nport串口服务器调试说明
Nport串口服务器说明书
文件级别：文件编号：MOXA Nport 5630 设备使用说明书1．０版编制：汤浩校核：喻鹏、谭华审定：批准：长沙华能自控集团有限公司一、简介MOXA Nport 5600系列产品是一种和后台电脑用网络连接的串口服务器。
NPort 5600 系列多个不同的后台电脑可以共同分享１个Nport 5600设备二、Nport 5600通信线制作Nport 5600 系列串口接线引脚引脚号RS232 RS422 / 4线RS485 2线RS4851 DSR2 RTS3 GND TXD+4 TXD TXD-5 RXD RXD- DATA-6 DCD RXD+ DATA+7 CTS GND GND8 DTR三、Nport 5600设置面板和按钮说明灯：LED 灯-灯颜色-含义LED灯颜色含义准备灯红正在启动中，长期则是有错误绿正常1-8/16通信信号灯正在接收数据绿正在发送数据按键:键名称- 含义MENU菜单键∧上翻键∨下翻键SEL选择键先在NPORT 5600上把NPORT 5600的IP设置好，具体操作方法如Menu(主选单) → NetWork Setting → IP Address →设置为192.168.X.X→ NetMask →设置为255.255.255.0四、后台电脑设置在后台电脑中安装好Nport 5600的驱动程，安装完毕后在开始菜单中选择程序，然后再选择刚安装好的NPort Administration Suite NPort Administrator打开后选择Broadcast Search （自动查找在网络内的Nport ）配置Nport 5600设置PORTx 端口的通信方式Com Mapping (串口映射)也就是把NPORT 的PORTx 映射为电脑中的COM到此设置完毕，点击中的Apply应用刚才的设置。
后台软件中的串口的COM MAPPING中的COM PORT应相对应。
Nport5630串口服务器说明书
文件级别：文件编号:MOXA Npｏrt5630设备使用说明书1.0版编制：汤浩校核：喻鹏、谭华审定:批准：长沙华能自控集团有限公司一、简介MOＸＡNport5600系列产品就是一种与后台电脑用网络连接得串口服务器。
NＰｏrt ５60０系列ﻫ多个不同得后台电脑可以共同分享１个Npoｒｔ56０0设备二、Npoｒt５6００通信线制作Npｏrt ５600 系列串口接线引脚引脚号RS2３2 RS4２2/ 4线RＳ485 2线ＲＳ４８51 DＳR2 RTS３GNＤＴXD+４ＴXD ＴXD-5 RXD RXＤ－ＤAＴＡ—6 DＣD RXD+ ＤATＡ+7 CTS ＧND GＮD８DTR三、Nport 5600设置面板与按钮说明灯：LEＤ灯－灯颜色-含义LＥD灯颜色含义准备灯红正在启动中，长期则就是有错误绿正常１—8/1６通信信号灯正在接收数据绿正在发送数据按键：键名称—含义ＭENU菜单键∧上翻键∨下翻键SEL选择键先在NPＯRＴ5600上把NPORＴ5６０0得IＰ设置好，具体操作方法如Ｍｅnｕ(主选单）→NｅtWork Ｓetｔｉng → IP Ａddｒｅss →设置为192、1６8、X、X→ＮetＭasｋ→设置为２５5、255、25５、0四、后台电脑设置在后台电脑中安装好Ｎport5600得驱动程,安装完毕后在开始菜单中选择程序,然后再选择刚安装好得NPort Adminｉsｔｒａtion Sｕite→ NPｏrｔAdminisｔrator打开后选择BroadcastＳｅａrｃｈ（自动查找在网络内得Npｏrｔ）配置Ｎpｏrt 5600设置PＯＲＴx 端口得通信方式Ｍａｐpiｎg （串口映射)也就就是把NPORＴ得ＰOＲＴx映射为电脑中得到此设置完毕，点击中得Apply应用刚才得设置。
后台软件中得串口得ＭAPPＩNG中得PORＴ应相对应.后台软件中得其它设置请参阅MTＣ得帮助文件。
Moxa NPort 5100A 串口到网络设备服务器说明书
NPort5100A Series1-port RS-232/422/485serial device serversFeatures and Benefits•Power consumption of only1W•Fast3-step web-based configuration•Surge protection for serial,Ethernet,and power•COM port grouping and UDP multicast applications•Screw-type power connectors for secure installation•Real COM/TTY drivers for Windows and Linux•Standard TCP/IP interface and versatile TCP and UDP operation modes•Connects up to8TCP hostsCertificationsIntroductionThe NPort®5100A device servers are designed to make serial devices network-ready in an instant and give your PC software direct access to serial devices from anywhere on the network.The NPort®5100A device servers are ultra-lean,ruggedized,and user-friendly,making simple and reliable serial-to-Ethernet solutions possible.A Greener Serial-to-Ethernet SolutionThe MiiNe is a small but powerful Arm-based serial-to-Ethernet SoC with RAM and Flash embedded.With the MiiNe inside,the NPort®5110A Series'power consumption is less than1W.The NPort®5100A Series saves at least50%on power consumption compared to existing solutions on the market,helping engineers meet the tough environmental compliance challenges found in today’s industrial environments.Surge Protection for Serial,Ethernet,and PowerSurge,which is typically caused by high voltages that result from switching and lightning transients,is a common threat to all electrical devices. Moxa’s leading-edge surge immunity solution,which is applied to the NPort®5100A’s serial,power,and Ethernet lines,is tested and proven compliant with IEC61000-4-5.This state-of-the-art surge protection provides a robust serial-to-Ethernet solution that can protect electrical devices from voltage spikes and withstand electrically noisy environmental conditions.3-Step Web-based ConfigurationThe NPort®5100A’s3-step web-based configuration tool is straightforward and user-friendly.The NPort®5100A’s web console guides users through three simple configuration steps that are necessary to activate the serial-to-Ethernet application.With this fast3-step web-based configuration,a user only needs to spend an average of30seconds to complete the NPort®settings and enable the application,saving a great amount of time and effort.Easy to TroubleshootNPort®5100A device servers support SNMP,which can be used to monitor all units over Ethernet.Each unit can be configured to send trap messages automatically to the SNMP manager when user-defined errors are encountered.For users who do not use SNMP manager,an email alert can be sent ers can define the trigger for the alerts using Moxa’s Windows utility,or the web console.For example,alerts can be triggered by a warm start,a cold start,or a password change.AppearanceSpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)1Magnetic Isolation Protection 1.5kV(built-in)Ethernet Software FeaturesConfiguration Options Windows Utility,Serial Console,Telnet Console,Web Console(HTTP/HTTPS) Management DHCP Client,ARP,BOOTP,DNS,HTTP,HTTPS,ICMP,IPv4,LLDP,SMTP,SNMPv1/v2c,TCP/IP,Telnet,UDPFilter IGMP v1/v2Windows Real COM Drivers Windows95/98/ME/NT/2000,Windows XP/2003/Vista/2008/7/8/8.1/10(x86/x64),Windows2008R2/2012/2012R2(x64),Windows Embedded CE5.0/6.0,Windows XPEmbeddedLinux Real TTY Drivers Kernel versions:2.4.x,2.6.x,3.x,4.x,and5.xFixed TTY Drivers SCO UNIX,SCO OpenServer,UnixWare7,QNX4.25,QNX6,Solaris10,FreeBSD,AIX5.x,HP-UX11i,Mac OS XAndroid API Android3.1.x and laterMIB RFC1213,RFC1317Serial InterfaceConnector DB9maleNo.of Ports1Serial Standards NPort5110A:RS-232NPort5130A:RS-422,RS-485NPort5150A:RS-232,RS-422,RS-485Operation Modes Disabled,Ethernet Modem,Pair Connection,Real COM,Reverse Telnet,RFC2217,TCPClient,TCP Server,UDPBaudrate Supports standard baudrates(unit=bps):50,75,110,134,150,300,600,1200,1800,2400,4800,7200,9600,19200,38400,57600,115200,230.4k,460.8k,921.6kData Bits5,6,7,8Stop Bits1,1.5,2Parity None,Even,Odd,Space,MarkFlow Control RTS/CTS(RS-232only),DTR/DSR(RS-232only),XON/XOFFPull High/Low Resistor for RS-4851kilo-ohm,150kilo-ohmsRS-485Data Direction Control ADDC®(automatic data direction control)Terminator for RS-485120ohmsSerial SignalsRS-232TxD,RxD,RTS,CTS,DTR,DSR,DCD,GNDRS-422Tx+,Tx-,Rx+,Rx-,GNDRS-485-4w Tx+,Tx-,Rx+,Rx-,GNDRS-485-2w Data+,Data-,GNDPower ParametersNo.of Power Inputs1Input Current NPort5110A:82.5mA@12VDCNPort5130A:89.1mA@12VDCNPort5150A:92.4mA@12VDCInput Voltage12to48VDCSource of Input Power Power input jackReliabilityAutomatic Reboot Trigger Built-in WDTPhysical CharacteristicsHousing MetalDimensions(with ears)75.2x80x22mm(2.96x3.15x0.87in)Dimensions(without ears)52x80x22mm(2.05x3.15x0.87in)Weight340g(0.75lb)Installation Desktop,DIN-rail mounting(with optional kit),Wall mountingEnvironmental LimitsOperating Temperature Standard Models:0to60°C(32to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to75°C(-40to167°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:0.5kVIEC61000-4-6CS:150kHz to80MHz:10V/m;Signal:10V/mIEC61000-4-8PFMFIEC61000-4-11DIPsSafety UL60950-1DeclarationGreen Product RoHS,CRoHS,WEEEMTBFTime2,231,530hrsStandards Telcordia(Bellcore)Standard TR/SRWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x NPort5100A Series device serverPower Supply1x power adapter,suitable for your region(standard temp.models only) Documentation1x quick installation guide1x warranty cardDimensionsNPort5110A NPort5150ANPort5130AOrdering InformationModel NameOperating Temp.Baudrate Serial Standards No.of Serial Ports Input Current Input Voltage NPort 5110A 0to 60°C 50bps to 921.6kbpsRS-232182.5mA @12VDC 12-48VDC NPort 5110A-T -40to 75°C 50bps to 921.6kbpsRS-232182.5mA @12VDC 12-48VDC NPort 5130A 0to 60°C 50bps to 921.6kbps RS-422/485189.1mA @12VDC 12-48VDCNPort5130A-T-40to75°C 50bps to921.6kbpsRS-422/485189.1mA@12VDC12-48VDCNPort5150A0to60°C 50bps to921.6kbpsRS-232/422/485192.4mA@12VDC12-48VDCNPort5150A-T-40to75°C 50bps to921.6kbpsRS-232/422/485192.4mA@12VDC12-48VDCAccessories(sold separately)CablesCBL-F9M9-150DB9female to DB9male serial cable,1.5mCBL-F9M9-20DB9female to DB9male serial cable,20cmConnectorsADP-RJ458P-DB9F DB9female to RJ45connectorMini DB9F-to-TB DB9female to terminal block connectorDIN-Rail Mounting KitsDK35A DIN-rail mounting kit,35mmPower AdaptersPWR-12050-WPAU-S1Locking barrel plug,12VDC,0.5A,100to240VAC,Australia(AU)plug,0to40°C operatingtemperaturePWR-12050-WPCN-S1Locking barrel plug,12VDC,0.5A,100to240VAC,China(CN)plug,0to40°C operating temperature PWR-12050-WPEU-S1Locking barrel plug,12VDC,0.5A,100to240VAC,Continental Europe(EU)plug,0to40°C operatingtemperaturePWR-12050-WPUK-S1Locking barrel plug,12VDC,0.5A,100to240VAC,United Kingdom(UK)plug,0to40°C operatingtemperaturePWR-12050-WPUSJP-S1Locking barrel plug,12VDC,0.5A,100to240VAC,United States/Japan(US/JP)plug,0to40°Coperating temperaturePWR-12150-AU-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,Australia(AU)plug,-40to75°C operatingtemperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-CN-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,China(CN)plug,-40to75°C operatingtemperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-EU-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,Continental Europe(EU)plug,-40to75°Coperating temperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-UK-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,United Kingdom(UK)plug,-40to75°C operatingtemperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-USJP-SA-T Locking barrel plug,12VDC1.5A,100to240VAC,United States/Japan(US/JP)plug,-40to75°Coperating temperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPower CordsCBL-PJ21NOPEN-BK-30Locking barrel plug to bare-wire cable©Moxa Inc.All rights reserved.Updated Mar04,2020.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
Nport5630串口服务器使用说明
MOXA Nport 5630通信设备使用说明书文件级别：文件编号：MOXA Nport 5630 设备使用说明书1．０版编制：汤浩校核：喻鹏、谭华审定：批准：MOXA Nport 5630通信设备使用说明书长沙华能自控集团有限公司一、简介MOXA Nport 5600系列产品是一种和后台电脑用网络连接的串口服务器。
NPort 5600 系列多个不同的后台电脑可以共同分享１个Nport 5600设备MOXA Nport 5630通信设备使用说明书二、Nport 5600通信线制作Nport 5600 系列串口接线引脚引脚号RS232 RS422 / 4线RS485 2线RS4851 DSR2 RTS3 GND TXD+4 TXD TXD-5 RXD RXD- DATA-6 DCD RXD+ DATA+7 CTS GND GND8 DTRMOXA Nport 5630通信设备使用说明书三、Nport 5600设置面板和按钮说明灯：LED 灯-灯颜色-含义LED灯颜色含义准备灯红正在启动中，长期则是有错误MOXA Nport 5630通信设备使用说明书按键:先在NPORT 5600上把NPORT 5600的IP设置好，具体操作方法如Menu(主选单) → NetWork Setting → IP Address →设置为192.168.X.X→ NetMask →设置为255.255.255.0四、后台电脑设置在后台电脑中安装好Nport 5600的驱动程，安装完毕后在开始菜单中选择程序，然后再选择刚安装好的NPort Administration Suite→ NPort Administrator打开后选择Broadcast Search （自动查找在网络内的Nport ）MOXA Nport 5630通信设备使用说明书配置Nport 5600设置PORTx 端口的通信方式MOXA Nport 5630通信设备使用说明书Com Mapping (串口映射)也就是把NPORT 的PORTx 映射为电脑中的COMMOXA Nport 5630通信设备使用说明书。
Moxa NPort 5100A 1-Port 串口设备服务器说明书
NPort5100A Series1-port RS-232/422/485serial device servers with serial surge protectionFeatures and Benefits•Power consumption of only1W•Fast3-step web-based configuration•Surge protection for serial,Ethernet,and power•COM port grouping and UDP multicast applications•Screw-type power connectors for secure installation•Real COM and TTY drivers for Windows,Linux,and macOS•Standard TCP/IP interface and versatile TCP and UDP operation modes•Connects up to8TCP hostsCertificationsIntroductionThe NPort®5100A device servers are designed to make serial devices network-ready in an instant and give your PC software direct access to serial devices from anywhere on the network.The NPort®5100A device servers are ultra-lean,ruggedized,and user-friendly,making simple and reliable serial-to-Ethernet solutions possible.A Greener Serial-to-Ethernet SolutionThe MiiNe is a small but powerful Arm-based serial-to-Ethernet SoC with RAM and Flash embedded.With the MiiNe inside,the NPort®5110A Series'power consumption is less than1W.The NPort®5100A Series saves at least50%on power consumption compared to existing solutions on the market,helping engineers meet the tough environmental compliance challenges found in today’s industrial environments.Surge Protection for Serial,Ethernet,and PowerSurge,which is typically caused by high voltages that result from switching and lightning transients,is a common threat to all electrical devices. Moxa’s leading-edge surge immunity solution,which is applied to the NPort®5100A’s serial,power,and Ethernet lines,is tested and proven compliant with IEC61000-4-5.This state-of-the-art surge protection provides a robust serial-to-Ethernet solution that can protect electrical devices from voltage spikes and withstand electrically noisy environmental conditions.3-Step Web-based ConfigurationThe NPort®5100A’s3-step web-based configuration tool is straightforward and user-friendly.The NPort®5100A’s web console guides users through three simple configuration steps that are necessary to activate the serial-to-Ethernet application.With this fast3-step web-based configuration,a user only needs to spend an average of30seconds to complete the NPort®settings and enable the application,saving a great amount of time and effort.Easy to TroubleshootNPort®5100A device servers support SNMP,which can be used to monitor all units over Ethernet.Each unit can be configured to send trap messages automatically to the SNMP manager when user-defined errors are encountered.For users who do not use SNMP manager,an email alert can be sent ers can define the trigger for the alerts using Moxa’s Windows utility,or the web console.For example,alerts can be triggered by a warm start,a cold start,or a password change.AppearanceSpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)1Magnetic Isolation Protection 1.5kV(built-in)Ethernet Software FeaturesConfiguration Options Windows Utility,Web Console(HTTP/HTTPS),Device Search Utility(DSU),MCC Tool,Telnet Console,Serial Console(NPort5110A/5150A models only)Management DHCP Client,ARP,BOOTP,DNS,HTTP,HTTPS,ICMP,IPv4,LLDP,SNTP,SMTP,SNMPv1/v2c,TCP/IP,Telnet,UDPFilter IGMP v1/v2Windows Real COM Drivers Windows95/98/ME/NT/2000,Windows XP/2003/Vista/2008/7/8/8.1/10/11(x86/x64),Windows2008R2/2012/2012R2/2016/2019(x64),Windows Server2022,WindowsEmbedded CE5.0/6.0,Windows XP EmbeddedLinux Real TTY Drivers Kernel versions:2.4.x,2.6.x,3.x,4.x,and5.xFixed TTY Drivers macOS10.12,macOS10.13,macOS10.14,macOS10.15,SCO UNIX,SCO OpenServer,UnixWare7,QNX4.25,QNX6,Solaris10,FreeBSD,AIX5.x,HP-UX11i,Mac OS X Android API Android3.1.x and laterMIB RFC1213,RFC1317Security FunctionsAuthentication Local databaseEncryption HTTPS,AES-128,SHA-1,RSA-1024,SHA-256Security Protocols HTTPS(TLS1.2)Serial InterfaceConnector DB9maleNo.of Ports1Serial Standards NPort5110A:RS-232NPort5130A:RS-422,RS-485NPort5150A:RS-232,RS-422,RS-485Operation Modes Disabled,Ethernet Modem,Pair Connection,Real COM,Reverse Telnet,RFC2217,TCPClient,TCP Server,UDPBaudrate Supports standard baudrates(unit=bps):50,75,110,134,150,300,600,1200,1800,2400,4800,7200,9600,19200,38400,57600,115200,230.4k,460.8k,921.6kData Bits5,6,7,8Stop Bits1,1.5,2Parity None,Even,Odd,Space,MarkFlow Control RTS/CTS(RS-232only),DTR/DSR(RS-232only),XON/XOFFPull High/Low Resistor for RS-4851kilo-ohm,150kilo-ohmsRS-485Data Direction Control NPort5150A/5150A-T/5130A/5130A-T:ADDC(automatic data direction control) Terminator for RS-485120ohmsSerial SignalsRS-232TxD,RxD,RTS,CTS,DTR,DSR,DCD,GNDRS-422Tx+,Tx-,Rx+,Rx-,GNDRS-485-4w Tx+,Tx-,Rx+,Rx-,GNDRS-485-2w Data+,Data-,GNDPower ParametersNo.of Power Inputs1Input Current NPort5110A:82.5mA@12VDCNPort5130A:89.1mA@12VDCNPort5150A:92.4mA@12VDCInput Voltage12to48VDCSource of Input Power Power input jackReliabilityAutomatic Reboot Trigger Built-in WDTPhysical CharacteristicsHousing MetalDimensions(with ears)75.2x80x22mm(2.96x3.15x0.87in)Dimensions(without ears)52x80x22mm(2.05x3.15x0.87in)Weight340g(0.75lb)Installation Desktop,DIN-rail mounting(with optional kit),Wall mountingEnvironmental LimitsOperating Temperature Standard Models:0to60°C(32to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to75°C(-40to167°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/35EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:0.5kVIEC61000-4-6CS:150kHz to80MHz:10V/m;Signal:10V/mIEC61000-4-8PFMFIEC61000-4-11Safety UL60950-1DeclarationGreen Product RoHS,CRoHS,WEEEMTBFTime2,231,530hrsStandards Telcordia(Bellcore)Standard TR/SRWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x NPort5100A Series device serverPower Supply1x power adapter,suitable for your region(standard temp.models only) Documentation1x quick installation guide1x warranty cardDimensionsNPort5110A NPort5150ANPort5130AOrdering InformationModel NameOperating Temp.Baudrate Serial Standards No.of Serial Ports Input Current Input Voltage NPort 5110A 0to 60°C 50bps to 921.6kbpsRS-232182.5mA @12VDC 12-48VDC NPort 5110A-T -40to 75°C 50bps to 921.6kbpsRS-232182.5mA @12VDC 12-48VDC NPort 5130A 0to 60°C 50bps to 921.6kbps RS-422/485189.1mA @12VDC 12-48VDCNPort5130A-T-40to75°C 50bps to921.6kbpsRS-422/485189.1mA@12VDC12-48VDCNPort5150A0to60°C 50bps to921.6kbpsRS-232/422/485192.4mA@12VDC12-48VDCNPort5150A-T-40to75°C 50bps to921.6kbpsRS-232/422/485192.4mA@12VDC12-48VDCAccessories(sold separately)CablesCBL-F9M9-20DB9female to DB9male serial cable,20cmCBL-F9M9-150DB9female to DB9male serial cable,1.5mConnectorsADP-RJ458P-DB9F DB9female to RJ45connectorMini DB9F-to-TB DB9female to terminal block connectorDIN-Rail Mounting KitsDK35A DIN-rail mounting kit,35mmPower AdaptersPWR-12050-WPAU-S1Locking barrel plug,12VDC,0.5A,100to240VAC,Australia(AU)plug,0to40°C operatingtemperaturePWR-12050-WPCN-S1Locking barrel plug,12VDC,0.5A,100to240VAC,China(CN)plug,0to40°C operating temperature PWR-12050-WPEU-S1Locking barrel plug,12VDC,0.5A,100to240VAC,Continental Europe(EU)plug,0to40°C operatingtemperaturePWR-12050-WPUK-S1Locking barrel plug,12VDC,0.5A,100to240VAC,United Kingdom(UK)plug,0to40°C operatingtemperaturePWR-12050-WPUSJP-S1Locking barrel plug,12VDC,0.5A,100to240VAC,United States/Japan(US/JP)plug,0to40°Coperating temperaturePWR-12150-AU-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,Australia(AU)plug,-40to75°C operatingtemperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-CN-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,China(CN)plug,-40to75°C operatingtemperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-EU-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,Continental Europe(EU)plug,-40to75°Coperating temperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-UK-SA-T Locking barrel plug,12VDC,1.5A,100to240VAC,United Kingdom(UK)plug,-40to75°C operatingtemperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPWR-12150-USJP-SA-T Locking barrel plug,12VDC1.5A,100to240VAC,United States/Japan(US/JP)plug,-40to75°Coperating temperatureApplicable Models:NPort5110A-TNPort5130A-TNPort5150A-TPower CordsCBL-PJ21NOPEN-BK-30Locking barrel plug to bare-wire cable©Moxa Inc.All rights reserved.Updated Apr26,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
莫萨NPort P5150A系列1口RS-232 422 485PoE串口设备服务器说明书
NPort P5150A Series1-port RS-232/422/485PoE serial device serversFeatures and Benefits•IEEE802.3af-compliant PoE power device equipment•Speedy3-step web-based configuration•Surge protection for serial,Ethernet,and power•COM port grouping and UDP multicast applications•Screw-type power connectors for secure installation•Real COM/TTY drivers for Windows and Linux•Standard TCP/IP interface and versatile TCP and UDP operation modesCertificationsIntroductionNPort®P5150A device servers are designed to make serial devices network-ready in an instant.It is a power device and is IEEE802.3af compliant, so it can be powered by a PoE PSE device without an additional power e the NPort®P5150A device servers to give your PC software direct access to serial devices from anywhere on the network.The NPort®P5150A device servers are ultra-lean,ruggedized,and user-friendly, making simple and reliable serial-to-Ethernet solutions possible.Surge Protection for Serial,Ethernet,and PowerSurge,which is typically caused by high voltages that result from switching and lightning transients,is a common threat to all electrical devices. Moxa’s leading-edge surge immunity solution,which is applied to the NPort®P5150A’s serial,power,and Ethernet lines,is tested and proven compliant with IEC61000-4-5.This state-of-the-art surge protection provides a robust serial-to-Ethernet solution that can protect electrical devices from voltage spikes and withstand electrically noisy environmental conditions.3-Step Web-Based ConfigurationThe NPort®P5150A’s3-step web-based configuration tool is straightforward and user-friendly.The NPort®P5150A’s web console guides users through3simple configuration steps that are necessary to activate the serial-to-Ethernet application.With this speedy3-step web-based configuration,a user only needs to spend an average of30seconds to complete the NPort®settings and enable the application,saving a great amount of time and effort.Easy to TroubleshootNPort®P5150A device servers support SNMP,which can be used to monitor all units over Ethernet.Each unit can be configured to send trap messages automatically to the SNMP manager when user-defined errors are encountered.For users who do not use SNMP manager,an email alert can be sent ers can define the trigger for the alerts using Moxa’s Windows utility,or the web console.For example,alerts can be triggered by a warm start,a cold start,or a password change.AppearanceSpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)1Magnetic Isolation Protection 1.5kV(built-in)Standards PoE(IEEE802.3af)Ethernet Software FeaturesConfiguration Options Windows Utility,Serial Console,Telnet Console,Web Console(HTTP)Management DHCP Client,IPv4,SMTP,SNMPv1,Telnet,DNS,HTTP,ARP,BOOTP,UDP,TCP/IP,ICMPFilter IGMP v1/v2Windows Real COM Drivers Windows95/98/ME/NT/2000,Windows XP/2003/Vista/2008/7/8/8.1/10(x86/x64),Windows2008R2/2012/2012R2(x64),Windows Embedded CE5.0/6.0,Windows XPEmbeddedFixed TTY Drivers SCO UNIX,SCO OpenServer,UnixWare7,QNX4.25,QNX6,Solaris10,FreeBSD,AIX5.x,HP-UX11i,Mac OS XLinux Real TTY Drivers Kernel version:2.4.x,2.6.x,3.x,4.xAndroid API Android3.1.x and laterMIB RFC1213,RFC1317Serial InterfaceConnector DB9maleNo.of Ports1Serial Standards RS-232,RS-422,RS-485Operation Modes Disabled,Ethernet Modem,Pair Connection,Real COM,Reverse Telnet,RFC2217,TCPClient,TCP Server,UDPBaudrate Supports standard baudrates(unit=bps):50,75,110,134,150,300,600,1200,1800,2400,4800,7200,9600,19200,38400,57600,115200,230.4k,460.8k,921.6kData Bits5,6,7,8Stop Bits1,1.5,2Parity None,Even,Odd,Space,MarkFlow Control RTS/CTS,DTR/DSR,XON/XOFFPull High/Low Resistor for RS-4851kilo-ohm,150kilo-ohmsRS-485Data Direction Control ADDC®(automatic data direction control)Serial SignalsRS-232TxD,RxD,RTS,CTS,DTR,DSR,DCD,GNDRS-422Tx+,Tx-,Rx+,Rx-,GNDRS-485-4w Tx+,Tx-,Rx+,Rx-,GNDRS-485-2w Data+,Data-,GNDPower ParametersInput Current DC Jack I/P:125mA@12VDCPoE I/P:180mA@48VDCInput Voltage12to48VDC(supplied by power adapter),48VDC(supplied by PoE) No.of Power Inputs1Source of Input Power Power input jackPoEPhysical CharacteristicsHousing MetalDimensions(with ears)100x111x26mm(3.94x4.37x1.02in)Dimensions(without ears)77x111x26mm(3.03x4.37x1.02in)Weight300g(0.66lb)Environmental LimitsOperating Temperature NPort P5150A:0to60°C(32to140°F)NPort P5150A-T:-40to75°C(-40to167°F)Storage Temperature(package included)-40to75°C(-40to167°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:4kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:3V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:1kVIEC61000-4-6CS:150kHz to80MHz:3V/m;Signal:3V/mIEC61000-4-8PFMFIEC61000-4-11DIPsSafety UL60950-1MTBFTime2,231,530hrsStandards Telcordia(Bellcore)Standard TR/SRWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x NPort P5150A Series device serverDocumentation1x document and software CD1x quick installation guide1x warranty cardDimensionsOrdering InformationModel Name Operating Temp.Baudrate Serial Standards No.of Serial Ports Input VoltageNPort P5150A0to60°C50bps to921.6kbps RS-232/422/485112-48VDC by power adapter or48VDC by PoENPort P5150A-T-40to75°C50bps to921.6kbps RS-232/422/485112-48VDC by power adapter or48VDC by PoEAccessories(sold separately)CablesCBL-F9M9-150DB9female to DB9male serial cable,1.5m CBL-F9M9-20DB9female to DB9male serial cable,20cm ConnectorsADP-RJ458P-DB9F DB9female to RJ45connectorMini DB9F-to-TB DB9female to terminal block connectorDIN-Rail Mounting KitsDK35A DIN-rail mounting kit,35mmPower AdaptersPWR-12050-WPAU-S1Locking barrel plug,12VDC,0.5A,100-240VAC,Australia(AU)plug,0to40°C operating temperature PWR-12050-WPCN-S1Locking barrel plug,12VDC,0.5A,100-240VAC,China(CN)plug,0to40°C operating temperature PWR-12050-WPEU-S1Locking barrel plug,12VDC,0.5A,100-240VAC,Continental Europe(EU)plug,0to40°C operatingtemperaturePWR-12050-WPUK-S1Locking barrel plug,12VDC,0.5A,100-240VAC,United Kingdom(UK)plug,0to40°C operatingtemperaturePWR-12050-WPUSJP-S1Locking barrel plug,12VDC,0.5A,100-240VAC,United States/Japan(US/JP)plug,0to40°Coperating temperaturePWR-12150-AU-SA-T Locking barrel plug,12VDC,1.5A,100-240VAC,Australia(AU)plug,-40to75°C operatingtemperatureApplicable Models:NPort P5150A-TPWR-12150-CN-SA-T Locking barrel plug,12VDC,1.5A,100-240VAC,China(CN)plug,-40to75°C operating temperatureApplicable Models:NPort P5150A-TPWR-12150-EU-SA-T Locking barrel plug,12VDC,1.5A,100-240VAC,Continental Europe(EU)plug,-40to75°C operatingtemperatureApplicable Models:NPort P5150A-TPWR-12150-UK-SA-T Locking barrel plug,12VDC,1.5A,100-240VAC,United Kingdom(UK)plug,-40to75°C operatingtemperatureApplicable Models:NPort P5150A-TPWR-12150-USJP-SA-T Locking barrel plug,12VDC1.5A,100-240VAC,United States/Japan(US/JP)plug,-40to75°Coperating temperatureApplicable Models:NPort P5150A-TPower WiringCBL-PJ21NOPEN-BK-30Locking barrel plug to bare-wire cable©Moxa Inc.All rights reserved.Updated Apr10,2019.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
Moxa NPort 5000AI-M12 铁路串口设备服务器说明书
NPort5000AI-M12系列鐵路1、2和4埠RS-232/422/485串列裝置伺服器特色與優點•快速的3步驟網頁式配置•COM連接埠分組和UDP多播應用•用於Windows和Linux的Real COM/TTY驅動程式•標準TCP/IP介面及通用TCP和UDP操作模式•符合EN50121-4標準•符合所有EN50155規範強制性測試項目1•M12連接器和IP40金屬外殼•串列訊號的2kV隔離認證簡介NPort®5000AI-M12串列裝置伺服器能夠讓串列裝置立即聯網，並提供從網路上隨處直接存取串列裝置的能力。
此外，NPort5000AI-M12符合EN 50121-4和EN50155的所有強制性部分，涵蓋操作溫度、電源輸入電壓、突波、ESD和震動，適用於運作環境中有許多震動的軌道和軌旁應用。
3步驟網頁式配置NPort5000AI-M12的3步驟網頁式配置工具簡單明瞭且方便使用。
NPort5000AI-M12的網路主控台引導使用者透過三個簡單的配置步驟來啟動串列轉乙太網路應用。
透過這種快速的3步驟網頁式配置，使用者平均只需要30秒即可完成NPort設定和啟用應用程式，達到節省大量時間和精力的效果。
輕鬆排除故障NPort5000AI-M12裝置伺服器支援SNMP，可用於透過乙太網路監控所有裝置。
各個裝置都可以配置為在遇到使用者定義的錯誤時自動向SNMP管理器傳送陷阱訊息。
對於不使用SNMP管理器的使用者，可以改為傳送電子郵件警示。
使用者可以使用Moxa的Windows公用程式或Web主控台定義警示的觸發條件。
例如，警示可以由暖開機、冷開機或密碼變更觸發。
規格Ethernet Interface110/100BaseT(X)Ports(M12D-coded4-pin femaleconnector)Ethernet Software FeaturesConfiguration Options Telnet Console,Web Console(HTTP/HTTPS),Windows UtilityManagement ARP,BOOTP,DHCP Client,DNS,HTTP,HTTPS,ICMP,IPv4,LLDP,SMTP,SNMPv1/v2c,TCP/IP,Telnet,UDPFilter IGMP v1/v2Windows Real COM Drivers Windows95/98/ME/NT/2000,Windows XP/2003/Vista/2008/7/8/8.1/10(x86/x64),Windows2008R2/2012/2012R2(x64),Windows Embedded CE5.0/6.0,Windows XPEmbeddedLinux Real TTY Drivers Kernel versions:2.4.x,2.6.x,3.x,4.x,and5.x1.此產品適用於符合EN50155標準所定義的所有軌道車輛應用。
nport串口服务器调试说明
现场调试NPORT5232
1．将电脑连入NPORT5232的网络，点击search,将会收到网络上的所有NPORT5232，根据MAC地址确定将要调试的设备。
2．双击要调试的设备。
Network是用来设置设备的IP地址，要修改必须勾选Modify ,才能操作。
Serial是用来修改485口的波特率等参数。
Operating Mode 是用来调试485口的工作模式：
TCP模式，用于以太网网络传输报文。
一般第一个485口设定4001端口，第二个485设定为4002端口。
REAL模式，将485映射到电脑，虚拟成电脑的COM口。
我们一般都在REAL模式下发送报文，以调试485总线设备（如扶梯，西门子PLC等）点击“COM Mapping”
再点击“Add”，添加我们需要映射的Nport5232，注意，我们映射的端口必须被改为REAL 模式才行。
然后点击“Apply”，选择没有占用的端口，即可（相当于电脑有了COM3，COM4等端口）。
如果端口映射不了，请关闭防火墙或杀毒软件，重新安装Nport软件。
经过如上设置，我们就可以用串口调试工具发送和接收报文了。
串口调试工具Commix 用法：
双击：Commix
设定好后点击“Open Port”再在报文发送框内填写报文。
Port:设定电脑将要通讯的COM口。
（可以是Nport5232映射的端口）
输入16进制的报文，点击，Send
次窗口会显示485总线上的发送和接收的信。
NPORT5610串口服务器使用说明
NPORT5610串口服务器使用说明NPORT5610串口服务器是一种能够将串口设备连接到网络的设备。
它提供了一种简单和可靠的方法来远程访问和管理串口设备，并实现了串口设备的自动化控制和监控。
下面将详细介绍NPORT5610串口服务器的使用说明，包括设备的设置和配置、基本操作和常见问题解答。
1.设备的设置和配置：a.硬件安装：将NPORT5610串口服务器插入到电源插座，并使用一个以太网电缆将其与网络连接起来。
b. IP 地址设置：通过串口或以太网口（Telnet 或基于 Web 的界面）连接到 NPORT 5610，然后使用设备的默认 IP 地址登录到设备管理界面。
在界面中，您可以设置设备的 IP 地址、子网掩码和网关地址。
c.串口设置：在设备管理界面中，您可以配置每个串口的参数，如波特率、数据位、停止位和奇偶校验位。
还可以选择是启用流控制、启用XON/XOFF流控制还是启用DSR/CTS流控制。
d.访问控制设置：在设备管理界面中，您可以设置访问控制列表，限制哪些IP地址可以访问NPORT5610。
这有助于保护设备免受未经授权的访问。
2.基本操作：a.连接到串口设备：使用一个串口线连接NPORT5610的串口端口和目标串口设备。
确保串口线的接口与目标设备的接口类型匹配。
b.连接到网络：将NPORT5610插入到电源插座，并使用一个以太网电缆将其连接到网络中的一个可用端口。
c. 远程访问和管理：在电脑上打开一个终端软件（如 Tera Term、PuTTY等），通过指定 NPORT 5610 的 IP 地址和串口设置进行远程访问和管理。
3.常见问题解答：a.无法连接到设备：确保NPORT5610的电源和网络连接正常，并检查IP地址、子网掩码和网关地址的设置是否正确。
b.串口通讯故障：如果无法与目标串口设备进行通讯，请检查串口设备的设置是否正确，并确保串口线的接口匹配。
c.访问控制配置：如果希望限制特定IP地址访问设备，请确保设置了正确的访问控制列表，并且IP地址没有被阻止。
MOXA NPort5110系列串口转换器 配置说明书
NPort口5110系列串口转换器配置说明书一、硬件设备NPort5110，二、线缆连接NPort5110的串口和串口设备相连（DB9连接头2、3交叉）NPort5110的net口和网络相连（NPort5110和计算机直连用交叉线，和交换机连用直通线）三、硬件设置NPort5110端的网络设置如下：打开IE浏览器，在地址栏中输入http://192.168.127.254即可进入moxa模块的配置页面。
（注：192.168.127.254 为moxa NPort5110的默认IP地址，必须保证当前计算机的IP是192.168.127.*号段）NPort5110的IP地址，与图7中“Remote IP”一致备注：1）本公司出厂的NPort 5110的初始IP地址为：192.168.1.* (2<*<255)。
2）若按下NPort 5110端部的“Reset Button”将其复位后，此时，NPort 5110的初始IP地址为：192.168.127.254备注：1）本公司出厂的NPort 5110的初始密码为：newu ，用户可在步骤四中进行更改。
2）若按下NPort 5110端部的“Reset Button”将其复位后，此时，NPort 5110没有设置密码，故用户不用输入“Old password”，只需输入后面两项即可。
计算机的“232 to Lan.exe ”串口端的设置如下：附录：网线接法双绞线有两种接法：EIA/TIA 568B标准和EIA/TIA 568A标准。
1）T568A线序：1 2 3 4 5 6 7 8绿白绿橙白蓝蓝白橙棕白棕2）T568B线序：1 2 3 4 5 6 7 8橙白橙绿白蓝蓝白绿棕白棕直通线：两头都按T568B线序标准连接。
交叉线：一头按T568A线序连接，一头按T568B线序连接。
关于Nport 设置TCPservice模式说明书
4，设备库协议填TCP，串口类型填ip+冒号+端口如：192.168.1.248:4001，因客户端BUG，此项需要在数据库修改。如图：
5，最后，注意在loncomip配置LoaderBundle.xml，开启TCP就行。
和由于公司软件和nport虚拟串口模式常常失灵为了解决此问题特作一简单文档与大家共享之虚拟串口模式常常失灵为了解决此问题特作一简单文档与大家共享之bylisbs设置步骤以温湿度举例说明
由于
设置步骤，以温湿度举例说明：
1，登录Nport，如下图（可以通过网页以及Nport客户端）
2.从左边的树形找到Operating Setting，最上面一个常数，Operation mode选择TCP serverMode，其他ห้องสมุดไป่ตู้认即可。打开如图：
Nport5630串口服务器使用说明
Nport5630串口服务器使用说明Nport5630串口服务器是一款功能强大的设备，可以将串口设备连接到IP网络，实现远程管理和控制。
本文将详细介绍Nport5630串口服务器的使用方法和操作流程，以帮助用户更好地利用该设备。
1. 设备介绍Nport5630串口服务器是一种专门用于串口设备的远程管理和控制的设备。
它可以将串口设备转换为TCP/IP网络数据，实现远程控制和监控。
Nport5630具有多种通信接口，包括RS-232、RS-422和RS-485，可适应不同的串口设备。
2. 连接配置使用Nport5630之前，首先需要进行连接配置。
将串口设备通过串口线缆连接到Nport5630的串口接口上，同时将网络线缆连接到其以太网接口上。
确保电源供应正常，设备接口连接稳定。
3. IP设置接下来，需要对Nport5630进行IP设置。
打开终端程序，通过串口连接到Nport5630。
输入设备提供的默认IP地址和用户名密码进行登录。
进入管理界面后，选择网络设置，按照实际网络环境设置设备的IP地址、子网掩码和默认网关。
保存设置并重新启动设备，确保新的IP设置生效。
4. 端口配置配置Nport5630的串口参数，确保与连接的串口设备保持一致。
通过终端程序连接到Nport5630后，选择端口配置，设置相应的串口参数，包括串口类型、波特率、数据位、校验位和停止位等。
根据实际需求进行设置，并保存配置。
5. 远程管理完成连接配置和端口配置后，就可以通过网络远程管理和控制串口设备了。
在计算机上打开浏览器，输入Nport5630的IP地址，登录设备管理界面。
界面提供了多种功能选项，包括串口调试、远程命令、虚拟串口和数据转发等。
根据实际需求选择相应的功能，并进行相关设置和操作。
6. 串口调试Nport5630提供了串口调试功能，可以帮助用户实时监测和调试串口设备。
在设备管理界面中选择串口调试，并选择要调试的串口，打开调试窗口后，即可实时查看串口设备的输出信息。
NPort5232配置说明书
搜寻设备单击工具栏上的按钮,弹出搜寻对话框:在列表框中显示出在当前局域网络中可以找到的设备注意: 请先确定Nport设备的IP地址和服务器的IP地址处于同一网段中;配置设备在上图中对话框关闭后,在主窗体的右侧列表框中显示出该次搜寻出的设备清单:选中你需要配置的Nport设备,点击工具栏中的按钮,弹出设备配置对话框:在这里可以进行网络Ip地址的修改(使Modify选择框处于选中状态).2.端口配置对话框 OperatingMode:使Modify选择框处于选中状态,修改操作模式(OP Mode)为‘Real COM Mode’.使Modify选择框处于选中状态,修改串口的设置如上图所示,具体操作是点击列表框下面的’Settings’按钮,弹出配置对话框如下:如上图所示,配置项为: 波特率为4800,校验方式为Odd,数据位为8,停止位为1.到这里所有的配置项完成,点击配置对话框中的’OK’按钮,将配置好的参数保存,这时会出现保存进度对话框和保存完成确认框.启动驱动点击主窗体左侧树形框中的’Monitor’:点击工具栏中的按钮,添加一个Monitor后,主窗体右侧列表框中会添加一个列表项:点击工具栏中的’GO’按钮,启动Monitor.点击主窗体左侧树形框中的’Port Monitor’:点击工具栏中的按钮,添加一个Port Monitor后,主窗体右侧列表框中会添加两个列表项:点击工具栏中的’GO’按钮,启动Port Monitor.注意: 请确认’OP Mode’栏的内容为’Real COM Mode’点击主窗体左侧树形框中的’COM Mapping’:主窗体右侧列表框中会添加两个列表项:图中1的位置,’COM Port’栏的内容不一定为’COM1’,’COM2’,具体的串口号是根据当前计算机的串口配置进行显示的.图中2的位置为”4800,Odd,8,1,None”,如果不符合请点击工具栏中的进行设置.设置对话框为:。
NPORT5610串口服务器使用说明
NPORT_5610串口服务器使用说明一、串口服务器面板操作1.正面外观：左边部分一个LCD显示屏，在工作状态下，显示此串口服务器的名字和IP地址。
中间部分有4个按键（绿色的），左一为MENU左二为上，右二为下，右一为确定。
右边部分有通信指示灯。
2.背面外观：左边有一个电源开关，有一个LAN网线，连接着0A交换机，右边很多RJ45 口的是“ Serial Ports ” ,连接到TxOOA 的232 通信口。
二、在面板中进行参数设定：1、IP设定1.1、接MENU 显示Main Menu。
1.2、用上下按键滚动菜单，选择Network Setting1.3、按确定，再用上下按键滚动菜单，选择IP config1.4、按确定，选择STATIC再确定，完成此项设定，并退回到上一层菜单NetWork Setting1.5、用上下按键滚动菜单，选择IP Address,确定，进入IP地址修改。
可用上下键修改IP值。
按确定完成，并退回上一层。
1.6、NetWork Setti ng 菜单中，需要设置的参数有IP :192.168.50.252，网关192.168.50.1，掩码255.255.255.0。
修改方法雷同。
2、串口参数设定2.1、接MENU 显示Main Menu。
2.2 、用上下按键滚动菜单，选择Serial Set ，确定，进入Serial Set 菜单.2.3、Select Port用于选择被操作的物理端口。
如果需要对P2 口进行参数设定，需要在此处选择P2。
在此设定中，可以设定波特率，数据长度，较验位，停止位，FIFO 等等。
我们只需要设定好波特率，数据长度，较验位，停止位即可。
完成设定后，按确定，退回上一层。
3、参数保存用上下按键滚动菜单，选择SAVE/RESTART确定完成。
三、上位机软件的安装与配置1、运行安装包SETUP程序，按照默认安装即可。
结束安装后，运程NPORT ADMINISTRATO如下图:2、曇幵函菖审0 尊厂州华她匾干仪国象…| i野肉鏡蔭秦憧景狡3、下图为上位软件的配置环境:p快曜方克TgKknitiw快ES方式LDfTdZP砒诩医(2)矩阵挖制碾务端接收佶鸟BtmapL ZhGJOELD-066阳1MIMU* 匚DZTIUEI•迢IT>IU・CnZT4Uv4Vi.4UUU>i ■:価畑讹恤MCO2T1iUt4ViHr^ll4COZTllMlMir 理骗HtefTHtExptorct-幷山佗p.7Z&DJ役罰»*<Q■■■ffl陽惡孚BJ«ernM EJcpfefrS 服如5vte却||^^；石诂？am点击Search IP,弹出下图，并自动查找串口服务器的IP ，注意，只有同一个网段的串口服务器才能被找到。
MOXA NPort DE-211 DE-311 1-port 串行设备服务器说明书
NPort Express Series1-port RS-232/422/485serial device serversFeatures and Benefits•3-in-1serial port:RS-232,RS-422,or RS-485•Variety of operation modes,including TCP Server,TCP Client,UDP,EthernetModem,and Pair Connection•Real COM/TTY drivers for Windows and Linux•2-wire RS-485with patented Automatic Data Direction Control(ADDC®)CertificationsIntroductionThe NPort®DE-211and DE-311are1-port serial device servers that support RS-232,RS-422,4-wire RS-485,and2-wire RS-485.The DE-211 supports10Mbps Ethernet connections and has a DB25female connector for the serial port.The DE-311supports10/100Mbps Ethernet connections and has a DB9female connector for the serial port.Both device servers are ideal for applications that involve information display boards,PLCs,flow meters,gas meters,CNC machines,and biometric identification card readers.SpecificationsEthernet InterfaceNo.of Ports1Magnetic Isolation Protection 1.5kV(built-in)10/100BaseT(X)Ports(RJ45connector)DE-311:Auto MDI/MDI-X connection10BaseT(X)Ports,RJ45Connector DE-211:Auto MDI/MDI-X connectionEthernet Software FeaturesConfiguration Options Windows Utility,Telnet Console,Serial ConsoleManagement ARP,BOOTP,DHCP Client,IPv4,TCP/IP,Telnet,UDP,ICMPWindows Real COM Drivers Windows95/98/ME/NT/2000,Windows XP/2003/Vista/2008/7/8/8.1/10(x86/x64),Windows2008R2/2012/2012R2(x64),Windows Embedded CE5.0/6.0,Windows XPEmbeddedFixed TTY Drivers SCO UNIX,SCO OpenServer,UnixWare7,QNX4.25,QNX6,Solaris10,FreeBSD,AIX5.x,HP-UX11i,Mac OS XLinux Real TTY Drivers'Kernel version:2.4.x,2.6.x,3.x,4.x,Kernel version:2.6.x,Kernel version:3.x,Kernelversion:4.xAndroid API Android3.1.x and laterSerial InterfaceConnector DE-211:DB25femaleDE-311:DB9femaleSerial Standards RS-232,RS-422,RS-485No.of Ports1Baudrate Supports standard baudrates(unit=bps):50,75,110,134,150,300,600,1200,1800,2400,4800,7200,9600,19200,38400,57600,115200,230.4kData Bits5,6,7,8Stop Bits1,1.5,2Parity None,Even,Odd,Space,MarkFlow Control None,RTS/CTS,XON/XOFFRS-485Data Direction Control ADDC®(automatic data direction control)Serial SignalsRS-232TxD,RxD,RTS,CTS,DTR,DSR,DCD,GNDRS-422Tx+,Tx-,Rx+,Rx-,GNDRS-485-4w Tx+,Tx-,Rx+,Rx-,GNDRS-485-2w Data+,Data-,GNDPower ParametersInput Current DE-211:180mA@12VDC,100mA@24VDCDE-311:300mA@9VDC,150mA@24VDCInput Voltage DE-211:12to30VDCDE-311:9to30VDCReliabilityAlert Tools Built-in buzzer and RTC(real-time clock)Physical CharacteristicsHousing MetalDimensions(with ears)90.2x100.4x22mm(3.55x3.95x0.87in)Dimensions(without ears)67x100.4x22mm(2.64x3.95x0.87in)Weight480g(1.06lb)Environmental LimitsOperating Temperature0to55°C(32to131°F)Storage Temperature(package included)-40to75°C(-40to167°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class BEMS IEC61000-4-2ESD:Contact:4kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:3V/mIEC61000-4-4EFT:Power:1kV;Signal:0.5kVIEC61000-4-5Surge:Power:1kVIEC61000-4-5Surge:Power:1kV;Signal:1kVIEC61000-4-6CS:150kHz to80MHz:10V/m;Signal:10V/mIEC61000-4-6CS:150kHz to80MHz:3V/m;Signal:3V/mIEC61000-4-11DIPsMedical DE-311:EN60601-1-2Class B,EN55011Safety UL60950-1DeclarationGreen Product RoHS,CRoHS,WEEEMTBFTime DE-211:347,822hrsDE-311:225,529hrsStandards MIL-HDBK-217FWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x NPort Express Series device serverPower Supply1x power adapter,universalDocumentation1x document and software CD1x quick installation guide1x warranty cardDimensionsNPort DE-311NPort DE-211Ordering InformationModel Name Ethernet Port Speed Serial Connector Power Input Medical Certifications DE-21110Mbps DB25female12to30VDC–DE-31110/100Mbps DB9female9to30VDC EN60601-1-2Class B,EN55011Accessories(sold separately)CablesCBL-F9M9-20DB9female to DB9male serial cable,20cmApplicable Models:DE-311CBL-F9M9-150DB9female to DB9male serial cable,1.5mApplicable Models:DE-311NP21101DB25male to DB9female cable for RS-232transmission,30cmApplicable Models:DE-211NP21102DB25male to DB9male cable for RS-232transmission,30cmApplicable Models:DE-211NP21103DB25male to terminal block for RS-422/485transmissionApplicable Models:DE-211Terminal BlocksTB-M25DB25male DIN-rail wiring terminalApplicable Models:DE-211TB-M9DB9male DIN-rail wiring terminalApplicable Models:DE-311DIN-Rail Mounting KitsDK35A DIN-rail mounting kit,35mmPower AdaptersPWR-12050-WPAU-S2Non-locking barrel plug,12VDC,0.5A,100-240VAC,Australia(AU)plug,0to40°C operatingtemperaturePWR-12050-WPCN-S2Non-locking barrel plug,12VDC,0.5A,100-240VAC,China(CN)plug,0to40°C operatingtemperaturePWR-12050-WPEU-S2Non-locking barrel plug,12VDC,0.5A,100-240VAC,Continental Europe(EU)plug,0to40°Coperating temperaturePWR-12050-WPUK-S2Non-locking barrel plug,12VDC,0.5A,100-240VAC,United Kingdom(UK)plug,0to40°C operatingtemperaturePWR-12050-WPUSJP-S2Non-locking barrel plug,12VDC,0.5A,100-240VAC,United States/Japan(US/JP)plug,0to40°Coperating temperature©Moxa Inc.All rights reserved.Updated Jan18,2019.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
Moxa NPort 5100A 系列串口转Ethernet设备服务器说明书
NPort5100A系列1埠RS-232/422/485串列設備伺服器特色與優點•功耗僅1W•快速3步驟網頁式配置•具備突波保護的串列、乙太網路和電源•COM連接埠分組和UDP多播應用•螺絲式電源連接器使安裝更安全•用於Windows和Linux的Real COM/TTY驅動程式•標準TCP/IP介面及多樣化TCP和UDP操作模式•最多連接8個TCP主機認證簡介NPort®5100A設備伺服器能夠讓串列裝置立即聯網，也讓您的PC軟體在任何地方可透過網路直接存取串列裝置。
NPort®5100A設備伺服器超精巧、堅固耐用且方便使用，提供簡單且可靠的串列轉乙太網路解決方案。
更環保的串列轉乙太網路解決方案MiiNe是一款以Arm為基礎，並內嵌RAM和Flash的串列轉乙太網路SoC，體積雖小但功能強大。
因為NPort®5100A系列採用MiiNe晶片，使得功耗小於1瓦。
相較於市場上現有的解決方案，NPort®5100A系列可節省至少50%的功耗，協助工程師應對現今工業環境對於環保的要求規範。
具備突波保護的串列、乙太網路和電源突波通常是來自雷擊或設備開關間所產生的高電壓，此對電氣設備容易造成損傷。
NPort®5100A採用了Moxa領先的突波保護技術，為串列、電源和乙太網路提供完整的保護，並通過IEC61000-4-5認證標準。
這種最先進的突波保護提供堅固耐用的串列轉乙太網路解決方案，可以保護電氣裝置免於遭受電壓突波的影響並承受電氣雜訊環境條件。
僅需3步驟即可完成的網頁式配置NPort®5100A提供簡明易懂且易於使用的網頁式配置工具，只需三個步驟便可完成設置。
NPort®5100A的網頁式主控台將會引導使用者透過三個簡單的配置步驟，便可啟動串列轉乙太網路的應用。
透過這種快速3步驟網頁式配置，使用者平均只需30秒即可完成NPort®設定並啟用應用程式，從而節省大量時間和精力。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
现场调试NPORT5232
1．将电脑连入NPORT5232的网络，点击search,将会收到网络上的所有NPORT5232，根据MAC地址确定将要调试的设备。
2．双击要调试的设备。
Network是用来设置设备的IP地址，要修改必须勾选Modify ,才能操作。
Serial是用来修改485口的波特率等参数。
Operating Mode 是用来调试485口的工作模式：
TCP模式，用于以太网网络传输报文。
一般第一个485口设定4001端口，第二个485设定为4002端口。
REAL模式，将485映射到电脑，虚拟成电脑的COM口。
我们一般都在REAL模式下发送报文，以调试485总线设备（如扶梯，西门子PLC等）点击“COM Mapping”
再点击“Add”，添加我们需要映射的Nport5232，注意，我们映射的端口必须被改为REAL 模式才行。
然后点击“Apply”，选择没有占用的端口，即可（相当于电脑有了COM3，COM4等端口）。
如果端口映射不了，请关闭防火墙或杀毒软件，重新安装Nport软件。
经过如上设置，我们就可以用串口调试工具发送和接收报文了。
串口调试工具Commix 用法：双击：Commix
设定好后点击“Open Port”再在报文发送框内填写报文。
Port:设定电脑将要通讯的COM口。
（可以是Nport5232映射的端口）
输入16进制的报文，点击，Send
次窗口会显示485总线上的发送和接收的信。