串口转SD卡数据记录仪说明书、文件系统(全能版)

合集下载

实时SD卡数据记录仪说明书

Real timeSD CARD DATA LOGGER Model : DL-9602SD ISO-9001, CE, IEC1010LUTRON ELECTRONICreal timeSD CARD DATA LOGGERModel : DL-9602SDFEATURES*Real time SD memory card Datalogger, it can Input Direct RS232 signal input.cooperate with most LUTRON instruments if it build Signal Isolate RS232 signal input.in the computer interface. Advanced *SD memory card Format*Built-in Clock and Calendar, real time data setting *Set input channel No.recorder , sampling time set from 1 second to 8Set clock time ( Year/Month/Date,hours 59 minutes 59 seconds.Hour/Minute/ Second )*Manual datalogger is available ( set the sampling *Set sampling time ( Hour/Minute/time to 0 ), during execute the manual datalogger Second )function, it can set the different place ( location ) No. *Auto power OFF management( place 1 to place 99 ). *Set LCD backlight ON/OFF*Innovation and easy operation, computer is not *Set beeper sound ON/OFFneed to setup extra software, after execute Power off Auto shut off saves battery life or datalogger, just take away the SD card from the manual off by push button.meter and plug in the SD card into the computer,Sampling Time Auto 2 seconds to 8 hours 59 min.it can down load the measured value with the Setting range59 seconds.time information ( year/month/date/@Sampling time can set to 1 second, hour/minute/second ) to the Excel directly, then but memory data may lossuser can make the further data or graphic Manual Push the data logger button analysis by themselves.once will save data one time.*SD card capacity : 1 GB to 16 GB.@Set the sampling time to*Can set the numerical decimal point character to " . " 0 second.or " , " with default, then Datalogger data that saved Data Output RS 232/USB PC computer interface.into the SD card can be used in different country.*The output data structure are same as*Can set max. 9 channels data input with default.the input data.*DC 1.5V battery ( UM-3 , AA ) x 6 or DC 9V*Connect the optional RS232 cableadapter in.UPCB-02 will get the RS232 plug.*LCD with green light backlight, easy reading.*Connect the optional USB cable*RS232 signal output, can connect the external USB-01 will get the USB plug.℃computer.Operating 0 to 50 .TemperatureSPECIFICATIONS Operating Less than 85% R.H.Application*Real time SD memory card HumidityDatalogger can cooperate with all Power Supply* A Alkaline or heavy duty DC 1.5 V batteryLUTRON instruments if it build in( UM3, AA ) x 6 PCs, or equivalent.the computer interface. * A DC 9V adapter input. ( AC/DC power*Innovation and easy operation, adapter is optional ).computer no need to setup extra Power Current Normal operation ( w/o SD card savesoftware, after execute datalogger, just data and LCD Backlight is OFF) :plug in the SD card into the computer,Approx. DC 7 mA.it can down load the all the measured When SD card save the data and LCDvalue and unit along with the time Backlight is OFF) :information ( year/month/date/Approx. DC 28 mA.hour/minute/second ) to the Excel* A If LCD backlight on, the powerdirectly, user can make the further data consumption will increase approx.or graphic analysis by themselves.17 mA.Circuit Custom one-chip of microprocessor LSI Weight468 g/1.03 LB.circuit.Dimension178 x 68 x 44 mmDisplay LCD size : 52 mm x 38 mm(7.0 x 2.7x 1.7 inch)LCD with Backlight ( ON/OFF ).Accessories *Instruction manual...........................1 PCIncluded *Double earphone cable, UPCB-03.......................................................1 PC PATENT CHINA : ZL 2008 2 0189918.5 ZL 2008 2 0189917.0TAIWAN : M 358970 M 359043Germany : Nr. 20 2008 016 337.4JAPAN : 3151214 U.S.A. : Pending* Appearance and specifications listed in this brochure are subject to change without notice. 0909-DL9602SD。

Micro SD 卡读卡器说明书

了解您的手机飞利浦将不断力争改善产品性能并确保该用户指南的准确性。

因为手机软件版本的更新，本手册中的某些内容可能与您的手机有所差异。

飞利浦保留修改本用户指南的权利，如有更改，恕不另行通知。

请以手机实际操作为准。

主屏幕耳机右软键挂断、取消和开/关机键左软键导航键/确认键接听键充电/USB 接口待机屏待机屏由以下部分组成：按键了解主要按键如何操作。

功能(拨号拨打或接听电话。

,确认及导航键选择或确认菜单功能。

)挂机/退出/开关机结束通话; 返回待机屏;长按开启/关闭手机。

L 左软键选取屏幕上的对应选项。

R右软键选取屏幕上的对应选项。

*键盘锁在待机屏，长按*锁定键盘;或先按L ，再按* 锁定键盘或为键盘解锁。

图标行快捷菜单图标与符号了解显示屏上显示的图标。

静音来电时手机会静音。

振动来电时手机会振动。

电池指示条显示电量状态。

短信您收到一条新短信。

未接电话您有一个未接电话。

耳机耳机已接连到手机。

GSM网络手机已连接到GSM 网络。

指示条越多，接收质量越好。

GPRS连接手机已连接到GPRS网络。

第一次使用安装与充电首次使用手机时，如何安装SIM卡及给手机充电。

插入SIM卡234为电池充电新电池已部分充电，手机屏幕上的电池图标表示电量状态。

插入Micro SD卡(存储卡)提示：•充电时，您仍可以使用手机。

•电池完全充电后，将充电器继续连接在手机上不会损坏电池。

如需关闭充电器，应将其从电源上拔下。

因此，请选择易于您插拔的插座。

•如果您几天内都不会使用手机，建议您取出电池。

•如果已完全充电的电池搁置不用,电池本身在一段时间后,会因自放电而处于无电压或低电压状态。

•新电池或长时间未使用的电池,需要较长时间充电。

您可在手机中插入Micro SD卡以扩展手机存储容量。

将Micro SD卡与卡槽对齐并放入卡槽。

使用您的手机如何拨打电话拨出电话1输入电话号码。

2按(拨打该号码。

3按)挂机。

提示：•如需拨打国际长途电话，长按0输入国际前缀“+”。

致远电子 DM100数据采集记录仪产品说明书

广州致远电子股份有限公司DM100数据采集记录仪修订历史目录1.前言 (1)1.1关于本说明书 (1)1.2安全须知 (1)2.基本操作 (2)2.1操作流程 (2)2.2安装模块 (2)2.3连接单元 (3)2.4输入输出接线 (3)2.4.1模拟输入模块DM90XA接线 (3)2.4.2数字模块接线 (4)2.5打开电源 (4)2.6配置系统 (5)2.6.1设置IP地址 (5)2.6.2设置时间日期 (6)2.6.3板卡自动配置 (6)2.7设置参数 (7)2.7.1设置测量输入 (7)2.7.2设置报警条件 (8)2.7.3设置测量周期 (9)2.7.4设置记录条件 (9)2.7.5设置显示组 (11)2.8测量/记录 (12)2.8.1查看测量结果 (12)2.8.2开始/停止记录 (12)2.8.3浏览历史记录 (12)3. Modbus通信操作 (15)3.1Modbus服务器 (15)3.1.1接线 (15)3.1.2设置Modbus服务器功能 (15)3.1.3客户端设备读写DM100/DP100的数据 (16)3.2Modbus客户端 (18)3.2.1接线 (18)3.2.2设置Modbus客户端 (19)3.2.3查看Modbus通信结果 (22)1.前言1.1 关于本说明书本说明书说明数据采集记录仪DM100/DP100的安装、接线方法，和基础操作。

本说明书对应以下型号的产品。

1.2 安全须知●在使用测试仪及其配件之前，请先完整阅读使用说明书；●请勿在高温、有爆炸性气体、蒸汽或者有大量灰尘的地方使用记录仪；●运输和保存本产品时，请确保记录仪处于关机状态；●如需测试本产品，请使用合格的测试设备或检测装置；●记录仪如果出现问题需要维修，请勿自行拆卸，请及时与本公司联系。

2.基本操作本产品的使用说明书可以从以下地址下载阅览。

URL：最新版固件可以从以下地址下载安装。

URL：2.1 操作流程2.2 安装模块一台主机DM100（或扩展模块）最多可以连接10个采集模块。

海康威士-SD1手持数据记录仪说明书

B-1Handheld Data Logging Meter with SD CardFor Measuring Conductivity, TDS, Salt Concentration, pH, ORP and DOHHWT-SD1U D issolved Oxygen Measurements canbe Compensated for Salt, Altitude and Temperature U M easures Oxygen Content of a Volume of Air U Optional ATC for pH CompensationU Records Maximum and Minimum Readings U P erforms Real-Time Automatic Data Logging U Sampling Time Settable from 1 Sec to 9 Hrs U Large Easy-to-Read Green Backlit LCD U Auto Power-Off FunctionThe HHWT-SD1 is a general purpose handheld instrument capable of measuring the pH, Oxidation-Reduction Potential (ORP) or conductivity of a solution, as well as its TDS (Total Dissolved Solids), DO (Dissolved Oxygen) or salt content. Using the included conductivity/TDS/salt probe, an optional DO probe, and optional ORP or pH electrodes the meter can measure pH from 0 to 14, ORP from -1999 mV to 1999 mV, conductivity up to 200 mS (milliSiemens), TDS up to 132,000 ppm, DO up to 20 mg/L, and salt content up to 12% by weight.The HHWT-SD1 is designed for water conditioning, waste-water monitoring, beverage production, aquaculture (fish farming), aquariums, pulp and paper processing,electroplating, and photography applications. A front-panel pushbutton enables rapid switching among the meter’s four measurement modes.Because it is microprocessor-based, the HHWT-SD1 is portable, reliable and has the large storage capacities that SD memory cards offer. Measurements can be made automatically at any sampling rate between one second and nine hours. After time-stamping and storing the measurements on an SD card plugged into the meter,the user can remove the card and plug it into to a computer either directly or via a USB card reader. The values are stored on the card as files with the .xls extension, which can be opened by Microsoft’s Excel ® application.SpecificationsDisplay Size: 52 x 38 mm (2.05 x 1.5")Measurement Range:pH: 0 to 14 (probe sold separately)ORP: -1999 to 1999 mV (probe sold separately) Conductivity: Up to 200 mS (microSiemens) TDS: Up to 132,000 ppmDO: Up to 20 mg/L (probe sold separately) Salt: Up to 12% by weight Measurement Accuracy:pH: ±(0.02 pH units + 2 digits) (probe sold separately)ORP: ±(0.5% of reading + 2 digits) (probe sold separately) Conductivity: ±2% of full-scale reading + 1 digit TDS: ±2% of full-scale reading + 1 digit Temperature: ±0.8°C/±1.5°FDO: ±0.4 mg/L in solution (probe sold separately)Oxygen: 0.1% for oxygen in air (probe sold separately) Salt: ±0.5% of valueTemperature Compensation: Automatic between 0 and 65°C (32 and 150°F) with optional ATC temperature probe. Manually settable between 0 and 100°C (32 and 212°F) without ATC probe Settable Parameters: Date, time, auto power off, beep sound, sampling time, decimal point or comma decimal division, temperature unit, compensation temperature. Also salt and altitude compensation (DO mode only)Operating Temperature: 0 to 50°C (32 to 122°F)Meter Dimensions: 135 H x 60 W x 33 mm D (5.31 x 2.36 x 1.30") Weight: 35 oz (2.19 lb)carrying case, 2 GB SD memory card and operaror’s manual (solutions sold separately).Ordering Example: HHWT-SD1, data logging water test meter with PHE-1311, pH electrode and PHA-4, pH 4 buffer solution.HHWT-SD12 GB SD memory card included.Conductivity/ TDS/salt probe (included).。

数据采集设备操作使用说明书

MDR-8.07 移动数据记录器操作使用说明书北京京南航天数据技术有限公司目录1简介 (4)1.1用途 (4)1.2主要特点 (4)1.3 主要技术指标 (4)1.4设备组成 (4)1.4.1电源适配器 (5)1.4.2 MDR采集器 (5)2MDR软件安装 (7)2.1 硬件驱动安装 (7)2.2 MDR控制软件安装 (8)2.2.1软件安装条件 (8)2.2.2软件安装 (8)3MDR列表配置 (12)4MDR系统连接 (15)4.1 USB连接 (16)4.2网络连接 (16)4.3串口（RS422）连接 (17)5控制软件主界面 (17)5.1 菜单项 (19)5.1.1 系统配置 (19)5.1.2 数据操作 (19)5.1.3 数据显示 (21)5.1.4 应变调整 (21)5.1.5 标定 (22)5.1.6 其他菜单 (22)5.2 工具栏 (23)5.3 控制面板 (23)5.4 显示窗口 (24)6参数设置 (25)6.1 参数设置界面 (26)6.2 统一参数 (28)6.3 滑动平均 (28)6.4 触发类型设定 (29)7数据传输 (29)7.1 通道选择 (32)7.2 数据传输 (32)7.3 图形显示开关和显示图形延时 (32)7.4 图形操作 (33)8传感器标定 (33)9MDR数据采集步骤 (36)9.1 MDR连接 (36)9.2 MDR列表配置 (36)9.3 参数设置 (38)9.4 数据实时显示 (38)9.5 数据采集 (39)9.6 数据传输 (40)1简介1.1用途移动数据记录器 (Moving Data Recorder) 简称MDR，是北京京南航天数据技术有限公司自主研制具有国际领先水平的高技术产品；能够记录冲击、噪声、振动、速度、位移、过载、应变、陀螺、温度、压力、数字等多种信号，适用于恶劣环境下的动态、静态数据采集记录；广泛应用于桥梁、铁路、风能、教学、煤炭机械、特种设备、汽车碰撞、运输实验、分离实验、爆炸试验、摩拖车颠簸、飞行试验中的系统测量和设备检测等领域。

高速串口记录仪说明书.

使用说明产品简介串口数据记录仪是一种串口数据存储设备。

采用高速ARM控制芯片,将串口RS-232电平,以文件的方式透明的记录在存储介质中。

当使用记录后的数据时,可以通过模块自身的USB2.0接口高速上传到电脑上。

产品用途:l工业现场需要长时间记录数据,且定期后数据分析;l产品开发过程中,试验产品过程监控;l数据黑匣子备份;l……产品特点:l FAT32文件系统,方便WINDOWS识别;l文件自动建立,文件名编号支持9999;l透明串口记录,无需协议;l宽电压输入(7-35V,具备电源防反接保护;l双路电源输出,DB9第9针为备用电源输入端;l自动的记录方式,断电自动保存;l灵活的定时存储功能;l直观的声光提示功能,避免了盲目的数据记录;产品技术参数l电源参数:7-35V,典型工作电流12V、45mA;l数据接口:RS232;l8位数据位,1位停止位,无奇偶校验位的模式;l串口速率:4800、9600、19200、38400、115200、230400、256000、460800(接受订制l产品尺寸:90*54*28mm (长*宽*高mm产品清单:串口数据存储模块 1个USB数据线 1个工作说明SD卡内容配置操作说明:SD里面有个config.ini的,用记事本可以打开,有3项可以配置。

BPS:8/********下面是数字对应的波特率*********************/BPS为串口通信波特率设置参数为1 4800;2 9600;3 19200;4 38400;5 115200;6 230400;7 256000;8 460800MODE:1/********MODE 恒为 1*********************/TIME:1/********下面是数字对应的单个文件记录的时间长度,可以有根据单个文件大小进行设置*/1 30分钟2 1小时3 2小时4 4小时5 6小时6 8小时7 12小时8 24小时9 48小时工作说明:系统上电后:蜂鸣器长响一下自检通过,之后短响一次为开始记录。

GS8204SD双SD卡车载录像机说明书

目录1 注意事项 (2)2 产品规格 (3)3产品外特性 (5)遥控器利用说明 (5)MDVR接口概念 (7)电源线 (7)........................................................................................................................... 错误!未定义书签。

5系统用户登录.. (9)6主菜单 (10)系统设置 (11)大体设置 (12)时刻设置 (12)开关机设置 (13)系统保护 (14)系统信息 (16)录像功能 (17)录像设置 (17)按时录像设置 (19)报警功能 (21)报警处置 (21)IO报警 (22)移动侦测设置 (22)视频遮挡 (23)区域遮盖 (24)治理工具 (25)磁盘治理 (25)输出显示 (26)密码治理 (27)云台设置 (27)日记查询 (28)车辆治理 (29)大体信息 (29)速度设置 (30)加速度设置 (30)温度设置 (31)GPS设置 (31)网络效劳 (32)网络设置 (33)网络效劳 (35)无线设置 (37)WIFI设置 (38)邮箱设置 (39)7 I/O 报警输入输出说明 (40)1 注意事项安装和利用之前，请必然详细阅读利用说明书，以便您能正确利用和爱惜您的机械。

本说明书前脸部份为注意事项和安装利用介绍，请先行阅读。

➢注意事项●为保障您的权益，在安装利用本产品前，请认真阅读本手册内容。

●本产品为车内利用设备，为了避免短路或电击危险，请勿将本机放在雨中或潮湿的环境中。

●万一任何固体或液体进入机箱内，请当即断开机械电源，并请有资格的技术人员检查后方可再启动。

●本产品属于高科技设备，机内几乎没有效户自己能够修理的原件部份。

发生故障时必需请有资格的技术人员来检修，或与经销商联系。

➢安装环境●本录像机利用直流12～36伏电源，在利用前必需确认本地的电源电压；●若是长期不利用机械，最好完全断开录像机电源；●请选择适当的安装位置，以便使空气能在机械周围自由流通，以避免机械过热；●机械不可安装在散热器、通风道等热源周围，或有直射阳光、过量尘埃、或会发生机械振动或冲击的地址。

数据记录仪说明书

转换成其他数据格式
软件提供将所下载的数据保存为其他数据格式。如记录仪文件，Access文件，Excel文件，Word文件，文本文件。
具体操作点击保存会弹出（图7-5）
图7-5
选择以“文件方式保存”（图7-6）
图7-6
在保存类型下拉框选择需保存的数据类型。
选择将“数据附加到数据库”（图7-5）保存类型直接保存为Access文件。
刷新：当记录仪无法正常启动，一直处于停止状态时，可用“刷新”启动记录仪。
高级命令：工程模式，使用请询问厂家。
视图
工具栏：
图6-2
状态栏：
图6-3
属性栏：
图6-4
实时数据采集窗口：
图6-5
层叠窗口：排列窗口成互相重叠
水平平铺：水平方向排列窗口成互不重叠
垂直平铺：垂直方向排列窗口成互不重叠
重排图标：窗口恢复原始排列
图6-11
关于：查看软件信息
图6-12
工具栏功能说明
打开：打开一个现有的文档资料
另存为：将活动文档以一个新文件名保存
打印：打印文件时的打印机的程序设置并打印文件
七、具体操作指南
点击桌面上的图标进入设置界面，点击“连接 ”后这时左面的记录仪属性可以见到以下画面。（如图7-1）
图7-1
用户在这个界面上可对数据记录仪进行各项参数的设置
2、产品简介
针对以上这些情况我厂研制开发的精鹰牌ZDR系列固态数据记录仪，汲取国外同类产品优点并结合我国特点自主设计，可对温度、湿度、照度等进行记录。采用内置或外接各种传感器，采用单片机对外部数据进行采样，并将采样数据保存在系统不挥发存储器内。
固态数据记录仪采用高能锂电池供电，无需外部电源，体积小巧便于携带（58×72×29）mm，整机功耗小，可连续工作3年以上（视工作情况而定）。固态数据记录仪采用系列化设计，记录仪的基本型为单路数据采集、记录，复合型为多路数据采集记录，显示型为在基本型、复合型采集器基础上可用LCD进行实时数据显示。

Omega OM-DAQXL 8 16通道多功能数据记录仪说明书

8 or 16 Channel UniversalInput Touch Screen Data LoggerU 7" Touch Screen TFT Display U 8 or 16 Analog Channel Inputs U 8 Digital I/O (4 Inputs, 4 Outputs)U I IoT-Ready Through OPC UA/DA via Omega Enterprise Gateway U C loud-Ready Through MQTT via Omega Enterprise Gateway U M easures Voltage, Current, Thermocouples, RTDs, Thermistors, Strain Gage, Frequency and Pulse U 24-Bit Analog Input Resolution U F ast Sampling Rate–125 Samples/Sec (1 Channel)U 4 Alarm Outputs U L arge Data Storage: 1 GB Internal Memory, 32 GB SD Card or 32 GB USB Drive U U SB Device (PC Communication) and USB Host (USB Drive, Mouse, etc.)U P owers from Rechargeable Lithium-Ion Battery and/or AC Adaptor U B enchtop or Wall Mount Enclosure with Protective Rubber Boot DesignOM-DAQXL shownsmaller than actual size.Stylus (included).OM-DAQXL is an 8 or 16 channel analog input portable data logger with a 7 inch resistive touch color display. All inputs are programmable and can be configured for millivolts, volts, milliamps, thermocouple, RTD, thermistor, strain gauge, or frequency. All the menus, selections, and configurations can be done from the display touch screen. The unit also has 4 digital inputs, 4 digital outputs, 4 alarm outputs, one USB host port and one USB device port. The unit also has 3 LEDs for different indications (Power, Alarm and Logging).The OM-DAQXL comes complete with protective rubber boot, rechargeable lithium ion battery, 32 GB SD card, one plastic stylus, 1 GB USB thumb drive, 1.8 m (6') USB cable, 1.8 m (6') digital I/O cable, alarm/excitation terminal block, universal AC adaptor, screwdriver, quick start guide, set of 5 PTFE insulated Type K thermocouples, set of 5 ferrites to install on the thermocouple inputs (for noise reduction) and crimp-on ground lug. The unit can be wall mounted using the provided keyhole mount or operated on a bench using the tilt stand. The USB Wi-Fi Dongle will come in a separate package for '-EW' Models.Data display areaLine graph display.Digital display.Home ScreenThe home screen is the main screen of the datalogger’s user interface. It is divided into 3 distinctsections as shown below.Digital Display ViewStatus/Information Display: This status bar providesinformation such as Battery Charge percentage,System Clock (displays current Time & Date), Lock/Unlock data logger, status of the 4 Alarm Outputs, andLogging Mode indication.The OM-DAQXL comes complete with hard carrying case,protective rubber boot, rechargeable lithium ion battery, 32 GBSD card, one plastic stylus, 1 GB USB thumb drive, 1.8 m (6')USB cable, 1.8 m (6') digital I/O cable, alarm/excitation terminalblock, universal AC adaptor, screwdriver, quick start guide, setof 5 PTFE insulated Type K thermocouples, set of 5 ferrites toinstall on the thermocouple inputs (for noise reduction) andcrimp-on ground lug. Not all items shown. See User Guide forinstructions on installing ferrites on the thermocouple inputs. Data Display Area: This is the area where differentinputs (up to 4 Channels) are displayed vs. time.The data is displayed in 4 different ways: Waveform,Waveform & Table, Table only, and Digital. In the Digitalview, each channel name and number are displayedalong with the value.Navigation Toolbar: This toolbar provides accessto all the functions and menus of the data logger.Y ou can extend or retract the toolbar by pressing theTool button. The following flow chart shows all thefunctionalities of the buttons of the toolbar.OM-DAQXL shown smaller than actual size.Standalone OperationThe OM-DAQXL’s touch screen user interface (UI)makes configuring the data logger for operationstraight forward and simple. Recorded data files caneasily be reviewed and analyzed on the OM-DAQXL.For data analysis on a computer, simply transfer thedata file from the SD card or USB thumb drive to thePC and open the selected data file into Excel® or otherdata analysis software.Toolbar FlowchartBack view, OM-DAQXLALARM, EXTERNAL TRIGGER & 24VLeft side view, OM-DAQXLRight side view, OM-DAQXLTop view, OM-DAQXLBottom view, OM-DAQXLFront view, OM-DAQXLETHERNET PORTUSB HOST PORTSHELL GROUND USB DEVICE PORTEthernet Port only available for -EW modelsSpecificationsScreen: 7 inch, TFT, resistive touch comes with plastic stylus Rubber Boot: Black4 Channels: 25 s/sec8 Channels: 10 s/sec16 Channels: 5 s/secLogging Rate: 125 s/sec (Max) to 1 s/hour (Min)Maximum Logging Rate per Number of Channels (Analog and Digital):1 Channel: 125 s/sec2 Channels: 50 s/sec4 Channels: 25 s/sec8 Channels: 10 s/sec16 Channels: 5 s/secExcitation to Power External Transmitter: 24 Vdc @ 50 mA output–set in data session settingFilter Options: Per channel selectable moving average filter: None, 2, 5, 10, 20 or 50 samplesNumber of Samples for Moving Average Filter per Channel: Up to 50 samplesMath (Virtual) Channels: 8 or 16Digital Inputs: 4 Schmitt trigger based inputsRange: 0 to 24 Vdc single-endedLogic High Threshold: 2.5V Alarms per Channel: T woAlarm Types: High, low, windows in, windows out, open sensor Alarm Latching: Settable in alarm menuOn Alarm Event: Map to 4 alarm outputs, take screen shot, sound buzzerLogging Conditions: On command or based on trigger conditionsStart and Stop Trigger Conditions: Timer, date and time, weekday and time, alarm output, external triggerMemory:Internal: 1 GBSD Card: 32 GBUSB Drive: 32 GBUSB Ports: One host and one deviceEthernet*: 10/100 Base-T, TCP/IPUSB Wi-Fi Dongle*: 802.11 b/g/n, USB 2.0 interface, up to 150 Mbps, WEP and WPA/WPA2 encryption schemes*Only available on -EW models.Battery: Rechargeablelithium-ion;**********Battery Life: 4 to 8 hours based on display settingDC Adaptor: 12 Vdc @ 5AOperating Environment: 0 to 50°C (32 to 122°F), 0 to 95% RH non-condensingGeneral Dimensions: 28.6 L x 15.24 H x 6.35 cm D(9 x 6 x 2.5")Note: Measurement accuracy is at room temperature after 30 minutes* Insert country code.Comes complete with hard carrying case, protective rubber boot, 32 GB SD card, 1 GB USB thumb drive, 1.8 m (6') USB cable, 1.8 m (6') digital I/O cable, alarm/excitation terminal block, universal AC adaptor, screwdriver, quick start guide, set of 5 PTFE insulated Type K thermocouples and crimp-on ground lug. USB Wi-Fi dongle will come in a separate package for -EW models.Ordering Example: OM-DAQXL-1-NA,8-channel touch screen data logger with USB host/device.OM-DAQXL with protective rubber boot removed(included). Shown smallerthan actual size.-EW models are compatible with USB Wi-Fi dongles that support Windows Embedded Compact 7.0.。

QYFAT1_U盘读写模块TXT记录仪串口开发说明

一、简介芯片支持FAT、FAT32文件系统，其他文件系统都不支持。

所以很轻易的读取设备的内容。

这里我们支持U 盘、TF 卡、SPIFLASH 这三种设备。

TF 卡和U 盘最大支持128G 的容量。

当然兼容性是非常非常好的，基本所有的都支持。

选择的设备的时候，如果不需要很大的容量，可以选择spiflash 作为存储设备。

使用U 盘的时候，请注意，U 盘的供电电压，很多需要4.2V 以上。

TF 卡则不需要，3.3V 就足够了供电电压3.2V--5.2V 适用场景：1、文件记录器，支持FAT 或者FAT322、支持TXT 或者CSV。

或者自定义文件后缀名3、支持最大128G 的U 盘或者TF 卡，最大16M 字节的spiflash [W25Q128]。

三个设备任选一个。

U 盘优先【但是有的U 盘上电特别慢，也会是个问题】4、支持方案级芯片出货5、可定制各种特设的功能，前提是要有量电流10mA [无设备插入状态下]产品类型QYFAT 读写U 盘、TF 卡、SPIFLASH 设备型号KT1025A 尺寸32*20【mm】重量20g 接口串口uart[默认115200bps]波特率串口AT 指令可设产品特点说明：1、单芯片集成U 盘读写、TF 卡读写、spiflash 读写。

并且集成FAT、FAT32文件系统2、单芯片支持USB 连接电脑，充当读卡器使用。

可以连接电脑读TF 卡和SPIFLASH 3、超低的成本，超简单的外围元件4、芯片内置3.3V 的LDO 。

超宽的供电电压范围5、芯片的GPIO 电压，都是3.3V 的TTL 电平6、当开启写文件功能之后，芯片就处于默认透传模式，即串口收到的数据，追击写入指定的文件中7、串口波特率可修改，AT 指令即可。

当然芯片可以定制各种各样的功能新增程序升级功能，将“updata.bfu”拷贝至TF 卡或者U 盘，然后插入到模块中双击“PP”按键，就进入升级模式，升级完成灯熄灭，模块自动复位然后将设备中的“updata.bfu”文件删除，避免重复升级---定制型的客户用得到二、详细说明2.0硬件说明1、Microusb接口，只能供电。

USB数据记录仪操作手册(版本：1.31)说明书

Operation Manual of USB Data Logger(Version: 1.31)1. Introduction: (3)1.1 Features: (3)1.2 USB temperature data logger: (3)1.3 LCD symbols display instructions: (4)1.4 USB temperature humidity data logger: (4)1.5 LCD symbols display instructions: (5)1.6 Button instructions: (5)1.7 Install battery: (5)1.8 Install USB data logger: (6)2 Quick Start (7)3 Connecting the Logger to PC (7)4. Setting Up the Logger to Record Data (8)5. Download data from the logger (10)6. Delete all the logs from the logger (11)7. Data Listing Window (11)8. Exporting Logger Data (12)9. File List (13)1.Introduction:HE170 USB series has USB interface, enjoying elegant appearance and compact construction, specially designed for refrigerator and cold-chain transportation as well as container transport applications. HE170 USB series adopts friendly USB interface, friendly mounting bracket and the screws. HE170 USB series can show temperature/temperature and humidity simultaneously as well as the battery indication. The OK key can help to check the Max/Min/Current value and the upper and lower limits.1.1Features:l Waterproof and dustproof standard IP67, resisting moisture, dew-point temperature and dust.l Temperature and humidity limit can be set. LED lights when the setting value being exceeded.l Ultra-lower consumption design, 1/2AA 3.6V Li battery, working for 12 months and easy to install your battery.l Transfer logging data to PC through software and can be saved as different types to ensure the existence.l Adopt high sensitive sensor, enjoy fast response and high accuracy.1.2USB temperature data logger:8①LCD display②Button③LED warming light when the temperature value exceeds the setting limits.④USB connection port.⑤Waterproof ring.⑥Battery replacement position.⑦Waterproof transparent cover.⑧Fixed bracket.1.3LCD symbols display instructions:①HI symbol display shows being the temperature upper limit setting status.②LO symbol display shows being the temperature lower limit setting status.③Battery power indication.④MIN symbol display shows being the minimum temperature value checkingstatus.⑤MAX symbol display shows being the maximum temperature value checkingstatus.⑥LOG symbol display shows being the logging status.⑦（Celsius and Fahrenheit）⑧Temperature value symbol display.1.4USB temperature humidity data logger:8①LCD display.②Button.③LED warming light when the temperature and humidity values exceed thesetting limits.④USB connection port.⑤Waterproof ring.⑥Battery replacement position.⑦Waterproof transparent cover.⑧Fixed bracket.1.5LCD symbols display instructions:①HI symbol display shows being the temperature and humidity upper limitssetting status.②LO symbol display shows being the temperature and humidity lower limitssetting status.③MAX symbol display shows being the maximum temperature and humidity valueschecking status.④MIN symbol display shows being the minimum temperature and humidity valueschecking status.⑤Battery power indication.⑥Units symbol display:（Celsius and Fahrenheit）humidity unit⑦Temperature and humidity values symbol display.1.6Button instructions:1.6.1：Press this button for long to 5seconds can turn on/off thecancheck the MAX, MIN, High and low warming limits values as well as the current value under the working status.1.7Install battery:1.7.1Firstly, use your tool ① to open the battery back cover ②, then installyour battery ③.1.8 Install USB data logger:1.8.1 Use screw ② to fix the bracket ① onto the wall and then install the datalogger as follows:2Quick StartFollow the procedure below to quickly start using your data logger:1. Connect the data logger to a free USB port on the computer.2. Start T oAnalyzer U software on the PC.3. From the toolbar select Connect.4. Then you can setup or download data, delete data from the logger.5. Unplug the cable from the logger, and then the logger is in stop mode.6. Press OK for about five seconds, the logger will be power on (LOG mode) or off (OFFmode).Note: The logger has three modes:1. LOG: In the mode, the logger samples and records data timely.2. OFF: In this mode, the logger stops to sample and record, and the LCD display is off. 3Connecting the Logger to PCT o connect the logger to the computer, follow these steps:1. Connect the USB cable to the logger and to a free USB port on the computer.2. If you are connecting the logger to the PC for the first time, the logger willautomatically be recognized and installed on the computer.3. Start T oAnalyzer U analysis software.4. Click the icon4.S etting Up the Logger to Record DataT o set the logger to start recording data, click thel: Synchronize the PC time to the logger.l Name: Gives a name to the logger.l Type: The device type.l Model: The device model.l Serial No: Every logger has a SN with 10 characters. The length must be 10.l LOG Intervals(s): The interval of recording.l Log Count: The count of the logs that the logger has recorded.l Memory capacity: The total capacity of the logger memory. One reading includes time and three channels’ data.l T emperature Unit: The selection of C and F.l Start Mode: There are three start modes: No Delay / Delay / Timer.No Delay: The logger will start to log immediately.Delay: The logger will start to log after a delay time.Timer: The will start to log at a specific time.Note: If the logger is OFF, the logger cannot record any logs.Calibrate the logger: The logger is factory calibrated to an accuracy given in the device specifications. However, there may be times when you wish to adjust the calibration of your logger. T oAnalyzer provides you with the ability to perform a single point offset calibration. This calibration can be used to increase the accuracy of the logger for a restricted data range.l CH1 offset: The offset of channel one.l CH2 offset: The offset of channel two. (If the logger is temperature logger, the CH2 and CH3 are useless.)l CH3 offset: The offset of Dew Point.5.D ownload data from the logger.T o get the recorded logs from the logger, connect the logger to your computer and clickthe6.D elete all the logs from the logger.T o erase all data from the logger, connect to the logger, and then clickbutton on the toolbar, and then the data listing window is shown below.The data pane lists the data samples collected by the logging device.The column width of each column is adjustable by using the left mouse button and dragging the column the desired width.8.E xporting Logger DataY ou can use ToAnalyzer to export sample data to a text file or to a Microsoft Excel file or BMP file.ll。

CAN 记录仪使用手册说明书

诚至科技简洁而不简单使用手册CAN 记录仪手册UM20230605 V2.02Date:2023/06/05CAN 记录仪使用手册类别内容关键词 CANRecorder ，CANReplayer ，记录仪摘要CAN 记录仪、回放仪使用手册。

User Manual目录1. 适用范围 (1)2. 硬件介绍 (1)2.1设备外观 (1)2.2设备参数 (2)2.3设备接口定义 (2)2.4设备模式 (3)2.5固定挡板介绍 (6)2.6指示灯介绍 (7)3. 驱动安装 (7)4. CANBetter设置软件简介 (10)4.1软件概述 (10)5. CANRecorder（CAN记录仪模式）使用步骤 (12)5.1使用配置 (12)5.2CAN数据记录 (12)5.3CAN记录导出 (12)5.4CAN数据分析 (12)5.5利用CANoe分析数据 (13)5.6利用CANTracer软件分析 (13)6. 故障排查及注意事项 (14)6.1主要故障排查 (14)6.2注意事项 (15)7. 售后与保修 (16)8. 供货清单 (17)9. 免责声明 (17)1. 适用范围本公司的CANBetter系列产品包括：总线记录仪（又名为CanRecorder）、CAN总线数据回放仪（又名CanReplayer）、CAN总线网桥（又名为CanBridge）。

根据您所买的设备型号的不同，包含的功能可能有所不同。

请根据所选设备型号，参考相应功能介绍。

该设备包含两路独立CAN通道。

对于CanRecorder或CanReplayer，出厂默认配置8G~32G SD卡（根据客户购买时选择），用于记录CAN总线上收到的数据或回放数据。

典型应用■CAN-bus网络诊断与测试■汽车电子应用■电力通讯网络■工业控制设备■高速、大数据量通讯注意：下面所涉及设备图片、软件设置界面根据不同的产品型号可能会略有差异，请以实际设备型号为准。

SD卡使用手册

SD卡使用手册第1章 SD软件包使用手册SD/MMC 卡是一种大容量（最大可达4GB）、性价比高、体积帏、访问接口简单的存储卡。

SD/MMC 卡大量应用于数码相机、MP3 机、手机、大容量存储设备，做为这些便携式设备的存储载体，它还具有低功耗、非易失性、保存数据无需消耗能量等特点。

SD 卡接口向下兼容MMC（MutliMediaCard 多媒体卡）卡，访问SD 卡的SPI 协议及部分命令也适用于MMC 卡。

1.1 SD/MMC卡的外部物理接口SD 和MMC 卡的外形和接口触点如图1 所示。

其中SD 卡的外形帺寸为：24mm x 32mm x 2.1mm （普通）或24mm x 32mm x 1.4mm （薄SD 存储卡），MMC 卡的外形帺寸为24mm x 32mm x 1.4mm 。

表1 为SD/MMC 卡各触点的名称及作用，其中MMC 卡只使用了1 ~ 7 触点。

表1 SD/MMC 卡的焊盘分配滨：1. S：电源；I：输入；O：推挽输出；PP：推挽I/O。

2. 扩幕的DAT 线（DAT1 ~ DAT3 ）在上电后处于输入状态。

它们在执行SET_BUS_WIDTH 命令后作为DAT 线操作。

当不使用DAT1 ~ DAT3 线时，主机应使自己的DAT1~DAT3 线处于输入模式。

这样定义是为了与MMC 卡保持兼容。

3. 上电后，这条线为带50KΩ上拉电阻的输入线（可以用于检测卡是否存在或选择SPI 模式）。

用户可以在正常的数据传输中用SET_CLR_CARD_DETECT（ACMD42 ）命令断开上拉电阻的连接。

MMC 卡的该引脚在SD 模式下为保留引脚，在SD 模式下无任何作用。

4. MMC 卡在SD 模式下为：I/O/PP/OD。

5. MMC 卡在SPI 模式下为：I/PP。

由表1 可见，SD 卡和MMC 卡在不同的通信模式下，各引脚的功能也不相同。

这里的通信模式是指微控制器（主机）访问卡时使用的通信协议，分为两种：SD 模式及SPI 模式。

Testo 184 数据记录仪使用手册说明书

4
2 说明
特征
电池寿命（可重复使用的数据记录仪）
工作时间（一次性数据记录仪）
数值 T3：500 天（15 分钟测量周期，25°C） T4：100 天（15 分钟测量周期，-80°C）
T1：90 天，第一次程序开始（5 分钟测量周期，-35°C） T2：150 天，第一次程序开始（5 分钟测量周期，-35°C
· 单个警报：超过设定的限制值时触发一个警报。
· 累计警报（仅用于温度和湿度测量）：不会在第一次超过设定限制值时就触发警报，而是当超过限制值的总时间超过了设定的等待时间（允许时间）时才发出报警。
· 壁挂支架（供货类型 G1）：为了加速测量，必须将数据记录仪牢固地附着到需监视的对象。使用 2 颗螺钉或 2 根扎带固定壁挂支架，然后将数据记录仪推入壁挂支架。
测量参数温度 [°C，°F]
[单位]
测量范围精度
分辨率工作温度储藏温度电池类型
T1，T2，T3：-35～70°C T4：-80～70°C T1，T2，T3：±0.5K T4：±0.8K（-80～-35.1°C) ,±0.5K（-35.0～ 70°C) 0.1°C
T1，T2，T3：-35～70°C T4：-80～70°C T1，T2，T3：-35～70°C T4：-80～70°C T1：内置的，不可更换 T2：内置的，不可更换 T3：CR2450，可更换 T4：TLH-2450，可更换
时工作时间>12 小时），请通过网站联系我们：https:///zh-CN/services/service-overview
重新恢复传感器：在<20％RH 和 50°C 时则每 12 小时；在 40～60％RH 和 20～30 时则每 24 小时。

Extech SDL700 压力计 SD 卡实时数据记录仪用户指南说明书

USER GUIDE Pressure MeterSD Card real-time dataloggerModel SDL700IntroductionCongratulations on your purchase of the Extech SDL700 Pressure Meter, an SD Logger Series meter. This meter displays and stores pressure readings from optional pressure sensors in the range of 30, 150, 300 psi. Supported measurement units are bar, psi, Kg/cm2, mm Hg, inch Hg, meters of H2O, inches of H2O, atmosphere, hPA, and kPA. Logged data readings are stored on an SD card for transfer to a PC. In addition, an RS232 port allows data streaming to a PC. This meter is shipped fully tested and calibrated and, with proper use, will provide years of reliable service. SafetyInternational Safety SymbolsThis symbol, adjacent to another symbol or terminal, indicates the user must refer to themanual for further information.Meter Description1. Pressure Sensor input jack2. Measurement reading on LCD DisplayBacklight keyand3. HOLDkey4. MAX-MIN5.6. PC interface jackbutton7. Reset8. Power Adaptor jack9. SD card slot10. ENTER and LOG key11. Down arrow ▼ key12. Up arrow ▲ / UNIT key13. Power ON-OFF key14. Unit of measure on the LCD DisplayNotes: Items 6, 7, and 8 are located behind the snap-off compartment cover on meter’s right side. Battery compartment, tilt stand, and tripod mount are located on the rear of the instrumentGetting StartedPower ON-OFF∙Power the meter by pressing and holding the power button for at least 1.5 seconds.∙Press and hold the power button for at least 1.5 seconds to power OFF the meter.∙This meter is powered by six (6) 1.5VDC ‘AA’ batteries or by optional AC adaptor. If the meter will not switch ON please check that fresh batteries are installed in the rear battery compartment or, in the case of the AC adaptor, check that the adaptor is connected correctly to the meter and to an AC source.Display BacklightTo turn the display backlight ON or OFF, press and hold the backlight button for at least 1.5 seconds. The meter will beep when switching the backlight ON or OFF unless the beeper isdisabled.Pressure SensorsPressure sensors are connected to the meter via the DIN jack at the top of the meter. Pressure sensors of 2Bar (30psi), 10Bar (150psi) and 20Bar are available for use with the SDL700.Note that re-calibration is not necessary when changing sensors; however the user must select the appropriate sensor range in the Setup Mode. To view the currently selected sensor range from the normal operation mode, press and hold the down arrow button ▼ for at least 1.5 seconds.Units of MeasureThe currently selected unit of measure is shown below the measurement value on the meter’s LCD.To change the unit of measure, press and hold the UNIT button until the desired unit of measure appears and then release the UNIT button. The meter begins scrolling through the available units of measure (see table below) after the UNIT button has been depressed for at least 1.5 seconds.INDICATORUNIT DISPLAYpsi PSIInch Hg In HgH2OInch H2O InhPA hPAkPA _PABar bArC2Kg/cm2 _gmm Hg --HgH2OMeters H2O -tAtmospheres AtPZERO AdjustmentTo null, or zero, the display for a connected sensor, press and hold the down arrow key▼ for at least 12 seconds.Data HoldTo freeze a displayed reading on the LCD, momentarily press the HOLD button (the HOLD icon will appear above the reading). To exit HOLD, press the HOLD button again.Setup ModeBasic settings at a glanceTo view the current configuration of the meter with regard to time, date, and datalogging sampling rate press the SET button momentarily. The meter will now display the configuration in quick succession. If the information is missed on the first try, simply press the SET button again until all of the information is noted.Accessing the Setup mode1. Press and hold the SET button for at least 1.5 seconds to access the Setup menu.2. Press the SET button momentarily to step through the available parameters. The parametertype is shown on the bottom of the LCD and the current selection for that type is shown above it.3. When a parameter is displayed that is to be changed, use the arrow keys to change thesetting. Press the ENTER button to confirm a change.4. Press and hold the SET button for at least 1.5 seconds to exit the Setup mode. Note that themeter automatically switches out of the Setup mode if no key is pressed within 7 seconds.5. The available Setup parameters are listed below. Additional detailed information is providedbelow this list:dAtE Set the clock (Year/Month/Date; Hours/Minutes/Seconds)SP-t Set the datalogger sampling rate (Hours/Minutes/Seconds)PoFF Automatic power-off management (Enable or disable the auto-power off function)bEEP Set the beeper sound ON/OFFdEC Set the numerical format; USA (decimal: 20.00) or European (comma: 20,00)Sd F Format the SD memory cardtYPE Select the pressure range type (2, 5, 10, 20, 50, 100, 200, and 400 Bar)Setting the Clock Time1. Access the dAtE parameter.2. Use the arrow keys to change a value3. Use the ENTER button to step through the selections4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (orsimply wait 7 seconds for the meter to automatically switch to the normal operating mode).5. The clock will keep accurate time even when the meter is switched off. However, if the batteryexpires the clock will have to be reset after fresh batteries are installed.Setting the Datalogger Sampling Time (Rate)1. Access the SP-t parameter.2. The sampling rate can be set from ‘0’ seconds (manual log mode) up to 8 hours, 59 minutes,and 59 seconds.3. Use the ENTER button to move through the Hours, Minutes, and Seconds digit groups and usethe arrow keys to change the digit values.4. Press the ENTER button to confirm the entry.5. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (orsimply wait 7 seconds for the meter to automatically switch to the normal operating mode).Enabling/Disabling the Auto Power OFF FeaturePoFF parameter.the1. Access2. Use the arrow buttons to select ON or OFF. With the Auto Power OFF feature enabled, themeter will automatically switch OFF after 10 minutes of inactivity.3. Press ENTER to confirm setting.4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (orsimply wait 7 seconds for the meter to automatically switch to the normal operating mode).Set the Beeper Sound ON or OFFbEEP parameter.the1. Access2. Use the arrow buttons to select ON or OFF.3. Press ENTER to confirm setting.4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (orsimply wait 7 seconds for the meter to automatically switch to the normal operating mode). Numerical Format (comma or decimal)European and USA numerical formats differ. The meter defaults to USA mode where a decimal point is used to separate units from tenths, i.e. 20.00; The European format uses a comma, i.e.20,00 to separate units from tenths. To change this setting:1. AccessdEC parameter.the2. Use the arrow buttons to select USA or EUro.3. Press ENTER to confirm setting.4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (orsimply wait 7 seconds for the meter to automatically switch to the normal operating mode).SD Card FORMATTINGSd F parameter.the1. Access2. Use the arrow buttons to select YES to format the card (select NO to abort). Note that all dataon the card will be lost if formatting is attempted.3. Press ENTER to confirm selection.4. Press ENTER again to re-confirm.5. The meter will automatically return to the normal operating mode when formatting is complete.If not, press and hold the SET button for at least 1.5 seconds to exit to the normal operationmode.Set the Pressure Sensor Range Type (2, 5, 10, 20, 50, 100, 200, and 400 Bar) Note: Currently available sensors are: 30psi (2 Bar), 150psi (10 Bar) and 300psi (20 Bar)tYPE parameter.1. Accessthe2. Use the arrow buttons to select the desired sensor type3. Press ENTER to confirm setting.4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (orsimply wait 7 seconds for the meter to automatically switch to the normal operating mode). System ResetIf the meter’s keys become inoperable or if the display freezes the Reset button can be used to reset the instrument.∙Use a paper clip or similar item to momentarily press the reset button located on the lower right side of the instrument under the snap-off compartment cover.∙After pressing the Reset button, switch the instrument ON by pressing and holding the POWER key for at least 1.5 seconds. If using the power adaptor unplug the adaptor and then plug it back in again to power the meter.Max-Min Reading RecordFor a given measurement session, this meter can record the highest (MAX) and the lowest (MIN) readings for later recall.1. Press the MAX-MIN button momentarily to access this mode of operation (REC icon appears)2. The meter is now recording the MAX and MIN readings.3. Press the MAX-MIN button again to view the current MAX readings (MAX icon appears). Thereadings on the display are now the highest readings encountered since the REC icon wasswitched on (when the MAX-MIN button was first pressed).4. Press the MAX-MIN button again to view the current MIN readings (MIN icon appears). Thereadings on the display are now the lowest readings encountered since the REC icon wasswitched on (when the MAX-MIN button was first pressed).5. To exit the MAX-MIN mode, press and hold the MAX-MIN button for at least 1.5 seconds. Themeter will beep, the REC-MAX-MIN icons will switch off, the MAX-MIN memory will clear, and the meter will return to the normal operating mode.DataloggingTypes of Data Recording∙Manual Datalogging: Manually log up to 99 readings onto an SD card via push-button press.∙Automatic Datalogging: Automatically log data onto an SD memory card where the number of data points is virtually limited only by the card size. Readings are logged at a rate specified by the user.SD Card Information∙Insert an SD card (from 1G size up to 16G) into the SD card slot at the bottom of the meter. The card must be inserted with the front of the card (label side) facing toward the rear of the meter.∙If the SD card is being used for the first time it is recommended that the card be formatted and the logger’s clock set to allow for accurate date/time stamping during datalogging sessions.Refer to the Setup Mode section for SD card formatting and time/date setting instructions.∙European and USA numerical formats differ. The data on the SD card can be formatted for either format. The meter defaults to USA mode where a decimal point is used to separate units from tenths, i.e. 20.00. The European format uses a comma, i.e. 20,00. To change this setting, refer to the Setup Mode section.Manual DataloggingIn the manual mode the user presses the LOG button to manually log a reading onto the SD card.1. Set the sampling rate to ‘0’ seconds as described in the Setup Mode section.2. Press and hold the LOG button for at least 1.5 seconds and the DATALOGGER icon will appearon the LCD; the lower portion of the display will show p-n (n = memory position number 1-99).Note that if PSI is set as the unit of measure it appears as P51 (where a ‘5’ is used as an ‘S’) in the same area of the LCD where memory locations are shown. This can be disorienting at first.3. Momentarily press the LOG button to store a reading. The DATALOGGER icon will flash eachtime a data point is stored.4. Use the ▲ and ▼ buttons to select one of the 99 data memory positions in which to record.5. To exit the manual datalogging mode, press and hold the LOG button for at least 1.5 seconds.The DATALOGGER icon will switch off.Automatic DataloggingIn automatic datalogging mode the meter takes and stores a reading at a user-specified sampling rate onto an SD memory card. The meter defaults to a sampling rate of two seconds. To change the sampling rate, refer to the Setup Mode section (the sampling rate cannot be ‘0’ for automatic datalogging):1. Select the sampling rate in the Setup Mode to a value other than zero.2. Press and hold the LOG button for at least 1.5 seconds. The meter will flash theDATALOGGER icon at the selected sampling rate indicating that readings are now beingautomatically recorded to the SD card.3. If a card is not inserted or if the card is defective, the meter will display EMPTY and exit theDATALOGGER mode. In this case, switch the meter OFF and try again with a valid SD card.4. Pause the datalogger by pressing the LOG button momentarily. The DATALOGGER icon willstop flashing and the sample rate will display for a short time. To resume logging simply press the LOG button again momentarily.5. To terminate the datalogging session press and hold the LOG button for at least 1.5 seconds.6. When an SD card is used for the first time a folder is created on the card and named PSA01.Up to 99 spreadsheet documents (each with 30,000 readings) can be stored in this folder.7. When datalogging begins a new spreadsheet document named PSA01001.xls is created onthe SD card in the PSA01 folder. The data recorded will be placed in the PSA01001.xlsdocument until 30,000 readings are reached.8. If the measurement session exceeds 30,000 readings, a new document will be created(PSA01002.xls) where another 30,000 readings can be stored. This method continues for up to99 documents, after which another folder is created (PSA02) where another 99 spreadsheetdocuments can be stored. This process continues in this same fashion with folders PSA03through PSA10 (last allowable folder).SD Data Card to PC Data Transfer1. Complete a datalogging session as detailed in above in the previous sections. Hint: For thefirst few tests, simply record a small amount of test data. This is to ensure that the datalogging process is well understood before committing to critical, large scale datalogging.2. With the meter switched OFF, remove the SD Card.3. Plug the SD Card directly into a PC SD card reader. If the PC does not have an SD card slot,use an SD card adaptor (available at most outlets where computer accessories are sold).4. Power the PC and run a spreadsheet software program. Open the saved documents in thespreadsheet software program (see example spreadsheet data screen below).Spreadsheet data exampleRS-232/USB PC InterfaceFor streaming of data to a PC via the RS232 Output jack, the optional 407001-USB kit (RS232 to USB cable and driver CD) along with the 407001 software (available free at/sdl700) are required.AC Power AdaptorThis meter is normally powered by six (6) 1.5V ‘AA’ batteries. An optional 9V power adaptor is available. When the adaptor is used, the meter is permanently powered and the power button will be disabled.Battery Replacement and DisposalWhen the low battery icon appears on the LCD, the batteries must be replaced. Several hours of accurate readings are still possible in this condition; however batteries should be replaced as soon as possible:∙Remove the two (2) Phillips screws from the rear of the meter (directly above the top of the tilt stand).∙Remove and safely place the battery compartment and screws where they will not be damaged or lost.∙Replace the six (6) 1.5V ‘AA’ batteries observing polarity.∙Replace the battery compartment cover with the two (2) Phillips screws.All EU users are legally bound by the battery ordinance to return all used batteries tocollection points in your community or wherever batteries / accumulators are sold!Disposal in the household garbage is prohibited!SpecificationsGeneral SpecificationsDisplay Backlit LCD; LCD size: 52 x 38mm (2 x 1.5”)Status indicators Over-range audible beep and low battery display iconSensor types Accepts pressure sensors with 100mV full scaleAvailable sensors: 30, 150 and 300psiMeasurement Units Bar, psi, Kg/cm2, hPA, mm Hg, inch Hg, meters H2O, kPA, inchesH2O, ATPAccuracy (Meter) ± (0.5% reading + 1d) at ambient temperature 23°C (±5°C)Datalogger Sampling Rate AUTO LOGGING: From 1 second up to 9 hours.MANUAL LOGGING: Set the sampling rate to ‘0’ seconds Memory Card SD memory card; 1G to 16GB sizeData Hold Freeze the displayed readingMemory Recall Record and Recall the Maximum and Minimum readingsDisplay update rate Approx. 1 secondData Output RS-232 / USB PC computer interfaceOperating Temperature 0 to 50°C (32 to 122°F)Operating Humidity 85% R.H. max.Auto Power OFF A fter 10 minutes of inactivity (can be disabled)Power Supply Six (6) 1.5 VDC batteries (optional 9V AC adaptor)Power Consumption Normal operation (backlight and datalogger OFF): approx. 5mAdcWith backlight OFF and datalogging ON: approx. 25mAdcWith backlight ON add approx. 12mAdcWeight 343g (0.75 lbs.) w/ batteries; 241g (0.53 lbs.) w/o batteriesDimensions 182 x 73 x 47.5mm (7.1 x 2.9 x 1.9”)Transducer Range and Resolution TableSensor typePT30 PT150 PT300Max. Max. Max.Range Resolution Range Resolution Range Resolution200.020.010.002bar 2102900.20.20.02Psi 29145Kg/cm2 2.040 0.002 10.19 0.01 20.40 0.02 Hg 1500 2 7500 10 15000 20mminch Hg 59.05 0.05 295.2 0.2 590.5 0.5meter H20 20.40 0.02 101.9 0.1 204.0 0.2inch H20 802 1 4010 5 8020 10 Atmosphere 1.974 0.002 9.87 0.01 19.74 0.0220000201010000hPA 2000221000 120000.2kPA 200.0Transducer Accuracy PT30: ± (2%FS + 0.02 Bar)PT150: ± (2%FS + 0.1 Bar)PT300: ± (2%FS + 0.2 Bar)Overload protection 150% of max capacityCeramicDiaphragmSupply voltage 5VThread ¼” PS, 19 teeth per inchSpan (full scale) ± 1% (10 to 40ºC) includes linearity, hysteresis & repeatabilityZero ± 2% Full Scale (10ºC to 40ºC)Operating Temperature 32ºF to 140ºF (0ºC to 40ºC)Operating Humidity Max 80% RHOutput Full capacity output = 100 mV DCSize 30 mm diameter x 85mm(160g)5.65oz.WeightCable length 39” (1m)Copyright © 2013 FLIR Systems, Inc.All rights reserved including the right of reproduction in whole or in part in any form。

DATA-F211 串口数据记录模块使用说明书

商标声明：为唐山平升电子技术开发有限公司的注册商标。

本文档提及的其他所有商标或注册商标，由拥有该商标的机构所有。

注意：由于产品版本升级或其他原因，本文档内容会不定期进行更新。

除非另有约定，本文档仅作为使用指导，本文档中的所有陈述、信息和建议不构成任何明示或暗示的担保。

目录第一章产品简介 (1)1.1概述 (1)1.2产品特点 (1)1.3技术参数 (1)1.4产品外型 (2)1.5使用说明 (2)1.5.1 SD卡安装说明 (2)1.5.2 指示灯说明 (3)1.5.3 DB9引脚说明 (3)第二章产品使用前须知 (4)2.1概述 (4)2.2 开箱 (4)第三章通讯协议 (5)3.1通讯协议格式 (5)3.2存储文件形式 (5)第四章工具软件 (6)4.1工具软件介绍 (6)4.2使用方法 (6)第五章常见问题解决方法 (7)5.1常见故障分析与处理措施 (7)第一章产品简介1.1概述该产品为外部扩展的数据记录设备，用于公司产品外部扩展存储使用，采用12/24V供电，通过DB9接口进行数据通讯，属于外置配件范畴。

1.2产品特点本设计主要配合公司产品使用，即插即用，无需设参。

使用时只需要按照平升历史记录格式传输即可，模块会自动生成以日期为文件名的“.txt”的历史记录文件。

1.3技术参数⚫通讯口配置：默认9600bps，N，8，1 （RS232）*支持定制，最高波特率115200bps⚫供电：5~30V⚫支持文件系统：FA T32⚫数据记录文件格式：.TXT文本文件⚫支持SD卡类型：SDSC1.0版本（最大容量2G）；SDHC2.0版本（最大容量32G）；*SDXC卡（最大容量64G），需要先格式为FAT32文件格式再试用。

新车载SD卡车载录像机使用手册

车载数字高清录像机使用手册（单路二路四路通用）感谢您购买我们的产品。

请详细阅读本使用说明书，以便您能更好的使用和保护您的机器。

阅读后请将说◆本手册的制订过程中，已力求内容正确和完整◆产品请以实物为准，说明书仅供参考◆产品实时更新，如有升级恕不另行通知◆最新程序及说明文档敬请与公司客服人员联系◆产品说明中有疑问或争议的，以公司最终解释为准目录第一节：产品应用及规格参数....................................... ..3 第二节：产品接口定义及功能说明. (6)第三节：系统菜单操作说明 (9)设备启动及用户登录 (9)3.3系统设置................................................... .10 3.3-1基本设置. (11)3.3-2开关机设置.............................................. .11 3.3-3传感设置................................................ .11 3.3-4密码设置................................................ .11 3.4录像设置 (12)3.4-1常规设置 (12)3.4-2 通道设置 (12)3.4-3 定时设置 (13)3.4-4 移动侦测 (13)3.6管理工具.................................................. .14 3.6-1磁盘管理. (14)3.6-2配置管理 (14)3.6-3系统升级 (15)3.7录像管理 (15)3.8. 系统信息 (15)第四节：常用设置快捷操作 (16)4.1 接线测试及开机 (16)4.2 录像设置 (16)4.3 录像回放 (17)附录1:常见问题及处理 (17)售后服务条款 (18)第一节:产品应用及规格参数1.1：MDVR是专为车载视频监控和远程监控开发的一款高性价比、功能可扩展性强的设备。

RZMS-U9 PC记录仪规格书说明书

RZMS系列PC 记录仪机型: RZMS－U9T－①/MSR　①在下列代码中选择。

（例如: RZMS－U9T－M2/MSR）端子形状T: M3螺丝端子①供电电源◆交流电源M2: 100～240V AC (允许电压范围 85～264V AC、47～66Hz)◆直流电源R: 24V DC (允许电压范围 24V±10%、纹波系数 10%p-p以下)附加代码◆PC记录仪软件 (必须指定一项)/MSR: 附带　REM3－250 可直接连接在RZMS－U9的螺丝端子上，　但是由于发热会影响冷端补偿精度和标准精度，因此建议　您使用转接端子。

・组态软件（机型: RZMSCFG）　可从本公司的网站下载组态软件。

　将本产品连接到电脑时，需要专用的连接电缆线。

所需专　用电缆线的型号请参照本公司网站的下载网站或组态软件　的使用说明书。

　注）此软件的运作状况是在日文版与英文版OS上确认的。

・USB串口转换器（机型: USB－RSAQ□　I・ODATA机器产）・PC记录仪软件（CD 1盘）・电源、通信部分: 连接器型欧式端子盘　(适用电缆线: 0.2～2.5mm2 (AWG 24～12)、　露线长度为7mm)・RS-232-C: 9针D-sub接口 (阳型)　(固定螺丝 No.4-40 UNC)・输入信号、报警输出: M3螺丝端子连接　(紧固扭矩为0.6N·m)・设定器: 背面接口RS-232-C电平端子螺丝材质: 铁表面镀镍机壳材质: 灰色耐燃性树脂隔离: 输入1－输入2－输入3－输入4－输入5－输入6－输入7－输入8－输入9－输入10－输入11－输入12－触发输入－报警输出－RS-232-C・RS-485・设定器接口－电源端子－接地端子间零点和量程调整: 对于所有的输入类型，可根据应用情况进行零点和量程的调整。

(用RZMSCFG进行调整)熔断报警: 对于热电偶输入和热电阻输入，可以设定无熔断报警、上限报警和下限报警。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

串口SD卡数据记录仪关键词：数据记录仪采集器模块串口SD卡文件系统工业级1.概述SD卡数据记录仪（又名：串口转SD卡存储器，SD卡读写模块、RS232数据采集器）是一款智能调试模块。

本产品采用最新的32位ARM技术，内部建立文件系统和实时操作系统，实现高速可靠的文件管理，和通信控制。

本产品用途广泛，利用其存储功能，可以用于系统测试数据采集分析。

或者集成到您的设备中，使设备具有Sd卡文件系统读写功能，用于设备的数据存储。

产品是嵌入式系统、工业控制设备等数据采集、数据交互的利器。

只要通过RS232串口，就可以可以把数据存储在SD卡中的文件中，对SD卡中的文件进行各种操作。

图1DB9接口形式图2接线端子形式2功能特点数据记录仪可以自动分析收到的数据，根据数据特点智能切换使用方式。

设备使用方法有两种，分别如下：1、根据命令操作。

SD卡数据记录仪串口收到的所有数据会软件分析，如果数据符合通信协议，数据记录仪解析数据包内容后，作相应的处理，然后将结果从串口送出。

通信过程采用一发一答的方式，即主机主动发送数据到SD卡数据记录仪，SD卡数据记录仪才会发回应答。

该方法可以是文件的读取、写入和修改；以及文件夹和系统配置等操作。

2、透传存储，如果收到的数据不符合通信协议规范，数据记录仪会将串口收到的所有数据自动保存到自动生成的文件中，该方法只能保存串口接收到的数据。

每次开机启动，设备会自动建立一个默认的用于存储的文件。

文件名称为“MMDDHHMM.txt”(MM月份，DD日期，HH小时，MM分钟）。

改方式下，可以设置是否自动建立文件，已经建立文件的时间间隔或者是否添加时间戳到数据中。

SD卡数据记录仪内建立三个文件操作的句柄（分别为0,1,2），即同时可以打开对3个文件，并进行操作。

其中最后一个文件句柄2，用于控制直接存储的文件写入操作。

如果用户同时使用上述直接存储和命令操作，则应避免使用文件句柄2，否则会影响直接存储的文件操作，造成数据混乱。

数据记录仪特点如下：1体积小，重量轻，使用方便。

2功能强大，海量存储，支持FAT、FAT16、FAT32文件系统，支持带分区的SD卡，支持SDHC标准，SD卡容量可达32G！3读写速度快，实时操作系统支持，ARM7硬件平台。

4开放接口，只要使用简单的协议，就可以进行复杂的文件操作。

5支持文件夹建立操作。

电路设计。

铝合金外壳，防护更加可靠;全固态电容，稳定可靠；工业级电路设计6工业级TVS防护600W；电源输入防雷防浪涌。

7宽电压输入DC36-DC6V，自动防反接。

8支持热拔插，换SD卡无需重启模块。

9超高速并行处理算法，使得每秒处理的数据包增大到10个以上。

10内部高精度RTC和可充电纽扣电池，自动充电。

掉电时间不丢失，设备时钟可以不加电状态下稳定工作1年以上。

11全系列串口（RS232,RS485,RS422），智能切换技术，无须跳线或设置。

12主动数据采集命令，命令时间和数据都可以自由设置。

13定时新建文件，时间可设。

14可选自动给数据添加时间戳。

15双接收通道采集数据，可以同时监控设备通信收、发的所有数据。

型号功能列表：3使用方法设备通过串口进行通信，其功能定义如下所示。

对于同时具有RS422、RS485和RS232接口的记录仪产品，不能同时使用多个接口，否则会造成工作不正常。

一次只能选择使用任意一个接口。

Pin1P in10R S48512345678910T x+T x-R x+R x-G T X R X R x2P-P+R S422R S232D C6~32V 正确连接设备串口与主机串口（计算机）供电。

待设备启动后，会从串口发出“OK！明设备初始化完成，并成功启动。

如果设备缺少其中，“设备时间”为读取记录仪内部时钟时间。

“对设备校时”为将本计算机的时间设置到数据记录仪中。

测试程序只提供了读写文件0#操作，用户可以参考协议详解进行其他操作。

“数据直接保存”为设置是否启用直接存储功能，即自动建立文件，并且保存串口收到的数据（不满足通信协议规范的）到默认文件。

“定时新建文件”设置间隔多少时间建立一个文件，例如60为设置1个小时建立一个文件，设置为1440则为每天建立一个文件。

设置为0，则表示不在运行过程中建立文件，只有上电的时候才会建立一次文件。

“数据间隔”设置串口数据的分割时间，一般采用默认即可。

小于10ms 的设置无效。

设备会自动按最低的间隔来处理。

“数据时间戳”可以设置是否自动给数据添加时间标示。

添加的时间格式为[HH:MM:SS]。

修改记录仪串口参数以后，需要断电重新启动记录仪，新的设置才会有效。

使用双通道采集，数据侦测的方法：图中，Rx2为扩展接收数据通道，在需要同时采集两个通道的接收数据时采用。

使用时，如下图接线。

其中RX 接收的数据存储以接收的数据存储以““Rx Rx””标示标示，，RX2RX2接收到的接收到的数据以数据以““Tx Tx””标示（RX2连接发送数据线，表示发送线中的数据）。

4技术参数产品名称：串口转SD卡数据记录仪数据通信：RS422，RS485，RS232全兼容带隔离数据格式：2400-115200格式可设（默认：9600，8-N-1）文件名称：MMDDHHMM.txt(MM月份，DD日期，HH小时MM分钟）电源：DC6-32V防反接功耗：最大0.5W重量：180克体积：长：102mm，宽：70mm，高：22mmSD卡标准：支持SD和SDHC，容量最大支持32G文件格式：默认*.txt，可建立任意文件格式防护技术：3kV隔离，1500W防雷放浪涌内置时钟：内置独立RTC（提供串口校时功能）5协议详解设备串口发送数据包到存储模块，存储模块解析数据包内容后，作相应的处理，然后将结果发送回串口。

通信过程采用一发一答的方式，即设备主动发送数据到存储模块，存储模块才会发回应答。

发送命令和应答均遵循以下规范。

通信格式：起始字节+字节数+功能码+参数+累加校验+结束符'S'+Num+CODE+Data+FA+'E'0--------1------2------3-----buf[1]+2-----buf[1]+3Num:1byte，表示code+data总字节数，最大250CODE:1byte，表示功能码，由功能代码和文件句柄索引2个信息组成。

FA:1byte，累加校验计算方法为：'S'+Num+CODE+Data（下传命令可以不校验）功能码字节：|7|6|5|4|3|2|1|0|bit7~bit2功能码，bit1~bit0文件索引。

例如：打开文件的功能码为：0X10那么打开文件句柄0功能码为：0X10|0X00=0X10那么打开文件句柄1功能码为：0X10|0X01=0X11那么打开文件句柄2功能码为：0X10|0X02=0X12注意：1，最多支持3个文件句柄同时操作，即同时打开了3个文件读写。

文件句柄2默认为串口直接存储数据的文件，因此，如果需要使用串口数据直接保存，请勿操作文件句柄2。

2，如果需要读写的文件超过3个，可以使用同一个文件句柄，打开一个文件读写后，关闭该文件；然后，再打开下一个文件操作。

【1,设置打开文件方式】功能码:0X00|FileIndex发送到模块串口：'S'+Num+'0X00|FileIndex'+"filemode"+FA+'E'从模块返回：操作成功：'S'+Num+'0X00'+'1'+FA+'E'操作失败：'S'+Num+'0X00'+'0'+FA+'E'注意："filemode"设置如下："filemode"可读可写追加方式创建二进制"r"10000 "w"01010 "a"01110 "rb"10001 "wb"01011 "ab"01111"r+"11000"w+"11010"a+"11110"r+b"或"rb+"11001"w+b"或"wb+"11011"a+b"或"ab+"11111注意：一般写文件采用追加，而读文件不能以追加方式。

所以读操作前，需要重新按读的方式打开文件，并且使文件的指针位于文件的最开始，每次读操作后，文件指针会后移。

【2,打开文件】功能码:0X10|FileIndex发送到记录仪串口：'S'+Num+'0X10|FileIndex'+"filename"+FA+'E'从记录仪返回：操作成功：'S'+Num+'0X10'+'1'+FA+'E'操作失败：'S'+Num+'0X10'+'0'+FA+'E'注意：filename:8.3format采用8.3文件命名方式。

即文件名8个字节，后缀3个字节。

【3,写文件】功能码:0X20|FileIndex发送到记录仪串口：'S'+Num+'0X20|FileIndex'+"filedata"+FA+'E'从记录仪返回：操作成功：'S'+Num+'0X20'+'1'+FA+'E'操作失败：'S'+Num+'0X20'+'0'+FA+'E'注意：一次操作最多文件数据为250字节.【4,读文件】功能码:0X30|FileIndex发送到记录仪串口：'S'+Num+'0X30|FileIndex'+ReadDataNum+FA+'E'从记录仪返回：操作成功：'S'+Num+'0X30'+'1'+"DATA"+FA+'E'操作失败：'S'+Num+'0X30'+'0'+FA+'E'注意：ReadDataNum为一个字节长度。