PCB术语中英文对照表 精华版
PCB中英文对照词汇
PCB 中英文对照词汇一、综合词汇序号中文英文1印刷电路Printed circuit2印制线路Printed wiring3印刷板Printed board4印制板电路Printed circuit board(pcb)5印制线路板Printed wiring board(pwb)6印制元件Printed component7印制接点Printed contact8印制板装配Printed board assembly9板board10单面印制板Single-sided printed board(ssb) 11双面印制板Double-sided printed board(dsb) 12多层印制板Multilayer printed board(mlb) 13多层印制电路板Multilayer printed circuit board 14多层印制线路板Multilayer printed wiring board 15刚性印制板Rigid printed board16刚性单面印制板Rigid single-sided printed board 17刚性双面印制板Rigid double-sided printed board 18刚性多层印制板Rigid multilayer printed board 19挠性多层印制板Flexible multilayer printed board20挠性印制板Flexible printed board21挠性单面印制板Flexible single-sided printed board22挠性双面印制板Flexible double-sided printed board23挠性印制电路Flexible printed circuit(fpc)24挠性印制线路Flexible printed wiring25刚性印制线路Flex-rigid printed board 、 rigid-flexprinted board26刚性双面印制板Flex-rigid double-sided printed board、rigid-flex double-sided printed27刚性多层印制板Flex-rigid multilayer printed board、rigid-flex double-sided printed28齐平印制板Flush printed board29金属芯印制板Metal core printed board30金属基印制板Metal base printed board31多重布线印制板Mulit-wiring printed board32陶瓷印制板Ceramic substrate printed board33导电胶印制板Electroconductive paste printed board34模塑电路板Molded circuit board35模压印制板Stamped printed wiring board36顺序层压多层印制板Sequentially-laminated multilayer37散线印制板Discrete wiring board38微线印制板Micro wire board39积层印制板Build-up printed board40积层多层印板Build-up multilayer printed board (bum) 41积层挠性印制板Build-up flexible printed board42表面层合电路板Surface laminar circuit(slc)43埋入凸块连印制板B2it printed board44多层膜基板Mutil-layered film substrate(mfs) 45层间全内导通多层印Alivh multiplayer printed board制板46载芯片板Chip on board (cob)47埋电阻板Buried resistance board48母板Mother board49子板Daughter board50背板backplane51裸板Bare board52键盘板夹心板Copper-invar-copper board53动态挠性板Dynamic flex board54静态挠性板Static flex board55可断拼板Break-away planel56电缆cable57挠性扁平电缆Flexible flat cable (ffc)58薄膜开关Membrance switch59混合开关Hybrid circuit60厚膜Thick film61厚膜电路Thick film circuit62薄膜Thin film63薄膜混合电路Thin film hybrid circuit 64互连interconnection65导线Conductor trace line 66齐平导线Flush conductor 67传输线Transmission line 68跨交crossover69板边插头Edge-board contact 70增强板stiffener71基底Substrate72基板面Real estate73导线面Conductor side74元件面Component side 75焊接面Solder side76印制Printing77网格Grid78图形Pattern79导电图形Conductive pattern 80非导电图形Non-conductive pattern 81字符legend82标志mark二、基材序号中文英文1基材Base material2层压板Laminate3覆金属箔基材Metal-clad bade material4覆铜箔层压板Copper-clad laminate(ccl)5单面覆铜箔层压板Single-sided copper-clad laminate 6双面覆铜箔层压板Double-sided copper laminate 7复合层压板Composite laminate8薄层压板Thin laminate9金属芯覆铜箔层压板Metal core copper-clad laminate 10金属基覆铜层压板Metal base copper-clad laminate 11挠性覆铜箔绝缘薄膜Flexible copper-clad dielectric film 12基体材料Basis material13预浸材料Prepreg14粘结片Bonding sheet15预浸粘结片Preimpregnated bonding sheet 16环氧玻璃基板Epoxy glass substrate17加成法用层压板Laminate for additive process 18预制内层覆箔板Mass laminate panel19内层芯板Core material20催化板材Catalyzed board21涂胶催化层压板Adhesive-coated catalyzed laminate 22涂胶无催化层压板Adhesive-coated uncatalyzed laminate 23粘结层Bonding layer24粘结膜Film adhesive25涂胶粘剂绝缘薄膜Adhesive coated dielectric film26无支撑胶粘剂膜Unsupported adhesive film27覆盖层Cover layer28增强板材Stiffener material29铜箔面Copper-clad surface30去铜箔面Foil removal surface31层压板面Unclad laminate surface32基膜面Base film surface33胶粘剂面Adhesive face34原始光洁面Plate finish35粗面Matt finish36纵向Length wise direction37横向Cross wise direction38剪切板Cut to size panel39酚醛纸质覆铜箔板Phenolic cellulose paper copper-cladlaminates(phenolic paper ccl)40环氧纸质覆铜箔板Epoxide cellulose paper copper-cladlaminates(epoxy paper ccl)41环氧玻璃布基覆铜箔Epoxide woven glass fabric copper-clad 板laminate42环氧玻璃布纸复合覆Epoxide cellulose paper core glass cloth 铜箔板surfaces copper-clad laminate43环氧玻璃布玻璃纤维Epoxide non woven glass reinforced 复合覆铜箔板copper-clad laminate44聚酯玻璃布覆铜箔板Polyester wovenglass fabric copper-clad laminate45聚酰亚胺玻璃布覆铜Polyimide woven glass fabric copper-clad箔板laminate46双马来酰亚胺三嗪环Bismaleimide triazine epoxide woven 氧玻璃布覆铜板glass fabric copper-clad laminate47环氧合成纤维布覆铜Epoxide synthetic fiber copper-clad箔板laminates48聚四乙烯玻璃纤维覆Teflon fiber glass copper-clad laminate铜箔板49超薄型层压板Ultra thin laminate50陶瓷基覆铜箔板Ceramincs base copper-clad laminate 51紫外线阻挡型覆铜箔Uv blocking copper-clad laminates板三、基材的材料序号中文英文1 a 阶树脂a-stage resin2 b 阶树脂b-stage resin3 c 阶树脂c-stage resin4环氧树脂Epoxy resin5酚醛树脂Phenolic resin6聚酯树脂Polyester resin7聚酰亚胺树脂Polyimide resin8双马来酰亚胺三嗪树Bismaleimide-triazine resin脂9丙烯酸树脂Acrylic resin10三聚氰胺甲醛树脂Melamine formaldehyde resin 11多功能环氧树脂Polyfunctional epoxy resin 12溴化环氧树脂Brominated epoxy resin 13环氧酚醛Epoxy novolac14氟树脂fluroresin15硅树脂Silicone resin16硅烷silane17聚合物polymer18无定形聚合物Amorphous polymer19结晶现象Crystalline polamer20双晶现象dimorphism21共聚物copolymer22合成树脂synthetic23热固性树脂Thermosetting resin24热塑性树脂Thermoplastic resin25感光性树脂Photosensitive resin26环氧当量Weight per epoxy equipvalent(wpe) 27环氧值Epoxy value28双氰胺dicyandiamide29粘结剂binder30固化剂Curing agent31胶粘剂adesive32阻燃剂Flame retardant33遮光剂opaquer34增塑剂plasticizers35不饱和聚酯Unsatuiated polyster36聚酯薄膜polyester37聚酰亚胺薄膜Polyimide film(pi)38聚四氟乙烯Polytetrafluoetylene(ptfe)39聚四氟乙烯丙烯薄膜Perfluorinated ethylene-propylenecopolymer film(fep)40增强材料Reinforcing material41玻璃纤维Glass fiber42 E 玻璃纤维e-glass fiber43 D 玻璃纤维d-glass fiber44S 玻璃纤维s-glass fiber45玻璃布Glass fabric46非织布Non-woven fabric 47玻璃纤维垫Glass mats48纱线yarn49单丝filament50胶股strand51纬纱Weft yarn52经纱Warp yarn53但尼尔denier54经向Warp-wise55纬向Weft-wise 、 filling-wise 56织物经纬密度Thread count57织物组织Weave structure58平纹组织Plain structure59坏布Grey fabric60稀松织物Woven scrim61弓纬Bow of weave62断经End missing63缺纬Mis-picks64纬斜bias65折痕crease66云织waviness67鱼眼Fish eye68毛圈长Feather length69厚薄段mark70裂缝spilt71捻度Twist of yarn72浸润剂含量Size content73浸润剂残留量Size residue74处理剂含量Finish leval75浸润剂size76偶联剂Couplint agent77处理织物Finished fabric78聚酰胺纤维Polyarmide fiber79聚酯纤维非织布Non-woven polyester fabric 80浸渍绝缘纵纸Impregenating insulation paper 81聚芳酰胺纤维纸Aromatic polyamide paper 82断裂长Breaking length83吸水高度Height of capillary rise84湿强度保留率Wet strength retention85白度whitenness86陶瓷ceramics87导电箔Conductive foil88铜箔Copper foil89电解铜箔Electrodeposited copper foil (ed copperfoil)90压延铜箔Rolled copper foil91退火铜箔Annealed copper foil92压延退火铜箔Rolled annealed copper foil (ra copperfoil)93薄铜箔Thin copper foil94涂胶铜箔Adhesive coated foil95涂胶脂铜箔Resin coated copper foil(rcc)96复合金属箔Composite metallic material97载体搏Carrier foil98殷瓦invar99箔（剖面）轮廓Foil profile100光面Shiny side101粗糙面Matte side102处理面Treated side103防锈处理Stain proofing104双面处理铜箔Double treated foil四、设计序号中文英文1原理图Shematic diagram2逻辑图Logic diagram3印制线路布设Printed wire layout4布设总图Master drawing5可制造性设计Design-for-manufacturability6计算机辅助设计Computer-aided design(cad)7计算机辅助制造Computer-aided manufacturability(cim) 8计算机集成制造Computer integrat manufacturing 9计算机辅助工程Computer-aided engineering(cae) 10计算机辅助测试Computer-aided test (cat)11电子设计自动化Electric design automaton(eda) 12工程设计自动化Engineering design automaton(eda2) 13组装设计自动化Assemnly aided architecturaldesign(aaad) 14计算机辅助制图Computer aided drawing15计算机控制显示Computer controlled display(ccd) 16布局placement17布线routing18布图设计layout19重布rerouting20模拟simulation21逻辑模拟Logic simulation22电路模拟Circit simulate23时序模拟Timing simulation24模块化modularization25布线完成率Layout effeciency26机器描述格式Machine descriptionm format(mdf) 27机器描述格式数据库Mdf database28设计数据库Design database29设计原点Design origin30优化（设计）Optimization(design)31供设计优化坐标轴Predominant axis32表格原点Table origin33镜像Mirroring34驱动文件Drive file35中间文件Intermediate file36制造文件Manufacturing documentation 37队列支撑数据库Queue support database38元件安置component positioning 39图形显示Graphics display40比例因子Scaling factor41扫描填充Scan filling42矩形填充Rectangle filling43填充域Region filling44实体设计Physical design45逻辑设计Logic design46逻辑电路Logic design47层次设计Hierarchical design48自顶向下设计Top-down design49自顶向上设计Bottom-up design50线网net51数字化digitzing52设计规则检查Design rule checking53走（布）线路Router(cad)54网络表Net list55计算机辅助电路分析Computer-aided circuit analysis 56子线网Subnet57目标函数Objective function58设计后处理Post design processing(pdp) 59交互式制图设计Interactive drawing design 60费用矩阵Cost metrix61工程图Engineering drawing62方块框图Block diagram63迷宫Moze64元件密度Component density65巡回售货员问题Traveling salesman problem 66自由度Degrees freedom67入度Out going degree68出度Incoming degree69曼哈顿距离Manhatton distance70欧几里德距离Euclidean distance71网络Network72阵列Array73段Segment74逻辑Logic75逻辑设计自动化Logic design automation 76分线Separated time77分层Separated layer78定顺序Definite sequence79对准度registration80孔环Annular ring81公差Tolerance82同心Concentricity83样片coupon84变色discolorations85污点Stains86试样Specimen 87钻孔Drilling88剪裁Shearing 89切外型Routing90刮线Scoring91倒角Chamfering 92切空Blanking 93适应性suitability 94板弯Bow95板扭Twist96应力Stress97防焊膜Solder mask 98阻焊膜Solder resist 99文字标记Legend 100版本代字Revision letter 101料号Part No 102跳漏Skipping 103浮空Soda strawing 104流动Flow 105整平Leveling 106FPR First pass yield ‘。
中英对照PCB专业术语精选全文
analog circuit
模拟电路
amplitude
电压幅度
amp-hour
安培小时
amperometric titration
电流滴定
ampere
安{培)
amorphous thin film
非晶薄膜
amorphous thin film
非晶薄膜
amorphous semiconductor material
单向导电膜安装，各向异性导电膜连接
anisotropic conductive contact
单向导电接触，各向异性导电接触
anisotropic conductive adhesives
单向导电黏结剂，各向异性导电黏结剂
angstrom unit
埃单位
angle rotor
角转头
angle of contact
烷基咪唑
alkaline permanganate solution
碱性高锰酸盐溶液
alkaline etchant
碱性蚀刻液
alkaline degreasing
化学除油
alkaline cleaner
破性清洗液
alkaline ammonia etchant
氨碱蚀刻液
ALIVH
任意层内导通孔
aliphatic solvent
adhesion promotion
增教处理，附着力增强
by-product
副产品，副产物
butt lead
搭接引线，对接引线
butting connector
对接引脚
butter coat
厚涂层，外表树脂层
PCB术语中英文对照
(Discrete Board) ——复线板，是指用极细的漆包线直接在无铜的板面上进行立体交叉的布线，在用胶固定及钻孔与镀孔后，得到多层互连的线路板，是美国PCK公司所开发。
这种MWB可节约设计时间，适用于复杂线路的少量机种。
Nail Heading ——钉头，由于钻孔的原因导致多层板的孔壁的内层线路张开。
Negative Etchbak ——内层铜箔向内凹陷。
Negative Pattern ——负片，在生产或客户菲林上，图像被制作成透明而其它的地方被制作成非透明。
Nick ——线路边的切口或缺口。
Nodle ——从表面突起的大的或小的块。
Nominal Cured Thickness ——多层板的厚度，或者多层板相邻层与层之间固化后的厚度。
Nonwetting——敷锡导致导体的表面露出。
Overlap ——钻尖点分离，正常的钻尖是有两个第一面和两个第二面，是长刃及凿刃为棱线组成金字塔形的四面共点，此单一点称为钻尖点，当翻磨不良时，可能会出现两个钻尖点，对刺入的定位不利，是钻咀的大缺点。
Pink ring ——粉红圈,由于内层铜的黑氧化层被化学处理掉，而导致在环绕电镀孔的内层出现粉红色的环状区域。
Plated ——在多层板的压合过程中，一种可以活动升降的平台。
Point ——是指钻头的尖部。
Point Angle ——钻尖角，是指钻咀的钻尖上，有两条棱线状的长刃所构成的夹角，称为“钻尖角”。
Polarizing Slot ——偏槽，见“Keying Slot”。
Porosity Test ——孔隙率测试，是对镀金层所做的试验。
Press－Fit Contact——指某些插孔式的镀金插脚，为了以后抽换方便便常不施以填焊连接，而是在孔径的严格控制下，是插入的接脚能做紧迫式的接触。
Press Plate ——钢板，用于多层板的压合。
Rack ——挂架，是板子在进行电镀或其它湿流程处理时，在溶液中用以临时固定板子的夹具。
PCB专业用语中英文对照
PCB专业用语中英文对照PCB，全称是Printed Circuit Board，即印制电路板，是电子器件中不可缺少的一部分。
在PCB的生产和使用过程中，有许多特定的专业术语，以下将列出一些常见的PCB专业用语的中英文对照，以帮助PCB行业的从业人员更好地了解和使用这些术语。
1. Pad - 表面贴装元件引脚焊盘2. Via - 通孔3. Trace - 线路走线4. Solder mask - 焊盘阻焊5. Silkscreen - 字体绘制6. Substrate - 基板7. RoHS - 过度有害物质限制指令8. PCB Assembly - PCB组装9. Panel - 夹板10. Gerber file - Gerber文件（PCB板图文件的一种）11. Copper weight - 铜箔厚度12. SMD - 表面贴装元件13. Through-hole - 贯通孔除此之外，还有一些专业用语需要注意：1. Blind via - 盲孔2. Buried via - 埋孔3. Soldering - 焊接4. Copper pour - 铜泡5. Annular ring - 环形垫片6. Plated through-hole - 化学镀铜孔7. Gold finger - 金手指（PCB板边部的带触点金属部件）8. OSP - 有机锡防护（一种PCB表面处理方法）以上仅列举了部分PCB专业用语的中英文对照，如需更全面的了解，需要从事相关行业或有专业经验的人士掌握更多知识。
在PCB制造和使用过程中，正确使用这些专业用语是非常重要的，它们不仅可以帮助我们更好地了解PCB的生产过程和使用方法，还可以提高工作效率和避免出现误解和错误。
PCB行业最常用术语之中英文对照
PCB行业最常用术语之中英文对照(按字母检索)A/W (artwork) 底片Ablation 烧溶(laser),切除abrade 粗化abrasion resistance 耐磨性absorption 吸收ACC ( accept ) 允收accelerated corrosion test 加速腐蚀accelerated test 加速试验acceleration 速化反应accelerator 加速剂acceptable 允收activator 活化液active work in process 实际在制品adhesion 附着力adhesive method 黏着法air inclusion 气泡air knife 风刀amorphous change 不定形的改变amount 总量amylnitrite 硝基戊烷analyzer 分析仪anneal 回火annular ring 环状垫圈;孔环anode slime (sludge) 阳极泥anodizing 阳极处理AOI ( automatic optical inspection ) 自动:光学检测applicable documents 引用之文件AQL sampling 允收水准抽样aqueous photoresist 液态光阻aspect ratio 纵横比(厚宽比)As received 到货时back lighting 背光back-up 垫板banked work in process 预留在制品base material 基材baseline performance 基准绩效batch 批beta backscattering 贝他射线照射法beveling 切斜边;斜边biaxial deformation 二方向之变形black-oxide 黑化blank controller 空白对照组blank panel 空板blanking 挖空blip 弹开blister 气泡;起泡blistering 气泡blow hole 吹孔board-thickness error 板厚错误bonding plies 黏结层bow ; bowing 板弯break out 从平环内破出bridging 搭桥;桥接BTO (Build To Order) 接单生产burning 烧焦burr 毛边(毛头)camcorder 一体型摄录放机carbide 碳化物carlson pin 定位梢carrier 载运剂catalyzing 催化catholic sputtering 阴极溅射法caul plate 隔板;钢板calibration system requirements 校验系统之各种要求center beam method 中心光束法central projection 集中式投射线certification 认证chamfer 倒角(金手指)chamfering 切斜边;倒角characteristic impedance 特性阻抗charge transfer overpotential 电量传递过电压chase 网框checkboard 棋盘chelator 蟹和剂chemical bond 化学键chemical vapor deposition 化学蒸着镀circumferential void 圆周性之孔破clad metal 包夹金属clean room 无尘室clearance 间隙coat 镀外表coating error 防焊覆盖错误coefficient of thermal expansion (CTE) 热澎胀系数cold solder joint 冷焊点cold-weld 金属粉末冷焊color 颜色color error 颜色错误compensation 补偿competitive performance 竞争力绩效complex salt 错化物complexor 错化物component hole 零件孔component side 零件面concentric 同心conformance 密贴性consumer products 消费性产品contact resistance 接触电阻continuous performance 连续发挥效能contract service 协力厂controlled split 均裂式conventional flow 乱流方式conventional tensile test 传统张力测试法conversion coating 转化层convex 突出coordinate list 数据清单copper claded laminates (CCL) 铜箔基板copper exposure 线路露铜copper mirror 镜铜copper pad 铜箔圆配copper residue (copper splash) 铜渣corrosion rate numbering 腐蚀速率计数系统corrosion resistance 抗蚀性coulombs law 库伦定律countersink 喇叭孔coupon 试样coupon location 试样点covering power 遮盖力CPU 中央处理器crack 破裂;裂痕crazing 裂痕;白斑cross linking 交联聚合cross talk 呼应作用crosslinking 交联crystal collection 结晶收集curing 聚合体current efficiency 电流效率cut-outs 挖空cutting 裁板cyanide 氰化物cycles of learning 学习循环cycle-time reduction 交期缩短date code 周期deburring 去毛头dedicated 专用型degradation 退变delamination 分层dent / pin hole 凹陷/ 针孔department of defense 国防部designation 字码简示法de-smear 除胶渣developing 显影dewetting 缩锡dewetting time 缩锡时间dimension error 外形尺寸错误dielectric constant 介质常数difficulty 困难度difunctional 双功能dimension 尺寸dimension stability 尺寸安定性dimensional stability 尺度安定性dimension and tolerance 尺寸与公差dirty hole 孔内异物discolor hole 孔黑;孔灰;氧化discoloration 变色disposable eyelet method 消耗性铆钉法distortion factor 尺寸变形函数double side 双面板downtime 停机时间drill 钻孔drill bit 钻头drill facet 钻尖切萷面drill pointer 钻尖重(研)磨机drilled blank board 已钻孔之裸板drilling 钻孔dry film 干膜ductility 延展性economy of scale 经济规模edge spacing 板边空地edge-board contact ( gold finger ) 金手指efficiency 能量效率electric test 电测electrical testing 电测;测试electrochemical machine ECM 电化学加工法electrochemical reactor 电化学反应器electroforming 电铸electroless plate 化学铜electroless-deposition 无电镀electropolishing 电解拋光electrorefining 电解精炼electrowinning 电解萃取elliptical set 椭圆形embrittlement 脆性entitlement performance 可达成绩效entrapment 电镀夹杂物epoxy 环氧树酯equipotential 电位线error data file 异常情形etch rate 蚀铜速率etchants 蚀刻液etchback 回蚀evaluation program 评估用程序exposure 曝光external pin method 外部插梢法eyelet hole 铆钉孔Eyeletting 铆眼fabric 网布failure 故障fast response 快速响应fault 瑕庛;缺陷fiber exposure 纤维显露fiber protrusion 纤维突出fiducial mark 光学点,基准记号filler 填充料film 底片filtration 过滤finished board 成品fixing 固着fixture 电测夹具(治具)flaking off 粹离flammability rating 燃性等级flare 喇叭形孔flat cable 并排电缆feedback loop 回馈循环first-in-first-out (FIFO) 先进先出flexible manufacturing system (FMS) 弹性制造系统flux 助焊剂foil distortion 铜层变形fold 空泡foreign include 异物foreign material 基材内异物free radical chain polymerization 自由基连锁聚合fully additive 加成法fully annealed type 彻底回火轫化之类形function 函数fundamental and basic 基本fungus resistance 抗霉性funnel flange 喇叭形折翼galvanized 加法尼化制程gap 钻尖分开gauge length 有效长度gel time 胶化时间general resist ink 一般阻剂油墨general 通论general industrial 一般性(电子)工业级geometrical levelling 几何平整glass transition temperature (Tg) 玻璃态转换温度Gold 金gold finger 金手指gold plating 镀金golden board 标准板gouges 刷磨凹沟gouging 挖破grain boundary 金属晶体之四边green 绿色grip 夹头ground plane 接地层ground plane clearance 接地空环hackers 骇客HAL ( hot air leveling ) 喷锡haloing 白边;白圈hardener 硬化剂hardness 硬度hepa filter 空气滤清器high performance industrial 高性能(电子)工业级high reliability 高可靠度high resolution 高分辨率high temperature elongation (HTE) 高温延展性铜箔high temperature epoxy (HTE) 高温树酯hit 击hole counter 数孔机hole diameter 孔径hole diameter error 孔径错误hole location 孔位hole number 孔数hole wall quality 孔壁品质hook 外弧hot dip 热浸法hull cell 哈氏槽hybrid 混成集成电路hydrogen bonding 氢键hydrolysis 水解hydrometallurgy 湿法冶金法image analysis system 影像分析系统image transfer 影像转移immersion gold 浸金(化镍金) immersion plating 浸镀法impedance 阻抗infrared reflow 红外线重熔inhibitor 热聚合抑制剂injection mold 射模ink 油墨innerlayer & outlayer 内外层insulation resistance 绝缘电阻intended position 应该在的位置intensifier 增强器intensity 强度inter molecular exchange 交互改变interconnection 互相连通ionic contaminants 离子性污染物ionic contamination testing 离子污染试验IPA 异丙醇5I : inspiration (启蒙)identification 确认计划目标implementation 改善方案information 数据internalization 制度化invisible inventory 无形的库存knife edges 刀缘Knoop 努普(硬度单位)kraft paper 牛皮纸laminar flow 层流laminate 基层板laminating 压合lamination 压合laminator 压膜机land 焊垫lay back 刃角磨损lay up 组合叠板layout 布线;布局lead screw 牵引螺丝leakage 漏电learning curve 学习曲线legend 文字标记leveling 平整levelling additive 平整剂levelling power 平整力life support 维系生命limiting current 极限电流line space 线距line width 线宽linear variable differential transformer(LVDL) 线性可变差动:转换器liquid 液状(态)liquid crystal resins 液晶树脂liquid photoimageable solder resist ink 液态感光防焊油墨liquid photoresist ink 液态光阻剂油墨lot size 批量lower carrier 底部承载板mechanical plating 机祴镀法machine scrub 刷磨清洁法macrothrowing power 巨分布力margin 钻头刃带market share 市场占有率marking error 文字错误masked leveling 儰装平整mass lamination 大型压板mass transfer 质量传送效应mass transfer overpotential 质量传递过电压mass transportation 质传master drawing 主图;蓝图material use factor 材料使用率mealing 泡点;白点memory 记忆装置meniscograph solderability measurement 新月型焊锡效果microetch 微蚀microetching 微蚀microfocus 微焦距microfocus system 微焦距系统microprofile 微表面microsectioning 微切片法microthrowing power 微分布力migration 迁移mini-tensile tester 迷你拉力测试仪mis hole location 孔位错误misregistration 焊锡面与零件面对位偏差misregsitration 对不准moisture and insulation resistance test 湿气与绝缘电阻试验molded circuit board (MCB) 模制电路板monoethanal amine 单乙醇氨monohydrate state 水化物monomer 单分子膜;单体mouse bite 锯齿;蚀刻缺口msec 毫秒muffle furnace 高温焚火炉multichip 超大IC型(多芯片模块)mylar 保护膜nail head 钉头NC drill 数字钻孔机negative etchback 反回蚀negative film 负片negative rake angle 负抠耙角network 回路;网络neutralization 中和nick 缺口nickel 镍nodule 铜瘤;瘤粒no flow resin 不流树脂noise 噪声nominal 标示nominal dimension 标定长度nominal gel time 标示胶性时间nominal resin content 标示胶含量nominal resin flow 标示胶流量nominal scaled flow thickness 标示比例流量厚度OA equip 办公室自动:化设备obsolescence factor 报废因素OEM 原设备制造商offset-list 补偿数据清单ohmmeter 欧姆计open 断路open circuits 断路open short testing 断短路测试opening 开口original art work (A/W) 原稿底片Others 其它outgrowth 增出over design 牛刀杀鸡overlap 钻尖重叠overlay entry 盖板overpotential 过电压oxidation 氧化oxide treatment 黑化处理oxided cytochrome 氧化性之细包色素oxygen evolution 氧气发生反应packed bed 充填床式pad 锡垫;圆配pad copper exposure pad露铜panel 小型板面;母板panel plating 一次铜电镀parasitic 寄生的part no. 料号pattern plating 二次铜电镀PCB ( print circuit board ) 印刷电路板pcs 片peel strength 抗撕强度peeling off 剥离(剥落) performance specification 性能规范permittivity 透电率perspectives on experience 经验透视PET 聚酯photodiode detector 发光二极管侦测器photo initiator 感光启始剂photoresist 光阻phototool 光具(指工作底片)piece 子板面pinceton applied research 腐蚀测定仪pink ring 粉红圈pit 凹点pitch 脚距planar 平面plating 电镀plating exposure 下镀层露出plug gauge 插规plug hole 孔塞PNL (panel) 排板polar-polar interaction 极性之间的吸力polyester 聚酯类polyglycols 聚乙二醇polyimide 聚亚醯氨poor bevelling 磨边加工引起突起,剥离poor drill 孔形不良poor HAL 喷锡不良poor marking 字体不良poor pad 锡垫不良poor printed 印刷偏差poor solderability 焊锡性不良poor touch-up 补线不良position control system 位置控制系统positive rake angle 正抠耙角power curve model 幕次曲线模式practice 工艺惯例preferred 良好premature tearing 提前撕裂prepolymer 预聚合物prepreg 胶片pre-process ( front-end) 制前press 压床press cycle 压合周期primary current distribution 一次电流分布primary 主要product lifetimes 生命周期product process 制程promoter 促进剂protocal 初步资料prussic acid 普鲁士酸PTF-based process 厚膜糊法PTH (plating though hole) 导通孔pull away 拉开pumice 浮石粉pumice scrub 喷砂清洁法pyrometallurgy 火烧法冶炼QC ( quality control) 品管QFP (quad flat pack ) 扁方型封装体qualification inspection 资格审查检验qualification testing 资格检定quality classification 品质等级quantitative 计量式测试rack 挂架radiometer 能量剂rake angle 抠耙角RAM [Random Access Memory 随机存取内存real time 关键时刻recessed trace process 凹槽线路法recovery tank 回收槽reduction 还原re-eninforcement 强化refraction 折光率reinforcement style 补强材料的型式register mark 对位用标记registration hole 对位孔registration pattern 长方形铜地REJ ( reject ) 退货;拒收rejectable 拒收release agent 脱模剂relief angle 浮离角remark 备注repair 修理resin content 树脂含量(胶含量)resin flow 胶流量resin flow percentage 树脂流量之百分率resin recession 树脂下陷resin smear 胶渣resist strippers 剥干膜剂resistor network 排列电阻resolution 解像度return on assets 资产报酬率reversibility 可逆性rework 重工rosin 天然松香rotating cylinder 旋转圆柱形roughtness 孔壁粗糙;粗慥routing 切外形,成型routing bit 铣刀runout 偏转S/L on hole 孔内沾文字S/M ( solder mask ), S/L 防焊文字S/M (solder mask) 防焊S/M error 防焊种类错误S/M on hole 孔内绿漆salt spray test 盐水喷雾试验sampling size 抽样数scope 范围scored 刻痕scoring 枢槽;刮线scrap 废框scratches 刮伤screen printing 网版印刷scum 透明残膜sealing 封孔处理secondary 次要semi-additive 半加成法sensitize 敏化sensitizer 敏化液separator 钢隔板sequential lamination 渐成式压法serrated edges 毛边shatter 破碎short 短路shunt 分路silane treatment 硅烷处理silicone coupling agent 硅烷偶合剂silk screen 文字印刷simulator 仿真器single axis 单轴sizing 底片之伸缩补偿skip 漏印skip printing 跳印;漏印sliver 丝条slot 开槽slotting 开槽SMD ( surface mount device ) 表面黏着组件smear 胶渣SMT ( surface mount technology )表面黏着技术sodium carbonate monohydrate 结晶水碳酸钠soft tooling 软性工具solder 焊锡; 锡铅solder bridge 锡桥solder bump 锡突solder float 漂锡solder mask adhesion 绿漆附着力solder on G/F 金手指沾锡solder on trace 线路沾锡solder plug 锡塞solder side 焊锡面solderability 焊锡性solid carbide 实质碳化物spacing 间距spacing nonenough 间距不足SPC ( Statistical Process Control ) 统计生管specification 规范special considerations 特别考虑spin coating 旋转涂布spindle 钻轴spiral contractometer 螺旋收缩仪spot face 铣靶spray coating 喷涂Squeegee 刮刀stacking structure 叠板结构stamping 冲压standard hydraulic lamination标准液压法standardizing 标准化starvation 缺胶step tablet 格片数stock option 认股选择权strain 应度strength 强度stressmeter 应力计subtractive 减除法surface convex 表面突起surface examination 表面检查surface insulation resistance (SIR) 表面绝缘电阻surface mount 表面黏着方式surface roughness 表面粗慥度surges 突波switch circuit 开关线路tab 金手指tack free 不黏taped hole gauge 锥形孔规target hole 靶孔task force 任务编组tensile strength 抗拉强度tensile stress 张性应力tent 浮盖terms and definitions 术语与定义termination load 抗匹配负载test circuit 测试线路test method 试验方法test point 测试点thermal shock 热震荡试验thermal stress 热应力试验thermistor 热电感应式thermo cycling 热循环试验theoretical cycle time 理论性周期时间thickness 厚度time to market 上市时机thickness distribution 厚度分布thief 补助阴极thin core 薄基板;内层板throwing power 分布力tolerance 公差;容差tooling hole 工具孔torque load 扭力拒之负载total quality program 全面的品质计划toughness 坚度trace error 线路错误trace nick & pin hole 线路缺口及针孔trace peeling 线路剥离trace pin-hole 线路针孔trace surface roughness 线路表面粗糙tarnish and oxide resist 抗污抗氧化剂transmittance 透光度trim line 裁切线true levelling 真平整true position 真正位置的孔;真位twist 板翘type 种类umbra 本影undercut 侧蚀uneven coating 喷锡厚镀不平整universal 万用型universal tensile tester 万用拉力试验机universal tester 泛用型测试机upper carrier 顶部承载钢uptime 稼动:时间vacuum deposition 真空蒸镀法vacuum hydraulic lamination真空液压法vaporizer 气化室V-cut V形槽vertical microsection 垂直微切片via hole 导通孔visible inventory 有形的库存vision inspection 目视检查V oid 孔破void in hole 孔壁上的破洞void in PTH hole 孔破walkman 随身听warehouse 仓库warp 板弯warp , warpage 板弯water absorption 吸水性wear resistance 耐磨度weave exposure 纤纹显露weave texture 织纹隐现wedge angle 契尖角week 周wet chemistry 湿式化学制程wet film 湿膜wet lamination 湿膜压膜法wet process 湿制程wetting 沾锡wetting balance 沾锡平衡法wicking 渗铜;渗入;灯蕊效应width 宽度width reduce 线细width-to-thickness ratio 宽度与厚度的比值window 操作范围work-in-process 在制品work order 工单working film 工作片working master 工作母片year 年yellow 金黄色yield 良率。
PCB术语中英文对照表
PCB术语中英文对照表Adｈesiｏn 附着力Annｕｌaｒ Rｉｎg 孔环AOI(aｕtomａtic oｐtｉcal insｐecｔiｏｎ) 自动光学检测AQL(ａccｅptable ｑｕaliｔｙｌｅvel）可接受得质量等级B＆sup2；iｔ(burieｄ bump inｔｅrｃｏnnｅction technolog ｙ）埋入凸块焊点互连技术BBH（bｕriｅd blｉnd ｈoｌｅ）埋盲孔BGA（baｌl grｉｄａrrａy) 球栅阵列Bｌisｔeｒ起泡Boaｒｄ Eｄges 板边Buｒr 毛头/毛刺BＵM（Build—up mｕltｉlayer）积层式多层板BＶH（burieｄ/ｂlinｄ vｉa hoｌe）埋/盲导通孔CAD（puter ａided dｅsign) 计算机辅助设计CAM(puter aided mａnｕfａcturing）计算机辅助制造Ｃａrｂｏｎ oil 碳油CEM(posiｔe ｅpoｘy mａｔｅrｉal）环氧树脂复合板材chaｍfeｒ倒角Characｔeｒistic ｉmpeｄanｃe 特性阻抗CNC(puteriｚed ｎｕmerｉcaｌｃｏnｔroｌ)计算机化数字控制Ｃonductor Ｃrack 导体破裂Condｕctor Spacing 导线间距ｃｏnｎector 连接器Ｃｏｐper fｏil 铜箔(皮）Cｒａziｎｇ微裂纹（白斑）Dｅlaminatiｏn 分层Ｄｅweｔting 半润湿(缩锡）DＦＭ（desｉgn for manuｆacturing）可制造性设计DIP（dｕａl ｉn-ｌine pａcｋagｅ）双列直插式组件Dk（ｄielｅcｔriｃ cｏnｓtａnｔ)介电常数DRC（ｄesign rule ｃhecking) 设计规则检查drａwing 图纸ECN(engineering change nｏtｉce）工程更改通知ECO(enｇineｅｒinｇ changｅｏｒder）工程更改指令E ｇlass 电子级玻璃entek OSP处理Eｐoxy rｅsiｎ环氧树脂ESＤ（eｌeｃtrostaｔiｃ disｃharｇｅ）静电释放Etched Maｒｋing 蚀刻标记Flａｔness 翘曲度Foreiｇｎ Iｎｃlusioｎ外来夹杂物Flame rｅｓiｓtant 阻燃性FR—2（fｌame—ｒetardａnt 2)耐燃酚醛纸基板FR—3(flame－rｅtardant ３）耐燃环氧纸基板FR—4（flame－retａｒdant 4）耐燃环氧玻璃布基板FＲ—５（fｌame-retaｒdanｔ 5）耐燃多功能环氧玻璃布基板ground 地面（层)Haｌｏｉng 晕圈ＨDI(high deｎsitｙ inteｒconneｃｔion）高密度互连技术HAＳL(hot air solｄｅr levelｉng）热风焊料整平（整平）ＩC（inｔeｇraｔｅｄ cｉrcuiｔｓ) 集成电路Ｉnk Stamped Maｒkｉnｇ盖印标记Insulatｉon ｒｅsistancｅ绝缘电阻Ｉon ｃｌeanlineｓs 离子清洁度IPＣ（ｔhe inｓtitutｅfor ｉnｔｅｒconnecting and pａｃkagiｎg of ｅlectrｏnｉc circｕiｔｓ）印制电路互连与封装协会IＳO（Ｉnｔernatiｏｎal ｏrgａnizatｉon ｆor standardization）国际标准化组织Lamiｎａte Vｏidｓ压合空洞ｌａｓer 激光LDI（laser direｃt ｉmaging) 激光直接成像ｌｅｇend 文字标记、符号Ｌｉfｔｅd Lａnds 焊盘浮起logｏ标志LPI（liquiｄｐhotoimａgeablｅ）液态感光成像LPISM(liquｉd phｏｔoimageable soldｅr mask）液态感光阻焊膜mａrkiｎｇ标记Ｍeaｓliｎg 白斑Mｉcrovoids 微坑mil 密耳（千分之一英寸）MIL-ＳTＤ(mｉliｔaｒy ｓtandard）美国军用标准Negatｉｖe Eｔchback 欠蚀Nｉckｓ缺口Noｄuｌes 镀镏Nonｗetting 不润湿(拒锡)open 开路OSP（organic soｌdeｒabilｉty prｅservaｔives) 表面抗氧化ｏxｉｄes 氧化物paｄ焊盘paｎel 拼板pattern 板面图形PCＢ（printeｄ cｉｒcuit ｂｏard) 印制电路板Pcs(piｅｃｅｓ）件、片、只Peeling 剥落pｉnｈole 针孔Pｉnk Rｉng 粉红圈Pits 凹坑pｉtｃh 中心距Pｌａting Ｖoｉdｓ镀层破洞plug 塞Positｉve Eｔｃhback 过蚀power 电源层preｐｒeｇ半固化片PTFE（polytetrａfｌuorｏetｈyｌene) 聚四氟乙烯PTH(plａtｅd through－ｈoｌe）金属化孔PWB（prｉntｅｄ-ｗiriｎg boarｄ) 印制线路板Ｒegisｔration 对准QA（quality ａsｓuranｃｅ）质量保证ＱＣ（qｕaｌity ｃontrol）质量控制QE（qualitｙ engineｅriｎg）质量工程QFP（quad flａt ｐacｋagｅ）方形扁平组件reｐaiｒ修理RCC(ｒｅｓin ｃｏated ｃoppeｒ) 已涂覆树脂得铜箔Refeｒence diｍensｉｏn 参考尺寸ｒegistration 对准度rｅsin 树脂rejectｉon 拒收reviｓioｎ修订版ＲF(rａdｉo frequencｙ）射频Rｉｐples 纹路ｒｏut 外形铣scratch 划伤Screeｎｅd Ｍarkｉnｇ纲印标记scoriｎg 刻槽short 短路sｉgｎal 信号Sｉｌk scrｅen 丝网Skip Coveraｇe 漏印sｌot 开槽SMD（suｒface moｕnt deviｃe）表面安装器件SMＯBC（solder maｓk ｏｖer bare cｏpｐeｒ）裸铜覆盖阻焊膜SMT(suｒfａce ｍount tecｈnologｙ) 表面安装技术smｅaｒ毛刺solder 焊锡Ｓ/Ｍ（solder ｍask）绿油ｓoldｅｒaｂiｌｉty 可焊性Soda Ｓtrawinｇ (汽水)吸管式浮空ＳPC(sｔａtiｓｔicaｌｐrocｅsｓｃontrol) 统计过程控制sｐacing 间距Ｔape ｔest 胶带实验ＴCE（tｈermal coeｆficiｅnt ｏf eｘpａnsiｏｎ）热胀系数TＤR(tｉme-dｏmａｉn refｌｅctometｒｙ)时域反射测试tolｅrancｅ公差Tentｉnｇ盖孔ＴeｘturｅＣoｎdiｔｉon 显布纹Ｔg(glａsｓ tｒaｎsiｔion teｍpeｒaｔｕrｅ) 玻璃软化温度THT （ｔｈｒough hoｌe tｅｃhnｏｌｏgy）通孔（插装)技术ｔrace 线路(条）UL（underｗriteｒs laboratｏries) 安全实验所NPTH 非金属化孔ＵV（ultrａviolet）紫外线辐射v－ｃut V刻Vｉa ｈolｅ导通孔(过线孔)vｏid 空洞wａrp 板弯Waｖes 波浪Wｅａve Exposurｅ露织物ｗetting 沾锡Wiｃking 灯芯效应（渗铜)Wｒｉnｋles 起皱五、形状与尺寸:１、导线（通道）:ｃoｎｄucｔion （tracｋ)2、导线(体）宽度：conduｃtｏr widｔｈ3、导线距离:conductｏr ｓpacｉng４、导线层:conductor layｅｒ5、导线宽度／间距：cｏnductor lｉｎe/sｐａce6、第一导线层:conductor layer no、1７、圆形盘：rouｎd pad８、方形盘:squaｒｅｐad9、菱形盘:diａｍond pad10、长方形焊盘:ｒeｃtanglｅｐad11、子弹形盘：bulｌet ｐaｄ12、泪滴盘:teａrdrop pａd１3、雪人盘：snowmaｎ pａd１4、 v形盘：ｖ-shaped pad１5、环形盘：ａnnulａr paｄ16、非圆形盘:ｎon－ｃirｃular ｐａd１７、隔离盘:isolation pad1８、非功能连接盘:ｍonfｕｎcｔｉonａｌ pａd １９、偏置连接盘:offｓeｔｌaｎd20、腹(背)裸盘：bacｋ—bａrd ｌaｎd２1、盘址：ａnchorｉng spaur22、连接盘图形：lａnd ｐattｅrn2３、连接盘网格阵列:lａnd griｄ array2４、孔环:ａnｎulａr ring2５、元件孔：ponent hｏle２6、安装孔:mountinｇ hole2７、支撑孔：ｓuｐported holｅ28、非支撑孔：unsuppｏrｔed hole29、导通孔：viａ3０、镀通孔:plａted thrｏｕｇh hole （ptｈ）３1、余隙孔：aｃcesｓｈolｅ32、盲孔:blind ｖｉa （ｈolｅ）３３、埋孔:ｂuｒiｅd via hｏle34、埋/盲孔：ｂurｉeｄ /ｂlinｄ via35、任意层内部导通孔：any layeｒ inｎｅr via hole (ａlｉvh）３６、全部钻孔：aｌl drilled holｅ3７、定位孔：toaｌinｇ hｏlｅ38、无连接盘孔:landless ｈole39、中间孔:interstitｉａｌ hole40、无连接盘导通孔：landlｅss via hoｌe41、引导孔:ｐiｌoｔ hole４2、端接全隙孔：ｔerｍinal clearomｅe holｅ４3、准表面间镀覆孔：quａｓｉ-interfａｃing plated—throｕgｈ hｏle 4４、准尺寸孔：ｄimensｉoneｄ holｅ45、在连接盘中导通孔：ｖia－in-pad46、孔位：hoｌe loｃatioｎ47、孔密度:hoｌｅ densitｙ４8、孔图：holｅ pａttern49、钻孔图：driｌl drａwing50、装配图：asｓembly drawing５1、印制板组装图:priｎted boａrd aｓsｅmｂly drａwｉng 5２、参考基准：dａtuｍ reｆeｒaｎｃe。
PCB词汇中英文对照
1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (CCL)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates (phenolic/paperCCL)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paperCCL)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfacescopper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：UV blocking copper-clad laminates<BR< p>。
PCB专业用语 中英文对照
一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board(pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit(fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board,rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board,rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board,rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board(bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit(slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board(cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable(ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate(ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer(cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core,glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent(wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film(pi)38、聚四氟乙烯：polytetrafluoetylene(ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film(fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise,filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil(ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil(ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil(rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation.(eda)12、工程设计自动化：engineering design automaton.(eda2)13、组装设计自动化：assembly aided architectural design.(aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display.(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format.(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization(design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router(cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing(pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction(track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole(pth)31、余隙孔：access hole32、盲孔：blind via(hole)33、埋孔：buried via hole34、埋/盲孔：buried/blind via35、任意层内部导通孔：any layer inner via hole(alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance整理自快点PCB学院。
中英文对照的PCB专业用语
中英文对照地PCB专业用语作者：深圳村村长分类:英汉词汇大全提交日期：2007-4-220:41:00 | 访问量：366一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb>5、印制线路板：printed wiring board(pwb>6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb>11、双面印制板：double-sided printed board(dsb>12、多层印制板：mulitlayer printed board(mlb>13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc>24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printedboard26、刚性双面印制板：flex-rigid double-sided printed board,rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board,rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printedboard34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum>41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc>43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs>45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob>47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc>58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl>5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay>28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose papercopper-cladlaminates(phenolic/paper ccl>40、环氧纸质覆铜箔板：epoxide cellulose paper copper-cladlaminates (epoxy/paper ccl>41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-cladlaminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glasscloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glassreinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-cladlaminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-cladlaminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxidewoven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabriccopper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-cladlaminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材地材料1、 a阶树脂：a-stage resin2、 b阶树脂：b-stage resin3、 c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe>27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi>38、聚四氟乙烯：polytetrafluoetylene (ptfe>39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylenecopolymer film (fep>40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、 e玻璃纤维：e-glass fibre43、 d玻璃纤维：d-glass fibre44、 s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil>90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil>93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc>96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔<剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad>7、计算机辅助制造：computer-aided manufacturing.(cam>8、计算机集成制造：computer integrat manufacturing.(cim>9、计算机辅助工程：computer-aided engineering.(cae>10、计算机辅助测试：computer-aided test.(cat>11、电子设计自动化：electric design automation .(eda>12、工程设计自动化：engineering designautomaton .(eda2>13、组装设计自动化：assembly aided architectural design. (aaad>14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlleddisplay .(ccd>16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf>27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化<设计）：optimization (design>31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走<布）线器：router (cad>54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp>59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线<通道）：conduction (track>2、导线<体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、 v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹<背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth>31、余隙孔：access hole32、盲孔：blind via (hole>33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh>36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance b5E2RGbCAP。
PCB综合词汇中英文对照：
PCB综合词汇中英文对照：1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-fle x double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：markPCB基材类词汇中英文对照：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates (phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad lam inates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad l aminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad lam inates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lam imates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-cl ad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminat es49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates PCB原材料化学用语中英文对照：1、 a阶树脂：a-stage resin2、 b阶树脂：b-stage resin3、 c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、 e玻璃纤维：e-glass fibre43、 d玻璃纤维：d-glass fibre44、 s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foilPCB线路设计词汇中英文对照：1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequencePCB线路形状与尺寸词汇中英文对照：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、 v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance54、基准尺寸：reference dimension55、参考尺寸：reaerence dimension56、直接量定尺寸：direct dimensioning57、基准图：datum feature58、基准边：reference edge59、导线设计距离：design space of conductor60、导线设计宽度：design width of conductor61、中心距：center to center spacing62、线宽/间距：conductor width/space63、节距：pitch64、精细节距：fine pitch65、层：layer66、层间距：layer-to-layer spacing67、边距：edge spacing68、外形线：trim line69、截面积：crossection area70、真实值表测量：truth table test71、准确位置：true position tolerance72、精确位置：accuracy73、精确位置误差：cumulative tolerance74、精确度：accuracy75、累积误差：cumulative tolerance76、焊垫：footprint77、外层：external layer78、内层：internal layer79、接地层：ground plane80、接地层隔离：ground plane clearance81、电压层：voltage plane82、电源层隔离：voltage plane clearance83、电源层：power plane, bus plane84、导通网络：basic grid85、导通网格：track grid86、导通孔网格：via grid87、连通盘网格：pad (land) grid88、定位偏差：positional tolerance89、对准靶标：bornb sight90、梳状图形：comb pattern91、对准标记：register mark92、散热层：heat sink planePCB线路电气互连词汇中英文对照：1、表面间连接：interlayer connection2、层间连接：interlayer connection3、内层连接：innerlayer connection4、非功能表面连接：nonfunctional interfacial connection5、跨接线：jumper wire6、节（交）点：node7、附加线：haywire8、端接（点）：terminal9、连接线：terminated line10、端接：termination11、连接端：pad, land12、贯穿连接：through connection13、支线：stub14、印制插头：tab15、键槽：keying slot16、连接器：connector17、板边连接器：edge board connector18、连接器区：connector area19、直角板边连接器：right angle edge connector20、偏槽口：polarizing slot21、偏置端接区：offset terminal area22、接地：ground23、端接隔离（空环）：terminal clearance24、连通性：continuity25、连接器接触：connector contact26、接触面积：contact area27、接触间距：contact spacing28、接触电阻：contact resistance29、接触尺寸：contact size30、元件引腿（脚）：component lead31、元件插针：component pin32、最小电气间距：minimum electrical spacing33、导电性：conductivity34、边卡连接器：card-edge connector35、插卡连接器：card-insertion connector36、载流量：current-carrying capacity37、蹯径：path38、最短路径：shortest path39、关键路径：critical path40、倒角：miter41、串推：daisy chain42、斯坦纳树：steiner tree43、最小生成树：minimum spanning tree (MST)44、瓶颈宽度：necked width45、短叉长度：spur length46、短柱长度：stub length47、曼哈顿路径：manhattan path48、连接度（性）：connectivityPCB线路板其他相关中英文对照：1、主面：primary side2、辅面：secondary side3、支撑面：supporting plane4、信号：signal5、信号导线：signal conductor6、信号地线：signal ground7、信号速率：signal rate8、信号标准化：signal standardization9、信号层：signal layer10、寄生信号：spurious signal11、串扰：crosstalk12、电容：capacitance13、电容耦合：capacitive coupling14、电磁干扰：electromagnetic interference15、电磁屏蔽：electromangetic shielding16、噪音：noise17、电磁兼容性：electromagnetic compatbility18、特性阻抗：impedance19、阻抗匹配：impedance match20、电感：inductance21、延迟：delay22、微带线：microstrip23、带状线：stripline24、探测点：probe point25、开窗口：cross hatching26、跨距：span27、共面性（度）：coplanarity28、埋入电阻：buried resistance29、黄金板：golden board30、芯板：core board31、薄基芯：thin core32、非均衡传输线：unbalanced transmission line33、阀值：threshold34、极限值：threshold limit value(TLV)35、散热层：heat sink plane36、热隔离：heat sink plane37、导通孔堵塞：via filiing38、波动：surge39、卡板：card40、卡板盒/卡板柜：card cages/card racks41、薄型多层板：thin type multilayer board42、埋/盲孔多层板：43、模块：module44、单芯片模块：single chip module (SCM)45、多芯片模块：multichip module (MCM)46、多芯片模块层压基板：laminate substrate version of multichip modu le (MCM-L)47、多芯片模块陶瓷基数板：ceramic substrate version o fmultichip mod ule (MCM-C)48、多芯片模块薄膜基板：deposition thin film substrate version of mu ltilayer module (MCM-D)49、嵌入凸块互连技术：buried bump interconnection technology (B2 it)50、自动测试技术：automatic test equipment (ATE)51、芯板导通孔堵塞：core board viafilling52、对准标记：alignment mark53、基准标记：fiducial mark54、拐角标记：corner mark55、剪切标记：crop mark56、铣切标记：routing mark57、对位标记：registration mark58、缩减标记：reduvtion mark59、层间重合度：layer to layer registration60、狗骨结构：dog hone61、热设计：thermal design62、热阻：thermal resistance。
PCB术语中英文对照表
Adhesion 附着力Annular Ring 孔环AOI（automatic optical inspection）自动光学检测AQL（acceptable quality level）可接受的质量等级B²it(buried bump interconnection technology) 埋入凸块焊点互连技术BBH(buried blind hole) 埋盲孔BGA(ball grid array) 球栅阵列Blister 起泡Board Edges 板边Burr 毛头/毛刺BUM(Build-up multilayer) 积层式多层板BVH（buried/blind via hole）埋/盲导通孔CAD(computer aided design) 计算机辅助设计CAM(computer aided manufacturing) 计算机辅助制造Carbon oil 碳油CEM(composite epoxy material) 环氧树脂复合板材chamfer 倒角Characteristic impedance 特性阻抗CNC（computerized numerical control）计算机化数字控制Conductor Crack 导体破裂Conductor Spacing 导线间距connector 连接器Copper foil 铜箔（皮）Crazing 微裂纹(白斑)Delamination 分层Dewetting 半润湿(缩锡)DFM（design for manufacturing）可制造性设计DIP(dual in-line package) 双列直插式组件Dk（dielectric constant）介电常数DRC(design rule checking) 设计规则检查drawing 图纸ECN(engineering change notice) 工程更改通知ECO(engineering change order) 工程更改指令E glass 电子级玻璃entek OSP处理Epoxy resin 环氧树脂ESD(electrostatic discharge) 静电释放Etched Marking 蚀刻标记Flatness 翘曲度Foreign Inclusion 外来夹杂物Flame resistant 阻燃性FR-2(flame-retardant 2)耐燃酚醛纸基板FR-3(flame-retardant 3) 耐燃环氧纸基板FR-4(flame-retardant 4) 耐燃环氧玻璃布基板FR-5(flame-retardant 5) 耐燃多功能环氧玻璃布基板ground 地面（层）Haloing 晕圈HDI(high density interconnection) 高密度互连技术HASL(hot air solder leveling) 热风焊料整平（整平）IC(integrated circuits) 集成电路Ink Stamped Marking 盖印标记Insulation resistance 绝缘电阻Ion cleanliness 离子清洁度IPC(the institute for interconnecting and packaging of electronic circu its) 印制电路互连与封装协会ISO(International organization for standardization) 国际标准化组织Laminate Voids 压合空洞laser 激光LDI(laser direct imaging) 激光直接成像legend 文字标记、符号Lifted Lands 焊盘浮起logo 标志LPI(liquid photoimageable) 液态感光成像LPISM(liquid photoimageable solder mask) 液态感光阻焊膜marking 标记Measling 白斑Microvoids 微坑mil 密耳（千分之一英寸）MIL-STD(military standard) 美国军用标准Negative Etchback 欠蚀Nicks 缺口Nodules 镀镏Nonwetting 不润湿(拒锡)open 开路OSP(organic solderability preservatives) 表面抗氧化oxides 氧化物pad 焊盘panel 拼板pattern 板面图形PCB(printed circuit board) 印制电路板Pcs(pieces) 件、片、只Peeling 剥落pinhole 针孔Pink Ring 粉红圈Pits 凹坑pitch 中心距Plating Voids 镀层破洞plug 塞Positive Etchback 过蚀power 电源层prepreg 半固化片PTFE(polytetrafluoroethylene) 聚四氟乙烯PTH(plated through-hole) 金属化孔PWB(printed-wiring board) 印制线路板Registration 对准QA(quality assurance) 质量保证QC(quality control) 质量控制QE(quality engineering) 质量工程QFP(quad flat package) 方形扁平组件repair 修理RCC(resin coated copper) 已涂覆树脂的铜箔Reference dimension 参考尺寸registration 对准度resin 树脂rejection 拒收revision 修订版RF(radio frequency) 射频Ripples 纹路rout 外形铣scratch 划伤Screened Marking 纲印标记scoring 刻槽short 短路signal 信号Silk screen 丝网Skip Coverage 漏印slot 开槽SMD(surface mount device) 表面安装器件SMOBC(solder mask over bare copper) 裸铜覆盖阻焊膜SMT(surface mount technology) 表面安装技术smear 毛刺solder 焊锡S/M(solder mask) 绿油solderability 可焊性Soda Strawing (汽水)吸管式浮空SPC（statistical process control）统计过程控制spacing 间距Tape test 胶带实验TCE（thermal coefficient of expansion）热胀系数TDR（time-domain reflectometry）时域反射测试tolerance 公差Tenting 盖孔Texture Condition 显布纹Tg(glass transition temperature) 玻璃软化温度THT(through hole technology) 通孔（插装）技术trace 线路（条）UL(underwriters laboratories) 安全实验所NPTH 非金属化孔UV(ultraviolet) 紫外线辐射v-cut V刻Via hole 导通孔（过线孔）void 空洞warp 板弯Waves 波浪Weave Exposure 露织物wetting 沾锡Wicking 灯芯效应（渗铜）Wrinkles 起皱五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer7、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：rectangle pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance。
PCB术语-中英对照
Aazoic preflux / 偶氮类预焊剂azeotropic mixture / 共沸混合物，恒沸物azeotrope / 共沸混合液xial pin package / 轴向引针封装axial part / 轴向零件axiallead / 轴向引线(脚)AWG equivalent / 等效AWGAVL / 认可的供货商，合格供货方availability factor / 可用率availability / 供应能力，供货能力auxiliary cathode / 辅助阴极auxiliary anode / 辅助阳极autotest program / 自动检测程序autotest program / 自动检测程序autoregistration / 自对准autoregistered channel contact / 自对准沟道接触autoplotter / 自动绘图仪automatic X-ray inspection / 自动X射线检查automatic testing equipment ( ATE) / 自动电测设备automatic plotting / 自动绘图automatic optical inspection( AOI) / 自动光学检测automatic laser test / 自动激光测试automatic data-processing system / 自动数据处理系统automatic control system / 自动控制系统automatic conduction routing / 自动布线automatic component placement / 自动配置元件automated test generation / 测试自动生成automated test equipment / 自动测试设备automated quality solutions (AQS) / 自动化质量解决器automated dimensioning / 自动标注尺寸automated conductor routing / 自动导体布设automated component placement / 自动元件布局automated component insertion / 自动元件插装autoclave type vacuum press / 高压釜型真空压机autoclave / 压力锅autocalytic plating / 化学镀(自催化镀)Au-Pt paste / 金铂导电膏auger electron spectroscopy(AES) / 俄歇电子光谱法aueptance / 允收attributes data / 计数数据attenuation / 信号衰减attachment by low melting alloy / 低熔点合金焊接法atmosphere corrosion / 大气腐蚀ATE / 自动电测设备asymetric stripline / 不对称带状线A-stage resin / A 阶树脂A-stage / A 阶段assembly drawing / 装配图assembly aided architectural design(AAAD) / 组装设计自动化assembly / 组装assembled drawing / 组装图assembled / 组装件as received / 到货，收货aspect ratio / 纵横比ASIC / 专用集成电路as-fired / 烧结态artwork master / 照相原版artwork / 照相底图arrow diagram / 矢量图array splice / 阵列熔接array / 阵列aromatic polyamide paper / 聚芳酰胺纤维纸argon arc welding / 氢弧焊area opening / 开孔面积arer array tape automated bonding / 面阵带式自动接合area array package (AAP) / 面积阵列封装(元件)arc resistance / 耐电弧性arc discharge / 电弧放电aramid fiber / 聚散胶纤维aramid / 聚酰胺树脂aquωus flux / 水溶性助焊剂aqueous cleaning / 水清洗AQS / 自动化质量解决器AQL / 可接收质量等级approved vendor list ( AVL) / 认可的供货商，合格供货方application specific integrated circuit(ASIC) / 专用集成电路application specific integrated circuit(ASIC) / 专用集成电路aperture turret / 同心圆apertures / 开口，钢版开口，光束出口AOM / 激光光路开关AOI / 自动光学检测any layer inner via hole ( ALIVH) / 任意层内导通孔anti-tracking coating / 保护涂层antistatic paint / 防静电涂料anti-pit agent / 抗凹剂anti-pad / 隔离环antioxidant / 抗氧化剂antimutagen / 抗诱变剂antimony free / 脱销素anti-foapting agent / 消泡剂antenna /ANSI / 美国标准协会anodizing / 阳极氧化anodized dielectric film / 阳极氧化介质膜anodization / 阳极处理anodic polarization / 阳极极化anodic oxidization or anodization / 阳极氧化anodic coating / 阳极镀层anodic cleaning / 阳极清洗anodically-grown tantalum-oxide film / 阳极生长钮氧化物膜anode sludge / 阳极泥anode slime / 阳极残渣anode sintering / 阳极烧结anode coating / 阳极镀层anode / 阳极annular width / 连接盘宽度annular ring / 孔环annular pad / 环形盘annotation / 注解，标记，注释annealing / 退火annealed copper foil / 退火铜结anneal / 韧化anisotropic etching / 单向蚀刻，各向异性蚀刻anisotropic conductive film connection(ACFC) / 单向导电膜安装，各向异性导电膜连接anisotropic conductive contact / 单向导电接触，各向异性导电接触anisotropic conductive adhesives / 单向导电黏结剂，各向异性导电黏结剂angstrom unit / 埃单位angle rotor / 角转头angle of contact / 接触角angle of attack / 刮印角angled bond / 角形连接anchoring spurs / 着力盘趾anchoring spur / 盘趾anchoring spur / 盘趾analyzer / 分析器，分析仪，检偏振器analytical ultracentrifuge / 分析超离心机analysis of covariance / 协方差分析analog circuit / 模拟电路amplitude / 电压幅度amp-hour / 安培小时amperometric titration / 电流滴定ampere / 安{培)amorphous thin film / 非晶薄膜amorphous thin film / 非晶薄膜amorphous semiconductor material / 非晶半导体材料amorphous polymer / 无定形聚合物amorphous metal mesh / 非晶金属网(ANSI) / 美国标准协会amberlite / 合成树脂amalgam gold plating / 柔齐镀金amalgamation / 汞齐化AM / 感音成像显微镜aluminum nitride substrate / 氮化铝基板aluminum nitride ceramics / 氮化铝瓷aluminium thin film / 铝薄膜aluminium oxide passivation / 三氧化二铝钝化法alumina substrate / 氧化铝基板alternative solvent / 替代溶剂alternative solvent / 替代溶剂alternatives flon cleaner / 代用氟利昂清洗剂alternative laminar technology ( ALT ) / 交错加层技术alternative hypothesis / 备择假设alternating current( AC) / 交流电ALT / 交错加层技术alphanumeric code / 字母数字代码alpha error / 第一类错误alloy plating / 合金电镀alloy junction / 合金结alloy film 合金膜/ 合金膜alloy diffusion technology / 合金扩散工艺allomerism / 异质同晶all drilled hole / 全部钻孔a1kyI-imidazol / 烷基咪唑alkaline permanganate solution / 碱性高锰酸盐溶液alkaline etchant / 碱性蚀刻液alkaline degreasing / 化学除油alkaline cleaner / 破性清洗液alkaline ammonia etchant / 氨碱蚀刻液ALIVH / 任意层内导通孔aliphatic solvent / 脂肪族溶剂alignment mark / 对准标记air sparger / 空气搅拌air knife / 气刀air inclusion / 气泡夹杂air flow impulse / 冲击式气流air bearing / 空气轴承air agitation / 空气搅拌air agitation / 空气搅拌agglomeration / 凝絮ageing / 老化affinity elution / 亲和洗脱AES / 俄歇电子光谱法adsorption dry / 吸附干燥adsorption coefficient / 吸附系数adsorption chromatography / 吸附层析adsorption / 吸附adsorbed contaminant / 吸附污染物adhesive strength of thick film conductor / 厚膜导体附着力adhesive sheet / 黏结片，半固化片adhesive face / 胶秸剂面adhesive energy / 蒸镀膜附着能量adhesive-coated uncatalyzed laminate / 涂胶无催化层压板adhesive coated surface / 涂胶面adhesive coated foil / 涂胶铜箱adhesive coated dielectric film / 涂胶黏剂绝缘薄膜adhesive-coated catalyzed laminate / 涂胶催化层压板adhesive / 胶黠剂，黠结胶，贴片胶adhesion strength / 附着力，附着强度adhesion promotor / 附着力促进剂adhesion promotion / 增教处理，附着力增强Bby-product / 副产品，副产物butt lead / 搭接引线，对接引线butting connector / 对接引脚butter coat / 厚涂层，外表树脂层burst / 并发加工bursh plating / 刷镀burr / 毛刺，毛头burnt deposit / 烧焦镀层burn-out zone / 烧除气体区burn-out gas / 烧除气体burn in static / 静态老化burning / 烧焦burn in dynamic / 动态老化burn in / 老化buried via hole / 埋导孔，埋孔buried via / 埋孔buried resistance board / 埋入电阻板buried resistance / 埋入电阻buried microvias / 微埋孔buried hole / 埋通孔buried bump interconnection technology(B'it) / 嵌入凸块互连技术，埋入凸块互连技术buried and blinded via hole multiplayerboard / 埋/盲孔多层板bumping process / 凸块工艺bumping / 凸块封装技术bumped wafer / 带凸块晶片bumped tape automated bonding(BTAB) / 有凸块的带载自动焊接，凸点带载自动焊bumped tape / 带凸块载带bumped die / 带凸块芯片，带凸块的裸芯片bumped ball grid array (BBGA) / 凸块球栅阵列bump / 突块，凸块BUM / 积层多层印制板bulls eye / 靶心，定位标识bullet pad / 子弹形盘bulk feeder / 散装供料器bulge test / 鼓凸试验bulge / 凸起，凸出，鼓起，隆起built-in / 内建build-up process / 积层工艺，积层法build-up multilayer printed board(BUM) / 积层多层印制板build up method / 积层法build-up flexible printed board / 积层挠性印制板build-up / 增厚;堆积，积层bugle hole / 喇叭孔bugging height / 障碍高度buffing / 抛光研磨buffer material / 缓冲材料buffer material / 缓冲材料buffer / 缓冲剂bubble effect / 气泡效应BTAB / 有凸块的带载自动焊接BT / 双马来酰亚胺三嗦树脂B-stage resin / B 阶树脂B-stage prepreg / B 阶教结片B-stage material / B 阶材料B-stage Lot / B 阶批量B-stage Lot / B 阶批量B-stage / B 阶段BS / 基础规范brush plating / 刷镀，电刷镀brushing / 磨刷brown streak / 棕色条纹brown oxide / 棕色氧化处理，棕色氧化brown oxidation / 棕氧化brittleness / 脆性Brinell hardness / 布氏硬度bright plating / 光亮电镀bright pickling / 光亮浸蚀brightness nickel plating / 光亮镀镍brightening agent / 光亮剂brightener / 光泽剂bright dip / 光泽浸渍处理，浸亮bridging / 跨接bridge / 锡桥break point / 出像点，显像点，露铜点break-out / 破环break-out / 破环breaking length / 断裂长breakdown voltage / 崩溃电压，击穿电压bleakaway panel / 可断开板，可断拼版brazing / 纤焊，硬焊brazability / 纤焊性braid / 编线BQFP / 带防冲挡四边扇平封装器件box diffusion / 箱法扩散bow of weave / 弓纬bow / 弯曲，扭曲，板翘boundary scan test / 边界扫描测试boundary / 边界，界面，界线bounce pad / 反射盘bottom / 言孔底部bottle neck / 瓶颈工序boss / 凸台bornb sight / 对准靶标bornb sight / 对准靶标border data / 外框数据，板框数据，边沿数据border conveyor / 边框传送器，筋条传送器border area / 边沿区，外框bond-to-die distance / 芯片接合距离bond-to-bond distance / 接合间距离，连(焊)接距离bond surface / 接合面bond strength / 黏合强度，黏结强度bond site / 接合位置，连(焊)接位置bond site / 接合位置，连(焊)接位置bond separation / 接合间隔bond lift-off / 接合脱离bond land / 连(焊)接盘bond interface / 接合界面，接合连接盘bond interface / 接合界面，接合连接盘bond interface / 接合界面，接合连接盘bonding wire / 连(焊)接金属丝，接合金属线bonding tool / 接合工具bonding time / 接合时间bonding tester / 黏结测试器bonding tester / 黏结测试器bonding technology of integrated circuit / 集成电路焊接工艺bonding strength / 黏结强度bonding sheet / 黏结片bonding pad / 键合点bonding layer / 黏结层，结合层bonding island / 接合岛，连{焊)接岛bonding die / 接合芯片booding area / (焊)接面积，接合区域bonding / 键合，连(焊)接bond envelope / 接合包封bond enhancement treatment / 黏结增强处理bonded-contact board / 焊接板bond deformation / 接合变形bondability / 可键合性，可接合性bond / 接合，连(焊)接bomb sight / 弹标BOM / 物料清单boiling water absorption rate / 煮沸吸水率boiling point / 沸点body land clearance / 刃带间隙BOD / 生化需氧量board thickness / 板厚度，板厚board-mounted connector / 板装引脚board / 板blur edge / 模糊边带，模糊边圈blue-ribbon connector / 矩形插头座blue plaque / 蓝纹blow hole / 吹孔，气孔blotting paper / 吸墨纸blotting / 干印，吸墨blockout / 封网blocking variables / 变量隔离blocking contact / 阻挡接触blocking band curvature / 阻挡层能带弯曲block diagram / 方框图blister / 起泡blind via hole / 盲导通孔，盲孔blind test / 双盲试验blind surface microvias / 表面微盲孔blind conductor / 非功能性导线blends / 配料bleeding / 渗出，渗漏bleach / 漂洗blanking / 冲切加工blanking / 冲切加工blanket gas / 保护气体blank / 坯料，空白料blade-fork contact / 刀刃音叉式簧片black oxide / 黑氧化，黑化blackening / 涂黑bits / 头，针尖B' it printed board / 埋入式凸块互连印制板bismaleimide triazine resin(BT) / 双马来酰亚胺三嗦树脂bismaleimide triazine epoxide wovenglass fabric coppe.-c1ad / 双马来酰亚胺三嗦环氧玻璃布覆铜箔板bismaleimide / 双马来酰亚胺birdcage / 笼状缺陷biochemical oxygen demand ( BOD) / 生化需氧量binder / 黏合剂，黏结剂bill of material (BOM) / 物料清单bi-level stencil / 双阶式钢版bifurcated solder terminal / 分叉焊端，分叉焊接端子bifurcated contact / 双叉式簧片，双叉接点，双叉接触件bifunctional catalyst / 双功能催化剂bidirectional characteristic / 双向特性bidirectional characteristic / 双向特性bias sputtering / 偏压阴极溅镀bias expansion / 斜张法bias / 纬斜BGA / 球栅阵列beveling / 倒斜边，切斜边beta error / 第二类错误BeO substrate / 氧化镀基板bend test / 弯曲试验bendability / 耐弯曲性benchmark testing / 测试基准belt furnace / 带式炉bellows contact / 折叠式簧片，扁簧式接触件bed-of-nails testing / 针床测试bed-of-nails fixture / 针床夹具beam reflow soldering / 光束回流焊beam lead isolation / 梁式引线隔离beam lead-isolated integrated circuit / 梁式引线隔离集成电路beam lead device / 梁式引线器件beam lead bonding technology / 梁式引线载带自动焊接芯片工艺beam lead bonder / 梁式引线键合机beam lead / 梁式引线，梁式引脚Ccyclone jet / 旋风式喷气流cyclic voltametric stripping (CVS) / 循环伏安测量法，循环伏安电子溶蚀测量cycle rate / 循环速率cycle mode / 逐次打击式cycle / 循环加工CVS / 循环伏安测量法CVD / 化学气相沉积cut to size panel / 剪切板cut sheet / 页装cut-off / 割除，切割cut-and-strip / 刻图与剥图cut and peel / 切割剥离cusum chart / 累积和图customer relationshipmanagement(CRM) / 客户关系管理customer detail specification ( CDS) / 用户详细规范cushion / 压垫(缓冲)材料curtain coating / 帘涂，帘幕涂布法current efficiency / 电流效率current density range / 电流密度范围current density of junction / 结电流密度current density / 电流密度current-carrying capacity / 载流能力，载流量current / 电流curing temperature / 固化温度curing agent / 困化剂cure time / 固化时间cure percent / 固化百分率cure / 固化cup solder terminal / 杯型焊端cupric chloride etchant / 氯化铜蚀刻液cumulative tolerance / 积累误差cubic components / 立方体元件，立方体器件CTS / 能力试验块CTP / 综合测试图形CTE / 热膨胀系数CTB / 能力试验板C-staged resin / C 阶树脂C-stage / C 阶段CSP / 芯片尺寸封装，芯片级封装crush zone / 磨碎区cross wise direction / 横向crossunder / 穿交crosstalk / 串扰cross section area / 截面积cross-over / 跨交cross linking / 交链crosslink / 交联crossing count / 交叉数crosshatch testing / 十字割痕试验crosshatching / 十字交叉线cross flow blower / 贯流式风机cropping / 切尾crop mark / 剪切标记CRM / 客户关系管理critical process / 关键过程，关键工序critical path method (CPM) / 要径法critical path / 关键路径critical operation / 关键操作critical defect / 致命缺陷，关键缺陷crimped connection / 压接crimp contact / 压扁接触片crevice corrosion / 裂隙腐蚀creep / 潜变，蠕变creel / 经轴架crease / 皱褶cream electrolyte / 导电膏creak / 础裂痕crazing( conformal coating) / (敷形涂层)微裂纹crazing (base material) / (基板)微裂纹crazing / 微裂纹cratering / 陷坑crater / 弹坑，凹坑crack of plating / 镀层裂缝crack of foil / 金属第裂缝CQFP / 陶瓷四边扁平封装CPM / 要径法CPM / 客户抱怨比Cpk index(Cpk) / Cpk 指数CP-I etch / CP-I 腐蚀CPGA / 陶瓷针式网格阵列，陶瓷封装CP6 etch / CP6腐蚀CP4 etch / CP4 腐蚀Cp / 能力性能指数coverlayer / 保护层，外膜cover lay / 覆盖层covering power / 覆盖能力cover coat / 覆盖涂层coupon / 板边试样，附连板coupling agent / 偶联剂counter sinking / 锥形孔counter flow / 上下翻流，上下回流counter current rinsing / 逆流漂洗counter boring / 垂直向下扩孔，埋头孔，沉头孔cost of quality / 质量成本cost metrix / 费用矩阵corrosive flux / 腐蚀性焊剂corrosion protection / 防腐蚀corrosion of metals / 金属腐蚀corrosion / 腐蚀corrode paste test / 倒腐蚀膏试验corner mark / 板角标记，角标corner crack / 孔角断裂core material / 内层板材，芯材core board via filling / 芯板导通孔堵塞core board / 芯板cordwood module / 积木式微型组件cordwood arrangement / 积木式排列copper thick film printed wiring board / 铜厚膜印制板copper side / 铜箔面copper plating adhesion test / 铜镀层附着力测试copper plating / 电镀铜copper plated-through hole / 镶铜导通孔copper plated-through hole / 镶铜导通孔copper plated-through hole / 镶铜导通孔copper paste / 铜膏copper-mirror test / 铜镜试验copper invar copper core (CICC) / 因瓦合金copper-invar-copper board / 因瓦铜夹心板copper foil surface treatment / 铜箔表面处理copper foil laminate 覆铜箔板/ 覆铜箔板copper foil / 铜箔copper cyanide plating / 氟化铜镀copper clad laminate board (CCL ) / 覆铜箔层压板，覆箔板copper clad industrial laminate (CCIL) / 凭申请认证制度，CCll 制度copper accelerated salt spray test / 铜加速盐雾试验，CASS 试验coplanar leads / 共面引脚，共面引线coplanarity / 共面性(度)cooler / 冷却器convection/IR reflow soldering / 热对流红外辐射回流焊control strip / 光尺control limits / 控制限controlled depth drilling / 定深钻孔，钻孔深度控制controlled collapse chip connection / C4晶片焊接，控制熔化高度芯controlled collapse bonding (CCB ) / 控压连(焊)接controlled collapse bonding (CCB ) / 控压连(焊)接controlled collapse / 定高坍塌control collapse soldering / 控制崩塌焊接control chart / 控制图contract service / 外包厂，分包商，外协加工contract electronic manufacturer(CEM) / 电子品合同式制造商contour length / 伸展长度continuous lamination / 连续压合，连续层压continuity inspection / 连通检查continuity / 连通性contact tenting light frame- work / 接触式蔽光框架法contact spring / 接触弹簧contact spacing / 接触间距contact size / 接触尺寸contact retention force / 接触阻力contact resistance / 接触电阻contact printing / 接触印刷，接触曝光contact plating / 插头电镀contact photo-printing / 接触式感光印制contact length / 接触长度contact hole / 接触孔，引线孔contact hardening / 接触硬化contact force / 接触压力contact exposure imaging / 底片接触曝光成像contact corrosion / 接触腐蚀contact bonding adhesive / 接触黏合剂contact area / 接触区，接触面积)(焊接)接触角/ (焊接)接触角contact aluminium / 铝接触contact alloying / 接触合金contact / 接触件constraining core / 加强芯板，夹芯conner mark / 角标志connector with mixed contacts / 混装式引脚connector two-part printed board / 印制板双件引脚connector two-part / 双件引脚connector one-part / 单件引脚connector housing / 引脚座connector contact / 引脚接触件connector area / 引脚区域connector / 引脚connectivity / 连接度conformal mask / 敷形掩模conformal coating / 敷形涂层，保护形confirmation run / 确认试验confidence interval / 置信区间cone type sprayer / 圆锥型喷嘴cone-formation / 锥形缺陷conductor width/space / 线宽/间距conductor width / 导线宽度conductor track / 导电带conductor trace line / 导线conductor to land spacing / 导线与连接盘间距conductor to hole spacing / 导线与孔间距conductor thickness / 导线厚度conductor spacing / 导线间距conductor side / 导线面conductor resistance /conductor pitch / 中心线距，导体节距conductor pattern / 导线图形conductor line / 导体线conductor layer / 导线层，导体层conductor exposure / 露线conductor base width / 基板导线宽度conductor base spacing / 基板导线间距conductor / 导电带，导线Ddynamic mechanical analysis ( DMA ) / 动态秸弹性分析，动态热机分析dynamic flexible printed board / 挠性印制板dynamic flex board / 动态挠性板dusting method / 喷粉法durability / 耐久性dummy substrate / 模仿基饭，伪基板dummy plating / 假电镀dummy pattern / 虚拟图形dummy / 假镀片(板).假阴极dumet / 杜美丝ductility / 延展性dual wave soldering / 双波蜂焊接dual transistor / 双晶体管dual-strip line / 双带状线dual inline package ( DIP ) / 双列直插式封装dual inline memory / 双列直插式存储器模块dual-ground connection / 双地线连接dual fixture / 双重夹具，双组夹具dual coated fiber / 双涂覆层光纤dual beam laser interferometer / 双束激光干涉仪DSW / 直接分步重复曝光DSS / 决策支持系统DSA / 尺度稳定式阳极DS / 详细规范dry process / 干法工艺dry plate / 干版dry photoetching technology / 干法刻蚀工艺drying / 干燥dry film resist / 干膜抗蚀剂dry film photo resist / 干膜光致抗蚀剂dry film imaging / 干膜法图形转移dry film / 干膜dryetching / 干刻dry box / 干燥箱drum side / 铜第光面，光阴面drum scan type plotter / 鼓形扫描绘图机drum scan type plotter / 鼓形扫描绘图机drum-buffer- rope( DBR) / 限制驱导式排程法dross / 浮渣，焊渣，残渣dropping corrosion test / 点滴腐蚀试验dropping / 点滴(胶)法drive file / 驱动文件drill pointer / 磨尖机，磨钻头机drill point concentricity / 钻尖同心度drilling / 钻孔drill facet / 钻头切削面drilled bare board / 己钻孔裸板drill drawing / 钻孔图drill diameter / 钻头直径drill body length / 钻体长度drill axis / 长刃drawbridging / 吊桥效应drawbridged component / 吊桥元件drag soldering / 拖焊drag out / 带出drag in/drag out / 带进/带出drag in / 带进drafting image / 绘制图像DPA / 破坏性物理分析DP / 交货拼板downtime / 停机时间double wet pass / 两次湿印法double treated foil / 双面处理铜箔double sided treated copper foil / 双面粗糙铜箔，双面粗化金属箔double-sided printed wiring board / 双面印制线路板double-sided printed board / 双面印制板double-sided flexible printed wiring board /双面挠性印制线路板double-sided copper-clad laminate / 双面覆铜箔层压板double sided board / 双面板double sided board / 双面板double-sided assembly / 双面组装件double sided abrasive machine / 双面研磨机double resist exposure / 二次抗蚀剂曝光doubl-plug diode / 双插头二极管double level routing / 双层布线double layer / 双电层double density / 双密度double access / 双面露出，双余隙doping technique / 掺杂工艺doping accuracy / 掺杂精度doping / 掺杂doped epitaxial layer / 掺杂外延层doped dielectric / 掺杂电介质dopant redistribution / 掺杂剂再分布dopant material / 掺杂剂材料dont-care area / 忽略区dog ear / 狗耳dog bone design / 哑铃式互连设计，狗骨式互连设计dog bone / 狗骨结构doctor blade method / 刮板法doctor blade / 修平刀，刮平刀DO / 溶氧量，溶解氧DNC / 分布式数控3D-MCM (three dimension multi-chip module) / 三维多芯片模块封装DMA / 动态热机分析disturbed soldered connection / 紊流焊料连接disturbed joint / 受扰焊点disturbed connection / 移位焊点distributed numerical control (DNC) / 分布式数控distributed constant circuit / 分布参数电路distributed capacitance / 分布电容dissolved oxygen (DO) / 溶氧量，溶解氧dissolution of termination metallization / 端子金属化溶失dissolution of metallization / 金属化溶失dissipation factor / 损耗因数，耗散因数dispersion coating / 弥(扩)散电镀dispersion / 溶胶剂dispersing technique / 分散工艺dispersant / 分散剂dispensing / 滴涂，逐点分配，定点分配，定量分配dispenser / 滴涂器dispense method / 点胶法dish down / 碟形下陷，凹陷discretionary wiring / 选择布线discrete wiring board assembly / 分立布线印制板组装discrete wiring / 分立布线，离散布线discrete component / 分立元件discrepant material / 不合格材料discharge spot welding / 储能点焊direct step on wafer(DSW) / 直接分步重复曝光direct plating / 直接电镀，直接镀板direct indirect stencil / 直间版膜direct imaging method / 直接成像法direct film / 直写底片direct emulsion / 直接乳胶direct electron beam lithographic systern / 电子束直接曝光装置direct drawing method / 直接绘图法direct dimensioning / 直接尺寸标注direct current sputtering / 直流溅射法direct cleaning / 直流清洗direct chip attaching (DCA) / 直接芯片贴装dip soldering / 浸焊，拖焊法dipping / 浸渍法diphase cleaning / 双相清洗dip coat / 浸涂法DIP / 双列直播式封装dimpled ball grid array(DBGA) / 微凹球栅阵列dimple / 微凹3-dimension mounted technology / 3-D安装技术dimensioned hole / 注尺寸孔dimensional variation ratio / 尺寸变化率dimensional stable anode( DSA) / 尺度稳定式阳极，非溶解式阳极dimensional stability / 尺度安定性，尺寸安定性dihedral angle / 双反斜角digitize / 数字化digital circuit / 数字电路diffusion under epitaxial layer / 外延层下扩散diffusion technique / 扩散工艺diffusion self-aligned technology / 扩散自对准工艺diffusion mask / 扩散掩模diffusion layer / 扩散层diffusion bond / 扩散连(焊)接differential etching / 差分蚀刻法die stamping method / 模压法die stamping / 冲压，模具压印die pad / 裸芯片连接盘die mounting / 芯片装架dielectric thin film / 介电薄膜dielectric substrate isolation / 介质衬底隔离dielectric strength / 介质强度，抗电强度dielectric spacing / 介质间距dielectric power- factor / 介质功率因数dielectric phase angle / 介质相位角dielectric paste / 介电膏dielectric loss angle / 介质损耗角dielectric loss / 介质损耗dielectric isolation / 介质隔离dielectric gap / 绝缘间隙dielectric film / 介质胶片dielectric dissipation factor / 损耗因数，介质损耗因数dielectric dispersion / 介电分散dielectric constant / 介电常数dielectric breakdown voltage / 介质崩溃电压dielectric breakdown / 介电击穿dielectric / 介质die bump / 芯片凸块die bonding / 裸芯片连(搭)接die attachment using alloy solder / 合金法粘片die attachment technology / 芯片安装技术die / 裸芯片D-glass / D-玻璃纤维板device / 器件detailed specification ( DS) / 详细规范destructive physical analysis ( DPA ) / 破坏性物理分析desoldering station / 吸锡台desoldering gun / 吸锡枪depolarization / 去极化dependent of feature size / 要素尺寸相关原则dependant demand / 相依需求depanelization / 切开，分开dentrices / 树枝状物dent / 凹陷densitometer / 光密度计densitomer / 透光度计denier / 但尼尔dendritic migration / 树枝状迁移dendritic growth / 枝状生长，树枝状生长demountable vacuum system / 可拆卸真空系统demarcation line / 分界线delivery inspection / 发货检查Eeyelet bond / 环形压焊extrusion pressing / 挤压成型extrusion of conductor width / 导体过宽extrasing moulding / 挤塑法extrinsic capacitance / 外部电容extra via hole / 多余孔extraneous metal / 残余金属extraneous copper / 残余铜extra high frequency ( EHF) / 超高频电磁波extraction tool / 拔除工具external layer / 外层extended card / 引伸插件exposure experiment / 暴露实验exposure effect / 暴露影响exposure dose / 照射剂量exposure / 曝光experimental error / 试验误差expansion-matched plastic / 膨胀系数匹配塑料expanded contact / 延伸接触exothermic reaction / 放热反应exotherm / 放热曲线exfoliation / 鳞皮exclusion area / 排除区;免验区excising / 切除，外引线切除，外引线切割excising / 切除，外引线切除，外引线切割excess solder connection / 过量焊点evaporative rate analyzer (ERA) / 挥发率分析仪evaporation source / 蒸发源evaporation mask / 蒸发掩模evaporated dielectric film / 蒸发介质薄膜evaporated dielectric deposition / 蒸发介质涂覆eutection / 低共熔合金eutectic solders / 共晶焊料eutectic die attach / 低共熔芯片贴装，低共熔点裸芯片连接eutectic composition / 共熔组成eutectic bonding / 共晶焊eutectic / 共熔etra-etch / 氟树脂粗蚀剂ethanol / 乙醇etch-pit density / 腐蚀坑密度etch pit / 腐蚀坑etching technology / 刻蚀工艺etching resist ink / 抗蚀印料etching resist / 抗蚀剂，抗蚀层etching rate checking / 蚀刻速率测定etching of aluminum foil / 铝箔腐蚀etching mask / 抗腐蚀掩模etching indicator / 蚀刻指标，蚀刻指示图etching / 腐蚀，蚀刻etch factor / 蚀刻因子，蚀刻函数etched V-groove silicon chip ribbon fiberconnector / 硅片刻蚀V 槽带状光纤引脚etched printed boards / 己蚀刻印制板etched out surface / 去铜箔面etch depth / 腐蚀深度etchback shadowing / 凹蚀死角etch back / 凹蚀etchant / 蚀刻剂，腐蚀剂ESS / 环境应力筛选escapes / 漏失escapes / 漏失escape rate / 漏失率ESC / 环氧树脂囊包焊接error / 误差ERA / 挥发率分析仪equivalent effective stratωpheric chlorine(EESC) / 氯浓度epoxy value / 环氧值epoxy transistor / 塑封晶体管epoxy transfer-moulding powder / 塑封用环氧树脂粉epoxy smear / 环氧腻污，环氧钻污epoxy resin / 环氧树脂epoxy novolac / 环氧酚醛epoxy glass substrate / 环氧玻璃基板epoxy-glass printed-circuit board / 氧玻璃印制电路板epoxy encapsnlation /epoxy-encapsulated solder connection(ESC) / 环氧树脂囊包焊接epoxy / 环氧树脂epoxide woven glass fabric copper-clad laminates / 环氧玻璃布基覆铜范板epoxide synthetic fiber fabric copperclad laminates / 环氧合成纤维布覆箔结板epoxide non woven woven glass reinforced copper-clad laminat / 环氧玻璃布玻璃纤维复合覆铜箔板epoxide cellulose paper core glass cloth surfaces copper-cla / 环氧玻璃布纸复合覆铜箔板epoxide cellulose paper copper-clad laminates / 环氧纸质覆铜箔板epitaxial substrate / 外延衬底epitaxial step / 外延台阶epitaxial step / 外延台阶epitaxial stacking fault / 外延堆垛，外延层错epitaxial slice / 外延片epitaxial region / 外延区epitaxial process / 外延过程epitaxial layer / 外延层epitaxial isolation / 外延隔离epitaxial growth technology / 外延生长工艺，外延生长技术environment factor / 环境系数environmental test / 环境试验environmental stress screening ( ESS ) / 环境应力筛选environmental impact assessment / 环境影响评价environmental impact / 环境影响environmental characteristic / 环境特性entry material / 盖板engraving / 刻槽engineering plastic / 工程塑料engineering drawing / 工程图engineer change request notice ( ECRN) / 原件规格更改通知energy dispersive X-ray analysis (EDX) / 能量扩散×射线分析endurance test / 耐久性试验end product / 最终产品，终产物end missing / 断经end missing / 断经end missing / 断经end mill / 端铁刀end item / 最终成品end cap / 封头enclosure / 机箱enclosed metal junction / 内封金属连接encapsulation / 密封，封装encapsulating / 囊封，胶囊encapsulant / 封装剂encapsolation test / 密封性试验emulsion side / 乳胶面emulsion side / 乳胶面emulsion screen / 乳胶网版emulsion mask / 乳胶掩模emulsion degreasing / 乳化除油emulsion / 乳剂层emulsifying agent / 乳化剂emulsification / 乳化emission standard / 排放基准EMI / 电磁干扰emergency pit / 应急槽，备用槽EMC / 电磁兼容性embossing / 凸出性压花embedding / 灌封embedded component / 埋入元件embedded component / 埋入元件emanation overlay / 放射性同位素涂层elongation / 延伸性，伸长率elementary diagram / 接线原理图elementary analysis / 元素分析electro-winning / 电解冶炼electroviscous effect / 电黏效应electrostriction / 电缩作用electrostatic spray / 静电喷涂electrostatic coat / 静电涂覆electrosorptive spreading / 电吸附散布electrosolishing / 电抛光electroplating / 电镀electro phoretic photo resist / 电泳光致抗蚀剂electrophoretic mobility / 电泳迁移率electrophoretic effect / 电泳效应pelectrophoresis deposition coating process /电泳沉积法electrophoresis / 电泳electroosmosis / 电渗electronic packaging / 电子组装electronic package hierarchy / 电子构装层级electronic desorption / 电子碰撞解吸electronic data interchange format(EDIF) / 电子数据互换格式electron-exchange resin / 电子交换树脂electron cyclotron resonance plasma deposition / 电子回旋谐振等离子体沉积electron cyclotron resonance ion beam etching / 电子回旋谐振离子束刻蚀electron beam welding machine / 电子束焊接机electron bearn welding / 电子束焊electron-bearn-sensitive diffusion mask / 电子束敏感扩散掩模electron-bearn photo- resist exposure / 光致抗蚀剂电子束曝光electron beam melting system / 电子束熔化装置electron beam lithography / 电子束曝光electron beam lithographic machine / 电子束曝光机electron beam evaporation deposition / 电子束蒸发沉积electron beam curing method ( EBC ) / 电子束固化方式electron beam cure paint / 电子束固化涂料electron-beam bonding / 电子束连接electro migration / 电迁移electro magnetic shield paint / 电磁屏蔽涂料electro magnetic shielding / 电磁屏蔽electro magnetic interference sealed film / 电磁干扰屏蔽膜electro magnetic interference ( EMI ) / 电磁干扰electro magnetic compatibility (EMC ) / 电磁兼容性electro magnetic compatibility (EMC ) / 电磁兼容性electrolytic deposition speed / 电解沉积速度electrolytic deposition / 电解沉积electrolytic degreasing / 电解除油electrolytic corrosion test at edge / 边缘腐蚀试验electrolytic corrosion at edge / 边缘腐蚀electrolytic corrosion / 电蚀electrolytic cleaning / 电解清洗electroless plating / 无电电镀electroless nickel phosphorus plating / 化学镀Ni-Pelectroless nickel/immersion gold (EN/IG) / 化镇浸金electroless nickel boron plating / 化学镀Ni-B electroless gold plating / 化学镀金electroless deposition / 化学镀，化学沉积，无电沉积electroless deposition / 化学镀，化学沉积，无电沉积electroless copper plating / 化学沉铜electroless composite coating / 组合化学镀electroforming / 电铸，电形成electroformed photomask / 电铸光掩模板electrodeposition / 电镀，电解电镀，电沉积electro-deposited photoresist / 电泳沉积光致抗蚀剂electrode depoited / 电解箔，电沉积箔electroconductive paste printed board / 导电胶印制板electrochemical impregnation / 电化学浸渍electrochemical equivalent / 电化当量Ffusing oil / 热熔液(油)fusing flux / 热熔焊剂，热熔助焊剂fusing fluid / 热熔液，助熔液fusing / 熔融fusible link / 可熔互连fused coating / 熔锡层，热熔涂覆层fungus resistanα / 抗霉性，防霉性functional trimming / 功能调整functional tester / 功能测试器functional test / 功能测试functional film / 功能膜functional device / 功能器件functional ceramics / 功能陶瓷functional array / 功能阵列。
PCB专业术语中英文对照
1影响电性及外观Affect upon electrical performance or appearance2过度的Excessively3异常Abnormal4规格不符specification is below standard5品质异常quality is below standard6严格按照QC规定Strictly according to QC regulation7定期研磨To make regularly re-sharpen8设备device(另義:主動零件) \ machine \9参数设置错误parameters setting error10依保养计划According to the maintaining plan11压力过小lack of pressure12曝光不全\过度exposure-energy insufficient\excessive 13间距不足spacing nonenough14线细width reduce15光强度Light Intensity16缺口nick\chipping17气泡Bubble\blister\air inclusion18异物foreign particle \ foreign material（壓合異物）\dust(灰塵)19被污染contaminated20干膜附著力不足 Poor adhesion of dry film21固定点开路fixed position open22固定点短路fixed position short23线路针孔trace pin-hole24孔破void in PTH hole\Barrel Crack25断脖子Open near pad26静置时间Holding time27识别方法identify method28膜屑反粘Contrary to adhere of scum29碎屑,残材 Debris30显影不洁Developing uncleanness 31外观不良Appearace defective32传动\传送速度convey speed33偏离deviation\shifted34单轴single axis35底片涨缩A/W expand or contract 36漏失率 Loss Rate37补偿compensation\balancing 38零件孔\面component hole\side39覆铜箔层压板\铜箔基板copper clad laminates (CCL)40线路露铜copper exposure41织纹显露weave exposure42光学点\基准标记fiducial mark43环氧树脂epoxy44蚀刻速率etch rate45网布fabric46助焊剂不均匀flux coating uneven 47过滤filtration48电测治具fixture49钻尖分离gap50标准板golden board1影响上件及外观affect upon mounting or appearance2铜厚测量仪Copper thickness Measuring Instrument 3佐证evidence4微蚀量microetching quantity5 湿度humidity6内部校正周期(校验矫正)internal proofread cycle\calibrationsystem cycle7板面刮伤Surface Scratch8制定handling 标Define standard of handling 9目视检查\目检visual inspection10规定频率defined frequency11压力计\表pressure gauge12工程程式designed program13超规格out of the tolerance14毛头\去毛头burr\deburring15影响下工序制作difficult to product in the following process16化学铜electroless plating17除胶速率desmearing rate18电流current19分层delamination\bulge20湿润Damped21预浸Pre-dipped22活化液activator23速化accelerator24漂锡solder float25热应力测试thermal stress test26孔环(焊垫)Lifted land\annular ring 27热水洗Hot water rinsing28震动马达vibrating motor29铜渣copper residue (copper splash)\cosmetics island獨立銅渣30清洁滤网purifying filters31定期换水replace water regularly32回收槽recovery tank33加强管控to strengthen the control of sth.34酸洗\硷洗acid\alkali rinse35定期分析浓度Analyze Conc. regularly36金属杂质污染Contamination of metal impurities37碳化物carbide38碳处理carbon treatment39整流器(电流矫正)Current rectifier40铜厚测量仪Copper Thickness Measuring Instrument 41刷磨速度Brush Speed42速度控制器velocity controller43电流控制器current controller44吸水滚轮破旧water-absorptive roller worn-out45新水补充不足Insufficient for water replenishment 46滤芯Filter element47化学药液chemicals liquid48孔塞(孔内异物)dirty hole49多与\少与1mil厚度Less\More than 1 mil Thickness50色差color variation1板面粘油墨屑(显影段)sticky ink debris2挡水滚轮water apart roller3网板高度Screen height4网板张力不足Screen tension insufficient5刮刀行程Squeegee distance6刮刀刃钝化Squeegee edge blunt7油墨黏度过大viscosity of ink too thick8张力应力tensile stress9后烤Post cure10印C面Printing Top(COMP) Side11印S面Printing (SOLD)Bottom Side12静电喷涂Spray Coating13印可剥胶Peelable Solder Mask14风刀air knife15隔离环clearance16烧焦burning17化镍金immersion nickel and gold18铜镍层接著不良Poor combination the copper and nickel 19刷磨滚轮brush roller20刷幅测试brush breadth\width test21脱脂温度Defatting Temp.22流量计flowmeter23执行\导电Conduct24助焊剂\熔合液rosin(天然松香)\flux\fusing fluids25锡粗Tin roughness26焊料中铜离子含量过高The cu2+ content out of upper in solder 27机台异常machine-motion error28缺点标示卡nominal card of defects29程序\程式错误Programbug30人员疏忽operator's carelessness31日保养daily maintainance32人员技能不熟练Operator is not skilled33口头考核examine orally34阻抗异常Impedance Abnormal35阻抗测量仪impedance measuring instrument36漏气puncture37受潮moisture absorption38膜面污染film surface contaminated39漏检Leaking inspection40二次元 2D(biaxial) dimension-measuringinstrument41工单run card\work order42飞针Flying Probe43目检Visual Inspection44专用治具测试Dedicated Tester45特殊特性Critical Feature46重要特性Important Feature47铜箔厚度Copper foil Thickness48板弯翘Bow and Twist(warp)49尺寸(含对角)Size(Diagonal)\dimensions(成型) 50拉力计\张力计tensile meter1棕化\黑化Brow\black oxide2循环水洗circulating water rinsing3PP胶片Prepreg4物理性质\化学性质physical\chemical character5暂存时间Temporary store time6铆钉组合Eyelet7叠板结构stacking(lay up) structure8铆钉rivet9热熔机heat-melting machine10有用寿命useful life11印制电路板Printed Circuit Board(PCB)12根本原因\真因Root Cause13围堵措施Containment Plan14现状Current Status15原因分析Gap Analysis16内部稽核\外部稽核Internal\outside Audit17修改\变更Modify18无卤素Halogen Free19更新\修订Update/Revise20改进措施ure Plan21长期异常Chronic22突发异常Excursion23陶尔(压力单位)Torr24靶孔距Space between target holes25层偏misalignment26组合线Combined producing line27钢板\隔板steel plate\caul plate\separator28板厚测量仪Board-thickness measuring instrument 29钢印机 steel seal machine30品质检验 quality examination31介质厚度dielectric thickness32吸水性moisture absorbability33耐磨性wear resistance34剥离强度stripping strength35焊锡耐热性heat-resistant of solder36抗麻斑测试spot-resistant test37信赖性测试reliability test38介电常数测量仪dielectric constant measuring device 39包装标籤packing tag40电子天平electrical balances41焊锡炉solder furnace42孔径规calliper gauge43比色计color comparing meter44密度计density meter45蚀刻均匀性Etching uniformability46化验单 laboratory list47出货单manifest48双面板\多层板 Reversible Board\Multi layer board 49定位孔 Location Hole50叠板数stack boards count1硝基戊烷amylnitrite2阳极泥anode slime (sludge)3液态光阻aqueous photoresist4纵横比aspect ratio5预留在制品banked work in process 6贝他射线照射法beta backscattering7斜边beveling8吹孔blow hole9黏结层bonding plies10焊桥solder bridge11接单生产Build To Order(BTO)12金手指斜边\倒角chamfering13网框chase14螯合剂chelator15化学键chemical bond16热膨胀Thermal Expansion17同心圆concentric circle18密贴性conformance19消费类产品consumer products20库伦定理coulombs law21喇叭孔countersink22试样coupon\sample23覆盖力covering power24挖空cut-outs25交期缩短cycle-time reduction 26专用型dedicated27缩锡dewetting28介质常数dielectric constant29孔黑\孔灰discolor hole30停机\稼动时间downtime\uptime31钻针切削面drill facet32钻针研磨机drill pointer33裸板(未镀铜) blank board34延展性ductility\Elongation35留边宽度edge spacing36金手指edge-board contact ( gold finger )\tab 37电化学反应器electrochemical reactor38脆性embrittlement39植PIN法\外部插梢法external pin method40织维突出fiber protrusion41成品final board42固著fixing43燃烧等级flammability rating44抗菌性\抗酶性fungus resistance45胶化时间gel time46一般阻焊油墨general resist ink47玻璃态转换温度glass transition temperature (Tg)48多孔\少孔Extra/Missing Hole49硬化剂hardener50空气滤清器\过滤器hepa filter1规范specification\standard2铣靶spot face3衝压\钢印stamping4标准液压法standard hydraulic lamination 5缺胶starvation6应力\应度strain7应力计stress meter8板面突起surface convex\swelling9板面检查surface examination10板面粗糙度surface roughness11热震荡试验thermal shock12厚度不均uneven thickness distribution 13抗污抗氧化剂tarnish and oxide resist14透光度transmittance15裁切线trim line16测试undercut17万用型universal18有形库存visible inventory19仓库warehouse20湿化学制程wet chemistry process21灯芯\渗铜wicking22纵横比width-to-thickness ratio23良率yield24点灯次数Times of Light switch25真空延迟时间Vacuum delayed time26+/-2 周The front or rear two weeks 27无尘室clean room28上喷压Upper spray pressure29下喷压Lower spray pressure30显影剂developer31主轴转速(RPM) Spindle Revolution Speed\Revolution PerMinute RPM32光电耦合器(Charge Couple Device) CCD3390° 孔切破90 degree breakage34缺点侦测\检测defect detection35聚焦focus36光校正calibration37极性Polarity38正极\阳极Positive39负极\阴极Negative40下钻点\下刀点entry41量杯measuring cup42微切片Microsection43爆孔hole breakout(鑽孔)\hole overflow(防焊油墨)44温差temperature difference45文字不清marking(symbol) blurred46文字白点S/L white point47补充显影additional developing48烘烤baking49确认检修系统Visual Repair System(VRS)50图表Diagram1腐蚀Corrosive2致癌物carcinogenic3有机体突变的Mutagenic4染色体错位chromosome aberration5畸形teratogenic6有害气体poisonous gas7易燃性Inflammability8爆炸性explosion9吸入\吸入剂inhalation10护目镜goggle11棉手套Cotton glove12化学特性Chemical properties13熔点Melting point14抽样检查spot check15沸水boiling water16冲模Punching17氢溴化物hydrochloride18醇\酒精alcohol19持续改进continual improvement20纠正措施corrective action21环境因素\影响\方针environment aspect\impact\policy22环境管理体系environment management system23污染预防prevention of pollution24品质关键点critical to quality(CTQ)25客户需求分析Customer Needs Mapping(CNM)26质量功能分布Quality Function Deployment(QFD)27失效模式及后果分析Failure Mode & Effects Analysis(FMEA) 28跨功能小组Cross-functional involvement29传感器sensor30点阵图tally chart31全面品质管理Total Quality Management(TQM)如QC七大手法32柏拉图Pareto Chart33因果图\鱼骨图Cause and Effect diagrams34脑力激荡Brainstorming35散布图Scatter diagrams36全面设备保养Total Productive Maintenance(TPM)37控制图Conttrol Chart38测定系统分析Gage Repeatability&Reproducibility(GRR) 39印制电路板协会Institute of printed circuit(IPC)40有机保焊膜Organic Solderability Preservative(OSP) 41进刀Feed42金盐Potassium Gold Cyanide(金氰化鉀PGC)43辐射式红外线焊接Radiation(輻射) Infrared Rays(IR)Reflow(焊接)44锡膏熔焊Reflow Soldering45缩锡Dewetting46锡炉浮渣Dross47锡尖Solder Icicle48锡球Solder Ball49电容器capacitor50波峰焊Wave Soldering1石油petroleum2线圈\缠绕coil3代理商agency4自由基Free Radical5镀金Golden Plating6防焊阻剂Polymer coating(solder resistent) 7内层(外层)孔环Internal(external) Annular ring8隧道式烤箱transmission toaster9直立式烤箱vertical toaster10光面\雾面油墨glossy\matte ink11晶片直接组装Chip On Board(COB)12组装密度packaging density13球状阵列Ball Grid Array(BGA)14焊膏solder paste\solder cream15焊料粉末(焊粉)solder powder16触变性thixotropy(粘度變化特性)17储存寿命shelf life18网版(脱网)高度snap off distance19拉丝stringing20平移偏差shifting deviation21贴装几Placement equipment22虚焊点(焊点不佳)colder solder connection23焊盘起翘lifted land24锡珠solder ball25波峰焊wave soldering26迴流焊reflow soldering27离子清洁度ion cleaning28印制电路元件printed circuit assembly(PCA)29特采Accept on Deviation\Use As It30首件检验报告First Piece Inspection Report31工序变更通知Process Chang Notice（PCN）32孔铜厚度Barrel Copper thickness\Hole CopperThickness33面铜厚度Surface Copper Thickness34皱折wrinkle35置信区间Confidence interval36相关性Correlation37相关矩阵Correlation Matrix38任意抽样法Haphazard Sampling39不合格品Nonconforming units40不合格Nonconformity41正态分布Normal Distribution42排列图(柏拉图)Pareto Chart43预测区间Prediction Interval44基于概率的控制图Probability Based Chart45制程能力Process Capability46二次函数Quadratic47随机抽样Random sampling48极差Range49合理子组Rational Subgroup50回归控制图Regression control chart1故障failure\breakdown2夹头grip holder3解析度\解像度resolution4可靠度reliability5孔位错误(孔偏)mis hole location6孔径\钻孔直径错误Hole Diameter error7离子污染度试验ionic contamination testing8线距line space9线宽line width\trace width10感光油墨liquid photoimageable solder resist ink 11批batch\lot12 裂痕\白斑\白点\白边crazing\mealing(白點)\Haloing(白邊)13对位不准misregistration14钉头nail heading15数位钻孔机NC drill16原稿底片original art work (A/W)17钻针重叠overlap18氧化oxidation19剥离\抗撕强度peel strength20感光起始剂photo initiator21凹陷dent22塞孔plug hole\stuffing23补线不良poor touch-up24循环周期Periodically cycle25初始资料protocal26喷砂pumice scrub27对位孔registration hole28文字印刷silk screen printing\printing of legend29胶渣resin smear30孔壁粗糙度roughtness31防焊文字S/L32毛边serrated edges 33跳印skip printing34漂锡solder float35喷涂spray coating36刮刀Squeegee37孔规taped hole gauge 38薄基板\内层板thin core39工作片工作母片working gerberworking master gerber40粗化abrade41电流密度Current Density42风刀Air Knife43获取资格的Qualify/qualified + n. or + to44现场locality(PD)45浓度偏低Conc. Lower46浓度偏高Conc. Higher47人员疏忽Operator careless48经纬向错误longitude and latitude contrary49上件不良failed componmt mounting50防呆孔Poka-Yoke hole\ mistake proofing hole1假性露铜unreal copper exposure2积墨ink accumulation3印偏ink printing deviated4遵照现场作业规范comply with the handling standardization 5放置时间Holding time6烘乾温度不足Insufficient in dry temperature7设备故障breakdown of machine8压膜滚轮 D/F laminated roller9sth. 受损或污染Damaged or contaminated10粘尘压力sticky pressure11曝光灯管exposure fluorescent tube12光阶 light step condition13曝偏Exposure misregistration14层间对准度alignment registration15吸气不良vacuum treatment abnormal16曝光藏点Exposure shelter17人员动作不当improper handling18显影Developing19蚀刻Etching20去膜stripping21Mylar 未撕Mylar non tearing off22教育训练instruction and trainning23进行显破点测试conduct developing point broken test 24喷压Spraying pressure25蚀刻不洁Etching incompletely\underetch26蚀刻液Etchants27首件确认First article confirm28电性不良Electrical performance defective29去膜不净Film stripping uncleanness 30几台漏测Equipment test leaking31领班Foreman32主管Chief33稳定性Stability34误判Misjudgement35混料Mixture36铝粉浓度(火山灰)Aluminum percentage37超音波测试(锡箔纸)Tin foil perforating test 38水破测试water broken test39油墨黏度ink viscosity40黏度计viscosimeter41数孔机hole counter42振动马达vibration motor43网版调偏net screen misregistration 44试印膜trial printing film45机台未清洁worktable uncleaness46万用塞孔垫板universal plugging back-up 47预烤Precure48上锡\焊锡性不良poor solderability49温度均匀性Temp. uniformability5010倍放大镜10X magnifier1捲尺measuring tape2千分尺micrometer3剥离强度Peeling strength4尺寸安定性Dimensional stability5有害物质Hazardous substance6元素分析仪 element analyzing instrument7显微镜microscope8游标卡尺vernier caliper9膜厚测量仪membrane thickness measuring intrument 10铣刀milling cutter\routing bit11钻针drill bit12化学元素chemical elements13化学药水chemical liquid14裁切刀具cutting tool15控制面板control panel16日点检表daily check list17光面油墨glossy green ink\resist(阻焊劑防染劑) 18公差\误差 tolerance\variance\bias(偏差)19量产mass production20白色文字white ident21成型外型routed outline22连片尺寸PNL drawing dimension23折断边break-away tabs24检查表inspection sheet25记录表data sheet\record chart26报表report forms27点检表Check list28磨边机Grind- edging machine\ Edger29打磨机polisher30板面光滑Board surface smooth31滴定法分析Titration analysis32温度计Temp. meter\Thermograph33压力计Pressure meter34能量格测试Energy-step tablet test35黏纸viscosity paper36六点测温仪Six points Temp. uniformability testInstrument37催化剂catalyst38稳定剂\安定剂stabilizer39硫酸铜回收机CuSO4 retrieve equipment40秒錶stopwatch41预热preheat42计时器chronograph\timepiece43能量计energy meter44靶孔机target hole equipment45铜含量The contents of Cu46液体比重计hydrometer47比重测定法stereometry48杀菌剂sterilant49蚀刻因子Etching factor\value\element50自动光学检测Automatical optical inspection(AOI)1精度Precision2栈板pallet3电动拖车\叉车electric trailer\fork lifter4针盘bit holder5放置架placement rack6静止消泡时间static\rest defoaming time7转板Transfer plate8水性笔Mark pen9尼龙\不织布\陶瓷nylon\non-woven fabric\ceramic10比色计chromo meter11湿度卡Humidity Indicator Cards12测温仪Thermoscope13龙门吊gantry crane14摇摆\摆动swing15PIN孔重合pin hole superposing16首躺first cycle17中和洗neutralization cleaning18流量flow amount19除胶速率desmear rate20湿润(电镀)moisten21获准供应商supplier warrant22供应商批准程序书Supplier Part Approval Process(SPAP) 23V-cut残厚Remain thickness of V-cut24冷媒油refrigerant oil25压力脚pressure foot26块规block gauge27高度规vernier height gage28金刚砂carborundum\Emery29火山灰volcanic ash30高阻计high resistance meter31模具图mold draw32支架Chassis33治具fixture34超音波浸洗ultrasonic dip35酸浸acid dipping36电流强度current amperage37化验分析表Assay analysis report forms38加压水洗Pressurized water rinsing39酸洗acid rinsing40溢流水洗cascade water rinsing\overflow 41沉淀缸sediment tank42冲污水waste water rinsing43水柱式冲洗Jet cleaning44高压水柱式冲洗High pressure rotating jet rinse 45清水洗Fresh water rinsing46干板组合Drying module47抗腐蚀测试accelerated corrosion test48速化反应acceleration49实际在制品active work in process50总量amount1高性能(电子)工业级high performance industrial2高延展性铜箔high temperature elongation copper(HTEC) 3高温树脂high temperature epoxy (HTE)4孔数hole number5哈氏槽hull cell6水解hydrolysis7改善方案implementation8努普(硬度单位)Knoop(Hardness)9牛皮纸kraft paper10压膜机laminator11刃角磨损lay back12牵引\定位螺丝lead screw13平整剂levelling additive14线性可变差动转换器linear variable differential transformer(LVDL)15 刷磨清洁法machine scrub16钻头刃带margin17主图\机构图master drawing18基材利用率material use factor19湿度与绝缘电阻测试moisture and insulation resistance test 20锯齿\蚀刻缺口mouse bite21负片negative film22结瘤\铜瘤nodule23流胶量百分比resin flow percentage24胶含量resin content25报废因素obsolescence factor26一铜panel plating27二铜pattern plating28透电率\介电常熟permittivity29极性吸引力polar-polar interaction30聚酯类polyester31孔变形poor drill32预聚合物prepolymer33原始资料protocal34喷砂清洁法pumice scrub35挂架rack36折光率refraction37对位元用标记register mark(對位點)38孔内沾文字S/L on hole39孔内防焊S/M on hole40干膜屑\透明残膜scum41漏印\跳印skip printing42表面附著元件SMD ( surface mount device )43表面附著技术SMT ( surface mount technology )44锡突solder bump45漂锡solder float46油墨附著力solder mask adhesion47金手指上锡solder on G/F48线路沾锡solder on trace49锡塞solder plug50统计制程管控SPC ( Statistical Process Control )1自检Self-examine2柠檬酸浓度Citric acid conc.3液位Liquid Level4析出物educt5垂直的perpendicular6喷砂能力pumice capability7阀门 Valve8外包加工contract-production9退货拒收REJ ( reject )10植PIN深度Depth of external pin11上PIN beat PIN12精确度Precision13准确度accuracy14操作员技术不娴熟operator technique unskilled 15套环深度depth of sleeve-ring16精修(成型)finely couting17漏钻\漏捞Leaking drilling\routing18多钻\多捞surplus drilling\routing19排屑chip load20排屑槽flute21蜂鸣器check beeper22建立档案资料(建档)Archive data building23合格qualified24电子称Electronic scale25封口时间sealing time26超出范围out of scope27微蚀速率Micro-etching ratio28变色\褪色discolor29破损breakage30电导率conductance ratio31履历表biographic sketch32公式formula33扩孔针reaming drill bit34电木板bakelite board35允收水准general criteria36理想状况Target Condition37模板\模具Template38基准孔reference holes39压敏开关Piezo-switch40指示灯indicator41直方图Histogram42并联导体parallel conductors43导体连接处area of adjacent conductors44金属导体Metal conductors45防焊侧露(焊垫\线路)Adjacent isolated lands or conductorsexposed46有害物质公约Restriction of Hazardous Substances(RoHS) 47预防措施Precaution48生物可降解Biodegradability49生态环境ecology50(垃圾\废弃物)处Disposal理1浸焊Immersion Soldering2焊接点Solder Joint3焊锡丝Solder Wire4待工温度Idle Temp.\+Time(空轉時間)5静电释放Electrostatic Discharge(ESD)6静电压力Electrostatic Overstress(ESO)7电阻係数Electrical Resistivity8内应力Internal Stress9导热係数Thermal Conductivity10磷含量Phosphorous11颗粒大小Grain Size(μm)12X光测量X-ray Diffraction13抗拉强度Tensil Strength(N/mm2)14介面化合物Intermstallic Compound(IMC)15贾凡尼效应Galvanic Effect(不同金屬電位差加速腐蝕)16高频信号High Frequency Signal17肌肤效应Skin Effect(高頻線路沿道題表面傳輸)18阻隔效应Barrier Effect(合金層可有效減低離子遷移度) 19银Silver20硫酸sulfuric acid21仪器Apparatus(測試用儀器)22抛光Polish23磨切片grind microsection24文件保存期限Documentation of age25内部管理政策Internal Policies26工资支付Salary payments27责任书Responsibility28法定最小年龄The legal minimum age29熟练\技能Facility30隐私权right to privacy31贪污\腐败corruption32有效日期valid period33温度循环实验Temperature Cycling Test(TCT)34热衝击实验Thermal Shock Test(TST)35离子迁移试验Electrochemical Migration Test(ECM) 36绝缘电阻试验Surface Insulation Resistance(SIR) 37阳极灯丝Conductive Anode Filament(CAF)38爆板popcorn39生产车间Fabricating Plant40吊车crane41危险物品hazardous substance42文字脱落symbol fading43锯齿Worm-Eaten-Crack44经纬方向Grain Direction45V-cut Slit46幻灯片slide47预算budget48运输工具transport49货物cargo50容器vessel。
PCB设计及制造术语大全(中英文对照)
线路板流程术语中英文对照流程简介：开料－－钻孔－－干膜制程－－压合－－减铜－－电镀－－塞孔－－防焊(绿漆/绿油) －－镀金－－喷锡－－成型－－开短路测试－－终检－－雷射钻孔a. 开料( cut lamination)a-1 裁板( sheets cutting)a-2 原物料发料(panel)(shear material to size)b. 钻孔(drilling)b-1 内钻(inner layer drilling )b-2 一次孔(outer layer drilling )b-3 二次孔(2nd drilling)b-4 雷射钻孔(laser drilling )(laser ablation )b-5 盲(埋)孔钻孔(blind & buried hole drilling)c. 干膜制程( photo process(d/f))c-1 前处理(pretreatment)c-2 压膜(dry film lamination)c-3 曝光(exposure)c-4 显影(developing)c-5 蚀铜(etching)c-6 去膜(stripping)c-7 初检( touch-up)c-8 化学前处理,化学研磨( chemical milling )c-9 选择性浸金压膜(selective gold dry film lamination)c-10 显影(developing )c-11 去膜(stripping )developing , etching & stripping ( des )d. 压合laminationd-1 黑化(black oxide treatment)d-2 微蚀(microetching)d-3 铆钉组合(eyelet )d-4 叠板(lay up)d-5 压合(lamination)d-6 后处理(post treatment)d-7 黑氧化( black oxide removal )d-8 铣靶(spot face)d-9 去溢胶(resin flush removal)e. 减铜(copper reduction)e-1 薄化铜(copper reduction)f. 电镀(horizontal electrolytic plating)f-1 水平电镀(horizontal electro-plating) (panel plating) f-2 锡铅电镀( tin-lead plating ) (pattern plating)f-3 低于1 mil ( less than 1 mil thickness )f-4 高于1 mil ( more than 1 mil thickness)f-5 砂带研磨(belt sanding)f-6 剥锡铅( tin-lead stripping)f-7 微切片( microsection)g. 塞孔(plug hole)g-1 印刷( ink print )g-2 预烤(precure)g-3 表面刷磨(scrub)g-4 后烘烤(postcure)h. 防焊(绿漆/绿油): (solder mask)h-1 c面印刷(printing top side)h-2 s面印刷(printing bottom side)h-3 静电喷涂(spray coating)h-4 前处理(pretreatment)h-5 预烤(precure)h-6 曝光(exposure)h-7 显影(develop)h-8 后烘烤(postcure)h-9 uv烘烤(uv cure)h-10 文字印刷( printing of legend )h-11 喷砂( pumice)(wet blasting)h-12 印可剥离防焊(peelable solder mask)i . 镀金gold platingi-1 金手指镀镍金( gold finger )i-2 电镀软金(soft ni/au plating)i-3 浸镍金( immersion ni/au) (electroless ni/au)j. 喷锡(hot air solder leveling)j-1 水平喷锡(horizontal hot air solder leveling)j-2 垂直喷锡( vertical hot air solder leveling)j-3 超级焊锡(super solder )j-4. 印焊锡突点(solder bump)k. 成型(profile)(form)k-1 捞型(n/c routing ) (milling)k-2 模具冲(punch)k-3 板面清洗烘烤(cleaning & backing)k-4 v型槽( v-cut)(v-scoring)k-5 金手指斜边( beveling of g/f)l. 开短路测试(electrical testing) (continuity & insulation testing) l-1 aoi 光学检查( aoi inspection)l-2 vrs 目检(verified & repaired)l-3 泛用型治具测试(universal tester)l-4 专用治具测试(dedicated tester)l-5 飞针测试(flying probe)m. 终检( final visual inspection)m-1 压板翘( warpage remove)m-2 x-out 印刷(x-out marking)m-3 包装及出货(packing & shipping)m-4 目检( visual inspection)m-5 清洗及烘烤( final clean & baking)m-6 护铜剂(entek cu-106a)(osp)m-7 离子残余量测试(ionic contamination test )(cleanliness test) m-8 冷热冲击试验(thermal cycling testing)m-9 焊锡性试验( solderability testing )n. 雷射钻孔(laser ablation)n-1 雷射钻tooling孔(laser ablation tooling hole)n-2 雷射曝光对位孔(laser ablation registration hole)n-3 雷射mask制作(laser mask)n-4 雷射钻孔(laser ablation)n-5 aoi 检查及vrs ( aoi inspection & verified & repaired)n-6 blaser aoi (after desmear and microetching)n-7 除胶渣(desmear)n-8 微蚀(microetching )pcb综合词汇中英文对照：1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外pcb原材料化学用语中英文对照：1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foilpcb线路设计词汇中英文对照：1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequencepcb线路板其他相关中英文对照：1、主面：primary side2、辅面：secondary side3、支撑面：supporting plane4、信号：signal5、信号导线：signal conductor6、信号地线：signal ground7、信号速率：signal rate8、信号标准化：signal standardization9、信号层：signal layer10、寄生信号：spurious signal11、串扰：crosstalk12、电容：capacitance13、电容耦合：capacitive coupling14、电磁干扰：electromagnetic interference15、电磁屏蔽：electromangetic shielding16、噪音：noise17、电磁兼容性：electromagnetic compatbility18、特性阻抗：impedance19、阻抗匹配：impedance match20、电感：inductance21、延迟：delay22、微带线：microstrip23、带状线：stripline24、探测点：probe point25、开窗口：cross hatching26、跨距：span27、共面性（度）：coplanarity28、埋入电阻：buried resistance29、黄金板：golden board30、芯板：core board31、薄基芯：thin core32、非均衡传输线：unbalanced transmission line33、阀值：threshold34、极限值：threshold limit value(tlv)35、散热层：heat sink plane36、热隔离：heat sink plane37、导通孔堵塞：via filiing38、波动：surge39、卡板：card40、卡板盒/卡板柜：card cages/card racks41、薄型多层板：thin type multilayer board42、埋/盲孔多层板：43、模块：module44、单芯片模块：single chip module (scm)45、多芯片模块：multichip module (mcm)46、多芯片模块层压基板：laminate substrate version of multichip module (mcm-l)47、多芯片模块陶瓷基数板：ceramic substrate version o fmultichip module (mcm-c)48、多芯片模块薄膜基板：deposition thin film substrate version of multilayer module (mcm-d)49、嵌入凸块互连技术：buried bump interconnection technology (b2 it)50、自动测试技术：automatic test equipment (ate)51、芯板导通孔堵塞：core board viafilling52、对准标记：alignment mark53、基准标记：fiducial mark54、拐角标记：corner mark55、剪切标记：crop mark56、铣切标记：routing mark57、对位标记：registration mark58、缩减标记：reduvtion mark59、层间重合度：layer to layer registration60、狗骨结构：dog hone61、热设计：thermal design62、热阻：thermal resistance线路板（pcb）常用度量衡单位术语换算1英尺=12英寸1英寸inch=1000密尔mil1mil=25.4um1mil=1000uin mil密耳有时也成英丝1um=40uin（有些公司称微英寸为麦，其实是微英寸）1oz=28.35克/平方英尺=35微米h=18微米4mil/4mil=0.1mm/0.1mm线宽线距1asd=1安培/平方分米=10.76安培/平方英尺1am=1安培分钟=60库仑主要用于贵金属电镀如镀金1平方分米=10.76平方英尺1盎司=28.35克,此为英制单位1加仑(英制)=4.5升1加仑美制=3.785升1kha=1000安小时1安培小时=3600库仑比重波美度=145-145/比重sg.sg.比重（克/立方厘米）=145/（145-波美度)pcb外观及功能性测试相关术语1.综合词汇1.1 as received 验收态提交验收的产品尚未经受任何条件处理,在正常大气条件下机械试验时阿状态1.2 production board 成品板符合设计图纸,有关规范和采购要求的,并按一个生产批生产出来的任何一块印制板1.3 test board 测试板用相同工艺生产的,用来确定一批印制板可接受性的一种印制板.它能代表该批印制板的质量。
pcb中英文术语对照
pcb中英文术语对照A/W (artwork) 底片Ablation 烧溶(laser),切除abrade 粗化abrasion resistance 耐磨性absorption 吸收ACC ( accept ) 允收accelerated corrosion test 加速腐蚀accelerated test 加速试验acceleration 速化反应accelerator 加速剂acceptable 允收activator 活化液active work in process 实际在制品adhesion 附着力adhesive method 黏着法air inclusion 气泡air knife 风刀amorphous change 不定形的改变amount 总量amylnitrite 硝基戊烷analyzer 分析仪anneal 回火annular ring 环状垫圈;孔环anode slime (sludge) 阳极泥anodizing 阳极处理AOI ( automatic optical inspection ) 自动:光学检测applicable documents 引用之文件AQL sampling 允收水准抽样aqueous photoresist 液态光阻aspect ratio 纵横比(厚宽比)As received 到货时back lighting 背光back-up 垫板banked work in process 预留在制品base material 基材baseline performance 基准绩效batch 批beta backscattering 贝他射线照射法beveling 切斜边;斜边biaxial deformation 二方向之变形black-oxide 黑化blank controller 空白对照组blank panel 空板blanking 挖空blip 弹开blister 气泡;起泡blistering 气泡blow hole 吹孔board-thickness error 板厚错误bonding plies 黏结层bow ; bowing 板弯break out 从平环破出bridging 搭桥;桥接BTO (Build To Order) 接单生产burning 烧焦burr 毛边(毛头)camcorder 一体型摄录放机carbide 碳化物carlson pin 定位梢carrier 载运剂catalyzing 催化catholic sputtering 阴极溅射法caul plate 隔板;钢板calibration system requirements 校验系统之各种要求center beam method 中心光束法central projection 集中式投射线certification 认证chamfer 倒角(金手指)chamfering 切斜边;倒角characteristic impedance 特性阻抗charge transfer overpotential 电量传递过电压chase 网框checkboard 棋盘chelator 蟹和剂chemical bond 化学键chemical vapor deposition 化学蒸着镀circumferential void 圆周性之孔破clad metal 包夹金属clean room 无尘室clearance 间隙coat 镀外表coating error 防焊覆盖错误coefficient of thermal expansion (CTE) 热澎胀系数cold solder joint 冷焊点cold-weld 金属粉末冷焊color 颜色color error 颜色错误compensation 补偿competitive performance 竞争力绩效complex salt 错化物complexor 错化物component hole 零件孔component side 零件面concentric 同心conformance 密贴性consumer products 消费性产品contact resistance 接触电阻continuous performance 连续发挥效能contract service 协力厂controlled split 均裂式conventional flow 乱流方式conventional tensile test 传统力测试法conversion coating 转化层convex 突出coordinate list 数据清单copper claded laminates (CCL) 铜箔基板copper exposure 线路露铜copper mirror 镜铜copper pad 铜箔圆配copper residue (copper splash) 铜渣corrosion rate numbering 腐蚀速率计数系统corrosion resistance 抗蚀性coulombs law 库伦定律countersink 喇叭孔coupon 试样coupon location 试样点covering power 遮盖力CPU 中央处理器crack 破裂;裂痕crazing 裂痕;白斑cross linking 交联聚合cross talk 呼应作用crosslinking 交联crystal collection 结晶收集curing 聚合体current efficiency 电流效率cut-outs 挖空cutting 裁板cyanide 氰化物cycles of learning 学习循环cycle-time reduction 交期缩短date code 周期deburring 去毛头dedicated 专用型degradation 退变delamination 分层dent / pin hole 凹陷/ 针孔department of defense 国防部designation 字码简示法de-smear 除胶渣developing 显影dewetting 缩锡dewetting time 缩锡时间dimension error 外形尺寸错误dielectric constant 介质常数difficulty 困难度difunctional 双功能dimension 尺寸dimension stability 尺寸安定性dimensional stability 尺度安定性dimension and tolerance 尺寸与公差dirty hole 孔异物discolor hole 孔黑;孔灰;氧化discoloration 变色disposable eyelet method 消耗性铆钉法distortion factor 尺寸变形函数double side 双面板downtime 停机时间drill 钻孔drill bit 钻头drill facet 钻尖切萷面drill pointer 钻尖重(研)磨机drilled blank board 已钻孔之裸板drilling 钻孔dry film 干膜ductility 延展性economy of scale 经济规模edge spacing 板边空地edge-board contact ( gold finger ) 金手指tab 金手指tack free 不黏taped hole gauge 锥形孔规target hole 靶孔task force 任务编组tensile strength 抗拉强度tensile stress 性应力tent 浮盖terms and definitions 术语与定义termination load 抗匹配负载test circuit 测试线路test method 试验方法test point 测试点thermal shock 热震荡试验thermal stress 热应力试验thermistor 热电感应式thermo cycling 热循环试验theoretical cycle time 理论性周期时间thickness 厚度time to market 上市时机thickness distribution 厚度分布thief 补助阴极thin core 薄基板;层板throwing power 分布力tolerance 公差;容差tooling hole 工具孔torque load 扭力拒之负载total quality program 全面的品质计划toughness 坚度trace error 线路错误trace nick & pin hole 线路缺口及针孔trace peeling 线路剥离trace pin-hole 线路针孔trace surface roughness 线路表面粗糙tarnish and oxide resist 抗污抗氧化剂transmittance 透光度trim line 裁切线true levelling 真平整true position 真正位置的孔;真位twist 板翘type 种类umbra 本影undercut 侧蚀uneven coating 喷锡厚镀不平整universal 万用型universal tensile tester 万用拉力试验机universal tester 泛用型测试机upper carrier 顶部承载钢uptime 稼动:时间vacuum deposition 真空蒸镀法vacuum hydraulic lamination真空液压法vaporizer 气化室V-cut V形槽vertical microsection 垂直微切片via hole 导通孔visible inventory 有形的库存vision inspection 目视检查Void 孔破void in hole 孔壁上的破洞void in PTH hole 孔破walkman 随身听warehouse 仓库warp 板弯warp , warpage 板弯water absorption 吸水性wear resistance 耐磨度weave exposure 纤纹显露weave texture 织纹隐现wedge angle 契尖角week 周wet chemistry 湿式化学制程wet film 湿膜wet lamination 湿膜压膜法wet process 湿制程wetting 沾锡wetting balance 沾锡平衡法wicking 渗铜;渗入;灯蕊效应width 宽度width reduce 线细width-to-thickness ratio 宽度与厚度的比值window 操作围work-in-process 在制品work order 工单working film 工作片working master 工作母片year 年yellow 金黄色yield 良率电路板门户网，商机无限，资讯最新，问答圈子，社区平台 jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:32:00第3楼fabric 网布failure 故障fast response 快速响应fault 瑕庛;缺陷fiber exposure 纤维显露fiber protrusion 纤维突出fiducial mark 光学点,基准记号filler 填充料film 底片filtration 过滤finished board 成品fixing 固着fixture 电测夹具(治具) flaking off 粹离flammability rating 燃性等级flare 喇叭形孔flat cable 并排电缆feedback loop 回馈循环first-in-first-out (FIFO) 先进先出flexible manufacturing system (FMS) 弹性制造系统flux 助焊剂foil distortion 铜层变形fold 空泡foreign include 异物foreign material 基材异物free radical chain polymerization 自由基连锁聚合fully additive 加成法fully annealed type 彻底回火轫化之类形function 函数fundamental and basic 基本fungus resistance 抗霉性funnel flange 喇叭形折翼galvanized 加法尼化制程gap 钻尖分开gauge length 有效长度gel time 胶化时间general resist ink 一般阻剂油墨general 通论general industrial 一般性(电子)工业级geometrical levelling 几何平整glass transition temperature (Tg) 玻璃态转换温度Gold 金gold finger 金手指gold plating 镀金golden board 标准板gouges 刷磨凹沟gouging 挖破grain boundary 金属晶体之四边green 绿色grip 夹头ground plane 接地层ground plane clearance 接地空环hackers 骇客HAL ( hot air leveling ) 喷锡haloing 白边;白圈hardener 硬化剂hardness 硬度hepa filter 空气滤清器high performance industrial 高性能(电子)工业级high reliability 高可靠度high resolution 高分辨率high temperature elongation (HTE) 高温延展性铜箔high temperature epoxy (HTE) 高温树酯hit 击hole counter 数孔机hole diameter 孔径hole diameter error 孔径错误hole location 孔位hole number 孔数hole wall quality 孔壁品质hook 外弧hot dip 热浸法hull cell 哈氏槽hybrid 混成集成电路hydrogen bonding 氢键hydrolysis 水解hydrometallurgy 湿法冶金法image analysis system 影像分析系统image transfer 影像转移immersion gold 浸金(化镍金)immersion plating 浸镀法impedance 阻抗infrared reflow 红外线重熔inhibitor 热聚合抑制剂injection mold 射模ink 油墨innerlayer & outlayer 外层insulation resistance 绝缘电阻intended position 应该在的位置intensifier 增强器intensity 强度inter molecular exchange 交互改变interconnection 互相连通ionic contaminants 离子性污染物ionic contamination testing 离子污染试验IPA 异丙醇5I : inspiration (启蒙)identification 确认计划目标implementation 改善方案information 数据internalization 制度化invisible inventory 无形的库存knife edges 刀缘Knoop 努普(硬度单位) kraft paper 牛皮纸laminar flow 层流laminate 基层板laminating 压合lamination 压合laminator 压膜机land 焊垫lay back 刃角磨损lay up 组合叠板layout 布线;布局lead screw 牵引螺丝leakage 漏电learning curve 学习曲线legend 文字标记leveling 平整levelling additive 平整剂levelling power 平整力life support 维系生命limiting current 极限电流line space 线距line width 线宽linear variable differential transformer(LVDL) 线性可变差动:转换器liquid 液状(态)liquid crystal resins 液晶树脂liquid photoimageable solder resist ink 液态感光防焊油墨liquid photoresist ink 液态光阻剂油墨lot size 批量lower carrier 底部承载板mechanical plating 机祴镀法machine scrub 刷磨清洁法macrothrowing power 巨分布力margin 钻头刃带market share 市场占有率marking error 文字错误masked leveling 儰装平整mass lamination 大型压板mass transfer 质量传送效应mass transfer overpotential 质量传递过电压mass transportation 质传master drawing 主图;蓝图material use factor 材料使用率mealing 泡点;白点memory 记忆装置meniscograph solderability measurement 新月型焊锡效果microetch 微蚀microetching 微蚀microfocus 微焦距microfocus system 微焦距系统microprofile 微表面microsectioning 微切片法microthrowing power 微分布力migration 迁移mini-tensile tester 迷你拉力测试仪mis hole location 孔位错误misregistration 焊锡面与零件面对位偏差misregsitration 对不准moisture and insulation resistance test 湿气与绝缘电阻试验molded circuit board (MCB) 模制电路板monoethanal amine 单乙醇氨monohydrate state 水化物monomer 单分子膜;单体mouse bite 锯齿;蚀刻缺口msec 毫秒muffle furnace 高温焚火炉multichip 超大IC型(多芯片模块)线路板流程术语中英文对照流程简介：开料－－钻孔－－干膜制程－－压合－－减铜－－电镀－－塞孔－－防焊(绿漆/绿油)－－镀金－－喷锡－－成型－－开短路测试－－终检－－雷射钻孔A. 开料( Cut Lamination)a-1 裁板( Sheets Cutting)a-2 原物料发料(Panel)(Shear material to Size)B. 钻孔(Drilling)b-1 钻(Inner Layer Drilling )b-2 一次孔(Outer Layer Drilling )b-3 二次孔(2nd Drilling)b-4 雷射钻孔(Laser Drilling )(Laser Ablation )b-5 盲(埋)孔钻孔(Blind & Buried Hole Drilling)C. 干膜制程( Photo Process(D/F))c-1 前处理(Pretreatment)c-2 压膜(Dry Film Lamination)c-3 曝光(Exposure)c-4 显影(Developing)c-5 蚀铜(Etching)c-6 去膜(Stripping)c-7 初检( Touch-up)c-8 化学前处理,化学研磨( Chemical Milling )c-9 选择性浸金压膜(Selective Gold Dry Film Lamination)c-10 显影(Developing )c-11 去膜(Stripping )Developing , Etching & Stripping ( DES )D. 压合Laminationd-1 黑化(Black Oxide Treatment)d-2 微蚀(Microetching)d-3 铆钉组合(eyelet )d-4 叠板(Lay up)d-5 压合(Lamination)d-6 后处理(Post Treatment)d-7 黑氧化( Black Oxide Removal )d-8 铣靶(spot face)d-9 去溢胶(resin flush removal)E. 减铜(Copper Reduction)e-1 薄化铜(Copper Reduction)F. 电镀(Horizontal Electrolytic Plating)f-1 水平电镀(Horizontal Electro-Plating) (Panel Plating) f-2 锡铅电镀( Tin-Lead Plating ) (Pattern Plating)f-3 低于1 mil ( Less than 1 mil Thickness )f-4 高于1 mil ( More than 1 mil Thickness)f-5 砂带研磨(Belt Sanding)f-6 剥锡铅( Tin-Lead Stripping)f-7 微切片( Microsection)G. 塞孔(Plug Hole)g-1 印刷( Ink Print )g-2 预烤(Precure)g-3 表面刷磨(Scrub)g-4 后烘烤(Postcure)H. 防焊(绿漆/绿油): (Solder Mask)h-1 C面印刷(Printing Top Side)h-2 S面印刷(Printing Bottom Side)h-3 静电喷涂(Spray Coating)h-4 前处理(Pretreatment)h-5 预烤(Precure)h-6 曝光(Exposure)h-7 显影(Develop)h-8 后烘烤(Postcure)h-9 UV烘烤(UV Cure)h-10 文字印刷( Printing of Legend )h-11 喷砂( Pumice)(Wet Blasting)h-12 印可剥离防焊(Peelable Solder Mask)I . 镀金Gold platingi-1 金手指镀镍金( Gold Finger )i-2 电镀软金(Soft Ni/Au Plating)i-3 浸镍金( Immersion Ni/Au) (Electroless Ni/Au) J. 喷锡(Hot Air Solder Leveling)j-1 水平喷锡(Horizontal Hot Air Solder Leveling)j-2 垂直喷锡( Vertical Hot Air Solder Leveling)j-3 超级焊锡(Super Solder )j-4. 印焊锡突点(Solder Bump)K. 成型(Profile)(Form)k-1 捞型(N/C Routing ) (Milling)k-2 模具冲(Punch)k-3 板面清洗烘烤(Cleaning & Backing)k-4 V型槽( V-Cut)(V-Scoring)k-5 金手指斜边( Beveling of G/F)L. 开短路测试(Electrical Testing) (Continuity & Insulation Testing) l-1 AOI 光学检查( AOI Inspection)l-2 VRS 目检(Verified & Repaired)l-3 泛用型治具测试(Universal Tester)l-4 专用治具测试(Dedicated Tester)l-5 飞针测试(Flying Probe)M. 终检( Final Visual Inspection)m-1 压板翘( Warpage Remove)m-2 X-OUT 印刷(X-Out Marking)m-3 包装及出货(Packing & shipping)m-4 目检( Visual Inspection)m-5 清洗及烘烤( Final Clean & Baking)m-6 护铜剂(ENTEK Cu-106A)(OSP)m-7 离子残余量测试(Ionic Contamination Test )(Cleanliness Test) m-8 冷热冲击试验(Thermal cycling Testing)m-9 焊锡性试验( Solderability Testing )N. 雷射钻孔(Laser Ablation)N-1 雷射钻Tooling孔(Laser ablation Tooling Hole)N-2 雷射曝光对位孔(Laser Ablation Registration Hole)N-3 雷射Mask制作(Laser Mask)N-4 雷射钻孔(Laser Ablation)N-5 AOI 检查及VRS ( AOI Inspection & Verified & Repaired)N-6 Blaser AOI (after Desmear and Microetching)N-7 除胶渣(Desmear)N-8 微蚀(Microetching )专业线路板厂ＣＡＭ及ＭＩ工程师培训，热线报名:05廖小姐jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:35:00第5楼PCB综合词汇中英文对照：1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer print ed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark中国新柳电子开发专业PCB线路设计：02(设计基地)() Email: jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:35:00第6楼1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制层覆箔板：mass lamination panel19、层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/pa per ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/pape r ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外专业线路板厂ＣＡＭ及ＭＩ工程师培训，热线报名:05廖小姐jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:36:00第7楼PCB原材料化学用语中英文对照：1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil中国PCB人才网，提供最全面的PCB专业人才信息，.pcbjob.jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:36:00第8楼PCB线路设计词汇中英文对照：1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence中国PCB人才网，提供最全面的PCB专业人才信息，.pcbjob.jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:37:00第9楼PCB线路板其他相关中英文对照：1、主面：primary side2、辅面：secondary side3、支撑面：supporting plane4、信号：signal5、信号导线：signal conductor6、信号地线：signal ground7、信号速率：signal rate8、信号标准化：signal standardization9、信号层：signal layer10、寄生信号：spurious signal11、串扰：crosstalk12、电容：capacitance13、电容耦合：capacitive coupling14、电磁干扰：electromagnetic interference15、电磁屏蔽：electromangetic shielding17、电磁兼容性：electromagnetic compatbility18、特性阻抗：impedance19、阻抗匹配：impedance match20、电感：inductance21、延迟：delay22、微带线：microstrip23、带状线：stripline24、探测点：probe point25、开窗口：cross hatching26、跨距：span27、共面性（度）：coplanarity28、埋入电阻：buried resistance29、黄金板：golden board30、芯板：core board31、薄基芯：thin core32、非均衡传输线：unbalanced transmission line33、阀值：threshold34、极限值：threshold limit value(TLV)35、散热层：heat sink plane36、热隔离：heat sink plane37、导通孔堵塞：via filiing39、卡板：card40、卡板盒/卡板柜：card cages/card racks41、薄型多层板：thin type multilayer board42、埋/盲孔多层板：43、模块：module44、单芯片模块：single chip module (SCM)45、多芯片模块：multichip module (MCM)46、多芯片模块层压基板：laminate substrate version of multichip module (MCM-L)47、多芯片模块瓷基数板：ceramic substrate version o fmultichip module (MCM-C)48、多芯片模块薄膜基板：deposition thin film substrate version of multilayer mod ule (MCM-D)49、嵌入凸块互连技术：buried bump interconnection technology (B2 it)50、自动测试技术：automatic test equipment (ATE)51、芯板导通孔堵塞：core board viafilling52、对准标记：alignment mark53、基准标记：fiducial mark54、拐角标记：corner mark55、剪切标记：crop mark56、铣切标记：routing mark57、对位标记：registration mark58、缩减标记：reduvtion mark59、层间重合度：layer to layer registration60、狗骨结构：dog hone61、热设计：thermal design62、热阻：thermal resistance翱世电子科技，为您提供芯片采购、PCB设计、打样贴片一体化服务！jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:38:00第10楼线路板（PCB）常用度量衡单位术语换算1英尺=12英寸1英寸inch=1000密尔mil1mil=25.4um1mil=1000uin mil密耳有时也成英丝1um=40uin（有些公司称微英寸为麦，其实是微英寸）1OZ=28.35克/平方英尺=35微米H=18微米4mil/4mil=0.1mm/0.1mm线宽线距1ASD=1安培/平方分米=10.76安培/平方英尺1AM=1安培分钟=60库仑主要用于贵金属电镀如镀金1平方分米=10.76平方英尺1盎司=28.35克,此为英制单位1加仑(英制)=4.5升1加仑美制=3.785升1KHA=1000安小时1安培小时=3600库仑比重波美度=145-145/比重SG.SG.比重（克/立方厘米）=145/（145-波美度)翱世电子科技，为您提供芯片采购、PCB设计、打样贴片一体化服务！jewwww等级：一级普工文章：46积分：419注册：2006年9月20日发表于2006-9-21 21:38:00第11楼PCB外观及功能性测试相关术语1.综合词汇1.1 as received 验收态提交验收的产品尚未经受任何条件处理,在正常大气条件下机械试验时阿状态1.2 production board 成品板符合设计图纸,有关规和采购要求的,并按一个生产批生产出来的任何一块印制板1.3 test board 测试板用相同工艺生产的,用来确定一批印制板可接受性的一种印制板.它能代表该批印制板的质量1.4 test pattern 测试图形用来完成一种测试用的导电图形.图形可以是生产板上的一部分导电图形或特殊设计的专用测试图形,这种测试图形可以放在附连测试板上液可以放在单独的测试板上(coupon)1.5 composite test pattern 综合测试图形两种或两种以上不同测试图形的结合,通常放在测试板上1.6 quality conformance test circuit 质量一致性检验电路在制板包含的一套完整的测试图形,用来确定在制板上的印制板质量的可接受性1.7 test coupon 附连测试板质量一致性检验电路的一部分图形,用于规定的验收检验或一组相关的试验1.8storage life 储存期2外观和尺寸2.1 visual examination 目检用肉眼或按规定的放大倍数对物理特征进行的检查2.2 blister 起泡基材的层间或基材与导电箔之间,基材与保护性涂层间产生局部膨胀而引起局部分离的现象.它是分层的一种形式2.3 blow hole 气孔由于排气而产生的孔洞2.4 bulge 凸起由于部分层或纤维与树脂分离而造成印制板或覆箔板表面隆起的现象2.5 circumferential separation 环形断裂一种裂缝或空洞.它存在于围绕镀覆孔四周的镀层,或围绕引线的焊点,或围绕空心铆钉的焊点,或在焊点和连接盘的界面处2.6 cracking 裂缝金属或非金属层的一种破损现象,它可能一直延伸到底面.2.7 crazing 微裂纹存在于基材的一种现象,在织物交织处,玻璃纤维与树脂分离的现象.表现为基材表面下出现相连的白色斑点或十字纹,通常与机械应力有关2.8 measling 白斑发生在基材部的,在织物交织处,玻璃纤维与树脂分离的现象,表现位在基材表面下出现分散的白色斑点或十字纹,通常与热应力有关2.9 crazing of conformal coating 敷形涂层微裂纹敷形涂层表面和部呈现的细微网状裂纹2.10 delamination 分层绝缘基材的层间,绝缘基材与导电箔或多层板任何层间分离的现象。
中英文对照的PCB专业用语 英语
一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electric-conductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminateadmin2007-03-30 15:525、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-cladlaminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates(epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binderadmin2007-03-30 15:5230、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)admin2007-03-30 15:5327、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referanc。
PCB专业术语中英文翻译
PCB专业术语中英文翻译很多PCB的书上使用的是英文，但是大多数的人又看不懂英文，这时候怎么办呢，我们需要翻译，但是如果每看到一个不会的词儿就去翻译，那么就太耗费时间了，所以我们捷多邦总结了一些常用的专业术语的中英文对照，希望能对大家有用。
1.印制电路：printed circuit2.印制线路：printed wiring3.印制板：printed board4.印制板电路：printed circuit board (pcb)5.印制线路板：printed wiring board(pwb)6.印制元件：printed component7.印制接点：printed contact8.印制板装配：printed board assembly9.板：board 110.表面层合电路板：surface laminar circuit (slc)11.埋入凸块连印制板：b2it printed board12.多层膜基板：multi-layered film substrate(mfs)13.层间全内导通多层印制板：alivh multilayer printed board14.载芯片板：chip on board (cob)15.埋电阻板：buried resistance board16.母板：mother board17.单面印制板：single-sided printed board(ssb)18.双面印制板：double-sided printed board(dsb)19.多层印制板：mulitlayer printed board(mlb)20.多层印制电路板：mulitlayer printed circuit board21.多层印制线路板：mulitlayer prited wiring board22.刚性印制板：rigid printed board23.刚性单面印制板：rigid single-sided printed borad24.刚性双面印制板：rigid double-sided printed borad25.刚性多层印制板：rigid multilayer printed board26.子板：daughter board27.背板：backplane28.裸板：bare board29.键盘板夹心板：copper-invar-copper board30.动态挠性板：dynamic flex board31.静态挠性板：static flex board32.可断拼板：break-away planel33.电缆：cable34.挠性扁平电缆：flexible flat cable (ffc)35.薄膜开关：membrane switch36.混合电路：hybrid circuit37.厚膜：thick film38.厚膜电路：thick film circuit39.薄膜：thin film40.挠性多层印制板：flexible multilayer printed board41.挠性印制板：flexible printed board42.挠性单面印制板：flexible single-sided printed board43.挠性双面印制板：flexible double-sided printed board44.挠性印制电路：flexible printed circuit (fpc)45.挠性印制线路：flexible printed wiring46.刚性印制板：flex-rigid printed board, rigid-flex printedboard47.刚性双面印制板：flex-rigid double-sided printed board,rigid-flex double-sided printed48.刚性多层印制板：flex-rigid multilayer printed board,rigid-flex multilayer printed board49.齐平印制板：flush printed board50.金属芯印制板：metal core printed board51.金属基印制板：metal base printed board52.多重布线印制板：mulit-wiring printed board53.陶瓷印制板：ceramic substrate printed board54.导电胶印制板：electroconductive paste printed board55.模塑电路板：molded circuit board56.模压印制板：stamped printed wiring board57.顺序层压多层印制板：sequentially-laminated mulitlayer58.散线印制板：discrete wiring board59.微线印制板：micro wire board60.积层印制板：buile-up printed board61.积层多层印制板：build-up mulitlayer printed board (bum)62.积层挠印制板：build-up flexible pr上面是一些比较常见的专业用语，有一些不是特别常用的有时候我们也会遇到，所以我们捷多邦也总结了一些不怎么常用的中英文对照，希望对你来说是有用的：1.Absorption 吸收、吸入2.Accelerated Test（Aging）加速试验、加速老化3.Accelerator 加速剂、速化剂4.Accept/Acceptance 允收5.Acceptable Quality Level（AQL）允收品质水准6.Accuracy 准确度ACF：7.Adhesive copper foil 有胶铜箔8.Activator 活化剂、添加剂比称为9.Activator Active parts（Devices）主动零件，指积体电路或电晶体10.Addition Agent 添加剂11.Additive Process 加成法、分全加成、半加成及部份加成12.Back Light（Back Lighting）背光法13.Back-UP 垫板14.Backpanels/ Backplanes 背板、支持板，厚度较厚，15.Ball Grid Array（BGA）球脚车列（封装）16.Barrel 孔壁17.Base Material 基材18.Batch 批（同时间发料某一数量的板子）19.Bevelling 切斜边20.Binder 黏结剂21.Capacitance 电容22.Carbide 碳化物、碳化钨钻头23.CAR: Corrective Action Report 改善报告24.Carbon Treatment 活性碳处理25.Card 卡板26.Carrier 载体27.Cartridge 滤芯28.Cathode 阴极L: Copper Clad Laminates 铜箔基板30.Ceramics 陶瓷31.Certificate 证明书32.CFC 氟氯碳化物33.Chloro-Fluoro-Carbon Chamfer 倒角、去掉直角34.Characteristic Impedance 特性阻抗35.Cheek list 检察清单36.Chip 晶粒、晶片37.Chip On Board 晶片黏著板38.Clean Room 无尘室(Class 100)39.Cleanliness 清洁度40.Clearance 余隙、余环41.COB（Chip on Board）晶片在板上直接组装42.COC（Certificate of Compliance）出货合格书。
中英文对照PCB生产流程常用术语
中英文对照PCB生产流程常用术语PCB（Printed Circuit Board）是电子产品中不可缺少的组成部分之一，其生产流程中涉及到许多常用术语。
以下是PCB生产流程常用术语的中英文对照：1. Substrate 基板2. Copper foil 铜箔3. Etching 蚀刻4. Resist 前刻蚀剂5. Photolithography 光刻6. Exposure 曝光7. Development 显影8. Plating 镀金9. Solder mask 焊膜10. Screen printing 丝网印刷11. Drilling 钻孔12. Plated through hole (PTH) 镀孔14. Surface mount technology (SMT) 表面贴装技术15. Solder paste 焊膏16. Reflow soldering 回流焊接17. Wave soldering 浪涌焊接18. Automated optical inspection (AOI) 自动光学检测19. Flying probe testing 飞针测试20. Automated X-ray inspection (AXI) 自动X射线检测21. Printed circuit assembly (PCA) 印刷电路组装23. Pick and place machine 取放机24. Reflow oven 回流炉25. Wave soldering machine 浪涌焊接机26. Conformal coating 敷膜27. Inspection 检查28. Testing 测试29. Quality control 质量控制30. Failure analysis 故障分析31. Rework 修复32. Final inspection 最终检验33. Packaging 包装34. Shipping 出货35. Documentation 文件以上是PCB生产流程中常用的术语，为了有效沟通和交流，在工作中我们要熟悉这些术语的中英对照。
PCB专业术语中英文汇总
中文
代码
英文名称
图形电镀去膜
SAP
Stripping after Pattern Plating
退锡
TSR
Tin Stripping
蚀刻/退锡
ETS
Etching, Tin Stripping
去膜/蚀刻/退锡
SES
DF Stripping, Etching, Tin Stripping
AOI：AOI
中文
代码
英文名称
外层离线AOI
OOA
Outer Offline AOI
外层AOI
OAO
Outer AOI
层间对准度测试1
QRE1
IPQC for Registration 1
外层VRS
OVR
Outer VRS
MASKAOI
MAO
Mask AOI
填孔AOI
SAO
Solid Via Filling Plating AOI
减铜干膜曝光
DER
D/F Exposuring before Copper Reduction
减铜干膜显影
DDR
D/F Development before Copper Reduction
减铜干膜LDI
DDC
D/F Laser Direct Image before Copper Reduction
脉冲全板电镀
PPP
Pulse Panel Plating
POFV沉铜
PBP
PTH before POFV
POFV电镀
POFV
Plate over Filling Via
全板电镀
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Adhesion 附着力Annular Ring 孔环AOI（automatic optical inspection）自动光学检测AQL（acceptable quality level）可接受的质量等级B²it(buried bump interconnection technology) 埋入凸块焊点互连技术BBH(buried blind hole) 埋盲孔BGA(ball grid array) 球栅阵列Blister 起泡Board Edges 板边Burr 毛头/毛刺BUM(Build-up multilayer) 积层式多层板BVH（buried/blind via hole）埋/盲导通孔CAD(computer aided design) 计算机辅助设计CAM(computer aided manufacturing) 计算机辅助制造Carbon oil 碳油CEM(composite epoxy material) 环氧树脂复合板材chamfer 倒角Characteristic impedance 特性阻抗CNC（computerized numerical control）计算机化数字控制Conductor Crack 导体破裂Conductor Spacing 导线间距connector 连接器Copper foil 铜箔（皮）Crazing 微裂纹(白斑)Delamination 分层Dewetting 半润湿(缩锡)DFM（design for manufacturing）可制造性设计DIP(dual in-line package) 双列直插式组件Dk（dielectric constant）介电常数DRC(design rule checking) 设计规则检查drawing 图纸ECN(engineering change notice) 工程更改通知ECO(engineering change order) 工程更改指令E glass 电子级玻璃entek OSP处理Epoxy resin 环氧树脂ESD(electrostatic discharge) 静电释放Etched Marking 蚀刻标记Flatness 翘曲度Foreign Inclusion 外来夹杂物Flame resistant 阻燃性FR-2(flame-retardant 2)耐燃酚醛纸基板FR-3(flame-retardant 3) 耐燃环氧纸基板FR-4(flame-retardant 4) 耐燃环氧玻璃布基板FR-5(flame-retardant 5) 耐燃多功能环氧玻璃布基板ground 地面（层）Haloing 晕圈HDI(high density interconnection) 高密度互连技术HASL(hot air solder leveling) 热风焊料整平（整平）IC(integrated circuits) 集成电路Ink Stamped Marking 盖印标记Insulation resistance 绝缘电阻Ion cleanliness 离子清洁度IPC(the institute for interconnecting and packaging of electronic circuits) 印制电路互连与封装协会ISO(International organization for standardization) 国际标准化组织Laminate Voids 压合空洞laser 激光LDI(laser direct imaging) 激光直接成像legend 文字标记、符号Lifted Lands 焊盘浮起logo 标志LPI(liquid photoimageable) 液态感光成像LPISM(liquid photoimageable solder mask) 液态感光阻焊膜marking 标记Measling 白斑Microvoids 微坑mil 密耳（千分之一英寸）MIL-STD(military standard) 美国军用标准Negative Etchback 欠蚀Nicks 缺口Nodules 镀镏Nonwetting 不润湿(拒锡)open 开路OSP(organic solderability preservatives) 表面抗氧化oxides 氧化物pad 焊盘panel 拼板pattern 板面图形PCB(printed circuit board) 印制电路板Pcs(pieces) 件、片、只Peeling 剥落pinhole 针孔Pink Ring 粉红圈Pits 凹坑pitch 中心距Plating Voids 镀层破洞plug 塞Positive Etchback 过蚀power 电源层prepreg 半固化片PTFE(polytetrafluoroethylene) 聚四氟乙烯PTH(plated through-hole) 金属化孔PWB(printed-wiring board) 印制线路板Registration 对准QA(quality assurance) 质量保证QC(quality control) 质量控制QE(quality engineering) 质量工程QFP(quad flat package) 方形扁平组件repair 修理RCC(resin coated copper) 已涂覆树脂的铜箔Reference dimension 参考尺寸registration 对准度resin 树脂rejection 拒收revision 修订版RF(radio frequency) 射频Ripples 纹路rout 外形铣scratch 划伤Screened Marking 纲印标记scoring 刻槽short 短路signal 信号Silk screen 丝网Skip Coverage 漏印slot 开槽SMD(surface mount device) 表面安装器件SMOBC(solder mask over bare copper) 裸铜覆盖阻焊膜SMT(surface mount technology) 表面安装技术smear 毛刺solder 焊锡S/M(solder mask) 绿油solderability 可焊性Soda Strawing (汽水)吸管式浮空SPC（statistical process control）统计过程控制spacing 间距Tape test 胶带实验TCE（thermal coefficient of expansion）热胀系数TDR（time-domain reflectometry）时域反射测试tolerance 公差Tenting 盖孔Texture Condition 显布纹Tg(glass transition temperature) 玻璃软化温度THT(through hole technology) 通孔（插装）技术trace 线路（条）UL(underwriters laboratories) 安全实验所NPTH 非金属化孔UV(ultraviolet) 紫外线辐射v-cut V刻Via hole 导通孔（过线孔）void 空洞warp 板弯Waves 波浪Weave Exposure 露织物wetting 沾锡Wicking 灯芯效应（渗铜）Wrinkles 起皱五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：rectangle pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、 v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance。