驱动桥毕业设计外文翻译
驱动桥汽车外文文献翻译、中英文翻译、外文翻译
Driving Axleautomobile driving axleThe driving axle is one of cross bars supporting a vehicle, on which the driving wheels turn .The driving axle includes a housing ,an axle drive ,a differential , tow axle shafts (half axles ),and final drives (if any ) .The axle .or main, drive is a drive-line unit that increases the torque delivered by the transmission and transmits it to the driving wheels, via the differential. In automobiles, the axle drive shaft, usually called the propeller shaft.The axle drive may be a Single or a double-stage type, the former comprising a pair of gears and the latter .tow pairs of gear. Drive pinion I may be made integral with its shaft, or it may be detachable from the shaft. Driving gears and are usually made in the form of detachable gear rings that are bolted or riveted to the differential case .Alex drive bevel pinions and gears are made with helical teeth in order to reduce noise in operation.The tow-stage axle drive consists of a pair of bevel gears and a pair of spur gears. Drive bevel pinion drives bevel gear that is fixed to the flange of the intermediate shaft made integral with 2nd–stage driving spur gear .Gears meshes with driven spur gear which is fastened to the case rotates in taper roller bearings installed in the differential carrier that makes part of the driving axle housing.The differential is a drive-line unit that divides the torque applied to it between the tow axle shafts and allows one driving wheel to turn at a different speed from the other.The differential consists of case, cross or spider pinion .and side gears, also known as axle gears .the differential pinions are freely mounted on the cylindrical arms of the spider, which is held in the differential case, and remain in constant mesh with the differential side gears.When the automobile is moving down a straight and even road, both driving wheels meet with one and the same rolling resistance. In this case, axle driven gear, or differential ring gear, causes the differential case to rotate .when the differential case rotates pinions and their spider arms move around in a circle with tow differential side gears are meshed with the pinions, the side gears must rotate, causing the axle shafts and their associated driving wheels to turn. With equal resistance applied to each wheel, the differential pinions do not rotate. They apply equal torque to the side gears and therefore both driving wheels rotate at one and the same speed is unequal ,the differential pinions rotate on their spider arms as well as drive round with the differential case .supposing that one of the axle shaft is prevented from rotating ,the differential pinions would have to walk around the stationary side gear ,causing the other side gear to rotate at twice its normal speed .You can now see how the differential can allow one driving wheel to turn faster than the other .Whenever the automobile goes around a turn ,the outer driving wheel travels a greater distance than the inner drive wheel .the inner wheel speeds up proportionately ,thanks to the differential pinions that rotate on their spider arms and ,rolling around the slower side gear send more rotary motion to the outside wheel.The differential side gears are splined on to the inner ends of the axle shafts .The other ends of the shafts are attached to the driving wheel hubs by means of flanges .Trucks use full floating axle shafts .Such axle shafts are acted upon by torque only .All the other loads acting on the driving wheels are taken by the driving axle housing, because the wheel hubs are supported by bearings mounted on the housing.Driving axle of general-purpose wheeled tractorGeneral-purpose wheeled tractors are a four-wheel drive type, they have tow driving axles-front and rear .Both axles are similar in construction, expect for the housing. Each driving axle consist if a housing, an axle drive ,a differential ,and final drives .The front and rear-axles drives are interchangeable and comprise a pair of spiral bevel gears . The axle drive pinion is made integral with a shaft that issupported by tow taper roller bearings installed in axle drive pinion carrier .The latter is accommodated in differential carrier and is fixed to it by bolts. The flange of the axle drive pinion carrier is provided with threaded holes to fit puller screws that are used to remove the axle drive pinion carrier from the differential carrier .The position of the drive pinion relative to the centerline of the axle is adjust by means of a pack of shims placed under the flange of the drive pinion carrier Shims palace under the cone of the front bearing are used to adjust the preload on the drive pinion bearings. Splined to adjust the preload on the drive pinion shaft is universal-joint flange .The axle drive gear is bolted to the differential case flange.THE DIFFERENTIAL consists of case, four pinions, and tow side gears .The differential case comprise tow halves that are bolted together and supported by taper roller bearings installed in the differential carrier .Screwed in the bearings housing from the outside are nuts used to adjust the backlash between the ring gear and drive pinion teeth and the side bearing preload.Welded to the top of the driving axle housing at both its ends are spring pads .The housing of both its ends are spring axels are provided with filler ,overflow ,and drain holes closed by plugs .Both housing also have vents ,The rotating components of the driving axles are lubricated with transmission oil .As distinct from the automobiles considered in this text, all tractors include final drives in their power trains .The final drives of general-purpose wheel tractors are referred to as wheel-hub reduction gears.While transmitting power to the driving wheels, wheel-hub reduction can increase their torque .These are planetary reduction gear sets consist of sun gear ,or wheel ,three planet ,or pinion ,gears ,planet or pinion ,carrier .stationary internal ,or ring ,gear ,and housing.The sun gear is splined to the outer end of the axle shaft is splined to the differential side gear .The cylindrical planet gears are in constant mesh with both the sun gear and the ring gear and are free to rotate on roller bearings mounted on shafts that are attached to the planet carrier .The planet carrier is fasted to the reduction gear housing by means of studs and nuts .The flange of housing ,driving wheel brake drum13,and wheel hub are clamped together by bolts .The planet carrier and reduction gear housing form the driven part of the planetary gear set and rotate with the driving wheel of the tractor .The driving gear hub is supported by taper roller bearings mounted on axle shaft housing ,or axle sleeve .The axle sleeve is connected to the stationary ring gear by means of adapter hub that has internal splines and external teeth . The splines are meshed with matching splines on the axle sleeve, and the teeth are meshed with internal teeth ring gear.Wheels and its maintainModern wheeled tractors and automobiles use pneumatic-tired disc wheels. As a result of the driving wheel tires gripping the road, the rotary motion of the wheels is transformed into the translational motion of the tractor or automobile.According to their purpose, wheels are classified as driving .driven steerable, and combination types.Trucks and general-purpose wheeled tractors have all their wheels of one and the same size .Row-crop tractors have their rear wheels larger than the front wheels .The rear wheels carry the major proportion of the load due to the weight of the tractor .The front wheels are loaded lighter and this makes them easier to turn and provide good directional steering stability, which is essential for row-crop work.A TRUCK WHEEL consists of disc and flat base rim that is made integral with it, while the other flange is formed by detachable side ring that is held to the rim by split lock ring on the rim .which doubles as a side ring and a lock ring.The wheel disc is provided with holes for mounting the wheel on the wheel mounting bolts ,or wheel studs ,on the wheel hub ,where it is fixed by nuts .Both the holes and the nuts are tapered to ensure exact location of the wheel on its hub .The rear driving axles of trucks carry tow wheels at each end .The inner wheels are held to the hubs by cap nuts that are threaded both on the inside and on the outside .and the outer wheels are mounted on the cap nuts and fixed in place by taper nuts screwed on the nuts .The wheel nuts on the right side of truck have right-hand threads, whereas the nuts on the left side of the truck are threaded left-hand .The reason is to tighten the nuts, not loosen them, and thus prevent them from working loose on acceleration andbraking.An automobile pneumatic tire consists of casing, inner tube, and flap .The tire casing comprises tread, side walls, and beads .Tires for good roads use small tread patterns, while those for bad roads or cross –country service large tread patterns.The inner tube is made in the form of a hollow elastic rubber doughnut that is inflated with air after it is installed inside the tire and the tire is put on the wheel rim .The inner tube is inflated through tire valve that consists of housing 11,valve inside ,and cap .The valve housing is made of brass in the dorm of a flanged tube that is mounted in the inner tube by means of a washer and a nut and sticks out through a hole in the wheel .Some tire valve housing are of comprise construction :the upper part is made of brass and the lower part ,of rubber that is vulcanized on to the inner tube .The valve inside is a check valve that opens to let air in the inner tube when an air closed ,spring pressure and air pressure inside the tube hold the valve .When the valve is closed ,spring pressure and air pressure inside the tube hold the valve in its seat .It includes core with a rubber ring ,a plunger pin ,and a spring .The valve inside is Screwed in the tire valve housing and is closed by the cap Screwed on the housing.To the construction of the driving and steerable wheels, each wheel comprises hub , disc with rim ,and tire with inner tube .The rim is welded to the disc and the disc is bolted to the hub .The driving wheel tires are of low-pressure type and have heavy tread bars for better traction.The driving wheel hub is keyed to axle shaft and is fixed in place by means of bolted-on insert with worm whose threads mesh with the rack teeth cut in the half axle .By turning the worm one can change the position of the wheel on the axle shaft to obtain the desired track width .Before doing this ,it is necessary to jack up the rear part of the tractor to clear the wheels of the ground and loosen the bolts that hold the inserts to the wheels hubs .Should this adjustment prove insufficient ,the track width can further be increased by placing the wheels with the concaves of their discs facing inwards.On some row-crop tractors ,the rear wheel discs are bolts to lugs welded on the wheel rims .In this case ,the crack width can be changed by bolts the discs in alternative positions to the lugs .Also the concave wheel discs may be used either with the concave facing inwards or outwards.Trouble-free operation of automobiles and wheeled tractors largely depends on the condition of the tires. Therefore, during operation, one should adhere to following rules.Prevent fuel and, or oil from getting onto the tires. Cleans the tires regularly from dirt and remove all foreign articles, such as stones, form the treads. Do not apply brakes sharply, never start away form rest with a jerk, and avoid making sharp turns, for all this causes uneven wear of the tires. Do not allow excessive slipping of the driving wheels. When preparing your tractor or automobile for a long-term storage, jack up the wheels and put trestles under the axles or frame to relieve the tires.The service life of tires is expressed in terms of their mileage. For most bias (ordinary) truck tires, the guaranteed mileage amounts to 50000 km. Observing the above rules will help prolong the useful service life of tires.驱动桥汽车的驱动桥驱动桥是一个支撑车辆的十字交叉的轴，它可以驱动车轮运动。
机械毕业设计英文外文翻译基于虚拟样机技术的汽车驱动桥桥壳CADCAE系统的建立于研究
附录A 外文文献原文A1 Establish and research on CA/CAE sysytem of automobile drive axle housing based on virtual prototype technologyVirtual prototype refer to a model which is in the step of product progress, occurring in the computer realm,, aiming at the optimization based on the CAD model used to stimulating analysis product. Virtual prototype in mainly used for test which was failed by physical test. Based on the result which is drawn from the stimulation result, it is easy to modify and guide design, until reach the optimistic designAutomobile drive axle housing is a main part of a mobile. disconnect drive axle housing is used for bearing the mobile’s weight ,transferring the load to the wheels Drawing force, braking force lateral force and vertical force are transferred to frame and compartment by drive axle housing. So drive axle housing is either a bearing or a transmission item. If not correctly designed or some problem occurred while manufacturing, drive axle housing may deformed or fracture. As a traditional design method is so costly that is necessary to introduce the virtual prototype technology.A1.1 design schemeTraditional design method for drive axle housing is firstly giving a scheme ,manufacturing , a sample item then a series test (such as stiffness test bending fatigue test and static strenth test )is carried out Apparently this method is very money consuming ,and the final parameter may be not optimal .if adopt the Virtual prototype technology stimulazing kinds of working condition of drive axle housing ,and draw a series of optimal parameters .Based on these parameter the physical machine are carried out to do physical test .this method can save time ,cutting the cost ,thus bring in huge benefit to the enterprise.Modern trial production progress vary largely to the traditional one .As depicted ,in the picture ,A loop is absent in the traditional drive axle housing making virtual prototype can assess the cost quality and manufacturability on the computer. If the assessment is not satisfying, it is necessary to adjust .repeat a loop until reach a ideal parameter.This scheme design a software terrace, providing a interface for Solidworks patron and Nastron ,using superiority of this professional software ,and develop these software ,but a drive axle housing product design terrace.Considering the question of improving the analysis efficiency and simplifying finite element ,this system adopt a method which uses parametric modeling that is totally different from do make up for CAD model .And the CAD model is only used for oversightA1.2 Parameterized Modeling by SolidWorksThey are all available for second-time development of SolidWorks for the softwares that support OLE and COM. Because of design requirements, the development software of the system is Delphi and second development software of SolidWorks is OLE. The copyright of SolidWorks is 2006. To use this method, it must be registered for auto-severed including files sldworks.tlb and element files that filenames are SldWorks_TLB.pas severed by SolidWorks under Delphi program environment, and they are available after programs are complied.The topology structure of SolidWorks is typically five layers topology structure. A part is consist of bodies, and bodies include surfaces, and surfaces include edges, and edges include curves and points. It may use record in delphi to define bodies, surfaces and points these data structure and apply respectively to store topology information. The steps of the parameterized modeling of CAD by SolidWorks are as follows: firstly, it must be defined correctly for the relationship between automobile dimension and other dimensions. Secondly, initialize the various record and auto-product the drawing of axle housing using API function. Lastly, it is available for users to check the CAD model and modify various dimensions on the plate. The program can auto-modify the other relative dimensions and redraw the picture in SolidWorks by using the relationships that have been defined previously.A1.3 Patran & Nastran FEA analysisA1.3.1 PCL programMSC/PATRAN provides a fully functions program language for users, as PCL. PCL provide abundant of tables and menus and allow users to read and write all information in Patran database, which structure is similar with C language. The paper develops the analysis module of the automobile drive axle housing, which includes parameterize modeling, ALE, material definition, load cases definition, Nastran analysis submitted and results post-possessing and other functions.There are no special develop environment in PCL, generally the codes are written in test editor and saved as *.pcl format, and then the files are pre-compiled as *.cpp format in DOS, and debug them in Patran at last. The detail operates are as follows:Pre-compile *.pcl file:cpp *.pcl *.cppdebug *.cpp file in patran:!!input *.cppWhen starting, Patran will execute init.pcl file under its root catalogue. The file includes two commands:!!INPUT p3prolog.pcl and !!IPUT p3epilog.pcl. As pre-compilethese two files when Patran starts. Users can write commands to initialize Patran starting viewport. For example, write commands：!!iput C:\MSC.Software\MSC.Patran\2005_r2\ rearhouse.cpp and rearhouse.init() in p3epilog.pcl, in which, rearhouse.cpp is the second-time development program for automobile drive axle housing. It will influence the starting speed, for this, users can write self-definition functions and compile them into a database, which Patran can call directly. The method is that:Input commands in Patran:!!COMPLIE rearhouse.cpp into rearhouse.plb!!library rearhouse.plb!!llibrar keepopen rearhouse.plbAs this, Patran can load including files when it starts and the speed is rather fast. For initialize the viewport, users need to input that: rearhouse,init().A1.3.2 Program Design FlowcharThe FEA parameterize modeling part is implemented as follows:Input various key parameters into delphi, and they will be compiled and format a file whose suffix is .cpp. The contents of init.pcl can be modified by dephi. As that, users can enter Patran by click “FEA parameterize modeling” in this system, and they will see a new file, whose drawing zone has complete FEA module. The program parts don’t need to communicate with users and just like a back program. In this progress it will need API function of Windows system.Due to they require high communicate for ALE, material definition, load cases definition, Nastran analysis submitted and results post-possessing and other functions, which are not convenient for delphi to control directly, these parts will be written by PCL. Patran may copy the .CPP files to the catalog such as “C:\MSC.Software\MSC.Patra\2005_r2”, and modify the relative contents in init.pcl file.Allowing for the special features of housing modeling and computing speed of computers, the program all use shell elements to simulate housing. Therefore it use sgm_const_surface_extrude() to product shell function when modeling, and use fem_create_mesh_surf_4() to mesh when FEA meshing.A1.4 Software application exampleThis software is established by the delphi computer language. After enter the system, preliminary design of automobile drive axle housing by basis mechanics must be completed to define the key dimension, then CAE/CAD modeling and analyzing of various operating conditions should be starting. The software interface is shown in the Figure A1, Figure A2 shows the solid model of axle housing by SolidWorks parameterized modeling.Figure A1 The software interfaceFigure A2 The solid model of axle housingTable A1 illustrates material parameters whichshown in Figure A5, static of 2.5 times full load, driving by the maximum drawing force, brake of full load, turning around of full load, brake of full load in turning around. Longitudinal direction, side direction, vertical direction and revolve of longitudinal direction constraints are laid on at the center of steel plate spring. Load is laid on at the half axle casing, which resulting stress is inconsistent with actual condition, bringing no impact on stress of other parts of axle housing. The result shows that Tresca stress on wheel side is larger in Table A3.Table A2 The stress of axle housing of 5 operating conditionsin the Table A2. Figure 8 illustrates the distribution of stress nearby the steel plate spring.Figure A3 The distribution of stress nearby the steel plate spring Table A3 illustrates the former 9th order natural frequency of automobile drive axle housing by this system.Table A3 The former 9th order natural frequencybetween 1~20Hz. Resonance of axle housing won’t be caused. This result is reasonable.Figure A4 The 1st order mode of vibration附录B 外文文献中文翻译A1 基于虚拟样机技术的汽车驱动桥桥壳CAD/CAE系统的建立于研究虚拟样机是指在产品设计阶段，在计算机世界中，以优化设计思想为指导，以产品CAD模型为基础，利用各种相关CAE分析软件，进行产品主要性能仿真分析的数字模型㈣。
驱动桥汽车外文文献翻译、中英文翻译、外文翻译
驱动桥汽车外文文献翻译、中英文翻译、外文翻译The driving axle is an essential component of a ___。
It consists of several parts。
including a housing。
axle drive。
differential。
two axle shafts。
and final drives if necessary.The main purpose of the axle drive is to ___。
___.There are two types of axle drives: single and double-stage。
The single-stage type has a pair of gears。
while the double-stage type has two pairs of gears。
The drive ___ case。
To ce noise during n。
axle drive ___.In summary。
___。
It includes several components that work ___ to the wheels。
The axle drive shaft is an essential part of the axle drive。
and there are two types of axle drives。
To ce noise during n。
the driving gears are made with ___.When a car turns。
___ a greater distance than the inner ___。
thanks to the differential ns ___ around the slower side gear。
the inner ___。
汽车驱动桥设计外文文献翻译、中英文翻译、外文翻译
AppendixChina in the first half of 2008 about 93 million trucks accumulative total sales of cars, vans 61 million vehicles, year-on-year growth of 20.2%, visible light car in commercial car production has a large proportion. And driving axle is very important in the vehicle driving axle is the important car auto bearing assembly, auto frame and integral by suspension of body vertical force, to lead the longitudinal forces, transverse force and torque, and impact load; Driving axle also delivers the transmission, the maximum torque reaction is under.Automobile driving axle structure and design parameters in addition to the reliability of the automobile and durability have important influence on the outside, also for the automobile driving performance such as power, economy, smooth, through sex, mobility Automobile driving axle design involves the mechanical parts and components is widely to these varieties, spare parts, components and assemblies manufacturing also almost want to design to all modern machinery manufacturing process, design a simple structure, reliable operation and low cost, can greatly reduce the drive axle of the total cost of the vehicle production, promote economic development, and car to drive through the car studying and designing practice, can better learning and mastery of the modern car design and mechanical design of the comprehensive knowledge and skills, and the overall thinking and operation skill check, drawing, is the very important link, so ontology of a structure design of fine vans axles has certain Automobile driving axle is one of the main parts car, its basic function is to enlarge the shaft or by the torque transmission spread, then torque distribution to drive wheels, and make about driving wheel has about vehicle movement required differential function; Axles in the end of powertrain system, choose proper Lord slowdown, ensure cars than with sufficient ground clearance is achieved, gear and other transmission job need to ensure smooth are the parameters, and even bear effect on the pavement drive axle and frame or carrying body vertical force, the lead between transverse and longitudinal force and torque force. Driving axle quality, performance will have a direct impact on the vehicle's safety, economy, comfort and reliability. After the car driving axle design can make the students' comprehensive by using their This thesis research aims to overall matching car by driving axle Lord finish design of gear reducer, differential component such as type of design and calculation, and complete checking and comprehensive design single main reducer, then the batch Through the design of the vehicle driving axle should also master the understanding, including each component interaction between the body and the electricalsystem, the influence and cooperate to drive axle of the process and therefore more familiar with vehicle mastery. That in the future the production and living effectly use.附录我国2008年上半年货车累计销售约93万辆，其中轻型货车61万辆，同比增长20.2%，可见轻型汽车在商用汽车生产中占有很大的比重。
驱动桥5000字外文翻译文献
As the bearing cage rotates, read the value7. indicated on the scale.Preload normally is specified as torque re-8. quired to rotate the pinion bearing cage, so take a reading only when the cage is rotating. Starting torque will give a false reading.To calculate the preload torque, measure the 9. diameter of the bearing cage where the cord was wound. Divide this dimension in half to get the radius.10. U se the following procedure to calculate thebearing preload torque:Standard.Pull (lb) 3 radius (inches) 5 preload (lb-in.)orPreload (lb-in.) 3 0.113 (a conversion constant) 5 preload (N .m)Install the yoke, flat washer, and nut. Tighten 6. the nut snugly. Tap the end of the input shaft lightly to seat the bearings.Measure the input shaft endplay again with 7. the dial indicator. If endplay is still incorrect, repeat steps 3 through 7.With the endplay correct, seal the shim pack 8. to prevent lube leakage. Then torque the i nput shaft nut and cover capscrews to the correct value.24.5 A XLE ADJUSTMENTSAND CHECKSThis section introduces the differential carrier adjust-ments, checks, and tests that the truck technician must be capable of performing; some have beenr eferred to previously in the text. For the most part, the procedures described here are general in nature. The truck technician should refer to OEM servicel iterature for specific procedures.PINION BEARING PRELOADMost differential carriers are provided with a press-fit outer bearing on the drive pinion gear. Some older rear drive axles use an outer bearing, which slips over the drive pinion. The procedures for adjusting both types follow.Press-Fit Method AdjustmentTo adjust the pinion bearing preload using the press-fit method, use the following procedure:Assemble the pinion bearing cage, bearings, 1. spacer, and spacer washer (without drive pin-ion or oil seal). Center the bearing spacer and spacer washer between the two bearing cones (Figure 24–49).When a new gear set or pinion bearings are 2. used, select a nominal size spacer based on OEM specifications. If original parts are used, use a spacer removed during disassembly of the drive.Place the drive pinion and cage assembly in a 3. press, with the gear teeth toward the bottom.Apply and hold the press load to the pinion 4. bearing. As pressure is applied, rotate the bearing cage several times so that the bear-ings make normal contact.While pressure is held against the assembly, wind 5. a cord around the bearing cage several times.Attach a spring scale to the end of the cord 6. (Figure 24–50). Pull the cord with the scale ona horizontal line.FIGURE 24–49 Assembly of the pinion bearing cage.(Courtesy of Dana Corporation)FIGURE 24–50 Cage in press to check bearingp reload.Sleeve must applymust be against the outer bearing. If the fit between the yoke or flange splines and drive pinion splines is tight, use a press to install the yoke or flange (Figure 24–51).Temporarily install the drive pinion and cage 4. assembly in the carrier (Figure 24–52). Do not install shims under the bearing cage.Install the bearing cage to the carrier cap-5. screws. Washers are not required at this time. Hand-tighten the capscrews.Fasten a yoke or flange bar to the yoke or 6. flange (Figure 24–53). The bar will hold the drive pinion in position when the nut ist ightened.Metric.Pull (kg) 3 radius (cm) 5 preload (kg-cm) orPreload (kg-cm) 3 0.098 (a conversion constant) 5 preload (N .m)Examples. We can convert the foregoing equa-tions into examples by applying some data to them:Standard7.5 lb 3 3.31 in. 5 24.8 lb-in. (preload) or24.8 lb-in. 3 0.113 5 2.8 N .m (preload)Metric3.4 kg 3 8.4 cm 5 28.6 kg-cm (preload) or28.6 kg-cm 3 0.098 5 2.8 N .m (preload)11. I f necessary, adjust the pinion bearing preloadby changing the pinion bearing spacer. A thicker spacer will decrease preload, whereas a thinner spacer will increase the preload.12. O nce the correct bearing preload has beenestablished, note the spacer size used. Select a spacer 0.001 inch (0.025 mm) larger for use in the final pinion bearing cage assembly pro-cedures. The larger spacer compensates for slight expansion of the bearing, which occurs when pressed on the pinion shank. The trial spacer pack should result in correct pinion bearing preload in three times out of four cases.Y oke Method of AdjustmentTo adjust the pinion bearing preload using the yoke or flange method, proceed as follows:Assemble the complete pinion bearing cage 1. as recommended in the press-fit method.A forward axle pinion is equipped with a heli-2. cal gear. For easier disassembly during bear-ing adjustment procedures, use a dummy yoke (if available) in place of the helical gear.Install the input yoke or flange, nut, and 3.washer on the drive pinion. The yoke or flangeFIGURE 24–51 Using a press to install the yoke orflange to the drive pinion. (Courtesy of Arvin Meritor)FIGURE 24–52 Install the pinion and cage assembly in the carrier housing. (Courtesy of Arvin Meritor)indicated on the torque wrench (see Figure 24–55). Typical value is 50 lb-ft. (68 N .m)m aximum applied to one side gear.If the torque value exceeds the specification, 5. disassemble the differential gears from the case halves.Check the case halves, spider, gears, and 6. thrust washers for the problem that caused the torque value to exceed specifications. Re-pair or replace defective parts as required. Remove any foreign debris.Check/Adjust Pinion Cage Shim PackThis procedure is used to check and adjust the thick-ness of the shim pack used in the pinion bearing cage. Use this procedure if a new drive pinion and crownTighten the nut on the drive pinion to specifi-7. cation, typically 400 to 700 lb-ft. (542 to 950 N .m).Remove the yoke or flange bar.8. Attach a torque wrench to the drive pinion 9. nut. Rotate the drive pinion and read the value indicated on the torque wrench. Preload is correct when the torque required to rotate the pinion bearing cage is from 15 to 35 lb-in. (1.7 to 4.0 N .m).To adjust the pinion bearing preload, disas-10. semble the pinion bearing cage and change the pinion bearing spacer size. A thicker spacer will decrease preload, whereas a thin-ner spacer will increase preload.Differential Rolling ResistanceA check to measure and establish differential rolling resistance follows. To perform this check, a special tool must be made. You can easily make this tool from an old axle shaft that matches the spline size of the differential side gear. Figure 24–54 illustrates the fab-rication specifications for this special tool.To check differential resistance to rotation, use the following procedure:Install soft metal covers over the vise jaws to 1. protect the ring gear (Figure 24–55).Place the differential and crown gear assem-2. bly in the vise.Install the special tool into the differential until 3. the splines of the tool and one side gear are engaged.Attach a torque wrench to the nut of the spe-4. cial tool and rotate the differential gears. As the differential gears rotate, read the valueFIGURE 24–55 Reading the torque value to check the rolling resistance. (Courtesy of Arvin Meritor)FIGURE 24–53 Using a flange bar to hold the drivepinion in position. (Courtesy of Arvin Meritor)FIGURE 24–54 Fabrication details for a tool to checkthe rolling resistance. (Courtesy of Arvin Meritor)If the new pinion cone number is a minus (–), sub-8. tract the number from the standard shim packthickness that was calculated in step 3 or 4.The value calculated in step 7 or 8 is the 9.t hickness of the new shim pack that will bei nstalled. Figure 24–59 illustrates several e xamples of determining shim pack t hickness.Install the drive pinion, bearing cage, and new10. shim pack into the differential carrier.gear set is to be installed, or if the depth of the drive pinion has to be adjusted. You are checking the rolling resistance using a torque wrench.To check/adjust the shim pack thickness (Figure 24–56), do the following:With a micrometer, measure the thickness of 1. the old shim pack removed from under the pinion cage (Figure 24–57). Record the mea-surement for later use.Look at the pinion cone (PC) variation number 2. on the drive pinion being replaced (Figure 24–58). Record this number for later use also.If the old pinion cone number is a plus (+), 3. subtract the number from the old shim pack thickness that was recorded in step 1.If the old pinion cone number is a minus (–), 4. add the number to the old shim thickness that was measured in step 1.The value calculated in step 3 or 4 is the 5.t hickness of the standard shim pack without variation.Look at the PC variation number on the new 6. drive pinion that will be installed. Record the number for later use.If the new pinion cone number is a plus (+), 7. add the number to the standard shim packthickness that was calculated in step 3 or 4.FIGURE 24–56 Drive pinion depth controlled by shimpack thickness. (Courtesy of Arvin Meritor)FIGURE 24–57 Measuring the thickness of the old shim pack. Mike each shim individually then add tocalculate total thickness. (Courtesy of Arvin Meritor)FIGURE 24–58 Location of the pinion cone (PC)v ariation number. (Courtesy of Arvin Meritor)Adjust Differential Bearing PreloadOne of two methods can be used to check and adjust the preload of the differential bearings.Method One.Attach a dial indicator onto the mounting 1. flange of the carrier and adjust the indicator so that the plunger rides on the back surface of the crown ring gear (Figure 24–60).Loosen the bearing adjusting ring that is op-2. posite the ring gear so that a small amount of endplay is indicated on the dial indicator. To turn the adjusting rings, use a T-bar wrench that engages two or more opposite notches in the ring (Figure 24–61).Move the differential and crown gear to the 3. left and right using prybars as you read the dial indicator. Use two prybars that fit be-tween the bearing adjusting rings and the ends of the differential case (Figure 24–62). You also can use two prybars between the differential case or crown gear and the carrier at locations other than those just described. In either case, the prybars must not touch the differential bearings.EXAMPLES:Inchesmm 1.Old Shim Pack Thickness Old PC Number, PC +2Standard Shim Pack Thickness New PC Number, PC +5New Shim Pack Thickness .030.76–.002–.05.028.71+.005+.13.033.842.Old Shim Pack Thickness Old PC Number, PC –2Standard Shim Pack Thickness New PC Number, PC +5New Shim Pack Thickness .030.76+.002+.05.032.81+.005+.13.037.943.Old Shim Pack Thickness Old PC Number, PC +2Standard Shim Pack Thickness New PC Number, PC –5New Shim Pack Thickness .030.76–.002–.05.028.71–.005–.13.023.584.Old Shim Pack Thickness Old PC Number, PC –2Standard Shim Pack Thickness New PC Number, PC –5New Shim Pack Thickness.030.76+.002+.05.032.81–.005–.13.027.68FIGURE 24–59 Determining shim pack thickness.(Courtesy of ArvinMeritor Inc.)FIGURE 24–60 Dial indicator attached to carrier-mounted flange. (Courtesy of Arvin Meritor)FIGURE 24–61 Turning the adjusting ring using aT-bar wrench. (Courtesy of Arvin Meritor)FIGURE 24–62 Using pry bars to adjust play in the crown gear. (Courtesy of Arvin Meritor)Tighten the same bearing adjusting ring4.so that no endplay shows on the diali ndicator.Move the differential and crown gear to the5.left and right as needed. Repeat step 3 untilzero endplay is achieved.Tighten each bearing adjusting ring one6.notch from the zero endplay measured instep 4.Method Two.A second method of checking pre-load is to measure the expansion between the bearing caps after you tighten the adjusting rings. Use the following procedure:Turn both adjusting rings hand tight against1.the differential bearings.Measure the distance X or Y between oppo-2.site surfaces of the bearing caps (Figure24–63A) using a large micrometer of thec orrect size (Figure 24–63B). Make a note ofthe m easurement.Tighten each bearing adjusting ring one3.notch.Measure the distance X or Y again. Compare4.the dimension with the distance X or Y mea-sured in step 2. The difference between thetwo dimensions is the amount that the bear-ing caps have expanded.Example: Measurements of a carrier.Distance X or Y before tightening adjusting rings5 15.315 inches (389.00 mm)Distance X or Y after tightening adjusting rings5 15.324 inches (389.23 mm)15.324 inches minus 15.315 inches5 0.009 inch (0.23 mm) differenceIf the dimension is less than specification, repeat steps 3 and 4 as needed.Crown Gear Runout CheckTo check the runout of the crown/ring gear, do the f ollowing:Attach a dial indicator on the mounting flange1.of the differential carrier (Figure 24–64).Adjust the dial indicator so that the plunger or2.pointer is against the back surface of thecrown gear.FIGURE 24–63 (A) Location of distances measured to check expansion between bearing caps aftert ightening adjusting rings; (B) measuring this distance.(Courtesy of Arvin Meritor)FIGURE 24–64 Checking crown gear runout. (Courtesy of Arvin Meritor)Pinion and Crown Tooth ContactA djustment Correct tooth contact between the pinion and crown gear cannot be overemphasized, because improper tooth contact results in noisy operation and prema-ture failure. The tooth contact pattern consists of the lengthwise bearing (along the tooth of the ring gear) and the profile bearing (up and down the tooth). F igure 24–68 shows crown gear toothn omenclature.Adjust the dial of the indicator to zero.3. Rotate the differential and crown gear when4. reading the dial indicator. The runout of the crown gear must not exceed 0.008 inch (2 mm) (a typical value; refer to the applicable OEM service literature for the specificv alues).If runout of the crown gear exceeds the speci-5. fication, remove the differential and crown gear assembly from the carrier. Check the dif-ferential components, including the carrier, for the problem causing the runout of the gear to exceed specification. Repair or replace defec-tive components.After the components are repaired or re-6. placed, install the differential and crown gear into the carrier.Repeat the preload adjustment of the 7. differential bearings. Then repeat this runout procedure.Check/Adjust Crown Gear BacklashIf the used crown and pinion gear set is installed, ad-just the backlash to the setting that was measured before the carrier was disassembled. If a new gear set is to be installed, adjust backlash to the correct speci-fication for the new gear set.To check and adjust ring gear backlash, do thef ollowing: Attach a dial indicator onto the mounting1. flange of the carrier (see Figure 24–64).Adjust the dial indicator so that the plunger is 2. against the tooth surface at a right angle.Adjust the dial of the indicator to zero, making 3. sure that the plunger is loaded through at least one revolution.Hold the drive pinion in position.4. When reading the dial indicator, rotate the5. crown gear a small amount in both directions against the teeth of the drive pinion (Figure 24–65). If the backlash reading is not within specification (typically ranging from 0.010 to 0.020 inch or 254 to 508 mm), adjust backlash as outlined in steps 6 and 7.Loosen one bearing adjusting ring one notch 6. and then tighten the opposite ring the same amount. Backlash is increased by moving the crown gear away from the drive pinion (Figure 24–66). Backlash is decreased by moving the crown gear toward the drive pin-ion (Figure 24–67).Repeat steps 2 through 5 until the backlash is 7.within specifications.FIGURE 24–65 Check crown gear backlash. ( Courtesy of Arvin Meritor)FIGURE 24–66 Adjustments to increase backlash. (Courtesy of Arvin Meritor)the pattern in an unloaded condition (such as when you are performing this test) will be approximately one-half to two-thirds of the crown gear tooth in most models and ratios.Checking Tooth Contact Pattern on a Used Gear Set. Used gearing will not usually display the square, even contact pattern found in new gear sets. The gear will normally have a pocket at the toe-end of the gear tooth (Figure 24–71) that tails into a contact line along the root of the tooth. The more use a gear has had, the more the line becomes the dominant characteristic of the pattern.Adjusting Tooth Contact Pattern. When dis-assembling, make a drawing of the gear tooth con-tact pattern so that when reassembling it is possible to replicate approximately the same pattern. A cor-rect pattern should be clear of the toe and centers evenly along the face width between the top land and the root. Otherwise, the length and shape of the pattern can be highly variable and are usually con-sidered acceptable—providing the pattern does not run off the tooth at any time. If necessary, adjust the contact pattern by moving the crown gear and drive pinion.Checking Tooth Contact Pattern on a New Gear Set. Paint 12 crown gear teeth with a marking compound (Figure 24–69) and roll the gear to obtain a tooth contact pattern. A correct pattern should be well centered on the crown gear teeth with lengthwise contact clear of the toe (Figure 24–70). The length ofFIGURE 24–67 Adjustments to decrease backlash.(Courtesy of Arvin Meritor)FIGURE 24–68 Crown gear tooth nomenclature.(Courtesy of Dana Corporation)FIGURE 24–69 Application of a marking compoundto check tooth contact. (Courtesy of Dana Corporation)FIGURE 24–70 Correct tooth contact patternfor new gearing. (Courtesy of Dana Corporation)FIGURE 24–71 Correct tooth contact pattern for used gearing. (Courtesy of Dana Corporation)making adjustments, first adjust the pinion and then the backlash. Continue this sequence until the pattern is satisfactory.Thrust Screw AdjustmentFor those differential carriers equipped with a thrust screw, perform the following procedure. (If the carrier assembly does not have a thrust block, proceed to step 4 of this procedure.)Rotate the carrier in the repair stand until the 1. back surface of the crown gear is toward the top.Put the thrust block on the back surface of 2. the ring gear. The thrust block must be in the center between the outer diameter of the gear and the differential case.Rotate the crown gear until the thrust block 3. and hole for the thrust screw, in the carrier, are aligned.Install the jam nut on the thrust screw, one-4. half the distance between both ends (Figure 24–74).Install the thrust screw into the carrier until the 5. screw stops against the crown gear or thrust block.Loosen the thrust screw one-half turn, or 180 6. degrees.Tighten the jam nut to the correct torque value 7. against the carrier (typical values range from 150 to 295 lb-ft. or 200 to 400 N .m) (Figure 24–75).Axle TrackingAxle tracking can be measured using the older tram bar method or electronic alignment equipment. The procedures for setting axle alignment and tracking areexplained in Chapter 25.FIGURE 24–72 Two incorrect patterns when adjusting pinion position. (Courtesy of Dana Corporation)Crown gear position controls the backlash setting. This adjustment also moves the contact pattern along the face width of the gear tooth (Figure 24–72). Pinion position is determined by the size of the pinion bear-ing cage shim pack. It controls contact on the tooth depth of the gear tooth (Figure 24–73).These adjustments are interrelated. As a result, they must be considered together even though thepattern is altered by two distinct operations. WhenFIGURE 24–73 Two incorrect patterns when adjusting backlash. (Courtesy of Dana Corporation)• Most differential carriers are replaced as rebuilt/exchange units, so the role of the technician is, more often than not, to diagnose the problem and then, if necessary, to replace the defective assembly as a unit.• The technician who has disassembled and reas-sembled differential carriers should find trouble-shooting procedures easier to follow.• Follow the OEM procedure when disassem-bling differential carriers. Taking a few mo-ments to measure shim packs and gear tooth contact patterns on disassembly can save considerable time when reassembling thec arrier.• A crown and pinion gear set often can ber eused when rebuilding a differential carrier. Make sure that you inspect it properly ond isassembly.• Crown and pinion gear sets are always replaced as a matched pair during a rebuild.• When setting crown and pinion backlash, it is increased by moving the crown gear away from the drive pinion and decreased by moving the crown gear toward the drive pinion.• Adhering to OEM-recommended lubrication schedules is the key to ensuring the longest service life from both drive and dead axles.• Knowing the correct procedure to check lubricant level is essential. The level is correct when lubri-cant is exactly level with the bottom of the fill hole.• Because most OEMs approve of the use of syn-thetic lubricants in final drive carriers, lubrication drain schedules have been greatly increased in recent years. Drain schedules are determined by the actual lubricant used and the type of appli-cation to which the vehicle is subjected.• Servicing of axles on heavy-duty trucks consists of routine inspection, lubrication, cleaning, and, when required, troubleshooting and component overhaul.• Failure analysis is required to prevent recurrent failures.• Drive axle carrier components usually fail for one of the following reasons: Shock load Fatigue Spinout Lubrication problemsNormal wearFIGURE 24–74 Installing the jam nut on the thrust screw. (Courtesy of Arvin Meritor)FIGURE 24–75 Tighten the jam nut to the correct torque value. (Courtesy of Arvin Meritor)SUMMARY。
机械毕业设计英文外文翻译396驱动桥 - 副本
附录A 英文文献Drive AxleAll vehicles have some type of drive axle/differential assembly incorporated into the driveline. Whether it is front, rear or four wheel drive, differentials are necessary for the smooth application of engine power to the road.PowerflowThe drive axle must transmit power through a 90°angle. The flow of power in conventional front engine/rear wheel drive vehicles moves from the engine to the drive axle in approximately a straight line. However, at the drive axle, the power must be turned at right angles (from the line of the driveshaft) and directed to the drive wheels.This is accomplished by a pinion drive gear, which turns a circular ring gear. The ring gear is attached to a differential housing, containing a set of smaller gears that are splined to the inner end of each axle shaft. As the housing is rotated, the internal differential gears turn the axle shafts, which are also attached to the drive wheels.Rear-wheel driveRear-wheel-drive vehicles are mostly trucks, very large sedans and many sports car and coupe models. The typical rear wheel drive vehicle uses a front mounted engine and transmission assemblies with a driveshaft coupling the transmission to the rear drive axle. Drive in through the layout of the bridge, the bridge drive shaft arranged vertically in the same vertical plane, and not the drive axle shaft, respectively, in their own sub-actuator with a direct connection, but the actuator is located at the front or the back of the adjacent shaftof the two bridges is arranged in series. Vehicle before and after the two ends of the driving force of the drive axle, is the sub-actuator and the transmission through the middle of the bridge. The advantage is not only a reduction of the number of drive shaft, and raise the driving axle of the common parts of each other, and to simplify the structure, reduces the volume and quality.Fig 2 Rear-wheel-drive axle Some vehicles do not follow this typical example. Such as the older Porsche or Volkswagen vehicles which were rear engine, rear drive. These vehicles use a rear mounted transaxle with halfshafts connected to the drive wheels. Also, some vehicles were produced with a front engine, rear transaxle setup with a driveshaft connecting the engine to the transaxle, and halfshafts linking the transaxle to the drive wheels.Differential operationIn order to remove the wheel around in the kinematics due to the lack of co-ordination about the wheel diameter arising from a different or the same rolling radius of wheel travel required, inter-wheel motor vehicles are equipped with about differential, the latter to ensure that the car driver Bridge on both sides of the wheel when in range with a trip to the characteristics of rotating at different speeds to meet the requirements of the vehicle kinematics.Fig 3 Principle of differential The accompanying illustration has been provided to help understand how this occurs.1.The drive pinion, which is turned by the driveshaft, turns the ring gear.2.The ring gear, which is attached to the differential case, turns the case.3.The pinion shaft, located in a bore in the differential case, is at right angles to the axle shafts and turns with the case.4.The differential pinion (drive) gears are mounted on the pinion shaft and rotate with the shaft .5.Differential side gears (driven gears) are meshed with the pinion gears and turn with the differential housing and ring gear as a unit.6.The side gears are splined to the inner ends of the axle shafts and rotate the shafts as the housing turns.7.When both wheels have equal traction, the pinion gears do not rotate on the pinion shaft, since the input force of the pinion gears is divided equally between the two side gears.8.When it is necessary to turn a corner, the differential gearing becomes effective and allows the axle shafts to rotate at different speeds .Open-wheel differential on each general use the same amount of torque. To determine the size of the wheel torque to bear two factors: equipment and friction. In dry conditions, when a lot of friction, the wheel bearing torque by engine size and gear restrictions are hours in the friction (such as driving on ice), is restricted to a maximum torque, so that vehicles will not spin round. So even if the car can produce more torque, but also need to have sufficient traction to transfer torque to the ground. If you increase the throttle after the wheels slip, it will only make the wheels spin faster.Fig 4 Conventional differentialLimited-slip and locking differential operationFig 5 Limited-slip differential Differential settlement of a car in the uneven road surface and steering wheel-driven speed at about the different requirements; but is followed by the existence of differential in the side car wheel skid can not be effective when the power transmission, that is, the wheel slip can not produce the driving force, rather than spin the wheel and does not have enough torque. Good non-slip differential settlement of the car wheels skid on the side of the power transmission when the issue, that is, locking differential, so that no longer serve a useful differential right and left sides of the wheel can be thesame torque.Limited-slip and locking differential operation can be divided into two major categories：(1) mandatory locking type in ordinary differential locking enforcement agencies to increase, when the side of the wheel skid occurs, the driver can be electric, pneumatic or mechanical means to manipulate the locking body meshing sets of DIP Shell will be with the axle differential lock into one, thus the temporary loss of differential role. Relatively simple structure in this way, but it must be operated by the driver, and good roads to stop locking and restore the role of differential.(2) self-locking differential installed in the oil viscosity or friction clutch coupling, when the side of the wheel skid occurs when both sides of the axle speed difference there, coupling or clutch friction resistance on the automatic, to make certain the other side of the wheel drive torque and the car continued to travel. When there is no speed difference on both sides of the wheel, the frictional resistance disappeared, the role of automatic restoration of differentials. More complicated structure in this way, but do not require drivers to operate. Has been increasingly applied in the car. About non-slip differential, not only used for the differential between the wheels, but also for all-wheel drive vehicle inter-axle differential/.Gear ratioThe drive axle of a vehicle is said to have a certain axle ratio. This number (usually a whole number and a decimal fraction) is actually a comparison of the number of gear teeth on the ring gear and the pinion gear. For example, a 4.11 rear means that theoretically, there are 4.11 teeth on the ring gear for each tooth on the pinion gear or, put another way, the driveshaft must turn 4.11 times to turn the wheels once. The role of the final drive is to reduce the speed from the drive shaft, thereby increasing the torque. Lord of the reduction ratio reducer, a driving force for car performance and fueleconomy have a greater impact. In general, the more reduction ratio the greater the acceleration and climbing ability, and relatively poor fuel economy. However, if it is too large, it can not play the full power of the engine to achieve the proper speed. The main reduction ratio is more Smaller ，the speed is higher, fuel economy is better, but the acceleration and climbing ability will be poor.附录B 文献翻译驱动桥所有的汽车都装有不同类型的驱动桥和差速器来驱动汽车行驶。
机械毕业设计英文外文翻译406驱动桥设计与分析的理论研究现状
附录A 外文文献The present situation of theory research on Drive axle design and analysisWith the development of testing technology and improved driving axle in the design process to test the introduction of new technology and a variety of test equipment dedicated to carry out scientific experiments, all aspects of product structure, performance and strength of parts and components, life testing At the same time, extensive use of modern mathematical physics analysis, and assembly of products, parts and components to carry out a full technical analysis, research, and thus drive the development of bridge design theory to scientific experiments and technical analysis is based on the stage.(1) Computer Supported drive axle design and analysis of the theoretical innovation:Computer in the engineering design of the popularization and application, so that the bridge design theory-driven and technology leap in the development of completely different design process. Drive axle structure parameters and the optimization of performance parameters such as selection and matching, the intensity of components accounting and life prediction, simulation of the relevant products or simulation analysis of the art form that is more so on the choice of design and shape, design drawings Drawing will be conducted on the computer. The use of computer tools for analysis, because of its fast computing and large data capacity, we can use more accurate mathematical model of multi-degree of freedom to simulate the driving axle of the campaign in a variety of conditions, the use of modern advanced mathematics methods of analysis, can be obtained more accurate results, which analyzed for a variety of programs designed to work creatively to provide a great convenience. At present, due to the external computer equipment and the achievements of human-computer links, can be the computer's rapid calculation and logic to determine the capacity, high-capacity data storage and efficient data-processing capacity, the calculation results of dynamic image display function and creativity thinking ability and experience, the realization ofhuman-computer dialogue-style semi-automatic design, or product design expert systems, design automation. The design process can be computer-related products on a large amount of data, data retrieval, on the design of the design of high-speed computing, computer screen displays graphics and design calculations; designers can also be used up pen and direct man-machine dialogue language graphic changes to achieve the best design options, and then by computer graphics equipment line drawings drawn products. This use of computers and external devices product design methods, collectively referred to as computer-aided design. CAD and CAM will be the future into CADMAT system will show the usefulness of its huge.(2) basic studies to support the drive axle design and analysis of the theoretical innovation:With the computer design of drive axle in the popularization and application, a number of modern methods of mathematical physics and the basis for new theoretical achievements in the automotive design has become more widely used. The design of modern drive axle, in addition to traditional methods, computer-aided design methods, but also the introduction of the most optimal design, reliability, design, finite element analysis of computer simulation or simulation analysis, modal analysis and other modern design methods and analytical tools. Bridge design and analysis of drive to achieve the current high level of theory, especially the past three decades is more than a century of basic science, applied technology, materials and manufacturing processes result of continuous development and progress as well as design, production and use of long-term accumulation of experience. It is based on the production of large-scale practice, the basis of the theory as a guide to reflect the achievements of contemporary science and technology-driven bridge design software and hardware as a means to meet the needs of society for the purpose, through the use of materials, technology, equipment, tools, testing equipment, test the technical and business achievements in the field of management, continuous development and progress.(3) reverse engineering theory and methods widely used:Driving axle in the field of automated manufacturing, and often involve an enormous amount of complex design and manufacturing and testing surface. Under normal circumstances, first of all applications on the computer computer-aided design and manufacturing technology for the design of product model, and thengenerate code for processing. With the traditional processing model, compared to reverse engineering a CAD model of characterization of non-existing methods of product design, but through a variety of ways from the physical model was taken from the data re-engineering development models of a product amend. Drive the design and manufacture of axle housing is a very typical reverse engineering methods.(4) the application of rapid prototyping technology :Product innovation is designed to give full play to the designer's creative imagination, using the technical knowledge and skills to carry out the innovative ideas that the principle of a practice, its aim is to creatively design a rich and advanced new products. In the development of traditional design, the process is divided into program design, technical design, process design and product manufacturing. With the development of information technology, product design and development of the scope of the content from the traditional extended to product planning, manufacturing, testing, testing , marketing, as well as the whole process of recovery. Traditional design, the extension of the product development cycle. Rapid prototyping technology is the complete CAD model solid model layer by layer manufacturing technology, rapid prototyping technology to rid itself of the traditional processing methods, the growth of a new processing method to the complex three-dimensional processing is decomposed into a simple combination of two-dimensional processing. Therefore it does not need the use of traditional machine tools and processing tool, and only 10% of traditional processing methods of a 30% and 20% of the working hours of a 30% of the cost of products will be able to directly create and mold samples. Product innovation in the design and development application of rapid prototyping technology, with modern high-tech tools and technology to transform traditional methods of product design and development, to promote design innovation, product innovation, process innovation and management innovation to form a digital, virtual and intelligent , integrated in order to bring about a revolution in product design and development.(5) the application of concurrent engineering to product management and development:Drive Axle Industries has launched a worldwide competition designed to shorten a new product development time, reduce costs, improve quality, increasemarket competitiveness, manufacturers are increasingly becoming the most important issue to consider. Concurrent Engineering as a modern, advanced product design and development model to address these problems is a good way for countries to the automotive industry has been used. The so-called concurrent engineering, is the integrated, concurrent design of products and related processes of systems engineering, it takes from concept to product design, shape design, manufacture, use, maintenance of the entire process until the end of life of all the relevant factors that can solve the out of touch the design and manufacturing process design changes caused by frequent and long development time, cost of Higher contradictions can be designed to maximize the quality and development efficiency, and increase market competitiveness. Concurrent engineering, the key is the process of the product and its associated parallel implementation of integrated design, manufacturing and assembly-oriented design is an important aspect of concurrent engineering in product development throughout the entire process of design is the key. Innate quality of the product design decisions. Statistics show that products, including raw materials, manufacture, use, maintenance and other costs that 70% of the generalized cost is a decision from the design stage. The objectives of concurrent engineering is as much as possible early in the design stage on the introduction of the manufacture and assembly of the binding process, such as material selection, manufacturing processes, and assembly of such constraints, design changes to make as much as possible in the early stage of product development, and from manufacturing to assembly to reduce the occurrence of adverse situations, when to make a successful product design, product development to avoid the late change in design due to the enormous waste, which on the drive axle design and subAnalysis of the objectives of the theory put forward more demands.附录B外文文献的中文翻译驱动桥设计与分析的理论研究现状随着测试技术的发展与完善，在驱动桥设计过程中引进新的测试技术和各种专用的试验设备，进行科学实验，从各方面对产品的结构、性能和零部件的强度、寿命进行测试，同时广泛采用近代数学物理分析方法，对产品及其总成、零部件进行全面的技术分析、研究，这样就使驱动桥设计理论发展到以科学实验和技术分析为基础的阶段。
驱动桥的构造外文文献翻译、中英文翻译、外文翻译
附录AThe structure of driving axleThe driving axle is in the power power transmission the terminal, its basic function increases the torque which transmits by the drive shaft or the transmission gearbox, and power reasonable assignment for left and right driving gear, moreover also withstands the function vertical sets up, the longitudinal force and the transverse force between the road surface and the frame or the automobile body.The driving axle generally by the main gear box, the differential device, the wheel transmission device and the driving axle shell and so on is composed.1.Driving axle design：The driving axle design must satisfy following basic request:1). Choice main reduction gear ratios ought to be able to guarantee the automobile has the best power and the fuel economy.2). External dimensions must be small, guaranteed has the necessity ground clearance.3). Gears and other transmission piece works do steadily, the noise is small.4). Has the high transmission efficiency under each kind of rotational speed and the load.5). Under the guarantee enough intensity, the rigidity condition, should make every effort the quality to be small, under the reed the quality should be as far as possible small in particular, improves the automobile smoothness.6). Coordinated with the suspension fork guidance organization movement, regarding changes the driving axle, but also should coordinate with the rotation gear movement.7). Structures are simple, the processing technology capability is good, the manufacture is easy, disassembling, the adjustment is convenient.2.Driving axle classificationThe driving axle minute non-separation type with separates the type two big kinds.1).Non-separation type driving axleThe non-separation type driving axle also is called the integral-type driving axle, its rear axle drive pipe and main gear box shell with shaft casing rigidly connected whole Liang,thus the both sides rear axle and the driving gear swing related, passes the elastic part and the frame is connected.It by the driving axle shell 1, the main gear box, the differential device and the rear axle is composed.2). Separation type driving axleThe driving axle uses the independent suspension fork, namely the main gear box shell fixes on the frame, the both sides rear axle and the driving gear can be opposite in the rolling plane in the chassis have the relative motion to be called the separation type driving axle.In order to coordinates with the independent suspension fork, fixes the main gear box shell in the frame (or automobile body) on, the driving axle shell partition and through the hinge joint, or no longer has the driving axle shell other parts besides the main gear box shell.In order to meet the need which about the driving gear independence beats, between the differential device and between wheel rear axle each section connects with the universal joint.3.Drive axle of compositionMainly by the reducer drive, and half axle and drive axle shell, etc.1) .Main reducerThe speed reducer is usually used to change the direction of transmission, reduce speed and increase torque, guarantee cars have enough force and appropriate speed. Main reducer, have more single type, double, double speed reducer, wheel edges.a). Single main reducerBy a reduction gear reducer realization of single reducer, called. Its simple structure, light weight, dongfeng BQl090, light, medium sized truck was widely used in automobile.b). Double main reducerIn some large trucks, load demand is bigger than the slow, with single main reducer drive, driven gear diameter increases, affect to the ground clearance drive, so using twice. Usually called doublestage reducer. Two groups of double reduction gear reducer, increasing torsional twice slowdown.To improve the tapered gear pair of meshing smoothness and strength, the level of spiral bevel gears reduction gear pair is. Second gear pair is helical gears for support.Active tapered gear rotating, drive driven circular gear rotating, thus completing silver. Level Article 2 the initiative of cylindrical gears and driven tapered gear coaxial and rotate together, and bring about a follower of cylindrical gears rotate, 2. Because a follower ofcylindrical gears installed in differential shell, so, when a follower of cylindrical gears turning, through the differential and half shaft is driven wheel rotation.2).DifferentialAround half shaft are used to connect differential wheel, can make the sides with different velocity rotating torque simultaneously. Ensure the normal scroll wheel. Some more, in the car driver bridge or in the breakthrough of thansfer transmission shaft with differential between, also called the bridge between differential. Its role in the car is in turn or flat road to drive wheels, and generate differential between the role.Current domestic cars and other cars are adopted symmetric bevel gear ordinary differential. Symmetrical type gear differential planetary gear, half of planetary gear axle shaft gear, or a cross (direct axis) and differential shell, etc.Most current car using differential planetary gear, ordinary bevel gear differential by two or four conical planetary gear and planetary gear axle, two cone half shaft gear and differential shell, etc.3). Half axleHalf shaft are coming to the differential wheel, drive torque to move the car wheel rotation, the solid shaft. Due to the different structure, installation of hub axial force and the different also. Therefore, half shaft are divided into the floating, use, three/four floating three types.a). Howo fou-point suspending half axleGeneral big, medium-sized cars are adopted the floating structure. Half of the spline shaft inside with the half shaft with differential gears connected to the end of the half shaft are forging flanges, bolts and wheel connection. Hub through two far apart WenCheng tapered roller bearings in half a collar. Half a collar and driving axle shell pressure to drive, composition. Use this form, half shaft bearing no direct link with the bridge housing, half shaft driving torque and not only bear any moment under this half shaft are called "the floating" half axle. The so-called "float" means half shaft are not bending load.The float, the half axle shaft for lugs and made one. But there are some heavy trucks to lugs, and made the individual parts of the spline shaft in the half. Therefore, both ends of the spline shaft is used, can HuanTou.b). Use half axleUse of half axle within the same with the client, not withstand float bending-torsional. The client through a direct bearing on the inside of half axle shell. This means that willsupport the half axle under bending moment. Therefore, the half sleeve torque, except under bending moment, local use half shaft is called. This structure is mainly used for certain.The red flag brand limousines CA7560 type of thing. The half shaft are not bending moment, the client will inherit all external use, so called bending support.c). 3/4 floating half axleThree-quarters of floating half shaft are short of bending degree between use and the floating. This type of half axle currently used in XiaoWoChe, only on individual applications, such as M20 type car. Warsaw,4). The bridge housinga). Integral bridge housingIntegral bridge housing for the intensity and rigidity, and facilitate the good performance of the installation, adjustment and maintenance, and widely used. Integral bridge housing for manufacturing methods, which can be divided into different midway through the whole cast type, the steel casting and stamping steel welding etc.b). Drive axle shell segmentedSection type bridge housing generally fall into two, one will DuanLianCheng two by bolts. Bridge housing is segmented to casting and machining.附录B驱动桥的构造驱动桥处于动力传动系的末端，其基本功能是增大由传动轴或变速器传来的转矩，并将动力合理的分配给左、右驱动轮，另外还承受作用于路面和车架或车身之间的垂直立、纵向力和横向力。
汽车车辆类驱动桥的设计外文文献翻译、外文翻译、中英文翻译
汽车车辆类驱动桥的设计外文文献翻译、外文翻译、中英文翻译XXX毕业设计（论文）附录IDrive axle powertrain at the end of their basic function is to increase XXX, and a reasonable distribution ofpower to the left and right wheel, XXX between the vertical, XXX the main drive axle reducer, differential, XXX.The design of the Drive axle:Drive axle XXX:1. Select the main reduction ratio should be able to ensure the car has the XXX.2. Smaller size, XXX clearance.3. Gear and other pieces of the work of a smooth transmission,and small noise.4. In a variety of speed and load with a high transmission efficiency.5. XXX, XXX of small, especially under the mass-spring should be as small as possible XXX.6. And suspension movement-oriented coordination of steering drive axle, XXX.7. The structure of simple, good processing, manufacturing, easy disassembly, XXX.Drive axle classification-1-XXX毕业设计（论文）XXX-style-type with two broad categories.1. Non-disconnect-type drive axleNon-disconnect-type drive axle also known as integrated drive axle, the axlecasing and the XXX with shell shell and connected to a rigid beam,XXX with the frame components. It consists of drive axle housing 1, the mainreducer, differential and axle components.2. disconnect-type drive axle.Drive the use of independent suspension bridge, that is the main XXX vehicle chassis, on both sides of the axle and wheel in the horizontalplane as opposed to relative movement of the body is referred to as drive off thebridge.In order to match with independent suspension, the main reducer shell fixed at theframe (or body), the drive axle housing sub connected through the hinge, or inaddition to the main reducer shell outside the shell is no longer driven to other partsof the bridge. Wheel in order to meet the needs of independent jump up and down,between the differential and the wheel axle of the above connection between the useof universal joints.Drive axle componentsXXX by the main bridge reducer, differential, XXX.1. Main reducer assemblyUsed to change the main drive reducer general direction, to reduce speed andincrease torque, and ensure there is sufficient car drivers and the appropriate speed-2-XXX毕业设计（论文）skin. More types of the main reducer, a single-stage, dual-class, two-speed, such asWheel Speed Reducer.1) single-stage main reducerXXX of the devices, called single-stagereducer. Its structure is simple, light weight, such as Dongfeng BQl090 type light andmedium-sized trucks on a wide range of applications.2) two-stage main reducerLarger number of heavy-duty trucks, require a larger reduction ratio, the main useof a single-stage reducer drive, moving from gear to be XXX drive axle of the ground clearance, so the use of two XXX-stage reducer. There are two sets of two-stage reduction gear reducer, XXX.XXX, slowdown the first-class pair of XXX. Gears 2 is XXX.XXX, gear driven rotary driven round silver, XXX second stage XXX, and drive gear driven rotating cylinder, asecond-class speed. Due to the driven XXX, so that when the driven gear rotating cylinder, through the differentialand drive axle that is, the rotation of the wheels.2. DifferentialDifferential is designed to connect the axle around, on both sides of the XXX at the same time. To ensure the normal -3-XXX毕业设计（论文）XXX. Some multi-bridge-driven cars, in the sub-XXX, XXX role is to turn in the car or on uneven road surface,so that drive wheels before and after the XXX.At present, China-made cars and other types of vehicles in the basic use XXX, axle gears, planetary gear axis (cross-axis or a direct-axis) XXX of the shell and so on.XXX planet gears, planetary gearshaft, the two cone axle differential gear, and about the composition of the shell andso on.3.Auto semi-axleXXX, drive wheels spin,promote the solid axle car. As a result of the installation of wheel structure, and theforces of the axle are also different. Therefore, divided into full-floating axle,semi-floating, 3 / 4, three types of floating.1) full-floating axleGenerally large and medium-sized used car floating the whole structure. Axle withthe inner end of the XXX for the text on the axle casing. Rearaxle shell casing pressure and one pair to form the drive XXX forms, axle and axle housing no direct link so that only bear the drive-4-XXX毕业设计（论文）XXX, the axle referred to as "full-floating" axle.The so-called "floating", XXX axle.Full-floating axle, the outer end flange plate for one made with the axis. But there arealso a number of trucks to make a separate flange parts, and by XXX, at both ends of the axle spline, you can use for the first.2) semi-floating axleSemi-floating axle with the inner end of the same floating, not subject to XXX from direct client support through a bearing in the axle of theinner shell. This approach will support the outer end XXX,this short-XXX, but also to sustain the local moment, itis known as the semi-floating axle. This structure is mainly used in small passengercars.License Hongqi CA7560 icon for the type of drive axle XXX end of its moment, out client has to bear all the moment, so called semi-floatingbearing.3) 3 / 4 floating axle3 /4 XXX-floating and full floating between. At present the application of this XXX, M20vehicles.4. Automobile axle housing:1) the overall shell-style bridgeBridge shell due to the XXX, XXX, adjustment and maintenance, and XXX-5-XXX毕业设计（论文）housing due to different manufacturing methods XXX, pressed into the middle of casting XXX,XXX.2) sub-type drive axle housingSub-type XXX sections, XXX and processing easier.-6-XXX毕业设计（论文）附录II驱动桥处于动力传动系的末了，其根本功用是增大由传动轴或变速器传来的转矩，并将动力公道的分派给左、右驱动轮，别的还蒙受感化于路面和车架或车身之间的垂竖立、纵向力和横向力。
驱动桥设计外文翻译
Car drive axle design1 IntroductionThe structure form of the main reducer is based on the type of the gear and the way of the active gear and the driven gear.2 drive axleDrive axle in the tail end of the power transmission system, its basic function is to increase the torque came by the drive shaft or transmission, the reasonable distribution of power to the left and right driving wheels, and also bear role of road and the frame or body between vertical and longitudinal force and lateral force. The drive axle is composed of a main reducer, a differential, a wheel drive device and a drive axle housing.Reducer is the original motivation and independent of the working machine between the closed transmission, used to reduce speed and increase torque to meet the needs of a variety of working machinery. According to transmission form can be divided into three different for the gear reducer, worm reducer and planetary reducer; in accordance with the transmission of the series can be divided into single and multistage speed reducer; according to transmission layout situation can be divided for expansion, shunt type and coaxial type reducer. Gear reducer transmission efficiency and high reliability, long service life, maintenance is simple, and therefore the scope of application is very wide.2.1 main reducerThe main reducer gear has the spiral bevel gear type, the type of the double curved surface gear type, the type of the cylindrical gear and the worm gear and so on. At present, the main reducer gear of the automobile drive axle adopts spiral bevel gear. When the load is high, the work is stable, the noise is small, and the contact load on the tooth surface is low. So the use of single bevel gears.2.1.2 main reducer drive, driven bevel gear support formThe car driving axle design, so the use of cantilever installation. The using of the cantilever installation, ensure that the gear stiffness, active gear shaft neck should be increased, so that the distance between the two bearings than the distance of the cantilever high at least 2.5 times.3 the differential designCar in the exercise of the security, about two wheels at the same time the roll over the journey is often not equal, around two in the pressure is not equal, and the tread wear uneven, two wheel load is uneven and cause the wheel rolling radius does not match; the wheels touch the pavement conditions about different, exercises the resistance range, on the one hand will increase tire wear, power and fuel consumption, on the other hand will divert too difficult, through and handling stability is bad. Therefore, the left and right wheels of the drive axle are provided with a wheel differential mechanism.Differential is a differential transmission mechanism, used in the two output shaft torque distribution, and ensure two output shaft may rotate at different angular velocities, to ensure the driving wheels in various kinds of sports under the condition of power transmission, to avoid slipping between the tire and the ground. Differential according to its structural characteristics can be divided into gear type, convex wheel, worm wheel type and teeth embedded in a variety of forms, such as free wheel.4 half shaft For semi axis diameternot less than the diameter of the rod, the end part of the processing done slightly thicker, and appropriate to reduce spending less of the keyway depth, the tooth number must be a corresponding increase in, usually take 10 teeth (car half axle) to 18 teeth (truck half axle). The failure mode of the half shaft is basically too fatigue failure. The rod part of the axle shaft of the heavy duty truck is thicker, the outer end flange is relatively large, and the two ends of the shaft can be used as the half shaft structure with connection when no larger forging equipment is adopted, and the process is simplified by taking the same parameters. In the modern automobile half shaft, theis used quite widely, but also has the structure form of the rectangle or the trapezoidal .Shaft is one of the main parts of the machine, and all of the transmission parts of rotary motion must be installed on the axis to carry out the movement and power transmission. So the main function of the shaft is to support the rotating parts and the transmission of motion and power. According to the different load bearing, the shaft can be divided into shaft, mandrel and shaft of the third class, the relay under bending moment and bearing torque becomes the shaft. This type of shaft in the machine in the most common, only to withstand the bending moment and does not bear the torque a mandrel, the mandrel is divided into rotation and fixed mandrel mandrel two. Shaft which is only subjected to torque and does not bear the bending moment becomes the drive shaft.5 the bridge shell and the bridge shell accessories designThe main function of the drive axle housing is to support the quality of the vehicle, and is affected by the road surface reaction force and torque transmitted by the wheel, and the suspension is passed to the body. The drive shaft shell is a force transmitting member and the carrier, so the axle housing should meet the following requirements:1) with sufficient strength and stiffness, to ensure that the reducer gear mesh is normal anddoes not cause additional bending stress.2) under the premise of ensuring sufficient rigidity, as far as possible to reduce the car to improve the ride comfort.3) to ensure sufficient ground clearance.4) the structure craft is good, the cost is low.The bridge shell is a cross beam, the pivot point is located in the center of the tire, the load function in the steel plate spring seat, the average truck is used to improve the overall carrying capacity of the truck, the distance between the pivot point of the twin shaft is calculated according to the distance between the two.The maximum stress of the drive axle housing occurs near the steel plate spring. The force that causes the bending moment of the bridge shell is: the carrying capacity of the vertical load G2, the traction force F and its reaction torque M. And car shift when the tire lateral force Y2 external force in the drive axle housing, in order to simplify the calculation, just never sideslip BRDF is moving in a straight line calculated, and in terms of safety coefficient due consideration.The bending stress of the malleable cast iron bridge should not exceed 300m^2. The bending stress should not exceed 500m2 on the half shaft bushing and wheel axle of medium carbon alloy steel, and the shear stress should not exceed 250N/mm^2.Combines the actual situation of the vehicle, considering the overall expansion forming welding axle, so the material to consider ductility . We choose 16Mn.6 summaryThrough this design, it is now to design a product, only to feel that their knowledge is far from enough. There is a saying: it is never too late to learn. That's a bit of a point! Is my teacher, all my knowledge to learn!Through this design, the ability to check the manual has been greatly improved. Now, through the guidance of teachers, through their own practice, you can now go to the library to check the information, but also to look at what aspects of the information, the psychological is very clear, not so much as before.In other areas also have a lot of harvest, this graduation design makes me develop a meticulous work method. Before doing homework always give a lick and a promise, didn't have a bit of patience, sitting in the stool is not an under the heart, always with a fickle attitude to treat their own thing, now, I can very calm, very serious has been able to carry on. This may be to do the course design for me to leave things, this will be of great benefit to me later in the community.All in all, this design has made me a lot! thank you！轿车驱动桥设计1引言驱动桥处于动力传动系尾端，其基本功能是增加由传动轴或变速器传来的转矩，将动力合理分配给左、右驱动轮，且还承受作用路面和车架或车身之间的垂立、纵向力和横力。
汽车前驱动桥的结构设计毕业设计
本科学生毕业设计汽车前驱动桥的结构设计系部名称：汽车与交通工程学院专业班级：车辆工程09-12班学生姓名：xxxx指导教师：ggg职称：实验师黑龙江工程学院二○一三年六月The Graduation Design for Bachelor's DegreeThe Structural Design of The CarFront Drive Axle Candidate：Feng LiqiuSpecialty：Vehicle EngineeringClass：09-12Supervisor：Experimentalist TianfangHeilongjiang Institute of Technology2013-06·Harbin摘要随着现代车型的发展，普通汽车已经逐渐走进每一个人的生活中。
车桥设计是汽车设计中重要的环节之一，国产驱动桥在国内市场占据了绝大部份份额，但国产车桥与国际先进水平仍有必然差距，仍有必然数量的车桥依赖入口。
本次设计首先通过查阅近几年来有关国内外前驱动桥设计的文献资料，综合所学专业知识，了解并掌握了汽车前驱动桥结构及工作原理，按照所给的汽车参数制定了相应的设计方案。
然后通过查阅相关标准、手册资料，肯定了驱动桥的主要零部件的主要设计参数，完成转向器、万向节、主减速器、差速器、半轴及桥壳的结构和尺寸设计计算，并进行相应校核，再按照所计算选取的参数画出了转向驱动桥的整体装配图、差速器装配图和部份零件图。
关键词：前驱动；转向驱动桥；主减速器；差速器；半轴；桥壳ABSTRACTAs the development of the auto industry, car has gradually become part of everyone's life. Axle design is one of the important parts of automotive design, domestic drive axle in the domestic market accounted for the lion's share, but there is still a certain number of axles dependent on imports, there is still a certain gap between domestic axle and the international advanced level.Firstly, this design is lookup of the domestic and international front drive axle design documents in recent years, integrated the knowledge of our expertise we had knew and mastered the car’s front drive axle structure and working principle, formulated according to the vehicle parameters to the corresponding design programs.Then refered to the relevant standard, manual data to determine the main design parameters of the main components of the drive axle, completed the structure and size of the steering, universal joints, main gear box, differential, axle and axle housing, and check, according to the calculated parameters selected to draw the overall steering drive axle assembly drawings, the differential assembly drawings as well as some parts diagram.Key words: Front drive；Steering drive axle；Main reducer；Differential；Axle；Axle housing目录摘要 (3)ABSTRACT (4)目录 (5)第1章绪论 (1)前言 (1)概论 (1)预期的功效 (1)国内外发展状况及现状的介绍 (1)本设计的目的与意义 (3)本设计的主要内容 (3)第2章驱动桥的设计 (5)驱动桥参数 (5)驱动桥的结构方案 (5)本章小结 (7)第三章主减速器设计 (8)主减速器的结构型式 (8)主减速器的减速形式 (8)主减速器的齿轮类型 (8)主减速器主、从动锥齿轮的支承方案 (9)主减速器大体参数选择与设计计算 (9)的肯定 (9)主减速比i主减速器齿轮计算载荷的肯定 (10)主减速器齿轮大体参数的选择 (13)主减速器螺旋锥齿轮的强度计算 (17)单位齿长上的圆周力 (17)轮齿的弯曲强度计算 (18)轮齿的接触强度计算 (19)主减速器锥齿轮轴承的载荷计算与型号选择 (20)锥齿轮齿面上的作使劲 (20)锥齿轮的轴向力和径向力计算 (21)锥齿轮轴的轴径选择 (22)锥齿轮轴承载荷的计算 (22)主减速器齿轮的材料及热处置 (24)主减速器的润滑 (25)本章小结 (25)第4章差速器设计 (27)差速器齿轮大体参数选择 (28)差速器齿轮与强度计算 (32)锥形摩擦盘的设计 (32)本章总结 (35)第5章半轴设计与万向节选择 (36)半轴的型式 (36)半轴尺寸选取 (36)半轴的强度验算 (36)半轴的结构设计及材料与热处置 (38)万向节结构选择 (38)万向节的材料及热处置 (40)本章总结 (40)第6章驱动桥壳设计 (41)驱动桥壳的选择 (41)本章小结 (41)结论 (42)参考文献 (43)致谢 (44)第1章绪论前言本课题针对城市普通轿车转向驱动桥的设计。
汽车驱动桥外文文献翻译、中英文翻译、外文翻译
汽车驱动桥外文文献翻译、中英文翻译、外文翻译Drive AxleIn any vehicle。
there is always a drive ___ of whether it's a front。
rear。
or four-wheel drive。
differentials are crucial for the smooth n of engine power to the road.The drive axle must be able to transmit power through a 90-___ front-engine/rear-wheel drive vehicles。
the flow of power moves from the engine to the drive axle in a ___。
at the drive axle。
the power must be turned at a right angle (from the line of the driveshaft) and directed to the drive wheels.To do this。
a n drive gear is used to turn a ___ to the inner end of each axleshaft。
As the housing rotates。
the internal differential gears turn the axle shafts。
which are also attached to the drive wheels.二、中文翻译驱动桥所有车辆都有一种驱动桥/差速器组件集成到传动线中。
无论是前驱、后驱还是四驱，差动器都是平稳将发动机动力传递到路面上的必要条件。
驱动桥必须能够通过90度角传递动力。
在传统的前置发动机/后驱车辆中，动力流从发动机到驱动桥的方向是近似直线的。
中英文文献翻译—驱动桥相关介绍
附录附录ADriver introductions Bridge1. Features:Drive Bridge at the end of powertrain, and the basic function of which is to increase came from the drive shaft or transmission of torque, and a reasonable distribution of power to the left and right driving wheel, and also bear in the role of the frame or the road and Legislative body between the vertical, horizontal and vertical of power. Driven by the general bridge reducer, differential, wheels, transmission and drive axle housings and other components.2. The bridge design driver:（1） Drive bridge design should meet the following basic requirements:（1）. Choice of the reduction ratio should be able to guarantee that vehicles have the power and the best fuel economy.（2）. Dimensions small to ensure that the necessary ground clearance.（3）. Transmission gears and other pieces of work stable and noise.（4）. Under various load and speed with high transmission efficiency.（5）. Guarantee sufficient strength, rigidity conditions, should strive for quality small, particularly unsprung mass should be as small as possible to improve vehicle ride comfort.（6）. Oriented suspension and coordination of movement, to the drive axle, and the steering mechanism should be coordinated with campaigns.（7）. Simple structure, and processing of, and easy to manufacture, enables easy adjustment.3. Drive Bridge Category3.1 non-driving axle-disconnectDisconnect-general non-driving axle, simple structure, low cost, reliable, widely used in a variety of truck, bus and the bus, in the majority of off-road vehicles and some cars also adopt this structure. Their specific structure, in particular the shell structure while the bridge is not the same, but there is one common characteristic is that Shell is a bridge support in the drive wheel about the rigid hollow beam, and the half-axle gear transmission components, such as installation of one of them. Then the whole drive axle, drive shaft driven wheel and some are in unsprung mass, larger vehicles unsprung mass, which is one of its shortcomings.Drive Axle size depends primarily on the outline of the main types reducer. In the tire size and drive underneath the minimum ground clearance has been determined by circumstances, it defines the diameter of the driven gear reducer size. Ratio of a given condition, if the single-stage reducer can not meet the requirements of ground clearance, with the dual-class structure. In the two-stage reducer, the two usually on a main gear reducer shell reducer, can also slow gear as a second-class round-reducer. The round-reducer: In order to improve cross-country motor vehicle ground clearance, can be a spur gear consisting of round-gear reducer initiatives under its follower of the vertical top gear; buses to reduce vehicle height and the center of mass of train floors height, so as to enhance stability and the convenience of the passengers get on and off, can be round-gear reducer initiatives under its vertical driven gear beneath some double-decker bus in order to further reduce the compartment floor height in a round-Gear reducer At the same time, the main reducer and differential assembly also moved to the driver's side wheel.In a few large-scale high-speed bus engine, multi-bridge drive vehicle and ultra-heavy laden car, and sometimes used for the worm reducer, it not only has the quality of small, compact size of circumstances can be large and transmission ratio Smoothing the merits of silent work, and the overall layout of the car is very convenient.3.2-drive axle disconnectDisconnect-drive axle different from the non-driving axle-disconnect the obvious characteristics of a connection is that the former does not drive the wheels about the rigidity of the overall casing or beam. Disconnect drive bridge is the bridge sub-shell, and can be done between the relative motion, such as off-the bridge. In addition, it always match with independent suspension, it is also known as the independent suspension bridge driver. The middle of this bridge, the main reducer and differential, are mounting in the frame beamsinside or on the floor, or backbone of the frame. Lord reducer, and the driveshaft and differential wheel drive part of the quality of transmission quality on all spring. As both sides of the drive wheel independent suspension can be used to the site relative to each other frame for the upper and lower compartments or swing, with a corresponding demand on the drive wheel and the gear casing or casing for the corresponding swing.The hoisting of the type of vehicle assembly and elastic damping device components and characteristics of the work is to determine vehicle ride comfort of the main factors, and the quality of auto parts spring the size of their ride also have a marked impact. Disconnect-drive axle unsprung mass smaller, independent suspension with the match, which drive the wheels of contact with the ground and on all-terrain better adaptability, which can greatly reduce car running on uneven road vibration and the tilt train, travelling to the vehicle's ride and the average driving speed, reducing the wheels and axles on the dynamic load and parts, increasing its reliability and service life. However, due to disconnect the drive Bridge and the independent suspension with the match of the complex structure, this structure is mainly seen on the ride comfort of the higher part of sedans and some off-road vehicle, and the latter more than a light following riders Bridge drive vehicles or heavy-duty off-road vehicle.3.3 Bridge over drive layoutIn order to improve loading and adoption of some medium - and heavy-duty vehicles and all over the use of off-road vehicles are driven more bridge, and often used 4,6 × 4 × 8 × such as 6,8-driven type. Multi-Bridge driver in the circumstances, the driving force at the drive actuator pass in the way the two bridges. The two corresponding power transmission, the Multi-Bridge drive vehicle driving axle layout patterns into non-hollow and hollow. The former in order to force the pass at the drive actuator bridge to the actuator from the drive axle by its own dedicated power transmission drive shaft, not only to increase the number of drive shaft, and the cause of the drive axle Bridge parts in particular Shell, and other major parts Semiaxle not universal. On the 8 × 8 vehicle, this non-drive-through bridge is even more inappropriate, but also a difficult layout.In order to solve the above problems, modern bridges are used in cars driven through the drive axle-type layout.In the drive-through layout of the bridge, the bridge driveshaft layout in the same vertical longitudinal plane, and were not the driving axle drive shaft and use their own sub-actuator directly connected, but in front of the actuator or the back of the two adjacent bridge driveshaft is the tandem arrangement. The two ends of the car after driving axle impetus by the actuator and transmission through the middle of the bridge. The advantage is not only reduce the number of drive shaft, but also increase the driving axle parts of the mutual general, and to simplify the structure, reducing the size and quality. This vehicle design (such as car variant), manufacturing and maintenance, convenient4. Drive axle componentsDriven mainly by the main bridge reducer, differential, half-axle and drive axle housings and other components.1. Lord reducerReducer to change the general direction of transmission, reduce speed and increase torque to ensure that there are sufficient vehicles and the driving force of the appropriate speed Paper. Reducer more main types, single-stage, two-stage, two-speed, such as round-reducer.(1) single-stage main reducerBy achieving a gear reducer deceleration devices, known as a single-stage reducer. Its structure is simple, light weight, Dongfeng BQl090 type light, widely used on medium-duty truck.( 2) Two-stage main reducerSome of the larger truck load for a slowdown than larger, single-level main reducer drive, moving from the diameter of gear must be increased, it will affect the drive axle ground clearance, a two-reducer . Often referred to as the two-stage reducer. There are two double-reducing gear reducer, to the two-twisting by deceleration.To enhance the meshing of gears cone smooth and strength, the first vice-gear reducer is spiral bevel gears. Two helical gear is the result of Vice gear.Active bevel gear rotation, led a round-driven rotary gear, thus completing a slowdown. Second-class deceleration initiative Gear Driven and bevel gear and a rotating coaxial, and driven gear driven rotary cylinder, a second-class deceleration. Driven by cylindrical gear installed in the differential case, therefore, when the follower cylinder gear rotates, and through the half axle differential rotation that drive the wheels. 2. DifferentialAbout half axle differential to connect, to enable both sides of the wheels at different angular velocity of rotation torque transmission. Guarantee the normal wheels rolling. Some bridges-driven cars, in the actuator or in the hollow shaft of the transmission are available differential, known as bridge between differential. Its role in the automotive turn or uneven traffic on the road, before and after the drive wheel differential between role.At present domestic cars and other types of vehicles in the basic use of the symmetrical cone ordinary differential gear. Symmetric bevel gear from the planetary gear differential, half axle gear, planetary gear shaft (axle or a direct cross-axis) and differential shell components.Most car-use planetary gear differential, ordinary differential bevel gear cone by two or four planetary gears, gear shaft, the two conical about half axle differential gear and shell components.3. SemiaxleSemi-axle differential is the torque came to pass wheels, rotating wheel drive, and promote car travelling solid shaft. Since the installation of wheels different structures, and the force Semiaxle also different. Therefore, Semiaxle divided into floating, semi-floating, 3 / 4 floating three types.(1) Full-floating SemiaxleGenerally large and medium-sized cars are used all floating structures. Semiaxle end of the spline and with the half-axle differential gear connected to the outer end Semiaxle forging a flange, with bolts and wheels connected. Wheel through two further away from the text of Tapered Roller Bearings for the half axle casing. Semiaxle bridge shell casing pressure and after one match, composition drive axle housings. Supporting the use of such forms, and the bridge shell Semiaxle not directly linked to Semiaxle driving torque not only bear to bear any moment, such Semiaxle called the "floating" half axle. The so-called "floating" that is not half axle bending load.Floating Semiaxle all, the end-to-flange and shaft into one. But there are also some truck into separate parts of the flange, and a set of keys to spend half axle, in the end. As a result, the two ends are Semiaxle spline can be used for the first.(2) semi-floating SemiaxleSemi-axle semi-floating with all of the floating-the same does not bear bending and torsion. Aloof-supported through a direct bearing on the inside half axle casing. Supportingthis approach will bear moment Semiaxle outer end. Therefore, in addition to this Banxiu torque transmission, but also to sustain local moment, the semi-called floating Semiaxle. This structure type mainly used for small buses.(3), 3 / 4 floating Semiaxle3 /4 floating Semiaxle is subject to the degree of bending short range semi-floating and the entire floating between. Application of this type currently Semiaxle little Xiaowoche only on the individual applications, such as Warsaw M20 car.附录B驱动桥相关介绍一．功能：驱动桥处于动力传动系的末端，其基本功能是增大由传动轴或变速器传来的转矩，并将动力合理的分配给左、右驱动轮，另外还承受作用于路面和车架或车身之间的垂直立、纵向力和横向力。
CA1091货车驱动桥设计毕业设计
摘要本次毕业设计的题目是CA1091货车驱动桥设计。
驱动桥是汽车传动系统的重要组成部件 , 其位于传动系的末端，其功用是增大由传动轴或变速器传来的转矩，将其传给驱动轮并使其具有差速功能.所以中型专用汽车驱动桥设计有着实际的意义。
在本次设计中，根据当今驱动桥的发展情况确定了驱动桥各部件的设计方案。
本次设计的车型为解放CA1091汽车主减速器的形式采用单级主减速器；而差速器则采用目前被广泛应用的对称式锥齿轮差速器；其半轴为全浮式支撑。
在本次设计中完成了对主减速器、差速器、半轴、桥壳及轴承的设计计算及校核。
并通过以上计算满足了驱动桥的各项功能。
此外本设计还应用了较为先进的设计手段，如用 MATLAB进行计算编程和用CAXA软件绘图。
本设计保持了驱动桥有足够的强度、刚度和足够的使用寿命，以及足够的其他性能。
并且在本次设计中力求做到零件通用化和标准化。
关键词：驱动桥、主减速器、差速器、半轴、桥壳AbstractThe graduation project is the subject of a medium goods vehicle driver in the design of the bridge. Bridge drive vehicle drive system is an important component parts, its function is increasing drive shaft or transmission came from the torque, andits transmission to a driving wheel differential function. So medium-sized private car driver has a practical bridge design Significance.In the design of the bridge under the current drive the development of the driver identified the components of the bridge design. According to the design of this modelfor the medium-sized cars, so the main reducer in the form of a two-stage main reducer, and the current differential is being widely used symmetric bevel gear differential; its axle for the whole floating - Support. In the completion of the design of the main reducer, differential and axle, bearings and the bridge shell calculation and design verification. Through the above calculation and the drive to meet the various functions of the bridge. In addition the design of a more advanced design tools, such as MATLAB calculated using CAXA software programming and graphics.This design has maintained a drive axle have sufficient strength, stiffnessand sufficient life, and enough other properties. And in this design-to-commonand standardized components.Key words：Drive Bridge, the main reducer, differential and axle, Shell Bridge目录第一章绪论 (1)1.1驱动桥简介 (1)1.2驱动桥设计的基本要求 (1)第二章驱动桥主减速器设计 (3)2.1主减速器简介 (3)2.2主减速器形式的选择 (3)2.3主减速器锥齿轮的选择 (4)2.4主减速器齿轮的支承 (5)2.5主减速器轴承的预紧 (6)2.6锥齿轮啮合的调整 (6)2.7润滑 (7)2.8双曲面锥齿轮的设计 (7)2.8.1主减速比的确定 (7)2.8.2主减速器齿轮计算载荷的确定 (8)2.8.3主减速器齿轮基本参数的选择 (9)2.9主减速齿轮的材料及热处理 (20)第三章驱动桥差速器设计 (21)3.1差速器简介 (21)3.2差速器结构形式的选择 (21)3.3差速器齿轮的基本参数选择 (23)3.4差速器齿轮的几何尺寸计算与强度校核 (25)第四章车轮传动装置的设计 (28)4.1车轮传动装置的功用 (28)4.2半轴支承型式 (28)4.3全浮式半轴计算载荷的确定 (28)4.4半轴的强度计算 (28)4.5全浮式半轴杆部直径的初选 (29)4.6半轴的结构设计及材料与热处理 (29)第五章驱动桥壳设计 (30)5.1驱动桥壳的功用和设计要求 (30)5.2 驱动桥壳结构方案分析 (30)结论 (31)参考文献 (32)致谢 (33)附录 1 (34)第一章绪论1.1 驱动桥简介驱动桥是汽车传动系的重要组成部分，它位于传动系的末端，一般由主减速器、差速器、车轮传动装置和桥壳等组成。
重型商用车驱动桥设计翻译
华南理工大学广州汽车学院本科生毕业设计（论文）翻译英文原文名DRIVE AXLE ASSEMBLIES中文译名驱动桥系别汽车工程系专业班级车辆工程学生姓名陈威指导教师上官文斌填表日期2011-5-19二〇一一年五月英文原文版出处：Dirk Spindler Georg von Petery INA-Schaeffler KG. Angular Contact Ball Bearings for a Rear Axle Differential.SAE ，2003译文成绩：指导教师（导师组）签名：译文：驱动桥在学习本章之后，你将了解不同类型驱动桥的组成，并能列举不同种类的驱动桥；比较后桥与前桥的不同之处；描述驱动桥的工作原理。
驱动桥有很多重要作用。
它可以使车轮回正，控制车轮滚动，可以使其中一个车轮的转速比另外一个车轮快，两个车轮均可获得转矩。
驱动桥可以获得来自于车轮的反作用力，通过弹簧，操纵杆等将作用力传到车架上。
驱动桥在车轮制动器被安装的基础上通过弹簧来固定，并获得簧上质量。
很显然，驱动桥需要使用高质量的材料来制作。
结构后桥的几个基本组成部分：桥壳，半轴，差速器。
桥壳桥壳通常是由钢板模压件焊接在一起而制成的。
桥壳的中心部分是由铸钢制成的。
有两种类型的桥壳常被使用：整体式桥壳（应用广泛）和分段式桥壳（应用较少）是由两个或者更多的部分组成。
车桥两个车桥在桥壳的内部，它们在内部相接触，在某些位置它们是不接触的。
外部的凸出端附在车轮和轮毂上。
内部端被花键固定在差速器上，外端被滚子轴承所固定。
连接轮两种方法被应用于驱动桥的轮毂上。
一种方法是在驱动桥一端用拔销来固定，另一端通过凸缘固定。
半轴的类型半轴有三种基本的类型，全浮式， 3/4浮式和半浮式。
大多是汽车采用半浮式，大部分货车采用全浮式半轴支承。
如果半轴折断，车轮将停止转动。
驱动桥汽车转弯时的工况与普通行驶时的不同，必须使用一个叫做差速器的单元使两个半轴都获得动力，让左右驱动车轮的行驶速度不同。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
毕业设计/论文外文文献翻译系别自动化系专业班级机械电子工程0603班姓名评分指导教师2010 年4月29日毕业设计/论文外文文献翻译要求：1．外文文献翻译的内容应与毕业设计/论文课题相关。
2．外文文献翻译的字数：非英语专业学生应完成与毕业设计/论文课题内容相关的不少于2000汉字的外文文献翻译任务（其中，汉语言文学专业、艺术类专业不作要求），英语专业学生应完成不少于2000汉字的二外文献翻译任务。
格式按《华中科技大学武昌分校本科毕业设计/论文撰写规范》的要求撰写。
3．外文文献翻译附于开题报告之后：第一部分为译文，第二部分为外文文献原文，译文与原文均需单独编制页码（底端居中）并注明出处。
本附件为封面，封面上不得出现页码。
4．外文文献翻译原文由指导教师指定，同一指导教师指导的学生不得选用相同的外文原文。
驱动桥设计随着汽车对安全、节能、环保的不断重视，汽车后桥作为整车的一个关键部件，其产品的质量对整车的安全使用及整车性能的影响是非常大的，因而对汽车后桥进行有效的优化设计计算是非常必要的。
驱动桥处于动力传动系的末端，其基本功能是增大由传动轴或变速器传来的转矩,并将动力合理地分配给左、右驱动轮，另外还承受作用于路面和车架或车身之间的垂直力力和横向力。
驱动桥一般由主减速器、差速器、车轮传动装置和驱动桥壳等组成。
驱动桥作为汽车四大总成之一，它的性能的好坏直接影响整车性能，而对于载重汽车显得尤为重要。
驱动桥设计应当满足如下基本要求：1、符合现代汽车设计的一般理论。
2、外形尺寸要小，保证有必要的离地间隙。
3、合适的主减速比，以保证汽车的动力性和燃料经济性。
4、在各种转速和载荷下具有高的传动效率。
5、在保证足够的强度、刚度条件下，力求质量小，结构简单，加工工艺性好，制造容易，拆装，调整方便。
6、与悬架导向机构运动协调，对于转向驱动桥，还应与转向机构运动协调。
智能电子技术在汽车上得以推广使得汽车在安全行驶和其它功能更上一层楼。
通过各种传感器实现自动驾驶。
除些之外智能汽车装备有多种传感器能充分感知交通设施及环境的信息并能随时判断车辆及驾驶员是否处于危险之中，具备自主寻路、导航、避撞、不停车收费等功能。
有效提高运输过程中的安全，减少驾驶员的操纵疲劳度，提高乘客的舒适度。
当然蓄电池是电动汽车的关键，电动汽车用的蓄电池主要有：铅酸蓄电池、镍镉蓄电池、钠硫蓄电池、钠硫蓄电池、锂电池、锌—空气电池、飞轮电池、燃料电池和太阳能电池等。
在诸多种电池中，燃料电池是迄今为止最有希望解决汽车能源短缺问题的动力源。
燃料电池具有高效无污染的特性，不同于其他蓄电池，其不需要充电，只要外部不断地供给燃料，就能连续稳定地发电。
燃料电池汽车(FCEV)具有可与内燃机汽车媲美的动力性能，在排放、燃油经济性方面明显优于内燃机车辆。
另外，设计必须得考虑所选择材料的可加工性能。
一种材料的可机加工性通常以四种因素的方式定义：1、分的表面光洁性和表面完整性。
2、刀具的寿命。
3、切削力和功率的需求。
4、切屑控制。
以这种方式，好的可机加工性指的是好的表面光洁性和完整性，长的刀具寿命，低的切削力和功率需求。
关于切屑控制，细长的卷曲切屑，如果没有被切割成小片，以在切屑区变的混乱，缠在一起的方式能够严重的介入剪切工序。
因为剪切工序的复杂属性，所以很难建立定量地释义材料的可机加工性的关系。
在制造厂里，刀具寿命和表面粗糙度通常被认为是可机加工性中最重要的因素。
尽管已不再大量的被使用，近乎准确的机加工率在以下的例子中能够被看到。
通常，零件的可机加工性能是根据以下因素来定义的：表面粗糙度，刀具的寿命，切削力和功率的需求以及切屑的控制。
材料的可机加工性能不仅取决于起内在特性和微观结构，而且也依赖于工艺参数的适当选择与控制。
拖臂悬架结合起来的一种行为,semi-trailing-arm落后表现出轴。
它是用来驱动的汽车前面。
如果轴经验,它就像一卷悬垂态的手臂。
扭转刚度的摩天大楼,这活象一个stabiliser酒吧。
如果两个轮子的旅行经历相同的悬架(例如在球场的汽车)轴表现得像个拖臂悬架。
梁式轴(Four-Link-Style)前面的一辆汽车后轴,不必有相同的高度为他们的卷中心。
辊轴轴线上,这是经过辊子的中心——和后轴,看到前面的图。
辊轴如果一个横向力的重心,导致层(fom)上面的重心轴的卷必须补偿片刻所致。
由于一些弹簧悬辊。
这一刻之间分配方面和后桥有赖于相对弹簧刚度的前面,与后轴,整体侧倾角(这是一样的,和后轴)取决于总和的悬架刚度(前加上后方)。
传送到地面的瞬间,没有任何卷的整体车辆通过应用侧向力轴向前滚动的位置(在CG)。
(注:如果滚动的轴,剩下的扭矩,CG必须补偿汽悬泉会像一辆摩托车内倾斜。
这一幕的分布与后轴会,计算了分别计算各轴的位置,by-using相应的axle-using卷中心的一部分的事实,轮轴横向力所承受的一部分,与正常负荷、轮轴必须随身携带不同的例子一个有限的特点,防滑差速器有点不同,不同的风格，一个自锁装置。
这个Torsen®风格差异;(从扭矩遥感)行为非常快(并可能严厉的)。
在较低的输入扭矩的差动齿轮只是轻轻负载和移动，自由敞开的装置。
随着力矩和速度起落架网格，大米和两个输出轴锁在一起。
扭矩比(high-torque-wheel除以low-torque-wheel)不等,2.5:1 max。
7:1,Torsen II的风格，从3:1来1.8:1(根据齿轮,齿轮表面处理的角度,类型的滚子轴承(平原,…)达纳Trac-Loc®limited-slip差的(见图)包含一些预紧通过弹簧离合器片、贝尔维尔)提供了一定的静态启动扭矩已经在零输入扭矩。
蜘蛛齿轮,齿轮啮合侧设计那样(楔形齿),增加输入扭矩将增加的负担,提高离合器盘的锁轴。
独立的粘性微分锁的扭矩,但反应速度与输出轴之间的差异。
包括离合器片没有机械接触,但是很紧的间隙,使粘滞摩擦提供扭矩的转让。
注意,粘稠的差距在很光滑,有一定的时间延迟,作为粘度增加与所产生的热量(指的是特殊的液体是合宜的齿厚)。
这使得操作容易使用汽车(虽然可以街是太慢了有些应用)。
Design of driving axleAs the car to safety, energy saving, the constant attention to environmental protection, vehicle after vehicle bridge as a key component, the quality of their products on the safe use of cars and car performance of a very large, so the car after Bridge Effectively optimize the design and calculation is very necessary.Drive Bridge at the end of powertrain, its basic function is to increase came from the drive shaft or transmission of torque and power reasonably allocated to the left and right driving wheel and also bear in the role of the road and trailers or Body of power between the vertical and horizontal force. Drive from the main bridge general reducer, differential and the wheels, transmission and drive axle components, such as Shell. Bridge drive a vehicle with one of the four trains, its performance will have a direct impact on vehicle performance, and it is particularly important for the truck. Drive bridge should be designed to meet the following basic requirements:a) a suitable main slowdown than to ensure that the car from the best power and fuel economy.b) small form factor to ensure that the necessary ground clearance.c) transmission gears and other parts of a smooth, noise.d) in various load and speed of transmission with high efficiency.e) to ensure adequate strength, stiffness conditions, should strive for the quality of small, in particular the quality of the spring as possible, to improve the car ride.f) suspension and body-oriented movement coordination, the drive to the bridge, should also be coordinated with the campaign steering mechanism.g) simple structure, processing technology and good, easy to manufacture, enables easy adjustment..Intelligent electronic technology in the bus to promote safe driving and that the other functions. The realization of automatic driving through various sensors. Except some smart cars equipped with multiple outside sensors can fully perception of information and traffic facilities and to judge whether the vehicles and drivers in danger, has the independent pathfinding, navigation, avoid bump, no parking fees etc. Function.Effectively improve the safe transport of manipulation, reduce the pilot fatigue, improve passenger comfort. Of course battery electric vehicle is the key, the electric car battery mainly has: the use of lead-acid batteries, nickel cadmium battery, the battery, sodium sulfide sodium sulfide lithium battery, the battery, the battery, the flywheel zinc - air fuel cell and solar battery, the battery. In many kind of cells, the fuel cell is by far the most want to solve the problem of energy shortage car. Fuel cells have high pollution characteristics, different from other battery, the battery, need not only external constantly supply of fuel and electricity can continuously steadily. Fuel cell vehicles (FCEV) can be matched with the car engine performance and fuel economy and emission in the aspects of superior internal-combustion vehicles.Keyword: drive axle differential bridge reducer Bridge shellThis is an ANSYS optimum design for driving axle housing of a off-road vehicle. Firstly, the author established a three-dimensional model of the driving axle. States of stress in different working conditions were analyzed. Furthermore, the maximum pressure of driving axle was achieved.And then, the three-dimensional model was imported into ANSYS, with some other manipulations, such as meshing, adding degree of freedom, applying surface loads, etc. States of stress of driving axle were calculated with the results exported.Finally, this paper carried out the optimum design according to the target of minimizing the qualitative properties and homogenizing the distribution of stresses. The Confirmatory analysis showed that this design measured up to the engineering requirement.MACHINABILITYThe machinability of a material usually defined in terms of four factors:1、Surface finish and integrity of the machined part;2、Tool life obtained;3、Force and power requirements;4、Chip control.Thus, good machinability good surface finish and integrity, long tool life, and low force And power requirements. As for chip control, long and thin (stringy) cured chips,if not broken up, can severely interfere with the cutting operation by becoming entangled in the cutting zone.Because of the complex nature of cutting operations, it is difficult to establish relationships that quantitatively define the machinability of a material. In manufacturing plants, tool life and surface roughness are generally considered to be themostimportant factors in machinability. Although not used much any more, approximate machinability ratings are available in the example below.SUMMARYMachinability is usually defined in terms of surface finish, tool life, force and power requirements, and chip control. Machinability of materials depends not only on their intrinsic properties and microstructure, but also on proper selection and control of process variables.A combination of trailing- and semi-trailing-arm behaviour shows the following axis. It is used for front driven cars only. If the axle experiences roll, it behaves like asemi-trailing arm. The torsional stiffness counteracts the roll, by this acting like a stabiliser bar. If both wheels experience the same suspension travel (e.g. during pitch of the car) the axle behaves like a trailing arm suspension.Beam Type Axle (Four-Link-Style)Front- and rear-axle of a car needn't have the same hight for their roll center. The roll axis is that axis, that goes through the roll center of front- and rear-axle, see following drawing:Roll AxisIf a lateral force is applied at the center of gravity, the moment resulting fom the hight ofthe center of gravity above the roll axis has to be compensated by a moment caused by thesuspension springs due to some roll. The distribution of this moment between front- and rear axle depends on the relative spring stiffness of front- and rear-axle, the overall roll angle (which is the same for front- and rear-axle) depends on the sum of the suspension stiffness (front plus rear).The moment transmitted to the ground without any roll for the overall vehicle is given bythe applied lateral force times the roll axis hight (at the position of CG). (Remark: If theroll axis is above the CG, the remaining torque that has to be compensated by the suspension springs would make the car lean inside like a motorcycle!).The distribution of this moment between front- and rear-axle can be calculated by calculating each axle seperately, by-using the position of the roll center of the corresponding axle-using the fact that the part of lateral force, that the axle has to carry,corresponds to the part of thenormal load, the axle has tocarryDifferential ExamplesThe characteristics of a limitedslip differential are a little bitdifferent for different stylesof a self-locking device.The Torsen® styledifferentials (from TORqueSENsing) act very fast (andpossiblyharsh). Under low input torque the differential gears are only lightly loaded and movefreely like an open device. With increasing torque (and speed) the gear meshes are loaded up and the two output shafts are locked together. The torque ratio(high-torque-wheel divided by low-torque-wheel) varies from max. 7:1 to 2.5:1, for the Torsen II stylefrom 3:1 to 1.8:1 (depending on gear angles, gear surface treatment, type ofbearing(plain, roller...)The Dana Trac-Loc® limited-slip differential (see picture below) contains some preloaded(by Belleville springs) clutch plates, which provide a certain static breakout torque already at zero input torque. The spider gear and side gear mesh are designed in that way (with wedge-shaped gear teeth), that increasing input torque will increase the load on the clutch plates, by this increasing the locking of the axle.Dana Trac-Loc® limited-slip differentialThe viscous differential locks independent of of torques, but reacts to the speed differences between the output shafts. The contained clutch plates have no mechanical contact, but very tight clearances, so that the viscous friction provides the torque transfer. Note that viscous differentials set in very smooth, and with a certain time delay, as theviscosity increases with thegenerated heat (means the specialfluid is becoming'thicker'). This makes thehandling easier for street use cars(while may be too slow forsome racing applications).11。