3535RGB产品规格书

合集下载

3535说明书

德国“天马”3535中文手册重要注意事项●为确保本机不会泄漏对人体有害的紫外光，必需使用天马原厂的滤光玻璃。

●为确保本机操作时所产生的臭氧浓度达至安全水平，本机灯管必需使用天马原厂灯管。

操作面板A、B为全光4KWC为半光2KW晒版机电脑的操作输入曝光程序当需要输入或更改曝光程序时，抽气架的手柄必需保持在松开状态。

每一级光源都有24组曝光程序记忆，所以三级光源共有72组曝光程序记忆。

曝光程序的输入方法如下：●选择光源强度。

●按PROG键。

PROG显示上的小数点会亮着，输入需要输入或更改曝光程序号码（1-24）。

●按PROG键，电脑会显示出所选择的程序内的资料于V ACI、V ACII、EXPI及EXPII的数字显示上。

如需要更改资料，请按下需要更改的项目按键（显示上的小数点会亮着），然后输入需要的时间。

如需更改其他项目，可选择其他项目按键或按PROG键储存已输入的资料。

开始和停止曝光程序当手柄扣上后，抽气泵便会立即启动。

电脑上的抽气时间便开始递减。

按电脑上的停止键（STOP），曝光程序便会停止。

测试灯管光亮度这个测试是以全光进行的。

并松开抽气架手柄。

1.选择使用全光程序。

2.同时按下1及3键。

注意：此时快门会打开，请避免眼睛被强光照射。

3. 主曝光时间显示会显示出灯管亮度的百分比，如数字显示小于70，在扩散曝光时间显示会显示出灯管型号，操作员可自行决定是否需要更换灯管。

注意：灯管因长期在高温环境下工作，灯管可能因受热而变形。

灯管如使用了半年或以上，操作员应在下班前检查灯管形状，检查程序如下：a)同时按下1及3键启动测试灯管光亮度程序。

b)当快门开启后将电源关闭。

c)观察灯管有没有变形。

如有，请更换灯管。

（如使用已变形的灯管，灯管可能因过热而爆炸，导致操作人员受伤。

）显示电脑软件版本及灯管使用时间当在测试灯管光亮度程序进行中同时按下1及3键，电脑便会进入显示软件版本及灯管使用时间模式，数字显示内容如下：更换灯管后，重臵灯管已使用时间的方法如下：在显示软件版本及灯管使用时间模式下，同时按下4及6键，灯管已使用时间便会重臵为0，而更换灯管次数显示便会增加1次。

台湾葳天UV3535光源规格书

No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, ProLight PK2N-3LLE-SD 3W UV Power LED Technical Datasheet Version: 1.5Features‧100% foot print compatible with Cree XP-C / XP-E / XP-G‧Best thermal material solution of the world ‧Best Moisture Sensitivity:JEDEC Level 1 ‧RoHS compliantIntroduction‧ProLight Phenix 3535, is one of the smallest high power LED footprintavailable by ProLight Opto, has offered extended solid-state lighting design possibilities.ProLight Phenix 3535 is designed with ProLight own Patents and using copper leadframe, the best thermal material of the world.‧Phenix 3535 qualifies as the JEDEC Level 1 MSL sensitivity level and suitable for SMD process, Pb_free reflow soldering capability, and full compliance with EU Reduction of Hazardous Substances (RoHS) legislation.2014/04 Main Applications‧UV gluing, UV curing, UV marking‧UV drying of printing inks and lacquers ‧Currency inspection‧Forensic analysis - urine, protein stains ‧Leak detection using fluorescent dyes ‧Detects fluorescing minerals and gems ‧Indoor Lighting ‧Outdoor LightingEmitter Mechanical DimensionsNotes:1. The cathode side of the device is denoted by the chamfer on the part body.2. Electrical insulation between the case and the board is required. Do not electrically connecteither the anode or cathode to the slug.3. Drawing not to scale.4. All dimensions are in millimeters.5. Unless otherwise indicated, tolerances are ± 0.10mm.6. Please do not solder the emitter by manual hand soldering, otherwise it will damage the emitter.7. Please do not use a force of over 0.3kgf impact or pressure on the lens of the LED, otherwiseit will cause a catastrophic failure.*The appearance and specifications of the product may be modified for improvement without notice.2No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 3Flux Characteristics, T J = 25°CRadiation Pattern ColorPart Number EmitterRadiometric Power (mW) @350mA Refer @700mAMinimum Typical Minimum TypicalLambertianUVPK2N-3LLE-SD335 510650950●ProLight maintains a tolerance of ± 10% on flux and power measurements.● Please do not drive at rated current more than 1 second without proper heat sink.Thermal Forward Voltage V F (V)Forward Voltage V F (V)Resistance @ 350mARefer @700mAJunction to ColorMin. Typ. Max.Typ.Slug (°C/ W)UV2.853.23.85 3.68●ProLight maintains a tolerance of ± 0.1V for Voltage measurements.Electrical Characteristics, T J = 25°COptical Characteristics at 350mA, T J = 25°CTotal included Viewing Angle Angle Radiation ColorPeak Wavelength λP(degrees) (degrees) PatternMin.Typ.Max.θ0.90V2 θ1/2 LambertianUV390 nm400 nm410 nm160130●ProLight maintains a tolerance of ± 1nm for dominant wavelength measurements.No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, Absolute Maximum RatingsParameterUVDC Forward Current (mA)700Peak Pulsed Forward Current (mA) 1000 (less than 1/10 duty cycle@1KHz)Average Forward Current (mA) 700ESD Sensitivity±4000V (Class III)(HBM per MIL-STD-883E Method 3015.7) LED Junction Temperature 120°C Operating Board Temperature -40°C - 90°Cat Maximum DC Forward Current Storage Temperature -40°C - 120°C Soldering Temperature JEDEC 020c 260°CAllowable Reflow Cycles 3Reverse VoltageNot designed to be driven in reverse bias4ColorBin CodeMinimum MaximumAvailable Radiometric Power (mW) Radiometric Power (mW)Color BinsUVP 335 435 【1】Q 435 515 2, 3, 4 【1】R 515 635 2, 3, 4 【1】S 635 755【1】●ProLight maintains a tolerance of ± 10% on flux and power measurements. ● The flux bin of the product may be modified for improvement without notice.● 【1】The rest of color bins are not 100% ready for order currently. Please ask for quote and order possibility.Radiometric Power Bin Structure at 350mANo. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, ColorBin CodeMinimum Peak Maximum Peak Wavelength (nm)Wavelength (nm)UV1 390 3952 395 4003 400 4054 405 410●ProLight maintains a tolerance of ± 1nm for peak wavelength measurements.Peak Wavelength Bin Structure5Forward Voltage Bin StructureColorBin CodeMinimum Voltage (V)Maximum Voltage (V)UVA 2.85 3.10B 3.10 3.35 D 3.35 3.60 E3.603.85●ProLight maintains a tolerance of ± 0.1V for Voltage measurements.Note: Although several bins are outlined, product availability in a particular bin varies by production run and by product performance. Not all bins are available in all colors.No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 1. UV6Color Spectrum, T J = 25°C0.00.2 0.4 0.6 0.8 1.0 350400 450 500 550 600 650 700 750 800R e l a t i v e S p e c t r a l P o w e r D i s t r i b u t i o nWavelength (nm)Light Output CharacteristicsRelative Light Output vs. Junction Temperature at 700mA0 20 40 60 80 100 120 140 160 020406080100120R e l a t i v e L i g h t O u t p u t (%)Junction Temperature, T J (℃)UVNo. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 0 100 200 300 400 500 600 700 800 0255075100125150F o r w a r d C u r r e n t (m A )Ambient Temperature (℃)R θJ-A = 30°C/W R θJ-A = 25°C/W R θJ-A = 15°C/WR θJ-A = 20°C/W 0.00.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0200400600800R e l a t i v e L u m i n o u s F l u xForward Current (mA) 0100 200 300 400 500 600 700 800 0 0.5 1 1.5 2 2.5 3 3.5 4A v e r a g e F o r w a r d C u r r e n t (m A )Forward Voltage (V)Forward Current Characteristics, T J = 25°CFig 1. Forward Current vs. Forward Voltage for UV.Fig 2. Relative Luminous Flux vs. Forward Current for UV at T J =25 maintained.7Ambient Temperature vs. Maximum Forward Current1. UV (T JMAX = 120°C)No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 8Typical Representative Spatial Radiation PatternLambertian Radiation Pattern0 10 20 30 40 50 60 70 80 90 100 -100-80-60-40 -20 0 20 406080100R e l a t i v e I n t e n s i t y (%)Angular Displacement (Degrees)Soak RequirementsLevel Floor Life Standard Accelerated Environment Time Conditions Time (hours) Conditions Time (hours) Conditions1 Unlimited ≤30°C /168 +5/-085°C /NA NA 85% RH 85% RH●The standard soak time includes a default value of 24 hours for semiconductor manufature'sexposure time (MET) between bake and bag and includes the maximum time allowed out ofthe bag at the distributor's facility.●Table below presents the moisture sensitivity level definitions per IPC/JEDEC's J-STD-020C.Soak Requirements Level Floor Life Standard Accelerated Environment Time Conditions Time (hours) Conditions Time (hours) Conditions1 Unlimited ≤30°C /168 +5/-085°C /NA NA 85% RH 85% RH2 1 year ≤30°C /168 +5/-085°C /NA NA 60% RH 60% RH2a 4 weeks ≤30°C /696 +5/-030°C /120 +1/-060°C / 60% RH 60% RH 60% RH3 168 hours ≤30°C /192 +5/-030°C /40 +1/-060°C / 60% RH 60% RH 60% RH4 72 hours ≤30°C /96 +2/-030°C /20 +0.5/-060°C / 60% RH 60% RH 60% RH5 48 hours ≤30°C /72 +2/-030°C /15 +0.5/-060°C / 60% RH 60% RH 60% RH5a 24 hours ≤30°C /48 +2/-030°C /10 +0.5/-060°C / 60% RH 60% RH 60% RH6 Time on Label ≤30°C / Time on Label 30°C /NA NA (TOL) 60% RH (TOL) 60% RHMoisture Sensitivity Level - JEDEC Level 1No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,9No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,Stress TestStress ConditionsStress Duration Failure Criteria Room Temperature25°C, I F = max DC (Note 1)1000 hoursNote 2Operating Life (RTOL)Wet High Temperature85°C/60%RH, I F = max DC (Note 1)1000 hoursNote 2Operating Life (WHTOL)Wet High Temperature85°C/85%RH, non-operating1000 hoursNote 2Storage Life (WHTSL)High Temperature110°C, non-operating1000 hoursNote 2Storage Life (HTSL)Low Temperature-40°C, non-operating1000 hoursNote 2Storage Life (LTSL)Non-operating -40°C to 120°C, 30 min. dwell,200 cyclesNote 2Temperature Cycle (TMCL) <5 min. transferNon-operating -40°C to 120°C, 20 min. dwell,200 cyclesNote 2Thermal Shock (TMSK) <20 sec. transferMechanical Shock1500 G, 0.5 msec. pulse,Note 35 shocks each6 axis Natural Drop On concrete from 1.2 m, 3XNote 3Variable Vibration10-2000-10 Hz, log or linear sweep rate,Note 3Frequency20 G about 1 min., 1.5 mm, 3X/axis Solder Heat Resistance260°C ± 5°C, 10 sec.Note 3(SHR)SolderabilitySteam age for 16 hrs., then solder dipSolder coverage at 260°C for 5 sec.on leadNotes:1. Depending on the maximum derating curve.2. Criteria for judging failureItemTest Condition Criteria for Judgement Min. Max. Forward Voltage (V F ) I F = max DC -- Initial Level x 1.1 Luminous Flux or I F = max DCInitial Level x 0.7--Radiometric Power (ΦV )* The test is performed after the LED is cooled down to the room temperature. 3. A failure is an LED that is open or shorted.10Qualification Reliability TestingNo. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, TYPE A.11Recommended Solder Pad DesignStandard Emitter ●All dimensions are in millimeters.● Electrical isolation is required between Slug and Solder Pad.TYPE B.No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 12Reflow Soldering ConditionProfile Feature Sn-Pb Eutectic AssemblyPb-Free Assembly Average Ramp-Up Rate3°C / second max.3°C / second max.(T Smax to T P ) Preheat– Temperature Min (T Smin ) 100°C 150°C – Temperature Max (T Smax ) 150°C 200°C – Time (t Smin to t Smax ) 60-120 seconds 60-180 seconds Time maintained above:– Temperature (T L ) 183°C 217°C – Time (t L ) 60-150 seconds 60-150 secondsPeak/Classification Temperature (T P ) 240°C 260°C Time Within 5°C of Actual Peak10-30 seconds20-40 seconds Temperature (t P ) Ramp-Down Rate 6°C/second max. 6°C/second max. Time 25°C to Peak Temperature 6 minutes max.8 minutes max.● We recommend using the M705-S101-S4 solder paste from SMIC (Senju Metal Industry Co., Ltd.) for lead-free soldering.● Do not use solder pastes with post reflow flux residue>47%. (58Bi-42Sn eutectic alloy, etc) This kind of solder pastes may cause a reliability problem to LED.● All temperatures refer to topside of the package, measured on the package body surface.● Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. ● Reflow soldering should not be done more than three times. ● When soldering, do not put stress on the LEDs during heating. ● After soldering, do not warp the circuit board.t 25°C to Peakt S PreheatTimeT e m p e r a t u r eCritical Zone T L to T PRamp-upRamp-downT SmaxT Smint Pt LT PT L25IPC-020cNotes:1. Drawing not to scale.2. All dimensions are in millimeters.3. Unless otherwise indicated, tolerances are ± 0.10mm.13 No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 14Notes:1. Empty component pockets sealed with top cover tape.2. 250, 500 and 1000 pieces per reel.3. Drawing not to scale.4. All dimensions are in millimeters.178 ± 13 ± 0.54 ± 0.5 5 ± 0.560 ± 0.513.2 ± 0.516.2 ± 0.5Φ 13.1 ± 0.5Φ 21 ± 0.5No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 15Precaution for UseHandling of Silicone Lens LEDsNotes for handling of silicone lens LEDs● Please do not use a force of over 0.3kgf impact or pressure on the silicone lens, otherwise it will cause a catastrophic failure.● The LEDs should only be picked up by making contact with the sides of the LED body. ● Avoid touching the silicone lens especially by sharp tools such as Tweezers. ● Avoid leaving fingerprints on the silicone lens.● Please store the LEDs away from dusty areas or seal the product against dust. ● When populating boards in SMT production, there are basically no restrictions regarding the form of the pick and place nozzle, except that mechanical pressure on the silicone lens must be prevented.● Please do not mold over the silicone lens with another resin. (epoxy, urethane, etc)●StoragePlease do not open the moisture barrier bag (MBB) more than one week. This may cause the leads of LED discoloration. We recommend storing ProLight’s LEDs in a dry box after opening the MBB. The recommended storage conditions are temperature 5 to 30°C and humidity less than 40% RH. It is also recommended to return the LEDs to the MBB and to reseal the MBB. ● The slug is is not electrically neutral. Therefore, we recommend to isolate the heat sink.● We recommend using the M705-S101-S4 solder paste from SMIC (Senju Metal Industry Co., Ltd.) for lead-free soldering.● Do not use solder pastes with post reflow flux residue>47%. (58Bi-42Sn eutectic alloy, etc) This kind of solder pastes may cause a reliability problem to LED.● Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temperature after soldering. ● Please avoid rapid cooling after soldering.● Components should not be mounted on warped direction of PCB.● Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a heat plate should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.● This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When cleaning is required, isopropyl alcohol should be used.● When the LEDs are illuminating, operating current should be decide after considering the package maximum temperature.● The appearance, specifications and flux bin of the product may be modified for improvement without notice. Please refer to the below website for the latest datasheets. /。

3535RGB全彩led规格书

Features :*Low power consumption *Small efficiency.V ersatile mounting on p.c board Unit :mmdimensions are in millimeters (inches).Tolerance is ±0.25mm (.010”)unless otherwise Specifications are subject to change without2(+)G 3(+)R 1(+)B 5(-)4(-)6(-)5(-)4(-)6(-)2(+)G3(+)R1(+)BAbsolute Maximum Ratings at Ta=25℃Parameter Rating UnitPower Dissipation(Pd)70mW Peak Forward Current(1/10Duty Cycle0.1mspulse Width100mAForward Current(IF)20mAReverse V oltage(VR)5V Operating Temperature Range-20℃~+80℃Storage Temperature Range-30℃~+100℃Lead Soldering Temperature210℃for5SecondsSelection Guide`Parameter Min Tvo Max Unit Test ConditionLuminous Intensity(IV)Red750----Mcd If=20mA Green1600——Mcd If=20mA Blue350450Mcd If=20mAThe wavelengthRed620----630nm If=20mA Green517——530nm If=20mA Blue460——475nm If=20mAForward V oltage(VF)Red 1.8---- 2.4V If=20mA Green 3.0---- 3.4V If=20mA Blue 3.0 3.4V If=20mAReverse Current(IR)----5µA Vr=5V Selection Guide：Lens color ChipWater clearMaterial Emittedcolorλp(nm) InGaN/GaNRed620Green525Blue472１９００900Typical Electrical/Optical Characteristics Curves (R):：Typical Electrical/Optical Characteristics Curves (G):LabeP/N:The product model IV:Luminous intensity rank VF:Forward voltage rank TC:Color temperature Q`T:numberQC:Production orderMoisture Resistant PackagingNote:unless mentioned,tolerance of +/-0.1mm,unit:LableAluminum moisture-proof bagDesiccantSMDThe produc ts take note1；Graph one ：Hands material taking ：1.Hand have sweat ，Sweat on silicon surface existing optical pollution ，Influence luminous 。

PQ3535磁芯与骨架规格书

35.5 max 31.4
.6 (2x)
39.1 35.5
35.5
Dimensions in mm.
9.6 19.8
30
∅ 14.7
5.3 min
Fig.2 PQ35/35 coil former; 12-pins.
5.1 (8x)
MFP180
Winding data for 12-pins PQ35/35 coil former
3C81
3C90
3C91 3C94 3C95 3C96
315 ±3% 400 ±3% 630 ±3% 1000 ±3% 1600 ±5% 6000 ±25% 315 ±3% 400 ±3% 630 ±3% 1000 ±3% 1600 ±5% 5200 ±25% 6000 ±25% 5200 ±25% 6000 ±25% 4700 ±25%
≈0 ≈0 ≈0 ≈0 ≈0
TYPE NUMBER
PQ35/35-3C81-E315 PQ35/35-3C81-E400 PQ35/35-3C81-A630 PQ35/35-3C81-A1000 PQ35/35-3C81-A1600 PQ35/35-3C81 PQ35/35-3C90-E315 PQ35/35-3C90-E400 PQ35/35-3C90-A630 PQ35/35-3C90-A1000 PQ35/35-3C90-A1600 PQ35/35-3C90 PQ35/35-3C91 PQ35/35-3C94 PQ35/35-3C95 PQ35/35-3C96
These products are recommended for use in current designs and are available via our sales channels. These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability.

3535RGB规格书

承认书客户名称Client appellation:产品型号Model NO.: 3535RGB（晶元全彩）产品规格Specification: 3535 Top View LEDs样品编号NO.:、■特征:●宽角度全彩LED●支架有6个PIN脚●具有宽的发光角度●上锡方式:回流焊●抗静电●无铅●符合ROHS■描述 :●3535产品拥有宽的发光角度及高光效，该全彩产品采用蓝色、红色、绿色波长芯片加特殊工艺制作而成■用途:●背光●灯条●模组■外观描述:■封装尺寸1. 所有标注尺寸的单位均为毫米2. 除了特别注明,所有标注尺寸的公差均为±0.10mm█绝对最大额定值(Ta = 25℃)参数符号值单位正向电流IF 90 mA 峰值正向电流(Duty 1/10 @1KHz) IFP 100mA 功耗Pd 330 mW 操作温度Topr -40 to +85 ℃保存温度Tstg -40 to +90 ℃静电防护ESD 2000 V 回流焊最高温度Tsol 260±5 ℃反向电压VR 5 V 注明: *1:回流焊时间≦ 5 秒.█电性与光学特性(Ta=25℃)█信赖性测试项目与条件: 产品的可靠性应满足于下列项目：信任级别：90％Notes:Ivt: 信赖性测试前Iv值；Iv: 完成信赖性测试后Iv值；U：规格上限值L：规格下限值■使用说明1. 过电流保护客户必须使用电阻来保护，否则电压的漂移会引起电流的大幅度改变(发生击穿现象).灯珠使用时电流必须在规定范围之内，避免电流过大造成不良。

2. 储存2-1. 准备使用产品前不要打开防潮袋。

开封前请先检查包装袋有无漏气,开包后检查湿度标示卡20%RH 标示区有无由蓝色变为粉红色.如漏气或变色现象,请联系厂家或退回厂家高温除湿处理,(高温除湿环境：120度，6H)切勿自行处理2-2. 打开包装前，LEDs需储存在温度低于30℃，湿度低于70%RH 。

亿光3535灯珠规格书

IntroductionThe 3535 package is a lighting gradehigh power LED.It is a compact package with high lumens and efficiency and is suitable for many lighting applications.FeaturesApplications◆Top view white LED ◆ Moisture Sensitivity Level: 1◆High flux output ◆White package ◆Wide viewing angle ◆Pb-free ◆RoHS compliant◆Typical viewing angle: 115°◆ANSI binning◆Reliability testing conforms to IESNA LM80 Lumen maintenance test method◆Omni-directional Bulbs ◆Linear Lighting ◆Panel LightXI35351W Series 亿光一级代理商超毅电子Table of ContentsProduct Nomenclature (3)Absolute Maximum Ratings (4)PN of the XI3535 series: Warm White LEDs (5)PN of the XI3535 series: Neutral White LEDs (6)PN of the XI3535 series: Cool White LEDs (7)Product Binning (8)Mechanical Dimension (16)Pad Configuration (16)Reflow Soldering Characteristics (18)Wavelength Characteristics (19)Typical Electrical Characteristics (19)Typical Relative Luminous Flux V.S. Forward Current (20)Typical Wavelength & Color Shift Characteristics (20)Typical Radiation Patterns (21)Emitter Tape Packaging (22)Emitter Reel Packaging (23)Product Labeling (23)Reliability Data (23)Storage Conditions (24)Revision History (26)Product NomenclatureThe product name is designated as below:XI3535– ABCDEFG–HIJKL–MNOPDesignation:AB = color [1]CD = color bin or CCT bin[1]E = Steps Mcadams binFG = min. luminous flux (lm) or radiation power (mW) performanceHI = forward voltage binJ = internal codeKL = power consumption[2]M = internal codeN = DamO = internal codeP =packaging type[3]Notes1.Table of color offerings:Color CCT range Color Rendering Index GT Cool-White4745~7050K>65KT Cool-White4745~7050K>80PT Cool-White4745~7050K>90HT Cool-White4745~7050K>93Warm-White2580~3710KLM>70Neutral-White3710K-4745KWarm White2580~3710K>80 KMNeutral-White3710K-4745KWarm White2580~3710K>90 PMNeutral-White3710K-4745KWarm White2580~3710K>93 HMNeutral-White3710K-4745K2.Table of power consumptions:Description011W3.Table of packaging types:DescriptionP TapeAbsolute Maximum RatingsMax. DC Forward Current (mA)IF350mA Max. Peak Pulse Current (mA)IPulse720mA Power Dissipation Pd1WThermal Resistance R th15°C/WOperating Temperature Topr-40 ~ +85°CStorage Temperature Tstg-40 ~ +100°CJunction temperature Tj115°C Max. Soldering Temperature T Sol260Notes:1.Maximum forward current for 1W is 350mA (Solder Pad=25°C).2.Duty cycle = 1/10@1KHZMin. LuminousFlux(lm)Typ.LuminousFlux(lm)CCT (K)Wavelength(nm)ForwardVoltage(V)ForwardCurrent(mA)CRI(Min.)XI3535-KM277F9-03201-000P9010027K-1,27K-227K-3,27K-42.95-3.8535080XI3535-KM307F9-03201-000P9010430K-1,30K-230K-3,30K-42.95-3.8535080XI3535-KM357F9-03201-000P9010535K-1,35K-235K-3,35K-42.95-3.8535080XI3535-HM307F8-03201-000P808430K-1,30K-230K-3,30K-42.95-3.8535093Notes:1.Luminous flux measurement tolerance: ±10%.2.The data of luminous flux measured at thermal pad=25°C3.Typical luminous flux or light output performance is operated within the condition guided by this datasheet4.The CRI value is based on the Everlight testing instrument.5.CRI measurement tolerance:±2.Min. LuminousFlux(lm)Typ.LuminousFlux(lm)CCT (K)Wavelength(nm)ForwardVoltage(V)ForwardCurrent(mA)CRI(Min.)XI3535-KM407F9-03201-000P9010740K-1,40K-240K-3,40K-42.95~3.8535080Notes:1.Luminous flux measurement tolerance: ±10%.2.The data of luminous flux measured at thermal pad=25°C3.Typical luminous flux or light output performance is operated within the condition guided by this datasheet4.The CRI value is based on the Everlight testing instrument.5.CRI measurement tolerance:±2.PN of the XI3535 series: Cool White LEDsMin. LuminousFlux(lm)Typ.LuminousFlux(lm)CCT (K)Wavelength(nm)ForwardVoltage(V)ForwardCurrent(mA)CRI(Min.)XI3535-KT507J1-03201-000P10011050K-1,50K-250K-3,50K-42.95-3.8535080XI3535-KT577J1-03201-000P10011157K-1,57K-257K-3,57K-42.95-3.8535080XI3535-KT607J1-03201-000P10010957K-2,57K-365K-1,65K-42.95-3.8535080XI3535-KT657J1-03201-000P10010865K-1,65K-265K-3,65K-42.95-3.8535080XI3535-PT577F9-03201-000P909757K-1,57K-257K-3,57K-42.95-3.8535090Notes:1.Luminous flux measurement tolerance: ±10%.2.The data of luminous flux measured at thermal pad=25°C3.Typical luminous flux or light output performance is operated within the condition guided by this datasheet4.The CRI value is based on the Everlight testing instrument.5.CRI measurement tolerance:±2.Product BinningLuminous Flux Bins14511001102562110120368312013048104130140510135140150613176150160717207160180820238180200E 92327J9200225127331225250233392250275339453275300445524300325552605325350660706350375770807375400880908400425F 990100K9425450White Bin StructureNotes:1.The CCT range of Cool-White varies from 4745K to 7050K.2.The CCT range of Neutral-White varies from 3710K to 4745K.3.The CCT range of Warm-White varies from 2580K to 3710K4.Color coordinates measurement allowance : ±0.015.Color bins are defined at I F =350mA operationCool-White Bin StructureChromaticity specification defined by ANSI亿光一级代理商超毅电子Cool-White Bin Coordinates5000K0.3460.3690.3380.3620.3450.3560.3370.3490.3530.3620.3450.35650K-10.3550.37650K-20.3460.369Reference Range: 4745~5000K Reference Range: 5000~5310K 0.3450.3560.3370.3490.3440.3430.3370.3370.3520.3490.3440.34350K-40.3530.36250K-30.3450.356Reference Range: 4745~5000K Reference Range: 5000~5310K 5700K0.3290.3540.3210.3460.3290.3420.3220.3350.3370.3490.3290.34257K-10.3380.36257K-20.3290.354Reference Range: 5310~5700K Reference Range: 5700~6020K CIE X CIE Y Bin CIE X CIE Y 0.3290.3420.3220.3350.3290.3310.3220.3240.3370.3370.3290.33157K-40.3370.34957K-30.3290.342Reference Range: 5310~5700K Reference Range: 5700~6020K 6000KCIE X CIE Y BinCIE X CIE Y 0.3210.3460.3120.3390.3220.3350.3130.3290.3290.3420.3210.33757K-20.3290.35465K-10.3210.348Reference Range: 5700~6020K Reference Range: 6020~6500K CIE X CIE Y Bin CIE X CIE Y 0.3220.3350.3130.3290.3220.3240.3150.3190.3290.3310.3220.32657K-30.3290.34265K-40.3210.337Reference Range: 5700~6020K Reference Range: 6020~6500K 6500KCIE X CIE Y BinCIE X CIE Y 0.3120.3390.3030.3300.3130.3290.3050.3210.3210.3370.3130.32965K-10.3210.34865K-20.3120.339Reference Range: 6020~6500K Reference Range: 6500~7050K 亿光一级代理商超毅电子0.3130.3290.3050.3210.3150.3190.3070.3110.3220.3260.3150.31965K-40.3210.33765K-30.3130.329Reference Range: 6020~6500KReference Range: 6500~7050KNote:1.Color coordinates measurement allowance : ±0.01.Neutral-White Bin StructureNeutral-White Bin Coordinates4000KCIE X CIE Y BinCIE X CIE Y 0.3870.3960.3740.3870.3830.3800.3700.3730.3950.3880.3830.38040K-10.4010.40440K-20.3870.396Reference Range: 3710~4000K Reference Range: 4000~4260K CIE X CIE Y Bin CIE X CIE Y 0.3830.3800.3700.3730.3780.3650.3670.3580.3900.3720.3780.36540K-40.3950.38840K-30.3830.380Reference Range: 3710~4000K Reference Range: 4000~4260K4500K0.3640.3810.3550.3740.3620.3660.3530.3600.3700.3730.3620.36645K-10.3740.38745K-20.3640.381Reference Range: 4260~4500K Reference Range: 4500~4745K 0.3620.3660.3530.3600.3590.3520.3510.3470.3670.3580.3590.35245K-40.3700.37345K-30.3620.366Reference Range: 4260~4500KReference Range: 4500~4745K Note:1.Color coordinates measurement allowance : ±0.01.Warm-White Bin StructureWarm-White Bin Coordinates2700KCIE X CIE Y BinCIE X CIE Y 0.469 0.429 0.4560.4260.459 0.4100.4470.4080.470 0.413 0.4590.41027K-10.481 0.43227K-20.4690.429Reference Range: 2580~2700K Reference Range: 2700~2870K CIE X CIE Y Bin CIE X CIE Y 0.459 0.410 0.447 0.408 0.448 0.3920.437 0.3890.459 0.394 0.448 0.392 27K-40.470 0.41327K-30.459 0.410Reference Range: 2580~2700K Reference Range: 2700~2870K 3000KCIE X CIE Y BinCIE X CIE Y 0.4430.4210.4300.4170.4350.4030.4220.3990.4470.4080.4350.40330K-10.4560.42630K-20.4430.421Reference Range: 2870~3000K Reference Range: 3000~3220K CIE X CIE Y Bin CIE X CIE Y 0.4350.4030.4220.3990.4260.3850.4150.3810.4370.3890.4260.38530K-40.4470.40830K-30.4350.403Reference Range: 2870~3000K Reference Range: 3000~3220K3500K0.4150.4090.4000.4020.4080.3920.3940.3850.4220.3990.4080.39235K-10.4300.41735K-20.4150.409Reference Range: 3220~3500K Reference Range: 3500~3710K 0.4080.3920.3940.3850.4020.3750.3890.3690.4150.3810.4020.37535K-40.4220.39935K-30.4080.392Reference Range: 3220~3500KReference Range: 3500~3710K Note:1.Color coordinates measurement allowance : ±0.01.Forward Voltage BinsV1 2.95 3.25V2 3.25 3.55V3 3.55 3.85Notes:1.Forward voltage measurement tolerance: ±0.1V.2.Forward voltage bins are defined at I F=350mA operation.Mechanical Dimension..4.2Notes:1.Dimensions are in millimeters.2.Tolerances unless mentioned are ±0.15mm.3.The thermal pad is electrically unity from the Anode and contact pads.4.Do not handle the device by the lens.Incorrect force applied to the lens may lead to the failure of devices.Pad ConfigurationTOP VIEW BOTTOM VIEWPAD FUNCTION1ANODE2CATHODEReflow Soldering CharacteristicsFor Reflow Processa.3535series are suitable for SMT processes.b.Curing of glue in oven must be according to standard operation flow processes.c.Reflow soldering should not be done more than twice.d.In soldering process, stress on the LEDs during heating should be avoided.e.After soldering, do not bend the circuit board.Wavelength CharacteristicsFor Cool-White,Warm-White Relative Spectral Distribution @ Solder Pad Temperature = 254005006007008000.00.20.40.60.81.0Warm-white-CRI>80 Nature-white-CRI>80 Cool-white-CRI>80 Warm-white-CRI>90 Cool-white-CRI>90R e l a t i v e L u m i n o u s I n t e n s t i yWavelength(nm)Typical Electrical CharacteristicsFor Cool-White,Warm-White @ Solder Pad Temperature = 25501001502002503003502.52.62.72.82.93.03.13.23.3F o r w a r d V o l t a g e (V )Forward Current(mA)Typical Relative Luminous Flux V.S. Forward CurrentFor Cool-White ,Warm-White @ Solder Pad Temperature = 250501001502002503003500.00.20.40.60.81.0R e l a t i v e L u m i n o u s I n t e n s i t yForward Current(mA)Typical Wavelength & Color Shift CharacteristicsV.S. Forward CurrentFor Cool-White , Warm-White @ Solder Pad Temperature = 2550100150200250300350200030004000500060007000Cool-White Warm-WhiteC C TForward Current(mA)Forward Current Derating Curve @ Junction Temperature <11520406080100100150200250300350400F o r w a r d C u r r e n t (m A )Soldering Temperature oCTypical Radiation Patterns3535 series:Typical Diagram Characteristics of Radiation for Warm-White andCool-White108090Notes:1.2θ1/2 is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value.2.View angle tolerance is ± 5∘.Emitter Tape Packaging MOQ>2Kpcs, multiple of 400pcs per reel,max 1600pcs MOQ <2Kpcs, multiple of 100pcs per reel,max 1600pcsEmitter Reel Packaging Reel DimensionsNotes:1.Dimensions are in millimeters.2.Tolerances unless mentioned are ±0.1mm.Product LabelingLabel ExplanationCPN: Customer Specification (when required)P/N : Everlight Production NumberQTY: Packing QuantityCAT: Luminous Flux (Brightness) BinHUE: Color BinREF: Forward Voltage BinLOT No: Lot NumberMADE IN TAIWAN: Production PlaceReliability DataReflow Tsol=260 , 10sec 3 timesThermal ShockH 100 20min.'∫ 10sec.'L 10 20min.500,1000 CyclesPower Temperature Cycle H 85 15min.'∫ 5min.'L 40 15min.IF=350mA500,1000 CyclesHigh Temperature/HumidityOperationTa=85 , RH=85%, IF=225mA1000hoursRoom Temperature OperationLifeTa=25 , IF=350mA1000hoursHigh Temperature OperationLife #1Ta=55 , IF=350mA1000hoursHigh Temperature OperationLife #2Ta=85 , IF=225mA1000hoursLow Temperature OperationLifeTa=-40 , IF=350mA1000hoursPulse 30ms ON/2500ms OFF / 30000 CyclesIF=720mA30ms ON/2500ms OFF /30000 CyclesFailure Criteria:1.LEDs are open or shorted2.lm: luminous flux attenuate difference(1000hrs)>50%3.VF: forward voltage difference(1000hrs)>20%Storage Conditions⏹Before the package is opened: The LEDs should be stored at 30°C or less and 50%RH or less after beingshipped from Everlight.The storage life is6 months. If the LEDs are to be stored for more than 6months, they should be stored in a sealed container with a nitrogen atmosphere and moisture absorbent material.⏹After opening the package: The LED's should be stored under 30 or less and 30%RH or less. The LEDshould be used within 168hrs (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages.⏹Before using LEDs: The LEDs should be baked under the following conditions: pre-curing at 60±5 for 24hours.⏹Do not stack assemblies containing Everlight XI3535 LEDs to prevent damage to the optical surface ofLEDs. Forces applied to the optical surface may result in the surface being damaged.Revision HistoryCurrent version: 06.19.2013Issue No:DHE-0002027Version: 10Created by: Betty HongP5,P6,P7New 3000K 4000K 5000K Series.2012-12-07 P7New XI3535-KT657J1-03201-000P2013-02-07 P4Change the Max. Peak Pulse Current2013-03-13 P5,P7Create New CRI>90 spec2013-03-26P21MOQ>2Kpcs, multiple of 400pcs per reelMOQ <2Kpcs, multiple of 100pcs per reel2013-04-09P23Create Reliability Data2013-04-18 P21Create Package Quantity max 1600pcs2013-05-28 P5,P7Added the 4000K and 6000K Color06-19-2013。

3535灯参数

温度：-50℃-150℃
JEITA ED-4701
/
Temperature: -50℃-150℃
200 201
温度：-50℃-150℃
JEITA ED-4701
/
Temperature: -50℃-150℃
200 202
/
/
高温试验箱
高温高湿寿命试验
high-temperatur
/
Steady State
本产品最多只可回焊两次,且在首次回焊后须冷却至室温之后方可进行第二次回焊.
Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and Second soldering process.
e test chamber
Ta=60℃ RH=90%
6
Operating Life of
IF=20mA(R,G,Y)/15mA(W,B)
High Humidity &
空气加湿器 air
Temperature
/ humidifier
空气湿度表 air /
hygrometer
可焊性（回流焊）
7
Soderability (Reflow
最大绝对额定值
项目 Item
符号 Symbol
Absolute Maximum Rating
Blue
Green
Red
正向电流 Forward Current
IF
30
30
50
正向峰值电流 Pulse Forward Current

3535RGB规格书(中文)A8-A

Device No. : LDS-3535 -001
Rev.: A
Prepared date: 2016-12-24
Prepared by: calvin chai
Page: 6 of 8
Technical Data Sheet 3535 Top View LEDs
4. 反压保护 4-1. 通常 LED 的反向漏电流都很小，不会影响正常使用，如果 LED 长期遭受超过其所能承受的反向电压冲击时，LED 会被损伤，例如，反向漏电流会迅速变大等，这样会引起显示屏零灰度下串光的发生。在设计中，要注意控制反向电压，建议加在 LED 上的反向电压值不超过 5V。 5. 温度保护 5-1. LED 在高温条件下，衰减会加速，本身应力也会增大，若长期处于高温环境下，容易出现失效，对于高密度排列使用的情况，建议在使用过程中灯面温度不超过 55℃，灯脚温度不超过 75℃。 6. 其它事项 6-1. 直接用手拿取产品不但会污染封装树脂表面，也可能由于静电等因素导致产品性能的改变，过度的压力也可能直接影响封装内部的晶片和金线，因此请勿对产品施加过度压力，特别当产品处于高温状态下，例如在回流焊接过程中。 6-2. LED 的环氧树脂封装部分相对脆弱，请勿用坚硬、尖锐的物体刮、擦封装树脂部分，在用镊子夹取的时候也应当小心注意。
Prepared by: calvin chai
Page: 5 of 8
Technical Data Sheet 3535 Top View LEDs
■ 使用说明
1. 储存 1-1. 开封前请先检查包装袋有无漏气,开包后检查湿度标示卡 20%RH 标示区有无由蓝色变为粉红色.如
漏气或变色现象,请联系厂家重新烘烤使用。 1-2. 打开包装后，在温度低于 30℃ ，湿度低于 60%RH 的情况下，且开封到焊接完成控制在 12H。

ProLight Phenix 3535 60°视角高功率 LED 产品说明书

No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, Introduction‧ProLight Phenix 3535-viewing angle 60°, is one of the smallest high power LED footprint available by ProLight Opto, has offered extended solid-state lighting design possibilities. ProLight Phenix 3535-viewing angle 60°is designed with ProLight own Patents and using copper leadframe, the best thermal material of the world.‧Phenix 3535-viewing angle 60°qualifies as the JEDEC Level 1 MSL sensitivity level and suitable for SMD process, Pb_free reflow soldering capability, and full compliance with EU Reduction of Hazardous Substances (RoHS) legislation.ProLight PK2B-3JLE-GNVL 3W UV-L Power LED Technical Datasheet Version: 1.0Features‧100% foot print compatible with Cree XP-C / XP-E / XP-G‧Best thermal material solution of the world ‧Best Moisture Sensitivity:JEDEC Level 1‧RoHS compliant2018/09Main Applications‧UV gluing, UV curing, UV marking‧UV drying of printing inks and lacquers ‧Currency inspection‧Forensic analysis -urine, protein stains ‧Leak detection using fluorescent dyes ‧Detects fluorescing minerals and gems ‧Indoor Lighting ‧Outdoor LightingEmitter Mechanical DimensionsNotes:1. The cathode side of the device is denoted by the chamfer on the part body.2. Electrical insulation between the case and the board is required. Do not electrically connecteither the anode or cathode to the slug.3. Drawing not to scale.4. All dimensions are in millimeters.5. Unless otherwise indicated, tolerances are ±0.10mm.6. Please do not solder the emitter by manual hand soldering, otherwise it will damage the emitter.7. Please do not use a force of over 0.3kgf impact or pressure on the lens of the LED, otherwiseit will cause a catastrophic failure.*The appearance and specifications of the product may be modified for improvement without notice.2No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,Flux Characteristics, T J = 25°CRadiation Pattern ColorPart NumberEmitterRadiometric Power (mW)@500mARefer@350mARefer@700mAMinimum Typical Typical TypicalLambertian UV-L PK2B-3JLE-GNVL100011508151570●ProLight maintains a tolerance of ±10% on flux and power measurements.●Please do not drive at rated current more than 1 second without proper heat sink.ThermalForward Voltage VF(V)Resistance@500mA Refer @350mA Refer @700mA Junction to Color Min.Typ.Max.Typ.Typ.Slug (°C/ W) UV-L 3.00 3.40 3.80 3.32 3.498●ProLight maintains a tolerance of ±0.1V for Voltage measurements.Electrical Characteristics, T J= 25°COptical Characteristics at 500mA, T J= 25°CTotalincluded ViewingAngle AngleRadiationColor Peak Wavelength λP(degrees)(degrees)Pattern Min.Typ.Max.θ0.90V 2 θ1/2Lambertian UV-L400 nm405 nm410 nm16060●ProLight maintains a tolerance of ±3nm for dominant wavelength measurements.No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,3No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, ParameterUV-LDC Forward Current (mA)700Peak Pulsed Forward Current (mA)1000 (less than 1/10 duty cycle@1KHz)ESD Sensitivity±1000V (HBM per MIL-STD-883E Method 3015.7)LED Junction Temperature 100°C Operating Board Temperature -40°C -85°Cat Maximum DC Forward Current Storage Temperature -40°C -100°C Soldering Temperature JEDEC 020c 260°CAllowable Reflow Cycles 3Reverse VoltageNot designed to be driven in reverse biasColorBin Code MinimumMaximumAvailable Radiometric Power (mW)Radiometric Power (mW)Color BinsUV-LV110001100AllV211001210【1】W112101330【1】W213301460【1】●ProLight maintains a tolerance of ±10% on flux and power measurements.●The flux bin of the product may be modified for improvement without notice. ●【1】The rest of color bins are not 100% ready for order currently. Please ask for quote and order possibility.Radiometric Power Bin Structure at 500mAAbsolute Maximum Ratings4Color Bin CodeMinimum Peak Maximum Peak Wavelength (nm)Wavelength (nm)UV-L 3400405 4405410●ProLight maintains a tolerance of ±3nm for peak wavelength measurements.Peak Wavelength Bin StructureForward Voltage Bin StructureColor Bin Code Minimum Voltage (V)Maximum Voltage (V)UV-L B 3.0 3.2D 3.2 3.4E 3.4 3.6F 3.6 3.8●ProLight maintains a tolerance of ±0.1V for Voltage measurements.Note: Although several bins are outlined, product availability in a particular bin varies by production run and by product performance. Not all bins are available in all colors.No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,5No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 0.00.20.40.60.81.0250300350400450500550600650700R e l a t i v e S p e c t r a l P o w e r D i s t r i b u t i o nWavelength (nm)020406080100120140160020406080100120R e l a t i v e L i g h t O u t p u t (%)Junction Temperature, T J (℃)UV-L1. UV-L6Color Spectrum, T J = 25°CLight Output CharacteristicsRelative Light Output vs. Junction Temperature at 700mANo. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 01002003004005006007008000.01.02.03.04.05.0A v e r a g e F o r w a r d C u r r e n t (m A )Forward Voltage (V)0.00.20.40.60.81.01.21.41.6200400600800R e l a t i v e R a d i o m e t r i c P o w e rForward Current (mA)0100200300400500600700800020406080100F o r w a r d C u r r e n t (m A )Ambient Temperature (℃)R θJ-A = 30°C/W R θJ-A = 20°C/W R θJ-A = 25°C/W R θJ-A = 15°C/WForward Current Characteristics, T J = 25°CFig 1. Forward Current vs. ForwardVoltage for UV-L.Fig 2. Relative Radiometric Power vs.Forward Current for UV-L at T J =25 maintained.7Ambient Temperature vs. Maximum Forward Current1. UV-L (T JMAX = 110°C)No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 0102030405060708090100-100-80-60-40-2020406080100R e l a t i v e I n t e n s i t y (%)Angular Displacement (Degrees)8Typical Representative Spatial Radiation PatternRadiation PatternSoak RequirementsLevel Floor Life Standard Accelerated Environment Time Conditions Time (hours)Conditions Time (hours)Conditions1Unlimited≤30°C /168 +5/-085°C /NA NA 85% RH85% RH●The standard soak time includes a default value of 24 hours for semiconductor manufature'sexposure time (MET) between bake and bag and includes the maximum time allowed out ofthe bag at the distributor's facility.●Table below presents the moisture sensitivity level definitions per IPC/JEDEC's J-STD-020C.Soak Requirements Level Floor Life Standard Accelerated Environment Time Conditions Time (hours)Conditions Time (hours)Conditions1Unlimited≤30°C /168 +5/-085°C /NA NA 85% RH85% RH2 1 year≤30°C /168 +5/-085°C /NA NA 60% RH60% RH2a 4 weeks≤30°C /696 +5/-030°C /120 +1/-060°C / 60% RH60% RH60% RH3168 hours≤30°C /192 +5/-030°C /40 +1/-060°C / 60% RH60% RH60% RH472 hours≤30°C /96 +2/-030°C /20 +0.5/-060°C / 60% RH60% RH60% RH548 hours≤30°C /72 +2/-030°C /15 +0.5/-060°C / 60% RH60% RH60% RH5a24 hours≤30°C /48 +2/-030°C /10 +0.5/-060°C / 60% RH60% RH60% RH6Time on Label≤30°C / Time on Label30°C /NA NA (TOL)60% RH(TOL)60% RHMoisture Sensitivity Level -JEDEC Level 1No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,9No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, Stress TestStress Conditions Stress Duration Failure CriteriaRoom Temperature 25°C, I F = max DC (Note 1)1000 hours Note 2Operating Life (RTOL)High Temperature 100°C, non-operating 1000 hours Note 2Storage Life (HTSL)Low Temperature -40°C, non-operating 1000 hours Note 2Storage Life (LTSL)Non-operating-40°C to 100°C, 30 min. dwell,200 cyclesNote 2Temperature Cycle (TMCL)<5 min. transferMechanical Shock 1500 G, 0.5 msec. pulse, Note 35 shocks each 6 axis Natural Drop On concrete from 1.2 m, 3X Note 3Variable Vibration10-2000-10 Hz, log or linear sweep rate,Note 3Frequency20 G about 1 min., 1.5 mm, 3X/axisSolder Heat Resistance260°C ±5°C, 10 sec.Note 3(SHR)SolderabilitySteam age for 16 hrs., then solder dipSolder coverageat 260°C for 5 sec.on leadNotes:1. Depending on the maximum derating curve.2. Criteria for judging failureItemTest Condition Criteria for Judgement Min.Max.Forward Voltage (V F )I F = max DC --Initial Level x 1.1Luminous Flux or I F = max DCInitial Level x 0.7--Radiometric Power (ΦV )* The test is performed after the LED is cooled down to the room temperature.3. A failure is an LED that is open or shorted.10Qualification Reliability TestingNo. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, TYPE A.11Recommended Solder Pad DesignStandard Emitter ●All dimensions are in millimeters.●Electrical isolation is required between Slug and Solder Pad.TYPE B.No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 12Reflow Soldering ConditionProfile FeatureSn-Pb Eutectic Assembly Pb-Free Assembly Average Ramp-Up Rate 3°C / second max.3°C / second max.(T Smax to T P )Preheat–Temperature Min (T Smin )100°C 150°C –Temperature Max (T Smax )150°C 200°C –Time (t Smin to t Smax )60-120 seconds 60-180 seconds Time maintained above:–Temperature (T L )183°C 217°C –Time (t L )60-150 seconds60-150 secondsPeak/Classification Temperature (T P )240°C 260°C Time Within 5°C of Actual Peak 10-30 seconds 20-40 seconds Temperature (t P )Ramp-Down Rate6°C/second max.6°C/second max.Time 25°C to Peak Temperature6 minutes max.8 minutes max.●We recommend using the M705-S101-S4 solder paste from SMIC (Senju Metal Industry Co., Ltd.) for lead-free soldering.●Do not use solder pastes with post reflow flux residue>47%. (58Bi-42Sn eutectic alloy, etc) This kind of solder pastes may cause a reliability problem to LED.●All temperatures refer to topside of the package, measured on the package body surface.●Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.●Reflow soldering should not be done more than three times.●When soldering, do not put stress on the LEDs during heating.●After soldering, do not warp the circuit board.t 25°C to Peakt S PreheatTimeT e m p e r a t u r eCritical Zone T L to T PRamp-upRamp-downT SmaxT Smint Pt LT PT L25IPC-020cNotes:1. Drawing not to scale.2. All dimensions are in millimeters.3. Unless otherwise indicated, tolerances are ±0.10mm.13 No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320, 14Notes:1. Empty component pockets sealed with top cover tape.2. 250, 500 pieces per reel.3. Drawing not to scale.4. All dimensions are in millimeters.178 ± 13 ± 0.54 ± 0.5 5 ± 0.560 ± 0.513.2 ± 0.516.2 ± 0.5Φ 13.1 ± 0.5Φ 21 ± 0.5Precaution for Use●StoragePlease do not open the moisture barrier bag (MBB) more than one week. This may cause theleads of LED discoloration. We recommend storing ProLight’s LEDs in a dry box after openingthe MBB. The recommended storage conditions are temperature 5 to 30°C and humidity lessthan 40% RH. It is also recommended to return the LEDs to the MBB and to reseal the MBB.●The slug is is not electrically neutral. Therefore, we recommend to isolate the heat sink.●We recommend using the M705-S101-S4 solder paste from SMIC (Senju Metal IndustryCo., Ltd.) for lead-free soldering.●Do not use solder pastes with post reflow flux residue>47%. (58Bi-42Sn eutectic alloy, etc) Thiskind of solder pastes may cause a reliability problem to LED.●Any mechanical force or any excess vibration shall not be accepted to apply during coolingprocess to normal temperature after soldering.●Please avoid rapid cooling after soldering.●Components should not be mounted on warped direction of PCB.●Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,a heat plate should be used. It should be confirmed beforehand whether the characteristics ofthe LEDs will or will not be damaged by repairing.●This device should not be used in any type of fluid such as water, oil, organic solvent and etc.When cleaning is required, isopropyl alcohol should be used.●When the LEDs are illuminating, operating current should be decide after considering thepackage maximum temperature.●The appearance, specifications and flux bin of the product may be modified for improvementwithout notice. Please refer to the below website for the latest datasheets./Handling of Silicone Lens LEDsNotes for handling of silicone lens LEDs●Please do not use a force of over 0.3kgf impact or pressure on the silicone lens,otherwise it will cause a catastrophic failure.●The LEDs should only be picked up by making contact with the sides of the LED body.●Avoid touching the silicone lens especially by sharp tools such as Tweezers.●Avoid leaving fingerprints on the silicone lens.●Please store the LEDs away from dusty areas or seal the product against dust.●When populating boards in SMT production, there are basically no restrictionsregarding the form of the pick and place nozzle, except that mechanical pressureon the silicone lens must be prevented.●Please do not mold over the silicone lens with another resin. (epoxy, urethane, etc)15 No. 89, Xiyuan Rd., Zhongli City, Taoyuan County 320,。

成兴光电子科技有限公司-3535双波紫外杀菌灯珠XL-3535UV2SB12P2产品说明书

产品承认书产品名称：3535双波紫外杀菌灯珠5-8mw产品型号：XL-3535UV2SB12P2客户名称：客户料号：承认日期：深圳市成兴光电子科技有限公司制定审核核准客户承认栏确认审核核准目录1.产品特性2.应用领域3.产品参数4.极限使用条件5.产品规格6.典型特性曲线7.产品包装与运输8.焊接建议9.使用建议和说明10.免责声明产品规格书1.产品特性◆高光输出功率；◆寿命长，低光衰；◆环保，节能，高可靠性；◆耐用，防冲击，易设计，适合在多领域应用；◆内置UVA+UVC 双波长芯片，独特设计应用更广泛；2.应用领域◆杀菌消毒；◆空气和水净化；◆紫外探测与通讯技术；◆食品加工保鲜、食品饮料的包装，生鲜储存等；◆医疗卫生，皮肤病治疗等；3.产品参数类型参数符号测试条件最小值典型值最大值单位UVC正向电压Vf1If =50mA 4.568V Vf3If=10uA 4——V 反向电流Ir Vr =-5V —— 1.0uA 反向电压Vr Ir=-10μA 10——V 辐射功率Φe If =50mA 5—8mw 峰值波长WLP If =50mA 260—280nm 半波宽HW If =50mA 8--14nm UVA正向电压Vf1If =60mA 3.0— 3.3V Vf3If=10uA 2.2——V 反向电流Ir Vr =-10V —— 1.0uA 反向电压Vr Ir=-10μA 5——V 辐射功率Φe If =60mA 15—60mw 峰值波长WLPIf =60mA390—410nm注：◆产品测试环境@Tc=22℃；◆可根据客户要求定制特殊规格产品，可根据客户要求对产品参数进行细分；◆上述特性数据源自深圳市成兴光电子科技有限公司测量设备，其正向电压、峰值波长、辐射功率的测量误差分别为±0.2V、±3nm 和±10%；◆本产品详细参数之分类细则及标签代码命名规则将另行提供。

3535黄色灯珠规格书

Parramtter(参数）
sxmbol标准
Min最小值
typ中间值
Max最大值
Unit单位
Test couditian测试条件
Luminous Intensity(亮度)
IV
mcd
IF=350mA
Luminous flux(光通量）
Φ
35
50
LM
IF=350mA
wave Lemgth(波长)
入
585
CCT
K
IF=350mA
Forward Voltage（正向电压）
VF
2.0
2.4
V
IF=350mA
Reverse Current(反向电流)
IR
5
μ A
VR=5V
Color renderinging dex（显色指数）
CRI (Ra)
％
IF=350mA
产品名称：
产品型号：XPC3535Y-1W
参数（Parameter)绝对最大额定值TA>25℃(Absolute marimum Rating at TA=25℃)
产品名称
产品属性
型号
XPC3535Y-1W
XPC3535Y-3W
XPC3535Y-1W
尺寸规格
3535
3535
3535
外形尺寸（mm）
3.45*3.45
3.45*3.45
3.45*3.45
功率W
1W
3
1W
芯片品牌
光宏
光宏
光宏
显色指数
工作电压（v）
2.0-2.4
2.0-2.4
2.0-2.4
工作电流（mA）

3535 N302B7 产品规格书说明书

产品规格书 Product Specification文件编号 Document number WE-WI-RD-962 版本版次Version editionA/0产品名称 Product name 3535内封ICN302B7产品规格Product specificationWE-3535AY0203Z-001文件编制 Documentation 马明海批准发行Approved issue马小其客户服务 Custormer Service 联系电话 Contact number客户名称 Customer name 样品编号 Sample number产品验证 Product verification批准承认 Recognition approval注： 1.此规格书以中英文方式书写，若有冲突以中文版文本为准。

/This specification is written in both Chinese and English. In case of conflict, the Chinese version shall prevail.2.此规格书的最终解释权归由本公司。

/The final interpretation of this specification shall be vested in the company.目录Catalog0.0、封面/co ver ..........................................................................第1页page 10.1、目录/Catalog ......................................................................... 第2页page 21、产品概述/Product Overview ..............................................................第3页page 32、功能特点/Functional characteristics.....................................................第3页page 33、应用领域/Application area ..............................................................第3页page 34、外观描述 /Appearance description ......................................................第4页page 45、封装尺寸/Size .........................................................................第4页page 46、脚位图/Foot map .........................................................................第5页page 5第5页page 5 7、最大额定值/MaximumRating ............................................................第6页page 6 8、推荐工作范围/Recommended scope ofwork .................................................9、电气参数/Electrical parameters..........................................................第6页page 610、开关特性/Switching第7页page 7 characteristics.....................................................11、内置LED参数/Built-in LED parameters..................................................第7页page 712、功能说明/Description of functions......................................................第7页page 713、恒流曲线/Constant-current第10页page 10 curve........................................................14、应用线路图/Application Route Diagram..................................................第10页page 1015、使用注意事项/Precautions ............................................................第11页page 111、产品概述/Product Overview：N302B7-3535RGB是一款集成高质量单线级联恒流驱动IC N302B7和高质量RGB LED芯片的外控恒流3535集成灯珠。

3535RGB规格书(中文)C16-A

Prepared by: calvin chai
Page: 5 of 8
Technical Data Sheet 3535 Top View LEDs
■ 使用说明
1. 储存 1-1. 开封前请先检查包装袋有无漏气,开包后检查湿度标示卡 20%RH 标示区有无由蓝色变为粉红色.如
漏气或变色现象,请联系厂家重新烘烤使用。 1-2. 打开包装后，在温度低于 30℃ ，湿度低于 60%RH 的情况下，且开封到焊接完成控制在 12H。
7. 焊接指导 1.手工焊接 7-1. 如使用烙铁手工焊接，建议使用小于 25W 的电烙铁，烙铁温度必须控制在 315℃以下，焊接时间需控制在 3 秒以内，且每个电极只能焊接一次。
Device No. : LDS-3535 -001
Rev.: A
Prepared date: 2016-12-24
Prepared by: calvin chai
5 低温储存 6 常温点亮老化 7 高温高湿
TEMP : -40℃ TEMP : 25℃ IF = 20*3mA 85℃ / 85% RH
10 秒 300 回合 300 回合 1000 小时 1000 小时 1000 小时 1000 小时
22 PCS
0/1
22 PCS
0/1
22 PCS 22 PCS 22 PCS
Iv≦
0/1
Ivt*0.5
or
Vf≦U 0/1 or
Vf≧L
0/1
22 PCS
0/1
22 PCS
0/1
Notes:
Ivt: 信赖性测试前 Iv 值； Iv: 完成信赖性测试后 Iv 值； U：规格上限值 L：规格下限值

深圳市拓展光电有限公司3535 LED光源说明书

深圳市拓展光电有限公司SHENZHEN DEVELOPMENT PHOTOELECTRIC CO., LTD SPECIFICATION Model: TZ35UVB02-059Date: 2022/5/24NO:SZTZ-DS-110Par NO: F.35.00110版本修订日期文件修订内容备注A02022/5/24首次发行林纬正制作宁鹏宇日期2022年5月24日核准林纬正日期2020年5月24日版本号A0受控日期2020年5月24日The 3535 LED light source is a high-performance energy-saving device that can handle high heat and high drivecurrent.此款3535 LED光源是一种高性能节能器件，可以处理高热量和高驱动电流。

The Purple LED light source with peak wavelength rangingfrom 300nm to315nm.紫外LED光源峰值波长为300nm ~315nm.This part has a foot print that is compatible to most of thesame size LED in the market today.此器件的焊盘兼容当今市场上大部分相同大小的LED。

FEATURES/特点n Deep UV LED with emissionwavelength between 300nm to 310nm具有发射波长的深紫外光LED在300nm至315nm.n Compatible with reflow solderingprocess兼容回流焊工艺n Low thermal resistance/热阻低n Wide viewing angle at 60°60° 大发光角度n Superior ESD protection优越的ESD保护n Environmental friendly, RoHScompliance材质环保，符合RoHS要求Note: The information in this document is subject to change without notice.注：本文件中的信息如有变更，恕不另行通知。

PQ3535磁芯与骨架规格书

PQ cores and accessories
PQ35/35
COIL FORMER
General data 12-pins PQ35/35 coil former
PARAMETER Coil former material
Pin material Maximum operating temperature Resistance to soldering heat Solderability
190
mm2
162
mm2
≈ 73 g
handbook, halfpage
36.1 ± 0.6
23.5 min 6
min
11.8 26 min ± 0.5
14.4
;;;;;;;;;;;;;;;;;;;; ± 0.25
25 34.7 ± 0.3 ± 0.25
32 ± 0.5
MBE687
Dimensions in mm.
Fig.1 PQ35/35 core set.
Core sets for general purpose transformers and power applications Clamping force for AL measurements, 80 ± 20 N.
Hale Waihona Puke GRADEAL (nH)
µe
TOTAL AIR GAP (µm)
FERROXCUBE
DATA SHEET
PQ35/35 PQ cores and accessories
Supersedes data of September 2004
2008 Sep 01
Ferroxcube
PQ cores and accessories