Quartus II常见错误

1.Found clock-sensitive change during active clock edge at time <time> on register "<name>"原因：vector source file中时钟敏感信号（如：数据，允许端，清零，同步加载等）在时钟的边缘同时变化。

而时钟敏感信号是不能在时钟边沿变化的。

其后果为导致结果不正确。

措施：编辑vector source file2.Verilog HDL assignment warning at <location>: truncated with size <number> to match size of target (<number>原因:在HDL设计中对目标的位数进行了设定,如:reg[4:0] a;而默认为32位,将位数裁定到合适的大小措施:如果结果正确,无须加以修正,如果不想看到这个警告,可以改变设定的位数3.All reachable assignments to data_out(10) assign '0', register removed by optimization原因:经过综合器优化后，输出端口已经不起作用了4.Following 9 pins have nothing, GND, or VCC driving datain port -- changes to this connectivity may change fitting results原因:第9脚，空或接地或接上了电源措施:有时候定义了输出端口，但输出端直接赋…0‟，便会被接地，赋…1‟接电源。

如果你的设计中这些端口就是这样用的，那便可以不理会这些warning5.Found pins ing as undefined clocks and/or memory enables原因:是你作为时钟的PIN没有约束信息。

可以对相应的PIN做一下设定就行了。

主要是指你的某些管脚在电路当中起到了时钟管脚的作用，比如flip-flop的clk管脚，而此管脚没有时钟约束，因此QuartusII把“clk”作为未定义的时钟。

措施:如果clk不是时钟，可以加“not clock”的约束；如果是，可以在clock setting当中加入；在某些对时钟要求不很高的情况下，可以忽略此警告或在这里修改:Assignments>Timing analysis settings...>Individual clocks...>...6.Timing characteristics of device EPM570T144C5 are preliminary原因:因为MAXII 是比較新的元件在QuartusII 中的時序并不是正式版的,要等Service Pack措施:只影响Quartus 的Waveform7.Warning: Clock latency analysis for PLL offsets is supported for the current device family, but is not enabled措施:将setting中的timing Requirements&Option-->More Timing Setting-->setting-->Enable Clock Latency中的on改成OFF8.Found clock high time violation at 14.8 ns on register "|counter|lpm_counter:count1_rtl_0|dffs[11]"原因:违反了steup/hold时间，应该是后仿真，看看波形设置是否和时钟沿符合steup/hold 时间措施:在中间加个寄存器可能可以解决问题9.warning: circuit may not operate.detected 46 non-operational paths clocked by clock clk44 with clock skew larger than data delay原因:时钟抖动大于数据延时,当时钟很快，而if等类的层次过多就会出现这种问题,但这个问题多是在器件的最高频率中才会出现措施：setting-->timing Requirements&Options-->Default required fmax 改小一些，如改到50MHZ10.Design contains <number> input pin(s) that do not drive logic原因:输入引脚没有驱动逻辑(驱动其他引脚）,所有的输入引脚需要有输入逻辑措施:如果这种情况是故意的,无须理会,如果非故意,输入逻辑驱动.11.Warning：Found clock high time violation at 8.9ns on node 'TEST3.CLK'原因：FF中输入的PLS的保持时间过短措施：在FF中设置较高的时钟频率12.Warning: Found 10 node(s) in clock paths which may be acting as ripple and/or gated clocks -- node(s) analyzed as buffer(s) resulting in clock skew原因:如果你用的CPLD 只有一组全局时钟时，用全局时钟分频产生的另一个时钟在布线中当作信号处理，不能保证低的时钟歪斜(SKEW)。

会造成在这个时钟上工作的时序电路不可靠，甚至每次布线产生的问题都不一样。

措施:如果用有两组以上全局时钟的FPGA 芯片，可以把第二个全局时钟作为另一个时钟用，可以解决这个问题。

13.Critical Warning: Timing requirements were not met. See Report window for details.原因：时序要求未满足，措施：双击Compilation Report-->Time Analyzer-->红色部分（如clock setup:'clk'等）-->左键单击list path,查看fmax的SLACK REPORT再根据提示解决,有可能是程序的算法问题14.Can't achieve minimum setup and hold requirement <text> along <number> path(s). See Report window for details.原因：时序分析发现一定数量的路径违背了最小的建立和保持时间，与时钟歪斜有关,一般是由于多时钟引起的措施：利用Compilation Report-->Time Analyzer-->红色部分（如clock hold:'clk'等），在slack中观察是hold time为负值还是setup time 为负值，然后在：Assignment-->Assignment Editor-->To中增加时钟名(from node finder)，Assignment Name中增加多时钟有关的Multicycle 和Multicycle Hold选项，如hold time为负，可使Multicycle hold的值>multicycle,如设为2和1。

15: Can't analyze file -- file E://quartusii/*/*.v is missing原因：试图编译一个不存在的文件，该文件可能被改名或者删除了措施：不管他，没什么影响16.Warning: Can't find signal in vector source file for input pin |whole|clk10m原因：因为你的波形仿真文件（vector source file ）中并没有把所有的输入信号(input pin)加进去，对于每一个输入都需要有激励源的17.Error: Can't name logic scfifo0 of instance "inst" -- has same name as current design file原因：模块的名字和project的名字重名了措施：把两个名字之一改一下，一般改模块的名字18.Warning: Using design file lpm_fifo0.v, which is not specified as a design file for the current project, but contains definitions for 1 design units and 1 entities in project Info: Found entity 1: lpm_fifo0原因：模块不是在本项目生成的，而是直接copy了别的项目的原理图和源程序而生成的，而不是用QUARTUS将文件添加进本项目措施：无须理会，不影响使用19.Timing characteristics of device <name> are preliminary原因：目前版本的QuartusII只对该器件提供初步的时序特征分析措施：如果坚持用目前的器件，无须理会该警告。

关于进一步的时序特征分析会在后续版本的Quartus得到完善。

20.Timing Analysis does not support the analysis of latches as synchronous elements for thecurrently selected device family原因：用analyze_latches_as_synchronous_elements setting可以让Quaruts II来分析同步锁存，但目前的器件不支持这个特性措施：无须理会。

时序分析可能将锁存器分析成回路。

但并不一定分析正确。

其后果可能会导致显示提醒用户：改变设计来消除锁存器21.Warning:Found xx output pins without output pin load capacitance assignment（网友：gucheng82提供）原因：没有给输出管教指定负载电容措施：该功能用于估算TCO和功耗，可以不理会，也可以在Assignment Editor中为相应的输出管脚指定负载电容，以消除警告22.Warning: Found 6 node(s) in clock paths which may be acting as ripple and/or gated clocks -- node(s) analyzed as buffer(s) resulting in clock skew原因：使用了行波时钟或门控时钟，把触发器的输出当时钟用就会报行波时钟，将组合逻辑的输出当时钟用就会报门控时钟措施：不要把触发器的输出当时钟，不要将组合逻辑的输出当时钟，如果本身如此设计，则无须理会该警告23.Warning (10268): V erilog HDL information at lcd7106.v(63): Always Construct contains both blocking and non-blocking assignments原因：一个always模块中同时有阻塞和非阻塞的赋值１Warning: VHDL Process Statement warning at random.vhd(18): signal reset is in statement, but is not in sensitivity list----没把singal放到process（）中2 Warning: Found pins ing as undefined clocks and/or memory enablesInfo: Assuming node CLK is an undefined clock-=-----可能是说设计中产生的触发器没有使能端3 Error: VHDL Interface Declaration error in clk_gen.vhd(29): interface object "clk_scan" of mode out cannot be read. Change object mode to buffer or inout.------信号类型设置不对，out当作buffer来定义4 Error: Node instance "clk_gen1" instantiates undefined entity "clk_gen"-------引用的例化元件未定义实体－－entity "clk_gen"5 Warning: Found 2 node(s) in clock paths which may be acting as ripple and/or gated clocks -- node(s) analyzed as buffer(s) resulting in clock skewInfo: Detected ripple clock "clk_gen:clk_gen1|clk_incr" as bufferInfo: Detected ripple clock "clk_gen:clk_gen1|clk_scan" as buffer6 Warning: VHDL Process Statement warning at ledmux.vhd(15): signal or variable "dataout" may not be assigned a new in every possible path through the Process Statement. Signal or variable "dataout" holds its previous in every path with no new assignment, which may create a combinational loop in the current design.7 Warning: VHDL Process Statement warning at divider_10.vhd(17): signal "cnt" is read inside the Process Statement but isn't in the Process Statement's sensivitity list-----缺少敏感信号8 Warning: No clock transition on "counter_bcd7:counter_counter_clk|q_sig[3]" register9 Warning: Reduced register "counter_bcd7:counter_counter_clk|q_sig[3]" with stuck clock port to stuck GND10 Warning: Circuit may not operate. Detected 1 non-operational path(s) clocked by clock "class[1]" with clock skew larger than data delay. See Compilation Report for details.11 Warning: Circuit may not operate. Detected 1 non-operational path(s) clocked by clock "sign" with clock skew larger than data delay. See Compilation Report for details.12 Error: VHDL error at counter_clk.vhd(90): actual port "class" of mode "in" cannot be associated with formal port "class" of mode "out"------两者不能连接起来13 Warning: Ignored node in vector source file. Can't find corresponding node name "class_sig[2]" in design.------没有编写testbench文件，或者没有编辑输入变量的值testbench里是元件申明和映射14 Error: VHDL Binding Indication error at freqdetect_top.vhd(19): port "class" in design entity does not have std_logic_vector type that is specified for the same generic in the associated component---在相关的元件里没有当前文件所定义的类型15 Error: VHDL error at tongbu.vhd(16): can't infer register for signal "gate" because signal does not hold its outside clock edge16 Warning: Found clock high time violation at 1000.0 ns on register "|fcounter|lpm_counter:temp_rtl_0|dffs[4]"17 Warning: Compiler packed, optimized or synthesized away node "temp[19]". Ignored vector source file node.---"temp[19]"被优化掉了18 Warning: Reduced register "gate~reg0" with stuck data_in port to stuck GND19 Warning: Design contains 2 input pin(s) that do not drive logicWarning: No output dependent on input pin "clk"Warning: No output dependent on input pin "sign"------输出信号与输入信号无关，20 Warning: Found clock high time violation at 16625.0 ns on register "|impulcomp|gate1"21 Error: VHDL error at impulcomp.vhd(19): can't implement clock enable condition specified using binary operator "or"22 Error: VHDL Association List error at period_counter.vhd(38): actual parameter assigned to formal parameter "alarm", but formal parameter is not declared-------连接表错误，形参"alarm"赋值给实参，形参没定义，可能是形参与实参的位置颠倒了，规定形参在实参之前。