电磁阀规格书(车用电磁阀)
FZ-4C电磁阀技术规格书
FZ-4C型DC9V电磁阀技术规格书1.外形及主要安装尺寸图2.主要参数2.1电磁阀使用压力范围: 0.02MPa～0.8MPa，瞬间承受最大压力1.2MPa 2.2适用介质及介质温度:适用于1℃-88℃的液态水2.3适用环境温度:0℃-45℃2.4止回差力差:0.02 MPa～0.5MPa2.5额定电压:DC9V2.6线圈电阻: 26±2Ω(室温20℃时)3.技术特性及要求3.1外观及装配要求3.1.1 使用箭头表示流体控制方向或在进水端标识“IN”、出水端标识“OUT”，流体方向标志应标识正确，并标识在主体的可见位置上。
3.1.2 产品外观应标志清晰,指示流体方向正确。
3.1.3 金属件表面不应有锈蚀，塑料件不应有开裂和变形，螺纹无断牙等明显缺陷。
3.1.4 装配部分应连接可靠，铆合处无松动。
3.2 工作水压范围及启动特性3.2.1 电磁阀使用水压范围：0.02MPa～0.8MPa；在0.8MPa时电磁线圈两端施加0.9倍额定电压值，电磁阀应开启并维持住。
3.3 电源电压3.3.1当电源电压在0.9倍～1.1倍额定电压值时，在电磁阀的使用水压范围内，电磁阀应能正常开闭。
3.4 流量特性2.4.1 在电磁阀线圈两端施加0.9倍～1.1倍额定电压值，出水端流量应满足：0.02MPa时，流量≥2L/min；0.8MPa时流量≥25L/min；特殊情况下流量特性应满足客户要求。
3.5 密封性能3.5.1 内部密封性电磁阀在进水水压0.02MPa作用下历时30s，要求泄漏量小于0.1ml；在静水压0.02MPa～0.8MPa作用下，无泄漏现象。
止回端在静水压0.02Pa作用下历时30s，要求无泄漏现象。
3.5.2 外部密封性在进水水压1.0MPa作用下历时30s，电磁阀应无破裂, 无变形, 无泄漏。
3.6 工作寿命2.6.1 电磁阀在静水压0.8MPa时，1.1倍额定电压作用下，开3s关3s，持续7×24h（约105次）无异常。
卡莫兹系列3电磁阀手册2022-11-08说明书
SERIES 3 VALVES AND SOLENOID VALVESVALVES AND SOLENOID VALVES 2022/11SOLENOID, PNEUMATIC AND MANIFOLD VALVES S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E S>Series 3valves and solenoid valves2x3/2, 3/2, 5/2 and 5/3-way CC CO CP Ports: G1/8 and G1/4Series 3 solenoid valves with G1/8 and G1/4 ports have been designed in the 3/2, 2 x 3/2, 5/2, 5/3 versions and with thefollowing two devices of actuation: - Electropneumatically actuated with mechanical spring return- Electropneumatically actuated with external and internal air pressure supplySeries 3 valves are equipped with a manual override which allows a stable operation and they can use Series U or G solenoids (22x22).Pneumatically actuated valves 3/2 NC become NO when the supply is on connection 3.GENERAL DATAConstruction spool - typeValve group 2x3/2 - 3/2 - 5/2 - 5/3-way CC CO CP Materials AL body, stainless steel spool, NBR seals Ports G1/8 - G1/4Installation in any position Operating temperature 0 ÷ 60°C (with dry air at -20°C)Operating pressure see tablesFluidfiltered air, without lubrication. If lubricated air is used, it is recommended to use ISOVG32 oil. Once applied the lubrication should never be interrupted.SERIES 3 VALVES AND SOLENOID VALVES SOLENOID, PNEUMATIC AND MANIFOLD VALVES >VALVES AND SOLENOID VALVES 2022/11S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E SCODING EXAMPLETYPES OF MANUAL OVERRIDEExample of solenoid valve with a bistable standard manual Example of solenoid monostable valve (IM) and bistable valveSERIES 3 VALVES AND SOLENOID VALVESVALVES AND SOLENOID VALVES 2022/11SOLENOID, PNEUMATIC AND MANIFOLD VALVES S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E S>3/2-way solenoid valve, G1/8, monostable - Mod. 338..., Mod 348...These solenoid valves, which have electropneumatic actuation and spring return, are available in the NC (closed) or NO (open) version.*Side fixing holes not present3/2-way solenoid valve, G1/8, bistable - Mod. 338...These solenoid valves, which have electropneumatic actuation and return, assume the NC (closed) or NO (open) position depending onthe last pulse received.SERIES 3 VALVES AND SOLENOID VALVES SOLENOID, PNEUMATIC AND MANIFOLD VALVES >VALVES AND SOLENOID VALVES 2022/11S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V ES2 x 3/2-way solenoid valve, G1/8 - Mod. 338D..., 348D... e 398D...These solenoid valves are available in versions with 2 x 3/2 valves in the same valve.5/2-way solenoid valve, G1/8, monostable - Mod. 358...These solenoid valves with electropneumatic actuation and mechanical or pneumatic spring return are suitablefor controlling double-acting cylinders.S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V ES5/2-way solenoid valve, G1/8, bistable - Mod. 358...These solenoid valves with electropneumatic actuation and return are suitable for controlling double-actingcylinders.5/3-way solenoid valve, G1/8, - Mod. 368... Mod. 378... Mod. 388...CC = Centres Closed CO = Centres Open CP = Pressure CentresS E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E S3/2-way solenoid valve, G1/4, monostable - Mod. 334... Mod 344...These solenoid valves, which have electropneumatic actuation and spring return,are available in the NC (closed) or NO (open) version.3/2-way solenoid valve, G1/4, bistable - Mod. 334...These solenoid valves, which have electropneumatic actuation and return assume the NC (closed) or NO (open)position depending on ther last pulse received.S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E S2 x 3/2-way solenoid valve, G1/4 Mod. 334D... 344D... and 394D...These solenoid valves are available in versions with 2 x 3/2 valves in the same valve.5/2-way solenoid valve, G1/4, monostable - Mod. 354...These solenoid valves, which have electropneumatic actuation and spring return, are suitable for operatingdouble-acting cylinders.SERIES 3 VALVES AND SOLENOID VALVES SOLENOID, PNEUMATIC AND MANIFOLD VALVES >VALVES AND SOLENOID VALVES 2022/11S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V ES5/2-way solenoid valve, G1/4, bistable - Mod. 354...These solenoid valves, which have electropneumatic actuation and spring return, are suitable for operatingdouble-acting cylinders.5/3-way solenoid valve, G1/4, - Mod. 364... Mod. 374... Mod. 384...CC = Centres Closed CO = Centres Open CP = Pressure CentresSERIES 3 VALVES AND SOLENOID VALVESVALVES AND SOLENOID VALVES 2022/11SOLENOID, PNEUMATIC AND MANIFOLD VALVES S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E S>3/2-way valve, G1/8 or G1/4, monostable3/2-way valve, G1/8 or G1/4, bistableSERIES 3 VALVES AND SOLENOID VALVES SOLENOID, PNEUMATIC AND MANIFOLD VALVES >VALVES AND SOLENOID VALVES 2022/11S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V ES5/2-way valve, G1/8 or G1/4, monostableIn-line or manifold mounting5/2-way valve, G1/8 or G1/4, bistableIn-line or manifold mountingS E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E S5/3-way valve, G1/8 or G1/4In-line or manifold mounting2 x 3/2-way valve, G1/8 or G1/4In-line or manifold mountingS E R I E S 3 V A L V E S A N D S O L E N O I D V A L V ESManifold bars with separate exhausts (low version)The following is supplied: 2x feet1x manifold 1x inlet fitting 1x plug 4x washersManifold bars with separate exhausts (high version)The following is supplied: 2x feet1x manifold 1x inlet fitting 1x plug 4x washersS E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E SThe following is supplied:3x interface O-Rings manifold/manifold; 2x fixing nuts; 2x junction plugs;9x interface seals valve/manifold (CNVL-3H3) or 3x interface seals valve/manif. (CNVL-4H3);6x fixing screws for valvesCNVL-3H3: for Series 3, G1/8 CNVL-4H3: for Series 3, G1/4Initial / final Module with 2 positions - Mod. CNVL-...Initial module with 2 positions The following is supplied:3x interface O-Rings manifold/manifold; 2x fixing nuts; 2x junction plugs;6x interface seals valve/manifold (CNVL-3H2) or 2x interface seals valve/manif. (CNVL-4H2);4x fixing screws for valvesCNVL-3H2: for Series 3, G1/8 CNVL-4H2: for Series 3, G1/4Intermediate module with 3 positions - Mod. CNVL-...The following is supplied:3x interface O-Rings manifold/manifold;2x fixing nuts; 2x junction plugs;9x interface seals valve/manifold (CNVL-3I3) or 3x interface seals valve/manif. (CNVL-4I3);6x fixing screws for valvesCNVL-3I3: for Series 3, G1/8 CNVL-4I3: for Series 3, G1/4S E R I E S 3 V A L V E S A N D S O L E N O I D V A L V ESThe following is supplied:3x interface O-Rings manifold/manifold; 2x fixing nuts; 2x junction plugs;6x interface seals valve/manifold (CNVL-3I2) or 2x interface seals valve/manif. (CNVL-4I2);4x fixing screws for valvesCNVL-3I2: for Series 3, G1/8CNVL-4I2: for Series 3, G1/4Intermediate module with 1 position - Mod. CNVL-...The following is supplied:3x interface O-Rings manifold/manifold; 2x fixing nuts; 2x junction plugs;3x interface seals valve/manifold (CNVL-3I1) or 1x interface seal valve/manif. (CNVL-4I1);2x fixing screws for valvesCNVL-3I1: for Series 3, G1/8CNVL-4I1: for Series 3, G1/4Terminal module Mod. CNVL-*HThe following is supplied:2x fixing nutsCNVL-3H: for Series 3, G1/8CNVL-4H: for Series 3, G1/4Interface module manifold between Series 3 G1/8 and G1/4The following is supplied: 3x interface seal 2x screws 2x pins 4x plugs6x O-RingsS E R I E S 3 V A L V E S A N D S O L E N O I D V A L V E SIntermediate plate for additional inlet and exhaust pressureThe following is supplied: 3x O-Rings2x fixing screwsCNVL-3P: for Series 3, G1/8CNVL-4P: for Series 3, G1/4Separation diaphragmFor separation of channel: 1 - 3 - 5.The following is supplied:1x diaphragmBlanking plug Mod. TCNVL for manifoldsThe following is supplied:1x blanking plug1x O-RingBlanking plate Mod. CNVL for manifoldsIt is used to blank vacant positions of a manifold.The following is supplied: 2x fixing screws 3x O-Rings。
卡莫齐系列6直动电磁阀产品说明书
Directly operated solenoid valves Series 62/2-way - 3/2-way, NC and NO.Ports G1/8 and G3/8 - cartridge ø4The solenoid valves Series 6 are available as 2/2 and 3/2-way, either NCor NO.These directly operated solenoid valves can be used either with or without lubrication.The bodies of these valves can be used either individually or in manifolds.The latter are provided with G1/8 threaded ports or an inbuilt diameter 4 cartridge(G3/8 for 2-way only).GENERAL DATAValve functions2/2 - 3/2 NC or NOConstruction poppet typeMaterials body = AL / brassseals = NBR (FKM on demand)others = stainless steelMounting in any positionOperating temperature0 ÷ 80°C (with dry air - 20°C)Operating pressure see tablesNominal flow rate Qn (see tables)Nominal diameterø (see tables)Fluid filtered air, without lubrication, inert gas. If lubricated air is used, it is recommended to use ISOVG32 oil. The lubrication should never be interrupted.Voltage AC standard: 24V, 50/60Hz110V - 50/60Hz230V - 50/60HzDC standard: 24VVoltage tolerance AC + 10% -15%DC ±10%Power consumption AC at inrush = 19 VA, during operation = 12 VADC 10 WDuty cycle ED 100%Class of insulation class HConnector Mod. 124-800Protection class IP65 with connector DIN 43650/PG9Function Orifice Ø (mm)Qn (Nl/min)Pressure min-max DC (bar)Pressure min-max AC (bar)Symbol NC 21300 ÷ 10-EV03NO2800 ÷ 80 ÷ 6EV05In the mod. 648-150-A6* (NO) connections 1 and 3 are inverted, while the max operating pressure is 6 bar in case a solenoid A6B, A6C, A6D, A6E is chosen. * = choose the solenoid voltage according to the Coding example table on page 2/1.25.02.3/2-way NC solenoid valve - Mod. 638M and Mod. 63CMThese solenoid valves are equipped with a manual override and are available with G1/8 inlet ports and with G1/8 outlets or with a diameter 4 cartridge. The body is supplied complete with screws and O-ring.Outlet Function Orifice Ø (mm)Qn (Nl/min)Pressure min-max (bar)G1/8NC 21200 ÷ 10cartridge Ø 4NC21080 ÷ 10* = choose the solenoid voltage according to the Coding example table on page 2/1.25.02.Mod.Interface 600-450-A6*Swivel * = choose the solenoid voltage according to the Coding example table on page 2/1.25.02.Mod.Ports623-15E-A6*G3/8 623-15F-A6*G3/8* = choose the solenoid voltageaccording to the Coding exampletable on page 2/1.25.02.** = maximum pressures referredto 50 Hz.Mod.。
电磁阀MEH-5 3E-5,0-S-B产品说明书
Hoja de datos
Característica Función de las válvulas Tipo de accionamiento Ancho Caudal nominal normal Presión de funcionamiento Construcción Tipo de reposición Homologación Tipo de protección Diámetro nominal Patrón Función de escape Principio de hermetización Posición de montaje Accionamiento manual auxiliar Tipo de control Alimentación del aire de control Sentido del flujo Superposición Presión de control Valor B Valor C Tiempo de conmutación a la desconexión Tiempo de conmutación a la conexión Factor de utilización Valores característicos de las bobinas Fluido Indicación sobre los fluidos de funcionamiento y de mando
Comprobación de suplemento de transporte con grado de nitidez 1 según FN 942017-4 y EN 60068-2-6
Control de golpes con grado de severidad 2, según FN 942017-5 y EN 60068-2-27
电磁阀规格书(车用电磁阀)
电磁阀规格书编号：产品名称：CDF型电磁阀用途：汽车空调系统编制：校对：审核：批准：1．适用范围本规格书适用于本公司生产的以R134a、R410a为制冷剂的汽车空调系统用电磁阀。
2．术语和定义电磁阀是一种由线圈产生的电磁吸力控制内部芯铁上下活动，开闭阀口，从而控制流通介质通断的执行器件。
3．基本规格序号项目规格备注3.1 电源DC24V/DC12V3.2 电压变化额定电压的90%-110%范围3.3 最大工作压力4.2MPa3.4 额定功率<20W3.5 阀口公称通径Φ10mm3.6 适用制冷剂R134A、R410A等3.7 介质流动方向单向3.8 安装方式以阀体及线圈的断面中心线为轴，在垂直±15°以内3.9 适用环境温度-20℃～+55℃3.10 适用环境湿度95%RH以下3.11 适用液体温度-30℃～+105℃4. 环保要求4.1 阀体外表面要求耐NaCl、H2S等腐蚀；4.2 所用材料对人体无毒害且不产生有毒物质，符合RoHS要求；4.3 阀体内部结构材料需满足耐冷媒腐蚀，冲击；4.4 阀内部材料强度，刚度能满足产品性能要求；5. 外观构造5.1 外观、尺寸、构造、材质满足图纸要求。
5.2 外观无明显的伤痕、变形、氧化腐蚀、毛刺等缺陷，线圈引出线及端子完好无损。
5.3 产品由线圈与阀体组成。
5.4 阀体内部不得有切屑、油渍、锈迹等存在。
5.5 包装：接管进、出口端使用防尘帽。
6. 性能测试基本条件如下：6.1 安装：基本状态竖直安装，线圈安装在阀体上，阀体轴心线倾斜角度控制在15°以内；6.2 除有特别规定外，基本测试条件如下：6.2.1 室温（试验品）及流体温度：20±5℃；6.2.2 相对湿度：65±20%RH，无风；6.2.3 流动方向：进口管—出口管(单向)；6.2.4 电源：DC24V/DC12V；7．测试仪表要求：测试设备应在有效使用期内，并附有鉴定合格证，其仪表准确度等级应符合下列规定：①温度测量仪表准确度不低于1.0级；②压力测量仪表准确度等级不低于1.5级；③流量测量仪表准确度不低于1.5级；④电压测量仪表准确度等级不低于1.5级；⑤拉力测试仪表准确度等级不低于1.0级；⑥电阻测量仪表准确度不低于0.1级；8. 试验项目及试验方法：10. 标志、包装及贮存10.1 在电磁阀的标签上应标出下列内容：a．电磁阀型号及名称；b．额定电压；c．产品编号或生产日期；d. 制造厂名及商标；e. 介质流动方向；10.2、产品出厂时进、出气管口处应有防尘保护，并应做到清洁、防潮和防霉。
F6200VIC 电磁阀数据表说明书
F6200VICButterfly Valve with Grooved types• Disc electroless nickel coated ductile iron• Bubble tight shut-off• Resilient seat• Valve face-to-face dimensions comply withAWWA (c606) & MSS-SP-67• Completely assembled and tested, ready forinstallationType overviewType DNF6200VIC200 Technical dataFunctional data Valve size [mm]8" [200]Fluid chilled or hot water, up to 60% glycolFluid Temp Range (water)-22...250°F [-30...120°C]Body Pressure Rating ANSI Class Grooved AWWA, 300 psiFlow characteristic modified equal percentagePipe connection GroovedANSI/AWWA (c606)Servicing maintenance-freeFlow Pattern2-wayLeakage rate0%Controllable flow range90° rotationCv3400Maximum Velocity20 FPSMaterials Valve body Ductile cast iron ASTM A536Body finish black alkyd enamelStem416 stainless steelStem seal fiberglass with TFE liningSeat EPDMDisc electroless nickel coated ductile ironSuitable actuators Non Fail-Safe SY4PRB(X)F6200VICProduct featuresFlow/Mounting detailsDimensionsType DN WeightF6200VIC20035 lb [16 kg]SY4-6A B C D E F11.5" [293] 5.3" [135]29.4" [747]24.4" [620] 5.0" [127] 5.0" [127]F6200VICF6..VIC_PRAB CD E F 11.7" [298]5.3" [135]20.6" [523]15.7" [399]5.0" [127]5.0" [127]F6..VIC_PKAB D E F 11.7" [298]5.3" [135]18.6" [473]5.0" [127]5.0" [127]DimensionsPRBUP-3-TOn/Off, Floating point, Non fail-safe, 24...240 VTechnical dataElectrical data Nominal voltage AC 24...240 V / DC 24...125 VNominal voltage frequency50/60 HzRemark about nominal voltage range AC 19.2...264 V / DC 19.2...137.5 VPower consumption in operation20 WPower consumption in rest position7 WTransformer sizing with 24 V 20 VA / with 240 V 52 VAAuxiliary switch2x SPDT, 1 mA...3 A (0.5 A inductive), DC 5 V...AC250 V (II, reinforced insulation), 1x 10° / 1x0...90° (default setting 85°)Switching capacity auxiliary switch 1 mA...3 A (0.5 A inductive), DC 5 V...AC 250 V(II, reinforced insulation)Electrical Connection Terminal blocks, (PE) Ground-ScrewOverload Protection electronic thoughout 0...90° rotationFunctional data Direction of motion motor reversible with appManual override7 mm hex crank, suppliedAngle of rotation90°Running Time (Motor)35 s / 90°Noise level, motor68 dB(A)Position indication integral pointerSafety data Power source UL Class 2 SupplyDegree of protection IEC/EN IP66/67Degree of protection NEMA/UL NEMA 4XEnclosure UL Enclosure Type 4XAgency Listing cULus acc. to UL60730-1A/-2-14, CAN/CSAE60730-1:02, CE acc. to 2014/30/EU and2014/35/EUQuality Standard ISO 9001Ambient humidity Max. 100% RHAmbient temperature-22...122°F [-30...50°C]Servicing maintenance-freeWeight Weight 6.8 lb [3.1 kg]Materials Housing material Die cast aluminium and plastic casingPRBUP-3-TApplicationOperationProduct featuresPR Series valve actuators are designed with an integrated linkage and visual position indicators. For outdoor applications, the installed valve must be mounted with the actuator at or above horizontal. For indoor applications the actuator can be in any location including directly under the valve.The PR series actuator provides 90° of rotation and a visual indicator shows the position of the valve. The PR Series actuator uses a low power consumption brushless DC motor and is electronically protected against overload. A universal power supply is furnished to connect supply voltage in the range of AC 24...240 V and DC 24...125 V. Included is a smart heater with thermostat to eliminate condensation. Two auxiliary switches are provided; one set at 10° open and the other is field adjustable. Running time is field adjustable from 30...120 seconds by using the Near Field Communication (NFC) app and a smart phone.†Use 60°C/75°C copper wire size range 12...28 AWG, stranded or solid. Use flexible metal conduit. Push the listed conduit fitting device over the actuator’s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 4000 V. Type of action 1. Control pollution degree 3.AccessoriesMechanical accessoriesDescriptionType Hand crank for PR, PKR, PMZG-HND PRElectrical installationMeets cULus requirements without the need of an electrical ground connection.Universal Power Supply (UP) models can be supplied with 24 VAC up to 240 VAC, or 24 VDC upto 125 VDC.Disconnect power.Provide overload protection and disconnect as required.Two built-in auxiliary switches (2x SPDT), for end position indication, interlock control, fanstartup, etc.Actuators may be controlled in parallel. Current draw and input impedance must be observed.Warning! Live electrical components!During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.Wiring diagramsOn/OffPRBUP-3-T Wiring diagramsOn/OffFloating PointAuxiliary SwitchesElectrical installationPRBUP-3-T Dimensions。
电磁阀说明书
INSTALLATIONWARNINGDo not install unless the safety instructions have been read and understood.3.1EnvironmentWARNINGDo not use in an environment where the product is directly exposed to corrosive gases, chemicals,salt water , water or steam.Do not use in an explosive atmosphere.The product should not be exposed to prolonged sunlight. Use a protective cover Do not mount the product in a location where it is subject to strong vibrations and/or shock. Check the product specifications for above ratings.Do not mount the product in a location where it is exposed to radiant heat.Installation and Maintenance ManualSeries VKF3003 Port Direct Operated Poppet Solenoid ValveXSymbol(A)21(P)3(R)Rc 1/8(port A)Rc 1/8,M5x0.8(port A)2-M5x0.8(ports P , R)Rc 1/8(port P , R)Port A:Rc 1/8, M5x0.8Port R: Rc 1/8Port P: Rc 1/8Type 21/for body ported type (Port A top ported)Port A:Rc 1/8, M5x0.8Port P: Rc 1/8Type 20/for body ported type (Port A top ported)Port R: Rc 1/8Manifold, base mounted mon SUP, Common EXHPort R: Rc 1/8Type 42/for base mounted type (Port A side ported)Port P: Rc 1/8Type 40/for base mounted type (Port A bottom ported)Port R: Rc 1/8Port P: Rc 1/8Port A: Rc 1/8Port A: Rc 1/8Type S42(solenoid on same side as port A)Port P: Rc 1/8Port R: Rc 1/8Port A: Rc 1/8Use of DIN ConnectorLoosen the holding screw, and pull the connector out of the solenoid valve terminal block.After removing the holding screw, insert the flat head screw driver , etc. into the notch on the bottom of the terminal block and pry it up, separating the Loosen the terminal screws (slotted screws) on the terminal block, insert the core of the leadThe connector should be inserted and pulled out in a straight line without tilting diagonally. Circuit diagram for connector with lightSMC products have been lubricated for life at manufacturer , and do not require lubrication in If a lubricant is used in the system, use turbine oil Class 1(no additive), ISO VG32. Once lubricant is used in the system, lubrication must be continued because the original lubricant applied during When the manual override is operated, connected equipment will be actuated. Not following proper procedures could cause the product to malfunction and could lead to damage f handled improperly, compressed air can be dangerous. Assembly, handling and repair of pneumatic system should be performed by qualified personnel only.Drain: remove condensate from the filter bowl on a regular basis.Shut-down before maintenance: before attempting any kind of maintenance make sure the supply pressure is shut off and all residual air pressure is released from the system to be worked on.Start-up after maintenance: apply operating pressure and power to the equipment and check for f operation is abnormal, please verify product set-up Do not disassemble the product, unless required by installation or maintenance instructions.Refer to paragraph 3.4, for mounting valves onto manifolds.Operation is possible to -10°C, but measures should be taken to avoid solidification or freezing of drainage Telephone(39) 02-92711 Netherlands (31) 20-531 8888 (47) 67 12 90 20 (48) 22-548 50 85 (351) 22 610 89 22(34) 945-18 4100 (46) 8-603 0700 Switzerland (41) 52-396 3131 (90) 212 221 1512 United Kingdom(44) 1908-56 3888Red (+)Black (-)Surge voltage suppressor* MarkingLight(built into connectorSurge voltage suppressor (built intoterminal block)* MarkingsFor 24V or more DCFor AC and 12V or less DC1(-)(+)2Gland nut Washer Grommet (rubber)Holding screw Light mounting location Terminal blockNotchTerminal screw (3 places)Rating symbol (see table below)HousingACCircuit diagram12VDC or less Circuit diagram24VDC or more Circuit diagramLEDNLRLEDRR222111NL: Neon light R: ResistorLED: Light emitting diodeR: ResistorD: Protective diode LED: Light emitting diodeR: ResistorMounting screwBushingSwitching elementValveOFF Leakage currentPower supplyResistorL e a k a g e v o l t a g eHole dia. ø5ø9D。
电磁阀技术规格书
17
绝缘等级Insulation Class
F
18
防护等级Protection grade
IP65
19
防爆方式Explosion method
隔爆型
20
防爆等级Explosion Class
EXdIIBT4
21
电气接口Electrical interface
NPT1/2
22
工作温度Operation temperature
1~8bar
11
工作介质Working medium
经干燥和过滤的空气或中性气体
12
工作温度Operation temperature
-20~60°C
电
磁
线
圈
13
线圈数量Number of Coil
单线圈
14
线圈型式Type of Coil
/
15
线圈外壳材质Coil material
铝合金
16
操作电源/频率Operating power
-20~60°C
附
件
23
手动操作MANUAL
带
24
手操器HART
/
25
过流保护电路
/
26
端子板Terminal board
/
27
接线盒Junction box
/ห้องสมุดไป่ตู้
其
他
28
推荐制造商Manufacturer
/
29
要求Requirement
脱油脱脂处理
30
XXXX公司
仪表规格书（电磁阀）
Instrument specifications
电磁阀MFH-3-14-EX
排气接口 先导排气口82
24/04/2017 – 有待更新 – Festo AG & Co. KG
1/2
特性 气动连接, 气口 1 气动连接, 气口 2 气动连接, 气口 3 材料备注 密封件的材料信息 外壳的材料信息
值 G1/4 G1/4 G1/4 符合 RoHS NBR 压铸铝
24/04/2017 – 有待更新 – Festo AG & Co. KG
电磁阀 MFH-3-1/4-EX
产品代号: 535898 不带电磁线圈和插座.
技术参数
特性 阀功能 驱动类型 阀规格 宽度 标准额定流量 工作压力 设计结构 复位类型 防护等级 授权 额定尺寸 宽度尺寸 排气功能 密封原则 装配位置 手控装置 先导类型 流动方向 可自由交叠 切换时间，关闭 切换时间，打开 逻辑为0的最大正向测试脉冲 逻辑为1的最大负向测试脉冲 线圈的特性参数 ATEX 类气体 燃爆防护型气体 ATEX 类粉尘 燃爆防护型粉尘 符合防爆要求的环境温度 工作介质 关于工作和先导介质的说明 CE 符号 (参见符合的标准) 耐腐蚀等级 CRC 储藏温度 介质温度 环境温度 产品重量 电连接 安装类型 值 3/2 常闭， 单电控 电气的 30.5 mm 30.5 mm 800 l/min 1.5 ... 8 bar 提动阀座 机械弹簧 IP65 c UL us - Recognized (OL) 7 mm 32 mm 可节流 软性 任意 位置锁定 由先导控制 不可逆 否 29 ms 10 ms 2,200 µs 3,700 µs 参见电磁线圈，需单独订购 II 2G c T4 II 2D c 130 °C -5°C <= Ta <= +40°C 压缩空气符合ISO8573-1:2010 [7:4:4] 可以使用经过润滑的压缩空气 (一旦使用后要求一直使用经过润滑的压缩空气) 根据 EU-Ex 防爆指导原则 (ATEX) 1 – 低腐蚀影响 -20 ... 60 °C -5 ... 40 °C -5 ... 40 °C 320 g 通过 F 线圈, 必须另行订购 可选 在气路轨上 带通孔 M5 M5
燃油电磁阀参数
燃油电磁阀参数
燃油电磁阀是一种常用于汽车、船舶、工程机械等燃油系统中的控制元件。
其作用是控制燃油的进出，从而实现对发动机的控制。
以下是燃油电磁阀的参数介绍：
1. 电压：通常为12V或24V，根据不同的应用场景选择不同的电压。
2. 电流：燃油电磁阀的电流大小根据不同的型号和功率而不同，一般在0.5A到2A之间。
3. 温度范围：燃油电磁阀的温度范围也根据不同的型号而不同，但一般都在-40℃到+120℃之间。
4. 接口尺寸：燃油电磁阀的接口尺寸也有不同的种类，通常是1/8英寸、1/4英寸、3/8英寸等。
5. 功率：燃油电磁阀的功率也根据不同的型号而不同，一般在3W到20W之间。
6. 材质：燃油电磁阀的材质通常是黄铜或不锈钢，根据不同的应用场景选择不同的材质。
以上是燃油电磁阀的主要参数介绍，这些参数的选择应根据具体的应用场景和需求来进行。
- 1 -。
永嘉电磁阀K25D说明书
≤25
≤50
五、外形及安装尺寸
型号
通径
L
L1
L2
H
H1
H2
C
C1
D
E
E1
F
F1
G
连接螺纹M
K25D-6
6
130
132
112
130
68
28
28
9
φ14
56
1.4
14
10
24
M10×1
(G1／8")
K25D2-6
K25D-8
8
130
132
112
130
68
28
28
9
φ20
56
Hale Waihona Puke 1.8141024
M12×1.25
(G1／4")
K25D2-8
K25D-10
10
160
166
146
165
90
38
38
9
φ24
74
1.8
19
14
33
M16×1.5
(G3／8")
K25D2-10
165
K25D-15
15
160
166
146
165
90
38
38
9
φ28
74
1.8
19
14
33
M20×l.5
(G1／2")
K25D2-15
165
K25D-20
20
235
234
202
210
130
55
60
MA955电磁阀技术规格书说明书
Technical Specification: Solenoid :Inlet Connection :Outlet Connection :Pressure Range : Ambient Temperature :Fluid Temperature :Seal Material :Exterior Material : Valve Body Material :Cable Plug : Power Consumption :Working Voltage : Insulation Resistance :Electric Cable :Current Rating :Voltage Rating : Cord Specification : 4 x 6mm Hose4 x 6mm Hose0 – 10 kg/cm2 Max–10o C to +60o C–10o C to +60o CNBRPolyesterBrass or AluminiumDIN 43650B40VA in 10ms (Power-On) at AC 220V 1VA (Holding) at AC 220VAC 100V to AC 230VHigher than 100MΩ/DC 500V10AAC 250V3 Core, 0.75mm2Instruction Manual:Perform a visual inspection to ensure that all cables and electrical connections are in good conditions. Please do not connect electrical power if any of these parts are damaged.Connect all the necessary connections, including port A and port B. Please ensure that all connections are tightened properly.After ensuring that everything is connected and properly secured, connect the power plug. If power (AC 100V ~ 230V) is present, the solenoid valve will be opened. If power is disconnected, the solenoid valve will be closed.Please Note: Sometimes the solenoid valve is open before the power is connected, and gas starts to flow through when the gas connections are connected, please connect the power once and disconnect the power again to reset the position of the solenoid, which is supposed to be closed when power is absent and open when power is present.。
费斯特 CPE 2 型号电磁阀商品说明书
Universal valve CPE2d Internet: /catalogue/...Subject to change – 2022/07Solenoid valves CPE, Compact PerformanceKey featuresVariantsParameter AdvantagesFunctions (selection)3/2-way valve with external pilot air supply, normally closed5/2-way single solenoid valve with Internal pilot air supply-K- Width10 mm 14 mm 18 mm 24 mm-M-Flow rate180 ... 3200 l/minPerformance-optimised sizes:The solenoid valves CPE, Compact Performance, are distinguished by their minimal width and low power consumption at high flow rates.They can be mounted directly on site:• On the cylinder• On moving system components • Flexible installation through individual mountingShort tubing lengths requiring minimal air volume:• Short switching times • Very short reaction times Optimised installations:• Shorter machine cycles • Larger quantities• Low power consumption Convenient manual override.5/2-way double pilot valve with exter-nal pilot air supply5/3-way valve with external pilot air supply, normally closedH- -NoteThe 5/3-way solenoid valve remains in the previous switching position if both solenoid coils are energised si-multaneously.If neither solenoid coil is energised, the spring force moves the valve to its mid-position.CPE10, CPE14 and CPE18:Simple manifold design consisting of fixed-grid manifold blocks made from stable aluminium with 2 to 10 valve positions or modular manifold blocks made from durable polymer.The connecting cables NEBV for sizes CPE10 and CPE14 have integrated current reduction.All CPE valves therefore have a dutycycle of 100%.Solenoid valves CPE, Compact Performance Key features3 2022/07 – Subject to change d Internet: /catalogue/...4d Internet: /catalogue/...Subject to change – 2022/07Solenoid valves CPE, Compact PerformanceKey featuresVersions• Reserved position cover for 5/2- or 5/3-way valveSolenoid valves CPE, Compact Performance Key featuresMounting on fixed-grid manifold block for CPE10, CPE14 and CPE18• Simple design comprising compact valve manifold assemblies with in-line valves• Mounting with stable retaining bracket and special moulded seal guarantee leak-free assembly • 2 to 10 valve positions• Aluminium mounting rail provideshigh stability• High flow rates with air supply onboth sides for duct 1• High exhaust capacity with outputon both sides for ducts 3 and 5• Different pressure and exhaustzones can be created using separa-tors, which are clamped at the sep-aration points in ducts 1, 3 and 55 2022/07 – Subject to change d Internet: /catalogue/...Solenoid valves CPE, Compact PerformanceKey featuresMounting on fixed-grid manifold block for CPE10, CPE14 and CPE18• Creating a valve manifold with mod-ular manifold blocks made from high impact, glass fibre reinforced polyamide • Different pressure zones can be cre-ated using basic and expansionblocks with closed supply and ex-haust ducts• Air supply and exhaust can be con-nected on both sides using an addi-tional end block• Air supply and exhaust can be con-nected to the end block, at the rearand at the top• No screws required for mountingthanks to slides and clipsFor 3 valves6d Internet: /catalogue/...Subject to change – 2022/0772022/07 – Subject to changed Internet: /catalogue/...Solenoid valves CPE, Compact PerformanceKey features – MountingIndividual valve mounting CPECylinder mountingFor mounting individual valves directly on a drive.The solenoid valves are provided with two through-holes for attaching to the cylinder mounting DAVM-MW-V1...-V.Mounting is only possible on the side on which the pneumatic connections are located.The relevant screw set is included when the cylinder mounting DAVM-MW-V1...-V is ordered.Solenoid valves CPE, Compact PerformanceProduct range overview – Widths 10 mm and 14 mm8d Internet: /catalogue/...Subject to change – 2022/07Solenoid valves CPE, Compact Performance Product range overview – Width 18 mm1)Operating voltage dependent on separately ordered pilot valve9 2022/07 – Subject to change d Internet: /catalogue/...Solenoid valves CPE, Compact PerformanceProduct range overview – Width 24 mm10d Internet: /catalogue/...Subject to change – 2022/07Solenoid valves CPE, Compact Performance Product range overview – FunctionsSolenoid valves CPE, Compact Performance Product range overview – FunctionsSolenoid valves CPE, Compact Performance Peripherals overviewIndividual valve – CPE10 and CPE14Solenoid valves CPE, Compact Performance Peripherals overviewIndividual valve – CPE18 and CPE24Solenoid valves CPE, Compact PerformanceSystem overviewFixed-grid manifold assembly1Solenoid valves CPE, Compact Performance Peripherals overviewAccessories – Fixed-grid manifold assembly CPE10 and CPE14Solenoid valves CPE, Compact Performance Peripherals overviewAccessories – Fixed-grid manifold assembly CPE18Solenoid valves CPE, Compact Performance System overviewManifold assembly with modular manifold blocksSolenoid valves CPE10Type codesSolenoid valves CPE10 DatasheetFunction3/2G, 3/2O,5/2-way single solenoid5/2-way double pilot valve5/3G, 5/3B, 5/3Ee.g. 3/2-way valve with external pilot air supply, nor-mally closed -K-Width 10 mm -M-Flow rate180 ... 400 l/min -P- Voltage24 V DC1)G = normally closed2)O,B = normally open3) E = normally exhausted4)Corrosion resistance class CRC 2 to Festo standard FN 940070Moderate corrosion stress. Indoor applications in which condensation can occur. External visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment.Solenoid valves CPE10Datasheet1)Additional information: /sp dCertificates.MaterialsSectional view3Solenoid valves CPE10 DatasheetSolenoid valves CPE10 DatasheetSolenoid valves CPE10 DatasheetSolenoid valves CPE10 DatasheetSolenoid valves CPE10 Ordering dataSolenoid valves CPE10 Ordering dataManifold blocks CPE10 Datasheet – Manifold block Manifold block CPE...-PRSMaterial:Wrought aluminium alloyManifold blocks CPE10 Ordering data – Fixed-grid manifold block1)Corrosion resistance class CRC 2 to Festo standard FN 940070Moderate corrosion stress. Indoor applications in which condensation can occur. External visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment.Manifold blocks CPE10Technical data – Fixed-grid manifold block Manifold blockFor CPE10 3/2Material:Wrought aluminium alloyRoHS-compliantManifold blocks CPE10 Ordering data – Fixed-grid manifold block1)Corrosion resistance class CRC 2 to Festo standard FN 940070Moderate corrosion stress. Indoor applications in which condensation can occur. External visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment.Manifold blocks CPE10 Technical data – Modular manifoldFor CPE18 5/2 and 5/3Material:Reinforced PA1)n = number of valve positionsManifold blocks CPE10 Technical data – Modular manifold-NoteH-Each air supply can support a maximum of 6 valve positions. Use valvemanifold blocks only in combination with 5/2- and 5/3-way valves.Solenoid valves CPE14Type codesSolenoid valves CPE14 DatasheetFunction3/2G, 3/2O,5/2-way single solenoid5/2-way double pilot valve5/3G, 5/3B, 5/3Ee.g. 3/2-way valve with external pilot air supply, normally closed -K-Width 14 mm -M-Flow rate370 ... 900 l/min -P- Voltage24 V DC1)G = normally closed2)O,B = normally open3) E = normally exhausted4)Corrosion resistance class CRC 2 to Festo standard FN 940070Moderate corrosion stress. Indoor applications in which condensation can occur. External visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment.Solenoid valves CPE14Datasheet1)Additional information: /sp dCertificates.Sectional view3Solenoid valves CPE14 DatasheetSolenoid valves CPE14 DatasheetSolenoid valves CPE14 DatasheetSolenoid valves CPE14 DatasheetSolenoid valves CPE14 DatasheetSolenoid valves CPE14 DatasheetSolenoid valves CPE14 Ordering dataSolenoid valves CPE14 Ordering dataManifold blocks CPE14 Datasheet – Manifold blockManifold block CPE...-PRSMaterial:Wrought aluminium alloyRoHS-compliantManifold blocks CPE14Ordering data – Fixed-grid manifold block1)Corrosion resistance class CRC 2 to Festo standard FN 940070Moderate corrosion stress. Indoor applications in which condensation can occur. External visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment.Manifold blocks CPE14 Technical data – Fixed-grid manifold blockManifold blockFor CPE14 3/2Material:Wrought aluminium alloyRoHS-compliantManifold blocks CPE14Ordering data – Fixed-grid manifold block1)Corrosion resistance class CRC 2 to Festo standard FN 940070Moderate corrosion stress. Indoor applications in which condensation can occur. External visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment.Manifold blocks CPE14 Technical data – Modular manifoldModular manifold blockFor CPE14 5/2 and 5/3Material:Reinforced PA1)n = number of valve positionsManifold blocks CPE14Technical data – Modular manifold-NoteH-Each air supply can support a maximum of 6 valve positions. Use valve manifold blocks only in combination with 5/2- and 5/3-way valves.。
0340 3 2-way 电磁阀说明书
0340Type 0340 can be combined with...3/2-way Solenoid Valvefor gases and liquidsThe pilot-controlled 3/2-way solenoid valveType 0340 with smoothly operating servo-piston requires a differential pressure of 7 PSI for complete opening and closing. A diaphragm separates the operating medium from thedrive. It can be used in many ways, even for dry running.Manual override as standard.Circuit function C3/2-way valve, when de-energized outlet port A exhausted, with 3-way pilot controlCircuit function D3/2-way valve, when de-energized outlet port B pressurized, with 3-way pilot controlType 2511 Type 8600Technical dataPort R is one orifice size larger than the ports A/B and P (see Dimensional Table). As a result, the flow A R is increased by the factor 1.5 to 2 over the value in the table.Ordering chart for valves (other versions on request)All valves with manual override, brass body, NBR seal and cable plug■Port R is one orifice size larger than the ports A/B and P (see Dimensional Table). As a result, the flow A ➔R is increased by the factor 1.5 to 2 over the value in the table.* Maximum pressure rating for UL listed valves is 174 PSIFurther versions on requestVoltageNon-standard voltages (012/DC and 110/50) ApprovalsATEX-Ex / UL / UR / CSAMaterialCoil: EpoxySeparating diaphragm: NBR O -ring: NBR Piston ring: PTFE Seat seal: NBR Body:BrassDimensions [mm]A B D H L 46 33 NPT 1/4 154.5 65 46 33 NPT 3/8 179.5 76 46 33 NPT 1/2 179.5 76 62 52 NPT 3/4 215.5 90 8260NPT 1237.5110This dimensional drawing shows a valve in circuit function C with port designations P, R and A/B (see figure on the front page). In circuit function D, the manual override is located above the port connection A/B.In case of special application conditions, We reserve the right to make technical changes without notice. please consult for advice. © Christian Bürkert GmbH & Co. KG0801/3_US-en_1000082397To find your nearest Burkert facility, click on the orange box➞。
电磁阀规格书
档案号PROJECT No: 设计阶段STAGE: 页数PAGE:
版本
FA
REV
其他 Miscell
序号 ITEM No.
附件 Accessories
电磁线圈 Solenoid
阀体 Valve Body
位号 TAG No.
检测位置 SERVICE
介质名称 介质状态 FLUID STATE
操作压力
OPER.PRESS.Mpa(G)
仪表规格书（电磁阀） INSTRUMENT SPECIFICATION (SOLENOID VALVE)
1 型式 Type 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 型号 Model 动作方式 Oper. Style 本体等级 Body Rating 连接型式尺寸 Conn. Size 阀孔径 Size Orifice 流通能力 Cv 最大差压 Dp Max.(MPa) 阀座密封 Sealing Seat/Plug 本体材质 Body Mat'l 阀芯材质 Plug Mat'l 安装位置 Mount Position 环境温度 Ambient Temp.(℃)最低 Min. 最高 Max. 线圈数量 Number of Coil 线圈型式 Type of Coil 失电时阀门位置 De-Energized Position 操作电源/频率 Operating Voltage/Frequeace 绝缘等级 Insulation Class 起动电源消耗 Starting Power Consump 工作电源消耗 Working Power Consump 电气接头 Elect. Conn. 防护等级 Enclosure Protection 防爆等级 Explosion Proof 手动复位 Manual Reset 手操器 Manual Operator 过流保护电路 Prot. Citcuit Extra. Curr. 端子板 Terminal Strip 接线盒 推荐制造商 Manufacturer
A-T Controls, Inc. 电磁阀说明书
D9-3R-20230118Copyright 2013 A-T Controls, Inc.ElectricPneumaticavailable for seat materials. The 50/50 STFE seat option is excellent for services that call for higher temperatures and more difficult applications,including steam. Call us for details.Lock Saddle See automated data sheets for pre-sized assembliesEasy to Automate!Cincinnati, Ohio FAX (513) 247-5462********************1D9C-F1-0300-XXX-_-_ _See part number matrix for itemized optionsHOW TO ORDER MANUAL VALVESSAMPLE PART #Valve SeriesBody Material End ConnectionSeat MaterialValve SizeSpecial Designation Additional Special DesignationHigh Performance, Full Port Split Body Ball ValveSeries D9 (ASME Class 150)2D9-3R-20230118 | Copyright 2013 A-T Controls, Inc. | | (513) 247-5465* FOR 10”=16 PCS OF BOLTS AND BOLT NUTS * FOR 12”=24 PCS OF BOLTS AND BOLT NUTSTHE STANDARD CONFIGURATION, OTHER MATERIALS ARE AVAILABLE UPON REQUESTHigh Performance, Full PortSplit Body Ball ValveSeries D9 (ASME Class 150)38” to 12”D9-3R-20230118 | Copyright 2013 A-T Controls, Inc. | | (513) 247-54654D9-3R-20230118 | Copyright 2013 A-T Controls, Inc. | | (513) 247-5465SERIES D9 150# Flanged Direct MountDIMENSIONS (IN)DIMENSIONS SHOWN ARE FOR ASSEMBLIES SIZED FOR 80 PSI SUPPLY5SAMPLE PART #D9C-F1-150/3RFD-XXSee automated part number matrix on back cover for complete partnumber and options.Carbon Steel Valve SeriesSeat MaterialValve SizeEnd ConnectionTRIAC Actuator SeriesActuator Size Double ActingSUFFIX 1: Solenoids SUFFIX 2: Limit Switch Actuators are sized based on full differential pressure with clean water. Consult the Application Sizing Guide for assistance with sizing actuators.ASME Class 150 FlangedDirect MountD9-3R-20230118 | Copyright 2013 A-T Controls, Inc. | | (513) 247-5465SERIES D9 150# Flanged Direct MountASME Class 150 FlangedDirect MountDIMENSIONS (IN)D9-3R-20230118 | Copyright 2013 A-T Controls, Inc. | | (513) 247-54656SAMPLE PART #D9C-F1-150/3RGS-XXSee automated part number matrix on back cover for complete part number and options.Carbon Steel Valve SeriesSeat MaterialValve SizeEnd ConnectionTRIAC Actuator SeriesActuator Size Spring ReturnSUFFIX 1: Solenoids SUFFIX 2: Limit SwitchActuators are sized based on full differential pressure with clean water. Consult the Application Sizing Guide for assistance with sizing actuators.DIMENSIONS (IN)(D) DIMENSION IS FROM CENTERLINE TO END OF HANDWHEEL ON 2-1/2” – 6” OR MODULATING ACTUATORS 1/2” – 2”.FOR SPECIALS, CONSULT FACTORYD9-3R-20230118 | Copyright 2013 A-T Controls, Inc. | | (513) 247-54657SAMPLE PART #D9C-F1-150/WEA1-XXSee automated partnumber matrix on back cover for complete part number and options.Carbon Steel Valve SeriesSeat MaterialValve SizeEnd ConnectionTRIAC Actuator SeriesActuator SizeOn-Off SUFFIX 1: Voltage SUFFIX 2: OptionsOther options available - call for detailsActuators are sized based on full differential pressure with clean water. Consult the Application Sizing Guide for assistance with sizing actuators.ASME Class 150 FlangedDirect MountSeries D9HOW TO ORDER: Manual ValvesHOW TO ORDER: Automated Valves17-4 PH is a registered trademark of AK Steel Corporation.Chemraz® is a registered trademark of Greene, Tweed & Co.Perlast® is a registered trademark of Precision Polymer Engineering Limited.TFM™ is a trademark of Dyneon™, a 3M Company.D9-3R-20230118Copyright 2013 A-T Controls, Inc.Cincinnati, Ohio FAX (513) 247-5462********************SAMPLE PART #AUTOMATED VALVE (10) Special Designation (2) Valve Series(3) Body/Ball/StemMaterial (6) Valve Size(5) Seat/Trim Material(4) End Connection(7A) TRIAC Actuator Series(7A) Actuator Size (7B) Double Acting (8) Accessory (9) Accessory D9C-F1-150/3R3D-XX-_8**2500 & 3500 60 psig spring。
电磁阀
维修记录
日期
维修内容
维修人
备注
05.10.
开始启用
07.05.07
检修正常
柴宏许治国
08.06.10
检修正常
柴宏许治国
仪表档案卡
名称
电磁阀
规格型号
M15G15DE12PU-T
出厂编号
公称通径
位号
HV-1205B
安装位置
2#发生器
工艺介质
仪表气
压力等级
用途
2#发生器二道排渣阀控制
生产厂
技术参数
M15G15DE12PU-T
备注
维修记录
日期
维修内容
维修人
备注
05.10.
开始启用
07.05.07
检修正常
柴宏许治国
08.06.10
检修正常
柴宏许治国
仪表档案卡
名称
防爆电磁阀门
规格型号
2CSB-25J
出厂编号
公称通径
位号
LSV2-1305B
安装位置
工艺介质
仪表气
压力等级
用途
水环泵B汽水分离器进水控制
生产厂
技术参数
2CSB-25J
规格型号
出厂编号
公称通径
位号
DF-508
安装位置
单体压缩机
工艺介质
仪表气
压力等级
用途
二级排气端集油器液位控制阀
生产厂
技术参数
备注
维修记录
日期
维修内容
维修人
备注
05.10.
开始启用
07.05.07
检修正常
柴宏许治国
08.06.10
2URED6 电磁阀说明书
2
The directional valve type 2URED6… comprises of solenoid (1), sleeve (2), poppet (3) and spring (4). Flow opening or closing is obtained by changing position of the poppet (3) inside the sleeve (2). In version 2URED6C1… in neutral (current-free) position poppet (3) opens the flow. Flow closing occurs by supplying the solenoid (1) with the voltage and moving the poppet (3). Cutting off supply voltage causes return of the poppet (3) to its starting position by means of the
Directional cartridge valve
tight on both sides type 2URED6
NS6
up to 35 MPa up to 25 dm3/min
DATA SHEET - OPERATION MANUAL
WK 493 130
05.2015
APPLICATION
Directional cartridge valve type 2URED6… is intended for control direction of fluid flow, causing particular movement direction or stops a receiver (cylinder or hydraulic motor). The directional valve is mounted by screwing into a threaded cavity. The product is complied with the regulations of directive 2006/95/WE for the following voltages: • 50 – 250 V for AC • 75 – 250 V for DC
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
电磁阀规格书编号：
产品名称：CDF型电磁阀用途：汽车空调系统
编制：
校对：
审核：
批准：
1．适用范围
本规格书适用于本公司生产的以R134a、R410a为制冷剂的汽车空调系统用电磁阀。
2．术语和定义
电磁阀是一种由线圈产生的电磁吸力控制内部芯铁上下活动，开闭阀口，从而控制流通介质通断的执行器件。
3．基本规格
序号项目规格备注
3.1 电源DC24V/DC12V
3.2 电压变化额定电压的90%-110%范围
3.3 最大工作压力
4.2MPa
3.4 额定功率<20W
3.5 阀口公称通径Φ10mm
3.6 适用制冷剂R134A、R410A等
3.7 介质流动方向单向
3.8 安装方式以阀体及线圈的断面中心线为轴，在垂直±15°以内
3.9 适用环境温度-20℃～+55℃
3.10 适用环境湿度95%RH以下
3.11 适用液体温度-30℃～+105℃
4. 环保要求
4.1 阀体外表面要求耐NaCl、H2S等腐蚀；
4.2 所用材料对人体无毒害且不产生有毒物质，符合RoHS要求；
4.3 阀体内部结构材料需满足耐冷媒腐蚀，冲击；
4.4 阀内部材料强度，刚度能满足产品性能要求；
5. 外观构造
5.1 外观、尺寸、构造、材质满足图纸要求。
5.2 外观无明显的伤痕、变形、氧化腐蚀、毛刺等缺陷，线圈引出线及端子完好无损。
5.3 产品由线圈与阀体组成。
5.4 阀体内部不得有切屑、油渍、锈迹等存在。
5.5 包装：接管进、出口端使用防尘帽。
6. 性能测试基本条件如下：
6.1 安装：基本状态竖直安装，线圈安装在阀体上，阀体轴心线倾斜角度控制在15°以内；
6.2 除有特别规定外，基本测试条件如下：
6.2.1 室温（试验品）及流体温度：20±5℃；
6.2.2 相对湿度：65±20%RH，无风；
6.2.3 流动方向：进口管—出口管(单向)；
6.2.4 电源：DC24V/DC12V；
7．测试仪表要求：
测试设备应在有效使用期内，并附有鉴定合格证，其仪表准确度等级应符合下列规定：
①温度测量仪表准确度不低于1.0级；
②压力测量仪表准确度等级不低于1.5级；
③流量测量仪表准确度不低于1.5级；
④电压测量仪表准确度等级不低于1.5级；
⑤拉力测试仪表准确度等级不低于1.0级；
⑥电阻测量仪表准确度不低于0.1级；
8. 试验项目及试验方法：
10. 标志、包装及贮存
10.1 在电磁阀的标签上应标出下列内容：
a．电磁阀型号及名称；
b．额定电压；
c．产品编号或生产日期；
d. 制造厂名及商标；
e. 介质流动方向；
10.2、产品出厂时进、出气管口处应有防尘保护，并应做到清洁、防潮和防霉。
10.3、产品出厂时应随带下列技术文件：
a. 产品合格证；
b. 出厂检验单；
10.4、电磁阀应贮存在清洁、干燥的通风室内，室内空气中不含有腐蚀电磁阀的有害物质。
11. 注意事项
11.1焊接连接管时,阀体温度不应超过200℃。
11.2安装：竖直安装，线圈安装在阀体上，阀体轴心线倾斜角度控制在15°以内。
11.3线圈紧固扭矩2.0±0.5N.m。
12. 其它
本产品规格书上没有记载事项或有任何不适合之处，如有必要时，请供需双方协商解决。