质量英语词汇大全(中英对照)

合集下载

质量英文单词

质量英文单词

部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control? ?生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA:Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer? ?工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing? ?制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点(CR)MAJOR DEFECT:主要缺点(MA)MINOR DEFECT:次要缺点(MI)MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限CPI:Continuous Process Improvement 连续工序改善Compatibility:兼容性Marking:标记DWG rawing图面Standardization:标准化Consensus:一致Code:代码ZD:Zero defect零缺点Tolerance:公差Subject matter:主要事项Auditor:审核员BOM:Bill of material物料清单Rework:重工ID:identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR:First Piece Inspection Report首件检查报告FAA:首件确认SPC:统计制程管制CP: capability index(准确度)CPK: capability index of process(制程能力)PMP:制程管理计划(生产管制计划)MPI:制程分析DAS efects Analysis System? ?缺陷分析系统PPB:十亿分之一L/N:Lot Number批号Version:版本Quantity:数量Valid date:有效日期MO: Manafacture Order生产单TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT) DPPM: Defect Part Per Million(不良率的一种表达方式:百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC:允收REJ:拒收S/S:Sample size抽样检验样本大小SI-SIV:Special I-Special IV特殊抽样水平等级ISO:国际标准化组织ISA:Industry Standard Architecture工业标准体制结构PDCA:管理循环Plan do check action计划,执行,检查,总结WIP:在制品(半成品)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册AVL :认可的供货商清单(Approved Vendor List) QCD: Quality cost delivery(品质,交期,成本)KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S:Quality/Reliability/Service质量/可靠度/服务NTF:No trouble found误判CIP:capacity improvement plan(产能改善计划)MRB:material review board(物料审核小组)MRB:Material reject bill退货单JIT:just in time(即时管理)5S:seiri seiton seiso seiketsu shitsuke(整理,整顿,清扫,清洁,修养)SOP:standard operation process(标准作业程序)SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction(作业指导书)FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告ISAR :首批样品认可(Initial Sample Approval Request)-QCC :品管圈(Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)AOQ:Average Output Quality平均出货质量AOQL:Average Output Quality Level平均出货质量水平FMEA:failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA:Customer Simulate Analysis客户模拟分析SQMS:Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP:Quality Improvement Plan品质改善计划CIP:Continual Improvement Plan持续改善计划来料品质回馈单)SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA:PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (品质工程表)DRP :运销资源计划(Distribution Resource Planning) DSS:决策支持系统(Decision Support System)EIS :主管决策系统(Excutive Information System)ERP:企业资源规划(Enterprise Resource Planning) FMS :弹性制造系统(Flexible Manufacture System) KM? ?:知识管理(Knowledge Management)4L :逐批订购法(Lot-for-Lot)LTC :最小总成本法(Least Total Cost)LUC :最小单位成本(Least Unit Cost)MES :制造执行系统(Manufacturing Execution System) MPS :主生产排程(Master Production Schedule)MRP :物料需求规划(Material Requirement Planning) MRPⅡ:制造资源计划(Manufacturing Resource Planning) OEM :委托代工(Original Equipment Manufacture) ODM :委托设计与制造(Original Design & Manufacture) OLAP:线上分析处理(On-Line Analytical Processing) OLTP:线上交易处理(On-Line Transaction Processing) OPT :最佳生产技术(Optimized Production Technology) PDCA:PDCA管理循环(Plan-Do-Check-Action)PDM:产品数据管理系统(Product Data Management)) RCCP:粗略产能规划(Rough Cut Capacity Planning)SCM :供应链管理(Supply Chain Management) SFC :现场控制(Shop Floor Control)TOC:限制理论(Theory of Constraints)TQC :全面品质管制(Total Quality Control)S/T:Standard time标准时间TPM:total production maintenance:全面生产保养IT:information technology信息技术,资讯科学CEO:Chief Executive Officer执行总裁COO:Chief Operaring Officer首席业务总裁SWOT:Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence:专业能力Communication:有效沟通IDP:Individual Development Plan个人发展计划MRP:Material Requirement Planning物料需求计划MAT'S:Material材料LRR:Lot Rejeet Rate批退率ATIN:Attention知会5W1H:When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement 人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information人力,机器,材料,方法, 市场,管理,资金,资讯Pre-Inspection Area 待检区。

质量英语词汇大全(完整版)

质量英语词汇大全(完整版)

质量英语词汇大全(完整版) AABC analysis ABC 分析Abnormality 不正常性Abscissa 横坐标Absolute deviation 绝对离差Absolute dispersion 绝对离势Absolute error 绝对误差Absolute frequency 绝对次数Absolute number 绝对数Absolute reliability 绝对可靠度Absolute term 绝对项Absolute value 绝对值Absolute variation 绝对变异Abstract number 抽象数Abstract unit 抽象单位Accelerated factor 加速系数,加速因子Accelerated life test 加速寿命试验Accelerated test 加速试验Acceleration 加速度Acceptable limit 允收界限Acceptable process 允收制程水平Acceptable quality 允收品质Acceptable quality level (AQL) 允收质量水平Acceptable reliability level (ARL) 允收可靠度水平Acceptability 允收性Acceptability criterion 允收标准Acceptance 允收,验收Acceptance, probability of 允收机率Acceptance, region of 允收区域Acceptance and rejection criteria 允收与拒收准那么Acceptance boundary 允收界限Acceptance coefficient 允收系数Acceptance control chart 验收管制图Acceptance cost 验收费用Acceptance criteria 允收准那么Acceptance error 允收误差Acceptance inspection 验收检验Acceptance limit 允收界限Acceptance line 允收线Acceptance number 允收〔不良品〕数Acceptance plan 验收打算Acceptance procedure 验收程序Acceptance/rectification scheme 允收/精选方案Acceptance sampling, attribute 计数值验收抽样Acceptance sampling, variable 计量值验收抽样Acceptance sampling plan 验收抽样打算Acceptance sampling scheme 验收抽样方案Acceptance test 验收试验Acceptance value 允收值Acceptance zone 允收区域Acceptance product 允收品Accepting lot 允收批Access time 接近时刻,故障诊断时刻Accessibility 可接近性Accident rate 意外率Accidental error 偶误,偶然误差Accidental fluctuation 偶然波动Accidental movement 意外移动Accounting test 验算〔决算〕试验Accumulated operating time 累积操作时刻Accuracy 准确度Accuracy of data 数据准确度Accuracy of estimation 估量准确度Accuracy of the mean 平均数准确度Achieved availability 实际可用度Action 行动,措施Action, corrective 矫正行动〔措施〕Action control chart 行动管制图Action limit 行动界限Active line 行动线Active maintenance time 实际爱护时刻Active parallel redundancy 主动并复联〔置〕Active preventive maintenance 现行预防爱护时刻Active redundancy 主动复联〔置〕Active repair time 实际修复时刻Active standby 主动备用Active time 运用时刻Actual frequency 实际次数Actual limit 实际界限Actual range 实际全距Actual value 实际值Adaptability 可适应性Adaptive control 修改管制Addition theorem 加法定理Additivity 加法性,可加性Adjusted average 修正平均数Adjusted value 修正值Adjustment factor 调整系数Administration time for a repair 修复之治理时刻Administrative time 治理时刻Adopted value 采纳值Advisory Group on Reliability of Electronic Equipment (AGREE) 电子装备可靠度顾问团Aeronautical Radio, Incorporated (ARINC) 航空无线电公司After-sales service 售后服务Age 年限Age at death 死亡年限Age at failure 失效年限Age-based maintenance 年限基准爱护Aggregative method 综合法Aging 老化Agreement of quality assurance 质量保证之协议Agreement on verification method 验〔查〕证方法之协议Alarm signals 警告〔报〕讯号Alert time 待命时刻Algebraic sum 代数和Algorism (Algorithm) 阿拉伯数字计数法Alias 假名Alienation 余相关Alignment chart 列线图Allocation 配当Allocation of reliability 可靠度配当Allowable percent defective (Acceptable quality level, AQL) 允收不良率〔允收质量水平〕Allowance 允差,裕度Alternative hypothesis 对立假设American Management Association (AMA) 美国治理协会American National Standards Institute (ANSI) 美国标准协会American Society for Quality Control (ASQC) 美国质量治理学会American Society for Mechanical Engineers (ASME) 美国机械工程师学会American Society for Testing and Materials (ASTM) 美国材料试验学会American Standard Association (ASA) 美国标准协会American Statistical Association (ASA) 美国统计协会American War Standards (AWS) 美国战时标准Ambient condition 周遭条件Analysis, sequential 逐次分析Analysis by accumulated frequency 累积法,累积次数分析Analysis by non-accumulated frequency 次数法,非累积次数分析Analysis of correlation 相关分析Analysis of covariance 共变异数分析Analysis of means (AVON) 平均数分析Analysis of problem 问题之分析Analysis of variance (ANOVA) 变异数分析Analysis sample 分析样本Analytical error 分析误差Angular transformation 角度转〔变〕换Anti-logarithm 逆对数Anti-mode 逆众数AOQL Sampling Table 平均出厂质量界限抽样数Applicability 应用性Applied statistics 应用统计学Apportionment of reliability 可靠度配当Apportionment techniques 配当技术Appraisal cost 鉴定成本,评估成本Appraisal system 评估制度Appraisal of quality 质量评估Approach to sequential testing 逐次试验法Approval of processes and equipment 核准制程与设备Approximate mode 近似众数Approximate number 近似数值Approximation 近似法,概算AQL (Acceptable quality level) 允收〔质量〕水平Arbitrary average (Assumed average,Arbitrary mean) 假定平均数Arbitrary origin 假定原点Arbitrary scale 假定标度Area bar chart 面积条图Area chart (diagram, graph) 面积图Area sampling 地区抽样Arithmetic average 算术平均数Arithmetic cross 算术交叉Arithmetic graph 算术图Arithmetic line chart 算术线图Arithmetic mean 算术平均数Arithmetic paper 算术纸Arithmetic probability paper 算术机率纸Arithmetic progression (Arithmetic series) 算术级数,等差级数Arithmetic scale 算术标度,等差标度Arithmetic series 算术级数,等差级数Army Ordnance Table 陆军兵工署〔抽样〕表Army Service Forces Table 陆军〔抽样〕表序列Array 序列Array distribution 序列分配〔布〕Array of data 数据序列Assemble 装配〔组立〕Assembled product 装配品Assembly 装配件Assembly inspection 装配检验Assembly quality analysis report 装配质量分析报告Assessed failure rate 评估失效率Assessed mean active -maintenance time 评估时刻现行爱护时刻Assessed mean life 评估平均寿命Assessed mean time between failures 评估平均失效间格时刻Assessed mean time to failure 评估平均失效前时刻Assessed reliability 评估可靠度Assessed value 评估值Assessment of subcontractor 分包商之评鉴Assignable cause (Special cause) 非机遇缘故〔专门缘故〕Assignable variation 非机遇变异Associated dependent variable 相联因变数Associated variate 相联变量Association coefficient 相联系数Association of attribute 品性相联Association table 相联表,联合表Assumed mean (Assumed average,Arbitrary average) 假定平均数Assumed median 假定中位数Assumed origin 假定原点Assurance quality 保证质量Assurance function 保证功能Asymmetrical distribution 不对称分配〔布〕Asymmetry 不对称Asymptotic distribution 趋近分配〔布)At random 随机Attribute 计数值,属性Attribute classification 品性分类Attribute data 计数数据Attribute inspection 计数值检验Attribute sampling 计数值抽样Attribute sampling plan 计数值抽样打算Attribute testing (Go no-go testing) 计数值试验〔通过与不通过试验〕Attribute value 计数值Audit 稽核Audit for reliability 可靠度稽核Audit of decision 稽核决策Audit plan 稽核打算Audit report 稽核报告Auditing report 稽核报告Auto-correlation 自动相关Automatic switch-over redundancy 自动切换复联〔置〕Automatic test equipment (Am) 自动试验装备Auto-regression 自动回来Availability 可用性,可用度Average (Mean) 平均数,平均值Average, grand 总平均Average, moving 移动平均数Average, sample 样本平均数Average, standard error of 标准误平均数Average, universe 群体平均数Average, weighted 加权平均数Average amount of inspection 平均检验数Average and range chart 平均数及全距〔管制〕图Average availability 平均可用度Average deviation (A.D.) (Mean deviation) 平均差Average error (Mean error) 平均误差Average number of defects 平均缺点数Average of ratios 比例平均数Average outgoing quality (AOQ) 平均出厂质量Average outgoing quality curve 平均出厂质量曲线Average outgoing quality level 平均出厂质量水平Average outgoing quality limit (AOQL) 平均出厂水平Average quality level 平均出厂质量界限Average quality level line 质量平均线Average quality protection 平均质量爱护Average range 平均全距Average run length (ARL) 平均连串长度Average sample number (ASN) 平均样品数Average range 平均全距Average run length (ARL) 平均连串长度Average sample number(ASN) 平均样本数Average sample number curve 平均样本曲线Average sample size (ASS) 平均样本大小Average sample size curve 平均样本大小曲线Average sample 平均抽样Average total inspection (ATI) 平均总检验〔件〕数Average total inspection curve 平均总检验数曲线Average value 平均值Avoidable cause 可幸免之缘故Avoidable quality cost 可幸免之质量成本Axiom 公理Axis 轴Axis of abscissa 横轴Axis of ordinate 纵轴BBad lot 坏批Balance frequency 平稳次数Balanced complete type 平稳完备型Balanced design 平稳设计Balanced experiment 平稳实验Balanced incomplete type 平稳不完备型Balanced sample 平稳样本Band chart 带形图Band curve chart 带形曲线图Bank of reliability data 可靠度数据库Bar chart (diagram) 条〔形〕图Bartlett's test 巴特莱特试验Base line 基线Base number 基数Base period 基期Base point 基点Basic reliability 差不多可靠度Batch (Lot) 批Batch of material 材料批Batch process 分批制造方法Batch size 批量Batch testing 批试验Bathtub curve 浴缸曲线Bathtub failure curve 浴缸失效曲线Bayes' estimator 贝式估量式Bayes' theorem 贝式定理Bayesian approach 贝式法Bayesian approcah to design 贝式设计法Bayesian estimation 贝式估量Bead map 标珠图Bell-shaped curve 钟形曲线Bell-shaped distribution 钟形分配〔布〕Bell-shaped failure pattern 钟形失效型态Bell System 贝尔系统Bell Telephone Laboratories 贝尔实验室Bell Telephone Laboratories Sampling Table 贝尔〔实验室〕抽样表Benign failure 无危险的失效Bernoulli distribution 白努利分配〔布〕Best fit 最适配合Best fitting line 最适线Best fitting curve 最适曲线Best linear invariant estimator 最正确线型不变估量式Best linear unbiased estimator 最正确线型不偏估量式Beta coefficient β系数Beta distribution β分配〔布〕Beta function β函数Between-class variance 组间变异数Between-column variance 组间变异Between-column variation 行间变异Between-row variation 列间变异Between sample variation 样本间变异Bias 偏差Bias, downward 向下偏差Bias, downward type 向下型偏差Bias, upward 向上偏差Bias, upward type 向上型偏差Biased error 偏误Biased estimate 偏差估量Biased sample 偏差样本Biased test 偏差试验Bilateral 双边Bill of material (BOM) 物料清单Bimodal 双峰Bimodal curve 双峰曲线Bimodal distribution 双峰分配〔布〕Bimodal redundancy 双峰型复联〔置〕Bimodality 双峰性Binary system 二元制Binomial, skewed 偏态二项Binomial coefficient 二项系数Binomial curve 二项曲线Binomial distribution 二项分配〔布〕Binomial equation 二项方程式Binomial expansion 二项展开式Binomial population 二项群体Binomial probability distribution 二项机率分配〔布〕Binomial probability paper(BIPP) 二项机率纸Binomial series 二项级数Binomial theorem 二项定理Bi-serial 双数列Biserial correlation 双数列相关Biserial coefficient of correlation 双数列相关系数Biserial ratio of correlation 双数列相关比Bivariate 双变量Bivariate distribution 双变量分配〔布〕Bivariate frequency distribution 双变量次数分配〔布〕Bivariate normal distribution 双变量常态分配〔布〕Blend 混,混合Block 量块,〔实验〕区,方块Block design 实验区设计Block diagram 方块图Block factor 地区因素Block in series 串联方块Boundary 界Boundary, cell 组界Bowker-Goode variables plan Bowker-Goode 记量值〔抽样〕打算Bowl drawing 碗珠抽样Bowl experiment 碗珠实验Bowl test 碗珠试验Bowley's coefficient of skewness Bowley偏态系数Bowley's formula Bowley公式Bureau of Ordnance, U.S. Navy 美国海军兵工署Break-even chart 损益平稳图Break-even point (BEP) 损益平稳点Breakthrough 突破British Standards Institution 英国标准协会Broken curve 中断曲线Broken series 中断数列Broken trend 中断趋势Built-in test (BIT) 内含测试,自测Bureau of Commodity Inspection and Quarantine (BCIQ) 商品检验局Bulk sampling Burn-in 大宗抽样Business Process Management (BPM) 业务流程治理Buyer 买方,客户CC chart C〔管制〕图Calculated value (Computed value) 运算值Calculation chart 运算图Calendar time 日历时刻Calibration 校正Calibration record 校正记录Camp-Meidell inequality Camp-Meidell不等式Capability 能力Capability, machine 机器能力Capability, process 制程能力Capability ratio 能力比Capacity 能量,容量Caption 纵标目Carrying out the audit 实施稽核Cartogram 统计图Case method 个案法Catastrophic failure 突然故障,崩坏失效,致命失效Category 类别Cauchy distribution Cauchy 分配〔布〕Causality 因果律Cause 缘故Cause, assignable 非机遇缘故Cause, avoidable 可幸免缘故Cause, chance 机遇缘故Cause, common 共同缘故Cause, findable 可查找缘故Cause, random 随机缘故Cause, special 专门缘故Cause, substantial 本质缘故Cause, unavoidable 不可幸免缘故Cause and effect 因果Cause and effect diagram 特性要因图Cell 组Cell boundary 组界Cell deviation (d) 组离差Cell frequency (f) 组次数Cell interval (i,h) 组距Cell limit 组限Cell method 分组法Cell mid-point (Xm) 组中点Cell value 组值Censored sample 检剔样本Censored test 检剔试验Censorship 检剔Census 普查Center line 中线Central inspection station 中央检验站Central limit theory 趋中理论,中央极限理论Central limit theorem 趋中理论,中央极限理论Central line (CL.) 中心线Central moment 中心动差Central ordinate 中纵坐标Central tendency 集中趋势Central value 中值,中心值Certainty 确定性Certified chart 验证图Certified equipment 合格设备Certified quality engineer (CQE) 合格质量工程师Certified quality technician (CQT) 合格质量技术师Certified reliability engineer (CRE) 合格可靠度工程师Certification 验证Chain model 炼结模型Chain reliability 炼结可靠度Chain sampling plan (CHSP) 炼结抽样打算Chance 机遇Chance cause 机遇缘故Chance error (Probable error) 机遇误差,机误Chance factor 机遇因素Chance failure 机遇故障,机遇失效Chance failure period 机遇失效期Chance fluctuation 机遇波动Chance variable 机遇变数Chance variation 机遇变异Change control 改变〔变更〕治理Chaotic variation 纷乱变异Characteristic 〔质量〕特性Characteristic, qualitative 质的特性Characteristic, quantitative 量的特性Characteristic curve, operating (OC curve) 操作特性曲线,OC曲线Characteristic diagram 特性要因图Characteristic function 特性函数Characteristic life 特性寿命Characteristic operating curve (OC curve) 特性操作曲线〔OC曲线〕Characteristic value 特性值Chargeable failure 可计列失效,故障Charlier check Charlier 覆检法Chart 图,〔管制〕图Chart, acceptance control 验收管制图Chart, average and range 平均数及全距〔管制〕图Chart, average number of defects 平均缺点数〔管制〕图Chart, control 管制图Chart, cumulative sum 累积和〔管制〕图Chart, defects per unit 每单位内缺点数〔管制〕图Chart, fraction defective 不良率〔管制〕图Chart, group 多项〔管制)图Chart, individual 个别值〔管制〕图Chart, median 中位数〔管制〕图Chart, moving and range 移动平均数及全距〔管制〕图Chart, moving range 移动全距〔管制〕图Chart, modified control limits 修正管制界限〔管制〕图Chart, multi-variation 变异值〔管制〕图Chart, multiple 复式〔管制〕图Chart, number defectives 不良〔品〕数〔管制〕图Chart, number of defects 缺点数〔管制〕图Chart, percent defective 不良率管制图Chart, range 全距〔管制〕图Chart, run 操作〔记录〕图Chart, shop 工厂〔管制〕图Chart, Shewhart control Shewhart 管制图Chart, two-way control 双向管制图Chebyshev's inequality Chebyshev 不等式Check inspection 复核检验Check sampling 复核检验员Check inspector 复核抽样,卡方Chi-squareXChi-square distribution分配〔布〕,卡方分配〔布〕X检定,卡方检定Chi-square testX分配〔布〕,卡方分配(布〕Chi-squared distributionXChip 小圆片Chronic defect 慢性缺点Chronological chart 时序图Chronological series 时序数列Class 组Class boundaries (True class limits)组界〔真实组限〕Class form 组形Class frequency (f) 组次数Class interval (i,h) 组距Class limit 组限Class mark 组标,中值Class mean 组平均数Class mid-point(Xm) 组中点Class mid-value 组中值Class of median 组中位数Class value 组值Classes, number of 组数Classification chart 分组,分类Classification frequency 分组次数Classification frequency series 分组次数数列Classification of defectives 不良品分类Classification of defects 缺点分类Classfication of failure 失效分类,故障分类Classification process 分组〔方〕法Clearance 间隙,余隙Cluster 集团Cluster sampling 集团抽样Cochran's test Cochran 检定Code 简化,代号Code letter 代字Coded unit 简化单位Coded value 简化值Coding 简化Coding rule 简化规那么Coefficient 系数Coefficient, correlation 相关系数Coefficient of alienation 余相关系数Coefficient of association 相关系数Coefficient of binomial distribution 二项分配〔布〕系数Coefficient of colligation 束联系数Coefficient of contingency 列联系数Coefficient of correlation 相关系数Coefficient of determination (r2) 定限系数Coefficient of dispersion 离势系数Coefficient of kurtosis 峰度系数Coefficient of multiple correlation 复相关系数Coefficient of net correlation 净相关系数Coefficient of net regression 净回来系数Coefficient of non-determination 不定限系数Coefficient of part correlation 部份相关系数Coefficient of partial correlation 部份相关系数Coefficient of rank correlation 等级相关系数Coefficient of reliability 可靠度系数Coefficient of regression 回来系数Coefficient of skewness 偏态系数,偏斜系数Coefficient of variation (CV) 变异系数Cold standby 冷置系数Collective quality 集体品质Columbia sampling table Columbia 抽样打算Column (Column/Row) 行,纵行〔行/列〕Column head 标目Column diagram 直行图Combination 组合Combinational model 复合模型Combined environmental reliability test (CERT) 复合环境可靠度试验Combined failure 复合失效,复合故障Combined stress life test 复合应力寿命试验Commissioning 委制Commodity 商品Common cause (Chance cause) 共同缘故〔机遇缘故〕Company standard 公司标准Companys need 公司需要Company-wide quality control (CWQC) 全公司质量治理Comparability 可比性Comparable measure 可比量数Compensating error 补偿误差Compensating fluctuation 补偿波动Competing product 竞争产品Complete association 全相联Complete block design 完全区集法Complete confounding 完全交络Complete dissociation 全不相联Complete failure 完全故障,完全失效Completely randomized design 完全随机法Complaint 埋怨Complaint index 埋怨指标Completed product verification 成品验证Component 组件,组件Component bar chart 成份条图Component distiibution 组成份分配〔布〕Component part diagram 成份图Component ratio 成份比Component reliability 组件可靠度Component variance 成份变异数Components of variance 变异数成份Composite curve 复合曲线Composite design 复合法Composite hypothesis 复合假设,组合假设Composite unit 复合单位Compound distribution 复合分配〔布〕Compound event 复合事件Compound probability 复合机率Compounding technique 复合法Compressed limit 压缩界限Compressed limit gauging 压缩界限规那么Computed value 运算值Concentric circle diagram 同心圆图Conception of limit 极限概念Conceptual design 概念设计Conceptual design review 概念设计审查Concession 特采,特认Concomitant factor 共变因素Concomitant variable 共变数Concomitant variation 共变异Concurrency 并行Condition maintenance 状态爱护Condition monitoring 状态监督Condition-based maintenance 状态基准爱护Conditional probability 条件机率Conditions of use 使用条件Confidence 信任,信任Confidence coefficient 信任系数,信任系数Confidence interval 信任区间,信任区间Confidence in test results 试验结果的信任度Confidence level 信任水平,信任水平Confidence limit 信任界限,信任界限Confidence range 信任全距,信任全距Configuration control 型态管制Configuration items 型态件Configuration management 型态治理Confirmation 确认Conformance to the requirement 符合要求Conformation 一致Conforming article 合格品Conformity 符合Confounding 交络Confounding, complete 完全交络Confounding, partial 部份交络Connector 连接器Consignment 托付,寄售Consistency 一致性Constancy 恒久性Constancy of great numbers 大数恒久性Constant 常数Constant cause system 恒常缘故系统Constant error 恒常误差Constant failure period 恒常失效期Constant failure rate dustribution 恒常失效率分配〔布〕Constant weight (Fixed weight) 固定权数Constraint 束缚Consultant 治理顾问师Consumer 消费者Consumer acceptance specification 消费者允收规格Consumerism 消费者主义Consumer's risk (CR) 消费者冒险率Consumer test panel 消费者试验小组Consumer preference 消费者偏好Consumer sensitivity test 消费者感官试验Contingency 列联Contingency coefficient 列联系数Contingency table 列联表Contingency theorem 列联理论Continuity correction 连续校正Continuous change 连续变更Continuous data 连续数据Continuous distribution 连续分配〔布〕Continuous production 连续生产Continuous sampling 连续抽样Continuous sampling plan (CSP) 连续抽样打算Continuous series 连续数列Continuous variable 连续变量Contract 合约Contract preparation 拟定合约Contract review 合约检讨Contract requirements 合约需求Contract requirements analysis 合约需求分析Contractors 合约商Contrast analysis 对比分析Control, in 在管制〔状态〕下Control, lack of 缺乏管制Control, out of 超出管制Control, state of 管制状态Control, under 在管制〔状态〕下Control chart 管制图Control chart, cumulative sum 累积和管制图Control chart, defects per unit 每单位内缺点数管制图Control chart, two-way 双向管制图Control chart factor 管制图系数Control chart for attribute 计数值管制图Control chart for variable (measurement) 计量值管制图Control chart method 管制图法Control chart pattern 管制图类型Control factor 管制因素Control gaging (gauging) 管制规测Control level 管制水平Control limit 管制界限Control limit, lower 管制下限Control limit, modified 修正管制界限Control limit, upper 管制上限Control limit factor 管制界限因子Control line 管制线Control of measuring and test equipment 量测与试验设备之管制Control of nonconforming material 不合格物料之管制Control of nonconforming product 不合格产品之管制Control of production 生产管制Control of reliability 可靠度管制Control of verification status 验证状况之管制Control plan 管制打算Control point 管制点Control station 管制站Control system 管制系统Controllability 可管制性Controlled process 管制制程Controlled state 管制状态Controlled variability 管制变异性Controlled variable 管制变数Controlling item 管制项目Convenience lot 合宜的批Convergence 收敛Cooked distribution 中断分配〔布〕Coordinate 坐标Coordinate axis 坐标轴Coordinate line 坐标线Coordination 和谐Coordination for reliability 可靠度和谐Correction 校正,修正Correction, Sheppard Sheppard 校正数Correction factor 修正因子Correction for continuity 连续校正Correction for mean 平均数校正Correction term 校正项Corrective action 矫正行动,改正措施Corrective maintenance 矫正爱护,改正爱护Corrective maintenance time 矫正爱护时刻,改正爱护时刻Corrective sorting 修正选别Correlated measure 相关量数Correlated samples 相关样本Correlation 相关Correlation, coefficient of 相关系数Correlation, direct 直截了当相关Correlation, index of 相关指数Correlation, inverse 反相关Correlation, multiple 复相关Correlation, negative 负相关Correlation, net 净相关Correlation, nonlinear 非线性相关Correlation, nonsense 无意义相关Correlation, part 部份相关,偏相关Correlation, partial 部份相关,偏相关Correlation, perfect 完全相关Correlation, rank 等级相关Correlation, serial 数序相关Correlation, simple 简相关Correlation, zero 零相关Correlation analysis 相关分析Correlation chart 相关图Correlation, coefficient 相关系数Correlation coefficient, rank 等级相关系数Correlation matrix 相关矩阵Correlation of attributes 品性相关Correlation ratio 相关比Correlation of x on y x与y的相关比Correlation ratio of y on x y与x的相关比Correlation scatter chart 相关散布图Correlation surface 相关面Correlation table 相关表Correlation theory 相关理论Correlogram 相关图Corrosive atmosphere 腐蚀性空气Cost 成本,费用Cost, acquisition 取得成本Cost, appraisal 评估〔鉴定〕成本Cost, external failure 外部失败成本Cost, internal failure 内部失败成本Cost, life cycle 寿命周期成本Cost, logistic 后续成本Cost, prevention 预防成本Cost, quality 质量成本Cost, quality control 质量治理成本Cost, rework 重加工成本Cost effectiveness 成本效益Cost function 成本机能Cost model for reliability optimization 可靠度最正确化成本模式Cost reduction 成本减低Count (Countable) data 点计数据Counter variation 反行变异Co-variation 共变异Covariance 共变异数,共变数Covariance analysis 共变异数分析Covariance matrix 共变异矩阵Craps, game of 掷骰游戏Credibility 信用Creep failure 潜变失效,潜变故障Crest 峰Criteria for workmanship 工作技艺准那么Criterion 准那么,规范Criterion, acceptance 验收准那么〔规范〕Critical component control 重要组件管制Critical defect 严峻缺点Critical defective 严峻不良品Critical design review 关键设计审查Critical failure 关键故障,严峻失效Critical items 关键品目,重要件Critical path 要径Critical path analysis 要径分析法Critical region 临界区域,弃却区域,判定区Critical value 临界值,判定值Criticality 严峻性,关键性Cross 交叉Cross check 互校Cross classification 交叉分类Cross correlation 交叉相关Cross formula 交互公式Cross-hatch 交叉线Cross-hatched map 交叉图Cross-over design 交叉打算Crossed design 交叉法Crude mode 概括众数Crude moment 概括动差Cubic chart (diagram) 立方图Culled 检选Cumulant 累积数Cumulation, downward 向下累积Cumulation, total 全部累积Cumulation, upward 向上累积Cumulation average chart 累积平均数〔管制〕图Cumulative curve 累积曲线Cumulative curve chart 累积曲线图Cumulative damage 累积损坏Cumulative distribution (Ogive) 累积分配〔布〕Cumulative distribution function 累积分配〔布〕函数Cumulative error 累积误差Cumulative failure frequency 累积故障次数,累积失效次数Cumulative frequency 累积次数Cumulative frequency arrangement 累积次数排列Cumulative frequency curve 累积次数曲线Cumulative frequency 累积次数曲线图Cumulative frequency distribution 累积次数分配〔布〕Cumulative frequency polygon 累积〔次数〕多边形Cumulative frequency (probability) function 累积次数〔机率〕函数Cumulative frequency table 累积次数表Cumulative function 累积函数Cumulative graph 累积图Cumulative hazard function 累积冒险函数Cumulative mean 累积平均数Cumulative normal distribution 累积常态分配Cumulative number of failures 累积失效数,累积故障数Cumulative percentage of failures 累积失效百分率,累积故障百分率Cumulative probability distribution 累积机率分配〔布〕Cumulative sum 累积和Cumulative sum chart 累积和〔管制〕图Cumulative sum control chart 累积和管制图Cumulative terms 累积项Curtailed (Truncated) inspection 截略检验Curtailed (Truncated) sample inspection截略样品检验Curtailed sampling 截略抽样Curtailed sampling inspection 截略抽样检验Curtaijed sampling plan 截略抽样打算Curtailment of sampling plan 抽样打算之截略Curve 曲线Curve, frequency 次数曲线Curve, normal 常态曲线Curve chart (diagram) 曲线图Curve fitting 曲线配合Curve of error 误差曲线Curve of means 平均数曲线Curve of probability 机率曲线Curve type criterion 曲线型准那么Curve shape 曲线形状Curvilinear correlation 曲线相关Curvilinear regression 曲线回来Curvilinear trend 曲线趋势Curvilinearity 曲线性Customer 客户,顾客Customer complaint 顾客埋怨Customer feedback information 顾客回馈信息Customer incurred cost 顾客引发成本Customer operation cost 顾客作业成本Customer repair cost 顾客修理成本Customer requirement 顾客要求Customer satisfaction 顾客中意度Customer's need 顾客需要Cusum chart 累积和〔管制〕图Cycles 周期Cycles between failures 失效间隔周期,故障间隔周期Cycle of operation 操作周期Cyclic curve 周期〔循环〕曲线Cyclic damage 周期性损坏Cyclic load 周期性负荷Cyclical deviation 周期〔循环〕离差Cyclical fluctuation 周期波动Cyclical trend 周期趋势Cyclical movement 周期移动Cyclical variation 周期变异Cycling failure rate 周期性失效率,周期性故障率DD chart d管制图Data 数据Data analysis 数据分析Data bank 资料室〔库〕Data exchange program 数据交换打算Data, inspection 检验数据Data item 数据项,文件项目Data processing 数据处理Death rate 死亡率Debug (debugging) 除错Decile 十分位数Decimal fraction 小数Decision function 决策函数Decision line 决定线Decision making 决策Decision variable 决策变数Decreasing failure rate distribution 递减失效率分配(布〕Decrement 减量Decrement rate 减率Defect 疵病,缺点Defect, chronic 慢性缺点Defect, critical 严峻缺点Defect, incidental 偶发缺点Defect, major 要紧缺点Defect, minor 次要缺点Defect, sporadic 突发缺点Defect and failure analysis 缺点与失效分析Defect chart 缺点数〔管制〕图Defect Free 零缺点Defect prevention 缺点预防Defects, number of 缺点数Defects classification 缺点分类Defects per hundred units (dphu) 百件缺点数Defects per unit chart 每单位〔内〕缺点数〔管制〕图Defects per unit plan 每单位〔内〕缺点数〔管制〕打算Defective 不良品Defective, fraction 不良率Defective chart 不良品数〔管制〕图Defective material 不良材料Defective number 不良品数Defective part 不良零件Defective parts, percentage of 不良零件百分率Defective prevention 不良品预防Defective unit 不良品〔单位〕Defectives, number of 不良〔品〕数Defectives classification 不良品分类Definition(s) 定义Deflated series 调剂数列Deflated value 调剂值Deflating index 调剂指数Degradation 劣化Degradation failure 劣化故障,劣化失效Degree of accuracy 准确度Degree of approximation 近似度Degree of association 相联度Degree of confidence 信任〔赖〕度Degree of contribution 奉献度Degree of freedom (DF) 自由度Degree of reliability 可靠度Delivery 交货,出厂Delivery inspection 出厂检验Delivery qulaity 出厂品质Delivery time 运送时刻Demerit 减点Demerit chart 减点〔数〕〔管制〕图Demerit rating 减点评比Demerits per unit 每单位〔内〕减点数Demonstration 示范,验证,展现Demonstration test 验证试验,展现试验Density function 密度函数Dependability 可恃性,相依性,依靠性Dependent factor 因变因子Dependent failure 相依失效,相依故障Dependent variable 因变数Derating 降等,额降,减额定Derivation 导出Derived table 导出表Descriptive item 说明项Descriptive statistics 记述统计〔学〕Design 设计Design baseline 设计准那么Design change 设计变更Design considerations 设计考虑Design control 设计管制Design change control 设计变更管制Design control, new 新设计管制Design criterion 设计准那么Design disclosure package 设计启导文件Design effect cost 设计效应成本Design freeze 设计冻结Design in 设计到里面去Design input 设计输入Design matrix 设计矩阵Design output 设计输出Design of experiment 实验打算Design planning 设计规画Design profile 设计轮廓Design proving 设计认可Design qualification 设计之合格性Design release 设计公布Design requalification 设计合格之再认定Design review 设计审查Design specification 设计规格Design validation 设计确认Design verification 设计验证,查证Design verification test 设计验证试验Designation 名称Designed experiment 实验打算Destructive inspection (test) 破坏性检验〔试验〕Detailed design 细部设计Detailed design review 细部设计审查Detailed inspection (100% inspection) 全数检验〔百分之百检验〕Detect 侦测Detection of a failure unit 失效单位之检测,故障单位之检测Detection time 检测时刻Deterioration 衰变,劣化Determination, coefficient of 定限系数Development 进展Development test 进展试验Deviation 离差Deviation, average 平均差Deviation, mean 平均差Deviation, root-mean-square 均方根差Deviation, sample standard 样本标准差Deviation, standard 标准差Deviation, universe standard 群体标准差。

质量英文单词

质量英文单词

部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点(CR)MAJOR DEFECT:主要缺点(MA)MINOR DEFECT:次要缺点(MI)MAX:Maximum最大值MIN:Minimum最小值Subject matter:主要事项Auditor:审核员BOM:Bill of material物料清单Rework:重工ID:identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR:First Piece Inspection Report首件检查报告FAA:首件确认SPC:统计制程管制DPPM: Defect Part Per Million(不良率的一种表达方式:百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC:允收REJ:拒收S/S:Sample size抽样检验样本大小SI-SIV:Special I-Special IV特殊抽样水平等级ISO:国际标准化组织ISA:Industry Standard Architecture工业标准体制结构PDCA:管理循环MRB:Material reject bill退货单JIT:just in time(即时管理)5S:seiri seiton seiso seiketsu shitsuke(整理,整顿,清扫,清洁,修养)SOP:standard operation process(标准作业程序)SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction(作业指导书)FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告QIP:Quality Improvement Plan品质改善计划CIP:Continual Improvement Plan持续改善计划来料品质回馈单)SCAR: Supplier Corrective Action Report (供货商改善对策报告) 8D Sheet: 8 Disciplines sheet ( 8D单)PDCA:PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量) DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (品质工程表) DRP :运销资源计划 (Distribution Resource Planning)ODM :委托设计与制造 (Original Design & Manufacture) OLAP:线上分析处理 (On-Line Analytical Processing) OLTP:线上交易处理 (On-Line Transaction Processing) OPT :最佳生产技术 (Optimized Production Technology) PDCA:PDCA管理循环 (Plan-Do-Check-Action)PDM:产品数据管理系统 (Product Data Management)) RCCP:粗略产能规划 (Rough Cut Capacity Planning) SCM :供应链管理 (Supply Chain Management) SFC :现场控制 (Shop Floor Control)TOC:限制理论 (Theory of Constraints)LRR:Lot Rejeet Rate批退率ATIN:Attention知会5W1H:When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money ,Information人力,机器,材料,方法, 市场,管理,资金,资讯Area待检区。

质量词汇

质量词汇

质量体系词汇质量 quality等级 grade质量环 quality loop质量螺旋quality spiral质量方针quality policy质量管理quality management质量保证quality assurance质量控制 quality control质量体系quality system质量计划quality plan质量审核quality audit质量监督quality surveillance质量体系评审quality system review设计评审 design review检验 inspection可追溯性 traceability超差特许 concession waiver偏离许可 production permit ;deviation permit可靠性 reliability产品责任;服务责任 product liability;service liability 不合格(不符合项) nonconformity缺陷 defect规范 specification实体 entity ;item过程 process程序 procedure产品 product服务 service提供服务 service delivery单位 organization组织结构 organization structure顾客 cutomer供方 supplier需方 purchaser承包方 contractor质量要求requirement for quality社会要求requirememt of society可信性dependability相容性compatibility互换性interchangeability安全性safety合格conformity鉴定过程qualification process鉴定合格qualified自检self-inspection验证verification确认validation客观证据objective evidence质量方针quality policy质量管理quality management质量策划quality planning质量控制quality control质量保证quality assurance质量体系quality system全面质量管理total qualitymanagement质量改进quality improvement管理评审managemen review合同评审contract review设计评审design review质量手册quality manual质量环quality loop质量成本quality-related costs质量损失 quality losses质量保证模式model for quality assurance 证实程度degree of demonstration质量评价quality evaluation质量监督quality surveillance停止点hold point质量审核quality audit质量审核观察结果quality audit observation 质量审核员quality auditor受审核方auditee预防措施preventive action纠正措施corrective action不合格品处置disposition of nonconformity 返修repair返工rework。

QC常用单词-中英对照

QC常用单词-中英对照

QC常用单词-中英对照介绍这篇文档是为了方便质量控制人员〔Quality Control, QC〕在工作中使用而编写的。

在质量控制的过程中,我们经常会遇到一些常用的单词,这些单词在中英文之间的对照对我们的工作非常有帮助。

本文档将列出一些常用的QC单词,并提供它们的中英对照,希望能对大家有所帮助。

QC常用单词列表及对照下面是一些常用的QC单词及其中英对照:1.产品〔Product〕2.测试〔Test〕3.缺陷〔Defect〕4.报告〔Report〕5.标准〔Specification〕6.标准〔Standard〕7.检查〔Check〕8.方案〔Plan〕9.测试用例〔Test Case〕10.可靠性〔Reliability〕11.准确性〔Accuracy〕12.效率〔Efficiency〕13.可用性〔Usability〕14.可维护性〔Maintainability〕15.平安性〔Security〕16.可重复性〔Repeatability〕17.测试数据〔Test Data〕18.异常〔Exception〕19.验证〔Validation〕20.验收〔Acceptance〕除了以上列出的单词,还有很多其他的单词也非常常用,希望大家在实际工作中能遇到更多的常用单词,并对它们的中英对照有更多的了解。

总结质量控制是软件开发过程中非常重要的一个环节,QC人员需要掌握一些专业的术语和常用单词。

本文档提供了一些常用的QC单词及其中英对照,希望对大家在工作中有所帮助。

同时也希望大家能不断学习和积累,提高自己的专业水平。

如果在实际工作中遇到了其他常用单词,也可以将它们添加到这个列表中,以便与大家共享。

谢谢大家阅读本文档!参考资料无。

常用质量术语中英文对照表

常用质量术语中英文对照表
Stratification层别法
5W2H:what做什么?有必要吗?Why为什么要做?目的在哪
里?where哪里做?没有更合适的地方吗?When何时做?时间 是否合适?Who谁做?有没有更合适的人?
How如何做?有没有更好的方 法?how much需要的成本如何?
4M1E:manpower人员method方法machine机器material物料
规格下限
UCL (Up Control Line)
控制上限
LCL (Low Control Line)
控制下限
CL (Control Line)
控制线
SQA (Source (supplier) Quality Assurance)
供应商品质保证
TQM仃otal Quality Management)
常用质量术语中英文对照表
AC(Acceptability Criteria)
验收标准
ANOVA
方差分析
AQL (Acceptable Quality Level)
可接受质量水平
APQP (Advaneed Product Quality Planning and Control Plan)
产品质量先期策划和控制计划
关键质量特性
DOE (Design of Experiment)
试验设计
ECN(Engin eeri ng Cha nge Notice)
工程变更通知书
EMS (En vir onment Man ageme nt System)
环境管理体系
Feasibility Report
可行性报告
FIFO (First In First Out)

质量英语词汇大全(中英对照)(DOC 122页)

质量英语词汇大全(中英对照)(DOC 122页)

质量英语词汇大全(中英對照)(DOC 122页)品质名词(中英对照)AABC analysis ABC 分析Abnormality 不正常性Abscissa 横坐标Absolute deviation 绝对离差Absolute dispersion 绝对离势Absolute error 绝对误差Absolute frequency 绝对次数Absolute number 绝对数Absolute reliability 绝对可靠度Absolute term 绝对项Absolute value 绝对值Absolute variation 绝对变异Abstract number 抽象数Abstract unit 抽象单位Accelerated factor 加速系数,加速因子Accelerated life test 加速寿命试验Accelerated test 加速试验Acceleration 加速度Acceptable limit 允收界限Acceptable process 允收制程水平Acceptable quality 允收品质Acceptable quality level (AQL) 允收质量水平Acceptable reliability level (ARL) 允收可靠度水平Acceptability 允收性Acceptability criterion 允收标准Acceptance 允收,验收Acceptance, probability of 允收机率Acceptance, region of 允收区域Acceptance and rejection criteria 允收与拒收准则Acceptance boundary 允收界限Acceptance coefficient 允收系数Acceptance control chart 验收管制图Acceptance cost 验收费用Acceptance criteria 允收准则Acceptance error 允收误差Acceptance inspection 验收检验Acceptance limit 允收界限Acceptance line 允收线Acceptance number 允收(不良品)数Acceptance plan 验收计划Acceptance procedure 验收程序Acceptance/rectification scheme 允收/精选方案Acceptance sampling, attribute 计数值验收抽样Acceptance sampling, variable 计量值验收抽样Acceptance sampling plan 验收抽样计划Acceptance sampling scheme 验收抽样方案Acceptance test 验收试验Acceptance value 允收值Acceptance zone 允收区域Acceptance product 允收品Accepting lot 允收批Access time 接近时间,故障诊断时间Accessibility 可接近性Accident rate 意外率Accidental error 偶误,偶然误差Accidental fluctuation 偶然波动Accidental movement 意外移动Accounting test 验算(决算)试验Accumulated operating time 累积操作时间Accuracy 准确度Accuracy of data 数据准确度Accuracy of estimation 估计准确度Accuracy of the mean 平均数准确度Achieved availability 实际可用度Action 行动,措施Action, corrective 矫正行动(措施)Action control chart 行动管制图Action limit 行动界限Active line 行动线Active maintenance time 实际维护时间Active parallel redundancy 主动并复联(置)Active preventive maintenance 现行预防维护时间Active redundancy 主动复联(置)Active repair time 实际修复时间Active standby 主动备用Active time 运用时间Actual frequency 实际次数Actual limit 实际界限Actual range 实际全距Actual value 实际值Adaptability 可适应性Adaptive control 修改管制Addition theorem 加法定理Additivity 加法性,可加性Adjusted average 修正平均数Adjusted value 修正值Adjustment factor 调整系数Administration time for a repair 修复之管理时间Administrative time 管理时间Adopted value 采用值Advisory Group on Reliability of Electronic Equipment (AGREE) 电子装备可靠度顾问团Aeronautical Radio, Incorporated (ARINC) 航空无线电公司After-sales service 售后服务Age 年限Age at death 死亡年限Age at failure 失效年限Age-based maintenance 年限基准维护Aggregative method 综合法Aging 老化Agreement of quality assurance 质量保证之协议Agreement on verification method 验(查)证方法之协议Alarm signals 警告(报)讯号Alert time 待命时间Algebraic sum 代数和Algorism (Algorithm) 阿拉伯数字计数法Alias 假名Alienation 余相关Alignment chart 列线图Allocation 配当Allocation of reliability 可靠度配当Allowable percent defective (Acceptable quality level, AQL) 允收不良率(允收质量水平)Allowance 允差,裕度Alternative hypothesis 对立假设American Management Association (AMA) 美国管理协会American National Standards Institute (ANSI) 美国标准协会American Society for Quality Control (ASQC) 美国质量管理学会American Society for Mechanical Engineers (ASME) 美国机械工程师学会American Society for Testing and Materials (ASTM) 美国材料试验学会American Standard Association (ASA) 美国标准协会American Statistical Association (ASA) 美国统计协会American War Standards (AWS) 美国战时标准Ambient condition 周遭条件Analysis, sequential 逐次分析Analysis by accumulated frequency 累积法,累积次数分析Analysis by non-accumulated frequency 次数法,非累积次数分析Analysis of correlation 相关分析Analysis of covariance 共变异数分析Analysis of means (AVON) 平均数分析Analysis of problem 问题之分析Analysis of variance (ANOVA) 变异数分析Analysis sample 分析样本Analytical error 分析误差Angular transformation 角度转(变)换Anti-logarithm 逆对数Anti-mode 逆众数AOQL Sampling Table 平均出厂质量界限抽样数Applicability 应用性Applied statistics 应用统计学Apportionment of reliability 可靠度配当Apportionment techniques 配当技术Appraisal cost 鉴定成本,评估成本Appraisal system 评估制度Appraisal of quality 质量评估Approach to sequential testing 逐次试验法Approval of processes and equipment 核准制程与设备Approximate mode 近似众数Approximate number 近似数值Approximation 近似法,概算AQL (Acceptable quality level) 允收(质量)水平Arbitrary average (Assumed average,Arbitrary mean) 假定平均数Arbitrary origin 假定原点Arbitrary scale 假定标度Area bar chart 面积条图Area chart (diagram, graph) 面积图Area sampling 地区抽样Arithmetic average 算术平均数Arithmetic cross 算术交叉Arithmetic graph 算术图Arithmetic line chart 算术线图Arithmetic mean 算术平均数Arithmetic paper 算术纸Arithmetic probability paper 算术机率纸Arithmetic progression (Arithmetic series) 算术级数,等差级数Arithmetic scale 算术标度,等差标度Arithmetic series 算术级数,等差级数Army Ordnance Table 陆军兵工署(抽样)表Army Service Forces Table 陆军(抽样)表序列Array 序列Array distribution 序列分配(布)Array of data 数据序列Assemble 装配(组立)Assembled product 装配品Assembly 装配件Assembly inspection 装配检验Assembly quality analysis report 装配质量分析报告Assessed failure rate 评估失效率Assessed mean active -maintenance time 评估时间现行维护时间Assessed mean life 评估平均寿命Assessed mean time between failures 评估平均失效间格时间Assessed mean time to failure 评估平均失效前时间Assessed reliability 评估可靠度Assessed value 评估值Assessment of subcontractor 分包商之评鉴Assignable cause (Special cause) 非机遇原因(特殊原因)Assignable variation 非机遇变异Associated dependent variable 相联因变数Associated variate 相联变量Association coefficient 相联系数Association of attribute 品性相联Association table 相联表,联合表Assumed mean (Assumed average,Arbitrary average) 假定平均数Assumed median 假定中位数Assumed origin 假定原点Assurance quality 保证质量Assurance function 保证功能Asymmetrical distribution不对称分配(布)Asymmetry 不对称Asymptotic distribution 趋近分配(布)At random 随机Attribute 计数值,属性Attribute classification 品性分类Attribute data 计数数据Attribute inspection 计数值检验Attribute sampling 计数值抽样Attribute sampling plan 计数值抽样计划Attribute testing (Go no-go testing) 计数值试验(通过与不通过试验)Attribute value 计数值Audit 稽核Audit for reliability 可靠度稽核Audit of decision 稽核决策Audit plan 稽核计划Audit report 稽核报告Auditing report 稽核报告Auto-correlation 自动相关Automatic switch-over redundancy 自动切换复联(置)Automatic test equipment (Am) 自动试验装备Auto-regression 自动回归Availability 可用性,可用度Average (Mean) 平均数,平均值Average, grand 总平均Average, moving 移动平均数Average, sample 样本平均数Average, standard error of 标准误平均数Average, universe 群体平均数Average, weighted 加权平均数Average amount of inspection 平均检验数Average and range chart 平均数及全距(管制)图Average availability 平均可用度Average deviation (A.D.) (Mean deviation) 平均差Average error (Mean error) 平均误差Average number of defects 平均缺点数Average of ratios 比例平均数Average outgoing quality (AOQ) 平均出厂质量Average outgoing quality curve 平均出厂质量曲线Average outgoing quality level 平均出厂质量水平Average outgoing quality limit (AOQL) 平均出厂水平Average quality level 平均出厂质量界限Average quality level line 质量平均线Average quality protection 平均质量保护Average range 平均全距Average run length (ARL) 平均连串长度Average sample number (ASN) 平均样品数Average range 平均全距Average run length (ARL)平均连串长度Average sample number(ASN) 平均样本数Average sample number curve 平均样本曲线Average sample size (ASS) 平均样本大小Average sample size curve 平均样本大小曲线Average sample 平均抽样Average total inspection (ATI) 平均总检验(件)数Average total inspection curve 平均总检验数曲线Average value 平均值Avoidable cause 可避免之原因Avoidable quality cost 可避免之质量成本Axiom 公理Axis 轴Axis of abscissa 横轴Axis of ordinate 纵轴BBad lot 坏批Balance frequency 平衡次数Balanced complete type 平衡完备型Balanced design 平衡设计Balanced experiment 平衡实验Balanced incomplete type 平衡不完备型Balanced sample 平衡样本Band chart 带形图Band curve chart 带形曲线图Bank of reliability data 可靠度数据库Bar chart (diagram) 条(形)图Bartlett's test 巴特莱特试验Base line 基线Base number 基数Base period 基期Base point 基点Basic reliability 基本可靠度Batch (Lot) 批Batch of material 材料批Batch process 分批制造方法Batch size 批量Batch testing 批试验Bathtub curve 浴缸曲线Bathtub failure curve 浴缸失效曲线Bayes' estimator 贝式估计式Bayes' theorem 贝式定理Bayesian approach 贝式法Bayesian approcah to design 贝式设计法Bayesian estimation 贝式估计Bead map 标珠图Bell-shaped curve 钟形曲线Bell-shaped distribution 钟形分配(布)Bell-shaped failure pattern 钟形失效型态JBell System 贝尔系统Bell Telephone Laboratories 贝尔电话实验室Bell Telephone Laboratories Sampling Table 贝尔(电话实验室)抽样表Benign failure 无危险的失效Bernoulli distribution 白努利分配(布)Best fit 最适配合Best fitting line 最适线Best fitting curve 最适曲线Best linear invariant estimator 最佳线型不变估计式Best linear unbiased estimator 最佳线型不偏估计式Beta coefficient β系数Beta distribution β分配(布)Beta function β函数Between-class variance 组间变异数Between-column variance 组间变异Between-column variation 行间变异Between-row variation 列间变异Between sample variation 样本间变异Bias 偏差Bias, downward 向下偏差Bias, downward type 向下型偏差Bias, upward 向上偏差Bias, upward type 向上型偏差Biased error 偏误Biased estimate 偏差估计Biased sample 偏差样本Biased test 偏差试验Bilateral 双边Bill of material (BOM) 物料清单Bimodal 双峰Bimodal curve 双峰曲线Bimodal distribution 双峰分配(布)Bimodal redundancy 双峰型复联(置)Bimodality 双峰性Binary system 二元制Binomial, skewed 偏态二项Binomial coefficient 二项系数Binomial curve 二项曲线Binomial distribution 二项分配(布)Binomial equation 二项方程式Binomial expansion 二项展开式Binomial population 二项群体Binomial probability distribution 二项机率分配(布)Binomial probability paper(BIPP) 二项机率纸Binomial series 二项级数Binomial theorem 二项定理Bi-serial 双数列Biserial correlation 双数列相关Biserial coefficient of correlation 双数列相关系数Biserial ratio of correlation 双数列相关比Bivariate 双变量Bivariate distribution 双变量分配(布)Bivariate frequency distribution 双变量次数分配(布)Bivariate normal distribution 双变量常态分配(布)Blend 混,混合Block 量块,(实验)区,方块Block design 实验区设计Block diagram 方块图Block factor 地区因素Block in series 串联方块Boundary 界Boundary, cell 组界Bowker-Goode variables plan Bowker-Goode 记量值(抽样)计划Bowl drawing 碗珠抽样Bowl experiment 碗珠实验Bowl test 碗珠试验Bowley's coefficient of skewness Bowley偏态系数Bowley's formula Bowley公式Bureau of Ordnance, U.S. Navy 美国海军兵工署Break-even chart 损益平衡图Break-even point (BEP) 损益平衡点Breakthrough 突破British Standards Institution 英国标准协会Broken curve 中断曲线Broken series 中断数列Broken trend 中断趋势Built-in test (BIT) 内含测试,自测Bureau of Commodity Inspection and Quarantine (BCIQ) 商品检验局Bulk sampling Burn-in 大宗抽样Business Process Management (BPM) 业务流程管理Buyer 买方,客户CC chart C(管制)图Calculated value (Computed value) 计算值Calculation chart 计算图Calendar time 日历时间Calibration 校正Calibration record 校正记录Camp-Meidell inequality Camp-Meidell不等式Capability 能力Capability, machine 机器能力Capability, process 制程能力Capability ratio 能力比Capacity 能量,容量Caption 纵标目Carrying out the audit 实施稽核Cartogram 统计图Case method 个案法Catastrophic failure 突然故障,崩坏失效,致命失效Category 类别Cauchy distribution Cauchy 分配(布)Causality 因果律Cause 原因Cause, assignable 非机遇原因Cause, avoidable 可避免原因Cause, chance 机遇原因Cause, common 共同原因Cause, findable 可寻找原因Cause, random 随机原因Cause, special 特殊原因Cause, substantial 本质原因Cause, unavoidable 不可避免原因Cause and effect 因果Cause and effect diagram 特性要因图Cell 组Cell boundary 组界Cell deviation (d) 组离差Cell frequency (f) 组次数Cell interval (i,h) 组距Cell limit 组限Cell method 分组法Cell mid-point (Xm) 组中点Cell value 组值Censored sample 检剔样本Censored test 检剔试验Censorship 检剔Census 普查Center line 中线Central inspection station 中央检验站Central limit theory 趋中理论,中央极限理论Central limit theorem 趋中理论,中央极限理论Central line (CL.) 中心线Central moment 中心动差Central ordinate 中纵坐标Central tendency 集中趋势Central value 中值,中心值Certainty 确定性Certified chart 验证图Certified equipment 合格设备Certified quality engineer (CQE) 合格质量工程师Certified quality technician (CQT) 合格质量技术师Certified reliability engineer (CRE) 合格可靠度工程师Certification 验证Chain model 炼结模型Chain reliability 炼结可靠度Chain sampling plan (CHSP) 炼结抽样计划Chance 机遇Chance cause 机遇原因Chance error (Probable error) 机遇误差,机误Chance factor 机遇因素Chance failure 机遇故障,机遇失效Chance failure period 机遇失效期Chance fluctuation 机遇波动Chance variable 机遇变数Chance variation 机遇变异Change control 改变(变更)管理Chaotic variation 混乱变异Characteristic (质量)特性Characteristic, qualitative 质的特性Characteristic, quantitative 量的特性Characteristic curve, operating (OC curve) 操作特性曲线,OC曲线Characteristic diagram 特性要因图Characteristic function 特性函数Characteristic life 特性寿命Characteristic operating curve (OC curve) 特性操作曲线(OC曲线)Characteristic value 特性值Chargeable failure 可计列失效,故障Charlier check Charlier 覆检法Chart 图,(管制)图Chart, acceptance control 验收管制图Chart, average and range 平均数及全距(管制)图Chart, average number of defects 平均缺点数(管制)图Chart, control 管制图Chart, cumulative sum 累积和(管制)图Chart, defects per unit 每单位内缺点数(管制)图Chart, fraction defective 不良率(管制)图Chart, group 多项(管制)图Chart, individual 个别值(管制)图Chart, median 中位数(管制)图Chart, moving and range 移动平均数及全距(管制)图Chart, moving range 移动全距(管制)图Chart, modified control limits 修正管制界限(管制)图Chart, multi-variation 变异值(管制)图Chart, multiple 复式(管制)图Chart, number defectives 不良(品)数(管制)图Chart, number of defects 缺点数(管制)图Chart, percent defective 不良率管制图Chart, range 全距(管制)图Chart, run 操作(记录)图Chart, shop 工厂(管制)图Chart, Shewhart control Shewhart 管制图Chart, two-way control 双向管制图Chebyshev's inequality Chebyshev 不等式Check inspection 复核检验Check sampling 复核检验员Check inspector 复核抽样Chi-square ,卡方Chi-square distribution 分配(布),卡方分配(布)Chi-square test 检定,卡方检定Chi-squared distribution 分配(布),卡方分配(布)Chip 小圆片Chronic defect 慢性缺点Chronological chart 时序图Chronological series 时序数列Class 组Class boundaries (True class limits)组界(真实组限)Class form 组形Class frequency (f) 组次数Class interval (i,h) 组距Class limit 组限Class mark 组标,中值Class mean 组平均数Class mid-point(Xm) 组中点Class mid-value 组中值Class of median 组中位数Class value 组值Classes, number of 组数Classification chart 分组,分类Classification frequency 分组次数Classification frequency series 分组次数数列Classification of defectives 不良品分类Classification of defects 缺点分类Classfication of failure 失效分类,故障分类Classification process 分组(方)法Clearance 间隙,余隙Cluster 集团Cluster sampling 集团抽样Cochran's test Cochran 检定Code 简化,代号Code letter 代字Coded unit 简化单位Coded value 简化值Coding 简化Coding rule 简化规则Coefficient 系数Coefficient, correlation 相关系数Coefficient of alienation 余相关系数Coefficient of association 相关系数Coefficient of binomial distribution 二项分配(布)系数Coefficient of colligation 束联系数Coefficient of contingency 列联系数Coefficient of correlation 相关系数Coefficient of determination (r2) 定限系数Coefficient of dispersion 离势系数Coefficient of kurtosis 峰度系数Coefficient of multiple correlation 复相关系数Coefficient of net correlation 净相关系数Coefficient of net regression 净回归系数Coefficient of non-determination 不定限系数Coefficient of part correlation 部份相关系数Coefficient of partial correlation 部份相关系数Coefficient of rank correlation 等级相关系数Coefficient of reliability 可靠度系数Coefficient of regression 回归系数Coefficient of skewness 偏态系数,偏斜系数Coefficient of variation (CV) 变异系数Cold standby 冷置系数Collective quality 集体品质Columbia sampling table Columbia 抽样计划Column (Column/Row) 行,纵行(行/列)Column head 标目Column diagram 直行图Combination 组合Combinational model 复合模型Combined environmental reliability test (CERT) 复合环境可靠度试验Combined failure 复合失效,复合故障Combined stress life test 复合应力寿命试验Commissioning 委制Commodity 商品Common cause (Chance cause) 共同原因(机遇原因)Company standard 公司标准Companys need 公司需要Company-wide quality control (CWQC) 全公司质量管理Comparability 可比性Comparable measure 可比量数Compensating error 补偿误差Compensating fluctuation 补偿波动Competing product 竞争产品Complete association 全相联Complete block design 完全区集法Complete confounding 完全交络Complete dissociation 全不相联Complete failure 完全故障,完全失效Completely randomized design 完全随机法Complaint 抱怨Complaint index 抱怨指标Completed product verification 成品验证Component 组件,组件Component bar chart 成份条图Component distiibution 组成份分配(布)Component part diagram 成份图Component ratio 成份比Component reliability 组件可靠度Component variance 成份变异数Components of variance 变异数成份Composite curve 复合曲线Composite design 复合法Composite hypothesis 复合假设,组合假设Composite unit 复合单位Compound distribution 复合分配(布)Compound event 复合事件Compound probability 复合机率Compounding technique 复合法Compressed limit 压缩界限Compressed limit gauging 压缩界限规则Computed value 计算值Concentric circle diagram 同心圆图Conception of limit 极限概念Conceptual design 概念设计Conceptual design review 概念设计审查Concession 特采,特认Concomitant factor 共变因素Concomitant variable 共变数Concomitant variation 共变异Concurrency 并行Condition maintenance 状态维护Condition monitoring 状态监督Condition-based maintenance 状态基准维护Conditional probability 条件机率Conditions of use 使用条件Confidence 信任,信赖Confidence coefficient 信任系数,信赖系数Confidence interval 信任区间,信赖区间Confidence in test results 试验结果的信赖度Confidence level 信任水平,信赖水平Confidence limit 信任界限,信赖界限Confidence range 信任全距,信赖全距Configuration control 型态管制Configuration items 型态件Configuration management 型态管理Confirmation 确认Conformance to the requirement 符合要求Conformation 一致Conforming article 合格品Conformity 符合Confounding 交络Confounding, complete 完全交络Confounding, partial 部份交络Connector 连接器Consignment 委托,寄售Consistency 一致性Constancy 恒久性Constancy of great numbers 大数恒久性Constant 常数Constant cause system 恒常原因系统Constant error 恒常误差Constant failure period 恒常失效期Constant failure rate dustribution 恒常失效率分配(布)Constant weight (Fixed weight) 固定权数Constraint 束缚Consultant 管理顾问师Consumer 消费者Consumer acceptance specification 消费者允收规格Consumerism 消费者主义Consumer's risk (CR) 消费者冒险率Consumer test panel 消费者试验小组Consumer preference 消费者偏好Consumer sensitivity test 消费者感官试验Contingency 列联Contingency coefficient 列联系数Contingency table 列联表Contingency theorem 列联理论Continuity correction 连续校正Continuous change 连续变更Continuous data 连续数据Continuous distribution 连续分配(布)Continuous production 连续生产Continuous sampling 连续抽样Continuous sampling plan (CSP) 连续抽样计划Continuous series 连续数列Continuous variable 连续变量Contract 合约Contract preparation 拟定合约Contract review 合约检讨Contract requirements 合约需求Contract requirements analysis 合约需求分析Contractors 合约商Contrast analysis 对照分析Control, in 在管制(状态)下Control, lack of 缺乏管制Control, out of 超出管制Control, state of 管制状态Control, under 在管制(状态)下Control chart 管制图Control chart, cumulative sum 累积和管制图Control chart, defects per unit 每单位内缺点数管制图Control chart, two-way 双向管制图Control chart factor 管制图系数Control chart for attribute 计数值管制图Control chart for variable (measurement) 计量值管制图Control chart method 管制图法Control chart pattern 管制图类型Control factor 管制因素Control gaging (gauging) 管制规测Control level 管制水平Control limit 管制界限Control limit, lower 管制下限Control limit, modified 修正管制界限Control limit, upper 管制上限Control limit factor 管制界限因子Control line 管制线Control of measuring and test equipment 量测与试验设备之管制Control of nonconforming material 不合格物料之管制Control of nonconforming product 不合格产品之管制Control of production 生产管制Control of reliability 可靠度管制Control of verification status 验证状况之管制Control plan 管制计划Control point 管制点Control station 管制站Control system 管制系统Controllability 可管制性Controlled process 管制制程Controlled state 管制状态Controlled variability 管制变异性Controlled variable 管制变数Controlling item 管制项目Convenience lot 合宜的批Convergence 收敛Cooked distribution 中断分配(布)Coordinate 坐标Coordinate axis 坐标轴Coordinate line 坐标线Coordination 协调Coordination for reliability 可靠度协调Correction 校正,修正Correction, Sheppard Sheppard 校正数Correction factor 修正因子Correction for continuity 连续校正Correction for mean 平均数校正Correction term 校正项Corrective action 矫正行动,改正措施Corrective maintenance 矫正维护,改正维护Corrective maintenance time 矫正维护时间,改正维护时间Corrective sorting 修正选别Correlated measure 相关量数Correlated samples 相关样本Correlation 相关Correlation, coefficient of 相关系数Correlation, direct 直接相关Correlation, index of 相关指数Correlation, inverse 反相关Correlation, multiple 复相关Correlation, negative 负相关Correlation, net 净相关Correlation, nonlinear 非线性相关Correlation, nonsense 无意义相关Correlation, part 部份相关,偏相关Correlation, partial 部份相关,偏相关Correlation, perfect 完全相关Correlation, rank 等级相关Correlation, serial 数序相关Correlation, simple 简相关Correlation, zero 零相关Correlation analysis 相关分析Correlation chart 相关图Correlation, coefficient 相关系数Correlation coefficient, rank 等级相关系数Correlation matrix 相关矩阵Correlation of attributes 品性相关Correlation ratio 相关比Correlation of x on y x与y的相关比Correlation ratio of y on x y与x的相关比Correlation scatter chart 相关散布图Correlation surface 相关面Correlation table 相关表Correlation theory 相关理论Correlogram 相关图Corrosive atmosphere 腐蚀性空气Cost 成本,费用Cost, acquisition 取得成本Cost, appraisal 评估(鉴定)成本Cost, external failure 外部失败成本Cost, internal failure 内部失败成本Cost, life cycle 寿命周期成本Cost, logistic 后续成本Cost, prevention 预防成本Cost, quality 质量成本Cost, quality control 质量管理成本Cost, rework 重加工成本Cost effectiveness 成本效益Cost function 成本机能Cost model for reliability optimization 可靠度最佳化成本模式Cost reduction 成本减低Count (Countable) data 点计数据Counter variation 反行变异Co-variation 共变异Covariance 共变异数,共变数Covariance analysis 共变异数分析Covariance matrix 共变异矩阵Craps, game of 掷骰游戏Credibility 信用Creep failure 潜变失效,潜变故障Crest 峰Criteria for workmanship 工作技艺准则Criterion 准则,规范Criterion, acceptance 验收准则(规范)Critical component control 重要组件管制Critical defect 严重缺点Critical defective 严重不良品Critical design review 关键设计审查Critical failure 关键故障,严重失效Critical items 关键品目,重要件Critical path 要径Critical path analysis 要径分析法Critical region 临界区域,弃却区域,判定区Critical value 临界值,判定值Criticality 严重性,关键性Cross 交叉Cross check 互校Cross classification 交叉分类Cross correlation 交叉相关Cross formula 交互公式Cross-hatch 交叉线Cross-hatched map 交叉图Cross-over design 交叉计划Crossed design 交叉法Crude mode 概括众数Crude moment 概括动差Cubic chart (diagram) 立方图Culled 检选Cumulant 累积数Cumulation, downward 向下累积Cumulation, total 全部累积Cumulation, upward 向上累积Cumulation average chart 累积平均数(管制)图Cumulative curve 累积曲线Cumulative curve chart 累积曲线图Cumulative damage 累积损坏Cumulative distribution (Ogive) 累积分配(布)Cumulative distribution function 累积分配(布)函数Cumulative error 累积误差Cumulative failure frequency 累积故障次数,累积失效次数Cumulative frequency 累积次数Cumulative frequency arrangement 累积次数排列Cumulative frequency curve 累积次数曲线Cumulative frequency 累积次数曲线图Cumulative frequency distribution 累积次数分配(布)Cumulative frequency polygon 累积(次数)多边形Cumulative frequency (probability) function 累积次数(机率)函数Cumulative frequency table 累积次数表Cumulative function 累积函数Cumulative graph 累积图Cumulative hazard function 累积冒险函数Cumulative mean 累积平均数Cumulative normal distribution 累积常态分配Cumulative number of failures 累积失效数,累积故障数Cumulative percentage of failures 累积失效百分率,累积故障百分率Cumulative probability distribution 累积机率分配(布)Cumulative sum 累积和Cumulative sum chart 累积和(管制)图Cumulative sum control chart 累积和管制图Cumulative terms 累积项Curtailed (Truncated) inspection 截略检验Curtailed (Truncated) sample inspection截略样品检验Curtailed sampling 截略抽样Curtailed sampling inspection 截略抽样检验Curtaijed sampling plan 截略抽样计划Curtailment of sampling plan 抽样计划之截略Curve 曲线Curve, frequency 次数曲线Curve, normal 常态曲线Curve chart (diagram) 曲线图Curve fitting 曲线配合Curve of error 误差曲线Curve of means 平均数曲线Curve of probability 机率曲线Curve type criterion 曲线型准则Curve shape 曲线形状Curvilinear correlation 曲线相关Curvilinear regression 曲线回归Curvilinear trend 曲线趋势Curvilinearity 曲线性Customer 客户,顾客Customer complaint 顾客抱怨Customer feedback information 顾客回馈信息Customer incurred cost 顾客引发成本Customer operation cost 顾客作业成本Customer repair cost 顾客修理成本Customer requirement 顾客要求Customer satisfaction 顾客满意度Customer's need 顾客需要Cusum chart 累积和(管制)图Cycles 周期Cycles between failures 失效间隔周期,故障间隔周期Cycle of operation 操作周期Cyclic curve 周期(循环)曲线Cyclic damage 周期性损坏Cyclic load 周期性负荷Cyclical deviation 周期(循环)离差Cyclical fluctuation 周期波动Cyclical trend 周期趋势Cyclical movement 周期移动Cyclical variation 周期变异Cycling failure rate 周期性失效率,周期性故障率DD chart d管制图Data 数据Data analysis 数据分析Data bank 资料室(库)Data exchange program 数据交换计划Data, inspection 检验数据Data item 数据项,文件项目Data processing 数据处理Death rate 死亡率Debug (debugging) 除错Decile 十分位数Decimal fraction 小数Decision function 决策函数Decision line 决定线Decision making 决策Decision variable 决策变数Decreasing failure rate distribution 递减失效率分配(布)Decrement 减量Decrement rate 减率Defect 疵病,缺点Defect, chronic 慢性缺点Defect, critical 严重缺点Defect, incidental 偶发缺点Defect, major 主要缺点Defect, minor 次要缺点Defect, sporadic 突发缺点Defect and failure analysis 缺点与失效分析Defect chart 缺点数(管制)图Defect Free 零缺点Defect prevention 缺点预防Defects, number of 缺点数Defects classification 缺点分类Defects per hundred units (dphu) 百件缺点数Defects per unit chart 每单位(内)缺点数(管制)图Defects per unit plan 每单位(内)缺点数(管制)计划Defective 不良品Defective, fraction 不良率Defective chart 不良品数(管制)图Defective material 不良材料Defective number 不良品数Defective part 不良零件Defective parts, percentage of 不良零件百分率Defective prevention 不良品预防Defective unit 不良品(单位)Defectives, number of 不良(品)数Defectives classification 不良品分类Definition(s) 定义Deflated series 调节数列Deflated value 调节值Deflating index 调节指数Degradation 劣化Degradation failure 劣化故障,劣化失效Degree of accuracy 准确度Degree of approximation 近似度Degree of association 相联度Degree of confidence 信任(赖)度Degree of contribution 贡献度Degree of freedom (DF) 自由度Degree of reliability 可靠度Delivery 交货,出厂Delivery inspection 出厂检验Delivery qulaity 出厂品质Delivery time 运送时间Demerit 减点Demerit chart 减点(数)(管制)图Demerit rating 减点评比Demerits per unit 每单位(内)减点数Demonstration 示范,验证,展现Demonstration test 验证试验,展现试验Density function 密度函数Dependability 可恃性,相依性,依赖性Dependent factor 因变因子Dependent failure 相依失效,相依故障Dependent variable 因变数Derating 降等,额降,减额定Derivation 导出Derived table 导出表Descriptive item 说明项Descriptive statistics 记述统计(学)Design 设计Design baseline 设计准则Design change 设计变更Design considerations 设计考虑Design control 设计管制Design change control 设计变更管制Design control, new 新设计管制Design criterion 设计准则Design disclosure package 设计启导文件Design effect cost 设计效应成本Design freeze 设计冻结Design in 设计进去Design input 设计输入Design matrix 设计矩阵Design output 设计输出Design of experiment 实验计划Design planning 设计规画Design profile 设计轮廓Design proving 设计认可Design qualification 设计之合格性Design release 设计发布Design requalification 设计合格之再认定Design review 设计审查Design specification 设计规格Design validation 设计确认Design verification 设计验证,查证Design verification test 设计验证试验Designation 名称Designed experiment 实验计划Destructive inspection (test) 破坏性检验(试验)Detailed design 细部设计Detailed design review 细部设计审查Detailed inspection (100% inspection) 全数检验(百分之百检验)Detect 侦测Detection of a failure unit 失效单位之检测,故障单位之检测Detection time 检测时间Deterioration 衰变,劣化。

质量控制中英文对照

质量控制中英文对照

QE=品质工程师(Quality Engineer)MSA: Measurement System Analysis 量测系统分析LCL: Lower Control limit 管制下限Control plan 管制计划Correction 纠正Cost down 降低成本CS: customer Sevice 客户中心Data 数据Data Collection 数据收集Description 描述Device 装置Digital 数字Do 执行DOE: Design of Experiments 实验设计Environmental 环境Equipment 设备FMEA: Failure Mode and Effect analysis 失效模式与效果分析FA: Failure Analysis 坏品分析FQA: Final Quality Assurance 最终品质保证FQC: Final Quality control 最终品质控制Gauge system 量测系统Grade 等级Inductance 电感Improvement 改善Inspection 检验IPQC: In Process Quality Control 制程品质控制IQC: Incoming Quality Control 来料品质控制ISO: International Organization for Standardization 国际标准组织LQC: Line Quality Control 生产线品质控制LSL: Lower Size Limit 规格下限Materials 物料Measurement 量测Occurrence 发生率Operation Instruction 作业指导书Organization 组织Parameter 参数Parts 零件Pulse 脉冲Policy 方针Procedure 流程Process 过程Product 产品Production 生产Program 方案Projects 项目QA: Quality Assurance 品质保证QC: Quality Control 品质控制QE: Quality Engineering 品质工程QFD: Quality Function Design 品质机能展开Quality 质量Quality manual 品质手册Quality policy 品质政策Range 全距Record 记录Reflow 回流Reject 拒收Repair 返修Repeatability 再现性Reproducibility 再生性Requirement 要求Residual 误差Response 响应Responsibilities 职责Review 评审Rework 返工Rolled yield 直通率sample 抽样,样本Scrap 报废SOP: Standard Operation Procedure 标准作业书SPC: Statistical Process Control 统计制程管制Specification 规格SQA: Source(Supplier) Quality Assurance 供应商品质保证Taguchi-method 田口方法TQC: Total Quality Control 全面品质控制TQM: Total Quality Management 全面品质管理Traceability 追溯UCL: Upper Control Limit 管制上限USL: Upper Size Limit 规格上限Validation 确认Variable 计量值Verification 验证Version 版本QCC Quality Control Circle 品质圈/QC小组PDCA Plan Do Check Action 计划执行检查总结Consumer electronics 消费性电子产品Communication 通讯类产品Core value (核心价值)Love 爱心Confidence 信心Decision 决心Corporate culture (公司文化)Integration 融合Responsibility 责任Progress 进步QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数SSQA standardized supplier quality audit 合格供应商品质评估FMEA failure model effectiveness analysis 失效模式分析AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 品质/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制GRR Gauge Reproducibility & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径QIT Quality Improvement Team 品质改善小组ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准IWS International Workman Standard 工艺标准ISO International Standardization Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DCC Document Control Center 资料控制中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证处QC Quality Control 品质管制(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部。

质量术语中英文对照

质量术语中英文对照

质量管理中英文名词对照质量管理中英文名词对照表Accuracy 准确度Active 主动Action 评价.处理Activity 活动Add 加Addition rule 加法运算规则Analysis Covariance 协方差分析Analysis of Variance 方差分析Appraisal Variation 评价变差Approved 承认ASQC 美国质量学会Attribute 计数值Audit 审核Automatic database recovery 数据库错误自动回复Average 平均数balance 平衡Balance sheet 资产负债对照表Binomial 二项分配Body 机构Brainstorming Techniques 脑力风暴法Business Systems Planning 企业系统规划Cable 电缆Capability 能力Cause and Effect matrix 因果图.鱼骨图Center line 中心线check 检查Check Sheets 检查表Chi-square Distribution 卡方分布Clutch spring 离合器弹簧Coining 压印加工Common cause 共同原因Complaint 投诉Compound factor 调合因素Concept 新概念Condenser 聚光镜Conformity 合格Connection 关联Consumer’s risk 消费者之风险Control 控制Control characteristic 管制特性Control chart管制图Control plan 管制计划Correction 纠正Correlation Methods 相关分析法Cost down 降低成本CPI: continuouse Process Improvement 连续工序改善Creep 渐变Cross Tabulation Tables 交叉表CS: customer Sevice 客户中心Cushion 缓冲Customer 顾客DSA: Defects Analysis System 缺陷分析系统Data 数据Data Collection 数据收集Data concentrator 资料集中缓存器DCC: Document Control Center 文控中心Decision 决策.判定Defects per unit 单位缺点数Description 描述Detection 难检度Device 装置Digital 数字Do 执行DOE: Design of Experiments 实验设计Element 元素Else 否则Engineering recbnology 工程技术Entropy 函数Environmental 环境Equipment 设备Estimated accumulative frequency 计算估计累计数EV: Equipment Variation 设备变异Event 事件External Failure 外部失效,外部缺陷FA: Failure Analysis 坏品分析Fact control 事实管理Fatique 疲劳FMEA: Failure Mode and Effect analysis 失效模式与效果分析FPY 合格率FQA: Final Quality Assurance 最终品质保证FQC: Final Quality control 最终品质控制Full-steer 完全转向function 职能Gauge system 量测系统Grade 等级Gum-roll 橡皮滚筒Health meter 体重计Heat press 冲压粘着Histogram 直方图Hi-tech 高科技hypergeometric 超几何分配hysteresis 磁滞现象Improvement 改善Inductance 电感Information 信息Initial review 先期审查Inspection 检验Internal Failure 内部失效,内部缺陷IPQC: In Process Quality Control 制程品质控制IQC: Incomming Quality Control 来料品质控制ISO: International Organization for Standardization 国际标准组织Law of large number 大数法则Link 连接LCL: Lower Control limit 管制下限LQC: Line Quality Control 生产线品质控制LSL: Lower Size Limit 规格下限Machine 机械Manage 管理Materials 物料Measurement 量测Median 中位数Miss feed 漏送Module,sub-system,sub-unit 单位Momentum 原动力Monte garlo method 原子核分裂热运动法MSA: Measurement System Analysis 量测系统分析Multiplication rule 乘法运算规则NIST 美国:标准技术院Normal 常态分布Occurrence 发生率On.off system 开,关系统Operation Instruction 作业指导书Organization 组织Parameter 参数Parto 柏拉图Parts 零件Parts per million 不良率Passive 消极的,被动的Plan 计划Pulse 脉冲Policy 方针Population 群体Power 力量,能源PQA: Process Quality Assurance 制程品质保证Practice 实务Precision 精密度preemptive 先占式多任务Pressure 压缩Prevention 预防Probability 机率Probability density function 机率密度函数Procedure 流程Process 过程Process capability analysis 制程能力分析图Process control and process capability 制程管制与制程能力Producer’s risk 生产者之风险Product 产品Production 生产Program 方案Projects 项目QA: Quality Assurance 品质保证QC: Quality Control 品质控制QE: Quality Engineering 品质工程QFD: Quality Function Desgin 品质机能展开Quality 质量Quality manual 品质手册Quality policy 品质政策Random experiment 随机试验Random numbers 随机数Range 全距Record 记录Reflow 回流Reject 拒收Repair 返修Repeatusility 再现性Reproducibility 再生性Requirement 要求Residual 误差Response 响应Responsibilities 职责Review 评审Reword 返工Robustness 稳健性Rolled yield 直通率RPN: Risk Priority Number 风险系数sample 抽样,样本Sample space 样本空间Sampling with replacement 放回抽样Sampling without peplacement 不放回抽样Scatter diagram 散布图分析Scrap 报废Screw 螺旋Severity 严重度Shot-peening 微粒冲击平面法Simple random sampling 简单随机取样Size 规格SL: Size Line 规格中心线Slip 滑动Stratified random sampling 分层随机抽样SOP: Standard Operation Procedure 标准作业书SPC: Statistical Process Control 统计制程管制Special cause 特殊原因Specification 规范SQA: Source(Supplier) Quality Assurance 供货商品质保证Stage sampling 分段随机抽样Standard Deviation 标准差Sum of squares 统计表supplier 平方和System 供方systematic sampling 系统,体系Statistical tables 系统抽样Taguchi-method 田口方法Technical committees 技术委员会Test piece 测试片Theory 原理Time stamp 时间戳印Time-lag 延迟Title 标题Torque 转矩Total 求和TQC: Total Quality Control 全面品质控制TQM: Total Quality Management 全面品质管理Traceablity 追溯Training 培训Transaction processing and logging 交易处理Trouble 困扰Up and down 上和下UCL: Upper Control Limit 管制上限USL: Upper Size Limit 规格上限Validation 确认Variable 计量值Variance 变异和Vector 向量Verification 验证Version 版本VOC: voice of Customer 客户需求VOE: Voice of Engineer 工程需求。

常用词汇英汉互译

常用词汇英汉互译

一般质量词汇(Quality)1ABC analysis2Accelerated life test3Accelerated test4Acceptability criterion5Acceptable limit6Acceptable process7Acceptable quality8Acceptable quality level (AQL)9Acceptable reliability level (ARL)10Acceptance11Acceptance and rejection criteria12Acceptance criteria13Acceptance inspection14Acceptance limit15Acceptance plan16Acceptance procedure17Acceptance product18Acceptance sampling, attribute19Acceptance sampling, variable20Accepting lot21Accuracy22Acronym23Action24Action, corrective25Agreement on verification method 26Allowable percent defective(Acceptable quality level, AQL)27Allowance28American National Standards Institute (ANSI)29American Society for MechanicalEngineers (ASME)30American Society for Quality Control (ASQC)31American Society for Testing andMaterials (ASTM)32American Standard Association (ASA) 33Anti-Static Tray34Anti-Static Tray35Applied statistics36Appraisal cost37Appraisal of quality38Approved Parts List39Approved Vendor List40AQL (Acceptable quality level) 41AQL(Acceptable Quality Level) 42Assignable cause (Special cause) 43Assurance function44Assurance quality45Attribute classification46Attribute data47Attribute inspection48Attribute sampling49Attribute sampling plan50Audit plan51Audit report52Average outgoing quality limit 53Bad lot54Bar chart (diagram)55Bar Code56Batch (Lot)57Batch of material58Batch process59Batch size60Batch testing61Bilateral62BOM(Bill of Materials)63BOM(Bill of Materials)64Brainstorming65Buyer66 C chart67Calibration68Capability69Capability, machine70Capability, process71Capacity72Carton73Carton74Category75Cause and effect diagram76Cause And Effect Diagram77Cause, assignable78Cause, avoidable79Cause, chance80Cause, common81Cause, random82Cause, special83Certification84Certified quality engineer (CQE) 85Certified quality technician (CQT) 86Certified reliability engineer (CRE) 87Characteristic88Characteristic curve, operating (OC 89Characteristic diagram90Characteristic function91Characteristic operating curve (OC 92Characteristic, qualitative93Characteristic, quantitative94Chart95Chart, control96Chart, percent defective97Check Sheets / Tally Charts98Classification of defectives99Classification of defects100Classification of failure101Clearance102Code103Code letter104Coefficient105Commissioning106Commodity107Common cause (Chance cause) 108Company standard109Company-wide quality control 110Complaint111Completed product verification 112Concession; Waiver113Confirmation114Conformance to the requirement 115Conformation116Conforming article117Conformity118Consignment119Consistency120Consumer121Contact, Terminal122Continuous production123Continuous sampling124Contract125Contract requirements126Contractors127Control chart128Control limit129Control limit, lower130Control limit, upper131Control line132Control of nonconforming material 133Control of nonconforming product 134Control of production135Control plan136Control point137Control station138Control, in139Control, out of140Control, under141Controlled process142Corrective action143Cosmetics, Appearance144Cost, appraisal145Cost, external failure146Cost, internal failure147Cost, quality148Cost, rework149Criteria for workmanship150Criteria of Inspection for BatteryAssembly151Criteria of inspection for Plastic parts 152Criterion153Criterion, acceptance154Critical Characteristic155Critical defect156Critical defective157Cumulative frequency158Customer159Customer complaint160Customer requirement161Customer satisfaction162 D chart163Data164Data analysis165Data processing166Data, inspection167Defect168Defect and failure analysis 169Defect chart170Defect Free171Defect, chronic172Defect, critical173Defect, major174Defect, minor175Defect, sporadic176Defective177Defective, fraction178Defects classification179Definition(s)180Delivering181Delivery182Delivery inspection183Delivery quality184Delivery time185Demonstration186Design change187Design control188Design criterion189Design of experiment (DOE) 190Design planning191Design qualification192Design release193Design review194Design specification195Design validation196Design verification197Designed experiment198Deviation199Deviation, standard200Diagram, scatter201Dimension202Disassemble203Discrepant material204Document approval and issue205Document changes and modifications 206Document control207Documentation208Documentation of the quality system 209Double specification210Economic quality211Efficiency212Electrical Test213Element214Engineer, quality215Engineer, quality control216Environment control217Environment test218Environmental stress219Environmental stress screening220Environmental test specification221Environmental testing222Ergonomics223Examination224Experiment, design of225Exterior Carton226Fabricated material227Failure analysis228Failure cause229Feedback230Field data231Field failure data232Field quality233Final Article Inspection234Final design review235Final inspection236Final product specification237Final rejection238Finger Cot239Finished goods lot rejection rate (%) 240First Article241First article(piece) Inspection242Fishbone diagram243Fixture244Flexibility245Flow chart (diagram)246Follow-up247Frequency248Gage (Gauge)249Gage inspection250Gage, block251Glossary252Go253Go and not-go254Gold Sample255Go-no-go256Good lot257Green-dot-label258Guideline(s)259Handling260Hand-sorting method261Histogram262Histogram263Histogram264Histogram, frequency265Historical series266Housing267Human engineering268Humidity269Identification270Identification of inspection and test status271Identification of nonconforming 272Identification stamp273Identify274Improvement Plan275Incoming Inspection276Incoming lot quality277Incoming lot rejection rate (%) 278Incoming material279Incoming material control280Incoming material inspection281Initial failure282In-process inspection283In-Process Inspection284Inspection285Inspection and test record286Inspection and test status287Inspection and Test Status288Inspection by attribute289Inspection by batch290Inspection by variable291Inspection lot292Inspection measuring and test 293Inspection method294Inspection plan295Inspection procedure296Inspection record297Inspection specification298Inspection station299Inspection, 100%300Inspection, curtailed301Inspection, in line302Inspection, in process303Inspection, manual304Inspection, normal305Inspection, original306Inspection, patrol307Inspection, process308Inspection, reduced309Inspection, sampling310Inspection, tightened311Inspector312Inspector, patrol313Inspector, roving314Installation315Interchangeability316Job description317Job rotation318Job shop (vs. Mass production job) 319Job specification320Labeling321Labeling322Lack of control323Learning324Level, acceptable quality (AQL) 325Limit, average outgoing quality 326Limit, control327Limit, specification328Loss of confidence329Lot (Batch)330Lot Control331Lot tolerance percent defective (LTPD) 332Lower control limit (LCL)333Machine capability334Machine capacity335Maintenance336Maintenance337Maintenance records338Major defect339Major defective340Malfunction341Management representative342Management responsibility343Management review344Management system345Man-power346Manual inspection347Manual Soldering348Manufacturability349Manufacturing control350Manufacturing process351Marking352Mass production353Material inventory354Material Review Board (MRB)355Material Review Board(MRB)356Material specification357Mean life358Mean time between failures (MTBF) 359Measurement, system360Minor defect361Minor defective362Minor failure363Monitor364Negative correlation365Nominal dimension366Nominal specification367Non-conformance368Non-conforming article369Non-conforming product370Nonconformity371Nonconformity Analysis372Non-destructive inspection373Non-destructive testing (NDT) 374Non-replacement375Number of defects376Objective377Objective value378One hundred percent inspection 379On-Line QC380OOBA, Out of Box Audits381Operating characteristic curve 382Operation383Operations research (OR)384Operator385Operator control386Outgoing Inspection387Outgoing return rate (PPM)388P chart389P chart390Packaging391Packing List392Pareto analysis393Pareto curve394Pareto diagram395Pareto principle396Parts control397Parts inspection398Patrol inspection399Patrol inspector400Percent defective401Percent defective chart402Pilot plant403Pilot production404Pilot run405Pilot Run406Plan of acceptance407Planning for controlled production 408Power of test (1-β)409Preliminary Review (PR)410Preventive action411Preventive maintenance412Problem solving process (PSP) 413Procedure chart414Process415Process416Process average417Process average fraction defective 418Process average quality419Process capability420Process Capability421Process control422Process Control423Process control chart424Process defect rate (PPM)425Process engineer426Process Flow Chart427Process Flow Chart428Process Improvement429Process inspection430Process modification431Process quality432Process variation433Procurement434Product435Product acceptance436Product assurance437Product engineer438Product specification439Product verification440Production control441Production foreman442Production line443Production permit444Production planning445Production release446Production supervisor447Productivity448Prototype449Purchaser450Purchaser supplied product451Purchasing452QC circle453Qualification454Qualification test455Qualified products list456Quality457Quality assurance (QA)458Quality audit459Quality auditor460Quality awareness461Quality characteristic462Quality consciousness463Quality control (QC)464Quality control engineer465Quality control manual466Quality control, statistical (SQC) 467Quality cost468Quality engineer469Quality improvement470Quality improvement program 471Quality Improvement Project (QIP) 472Quality level473Quality loop474Quality management475Quality manager476Quality manual477Quality objective478Quality policy479Quality responsibility480Quality responsibility and authority 481Quality spiral482Quality surveillance483Quality system audit484Quality system principle485Quality system procedure and 486Quality system requirement487Quality system review488Quality, acceptable489Quality, average outgoing490Quantitative characteristic491Quantity492Range493Raw data494Raw material495Raw material inspection496Reading497Recall498Receiving inspection499Receiving inspection and testing 500Receiving quality record501Reciprocal matrix502Reduced inspection503Reduced testing plan504Reference standard505Region of acceptance506Region of doubt507Region of rejection508Reject limit509Reject lot510Rejectable process level511Rejectable quality level (RQL) 512Rejectance number (Re)513Rejected product514Rejection515Reliability516Reliability analysis517Reliability Test518Repair519Replaceability520Representation sample521Representative sample522Requirement for specifications 523Responsibility524Responsibility and authority 525Resubmitted lots526Reuseable527Review and evaluation of quality management system528Revision529Rework530Rework analysis531Roving inspection532S Chart533Safety534Salt-spray test535Sample536Sample, representative537Sampling538Sampling Inspection539Sampling, acceptance540Scale541Scatter542Scatter diagram543Schedule544Scope545Scrap546Screening547Screening inspection548Screening process549Segregating550Selection of model for quality 551Selection of qualified supplier 552Self Inspection553Sensitivity554Sequence555Sequence556Setup criteria557Shipping558Shock test559Shop operation560Single specification561Size, lot562Size, sample563Sorting inspection564Spare parts565Special process566specification conflict567specification limit568specification limit, double569specification limit, single570specification, nominal571specification, revision of572Standard of Inspection573Standard Repair Procedure (SRP) 574Statistical diagram575Statistical Process Control576Statistical Process Control (SPC) 577Statistical quality control (SQC)578Statistically stable579Stocking580Storage581Stratification582Subcontractor583Supervisor584Supplier585Supplier measurement control 586Suppliers monitoring and control 587Supplies588Surveillance589Symbol590Symbols, glossary of591Technical personnel592Technician593Technology594Temporary standard595Tentative standard596Term597Terminology598Test599Test data600Test equipment601Test method602Test planning603Test procedure604Thermometer chart (Bar chart) 605Tightened inspection606Tolerance607Tolerance, bilateral608Tolerance, unilateral609Tool610Tooling611Top management612Traceability613Traceability of material614Transportation615Trend616Trend chart617Trial lot618Trial production619Trivial many620Trouble shooter621Trouble-shooting622U chart623Uniformity624Unilateral625Upper control limit (UCL)626User instruction627Validity628Value analysis (VA)629Value engineering (VE)630Variable631Variable sampling plan632Variance (σ^2)633Variance, analysis of (ANOVA)634Vendee635Vendor636Vendor quality rating637Vendor rating system638Vendor record card639Verification640Verification inspection641Verification of purchased product 642Vibration test643Visual aid644Visual inspection645Vital few646Waiver647Warranty period648Waste product649Wire Arranging650Work instruction651Work Instruction, Standard Of652Worker653Workmanship654Workmanship655Workmanship Standard for soldering 656Workshop657Yield658Zero defects (ZD)659Zone of acceptance660Zone of rejectionABC 分析加速寿命试验加速试验允收标准允收界限允收制程水平允收品质允收质量水平允收可靠度水平允收,验收允收与拒收准则允收准则验收检验允收界限验收计划验收程序允收品计数值验收抽样计量值验收抽样允收批准确度缩写行动,措施矫正行动(措施)验(查)证方法之协议允收不良率(允收质量水平)允差,裕度美国标准协会美国机械工程师学会美国质量管理学会美国材料试验学会美国标准协会防静电盘防静电盘应用统计学鉴定成本,评估成本质量评估合格物料清单合格供货商名录允收(质量)水平允收质量水平非机遇原因(特殊原因)保证功能保证质量品性分类计数数据计数值检验计数值抽样计数值抽样计划稽核计划稽核报告平均出厂水平坏批条(形)图条形码批材料批分批制造方法批量批试验双边物料清单物料清单脑力激荡法买方; 客户C(管制)图校正能力机器能力制程能力能量, 容量纸箱纸箱类别特性要因图特性要因图非机遇原因可避免原因机遇原因共同原因随机原因特殊原因验证合格质量工程师合格质量技术师合格可靠度工程师(质量)特性操作特性曲线,OC曲线特性要因图特性函数特性操作曲线(OC曲线)质的特性量的特性图,(管制)图管制图不良率管制图查检表不良品分类缺点分类失效分类, 故障分类间隙, 余隙简化, 代号代字系数委制商品共同原因(机遇原因)公司标准全公司质量管理抱怨成品验证特采,特认确认符合要求一致合格品符合委托, 寄售一致性消费者端子连续生产连续抽样合约合约需求合约商管制图管制界限管制下限管制上限管制线不合格物料之管制不合格产品之管制生产管制管制计划管制点管制站在管制(状态)下超出管制在管制(状态)下管制制程矫正行动, 改正措施外观评估(鉴定)成本外部失败成本内部失败成本质量成本重加工成本工作技艺准则电池组装检验规范塑料件检验标准准则, 规范验收准则(规范)重要特性严重缺点严重不良品累积次数客户, 顾客顾客抱怨顾客要求顾客满意度d管制图数据数据分析数据处理检验数据疵病,缺点缺点与失效分析缺点数(管制)图零缺点慢性缺点严重缺点主要缺点次要缺点突发缺点不良品不良率缺点分类定义运送交货,出厂出厂检验出厂品质运送时间示范,验证,展现设计变更设计管制设计准则实验计划设计规画设计之合格性设计发布设计审查设计规格设计确认设计验证,查证实验计划离差标准偏差散布图尺寸拆装不适宜材料文件核发文件变更与修订文件管制文件化,字处理,书面化质量系统文件处理,文件化双边规格经济质量效率电气测试单件,组件质量工程师质量管理工程师环境环境试验环境压力,环境应力环境应力筛选环境试验规格环境试验人因学查验实验计划外箱制程材料故障分析,失效分析故障原因,失效原因回馈实地数据,现场数据现场故障数据,实地失效数据现场品质终检,成品检验最终设计审查最终检验成品规格最终拒收指套成品批退率首件首件检验鱼骨图治具弹性流程图跟催次数,频率量规量规检验块规词汇,术语辞典通过通过及不通过标准样品通过不通过好批绿点标签指导纲要搬运人工分选法直方图历史图直方图次数直方图时间数列外壳人因工程湿度鉴别检验及测试状况识别不合格产品识别证明章,识别章鉴定,鉴别改善计划进料检验进货(批)品质进料批退率进料进料管制进料检验初期故障,初期失效制程中检验制程检验检验检验与试验记录检验与试验状况检验测试状况计数值检验检验批计量值检验检验批检验、量测与试验设备检验方法检验计划检验程序检验记录检验规格检验站100%检验全数检验,100%检验生产在线检验制程中检验人工检验正常检验原始检验巡回检验制程检验减量检验抽样检验加严检验检验员巡回检验员巡回检验员安装交换性工作说明书工作轮调零星生产工作工场(相对于大量生产工作工场)工作规格标识标示缺乏管制烧机测试允收质量水平平均出厂质量界限管制界限丧失信心批批次管制批容许不良(百分)率,拒收水平管制下限机器能力机器能量维护,保养保养,维护维护记录主要缺点主要不良品故障管理代表管理阶层责任管理阶层审查管理系统人力人工检验手焊作业可制造性制造管制制造程序标示大量生产库存物料物料鉴审小组物料鉴审小组材料规格平均寿命平均失效间隔时间,平均故障间隔时间衡量(计测)系统次要缺点次要不良品次要失效监督负相关标称尺寸标称规格不符合不符合品不符合不合格分析非破坏性检验非破坏性试验不可更换缺点数目标目标值全数检验,100%检验(生产)线上品管开箱检验操作特性曲线,OC曲线作业作业研究作业员操作员管制出货检验出货退货率P(管制)图,不良率(管制)图R(管制)图,全距管制图包装包装清单PARETO 分析,柏拉图分析PARETO 曲线,柏拉图曲线PARETO图PARETO 原理,柏拉图原理零件管制零件检验巡回检验巡回检验员不良率不良率(管制)图试验工场试验生产,先导生产试运转试产验收计划管制生产之计划检定力先期审查预防措施(行动)预防保养,预防维护问题解决程序图制(造)程(序)制程制程平均制程平均不良率制程平均质量制程能力制程能力制程管制制程管制制程管制图制程不良率制程工程师制造流程表制造流程图制程改善制程检验制程之修改制程品质制程变异采购产品,乘积,生产产品验收产品保证产品工程师产品规格产品验证生产管制生产领班生产线生产特许生产计划准许生产开始生产现场之主管生产力原型,雏形购买者,采购者采购者提供之产品采购品管圈(小组)合格,认定鉴定试验,合格测试合格产品列表品质质量保证品质稽核品质稽核员质量意识质量特性质量意识质量管理质量管理工程师质量管理手册统计的质量管理质量成本质量工程师质量改进质量改进计划,质量改进方案质量改善项目质量水平品质环圈质量管理,质量经营质量经理品质手册质量目标质量政策,质量方针质量责任品质权责质量螺旋,质量螺线品质监察质量系统稽核品质系统策略质量系统与指导事项(质量系统程序与说质量系统要求质量系统审查允收特性平均出厂质量量的特性数量全距原始数据原料读数收回进料检验接收检验与测试接收检验计划与管制接收质量记录减量试验减量抽样计划参考标准允收区域可疑区域拒收区域拒收界限拒收批拒收制程水平拒收(质量)水平拒收数拒收(产)品拒收可靠度,可靠性可靠度分析信赖性试验修理可更换性代表样品代表性样本规格的要求责任权责覆验批可重复使用质量管理系统之审查与评估修订重作,重加工、返工重加工分析巡回检验S(管制)图,标准偏差(管制)图安全,安全性盐雾试验样本抽样抽样检验验收抽样标度,尺度散布散布图时程表范围废料,废品筛选(剔)筛选检验筛选方法隔离质量保证模式之选择合格供货商之选择自主检查灵敏度序列节次(工厂作业)建立准则出货冲击试验现场作业单边规格批量样本大小选分检验备件特殊制程规格抵触规格界限双边规格界限单边规格界限标称规格规格修订检验标准,检验规范标准维修程序统计图统计化制程管制统计化制程管制统计(的)质量管理统计的稳定入库储存层别法分包商主管,监督员供货商供货商之量测系统供货商监督与管制供应品监督,追查符号符号词汇表技术人员技术员工艺学暂行标准试用标准项目术语检定,试验,测试试验数据检定设备,试验装备检定法(试验方法)试验规画试验程序条图加严检验公差,允差双边公差单边公差工具模具高阶层管理人员可追溯性物料追溯性搬运趋势趋势图试作批试作生产琐细的多数追查员检修,故障排除,问题排除U (管制)图一致性单边管制上限使用说明书有效性价值分析价值工程变数; 计量值计量抽样计划变异数; 二次动差变异数分析买主供货商供货商品质分等供货商分等制度供货商记录卡验证验证检验采购产品之验证震动试验目视教材目视检验重要的少数特采; 特认保证时期; 保用期废品理线工作说明书作业指导书作业员手艺工程技艺手焊锡作业标准工场收率无缺点; 零缺点允收区域拒收区域。

质量英文单词

质量英文单词

部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA:Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点(CR)MAJOR DEFECT:主要缺点(MA)MINOR DEFECT:次要缺点(MI)MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限CPI:Continuous Process Improvement 连续工序改善Compatibility:兼容性Marking:标记DWG rawing图面Standardization:标准化Consensus:一致Code:代码ZD:Zero defect零缺点Tolerance:公差Subject matter:主要事项Auditor:审核员BOM:Bill of material物料清单Rework:重工ID:identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR:First Piece Inspection Report首件检查报告FAA:首件确认SPC:统计制程管制CP: capability index(准确度)CPK: capability index of process(制程能力) PMP:制程管理计划(生产管制计划)MPI:制程分析DAS efects Analysis System缺陷分析系统PPB:十亿分之一L/N:Lot Number批号Version:版本Quantity:数量Valid date:有效日期MO: Manafacture Order生产单TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT) DPPM: Defect Part Per Million(不良率的一种表达方式:百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC:允收REJ:拒收S/S:Sample size抽样检验样本大小SI-SIV:Special I-Special IV特殊抽样水平等级ISO:国际标准化组织ISA:Industry Standard Architecture工业标准体制结构PDCA:管理循环Plan do check action计划,执行,检查,总结WIP:在制品(半成品)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册AVL :认可的供货商清单(Approved Vendor List) QCD: Quality cost delivery(品质,交期,成本)KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S:Quality/Reliability/Service质量/可靠度/服务NTF:No trouble found误判CIP:capacity improvement plan(产能改善计划)MRB:material review board(物料审核小组)MRB:Material reject bill退货单JIT:just in time(即时管理)5S:seiri seiton seiso seiketsu shitsuke(整理,整顿,清扫,清洁,修养)SOP:standard operation process(标准作业程序)SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程) WI: working instruction(作业指导书)FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告ISAR :首批样品认可(Initial Sample Approval Request)- QCC :品管圈(Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)AOQ:Average Output Quality平均出货质量AOQL:Average Output Quality Level平均出货质量水平FMEA:failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA:Customer Simulate Analysis客户模拟分析SQMS:Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP:Quality Improvement Plan品质改善计划CIP:Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA:PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (品质工程表)DRP :运销资源计划(Distribution Resource Planning)DSS:决策支持系统(Decision Support System)EIS :主管决策系统(Excutive Information System)ERP:企业资源规划(Enterprise Resource Planning) FMS :弹性制造系统(Flexible Manufacture System) KM:知识管理(Knowledge Management)4L :逐批订购法(Lot-for-Lot)LTC :最小总成本法(Least Total Cost)LUC :最小单位成本(Least Unit Cost)MES :制造执行系统(Manufacturing Execution System) MPS :主生产排程(Master Production Schedule)MRP :物料需求规划(Material Requirement Planning) MRPⅡ:制造资源计划(Manufacturing Resource Planning) OEM :委托代工(Original Equipment Manufacture) ODM :委托设计与制造(Original Design & Manufacture)OLAP:线上分析处理(On-Line Analytical Processing) OLTP:线上交易处理(On-Line Transaction Processing) OPT :最佳生产技术(Optimized Production Technology) PDCA:PDCA管理循环(Plan-Do-Check-Action)PDM:产品数据管理系统(Product Data Management)) RCCP:粗略产能规划(Rough Cut Capacity Planning) SCM :供应链管理(Supply Chain Management)SFC :现场控制(Shop Floor Control)TOC:限制理论(Theory of Constraints)TQC :全面品质管制(Total Quality Control)S/T:Standard time标准时间TPM:total production maintenance:全面生产保养IT:information technology信息技术,资讯科学CEO:Chief Executive Officer执行总裁COO:Chief Operaring Officer首席业务总裁SWOT:Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence:专业能力Communication:有效沟通IDP:Individual Development Plan个人发展计划MRP:Material Requirement Planning物料需求计划MAT'S:Material材料LRR:Lot Rejeet Rate批退率ATIN:Attention知会5W1H:When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information 人力,机器,材料,方法, 市场,管理,资金,资讯______________________________________________________________________________________________________________ Pre-Inspection Area待检区Welcome To Download !!!欢迎您的下载,资料仅供参考!______________________________________________________________________________________________________________-可编辑修改-。

有关质量的专业术语中英文解释

有关质量的专业术语中英文解释

有关质量的专业术语中英文解释质量qua1ity:一组固有特性满足要求的程度;注:1术语“质量”可使用形容词,如:差、好、或优秀来修饰。

2.“固有的”(其反义是“赋予的”)是指本来就有的,尤其指永久的特性。

要求requirement:明示的、通常隐含的或必须履行的需求或期望;注:1“通常隐含的”是指组织、顾客和其他相关方的惯例或一般的做法,所考虑的需求或期望是不言而喻的。

2.特定要求可使用限定词表示,如:产品要求、质量管理体系要求、顾客要求。

3.规定要求是经明示的要求,如:在文件中阐明。

4.要求可由不同的相关方提出。

等级grade:对功能用途相同的产品、过程或体系所作的不同质量要求的分类或分级。

注:在确定质量要求时,等级通常是规定的。

顾客满意customersatisfaction:顾客对其要求已被满足程度的感受。

注:1顾客抱怨是一种满意程度低的最常见的表达方式,但没有抱怨并不一定表明顾客很满意。

2.即使规定的顾客要求符合顾客的愿望并得到满足,也不一定确保顾客很满,用'O能力ComPetence:经证实的应用知识和技能的本领。

注:1.在本标准中,所定义的能力的概念是通用的。

在ISo其他的文件中,本词汇的使用可能更加具体。

2.在GB/T19000族标准中,术语能力(capabi1ity)特指组织、体系或过程的“能力”。

有关管理的术语体系(系统)system:相互关联或相互作用的一组要素。

管理体系managementsystem:建立方针和目标并实现这些目标的体系。

注:一个组织的管理体系可包括若干个不同的管理体系,如质量管理体系、财务管理体系或环境管理体系。

质量管理体系qua1itymanagementsystem:在质量方面指挥和控制组织的管理体系。

质量方针qua1itypo1icy:由组织的最高管理者,正式发布的关于质量方面的全部意图和方向。

注:1.通常质量方针与组织的总方针相一致并为制定质量目标提供框架。

质量英语词汇大全(中英对照)

质量英语词汇大全(中英对照)

品质名词〔中英对照〕AABC analysis ABC 阐发Abnormality 不正常性Abscissa 横坐标Absolute deviation 绝对离差Absolute dispersion 绝对离势Absolute error 绝对误差Absolute frequency 绝对次数Absolute number 绝对数Absolute reliability 绝对可靠度Absolute term 绝对项Absolute value 绝对值Absolute variation 绝对变异Abstract number 抽象数Abstract unit 抽象单元Accelerated factor 加速系数,加速因子Accelerated life test 加速寿命试验Accelerated test 加速试验Acceleration 加速度Acceptable limit 允收边界Acceptable process 允收制程程度Acceptable quality 允收品质Acceptable quality level (AQL) 允收质量程度Acceptable reliability level (ARL) 允收可靠度程度Acceptability 允收性Acceptability criterion 允收尺度Acceptance 允收,验收Acceptance, probability of 允收机率Acceptance, region of 允收区域Acceptance and rejection criteria 允收与拒收准那么Acceptance boundary 允收边界Acceptance coefficient 允收系数Acceptance control chart 验收管制图Acceptance cost 验收费用Acceptance criteria 允收准那么Acceptance error 允收误差Acceptance inspection 验收查验Acceptance limit 允收边界Acceptance line 允收线Acceptance number 允收〔不良品〕数Acceptance plan 验收方案Acceptance procedure 验收程序Acceptance/rectification scheme 允收/精选方案Acceptance sampling, attribute 计数值验收抽样Acceptance sampling, variable 计量值验收抽样Acceptance sampling plan 验收抽样方案Acceptance sampling scheme 验收抽样方案Acceptance test 验收试验Acceptance value 允收值Acceptance zone 允收区域Acceptance product 允收品Accepting lot 允收批Access time 接近时间,故障诊断时间Accessibility 可接近性Accident rate 不测率Accidental error 偶误,偶然误差Accidental fluctuation 偶然波动Accidental movement 不测移动Accounting test 验算〔决算〕试验Accumulated operating time 累积操作时间Accuracy 准确度Accuracy of data 数据准确度Accuracy of estimation 估计准确度Accuracy of the mean 平均数准确度Achieved availability 实际可用度Action 步履,办法Action, corrective 矫正步履〔办法〕Action control chart 步履管制图Action limit 步履边界Active line 步履线Active maintenance time 实际维护时间Active parallel redundancy 主动并复联〔置〕Active preventive maintenance 现行预防维护时间Active redundancy 主动复联〔置〕Active repair time 实际修复时间Active standby 主动备用Active time 运用时间Actual frequency 实际次数Actual limit 实际边界Actual range 实际全距Actual value 实际值Adaptability 可适应性Adaptive control 点窜管制Addition theorem 加法定理Additivity 加法性,可加性Adjusted average 修正平均数Adjusted value 修正值Adjustment factor 调整系数Administration time for a repair 修复之办理时间Administrative time 办理时间Adopted value 采用值Advisory Group on Reliability of Electronic Equipment (AGREE) 电子装备可靠度参谋团Aeronautical Radio, Incorporated (ARINC) 航空无线电公司After-sales service 售后效劳Age 年限Age at death 死亡年限Age at failure 掉效年限Age-based maintenance 年限基准维护Aggregative method 综合法Aging 老化Agreement of quality assurance 质量包管之协议Agreement on verification method 验〔查〕证方法之协议Alarm signals 警告〔报〕讯号Alert time 待命时间Algebraic sum 代数和Algorism (Algorithm) 阿拉伯数字计数法Alias 假名Alienation 余相关Alignment chart 列线图Allocation 配当Allocation of reliability 可靠度配当Allowable percent defective (Acceptable quality level, AQL) 允收不良率〔允收质量程度〕Allowance 允差,裕度Alternative hypothesis 对立假设American Management Association (AMA) 美国办理协会American National Standards Institute (ANSI) 美国尺度协会American Society for Quality Control (ASQC) 美国质量办理学会American Society for Mechanical Engineers (ASME) 美国机械工程师学会American Society for Testing and Materials (ASTM) 美国材料试验学会American Standard Association (ASA) 美国尺度协会American Statistical Association (ASA) 美国统计协会American War Standards (AWS) 美国战时尺度Ambient condition 周遭条件Analysis, sequential 逐次阐发Analysis by accumulated frequency 累积法,累积次数阐发Analysis by non-accumulated frequency 次数法,非累积次数阐发Analysis of correlation 相关阐发Analysis of covariance 共变异数阐发Analysis of means (AVON) 平均数阐发Analysis of problem 问题之阐发Analysis of variance (ANOVA) 变异数阐发Analysis sample 阐发样本Analytical error 阐发误差Angular transformation 角度转〔变〕换Anti-logarithm 逆对数Anti-mode 逆众数AOQL Sampling Table 平均出厂质量边界抽样数Applicability 应用性Applied statistics 应用统计学Apportionment of reliability 可靠度配当Apportionment techniques 配当技术Appraisal cost 鉴定成本,评估成本Appraisal system 评估制度Appraisal of quality 质量评估Approach to sequential testing 逐次试验法Approval of processes and equipment 核准制程与设备Approximate mode 近似众数Approximate number 近似数值Approximation 近似法,概算AQL (Acceptable quality level) 允收〔质量〕程度Arbitrary average (Assumed average,Arbitrary mean) 假定平均数Arbitrary origin 假定原点Arbitrary scale 假定标度Area bar chart 面积条图Area chart (diagram, graph) 面积图Area sampling 地域抽样Arithmetic average 算术平均数Arithmetic cross 算术交叉Arithmetic graph 算术图Arithmetic line chart 算术线图Arithmetic mean 算术平均数Arithmetic paper 算术纸Arithmetic probability paper 算术机率纸Arithmetic progression (Arithmetic series) 算术级数,等差级数Arithmetic scale 算术标度,等差标度Arithmetic series 算术级数,等差级数Army Ordnance Table 陆军兵工署〔抽样〕表Army Service Forces Table 陆军〔抽样〕表序列Array 序列Array distribution 序列分配〔布〕Array of data 数据序列Assemble 装配〔组立〕Assembled product 装配品Assembly 装配件Assembly inspection 装配查验Assembly quality analysis report 装配质量阐发陈述Assessed failure rate 评估掉效率Assessed mean active -maintenance time 评估时间现行维护时间Assessed mean life 评估平均寿命Assessed mean time between failures 评估平均掉效间格时间Assessed mean time to failure 评估平均掉效前时间Assessed reliability 评估可靠度Assessed value 评估值Assessment of subcontractor 分包商之评鉴Assignable cause (Special cause) 非机遇原因〔特殊原因〕Assignable variation 非机遇变异Associated dependent variable 相联因变数Associated variate 相联变量Association coefficient 相联系数Association of attribute 品性相联Association table 相联表,联合表Assumed mean (Assumed average,Arbitrary average) 假定平均数Assumed median 假定中位数Assumed origin 假定原点Assurance quality 包管质量Assurance function 包管功能Asymmetrical distribution 不合错误称分配〔布〕Asymmetry 不合错误称Asymptotic distribution 趋近分配〔布)At random 随机Attribute 计数值,属性Attribute classification 品性分类Attribute data 计数数据Attribute inspection 计数值查验Attribute sampling 计数值抽样Attribute sampling plan 计数值抽样方案Attribute testing (Go no-go testing) 计数值试验〔通过与不通过试验〕Attribute value 计数值Audit 稽核Audit for reliability 可靠度稽核Audit of decision 稽核决策Audit plan 稽核方案Audit report 稽核陈述Auditing report 稽核陈述Auto-correlation 自动相关Automatic switch-over redundancy 自动切换复联〔置〕Automatic test equipment (Am) 自动试验装备Auto-regression 自动回归Availability 可用性,可用度Average (Mean) 平均数,平均值Average, grand 总平均Average, moving 移动平均数Average, sample 样本平均数Average, standard error of 尺度误平均数Average, universe 群体平均数Average, weighted 加权平均数Average amount of inspection 平均查验数Average and range chart 平均数及全距〔管制〕图Average availability 平均可用度Average deviation (A.D.) (Mean deviation) 平均差Average error (Mean error) 平均误差Average number of defects 平均错误谬误数Average of ratios 比例平均数Average outgoing quality (AOQ) 平均出厂质量Average outgoing quality curve 平均出厂质量曲线Average outgoing quality level 平均出厂质量程度Average outgoing quality limit (AOQL) 平均出厂程度Average quality level 平均出厂质量边界Average quality level line 质量平均线Average quality protection 平均质量庇护Average range 平均全距Average run length (ARL) 平均连串长度Average sample number (ASN) 平均样品数Average range 平均全距Average run length (ARL) 平均连串长度Average sample number(ASN) 平均样本数Average sample number curve 平均样本曲线Average sample size (ASS) 平均样本大小Average sample size curve 平均样本大小曲线Average sample 平均抽样Average total inspection (ATI) 平均总查验〔件〕数Average total inspection curve 平均总查验数曲线Average value 平均值Avoidable cause 可防止之原因Avoidable quality cost 可防止之质量成本Axiom 公理Axis 轴Axis of abscissa 横轴Axis of ordinate 纵轴BBad lot 坏批Balance frequency 平衡次数Balanced complete type 平衡完备型Balanced design 平衡设计Balanced experiment 平衡尝试Balanced incomplete type 平衡不完备型Balanced sample 平衡样本Band chart 带形图Band curve chart 带形曲线图Bank of reliability data 可靠度数据库Bar chart (diagram) 条〔形〕图Bartlett's test 巴特莱特试验Base line 基线Base number 基数Base period 基期Base point 基点Basic reliability 底子可靠度Batch (Lot) 批Batch of material 材料批Batch process 分批制造方法Batch size 批量Batch testing 批试验Bathtub curve 浴缸曲线Bathtub failure curve 浴缸掉效曲线Bayes' estimator 贝式估计式Bayes' theorem 贝式定理Bayesian approach 贝式法Bayesian approcah to design 贝式设计法Bayesian estimation 贝式估计Bead map 标珠图Bell-shaped curve 钟形曲线Bell-shaped distribution 钟形分配〔布〕Bell-shaped failure pattern 钟形掉效型态JBell System 贝尔系统Bell Telephone Laboratories 贝尔尝试室Bell Telephone Laboratories Sampling Table 贝尔〔尝试室〕抽样表Benign failure 无危险的掉效Bernoulli distribution 白努利分配〔布〕Best fit 最适配合Best fitting line 最适线Best fitting curve 最适曲线Best linear invariant estimator 最正确线型不变估计式Best linear unbiased estimator 最正确线型不偏估计式Beta coefficient β系数Beta distribution β分配〔布〕Beta function β函数Between-class variance 组间变异数Between-column variance 组间变异Between-column variation 行间变异Between-row variation 列间变异Between sample variation 样本间变异Bias 偏差Bias, downward 向下偏差Bias, downward type 向下型偏差Bias, upward 向上偏差Bias, upward type 向上型偏差Biased error 偏误Biased estimate 偏差估计Biased sample 偏差样本Biased test 偏差试验Bilateral 双边Bill of material (BOM) 物料清单Bimodal 双峰Bimodal curve 双峰曲线Bimodal distribution 双峰分配〔布〕Bimodal redundancy 双峰型复联〔置〕Bimodality 双峰性Binary system 二元制Binomial, skewed 偏态二项Binomial coefficient 二项系数Binomial curve 二项曲线Binomial distribution 二项分配〔布〕Binomial equation 二项方程式Binomial expansion 二项展开式Binomial population 二项群体Binomial probability distribution 二项机率分配〔布〕Binomial probability paper(BIPP) 二项机率纸Binomial series 二项级数Binomial theorem 二项定理Bi-serial 双数列Biserial correlation 双数列相关Biserial coefficient of correlation 双数列相关系数Biserial ratio of correlation 双数列相关比Bivariate 双变量Bivariate distribution 双变量分配〔布〕Bivariate frequency distribution 双变量次数分配〔布〕Bivariate normal distribution 双变量常态分配〔布〕Blend 混,混合Block 量块,〔尝试〕区,方块Block design 尝试区设计Block diagram 方块图Block factor 地域因素Block in series 串联方块Boundary 界Boundary, cell 组界Bowker-Goode variables plan Bowker-Goode 记量值〔抽样〕方案Bowl drawing 碗珠抽样Bowl experiment 碗珠尝试Bowl test 碗珠试验Bowley's coefficient of skewness Bowley偏态系数Bowley's formula Bowley公式Bureau of Ordnance, U.S. Navy 美国海军兵工署Break-even chart 损益平衡图Break-even point (BEP) 损益平衡点Breakthrough 冲破British Standards Institution 英国尺度协会Broken curve 中断曲线Broken series 中断数列Broken trend 中断趋势Built-in test (BIT) 内含测试,自测Bureau of Commodity Inspection and Quarantine (BCIQ) 商品查验局Bulk sampling Burn-in 大宗抽样Business Process Management (BPM) 业务流程办理Buyer 买方,客户CC chart C〔管制〕图Calculated value (Computed value) 计算值Calculation chart 计算图Calendar time 日历时间Calibration 校正Calibration record 校正记录Camp-Meidell inequality Camp-Meidell不等式Capability 能力Capability, machine 机器能力Capability, process 制程能力Capability ratio 能力比Capacity 能量,容量Caption 纵标目Carrying out the audit 实施稽核Cartogram 统计图Case method 个案法Catastrophic failure 俄然故障,崩坏掉效,致命掉效Category 类别Cauchy distribution Cauchy 分配〔布〕Causality 因果律Cause 原因Cause, assignable 非机遇原因Cause, avoidable 可防止原因Cause, chance 机遇原因Cause, common 共同原因Cause, findable 可寻找原因Cause, random 随机原因Cause, special 特殊原因Cause, substantial 本质原因Cause, unavoidable 不成防止原因Cause and effect 因果Cause and effect diagram 特性要因图Cell 组Cell boundary 组界Cell deviation (d) 组离差Cell frequency (f) 组次数Cell interval (i,h) 组距Cell limit 组限Cell method 分组法Cell mid-point (Xm) 组中点Cell value 组值Censored sample 检剔样本Censored test 检剔试验Censorship 检剔Census 普查Center line 中线Central inspection station 中央查验站Central limit theory 趋中理论,中央极限理论Central limit theorem 趋中理论,中央极限理论Central line (CL.) 中心线Central moment 中心动差Central ordinate 中纵坐标Central tendency 集中趋势Central value 中值,中心值Certainty 确定性Certified chart 验证图Certified equipment 合格设备Certified quality engineer (CQE) 合格质量工程师Certified quality technician (CQT) 合格质量技术师Certified reliability engineer (CRE) 合格可靠度工程师Certification 验证Chain model 炼结模型Chain reliability 炼结可靠度Chain sampling plan (CHSP) 炼结抽样方案Chance 机遇Chance cause 机遇原因Chance error (Probable error) 机遇误差,机误Chance factor 机遇因素Chance failure 机遇故障,机遇掉效Chance failure period 机遇掉效期Chance fluctuation 机遇波动Chance variable 机遇变数Chance variation 机遇变异Change control 改变〔变动〕办理Chaotic variation 混乱变异Characteristic 〔质量〕特性Characteristic, qualitative 质的特性Characteristic, quantitative 量的特性Characteristic curve, operating (OC curve) 操作特性曲线,OC曲线Characteristic diagram 特性要因图Characteristic function 特性函数Characteristic life 特性寿命Characteristic operating curve (OC curve) 特性操作曲线〔OC曲线〕Characteristic value 特性值Chargeable failure 可计列掉效,故障Charlier check Charlier 覆检法Chart 图,〔管制〕图Chart, acceptance control 验收管制图Chart, average and range 平均数及全距〔管制〕图Chart, average number of defects 平均错误谬误数〔管制〕图Chart, control 管制图Chart, cumulative sum 累积和〔管制〕图Chart, defects per unit 每单元内错误谬误数〔管制〕图Chart, fraction defective 不良率〔管制〕图Chart, group 多项〔管制)图Chart, individual 个别值〔管制〕图Chart, median 中位数〔管制〕图Chart, moving and range 移动平均数及全距〔管制〕图Chart, moving range 移动全距〔管制〕图Chart, modified control limits 修正管制边界〔管制〕图Chart, multi-variation 变异值〔管制〕图Chart, multiple 复式〔管制〕图Chart, number defectives 不良〔品〕数〔管制〕图Chart, number of defects 错误谬误数〔管制〕图Chart, percent defective 不良率管制图Chart, range 全距〔管制〕图Chart, run 操作〔记录〕图Chart, shop 工厂〔管制〕图Chart, Shewhart control Shewhart 管制图Chart, two-way control 双向管制图Chebyshev's inequality Chebyshev 不等式Check inspection 复核查验Check sampling 复核查验员Check inspector 复核抽样Chi-square ,卡方Chi-square distribution 分配〔布〕,卡方分配〔布〕Chi-square test 检定,卡方检定Chi-squared distribution 分配〔布〕,卡方分配(布〕Chip 小圆片Chronic defect 慢性错误谬误Chronological chart 时序图Chronological series 时序数列Class 组Class boundaries (True class limits)组界〔真实组限〕Class form 组形Class frequency (f) 组次数Class interval (i,h) 组距Class limit 组限Class mark 组标,中值Class mean 组平均数Class mid-point(Xm) 组中点Class mid-value 组中值Class of median 组中位数Class value 组值Classes, number of 组数Classification chart 分组,分类Classification frequency 分组次数Classification frequency series 分组次数数列Classification of defectives 不良品分类Classification of defects 错误谬误分类Classfication of failure 掉效分类,故障分类Classification process 分组〔方〕法Clearance 间隙,余隙Cluster 集团Cluster sampling 集团抽样Cochran's test Cochran 检定Code 简化,代号Code letter 代字Coded unit 简化单元Coded value 简化值Coding 简化Coding rule 简化规那么Coefficient 系数Coefficient, correlation 相关系数Coefficient of alienation 余相关系数Coefficient of association 相关系数Coefficient of binomial distribution 二项分配〔布〕系数Coefficient of colligation 束联系数Coefficient of contingency 列联系数Coefficient of correlation 相关系数Coefficient of determination (r2) 定限系数Coefficient of dispersion 离势系数Coefficient of kurtosis 峰度系数Coefficient of multiple correlation 复相关系数Coefficient of net correlation 净相关系数Coefficient of net regression 净回归系数Coefficient of non-determination 不定限系数Coefficient of part correlation 部份相关系数Coefficient of partial correlation 部份相关系数Coefficient of rank correlation 等级相关系数Coefficient of reliability 可靠度系数Coefficient of regression 回归系数Coefficient of skewness 偏态系数,偏斜系数Coefficient of variation (CV) 变异系数Cold standby 冷置系数Collective quality 集体品质Columbia sampling table Columbia 抽样方案Column (Column/Row) 行,纵行〔行/列〕Column head 标目Column diagram 直行图Combination 组合Combinational model 复合模型Combined environmental reliability test (CERT) 复合环境可靠度试验Combined failure 复合掉效,复合故障Combined stress life test 复合应力寿命试验Commissioning 委制Commodity 商品Common cause (Chance cause) 共同原因〔机遇原因〕Company standard 公司尺度Companys need 公司需要Company-wide quality control (CWQC) 全公司质量办理Comparability 可比性Comparable measure 可比量数Compensating error 抵偿误差Compensating fluctuation 抵偿波动Competing product 竞争产物Complete association 全相联Complete block design 完全区集法Complete confounding 完全交络Complete dissociation 全不相联Complete failure 完全故障,完全掉效Completely randomized design 完全随机法Complaint 抱怨Complaint index 抱怨指标Completed product verification 成品验证Component 组件,组件Component bar chart 成份条图Component distiibution 组成份分配〔布〕Component part diagram 成份图Component ratio 成份比Component reliability 组件可靠度Component variance 成份变异数Components of variance 变异数成份Composite curve 复合曲线Composite design 复合法Composite hypothesis 复合假设,组合假设Composite unit 复合单元Compound distribution 复合分配〔布〕Compound event 复合事件Compound probability 复合机率Compounding technique 复合法Compressed limit 压缩边界Compressed limit gauging 压缩边界规那么Computed value 计算值Concentric circle diagram 同心圆图Conception of limit 极限概念Conceptual design 概念设计Conceptual design review 概念设计审查Concession 特采,特认Concomitant factor 共变因素Concomitant variable 共变数Concomitant variation 共变异Concurrency 并行Condition maintenance 状态维护Condition monitoring 状态监督Condition-based maintenance 状态基准维护Conditional probability 条件机率Conditions of use 使用条件Confidence 信任,信赖Confidence coefficient 信任系数,信赖系数Confidence interval 信任区间,信赖区间Confidence in test results 试验成果的信赖度Confidence level 信任程度,信赖程度Confidence limit 信任边界,信赖边界Confidence range 信任全距,信赖全距Configuration control 型态管制Configuration items 型态件Configuration management 型态办理Confirmation 确认Conformance to the requirement 符合要求Conformation 一致Conforming article 合格品Conformity 符合Confounding 交络Confounding, complete 完全交络Confounding, partial 部份交络Connector 连接器Consignment 委托,寄售Consistency 一致性Constancy 长久性Constancy of great numbers 大数长久性Constant 常数Constant cause system 恒常原因系统Constant error 恒常误差Constant failure period 恒常掉效期Constant failure rate dustribution 恒常掉效率分配〔布〕Constant weight (Fixed weight) 固定权数Constraint 束缚Consultant 办理参谋师Consumer 消费者Consumer acceptance specification 消费者允收规格Consumerism 消费者主义Consumer's risk (CR) 消费者冒险率Consumer test panel 消费者试验小组Consumer preference 消费者偏好Consumer sensitivity test 消费者感官试验Contingency 列联Contingency coefficient 列联系数Contingency table 列联表Contingency theorem 列联理论Continuity correction 持续校正Continuous change 持续变动Continuous data 持续数据Continuous distribution 持续分配〔布〕Continuous production 持续出产Continuous sampling 持续抽样Continuous sampling plan (CSP) 持续抽样方案Continuous series 持续数列Continuous variable 持续变量Contract 合约Contract preparation 拟定合约Contract review 合约检讨Contract requirements 合约需求Contract requirements analysis 合约需求阐发Contractors 合约商Contrast analysis 对照阐发Control, in 在管制〔状态〕下Control, lack of 缺乏管制Control, out of 超出管制Control, state of 管制状态Control, under 在管制〔状态〕下Control chart 管制图Control chart, cumulative sum 累积和管制图Control chart, defects per unit 每单元内错误谬误数管制图Control chart, two-way 双向管制图Control chart factor 管制图系数Control chart for attribute 计数值管制图Control chart for variable (measurement) 计量值管制图Control chart method 管制图法Control chart pattern 管制图类型Control factor 管制因素Control gaging (gauging) 管制规测Control level 管制程度Control limit 管制边界Control limit, lower 管制下限Control limit, modified 修正管制边界Control limit, upper 管制上限Control limit factor 管制边界因子Control line 管制线Control of measuring and test equipment 量测与试验设备之管制Control of nonconforming material 不合格物料之管制Control of nonconforming product 不合格产物之管制Control of production 出产管制Control of reliability 可靠度管制Control of verification status 验证状况之管制Control plan 管制方案Control point 管制点Control station 管制站Control system 管制系统Controllability 可管制性Controlled process 管制制程Controlled state 管制状态Controlled variability 管制变异性Controlled variable 管制变数Controlling item 管制工程Convenience lot 合宜的批Convergence 收敛Cooked distribution 中断分配〔布〕Coordinate 坐标Coordinate axis 坐标轴Coordinate line 坐标线Coordination 协调Coordination for reliability 可靠度协调Correction 校正,修正Correction, Sheppard Sheppard 校正数Correction factor 修正因子Correction for continuity 持续校正Correction for mean 平均数校正Correction term 校正项Corrective action 矫正步履,改正办法Corrective maintenance 矫正维护,改正维护Corrective maintenance time 矫正维护时间,改正维护时间Corrective sorting 修正选别Correlated measure 相关量数Correlated samples 相关样本Correlation 相关Correlation, coefficient of 相关系数Correlation, direct 直接相关Correlation, index of 相关指数Correlation, inverse 反相关Correlation, multiple 复相关Correlation, negative 负相关Correlation, net 净相关Correlation, nonlinear 非线性相关Correlation, nonsense 无意义相关Correlation, part 部份相关,偏相关Correlation, partial 部份相关,偏相关Correlation, perfect 完全相关Correlation, rank 等级相关Correlation, serial 数序相关Correlation, simple 简相关Correlation, zero 零相关Correlation analysis 相关阐发Correlation chart 相关图Correlation, coefficient 相关系数Correlation coefficient, rank 等级相关系数Correlation matrix 相关矩阵Correlation of attributes 品性相关Correlation ratio 相关比Correlation of x on y x与y的相关比Correlation ratio of y on x y与x的相关比Correlation scatter chart 相关散布图Correlation surface 相关面Correlation table 相关表Correlation theory 相关理论Correlogram 相关图Corrosive atmosphere 腐蚀性空气Cost 成本,费用Cost, acquisition 取得成本Cost, appraisal 评估〔鉴定〕成本Cost, external failure 外部掉败成本Cost, internal failure 内部掉败成本Cost, life cycle 寿命周期成本Cost, logistic 后续成本Cost, prevention 预防成本Cost, quality 质量成本Cost, quality control 质量办理成本Cost, rework 重加工成本Cost effectiveness 成本效益Cost function 成本机能Cost model for reliability optimization 可靠度最正确化成本模式Cost reduction 成本减低Count (Countable) data 点计数据Counter variation 反行变异Co-variation 共变异Covariance 共变异数,共变数Covariance analysis 共变异数阐发Covariance matrix 共变异矩阵Craps, game of 掷骰游戏Credibility 信用Creep failure 潜变掉效,潜变故障Crest 峰Criteria for workmanship 工作技艺准那么Criterion 准那么,尺度Criterion, acceptance 验收准那么〔尺度〕Critical component control 重要组件管制Critical defect 严重错误谬误Critical defective 严重不良品Critical design review 关键设计审查Critical failure 关键故障,严重掉效Critical items 关键品目,重要件Critical path 要径Critical path analysis 要径阐发法Critical region 临界区域,弃却区域,判定区Critical value 临界值,判定值Criticality 严重性,关键性Cross 交叉Cross check 互校Cross classification 交叉分类Cross correlation 交叉相关Cross formula 交互公式Cross-hatch 交叉线Cross-hatched map 交叉图Cross-over design 交叉方案Crossed design 交叉法Crude mode 概括众数Crude moment 概括动差Cubic chart (diagram) 立方图Culled 检选Cumulant 累积数Cumulation, downward 向下累积Cumulation, total 全部累积Cumulation, upward 向上累积Cumulation average chart 累积平均数〔管制〕图Cumulative curve 累积曲线Cumulative curve chart 累积曲线图Cumulative damage 累积损坏Cumulative distribution (Ogive) 累积分配〔布〕Cumulative distribution function 累积分配〔布〕函数Cumulative error 累积误差Cumulative failure frequency 累积故障次数,累积掉效次数Cumulative frequency 累积次数Cumulative frequency arrangement 累积次数摆列Cumulative frequency curve 累积次数曲线Cumulative frequency 累积次数曲线图Cumulative frequency distribution 累积次数分配〔布〕Cumulative frequency polygon 累积〔次数〕多边形Cumulative frequency (probability) function 累积次数〔机率〕函数Cumulative frequency table 累积次数表Cumulative function 累积函数Cumulative graph 累积图Cumulative hazard function 累积冒险函数Cumulative mean 累积平均数Cumulative normal distribution 累积常态分配Cumulative number of failures 累积掉效数,累积故障数Cumulative percentage of failures 累积掉效百分率,累积故障百分率Cumulative probability distribution 累积机率分配〔布〕Cumulative sum 累积和Cumulative sum chart 累积和〔管制〕图Cumulative sum control chart 累积和管制图Cumulative terms 累积项Curtailed (Truncated) inspection 截略查验Curtailed (Truncated) sample inspection截略样品查验Curtailed sampling 截略抽样Curtailed sampling inspection 截略抽样查验Curtaijed sampling plan 截略抽样方案Curtailment of sampling plan 抽样方案之截略Curve 曲线Curve, frequency 次数曲线Curve, normal 常态曲线Curve chart (diagram) 曲线图Curve fitting 曲线配合Curve of error 误差曲线Curve of means 平均数曲线Curve of probability 机率曲线Curve type criterion 曲线型准那么Curve shape 曲线形状Curvilinear correlation 曲线相关Curvilinear regression 曲线回归Curvilinear trend 曲线趋势Curvilinearity 曲线性Customer 客户,顾客Customer complaint 顾客抱怨Customer feedback information 顾客回馈信息Customer incurred cost 顾客引发成本Customer operation cost 顾客作业成本Customer repair cost 顾客补缀成本Customer requirement 顾客要求Customer satisfaction 顾客对劲度Customer's need 顾客需要Cusum chart 累积和〔管制〕图Cycles 周期Cycles between failures 掉效间隔周期,故障间隔周期Cycle of operation 操作周期Cyclic curve 周期〔循环〕曲线Cyclic damage 周期性损坏Cyclic load 周期性负荷Cyclical deviation 周期〔循环〕离差Cyclical fluctuation 周期波动Cyclical trend 周期趋势Cyclical movement 周期移动Cyclical variation 周期变异Cycling failure rate 周期性掉效率,周期性故障率DD chart d管制图Data 数据Data analysis 数据阐发Data bank 资料室〔库〕Data exchange program 数据交换方案Data, inspection 查验数据Data item 数据项,文件工程Data processing 数据措置Death rate 死亡率Debug (debugging) 除错Decile 十分位数Decimal fraction 小数Decision function 决策函数Decision line 决定线Decision making 决策Decision variable 决策变数Decreasing failure rate distribution 递减掉效率分配(布〕Decrement 减量Decrement rate 减率Defect 疵病,错误谬误Defect, chronic 慢性错误谬误Defect, critical 严重错误谬误Defect, incidental 偶发错误谬误Defect, major 主要错误谬误Defect, minor 次要错误谬误Defect, sporadic 突发错误谬误Defect and failure analysis 错误谬误与掉效阐发Defect chart 错误谬误数〔管制〕图Defect Free 零错误谬误Defect prevention 错误谬误预防Defects, number of 错误谬误数Defects classification 错误谬误分类Defects per hundred units (dphu) 百件错误谬误数Defects per unit chart 每单元〔内〕错误谬误数〔管制〕图Defects per unit plan 每单元〔内〕错误谬误数〔管制〕方案Defective 不良品Defective, fraction 不良率Defective chart 不良品数〔管制〕图Defective material 不良材料Defective number 不良品数Defective part 不良零件Defective parts, percentage of 不良零件百分率Defective prevention 不良品预防Defective unit 不良品〔单元〕Defectives, number of 不良〔品〕数Defectives classification 不良品分类Definition(s) 定义Deflated series 调节数列Deflated value 调节值Deflating index 调节指数Degradation 劣化Degradation failure 劣化故障,劣化掉效Degree of accuracy 准确度Degree of approximation 近似度Degree of association 相联度Degree of confidence 信任〔赖〕度Degree of contribution 奉献度Degree of freedom (DF) 自由度Degree of reliability 可靠度Delivery 交货,出厂Delivery inspection 出厂查验Delivery qulaity 出厂品质Delivery time 运送时间Demerit 减点Demerit chart 减点〔数〕〔管制〕图Demerit rating 减点评比Demerits per unit 每单元〔内〕减点数Demonstration 示范,验证,展现Demonstration test 验证试验,展现试验Density function 密度函数Dependability 可恃性,相依性,依赖性Dependent factor 因变因子Dependent failure 相依掉效,相依故障Dependent variable 因变数Derating 降等,额降,减额定Derivation 导出Derived table 导出表Descriptive item 说明项Descriptive statistics 记述统计〔学〕Design 设计Design baseline 设计准那么Design change 设计变动Design considerations 设计考虑Design control 设计管制Design change control 设计变动管制Design control, new 新设计管制Design criterion 设计准那么Design disclosure package 设计启导文件Design effect cost 设计效应成本Design freeze 设计冻结Design in 设计进去Design input 设计输入Design matrix 设计矩阵Design output 设计输出Design of experiment 尝试方案Design planning 设计规画Design profile 设计轮廓Design proving 设计承认Design qualification 设计之合格性Design release 设计发布Design requalification 设计合格之再认定Design review 设计审查Design specification 设计规格Design validation 设计确认Design verification 设计验证,查证Design verification test 设计验证试验。

质量英语词汇大全

质量英语词汇大全

质量英语词汇大全AABC analysis ABC 分析Abnormality 不正常性Abscissa 横坐标Absolute deviation 绝对离差Absolute dispersion 绝对离势Absolute error 绝对误差Absolute frequency 绝对次数Absolute number 绝对数Absolute reliability 绝对可靠度Absolute term 绝对项Absolute value 绝对值Absolute variation 绝对变异Abstract number 抽象数Abstract unit 抽象单位Accelerated factor 加速系数,加速因子Accelerated life test 加速寿命试验Accelerated test 加速试验Acceleration 加速度Acceptable limit 允收界限Acceptable process 允收制程水平Acceptable quality 允收品质Acceptable quality level (AQL) 允收质量水平Acceptable reliability level (ARL) 允收可靠度水平Acceptability 允收性Acceptability criterion 允收标准Acceptance 允收,验收Acceptance, probability of 允收机率Acceptance, region of 允收区域Acceptance and rejection criteria 允收与拒收准则Acceptance boundary 允收界限Acceptance coefficient 允收系数Acceptance control chart 验收管制图Acceptance cost 验收费用Acceptance criteria 允收准则Acceptance error 允收误差Acceptance inspection 验收检验Acceptance limit 允收界限Acceptance line 允收线Acceptance number 允收(不良品)数Acceptance plan 验收打算Acceptance procedure 验收程序Acceptance/rectification scheme 允收/精选方案Acceptance sampling, attribute 计数值验收抽样Acceptance sampling, variable 计量值验收抽样Acceptance sampling plan 验收抽样打算Acceptance sampling scheme 验收抽样方案Acceptance test 验收试验Acceptance value 允收值Acceptance zone 允收区域Acceptance product 允收品Accepting lot 允收批Access time 接近时刻,故障诊断时刻Accessibility 可接近性Accident rate 意外率Accidental error 偶误,偶然误差Accidental fluctuation 偶然波动Accidental movement 意外移动Accounting test 验算(决算)试验Accumulated operating time 累积操作时刻Accuracy 准确度Accuracy of data 数据准确度Accuracy of estimation 估量准确度Accuracy of the mean 平均数准确度Achieved availability 实际可用度Action 行动,措施Action, corrective 矫正行动(措施)Action control chart 行动管制图Action limit 行动界限Active line 行动线Active maintenance time 实际爱护时刻Active parallel redundancy 主动并复联(置)Active preventive maintenance 现行预防爱护时刻Active redundancy 主动复联(置)Active repair time 实际修复时刻Active standby 主动备用Active time 运用时刻Actual frequency 实际次数Actual limit 实际界限Actual range 实际全距Actual value 实际值Adaptability 可适应性Adaptive control 修改管制Addition theorem 加法定理Additivity 加法性,可加性Adjusted average 修正平均数Adjusted value 修正值Adjustment factor 调整系数Administration time for a repair 修复之治理时刻Administrative time 治理时刻Adopted value 采纳值Advisory Group on Reliability of Electronic Equipment (AGREE) 电子装备可靠度顾问团Aeronautical Radio, Incorporated (ARINC) 航空无线电公司After-sales service 售后服务Age 年限Age at death 死亡年限Age at failure 失效年限Age-based maintenance 年限基准爱护Aggregative method 综合法Aging 老化Agreement of quality assurance 质量保证之协议Agreement on verification method 验(查)证方法之协议Alarm signals 警告(报)讯号Alert time 待命时刻Algebraic sum 代数和Algorism (Algorithm) 阿拉伯数字计数法Alias 假名Alienation 余相关Alignment chart 列线图Allocation 配当Allocation of reliability 可靠度配当Allowable percent defective (Acceptable quality level, AQL) 允收不良率(允收质量水平)Allowance 允差,裕度Alternative hypothesis 对立假设American Management Association (AMA) 美国治理协会American National Standards Institute (ANSI) 美国标准协会American Society for Quality Control (ASQC) 美国质量治理学会American Society for Mechanical Engineers (ASME) 美国机械工程师学会American Society for Testing and Materials (ASTM) 美国材料试验学会American Standard Association (ASA) 美国标准协会American Statistical Association (ASA) 美国统计协会American War Standards (AWS) 美国战时标准Ambient condition 周遭条件Analysis, sequential 逐次分析Analysis by accumulated frequency 累积法,累积次数分析Analysis by non-accumulated frequency 次数法,非累积次数分析Analysis of correlation 相关分析Analysis of covariance 共变异数分析Analysis of means (AVON) 平均数分析Analysis of problem 问题之分析Analysis of variance (ANOVA) 变异数分析Analysis sample 分析样本Analytical error 分析误差Angular transformation 角度转(变)换Anti-logarithm 逆对数Anti-mode 逆众数AOQL Sampling Table 平均出厂质量界限抽样数Applicability 应用性Applied statistics 应用统计学Apportionment of reliability 可靠度配当Apportionment techniques 配当技术Appraisal cost 鉴定成本,评估成本Appraisal system 评估制度Appraisal of quality 质量评估Approach to sequential testing 逐次试验法Approval of processes and equipment 核准制程与设备Approximate mode 近似众数Approximate number 近似数值Approximation 近似法,概算AQL (Acceptable quality level) 允收(质量)水平Arbitrary average (Assumed average,Arbitrary mean) 假定平均数Arbitrary origin 假定原点Arbitrary scale 假定标度Area bar chart 面积条图Area chart (diagram, graph) 面积图Area sampling 地区抽样Arithmetic average 算术平均数Arithmetic cross 算术交叉Arithmetic graph 算术图Arithmetic line chart 算术线图Arithmetic mean 算术平均数Arithmetic paper 算术纸Arithmetic probability paper 算术机率纸Arithmetic progression (Arithmetic series) 算术级数,等差级数Arithmetic scale 算术标度,等差标度Arithmetic series 算术级数,等差级数Army Ordnance Table 陆军兵工署(抽样)表Army Service Forces Table 陆军(抽样)表序列Array 序列Array distribution 序列分配(布)Array of data 数据序列Assemble 装配(组立)Assembled product 装配品Assembly 装配件Assembly inspection 装配检验Assembly quality analysis report 装配质量分析报告Assessed failure rate 评估失效率Assessed mean active -maintenance time 评估时刻现行爱护时刻Assessed mean life 评估平均寿命Assessed mean time between failures 评估平均失效间格时刻Assessed mean time to failure 评估平均失效前时刻Assessed reliability 评估可靠度Assessed value 评估值Assessment of subcontractor 分包商之评鉴Assignable cause (Special cause) 非机遇缘故(专门缘故)Assignable variation 非机遇变异Associated dependent variable 相联因变数Associated variate 相联变量Association coefficient 相联系数Association of attribute 品性相联Association table 相联表,联合表Assumed mean (Assumed average,Arbitrary average) 假定平均数Assumed median 假定中位数Assumed origin 假定原点Assurance quality 保证质量Assurance function 保证功能Asymmetrical distribution 不对称分配(布)Asymmetry 不对称Asymptotic distribution 趋近分配(布)At random 随机Attribute 计数值,属性Attribute classification 品性分类Attribute data 计数数据Attribute inspection 计数值检验Attribute sampling 计数值抽样Attribute sampling plan 计数值抽样打算Attribute testing (Go no-go testing) 计数值试验(通过与不通过试验)Attribute value 计数值Audit 稽核Audit for reliability 可靠度稽核Audit of decision 稽核决策Audit plan 稽核打算Audit report 稽核报告Auditing report 稽核报告Auto-correlation 自动相关Automatic switch-over redundancy 自动切换复联(置)Automatic test equipment (Am) 自动试验装备Auto-regression 自动回来Availability 可用性,可用度Average (Mean) 平均数,平均值Average, grand 总平均Average, moving 移动平均数Average, sample 样本平均数Average, standard error of 标准误平均数Average, universe 群体平均数Average, weighted 加权平均数Average amount of inspection 平均检验数Average and range chart 平均数及全距(管制)图Average availability 平均可用度Average deviation (A.D.) (Mean deviation) 平均差Average error (Mean error) 平均误差Average number of defects 平均缺点数Average of ratios 比例平均数Average outgoing quality (AOQ) 平均出厂质量Average outgoing quality curve 平均出厂质量曲线Average outgoing quality level 平均出厂质量水平Average outgoing quality limit (AOQL) 平均出厂水平Average quality level 平均出厂质量界限Average quality level line 质量平均线Average quality protection 平均质量爱护Average range 平均全距Average run length (ARL) 平均连串长度Average sample number (ASN) 平均样品数Average range 平均全距Average run length (ARL) 平均连串长度Average sample number(ASN) 平均样本数Average sample number curve 平均样本曲线Average sample size (ASS) 平均样本大小Average sample size curve 平均样本大小曲线Average sample 平均抽样Average total inspection (ATI) 平均总检验(件)数Average total inspection curve 平均总检验数曲线Average value 平均值Avoidable cause 可幸免之缘故Avoidable quality cost 可幸免之质量成本Axiom 公理Axis 轴Axis of abscissa 横轴Axis of ordinate 纵轴BBad lot 坏批Balance frequency 平稳次数Balanced complete type 平稳完备型Balanced design 平稳设计Balanced experiment 平稳实验Balanced incomplete type 平稳不完备型Balanced sample 平稳样本Band chart 带形图Band curve chart 带形曲线图Bank of reliability data 可靠度数据库Bar chart (diagram) 条(形)图Bartlett's test 巴特莱特试验Base line 基线Base number 基数Base period 基期Base point 基点Basic reliability 差不多可靠度Batch (Lot) 批Batch of material 材料批Batch process 分批制造方法Batch size 批量Batch testing 批试验Bathtub curve 浴缸曲线Bathtub failure curve 浴缸失效曲线Bayes' estimator 贝式估量式Bayes' theorem 贝式定理Bayesian approach 贝式法Bayesian approcah to design 贝式设计法Bayesian estimation 贝式估量Bead map 标珠图Bell-shaped curve 钟形曲线Bell-shaped distribution 钟形分配(布)Bell-shaped failure pattern 钟形失效型态JBell System 贝尔系统Bell Telephone Laboratories 贝尔实验室Bell Telephone Laboratories Sampling Table 贝尔(实验室)抽样表Benign failure 无危险的失效Bernoulli distribution 白努利分配(布)Best fit 最适配合Best fitting line 最适线Best fitting curve 最适曲线Best linear invariant estimator 最佳线型不变估量式Best linear unbiased estimator 最佳线型不偏估量式Beta coefficient β系数Beta distribution β分配(布)Beta function β函数Between-class variance 组间变异数Between-column variance 组间变异Between-column variation 行间变异Between-row variation 列间变异Between sample variation 样本间变异Bias 偏差Bias, downward 向下偏差Bias, downward type 向下型偏差Bias, upward 向上偏差Bias, upward type 向上型偏差Biased error 偏误Biased estimate 偏差估量Biased sample 偏差样本Biased test 偏差试验Bilateral 双边Bill of material (BOM) 物料清单Bimodal 双峰Bimodal curve 双峰曲线Bimodal distribution 双峰分配(布)Bimodal redundancy 双峰型复联(置)Bimodality 双峰性Binary system 二元制Binomial, skewed 偏态二项Binomial coefficient 二项系数Binomial curve 二项曲线Binomial distribution 二项分配(布)Binomial equation 二项方程式Binomial expansion 二项展开式Binomial population 二项群体Binomial probability distribution 二项机率分配(布)Binomial probability paper(BIPP) 二项机率纸Binomial series 二项级数Binomial theorem 二项定理Bi-serial 双数列Biserial correlation 双数列相关Biserial coefficient of correlation 双数列相关系数Biserial ratio of correlation 双数列相关比Bivariate 双变量Bivariate distribution 双变量分配(布)Bivariate frequency distribution 双变量次数分配(布)Bivariate normal distribution 双变量常态分配(布)Blend 混,混合Block 量块,(实验)区,方块Block design 实验区设计Block diagram 方块图Block factor 地区因素Block in series 串联方块Boundary 界Boundary, cell 组界Bowker-Goode variables plan Bowker-Goode 记量值(抽样)打算Bowl drawing 碗珠抽样Bowl experiment 碗珠实验Bowl test 碗珠试验Bowley's coefficient of skewness Bowley偏态系数Bowley's formula Bowley公式Bureau of Ordnance, U.S. Navy 美国海军兵工署Break-even chart 损益平稳图Break-even point (BEP) 损益平稳点Breakthrough 突破British Standards Institution 英国标准协会Broken curve 中断曲线Broken series 中断数列Broken trend 中断趋势Built-in test (BIT) 内含测试,自测Bureau of Commodity Inspection and Quarantine (BCIQ) 商品检验局Bulk sampling Burn-in 大宗抽样Business Process Management (BPM) 业务流程治理Buyer 买方,客户CC chart C(管制)图Calculated value (Computed value) 运算值Calculation chart 运算图Calendar time 日历时刻Calibration 校正Calibration record 校正记录Camp-Meidell inequality Camp-Meidell不等式Capability 能力Capability, machine 机器能力Capability, process 制程能力Capability ratio 能力比Capacity 能量,容量Caption 纵标目Carrying out the audit 实施稽核Cartogram 统计图Case method 个案法Catastrophic failure 突然故障,崩坏失效,致命失效Category 类别Cauchy distribution Cauchy 分配(布)Causality 因果律Cause 缘故Cause, assignable 非机遇缘故Cause, avoidable 可幸免缘故Cause, chance 机遇缘故Cause, common 共同缘故Cause, findable 可查找缘故Cause, random 随机缘故Cause, special 专门缘故Cause, substantial 本质缘故Cause, unavoidable 不可幸免缘故Cause and effect 因果Cause and effect diagram 特性要因图Cell 组Cell boundary 组界Cell deviation (d) 组离差Cell frequency (f) 组次数Cell interval (i,h) 组距Cell limit 组限Cell method 分组法Cell mid-point (Xm) 组中点Cell value 组值Censored sample 检剔样本Censored test 检剔试验Censorship 检剔Census 普查Center line 中线Central inspection station 中央检验站Central limit theory 趋中理论,中央极限理论Central limit theorem 趋中理论,中央极限理论Central line (CL.) 中心线Central moment 中心动差Central ordinate 中纵坐标Central tendency 集中趋势Central value 中值,中心值Certainty 确定性Certified chart 验证图Certified equipment 合格设备Certified quality engineer (CQE) 合格质量工程师Certified quality technician (CQT) 合格质量技术师Certified reliability engineer (CRE) 合格可靠度工程师Certification 验证Chain model 炼结模型Chain reliability 炼结可靠度Chain sampling plan (CHSP) 炼结抽样打算Chance 机遇Chance cause 机遇缘故Chance error (Probable error) 机遇误差,机误Chance factor 机遇因素Chance failure 机遇故障,机遇失效Chance failure period 机遇失效期Chance fluctuation 机遇波动Chance variable 机遇变数Chance variation 机遇变异Change control 改变(变更)治理Chaotic variation 纷乱变异Characteristic (质量)特性Characteristic, qualitative 质的特性Characteristic, quantitative 量的特性Characteristic curve, operating (OC curve) 操作特性曲线,OC曲线Characteristic diagram 特性要因图Characteristic function 特性函数Characteristic life 特性寿命Characteristic operating curve (OC curve) 特性操作曲线(OC曲线)Characteristic value 特性值Chargeable failure 可计列失效,故障Charlier check Charlier 覆检法Chart 图,(管制)图Chart, acceptance control 验收管制图Chart, average and range 平均数及全距(管制)图Chart, average number of defects 平均缺点数(管制)图Chart, control 管制图Chart, cumulative sum 累积和(管制)图Chart, defects per unit 每单位内缺点数(管制)图Chart, fraction defective 不良率(管制)图Chart, group 多项(管制)图Chart, individual 个别值(管制)图Chart, median 中位数(管制)图Chart, moving and range 移动平均数及全距(管制)图Chart, moving range 移动全距(管制)图Chart, modified control limits 修正管制界限(管制)图Chart, multi-variation 变异值(管制)图Chart, multiple 复式(管制)图Chart, number defectives 不良(品)数(管制)图Chart, number of defects 缺点数(管制)图Chart, percent defective 不良率管制图Chart, range 全距(管制)图Chart, run 操作(记录)图Chart, shop 工厂(管制)图Chart, Shewhart control Shewhart 管制图Chart, two-way control 双向管制图Chebyshev's inequality Chebyshev 不等式Check inspection 复核检验Check sampling 复核检验员Check inspector 复核抽样Chi-square ,卡方Chi-square distribution 分配(布),卡方分配(布)Chi-square test 检定,卡方检定Chi-squared distribution 分配(布),卡方分配(布)Chip 小圆片Chronic defect 慢性缺点Chronological chart 时序图Chronological series 时序数列Class 组Class boundaries (True class limits)组界(真实组限)Class form 组形Class frequency (f) 组次数Class interval (i,h) 组距Class limit 组限Class mark 组标,中值Class mean 组平均数Class mid-point(Xm) 组中点Class mid-value 组中值Class of median 组中位数Class value 组值Classes, number of 组数Classification chart 分组,分类Classification frequency 分组次数Classification frequency series 分组次数数列Classification of defectives 不良品分类Classification of defects 缺点分类Classfication of failure 失效分类,故障分类Classification process 分组(方)法Clearance 间隙,余隙Cluster 集团Cluster sampling 集团抽样Cochran's test Cochran 检定Code 简化,代号Code letter 代字Coded unit 简化单位Coded value 简化值Coding 简化Coding rule 简化规则Coefficient 系数Coefficient, correlation 相关系数Coefficient of alienation 余相关系数Coefficient of association 相关系数Coefficient of binomial distribution 二项分配(布)系数Coefficient of colligation 束联系数Coefficient of contingency 列联系数Coefficient of correlation 相关系数Coefficient of determination (r2) 定限系数Coefficient of dispersion 离势系数Coefficient of kurtosis 峰度系数Coefficient of multiple correlation 复相关系数Coefficient of net correlation 净相关系数Coefficient of net regression 净回来系数Coefficient of non-determination 不定限系数Coefficient of part correlation 部份相关系数Coefficient of partial correlation 部份相关系数Coefficient of rank correlation 等级相关系数Coefficient of reliability 可靠度系数Coefficient of regression 回来系数Coefficient of skewness 偏态系数,偏斜系数Coefficient of variation (CV) 变异系数Cold standby 冷置系数Collective quality 集体品质Columbia sampling table Columbia 抽样打算Column (Column/Row) 行,纵行(行/列)Column head 标目Column diagram 直行图Combination 组合Combinational model 复合模型Combined environmental reliability test (CERT) 复合环境可靠度试验Combined failure 复合失效,复合故障Combined stress life test 复合应力寿命试验Commissioning 委制Commodity 商品Common cause (Chance cause) 共同缘故(机遇缘故)Company standard 公司标准Companys need 公司需要Company-wide quality control (CWQC) 全公司质量治理Comparability 可比性Comparable measure 可比量数Compensating error 补偿误差Compensating fluctuation 补偿波动Competing product 竞争产品Complete association 全相联Complete block design 完全区集法Complete confounding 完全交络Complete dissociation 全不相联Complete failure 完全故障,完全失效Completely randomized design 完全随机法Complaint 埋怨Complaint index 埋怨指标Completed product verification 成品验证Component 组件,组件Component bar chart 成份条图Component distiibution 组成份分配(布)Component part diagram 成份图Component ratio 成份比Component reliability 组件可靠度Component variance 成份变异数Components of variance 变异数成份Composite curve 复合曲线Composite design 复合法Composite hypothesis 复合假设,组合假设Composite unit 复合单位Compound distribution 复合分配(布)Compound event 复合事件Compound probability 复合机率Compounding technique 复合法Compressed limit 压缩界限Compressed limit gauging 压缩界限规则Computed value 运算值Concentric circle diagram 同心圆图Conception of limit 极限概念Conceptual design 概念设计Conceptual design review 概念设计审查Concession 特采,特认Concomitant factor 共变因素Concomitant variable 共变数Concomitant variation 共变异Concurrency 并行Condition maintenance 状态爱护Condition monitoring 状态监督Condition-based maintenance 状态基准爱护Conditional probability 条件机率Conditions of use 使用条件Confidence 信任,信任Confidence coefficient 信任系数,信任系数Confidence interval 信任区间,信任区间Confidence in test results 试验结果的信任度Confidence level 信任水平,信任水平Confidence limit 信任界限,信任界限Confidence range 信任全距,信任全距Configuration control 型态管制Configuration items 型态件Configuration management 型态治理Confirmation 确认Conformance to the requirement 符合要求Conformation 一致Conforming article 合格品Conformity 符合Confounding 交络Confounding, complete 完全交络Confounding, partial 部份交络Connector 连接器Consignment 托付,寄售Consistency 一致性Constancy 恒久性Constancy of great numbers 大数恒久性Constant 常数Constant cause system 恒常缘故系统Constant error 恒常误差Constant failure period 恒常失效期Constant failure rate dustribution 恒常失效率分配(布)Constant weight (Fixed weight) 固定权数Constraint 束缚Consultant 治理顾问师Consumer 消费者Consumer acceptance specification 消费者允收规格Consumerism 消费者主义Consumer's risk (CR) 消费者冒险率Consumer test panel 消费者试验小组Consumer preference 消费者偏好Consumer sensitivity test 消费者感官试验Contingency 列联Contingency coefficient 列联系数Contingency table 列联表Contingency theorem 列联理论Continuity correction 连续校正Continuous change 连续变更Continuous data 连续数据Continuous distribution 连续分配(布)Continuous production 连续生产Continuous sampling 连续抽样Continuous sampling plan (CSP) 连续抽样打算Continuous series 连续数列Continuous variable 连续变量Contract 合约Contract preparation 拟定合约Contract review 合约检讨Contract requirements 合约需求Contract requirements analysis 合约需求分析Contractors 合约商Contrast analysis 对比分析Control, in 在管制(状态)下Control, lack of 缺乏管制Control, out of 超出管制Control, state of 管制状态Control, under 在管制(状态)下Control chart 管制图Control chart, cumulative sum 累积和管制图Control chart, defects per unit 每单位内缺点数管制图Control chart, two-way 双向管制图Control chart factor 管制图系数Control chart for attribute 计数值管制图Control chart for variable (measurement) 计量值管制图Control chart method 管制图法Control chart pattern 管制图类型Control factor 管制因素Control gaging (gauging) 管制规测Control level 管制水平Control limit 管制界限Control limit, lower 管制下限Control limit, modified 修正管制界限Control limit, upper 管制上限Control limit factor 管制界限因子Control line 管制线Control of measuring and test equipment 量测与试验设备之管制Control of nonconforming material 不合格物料之管制Control of nonconforming product 不合格产品之管制Control of production 生产管制Control of reliability 可靠度管制Control of verification status 验证状况之管制Control plan 管制打算Control point 管制点Control station 管制站Control system 管制系统Controllability 可管制性Controlled process 管制制程Controlled state 管制状态Controlled variability 管制变异性Controlled variable 管制变数Controlling item 管制项目Convenience lot 合宜的批Convergence 收敛Cooked distribution 中断分配(布)Coordinate 坐标Coordinate axis 坐标轴Coordinate line 坐标线Coordination 和谐Coordination for reliability 可靠度和谐Correction 校正,修正Correction, Sheppard Sheppard 校正数Correction factor 修正因子Correction for continuity 连续校正Correction for mean 平均数校正Correction term 校正项Corrective action 矫正行动,改正措施Corrective maintenance 矫正爱护,改正爱护Corrective maintenance time 矫正爱护时刻,改正爱护时刻Corrective sorting 修正选别Correlated measure 相关量数Correlated samples 相关样本Correlation 相关Correlation, coefficient of 相关系数Correlation, direct 直截了当相关Correlation, index of 相关指数Correlation, inverse 反相关Correlation, multiple 复相关Correlation, negative 负相关Correlation, net 净相关Correlation, nonlinear 非线性相关Correlation, nonsense 无意义相关Correlation, part 部份相关,偏相关Correlation, partial 部份相关,偏相关Correlation, perfect 完全相关Correlation, rank 等级相关Correlation, serial 数序相关Correlation, simple 简相关Correlation, zero 零相关Correlation analysis 相关分析Correlation chart 相关图Correlation, coefficient 相关系数Correlation coefficient, rank 等级相关系数Correlation matrix 相关矩阵Correlation of attributes 品性相关Correlation ratio 相关比Correlation of x on y x与y的相关比Correlation ratio of y on x y与x的相关比Correlation scatter chart 相关散布图Correlation surface 相关面Correlation table 相关表Correlation theory 相关理论Correlogram 相关图Corrosive atmosphere 腐蚀性空气Cost 成本,费用Cost, acquisition 取得成本Cost, appraisal 评估(鉴定)成本Cost, external failure 外部失败成本Cost, internal failure 内部失败成本Cost, life cycle 寿命周期成本Cost, logistic 后续成本Cost, prevention 预防成本Cost, quality 质量成本Cost, quality control 质量治理成本Cost, rework 重加工成本Cost effectiveness 成本效益Cost function 成本机能Cost model for reliability optimization 可靠度最佳化成本模式Cost reduction 成本减低Count (Countable) data 点计数据Counter variation 反行变异Co-variation 共变异Covariance 共变异数,共变数Covariance analysis 共变异数分析Covariance matrix 共变异矩阵Craps, game of 掷骰游戏Credibility 信用Creep failure 潜变失效,潜变故障Crest 峰Criteria for workmanship 工作技艺准则Criterion 准则,规范Criterion, acceptance 验收准则(规范)Critical component control 重要组件管制Critical defect 严峻缺点Critical defective 严峻不良品Critical design review 关键设计审查Critical failure 关键故障,严峻失效Critical items 关键品目,重要件Critical path 要径Critical path analysis 要径分析法Critical region 临界区域,弃却区域,判定区Critical value 临界值,判定值Criticality 严峻性,关键性Cross 交叉Cross check 互校Cross classification 交叉分类Cross correlation 交叉相关Cross formula 交互公式Cross-hatch 交叉线Cross-hatched map 交叉图Cross-over design 交叉打算Crossed design 交叉法Crude mode 概括众数Crude moment 概括动差Cubic chart (diagram) 立方图Culled 检选Cumulant 累积数Cumulation, downward 向下累积Cumulation, total 全部累积Cumulation, upward 向上累积Cumulation average chart 累积平均数(管制)图Cumulative curve 累积曲线Cumulative curve chart 累积曲线图Cumulative damage 累积损坏Cumulative distribution (Ogive) 累积分配(布)Cumulative distribution function 累积分配(布)函数Cumulative error 累积误差Cumulative failure frequency 累积故障次数,累积失效次数Cumulative frequency 累积次数Cumulative frequency arrangement 累积次数排列Cumulative frequency curve 累积次数曲线Cumulative frequency 累积次数曲线图Cumulative frequency distribution 累积次数分配(布)Cumulative frequency polygon 累积(次数)多边形Cumulative frequency (probability) function 累积次数(机率)函数Cumulative frequency table 累积次数表Cumulative function 累积函数Cumulative graph 累积图Cumulative hazard function 累积冒险函数Cumulative mean 累积平均数Cumulative normal distribution 累积常态分配Cumulative number of failures 累积失效数,累积故障数Cumulative percentage of failures 累积失效百分率,累积故障百分率Cumulative probability distribution 累积机率分配(布)Cumulative sum 累积和Cumulative sum chart 累积和(管制)图Cumulative sum control chart 累积和管制图Cumulative terms 累积项Curtailed (Truncated) inspection 截略检验Curtailed (Truncated) sample inspection截略样品检验Curtailed sampling 截略抽样Curtailed sampling inspection 截略抽样检验Curtaijed sampling plan 截略抽样打算Curtailment of sampling plan 抽样打算之截略Curve 曲线Curve, frequency 次数曲线Curve, normal 常态曲线Curve chart (diagram) 曲线图Curve fitting 曲线配合Curve of error 误差曲线Curve of means 平均数曲线Curve of probability 机率曲线Curve type criterion 曲线型准则Curve shape 曲线形状Curvilinear correlation 曲线相关Curvilinear regression 曲线回来Curvilinear trend 曲线趋势Curvilinearity 曲线性Customer 客户,顾客Customer complaint 顾客埋怨Customer feedback information 顾客回馈信息Customer incurred cost 顾客引发成本Customer operation cost 顾客作业成本Customer repair cost 顾客修理成本Customer requirement 顾客要求Customer satisfaction 顾客中意度Customer's need 顾客需要Cusum chart 累积和(管制)图Cycles 周期Cycles between failures 失效间隔周期,故障间隔周期Cycle of operation 操作周期Cyclic curve 周期(循环)曲线Cyclic damage 周期性损坏Cyclic load 周期性负荷Cyclical deviation 周期(循环)离差Cyclical fluctuation 周期波动Cyclical trend 周期趋势Cyclical movement 周期移动Cyclical variation 周期变异Cycling failure rate 周期性失效率,周期性故障率DD chart d管制图Data 数据Data analysis 数据分析Data bank 资料室(库)Data exchange program 数据交换打算Data, inspection 检验数据Data item 数据项,文件项目Data processing 数据处理Death rate 死亡率Debug (debugging) 除错Decile 十分位数Decimal fraction 小数Decision function 决策函数Decision line 决定线Decision making 决策Decision variable 决策变数Decreasing failure rate distribution 递减失效率分配(布)Decrement 减量Decrement rate 减率Defect 疵病,缺点Defect, chronic 慢性缺点Defect, critical 严峻缺点Defect, incidental 偶发缺点Defect, major 要紧缺点Defect, minor 次要缺点Defect, sporadic 突发缺点Defect and failure analysis 缺点与失效分析Defect chart 缺点数(管制)图Defect Free 零缺点Defect prevention 缺点预防Defects, number of 缺点数Defects classification 缺点分类Defects per hundred units (dphu) 百件缺点数Defects per unit chart 每单位(内)缺点数(管制)图Defects per unit plan 每单位(内)缺点数(管制)打算Defective 不良品Defective, fraction 不良率Defective chart 不良品数(管制)图Defective material 不良材料Defective number 不良品数Defective part 不良零件Defective parts, percentage of 不良零件百分率Defective prevention 不良品预防Defective unit 不良品(单位)Defectives, number of 不良(品)数Defectives classification 不良品分类Definition(s) 定义Deflated series 调剂数列Deflated value 调剂值Deflating index 调剂指数Degradation 劣化Degradation failure 劣化故障,劣化失效Degree of accuracy 准确度Degree of approximation 近似度Degree of association 相联度Degree of confidence 信任(赖)度Degree of contribution 奉献度Degree of freedom (DF) 自由度Degree of reliability 可靠度Delivery 交货,出厂Delivery inspection 出厂检验Delivery qulaity 出厂品质Delivery time 运送时刻Demerit 减点Demerit chart 减点(数)(管制)图Demerit rating 减点评比Demerits per unit 每单位(内)减点数Demonstration 示范,验证,展现Demonstration test 验证试验,展现试验Density function 密度函数Dependability 可恃性,相依性,依靠性Dependent factor 因变因子Dependent failure 相依失效,相依故障Dependent variable 因变数Derating 降等,额降,减额定Derivation 导出Derived table 导出表Descriptive item 说明项Descriptive statistics 记述统计(学)Design 设计Design baseline 设计准则Design change 设计变更Design considerations 设计考虑Design control 设计管制Design change control 设计变更管制Design control, new 新设计管制Design criterion 设计准则Design disclosure package 设计启导文件Design effect cost 设计效应成本Design freeze 设计冻结Design in 设计到里面去Design input 设计输入Design matrix 设计矩阵Design output 设计输出Design of experiment 实验打算Design planning 设计规画Design profile 设计轮廓Design proving 设计认可Design qualification 设计之合格性Design release 设计公布Design requalification 设计合格之再认定Design review 设计审查Design specification 设计规格Design validation 设计确认Design verification 设计验证,查证Design verification test 设计验证试验Designation 名称Designed experiment 实验打算Destructive inspection (test) 破坏性检验(试验)Detailed design 细部设计Detailed design review 细部设计审查Detailed inspection (100% inspection) 全数检验(百分之百检验)Detect 侦测Detection of a failure unit 失效单位之检测,故障单位之检测Detection time 检测时刻Deterioration 衰变,劣化Determination, coefficient of 定限系数Development 进展Development test 进展试验Deviation 离差。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

品质名词(中英对照)AABC analysis ABC 分析Abnormality 不正常性Abscissa 横坐标Absolute deviation 绝对离差Absolute dispersion 绝对离势Absolute error 绝对误差Absolute frequency 绝对次数Absolute number 绝对数Absolute reliability 绝对可靠度Absolute term 绝对项Absolute value 绝对值Absolute variation 绝对变异Abstract number 抽象数Abstract unit 抽象单位Accelerated factor 加速系数,加速因子Accelerated life test 加速寿命试验Accelerated test 加速试验Acceleration 加速度Acceptable limit 允收界限Acceptable process 允收制程水平Acceptable quality 允收品质Acceptable quality level (AQL) 允收质量水平Acceptable reliability level (ARL) 允收可靠度水平Acceptability 允收性Acceptability criterion 允收标准Acceptance 允收,验收Acceptance, probability of 允收机率Acceptance, region of 允收区域Acceptance and rejection criteria 允收与拒收准则Acceptance boundary 允收界限Acceptance coefficient 允收系数Acceptance control chart 验收管制图Acceptance cost 验收费用Acceptance criteria 允收准则Acceptance error 允收误差Acceptance inspection 验收检验Acceptance limit 允收界限Acceptance line 允收线Acceptance number 允收(不良品)数Acceptance plan 验收计划Acceptance procedure 验收程序Acceptance/rectification scheme 允收/精选方案Acceptance sampling, attribute 计数值验收抽样Acceptance sampling, variable 计量值验收抽样Acceptance sampling plan 验收抽样计划Acceptance sampling scheme 验收抽样方案Acceptance test 验收试验Acceptance value 允收值Acceptance zone 允收区域Acceptance product 允收品Accepting lot 允收批Access time 接近时间,故障诊断时间Accessibility 可接近性Accident rate 意外率Accidental error 偶误,偶然误差Accidental fluctuation 偶然波动Accidental movement 意外移动Accounting test 验算(决算)试验Accumulated operating time 累积操作时间Accuracy 准确度Accuracy of data 数据准确度Accuracy of estimation 估计准确度Accuracy of the mean 平均数准确度Achieved availability 实际可用度Action 行动,措施Action, corrective 矫正行动(措施)Action control chart 行动管制图Action limit 行动界限Active line 行动线Active maintenance time 实际维护时间Active parallel redundancy 主动并复联(置)Active preventive maintenance 现行预防维护时间Active redundancy 主动复联(置)Active repair time 实际修复时间Active standby 主动备用Active time 运用时间Actual frequency 实际次数Actual limit 实际界限Actual range 实际全距Actual value 实际值Adaptability 可适应性Adaptive control 修改管制Addition theorem 加法定理Additivity 加法性,可加性Adjusted average 修正平均数Adjusted value 修正值Adjustment factor 调整系数Administration time for a repair 修复之管理时间Administrative time 管理时间Adopted value 采用值Advisory Group on Reliability of Electronic Equipment (AGREE) 电子装备可靠度顾问团Aeronautical Radio, Incorporated (ARINC) 航空无线电公司After-sales service 售后服务Age 年限Age at death 死亡年限Age at failure 失效年限Age-based maintenance 年限基准维护Aggregative method 综合法Aging 老化Agreement of quality assurance 质量保证之协议Agreement on verification method 验(查)证方法之协议Alarm signals 警告(报)讯号Alert time 待命时间Algebraic sum 代数和Algorism (Algorithm) 阿拉伯数字计数法Alias 假名Alienation 余相关Alignment chart 列线图Allocation 配当Allocation of reliability 可靠度配当Allowable percent defective (Acceptable quality level, AQL) 允收不良率(允收质量水平)Allowance 允差,裕度Alternative hypothesis 对立假设American Management Association (AMA) 美国管理协会American National Standards Institute (ANSI) 美国标准协会American Society for Quality Control (ASQC) 美国质量管理学会American Society for Mechanical Engineers (ASME) 美国机械工程师学会American Society for Testing and Materials (ASTM) 美国材料试验学会American Standard Association (ASA) 美国标准协会American Statistical Association (ASA) 美国统计协会American War Standards (AWS) 美国战时标准Ambient condition 周遭条件Analysis, sequential 逐次分析Analysis by accumulated frequency 累积法,累积次数分析Analysis by non-accumulated frequency 次数法,非累积次数分析Analysis of correlation 相关分析Analysis of covariance 共变异数分析Analysis of means (AVON) 平均数分析Analysis of problem 问题之分析Analysis of variance (ANOVA) 变异数分析Analysis sample 分析样本Analytical error 分析误差Angular transformation 角度转(变)换Anti-logarithm 逆对数Anti-mode 逆众数AOQL Sampling Table 平均出厂质量界限抽样数Applicability 应用性Applied statistics 应用统计学Apportionment of reliability 可靠度配当Apportionment techniques 配当技术Appraisal cost 鉴定成本,评估成本Appraisal system 评估制度Appraisal of quality 质量评估Approach to sequential testing 逐次试验法Approval of processes and equipment 核准制程与设备Approximate mode 近似众数Approximate number 近似数值Approximation 近似法,概算AQL (Acceptable quality level) 允收(质量)水平Arbitrary average (Assumed average, Arbitrary mean) 假定平均数Arbitrary origin 假定原点Arbitrary scale 假定标度Area bar chart 面积条图Area chart (diagram, graph) 面积图Area sampling 地区抽样Arithmetic average 算术平均数Arithmetic cross 算术交叉Arithmetic graph 算术图Arithmetic line chart 算术线图Arithmetic mean 算术平均数Arithmetic paper 算术纸Arithmetic probability paper 算术机率纸Arithmetic progression (Arithmetic series) 算术级数,等差级数Arithmetic scale 算术标度,等差标度Arithmetic series 算术级数,等差级数Army Ordnance Table 陆军兵工署(抽样)表Army Service Forces Table 陆军(抽样)表序列Array 序列Array distribution 序列分配(布)Array of data 数据序列Assemble 装配(组立)Assembled product 装配品Assembly 装配件Assembly inspection 装配检验Assembly quality analysis report 装配质量分析报告Assessed failure rate 评估失效率Assessed mean active -maintenance time 评估时间现行维护时间Assessed mean life 评估平均寿命Assessed mean time between failures 评估平均失效间格时间Assessed mean time to failure 评估平均失效前时间Assessed reliability 评估可靠度Assessed value 评估值Assessment of subcontractor 分包商之评鉴Assignable cause (Special cause) 非机遇原因(特殊原因)Assignable variation 非机遇变异Associated dependent variable 相联因变数Associated variate 相联变量Association coefficient 相联系数Association of attribute 品性相联Association table 相联表,联合表Assumed mean (Assumed average, Arbitrary average) 假定平均数Assumed median 假定中位数Assumed origin 假定原点Assurance quality 保证质量Assurance function 保证功能Asymmetrical distribution 不对称分配(布)Asymmetry 不对称Asymptotic distribution 趋近分配(布)At random 随机Attribute 计数值,属性Attribute classification 品性分类Attribute data 计数数据Attribute inspection 计数值检验Attribute sampling 计数值抽样Attribute sampling plan 计数值抽样计划Attribute testing (Go no-go testing) 计数值试验(通过与不通过试验)Attribute value 计数值Audit 稽核Audit for reliability 可靠度稽核Audit of decision 稽核决策Audit plan 稽核计划Audit report 稽核报告Auditing report 稽核报告Auto-correlation 自动相关Automatic switch-over redundancy 自动切换复联(置)Automatic test equipment (Am) 自动试验装备Auto-regression 自动回归Availability 可用性,可用度Average (Mean) 平均数,平均值Average, grand 总平均Average, moving 移动平均数Average, sample 样本平均数Average, standard error of 标准误平均数Average, universe 群体平均数Average, weighted 加权平均数Average amount of inspection 平均检验数Average and range chart 平均数及全距(管制)图Average availability 平均可用度Average deviation (A.D.) (Mean deviation) 平均差Average error (Mean error) 平均误差Average number of defects 平均缺点数Average of ratios 比例平均数Average outgoing quality (AOQ) 平均出厂质量Average outgoing quality curve 平均出厂质量曲线Average outgoing quality level 平均出厂质量水平Average outgoing quality limit (AOQL) 平均出厂水平Average quality level 平均出厂质量界限Average quality level line 质量平均线Average quality protection 平均质量保护Average range 平均全距Average run length (ARL) 平均连串长度Average sample number (ASN) 平均样品数Average range 平均全距Average run length (ARL) 平均连串长度Average sample number(ASN) 平均样本数Average sample number curve 平均样本曲线Average sample size (ASS) 平均样本大小Average sample size curve 平均样本大小曲线Average sample 平均抽样Average total inspection (ATI) 平均总检验(件)数Average total inspection curve 平均总检验数曲线Average value 平均值Avoidable cause 可避免之原因Avoidable quality cost 可避免之质量成本Axiom 公理Axis 轴Axis of abscissa 横轴Axis of ordinate 纵轴BBad lot 坏批Balance frequency 平衡次数Balanced complete type 平衡完备型Balanced design 平衡设计Balanced experiment 平衡实验Balanced incomplete type 平衡不完备型Balanced sample 平衡样本Band chart 带形图Band curve chart 带形曲线图Bank of reliability data 可靠度数据库Bar chart (diagram) 条(形)图Bartlett's test 巴特莱特试验Base line 基线Base number 基数Base period 基期Base point 基点Basic reliability 基本可靠度Batch (Lot) 批Batch of material 材料批Batch process 分批制造方法Batch size 批量Batch testing 批试验Bathtub curve 浴缸曲线Bathtub failure curve 浴缸失效曲线Bayes' estimator 贝式估计式Bayes' theorem 贝式定理Bayesian approach 贝式法Bayesian approcah to design 贝式设计法Bayesian estimation 贝式估计Bead map 标珠图Bell-shaped curve 钟形曲线Bell-shaped distribution 钟形分配(布)Bell-shaped failure pattern 钟形失效型态JBell System 贝尔系统Bell Telephone Laboratories 贝尔电话实验室Bell Telephone Laboratories Sampling Table 贝尔(电话实验室)抽样表Benign failure 无危险的失效Bernoulli distribution 白努利分配(布)Best fit 最适配合Best fitting line 最适线Best fitting curve 最适曲线Best linear invariant estimator 最佳线型不变估计式Best linear unbiased estimator 最佳线型不偏估计式Beta coefficient β系数Beta distribution β分配(布)Beta function β函数Between-class variance 组间变异数Between-column variance 组间变异Between-column variation 行间变异Between-row variation 列间变异Between sample variation 样本间变异Bias 偏差Bias, downward 向下偏差Bias, downward type 向下型偏差Bias, upward 向上偏差Bias, upward type 向上型偏差Biased error 偏误Biased estimate 偏差估计Biased sample 偏差样本Biased test 偏差试验Bilateral 双边Bill of material (BOM) 物料清单Bimodal 双峰Bimodal curve 双峰曲线Bimodal distribution 双峰分配(布)Bimodal redundancy 双峰型复联(置)Bimodality 双峰性Binary system 二元制Binomial, skewed 偏态二项Binomial coefficient 二项系数Binomial curve 二项曲线Binomial distribution 二项分配(布)Binomial equation 二项方程式Binomial expansion 二项展开式Binomial population 二项群体Binomial probability distribution 二项机率分配(布)Binomial probability paper(BIPP) 二项机率纸Binomial series 二项级数Binomial theorem 二项定理Bi-serial 双数列Biserial correlation 双数列相关Biserial coefficient of correlation 双数列相关系数Biserial ratio of correlation 双数列相关比Bivariate 双变量Bivariate distribution 双变量分配(布)Bivariate frequency distribution 双变量次数分配(布)Bivariate normal distribution 双变量常态分配(布)Blend 混,混合Block 量块,(实验)区,方块Block design 实验区设计Block diagram 方块图Block factor 地区因素Block in series 串联方块Boundary 界Boundary, cell 组界Bowker-Goode variables plan Bowker-Goode 记量值(抽样)计划Bowl drawing 碗珠抽样Bowl experiment 碗珠实验Bowl test 碗珠试验Bowley's coefficient of skewness Bowley偏态系数Bowley's formula Bowley公式Bureau of Ordnance, U.S. Navy 美国海军兵工署Break-even chart 损益平衡图Break-even point (BEP) 损益平衡点Breakthrough 突破British Standards Institution 英国标准协会Broken curve 中断曲线Broken series 中断数列Broken trend 中断趋势Built-in test (BIT) 内含测试,自测Bureau of Commodity Inspection and Quarantine (BCIQ) 商品检验局Bulk sampling Burn-in 大宗抽样Business Process Management (BPM) 业务流程管理Buyer 买方,客户CC chart C(管制)图Calculated value (Computed value) 计算值Calculation chart 计算图Calendar time 日历时间Calibration 校正Calibration record 校正记录Camp-Meidell inequality Camp-Meidell不等式Capability 能力Capability, machine 机器能力Capability, process 制程能力Capability ratio 能力比Capacity 能量,容量Caption 纵标目Carrying out the audit 实施稽核Cartogram 统计图Case method 个案法Catastrophic failure 突然故障,崩坏失效,致命失效Category 类别Cauchy distribution Cauchy 分配(布)Causality 因果律Cause 原因Cause, assignable 非机遇原因Cause, avoidable 可避免原因Cause, chance 机遇原因Cause, common 共同原因Cause, findable 可寻找原因Cause, random 随机原因Cause, special 特殊原因Cause, substantial 本质原因Cause, unavoidable 不可避免原因Cause and effect 因果Cause and effect diagram 特性要因图Cell 组Cell boundary 组界Cell deviation (d) 组离差Cell frequency (f) 组次数Cell interval (i,h) 组距Cell limit 组限Cell method 分组法Cell mid-point (Xm) 组中点Cell value 组值Censored sample 检剔样本Censored test 检剔试验Censorship 检剔Census 普查Center line 中线Central inspection station 中央检验站Central limit theory 趋中理论,中央极限理论Central limit theorem 趋中理论,中央极限理论Central line (CL.) 中心线Central moment 中心动差Central ordinate 中纵坐标Central tendency 集中趋势Central value 中值,中心值Certainty 确定性Certified chart 验证图Certified equipment 合格设备Certified quality engineer (CQE) 合格质量工程师Certified quality technician (CQT) 合格质量技术师Certified reliability engineer (CRE) 合格可靠度工程师Certification 验证Chain model 炼结模型Chain reliability 炼结可靠度Chain sampling plan (CHSP) 炼结抽样计划Chance 机遇Chance cause 机遇原因Chance error (Probable error) 机遇误差,机误Chance factor 机遇因素Chance failure 机遇故障,机遇失效Chance failure period 机遇失效期Chance fluctuation 机遇波动Chance variable 机遇变数Chance variation 机遇变异Change control 改变(变更)管理Chaotic variation 混乱变异Characteristic (质量)特性Characteristic, qualitative 质的特性Characteristic, quantitative 量的特性Characteristic curve, operating (OC curve) 操作特性曲线, OC曲线Characteristic diagram 特性要因图Characteristic function 特性函数Characteristic life 特性寿命Characteristic operating curve (OC curve) 特性操作曲线(OC曲线)Characteristic value 特性值Chargeable failure 可计列失效,故障Charlier check Charlier 覆检法Chart 图,(管制)图Chart, acceptance control 验收管制图Chart, average and range 平均数及全距(管制)图Chart, average number of defects 平均缺点数(管制)图Chart, control 管制图Chart, cumulative sum 累积和(管制)图Chart, defects per unit 每单位内缺点数(管制)图Chart, fraction defective 不良率(管制)图Chart, group 多项(管制)图Chart, individual 个别值(管制)图Chart, median 中位数(管制)图Chart, moving and range 移动平均数及全距(管制)图Chart, moving range 移动全距(管制)图Chart, modified control limits 修正管制界限(管制)图Chart, multi-variation 变异值(管制)图Chart, multiple 复式(管制)图Chart, number defectives 不良(品)数(管制)图Chart, number of defects 缺点数(管制)图Chart, percent defective 不良率管制图Chart, range 全距(管制)图Chart, run 操作(记录)图Chart, shop 工厂(管制)图Chart, Shewhart control Shewhart 管制图Chart, two-way control 双向管制图Chebyshev's inequality Chebyshev 不等式Check inspection 复核检验Check sampling 复核检验员Check inspector 复核抽样Chi-square ,卡方Chi-square distribution 分配(布),卡方分配(布)Chi-square test 检定,卡方检定Chi-squared distribution 分配(布),卡方分配(布)Chip 小圆片Chronic defect 慢性缺点Chronological chart 时序图Chronological series 时序数列Class 组Class boundaries (True class limits)组界(真实组限)Class form 组形Class frequency (f) 组次数Class interval (i,h) 组距Class limit 组限Class mark 组标,中值Class mean 组平均数Class mid-point(Xm) 组中点Class mid-value 组中值Class of median 组中位数Class value 组值Classes, number of 组数Classification chart 分组,分类Classification frequency 分组次数Classification frequency series 分组次数数列Classification of defectives 不良品分类Classification of defects 缺点分类Classfication of failure 失效分类,故障分类Classification process 分组(方)法Clearance 间隙,余隙Cluster 集团Cluster sampling 集团抽样Cochran's test Cochran 检定Code 简化,代号Code letter 代字Coded unit 简化单位Coded value 简化值Coding 简化Coding rule 简化规则Coefficient 系数Coefficient, correlation 相关系数Coefficient of alienation 余相关系数Coefficient of association 相关系数Coefficient of binomial distribution 二项分配(布)系数Coefficient of colligation 束联系数Coefficient of contingency 列联系数Coefficient of correlation 相关系数Coefficient of determination (r2) 定限系数Coefficient of dispersion 离势系数Coefficient of kurtosis 峰度系数Coefficient of multiple correlation 复相关系数Coefficient of net correlation 净相关系数Coefficient of net regression 净回归系数Coefficient of non-determination 不定限系数Coefficient of part correlation 部份相关系数Coefficient of partial correlation 部份相关系数Coefficient of rank correlation 等级相关系数Coefficient of reliability 可靠度系数Coefficient of regression 回归系数Coefficient of skewness 偏态系数,偏斜系数Coefficient of variation (CV) 变异系数Cold standby 冷置系数Collective quality 集体品质Columbia sampling table Columbia 抽样计划Column (Column/Row) 行,纵行(行/列)Column head 标目Column diagram 直行图Combination 组合Combinational model 复合模型Combined environmental reliability test (CERT) 复合环境可靠度试验Combined failure 复合失效,复合故障Combined stress life test 复合应力寿命试验Commissioning 委制Commodity 商品Common cause (Chance cause) 共同原因(机遇原因)Company standard 公司标准Companys need 公司需要Company-wide quality control (CWQC) 全公司质量管理Comparability 可比性Comparable measure 可比量数Compensating error 补偿误差Compensating fluctuation 补偿波动Competing product 竞争产品Complete association 全相联Complete block design 完全区集法Complete confounding 完全交络Complete dissociation 全不相联Complete failure 完全故障,完全失效Completely randomized design 完全随机法Complaint 抱怨Complaint index 抱怨指标Completed product verification 成品验证Component 组件,组件Component bar chart 成份条图Component distiibution 组成份分配(布)Component part diagram 成份图Component ratio 成份比Component reliability 组件可靠度Component variance 成份变异数Components of variance 变异数成份Composite curve 复合曲线Composite design 复合法Composite hypothesis 复合假设,组合假设Composite unit 复合单位Compound distribution 复合分配(布)Compound event 复合事件Compound probability 复合机率Compounding technique 复合法Compressed limit 压缩界限Compressed limit gauging 压缩界限规则Computed value 计算值Concentric circle diagram 同心圆图Conception of limit 极限概念Conceptual design 概念设计Conceptual design review 概念设计审查Concession 特采,特认Concomitant factor 共变因素Concomitant variable 共变数Concomitant variation 共变异Concurrency 并行Condition maintenance 状态维护Condition monitoring 状态监督Condition-based maintenance 状态基准维护Conditional probability 条件机率Conditions of use 使用条件Confidence 信任,信赖Confidence coefficient 信任系数,信赖系数Confidence interval 信任区间,信赖区间Confidence in test results 试验结果的信赖度Confidence level 信任水平,信赖水平Confidence limit 信任界限,信赖界限Confidence range 信任全距,信赖全距Configuration control 型态管制Configuration items 型态件Configuration management 型态管理Confirmation 确认Conformance to the requirement 符合要求Conformation 一致Conforming article 合格品Conformity 符合Confounding 交络Confounding, complete 完全交络Confounding, partial 部份交络Connector 连接器Consignment 委托,寄售Consistency 一致性Constancy 恒久性Constancy of great numbers 大数恒久性Constant 常数Constant cause system 恒常原因系统Constant error 恒常误差Constant failure period 恒常失效期Constant failure rate dustribution 恒常失效率分配(布)Constant weight (Fixed weight) 固定权数Constraint 束缚Consultant 管理顾问师Consumer 消费者Consumer acceptance specification 消费者允收规格Consumerism 消费者主义Consumer's risk (CR) 消费者冒险率Consumer test panel 消费者试验小组Consumer preference 消费者偏好Consumer sensitivity test 消费者感官试验Contingency 列联Contingency coefficient 列联系数Contingency table 列联表Contingency theorem 列联理论Continuity correction 连续校正Continuous change 连续变更Continuous data 连续数据Continuous distribution 连续分配(布)Continuous production 连续生产Continuous sampling 连续抽样Continuous sampling plan (CSP) 连续抽样计划Continuous series 连续数列Continuous variable 连续变量Contract 合约Contract preparation 拟定合约Contract review 合约检讨Contract requirements 合约需求Contract requirements analysis 合约需求分析Contractors 合约商Contrast analysis 对照分析Control, in 在管制(状态)下Control, lack of 缺乏管制Control, out of 超出管制Control, state of 管制状态Control, under 在管制(状态)下Control chart 管制图Control chart, cumulative sum 累积和管制图Control chart, defects per unit 每单位内缺点数管制图Control chart, two-way 双向管制图Control chart factor 管制图系数Control chart for attribute 计数值管制图Control chart for variable (measurement) 计量值管制图Control chart method 管制图法Control chart pattern 管制图类型Control factor 管制因素Control gaging (gauging) 管制规测Control level 管制水平Control limit 管制界限Control limit, lower 管制下限Control limit, modified 修正管制界限Control limit, upper 管制上限Control limit factor 管制界限因子Control line 管制线Control of measuring and test equipment 量测与试验设备之管制Control of nonconforming material 不合格物料之管制Control of nonconforming product 不合格产品之管制Control of production 生产管制Control of reliability 可靠度管制Control of verification status 验证状况之管制Control plan 管制计划Control point 管制点Control station 管制站Control system 管制系统Controllability 可管制性Controlled process 管制制程Controlled state 管制状态Controlled variability 管制变异性Controlled variable 管制变数Controlling item 管制项目Convenience lot 合宜的批Convergence 收敛Cooked distribution 中断分配(布)Coordinate 坐标Coordinate axis 坐标轴Coordinate line 坐标线Coordination 协调Coordination for reliability 可靠度协调Correction 校正,修正Correction, Sheppard Sheppard 校正数Correction factor 修正因子Correction for continuity 连续校正Correction for mean 平均数校正Correction term 校正项Corrective action 矫正行动,改正措施Corrective maintenance 矫正维护,改正维护Corrective maintenance time 矫正维护时间,改正维护时间Corrective sorting 修正选别Correlated measure 相关量数Correlated samples 相关样本Correlation 相关Correlation, coefficient of 相关系数Correlation, direct 直接相关Correlation, index of 相关指数Correlation, inverse 反相关Correlation, multiple 复相关Correlation, negative 负相关Correlation, net 净相关Correlation, nonlinear 非线性相关Correlation, nonsense 无意义相关Correlation, part 部份相关,偏相关Correlation, partial 部份相关,偏相关Correlation, perfect 完全相关Correlation, rank 等级相关Correlation, serial 数序相关Correlation, simple 简相关Correlation, zero 零相关Correlation analysis 相关分析Correlation chart 相关图Correlation, coefficient 相关系数Correlation coefficient, rank 等级相关系数Correlation matrix 相关矩阵Correlation of attributes 品性相关Correlation ratio 相关比Correlation of x on y x与y的相关比Correlation ratio of y on x y与x的相关比Correlation scatter chart 相关散布图Correlation surface 相关面Correlation table 相关表Correlation theory 相关理论Correlogram 相关图Corrosive atmosphere 腐蚀性空气Cost 成本,费用Cost, acquisition 取得成本Cost, appraisal 评估(鉴定)成本Cost, external failure 外部失败成本Cost, internal failure 内部失败成本Cost, life cycle 寿命周期成本Cost, logistic 后续成本Cost, prevention 预防成本Cost, quality 质量成本Cost, quality control 质量管理成本Cost, rework 重加工成本Cost effectiveness 成本效益Cost function 成本机能Cost model for reliability optimization 可靠度最佳化成本模式Cost reduction 成本减低Count (Countable) data 点计数据Counter variation 反行变异Co-variation 共变异Covariance 共变异数,共变数Covariance analysis 共变异数分析Covariance matrix 共变异矩阵Craps, game of 掷骰游戏Credibility 信用Creep failure 潜变失效,潜变故障Crest 峰Criteria for workmanship 工作技艺准则Criterion 准则,规范Criterion, acceptance 验收准则(规范)Critical component control 重要组件管制Critical defect 严重缺点Critical defective 严重不良品Critical design review 关键设计审查Critical failure 关键故障,严重失效Critical items 关键品目,重要件Critical path 要径Critical path analysis 要径分析法Critical region 临界区域,弃却区域,判定区Critical value 临界值,判定值Criticality 严重性,关键性Cross 交叉Cross check 互校Cross classification 交叉分类Cross correlation 交叉相关Cross formula 交互公式Cross-hatch 交叉线Cross-hatched map 交叉图Cross-over design 交叉计划Crossed design 交叉法Crude mode 概括众数Crude moment 概括动差Cubic chart (diagram) 立方图Culled 检选Cumulant 累积数Cumulation, downward 向下累积Cumulation, total 全部累积Cumulation, upward 向上累积Cumulation average chart 累积平均数(管制)图Cumulative curve 累积曲线Cumulative curve chart 累积曲线图Cumulative damage 累积损坏Cumulative distribution (Ogive) 累积分配(布)Cumulative distribution function 累积分配(布)函数Cumulative error 累积误差Cumulative failure frequency 累积故障次数,累积失效次数Cumulative frequency 累积次数Cumulative frequency arrangement 累积次数排列Cumulative frequency curve 累积次数曲线Cumulative frequency 累积次数曲线图Cumulative frequency distribution 累积次数分配(布)Cumulative frequency polygon 累积(次数)多边形Cumulative frequency (probability) function 累积次数(机率)函数Cumulative frequency table 累积次数表Cumulative function 累积函数Cumulative graph 累积图Cumulative hazard function 累积冒险函数Cumulative mean 累积平均数Cumulative normal distribution 累积常态分配Cumulative number of failures 累积失效数,累积故障数Cumulative percentage of failures 累积失效百分率,累积故障百分率Cumulative probability distribution 累积机率分配(布)Cumulative sum 累积和Cumulative sum chart 累积和(管制)图Cumulative sum control chart 累积和管制图Cumulative terms 累积项Curtailed (Truncated) inspection 截略检验Curtailed (Truncated) sample inspection截略样品检验Curtailed sampling 截略抽样Curtailed sampling inspection 截略抽样检验Curtaijed sampling plan 截略抽样计划Curtailment of sampling plan 抽样计划之截略Curve 曲线Curve, frequency 次数曲线Curve, normal 常态曲线Curve chart (diagram) 曲线图Curve fitting 曲线配合Curve of error 误差曲线Curve of means 平均数曲线Curve of probability 机率曲线Curve type criterion 曲线型准则Curve shape 曲线形状Curvilinear correlation 曲线相关Curvilinear regression 曲线回归Curvilinear trend 曲线趋势Curvilinearity 曲线性Customer 客户,顾客Customer complaint 顾客抱怨Customer feedback information 顾客回馈信息Customer incurred cost 顾客引发成本Customer operation cost 顾客作业成本Customer repair cost 顾客修理成本Customer requirement 顾客要求Customer satisfaction 顾客满意度Customer's need 顾客需要Cusum chart 累积和(管制)图Cycles 周期Cycles between failures 失效间隔周期,故障间隔周期Cycle of operation 操作周期Cyclic curve 周期(循环)曲线Cyclic damage 周期性损坏Cyclic load 周期性负荷Cyclical deviation 周期(循环)离差Cyclical fluctuation 周期波动Cyclical trend 周期趋势Cyclical movement 周期移动Cyclical variation 周期变异Cycling failure rate 周期性失效率,周期性故障率DD chart d管制图Data 数据Data analysis 数据分析Data bank 资料室(库)Data exchange program 数据交换计划Data, inspection 检验数据Data item 数据项,文件项目Data processing 数据处理Death rate 死亡率Debug (debugging) 除错Decile 十分位数Decimal fraction 小数Decision function 决策函数Decision line 决定线Decision making 决策Decision variable 决策变数Decreasing failure rate distribution 递减失效率分配(布)Decrement 减量Decrement rate 减率Defect 疵病,缺点Defect, chronic 慢性缺点Defect, critical 严重缺点Defect, incidental 偶发缺点Defect, major 主要缺点Defect, minor 次要缺点Defect, sporadic 突发缺点Defect and failure analysis 缺点与失效分析Defect chart 缺点数(管制)图Defect Free 零缺点Defect prevention 缺点预防Defects, number of 缺点数Defects classification 缺点分类Defects per hundred units (dphu) 百件缺点数Defects per unit chart 每单位(内)缺点数(管制)图Defects per unit plan 每单位(内)缺点数(管制)计划Defective 不良品Defective, fraction 不良率Defective chart 不良品数(管制)图Defective material 不良材料Defective number 不良品数Defective part 不良零件Defective parts, percentage of 不良零件百分率Defective prevention 不良品预防Defective unit 不良品(单位)Defectives, number of 不良(品)数Defectives classification 不良品分类Definition(s) 定义Deflated series 调节数列Deflated value 调节值Deflating index 调节指数Degradation 劣化Degradation failure 劣化故障,劣化失效Degree of accuracy 准确度Degree of approximation 近似度Degree of association 相联度Degree of confidence 信任(赖)度Degree of contribution 贡献度Degree of freedom (DF) 自由度Degree of reliability 可靠度Delivery 交货,出厂Delivery inspection 出厂检验Delivery qulaity 出厂品质Delivery time 运送时间Demerit 减点Demerit chart 减点(数)(管制)图Demerit rating 减点评比Demerits per unit 每单位(内)减点数Demonstration 示范,验证,展现Demonstration test 验证试验,展现试验Density function 密度函数Dependability 可恃性,相依性,依赖性Dependent factor 因变因子Dependent failure 相依失效,相依故障Dependent variable 因变数Derating 降等,额降,减额定Derivation 导出Derived table 导出表Descriptive item 说明项Descriptive statistics 记述统计(学)Design 设计Design baseline 设计准则Design change 设计变更Design considerations 设计考虑Design control 设计管制Design change control 设计变更管制Design control, new 新设计管制Design criterion 设计准则Design disclosure package 设计启导文件Design effect cost 设计效应成本Design freeze 设计冻结Design in 设计进去Design input 设计输入Design matrix 设计矩阵Design output 设计输出Design of experiment 实验计划Design planning 设计规画Design profile 设计轮廓Design proving 设计认可Design qualification 设计之合格性Design release 设计发布Design requalification 设计合格之再认定Design review 设计审查Design specification 设计规格Design validation 设计确认Design verification 设计验证,查证Design verification test 设计验证试验Designation 名称Designed experiment 实验计划Destructive inspection (test) 破坏性检验(试验)Detailed design 细部设计Detailed design review 细部设计审查Detailed inspection (100% inspection) 全数检验(百分之百检验)Detect 侦测Detection of a failure unit 失效单位之检测,故障单位之检测Detection time 检测时间Deterioration 衰变,劣化Determination, coefficient of 定限系数Development 发展Development test 发展试验Deviation 离差Deviation, average 平均差Deviation, mean 平均差Deviation, root-mean-square 均方根差Deviation, sample standard 样本标准差Deviation, standard 标准差Deviation, universe standard 群体标准差Deviation permit 差异特许Deviation report 差异报告Diagnosis 诊断Diagnostic arm 诊断能力Diagonal distribution 对角分配(布)Diagram, bar 条(形)图Diagram, curve 曲线图Diagram, scatter 散布图Diagrammatic presentation (Graphic presentation) 图示Dice experiment 掷骰实验Dichotomy 二分法Dichotomy, double 双次二分法Dictogram 实体图Difference, significance of 差异之显著性Difference control chart 差异管制图Difference correlation 差异相关Difference method, t-test 差异之t检定。

相关文档
最新文档