZING & MITRIDING FURNACE钟罩式退火(球化)炉BELL TYPE SPHEROIDIZING ANNEALING FURNACE拉帽成型机BLIND NUT FORMERS拉钉打头机BLIND RIVET HEADING MACHINE螺丝(栓)成型机BOLT FORMERS螺丝、螺帽成型机BOLT FORMERS，NUT FORMERS六角头螺栓c级沉头内六角螺栓，HEADERS螺栓模BOLT HEADING DIES螺丝、螺帽热处理BOLT，NUT & SCREWS HEAT TREATMENT螺丝、螺帽热处理炉BOLT六角螺栓，NUT & SCREWS HEAT TREATMENT FURNACES 圆剪式打头机BUSH CUT-OFF HEADING MACHINE圆剪式空心打头机BUSH CUT-OFF HOLLOW HEADING MACHINE主模CARBIDE DIES剪模CARBIDE QUILLS不锈钢螺丝，扣件连续式光辉调质淬火炉CARBURIZING FURNACE FOR STAINLESS FASTENER球状化电气炖炉CARBURIZING FURNACE，VACUUM & BELL TYPE FURNACE流气式箱型炉(箱式，坑式，台车式，连续式) CIRCULATION FURNACE (BOX六角头螺栓尺寸沉头内六角螺栓，PIT，TRUCK，CONTINUOUS TYPE)CNC电脑雕刻机CNC ENGRAVING MACHINE卷钉制造机COIL NAIL COLLATOR连续式光辉渗碳六角螺栓，淬火六角螺栓六角头螺栓标记示例外六角螺栓，回火炉CONTINUOUS BRIGHT CARBURIZING & HARDENING FURNACE连续式光辉渗碳淬火炉CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE连续式光辉调质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中六角头螺栓标准，高热镀锌光辉连续炉CONTINUOUS BRIGHT HEAT TREAT FURNACE连续式光辉热处理炉(不锈钢，硬焊) CONTINUOUS BRIGHT TREATMENT (FOR STAINLESS，BRAZING)连续式光辉热处理炉CONTINUOUS TYPE BRIGHT HEAT TREATMENT FURNACE耐腐蚀表面处理炉(耐炼) CORROSION RESISTANCE OF SURFACE TREATMENT FURNACE剪刀(螺丝模) CUT-OFF KNIVES集尘设备CYCLONE EQUIPMENT各种碳化钨制品设计制造DESIGN & MANUFACTURE OF TUNGSTEN CARBIDE PRODUCTS模具DIES & TOOLS钻尾模DRILL POINT DIES耐冲螺丝成型模具FASTENER FORMING DIES螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENTS’INSTRUMENTS精密过滤器FILTER滚沟牙板FLAT KNURLING DIES一般线材六角头螺栓标准，盘元，退火炉GENERAL WIRE，WIRE ROD ANNEALING FURNACE手动拉钉钳HAND RIVETER倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE白铁针HEADER PUNCHES FOR STAINLESS BOLT三角六角头螺栓标记示例六角头螺栓尺寸，四角，六角针HEADER PUNCHES IN VARIOUS DRIVES(1)米字，一字，梅花，零号针HEADER PUNCHES IN VARIOUS DRIVES(2)一字六角边冲头HEADER PUNCHES IN VARIOUS DRIVES(3)螺丝打头机HEADING MACHINE六角冲针HEX PINS六角冲模HEX RECESS PUNCHES六角冲模HEX TRIMMING DIES螺丝制造高速搓牙机械HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感应加热炉HIGH，MEDIUM六角头螺栓标记示例，LOW FREQUENCY INDUCTION HEATER空心打头机HOLLOW HEADING MACHINE热锻造机HOT FORMER冲销KNOCKOUT PINS雷射/影像筛选机LASER/OPTICAL SORTING MACHINE FOR SCREWS立式输送机LOADER机械螺丝牙板MACHINE SCREW THREAD ROLLING DIES PLATES螺帽用的冲具MANUFACTURE OF PUNCH MAKING BOLTS AND NUTS迷你成型机MINI-FORMERS铁钉滚牙机NAIL ROLLING MACHINE铁钉模具NAILS DIE成品自动收线机NON-STOP COILER精抽自动收线机NON-STOP COILER (SKINPASS)螺帽模NUT FORMING DIES螺帽成型机NUTS FORMERS螺帽攻牙机NUTS TAPPING MACHINE特殊零件成型机PARTS FORMING MACHINE脚踏板系列自动组立专用机PEDAL AUTOMATIC ASSEMBLING MACHINE十字四角复合针PH+SQ COMBINATION PUNCHES四角十字冲模十字冲模PHILLIPS PUNCHES十字割沟冲模PHILLIPS SLOTTED PUNCHES冲针壳PIN HOLDERS锁用中心零件PINS TAILPIECE抛光机/磨光台POLISHING MACHINE手握式螺丝自动供给锁紧机PORTABLE SCREW-DRIVING MACHINE粉末治金烧结，黑化炉POWDER METALLURGY & STEAM TREATMENT FURNACE米字冲模POZI PUNCHES冲模PUNCH DIES冲子PUNCH PINS冲针冲床引伸模具PUNCHING DIES罗拉成型机ROLLERS FORMERSRX，DX瓦斯变成炉，AX 氨气分解炉RX，DX GAS GENERATOR，AX AMMO GAS GENERATOR盐浴式热处理炉SALT BATH HEAT TREATMENT FURNACE各式表面处专用喷砂机SAND BLASTING MACHINE FOR SURFACE TREATMENT螺丝自动组合华司机器SCREW & WASHER ASSEMBLY MACHINE FOR SEMS机(踏)车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE 螺丝夹尾模SCREWS TAIL POINT DIES钻尾螺丝成型机SELF-DRILLING SCREW FORMING MACHINE钻尾模具SELF-DRILLING SCREW MAKING DIES止付螺丝成型机SET SCREWS FORMERS梅花冲头SIX LOBE PUNCHES一字冲模SLOT PUNCHES套筒成型机SOCKETS FORMERS碳钢盘元，线材，球状化热处理退火炉SPHEROIDIZING ANNEALING FURNACE FOR STEEL WIRE一般线材，盘元，螺丝合金炖炉SPHEROIDIZING BRIGHT ANNEALING FURNACE球状化热理炉SPHEROIDIZING HEAT TREATMENT FURNACE四角孔针具SQ PUNCHES四角冲模SQUARE RECESS PUNCHES不锈钢钻尾螺丝割尾STAINLESS STEEL SELF DRILLING SCREW MILLED POINT钻子TAP攻牙机TAPPING MACHINE自攻螺丝牙板TAPPING SCREW THREAD ROLLING DIES PLATES螺丝攻、车刀、模具TAPS DIES & TOOLS铁氟龙(TEFLON)及珐琅烧付炉TEFLON COATING FURNACE搓牙机铁屑牙离装置THREAD CHIP SEPARATOR滚牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLATES螺丝搓手机THREAD ROLLING MACHINE精密油压滚牙机THREAD ROLLING MACHINES货物捆绑系统TIE DOWN HARDWARE弹簧机周边零件TOOLING PERIPHERAL COMPONENT OF SPRING MACHINE六角整头模TRIMMING DIES HEXAGON碳化钨模具TUNGSTEN CARBIDE DIEUNILOCK SELF-LOCKING AND SEAL-LOCKING UNILOCK SELF-LOCKING ANDSEAL-LOCKING FASTENERS电镀化学原料VARIOUS ELECTROPLATING CHEMICALS立式单双层连续伸线机VERTICAL TYPE SINGLE DECK WIRE DRAWING MACHINE温锻造机WARM FORMER伸线机WIRES DRAWER特殊铆合扣件COLLARS (A BLIND FASTENER FOR HUCK INTL)电器银接点CONTACT POINT螺丝DIY包装系列DIY SCREWS PACKING SERIES自攻螺纹衬套ENSAT THREAD INSERT螺丝、螺帽成型攻牙专用油FORMING & TAPPING OILS FOR BOLTS & NUTS FORMERS铰链HINGES热浸镀锌螺丝沉头内六角螺栓螺帽HOT DIP GALVANIZING。