电梯专业英语词典全集

电梯专业英语词典全集A1abbreviation 缩语abnormal 不正常的,反常的abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC(alternating current) 交流电AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速2AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC-GL machine 交流无齿曳引机acceleration(accel)rate 加速器acceleration control system 加速度控制系统accelerator 加速器acceptanec certificate 验收证书acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验access forbidden 禁止入access door 检修门access lift 通道电梯3access security 通道防卫access switch 通道开关,维修用开关access way 进出通道accessibility 可通达性,接近的,难易程度accessible 允许进入accessible space 允许进入的场地accessory 配件,附件accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积4accumulator 蓄电池acoustic 听觉的,声音的activate 启动,触发active mode 主动模式actual condition 实际状况,实际条件actual load 实际载荷actual state 实际状况actual value 实际值actuate 开动,操作,激励actuating magnet 操作磁铁actuating linkege 操作连杆actuation time 动作时间actuator 操纵机构,激励器,螺线管actuator bracket 调节器支架actuator plate 调节板ACVF(AC varible frequency) 交流调速5ACVF drive 交流调频拖动ACVF system 交流调频系统ACVV(AC varible voltage) 交流调压ACVV dirve 交流调压拖动ACVV system 交流调压系统adaptation 适应,匹配adapter(adapator) 适配器adapter PCB 选通脉冲印刷电路板adapting 选配adaptive control system 自适应能力控制系统addendum 齿顶高,附录addendum circle 外圆adding working drawing 附加加工图addition 附加物,加法additional materials 附加材料address 地址6adhesion 胶,粘合胶adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car 相邻轿厢,相邻电梯adjacent entrance 相邻出入口adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动adjustable wrench 活动扳手,可调扳手adjusting screw 调节螺丝adjusment 调试adjustor 调试员7 administration cost 管理成本administration expenses 管理费用administation overjhead rate 管理费用标准advance door opening 提前开门advance payment 预付款advanced 提前的,先进的advanced carriage 超前拖板(选层器) advancing position reference value 超前位置参考值aerial cableway 空中缆车,架空索道aerial ropeway 空中缆车,架空索道aerial tramway 空中缆车,架空索道aesthetic 美观after sales service 售后服务agency 代理8agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器air-condition 空调air-gap 气隙airborne noise 空气传播噪声alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统alcove arrangement 电梯U型排列法ALC(autoclaved light-weight concrete) 蒸压轻质混凝土9algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation 分配,分派allocation of landing call 层站呼梯指令分配allowble stress for temporary load 允许暂时应力值allowance 允用误差,加工余量alloy 合金alloy steel 合金钢10alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大11 amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analogue(analog) 模拟analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage 锚具,锚定angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架12angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检13annual report 年度报告annunciator 报音器,声音合成器anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置14anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparent output 视在输出apparen power 视在功率applicant 申请人application 申请application guide 应用指南aprons 裙板arbour 轴,杆arc chamber 电弧隔离室15arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm 臂,支路armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组16armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路17assemble 装配assembler language 汇编语言ssembly drawing 组装图assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号sudible signaling system 音响信号系统audio tape recording 磁带录音authority 当局,核准部门18authority of lift acceptance 电梯验收部门authorized 授权的,核准的authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层19automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门20automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助驱动auxiliary value 辅助材料auxiliary materials 辅助量auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间21average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴Bbabbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器22babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯) back side 后侧,后边back wall 后壁back type governor 轴流式限速器baked enamel 烤漆balance 平衡balance chain 平衡链balance coefficient 平衡系数balace weight 平衡器balanced traffic 平衡交通23ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade panel 扶手板balustrade skirting 扶手群板balustrade lighting 扶手照明balustrades 扶手装置bandsaw 带锯bank 银行,群组,排bar 条,棒bar code 条形码bar lock 杆式锁24bare wire 裸线barricade 防护墙,隔墙barrier 隔板,栅栏base 基座,基础base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery box 蓄电池箱battery charger 电池充电器battery- backed 电池支持的baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制25beam 梁beam pad 井道电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动26belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bi-parting 对开式(上下开启) bi-parting door 垂直中分门bias 偏置,偏移bid 投标,报价bid table 报价单bidder 投标27bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bill of expenses 费用帐单bil of lading 海运提单bill of materials 材料单billing 开发票binary 二进制binder 装订册bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade 叶片,刀片,锯片blade connector 刀形连接器28bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boarding 登梯boading floor 登梯楼层boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站29boading time 登梯时间boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole 钻孔,镗孔boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程30bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box 盒,箱box counterweight 箱式对重Braille 盲文字符31brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press 折弯机,压弯机brake pulley 制动轮brake release lever 制动器松闸手柄32brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break 切断,破断break-down 故障breaking load 破断负荷33breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置34broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching 成组,成群brush finished stainless steel 哑光不锈钢35brush holder 刷握,滑环brush yoke 刷架budget 预算buffer 缓冲器buffer stroke 缓冲器冲程buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer support 缓冲器支承buffer switch 缓冲器开关builder 建筑单位nbuilder's work 土建工程36buider's work drawing 土建图纸building 建筑building area 建筑面积building contractor 建筑承包商buiding facility 大楼设施building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口buiding supervision center 大楼监管中心built=in 装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行37buried 埋入的burn in (程序)灌入burr 毛刺,毛边burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing 衬套,轴套,套筒butt joint 平接,对焊button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶38by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站CC$F 到岸价cab 轿厢,座舱cab interior 轿厢部cabin 轿厢,座舱cabinet 柜,厢cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入39cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call 呼梯,呼叫call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派40cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel 撤消,取消cancelingof call signal 呼梯信号消除cancellation 撤消,取消canopy 顶盖,大蓬canvas 帆布canvas hose 帆布软管cap 帽,盖子cap nut 螺母capacitance 电容,电容量capacitor 电容capacitor motor 电容器电机capacity 载重,容量,定员capacity plate 载量标牌41capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment 轿厢调度,轿厢分配car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层42call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call contrl 呼梯指令控制call conmting system 呼梯计数系统call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call tegistration 呼梯登陆43call registration indicator 呼梯登陆信号call sequence 呼梯顺序call-back 召修call-back message 召修信息call-out response time 维修召唤应答时间call-out service 急修服务callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴44car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶45car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨46car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit 轿厢安全门,应急门car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior 轿厢外装修,轿厢外表car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame 轿厢架,轿架car frame 轿厢架,轿架47car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control 手柄开关操纵,轿开关控制car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明48car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel 轿厢照明板,照明天花板car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座49car panel with window 轿厢壁板上窗口cr parking device 轿厢驻停装置car platform 轿厢底,轿底car platform guard 轿厢站台护板car platform sill 轿厢car position indicator 轿厢指示灯,轿厢位置显示car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof 轿厢顶,轿顶car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯)50car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling 轿厢架,吊架car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置51car switch control 轿厢开关控制car switch opration 手柄开关操纵,轿开关控制car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit 轿顶安全出口,轿顶应急出口car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆52car ventilation 轿厢通风car walls 轿厢壁,轿壁car weight 轿厢重量car width 轿厢宽度carbon 碳,石墨carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card 卡片,纹板card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费53carry frequency 载波频率,开关工作频率carrying capacity 载运量,载运能力cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade 级联,串联cascade sub-loop 串接式子回路case 箱,盒,外壳casing 保护套,外套casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油54catch 擎子,门扣,捕捉器catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation 气穴,涡穴,饱和压力点ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement 水泥,胶合剂cement concrete 混凝土center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心55center opening 中分式门center opening door 中分门center-opening folding door 中分式折叠门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support 中心支撑,中间支撑,第三支撑centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置56central position 中心位置centrifugal 离心的cenrifugal brake 离心制动器centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架57chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link 链节,链环chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链紧装置chain wheel 链轮chain wheel track 链轮导轨chamger 倒棱,去毛刺change switch 转换开关58change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character 特征,字符characteristic 特征,特性characteristic curve 特性曲线charge 充电,收费charged 带电,充电charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀59chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke 扼流,截流,阻塞choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle 周期,圆circuit 电路circuit breaker 断电器,断路器60circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring 压制环,加紧环clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度61clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clerance 间隙clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clevis U型夹client 客户,买主62clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管63clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体) CNC(computerized numric control) 计算机数控coaxial cable 同轴电缆coast to stop 滑行停车coating 涂层cock 龙头code 码,符号,规程,规code of practice 实施规程,实用规程code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数64coil 线圈,绕组coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate 栅栏门,折叠式门collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection 收集,集合collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯65collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column 柱,立柱comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置68 commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment 隔板,隔室compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compennsating device for hoist ropes 曳引绳补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置69compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensanting/equalizer disk 补偿/补偿器compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent 有资格的,胜任的70competent personnel 有资格的人员,胜任的人员competitor system 竞争机制component 部件compound wound 复绕compound wind motor 复励电动机comprehensive 综合的comprehensive maintenance contract 综合维修合同,全包维修合同comprehensive service contract 综合维修合同,全包维修合同compressing spring 压缩弹簧compression 压缩compressive stress 压应力compression switch 压缩开关compressor 压缩器71compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed 隐蔽的,暗式concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容72condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod 连杆,连接杆73connection 连接connection diagram of controller 控制柜连线图connector 接线柱,连接器consecutively departing 依次派出的轿厢console panel 控制柜,控制盘constant 恒定的,常数constant HP motor 功率恒定型电机constant speed valve 比例控制阀,调速阀constant torque motor 力矩恒定型电机construction 安装,施工construction crane 建筑起重机construction layout drawing 土建图construction platform 安装平台,施工平台74construction site 安装工地,施工工地consultant 顾问,咨询机构consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger 接触指,滑触头contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷75contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 容continuing travel indicator (轿)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract 合同,契约,承包合同76contract capacity 合同载重量,合同容量contract load 合同负载contract of indemnity 赔偿合同contract party 合同方,合同当事人conract specification 合同规定,合同明细表conract speed 合同速度,额定速度contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置77control feature 控制特征control guard for handrail breakage 扶手带断带保护装置control gear 控制论control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage 控制电压,操作电压78controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conventional 常规的conventional lift 普通电梯converter 整流器,转换头converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机79conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord 绳索,芯线cord drive 绳传动,(厅门) core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner 角,隔80corner post 对角立柱corpus lift 尸体升降机correct phase sequence 正确相序correcting 修正,校正correcting travel 校准运行correction 校正,校准corrective maintenance 校正维修corridor 走廊corrosion proof 防腐蚀的corrosion resistant 耐腐蚀的corrosion resistant coating 涂防锈漆层corrosive 腐蚀的cost 成本,费用cost accounting 成倍核算cost analysis 成本分析cost calculation 成倍计算cost comparison 成本比较81cost effective 价格划算的cost element 成本项目cost estimate 成本估算cost of material 材料成本cost of production 生产成本cost price 成本价cost share 成本份额cost situation 成本状况cost structure 成本结构cost-free 免费的cotter pin 开口销conter 计数器counter emf 反电动势counter inductor 记数感应器counter sunk head 埋头conuter-clockwise 逆时针方向counterbalance 相互平衡,配重平衡82countersink 沉头,埋入counterweight 对重装置,对重counterweight bottom runby 对重底部越程counterweight filler 对重块,对重装置重鉈counterweight filler weight 对重块,对重装置重鉈counterweight frame 对重框counterweight guard 对重防护栏counterweight header 对重头counterweight housing 对重架counterweight safety 对重安全钳counterweight sheave 对重绳轮counterweight sling 对重吊具countreweight suspension 对重悬挂装置83counterweight top clearance 对重装置顶部安全装置couple M to N 使M和N偶合coupled door panels 配对门扇counpler 联轴器coupling 联轴器coupling bolt 联轴器螺栓coupling sleeve 联接套筒cove 凹口cover 盖,保护层cover plate 盖板cover strip 覆盖条covered wire 覆层线CPS( central processing system) 中央处理系统CPU(central processing unit) 计算机中央处理器84crack 裂缝crack-resistant 抗裂的cracking pressure 破裂压力cradle beam 托架,横梁crank 曲轴crank operation 曲轴操作crank shaft 曲轴crank shaft oil seal 曲轴油封creep 爬行,蠕动creep speed 爬行速度,平层速度creeping-in distance 爬行距离Cremona's method 谷式应力图crest value 峰值crimp-meshed door 铁网门critical path planning 关键路线计划法85cross beam 顶梁,上梁cross head screwdriver 十字头螺丝功锥cross pin 十字销cross valve 三通阀cross-head 上梁cross-head screw 十字头螺钉cross-section 横截面crosshead sheave 轿顶轮crow bar 撬棒crown bar 顶杆crown wheel 盘形轮crushing 压碎,压溃cup 杯,盖子cup head square neck bolt 半圆头方颈螺栓current 电流current carrying 带电的86current carrying capacity 载流量current characteristic 电流参数current control loop 电流控制回路current efficiency 电流效率。