PBT+PC 基础创新塑料 553 物性表

玻纤增强型PC PBT混合物物性表

宝瑞塑胶原料有限公司
概述材料，玻璃纤维增强型聚碳酸酯/聚对苯二甲酸丁二醇酯（PBT）混合
类别：热塑性聚合物聚碳酸酯（PC），聚碳酸酯/聚对苯二甲酸丁二酯（PBT）混合，玻璃纤维增强材质说明：此属性数据MatWeb的数据库中类似的材料类别“聚碳酸酯/聚对苯二甲酸乙二醇酯（PBT）混合，玻璃纤维增强的总结”。

报告的每个属性的值范围是适当MatWeb的条目的最小值和最大值。

的注释报告的平均值，用于计算平均值的数据点的数目。

值不一定是典型的任何特定的品位，尤其是不太常见的价值观和那些可以受影响最严重的添加剂或加工方法。

PBT+GF 物性表

PBT,30%glass fibres,injection moulding,flame retardantISO Shortname:ISO 7792-1-PBT,GFHMR,09-110,GF30;ISO 1043-PBT GF FR(17)PropertyTest ConditionUnitStandardguide valueRheological properties C Melt volume-flow rate 260°C;5kgcm³/(10min)ISO 1133-137C Molding shrinkage,parallel 60x60x2;250°C /WZ 80°C;600bar%ISO 294-40.3C Molding shrinkage,transverse 60x60x2;250°C /WZ 80°C;600bar%ISO 294-40.9Post-shrinkage,parallel 60x60x2;120°C;4h %ISO 294-40.1Post-shrinkage,transverse60x60x2;120°C;4h%ISO 294-40.1Mechanical properties (23°C/50%r.h.)C Tensile modulus 1mm/min MPa ISO 527-1,-211500C Tensile Stress at break 5mm/min MPa ISO 527-1,-2125C Tensile Strain at break 5mm/min %ISO 527-1,-2 2.1C Charpy impact strength 23°C kJ/m²ISO 179-1eU 50C Charpy impact strength -30°C kJ/m²ISO 179-1eU 50C Charpy notched impact strength 23°C kJ/m²ISO 179-1eA <10C Charpy notched impact strength -30°C kJ/m²ISO 179-1eA <10Izod impact strength 23°C kJ/m²ISO 180-1U 45Izod impact strength -30°C kJ/m²ISO 180-1U 45Izod notched impact strength 23°C kJ/m²ISO 180-1A <10Izod notched impact strength -30°C kJ/m²ISO 180-1A <10Flexural modulus 2mm/min MPa ISO 178-A 10500Flexural strength2mm/min MPa ISO 178-A 200Flexural strain at flexural strength 2mm/min%ISO 178-A 2.6Ball indentation hardness N/mm²ISO 2039-1186C Puncture energy 23°C J ISO 6603-2 2.3C Puncture energy -30°C J ISO 6603-2 2.1C Puncture maximum force 23°C N ISO 6603-2669C Puncture maximum force -30°C NISO 6603-2649Thermal properties C Melting temperature10°C/min °C ISO 11357-1,-3225C Temperature of deflection under load 1.80MPa °C ISO 75-1,-2200C Temperature of deflection under load 0.45MPa °C ISO 75-1,-2220Vicat softening temperature50N;120°C/h °C ISO 306205C Coefficient of linear thermal expansion,parallel 23to 55°C 10-4/K ISO 11359-1,-20.2C Coefficient of linear thermal expansion,transverse 23to 55°C 10-4/K ISO 11359-1,-20.9C Burning behavior UL 940.38mm Class UL 94V-0C Burning behavior UL 940.8mm Class UL 94V-0C Oxygen indexMethod A%ISO 4589-232Pocan B 4239000000Page 1of 3PropertyTest Condition Unit Standard guide valueThermal conductivity23°CW/(m·K)ISO 83020.24Resistance to heat (ball pressure test)°C IEC 60695-10-2213Temperature index (Tensile strength)20000h °C IEC 60216-1155Halving interval (Tensile strength)°C IEC 60216-19.3Relative temperature index (Tensile strength)°C UL 746B 140Temperature index (Tensile impact strength)20000h °C IEC 60216-1130Halving interval (Tensile impact strength)°C IEC 60216-18.4Relative temperature index (Tensile impact strength)°C UL 746B 110Temperature index (Electric strength)20000h °C IEC 60216-1145Halving interval (Electric strength)°C IEC 60216-112Relative temperature index (Electric strength)°C UL 746B 125Glow wire test (GWFI)0.8mm °C IEC 60695-2-12960Glow wire test (GWIT)0.8mm °C IEC 60695-2-13725Glow wire test (GWIT) 1.6mm °C IEC 60695-2-13725Glow wire test (GWIT)3.0mm °CIEC 60695-2-13725Electrical properties (23°C/50%r.h.)C Relative permittivity 100Hz -IEC 60250 3.9C Relative permittivity 1MHz -IEC 60250 3.8C Electric strength1mm kV/mm IEC 60243-135C Comparative tracking index CTI Solution AV IEC 60112275Electrolytic corrosion RatingIEC 60426A/B 1Other properties (23°C)C Density kg/m³ISO 11831670Bulk densitykg/m³ISO 60800Processing conditions for test specimens C Injection molding-Melt temperature °C ISO 294250C Injection molding-Mold temperature °CISO 29480Processing recommendations Drying time circulating air dryer h -4-8Drying temperature circulating air dryer °C -120Residual moisture content %Acc.to Karl Fischer 0-0.02Melt temperature (Tmin -Tmax)°C -240-260Mold temperature°C-80-100C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO10350.Pocan B 4239000000Page 2of 3DisclaimerDisclaimer for sales productsThis information and our technical advice -whether verbal,in writing or by way of trials -are given in good faith but without warranty,and this also applies whereproprietary rights of third parties are involved.Our advice does not release you from the obligation to verify the information currently provided -especially that contained in our safety data and technical information sheets -and to test our products as to their suitability for the intended processes and uses.The application,use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and,therefore,entirely your own responsibility.Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery.Test valuesUnless specified to the contrary,the values given have been established on standardized test specimens at room temperature.The figures should be regarded as guide values only and not as binding minimum values.Kindly note that,under certain conditions,the properties can be affected to a considerable extent by the design of the mould/die,the processing conditions and the coloring.Processing noteUnder the recommended processing conditions small quantities of decomposition product may be given off during processing.To preclude any risk to the health and well-being of the machine operatives,tolerance limits for the work environment must be ensured by the provision of efficient exhaust ventilation and fresh air at theworkplace in accordance with the Safety Data Sheet.In order to prevent the partial decomposition of the polymer and the generation of volatile decomposition products,the prescribed processing temperatures should not be substantially exceeded.Since excessively high temperatures are generally the result of operator error or defects in the heating system,special care and controls are essential in these areas.LANXESS DEUTSCHLAND GMBH |D -51369LEVERKUSEN ©LANXESS DeutschlandGmbHPocan B 4239000000Page 3of 3。

PC基础创新EXL9330物性表

LEXAN™ EXL9330 resin聚碳酸酯SABIC Innovative Plastics产品说明Opaque PC-Siloxane copolymer with excellent processability. Non-chlorinated, non-brominated flame retardant product in most colors. UV-stabilized. UL rated f1/V-0/5VA.添加剂紫外线稳定剂阻燃性特性Chlorine Free 共聚物可加工性,良好无溴阻燃性RoHS 合规性RoHS 合规外观不透明加工方法注射成型物理性能额定值单位制测试方法比重 -- 1.18g/cm³ASTM D792 --1.19g/cm³ISO 1183 熔流率(熔体流动速率) (300°C/1.2 kg)10g/10 min ASTM D1238 溶化体积流率(MVR) (300°C/1.2 kg)9.00cm³/10min ISO 1133 收缩率内部方法流动 : 3.20 mm 0.40 到 0.80%内部方法横向流动 : 3.20 mm 0.40 到 0.80%内部方法吸水率 ISO 62 饱和, 23°C0.35%ISO 62 平衡, 23°C, 50% RH 0.15%ISO 62 室外适用性f1UL 746C硬度额定值单位制测试方法球压硬度 (H 358/30)90.0MPaISO 2039-1机械性能额定值单位制测试方法拉伸模量 -- 12100MPa ASTM D638 -- 2100MPa ISO 527-2/1 抗张强度屈服 258.6MPa ASTM D638 屈服 55.0MPa ISO 527-2/50 断裂 361.4MPa ASTM D638 断裂 60.0MPa ISO 527-2/50 伸长率屈服 4 6.0%ASTM D638 屈服 6.0%ISO 527-2/50 断裂 5130%ASTM D638 断裂 130%ISO 527-2/50 弯曲模量 50.0 mm 跨距 62070MPa ASTM D790 -- 72200MPa ISO 178 弯曲应力 --85.0MPa ISO 178 屈服, 50.0 mm 跨距888.9MPaASTM D790冲击性能额定值单位制测试方法简支梁缺口冲击强度9ISO 179/1eA -30°C 60kJ/m²ISO 179/1eA 23°C75kJ/m²ISO 179/1eA 简支梁无缺口冲击强度10ISO 179/1eU志-为-塑-胶-提-供136（8665）6661-30°C 无断裂ISO 179/1eU 23°C 无断裂ISO 179/1eU 悬壁梁缺口冲击强度-50°C 590J/m ASTM D256 -30°C 680J/m ASTM D256 23°C 800J/m ASTM D256 23°C, 6.40 mm 640J/m ASTM D256 -30°C 1155kJ/m²ISO 180/1A -30°C 1265kJ/m²ISO 180/4A 23°C 1370kJ/m²ISO 180/1A 23°C 1480kJ/m²ISO 180/4A 无缺口悬臂梁冲击23°C 151100J/m内部方法-30°C 16无断裂ISO 180/1U 23°C 17无断裂ISO 180/1U 装有测量仪表的落镖冲击 (23°C, Total Energy)52.9J ASTM D3763 热性能额定值单位制测试方法载荷下热变形温度0.45 MPa, 未退火, 3.20 mm 134°C ASTM D6480.45 MPa, 未退火, 100 mm 跨距18135°C ISO 75-2/Be1.8 MPa, 未退火, 3.20 mm 121°C ASTM D6481.8 MPa, 未退火, 6.40 mm 124°C ASTM D6481.8 MPa, 未退火, 100 mm 跨距19124°C ISO 75-2/Ae 维卡软化温度-- 142°C ASTM D1525, ISO 306/B120 13 20-- 140°C ISO 306/B50Ball Pressure Test (125°C)Pass IEC 60695-10-2线形热膨胀系数流动 : -40 到 40°C 6.7E-5cm/cm/°C ASTM E831 流动 : 23 到 80°C 7.2E-5cm/cm/°C ISO 11359-2 横向 : -40 到 40°C 6.7E-5cm/cm/°C ASTM E831 横向 : 23 到 80°C 7.7E-5cm/cm/°C ISO 11359-2RTI Elec 125°C UL 746RTI Imp 115°C UL 746RTI 120°C UL 746电气性能额定值单位制测试方法表面电阻率> 1.0E+15ohms IEC 60093体积电阻率> 1.0E+15ohms cm IEC 60093介电强度3.20 mm, in Oil 17kV/mm ASTM D1493.20 mm, 在油中16kV/mm IEC 60243-1介电常数50 Hz 2.95ASTM D15060 Hz 2.95ASTM D1501 MHz 2.90ASTM D15050 Hz 2.60IEC 6025060 Hz 2.60IEC 602501 MHz 2.70IEC 60250耗散因数50 Hz 2.4E-3ASTM D15060 Hz 2.4E-3ASTM D1501 MHz 8.5E-3ASTM D150, IEC 6025050 Hz 1.0E-3IEC 6025060 Hz 1.0E-3IEC 60250相比耐漏电起痕指数(CTI) PLC 3UL 746漏电起痕指数225V IEC 60112高电弧燃烧指数(HAI) PLC 0UL 746热丝引燃 (HWI) PLC 1UL 746可燃性额定值单位制测试方法UL 阻燃等级UL 941.50 mm V-0UL 943.00 mm 5VA UL 94灼热丝易燃指数 (1.00 mm)960°C IEC 60695-2-12 热灯丝点火温度 (1.00 mm)825°C IEC 60695-2-13 极限氧指数35%ISO 4589-2注射额定值单位制干燥温度121°C干燥时间 3.0 到 4.0hr干燥时间,最大48hr建议的最大水分含量0.020%建议注射量40 到 60%料筒后部温度217 到 293°C料筒中部温度282 到 304°C料筒前部温度293 到 316°C射嘴温度288 到 310°C加工(熔体)温度293 到 316°C模具温度71.0 到 93.0°C背压0.345 到 0.689MPa螺杆转速40 到 70rpm排气孔深度0.025 到 0.076mm备注1.50 mm/min2.类型 1, 50 mm/min3.类型 1, 50 mm/min4.类型 1, 50 mm/min5.类型 1, 50 mm/min6. 1.3 mm/min7. 2.0 mm/min8. 1.3 mm/min9.80*10*3 sp=62mm10.80*10*3 sp=62mm11.80*10*312.63.5*12.7*3.213.80*10*314.63.5*12.7*3.215.Double-Gated16.80*10*317.80*10*318.120*10*4 mm19.120*10*4 mm20.标准 B (120°C/h), 载荷2 (50N)。

PBT、PET、PHENOLIC、DAP料物性表

Rockwell 硬度(Rockwell Hardness)
融点（MELTING Poing）热热变形温度（Heat Defection Temp）学热膨胀系数(Coef.OfLinear Thermal Expansion) 性耐燃性(Flammability) 质热传导率
诱电率(Dieletric Const)
理成型收缩率
(a).射出成型(b).移出成型
性 (Shrinkage)
(c).压出成型
质玻璃纤维含量（Glass Fiber Content）
其供应商/产地 Supp Minimum Thickness(mm)
注：此表仅供参考
单位 UNIT M.Pa(kgf/mm2)
PHENOLIC PM-9820 -----
108-137N/mm2
----
3.4-3.9kJ/mm2
226N/mm2 115 --195 --V-0 ----------
1011-1013 1010-1012
9-12kv/mm
125 1.45 0.15-0.25
0.8-1.1
---住友/日本
0.16
1.62-1.66 0.03
%
D955 0.4-2.0
0.2-1.4
%
Ash
15
30
长春/台湾
长春/台湾
0.79
0.74
PET FR-530 11000Mpa
2.0 200Mpa
10300Mpa 91 -------
270-290 246 ---V-0 ----
1E3Hz:3.8
1E3Hz:0.011
10-5cm/cm℃ -------

pc阻燃

pc阻燃物性表资料由金橙塑胶提供如果对防火pc方面还有什么疑问,请与我们详谈!1:德国拜耳系列PC德国拜耳PC 2205 低粘度超高流动德国拜耳PC 2405 低粘度高流动德国拜耳PC 2407 低粘度高流动抗紫外线（UL稳定）德国拜耳PC 2456 低粘度高流动食品级（通过FDA认证）德国拜耳PC 2458 低粘度高流动食品级遮光德国拜耳PC 2605 高流动级德国拜耳PC 2607 高流动抗紫外线（UL稳定）德国拜耳PC 2805 中粘度热稳定耐冲无色透明德国拜耳PC 2807 中粘度抗紫外线级德国拜耳PC 2856 中粘度注塑级食品级德国拜耳PC 2858 中粘度FDA认可食品级。

医疗产品及一般用品德国拜耳PC 2865 中粘度无卤阻燃（UL94-V0 6.0mm）德国拜耳PC 3113 高粘度挤塑吹塑及注塑成型,抗UV德国拜耳PC 3117 高粘度挤塑吹塑及注塑成型,抗UV德国拜耳PC 3105 高粘度,高抗冲击瓷白开关面板专用料德国拜耳PC 3106 高粘度食品级德国拜耳PC 3108 高粘度食品级医疗产品及一般用品德国拜耳PC 3206 高粘度食品级德国拜耳PC 3208 高粘度食品级医疗产品及一般用品德国拜耳PC WB1239 高粘度食品级5加仑水桶料用料德国拜耳PC 6485 阻燃半透明(1.5mm )防火V0德国拜耳PC 6555 中粘度无卤防火透明德国拜耳PC 6557 中粘度无卤防火透明抗UV德国拜耳PC 6717 防火抗紫外线(抗UV)德国拜耳PC 6225 高流动无卤防火德国拜耳PC 8025 20%玻纤增强级高粘度高抗冲德国拜耳PC 8035 30%玻纤增强级高粘度高抗冲德国拜耳PC 8345 35%玻纤增强级高粘度高抗冲德国拜耳PC 9415 玻纤增强10 防火V0德国拜耳PC 9351 玻纤增强防火V0德国拜耳PC APEC 1800 耐高温PC德国拜耳PC APEC 1803 耐高温PC德国拜耳PC APEC 2097 耐高温抗紫外线PC德国拜耳PC APEC 1745 高温PC德国拜耳PC 3103GEF-75 红外线穿透PC德国拜耳PC 2405 450601 红外线穿透PC2:美国基础创新塑料系列PC基础创新塑料PC 121R,121R-111 低粘度高流动无色透明基础创新塑料PC 141R,141R-111 中粘度无色透明基础创新塑料PC 241R,241R-111 低粘度高流动无卤阻燃（UL94-V0 6.0mm）基础创新塑料PC 103R,103R-111 高粘度抗紫外线抗UV基础创新塑料PC 123R,123R-111 低粘度高流动抗紫外线基础创新塑料PC 143R 低粘度高流动抗紫外线基础创新塑料PC 940 中粘度半透明无卤防火基础创新塑料PC 945 中粘度半透明无卤防火基础创新塑料PC 953 高粘度半透明无卤防火基础创新塑料PC 940A,940A-116 防火V0 透明中粘度基础创新塑料PC 945A,945A-116 防火V0 透明中粘度基础创新塑料PC 943A,943A-116 防火V0 透明中粘度抗紫外线基础创新塑料PC 953A 防火V0 透明高粘度抗紫外线基础创新塑料PC 500R,500R-131,500R-739 玻纤增强10% 无卤防火基础创新塑料PC 503R,503R-131,503R-739 玻纤增强10% 无卤阻燃抗紫外线基础创新塑料PC 3412R-131，3412R-739 20%玻纤增强耐高温防火V0基础创新塑料PC 3413R 30%玻纤增强耐高温防火阻燃基础创新塑料PC 3414R 40%玻纤增强耐高温防火V0级基础创新塑料PC HF1110 高流动耐热基础创新塑料PC HF1130 高流动紫外\尺寸稳定耐热基础创新塑料PC HF1140 高流动尺寸稳定耐热食品级基础创新塑料PC PK2870 食品级，包装用料,5加仑水桶料基础创新塑料PC FL900,FL920 耐高温抗蠕变抗冲击基础创新塑料PC FL930 耐高温抗蠕变抗冲击UV稳定基础创新塑料PC EXL1414 超韧耐寒基础创新塑料PC EXL1132T 超韧耐寒基础创新塑料PC EXL9330 超韧耐寒无卤防火V0基础创新塑料PC EXL9112R 超韧耐寒无卤阻燃基础创新塑料PC LS2,LS3 光学级汽车灯专用料基础创新塑料PC DL-4020 20%铁氟龙增强，低磨耗基础创新塑料PC DL-4030 30%铁氟龙/PC合金，低磨耗基础创新塑料PC DMX9455 光扩散磨砂级遮光LED灯泡基础创新塑料PC DMX2415 磨砂级防刮伤3:日本帝人公司系列PC日本帝人PC L-1250Y 高透明,注塑级日本帝人PC L-1225Y 高透明,注塑级日本帝人PC LN-1250G 半透明无卤防火V0级日本帝人PC LN-2250Y 无色透明无卤阻燃日本帝人PC K-1300 高粘度吹瓶级挤塑吹塑及注塑成型日本帝人PC AD-5503 高透明超高流动手机护套专用PC 日本帝人PC ML-1005 光扩散半透明PC LED灯管用日本帝人PC ML-3110ZHP 光扩散半透明PC LED灯泡日本帝人PC ML-3120ZHP 光扩散半透明PC LED灯泡4:日本三菱系列PC日本三菱PC FPR3500 高阻燃防火(0.75mm防火V0)日本三菱PC S-3000VR 抗紫外线耐候性改良高流动日本三菱PC S-2000VR 抗紫外线耐候性改良日本三菱PC S-2000R 食品级FDA认证中粘度日本三菱PC S-3000R 食品级PC FDA日本三菱PC EFD8000 光扩散半透明PC 防火V0 LED灯泡日本三菱PC EFD2110U 光扩散半透明PC 抗紫外线LED灯泡用日本三菱PC EFD2140VUR 光扩散半透明PC LED灯管日本三菱PC EFD2230U 光扩散半透明PC LED灯管5:台湾奇美系列PC台湾奇美PC PC-110 食品级台湾奇美PC PC-110V 阻燃级防火V0台湾奇美PC PC-122V 阻燃高流动级防火V0台湾奇美PC PC-110U 抗紫外线，耐候级台湾奇美PC PC-122U 高流动抗紫外线，耐候级PC6:日本出光系列PC日本出光PC LC1700 导光板专用日本出光PC LC1500 导光板专用日本出光PC URZ2501 背光板专用日本出光PC URZ2502 背光板专用美国液氮PC DC-1004 20%碳纤纤增导电PC 美国液氮PC DC-1006 30%碳纤纤增导电PC。

塑胶原材料物性表

50-90 80~95°4hr, 0.1~0.2%以下 60-100 90°3-5H 750~2400 40~70 70~75°4hr 60~120 80~90°4hr
230-260 易燃 , 黃 ,綠藍色 . 軟化 . 亞克力單體味 180~240 一般
0.018-0.025
170~225(200滯留分解) 800
1.9 1.6 1.2 1.05 1.05 1.05 0.002 0.005 0.6-0.8%
48.1 1.28~2 210-260 1.1948 180~250 1.1~1.68 易燃 , 橙黃 ,有黑煙 .軟化 . PS單體臭味 2.58 1.33~1.6 難燃 , 辛辣氣味綠色底邊 ,黃色火焰 ,尖端綠色 .
about 750 about 750
700~1400 600~1400 500~1000 about 750
60~80 60~90 40-60 90°2-3H 20-40 90°1-2Hr 25~70 25~70 70 以下 (非結晶 ) 130°5hr
0.0045 1.792~2.95 0.002 1.93~2.13 2.88 4.2 1.83~2.4 4.5~4.63
模溫 (C° )
乾燥條件Βιβλιοθήκη ABS (BK) ABS (HB COLOR) 1.05 ABS (HB GF10) 1.2 ABS (HB GF20) 1.22 ABS (HB GF30) ABS (Natural) ABS (PA/757BK) ABS (PA/765AB) ABS (V0 GF10) 1.2 ABS (V0) 1.05 ABS (透明 ) ABS (Acrylonitrile Butadiene Styrene) 丙烯睛 -丁二烯 -苯乙烯 1.05~1.1 AS (GF20) AS=SAN(Styrene-Acrylonitrile 1.26 Copolymer) 丙烯睛 -苯乙烯 1.06 EPS 發泡膠 Expanded PolyStyrene EVA 乙烯 -醋酸乙烯共聚物 . Ethlene-Vinyl Acetate Copolymer橡皮膠 HIPS (BW-4(H45)) HIPS (HB) 高衝擊聚苯乙烯 High Impact PS HIPS (PA-765BK) HIPS (V0) PA +GF30 (V0) PA 66 (HB) PA-6 (聚胺 ). 尼龍 6. Polyamide 1.13 PA-66 1.14 PBT (BK, V0) 1.38 PBT (N)聚對苯二甲酸丁二醇酯 1.38 PBT+ABS (GF30) 1.52 PC(GE10G15) PC(GF40) 1.82 PC(HB) PC(L-1250YN) 1.2 PC(N) 聚碳酸脂 . 防彈膠 Polycarbonate 1.2 PC(透明 ) PC+ABS PC+ABS (FR2000, V0) PC+ABS (KU2-1468,V0) PE 聚乙烯 1.14 PE (Polyethlene) 0.95 PE(High Density PE) 高密 PE(Low Density PE) 低密 PET (GF20) 1.6 PET (GF40) PET (N)聚對苯二甲酸乙二醇酯 1.4 PMMA 1.2 PMMA (80NNC) PMMA (GF20) 1.41 PMMA (亞克力 , 有機玻璃 )聚甲基丙烯酸脂 1.2 POM (9044N) POM (BK,Natural) 1.41 POM (FX-01 BK) 聚甲醛 . 賽鋼 Polyformaldehyde Resin 1.41 POM (HX-01) POM (NW-02 BK) 1.41 PP (BC60) 聚丙烯 Polypropylene PP (COLOR) 0.91 PP (GF20) 1.09 PPO(SE100) 1.1 PPO(SE90) 1.08 PPS (CARBON) 1.34

Valox 553M

Valox553M PBT+PC物性表物理性质公英语评论比重 1.60克/立方厘米 1.60克/立方厘米ASTM D792吸水率0.060％@时间86400秒0.060％@时间24.0小时ASTM D570线性模具收缩，流动0.0010-0.0020厘米/厘米，厚3.20毫米@厚度在0.1260.0010-0.0020/沙伯基础方法0.0030-0.0060厘米/厘米厚度6.40毫米@厚度0.2520.0030-0.0060/沙伯基础方法力学性能公英语评论硬度，洛氏ŗ118118ASTM D785抗拉强度，屈服120兆帕17400磅沙特基础工业公司-日本法断裂伸长率 3.0％ 3.0％沙特基础工业公司-日本法抗弯强度182兆帕26400磅ASTM D790弯曲模量8.09GPA1170KSI ASTM D790悬臂梁缺口冲击强度0.980J/厘米温度23.0°C1.84ft-lb/in温度73.4°FASTM D256电气特性公英语评论表面电阻 1.00E+16欧姆 1.00E+16欧姆ASTM D257介电常数 3.6@频率50.0-60.0赫兹3.6@频率50.0-60.0赫兹ASTM D150耐电弧性60-120秒60-120秒钨，PLC代码6ASTMD495热性能公英语评论线性热膨胀系数，30.0μm/m-°C温度-30.0-30.0°C 16.7μin/in-°F温度-22.0-86.0°FTMA在0.46兆帕的热变形温度（66磅）198°C@厚3.20毫米388°F@厚度在0.126未退火ASTM D648热变形温度在1.8兆200°C392°F未退火ASTM D648帕（264磅）@厚3.20毫米@厚度在0.126易燃，UL94V-0@厚度0.860毫米V-0@厚度0.0339UL945VA 厚度2.30毫米5VA@厚度0.0906UL94。

工程塑料PBT性能表

物性表
环保PBT塑胶粒
化学结构：
特性：
-阻燃性能达到美国UL公司认证的V-0级要求；
-阻燃剂在制品中不析出，增加制品表面光泽；
-制品经热处理后表面不喷霜，适用于有色产品，特别是黑色产品；
-耐热性好，机械强度高，磨擦系数低，耐磨擦；
-有优良的电性能和耐候性；
-耐化学药品性优良，除热水和碱外，PBT工程塑料对大多数化学药品都呈惰性；
1.56
1.60
吸水性23℃50%RH
D570
%
0.09
0.09
0.09
0.10
0.10
收缩率
D955
%
2.0
0.8-1.9
0.7-1.7
0.6-1.5
0.4-1.1
机
械
强
度
拉伸强度
D638
MPa
80
80
90
100
115
伸长率
D638
%
15
4
3
3
2
弯曲强度
D790
MPa
90
130
145
160
185
弯曲模量
使用方法：
-注射成型前必须进行预干燥,干燥温度110-130℃,时间4-5小时(料层厚度不超过3cm)。
注射工艺条件
（仅供参考）：
项目
单位
工艺条件
机筒
温度
后段
℃
230-245
中段
℃
235-250
前段
℃
240-250
喷嘴温度
℃
240-260
树脂温度
℃
240-260
模具温度
℃

PC PBT物性表

宝瑞塑胶原料有限公司
概述材料聚碳酸酯/聚对苯二甲酸丁二醇酯（PBT）混合，非增强
类别：热塑性聚合物聚碳酸酯（PC）聚碳酸酯/聚对苯二甲酸丁二酯（PBT）共混物，非增强聚酯，TP，聚对苯二甲酸丁二醇酯（PBT）
材质说明：此属性数据MatWeb的数据库类别“聚碳酸酯/聚对苯二甲酸丁二酯（PBT）混合，非增强”总结了类似的材料。

报告的每个属性的值范围是适当MatWeb的条目的最小值和最大值。

的注释报告的平均值，用于计算平均值的数据点的数目。

值不一定是典型的任何特定的品位，尤其是不太常见的价值观和那些可以受影响最严重的添加剂或加工方法。

挤出级PBT塑胶原料物性表

宝瑞塑胶原料有限公司
W ww. P 概述材料为聚对苯二甲酸丁二醇酯（PBT），挤出级
类别：聚合物，热塑性聚酯，TP ; 聚对苯二甲酸丁二酯（PBT），聚对苯二甲酸丁二酯（PBT），挤出级
材质说明：此属性数据MatWeb的数据库类别“聚对苯二甲酸丁二酯（PBT），挤出级”总结了类似的材料。

报告的每个属性的值范围是适当MatWeb的条目的最小值和最大值。

的注释报告的平均值，用于计算平均值的数据点的数目。

值不一定是典型的任何特定的品位，尤其是不太常见的价值观和那些可以受影响最严重的添加剂或加工方法。

杜邦高性能聚合物可以是你的合作伙伴，以帮助您进行一个项目从概念到商业化。

我们的产品往往是昂贵的高性能特种聚合物和金属之间架起了一座桥梁。

泰科纳是一个以解决方案为导向的公司，采用先进的聚合物技术生产高性能塑料材料，用于。

PBT 基础创新塑料 420SEO 物性表

PBT基础创新塑料420SEO物性数据表：
产品提供久隆塑胶原料tEl134********
GF30%玻纤增强，阻燃防火VO/5VA，环保型阻燃材料.主要用途：电子电气，食品搅拌机，电机定子和换向器，冷却风扇，连接器，线轴，开关等。

颜色色号有：420SEO-1001、420SEO-BK1066、420SEO-GY4D225、420SEO-7001。

密度（73°F）1580kg/m³ASTM D792
吸水率（24小时）0.06％ASTM D570
断裂拉伸强度117兆帕ASTM D638
弯曲模量7584.22兆帕ASTM D790
弯曲强度185兆帕ASTM D790
洛克硬度R119-ASTM D785
悬臂梁缺口冲击强度（1/8）的0.0694千焦/米ASTM D256
UL94燃烧性V-0-UL94测试厚度0.737毫米
UL94燃烧性5VA@Thickness 2.00mm
热释放速率（平行）25.2E-6/K的ASTM D696
热变形温度@66PSI213℃ASTM D648
热变形温度@264磅191℃ASTM D648
氧指数32％ASTM D2863
电介质强度（短时）24千伏/毫米ASTM D149
耗散因素（1兆赫）0.02-ASTM D150
电介质常数（1兆赫） 3.7-ASTM D150
体积电阻率>1E15欧姆*厘米ASTM D257
耐电弧性90ŞASTM D495。

PBT+GF 物性表

PBT,30%glass fibres,injection moulding,flame retardantISO Shortname:ISO 7792-1-PBT,GFHMR,09-110,GF30;ISO 1043-PBT GF FR(17)PropertyTest ConditionUnitStandardguide valueRheological properties C Melt volume-flow rate 260°C;5kgcm³/(10min)ISO 1133-137C Molding shrinkage,parallel 60x60x2;250°C /WZ 80°C;600bar%ISO 294-40.3C Molding shrinkage,transverse 60x60x2;250°C /WZ 80°C;600bar%ISO 294-40.9Post-shrinkage,parallel 60x60x2;120°C;4h %ISO 294-40.1Post-shrinkage,transverse60x60x2;120°C;4h%ISO 294-40.1Mechanical properties (23°C/50%r.h.)C Tensile modulus 1mm/min MPa ISO 527-1,-211500C Tensile Stress at break 5mm/min MPa ISO 527-1,-2125C Tensile Strain at break 5mm/min %ISO 527-1,-2 2.1C Charpy impact strength 23°C kJ/m²ISO 179-1eU 50C Charpy impact strength -30°C kJ/m²ISO 179-1eU 50C Charpy notched impact strength 23°C kJ/m²ISO 179-1eA <10C Charpy notched impact strength -30°C kJ/m²ISO 179-1eA <10Izod impact strength 23°C kJ/m²ISO 180-1U 45Izod impact strength -30°C kJ/m²ISO 180-1U 45Izod notched impact strength 23°C kJ/m²ISO 180-1A <10Izod notched impact strength -30°C kJ/m²ISO 180-1A <10Flexural modulus 2mm/min MPa ISO 178-A 10500Flexural strength2mm/min MPa ISO 178-A 200Flexural strain at flexural strength 2mm/min%ISO 178-A 2.6Ball indentation hardness N/mm²ISO 2039-1186C Puncture energy 23°C J ISO 6603-2 2.3C Puncture energy -30°C J ISO 6603-2 2.1C Puncture maximum force 23°C N ISO 6603-2669C Puncture maximum force -30°C NISO 6603-2649Thermal properties C Melting temperature10°C/min °C ISO 11357-1,-3225C Temperature of deflection under load 1.80MPa °C ISO 75-1,-2200C Temperature of deflection under load 0.45MPa °C ISO 75-1,-2220Vicat softening temperature50N;120°C/h °C ISO 306205C Coefficient of linear thermal expansion,parallel 23to 55°C 10-4/K ISO 11359-1,-20.2C Coefficient of linear thermal expansion,transverse 23to 55°C 10-4/K ISO 11359-1,-20.9C Burning behavior UL 940.38mm Class UL 94V-0C Burning behavior UL 940.8mm Class UL 94V-0C Oxygen indexMethod A%ISO 4589-232Pocan B 4239000000Page 1of 3PropertyTest Condition Unit Standard guide valueThermal conductivity23°CW/(m·K)ISO 83020.24Resistance to heat (ball pressure test)°C IEC 60695-10-2213Temperature index (Tensile strength)20000h °C IEC 60216-1155Halving interval (Tensile strength)°C IEC 60216-19.3Relative temperature index (Tensile strength)°C UL 746B 140Temperature index (Tensile impact strength)20000h °C IEC 60216-1130Halving interval (Tensile impact strength)°C IEC 60216-18.4Relative temperature index (Tensile impact strength)°C UL 746B 110Temperature index (Electric strength)20000h °C IEC 60216-1145Halving interval (Electric strength)°C IEC 60216-112Relative temperature index (Electric strength)°C UL 746B 125Glow wire test (GWFI)0.8mm °C IEC 60695-2-12960Glow wire test (GWIT)0.8mm °C IEC 60695-2-13725Glow wire test (GWIT) 1.6mm °C IEC 60695-2-13725Glow wire test (GWIT)3.0mm °CIEC 60695-2-13725Electrical properties (23°C/50%r.h.)C Relative permittivity 100Hz -IEC 60250 3.9C Relative permittivity 1MHz -IEC 60250 3.8C Electric strength1mm kV/mm IEC 60243-135C Comparative tracking index CTI Solution AV IEC 60112275Electrolytic corrosion RatingIEC 60426A/B 1Other properties (23°C)C Density kg/m³ISO 11831670Bulk densitykg/m³ISO 60800Processing conditions for test specimens C Injection molding-Melt temperature °C ISO 294250C Injection molding-Mold temperature °CISO 29480Processing recommendations Drying time circulating air dryer h -4-8Drying temperature circulating air dryer °C -120Residual moisture content %Acc.to Karl Fischer 0-0.02Melt temperature (Tmin -Tmax)°C -240-260Mold temperature°C-80-100C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO10350.Pocan B 4239000000Page 2of 3DisclaimerDisclaimer for sales productsThis information and our technical advice -whether verbal,in writing or by way of trials -are given in good faith but without warranty,and this also applies whereproprietary rights of third parties are involved.Our advice does not release you from the obligation to verify the information currently provided -especially that contained in our safety data and technical information sheets -and to test our products as to their suitability for the intended processes and uses.The application,use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and,therefore,entirely your own responsibility.Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery.Test valuesUnless specified to the contrary,the values given have been established on standardized test specimens at room temperature.The figures should be regarded as guide values only and not as binding minimum values.Kindly note that,under certain conditions,the properties can be affected to a considerable extent by the design of the mould/die,the processing conditions and the coloring.Processing noteUnder the recommended processing conditions small quantities of decomposition product may be given off during processing.To preclude any risk to the health and well-being of the machine operatives,tolerance limits for the work environment must be ensured by the provision of efficient exhaust ventilation and fresh air at theworkplace in accordance with the Safety Data Sheet.In order to prevent the partial decomposition of the polymer and the generation of volatile decomposition products,the prescribed processing temperatures should not be substantially exceeded.Since excessively high temperatures are generally the result of operator error or defects in the heating system,special care and controls are essential in these areas.LANXESS DEUTSCHLAND GMBH |D -51369LEVERKUSEN ©LANXESS DeutschlandGmbHPocan B 4239000000Page 3of 3。

PBT物性

改性PBT、PET工程塑料系列
项目密度拉伸强度断裂伸长率弯曲强度弯曲模量 IZOD缺口冲击强度热变形温度（1.82MPa) 模塑收缩率阻燃等级材质说明测试方法 ASTM D792 D638 D638 D790 D790 D256 D648 D955 GB 1033 1040 1040 9341 9341 1834 1634 15585 UL94 单位 g/cm % MPa MPa J/M ℃ %
用途
3
性ቤተ መጻሕፍቲ ባይዱ PBT-VG10 1.48 85 3 130 4200 95 195 0.5-1.2 V-0 PBT-VG20 1.55 110 3 150 5700 105 205 0.4-0.8 V-0 PBT-VG30 1.62 125 2 160 7300 122 215 0.3-0.6 V-0 PET-VG10 PET-VG20 PET-VG30 PBT-V0 1.5 95 3 155 5200 106 215 0.6-1.2 V-0 1.58 123 3 170 6700 112 235 0.5-1.0 V-0 1.67 140 2 183 8300 128 250 0.3-0.6 V-0 1.47 55 30 95 2700 63 70 1.2-1.7 V-0 PET-V0 1.49 58 15 92 2800 60 75 1.2-1.7 V-0 阻燃PET 15%玻纤 30%玻纤 15%玻纤增 30%玻纤增增强PBT 增强PBT 强PET 强PET PBT-G15 1.42 67 3 105 3350 90 197 0.6-1.5 PBT-G30 1.55 98 2 140 6100 117 217 0.3-0.7 PET-G15 1.44 101 3 140 5800 105 225 0.6-1.5 PET-G30 1.56 132 2 167 7700 123 255 0.3-1.5

PBT+GF30%物性表

PBT,30%glass fibres,injection moulding,flame retardantISO Shortname:ISO 7792-1-PBT,GFHMR,09-110,GF30;ISO 1043-PBT GF FR(17)PropertyTest ConditionUnitStandardguide valueRheological properties C Melt volume-flow rate 260°C;5kgcm³/(10min)ISO 1133-137C Molding shrinkage,parallel 60x60x2;250°C /WZ 80°C;600bar%ISO 294-40.3C Molding shrinkage,transverse 60x60x2;250°C /WZ 80°C;600bar%ISO 294-40.9Post-shrinkage,parallel 60x60x2;120°C;4h %ISO 294-40.1Post-shrinkage,transverse60x60x2;120°C;4h%ISO 294-40.1Mechanical properties (23°C/50%r.h.)C Tensile modulus 1mm/min MPa ISO 527-1,-211500C Tensile Stress at break 5mm/min MPa ISO 527-1,-2125C Tensile Strain at break 5mm/min %ISO 527-1,-2 2.1C Charpy impact strength 23°C kJ/m²ISO 179-1eU 50C Charpy impact strength -30°C kJ/m²ISO 179-1eU 50C Charpy notched impact strength 23°C kJ/m²ISO 179-1eA <10C Charpy notched impact strength -30°C kJ/m²ISO 179-1eA <10Izod impact strength 23°C kJ/m²ISO 180-1U 45Izod impact strength -30°C kJ/m²ISO 180-1U 45Izod notched impact strength 23°C kJ/m²ISO 180-1A <10Izod notched impact strength -30°C kJ/m²ISO 180-1A <10Flexural modulus 2mm/min MPa ISO 178-A 10500Flexural strength2mm/min MPa ISO 178-A 200Flexural strain at flexural strength 2mm/min%ISO 178-A 2.6Ball indentation hardness N/mm²ISO 2039-1186C Puncture energy 23°C J ISO 6603-2 2.3C Puncture energy -30°C J ISO 6603-2 2.1C Puncture maximum force 23°C N ISO 6603-2669C Puncture maximum force -30°C NISO 6603-2649Thermal properties C Melting temperature10°C/min °C ISO 11357-1,-3225C Temperature of deflection under load 1.80MPa °C ISO 75-1,-2200C Temperature of deflection under load 0.45MPa °C ISO 75-1,-2220Vicat softening temperature50N;120°C/h °C ISO 306205C Coefficient of linear thermal expansion,parallel 23to 55°C 10-4/K ISO 11359-1,-20.2C Coefficient of linear thermal expansion,transverse 23to 55°C 10-4/K ISO 11359-1,-20.9C Burning behavior UL 940.38mm Class UL 94V-0C Burning behavior UL 940.8mm Class UL 94V-0C Oxygen indexMethod A%ISO 4589-232Pocan B 4239000000Page 1of 3PropertyTest Condition Unit Standard guide valueThermal conductivity23°CW/(m·K)ISO 83020.24Resistance to heat (ball pressure test)°C IEC 60695-10-2213Temperature index (Tensile strength)20000h °C IEC 60216-1155Halving interval (Tensile strength)°C IEC 60216-19.3Relative temperature index (Tensile strength)°C UL 746B 140Temperature index (Tensile impact strength)20000h °C IEC 60216-1130Halving interval (Tensile impact strength)°C IEC 60216-18.4Relative temperature index (Tensile impact strength)°C UL 746B 110Temperature index (Electric strength)20000h °C IEC 60216-1145Halving interval (Electric strength)°C IEC 60216-112Relative temperature index (Electric strength)°C UL 746B 125Glow wire test (GWFI)0.8mm °C IEC 60695-2-12960Glow wire test (GWIT)0.8mm °C IEC 60695-2-13725Glow wire test (GWIT) 1.6mm °C IEC 60695-2-13725Glow wire test (GWIT)3.0mm °CIEC 60695-2-13725Electrical properties (23°C/50%r.h.)C Relative permittivity 100Hz -IEC 60250 3.9C Relative permittivity 1MHz -IEC 60250 3.8C Electric strength1mm kV/mm IEC 60243-135C Comparative tracking index CTI Solution AV IEC 60112275Electrolytic corrosion RatingIEC 60426A/B 1Other properties (23°C)C Density kg/m³ISO 11831670Bulk densitykg/m³ISO 60800Processing conditions for test specimens C Injection molding-Melt temperature °C ISO 294250C Injection molding-Mold temperature °CISO 29480Processing recommendations Drying time circulating air dryer h -4-8Drying temperature circulating air dryer °C -120Residual moisture content %Acc.to Karl Fischer 0-0.02Melt temperature (Tmin -Tmax)°C -240-260Mold temperature°C-80-100C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO10350.Pocan B 4239000000Page 2of 3DisclaimerDisclaimer for sales productsThis information and our technical advice -whether verbal,in writing or by way of trials -are given in good faith but without warranty,and this also applies whereproprietary rights of third parties are involved.Our advice does not release you from the obligation to verify the information currently provided -especially that contained in our safety data and technical information sheets -and to test our products as to their suitability for the intended processes and uses.The application,use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and,therefore,entirely your own responsibility.Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery.Test valuesUnless specified to the contrary,the values given have been established on standardized test specimens at room temperature.The figures should be regarded as guide values only and not as binding minimum values.Kindly note that,under certain conditions,the properties can be affected to a considerable extent by the design of the mould/die,the processing conditions and the coloring.Processing noteUnder the recommended processing conditions small quantities of decomposition product may be given off during processing.To preclude any risk to the health and well-being of the machine operatives,tolerance limits for the work environment must be ensured by the provision of efficient exhaust ventilation and fresh air at theworkplace in accordance with the Safety Data Sheet.In order to prevent the partial decomposition of the polymer and the generation of volatile decomposition products,the prescribed processing temperatures should not be substantially exceeded.Since excessively high temperatures are generally the result of operator error or defects in the heating system,special care and controls are essential in these areas.LANXESS DEUTSCHLAND GMBH |D -51369LEVERKUSEN ©LANXESS DeutschlandGmbHPocan B 4239000000Page 3of 3。

PC基础创新EXL9330物性表

LEXAN™ EXL9330 resin聚碳酸酯SABIC Innovative Plastics产品说明Opaque PC-Siloxane copolymer with excellent processability. Non-chlorinated, non-brominated flame retardant product in most colors. UV-stabilized. UL rated f1/V-0/5VA.添加剂紫外线稳定剂阻燃性特性Chlorine Free 共聚物可加工性,良好无溴阻燃性RoHS 合规性RoHS 合规外观不透明加工方法注射成型物理性能额定值单位制测试方法比重 -- 1.18g/cm³ASTM D792 --1.19g/cm³ISO 1183 熔流率(熔体流动速率) (300°C/1.2 kg)10g/10 min ASTM D1238 溶化体积流率(MVR) (300°C/1.2 kg)9.00cm³/10min ISO 1133 收缩率内部方法流动 : 3.20 mm 0.40 到 0.80%内部方法横向流动 : 3.20 mm 0.40 到 0.80%内部方法吸水率 ISO 62 饱和, 23°C0.35%ISO 62 平衡, 23°C, 50% RH 0.15%ISO 62 室外适用性f1UL 746C硬度额定值单位制测试方法球压硬度 (H 358/30)90.0MPaISO 2039-1机械性能额定值单位制测试方法拉伸模量 -- 12100MPa ASTM D638 -- 2100MPa ISO 527-2/1 抗张强度屈服 258.6MPa ASTM D638 屈服 55.0MPa ISO 527-2/50 断裂 361.4MPa ASTM D638 断裂 60.0MPa ISO 527-2/50 伸长率屈服 4 6.0%ASTM D638 屈服 6.0%ISO 527-2/50 断裂 5130%ASTM D638 断裂 130%ISO 527-2/50 弯曲模量 50.0 mm 跨距 62070MPa ASTM D790 -- 72200MPa ISO 178 弯曲应力 --85.0MPa ISO 178 屈服, 50.0 mm 跨距888.9MPaASTM D790冲击性能额定值单位制测试方法简支梁缺口冲击强度9ISO 179/1eA -30°C 60kJ/m²ISO 179/1eA 23°C75kJ/m²ISO 179/1eA 简支梁无缺口冲击强度10ISO 179/1eU志-为-塑-胶-提-供136（8665）6661-30°C 无断裂ISO 179/1eU 23°C 无断裂ISO 179/1eU 悬壁梁缺口冲击强度-50°C 590J/m ASTM D256 -30°C 680J/m ASTM D256 23°C 800J/m ASTM D256 23°C, 6.40 mm 640J/m ASTM D256 -30°C 1155kJ/m²ISO 180/1A -30°C 1265kJ/m²ISO 180/4A 23°C 1370kJ/m²ISO 180/1A 23°C 1480kJ/m²ISO 180/4A 无缺口悬臂梁冲击23°C 151100J/m内部方法-30°C 16无断裂ISO 180/1U 23°C 17无断裂ISO 180/1U 装有测量仪表的落镖冲击 (23°C, Total Energy)52.9J ASTM D3763 热性能额定值单位制测试方法载荷下热变形温度0.45 MPa, 未退火, 3.20 mm 134°C ASTM D6480.45 MPa, 未退火, 100 mm 跨距18135°C ISO 75-2/Be1.8 MPa, 未退火, 3.20 mm 121°C ASTM D6481.8 MPa, 未退火, 6.40 mm 124°C ASTM D6481.8 MPa, 未退火, 100 mm 跨距19124°C ISO 75-2/Ae 维卡软化温度-- 142°C ASTM D1525, ISO 306/B120 13 20-- 140°C ISO 306/B50Ball Pressure Test (125°C)Pass IEC 60695-10-2线形热膨胀系数流动 : -40 到 40°C 6.7E-5cm/cm/°C ASTM E831 流动 : 23 到 80°C 7.2E-5cm/cm/°C ISO 11359-2 横向 : -40 到 40°C 6.7E-5cm/cm/°C ASTM E831 横向 : 23 到 80°C 7.7E-5cm/cm/°C ISO 11359-2RTI Elec 125°C UL 746RTI Imp 115°C UL 746RTI 120°C UL 746电气性能额定值单位制测试方法表面电阻率> 1.0E+15ohms IEC 60093体积电阻率> 1.0E+15ohms cm IEC 60093介电强度3.20 mm, in Oil 17kV/mm ASTM D1493.20 mm, 在油中16kV/mm IEC 60243-1介电常数50 Hz 2.95ASTM D15060 Hz 2.95ASTM D1501 MHz 2.90ASTM D15050 Hz 2.60IEC 6025060 Hz 2.60IEC 602501 MHz 2.70IEC 60250耗散因数50 Hz 2.4E-3ASTM D15060 Hz 2.4E-3ASTM D1501 MHz 8.5E-3ASTM D150, IEC 6025050 Hz 1.0E-3IEC 6025060 Hz 1.0E-3IEC 60250相比耐漏电起痕指数(CTI) PLC 3UL 746漏电起痕指数225V IEC 60112高电弧燃烧指数(HAI) PLC 0UL 746热丝引燃 (HWI) PLC 1UL 746可燃性额定值单位制测试方法UL 阻燃等级UL 941.50 mm V-0UL 943.00 mm 5VA UL 94灼热丝易燃指数 (1.00 mm)960°C IEC 60695-2-12 热灯丝点火温度 (1.00 mm)825°C IEC 60695-2-13 极限氧指数35%ISO 4589-2注射额定值单位制干燥温度121°C干燥时间 3.0 到 4.0hr干燥时间,最大48hr建议的最大水分含量0.020%建议注射量40 到 60%料筒后部温度217 到 293°C料筒中部温度282 到 304°C料筒前部温度293 到 316°C射嘴温度288 到 310°C加工(熔体)温度293 到 316°C模具温度71.0 到 93.0°C背压0.345 到 0.689MPa螺杆转速40 到 70rpm排气孔深度0.025 到 0.076mm备注1.50 mm/min2.类型 1, 50 mm/min3.类型 1, 50 mm/min4.类型 1, 50 mm/min5.类型 1, 50 mm/min6. 1.3 mm/min7. 2.0 mm/min8. 1.3 mm/min9.80*10*3 sp=62mm10.80*10*3 sp=62mm11.80*10*312.63.5*12.7*3.213.80*10*314.63.5*12.7*3.215.Double-Gated16.80*10*317.80*10*318.120*10*4 mm19.120*10*4 mm20.标准 B (120°C/h), 载荷2 (50N)。

PBT+PC 基础创新塑料 553 物性表

PBT/PC基础创新塑料VALOX553物性表：产品提供久隆塑胶原料tEl134********GF30％玻璃纤维增强，阻燃V0,PBT+PC共混物,具有良好的翘曲的特点。

应用：泵壳、轴承座、电器元件，聚光灯，电动马达，泵配件。

30%GR PBT+PC,UL94V-0.Reduced warpage characteristics.Applications; appliance handles,spotlights,electric motors,pump housings,etc.密度（73°F）1590公斤/立方米ASTM D792吸水率（24小时）0.07％ASTM D570熔体流动7.0g/10分钟负荷2.16公斤，温度250℃断裂伸长率 2.5％5毫米/分钟;ASTM D638断裂拉伸强度110兆帕ASTM D638弯曲模量6887.85兆帕ASTM D790弯曲强度179兆帕ASTM D790洛克硬度R118-ASTM D785悬臂梁缺口冲击强度（1/8）的0.0854千焦/米ASTM D256UL94燃烧性V-0-UL94测试厚度0.864毫米氧指数34％ISO45890.46兆帕的热变形温度（66磅）205°C ISO75/Be热变形温度在1.8兆帕（264磅）135°C ISO75/Ae热释放速率（平行）21.6E-6/K ASTM D696电介质强度（短时）25.6千伏/毫米ASTM D149耗散因素（1兆赫）0.02-ASTM D150电介质常数（1兆赫） 3.7-ASTM D150体积电阻率>1E15欧姆*厘米ASTM D257耐电弧性90ŞASTM D495。