以太网交换机使用说明书
SIMATIC NET 工业以太网交换机 SCALANCE XC-200 操作说明说明书
![SIMATIC NET 工业以太网交换机 SCALANCE XC-200 操作说明说明书](https://img.taocdn.com/s3/m/abf137933086bceb19e8b8f67c1cfad6195fe92b.png)
SIMATIC NET工业以太网交换机SCALANCE XC-200操作说明02/2023法律资讯警告提示系统为了您的人身安全以及避免财产损失,必须注意本手册中的提示。
人身安全的提示用一个警告三角表示,仅与财产损失有关的提示不带警告三角。
警告提示根据危险等级由高到低如下表示。
危险表示如果不采取相应的小心措施,将会导致死亡或者严重的人身伤害。
警告表示如果不采取相应的小心措施,可能导致死亡或者严重的人身伤害。
小心表示如果不采取相应的小心措施,可能导致轻微的人身伤害。
注意表示如果不采取相应的小心措施,可能导致财产损失。
当出现多个危险等级的情况下,每次总是使用最高等级的警告提示。
如果在某个警告提示中带有警告可能导致人身伤害的警告三角,则可能在该警告提示中另外还附带有可能导致财产损失的警告。
合格的专业人员本文件所属的产品/系统只允许由符合各项工作要求的合格人员进行操作。
其操作必须遵照各自附带的文件说明,特别是其中的安全及警告提示。
由于具备相关培训及经验,合格人员可以察觉本产品/系统的风险,并避免可能的危险。
按规定使用 Siemens 产品请注意下列说明:警告Siemens 产品只允许用于目录和相关技术文件中规定的使用情况。
如果要使用其他公司的产品和组件,必须得到 Siemens 推荐和允许。
正确的运输、储存、组装、装配、安装、调试、操作和维护是产品安全、正常运行的前提。
必须保证允许的环境条件。
必须注意相关文件中的提示。
商标所有带有标记符号 ® 的都是 Siemens AG 的注册商标。
本印刷品中的其他符号可能是一些其他商标。
若第三方出于自身目的使用这些商标,将侵害其所有者的权利。
责任免除我们已对印刷品中所述内容与硬件和软件的一致性作过检查。
然而不排除存在偏差的可能性,因此我们不保证印刷品中所述内容与硬件和软件完全一致。
印刷品中的数据都按规定经过检测,必要的修正值包含在下一版本中。
Siemens AGDigital Industries Postfach 48 4890026 NÜRNBERG C79000-G8952-C442-14Ⓟ 02/2023 本公司保留更改的权利Copyright © Siemens AG 2016 - 2023.保留所有权利目录1简介 (7)2安全须知 (15)3安全建议 (17)4设备描述 (25)4.1产品总览 (25)4.2设备视图 (31)4.2.1SCALANCE XC206-2 (ST/BFOC) (31)4.2.2SCALANCE XC206-2 (SC) (32)4.2.3SCALANCE XC206-2G PoE (33)4.2.4SCALANCE XC206-2SFP (34)4.2.5SCALANCE XC208 (35)4.2.6SCALANCE XC208G PoE (36)4.2.7SCALANCE XC216 (37)4.2.8SCALANCE XC216-3G PoE (38)4.2.9SCALANCE XC216-4C (38)4.2.10SCALANCE XC224 (40)4.2.11SCALANCE XC224-4C (41)4.3附件 (41)4.4SELECT/SET 按钮 (47)4.5LED 指示灯 (49)4.5.1总览 (49)4.5.2“RM”LED (50)4.5.3“SB”LED (50)4.5.4“F”LED (50)4.5.5LED“DM1”和“DM2” (51)4.5.6LED“L1”和“L2” (51)4.5.7端口 LED (52)4.6C-PLUG (54)4.6.1C-PLUG 的功能 (54)4.6.2更换 C-PLUG (56)4.7组合端口 (57)4.8以太网供电 (PoE) (58)4.8.1符合标准的电源和电压范围 (58)4.8.2设备的 PoE 属性 (59)4.8.3电源传输和引脚分配 (30 W) (61)SCALANCE XC-200目录4.8.4电源传输和引脚分配 (60 W) (62)4.8.5组态 (62)5组装和拆卸 (63)5.1安装的安全注意事项 (63)5.2关于 SFP 收发器的一般说明 (66)5.3安装类型 (66)5.4在 DIN 导轨上安装 (67)5.4.1基于固定板的凹顶导轨安装 (67)5.4.2无固定板时的凹顶导轨安装 (69)5.5在标准 S7-300 导轨上安装 (70)5.5.1在带有固定板的标准导轨 S7-300 上安装 (70)5.5.2在不带固定板的标准导轨 S7-300 上安装 (71)5.6在标准导轨 S7-1500 上安装 (72)5.6.1在带有固定板的标准导轨 S7-1500 上安装 (72)5.6.2在不带固定板的标准导轨 S7-1500 上安装 (74)5.7基于固定板的墙式安装 (75)5.8更改固定销的位置 (76)5.9拆卸 (77)6连接 (79)6.1不使用 PoE 的设备的安全注意事项 (79)6.2PoE 设备的安全注意事项 (80)6.3有关在危险场所使用的安全注意事项 (82)6.4附加说明 (85)6.5接线规则 (86)6.624 V DC 电源 (87)6.754 V DC 电源 (88)6.8信号触点 (90)6.9功能性接地 (91)6.10串口 (92)6.11工业以太网 (94)6.11.1电气 (94)6.11.2光纤 (95)SCALANCE XC-200目录7维护和清洁 (97)8故障排除 (99)8.1使用 TFTP 下载新固件(无需 WBM 和 CLI) (99)8.2恢复出厂设置 (100)9技术规范 (101)9.1SCALANCE XC206-2 (ST/BFOC) 的技术规范 (101)9.2SCALANCE XC206-2 (SC) 的技术规范 (104)9.3SCALANCE XC206-2G PoE 的技术规范 (107)9.4SCALANCE XC206-2G PoE (54 V) 的技术规范 (110)9.5SCALANCE XC206-2G PoE EEC (54 V) 的技术规范 (113)9.6SCALANCE XC206-2SFP 的技术规范 (116)9.7SCALANCE XC206-2SFP G 的技术规范 (119)9.8SCALANCE XC206-2SFP EEC 的技术规范 (122)9.9SCALANCE XC206-2SFP G EEC 的技术规范 (125)9.10SCALANCE XC208 的技术规范 (128)9.11SCALANCE XC208G 的技术规范 (130)9.12SCALANCE XC208G PoE 的技术规范 (132)9.13SCALANCE XC208G PoE (54 V) 的技术规范 (134)9.14SCALANCE XC208EEC 的技术规范 (136)9.15SCALANCE XC208G EEC 的技术规范 (138)9.16SCALANCE XC216 的技术规范 (140)9.17SCALANCE XC216EEC 的技术规范 (142)9.18SCALANCE XC216-3G PoE 的技术规范 (144)9.19SCALANCE XC216-3G PoE (54 V) 的技术规范 (146)9.20SCALANCE XC216-4C 的技术规范 (150)9.21SCALANCE XC216-4C G 的技术规范 (153)9.22SCALANCE XC216-4C G EEC 的技术规范 (156)9.23SCALANCE XC224 的技术规范 (159)9.24SCALANCE XC224-4C G 的技术规范 (161)9.25SCALANCE XC224-4C G EEC 的技术规范 (164)9.26机械稳定性(运行时) (167)SCALANCE XC-200目录9.27射频辐射符合 NAMUR NE21 标准 (167)9.28电缆长度 (167)9.29交换特性 (168)10尺寸图 (171)11证书和认证 (179)索引 (189)SCALANCE XC-200简介1操作说明的用途这些操作说明适用于 SCALANCE XC-200 系列产品的安装和连接。
深瑞 PRS-7961A 工业以太网交换机 技术使用说明书
![深瑞 PRS-7961A 工业以太网交换机 技术使用说明书](https://img.taocdn.com/s3/m/46128f7cb207e87101f69e3143323968011cf43d.png)
安全使用须知
本产品在设计使用范围内具有良好可靠的性能,但需要避免人为对设备造成的损害或破 坏。使用设备前,请仔细阅读如下安全使用须知,以保障用户人身和设备的安全。阅读后请妥 善保管本说明书,以备将来参考。对于违反安全使用须知造成的人身伤害或设备损坏,我司不 承担任何责任。 不要将设备放置或安装在接近水源或潮湿的地方,保持设备周边的相对湿度在 5%~95%
7.1 调试口访问...................................................................................................20 7.2 Web 访问 ......................................................................................................22
免责声明:长园深瑞继保自动化有限公司竭力使本说明书中的信息尽可能准确、最新。然 而本公司不能保证本说明书完全没有任何技术错误或笔误,并保留在未通知用户的情况下对其 修改的权利。
保留所有权限:本说明书著作权属长园深瑞继保自动化有限公司所有。未经著作权人书面 许可,任何单位或个人不得以任何方式摘录、翻版、复制、翻译或者用于商业目的分发等行为。
4 安装...........................................................................................................9
4.1 尺寸图.............................................................................................................9 4.2 安装方式与步骤.............................................................................................9
瞻博网络(Juniper Networks)QFX5100以太网交换机产品说明说明书
![瞻博网络(Juniper Networks)QFX5100以太网交换机产品说明说明书](https://img.taocdn.com/s3/m/26cc111fbf23482fb4daa58da0116c175f0e1e0b.png)
Data SheetQFX5100 交换机型号QFX5100 系列产品包含四款紧凑型 1 U 型号和一款 2 U 型号,每个型号均提供线速数据包性能、超低延迟以及一组丰富的 Junos OS 功能。
除了高吞吐量数据包转发引擎 (PFE),具有 8 GB 内存和32 GB SSD 存储的强大 1.5 GHz 双核 Intel CPU 还进一步提升了所有 QFX5100 型号上运行的控制平面的性能。
QFX5100-48S:紧凑型 1 U 10GbE 数据中心接入交换机,带有 48个小型可插拔和可插拔增强型 (SFP/SFP+) 收发器端口和 6 个四路SFP+ (QSFP+) 端口,聚合吞吐量可达 1.44 Tbps 或者每台交换机的吞吐量可达 1.08 Bpps。
QFX5100-48T:紧凑型 1 U 10GbE 数据中心接入交换机,带有48 个三速 (10GbE/1GbE/100 Mbps) RJ-45 端口和 6 个 QSFP+ 端口,聚合吞吐量可达 1.44 Tbps 或每台交换机的吞吐量可达 1.08 Bpps。
QFX5100-24Q:紧凑型 1 U 高密度 40GbE 数据中心接入和聚合交换机,基础密度为 24 个 QSFP+ 端口,可选择使用两个四端口扩展模块扩展至 32 个 QSFP+ 端口。
全部 32 个端口都支持线速性能,聚合吞吐量可达 2.56 Tbps 或每台交换机的吞吐量可达 1.44 Bpps。
QFX5100-24Q-AA:紧凑型 1 U 高密度数据中心交换机,基础密度为 24 个 QSFP+ 端口。
通过添加可选的双宽 QFX-PFA-4Q 数据包流加速器 (PFA) 扩展模块,这款交换机可以变身为智能应用程序加速系统。
或者,通过安装两个四端口 40GbE 扩展模块,QFX5100-24Q-AA 可扩展为支持 32 个 QSFP+ 端口。
该交换机的CPU 子系统通过 32 GB DRAM 四核 Intel CPU 得以增强;通过板载 128 GB 固态驱动器还可以提供额外的存储容量。
以太网交换机 说明书
![以太网交换机 说明书](https://img.taocdn.com/s3/m/41a0891c227916888486d77a.png)
目录1.简介 (2)1.1 启封 (2)1.2 安装过程 (3)2 安装位置 (3)2.1 桌面或架上安装 (4)2.2 机架安装 (4)3. 连接交换机 (4)3.1 设备到交换机 (4)3.2 交换机/HUB到交换机 (5)3.3 应用示例 (6)4. 理解指示灯 (7)4.1 指示灯定义 (7)5. 故障处理 (8)5.1 故障原因 (8)附录A. 技术规范 (9)附录B. 电缆规格 (10)附录C. 电磁辐射及安全认证 (11)11.简介本交换机是一个具有16个10/100M口的即插即用的快速以太网交换机,该交换机具有速率自适应(10/100Mbps)和模式自探测(全双工或半双工),方便安装及使用,利用该交换机的交换技术每个网络连接可以使用高达200Mbps的带宽来传输数据,交换的总带宽为3.2Gbps.用户可以使用这种交换机改善他们的网络性能.1.1 启封一台16口10/100Mbps以太网交换机一条交流电源线两套机架支架和螺丝本用户手册21.2 安装过程2 安装位置本交换机可以放置在一个平面(如桌面)或机架上,为连接方便起见,交换机的放置应遵循以下原则:交换机放置应方便电缆的连接。
连接电缆应远离电源接口,及无线电、显示器等。
要保证交换机的放置位置有较好的通风环境(若环境温度超出0-40摄氏度温度范围,交换机将不能正常工作)。
32.1 桌面或架上安装1. 把要放置的第一台交换机放置在一个坚固的平面上.2. 把第二台交换机放置在第一台交换机上面,请不要在桌面上叠放超过3台交换机,以防摇动。
2.2 机架安装1. 利用支架和螺丝在机架安装。
2 使用十字螺丝起子固定交换机。
3. 连接交换机3.1 设备到交换机连接10 Base-T设备可使用3类或5类双绞线(管脚定义见附录B)连接100 Base-T设备可使用3类或5类双绞线(管脚定义见附录B)4最大电缆长度为100米(根据IEEE的规范)3.2 交换机/HUB 到交换机本交换机可以连接10/100Mbps交换机或HUB,连接方式如下: 3.2.1 MDI(级连口)口与MDI-X(非级连口)口的连接缆.线缆.53.3 应用示例交换机可以克服HUB-HUB的连接限制,改善网络的整体性能,交换机对传输网络中的数据包可以进行智能决策,所以交换机可以减少网络中的不必要的数据传输.下面示例显示交换机能够进行网络分段,减少网段中的节点数目减少冲突.64. 理解指示灯4.1 指示灯定义指示灯可以提供交换机及各端口状态等有用的信息指示灯 状态 说明电源灯 ON 交换机加电.显示模式绿色 指示灯指示Link / Act状态黄色 指示灯指示FDX / Col状态111-16口指示灯Link / Act状ON 端口有一个可靠的连接态闪烁 传送或接受数据.ON 全双工连接FDX / Col状态闪烁 冲突绿色 100Mbps连接黄色 10Mbps连接前面板有显示模式切换开关75. 故障处理5.1 故障原因交换机的故障一般有下列几种情况:设备没有加电错误的电缆连接交换端口无效注意:由于 Port 16 MDI-X 和 MDI port 共占用一个端口结构,不要同时使用两个端口。
H3C S2126-EI以太网交换机 操作手册(V1.02
![H3C S2126-EI以太网交换机 操作手册(V1.02](https://img.taocdn.com/s3/m/bd658de6910ef12d2bf9e705.png)
H3C S3600系列以太网交换机 操作手册-RELEASE 1510
![H3C S3600系列以太网交换机 操作手册-RELEASE 1510](https://img.taocdn.com/s3/m/68204be5102de2bd9605881b.png)
NTP 目录目录第1章 NTP配置.....................................................................................................................1-11.1 NTP简介.............................................................................................................................1-11.1.1 NTP的应用..............................................................................................................1-11.1.2 NTP工作原理...........................................................................................................1-21.1.3 NTP的工作模式.......................................................................................................1-31.2 配置NTP工作模式..............................................................................................................1-51.2.1 配置准备..................................................................................................................1-51.2.2 配置过程..................................................................................................................1-61.3 配置访问控制权限..............................................................................................................1-81.4 配置NTP验证功能..............................................................................................................1-81.4.1 配置准备..................................................................................................................1-81.4.2 配置过程..................................................................................................................1-91.5 配置NTP可选参数............................................................................................................1-111.6 NTP配置显示...................................................................................................................1-111.7 NTP典型配置举例............................................................................................................1-121.7.1 配置NTP服务器模式..............................................................................................1-121.7.2 配置NTP对等体模式..............................................................................................1-131.7.3 配置NTP广播模式..................................................................................................1-151.7.4 配置NTP组播模式..................................................................................................1-171.7.5 配置带身份验证的NTP服务器模式........................................................................1-19第1章 NTP配置1.1 NTP简介NTP(Network Time Protocol,网络时间协议)是由RFC1305定义的时间同步协议,用来在分布式时间服务器和客户端之间进行时间同步。
华为 Quidway S5700 系列以太网交换机 V100R005C01 说明书
![华为 Quidway S5700 系列以太网交换机 V100R005C01 说明书](https://img.taocdn.com/s3/m/8519d3e55ef7ba0d4a733b91.png)
Quidway S5700系列以太网交换机V100R005C01产品描述文档版本01发布日期2010-09-10华为技术有限公司版权所有 © 华为技术有限公司 2010。
保留一切权利。
非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部,并不得以任何形式传播。
商标声明和其他华为商标均为华为技术有限公司的商标。
本文档提及的其他所有商标或注册商标,由各自的所有人拥有。
注意您购买的产品、服务或特性等应受华为公司商业合同和条款的约束,本文档中描述的全部或部分产品、服务或特性可能不在您的购买或使用范围之内。
除非合同另有约定,华为公司对本文档内容不做任何明示或默示的声明或保证。
由于产品版本升级或其他原因,本文档内容会不定期进行更新。
除非另有约定,本文档仅作为使用指导,本文档中的所有陈述、信息和建议不构成任何明示或暗示的担保。
华为技术有限公司地址:深圳市龙岗区坂田华为总部办公楼邮编:518129网址:客户服务邮箱:support@客户服务电话:0755-******** 4008302118客户服务传真:0755-********Quidway S5700系列以太网交换机产品描述前言前言读者对象本文档针对S5700设备,介绍了产品定位和特点、产品架构、链路特性、业务特性、应用场景、操作和维护、技术指标。
本文档提供S5700设备的总体情况,便于读者全面了解产品特征。
本文档主要适用于以下工程师:l网络规划工程师l硬件安装工程师l调测工程师l数据配置工程师l现场维护工程师l网络监控工程师l系统维护工程师符号约定在本文中可能出现下列标志,它们所代表的含义如下。
修订记录修改记录累积了每次文档更新的说明。
最新版本的文档包含以前所有文档版本的更新内容。
文档版本 01 (2010-09-10)第一次正式发布。
前 言Quidway S5700系列以太网交换机产品描述Quidway S5700系列以太网交换机产品描述目录目录前言 (iii)1 产品定位和特点............................................................................................................................1-11.1 产品定位.........................................................................................................................................................1-21.2 产品特点.........................................................................................................................................................1-21.2.1 电信级的可维护性................................................................................................................................1-21.2.2 强大的多业务接入能力........................................................................................................................1-31.2.3 灵活的组网能力....................................................................................................................................1-31.2.4 网络级QoS保障...................................................................................................................................1-31.2.5 多层面的扩展能力................................................................................................................................1-31.2.6 周密的安全措施....................................................................................................................................1-31.2.7 便捷的操作维护....................................................................................................................................1-41.2.8 绿色节能设计........................................................................................................................................1-41.2.9 先进的防雷技术....................................................................................................................................1-41.2.10 人性化的PoE供电方式.....................................................................................................................1-42 产品架构........................................................................................................................................2-12.1 概述.................................................................................................................................................................2-22.2 整机结构.........................................................................................................................................................2-22.3 硬件模块.........................................................................................................................................................2-72.3.1 交换主控板............................................................................................................................................2-82.3.2 电源........................................................................................................................................................2-82.3.3 风扇........................................................................................................................................................2-82.3.4 插卡........................................................................................................................................................2-82.4 软件结构.........................................................................................................................................................2-93 链路特性........................................................................................................................................3-13.1 以太网特性.....................................................................................................................................................3-23.1.1 链路聚合................................................................................................................................................3-23.1.2 接口流控................................................................................................................................................3-23.1.3 流量抑制................................................................................................................................................3-23.1.4 VLAN.....................................................................................................................................................3-33.1.5 QinQ.......................................................................................................................................................3-53.2 STP/RSTP/MSTP............................................................................................................................................3-53.2.1 STP和RSTP.........................................................................................................................................3-53.2.2 MSTP.....................................................................................................................................................3-53.2.3 MSTP 保护功能....................................................................................................................................3-63.2.4 局部STP 和BPDU 隧道......................................................................................................................3-63.3 RRPP...............................................................................................................................................................3-73.3.1 RRPP 环网组成.....................................................................................................................................3-73.3.2 RRPP 工作机制.....................................................................................................................................3-73.3.3 多种拓扑结构........................................................................................................................................3-73.4 Smart Link.......................................................................................................................................................3-83.5 SEP..................................................................................................................................................................3-83.6 接口安全保护.................................................................................................................................................3-93.7 链路检测.........................................................................................................................................................3-94 业务特性........................................................................................................................................4-14.1 IPv4转发........................................................................................................................................................4-24.1.1 IPv4特性...............................................................................................................................................4-24.1.2 单播路由特征........................................................................................................................................4-24.1.3 组播路由特性........................................................................................................................................4-24.2 IPv6.................................................................................................................................................................4-34.3 路由协议.........................................................................................................................................................4-34.4 组播.................................................................................................................................................................4-34.4.1 IGMP Snooping......................................................................................................................................4-44.4.2 IGMP Proxy...........................................................................................................................................4-44.4.3 组播成员接口快速离开........................................................................................................................4-44.4.4 组播流量控制........................................................................................................................................4-44.4.5 跨VLAN 组播复制...............................................................................................................................4-44.4.6 可控组播................................................................................................................................................4-44.5 QoS..................................................................................................................................................................4-44.5.1 流分类....................................................................................................................................................4-54.5.2 访问控制和重标记................................................................................................................................4-54.5.3 流量监管................................................................................................................................................4-54.5.4 拥塞管理................................................................................................................................................4-64.5.5 拥塞避免................................................................................................................................................4-64.5.6 接口限速................................................................................................................................................4-64.5.7 支持双速三色........................................................................................................................................4-64.5.8 支持聚合CAR.......................................................................................................................................4-74.6 安全.................................................................................................................................................................4-74.6.1 设备的安全............................................................................................................................................4-74.6.2 业务的安全............................................................................................................................................4-84.6.3 安全认证................................................................................................................................................4-84.7 MAC 强制转发...............................................................................................................................................4-94.8 DHCP............................................................................................................................................................4-104.9 网络级可靠性...............................................................................................................................................4-104.9.1 MSTP 保护倒换..................................................................................................................................4-11目 录Quidway S5700系列以太网交换机产品描述Quidway S5700系列以太网交换机产品描述目录4.9.2 RRPP快速保护倒换...........................................................................................................................4-114.9.3 Smart Link双归属保护.......................................................................................................................4-114.9.4 以太网OAM........................................................................................................................................4-114.10 LLDP...........................................................................................................................................................4-124.11 NQA............................................................................................................................................................4-124.12 集群管理.....................................................................................................................................................4-124.13 堆叠.............................................................................................................................................................4-134.14 Web Server..................................................................................................................................................4-135 特性组网应用................................................................................................................................5-15.1 企业网络和园区网的汇聚.............................................................................................................................5-25.2 桌面终端接入.................................................................................................................................................5-25.3 iStack技术的应用..........................................................................................................................................5-35.4 作为小型企业的核心设备.............................................................................................................................5-46 操作维护和网管系统....................................................................................................................6-16.1 维护和管理.....................................................................................................................................................6-26.1.1 多种配置方式........................................................................................................................................6-26.1.2 监控和维护............................................................................................................................................6-26.1.3 诊断和调测............................................................................................................................................6-36.1.4 软件升级和热补丁................................................................................................................................6-46.1.5 硬件异常处理........................................................................................................................................6-46.2 U2000网管.....................................................................................................................................................6-46.2.1 网管组网方式........................................................................................................................................6-46.2.2 U2000网管站........................................................................................................................................6-57 系统技术指标................................................................................................................................7-17.1 物理参数.........................................................................................................................................................7-27.2 光模块属性.....................................................................................................................................................7-37.3 系统配置.........................................................................................................................................................7-57.4 软件特性列表.................................................................................................................................................7-6Quidway S5700系列以太网交换机产品描述插图目录插图目录图2-1 S5700-28C-EI-24S产品外观....................................................................................................................2-2图2-2 S5700-28C-EI产品外观...........................................................................................................................2-2图2-3 S5700-28C-PWR-EI产品外观.................................................................................................................2-3图2-4 S5700-28C-SI产品外观...........................................................................................................................2-3图2-5 S5700-52C-EI产品外观...........................................................................................................................2-4图2-6 S5700-52C-PWR-EI产品外观.................................................................................................................2-4图2-7 S5700-52C-SI产品外观...........................................................................................................................2-4图2-8 S5700-24TP-SI-AC产品外观...................................................................................................................2-5图2-9 S5700-24TP-SI-DC产品外观...................................................................................................................2-5图2-10 S5700-48TP-SI产品正面外观...............................................................................................................2-5图2-11 S5700-48TP-SI-AC产品背面外观.........................................................................................................2-5图2-12 S5700-48TP-SI-DC产品背面外观.........................................................................................................2-6图2-13 S5700-24TP-PWR-SI产品外观.............................................................................................................2-6图2-14 S5700-48TP-PWR-SI产品外观.............................................................................................................2-7图2-15 S5700硬件模块的逻辑结构..................................................................................................................2-7图4-1接入层连接示意图....................................................................................................................................4-9图5-1企业网络和园区网的接入........................................................................................................................5-2图5-2桌面终端接入............................................................................................................................................5-3图5-3 iStack技术的应用.....................................................................................................................................5-4图5-4作为小型企业的核心设备........................................................................................................................5-4Quidway S5700系列以太网交换机产品描述表格目录表格目录表7-1物理参数....................................................................................................................................................7-2表7-2 ESFP光模块(FE)的属性..........................................................................................................................7-3表7-3 ESFP光模块(GE)的属性....................................................................................................................7-4表7-4 ESFP光模块(CWDM彩光)的属性....................................................................................................7-4表7-5 SFP+光模块(10GE)的属性.................................................................................................................7-5表7-6系统配置....................................................................................................................................................7-5表7-7功能特性列表............................................................................................................................................7-6Quidway S5700系列以太网交换机产品描述 1 产品定位和特点1产品定位和特点关于本章1.1 产品定位1.2 产品特点1.1 产品定位Quidway S5700系列以太网交换机为A 类产品,在生活环境中,该产品可能会造成无线电干扰。
TO-LINK TL-SL1351 48+3G千兆以太网交换机 说明书
![TO-LINK TL-SL1351 48+3G千兆以太网交换机 说明书](https://img.taocdn.com/s3/m/3ab04c32eefdc8d376ee3299.png)
用户手册TL-SL135148+3G千兆以太网交换机Rev: 1.0.1声明Copyright © 2009 深圳市普联技术有限公司版权所有,保留所有权利未经深圳市普联技术有限公司明确书面许可,任何单位或个人不得擅自仿制、复制、誊抄或转译本书部分或全部内容。
不得以任何形式或任何方式(电子、机械、影印、录制或其他可能的方式)进行商品传播或用于任何商业、赢利目的。
为深圳市普联技术有限公司注册商标。
本文档提及的其他所有商标或注册商标,由各自的所有人拥有。
本手册所提到的产品规格和资讯仅供参考,如有内容更新,恕不另行通知。
除非有特殊约定,本手册仅作为使用指导,本手册中的所有陈述、信息等均不构成任何形式的担保。
目录物品清单 (1)第一章用户手册简介 (2)1.1 用途 (2)1.2 条款/使用方法 (2)1.3 用户手册概述 (2)第二章产品介绍 (3)2.1 产品概述 (3)2.2 性能特征 (3)第三章硬件安装 (5)3.1 安装在桌面上的方法 (5)3.2 安装在机架上的方法 (5)3.3 可选的SFP模块的安装.......................................................................3.4 初始化................................................................................................ 第四章外观部分指示说明..........................................................4.1 前面板................................................................................................4.2 后面板 (9)附录技术资料详细说明 (10)1物 品 清 单小心打开包装盒,检查包装盒里应有以下配件:一台TL-SL1351交换机一根交流电源线一本用户手册一张保修卡两个用来固定在机架上的L 型支架及其他配件如果发现有所损坏或有任何配件短缺的情形,请及时与当地经销商联系。
PCS-9882系列以太网交换机技术使用说明书
![PCS-9882系列以太网交换机技术使用说明书](https://img.taocdn.com/s3/m/e0ad70601ed9ad51f01df2a7.png)
2.1.2 机械特性 .............................................................................................................. 3
2.1.3 环境条件参数 ....................................................................................................... 3
第 3 章 硬件描述............................................................................................................................... 7
3.1 概述................................................................................................................................. 7
第 1 章 概述....................................................................................................... 1
1.1 应用................................................................................................................................. 1
深圳市讯记科技有限公司 CK2000 系列 V1.0 工业以太网交换机说明书
![深圳市讯记科技有限公司 CK2000 系列 V1.0 工业以太网交换机说明书](https://img.taocdn.com/s3/m/2b4703486d85ec3a87c24028915f804d2b1687ed.png)
脚 1、2、3、6 对应连接;对于交换机或集线器的 MDI-X 端口,采用的是交叉线:1→3、2→6、3→1、6→2。MDI/MDI-X 应用中的
http//:/
深圳市讯记科技有限公司 CK2000 系列 V1.0
CK2050
五电
五电,标准型工业以太网交换机,可选宽温(﹣40~+85)℃
单位 台 台 台 台
http//:/
【电源连接】
本设备支持双电源冗余输入,PWR1/PWR2 分别连接电源正(DC9~48V),COM 连接电源负,二路电源负极共用.
(标准型系列拨码)无功能
电源 1 正极 电源负,电源 1 和电源 2 电源 2 正极
【详细规格】 电源
冗余宽电压(9~48)VDC电源输入,典型工作电压12V/24V/48V 满载功耗小于3W 内置过流保护
13. LFP2 功能指示灯
http//:/
深圳市讯记科技有限公司 CK2000 系列 V1.0
10/100BaseT(X)以太网接口位于设备的前面板,接口类型为 RJ45。可以采用非屏蔽双绞线(UTP)或屏蔽双绞线(STP),连接距离
不超过 100m。100Mbps 连接采用 100Ω 的 5 类线,而 10Mbps 连接采用的是 100Ω 的 3、4、5 类线。
RJ45 端口支持自动 MDI/MDI-X 操作,可以使用直通线连接 PC 或服务器,连接其它交换机或集线器。在直通线(MDI)中,管
思科SF100D-05 08 16 SG100D-08非管理型桌面以太网交换机使用说明书
![思科SF100D-05 08 16 SG100D-08非管理型桌面以太网交换机使用说明书](https://img.taocdn.com/s3/m/c944d6c0ed3a87c24028915f804d2b160b4e86de.png)
使用说明书思科精睿 (Cisco Small Business)思科以太网交换机目录•思科 SF 100D-05、SF 100D-08、SF 100D-16 或 SG 100D-08 以太网交换机•壁挂套件•电源适配器欢迎感谢您选择思科 SF100D-05、SF100D-08、SF100D-16 或 SG100D-08 非管理型桌面以太网交换机,它是一种思科精睿 (Cisco Small Business) 网络通信设备。
绿色节能技术思科 SG100D-08 交换机支持绿色节能技术。
它可以进入睡眠模式、关闭不使用的端口和根据需要调整电源。
这样可以提高能源效率,帮助企业实现更低能耗并节省资金。
流量优先级流量优先级能够提供服务质量 (QoS) 功能;所有接收的数据包都将进行 QoS 优先级编码检查。
交换机将读取优先级级别并基于该优先级级别转发数据包。
例如,高负载期间,语音和视频流量将获得比数据流量更高的优先级。
(交换机的配置遵守 802.1p 标签框架。
)这可以确保时间性强的流量能够获得最高级别的服务。
要使用非管理型桌面以太网交换机上的 QoS 功能设置语音或视频流量的优先级,请在配置连接设备时将流量控制设置为off(关闭)。
否则流量控制可能会向交换机发送暂停帧,从而阻塞端口上已进入队列的高优先级 QoS 数据包。
在某些设备(如某些 IP 电话和 IP 照相机)上,流量控制可能无法配置。
巨型帧支持思科 SG100D-08 交换机支持高达 9,000 字节的帧(称为巨型帧)。
在传输大型文件(例如多媒体文件)期间,巨型帧支持允许在每个数据包中存在更大的载荷,从而可以提高网络吞吐量并降低 CPU 占用率。
非管理型桌面以太网交换机11安装思科非管理型桌面以太网交换机非管理型桌面以太网交换机可以放置平面上或安装到墙壁上。
请勿在存在以下情况的环境中部署设备:环境温度过高—环境温度不得超过 104 华氏度(40 摄氏度)。
华硕(ASUS)LNX-0602系列6口无管理工业以太网交换机用户手册说明书
![华硕(ASUS)LNX-0602系列6口无管理工业以太网交换机用户手册说明书](https://img.taocdn.com/s3/m/3a85dc0a001ca300a6c30c22590102020640f24b.png)
LNX-0602 series6-port Industrial Unmanaged Ethernet Switches4*10/100Tx + 2*100FxUser ManualFCC WarningThis Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:⏹Reorient or relocate the receiving antenna.⏹Increase the separation between the equipment and receiver.⏹Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.⏹Consult the dealer or an experienced radio/TV technician for help.CE Mark WarningThis is a Class-A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.ContentIntroduction (1)Features (1)Package Contents (2)Hardware Description (3)Physical Dimension (3)Front Panel (4)Top View (4)LED Indicators (5)Ports (6)Cabling (8)Wiring the Power Inputs (9)Wiring the Fault Alarm Contact (10)DIP Switch Settings (10)Mounting Installation (11)DIN-Rail Mounting (11)Wall Mounting (13)Hardware Installation (14)Installation Steps (14)Network Application (15)Troubleshooting (16)Technical Specification (17)IntroductionAntaira’s LNX-0602 series switches are smart 6-port Industrial Unmanaged Ethernet Switches supporting 4-Port 10/100Tx Fast Ethernet and 2-Port 100Fx of SC or ST type connector and support Multi-mode in 2Km, or Single-mode in 30Km.The LNX-0602 series switches support 12~48VDC power inputs. This series switches offer Extend Operating Temperature model (w/-T) supports -40°C ~ 75°C. It supports IEEE 802.3/802.3u/802.3x with 10/100BTx, full or half duplex, MDI/MDI-X auto sensing to provide an economical solution for the Industrial Ethernet Network.In addition, the Network Broadcast Storm Protection and built-in relay warning function alerts network engineers when power failures or port breaks occur.Features⏹System Interface/PerformanceRJ-45 ports support Auto MDI/MDI-X FunctionEmbedded 4-port 10/100Tx and 2-port 100Fx SC/ST type connector (Multi / Single mode)Store-and-Forward Switching ArchitectureBroadcast Storm Protection2K MAC Address TablePort Break Alarm Mask⏹Power InputDC 12 ~ 48V Redundant Power⏹Operating TemperatureStandard Operating Temperature model: -10°C ~ 70°CExtend Operating Temperature model with –T: -40°C ~ 75°C⏹Case/InstallationIP-30 ProtectionInstallation in Pollution Degree 2 EnvironmentDIN Rail and Wall Mount Design⏹Provides EFT protection 2,000 VDC for power line⏹Supports 6,000 VDC Ethernet ESD protectionPackage ContentsPlease refer to the package contents list below.⏹LNX-0602 series - 6-Port Industrial Unmanaged Switch with Fiber w/DIN RailBracket⏹User Manual⏹Removable Terminal Block⏹Wall-mount Kit (2 Wall-mount Plates with Screws)Compare the contents of the industrial switch with the checklist above. If any item is damaged or missing, please contact Antaira or Antaira’s authorized channel partners for service.Hardware DescriptionThe Industrial switch’s hardware spec, port, cabling information, and wiring installation will be described.Physical DimensionThe LNX-0602 series - 6-Port Industrial Unmanaged Ethernet Switch with Fiber dimension: (W x D x H) is 30mm x 99mm x 142mmFront PanelThe Front Panel of the Industrial Switch is shown below:Front Panel of the Industrial SwitchTop ViewThe top view of the Industrial Switch has one terminal block connector of two DC power inputs and relay circuit contact.Top View of the Industrial SwitchLED IndicatorsThe diagnostic LEDs located on the front panel of the industrial switch provide real-time information of the system and optional status. The following table provides the description of the LED status.Green OnFlashingOffGreen OnFlashingOffPorts⏹RJ-45 portsThe (RJ-45) Fast Ethernet ports will auto-sense for 10Base-T or 100Base-TX connections. Auto MDI/MDIX means that the switch can connect to another switch or workstation without changing straight through or crossover cabling. Please refer to the table below for RJ-45 pin assignment.⏹RJ-45 Pin AssignmentsNote “+” and “-” signs represent the polarity of the wires that make up each wire pair.All ports on this industrial switch supports automatic MDI/MDI-X operation, users can use straight-through cables (See figure below) for all network connections to PCs or servers, or to other switches or hubs. With straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of the cable. The table below shows the 10BASE-T/100BASE-TX MDI and MDI-X port pin outs.The following figures show the cable schematic for both straight-through type and crossover type.Straight Through Cable SchematicCross Over Cable SchematicFiber PortThe fiber port of SC type connector can work in multi mode or single mode. When you connect the fiber port to another one, please follow the figure below to connect accordingly. Wrong connection will cause the port cannot work normally.ATTENTIONThis is a Class 1 Laser/LED prod uct. Don’t stare into the Laser/LED Beam.Cabling⏹Twisted-pair segments can be connected with an unshielded twisted pair (UTP) orshielded twisted pair (STP) cable. The cable must comply with the IEEE 802.3u 100Base TX standard (e.g. Category 5, 5e, or 6). The cable between the equipment and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long.⏹ Fiber segment using single-mode connector type must use 9/125μm single-mode fibercable.⏹ Fiber segment using multi-mode connector type must use 50 or 62.5/125 μm multi-mode fiber cable.Wiring the Power InputsPlease follow the steps below to insert the power wire.Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+,V2-) contacts on the terminal block connector.Tighten the wire-clamp screws to prevent the wires from loosening.Note ∙Use Copper Conductors Only, 60/75°C, Tighten to 5 lb in∙The wire gauge for the terminal block should range between 18~20AWG.ON: Enables the corresponding PORT alarm. If the port ’s link fails, therelay will form an open circuit and the fault LED will turn on. Off: Disables the corresponding PORT alarm. The relaywill form a closed circuit and the fault LED will never turn on.B.S.P. On: Enables broadcast storm protection B.S.P. Off: Disables broadcast storm protectionWiring the Fault Alarm ContactThe fault alarm contact is in the middle of the terminal block connector as the picture shows below. By Inserting the wires, it will detect the fault status including power failure or port link failure (managed industrial switch only) and form a normally open circuit. An application example for the fault alarm contact is shown as below:Note∙ Use Copper Conductors Only, 60/75°C , Tighten to 5 lb in∙ The wire gauge for the terminal block should range between 12 ~ 24 AWG .DIP Switch SettingsThe following describes the DIP switch settings.Mounting InstallationDIN-Rail MountingThe DIN-Rail is screwed on the industrial switch from the factory. If the DIN-Rail is not screwed on the industrial switch, please see the following pictures to screw the DIN-Rail on the switch. Follow the steps below to hang the industrial switch.1. Use the screws to screw the DIN-Rail bracket on the rear side of the industrialswitch.2. To remove the DIN-Rail bracket, reverse the step 1.3. After the DIN-Rail bracket is screwed on the rear side of the switch, insert the top ofDIN-Rail on to the track.4. Then, lightly pull down the bracket on to the rail.5. Check if the bracket is mounted tight on the rail.6. To remove the industrial switch from the rail, reverse steps above.Wall MountingFollow the steps below to mount the industrial switch using the wall mount bracket.1. Remove the DIN-Rail bracket from the industrial switch; loosen the screws to removethe DIN-Rail.2. Place the wall mount bracket on the top and bottom of the industrial switch.3. Use the screws to screw the wall mount bracket on the industrial switch.4. Use the hook holes at the corners of the wall mount bracket to hang the industrialswitch on the wall.5. To remove the wall mount bracket, reverse steps above.Below is the dimension of the wall mount bracket.Hardware InstallationThis section is to explain how to install the LNX-0602 series –6-Port Industrial Unmanaged Ethernet Switch with Fiber.Installation Steps1. Unpack the Industrial switch packing.2. Check if the DIN-Rail bracket is screwed on the Industrial switch. If the DIN-Rail isnot screwed on the Industrial switch, please refer to the DIN-Rail Mounting section for DIN-Rail installation. If users want to wall mount the Industrial switch, then please refer to the Wall Mounting section for wall mount installation.3. To hang the Industrial switch on a DIN-Rail or wall, please refer to the MountingInstallation section.4. Power on the Industrial switch. Please refer to the Wiring the Power Inputs sectionfor information about how to wire power. The power LED on the Industrial switch will turn on. Please refer to the LED Indicators section for indication of LED lights.5. Prepare the twisted-pair, straight through Category 5/above cable for Ethernetconnection.6. Insert one side of the RJ-45 cable into the Industrial switch Ethernet port and on theother side to the network device’s Ethernet port, e.g. Switch, PC or Server. The Ethernet port (RJ-45) LED on the Industrial switch will turn on when the cable is connected to the network device. Please refer to the LED Indicators section for LED light indication.7. When all connections are set and the LED lights all show normal, the installation iscomplete.Network ApplicationThis segment provides an example of an industrial switch application.Troubleshooting⏹Verify the right power cord/adapter, never use power supply/adapter with non-compliant DC output voltage, or it will burn the equipment.⏹Select the proper UTP/STP cable to construct the network with using the right cable.Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100ΩCategory 5e/above cable for 10M/100Mbps. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).⏹Diagnosing LED Indicators: To assist in identifying problems, the Switch can beeasily monitored through LED indicators, which describe common problems a user may encounter and where the user can find possible solutions.⏹If the power indicator LED does not turn on when the power cord is plugged in, theuser may have a problem with the power cord. Check for loose power connections, power losses or surges at the power outlet. Please contact Antaira or Antaira’s authorized channel partners for technical support service, if the problem still cannot be resolved.⏹If the Industrial switch LED indicators are normal and the connected cables arecorrect but the packets still cannot transmit. Please check the system’s Ethernet devices’ configuration or status.Technical SpecificationThe LNX-0602 series - 6-Port Industrial Unmanaged Ethernet Switch with Fiber technical specifications is shown below.18。
Juniper Networks EX4300 以太网交换机系列 产品说明说明书
![Juniper Networks EX4300 以太网交换机系列 产品说明说明书](https://img.taocdn.com/s3/m/2065290ece84b9d528ea81c758f5f61fb7362892.png)
Data Sheet可扩展外形中类似机箱的功能EX4300 固定配置交换机含有大量通常与基于机箱的解决方案相关联的高可用性功能,包括:•可热插拔风扇•模块化的 Juniper Networks Junos®操作系统(与机箱系统一致)•虚拟机箱配置中具有平滑路由引擎切换 (GRES) 功能的双路由引擎 (RE)•单一管理界面•简单、集中式软件升级•从 24 个 10/100/1000BASE-T 端口扩展到 480 个以及从 24个 100/1000/2500/5000/10000BASE-T 端口扩展到 240 个的可扩展性,以及最多 40 个 10GbE 上行链路和 40 个40GbE 上行链路(多 Gb 型号上有最多 40 个 10GbE 上行链路、20 个 40GbE 上行链路,或 20 个 100GbE 上行链路,以及每台交换机 4 个专用 40 Gbps 虚拟机箱端口)每台 EX4300 交换机都包括一个基于 ASIC 的数据包转发引擎 EX-PFE。
集成的路由引擎 (RE) 提供所有控制平面功能。
EX4300 还使用与其他瞻博网络交换机、路由器和安全设备相同的模块化 Junos OS,从而确保跨瞻博网络基础架构一致地实施和操作控制平面功能。
架构和关键组件EX4300 交换机是单机架单元 (1 U) 设备,为空间和电力都十分宝贵的拥挤配线间和接入交换地点提供紧凑型解决方案。
每台EX4300 均支持标准 40GbE QSFP+ 端口,这些端口经过预配置,支持高速虚拟机箱底板连接;在 1GbE 接入交换机上,这些端口也可用作上游聚合设备的上行链路。
此外,每台 EX4300 还支持可选前面板上行链路模块,为配线间和上游聚合交换机之间的高速主干连接或链路聚合连接提供 1GbE 或 10GbE 端口;此多 Gb 型号提供 4 端口 10GbE SFP+ 上行链路模块或 2 端口 40GbE QSFP+/2 端口 100GbE QSFP28 上行链路模块两种选择。
RS205 千兆系列 工业级以太网交换机使用说明书
![RS205 千兆系列 工业级以太网交换机使用说明书](https://img.taocdn.com/s3/m/8870419da48da0116c175f0e7cd184254b351bf6.png)
RS205千兆系列工业级以太网交换机使用说明书事先未征得深圳市源拓光电技术有限公司(以下简称源拓光电)的书面同意,任何人不得以任何方式拷贝或复制本文档中的任何内容。
源拓光电不做与本文档相关的任何保证,不做商业性、质量或特定用途适用性的任何隐含保证。
本文档中的信息随时可能变更,而不另行通知。
源拓光电保留对本出版物做修订而不通知任何个人或团体此类变更的权利。
深圳市源拓光电技术有限公司地址:深圳市宝安区石岩街道石龙仔社区森海诺科创大厦12楼网址:电话:+86-755-26641737传真:+86-755-26640197第1章产品介绍包装清单打开包装之后,请检查以下设备和附件,如有缺失,请与我们联系。
1.1.产品概述RS205千兆系列是针对风电,配网,交通,石油石化等工业领域需求而开发的导轨型工业以太网交换机。
产品具有高速的包转发能力以及充裕的背板带宽,保证图像清晰,流畅的传输。
抗强振动的卡轨座,-40℃~+85℃极端环境温度适应能力及良好的EMC电磁兼容性能,使该系列产品具备在恶劣工业环境下稳定可靠工作的能力。
详细的机型配置表如下:机型配置表1.2.产品特点主要端口:提供千兆光口和千兆电口,电口支持10/100/1000Mbps自适应;电源特性:DC9-60V AC110-240V支持双电源输入,防反接保护功能;传输距离:电口0-100米;光口20km符合标准:IEEE802.3,IEEE802.3u,IEEE802.3z标准;安防抗扰:出色的防雷、防静电和抗电磁干扰能力,支持1路继电器告警输出;外观结构:IP40等级防护,高强度铝壳,DIN卡轨式安装,无风扇,低功耗设计;1.3.典型应用1.4.设备面板图正面板背面板和侧面板1:冗余电源输入端子和一组继电器端子2:DIN卡轨安装位置1.5.规格参数1.6.LED指示灯LED指示状态说明PWR 亮电源PWR连接运行正常灭电源PWR未连接或运行不正常L/A亮端口已建立有效的网络连接闪烁端口处于网络运行状态灭端口未建立有效的网络连接SPD10M/100/1000M 亮1000M工作模式(1000Base-T)灭10/100M工作模式ALM(仅双电源支持)亮交换机有告警事件灭交换机无告警事件第2章安装2.1.注意事项●在放置交换机时请注意稳定性,跌落将造成严重后果。
以太网交换机入门说明书
![以太网交换机入门说明书](https://img.taocdn.com/s3/m/06405630b94ae45c3b3567ec102de2bd9605dee6.png)
Figure 1: Fire or Combustion Triangle When it comes to engineering, the design must meet the criteria of the classified location. Basically, there are three techniques to avoid a fire or explosion: containment (explosion proof enclosures and fittings), segregation (purge and pressurization of enclosures),Table 4: Class/Division System Compared to Zone System.*The -ER suffix indicates additional crush and impact test requirements and can be used as ‘exposed’ or ‘open’ wiring. When coming out of the cable tray, and the connection is less than six feet away to an end device such as a motor, cables with an ER rating can be used if they are properly supported and given adequate mechanical protection. Mechanical protection consists of struts, angle, or channels.In addition to the approved cable types there are other acceptable wires/cables that can be used with the proper pathway. Any suitable type of wire or cable can be used if installed in threaded metallic conduit with approved termination fittings. Defining ‘suitable’ type of wire is the responsibility of the AHJ but typically wire or cable approved for unclassified (non-hazardous) will be accepted. Many common off the shelf industrial devices, such as network switches, PLC’s, 24V DC power supplies, and Panduit 24V UPS are rated for Class I Division 2 locations. These devices are designed and manufactured to minimize the risk by addressing factors like spacing, fuses, relays, connectors, and surface temperatures. Manufactures may have a separate model that conforms to CID2 but in many cases there may be only one version. It is common for these devices to not be mounted in the hazardous area, but they have the certification regardless.Class I Division 2Reference ➢ Threaded rigid metal conduit or threaded steel intermediate metal conduit➢ Type PLTC and PLTC-ER (Power Limited Tray Cable – Exposed Run)*Article 725 ➢ Type ITC and ITC-ER (Instrumented Tray Cable – Exposed Run)*Article 727 ➢ Type MC (Metal Clad)Article 330 ➢ Type MV (Medium Voltage)Article 328 ➢ Type TC and TC-ER (Tray Cable – Exposed Run)*Article 336 ➢ Optical Fiber cable types allowed: OFNP , OFCP , OFNR, OFCR, OFNG, OFCG, OFN & OFC Installed in raceways that meet Article 501 requirementsArticle 770Table 6: CID2 Wiring MethodsClass I Division 2 (NEC Article 501)This classification is the most common hazardous environment. Methods that are approved for CID1 are allowed for CID2 locations as CID1 construction is more stringent than C1D2 construction. Division 2 includes additional cable types that can be used since there is less exposure to the hazard. Cable types such as Power Limited Tray Cable (PLTC) must be mounted in cable tray with listed fittings to meet the requirements. Cables with a proper sheath, Metal Clad for example, can be mounted without a pathway as long as the cable run is properly supported. Table 6 summarizes these methods and provides the NEC article reference where more information can be found on a specific cable type. For each type of cable listed there are installation requirements that are described as part of Article 501.NonincendiveNonincendive is not a common term but it is another type of classification for hazardous areas. There are a several types of ‘Nonincendive’ (circuit/component/equipment/field wiring) as defined in the NEC Article 100. Nonincendive is defined as having electrical/electronic equipment that is incapable, under normal operating conditions, of causing ignition of the surrounding atmosphere due to arcing or thermal means. Normal operating conditions are defined as maximum voltage under open circuit conditions and maximum current under short circuit conditions. Nonincendive devices are approved for use in a Division 2environment (also can be used for Class III Division 1) and therefore do not require protection such as an explosion proof enclosure or an intrinsically safe barrier. An advantage of this approach is cost when compared to Intrinsically Safe and explosion proof options. Nonincendive field wiring shall be permitted using any of the wiring methods permitted for unclassified locations and installed according to the control drawing.An example of a nonincendive device for CID2 is the Panduit VeriSafe ™ Absence of Voltage Tester (AVT), see figure 2. This rating allows the device to be mounted in control panels that are in the classified area. Any type of non-hazardous wiring can be used provided the manufacturer’s installation instructions are followed.Standards Apply to VS-AVT2 OnlyISA 12.12.01Nonincendive Electrical Equipment rated for Class I, Division 2 area classification, Groups A, B, C, D, and temperature classification T3.Class III (NEC Article 503)Class III focuses on textile mills where easily ignitable fibers/flyings are present in the manufacturing process. Examples of other Class III areas include cotton gins and seed mills, flax producing or handling facilities, pulverizing or shaping plants, and clothing manufacturing facilities. Sawmills and other woodworking plants where combustible fibers/flyings are present may also become hazardous locations. Fibers/flyings are hazardous because they are easily ignited but also because flames quickly spread through them. Class III locations do not have material group designations. Table 8 summarizes these acceptable methods for Class III division 1 and 2.Intrinsically Safe (NEC Article 504)Intrinsically safe equipment is defined as equipment and wiring which is incapable of releasing sufficient electrical or thermal energy under normal or abnormal conditions to create a hazardous situation. Intrinsically safe systems commonly use a standalone barrier that contains energy limiting electronics. Conceptually, the function of an intrinsically safe barrier is like that of a fuse or circuit breaker. When too much energy is detected from the barrier the barrier will react and ‘open’ the circuit. Any of the wiring methods for unclassified (non-hazardous) locations can be used as long as the conditions specified in the control drawings are followed. The intrinsically safe application is viewed as a circuit and each device that is part of the system must follow the design. Control drawings are typically supplied with the intrinsically safe barrier and will specify the requirements of the cabling. It is also important that the intrinsically safe wire is isolated and clearly marked so that it is not accidentally mixed with other wiring. Typically, intrinsically safe wire is blue in color and labeled so it can be easily recognized. For more information on intrinsic safety refer to UL 698A and/or NEC article 504.Class III Division 1 and Division 2➢ Rigid metal conduit, PVC conduit, RTRC conduit, intermediate metal conduit, electrical metallic tubing, dust tight wireways➢ Type MC or MI cable with listed termination fittings ➢ Type PLTC and PLTC-ER cable ➢ Type ITC and ITC-ER➢ Type MC, MI, MV, TC/TC-ER cable (requires ventilation and specific spacing)Table 8: Class III Wiring MethodsSummaryThe NEC has an abundance of information and guidance for hazardous locations found in Chapter 5 (Article 500 to 506). Traditionally the NEC has followed the Class/Division segmentation but with the addition of Article 505 and 506 there is now a reference to the Zone schema that is used internationally. When installing outside of the United States be sure to follow the standards and regulations for that area, ATEX and IECEx are common outside of the US. Direct cross referencing of standards is usually not allowed unless the device is provided with a dual rating. Be aware that there are differences between Classes and Divisions that are not incremental and do not transfer from one to the other. For example, a Class I device cannot be used in a Class III area unless it has been rated for that area.Appropriate materials selection and installation practices are documented in the NEC and are used to create a safe design that can be approved by the authority having jurisdiction. Following these 3 steps will provide a proper install; determine the correct hazardous area classification, review the wiring types allowed for proper cable selection, and installing the cable per the requirements of the hazardous location. Each classified area has a list of approved wiring methods as shown in the tables within this paper. Additional details for the applicable standards of these wiring methods should be researched prior to developing a design. Interpretations of the requirements are subjective, so it is crucial to include any local codes and communicate with the proper authority for the specific location. In most cases there are several options available and having the proper information will result in a successful project.Panduit ProductsIt is challenging to generally classify products due to the many details and the variety of standards that apply to different situations. The FAQ section and chart below provides guidance for common situations and a starting point for product specification. Today there are many products that offer Class I Division 2 ratings; this provides more flexibility when installing in a hazardous location.What type of enclosure is needed for Class I Division 2? Can a Panduit Zone enclosure be used?In CID2 locations, enclosures, fittings, and joints are not required to be explosionproof if they contain no arcing devices and the equipment used in the panel is CID2 rated. Control panels containing solid-state relays, solenoids, and control transformers (as long as the devices operating temperature doesn’t exceed 80% of ignition temperature) are considered non-arcing devices per article 501.105(B)(3 and 4). Therefore, a NEMA 4 rated Zone Enclosure with CID2 rated equipment, such as a Stratix® switch or PLC, can be mounted in the CID2 classified area without the need for an explosion proof rating. This guidance is assuming that the area of installation does NOT require explosion proof seal. Division 2 wiring methods indicated in Article 501.10(B) must be adhered to for the installation.Additionally, some motor control devices that are mounted in control panels can have CID2 ratings. For example, devices suchas circuit breakers/motor controllers/switches that are sealed and not arc producing can be listed as CID2 rated devices. Article 501.115 and 501.120 provide more details on the exceptions but reviewing any equipment’s labeling and/or manuals will statethe rating to which it has been tested and certified.What rating is required for cables and connectors used in a Class I Division 2 control panel?Cables and connectors used in a CID2 control panel, not requiring explosion proof seal, do not have to have a hazardous location listing. As long as the equipment is ‘listed’ it can be used. To clarify, there are two types of terminology used in the NEC code;‘listed’ and ‘listed for the location’. Listed for the locations typically refers to an item being rating for the explosion proof area. However, the term ‘listed’ refers to a more general recognition such as general purpose or ordinary. The term ‘listed’ refers to a component that is tested to a standard by a Nationally Recognized Testing Laboratory such as UL or CSA. Therefore, for these CID2 control panels, Panduit network products such as patch cables, RJ45 plugs/jacks, and related equipment that are used inside the control panel are allowed. Any type of wiring that is outside of the enclosure must adhere to the Division 2 wiring methods indicated in Section 501.What type of fittings are needed for Class I Division 2 installations for Zone Enclosures (or other control panels)? Generally speaking, if the installation requires an explosionproof seal, the fitting must be an explosionproof fitting, rated, listed, and marked for either Class I, Division 1 or Class I, Division 2. If the installation does not require an explosionproof seal, all that is required is an ordinary or general-purpose rated and listed fitting compatible with the appropriate Division 2 wiring method being used. When equipment being installed does not rely on an explosionproof method of protection and does not have ignition concerns then explosionproof enclosures and fittings are not needed per section 501.10(B)(4) of the NEC.What cable can be used inside threaded metal conduit that meets Class I applications?Standard Panduit enterprise or industrial copper cable and fiber can be used in threaded rigid metal conduit. The media used in this pathway only needs to be listed (general recognition) and is not required to have any type of explosion proof rating. The threaded metal conduit provides the protection requiredMore Meaningful Connections11 WHITE PAPER – Specifying Cable Infrastructure in Hazardous Locations Per NEC StandardsThis chart contains Panduit products that can be installed in different types of hazardous locations.Part Number DescriptionApplications Type of use in hazardous locationClass IDiv 1Class I Div 2Class II Div 1Class II Div 2Class III Div 1&2IURHT5C04BL-UG Category 5e 4-pair UTP 600 V 22 AWG solid Type PLTC*Ethernet Networks EtherNet/IPRMC Cable Tray RMC Cable Tray Cable Tray ESFLHT5C02FGR-X Category 5e 2-pair SF/UTP 600 V 22 AWG stranded Type AWM, ITC, PLTC*Ethernet Networks PROFINET Type B/C RMC Cable Tray RMC Cable Tray Cable Tray ESFLHT5C02GR-X Category 5e 2-pair SF/UTP 22 AWG solid Type PLTC*Ethernet Networks PROFINET Type A RMC Cable Tray RMC Cable Tray Cable Tray UPS00100DC Maintenance-free, No battery, 100 Watts, 24VDCPower back up for 24VDC devices Not Rated Yes Not Rated Yes Yes Z22U-S14 and -S15Universal Network Zone EnclosureHousing network switches and devices Not RatedYes**Not Rated Yes**Yes**Z23U-S24 and -S25FODPZ12Y OFNP plenum, 50µm OM4, 900µm buffered fibersIndoor Distribution fiberCable Tray FODPZ24Y FSDP912Y OFNP plenum, 50µm OS2, 900µm buffered fibersIndoor Distribution fiberCable Tray FSDP924Y FOPPZ12Y OFCP plenum, 50µm OM4, 900µm buffered fibersIndoor Distribution interlocking armor Cable Tray FOPPZ24Y FSPP912Y OFCP plenum, 9µm OS2, 900µm buffered fibersIndoor Distribution interlocking armor Cable Tray FSPP924Y FOCPZ12Y OFNP plenum, 50µm OM4, 250µm fibers Indoor/outdoor loose tube cableCable Tray FONPZ24Y FSCP912Y OFNP plenum, 9µm OS2, 250µm fibers Indoor/outdoor loose tube cable Cable Tray FSNP924Y FSJD912OFNR-LS riser LSZH, OS2Industrial Dielectric Double Jacketed Cable Tray FOJDZ12OFNR-LS riser LSZH, OM4Industrial Dielectric Double JacketedCable Tray* Power Limited Tray Cable (PLTC) applications reduce rating to 300 V ** When equipped with location approved equipmentAWM = Appliance Wiring Material ITC = Instrument Tray cable PLTC = Power Limited Tray CableRMC = Rigid Metal Conduit (thick walled threaded metal tubing)OFCP = Fiber Optic Conductive Plenum OFNP = Fiber Optic Nonconductive PlenumOFNR-LS = Fiber Optic Nonconductive Riser LSZH = Low smoke Zero HalogenCable tray = Unit or assembly of units and the associated fittings that form a structural system used to securely fasten or support cables and raceways. Example of cable tray is Panduit Wyr-Grid® Overhead Tray Routing System. In addition to cable tray other installations types are available, refer to NEC Article 725.Acronym decoder list:THE INFORMATION CONTAINED IN THIS WHITE PAPER IS INTENDED AS A GUIDE FOR USE BY PERSONS HAVING TECHNICAL SKILL AT THEIR OWN DISCRETION AND RISK. BEFORE USING ANY PANDUIT PRODUCT, THE BUYER MUST DETERMINE THE SUITABILITY OF THE PRODUCT FOR HIS/HER INTENDED USE AND BUYER ASSUMES ALL RISK AND LIABILITY WHATSOEVER IN CONNECTION THEREWITH. PANDUIT DISCLAIMS ANY LIABILITY ARISING FROM ANY INFORMATION CONTAINED HEREIN OR FOR ABSENCE OF THE SAME.All Panduit products are subject to the terms, conditions, and limitations of its then current Limited Product Warranty, which can be found at /warranty.* All trademarks, service marks, trade names, product names, and logos appearing in this document are the property of their respective owners.©2020 Panduit Corp. ALL RIGHTS RESERVED. CPAT82--WW-ENG 8/2020Since 1955, Panduit’s culture of curiosity and passion for problem solving have enabled more meaningful connections between companies’ business goals and their marketplace success. Panduit creates leading-edge physical, electrical, and network infrastructure solutions for enterprise-wide environments, from the data center to the telecom room, from the desktop to the plant floor. Headquartered in Tinley Park, IL, USA and operating in 112 global locations, Panduit’s proven reputation for quality and technology leadership, coupled with a robust partner ecosystem, help support, sustain, and empower business growth in a connected world.PANDUIT US/CANADA Phone: 800.777.3300PANDUIT EUROPE LTD.London, UK*******************Phone: 44.20.8601.7200PANDUIT JAPAN Tokyo, Japan********************Phone: 81.3.6863.6000PANDUIT SINGAPORE PTE. LTD.Republic of Singapore *****************Phone: 65.6305.7575PANDUIT AUSTRALIA PTY. LTD.Victoria, Australia ******************Phone: 61.3.9794.9020PANDUIT LATIN AMERICA Guadalajara, Mexico *****************Phone: 52.33.3777.6000ContactPanduitNorthAmericaCustomerServicebyemail:**************or by phone: 800.777.3300Visit us at For more information。
GS110MX千兆以太网交换机用户手册说明书
![GS110MX千兆以太网交换机用户手册说明书](https://img.taocdn.com/s3/m/ced1a3710622192e453610661ed9ad51f11d544d.png)
将设备连接到交换机1. 将设备连接到交换机前面板上的 RJ-45 网络端口。
端口 1 至 8 支持 1G 、100M 和 10M 。
端口 9 和 10 支持 10G 、5G 、 2.5G 、1G 和 100M 。
请使用本安装指南另一面推荐的电缆。
2. 将交换机上的一个 RJ-45 端口连接到网络。
在高速网络中,使用端口 9 或 10。
注意:在小型办公室或家庭办公室网络,将交换机连接到已连接至互联网调制解调器的路由器的 LAN 端口。
8 端口非网管千兆以太网交换机 (配 2 个万兆/多千兆上行端口)将电源适配器连接到直流输入检查 LED状态包装内容• 交换机• 电源适配器(因销售国家而异)• 机架安装托架和螺钉• 用于墙式安装的墙壁安装螺钉,用于桌面安装的胶垫(一个包装袋中)• 墙式安装螺钉电源 LED 指示灯端口 1 至 8 的千兆以太网端口 LED通电断电1G 链路(两个端口 LED 点亮)。
两个端口 LED 闪烁表示流量活动。
100M 链路(左侧端口 LED 点亮,右侧端口 LED 熄灭)。
左侧端口 LED 闪烁表示流量活动。
10M 链路(左侧端口 LED 熄灭,右侧端口 LED 点亮)。
右侧端口 LED 闪烁表示流量活动。
无链路(两个端口 LED 熄灭)。
端口 9 和 10 的多千兆以太网端口 LED10G 链路(两个端口 LED 点亮)。
两个端口 LED 闪烁表示流量活动。
5G 链路(左侧端口 LED 点亮,右侧端口 LED 熄灭)。
左侧端口 LED 闪烁表示流量活动。
2.5G 链路(左侧端口 LED 熄灭,右侧端口 LED 点亮)。
右侧端口 LED 闪烁表示流量活动。
1G 或 100M 链路(两个端口 LED 点亮)。
两个端口 LED 闪烁表示流量活动。
无链路(两个端口 LED 熄灭)。
连接示例至 10G NAS的 10G 链路至 WAC740 AP的 1G 链路至计算机的 1G 链路至 WAC740 AP 的 2.5G 链路至计算机的 1G 链路至计算机的 1G 链路2017 年 9 月© NETGEAR, Inc. NETGEAR 和 NETGEAR 徽标是 NETGEAR (美国网件公司)的商标。
PSW618A交换机说明书
![PSW618A交换机说明书](https://img.taocdn.com/s3/m/23bde77a168884868762d6ad.png)
国 电 南 自 Q/GDNZ.JB.221-2008PSW 618A工业以太网交换机说明书国电动份南京自化股有限公司 GUODIAN NANJING AUTOMATION CO.,LTDPSW 618A工业以太网交换机说明书编写审核批准(此页仅供审查签署用,不印刷)V :1.0国电南京自动化股份有限公司2008年12月安全声明警告:处理不当易导致交换机损坏或人身伤害,非专业人士勿碰。
注意:请按照交换机背面电源指示正确接线。
本交换机内部没有需要用户调节的开关、跳线、变阻器等部件,用户不需要拆开机箱。
危险:交换机内部、交换机电源接口端子可以带有非安全电压,切勿徒手触摸。
版本声明本说明书适用于PSW 618A工业以太网交换机V1.0版本产品说明书版本修改记录表10987654321序号说明书版本号修改摘要软件版本号修改日期* 技术支持电话:(025)8353 7286传真:(025)8353 7201*本说明书可能会被修改,请注意核对实际产品与说明书的版本是否相符* 200X年X月第X版第X次印刷l国电南自技术部监制目录安全声明版本声明1 概述 (6)1.1 适用范围 (6)1.2 性能特点 (6)2 技术性能及指标 (7)2.1 额定电气参数 (7)2.2 主要技术指标 (7)2.3 大气条件 (7)2.4 绝缘性能 (8)2.5 耐湿热性能 (8)2.6 电磁兼容性能 (8)2.7 机械性能 (9)3 功能及原理 (9)4 系统连接 (9)4.1 通信与规约 (10)5 硬件构成 (10)5.1 结构、外观及安装尺寸 (10)5.2 面板布置说明 (10)5.3 对外接口及电源接点 (11)6 操作说明 (12)6.1 面板说明 (12)6.2 配置功能操作 (12)6.3 其它问题说明 (15)7 维护需知 (15)8 订货须知及其他 (15)1 概述1.1 适用范围PSW618A工业以太网交换机采用适合电力行业使用的“前面板显示,后面板连线”的结构,外形为19英寸1U标准机箱。
SUP-2118M以太网交换机使用手册
![SUP-2118M以太网交换机使用手册](https://img.taocdn.com/s3/m/0e58fbf84693daef5ef73df8.png)
以太网交换机SUP-2118M1基本说明以太网交换机SUP-2118M,具有端口交换,网络速度自适应。
与传统的集线器相比,其全双工运行模式提高了网络带宽。
SUP-2118M型交换机是SUP-2116G的增强型,主要体现在增加了(1~2)个100Mbps SC光接口、直通线和交叉线自适应等功能,可用于工业网络、宽带小区、电信、金融证券、企业、政府、校园网等。
由于存在两个光接口,因此,最大可以接入两路多模或单模的光路,同时,两个光口可以互为冗余和互补,保证上行线路的畅通。
2功能特点¾符合IEEE802.3 10BASE-T和IEEE802.3u 100BASE-TX/FX标准¾单片集成18个口的主芯片¾10/100M 自适应 RJ-45端口¾100M SC多/单模端口¾MDI-X自适应功能¾存储和转发交换方式¾IEEE 802.3x流量控制用于全双工¾背压技术支持半双工流量控制¾广播风暴控制¾标准机架设计3性能指标¾网络标准:IEEE802.3 10BASE-T和IEEE802.3u 100BASE-TX/FX¾包转发率:10BASE-T为14880pps,100BASE-TX/FX为148800pps¾协议:CSMA/CD¾交换方式:存储转发¾端口数:16个RJ-45端口,可附加(1~2)个SC端口(可选件)¾缓存大小:1.5Mbit¾MAC地址:4k MAC地址¾功耗: <15.3W¾重量: 2.5kg¾输入电压:(100~220)V AC±10%(50/60Hz)¾电口z类型:CAT5类双绞线z传送距离:(0~100)mz传输速率:10/100Mbps¾光口z类型:多模 62.5/125µm光纤单模 9/125µm光纤z传送距离:多模双纤(0~2)km单模双纤(0~20)kmz输出功率:多模双纤(–20 ~ 0)dBm单模双纤(–14 ~–8)dBmz输入功率:多模双纤-30dBm单模双纤-35dBmz中心波长:1310nmz传输速率:100Mbpsz发送信号:TXz接收信号:RX4使用说明SUP-2118M型交换机外观图如下图所示。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
以太网交换机使用说明书目录物品清单 (4)第一章用户手册简介 (5)1.1 用途 (5)1.2 约定 (5)1.3 用户手册概述 (5)第二章产品概述 (6)2.1 产品简介 (6)2.2 产品特性 (6)2.2.1 主要特性 (6)2.2.2 规格说明 (7)第三章安装指南 (8)3.1 安装 (8)3.1.1 安装在桌面上的方法 (8)3.1.2 安装在机架上的方法 (8)3.1.3 加电 (8)3.2 交换机的外观 (8)3.2.1 前面板 (8)3.2.2 后面板 (10)3.3 注意事项 (10)第四章交换机基本概念 (12)4.1 系统配置 (12)4.1.1 系统信息 (12)4.1.2 IP地址参数 (12)4.1.3 文件传输 (12)4.1.4 保存与复位 (13)4.2 端口管理 (13)4.2.1 端口参数 (13)4.2.2 端口监控 (14)4.2.3 端口描述 (14)4.2.4 端口统计与端口状态 (14)4.2.5 端口带宽 (15)4.2.6 端口广播风暴 (15)4.3 网络配置 (15)4.3.1 最大老化时间与动态地址表 (15)4.3.2 静态地址表 (16)4.3.3 静态安全地址表 (16)4.3.4 Ping检测 (16)4.4 虚拟局域网管理 (16)4.4.1 VLAN模式配置 (17)4.4.2 Global VID配置 (18)4.4.3 VLAN配置 (18)VLAN组 (19)4.4.4 MTU4.5 Trunk配置 (19)4.6 优先级管理 (20)4.6.1 优先级配置 (20)4.6.2 端口优先级表 (20)4.6.3 TOS优先级 (20)4.6.4 802.1p优先级 (20)4.6.5 802.1p优先级映射表 (21)第五章 WEB管理 (22)5.1 概述 (22)5.2 WEB管理的连接 (22)5.2.1 准备工作 (22)5.2.2 连接 (25)5.3 WEB管理界面及操作方法 (26)5.3.1 系统配置 (27)5.3.2 端口管理 (30)5.3.3 网络配置 (37)5.3.4 VLAN管理 (41)5.3.5 Trunk配置 (45)5.3.6 优先级管理 (46)第六章带外管理 (52)6.1 概述 (52)6.2 带外(out-of-out)的连接方法 (52)6.3 带外管理的界面及操作方法 (53)6.4 CLI命令使用说明 (53)6.4.1 语法帮助 (53)6.4.2 命令帮助使用说明 (53)6.4.3 常用命令 (54)管理 (58)第七章 Telnet7.1 概述 (58)7.2 Telnet的连接方法 (58)7.3 连接 (60)附录A RJ-45插座/连接器引脚详细说明 (62)物品清单小心打开包装盒,检查包装盒里应有的配件:一台交换机一根交流电源线一根串口线一本用户手册两个L型支架(KN-S1008M+除外)如果发现包装盒内产品有所损坏或者任何配件短缺的情况,请及时和当地经销商联系。
第一章用户手册简介感谢您购买KN-S1008M+/KN-S1016MF/KN-S1024M+百兆管理型交换机和KN-S1026MGF千兆管理型交换机。
本系列交换机提供多方面的管理功能,整体性能优越,使用简单,是您提升工作组性能的理想选择。
1.1 用途本手册的用途是帮助您熟悉和快捷的使用KN-S1008M+/KN-S1016MF/KN-S1024M+百兆管理型交换机和KN-S1026MGF千兆管理型交换机。
1.2 约定在本手册以下部分,均以KN-S1026MGF交换机为例,并且所提到的交换机系指KN-S1026MGF千兆管理型交换机。
1.3 用户手册概述第一章:用户手册简介。
第二章:产品概述。
描述交换机的构造和基本特性。
第三章:安装指南。
指导您进行交换机的基本安装步骤。
第四章:交换机基本概念。
第五章: WEB管理。
讲述如何使用WEB连接进行交换机管理。
第六章:带外管理。
讲述如何使用带外管理连接进行交换机管理。
第七章: Telnet管理。
讲述如何使用Telnet管理连接进行交换机管理。
附录A: RJ-45插座/连接器引脚详细说明。
第二章产品概述2.1 产品简介KN-S1008M+/KN-S1016MF/KN-S1024M+百兆管理型交换机和KN-S1026MGF千兆管理型交换机完全符合IEEE802.3 Ethernet标准,智能配置管理设置可为建立小型、中型、大型网络提供理想的组网解决方案。
KN-S1008M+/KN-S1016MF/KN-S1024M+百兆管理型交换机和KN-S1026MGF千兆管理型交换机提供多方面的管理功能,可对系统、端口、网络、VLAN、Trunk、优先级、安全等进行管理。
您可以通过WEB浏览器对KN-S1008M+/KN-S1016MF/KN-S1024M+百兆管理型交换机和KN-S1026MGF千兆管理型交换机进行管理。
并且可以通过RS232串口查看系统配置信息、修改IP网络参数、修改登录密码等。
KN-S1016MF/KN-S1026MGF百兆/千兆管理型交换机有独立的SFP插槽,支持100M/1000M系列光纤模块;千兆的电口,为网络提供千兆上联(KN-S1026MGF)。
丰富的接入方式扩充了端口数量、扩展网络连接半径,使网络的接入更加灵活。
2.2 产品特性2.2.1 主要特性符合IEEE 802.3、IEEE 802.3u、IEEE 802.3ab、IEEE 802.3z标准全双工采用IEEE 802.3x标准,半双工采用Backpressure标准8/16/24/24个10/100M自适应RJ-45端口2个1000M自适应RJ-45端口(KN-S1026MGF)支持端口自动翻转(Auto MDI/MDIX)提供1个100M SFP 光纤扩展槽与16号端口共享(KN-S1016MF)提供2个1000M SFP光纤扩展槽与两个千兆端口共享(KN-S1026MGF)KN-S1016MF/KN-S1026MGF支持光电共享端口的光电自动切换提供一个终端(DTE)设备配置串口支持8/16/24/26个Port VLAN ,256个IEEE 802.1 Q Tag VLAN支持MTU VLAN组支持静态MAC地址表(KN-S1008M+)提供端口安全控制功能,支持静态安全地址表的管理,每个端口最多可设置16组MAC 地址(KN-S1008M+)支持MAC地址绑定功能(KN-S1016MF/24M+/26MGF)支持端口汇聚(Port Trunk)功能;支持端口镜像(Port Mirror)支持端口优先级、TOS优先级、IEEE 802.1 p优先级协议模式支持IEEE 802.1 p优先级映射支持广播风暴控制,可减少广播风暴和分割广播风暴支持基于端口的带宽限制全中文Web管理界面,支持本地升级(支持TFTP远程升级)支持通过TFTP的配置文件导入和导出支持静态IP地址设置和动态从DHCP服务器获取交换机IP地址支持超级终端、Telnet等多种管理动态LED指示灯,提供简单的工作状态提示及故障排除内置优质电源,稳定可靠1U全钢外壳,优良散热支持标准19英寸机架安装(KN-S1008M+除外)2.2.2 规格说明产品型号KN-S1008M+ KN-S1016MF KN-S1024M+ KN-S1026MGF支持的标准和协议 IEEE802.3、IEEE 802.3u、IEEE 802.3x、IEEE 802.3ab1000M 无 2 端口数100M 8 16 24 24 SFP扩展槽无1(100M)无2(1000M)网络介质10Base-T:3类或3类以上UTP;100Base-TX:5类UTP;1000Base-T:超5类或6类以上UTPMAC地址表8K 8K 8K 8K 背板带宽 1.6G 3.2G 4.8G 8.8G 过滤和转发速率 10Mbps:14880pps; 100Mbps:148800pps;100Mbps:148800pps 10/100M Link/Act(连接/工作)LED指示其它 Power(电源)外形尺寸(L×W×H)单位(mm)230×147×44 440×205×44 440×205×44 440×205×44使用环境工作温度:0℃~40℃;工作湿度10%~90%不凝结存储温度: -40℃~70℃;存储湿度5%~90%不凝结输入电源输入:180-260V AC,50-60Hz;第三章安装指南3.1 安装首先,请按照下述步骤妥当地安置好交换机:必须放在至少能承重5kg的表面上。
供电的电源插座距离交换机须在1.5米之内。
确保电源线已可靠地连接在交换机后面板上的电源接口和供电的电源插座间。
保证交换机有良好的通风散热环境,并且请勿将重物放置在交换机上。
3.1.1 安装在桌面上的方法1. 将交换机底部朝上放在足够大且稳定的桌面上。
2. 逐个揭去4个脚垫的胶面保护纸,分别粘贴在机壳底部4个角上圆形凹槽中。
3. 再将交换机翻转过来,平稳的放在桌面上。
3.1.2 安装在机架上的方法交换机尺寸是符合EIA(Electronic Industries Association)电子工业协会的标准19英寸支架。
1. 将配件中的两个L型支架分别安装在交换机面板的两侧(配件提供螺钉)2. 再将交换机安放在机架内3. 然后将交换机固定好(螺钉用户自备)图3-1 安装L型支架示意图3.1.3 加电交换机的供电输入电压范围是180-260伏(50-60Hz)的交流电,交换机的内置电源系统可以根据实际输入的电压自动调整其工作电压。
当交换机正常加电后,交换机前面板上的电源(Power)指示灯亮。
注意:当供电系统出现掉电故障或临时停电时,为了确保交换机不被突发性的大电流损坏,请务必将交换机的电源线从供电的插座上拔下来。
当供电恢复正常后,再将交换机的电源线插上。
3.2 交换机的外观对交换机的前面板、后面板进行详细说明。
3.2.1 前面板KN-S1026MGF交换机前面板由2个SFP扩展槽,2个1000M端口,24个10/100Mbps 端口,一个Console端口(RS232串口)和相关的LED灯组成,如下图所示:图3-2 KN-S1026MGF交换机的前面板示意图串口串口(Console端口或者是RS232口)位于前面板的最右侧,它是带外管理时和计算机连接的接口,通过提供的串口线,可对系统信息、网络参数、安全管理等进行配置。
说明:KN-S1008M+的串口在后面板的最左侧。