船舶专业英语词汇
有关船舶的英文专业术语
“Maritime Terminology: Essential Vocabulary for Ships”1.Bow: The front part of the ship.2.Stern: The back part of the ship.3.Port: The left side of the ship when facing forward.4.Starboard: The right side of the ship when facing forward.5.Hull: The main body of the ship, excluding superstructure and machinery.6.Deck: The horizontal surface of a ship where people walk or work.7.Bridge: The navigational control center of the ship, usually located at the front.8.Bulkhead: A partition wall within the hull of the ship.9.Keel: The central structural member of the ship’s hull, running along the bottom.10.Rudder: A movable device used to steer the ship.11.Propeller: A rotating device that propels the ship through the water.12.Mast: A vertical structure on the ship that supports sails or antennas.13.Bilge: The lowest compartment on a ship’s hull, often prone to collecting water and otherliquids.14.Ballast: Weight added to a ship to improve stability or adjust draft.15.Cargo Hold: A space within the ship’s hull for storing cargo.16.Anchor: A heavy object deployed to keep the ship stationary.17.Windlass: A machine used for raising and lowering the anchor.18.Lifeboat: A small boat carried by a ship for use in emergencies.19.Buoy: A floating object used for navigation or marking hazards.20.Chart: A map used for navigation, showing water depths, landmarks, and other relevantinformation.These are just a few examples of the many specialized terms used in the maritime industry. Understanding these terms is essential for effective communication and safe operation aboard ships.。
船舶英语词汇
船舶专用词汇1.船舶的分类passenger ship 客船general cargo ship 杂货船bulk cargo carrier 散货船container ship 集装箱船roll on/roll off ship 滚装船tanker 油船liquid gas carrier 液化气船barge 驳船barge carrier 载驳船dredger 挖泥船floating crane 起重船floating dock 浮船坞ice breaker 破冰船drilling platform 钻井平台drilling ship 钻井船trawler 拖网渔船stern ramp trawler 尾滑道拖网渔船tug boat 拖船fire boat 消防船ocean survey ship 海洋调查船cruiser 巡洋舰destroyer 驱逐舰frigate 护卫舰aircraft carrier 航空母舰submarine 潜艇hydrofoil craft 水翼艇air cushion vehicle 气垫船—hovercraft 全浮式气垫船—sidewall air cushion vehicle 侧壁式气垫船small waterplane area twin hull ship 小水线面双体船semi-submerged catamaran 又称为半潜双体船2.船体结构longitudinal bending 总纵弯曲hogging 中拱弯曲sagging 中垂弯曲longitudinal strength 总纵强度transverse strength 横向强度local strength 局部强度hull 船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 艏楼bridge 桥楼poop 艉楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁fore peak bulkhead 艏尖舱舱壁after peak bulkhead 艉尖舱舱壁3.外板和甲板板shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 船底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板upper deck 上甲板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板4.船底结构center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 钢板折边法兰bilge bracket 舭肘板floor 肋板solid floor 主肋板watertight floor 水密肋板bracket floor 框架肋板lightened floor 轻型肋板stiffener 加强筋扶强材bulb plate 球扁钢angle bar 不等边角钢bottom center girder 中底桁bottom center girder 旁底桁duct keel 箱形中底桁pipe tunnel 管隧reverse frame 内底横骨bottom frame 船底肋骨longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨inner bottom plate 内底板margin plate 内底边板man hole 人孔bilge well 污水井bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 艉室emergency exit 应急通道bilge keel 舭龙骨5.舷侧结构Integrated barge 分节驳frame 肋骨main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材6.甲板结构beam 横梁deck beam 普通横梁hatch end beam 舱口端横梁deck girder 甲板纵桁side stringer 舷侧纵桁hatch side girder 舱口纵桁beam knee 梁肘板sponson deck 舷伸甲板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 货舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁pillar 支柱topside tank 顶边舱excess hatch 出入舱口expansion trunk 膨胀井7.舱壁结构bulkhead 舱壁cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical stiffener 垂直扶强材8.首尾端结构vertical bow 直立型艏raked bow 前倾型艏clipper bow 飞剪型艏ice breaker bow 破冰型艏elliptical stern 椭圆形艉cruiser stern 巡洋舰型艉transom stern 方形艉fore peak艏尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱breast hook 艏肘板stem 艏柱steel plate stem 钢板艏柱forged steel stem 锻钢艏柱combination cast and rolled stem 混合式艏柱tunnel 管隧thruster 侧推器after peak 艉尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame 艉柱shoe piece 艉柱底骨rudder post 舵柱propeller post 螺旋桨柱propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架9.上层建筑和机舱棚结构accommodation 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass platform 罗经平台expansion joint 伸缩接头derrick post桅杆derrick platform 起货机平台tower post 塔式桅stern door 艉门bow door 艏门visor type 罩壳式side hinged type 边铰链式pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱ballast water tank 压载水舱conning tower sail 指挥台围壳渔业船舶种类2.1 渔船fishing vessel 用于商业性捕捉鱼类、鲸、海豹、海象或其他生物资源的船舶之统称。
船舶工程专业英语词汇
船舶专业英语词汇（按照字母顺序排列）（一）a faired set of line apair of stereo 片abaft 朝向船体abandonment costaccommodationaccommodationladder 舷梯adjustvalve 调节阀adjustable-pitch 可调螺距式admiralty 海军部，海事法，制海权，海军上将advance coefficient 进速系数，前进系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli 'law s 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索经过光顺处理的一套型线photographs 一对立体投影相船舶废置成本费用居住（舱室）air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍butt weld 对缝焊接 butterfly screw cap 蝶形螺帽 buttock 后体纵剖线 by convention 按照惯例，按约定 船舶专业英语词汇(按照字母顺序排列) (二)cable ship 布缆船 cable winch 钢索绞车 CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计 算 机 辅助制造 CAM(computer-aided engineering) 计算机辅助 工程camber 梁拱 cant beam 斜横梁 cant frame斜肋骨cantilever beam 悬臂梁 capacity plan 舱容图 CAPP(ComPUter -aided ProCeSS Pla nning) 计算机辅助施工计划制定CaPSize 倾覆 CaPSizing moment 倾覆力臂CaPtain 船长CaPtUred-air-bUbble vehiCle 束缚气泡减阻船Cargo CUbiC 货舱舱容，载货容积Cargo handling 货物装卸 Carriage 拖车，拖架 CaSt Steel Stem PoSt 铸钢艏柱Catamaran 高速双体船 Catamaran双体的Cavitation 空泡 Cavitation nUmber 空泡数 Cavitation tUnnel空泡水筒Center keelSon 中内龙骨 Centerline bUlkhead中纵舱壁Centroid 型心，重心，质心，矩心 Chain Cable StoPPer 制链器Chart 海图 Charterer 租船人 Chief engineer 轮机长Chine 舭，舷，脊 ChoCk 导览钳CIM(ComPUter integrated manUfaCtUring) 计算机集成组合制造bobstay 首斜尾拉索 body plan 横剖面图bolt 螺栓，上螺栓固定 Bonjean curve 邦戎曲线boom 吊杆 boss 螺旋桨轴榖 bottom side girder旁底桁 bottom side tank 底边舱 bottom transverse底列板boundary layer 边界层 bow line 前体纵剖线 bow wave 艏波 bowsprit 艏斜桅 bow-thruster 艏侧推器 box girder 箱桁 bracket floor 框架肋板brake 制动装置 brake band 制动带 brake crank arm 制动曲柄brake drum刹车卷筒brake hydraulic cylinder 制动液压缸 brake hydraulic pipe 刹车液压管 breadth extreme 最大宽，计算宽度 breadth moulded型宽breakbulk 件杂货 breasthook 艏肘板 bridge 桥楼，驾驶台 bridge console stand 驾驶室集中操作台 BSRA 英国船舶研究协会 buckle 屈曲 buffer spring 缓冲弹簧 built-up plate section组合型材bulb plate 球头扁钢 bulbous bow 球状船艏，球鼻首 bulk carrier 散货船 bulk oil carrier 散装油轮 bulkhead 舱壁 bulwark 舷墙 bulwark plate舷墙板 bulwark stay 舷墙支撑 buoy tender 航标船buoyant 浮力的 buoyant box 浮箱Bureau Veritas法国船级社CirCUlati On theory 环流理论ClaSSifiCati on SOCiety 船级社cleat 系缆扣CIiPPer bow 飞剪型船首CIUtCh 离合器COaStaI Cargo 沿海客货轮COfferdam 防撞舱壁Comb ined CaSt and rolled Stem 混合型艏柱COmmerCiaI ShiP 营利用船COmmiSSary SPaCeS 补给库舱室，粮食库Com mon Carrier 通用运输船COmmUter 交通船COmPartme nt 舱室COmPaSS 罗经con CePt deSig n 概念设计conn eCt ing tank 连接水柜COnStraintCOn diti on 约束条件COntainer 集装箱COntain erized 集装箱化con tract desig n 合同设计con tra-rotati ng propellers 对转桨con trollable-pitch 可控螺距式corrosio n 锈蚀，腐蚀couple 力矩，力偶Crane 克令吊，起重机Cra nk 曲柄CreSt (of WaVe) 波峰CreW quarters 船员居住舱CriteriO n 判据，准则CritiCaI Path MethOd 关键路径法CrOSS-Cha nnel automobile ferries 横越海峡车客渡轮CrOSS-SeCti onal area 横剖面面积crow ' SneSt 桅杆瞭望台CrUiSer Ster n 巡洋舰尾CrUSS ing range 航程CUP and ball joint 球窝关节CUrVatUre 曲率CUrVeS of form 各船形曲线CUShi on of air 气垫damage StabiIity 破损稳性damper 缓冲器damp ing 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at Side 甲板边线deck Ion gitudi nal 甲板纵骨deck Str in ger 甲板边板deck tran SVerSe 强横梁deckhouse 舱面室，甲板室deep V hull 深V型船体delivery 交船depth 船深derrick 起重机，吊杆desig n margin 设计余量design SPiraI 设计螺旋循环方式destroyer 驱逐舰detachable ShaCkIe 散合式连接卸扣detail desig n 详纟田设计diago nal Stiffe ner 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dime nsionl ess ratio 无量纲比值displaceme nt 排水量displaceme nt type VeSSeI 排水型船distributed load 分布载荷divisio n 站，戈U分，分隔do work 做功dock 泊靠double hook 山字钩double iterati on PrOCedUre 双重迭代法double roller chock 双滚轮式导览钳double-acting Steam cylinder 双向作用的蒸汽气缸dow n halyard 降帆索draft 吃水drag 阻力，拖拽力drain age 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilli ng rig 钻架drillship 钻井船drive Shaft 驱动器轴driv ing gear box 传动齿轮箱driv ing Shaft SyStem 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/ 后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings general arrangement general cargo ship generatrix 母线geometrically similarform外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19 世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016 公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultativ e Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Soci ety (IACS) 国际船级社联合会International Towing T ank Conference (ITTC)国际船模试验水池会议intersection 交点，交叉，横断(切) inventory control 存货管理iterative process 迭代过程装以密封垫的开口总布置杂货船jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier liquid chemical tanker list 倾斜living and utility spacesLloyd 'R s egister of shipping 劳埃德船级社Lloyd 'R s ules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier multi-ship program mushroom ventilator mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）longitudinal （transverse）液体散货船液体化学品船居住与公用舱室多用途船多种船型建造规划蘑菇形通风桶纵（横）稳心高N/C 数值控制nautical mile 海里naval architecture造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩远洋船偏离中心的装载离岸钻井离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft poop 尾楼port 左舷port call 沿途到港停靠positive righting moment power and lighting system precept 技术规则preliminary design pressure coaming principal dimensionsProgram Evaluation and Review Technique 划评估与复核法progressive flooding project 探照灯propeller shaft bracket propeller type log PVC foamed plastic quadrant 舵柄quality assurance quarter 居住区quarter pillar quartering sea quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）ocean going shipoff-center loadingoffsets 型值offshore drillingoffshore structure极地考察船正扶正力矩动力与照明系统初步设计阻力式舱口防水挡板主尺度累进进水尾轴架螺旋桨推进器测程仪PVC 泡沫塑料质量保证舱内侧梁柱尾斜浪racking 倾斜，变形，船体扭转变形 radiography X 射线探伤 rake 倾斜 raked bow前倾式船首raster 光栅 refrigerated cargo ship 冷藏货物运输船 Register （船舶）登录簿，船名录 Registo Italiano Navade意大利船级社regulating knob of fuel pressure 燃油压力调节 钮内底横骨 雷诺数右旋进桨 扶正力臂，恢复力臂 刚性侧壁 riverine warfare vessel rivet 铆接，铆钉 roll 横摇 roll-on/roll-off (Ro/Ro) rotary screw propeller rounded gunwale rounded sheer strake rubber tile 橡皮瓦 rudder 舵 rudder bearing rudder blade rudder control rod rudder gudgeon rudder pintle rudder post rudder spindle rudder stock rudder trunk run去流段 sag 中垂 salvage lifting vessel scale 缩尺，尺度 schedule coordination schedule reviewsscreen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱 sea state 海况 seakeeping 适航性 seasickness 晕船 seaworthness 适航性 seaworthness 适航性 section moulus 剖面模数 sectiongs 剖面，横剖面 self-induced 自身诱导的 self-propulsion 自航 semi-balanced rudder 半平衡舵 semi-submersible drilling rig半潜式钻井架shaft bossing 轴榖 shaft bracket 轴支架 shear 剪切，剪力 shear buckling 剪切性屈曲 shear curve剪力曲线sheer 舷弧 sheer aft 艉舷弧sheer drawing 剖面图 sheer forward 艏舷弧 sheer plane 纵剖面 sheer profile 总剖线 sheer profile 纵剖图 shell plating船壳板ship fitter 船舶装配工 ship hydrodynamics 船舶水动力学 shipway 船台 shipyard 船厂 shrouded screw 有套罩螺旋桨，导管螺旋桨 side frame 舷边肋骨 side keelson 旁内龙骨 side plate 舷侧外板 side stringer 甲板边板single-cylinder engine 单缸引擎 sinkage 升沉 six degrees of freedom 六自由度skin friction表面摩擦力skirt (气垫船)围裙 slamming 砰击 sleeve 套管，套筒，套环 slewing hydraulic motor 回转液压马达储备浮力 剩余阻力reserve buoyancy residuary resistance resultant 合力 reverse frame Reynolds number right-handed propellerrighting arm rigid side walls rise of floor 底升内河舰艇滚装回转式螺旋推进器 修圆的舷边圆弧舷板救捞船生产规程协调 施工生产进度审核舵承 舵叶操舵杆 舵钮舵销 舵柱舵轴 舵杆 舵杆围井slice 一部分，薄片 sloping shipway有坡度船台sloping top plate of bottom side tank 斜顶板slopint bottom plate of topside tank 底板Suez Canal tonnage底 边 舱 superintendent superstructure 定边舱 斜Supervision ofthe验船师的监造书苏伊士运河吨位限制 监督管理人，总段长，车间主任 上层建筑Society 's s urveyor 船 级社supper cavitating propeller 超空泡螺旋桨 surface nozzle 水面式喷口 surface piercing 穿透水面的 surface preparation and coating 表面加工处理 与喷涂surge 纵荡 surmount 顶上覆盖，越过 swage plate 压筋板 swash bulkhead止荡舱壁SWATH (Small Waterplane Area Twin Hull)小水线面双体船steering gear 操纵装置，舵机 stem 船艏 stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒 stern counter 尾突体 stern ramp 尾滑道，尾跳板 stern transom plate 尾封板 stern wave 艉波 stiffen 加劲，加强 stiffener 扶强材，加劲杆 straddle 跨立，外包式叶片 strain 应变 strake 船体列板 streamline 流线 streamlined casing 流线型套管 strength curves 强度曲线 strength deck强力甲板stress concentration 应力集中 structural instability结构不稳定性strut 支柱，支撑构型 subassembly 分部装配 subdivision 分舱 submerged nozzle 浸没式喷口 submersible 潜期 tail-stabilizer anchor 尾翼式锚talking paper讨论文件tangential 切向的，正切的 tangential viscous force 切向粘性力 tanker 油船 tee T 型构件，三通管 tender 交通小艇 tensile stress 拉(张)应力thermal effect 热效应 throttle valve 节流阀 throughput 物料流量 thrust 推力 thruster 推力器，助推器 timber carrier 木材运输船 tip of a blade 桨叶叶梢tip vortex梢涡toed towards amidships 趾部朝向船舯 tonnage 吨位 torpedo 鱼雷 torque 扭矩 torque 扭矩 trailing edge 随边 transom stern 方尾suction back of a blade桨叶片抽吸叶背transverse bulkhead plating 横隔舱壁板summer load water line夏季载重水线soft chine 圆舭 sonar 声纳 spade rudder 悬挂舵 spectacle frame 眼睛型骨架 speed-to-length ratio 速长比 sponson deck 舷伸甲板 springing 颤振 stability 稳性 stable equilibrium稳定平衡starboard 右舷 static equilibrium 静平衡steamer 汽轮船sway 横荡船舶专业英语词汇（按照字母顺序排列） （七）transverse section 横剖面 web frame 腹肋板 transverse stability横稳性weler 焊工trawling 拖网wetted surface 湿表面积 trial 实船试验winch 绞车trim 纵倾windlass 起锚机 trim by the stern/bow 艉艏倾wing shaft 侧轴trimaran 三体的wing-keel 翅龙骨（游艇）tripping bracket 防倾肘板working allowance 有效使用修正量 trough 波谷 worm gear 蜗轮，蜗杆 tugboat 拖船yacht 快艇tumble home ( 船侧）内倾yard issue 船厂开工任务发布书 tunnel wall effect 水桶壁面效应 yards 帆桁 turnable blade可转动式桨叶yaw 首摇turnable shrouded screw 转动导管螺旋桨 tweendeck cargo space 甲板间舱 tweendedk frame 甲板间肋骨 two nodded frequency 双节点频率ULCC 超级大型原油轮 ultrasonic 超声波的 ventilation and air conditioning diagram 与空调铺设设计图Venturi section 文丘里试验段 vertical prismatic coefficient vertical-axis(cycloidal)propeller 进器横剖面系数 直叶 （摆线） 推vessel component vender 造船部件销售商viscosity 粘性 VLCC 巨型原油轮 Voith-Schneider propeller外摆线直翼式推进器 v-section v 型剖面 wake current 伴流，尾流 water jet 喷水(推进)管 water plane 水线面 watertight integrity 水密完整性 wave pattern 波形 wave suppressor 消波器，消波板 wave-making resistance 兴波阻力weather deck 露天甲板 web 腹板 web beam 强横梁underwriter unsymmetrical upright position vapor pocket海运）保险商 非对称的 正浮位置 气化阱通风。
船舶专业英语词汇
ABS (American Bureau of Standard)美国船级社ANG (Angle Bar)角钢BFE (Builder Furnish Equipment)建造商提供设备BG (Bulk Carrier)散货船BHD (Bulkhead)舱壁BHP (Break Horsepower)制动马力BL (Base Line)基线BM (Breadth Molded)型宽BV (Bureau Veritas)法国船级社CAD (Computer Aided Design)计算机辅助设计CAM (Computer Aided Manufacturing)计算机辅助制造CB (Center of Buoyancy)浮心CCS (China Classification Society)中国船级社CF (Center of Floatation)漂心CFE (Contractor Furnish Equipment)承包商提供设备CG (Center of Gravity)重心CH (Channel)槽钢CM (Metacenter)稳心CPP (The Controllable Pitch Propeller)可调螺距桨CS (Carbon Steel)碳素钢DB (Double Bottom)双层底DK (Deck)甲板DM (Depth Molded)型深DNV (Det Norske Veritas)挪威船级社DWG (Drawing)图DWL (Design Waterline)设计水线DWT (Deadweight)载重量FAT (Factory Acceptance Test)工厂验收试验FB (Flat Bar)扁钢FEM (Finite Element Method)有限元法FPSO (Floating Production Storage Offloading) 浮（船）式生产储油卸油系统FSO (Floating Storage Offloading)浮（船）式储油卸油系统Fwd (Forward)向船艏GL (Germanischer Lloyd)德国船级社GM (Metacentric Height)初稳心高HP (Half Bulb Plate)球扁钢LBP (Length between Perpendiculars)垂线间长LCG (Longitudinal Center of Gravity)纵向重心LNG (Liquefied Natural Gas Vessel) 液化石油气船LOA (Overall Length)总长Long. (Longitudinal)纵骨LPG (Liquefied Petroleum Gas Vessel) 液化天然气船LR (Lloyd's Register)英国劳氏船级社MDK (Main Deck)主甲板MODU (Mobile Offshore Drilling Units)移动式近海钻井平台MS (Mild Steel)低碳钢MTO (Material Takeoff)材料估算NK (Nippon Kaiji Kyokai)日本海事协会OFE (Owner Furnished Equipment)船东提供设备OT (Oil Tight)油密PL (Plate)板RI (Register Italian)意大利船级社SB (Starboard)右舷Semi- (Semi-submersible Platform)半潜式钻井平台STLP (Suspended Tension Leg Platform)悬式张力腿平台TCG (Transverse Center of Gravity)横向重心TEU (Twenty-foot equivalent Unit)20英尺国际标准集装箱TLP (Tension Leg Platform)张力腿平台UCLL (Ultra Large Crude Carrier)超大型油船VCG (Vertical Center of Gravity)垂向重心VLCC (Very Large Crude Carrier)特大型油船WB (Web Bar)腹板WL (Waterline)水线WT (Water Tight)水密MECHANICAL & PIPING（轮机）：AHU (Air Handling Unit)通风装置BHP (Break Horsepower)制动马力A/C (Air Compressor)空气压缩机A/C (Air Conditioning)空调BB (Ball Bearing)滚珠轴承BRG (Bearing)轴承CAS NUT(Castle Nut)蝶型螺帽CCR (Central Control Room)中心控制室COW (Crude Oil Washing)原油洗舱DFO (Diesel Fuel Oil)柴油DPS (Dynamic Position System)动力定位系统DT (Double-Thread)双头螺纹FS (Forged Steel)锻钢FW (Fresh Water)淡水FO (Fuel Oil)燃油GRP (Glass-reinforced Plastic)玻璃钢HVAV (Heating Ventilation and Air-condition)暖通空调系统HPU (Hydraulic Power Unit)液压工作站LSA (Life Saving Apparatus)救生器具LCC (Local Control Console)机旁控制台LO (Lube Oil)滑油MDO (Marine Diesel Oil)船用柴油OS (Operation System)操作系统PLC (Programmable Logic Controller)逻辑控制单元PMS (Power Manage System)动力管理系统ELECTRICAL（电气）:AC (Alternative Current)交流电AVR (Automatic Voltage Regulation)自动电压调整计CCTV (Closed Circuit Television)闭路电视CMS (Cargo Monitoring System)货物监控系统DC (Direct Current)直流电DFT (Dry Film Thickness)干膜DG (Diesel Generator)柴油发电机DVD (Digital Video Disc) 数字化视频光盘EMSP (Emergency Shutter Panel)应急关断板ESS (Emergence Shutdown System)应急关闭系统GPS (Global Position System)全球定位系统HG (Harbor Generator)停泊发电机HT (High Temperature)高温JB (Junction Box)接线盒LED (Light Emitting Diode)发光二极管LT (Low Temperature)低温MCU (Main Control Unit)主控器箱MG (Main Generator)主发电机MUR (Manual Voltage Regulation)手动调压器NEMA (National Electrical Manufacturers Association)国际电气制造业协会PA (Public Address System)公共寻呼系统PWM (Pulse Width Modulation)脉宽调制ST (Starter)启动器SWBD (Switch Board)配电盘，配电板UPS (Uninterrupted Power Supply)不间断电源VCR (Video Cassette Recorder)录像机PAINTING（涂装）:ARD (Alkyd Resin Deck)醇酸树脂甲板漆ARF (Alkyd Resin Finish)醇酸树脂面漆ARP (Alkyd Resin Primer)醇酸树脂底漆A/C (Anti-corrosive Paint)防腐漆CAF (Compressed Asbestos Fiber)压缩石棉填料EDP (Epoxy Deck Paint)环氧甲板漆EFP (Epoxy Finish Paint)环氧面漆EPP (Epoxy Primer Paint)环氧底漆ETPF (Epoxy Tank Paint Finish)环氧舱室面漆ETPP (Epoxy Tank Paint Primer)环氧舱室底漆ETP (Epoxy Topside Paint)环氧干舷漆ERL (Erosion Resistant Lacquer)防腐漆ECP (Etching Primer) 磷化底漆EPR (Ethylene-Propylene Rubber)乙丙橡胶F/C (Finish Coating)面漆IZP (Inorganic Zinc Primer)无机锌底漆IZSP (Inorganic Zinc Shop Primer)无机锌车间底漆UTP (Polyurethane Topside Primer)聚氨脂干舷漆TE (Tar Epoxy Paint)环氧焦油漆VTP (Vinyl Tar Primer)聚乙烯焦油底漆ZRP (Zinc Rich Primer)富锌底漆WELDING and Material（焊接与材料）ASTM (American Society for Testing Materials)美国材料实验协会AWS (American Welding Society)美国焊接协会FCAW (Flux Cored Arc Welding)药芯焊丝电弧焊FRP (Fiberglass Reinforced Polyester)玻璃钢GMAW (Gas Metal Arc Welding)气体保护金属极电弧焊GRP (Glass Reinforced Polyester)玻璃钢GTAW (Gas Tungsten Arc Welding)气体保护钨极电弧焊GW (Gravity Welding)重力焊MPI (Magnetic Particle Inspection) 磁粒检验NDE (Nondestructive Evaluation)无损鉴定NDT (Nondestructive Testing)非破坏性检验PVC (Poly Vinyl Chloride)聚氯乙烯S/W (Spot Weld) 点焊SAW (Submerge Arc Welding)埋弧焊SMAW (Shielded Metal Arc Welding)手弧焊UT (Ultrasonic Test)超声波检验WPS (Welding Procedure Sheet)焊接程序表WQT (Welding Qualification Test)焊工资格检验OTHERS（其它）AE (Assistant Engineer)助理工程师ANSI (American National Standards Institute)美国国家标准局API (American Petroleum Institute)美国石油协会ASME (American Society of Mechanical Engineers)美国机械工程师协会Bbls (Barrels) 桶（美制容量单位1桶= 159升），C.E. (Chief Engineer) 总工程师CEO (Chief Executive Officer)首席执行总裁CIS (Chinese Industrial Standard)中国工业标准CNOOC (China National Offshore Oil Company)中国海洋石油总公司Co Ltd.(Company Limited)（股份）有限公司cu.ft. (Cubic Feet) 立方英尺cu.in. (Cubic Inch) 立方英寸GB (Guo Biao)国标GM (General Manage)总经理H.Q. (Headquarters) 总部HSE (Health, Safety & Environment)健康，安全和环保ID (Inner Dimension)内径IEC (International Electro technical Commission)国际电工协会IMO (Intergovernmental Marine Organization)国际海事组织ISO (International Standardization Organization)国际标准化协会ITU (International Telecommunication Union)国际电信联盟Ksi (kilopounds per square inch)千磅/平方英寸N/A (None Applicable)不适用NACE (National Association of Corrosion Engineer)全国防蚀工程师协会NFPA (National Fire Protection Association)国家防火协会OD (outer Dimension)外径QA (Quality Assurance)质量保证QC (Quality Control)质量管理（检查）ST (Short Ton)短吨SOLAS (International Convention of the Safety of Life at Sea)国际海上人命安全公约Spec. (specification)说明书，规格书sq.ft. (Square Feet) 平方英尺sq.in. (Square Inch) 平方英寸PROPER NOUN（专有名词）:Basic Design(基础设计): Preparation of specification and plans/drawings outlining the design and in sufficient detail to gain Class approval.总括性的设计规格书和图纸等，其详细程度仅足可以通过船级社认可其设计思想。
船舶专业英文词汇
船舶专业英文词汇
CAE(computer-aided manufacturing) 计算机辅助制造 CAM(computer-aided engineering) 计算机辅助工程 camber 梁拱 cant beam 斜横梁 cant frame 斜肋骨 cantilever beam 悬臂梁 capacity plan 舱容图 CAPP(computer –aided process planning) 计算机辅助施工计划制定 capsize 倾覆 capsizing moment 倾覆力臂 captain 船长 captured-air-bubble vehicle 束缚气泡减阻船 cargo cubic 货舱舱容，载货容积 cargo handling 货物装卸 carriage 拖车，拖架 cast steel stem post 铸钢艏柱 catamaran 高速双体船 catamaran 双体的 cavitation 空泡 cavitation number 空泡数 cavitation tunnel 空泡水筒 center keelson 中内龙骨 centerline bulkhead 中纵舱壁 centroid 型心，重心，质心，矩心 chain cable stopper 制链器 chart 海图 charterer 租船人 chief engineer 轮机长 chine 舭，舷，脊 chock 导览钳 CIM(computer integrated manufacturing) 计算机集成组合制造
/ShowPost.asp?ThreadID=519（第 1／31 页）2007-2-5 20:33:21
船舶专业英语词汇
船舶专业英语词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线学习资料basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱学习资料Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀学习资料couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）学习资料e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架学习资料freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒学习资料hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organ ization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IA CS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船学习资料liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽学习资料notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证学习资料quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力学习资料shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期学习资料suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置学习资料vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板weler 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇学习资料。
船舶英语词汇
船舶英语词汇船舶英语词汇汇总船舶专业主要培养具备现代船舶与海洋工程设计、研究、建造的基本技能和管理基础知识、计算机编程及应用能力，能在船舶与海洋结构物设计、研究、制造、检验、使用和管理等部门从事技术和管理方面工作的船舶与海洋工程学科高级工程技术人员。
下面店铺为大家推荐一些关于船舶专业的英语词汇，希望对大家的学习有所帮助。
祝纳汽阀图 Zeuner valve diagram零位线 zero line交错铆 zigzag riveting交错铆接 zigzag riveting锌铬黄(漆) zinc chromate锌板 zinc plate保护用]锌板 zinc protector[锌块 zinc slab零值中心安培计 zero center ammeterZ形推进系 Z-peller交错固结 zigzag fastening镀锌 zincing含锌漆 zincrich paint荧光探伤法 zyglo inspection method硅氟化锌 zinc fluosilicate区域?装 zone outfitting零位线 zero line零相电流 zero phase sequence current无推力节距(螺桨) zero thrust pitch锌 zinc锌池 zinc bath零弯矩跨距 zero moment span荧光渗透探伤法 zyglo penetrant method 镀锌 zinc galvanizing (or plating)区域 zone无扭矩节距(螺桨) zero torque pitchZ形材 Z bar曲折接法 zigzag connection交错间断焊接 zigzag intermittent weld 零相[序] zero phase sequence祝纳氏汽阀图 Zeuner valve diagram曲折操纵,Z形操纵 zigzag maneuvering 零升力攻角 zero-lift angle交错焊接 zigzag weld。
船舶专业英语词汇
Principal dimension主尺度Aspect外表样子Perpendicular垂线Keel plate龙骨板Draught/draft吃水Freeboard干舷Horizontal 水平的Stern船尾，尾柱Frame框架，肋骨Trim纵倾Depth型深Sheer舷弧Camber梁拱Drainage排水Resistance阻力Stability稳性Maneuverability操纵性Longitudinal纵向的The front of the stem首柱Port side左舷Vertical distance垂直距离Water line设计水线Initial stability初稳性Gross tonnage总吨位Net tonnage净吨位Crew船员Compartment分隔舱Spaces 舱室Volume/capacity舱容Navigation航海Propulsion推进propeller螺旋桨Anchor锚rudder舵Appliance设备Container vessel集装箱船Roll-on and roll-off滚装船Passenger ship客船Port dues港口费Dimensionless number无因次数Daily expenses日常开支Ship owner船东Workship工作间Displacement排水体积Ordinate纵坐标，站Projection投影Cattle ships运畜船Tier层Bilge船底/舭部Lash扎；捆Bollard系船柱Pull拖力Hatch舱口hatchcover舱口盖ISO/IMOTEU/FEU箱位Cargo gear/loading gear起货装置Harbour/port港口Tanker capacity吞吐量Tweendeck双层甲板Headledge首支架Coaming围板Discharging/unloading卸货Bulwark舷墙Crane起重机Ballast压载Wheelhouse驾驶室Mast桅杆Deadweight（DWT）载重量Carring capacity装载能力Bilge keel舭龙骨Liquefy液化liquefied液化的Leak泄露Turbine涡轮stem turbine蒸汽机Slep tank污油舱Cancel运河Freezing point冰点Liquid state液态Free liquid surface自由液面Tank wall鑵壁Toil-off蒸发气Crude oil tanker原油船Product oil tanker成品油船Double hall双层壳Ventilation通风Flammability 易燃性Cofferdam隔离舱Fore peak/aft peak首尖舱/尾尖舱Sounding apparatus声纳仪Bottom底部Stiffen加强stiffener加强筋Hull construction船体结构Upper deck上层甲板lower deck下层甲板Compass deck罗经甲板Navigation deck驾驶甲板Boat deck艇甲板；救生甲板Accommodation deck起居甲板Transversal bulkhead横舱壁Bow section船首段Midship section船中段Stern section船尾段Main hull主船体Transversely system of farming横骨架式Longitudinal system of framing纵骨架式Floor plate肋板Shell plating船壳板Shell structure外板结构Total longitudinal bend总纵弯曲Wave impact波浪冲击Bottom plate船底板Keel plate龙骨板Bilge plate舭板Side plate舷侧板Top side plate舷顶列板Wing tank边舱Stringer桁材Girder纵桁cofferdam隔离舱beam横梁hatch trunk舱口围板pillar支柱stiffener扶强材，加强筋bottom structure底部结构side structure舷侧结构deck structure甲板结构bulkhead structure舱壁结构bow structure首结构stern structure尾结构single bottom单底double bottom双底longitudinal member纵向构件transversal member横向构件inner bottom longitudinal内底纵骨inner bottom plate /tank top plate内底板deck plate甲板板deck girder甲板横梁longitudinal bulkhead纵舱壁transverse bulkhead横舱壁anchor winch起锚机forecastle前甲板，首楼poop deck艉楼mooring停泊bulb stem球鼻首main engine shaft/propeller shaft主机轴/螺旋桨轴collision bulkhead防撞舱壁wash bulkhead制荡舱壁chain locker锚链舱unloaded ship空载船bunker tank燃料舱engine foundation机座floatability浮性roll横摇pitch纵摇heel横倾trim纵倾Floodability抗沉性stability稳性metacentre稳心consumption消耗fast speed （rapidity）快速性gravity center重心transversal stability横稳性inclination test倾斜试验friction resistance摩擦阻力swirl resistance涡流阻力wave-forming resistance兴波阻力upset倾覆seasick晕船stabilizer减摇鳍course航向the propulsion plant推进装置basic design基本设计the roll period横摇周期stabilizing unit减摇装置bilge keel舭龙骨wing buoyant tank减摇水舱sea damage海损directional stability航向稳定性turning ability回转性。
船舶专业英语词汇(按英文字母排序)
船舶专业英语词汇（按英文字母排序）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的-anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪aanchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍爱antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢-bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经-concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流_flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱船forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位爱我船舶网in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇船launching equipmeng （向水中）投放设备leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性_seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位Ptorpedo 鱼雷trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷爱我船舶网tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮V oith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web beam 强横梁web frame 腹肋板weler 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。
船舶专业英语词汇
船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船尾[adv][prep]abandonment cost 船舶废置成本费用accommodation 居住（舱室）living quarter accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯[adv]amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板Beacon 灯塔，示位标bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth molded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定、公约船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer租船人charterchief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室，间隔舱compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船throughoutdistributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠vtdouble hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水，草图，设计图drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak tank 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forgeforward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修furniture gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse)纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性section moulus 剖面模数sections 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机bow 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮very large crude carrierVoith-Schneider propeller/ propulsion外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity/integrality 水密完整性integrate 整合completeness wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工melterwetted surface 湿表面积winch 绞车mooring winchwindlass 起锚机anchor windlasswing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇二．轮机1． Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).螺旋桨轴（中间轴）机加工尺寸检查。
船舶专业英语 词汇
vi. 一致；记分
7, changing ['tʃeindʒiŋ]
v. 改变（change的ing形式）；交换；兑换
n. 改变；转换；替换
adj. 变化的；发展的
8, gym [dʒim]
n. 健身房；体育；体育馆
9, electric [i'lektrik]
n. 阀门；瓣膜（valve的复数）；真空管
v. 装阀于…；以活门调节（valve的三单形式）
72, gas freeing
73, undertaken
v. 从事；开始进行（undertake的过去分词）
74, outer hull
outer hull: 外壳 | 外部壳体
66, occupied ['ɔkjupaid]
adj. 已占用的；使用中的；无空闲的
v. 占有（occupy的过去分词）
67, emergency [i'mə:dʒənsi]
n. 紧急情况；突发事件；非常时刻
adj. 紧急的；备用的
68, escape [i'skeip]
vt. 逃避，避免；被忘掉
adj. 老练的，熟练的；富有经验的
93, bulwark ['bulwək]
n. 壁垒；保障；防波堤
vt. 保护；筑垒保卫
94, freeing port
放水闸；排水口；甲板排水孔
95, funnel ['fʌnl]
n. 漏斗；烟囱
vt. 通过漏斗或烟囱等；使成漏斗形
vi. 通过漏斗等；成漏斗形
总布置
船舶专业英语词汇表
2006-8-11 16:321、1结构 Structure船厂 dockyard/shipyard 船坞 dock/boatyard船东 ship-owner 船舷 Ship's side船舱 hold 甲板 Deck船籍 Ship's registry 住舱甲板 accommodation deck 船首 bow 梁拱甲板 arch deck船尾 stern 首楼甲板 Forecastle deck2船坞 dock/boatyard船舷 Ship's side船的栏杆 Ship's rail甲板Deckeck梁拱甲板 arch deck载货甲板 cargo deck首楼甲板 Forecastle deck上甲板 Upper deck下甲板 Lower deck货舱甲板 Hold deck桥楼甲板 Bridge deck水密甲板 Watertight deck3艇甲板 Boat deck罗经甲板 Compass deck板 Plate舭板 Bilge plate船首外板 Bow plate肘板 Bracket plate舱壁板 Bulkhead plate槽形舱壁板 Corrugated bulkhead plate铜-钢复合板 Copper sheathing steel plate 甲板边板 Deck stringer plate斜板 Sloping plate加强板 Reinforcement plate平台 platform机舱平台 Engine-room platform分段 Block首段 Bow block中段 Midship block5尾段 Stern block左舷 port右舷 Starboard甲板纵桁 Deck girder横桁 Cross girder水平桁 Horizontal girder舱口边梁 Hatch coaming girder机座纵桁 Engine girder6甲板下纵桁 Underdeck girderframe船底肋骨 Bottom frame首肋骨 Bow frame肘板框架肋骨 Bracket frame球鼻首肋骨 Bulbous bow frame球曲型肋骨 Bulbous frame主肋骨 Chief frame首肋骨 Fore frame7桁架梁 me 甲板纵桁 Deck longitudinal横框架肋骨 Transverse frame 内底纵桁/纵骨 Inner bottom longitudinal肋距 F.S.(frame space) 舷侧纵桁/纵骨 Shell side longitudinal纵桁/纵骨/纵向构件 longitudinal 双层底顶纵骨 Top longitudinal of doublebottom8斜舱壁纵骨 Slopping-bulkhead longitudinal 舱 Tank结构 Structure 尾尖舱 after peak tank附属结构 Accessory structure 尾部水舱 after water tank全焊结构 All-welded structure 辅助水柜 Auxiliary water tank structure 底舱 Bottom tank船首部结构 Bow structure 底边舱 Bottom side tank支撑结构 Braced structure 货油压载舱 Cargo and ballast tank桥楼结构 Bridge structure 循环水槽 Circulating flow water tank首楼结构 Foreca人孔 manhole 干舱 Dry tank9舱 Tank尾尖舱 after peak tank尾部水舱 after water tank辅助水柜 Auxiliary water tank辅助压载水舱 Auxiliary water ballast tank污and ballast tank循环水槽 Circulating flow water tank循环滑油舱 Circulating lubricating oil tank构架结构 Framed structure纵桁结构 Girder structure人孔 manhole10k应急淡水柜 Emergency fresh water tank首舱 Fore tank首尖舱 Fore peak tank斜边舱 Hopper side tank液舱 Liquid tank龙骨舱 Keel tank右舷舱 Starboard tank顶边水舱 Topside tank顶边翼舱 Topside wing tank小舱口盖 Small hatch cover水密舱口盖 Water-tight small hatch cover风雨密舱口盖 Weather-tight small hatch cover页面功能【字体：大中小】【打印】【关闭】dugout独木舟barge驳船kayak（爱斯基摩人的）木排outrigger桨叉架船rowing boat划艇（美作：rowboat）gondola（意大利的）长平底船whale mother ship捕鲸母船hydrofoil水翼船catamarans双体船dredger挖泥船boat船brig， brigantine双桅船canoe小船，独木舟caravel快帆船cargo boat货船coaster近海贸易货船cod-fishing boat捕鳕鱼船whaler捕鲸船collier运煤船battleship战船shallop小型战船coastguard cutter， coastguard vessel巡逻艇，缉私艇revenue cutter缉私船patrol boat巡逻艇minelayer布雷艇minesweeper扫雷艇torpedo boat鱼雷艇frigate轻护航舰gunboat炮舰submarine潜水艇destroyer驱逐舰corvette轻巡洋舰cruiser巡洋舰aircraft carrier航空母舰ferry， ferryboat渡船，渡轮fishing boat渔船freighter货船galleon大型帆船galley大划桨船hovercraft气垫船icebreaker破冰船launch艇lifeboat救生艇lighter驳船liner， ocean liner远洋班轮merchant ship， merchantman商船motorboat摩托艇outboard尾部装有马达的小艇paddle steamer， paddle boat明轮船passenger boat客船piragua， pirogue独木舟raft木筏rowing boat划艇sailing boat， sailing ship帆船schooner纵帆船ship船skiff小艇sloop单桅船steamer， steamship汽轮tanker油轮trawler拖网渔船tug， tugboat拖轮vessel船yacht游艇yawl船载小艇船舶英语自动雷达标绘仪Automatic radar plotting aid 自动电话Automatic telephone电压自动调节器Automatic voltage regulator 自动化系统Automation system压载控制台Ballast control console镇流器Ballast底座Base电池Battery铃Bell弯曲Bend床头灯Berth light失电Black out刹车Brake电刷Brush船舶英语3球鼻首警告灯Bulbous bow warning light 汇流排Bus(-)bar汇流排Bus –tie –in蜂鸣器BuzzerC、电缆Cable电缆填料函Cable gland敷设电缆Cable laying电缆管Cable pipe (conduit)电缆扎带Cable strap电缆托架Cable tray校准器Calibrator电容capacitor阴板Cathode警告牌Caution plate船舶英语4顶灯Ceiling light中央处理器Central processing unit通道Channel充电器Charger充放电板Charging&discharging board 海图灯Chart table light检查Check芯片Chip清洁Clean雨雪清除器Clear view screen二氧化碳释放报警CO2 release alarm 同轴电缆Coaxial cable线圈Coil冷库呼叫Cold store calling船舶英语5通讯Communication计算机Computer接头Connector恒电流Constant current消耗Consumption触头Contact接触器Contactor控制箱Control box控制箱Controller芯线Core角灯Corner light计算器Counter电流CurrentD、损坏Damage船舶英语6危险气体报警箱Dangerous gas detecting &alarm box 白昼信号灯Daylight signal light去耦Decoupling set台灯Desk light控测器Detector拨号Dial数字选择呼叫收信机Digital select –call receiver调光器dimmer直流电Direct current直接起动Direct –on –line starting磁盘Disk显示Display遇险信息控制器Distress message controller多普勒记程仪Doppler speed log船舶英语7双极单刀开关Double pole single way switch双极双刀开关Double pole two way switch天线收发转换开关Duplexer值班水手呼叫Duty sailor calling接地Earth接地排Earth bar测深仪Echo sounder电工试验板Electric test panel电机员Electrical engineer电极Electrode应急照明分电箱Emergence lighting distribution box应急示位标Emergence position indicating radio beacon 应急停Emergence stop船舶英语8应急配电板Emergency switch board机舱报警Engine alarm集控台Engine control console机舱监测报警Engine room monitoring &alarm system 轮机员呼叫Engineer calling panel轮机员安全Engineer safety system增强群呼叫收讯机Enhance group call receiver交换机Exchanger防爆灯Explosion proof light延伸报警板Extension alarm panel故障Failure故障Fault反馈Feed back船舶英语9馈电品Feeder panel滤波器Filter火警复显器Fire alarm repeater防火风闸控制单元Fire damper control unit火警检测箱Fire detecting box火焰探头Flame detector闪光灯Flash light浮充电Float charge强光灯Flood light流程图Flow chart流量开关Flow switch荧光灯Fluorescent light雾笛Fog horn频率Frequency船舶英语10熔丝Fuse填料Gasket通用报警General alarm发电机Generator发电机屏Generator panel（铜）锣、钟Gong全球卫星定位导航GPS navigator 组合灯板Group alarm light pillar 组合起动屏Group starter panel 电罗经Gyro compass卤素灯Halogen light听筒Handset硬件Hardware航向Headingcontinue很好，支持一下！汇流排Bus –tie –in 最好有图片Double pole single way switchvery usefull.very usefull.study itwhy do not you send in one note?very usefull.study it general alarm.通用报警very usefull.study Filter=滤波器and flow chart=流程图交换机=Exchanger ,studywhat is word to describe the ”显示器“？use display or not？页: [1] 2船舶英语手册10请给我看一下电站负荷平衡表。
船舶专业英语词汇
1．基本，简单的词汇：AM 上午 PM下午Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书；a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师2、船体总体，及各类型船舶Hull 船体Forecastle 艏楼Stern 船尾Poop 艉楼Superstructure 上层建筑Foremast 前桅杆After mast 后桅杆Radar mast 雷达桅杆Main deck 主甲板Upper deck 上甲板Poop deck 艉楼甲板Accommodation deck 生活甲板Compass deck 罗经甲板Funnel 烟囱Bridge 桥楼，驾驶台Bridge wing 驾驶室翼桥Wheel house 驾驶室Engine room 机舱Engine control room 机舱集控室Catwalk 天桥、步桥Flying bridge （露天）航行驾驶室Rescue boat 救助艇Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船Naval Ship/war shipd 军船Ice-breaker 破冰船Container vessel 集装箱船Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架Chemical carrier 化学品运输船Liquefied gas carrier 液化气体船Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇Canoe 独木船，皮舟Junk 平底中国帆船、舳板Gondola （意大利威尼斯的）一种狭长的平底船Yacht 快艇、游艇Fast boat 快艇Patrol boat 巡逻艇Anti-smuggling boat 缉私艇Torpedo boat 公安艇Ferry 渡船Catamaran 双体船Jet foil 喷水水翼艇Wing assrsted vessel 地效船3、各专业基本词汇1）船体：Draft forward 前吃水Draft middle 中吃水Draft after 后吃水Plimsoll mark/lineWaterline 吃水线Waterlines （型）水线Port 左舷Starboard 右舷Sagging 中垂、下垂、下挂（流）Hogging 中拱、上拱Derformation 变形Fairing 光顺、火工校正Hot work热工、明火作业section 分段、部分、剖面Block 分段Keel （船舶）龙骨Bilge keel 舭龙骨Power tool 带动力工具（风动或电动）Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊D.C welding 直流（电弧）焊Grinding 打磨Welding 电焊Spatters 飞溅（电焊）Under out 咬口Sharp edge 快口Deflection 挠曲，变形Slags 渣Welding slags 电焊渣Automatic welding 自动焊Manual welding 手工焊Arc welding 电弧焊Gas shielded welding气体保护焊Inter gas arc welding惰性气体保护电弧焊Welding seam焊缝Bending machine 弯曲机Three-roll bending machine三芯弯板机Torsional box抗扭箱Void space空舱Cofferdam 隔离舱Bulwark舷墙，防浪板Wall墙壁Floor地板Controllable pitch 可调桨Elastic coupling 弹性联轴节Bellow 波纹管Joint接头Gaskets垫片Fitting bolts 拂螺拴Chock 制动块、导缆器Chock fast 环氧垫块Foundation 底座、基座Mounting 装置、座、架Mount （常指火炮等武器的）座，架Vent pipe 透气管Sounding pipe探测管Vapour return line油气回路管Stripping line扫舱管Safety equipment 安全设备Life-saving equipment救生设备Cargo hold 货舱Cargo oil tank货油舱Cabin 船舱、舱室Room房间Store room储藏室Cold room冷库Fish room鱼库Meat room 肉库Provision room粮库Foam room 泡沫库CO2 room二氧化碳室Pump room泵室Battery room蓄电池室Radio room 报务室Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统Sea water piping system 海水管系Water jacket水套Insulation materials绝缘材料Lagging绝缘材料、外套（锅炉、管子等）3）电器Current电流Voltage电压Frequency频率Contact触点、触头Ballast镇流器Convertor变频器、换能器Conductor导体Semi-conductor半导体Rectifier整流器Transformer变压器Thermostat 恒温器Thermister热敏器Edison base 螺丝灯座、爱迪生灯座Bayonet base卡口灯座On-off开关（量）Analogue模拟，模拟设备Active analogue有源模拟、主动模拟Passive analogue无源模拟、被动模拟Dry contact无源模拟、干接触Buzzer蜂鸣器Button按扭，电扭Switch开关Main switch主开关Main switch board主配电板Cable 电缆Wire 电线Three-core cable三蕊电缆Clamp夹钳、夹具Clip 接线柱、线夹Alligator clip鳄鱼夹、弹簧夹Voltage drop 电压降Speed droop速度降低Black out 黑灯试验Power failure失电Setting point 设定点Adjust 调正（v）Adjustment调正（n）Oscillator振荡器、振动器Oscilloprobe示波器测试头Oscilloscope示波器、示波仪Resistor电阻、电阻器Potentiometer电位器、电势计Electrolysis电解（作用）Electrolyte电解质、电解液setting point of power surplus负载余量设定值重载询问test the power surplus setting point重载询问试验4）漆、木Surface preparation表面处理（清理工作）Blasting equipment喷漆（砂粒）装置Sand blasting 喷砂除锈Pre-blasting预喷砂Lingt blasting 预喷砂Full blasting 通喷砂Sand sweep扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting通喷砂后钢结构检查Cleanliness inspection清洁度检查Inspection after degreasing除去油脂后检查Removing oil stains by detergent/solvent使用洗洁剂/容剂除去油迹Shop primer 车间底漆Spray painting喷漆、喷涂法Touch-up 补漆、修正Touch-up painting补漆、点漆First coat 底漆、头道漆Finish coat 面漆Surface coat 表面涂层Under coat 内涂层Wearing coat 磨耗层Zinc-rich coating富锌涂层Cement wash coating（薄）水泥涂层Stripe coating 预涂层Floor covering 地板覆层Alkyd resin paint醇酸树脂漆Epoxy(resin-based)paint环氧树脂涂料Scuttle舷窗Carpet地毯Wooden skirt木裙板（踢脚）Aluminum skirt稆质裙板（踢脚）Brass nose装于楼梯踏步一的黄铜防滑镶条Stainless screw不锈钢螺钉Spring 弹簧Securing dev ice固定件Locking device闭锁装置，制动设备Plywood胶合板，层压板Laminated plate迭层板Laminate层压制品，迭层板，层压板High pressure washing of the hull用高压水冲洗船壳Steel plate temperature 钢板温度Condensation冷凝Capillary condensation毛细管现象Dew point露点Flashing point闪点Ignition point 燃点，着火点Ventilation for coating 涂装通风Dehumidifier去湿机，干燥机Dehumidification 去湿，去潮Sagging流挂，下垂Chalking粉化Peeling剥落（指油漆）Pinhole针孔CureCuring硬化，熟化，硫化Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature硬化、固化温度Power tools有动力的工具（包括电动及风动）Pheomatic tools风动工具Burnt area烧坏的区域Oil stains油迹Scratches划痕Damaged places遭损坏的部位Chicken wire钢丝网Tiles瓷砖，瓦Mosaic-tile彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue胶，粘结剂Silica硅石，二氧化碳Silicagel硅胶Decoration装饰，装修Interior decoration内部装饰，内装Deck head 天花板Ceiling天花板Paneling板墙，镶板Wall墙壁Desk书桌，桌台Drawer 抽屉Catch hook固定钩子Observation window 观察窗Inspection window检查孔窗Clear view window旋转观察窗Curtain 窗帘Latch止动销，插销Valance窗帘箱Hanging窗帘Eyebrow舷窗眉板Pre-alarm预报警Trip脱扣，跳闸Preferential trip优先脱扣Transducer换能器synchronize（便）同步synchronize motor同步电机synchronous motor异步电机step motor步进电机diode二极管triode三极管audion三极管single phase单相three phase三相phase-in逐步引进phase-shafting相移retarding phase 滞后相位reversed phase倒相，相反relay继电器timer定时器trimmer微调电容器，调正片delay延时carrier载波，载波电流transponder发射器，应答器，询问机echo-sound回声测深仪radio navigation equipment无线电导航设备log计程仪auto-pilot自动驾驶仪gyro-compass电罗经barrier屏障，障碍，栅栏zenner barrier齐纳屏（使电只能单向流的半导体）radio beacon无线电信标pluse脉冲blanking plus 消隐脉冲induction感应，感应现象oscillation振荡Leak(v)渗，漏Leakage(n) 渗，漏Overhaul大修，彻底检修Hammer榔头Spanner扳手，扳头Ring spanner环形扳手，梅花扳手Allen key 内六角扳手，Box spanner套筒扳手Torque spanner扭力扳手Double-ended spanner双头扳手Monkey spanner活络扳手，活络管扳手Shifting spanner活络扳手Pipe spanner管子扳手Reamer铰刀Reaming （用）铰（刀扩）孔Countersink reamer锥形孔铰刀Wrench扳手，扳头Shisel凿子Calipers卡钳，两脚规Inside calipers内卡钳Bore 内孔Boroscopic inspection内孔表面检查Boroscope内孔表面检查仪Plug塞（子），（内燃机）火花塞Cock施塞，龙头Valve阀P/V valve P/V阀Strainer滤器Coarse strainer粗滤器Fine strainer精滤器Oil separator分油机Back pressure背压Pressure test压力试验Over speed 超速Over load超负荷Dafety device 安全装置Fly wheel飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的）Ladder 梯子Vertical ladder直梯Inclined ladder斜梯Accommodation ladder舷梯Pilot ladder引水员；软梯3-roller bending machine 三弯机abandon v. 弃船abolish v. 消除ABS 美国船级社acceleration n. 加速度accelerometer n. 加速度表accommodate v. 容纳accommodation deck起居(住舱)甲板accuracy n. 精度accurate synchro device准同步装置acetylene cutter 气割机acid-pickling n. 酸洗acoustics n. 音响效果adhesiveness n. 粘附力adjacent a.相邻的adjust v. 调节administration n. 行政管理admit v. 接纳adopt v. 采纳，采用affiliated factory 分厂，附属工厂aforementioned a.前述aft a. adv. n. （在）船艉aft peak 艉尖舱after service 售后服务ahead n. 正车air bottle 空气瓶air compressor 空压机air reservoir 气瓶air siren 汽笛air-tight test 气密实验alarm bell 警铃alignment n. 找中all waves 全波allowance n. 允值all position 全方位alternating current ( A.C.) 交流电ammonia n. 氨amplify v. 放大an automatic production line自动生产线analogous output 模拟输出analogue computer 模拟计算机anchor n. 锚anchor chain （cable chain）锚链anchor handling 锚操纵anchor windlass (chain windlass)起锚机anchorage buoy 系泊浮筒angular n. 角度antenna n. 天线anticorrosion precaution 防腐措施apparatus n. (pl. apparatus or apparatuses)仪器，器械，装置appearance n. 外观approval n. 批准，认可approve vt. 认可arbitrate v. 仲裁arc n. 弧度arduous a.艰难的arrange v. 布置，安排asbestos n. 石棉assemble v. 装配Assemble Language 汇编语言assembly n. 装配astern n. 倒车atmospheric survey 大气环流调查atomic power 原子能atomize v. 雾化authority n. 当局automatic control device自动控制装置automatic production line自动生产线automatic steering 自动操舵automatic submerged arc welding自动埋弧焊automatic telephone 自动电话aux. boiler 副锅炉aux. engine 辅机aux. engine room 辅机舱aux. machinery 辅机auxiliary means 辅助手段auxiliary system 辅助系统axial push 轴向推力backing n. 衬垫ballast piping 压载水管系ballast pump 压载泵ballast system 压载系统ballast water 压载水base n. 基准base point n. 基准点basic design 基本（方案）设计basic metal 母材battery unit 蓄电池组beam n. 波束beam n. 横梁bearing n. 轴承bearing hole n. 轴承孔bedplate n. 机座bell set 铃组bending machine 冷弯机berth n. (水平)船台，（船上）床铺berth or slipway fabrication船台装配bilge n. 舱底水bilge keel 舭龙骨bilge plate 舭板bilge pump 舱底水泵bilge system 舱底水系统binary system 二进位制blank n. 毛胚block n. 分段block or section fabrication分段或总段装配blood vessel 血管blower 风机blue collar worker 蓝领,工人boat deck 艇甲板bollard n. 带缆桩bolt n. 螺栓bolthead n. 螺栓头bottom n. 船底bottom plate 底板bottom structure 底板结构bow n. 船艏bow &stern structure 艏艉结构bow section 艏段branch company 分公司，子公司branch system 分系统bridge n. 桥楼bridge control 桥楼控制broadcast n. v. 广播broadcast station 广播站bronze sleeve 青铜套筒bulbous bow 球鼻艏bulk cargo 散装货物bulk-cargo carrier 散装货船bulkhead n. 隔舱壁bulkhead structure 隔舱壁结构bushing n. 衬垫butt joint 对接接头cabin n. 舱室cable fixture 电缆夹具calculation n. 计算calculator n. 计算器calibrate v. 校正calibration n. 校正cam n. 凸轮cam follower 凸轮附件camber n. 梁拱camshaft n. 凸轮轴capstan windlass（anchor winch）锚绞盘cargo n. 船货cargo oil 货油cargo –hold n. 货舱cargo-lifting n. 起货casing n. 罩壳cast iron piece 铸铁件casting n. 铸造cathode-ray type 阴极射线式CCS 中国船级社central control 集控centreline n. 中心线centrifugal a.离心的certificate n. 证书chain drive 链传动chain locker 锚链舱chain pipe 锚链管chain reaction 连锁反应chain stopper 制链器challenge n. v. 挑战chamfer v. 在边缘切斜面changeover switch 转换开关characteristics n.性能，特性，特征charge v. 充（电，气）check n. v. 检验chemical medium 化学介质China Classification Society(CCS)中国船级社China Ocean Shipping Company (COSCO) 中国远洋公司chip n. 芯片circle n. 圈子，团体class n. 船级classification n. 船级classification society 船级社cleanness n. 清洁度closed circulation 闭式循环clutch n. 离合器CO2 shielded arc welding 二氧化碳气体保护焊Coating n. 图层code n. 法典code display circuit 编码显示电路coefficients of ship form 船型系数cold processing 冷加工collision n. (船只)碰撞combustibility n. 可燃性combustion n. 燃烧combustion chamber 燃烧室combustion gas 燃气commanding telephone 指挥电话communication n. 通讯compartment n. 分隔舱compartment stuffing box隔舱填料函compass n. 罗经compass deck 罗经甲板compensate vt. 补偿competition n. 竞争completion drawing 完工图component n. 组成部分composition n. 成分组成compound excitation 复励comprehensive productivity综合生产能力compressed air 压缩空气compression (power)stroke n. 压缩冲程computer control console计算机控制台conceptual a. 概念的condensation n. 冷凝conductor n. 导体connecting rod 连杆connection n. 接头constant voltage 恒压constitute v. 构成consumables n. 消耗品consumption n. 消耗contact v. 触发container n. 集装箱continuous deck 连续甲板contract n. 合同contradiction n. 矛盾control component 控制元件control console 控制台control unit 控制装置converse method 反装法convertor n. 转换器conveyor n. 传送带coolant n. 致冷剂coolant(cooling agent)n. 制冷剂cooler n. 冷却器cooling system 冷却系统cooperation n. 合作coordinate n. 坐标core enterprise 核心企业corrosion n. 腐蚀corrugated a. 波纹状的course n. 航向cover n. 药皮CPP drive 可调浆传动crank cheek 曲柄夹板crankcase n. 曲柄箱crankpin n. 曲柄臂crankshaft n. 曲轴crankweb n. 曲柄臂crew n. (全体)船员cross section 截面crosshead n. 十字头cultivate v. 培养，培育current n. 电流current n. 洋流，水流current-impulse frequency convertor 电流-脉冲频率变换器curve n. 曲线cutting n. 切割cylinder n. 气缸cylinder block 气缸体cylinder cover (cylinder head) 缸盖cylinder liner 气缸衬套cylinder oil 气缸油cylinder wall 缸壁data impulse 数据脉冲davit n. 吊艇架deadweight ton(DWT) n.载重量，吨载量Decca receiver 台卡定位仪deck n. 甲板deck girder 甲板材deck longitudinal 甲板纵骨deck machinery 甲板机deck plate 甲板板deck structure 甲板结构deckhouse 甲板室deform v. 形变deliver v. 交货，交船delivery n. 交船，交货delivery ceremony 交船典礼derrick n. 吊杆design stage 设计阶段designation n. 名称，牌号designation n. 目的地detail design 详细（施工）设计detect v. 探测detect v. 侦察detection n. 探测deviation n. 位移dial n. 刻度盘diameter n. 直径differentia n. 差异digital computer 数字计算机digital output 数字输出direct current(D.C.)直流电direct drive 直接传动direct telephone对讲电话，直线电话directional finder 测向仪directional instrument 指向仪器directional stability 航向稳定性disc n. 圆盘discharge n. v. 排水dispensable a. 非必要的dispute n. v. 争端，争执distribute v. 分布distribute v. 分配，配电distribution n. 配电distribution box 分电箱distribution panel 区配电板distribution switch 配电开关distribution system n. 配电系统division n. 划分DNV 挪威船级社Dock n. 船坞dock trial 码头试验docking winch 带缆绞车Doppler effect 多普勒效应Doppler frequency offset多普勒频移Doppler sonar log多普勒声纳计程仪double bottom 双层底double-action a.双作用down-vertical welding 下行焊draft(draught)n. 吃水drainage n. 疏水，泄水drawing n. 图纸drawing instrument 绘图仪drift v. 漂移drinking water 饮用水drip-proof type 防滴式drive n. 传动drive mechanism 传动机构drive mechanism 传动装置drive unit 传动装置driven shaft 从动轴dry v. 烘干drydock n. 干船坞dynamic –pressure type 水压式echo signal 返回信号echo sounder 回声测深仪economic effect 经济效益edge preparation 边缘加工edge processing 边缘加工edger n. 刨边机eject v. 喷射elapse v. （时光）消逝electric brain 电脑electric load 负荷electrical arc 电弧electrical compass 电罗经electrical drive 电力托动electrical energy 电能electrical impulse 电脉冲electrical power 电力electrical shedding 放电electrical signal 电器信号electrical slag welding 电焊渣electrical unit 电器装置electrical user 电器设备electrical-driven a. 电动的electrician n. 电工electricity outfitting 电舾electrode n. 焊条electromagnetic contactor电磁接触器electromagnetic induction 电磁感应electromagnetic log 电磁计程仪electromagnetic sensor 电磁传感器electronic computer 电子计算机electronics n. 电子（学）element n. 机械零件element n. 要素emerge v. 崛起，兴起emergency control 应急控制emergency network 应急电网emergency power station 应急电站emergency radio transmitter应急无线电发信机emergency steering 应急操舵emergency switchboard 应急配电板emergency telegraph 应急传令钟emergent discharge 应急排放emergent service 应急使用enclose v. 封闭encounter v. 遭遇energy convertor 换能器engine foundation (engine seat )机座engine frame 机架engine oil 机油engine outfitting 机舾engine space 机舱engineer n. 轮机员engineer n. 工程师engineering and technical team工程技术队伍engineer vessel 工程船engine-room 机舱ensure v. 确保enterprise n. 企业EO 无人机舱equipment n. 设备error n. 误差essence n. 实质，本质evolve v. 渐进，进化，演变excessive a. 过量的，极度的excitation n. 励磁excite v. 激励exhaust port 排气口exhaust stroke 排气冲程exhaust valve 排气阀expand v. 扩张，扩建expansion n. 展开图expansion stroke 膨胀（作工）冲程expansion tank 膨胀箱experiment n. 实验exterior force 外力extinguish v. 灭火F.O.meter 燃油流量计F.O．tank 燃油舱Fabricate v. 装配，制作fabrication n. 装配facile adaptability 灵活的适应性facsimile transmission(fax)传真fairing n. 光顺体，流线体fair-lead n. 导缆孔fashioned steel 型钢fast speed (rapidity)快速性fathometer n. 侧深仪feed v. 馈给feed circuit 馈电线路fillet seam 角焊缝fillet welding 角焊filter n. 过滤器. 过滤fine a. 纤细的finished product 成品fire alarm 火警fire hazard 火灾fire pump 消防泵fire-fighting system 消防系统fire-resistant a.耐火的fixed part 固定件flash signal light 闪光信号灯flat fillet seam 平角焊缝flexibility n. 挠性flexible coupling 挠性联轴节float launching 漂浮下水floatability n. 漂浮性floating positively 正浮floating production storage unit(FPSU) 浮式生产储油轮flood v. 进水floodability n. 不沉性floor plate 肋板fluctuate v. 波动fluctuation n. 波动flush v. 清洗flushing agent 清洗剂flux n. 焊剂flywheel n 飞轮foam n. 泡沫folding machine 折边机for home use 国内用forced lubrication 强制润滑forced ventilation 机械通风fore perpendicular 艏垂线forecastle n. 艏楼foreign trade 外贸forging n. 锻造formation n. 构成，结构frame n. 肋骨framework n. 框架framing block 肋骨框架分段free end 自由端freeboard n. 干舷freighter n. 货船Freon n. 氟利昂frequency n. 频率frequency difference latching频率锁定frequency regulation 调频fresh water （F.W.）淡水fresh water production plant造水装置friction resistance 摩擦阻力fuel n. 燃料fuel nozzle 喷油嘴fuel oil 燃油fuel oil （F.O.）燃油fuel pipeline 燃油管系full-load a. 满载的full-load displacement 满载排水量funnel n. 烟囱galley n. 厨房gantry n. 龙门架gas cutting 气割gas tight seal 气密密封gas turbine engine 燃气轮机gas welding 气焊gear n. 齿轮gear drive 齿轮转动geo-physical propecting vessel地球物理探测船GL 西德劳氏船级社grant v. 给予……的权利gravity centre 重心gravity welding 重力焊groove v. 开坡口ground v. 接地group n. (企业)集团growth n. 生长，发育guarantee n. v. 保证general description 概述general-purpose a.通用的generating set 发电机组geometrical characteristics 几何特征geometrical principle 几何原理gravity launching 重力下水guided-missile frigate 导弹护卫舰gyro n. 陀螺仪gyro compass 陀螺罗经，回转罗经H.D.Heavy Machinery Co. Ltd. H.D.重机股份有限公司Halogen n. 卤素hand control 手控hand level 手柄hand steering 手动操作hand wheel 手轮handle v. 操纵harbour n. 港口，停泊harbour generator 停泊发电机hardware n. 硬件hatch trunk 舱口围壁hawsepipe n. 锚链筒he water pressure system 水压系统headquarters n. 总部，厂部headroom n. 甲板间高度heat exchanger 热交换器heating n. 供暖heavy current n. 强电heavy oil 重油heel n. 横倾hereinbelow adv. 在下文high frequency 高频high-speed boat 高速艇horizontal a.水平的，卧式的horsepower(hp) n. 马力hose n. 软管hot processing 热加工hot work 火工hull n. 船体hull cleanness 船体光顺性hull construction 船体结构hull form 船型hull line 船体线型hull structure 船体结构human brain 人脑humidify v. 增湿hydraulic a. 液压的hydraulic fluid 液压流体hydraulic machine 液压机hyperbolic curve receive双曲线定位仪identify vt.识别ignite v. 点火ignition n. 点火illumination n. 照明illustration n. 生动的说image display system 图象显示系统IMCO 政府间海事协商组织impact n. 冲击implication n. 含义impulsator n. 推动器，脉冲发生器impulse-type a.脉冲式的impurity n. 杂质inclination n. 倾斜inclination test 倾斜试验incline v. 倾斜index n. 索引indication n. 显示indicator n. 显示仪indicator n. 指示器indicator light 指示灯indicator valve示功阀inert gas 惰性气体inertia n. 惯性inertia platform 惯性平台inevitable a.不可避免的initial metacentric height 初稳心高inject n. 喷射injecting system 喷油系统injector n. 喷油器inner bottom longitudinal 内底纵骨inner bottom plate 内底板inner ring 内环input n. v. 输入inspector n. 质检员installation n. （船上）安装installation error 安装误差instancy speed 瞬时速度instrument n. 仪表,仪器insulating material 绝缘材料insulation n. 绝缘intake n. 吸入intake port 汲气口intake valve 进气阀integral casting 整体浇铸intention n. 意向intercommunication (intercom)n.内通，内部通讯interfering moment 干扰力矩intermediate bearing 中间轴承intermediate shaft 中间轴internal combustion engine 内燃机international authorities 国际当局Internet 因特网（国际互连网）introduce v. 引进，引入，介绍iron powder electrode 铁粉焊条jig n. 胎架joint design 联合设计journal n. 轴颈keel n. 龙骨keel plate 龙骨板keep station 定位kerosene test 煤油实验key enterprise 骨干企业kilohertz 千赫kinetic energy 动能knot n. 节labyrinth n. 迷宫，曲径land-based a. 路基的landing-place n. 码头lap joint 搭接接头large-computer(mainframe computer) n. 大型（计算）机，主机lay v. 敷设length n. (一)节，（一）段level n. 液位level gauge 液位计level relay 液位继电器license n. 许可证life line 生命线life-belt n. 救生圈life-boat n. 救生艇life-jacket n. 救生衣life-or-death a.生死攸关的life-raft n. 救生筏life-saving n. 救生lifting capacity 起重能力light current 弱电lighting n. 照明light-ship displacement (light-load displacement)轻载排水量lines lofting 线型放样lines offsets 型值lines plan 线型图lining n. 衬垫load distribution 负荷分配load line mark 载重线标志load transfer 负荷转移local strengthening 局部加强locate v. 定位lock washer 锁紧垫片lofting n. 放样log n. 计程仪logical a.逻辑的long bridge 长桥楼longitudinal a.纵向的longitudinal (uniflow)scavenge 直流扫气longitudinal bulkhead 纵隔舱壁longitudinal framing 纵向构架loop n. 回路loop antenna 环状天线Loran receiver 劳兰定位仪Loudspeaker n. 扬声器low speed 低速lower deck 下甲板LR 英国劳氏船级社lube oil 润滑油lube oil(L.O.)滑油lube oil pump 滑油泵lubricant n. 润滑剂lubricant film 润滑油膜lubricating oil 滑油lubrication system 滑油系统M.E.engine room 主机舱Machine v. 机加工machinery n. 机械machinery set 机组machinery workshop 机电车间machining n. 机加工machining workshop 机加工车间magnetic compass 磁罗经magnetic field 磁场magnetic needle 磁针magnetic object 磁性物体magnifier n. 放大器magnify v. 放大magnitude n. 大小main bearing 主轴承main engine (ME) 主机main generating set 主发电机组Main Group 1 第一大部分main hull 主船体main network 主电网main power station 主电站main switchboard 主配电板maintenance n. v. 维护，保养marker n. 厂商man power resource 人力资源management n. 生产管理maneuver v. n. 操纵maneuverability n. 操纵性maneuvering console 操纵台maneuvering system 操纵系统manual work 手工劳动manufacture n. &v. 生产，制造marine crane 船用起重机marine diesel engine 船用柴油机marine engineer 机电工程师marine engineering research institute造机研究所marine geological research vessel海洋地质调查船mark v. 标出mast lightmaster controller 主令控制器Master degree 硕士学位material n. 材料material marking 下料mathematical a.数学的mathematical lofting skill数学放样技术maximum(max.)n. 最大means n. 手段，工具measurement laboratory 计量实验室measuring meter 测量仪表measuring point 测量点mechanical energy 机械能mechanical launching 机械下水mechanical processing 机加工mechanical unit 机械装置medium speed 中速medium wave 中波medium-computer n.中型（计算）机member n. 构件memory n. 储存器，内存memory and storage system储存系统merchant ship 民用船mercury n,水银meridian n. 子午线metacentre n. 稳心metal recovery 金属回收率metallic equipment 冶金设备microclimate n. 小气候microcomputer n. 微机microprocessor n. 微处理器midship n. a. adv. 舯部military ship 军用船miller n. 铣床minicomputer n. 小型（计算）机minimize v. 降至最低minus push 负推力minus value 负值miscellaneous a. 杂项的mobilize v. 动员model case 样箱model plate 样板model rod 样棒moderate a. 中型的modern enterprise system现代企业制度modus n. 操纵法（pl. modi）monitor v. 监视monitoring device 监控装置moor v. 系泊motive power 原动力motor n. 电动机mould loft 放样台mouth n. 河口moving part 运动件multi-purpose a.多用途的，综合的multi-stage n. 多级mutual benefit 互惠互利nautical mile 海里naval architect 造船设计师navigating instrument 导航仪器navigating zone 航区navigation computer 导航计算机navigation equipment 导航设备navigational light 航行灯navy n. 海军navy underway replenishment ship海军航行补给船NC cutting machine 数控切割机nerve cell 神经细胞nesting n. 套料network n. 电网nil n. 零，无NK 日本海事协会non –ferrous metal 有色金属non-restrictive a.自由的，不受限制的non-standard product 非标产品non-transparent a. 不透明的normal displacement 正常排水量normal shipping 正常营运nozzle n. 喷嚏numbering system 计算系统numeral n. 数字numerical control (NC)数控numerical control cutter 数控切割机nut n. 螺母observation n. 观察occasion n. 盛事，盛举ocean-going vessel 远洋船oceanographic research vessel海洋调查船offshore service 近海作业oil charging piping 注油管系oil consumption 油耗oil filling port 注油口oil mist 油雾oil refinery 炼油厂oil tanker 油船oil-resistant a.耐油的oil-tight n. 油密Omega/satellite integrated navigation instrument 奥米加/卫星导航系统one-side welding单面焊接，双面成形one-way a.单向的open chamber 开放式燃烧室open circulation 开放循环opening n. 开口operating cycle 工作周期operation n. 施工operation n. 运行，运转operation surroundings 作业环境operator n. 操纵员opportunity n. 机遇optical projector 光学仪器optics n. 光学orbit n. 轨道order n. v. 订单，定购oscillation n. 振荡oscillation current 振荡电流outboard adv. 向舷外outer appearance 外观outer ring 外环outfitting n. 舾装output n. 输出overload v. 过载owner n. 船东owner’s representative船东代表oxide n. 氧化皮paint n. 油漆pain-taking a.艰巨的painting n. 涂装painting n. 涂装，油漆工艺palletizing management 托盘管理parallel n. 并联v. 并车parallel of generators 发电机并车parameter n. 参数part n. 部件，机械部件part fabrication 部装particle n. 颗粒party n. (谈判或合同之)一方passage n. 通道passageway n. 通道passenger-cargo vessel 客货船performance n. 性能permanently adv. 永久的perpendicular n. 垂线personnel n. 全体人员personnel n. 人员，人事phase angle 相角phase sequence 相序phase –sensitive rectifier相敏整流器physical quantity 物理量physical-chemical experiment理化实验physical-chemical experimental center理化中心实验室pillar n. 支柱pilot n. 驾驶员，领航员，舵轮pipe connection 管子接头pipe flange 管子法兰piping system 管系piston pin 活塞环piston pin 活塞梢piston stroke 活塞冲程pitch n. 纵摇plan n. 图纸plane n. 平面plane v. 整平planing machine 校平机plant n. （成套机电）设备platform n. 平台pneumatic tool 气动工具pointing of direction 指向poisonous gas 有毒气体pollution n. 污染poop n. 艉楼port n. 左舷portable light 手提灯postdoctoral centre 博士后工作站potable water 饮用水pour v. 涌入，源源不断power amplifier 功率放大器power plant 动力装置,(火力)电厂power station 电站power supply 电源，供电power system 电力系统,动力系统practice n. 习惯做法preamplifier n. 前置放大器pre-combustion chamber预燃燃烧室pre-heat v. 预热pressure container 压力容器pressure relay 压力继电器pressure sensor 压力传感器pressure tank 压力柜pretreat v. 预处理primary radio transmitter主无线电发信机prime mover 原动机primer n. 底漆primer painting 涂底漆principle dimensions 主尺度process n. 工艺，流程v. 加工，处理production efficiency 生产效率production line 生产线production procedure 生产程序program n. 程序projection plane 投影面prolong v. 延长promote v. 促进，晋升propeller n. 螺旋桨proportion n. 比例propulsion efficiency 推进效力propulsion plant 推进装置protection type 保护式provision n. 食品pump n. 汞purity v. 净化push rod 顶杆push-pull magnetic amplifier推挽磁放大器pyramid method 正装法quality assurance 质量保证quality control 质量控制quality management 质量管理quality policy 质量方针quay n. (顺岸式)码头quiescent a.安静的radar n. 雷达radio beacon station 导航台radio communication equipment无线电通讯设备radio directional finder 无线电测向仪radio message 无线电报radio receive 无线电接收机radio room 报房radio station 电台radio transmitter 无线电发信机。
船舶专用英语汇总
船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多∙船舶专业英语词汇∙船体制图常用英中名词术语对照∙船舶英语(页1) - 设计学习- 千岛热线论....∙船体结构英语∙船舶英语手册1--5.word可编辑.∙Navis.gr - 3Examination Questions For...∙船舶图纸符号大全∙货运保险鉴定常用词汇. 专业.专注.。
船舶专业英语基础词汇
1.hull form船型2.principal dimensions主尺度3.length over all 总长4.length between perpendiculars垂线间长5.beam /girder横梁6.side girder 纵桁7.depth 型深8.draught 吃水9.load line 载重线10.light water line 空载水线11.deep water line 满载水线12.deck line 甲板线13.moulded dimensions 型尺寸14.base line 基线15.amidship 船舯16.ordinate /station 站位17.stem 船首18.stern 船尾19.after sheer 尾舷弧20.bulbous bows 球鼻艏21.camber 梁拱22.transverse 横向的23.longitudinal strength 总纵强度24.reserve buoyancy 储备浮力25.draught forward 艏吃水26.draught at stern 艉吃水27.down and trimmed by the head首倾28.air draught 干舷freeboard29.rise of floor 船底斜度30.gross tonnages 总重t tonnages 净重32.form coefficient 船型系数33.water-plane coefficient 水线面系数34.midship section coefficient 中横剖面系数35.block coefficient 方形系数36.prismatic coefficient棱形系数37.rudder 舵38.center line of rudder stock 舵杆中心线39.bilge 舭部40.keel 龙骨41.line plan 型线图42.offset table 型值表43.starboard 右舷44.portside 左舷45.fairing 光顺46.buttock line 纵剖线47.general arrangement plan（GA）总布置图48.midship section 横剖面图49.cross section 横剖面50.capacity plan 舱容图51.dry cargo 干货52.multipurpose ships 多用途船53.container ships 集装箱船54.roll-on/roll-off Ro-Ro客滚船55.coastal cargo 沿海客货轮56.dredge挖泥船—57.drillship 钻井船:58.icebreaker 破冰船59.bulk carriers 散货船60.crude oil tanker 原油油轮61.chemical ships 化学品船62.cruise ships 游船63.passenger line邮轮64.aircraft carrier 航母65.yacht 游艇66.tug boat 拖船67.flare 外飘68.tumblehome 船舷内倾69.integration 积分70.moment of inertia 惯性矩71.LCF longitudinal center offlotation 浮心纵向坐标72.center of gravity 重心73.subdivision 分舱74.optimization 优化75.bulkhead 舱壁76.stiffener 加强筋77.web frame 强肋骨78.hogging 中拱79.sagging 中垂80.bending stress 弯曲应力81.bending moments 弯矩82.hydrostatic pressure 静水压力83.hydrodynamic ~~ 动水压力84.local stresses 局部强度85.buoyancy 浮力86.magnitude 大小幅度87.unevenly 不均匀地88.still water 静水89.shearing forces剪力90.vibration 振动91.engines 主机92.propeller 螺旋桨93.pitching 纵摇94.resonance vibration 共振95.torsion 扭转96.forepeak 艏尖舱97.afterpeak 艉尖舱98.weather deck 露天甲板99.tank top 内底100.cargo holds 货舱101.classification society 船级社102.flag state 船旗国103.forecastle deck 艏楼104.ballast tank 压载舱105.bridge 驾驶室106.deckhouse 甲板室107.ship resistance 船舶阻力108.frictional resistance 摩擦阻力109.pressure （form）resistance 压力阻力110.wave resistance 兴波阻力111.air resistance 空气阻力112.propellers 螺旋桨113.rotations 旋转114.cavitation 空泡115.initial stability 初稳性ger angle stability 大倾角稳性117.intact stability 完整稳性118.damaged stability 破舱稳性119.watertight 水密的120.reserve buoyancy 储备浮力121.float upright 正浮122.vector 矢量123.hydrostatic tables 静水力曲线表124.righting arm 复原力臂125.righting moment 复原力矩126.stability moment 稳性力矩127.neutral axis中性轴128.double - hull , double bottom 双壳双底1.American Bureau of Shipping 美国船级社。
船舶英语必备词汇
船舶英语必备词汇船舶英语必备词汇要学好英语，词汇量是不能少的，如果词汇量多，那英语不会差到哪里。
下面是给大家整理的一些船舶英语必备词汇的学习资料，希望对大家有所帮助。
船舶英语词汇dugout独木舟barge驳船kayak(爱斯基摩人的)木排outrigger桨叉架船rowing boat划艇(美作：rowboat)gondola(意大利的)长平底船whale mother ship捕鲸母船hydrofoil水翼船catamarans双体船dredger挖泥船boat船brig，brigantine双桅船canoe小船，独木舟caravel快帆船cargo boat货船coaster近海贸易货船cod-fishing boat捕鳕鱼船whaler捕鲸船collier运煤船battleship战船shallop小型战船coastguard cutter，coastguard vessel巡逻艇，缉私艇revenue cutter缉私船patrol boat巡逻艇minelayer布雷艇minesweeper扫雷艇torpedo boat鱼雷艇frigate轻护航舰gunboat炮舰submarine潜水艇destroyer驱逐舰corvette轻巡洋舰cruiser巡洋舰aircraft carrier航空母舰ferry，ferryboat渡船，渡轮fishing boat渔船freighter货船galleon大型帆船galley大划桨船hovercraft气垫船icebreaker破冰船launch艇lifeboat救生艇lighter驳船liner，ocean liner远洋班轮merchant ship，merchantman商船motorboat摩托艇outboard尾部装有马达的小艇paddle steamer，paddle boat明轮船passenger boat客船piragua，pirogue独木舟raft木筏rowing boat划艇sailing boat，sailing ship帆船schooner纵帆船ship船skiff小艇sloop单桅船steamer，steamship汽轮tanker油轮trawler拖网渔船tug，tugboat拖轮vessel船yacht游艇yawl船载小艇船舶工程专业英语口语词汇1、柴油日用柜Diesel oil daily tank2、柴油澄清舱Diesel oil setting tank3、燃油日用柜Fuel oil daily tank4、燃油澄清舱Fuel oil setting tank5、滑油澄清舱Lubricating oil setting tank6、滑油储藏舱Lubricating oil store tank7、滑油循环舱Lubricating oil circulating tank8、燃油溢油舱Fuel oil overflow tank9、燃油油渣舱Fuel oil sludge tank10燃油深舱Fuel oil deep tank11滑油污油舱Lubricating dirty oil tank12滑油溢油舱Lubricating oil overflow tank13滑油油渣打舱Lubricating oil sludge tank14主机淡水膨胀水箱M.E fresh water expansion tank 15付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜Fresh water pressure tank17、热水压力柜Hot water pressure tank18、饮水压力柜Drinking water pressure tank19、淡水舱Fresh water tank20、饮水舱Drinking water tank21、锅炉水舱Boiler water tank22、分油机工作水箱Purify operating water tank23、汽缸油日用柜Cylinder oil daily tank24、尾管滑油重力柜Gravity tank of tube oil25、排气水封箱Exhaust seal water tank26、蒸馏水水舱Distilling water tank27、污水井Bilge well1、滑油系统Lubricating oil piping system2、燃油系统Fuel oil piping system3、海水系统Sea water piping system4、缸套水系统Cylinder cooling water piping system5、启动空气系统Start air piping system6、控制空气系统Control air piping system7、排气系统Exhaust piping system8、日用供水系统Daily water piping system9、蒸汽系统Steam piping system10 、锅炉给水和凝水系统Feed water and condensate ofboiler piping system11、燃油净油系统Fuel oil purified piping system12、燃油输送系统Fuel oil transport piping system。
船舶英语词汇大全
船舶英语词汇大全一、船舶基本结构词汇1. 船体（Hull）：船舶的主体部分，包括船壳、甲板和舾装。
2. 船壳（Shell）：船体的外表面，起到防水、承重的作用。
3. 甲板（Deck）：船舶的顶部平面，用于行走、作业和装载货物。
4. 舷窗（Porthole）：船体两侧的窗户，用于通风和采光。
5. 舷梯（Jacob's ladder）：连接船舶与码头的小梯子，便于人员上下船。
6. 舵（Rudder）：控制船舶方向的装置，位于船尾。
7. 锚（Anchor）：固定船舶位置的器具，用于抛锚停泊。
8. 船锚链（Anchor chain）：连接船锚与船舶的链条。
9. 船舶龙骨（Keel）：船体底部的一条纵向构件，起到支撑作用。
二、船舶动力装置词汇1. 船舶主机（Main engine）：船舶的动力源，通常为柴油机或蒸汽轮机。
2. 船舶辅机（Auxiliary engine）：为船舶提供辅助动力的装置，如发电机、空压机等。
3. 螺旋桨（Propeller）：将主机产生的动力转化为推力的装置，位于船尾。
4. 柴油机（Diesel engine）：以柴油为燃料的内燃机，广泛应用于船舶动力装置。
5. 蒸汽轮机（Steam turbine）：利用蒸汽驱动叶轮做功的热力发动机。
6. 燃油喷射泵（Fuel injection pump）：柴油机燃油系统中，将燃油高压喷射到燃烧室的装置。
三、船舶导航设备词汇1. 罗经（Compass）：指示船舶航向的导航仪器。
2. 船用雷达（Marine radar）：用于探测船舶周围水域障碍物的电子设备。
3. GPS导航仪（GPS navigator）：全球定位系统导航设备，用于确定船舶位置和航迹。
4. 电子海图（Electronic chart）：显示海域地理信息的电子地图。
5. 船舶自动识别系统（S）：用于船舶识别、追踪和避碰的通信系统。
四、船舶通讯设备词汇1. 船用无线电（Marine radio）：用于船舶与船舶、船舶与陆地之间通信的无线电设备。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
船舶专业英语词汇（按英文字母排序）a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用adjustable-pitch 可调螺距式admiralty 海军部aerostatic 空气静力学的aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍anti-roll f ins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额axial advance 轴向进速ball bearing 滚珠轴承ball valve 球阀bar 型材barge 驳船batten 压条，板条bed-plate girder 基座纵桁Benoulli’s law 伯努利定律bitt 单柱系缆桩blue peter 出航旗boarding deck 登艇甲板boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索Bonjean curve 邦戎曲线boom 吊杆bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽break bulk 件杂货breast hook 艏肘板bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程cant beam 斜横梁cant frame 斜肋骨1cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crossing range 航程cup and ball jo int 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计2diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drill ship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计E.H.P 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electro hydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺raised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可浸长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding hatch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边3following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成组建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guy line 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling)取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷4imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launching equipment （向水中）投放设备VLCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表meta center 稳心meta centric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面mid-ship section 舯横剖面mid-ship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏5more shape to the shell 船壳板的形状复杂mould loft 放样间multi-hull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇normal 法向的，正交的normal operating condi t ion 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bi t ts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfi t ter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fi t ter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证6quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo I taliano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况sea-keeping 适航性seasickness 晕船sea-worthness 适航性sea-worthness 适航性section modulus 剖面模数sections 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side keelson 旁内龙骨single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力slamming 砰击slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳7spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stable equilibrium 稳定平衡static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem contour 艏柱型线stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Water-plane Area Twin Hull) 小水线面双体船sway 横荡tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air condi t ioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性Voith-Schneider propeller 外摆线直翼式推进器8wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力web beam 强横梁wetted surface 湿表面积windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁9。