机械电气专业英文词汇
机电行业英语
机电行业英语机电行业英语是指与机械和电气相关的行业所使用的英语词汇和表达。
以下是一些常见的机电行业英语词汇和短语：1. Mechanical engineering - 机械工程2. Electrical engineering - 电气工程3. Automation - 自动化4. Control system - 控制系统5. Electric motor - 电动机6. Generator - 发电机7. Transformer - 变压器8. Circuit - 电路9. Voltage - 电压10. Current - 电流11. Resistance - 电阻12. Power supply - 电源13. Fault diagnosis - 故障诊断14. Maintenance - 维护15. Troubleshooting - 故障排除16. Installation - 安装17. Wiring - 线路连接18. Assembly - 组装19. Calibration - 校准20. Safety precautions - 安全注意事项此外，还有许多与具体行业相关的词汇和表达，例如：1. Mechanical design - 机械设计2. Industrial automation - 工业自动化3. Power generation - 发电4. Robotics - 机器人技术5. HVAC (heating, ventilation, and air conditioning) - 暖通空调在机电行业工作，掌握这些词汇和表达，可以更好地与国际合作伙伴交流并理解技术文档或工程要求。
电气、机械等专业英语词汇大全(总结)(最新整理)
自动化专业词汇induction machine 感应式电机 horseshoe magnet 马蹄形磁铁 magnetic field 磁场 eddy current 涡流 right-hand rule 右手定则 left-hand rule 左手定则 slip 转差率 induction motor 感应电动机 rotating magnetic field 旋转磁场 winding 绕组 stator 定子 rotor 转子 induced current 感生电流 time-phase 时间相位 exciting voltage 励磁电压 solt 槽 lamination 叠片 laminated core 叠片铁芯 short-circuiting ring 短路环 squirrel cage 鼠笼 rotor core 转子铁芯 cast-aluminum rotor 铸铝转子 bronze 青铜 horsepower 马力 random-wound 散绕 insulation 绝缘 ac motor 交流环电动机 end ring 端环 alloy 合金 coil winding 线圈绕组 form-wound 模绕 performance characteristic 工作特性 frequency 频率 revolutions per minute 转/分 motoring 电动机驱动 generating 发电 per-unit value 标么值 breakdown torque 极限转矩 breakaway force 起步阻力 overhauling 检修 wind-driven generator 风动发电机 revolutions per second 转/秒 number of poles 极数 speed-torque curve 转速力矩特性曲线 plugging 反向制动 synchronous speed 同步转速 percentage 百分数 locked-rotor torque 锁定转子转矩 full-load torque 满载转矩 prime mover 原动机 inrush current 涌流 magnetizing reacance 磁化电抗 line-to-neutral 线与中性点间的 staor winding 定子绕组 leakage reactance 漏磁电抗 no-load 空载 full load 满载 Polyphase 多相(的) iron-loss 铁损 complex impedance 复数阻抗 rotor resistance 转子电阻 leakage flux 漏磁通 locked-rotor 锁定转子 chopper circuit 斩波电路 separately excited 他励的 compounded 复励 dc motor 直流电动机 de machine 直流电机 speed regulation 速度调节 shunt 并励 series 串励 armature circuit 电枢电路 optical fiber 光纤 interoffice 局间的 waveguide 波导波导管 bandwidth 带宽 light emitting diode 发光二极管 silica 硅石二氧化硅 regeneration 再生, 后反馈放大 coaxial 共轴的,同轴的 high-performance 高性能的 carrier 载波 mature 成熟的 Single Side Band(SSB) 单边带 coupling capacitor 结合电容 propagate 传导传播 modulator 调制器 demodulator 解调器 line trap 限波器 shunt 分路器 Amplitude Modulation(AM)调幅 Frequency Shift Keying(FSK)移频键控 tuner 调谐器 attenuate 衰减 incident 入射的 two-way configuration 二线制 generator voltage 发电机电压 dc generator 直流发电机 polyphase rectifier 多相整流器 boost 增压 time constant 时间常数 forward transfer function 正向传递函数 error signal 误差信号 regulator 调节器 stabilizing transformer 稳定变压器 time delay 延时 direct axis transient time constant 直轴瞬变时间常数 transient response 瞬态响应 solid state 固体 buck 补偿 operational calculus 算符演算 gain 增益 pole 极点 feedback signal 反馈信号 dynamic response 动态响应 voltage control system 电压控制系统 mismatch 失配 error detector 误差检测器 excitation system 励磁系统 field current 励磁电流 transistor 晶体管 high-gain 高增益 boost-buck 升压去磁 feedback system 反馈系统 reactive power 无功功率 feedback loop 反馈回路 automatic Voltage regulator(AVR)自动电压调整器 reference Voltage 基准电压 magnetic amplifier 磁放大器 amplidyne 微场扩流发电机 self-exciting 自励的 limiter 限幅器 manual control 手动控制 block diagram 方框图 linear zone 线性区 potential transformer 电压互感器 stabilization network 稳定网络 stabilizer 稳定器 air-gap flux 气隙磁通 saturation effect 饱和效应 saturation curve 饱和曲线 flux linkage 磁链 per unit value 标么值 shunt field 并励磁场 magnetic circuit 磁路 load-saturation curve 负载饱和曲线 air-gap line 气隙磁化线 polyphase rectifier 多相整流器 circuit components 电路元件 circuit parameters 电路参数 electrical device 电气设备 electric energy 电能 primary cell 原生电池 energy converter 电能转换器 conductor 导体 heating appliance 电热器 direct-current 直流 time invariant 时不变的 self-inductor 自感 mutual-inductor 互感 the dielectric 电介质 storage battery 蓄电池 e.m.f = electromotive fore 电动势 unidirectional current 单方向性电流 circuit diagram 电路图 load characteristic 负载特性 terminal voltage 端电压 external characteristic 外特性 conductance 电导 volt-ampere characteristics 伏安特性 carbon-filament lamp 碳丝灯泡 ideal source 理想电源 internal resistance 内阻 active (passive) circuit elements 有（无）源电路元件 leakage current 漏电流 circuit branch 支路 P.D. = potential drop 电压降 potential distribution 电位分布 r.m.s values = root mean square values 均方根值 effective values 有效值 steady direct current 恒稳直流电 sinusoidal time function 正弦时间函数 complex number 复数 Cartesian coordinates 笛卡儿坐标系 modulus 模 real part 实部 imaginary part 虚部 displacement current 位移电流 trigonometric transformations 瞬时值 epoch angle 初相角 phase displacement 相位差 signal amplifier 小信号放大器 mid-frequency band 中频带 bipolar junction transistor (BJT)双极性晶体管 field effect transistor (FET)场效应管 electrode 电极电焊条 polarity 极性 gain 增益 isolation 隔离分离绝缘隔振 emitter 发射管放射器发射极 collector 集电极 base 基极 self-bias resistor 自偏置电阻 triangular symbol 三角符号 phase reversal 反相 infinite voltage gain 无穷大电压增益 feedback component 反馈元件 differentiation 微分 integration 积分下限 impedance 阻抗 fidelity 保真度 summing circuit 总和线路反馈系统中的比较环节 Oscillation 振荡 inverse 倒数 admittance 导纳 transformer 变压器 turns ratio 变比匝比 ampere-turns 安匝(数) mutual flux 交互(主)磁通 vector equation 向(相)量方程 power frequency 工频 capacitance effect 电容效应 induction machine 感应电机 shunt excited 并励 series excited 串励 separately excited 他励 self excited 自励 field winding 磁场绕组励磁绕组 speed-torque characteristic 速度转矩特性 dynamic-state operation 动态运行 salient poles 凸极 excited by 励磁 field coils 励磁线圈 air-gap flux distribution 气隙磁通分布 direct axis 直轴 armature coil 电枢线圈 rotating commutator 旋转（整流子）换向器 commutator-brush combination 换向器-电刷总线 mechanical rectifier 机械式整流器 armature m.m.f. wave 电枢磁势波 Geometrical position 几何位置 magnetic torque 电磁转矩 spatial waveform 空间波形 sinusoidal – density wave 正弦磁密度 external armature circuit 电枢外电路 instantaneous electric power 瞬时电功率 instantaneous mechanical power 瞬时机械功率 effects of saturation 饱和效应 reluctance 磁阻 power amplifier 功率放大器 compound generator 复励发电机 rheostat 变阻器 self – excitation process 自励过程 commutation condition 换向状况 cumulatively compounded motor 积复励电动机 operating condition 运行状态 equivalent T – circuit T型等值电路 rotor (stator) winding 转子（定子绕组） winding loss 绕组（铜）损耗 prime motor 原动机 active component 有功分量 reactive component 无功分量 electromagnetic torque 电磁转矩 retarding torque 制动转矩 inductive component 感性（无功）分量 abscissa axis 横坐标 induction generator 感应发电机 synchronous generator 同步发电机 automatic station 无人值守电站 hydropower station 水电站 process of self – excitation 自励过程 auxiliary motor 辅助电动机 technical specifications 技术条件 voltage across the terminals 端电压 steady – state condition 瞬态暂态 reactive in respect to 相对….呈感性 active in respect to 相对….呈阻性 synchronous condenser 同步进相（调相）机 coincide in phase with 与….同相 synchronous reactance 同步电抗 algebraic 代数的 algorithmic 算法的 1--master element 主要元件，是指控制开关等元件。
(完整版)机械电子类专业英语概要
1机械专业英语词汇Date 约会金属切削metal cuttingServey 调查Liquid Crystal Display LCD机床machine tool金属工艺学technology of metals刀具cutter摩擦friction联结link传动drive/transmission轴shaft axis/'æksis]/弹性elasticity [,elæs'tisəti]频率特性frequency characteristic误差error响应response定位allocation机床夹具jig [dʒiɡ]动力学dynamic运动学kinematic [,kɪnɪ'mætɪk]静力学static分析力学analyse mechanics [mi'kæniks]拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor[ei'siŋkrənəs]几何形状geometrical精度precision [pri'siʒən]正弦形的sinusoid交流电路AC circuit ['sə:kit]机械加工余量machining allowance变形力deforming force变形deformation应力stress硬度rigidity[ri'dʒidəti]热处理heat treatment退火anneal[ə'ni:l]正火normalizing['nɔ:məlaiziŋ]脱碳decarburization[di,kɑrbjərɪ'zeʃən渗碳carburization电路circuit半导体元件semiconductor element [,semikən'dɔktə]反馈feedback发生器generator直流电源DC electrical source门电路gate circuit逻辑代数logic algebra外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch [klʌtʃ]绞孔fraising绞刀reamer ['riːmə(r)]螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement进给方向direction of feed进给运动feed movement合成进给运动resultant movement of feed合成切削运动resultant movement ofcutting合成切削运动方向direction of resultant movement of cutting切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴spindle ['spindl]主轴箱headstock卡盘chuck [tʃʌk]2加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure /haɪ'drɔlɪk]/切线tangent ['tændʒənt]机电一体化mechanotronicsmechanical-electrical integration [,inti'ɡreiʃən]气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch [klʌtʃ]离合器；控制；手；紧急关头液压泵hydraulic pump [pʌmp]阀门valve[vælv]失效invalidation强度intensity载荷load应力stress安全系数safty factor['fæktə]可靠性reliability螺纹thread螺旋helix['hi:liks]键spline[splain]销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design 有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal3陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion 车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant 逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination 气体状态方程equation of state of gas 动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism 机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel机械零件mechanical parts淬火冷却quench淬火hardening回火tempering4调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel机床行业部分英汉对照（1)：按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding fu rnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC 刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etchin g machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机5Gears 齿轮Gravity casting machines 重力铸造机Grinde r bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydra ulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column ty pe 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Millin g machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium w heels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC 高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统6Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手螺丝词汇的中英文对照六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRATED NUTS六角轮缘螺帽HEX FLANGE NUTS 高脚螺帽HEX COUPLING NUTS(HIGH NUT S)圆螺帽ROUND NUTS四角螺帽SQUARE NUTS7HEAVY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS普通六角螺帽HEX NUTS六角重型螺帽HEAVY HEX NUTS薄型螺帽HEX JAM NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS机械螺丝用六角螺帽HEX MACHINE SCREW NUT机械工具英语机械工具spanner 扳子(美作:wrench) doub le-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子(美作:socket wrench) c alipers 卡规pincers, tongs 夹钳shears 剪子hacksaw 钢锯wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子drill 钻chuck 卡盘scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规rivet 铆钉nut 螺母locknut 自锁螺母,防松螺母bolt 螺栓pin, peg, dowel 销钉washer 垫圈staple U形钉oil can 油壶jack 工作服grease gun 注油枪机械加工抛光polishing 安装to assem ble 衬套bushing外贸常用机械英语大全Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机8repair修理operator作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section 品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller 铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position 职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager 副理sectio n supervisor课长deputy section supervisor =vice section supe risor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil 擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练9proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车外贸常用机械英语大全(续) compound die合模die locker锁模器pressure plate=plate pinch压板bolt 螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list 标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/ 审核/承办PCE assembly production schedule sheet PCE 组装厂生产排配表model 机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total 合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods 处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet 栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot 导正筒trim 剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole 废料孔10feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin 定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block 衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut 剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction 感应induction light 感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex 凹short 射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit 沙砾granule=peuet=grain细粒11grit maker抽粒机cushion缓冲magnalium 镁铝合金magnesium镁金metal plate钣金lathe车mill 锉plane刨grind磨drill 铝boring镗blinster 气泡fillet 镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys 花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison 联络单volatile 挥发性resistance电阻ion 离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机机械类常用英语：生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号阀门种类英汉术语对照Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball Valves CQ螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气球12Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀Electric Actuated Wedge Gate Valves 电动楔式闸阀Electric Double Disk Parallel Gate Valve s 电动平行式双闸板闸板Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Statio n Gate Valves 高温高压电站闸阀High Temperature Pressure Power Statio n Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves 磁耦合截止阀Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵(阀) Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves 直流式截止阀Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀Pressure valve 压力（増压）阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀Restrictor Valves 过流阀(或节流阀) Safety Valves 安全阀Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀S olenoid valves 电磁阀Single Disc Flat Gate Valves 单闸板平板闸阀Single Opening Exhaust Valves 单口排气球Slurry Pumps 泥浆泵Stop Valves 截止阀Strainer 过滤器Submerged Motor Pumps 潜水电泵(排污泵)Swing Check Valves 旋启式止回阀Swing Check Valves 旋启式止回阀Tank Lorry Ball Valves 槽车球阀T-Cock 三通Thin Gate Valves 薄型闸阀Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀Triple (tee) valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵) Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning对夹式衬胶蝶阀Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套Ball 球、球芯13Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质Applicable temperature 适用温度Butt Clamp 对夹Chemical analysis 化学成份Connecting format 连接形式Double disc 双闸板Flexible disc 弹性闸板Flange 法兰Hoop 卡箍Inside thread 内螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity材料化学成份和机械性能materials 材料Materials for main parts 主要零件材料Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力Model 型号Name of parts 零件名称nitrogen (N) 氮Nominal bore 公称通径Nominal Pressure 公称压力Nozzle 排气口Outside thread 外螺纹Oxidant 氧化性介质Parallel 平行Piping 管路Piston 活塞Reductant 还原性介质Rising stem 明杆Seal 阀座，密封面Seat testing pressure 压力气密封试验压力Socket 卡套Specifications 性能规范Single disc 单闸板Solid 刚性Strengh testing pressure 强度试验压力Steam , condensate 蒸汽,凝结水Stroke 冲程，行程Water,oil,steam 水,温度,气Wedge 楔式Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜Ceramic metal 陶瓷金属Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel铬钼钒钢Chromium stainless steel 铬不锈钢Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁Hayne's alloy 钴铬钨合金High tem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene(PTEF) 聚四氟乙烯Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜14Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质机械类常用英语：钢材类alloy tool steel 合金工具钢 aluminium alloy 铝合金钢bearing alloy 轴承合金 blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢clad sheet 被覆板 clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢 galvanized ste el sheet 镀锌铁板hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢 marg ing steel 马式体高强度热处理钢martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁 merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢 prehardened steel 顶硬钢silicon steel sheet 矽钢板 stainless steel 不锈钢tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜troostite 吐粒散铁 tungsten steel ?钢vinyl tapped steel sheet 塑胶覆面钢板塑件模具相关英文compre sion molding压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston 活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle 阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板15guide pin 导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate 缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue浇口;溶渣__。
机械电气专业英语词汇
机械电气专业英语词汇英文中文Aabbreviationabrasiveabrasive-brushesabsolute Absolutepositiontransducer ACdriveACmotorAC(Alternatecurrent) accelerationaccessoryaccumulatoracidanalyzer acidcirculationtanks acidregenerationsystem across 缩写有研磨作用的、研磨粉研磨刷完好的、的确的、绝对的绝对地点变送器沟通传动沟通电机沟通电加快度附件活套酸剖析仪酸循环罐酸重生系统穿过ACS800multidriveACS800多传activateactiveactuateadequateadheringadjustadjustingdevice,electro-hydraulic adopt advancedprocesscontrollicense agglomerationagitatorairairpressuresupply airsolenoidvalveair-conditioneralarmalarm/eventsummarywindows alarmandeventlistalarmmanageralarmprioritiesalignment 激活使用开动足够的粘附调整、调理电液调整设施采纳高级过程控制赞同结块、凝集搅拌器空气压缩空气的供给空气用电磁阀空调警报报警/事件汇总窗口报警和事件表报警管理器报警优先级别摆列，对中，矫直alleyallocationofscopeofsupplyalloysteelalternatealtitudeofsiteambienttemperatureameliorate americannationalstandardsinst(ANSI) ammoniagasamplifyanaloginputanaloginputcardanalogoutputcardanaloguevaluesanalysisanalyzerangleannealinganodeanodicanswerreturncode answertelegramcodeanticrimpingrollanti-corrosiveanti-frictionbearingappendixapplication applicationandmotorcontrol applicationsoftwareapplication-dedicatedcontrolapplyapproachappropriateappurtenantarborarchitecturearmaturearrangementaspectobjectplatformassemblyassemblylineassistassumeatsite巷,小径供货分交合金钢交替,轮番的海拔环境温度改良,改良美国标准协会氨气放大、扩大模拟输入模拟量输入卡模拟量输出卡模拟量值剖析剖析员角度退火阳极阳极的应答代码应答电文代码防皱辊耐腐化低摩擦轴承附件应用电机应用控制应用软件由应用决定的控制供给靠近合适的,独有的隶属的心轴,柄轴结构电枢部署对象属性平台装置、组装、会合装置线帮助,促使假定在现场atmos=atmosphere(炉内)氛围austeniteauto automaticelongationcontrol automaticgaugecontrol automaticMode automaticslowdown automaticslowdowncrawlingspeed automaticslowdownstop automationsystem automationsystemlayout auxiliariescontrol auxiliarycontrolunit auxiliarydevice auxiliaryfunction auxiliaryPlant auxiliarypowersupplyoutput availabilityaverageavertaxialaxial 奥氏体自动延长率自动控制厚度自动控制自动模式自动降速自动降速低速自动降速停止自动化系统自动化系统部署协助控制协助控制单元协助设施协助功能公辅车间协助电源输出有效率均匀防备，移开轴向的a. 轴的axialbearing止推轴承、轴向轴承Bback–washingfiltrationback-uprollbackward balancemodeforpositioning ballvalvebanding basiccontrollicense basicdatabasiscontrol basisofthebidbatchbatchwisebatterybaybaycraneBD〔basicdesign)beambearingbearingassembly反冲刷过滤器支承辊向后、相反地点均衡模式球阀捆带根基控制赞同根本数据根基控制报价依照一炉、一批分批的，中止的电池跨行车根本设计横梁,卷轴,杠杆轴承轴承装置behind在⋯⋯后beltbelt皮bend曲折bendingforce曲折力,弯力bendingmachine弯机bendingroll弯benefit利益,受益bevelgear斜BI〔BasicInformation〕基信息billofMaterial资料清binarycontroll icense二制控制可boiler炉bolt螺栓，插bottom底box箱子bracket托架brake,制器,刹brakecontrol抱braketongs制用具brakerroll制brakingchopperunit制波器元brakingresistorunit制阻元brand商break停,打破breakage破、断裂breakerrollbridlecontrol控制bridlerollbronzebushing套(滑承) brown棕色brushroll刷bucket料斗、桶burmasher毛刺修磨机burners嘴burr毛刺burrmasher去毛刺机busbar母butt接butterflyvalve蝶button按buyer客、方Ccabinetdimensioncablecontainercabledragchaincabledrumcableexitcalculation calculationofremainingstriplength calendarTimecalibration calibrationoftheScrewdown calibrationsequencefunctioncamcameracantileverjibcranecaptioncarbondioxidecarryoutcarryovertablecartridgescascadecatcherbarcatenarycathode(conversionofdrawing)cellarcenteringdevicecentralprocessorcentralrackcentrifugalcentrifugalblowercentringSystemchamberchampchangechange-covercharacteristiccharacteristictextcheckvalvechemicalchequerdplates,chimneychopchopper 柜子尺寸缆道电缆拖链,电缆架电缆滚筒电缆出口计算,估量节余带钢长度计算日历时间校准旋动校准校准功能凸轮、偏爱轮相机悬臂梁起重机说明、标题二氧化碳执行、达成导板台框架、辊盒串连抓辊,抱紧辊悬链线阴极图纸转变地下室对中设施中央办理器机架离心的，离心力的离心风机对中系统室高声咀嚼改换可改换槽盖特征,特色字符串文本单向阀化学的格板烟囱砍切碎机circuit-breakercirculationpumpscirculationtankcivilclampclampclampclampingcleanclientclockfrequencycloggingcloseclosecoupleclosedclosedloopclosed-circuitclutchcoilcoilcarcoilcenteringdevice coildiametercalculation coildimensioncoillengthcalculationcoilopener coiloutsidediameterdetectiondevice coilpeelercoilpreparationstationcoilscalecoilweighingscalecoilercontrolcoldruntestcollapsecolorationco-manufacturecombustioncomingintoforce.commercialcommissioncommoditcommondcbusconnection commonindustrialdriveplatform communicationcommunicationboard断路器循环泵循环罐民用的、国内的加紧装置夹住,夹紧夹夹紧洁净客户端时钟频次拥塞封闭闭环封闭的闭环闭环离合器，咬合钢卷钢卷小车钢卷对中装置卷径计算钢卷尺寸卷长度计算开卷器钢卷外径丈量装置铲头机钢卷准备站称重钢卷称重装置卷取控制冷负荷试车缩短,塌卷染色、着色合作制造焚烧奏效通用的拜托，服役商品，农产品公共的直流母线连结通用的工业变频器平台信息、通信通信板communicationexpansioncommunicationmaster compactsizecompaniescomparisoncompartmentcompensate compensatedinternal compensation completesystemmanagement complycompresscompressedair compressedairaccumulator compressiveconcept通信扩展通信控制器紧凑的外观企业、伙伴比较隔间赔偿内部赔偿赔偿完好的系统管理赞同，执行压缩压缩空气压缩空气采集器压缩的n. 观点,想法condensatecondensatepump condensatetankcondensationconditionconductivety confidentialityofinformation configurationconfirmconjunctionconsecutionconstant constantcurrentcontrol constrain 浓缩冷凝水泵冷凝水罐浓缩条件电导率信息的保密结构确认、确立连结,接合连结固定、恒量常数控制v. 听从,逼迫constraintn.construction constructionfeature consulting consumptioncontain contaminationlevel contentcontentcontrol controlaccuracy controlandiO controlboxes controlcenter controlfeatures建筑物,安装构件特色咨询消耗包括，控制污介入数内容，目录，重点目录控制控制精度控制与i/O控制箱控制集中化控制特色controlfunctionscontrolgroupwindows controlnetwork controlpanel控制功能控制组窗口控制网络控制盘controlpanelCDP312CDP312操作盘controlpointscontrolprecision controlvoltagecontrollercontrollerblock controllerParameterizing convenient convertertransformer conveyorcoolantcoolingcoolingmethodcoolingspraycoolingwatercooperationcoordinationcopecorrectivecorrespondcorrosioncountercurrentcoupling coveroperationneolytepickling CPC(centerpositioncontrol) crackcradlerollcradlerollstationcranecranehookcreepspeedcrimpcropcropshearcrowncubiclecurriculumcurvescutcycle 控制点控制精度控制电压控制器控制器模块控制器参数设定方便的、便利的整流变压器传递带冷却剂、冷却液冷却冷却方式发射冷却冷却水合作、协作同样战胜赔偿，纠正相应，一致，通信侵害,腐化逆流偶连器酸洗段带防酸树脂盖对中控制裂痕,破碎支承辊〔钢卷小车地辊〕鞍座起重机吊钩爬行速度皱农作物,产量,割,废料剪凸度柜子路线，门路曲线剪切循环、周期cylinder液压缸Ddamage伤害、破坏damp湿润,湿气data数据dataaccesscontrol数据接见控制date日期DCPowersupply直流电源DC〔directcurrent〕直流电DD〔detaildesign〕详尽设计deceleration减速度defect缺点、弊端defectcode缺点代码definite明确的,有限的definition定义deflectorroll转向辊deformation变形deliberate考虑deliver交托，递交demi-pumps脱盐水泵demineralizedwater脱盐水demister除雾器脱盐水罐demi-watertankdenoxunit去氮化物单元density密度deoiler脱油装置depositn.积淀物,寄存物v.储藏,积淀depth深度descaling除锈description描绘design设计desk桌子detail细节detect发现,查出,探知=inspectdeteriorate变坏,堕落deviation离题,误差dewPoint露点diagnostic诊疗diagram图标,图样diameter直径diaphragmvalve隔阂阀digitaldisplay数据显示digitalinput数字输入digitalinputcarddigitaloutputcarddimensiondimensionaccuracyDINdiodesupplyunitdirectcoolingwater directtensioncontroldiscerndischargingdisenabledismountingdisplaydesigndisplayexampledisplayexchangetimedistanceindicator distancetransducer,positiontransducer distinguishdistributedistributedistributiondistributionsystem distributiontransformerdivertdividingsheardivisiondocumentsdosingDoubleHeadSideTrimmer downstreamsidedownworddragchaindragoutdrawingdrierdrinkwaterdrivedrivecommissioningtool drivecontrolperformance drivecontrolunitdrivesidedrivestandarddrivesystemdriveunit数字量输入卡数字量输出卡尺寸尺寸精度德国标准二极管供电单元直接冷却水直接张力控制看出，鉴识卸料、排放不能够拆卸画面设计画面样板画面刷新时间地点显示器地点〔传感器〕编码器划分分派分派分派配电系统配电变压器使转向,避开分切剪部门文件、档案剂量双头切边剪出口侧向下拖链迟延图纸乏味机饮用水传动传动调试与保护工具变频器控制性能变频器控制单元传动侧标准传动传动系统传动单元drivenrollsdriveswindowdropdrumsegment drumshaftdualductductworkduetodummydummyrolldumpdurationdustdustexhaustpipedutydynamic dynamicbrakingunit dynamictensionaccuracy驱动辊传动窗口滴扇形块鼓轮轴双导管管道系统因为模型模型辊〔代替辊〕倒,垃圾堆连续时间尘埃除尘管工作制、责任变化的，动力的动向制动单元动向张力精度E earthingearthquakeedgeedgeblow-offdevice edgepositioningunitedgescrapefficiency efficientandflexibleNavigation effluentelapseelectric&basicautomationsystem electricalpowersupplyelectro –magneticvalve electrodeelectrodeelectro-magneticbrakeelementeliminateelongation emergencypowersection emergencypowersupply emergencypowerswitch-overdistributioncubicle emergencystop接地地震端部,侧部边部吹扫装置边部定位系统边废料效率高效灵巧的导游流出流逝〔时间〕电气及根基自动化系统供电电磁阀电极、焊条电极电磁闸元素清除，忽视延长率紧迫电源局部紧迫供电紧迫电源切换的配电柜紧停emissing射receiving接收employ利用empty空emulsion乳化液enable能够enclosure保等encoder器end束energy能量engage从事工作engineering工程engineeringstandard工程准engineeringstation工程站enhancedsecurity增的安全性enterpriseresourceplanning-level3企源划-l3entrycoildata进口卷数据entrycoilNO.进口卷号entryElectricalroomlayout进口气室部署entrylooper进口活套entrypulpitlayout进口操作室部署entrysection进口段environmentallimit境要求erection安装errorESI化指数〔乳化液指之一〕essential必需的establish立estimate估,判断ethernet以太网evaporative蒸evaporator蒸器eventtext事件文本event/alarmlist急事件/警列表excess剩excessive度，极端exert施加⋯exhaust耗费，排放exhaustsystem排气系exitchain出口运exitcoilcar出口卷小exitElectricalroomlayout出口气室部署exitlooper出口活套exitproductiondata出口品数据exitpulpitlayout出口操作室部署exitsectionexpandexport extendedarchitecture extension extensivediagnostics extractextractorextreme出口段胀输出扩展的结构延长〔局部〕宽泛的诊疗系统选用,摘取抽取者尾端Ffaceplate facilitate facilityfanfastfaststop fatiguestrength fault faultfinding featuresandBene fitsfe-concentration feedback feedbackcontrol feedforward feedforwardcont rolfenceferrite fibercable fieldbuscontrol fieldDevices fieldinstrument fieldweakeningp oint filetransferpro tocolfilmfilter filterfineness final finalacceptance testfinalusefinish firefightingsystemfirmfit〔FAT〕面板使简单,便于能力风机迅速快停疲惫强度故障故障查问特征与长处铁离子浓度反响反响控制前馈前馈控制栅栏铁素体光缆现场总线控制现场设施现场仪表、弱磁点文件传输协议电影,胶卷过滤器过滤精度最后最后查收测试最后用途达成防火系统企业适合的,安装fittingfixedspeeddrives fixedspeeddriveslist flangeflapflashmemoryflashpointflatness flatnessactualvalue flatnessactuatorscontrol flatnesscontrol flattenerrolls flexiblecoupling flowmeterflowmonitor flowtransducerfluidfoldersforceforcetransducerforkliftformulaforwordfoundationBoltsfractureframe装置,配件,附件定速传动定速传动电机清单法兰拍打、漂浮闪存闪点平展度板形实绩板形控制平展度控制矫直辊弹性联轴节、缓冲接头统量计流量监督元件流量变送器流动折叠压力、力量压力变送器叉车、铲车公式、规那么向前地脚螺栓伤害,断裂机架frequence=frequency频次frequenceconverterfrequencyfreshfrictionFRPfuelfulfil fullyintegrateddirect fumefumeexhaustfunction functionblock functionblockdiagram functiondescription furnace furnaceblowers 变频器频次新鲜的摩擦、摩擦力玻璃纤维加强塑料、玻璃钢燃料执行高度集成的指令烟雾烟雾排放功能、函数功能模块功能块图功能描绘炉子炉子风机G gapgasketgaugetaperGBgeargearboxreducergearmotorgearoillubricationgearsgeneralgenerallayoutgeneraldatageneralspecification generalstructureoftheautomationsystem globevalvegramgraphicbuildergraphicssystemgreasegreaselubricationsystemsgreycastirongrippergroupalarmbandgroupjogginggroupingguaranteeguaranteefigureguardguideguillotine 空隙垫圈测厚仪国家标准传动装置齿轮减速箱齿轮电机齿轮润滑油齿轮、传动装置概括整体布局总概数据纲要说明自动化系统的整体结构球型截止阀克(g)图形编写器画面系统牛油，黄油油脂润滑系统灰口铸铁钳子、夹子报警群栏结合点动分类保证保证值防备罩指导、指导斩首,切断Hhandrailharddiskhardness hardnessvariation hardwareharmfulharmonic harmonicdistortion harmonicfilter headtracking heatcycle 栏杆、扶手硬盘硬度硬度差别,变化硬件有害的，伤害的、谐波谐波畸变谐波滤波器穿带加热循环heatexchangerheatingvalueheat-resistantheighthelicallytoothed highcurrentrectifier highperformancecommunication highpressurelamp highPressurevacuumcleaningDevice histogrammHMIHMIapplicationsoftware HMIresponsetimeHMIstations热互换器加热值耐热的高度螺旋啮合高流整流器高性能通信高压灯高压真空洁净装置棒状图人机界面HMI应用软件HMI响应时间HMI操作站hoisthoistframeholdhoodhorizonbusbar horizonbusbarratedcurrent horizontalhosehothotcommissioning hotruntesthousingposthubhumidityhydraulic hydrauliccylinders hydraulicmanifold hydraulicscrewdown hydraulicsolenoidvalve hydraulicsystemhydrogenhygienehysteresis 提高，起重，卷扬检修吊具保持罩子直流母线母线额定电流水平的软管热的热调试热负荷试车机架立柱轮轴,衬套湿度液压液压缸液压歧管液压旋下液压用电磁阀液压系统氢卫生磁滞，迟滞I.I/omodule换言之I/O模块IDidenticalidleroll内径同样的空转辊、从动辊IEC〔InternationalElectricalcouncil〕国气会IGBTsupplyunit可控晶管供元immerse侵入,陷于Import入improper不适合的、不合适的inprinciple原上inactive不再使用，不活的incline斜,斜面Incominglinecableconnection接Incominglinenumber数目Incomingunit元incorporate成，使⋯归并Incrementalencoder增量型器indicate指示，示Indirectcoolingwater接冷却水Indirecttensioncontrol接力控制Individualalarmbar个性化的警条Individualequipmenttest体inductivesensingdevice.感感器IndustrialITenabledIndustrialIT可激活industrialwater工水inertia性Inertiacompensation性Informationabouttheselectedoperationmode所操作方式Informationstorage信息存initiate惹起，，触，开始inlet进口,口inner内部innovate改革,改革input入Inputvoltage入insert插入inspectionstand台InspectionStation站Inspectorinstallations安装Instructionlist指令列表instrument工具、用具Instrumentcompartment表件instrumentation使用器InsulationclassIntegratedcorefunctions集成的核心功能Integrationandconnectivity集成和接intended划中的interchange互换、立交=change-over对换Interface接口Interfacelist接口清单Interfacewithothersystem与其余系统接口Interlock联锁Intermediateroll中间辊intermesh插入深度intermittent断断续续Internalinterlocking联锁InternationalElectroTechnicalCommission国际电气委员会InternationalStandardizationOrganization(ISO)国际标准化组织interpolation插入Intervention干涉Introduction介绍Invertercomponents变频器组件Inverterunit逆变单元item工程、条款Itemsummary工程汇总Jjack千斤顶jibcranes悬臂吊jog点动joggingfunctionality点动功能Kkey重点、键keyboard键盘kick-offmeeting开球会knife刀knifeclearance齿侧空隙Lladder梯子ladderdiagram梯型图laminate叠合lamptest灯试验lap重叠量lapposition重叠量lateralrollshifting沿轴窜移layout布局leakage泄漏、渗漏lean倾斜length长度lengthmeasurementlevel levelandPressureMonitoring levelmonitor leveltransducerlevellerlevellerdrivelevellingunitliaisonliftlift-timelubricated lightbarrierlimitswitchlineacceleration linecontrolslinesequenceslinestoplinesupplyunit linearspeedtransducerlininglinkliquidammonialistlistofpanels loadandResponseTimeofSystem loadconditionslocallocalcontrolstations localoperatordesks/boxes looperloopercontrol looperpositionscontrol looperrolllosslowvoltagelowerlubricationLVACmotor LVPowercontrolswitchgear长度检测水平液面和压力监督液位检测元件液位传感器矫直机矫直机驱动矫直系统联系、赞同提高周期润滑光栅限位开关机组加快机组控制机组次序控制主线停机机组的供电单元线性速度变送器内层、衬套连结液态氨列表、明细表盘柜清单系统负荷率与响应时间负荷条件当地、当地现场控制站现场控制台/箱环，活套活套控制活套定位活套辊损失低压降落润滑、润滑油低压沟通电机中压开关柜M magneticmagneticflowmeasurement magneticlimitswitch磁电磁性流量计磁限开关magneticseparatormainmaincolourschememainconnectionmaincontroldesksmainfeaturesmainscreenAreamainvectorgroupsmaintenancemaintenancetoolmajorprocessdatamajoritymalfunctionmandrelmanholemanipulatormanualmanualflatnesscontrolmanualModemanualSequences manufacturingexecutionsystem-level2 manufacturingmessagingspecification martensitemashmassflowcontrolmaterialmaterialhandlingmaterialhardnessmax maximumofvariablesinonetelegram mechanicmechanicalcondition mechanicalconstructionmediamediumvoltagememory磁性分离器主要、重点主要颜色配置主要连结主控制台主要特征主屏区主要联接组别维修、保护保护工具主要工艺数据主要、多半故障，疾病,失灵，误动作卷筒人孔，检查孔机械手、控制器手动、指南、手册板型控制手册手动模式手动及次序控制生产执行系统-l2现场信息规格马氏体麦芽汁秒流量控制物质，资料原料管理材质硬度最大的在一个电文中最大变量机械机械条件机械结构媒介中压内存MESBillofMaterialmeshmesser metalenclosed meteorology meter microfilm mildsteelMES资料清单网眼,啮合,捕获重叠金属防备气象学计量、仪表、米微型胶卷低碳钢,软钢milldrivemillmanagementsystem millpinionmillstand millstandelongation minmineraloilminimalminute miscellaneousequipment missingcondition mixedacid mixedAcidPickling mobile轧机传动轧机管理系统轧机齿轮轧机机架机架延长最小的矿物油最小分钟其余设施缺失条件混淆酸混酸酸洗a. 动的,易动的modemodesofoperation modify 方式操作方式改正modularwithI/OmoduleandterminationunitI/O模块和终端设施的标准组件modulemodulusofelasticitymonitormonitoringfunction monorailcranemotor motorandElectricalEquipmentlist motorconnection motorcontrolcenter motorcontroltechnology motorforreductionmillstand motorstartercontrol motorsandcomponentslistmountmountingmountingbracketmovemovestep moveableprotectioncovermultiplemushMutual MvDistributionSwitchgear 模块弹性系数、弹性模量监督器、监控器监督功能单轨起重机马达马达及电气设施清单电机接线马达控制中心电机控制技术轧机主电机电机启动控制电机及元器件清单固定件，安装、装置装置、烘托纸固定托架，平台挪动挪动一步、挪动步幅活动式防备罩多样的玉米粥互相的，共同的中压配电柜Nnarrow减小、窄的naturalgasnegative networkfilesystem neutralelectrolytical nibblernitrogenNitrogen〔N2〕noisenormalstopnotchernotenotifynozzlenumber numericaltables numerousnut天然气负的网络文件夹系统中性电解质=cutter=shear氮气氮噪声正常停止月牙剪注意通告喷嘴数目、号数表多半的螺母剪刀OobligationOCSBillofMaterial责任、义务OcS资料清单ODoffofflineanalysisoileroilingmachineononlinediagnosticsonlyopendpencontrolsystem-level1 dpenloop Openpackageinspections(OPI) operatingspeeds operatingstations operatingtime operationmodes operationPlatforms operations operatorcommands 外径封闭离线剖析涂油机、油商涂油机、加油机开在线诊疗只是打开开放控制系统-一级机开环开箱〔开包〕检查生产速度操作站作业时间操作模式操作平台操作操作指令operatorITworkstation OperateIT操作站operatorsideoperators option 操作侧操作员自由选择oscillatingoscillatingduct oscilloscopeoutoutboardbearingoutdoor outgoingcableconnection outletoutletoutputoutputproduction outputvoltageoutsideovaloveroverflowoverflowvalveoverlapoverloadoverloadatn(base/max.)振荡振荡管示波器外面外置轴承户外的出线电缆走向出口出口输出、产量产量输出电压外面椭圆的结束溢流溢流阀〔安全阀〕重叠量超载过载转速〔基速/最大〕P packagepackingtypepadpaintpaintcolorpanpaperlaminator parallel parameter participate passline passlineadjustment patentpatternpayoffreelpay-offpealpeelpeelerpeephole penetration performance包裹、包包装种类垫片、垫圈涂料、油漆涂料颜色盘、面板衬纸机平行的参数、参量参加、参加经过线边线调整专利模式开卷机开卷、打开响声剥,去去皮机窥视孔、检查孔浸透特征，行为，表现personalcomputerpersonalizedworkplaces photocellpicklingpicklingrectifier picklingsectionpilingpilotpinchrollpinch-Rollscontrol piniongearingpistonpitpivot-mountedplaceplan PlantAreasorProcessSections plantexplorerplantnetworkplantoverview planttechnicaldataplatetypeplatformplausibilityplug –in plugconnectormountedplungerpneumaticpneumaticcylinders pneumaticSystempointpositionpositioncontrol positionrecording positionsynchronization positiontransducer positioningautomaticslowdown positioningSquarerootslowdown positivepowerpowercenterpowerfactor powerfactorcompensation powerplatetechnology个人计算机个性化的工作站光电元件酸洗酸洗整流器酸洗段打桩工程驾驶、指引夹送辊夹送辊控制小齿轮传动装置活塞坑，加油站，维修站旋轴鞍座地点方案、设计图工厂地区或工艺段工厂资源管理器工厂网络画面综观工厂技术参数板式平台貌同实异的插入式插塞式固定的跳入,活塞,栓塞气动的、气压的气缸气压系统点地点地点控制地点记录地点同步地点变送器地点自动减降平方根减降正的电源配电中心功率因数电源功率赔偿功率模块技术powerrailpowersupply powersupplydiagram predesaltwaterprepicklingpreambleprecedingpreconditionspreliminary preliminaryconsumerlist premiumdrivecontroltechnology Pre-Rinsepressure pressuredifferentialmonitor pressuremonitor principlesketchprocess processcontrolfunction processcontrolHardware processgraphicprocesssectionprocessspeedprocessorprocessorcomputerproductMixproductstructure productioncapacity programHandling programmablelogiccontroller programminglanguage programmingtool programmingworkplace progressivejoggingpropaneproperpropertyproportionalvalvesproposeproprietaryprotectionclass protectionshieldprotocolproximityproximityswitch源源系脱水酸洗序言、言在⋯⋯以前、前述前提的,初步的初定用清高性能的控制技冲洗力差元件力元件原理程、工程控制功能系硬件工形工段工速度制造者〔理器〕程机品分派、品大品构生能力、能程操作可程控制器程言程工具工作站程机点丙合适的，正确的特征，性比率建、划、打算全部(者)保等防罩(盾)草案、靠近靠近开关pullpulleypulpit pulseencoderinterfacemodule pulsegeneratorpumppumppitpunchpunchholedetectorpuritypusherplatePVDF拉滑轮,皮带轮操作室脉冲编码器接口模块脉冲器泵污水坑打孔,使劲打穿孔检测器纯度推板聚偏氟乙烯Qqualificationcertificatesquality quench quenching quickstop质量证明书质量、性质熄灭,冷却淬火快停R radialradiationraiserangerate ratedoperatingvoltage ratedoutput ratedpower ratedspeed ratedvoltagereadyreasonre-circulation recoilerrecordrectifierreducerreductionmill redundancyreel referencegeneration referencevoltageoutput 放射状、半径的放射物、辐射、发散上涨、出现、提高范围额定额定工作电压额定输出额定功率额定速度额定电压准备原由再循环卷取机记录、报告、档案整流器减速器轧机冗余卷,卷轴参照值产生参照电压输出reflectionrefractionindex regeneratedacid regeneration registration regulate regulationoverview relativehumidity releaserelevantrelief remotecontrolled remotediagnostics removerenovation replacement replenish reportdisplay reportingsystem requirement reserveresidualsresortrespect responsetime restriction retightenretractreturnrevampreverseribbedtuberigidringsegmentrinserinsesection rinsewater rinsingcircuit rinsingpumps rinsingsection rinsingtank rinsingwatertank ripplerisk反射折射系数重生酸重生记录议调整调理综合图相对湿度开释相关的代替远程控制远程诊疗去除改革代替填满报表显示报表系统必需条件、需求保留,预约节余的、残留的常去,求援,依靠问候,细节响应时间限制，拘束从头旋紧缩回,回收返回维修,改良向后，相反、反转的肋片管刚性的环形片、环状扇形块漂洗漂洗段漂洗水加热循环冲洗泵冲洗段冲刷槽冲洗水罐超调风险rollrollbendingrollchangerollforcerollforcecontrol rollgapcontrolrollmarksrollabilityrollerTablerollingmill rollingmillcontrolroperotaryshearrotate rotationspeedmonitor rotationalspeedtransducer roughnessrunrunningModes轧制、轧辊辊曲折换辊轧制力辊压控制辊缝控制辊印可轧制性辊台轧机、轧钢厂轧机控制绳圆盘剪旋转转速检测元件转速变送器粗拙度运转运转模式SS-6highmillS6辊轧机saddlesafetylightbarrier sagsample saponificationvalue scalableandflexible scaleBreaker scheduleschmitspait scopeofsupply scrapband scrapchopper scrapdischargesystem scrapflap scraphandingequipment scrapremovaldevice scratchesscreenscrew 鞍座安全光栅废弛样品、试样皂化值升级性和灵巧性破鳞机进度表、时间表齿侧空隙供货范围碎边，边丝碎边剪废料办理系统废料翻板废料办理装置废料采集装置擦伤屏幕n. 螺丝钉,螺旋状物screwtightenscrewdown screwdowncylinderPosition scrubbrushmachine 旋紧压下压下缸地点冲洗漱scrubbersealsealRollscontrolsecondsection sectionsetpointhandlingfunction securitysedimentsedimentationseelingrollselectionself-configuringtopologystatus sellersemi-semi-AutomaticModesendstatussendunitsensorsensorsandfielddevices sequelquerylanguagesequencesequencecontrol sequencecontrolsystem sequencesofauxiliarysystems sequentialfunctionchartserialserverservicelifeservovalvecurrentservo-valvesetsetpointmanagementsetpointseveralspeedvaluesshapemetershearbladeshiftshiftturnshiftingshimshimplateshotblastershut –offvalveshutoff清洗器〔者〕封，锁密封辊控制秒、第二局部、节工段设定值办理安全性积淀物积淀密封辊选择自我建立拓扑状态卖方不完好，半半自动化模式传递状态传递端传感器传感器和现场设施次序查问语言连续，序列、次序次序控制顺控系统协助系统的顺控时序功能表串型效力器使用寿命伺服阀电流伺服阀设定设定值管理设定点几种速度值板形仪刀刃轮班、转移、改动轮班串动薄垫片薄垫片抛丸机截止阀封闭shutdownshuttledoorsidesideguidesidenotcher sidesupportrollcartridge sidetrimmersightglasssignsilencersimilar simplerconstruction simulate停机闸门、卷链门侧面的、旁边侧导冲边剪侧支撑辊盒圆盘剪、切边剪窥视镜签署、标志、符号消音器同样的更加简单的结构v. 仿真,模拟simultaneoussinglejogging singlesoftwareinstallprocess sitesiteconditionssizesizeintelegramsketchskimmerskin-passmillslabsledgeslowslowdownfunctionsslowdownsludgesmoothsnubberrollsocketsodiumsulphatesoftkeyareasoftwaresoftwarelicensesolenoidsolenoidvalve solenoidvalve,general solidification 齐的，同步的单机点动单个软件安装过程现场现场条件尺寸电文长短草图撇油器平坦机板坯、厚片滑轨慢速降速功能减速淤泥安稳、圆滑缓冲辊插座硫酸钠软件区软件软件赞同证线卷、螺线管电磁阀电磁阀总称n. 凝结、固化sourceProgramsspacer spareparts specialcable 源程序垫片、垫圈、隔板备品备件特别电缆。
1000个常用机电英语词汇
able [`eibl] adj.能够abnormal [b`n:m l] adj.异常abort [`b:t]中断,停止absent [`bs nt] adj. 不在的，缺少的acceleration [k.sel`rei n] n. 加速，加速度access [`kses] vt. 存取action [`k n]. 动作actuator [`ktjueit]n.操作(执行)机构,执行器address [`dres] 地址adjust [`d st] 调整，校正adjustable wrench 活扳手adjustable [`d st bl] 可调整的adjusting screw 调整螺钉adjustment [`d stment] 调节、调节装置air compressor空压机 [k m`pres] 压缩机air exhaust fan排气扇[ig`z:st] 排气，抽完air [e]风，空气alarm [`lam] 报警align [`lain] 定位，对准，调整alternating current ac 交流电 [:l`t:n t] 轮流，交替ambient temp 环境温度ambient [`mbi t] 周围的，环境的ammeter [`mit] n. 电流表，安培计amp [mp] n. 安培ampere [`mp] n. 安培amplifier [`mplifai] n. 放大器，扩音器analog input [`n l g] 模拟量输入analog output 模拟量输出analog signal 模拟信号[`n l g] [`signl]analog [`n l g] 模拟analog-to-digital a/d 模数转换 [`did it l]angle valve 角伐angle [`gl] 角度application program 应用程序 [.pli`kei n] 请求,应用arc [a:k] 电弧，弧光area [`e ri] 面积，区域arrester [e`rest] 避雷器assemble line装配线，生产线[`sembl]assemble [`sembl] 安装，组装asynchronous motor 异步马达 [ei`si n s] atomizing [`tm s.fi] 雾化attention [`ten n] 注意auto reclose 自动重合闸autoformer 自耦变压器automatic [.:t`tik] auto 自动automatic voltage regulator 自动调压器 [`regjuleit] auxiliary aux 辅助的avoid 避免,回避avometer 万用表,安伏欧表计axis 轴,轴线back pressure 背压back up 支持，备用back wash 反冲洗baffle 隔板bag filter 除尘布袋balance 平衡,称，天平ball 球bar 巴，条杆base 基础、根据battery[`b t ri] n. 电池bearing brg 轴承bell 铃belt tension 皮带张力belt 带，皮带bi rate n.比特率[bai reit]binary 二进制，双bit 比特（二进制）black 黑色blade 叶片bleed 放气，放水blow 吹blown 熔断的blue 蓝色boiler blr 锅炉bolt 螺栓、拧螺丝boolean n. 逻辑boost bst 增压，提高boost pump bp 升压泵bore 孔，腔both 双方，两者都bottom 底部bracket 支架，托架，括号brake 刹车，制动器，闸break 断开，断路、破裂、折断breaker coil 跳闸线路breaker 断路器，隔离开关brown 棕色brush 电刷，刷子bucket 斗，吊斗buffer n. 缓冲器bump 碰，撞击burner 燃烧器busbar 母线button 按钮bypass/by pass byp 旁路byte 字节（八位）cabinet 厨柜，机箱、柜cable 电缆calculator 计算器caliber 管径、尺寸、大小cam 凸轮cancel 取消、省略capacitance [k`p sit ns] n. 容量，电容capacitor [k`p sit] n. 电容器＝capacitator card （电子）板、卡carton 纸板箱casualty 人身事故、伤亡、故障caution 注意center 中心central control room 中控室central processing unit cpu 中央处理器centrifugal fan 离心风机centrifugal 离心的change 改变character 字符charge indicator 验电器、带电指示器:d充电，电荷chassis earth 机壳接地chassis 底座、机壳check 检查chimney 烟囱、烟道circuit [`s:kit] n. 电路circuit breaker 电路断路器circuit diagram 电路图circuitry [`s:kitri] n.电路，线路circulating water pump 循环水泵circulating 循环clamp 夹具、钳class of insulation 绝缘等级class 类、等级、程度clean 清洁的、纯净的cleanse 净化、洗净、消毒clearing of fault 故障清除clockwise 顺时针、右旋的clogged 障碍，塞满，粘注close 关闭closed-loop 闭环coarse 粗的、不精确的code 代号、密码coder 编码器coil [k il] n.线圈cold 冷collect 收集colour 颜色command 命令、指挥communication 通信、通讯compensation 补偿，矫正component 元件compress air 压缩空气compress 压缩compressor 压缩机computer 计算机condensate 冷凝、使凝结condition 条件、状况、环境conduct 传导conductivity 导电率conductor [k n`d kt]n.导体，导线configure 组态congealer 冷却器、冷冻器connect 连接connection 联接connector 联接器、接线盒console 控制台constant 恒定的contact [`k nt kt]n.接触,触点,vt.接触,联系contact to earth 接地、触地、碰地contact 触点contactor （电流）接触器、触头continuous 连续的control cntr/cntpl 控制control panel 控制盘control valve 调节阀controller 控制器convert [k n`v:t]n.转换 vt.使转变，转换…. conveyor 传送带，输送机cooktop [`kukt p] n.炉灶cool 冷的cooler 冷却器cooling fan 冷却风机cooling tower 冷却塔cooling water pump 冷却水泵cooling 冷却copy 拷贝core 铁心、核心、磁心correct 正确的,改正correction 修正、改正corrosion 腐蚀cost of fuel 燃料费用counting [`kaunti] n.计数器couple cpl 联轴器crane 起重机curdle 凝固currency 流动、流通current n. 电流，水流、当前、气流current transformer ct 电流互感器cursor 光标curve 曲线cutter 切削工具ccycle 循环、周期、周波cylinder cyl 汽缸，圆柱体cymometer 频率表，频率计damage 损坏、破坏danger zone 危险区danger 危险、危险物dangerous 危险的dank 潮湿data base 数据库data pool 数据库data 数据deactivate 使无效dead band 死区debugging [di:`b gi] n.调试deceleration n. 减速，减速度decrease dec 减少deep 深度、深的、深default [di`f:lt] n. 默认(值),缺省(值) degree 度、等级delay time 延时delay 延迟delete 删除defective 有缺陷的description 说明、描述detect 发现、检定detector 检测器，探测器deviate 偏离、偏差device 设备、仪器diagnosis 诊断diagram 图形、图表diameter 直径dielectric 介质、绝缘的diesel generator 柴油发电机differential 差别的，差动的，微分differential pressure dp/dsp 差压digital input/output 数字量输入／输出digital signal 数字信号[`did itl][`signl] digital 数字的digital-to-analog d/a 数／模转换direct current dc 直流（电）disassembly 拆卸disaster shutdown 事故停机disaster 事故、故障discharge 排除、放电、卸载disconnect switch 隔离开关disconnect 断开,分离disconnector 隔离器、隔离开关discrete [dis`kri:t] adj.不连续的,离散的discrete input 开关量输入discrete output 开关量输出disk 磁盘diskette 磁盘，磁碟display 显示、列屏dissipation [.disi`pei n] n. 分配，分发distance 距离，间隔distilled water distl wtr 蒸馏水distributed control system dcs 集散控制系统distributed 分布的distributing board 配电盘double 两倍的，双重的dowel pin 定位销down 向下的,向下download 下载downtime 停机时间drain drn 疏水、排放drawing 画图.制图 ,图样、牵引drill 钻孔、钻头、钻床drive nail 钉钉子drive 驱动、强迫drop 站dry 干、干燥duct 风道、管道dust catcher 除尘器、吸尘器dust 灰尘duty 责任dynamic 动态的dynamometer 功率表earth connector 接地线、接地earth fault 接地故障earth lead 接地线、接地earth 大地eccentricity 偏心、扰度edit 编辑efficiency 效率ejected 喷射，驱逐，被放出的ejection 弹出，排出，喷出，喷射electric failure 触电electric spark 电火化electric 电的electric 电的、电动的、导电的electrical machine 电机electrical service 供电electrical 电的、电气的electric-hydraulic control 电／液控制electrician 电工electrode 电极electronic 电子的、电子学的electrostatic 静电的electrotechnics 电工学、电工技术element 元件、零件、单元elevation elev 标高elevator [`eliveit] n.电梯,升级机emergency emerg 紧急事故empty 排空enable 使能够，允许enclosure [in`kl u] n.密封，外壳，包围encoder 编码器end cover 端盖end 末端、终结energy meter 电度表energy 能、能量engineer 工程师enter 开始、使进入entry 输入equipment 设备error 错误escape valve 安全阀event 事件exceed 超过excess 超过、过度exciter 励磁机exit 出口expansion exp 膨胀explosion 爆炸external 外部的、表面的extinguisher 灭火器extra-high voltage 超高压factor 因素、因数factory 工厂、制造厂failure fail 失败,故障false 假的、错误的fan 风扇、风机fault 故障faultless 没有缺陷、完美的faulty operation 误操作features 特点feed 馈、供给feedback 反馈fiber optic 光纤field [fi:ld] n.现场，原野file 文件、锉刀fill 装填filter [`filt] n. 过滤器，滤波器，滤网，filter differential pressure filtr dp 滤网压差final 最后的fire pump 消防水泵fire 燃烧、火焰fire-extinguisher 灭火器fireproof 防火的、阻燃的fixed 固定的、固定、确定、保护屏flank 侧翼、侧面flash lamp 闪光灯flash light 闪光flash 闪光、闪烁、闪蒸float-charge 浮充电flow 流量、流动flowmeter 流量计flue gas 烟气flue 烟道fluid 液体flux n. 流量，通量forbid 禁止force draft fan 送风机force 强制form 形式、形状、形成、构成format 形式、格式frequency 频率friction n. 摩擦，摩擦力from 从、来自full speed 额定频率fully 充分的、完全的fume 烟，冒烟function 功能fuse holder 保险盒fuse 保险丝、熔断器fusible cutout 熔断开关gauge 仪表、标准gear pump 齿轮泵gear shift housing 变速箱gear 齿轮gearbox 齿轮箱gen main breaker 发电机出口总开关general control panel 总控制屏generator [`d en reit]n. 发电机gland seal 轴封glass-paper 砂纸go on 继续goal 目的、目标govern vlv gv 调速器、调节器graphics 调节阀grease 图形green 绿色ground/earth 地、大地guide 领路人、向导half 一半、一半的halt instruction 停机指令halve [ha:v] vt. 二等分，平分hammer 锤子hand 手，指针handle [`h ndl] vt.触摸,运用,买卖,处理,操作 vi.搬运,易于操纵handwheel 手轮，驾驶盘hardware 硬件havoc [`h v k] n.严重破坏 vt.损害heat 热、加热heater 加热器heating 加热hertz hz 赫兹high pressure hp 高压history 历史hold 保持hopper 漏斗、料斗hori vib(vibration) 水平振动hose 软管、水龙带hot circuit 通电线路hot start 热态启动hot 热的hydraulic 液压i/o point 输入/输出点inboard 内侧idle 空载的、无效的ignitor 点火器impedance 阻抗import 进口、引入impulse 脉冲、冲击、冲量inch in 英寸inching 缓动、点动increase inc 增加increment 增量index 索引、指标，指针，指数indicate 指示，表明indicator 指示器inductance 电感induction motor 异步电动机inductive reactance 感抗inductor [in`d] n.电感器，感应器inhibit 禁止init 起始，初始化initial 初始的，最初的inlet 入口input/output i/o 输入／输出insert 插入inside 内侧、内部inspection 观察、检查inspector [in`spekt] n.检测install 安装instruction [in`str k n] n. 指令，指导，指示，说明书，instrument panel 仪表盘instrument 仪器insufficient 不足的，不够的insulate 绝缘、绝热、隔离insulation 绝缘insulator [`insjuleit] n.绝缘体integer 整数integral 积分interface [`int.feis] n.分界面,界面,接口interface 接口interference 干扰、干涉intermediate relay 中间继电器internal 内部的interrupt 中断into 向内、进入inverter 逆变器、反向器、非门isolator 隔离、刀闸job 工作jumper 跳线、跨接junction box 接线盒key 键销、钥匙、键槽keyboard 键盘kilovolt-ampere kva 千伏安kink 弯曲、缠绕knack 技巧、窍门、诀窍knife-switch 闸刀开关label 标号、标签，商标，标志laboratory 实验室ladder diagram 梯形图ladder logic diagram 逻辑梯形图ladder 梯子、阶梯lamp [l mp] n.灯、光源last 最后的leak 泄漏（动词）leakage [li:kid] n. 漏，泄漏，渗漏least 最少的、最小的left 左length 长度level 液位、水平lever 杆,杠杆,控制杆lifebelt 安全带、保险带lift 提、升light run 空转light 光亮、点、点燃、照亮lightning arrestor 避雷器lightning 雷电limit lmt 极限、限制limit switch [`limit] 限位开关limiter 限制器、限位开关line 线、直线list 列表、目录liter 公升little 小的，少许，少的load [l ud] n. 负荷，负载load thrown on 带负荷local attendant 现场值班员local repair 现场检修local 局部location 处所、位置lock 闭锁、密封舱、固定logger 记录器、拖车logic 逻辑long 长loop 环、回路loose 松的、不牢固的loosen 松开、松动loss 损失、减少low 低lower 较低的、降低low-half 下半lub oil pump 润滑油泵lub oil 润滑油lubricate lub 润滑machine 机器,机械magnet 磁main wire 电源线main 主要的/主蒸汽的/电力网maintain 维修、维持、保养maintenance manual 检修手册maintenance 维护、检修、小修major overhaul 大修make 制造 ,是成为make sure 确定make up 补充（补给）malfunction 故障,出错、误动、失灵management 管理、控制、处理man-machine interaction 人机对话man-machine interface mmi 人机接口manometer 压力表manual reject mre 手动切换manual 手动、手册manual/auto station m/a station 手动／自动切换站mark 型号、刻度、标志、特征master control room 主控室、中央控制室master 主要、控制者material [m`ti ri l] n. 材料，原料maximum 最高的、最大mean 平均值、中间的measure 量度、测量，尺寸mechanical trip vlv 机械跳闸阀mechanical 机械的、力学的mechanism 机械、力学、方法、装置、机构medial 中间的、平均的medium 中间的、中等的、装置、介质、工质melt 溶解，熔化memory 存储menu [`menju:] n. 菜单metal 金属meter [`mi:t] n.仪表，米，表meter switch 仪表开关method of operation 运行方式method 方法、规律、程序microphone 麦克风、话筒microprocessor [maikr u`pr uses] n.微处理器middle mid 中间的mill 磨、磨煤机、铣刀mind 头脑、精神、介意minimum 最小的minor overhaul 小修minute 分钟misfill 误装mishandle 胡乱操作、误操纵misread 错读misreading 误读、错读miss operation 误动作、误操作mistake 错误、事故mixer n. 搅拌器，搅拌机，混合器modem 调制解调器modify 修改、更改modulating valve 调节阀module [`m dju:l] n.模块，组件，模数moisture 湿度、湿汽mold 模具monitor [`m nit] n.监听器，监视器，监控器 vt.&vi.监控month 月more than 超过motor mtr 马达motor winding 电动机组绕组mount 安装、固定mountain cork 石棉mouse 鼠标move 移动multimeter 万用表nail 钉子、钉钉子naught line 零线neck 颈，管颈needlepoint vlv 针阀negative pressure neg press 负压negative 负的neon tester 试电表network 网络neutral line 中性线neutral point 中性点newly 最近,重新、新地nipper 钳子、镊子no touch relay 无触点继电器noise remove 消音器noise 噪音no-loading 空载nominal power 额定功率nominal 标称的、额定的normal closed contact 常闭触点normal 正常的、常规的normally 正常地not available 无效、不能用nozzle 喷嘴number 数字、号码、数目nut 螺母、螺帽occur 发生ohm [um] n.欧姆oil breaker 油开关oil gun 油枪oil level 机油平面oil 油oiler 注油器oilless 缺油的on/off 开／关online 联机的，在线的open circuit 开路open-loop 开环operating panel 操作盘operation 操作、运行operational log 运行记录operator keyboard 操作员键盘operator station 操作员站operator 操作员option switch 选择开关optional 可选的orbit [`轨道，轨迹orientation 方位，定向，定位original 初始的、原始的out 出、出口outboard 外侧的outage 停用outlet 出口output 产量、产品、输出oven [`vn] n.烤箱over current 过流over loading 过载over voltage 过压over 结束,上面的,过分的overcool 过冷overflow 溢流overhaul 大修overhead 顶部overheat 使过热overload [`uv`l ud]n.过载overload protection 过载保护package 组件、包packaging [`p kid i] n.包装packed group 组合组panel 屏、盘parameter 参数part 部分、部件password 口令peak 峰值percent pct 百分数percentage 百分比perfect 完全的、理想的performance 完成、执行、性能periodic inspection 定期检查periodic 周期的、循环的peripheral equipment 外围设备peripheral 周围的，外围设备，周边的permanent 永久的、持久的permit 允许pg 编程器phase not together 缺相、失相phase ph [feiz] 阶段、状态、方面、相phase sequence 相序phase voltage 相电压phase-failure protection 断相保护phase-in 同步photoelectricity 光电pid drawing 流程图piezometer 压力计pilot 导向、辅助的、控制的pipe 管、管道plan 计划plant 工场、车间plastics 塑料plc(programmable logic controller) 可编程序逻辑控制器pliers 钳子、老虎钳plug socket 插座plug 塞子、栓、插头plus 加pneumatic 气动的point 点pointer 指针pole 机、柱pollution 污染portion 一部分position pos 位置potential transformer pt 电压互感器power failure 停电power pwr 功率、电源ppi(point-to-point interface)点对点接口preblow 预吹precipitator preci/precip 除尘器preferential n. 优先的，优先权perform 预先形成，预制，预成型坯，粗加工的成品preheat 预热preheater预热器preliminary 准备工作present 出现preset 预设、预置press 压，按，压力pressure pres 压力primary 初级的、一次的principle 原理、原则printer 打印机probe 探头process 过程、方法production 生产、产品、作品program 程序programmable [`pr ugr m bl] adj.可设计的，可编程的prohibit 禁止proportional / integral / derivative pid 比例／积分／微分protection prot 保护、预防protocol [`pr ut k l] n.协议pull 拖 ,拉pulse 脉冲、脉动pump body 泵体pump 泵purge 净化、吹扫push and pull switch 推拉开关push button 按钮push 推pushbutton [pu`b tn] n. 按钮pyod 热电偶quality 质量quit 停止、离开、推出rack earth 机壳接地radiation fin 散热片radiator [`reidieit] n. 散热器，冰箱raise 升高range 范围、量程rate 速度，速率rated power 额定功率rated 额定的、比率的ray 光线、射线read out 读出、结果传达reading 读数real power 有效功率real time 实时的receive tank 回收箱、接收箱recipe 处方、配方reclosing 重合闸recovery time 恢复时间recovery 恢复、再生rectification 整流、检波、调整rectifier [`rektifai] n.整流器，矫正器red 红色reduction 还原、缩小、降低redundancy 冗余、多余reference ref 参考、参照、证明书reflux 倒流、回流register 寄存器regulate 调节、控制relay [`ri:lei] n. 继电器release 释放reliability 可靠的、安全的relief 去载、卸载、释放、解除relieve valve 安全阀、减压阀remove 除去、拆卸renewal 更新、更换repair 修理repairer 修理工、检修工repeat 重复、反复replace 重新、启动、更换、替换replacement parts 备件、替换零件request reo 请求require 要求reserve parts 备件reserved 备用的reset 复位resist [ri`zist] n.阻抗resistance n.电阻、阻抗resolution n. 分辨率response 响应restart 重新启动retighten 重新紧固retract 可伸缩的、缩回return oil 回油return 返回reverse rotation 反转rig 安装、装配、调整right 右right-of-way 公用线路ring 环roller 滚筒、辊子rotary switch 转换开关rotating 旋转rotation 旋转，转动，回转rotor 转子routine 例行的、日常的routing inspection 日常检查、日常检测routing maintenance 日常维护rubber 橡胶run back 返回run 运行safe 安全的、可靠的、稳定的safety cap 安全帽safety 安全sample 取样、举例sampling 采样、抽样、取样saw 锯scale 刻度、衡量、比例尺、测量、铁锈水垢scan 扫描schedule 时间表、计划表screen 屏幕screw driver 螺丝刀screw socket 螺口插座screw 螺杆、螺丝、旋转seal 密封search 寻找、查找second 秒、第二seep 渗出、渗漏seepage 渗漏现象select 选择selector 选择器self-hold 自保持self-running 自启动sensitive 灵敏器sensor 传感器sequence 顺序、序列serbice manual 维修说明书series [`si ri:z] n.连续，串联service 维修.保养.服务、伺服servo 伺服servomotor 伺服电机set up 安装、调整、建立set 设定shadow 影子、屏蔽shaft 轴、手柄、矿井shake 摇动、振动shakeproof 防振shaped 形状share 共享、分配sheet 表格、纸张shell 壳shield 屏蔽层shift 值、替换shock 震动,使受电击short circuit 短路short 短的、短路、使短路should 应该,将要show 展览,显示,指示shut off 关闭shut 关上，更加shutdown 停止、停机siccative 干燥剂side 侧边siemens[.si:m z] 西门子sifter 筛子、滤波器sign 标记、注册signal lamp 信号等signal 信号silence 消音、沉寂simulation [.simju`lei n]n.仿真，模拟simulator 仿真机single blade switch 单刀开关single 单个的、个体的site 现场size 尺寸、大小sketch 图纸、草图skip 空指令、跳跃slag 结垢smoke 烟、冒烟smokes-stack 烟囱smooth 平滑的、光滑的socket wrench 套筒扳手socket 插座software 软件solenoid 电磁线圈solid wrench 呆扳手solid 固体、坚固的、固体的source 源、电源spanner 扳手spare 备用的、空余的spare parts 备件、备品spark 火化special tool 专用工具special 特别的、专门的specification 技术说明speed 速度spray nozzle 喷嘴spring clutch 弹簧离合器spring 弹簧、春天stack 烟囱stall 停车、阻止standard 标准standby 备用、待机star connected system 星形连接制y star 星、星形连接start up 启动start 启动、开始starter [`st:t]n.启动器，启动钮starting conditions 启动条件start-up sequence 启动程序state 状态statement 说明、语句station 站、发电厂、地点stator coil 定子线圈stator core 定子铁芯stator定子status display 状态显示status 状态steadiness 稳定性steam stm 蒸汽step 步，步幅step-by-step motor 步进电动机step-down transformer 降压变压器step-up transformer 升压变压器still 仍然，还，更stop 停止storage battery 蓄电池storage 储存strainer 滤网stretching 拉伸，伸长suction pump 真空泵superheater 过热器supply 供给support 支持、支撑sure 确信的、可靠的switch [swit] n. 开关，电闸switch blade 开关闸刀switch 开关、切换switching off 断开switching on 接通switching push button 开关按钮symbol 符号synchro 同步，同步机synchronization 同步synchronizer 同步器syren 汽笛、报警器syringe 注油器system unit 主机system 系统tab 表格tachogenerator 测速发电机tandem 串联tank 箱temperature compensation 温度补偿temperature liming relay 热继电器temperature 温度tensile 拉力的、张力的tension 压力、拉紧、张力terminal [`t:minl] n. 终端，接线端，电路接头test 检测、试验tester 检测者、检测器text 出口thermal conduction 热传导thermal couple 热电偶thermal 热的/热量的/由热驱动的thermometer 温度计thermostat 自动调温器，稳定调节装置，恒温器throttle 节流thrust 冲击、推力thyristor 晶闸管tight 紧密的、紧固的tighten 扣紧、变紧tilting 摆动time-lag relay 延时继电timing [`taimi] n.计时器,定时器tin soldering 焊锡t-junction 三通toggle switch [`togl] 拨动开关token 标志tong-test ammeter 钳式电流表tool box 工具箱tool 工具torque wrench 扭力扳手torque 扭矩、力矩total 总计的training officer 培训主管transducer xducer 传感器、交流器，变频器transfer 转换transformer xformer 变压器，传感器，发送器transmission 传输transmitter xmiteer 变送器transwitch 可控硅开关travel 过程、运转、进行、移动trigger 触发器trip 跳闸、断开tri-way vlv 三通阀trouble 事故、故障、干扰true 真实的、调整、校正try 尝试试图努力tune 调节tuning 调谐turn 转动、转向tweezers 镊子、钳子twist drill 麻花钻type 类型、标志u-bolt u形螺栓unbolt 取下螺栓unclean 脏的underground cable 地下电缆undervoltage 欠压、电压低uninterrupted power supply ups 不间断电流unit 单元、机组、电池unload 减负荷unlock 打开、解锁、释放unprotected 未保护的、无屏蔽的untight 松动的up 向上update 更新、修改、校正upgrade 升级(优先级）提高/改进up-half 上部、上半upper 上部use 使用user 用户uninsulate 不绝缘vacuum [`v kju m] n. 真空，空间，真空吸尘器vacuum pump 真空泵valid 有效地、正确valley load 低谷负荷value 数值valve [v lv] n. vlv 阀valve disk 阀芯valve seat 阀座vane 叶片variable 变量variator 变化器，变速器v-belt 三角皮带ventilation vent 通风ventilator 通风机，风扇，通风设备vertical vert 垂直的vessel 容器vibrate （使）震动，摇摆vibration 振动video display unit vdu 显示器vise n. 老虎钳vision 视觉，视力，显示visor 护目镜、观察孔voltage [`vaultid] n. 电压，伏特数voltage drop 电压降[`v ultid]voltage transformer 电压互感器voltmeter [`v ult.mi:t] n. 电压表volume 容积、体积wall temp 壁面温度warning 报警wash 洗washer 垫圈、补垫waste 浪费、废物watch 手表,注视watchdog看门狗water wtr 水wattage [`w tid] n. 瓦特数wear 穿,磨损weather plug 消防栓weather 天气week 星期、周weight 重量weld 焊接wheel 轮，车轮，轮子，转盘while 一会儿white 白色winch 卷扬机.windbox 风箱windings 绕组windows 窗口wire stripper 剥线钳wire 电线、金属丝、接线without 没有,不wood 木、木制的word 字，词work 工作workshop 车间，工场worm drive 蜗杆转动worm 涡轮、螺杆wrench 扳手，拧wrong 错误的、失常的wye y形接法wye-delta y－△接法year 年yellow 黄色zero drift 零点漂移zero 零zone 区、层、带zoomar 镜头。
机械专业英语词汇很全
机械专业英语词汇很全机械专业英语词汇很全，涵盖了机械工程的各个方面，包括机械设计、制造、加工、控制等。
以下是机械专业英语词汇的一些示例：1. 机械设计 Mechanical design2. 机械制造 Mechanical manufacturing3. 机械加工 Mechanical machining4. 机械控制 Mechanical control5. 自动化 Automation6. 数控机床 CNC machine tools7. 机器人 Robots8. 机床数控化 CNC of machine tools9. 工具机机床 Machine tool machines10. 机械加工工艺 Mechanical processing technology11. 精密制造 Precision manufacturing12. 物料加工 Material processing13. 金属材料 Metal materials14. 金属加工 Metal processing15. 材料力学 Material mechanics16. 工程力学 Engineering mechanics17. 流体力学 Fluid mechanics18. 热力学 Thermodynamics19. 机械结构 Mechanical structure20. 机械传动 Mechanical transmission21. 机械制动 Mechanical brake22. 机械力学 Mechanical mechanics23. 工程制图 Engineering drawing24. 机械工程师 Mechanical engineer25. 机械工厂 Mechanical factory26. 机械设备 Mechanical equipment27. 机械零件 Mechanical parts28. 机械元件 Mechanical components29. 机械系统 Mechanical system30. 机械工艺 Mechanical technology31. 机械原理 Mechanical principle32. 机械参数 Mechanical parameters33. 机械性能 Mechanical properties34. 机械加工设备 Mechanical processing equipment35. 机械加工工具 Mechanical processing tools36. 机械制造设备 Mechanical manufacturing equipment37. 机械零件加工 Mechanical parts processing38. 机械零件设计 Mechanical parts design39. 锻造工艺 Forging technology40. 冲压工艺 Stamping process41. 铸造工艺 Casting process42. 加工精度 Machining accuracy43. 材料成型 Material forming44. 液压传动 Hydrodynamic transmission45. 自动控制 Automatic control46. 机械加工质量 Mechanical processing quality47. 工艺创新 Technological innovation48. 机械设计师 Mechanical designer49. 机械制造商 Mechanical manufacturer50. 机械公司 Mechanical company以上仅是机械专业英语词汇中的一部分，还有很多更加专业的术语和技术语言，仅仅掌握这些词汇远远不够。
机械电气专业英文词汇
名板name plate 电磁触点magnetic contactor 备件备品配件spare parts 按钮push button电气设备electric equipment 安全绳safety rope速度speed 电源power source转速revolution r.p.m 过载、超载overload电机容量motor capacity 转子rotor盖板cover 定子stator法壬盘flange 滚珠轴承ball bearing unit轴shaft 滑动座slide base电磁阀solenoid valve 外壳，罩casing压力开关pressure switch 把手handle限位（行程）开limit switch 安全罩safety guard关温度开关temperature switch 伸缩管挠性管flexible tube浮动开关float switch 控制电机control motor导管conduit 连接connection联轴节coupling 频率frequency防松螺母、对关lock nut 电机清单motor list螺母电缆管cable duct 连锁流程图Interlocked flowsheet零件清单parts list 方框图block diagram电机座motor base 流程图Flow sheet电机盖motor cover 电机型号motor type磁断线圈magnetic brake coil 额定功率rating KW插塞式保险丝plug fuse 自动控制盘automatic controlpanel装置设备。
最全的 电气 & 机械 专用名词 中英对译
电气专业英语词汇——中英对照表AAbnormal 异常Accuracy 精度ACSR = aluminum conductor steel reinforced 钢芯钻铰线adjustment 调整adjustable range 可调范围fine adjustment 细调rough adjustment 粗调air gap 气隙alarm 报警alarm bell 警铃alarming window 报警窗口ampacity 载流量ampere 安培kilovolt ampere 千伏安amperemeter 安培表，电流表amplifier 放大器announciator 报警器anode 阳极anti-corrosion 防腐蚀anti-pumping device 防跳装置AOL = aircraft obstruction lamp 航空障碍灯low intensity AOL 低光强航空障碍灯high intensity AOL 高光强航空障碍灯AQR = automatic reactive power regulator 自动无功功率调整器arcing chamber 灭弧室armature 电枢ASS = automatic synchronizing system 自动同期系统asynchronous 非同期non-asynchronous capability 非同期能力Bballast 镇流器ballast-factor 镇流器系数ball eyes 球头挂环battery 蓄电池Cd-Ni battery 镉-镍蓄电池lead-acid battery 铅-酸蓄电池maintenance free battery 免维护蓄电池battery capacity 蓄电池容量battery rack 电池架battery room 蓄电池室end battery 端电池BIL = basic insulation level 绝缘基本冲击耐压水平blocking diode 闭锁二极管box 盒，箱cast aluminum junction box 铸铅接线盒cast Ferro alloy junction box 铸铁合金接线盒junction box 接线盒lead box 出线箱maintenance box 检修箱marshalling box (总配线箱)power supply box 动力箱terminal box 端子箱test box 试验盒normal lighting box 工作照明箱breaker 断路器close the breaker 合断路器open the breaker 打开断路器breaker compartment 断路小室PT circuit broken PT回路断线brush 刷graphite brush 石墨碳刷brush holder 刷握brush supporter 刷架brushless excitation system 无刷励磁系统bus 母线branch bus 分支母线by-pass bus 旁母main bus 主母线bus tie 母联flexible busbar 软母线hard busbar 硬母线miniature busbar 小母线tubular busbar 管型母线changeover busbars 倒母线bushing 套管oil filled bushing 充油套管seal-off bushing 密封套管wall bushing 穿墙套管bushing lead terminal 套管端子button 钮子push button 按钮self-holding push-button 自保持按钮turn button 旋钮buzzer 蜂鸣器Ccabinet 柜control cabinet 控制柜distribution cabinet 配电柜cable 电缆3 cores cable 三芯电缆armoured cable 铠装电缆coaxial cable 同轴电缆control cable 控制电缆copper wire braid shield cable 铜编织线屏蔽电缆fiber-optical cable 光纤电缆fire resistant cable 耐火电缆flame retardant cable 阻燃（难燃）电缆heat tracing cable 伴热电缆heating cable 加热电缆heating sensitive cable 热敏电缆high voltage oil-filled cable 高压充油电缆impregnated paper insulated cable 油浸纸绝缘电缆lead covered cable 铅皮电缆mineral insulated cable 无机绝缘电缆overhead cable 架空电缆power cable 动力电缆signal cable 信号电缆stranded copper cable 铜铰线电缆telephone cable 电话电缆triple-core cable 三芯电缆twin-core cable 两芯电缆unarmoured cable 非铠装电缆communication cable 通讯电缆single-core cable 单芯电缆tag of cable 电缆标牌cable clip 电缆夹flexible cable conduit 电缆软管cable conduit 电缆管cable head 电缆头1cable laying 电缆敷设cable laying & list 电缆敷设及清册cable mezzanine 电缆夹层cable raceway system 电缆通道系统cable rack 电缆支架cable shaft 电缆竖井cable support 电缆支架cable suspender 电缆吊架cable terminal 电缆终端头cable tray 电缆桥架cable trench 电缆沟cable tunnel 电缆隧道cable vault 电缆夹层control cable with copper tape shield 铜带屏蔽的控制电缆call 呼叫call back 回叫call signal 呼叫信号external calling 外部呼叫internal calling 内部呼叫calling 主叫detail calling record 呼叫详细记录candle power distribution curve 配光曲线capability 能力out-of-phase breaking capability 失步开断能力pressure relief capability 压力释放能力rated closing capability 额定关合能力short-line fault breaking capability 近区故障开断能力transient overvoltage capability 暂态过电压能力capability of switching long no-load line 分合长空载线路能力capability of switching no-load transformer 分合空载变压器能力capacitance 电容adjustable capacitor 可变电容器shunt capacitor 并联电容器voltage sharing capacitor 均压电容器capacitor 电容器capacitor divider 电容分压器capacity 能量,容量current carrying capacity 载流能量spare capacity 备用容量cavity ratio 室腔比cell jar 电瓶chain link 挂环changeover 切换automatic changeover 自动切换star-delta changing device 星角切换装置charge 充电equalizing charge 均衡冲电float charge 浮充电fully charged 全充charger 充电器boost charging voltage 大充电压initial charging voltage 起始充电电压check phase order 核对相序circuit 电路，回路auxiliary circuit 辅助回路follow-up circuit 跟踪回路main circuit 主电路short circuit plate 短路板spare circuit(feeder) 备用回路series circuit 串联电路circuit breaker 断路器air circuit breaker 空气断路器bus tie circuit breaker 母联断路器by-pass bus circuit breaker 旁路断路器current-limiting circuit breaker 限流断路器earth leakage circuit breaker 漏电开关field circuit breaker 磁场开关oil circuit breaker 油断路器residual current circuit breaker 漏电开关sectionalized circuit breaker 分段断路器SF6 gas insulated circuit breaker 六氟化硫断路器frame-type circuit breaker 框架式断路器clamp 线夹strain clamp 耐张线夹suspension clamp 悬垂线夹clearance 带电距离clip 线夹quick clip 快速线夹closing 合闸open phase closing of breaker 非全相合闸closing pulse 合闸脉冲coil 绕组arc-suppression coil 消弧线圈armature coil 电枢绕组holding coil 保持线圈redundant trip coil 双跳闸线圈reset coil 复归线圈shunt excitation coil 分励线圈trip coil 跳闸线圈combined 综合combined filter 综合滤波器combined starter 综合起动器commission 调试communication 通信communication building 通信楼communication line 通信线communication monitoring 通信监听dispatching communication system 调度通信系统intra-plant communication system 厂内通信系统wireline communication system 有线通信系统component 分量fundamental component 基波分量harmonic component 谐波分量conductor 导体high conductivity 高导电率composite conductor 组合导线flexible conductor 伸缩节flexible conductor 软导线conductor cross-section 导体截面conform to 符合connection 连接，接线double bus connection 双母线接线open-delta connection 开口三角形连接star connection 星形连接zigzag connection 曲折形连接1 and 1/2 circuit breaker connection 1个半断路器接线connection pin 连接端子connection plate 联接片double bus connection with bypass 双母线带旁路接线end connector 终端接头power connector 电源接头removable connector 可拆接头oil conservator 油枕contact 触头arcing contact 弧触头arcing-extinguishing contact 灭弧触头2common alarm contact 公用报警接点electrical independent contact 无源接点main contact 主触头moving contact 动触头normally closed contact 常闭接点normally opened contact 常开接点stationary contact 静触头auxiliary contact 辅助触头contactor 接触器electromagnetic pneumatic contactor 电磁气动接触器vacuum contactor 真空接触器electromagnetic contactor 电磁接触器between open contacts 断口间continuous duty (service) 连续运行continuous rating 连续额定值control 控制automatic control 自动控制centralized control 集中控制local control 就地控制one-to-one control 一对一控制photoelectric control 光电控制器remote control 远方控制control circuit 控制回路electrical auxiliary control panel 电气辅助控制屏mosaic surface control panel 马赛克控制屏network control room 网控室cool 使冷却hydrogen inner cooled 氢内冷water cooled 水冷却natural cooling 自冷式forced air cooling system 强迫风冷系统copper bus-bar 铜母线core limb 铁芯柱corona 电晕corona-proof cover 防晕罩correcting circuit 校正电路correction factor 校正系数COS = change-over switch 切换开关CP = candle power 烛光creepage distance 爬距crest 峰，峰值crest voltage 峰值电压CS = control switch 控制开关CT = current transformer 电流互感器burden of CT CT的二次容量zero sequence CT 零序CTCU = coefficient of utilization 利用系数current电流capacitive current 电容电流dynamic stable current 动稳定电流field current 磁场电流impressed current 外加电流inductive current 电感电流interrupting current 开断电流leakage current 泄漏电流line-charging current 线路充电电流making current 关合电流momentary current 瞬时电流negative sequence current 负序电流no-load current 空载电流nominal discharge current 标称放电电流peak withstand current 峰值耐受电流rated breaking current 额定开断电流rated short time current 额定短时耐受电流reactive current 感性电流short circuit current 短路电流starting current 起动电流stray current 泄漏电流rated continuous current 额定持续电流zero sequence current 零序电流current amplification 电流放大current collector 集电器current converter 变流器current intensity 电流强度secondary current of CT CT的二次电流current shunt 分流器phase current 相电流DDC system 直流系统de-energized equipment 不带电设备definite time lag 定时限deformation 变形dehydrating breather 吸湿器delay 延时long time delay 长延时short time delay 短延时delta connection 三角形连接depth of embedded grounding wire 接地线埋深derating factor 降容系数diagram 图图纸CWD =control wiring diagram 控制接线图EWD =elementary wiring diagram 原理接线图mimic diagram 模拟图one-line diagram 单线图dial 拔号diameter 直径direct dialling 直拨directly burying 直埋敷设discharge 放电deep discharge 过放电intercept lightning discharge 截取雷电流self discharge 自放电discharge counter 放电计数器discharge final voltage 放电未期电压disconnection 解列busbar disconnection 母线解列system disconnection 系统解列system disconnection and field extinction解列灭磁dispatcher 调度员distortion factor 畸变系数diversity factor 分散系数document 文件double column 双柱DP = drip-proof 防滴型draw-out carriage 抽出式小车dust proof type 防尘型Eearthing 接地earthing rod 接地极earthing terminal 接地端子efficiency 效率electric 电气electric braking 电气制动electric welding machine 电焊机electrical life 电气寿命electricity engineering 电气工程electrode pole 电极electrolyte 电解液electromagnet 电磁铁3electromagnetic induction 电磁感应electromotance 电动势electronic element 电子元件emergency bell 事故铃energy 能，能量forced line energization 线路强送电successful forced line energization 线路强送电成功trial line energization 线路试送电enter the cubic from the top 柜顶进线enter the cubicle from the bottom 柜底进线excitation 励磁reducing excitation 减励磁force excitation 强励low excitation 低励磁over excitation 过励磁excitation cubicle 励磁柜excitation current 励磁电流force excitation factor 强励系数excitation initiating equipment 起励设备static excitation system 静态励磁系统excitation system response ratio 励磁系统响应比excitation transformer 励磁变压器excitation voltage 励磁电压exciter 励磁机main exciter 主励磁机pilot exciter 副励磁机standby exciter 备用励磁机expansion join 伸缩节expected life 期望寿命explosion-proof type 防爆型Ffailure alarming signal 事故报警信号fault 故障grounding fault 接地故障fault recollecting and recording device 事故追忆记录装置fault recorder 故障记录F-C = high-voltage current limiting fuse and vacuum contactor 高压限流熔断器及真空接触器feeder 馈线incoming feeder 进线outgoing feeder 出线feeder bay 馈线间隔field 磁场field extinction 灭磁field flashing equipment 起励设备field voltage 磁场电压fire 火fire proof blockage 防火堵料fire proof limit 耐火极限fire proof partition 耐火隔板fire protection pillows 阻火包fire retardant coating 阻燃涂料single face exit sign fixture 单面出口标志灯flexible joint 挠性接头FOA = forced oil air cooled 强油风冷foot candle ( F.C ) 英尺-烛光forced outage 强迫停机frequency 频率frequency converter station 变频站fuse 熔断器no powder-filled cartridge fuse 无填料封闭管式熔断器plug-in type fuse 插入式熔断器powder-filled cartridge fuse 有填料封闭管式熔断器screw-type fuse 螺旋式熔断器self-mending fuse 自复熔断器fast acting fuse 快速熔断器fuse blow 熔断器熔断Ggalvanic protection system 牺牲阳极保护系统galvanized steel 镀锌钢gap 间隙protective gap 保护间隙gapless metaloxide type 无间隙金属氧化型generator 发电机direct current generator 直流发电机dual inner water cooled generator 双水内冷发电机signal generator 信号发生器water-hydrogen-hydrogen coolinggenerator 水-氢-氢冷发电机generator hydrogen cooling system 发电机氢冷却系统generator load curve 发电机负荷曲线generator pedestal 发电机基座generator rotor 发电机转子generator sealing oil system 发电机密封油系统generator stator 发电机定子generator terminal 发电机端子generator terminal lead 发电机引出线generator termination room 发电机出线小室generator water cooling system 发电机水冷却系统generator-transformer extension unit 发变组扩大单元generator-transformer unit 发电机变压器组GIS = gas insulated switchgear 全封闭组合电器Glare 眩光glass cloth tape 波纤带grading ring 均压环、屏蔽环ground pad 接地端子groundbed 接地床anode groundbed 阳极接地床distributed-type groundbed 分散型接地床impressed current groundbed 泄漏电流接地床directly (solid) grounded 直接接地effectively grounded 有效接地un- grounded 不接地grounded through resistor 通过电阻接地grounding 接地single-phase grounding 单相接地grounding conductor 接地导体grounding megger 接地电阻测试仪main grounding network (grid) 主接地网grounding system 接地系统grounding terminal 接地端子grounding wire 接地线guarantee 保证Hharmonics 谐波4even harmonic 偶次谐波odd harmonic 奇次谐波heater 加热器self limiting parallel heater 自限制式并联加热器heating element 加热元件hertz (Hz) 赫兹high 高high pressure sodium ( HPS ) 高压钠灯high voltage transmission line 高压线路high-frequency amplification 高频放大high-frequency filter 高频滤波器hot-dipped galvanized 热镀锌Iidentification 识别igniter 触发器illuminance 照度impedance 阻抗asymmetrical impedance 不对称阻抗negative-sequence impedance 负序阻抗positive-sequence impedance 正序阻抗zero sequence impedance 零序阻抗impressed current cathodic protection 外加电流阴极保护indicator 指示器indoor type 户内式initial 首次initial power transmission 首次送电initial synchronization 首次并网input 输入instrumentation 测量仪表insulation 绝缘epoxy resin insulation 环氧树脂绝缘insulating strength 绝缘强度layer insulation 层间绝缘mica insulation 云母绝缘plastic insulation 塑料绝缘section insulation 段间绝缘turn insulation 匝绝缘insulation between phase 相间绝缘insulation class 绝缘等级insulation level 绝缘水平porcelain insulator 瓷质绝缘子post insulator 柱式绝缘子supporting insulator 支撑绝缘子suspending insulator 悬挂式绝缘子tension insulator 耐张绝缘子insulator 绝缘子interlock 联锁inverse time lag 反时限inverter 逆变器IPB = isolated phase bus duct 离相封闭母线Jtesting jack 试验端子Kkilovar (kVAR) 千乏kilovolt 千伏kilowatt (kW) 千瓦kilowatt-hour 千瓦时Llagging phase 滞后相lamp 灯left（right）arrow lamp 单面出口标志灯portable lamp 行灯mercury lamp 水银灯metal halide lamp 金属卤化物灯high intensity discharge lamp 高强气体放电灯fluorescent lamp 荧光灯incandescent lamp 白炽灯self-ballasted lamp 自镇流灯tungsten halogen lamp 碘钨灯projection lamp 投光灯lamp socket 灯座layer-to-layer 层间LDD = luminaire dirt depreciation 照明器污秽减光系数leading phase 超前相down- light 筒灯light source (illuminant) 光源flood lighting 泛光照明local lighting 局步照明emergency lighting 应急灯lighting box 照明箱emergency lighting box 事故照明箱double-faced plate lighting fixture 双块板灯flush mounted fluorescent lighting fixture嵌入式荧光灯tube fluorescent lighting fixture 简式荧光灯anticorrosive, dust-proof andwater-resistant lighting fixture 三防灯具wrap-around fluorescent lighting fixture全密封荧光灯garden lighting fixture 庭院灯waterproof fluorescent lighting fixture 防水荧光灯flameproof fluorescent lighting fixture 防爆耐火荧光灯road lighting fixture 路灯lighting fixture 灯具lightning 雷电tube type lightning arrester 管形避雷器valve type lightning arrester 阀型避雷器lightning arrester 避雷器lightning current 雷电流lightning protection 防雷lightning recorder 雷电记录器lightning rod 避雷针lightning strike 雷击lightning wave front shape 雷电波头形状lightning wire 避雷线live line connection 带电接线live line disconnection 带电拆线LLD = lamp lumen depreciation 光通量衰减系数Load 负荷target load 目标负荷load characteristic curve 负载特性曲线load rejection 甩负荷locked rotor current 转子堵转电流locked rotor torque 转子锁定转矩looping-off 解环loss 损耗copper loss 铜损iron loss 铁损load loss 负载损耗no-load loss 空载损耗supplementary load loss 附加损耗loss-ratio 损耗比5louver 格栅louver all ceiling 大面积发光天棚lug 接线片ring lug 环型接线片spade lug 铲型接线片terminal lug 接线端子lumen 流明background luminance 背景亮度luminaries 照明器effective luminous intensity 有效光强LX = lux 勒克司Mmagnetic lock 电磁锁maintenance 维护malfunction 误动作manhole 人孔marking strip 标识条MCB = miniature circuit breaker 微型断路器MCCB = moulded case circuit breaker 塑壳式断路器mechanical life 机械寿命megawatt (MW) 兆瓦metal clad 金属铠装meter 表计gravity meter 比重计insulation supervision meter 绝缘监察表kVAR-hour meter 无功电度表kW-hour meter 有功电度表phase meter 相位表plier-type current meter 钳型表power factor meter 功率因数表secondary meter 二次表计single-phase kilowatt-hour meter 单相电能表three-phase kilowatt-hour meter 三相电能表voltage meter 电压表watt-hour meter 电度表MF = maintenance factor 维护系数MHF = mounting height above the floor 距地面安装高度MHWP = mounting height above the work-place 距工作面安装高度milliammeter 毫安表millivoltmeter 毫伏表mimic bus 模拟母线mis-operation 误操作MOC = mechanism operated cell switch机构操作式开关motor 电动机adjustable speed motor 调速电动机commutator motor 整流子电动机governor motor 调速电动机horizontal type motor 卧式电动机induction motor 诱导电动机synchronous motor 同步电动机variable speed motor 可变速电动机vertical type motor 立式电动机motor maximum torque 电动机最大转矩mounted 镶嵌，安装standing pole mounted 立杆安装ceiling mounted 嵌入顶棚handrail mounted 扶手安装open mounted 明装wall mounted 吸壁flush mounted 暗装pendant mounted 悬挂stanchion mounted 柱上安装surface mounted 吸顶安装mounting type 安装方式movable type 移动式Nnameplate 铭牌negative pole 负极neutral point 中性点normal 正常NPB = non-segregated phase bus duct 共箱母线Oohm 欧姆OHM = ohmmeter 欧姆表oil level indicator 油位指示器OLTC = on-load tap-changer 有载分接开关open circuit characteristic curve 开路特牲曲线operate 操作operated in single phase 分相操作operated in three phase 三相操作operating duty cycle 操作顺序hydraulic operating mechanism 液压操作机构pneumatic operating mechanism 气动操作机构spring stored-energy operatingmechanism 弹簧贮能操作机构operating mechanism 操作机构operation 运行load limit operation 限负荷运行open phase operation 非全相运行trial operation 试运行pole slip operation 滑差运行operation mode 运行方式oscilloscope 示波器outdoor type 户外式outgoing feeder gantry structure 出线门型架构outgoing line 出线direction of outgoing line 出线方向output 输出shaft output 轴功率output increment 增负荷output reduction 降负荷overhead line 架空线over-flux 过激磁over-voltage times 过电压倍数oxygen index 氧指数PP.U. value = per unit value 标幺值packing instruction 包装说明paging dispatching unit 扩音调度机panel 盘control panel 控制盘side panel 边屏parallel 并联parallel branch 并联支路parameter 参数partial discharge 局部放电periodic duty service 定期运行phase 相in-phase 同相6phase angle 相角phase sequence 相序phase shifter 移相器phase to ground 相对地phase-angle difference 相角差plug-in unit 插件pole and tower 杆塔pole plate 极板pole-mounting type 柱上式positive pole 正极potential 电位,电势protective potential 保护电位step potential 跨步电压touch potential 接触电压transferred potential 传递电位zero potential 零电位potentio meter 电位计power 功率,能量active power 有功功率apparent power 视载功率electric power 电功率loss of power 失电reactive power 无功功率stand by power 备用电源power factor 功率因数line power flow 线路潮流power grid 电网auxiliary power ratio 厂用电率AC power source 交流电源DC power source 直流电源power system swing 系统振荡auxiliary power system 厂用电系统power system 电力系统printed wiring board 印刷电路板protection 保护back-up protection 后备保护branch overcurrent protection 分支过流保护busbar protection 母线保护cathodic protection 阴极保护differential protection 差动保护distance protection 距离保护freeze protection 防冻generator main protection 发电机主保护grounding protection 接地保护high-frequency protection 高频保护impedance protection 阻抗保护instantaneous overcurrent protection 速断保护longitudinal differential protection 纵差保护loss-of field protection 失磁保护low frequency protection 低频保护negative-sequence current protection 负序电流保护out-of step protection 失步保护over current protection 过流保护over excitation protection 过励磁保护reverse power protection 逆功率保护start-up protection 起动保护thermo-magnetic protection 热磁保护transverse differential protection 横差保护under voltage protection 低电压保护zero-sequence current protection 零序电流保护PT (=potential transformer) balanceprotection PT断线保护protection level at steep current 陡波冲击保护水平protective zone 保护范围PVC(polyvinyl chloride) insulated cable 聚氯乙烯绝缘电缆Qquality assurance 质量保证quality control 质量控制Rradio 无线电rated 额定rated input 额定输入rated output 额定输出rated value 额定值reactance 电抗capacitive reactance 容抗inductance reactance 感抗subtransient reactance 次暂态电抗synchronous reactance 同步电抗transient reactance 暂态电抗reactive power compensation device 无功补偿装置reactor 电抗器current-limiting reactor 限流电抗器disruptive reactor 分裂电抗器grounding reactor 接地电抗器shunt reactor 并联电抗器receiver 接收机receptacle (socket) 插座receptacle plug 插头re-close 重合闸recording 记录recording duration 记录时间recording instrument 记录仪表rectifier 整流器rectify 整流redial 重拨reflectance factor 反射系数reignite 重燃relative 有关的relay 继电器auxiliary relay 辅助（中间）继电器blocking relay 闭锁继电器Buchholtz relay 瓦斯/压力断电器closing relay 合闸继电器control relay 控制继电器current relay 电流继电器current-limiting relay 限流继电器delayed relay 延时继电器digital type protection relay 数字式继电保护directional relay 方向继电器distance relay 距离继电器flicker relay 闪光继电器lockout relay 出口继电器micro-processor based protective relay微机继电保护pilot relay 辅助继电器plugging relay 防逆转继电器position relay 位置继电器reclosing relay 重合闸继电器reed relay 舌簧继电器self-starting relay 自启动继电器SIC protection relay 半导体继电保护thermal relay 热继电器time relay 时间继电器tripping relay 跳闸继电器two zone distance relay 两段距离继电器7voltage relay 电压继电器voltage-controlled overcurrent relay 电压控制过电流继电器relay 继电器combined protection relay 综合保护继电器protection relay panel 继电保护屏relay protection 继电保护relay station 中继站relevant 相关的repeater 中继器repeater circuit 中继电路repeater group 中继组resistance 电阻high resistance 高阻low resistance 低阻arc suppression resistor 灭弧电阻dynamic braking resistor 制动电阻non-liner resistor 非线性电阻standard resistor 标准电阻starting resistor 起动电阻resistor 电阻器resolution 分辨率rheostat 变阻器slider-type rheostat 滑线式变阻器start rheostat 起动变阻器ripple contain factor 波纹系数RMS = root-mean-square 有效值rotor 转子squirrel-cage type rotor 鼠笼型转子wound type rotor 绕线式转子rotor conductor slot 转子线槽rotor retaining ring 转子护环rotor slip ring 转子滑环rotor winding 转子线圈rubber cushion 橡皮绝缘垫SS/MH = spacing-to-mounting height ratio 距高比sampling frequency 采样频率saturation 饱和saturation characteristics 饱和特性saturation factor 饱和系数scanner 扫描器scope 范围scope of supply 供货范围scope of work 工作范围seismic 地震self-holding 自保持sensitivity 灵敏度series 串联serial capacitor compensation device 串联电容补偿装置service level 服务级别setting range 整定范围setting value 整定值SF6 gas leakage detector SF6气体泄漏检测器SF6 gas moisture analyzer SF6气体湿度分析仪SF6 gas reclaiming equipment SF6气体回收设备shade and railing 遮栏sheath 护套inner sheath 内护套outer sheath 外护套shield 屏蔽short circuit 短路three-phase short circuit 三相短路two-phase short circuit 两相短路system short circuit capacity 系统短路容量short circuit characteristic curve 短路特牲曲线short circuit ratio 短路比short time parallel 短期并列signal 信号failure signal 事故信号flash signal 闪光信号status signal 状态信号signal indicator 信号指示器SIL = switching impulse level 操作冲击水平silicon-steel sheet 硅钢片single-phase 单相sinusoid 正弦波slight pressure device 微正压装置soil resistivity 土壤电阻率solid state rectifier 固态整流器solver plated 镀银spacer 间隔棒spare parts 备品备件special tool 专用工具splice 接头factory splice 工厂接头field splice 现场接头SS = select switch 选择开关stabilized power supply device 稳压电源装置starter 起动器full-voltage starter 全电压启动器reduced-voltage starter 降压启动器rotor resistance starter 转子电阻启动器star-delta starter 星-三角起动器magnetic starter 磁力起动器stator 定子stator core 定子铁芯stator end cover 定子端盖stator housing 定子外壳stator winding 定子线圈storage 贮存storage battery 蓄电池substation 变电站sub-synchronous resonance 低频共振surge 冲击浪涌surge absorber 过电压吸收装置zinc- oxide surge arrester 氧化锌避雷器surge arrester 避雷器magnetic blow surge arrester 磁吹避雷器SVC = static VAR compensator 静态无功补偿装置switch 开关disconnecting switch 隔离开关double earthing switch 双接地刀electronic switch 电子开关fuse- switch 熔断器式开关grounding (earthing) switch 接地开关iron clad switch 铁壳开关proximity switch 极近开关single earthing switch 单接地刀static transfer switch 静态转换开关voltmeter change-over switch 电压表切换开关switch 开关dimmer switch 调光开关knife switch 刀开关pull switch 拉线开关single pole switch 单极开关8switch off 断开switch on 合上switch-fuse 负荷开关switchgear 配电装置in-door switchgear 屋内配电装置out-door type switchgear 户外配电装置day-night switching unit 昼夜开关step-up switchyard 升压站switchyard 开关站symmetrical 对称的synchronization 同期single phase synchro-control 单相同期控制synchronization checking 同期鉴定automatic quasi-synchronization 自动准同期manual quasi-synchronization 手动准同期synchronizing device 同期装置synchronous condenser 调相器synchroscope 同期表system 系统system oscillation 系统振荡Ttap lead 抽头tap position indicator 分接头位置指示器tapping 分接tapping range 分接范围tapping step 分接级TEFC = totally enclosed with fan cooler 全封闭风冷型telecontrol 遥控telemetering 遥测telephon 电话telephon set 电话机automatic exchange telephone 自动交换机dispatching telephone 调度电话机extension telephone 电话分机noise-reducing telephone 抗噪音电话机talking on the telephone 通话video telephone 可视电话telephone booth 电话亭telephone handset 电话听筒teleregulation 遥调telesignalisation 遥信terminal 端子compression terminal 压缩端子compression type terminal 压接型端子terminal block 端子排terminal screw 端子螺钉test 试验AC withstand voltage test 交流耐压试验continuous breaking capability test 连续开断能力试验DC withstand voltage test 直流耐压试验evolving fault breaking test 开断发展性故障试验insulation withstanding test 绝缘耐受试验mechanical performance test 机械性能试验out-of-phase breaking test 失步开断试验parallel breaking test 并联开断试验partial discharge test 局部放电试验performance test 性能试验rain proof test 防雨试验routine test 例行试验routine test 常规试验sealing test 密封试验seismic test 抗震试验short circuit test 短路试验short circuit making and breaking test 短路关合和开断性能试验short-line fault test 近区故障试验site test 现场试验standard type test 标准型式试验static test 静态试验switching no-load long line test 分合空载长线试验switching no-load transformer test 分合空载变压器试验switching shunt reactor test 分合并联电抗器试验temperature rise test 温升试验test report 试验报告test voltage 试验电压pen tester 试电笔TEWAC = totally enclosed with watercooled air cooler 全封闭水空冷型thermo-couple 热电偶thermometer 温度计thyristor element 硅整流元件auto-reclosing dead time 自动重合闸无电流时间time 时间breaking time 分闸时间inherent closing time 固有合闸时间inherent opening time 固有分闸时间reclosing time 重合闸时间Max.breaking time 最大全分闸时间time delay de-engergizing 延时释放time delay energizing 延时带电time lead 导前时间tin galvanized 镀锡TOC = truck operated cell switch 小车操作式开关torque 转矩breakdown torque 破坏转矩starting torque 起动转矩torsional stress 扭应力transducer 变送器transformer 变压器auto- transformer 自耦变压器booster transformer 增压变压器busbar straight-through currenttransformer 母线式电流互感器bushing current transformer 套管式电流互感器core type transformer 芯式变压器coupling-capacitor voltage transformer耦合电容式电压互感器current transformer 电流互感器dry type transformer 干式变压器isolated transformer 隔离变压器lighting transformer 照明变压器low voltage auxiliary transformer 低压厂用变压器low voltage common transformer 低压公用变压器main transformer 主变压器maintenance transformer 检修变压器measuring transformer 测量用互感器oil-immersed type transformer 油浸变压器protecting transformer 保护用互感器PT = potential transformer 电压互感器shell type transformer 壳式变压器9。
机械类各行业专业英语词汇
机械类各行业专业英语词汇1. 汽车行业 (Automotive Industry)•Engine（发动机）•Transmission（传动装置）•Suspension（悬挂系统）•Brake（刹车系统）•Steering（转向系统）•Exhaust system（排气系统）•Fuel injection（燃油喷射系统）•Tire（轮胎）•Battery（电池）•Alternator（发电机）2. 航空航天工业 (Aerospace Industry)•rcraft（飞机）•Wing（机翼）•Fuselage（机身）•Cockpit（驾驶舱）•Landing gear（起落架）•Jet engine（喷气发动机）•leron（副翼）•Thrust（推力）•Propeller（螺旋桨）•Avionics（航空电子设备）3. 重工业 (Heavy Industry)•Machinery（机械）•Crane（起重机）•Bulldozer（推土机）•Excavator（挖掘机）•Boiler（锅炉）•Conveyor belt（输送带）•Generator（发电机）•Drill（钻机）•Foundry（铸造厂）•Welding（焊接）4. 电子行业 (Electronics Industry)•Circuit board（电路板）•Microchip（微芯片）•Transistor（晶体管）•Capacitor（电容器）•Resistor（电阻器）•Diode（二极管）•Integrated circuit（集成电路）•Semiconductor（半导体）•Printed circuit board (PCB)（印刷电路板）•Soldering（焊接）5. 工程机械 (Construction Machinery)•Cranes（起重机）•Excavators（挖掘机）•Bulldozers（推土机）•Loaders（装载机）•Rollers（压路机）•Pavers（铺路机）•Concrete mixer（混凝土搅拌机）•Tower crane（塔式起重机）•Trencher（挖沟机）•Forklift（叉车）6. 机床行业 (Machine Tool Industry)•Lathe（车床）•Milling machine（铣床）•Drilling machine（钻床）•Grinding machine（磨床）•Boring machine（镗床）•Shaping machine（拉坯机）•CNC machine tool（数控机床）•Power press（压力机）•Shearing machine（剪板机）•Woodworking machine（木工机械）7. 包装机械 (Packaging Machinery)•Filling machine（灌装机）•Sealing machine（封口机）•Labeling machine（贴标机）•Capping machine（旋盖机）•Wrapping machine（包装机）•Coding machine（打码机）•Shrinking machine（收缩机）•Vacuum packaging machine（真空包装机）•Cartoning machine（装箱机）•Palletizing machine（托盘包装机）8. 纺织机械 (Textile Machinery)•Spinning machine（纺纱机）•Weaving machine（织布机）•Knitting machine（针织机）•Dyeing machine（染色机）•Printing machine（印花机）•Stenter machine（拉伸机）•Embroidery machine（绣花机）•Textile finishing machine（纺织整理机）•Yarn twisting machine（纱线捻接机）•Textile testing equipment（纺织测试设备）9. 精密仪器 (Precision Instruments)•Optical microscope（光学显微镜）•Electronic balance（电子天平）•Spectrophotometer（分光光度计）•Ultrasonic cleaner（超声波清洗机）•Atomic force microscope (AFM)（原子力显微镜）•Mass spectrometer（质谱仪）•X-ray diffractometer（X射线衍射仪）•Scanning electron microscope (SEM)（扫描电子显微镜）•Electron beam lithography (EBL)（电子束曝光机）•Surface profilometer（表面粗糙度仪）10. 医疗器械 (Medical Devices)•MRI machine（核磁共振机）•CT scanner（计算机断层扫描仪）•X-ray machine（X射线机）•Ultrasound machine（超声波仪）•Surgical microscope（手术显微镜）•Electrocardiogram (ECG) machine（心电图机）•Defibrillator（除颤仪）•Anesthesia machine（麻醉机）•Blood pressure monitor（血压监测仪）•Thermometer（体温计）以上是机械类各行业中常见的专业英语词汇。
机械专业英语词汇，很全面带音标，搞电气的你懂多少机械？
机械专业英语词汇，很全面带音标，搞电气的你懂多少机械？金属切削 metal cutting [英] [ˈmetl][美] [ˈmɛtl]机床 machine tool [英] [məˈʃi:n tu:l][美] [məˈʃin tul]金属工艺学 technology of metals [tekˈnɔlədʒi] [ˈmetl]刀具cutter['kʌtɚ]摩擦 friction['frikʃən][’frɪkʃən]联结 link [liŋk]传动drive/transmission [trænzˈmiʃən]轴 shaft [ʃɑ:ft]弹性elasticity[ɪlæ'stɪsɪti:, ,i:læ-][ɪlæ'stɪsɪti, ,ilæ-]频率特性frequency characteristic ['fri:kwənsi][ˌkæriktəˈristik] 误差 error[ˈerə]响应 response[ri'spɔns]定位 allocation[ˌæləˈkeiʃən]机床夹具 jig[dʒɪg]动力学dynamic[dai'næmik]运动学kinematic[,kaini'mætik]静力学 static[ˈstætik]分析力学 analyse mechanics[ˈænəlaiz] .[mɪˈkænɪks]拉伸 pulling['puliŋ]压缩 hitting[hitiŋ]剪切 shear[ʃiə]扭转 twist[twist]弯曲应力 bending stress['bendiŋ] .[stres]强度 intensity[inˈtensiti]三相交流电 three-phase AC[feiz]磁路magnetic circles[mæɡˈnetik] .[ˈsə:kl]变压器transformer[trænsˈfɔ:mə]异步电动机 asynchronous motor[ei'siŋkrənəs] ['məutə]几何形状 geometrical[dʒɪəˈmetrɪkəl]精度 precision[priˈsiʒən]正弦形的 sinusoid[ˈsainəˌsɔid]交流电路AC circuit [ˈsə:kit]机械加工余量 machining allowance [mə'ʃi:niŋ] .[əˈlauəns]变形力 deforming force [dɪˈfɔ:miŋ] .[fɔ:s]变形 deformation [ˌdi:fɔ:ˈmeɪʃən, ˌdefə-]应力 stress [stres]硬度 rigidity [rɪˈdʒɪdɪti:]]热处理 heat treatment [ˈtri:tmənt]退火 anneal [əˈni:l]正火 normalizing ['nɔ:məlaiziŋ]脱碳 decarburization [di:,kɑ:bjuərai'zeiʃən]渗碳 carburization [,kɑ:bjurai'zeiʃən]电路 circuit [ˈsə:kit]半导体元件 semiconductor element [ˌsemikənˈdʌktə] .[ˈelimənt]反馈 feedback [ˈfi:dbæk]发生器 generator [ˈdʒenəreitə]直流电源 DC electrical source [i'lektrikəl] .[sɔ:s]门电路 gate circuit [ɡeit] [ˈsə:kit]逻辑代数 logic algebra [ˈlɔdʒik] .[ˈældʒibrə]外圆磨削 external grinding [eksˈtə:nl] ['ɡraindiŋ]内圆磨削 internal grinding [inˈtə:nəl] ['ɡraindiŋ]平面磨削 plane grinding [plein] ['ɡraindiŋ]变速箱 gearbox [ˈɡiəbɔks]离合器 clutch [klʌtʃ]绞孔 fraising [freiziŋ]绞刀 reamer D.J.[ˈri:mə]螺纹加工thread processing [θred] .[prəʊˈsesɪŋ]螺钉 screw [skru:]铣削 mill [mil]铣刀 milling cutter [ˈmiliŋ] .[ˈkʌtə]功率 power [ˈpauə]工件 workpiece [ˈwɜ:kpi:s]齿轮加工 gear machining [ɡiə] [mə'ʃi:niŋ]齿轮 gear [ɡiə]主运动 main movement [mein] .[ˈmu:vmənt]主运动方向 direction of main movement [diˈrekʃən]进给方向 direction of feed [diˈrekʃən] .[fi:d]进给运动 feed movement [fi:d] [ˈmu:vmənt]合成进给运动 resultant movement of feed [riˈzʌltənt] [ˈmu:vm ənt] [fi:d]合成切削运动resultant movement of cutting [riˈzʌltənt] [ˈmu:vmənt][ˈkʌtɪŋ]合成切削运动方向 direction of resultant movement of cutting [diˈrekʃən] [riˈzʌltənt] [ˈmu:vmənt] [ˈkʌtɪŋ]切削深度 cutting depth [ˈkʌtɪŋ] .[depθ]前刀面 rake face [reik][ feis]刀尖 nose of tool [nəuz] .[tu:l]前角 rake angle [reik] .[ˈæŋɡl]后角 clearance angle [ˈkliərəns] .[ˈæŋɡl]龙门刨削planing [plæniŋ]主轴 spindle [ˈspɪndl]主轴箱 headstock [ˈhedstɔk]卡盘 chuck [tʃʌk]加工中心 machining center [mə'ʃi:niŋ]车刀 lathe tool [leɪð] .[tu:l]车床 lathe [leɪð]钻削镗削 bore [bɔ:]车削 turning [ˈtɜ:nɪŋ]磨床 grinder [ˈgraɪndə]基准 benchmark [ˈbentʃˌmɑ:k]钳工 locksmith [ˈlɔkˌsmɪθ]锻 forge [fɔ:dʒ]压模 stamping [ˈstæmpiŋ]焊 weld [weld]拉床 broaching machine ['brəutʃiŋ] .[məˈʃi:n]拉孔 broaching['brəutʃiŋ]装配 assembling [ə'sembliŋ]铸造 found [faund]流体动力学fluid dynamics ['flu(:)id] [dai'næmiks]流体力学fluid mechanics ['flu(:)id] [mi'kæniks]加工 machining [mə'ʃi:niŋ]液压 hydraulic pressure [hai'drɔ:lik] ['preʃə]切线tangent ['tændʒənt]机电一体化 mechanotronics mechanical-electrical integration [,mekənə'trɔniks] [mi'kænikl] [i'lektrikəl] [,inti'ɡreiʃən] 气压air pressure pneumatic pressure [nju(:)'mætik]稳定性 stability [stə'biliti]介质 medium ['mi:djəm]液压驱动泵 fluid clutch ['flu(:)id] [klʌtʃ]液压泵 hydraulic pump [hai'drɔ:lik] [pʌmp]阀门valve [vælv]失效invalidation [in'vælideiʃn]强度 intensity [in'tensiti]载荷 load [ləud]应力 stress [stres]安全系数safety factor ['seifti] ['fæktə]可靠性 reliability [ri,laiə'biliti]螺纹thread [θred]螺旋 helix ['hi:liks]键 spline [splain]销 pin [pin]滚动轴承 rolling bearing ['rəuliŋ] ['bɛəriŋ]滑动轴承 sliding bearing ['slaidiŋ] ['bɛəriŋ]弹簧 spring [spriŋ]制动器 arrester brake [ə'restə] [breik]十字结联轴节 crosshead ['krɔshed]联轴器 coupling ['kʌpliŋ]链 chain [tʃein]皮带strap [stræp]精加工 finish machining ['finiʃ] [mə'ʃi:niŋ]粗加工 rough machining [rʌf] [mə'ʃi:niŋ]变速箱体 gearbox casing ['ɡiəbɔks] ['keisiŋ]腐蚀 rust [rʌst]氧化 oxidation [ɔksi'deiʃən]磨损 wear [wɛə]耐用度 durability [,djuərə'biliti]随机信号random signal ['rændəm] ['siɡnl]离散信号 discrete signal [dis'kri:t] ['siɡnl]超声传感器 ultrasonic sensor ['ʌltrə'sɔnik] ['sensə] 集成电路 integrate circuit ['intiɡreit] ['sə:kit]挡板 orifice plate ['ɔrifis] [pleit]残余应力 residual stress [ri'zidjuəl] [stres]套筒 sleeve [sli:v]扭力 torsion ['tɔ:ʃən]冷加工 cold machining [mə'ʃi:niŋ]电动机 electromotor [i,lektrəu'məutə]汽缸 cylinder ['silində]过盈配合 interference fit [,intə'fiərəns] [fit]热加工 hot work [hɔt] [wə:k]摄像头CCD camera ['kæmərə]倒角 rounding chamfer ['raundiŋ] ['tʃæmfə]优化设计 optimal design ['ɔptiməl] [di'zain]工业造型设计industrial moulding design [in'dʌstriəl] ['məuldiŋ] [di'zain]有限元 finite element ['fainait] ['elimənt]滚齿 hobbing ['hɔbiŋ]插齿 gear shaping [ɡiə] ['ʃeipiŋ]伺服电机actuating motor ['æktjueitiŋ] ['məutə]铣床 milling machine ['miliŋ] [mə'ʃi:n]钻床 drill machine [dril] [mə'ʃi:n]镗床 boring machine ['bɔ:riŋ] [mə'ʃi:n]步进电机 stepper motor ['stepə] ['məutə]丝杠 screw rod [skru:] [rɔd]导轨 lead rail [li:d] [reil]组件 subassembly ['sʌbə'sembli]可编程序逻辑控制器 Programmable Logic Controller PLC ['prəuɡræməbl] ['lɔdʒik] [kən'trəulə]电火花加工electric spark machining [i'lektrik] [spɑ:k] [mə'ʃi:niŋ] 电火花线切割加工 electrical discharge wire – cutting [i'lektrik əl] [dis'tʃɑ:dʒ]相图 phase diagram [feiz] ['daiəɡræm]固态相变 solid state phase changes [feiz]有色金属 nonferrous metal ['nɔn'ferəs] ['metl]陶瓷ceramics [si'ræmiks]合成纤维synthetic fibre [sin'θetic] ['fai bə]电化学腐蚀 electrochemical corrosion [i,lektrəu'kemikəl] [kə'r əuʒən]车架 automotive chassis [ɔ:tə'məutiv] ['ʃæsi]悬架 suspension [səs'penʃən]转向器 redirector ['ri:di'rektə]变速器 speed changer [spi:d] ['tʃeindʒə]板料冲压 sheet metal parts [ʃi:t] ['metl] [pɑ:ts]孔加工 spot facing machining [spɔt] ['feisiŋ] [mə'ʃ i:niŋ]车间 workshop ['wə:kʃɔp]工程技术人员 engineer [,endʒi'niə]气动夹紧 pneuma lock ['nju:mə] [lɔk]数学模型mathematical model [,mæθi'mætikəl]画法几何 descriptive geometry [dis'kriptiv] [dʒi'ɔmitri] 机械制图 Mechanical drawing [mi'kænikl] ['drɔ:iŋ]投影 projection [prə'dʒekʃən]视图 view [vju:]剖视图 profile chart ['prəufail] [tʃɑ:t]标准件standard component ['stændəd] [kəm'pəunənt] 零件图 part drawing [pɑ:t] ['drɔ:iŋ]装配图 assembly drawing [ə'sembli] ['drɔ:iŋ]尺寸标注 size marking [saiz] ['mɑ:kiŋ]技术要求 technical requirements刚度 rigidity [ri'dʒiditi]内力 internal force [in'tə:nl] [fɔ:s]位移 displacement [dis'pleismənt]截面 section ['sekʃən]疲劳极限 fatigue limit [fə'ti:ɡ] ['limit]断裂fracture ['fræktʃə]塑性变形plastic distortion ['plæstik, plɑ:stik] [dis'tɔ:ʃən] 脆性材料 brittleness material ['britl] [mə'tiəriəl]刚度准则 rigidity criterion [ri'dʒiditi] [krai'tiəriən]垫圈 washer ['wɔʃə]垫片 spacer ['speisə]直齿圆柱齿straight toothed spur gear [tu:ðd] [spə:]斜齿圆柱齿轮 helical-spur gear ['helikəl] [spə:][ɡiə]直齿锥齿轮 straight bevel gear [streit] ['bevəl] [ɡiə]运动简图kinematic sketch [,kaini'mætik] [sketʃ]齿轮齿条 pinion and rack ['pinjən] [ræk]蜗杆蜗轮 worm and worm gear [wə:m] [ɡiə]虚约束passive constraint ['pæsiv] [kən'streint]曲柄crank [kræŋk]摇杆racker ['rækə]凸轮cams [kæm]共轭曲线 conjugate curve ['kɔndʒuɡit] [kə:v]范成法 generation method [,dʒenə'reiʃən] ['meθəd]定义域 definitional domain [,defi'niʃən] [dəu'mein]值域 range [reindʒ]导数\\微分 differential coefficient [,difə'renʃəl] [kəui'fiʃənt]求导 derivation [deri'veiʃən]定积分 definite integral ['definit] ['intiɡrəl]不定积分 indefinite integral [in'definit] ['intiɡrəl]曲率 curvature ['kə:vətʃə]偏微分 partial differential ['pɑ:ʃəl] [,difə'renʃəl]毛坯 rough [rʌf]游标卡尺slide caliper [slaid] ['kælipə]千分尺 micrometer calipers [mai'krɔmitə] ['kælipəs]攻丝tap [tæp]二阶行列式 second order determinant ['sekənd] [' ɔ:də] [di't ə:minənt]逆矩阵 inverse matrix ['in'və:s] ['meitriks]线性方程组 linear equations ['liniə] [i'kweiʃən]概率 probability [,prɔbə'biliti]随机变量random variable ['rændəm] ['vɛəriəbl]排列组合 permutation and combination [,pə:mju(:)'teiʃən] [,k ɔmbi'neiʃən]气体状态方程 equation of state of gas [i'kweiʃən] [steit] [ɡæs]动能 kinetic energy [kai'netik] ['enədʒi]势能 potential energy [pə'tenʃəl] ['enədʒi]机械能守恒 conservation of mechanical energy [,kɔ nsə(:)'veiʃən] [m i'kænikl] ['enədʒi]动量 momentum [məu'mentəm]桁架 truss [trʌs]轴线axes ['æksi:z]余子式 cofactor [kəu'fæktə]逻辑电路 logic circuit ['lɔdʒik] ['sə:kit]触发器 flip-flop ['flipflɔp]脉冲波形 pulse shape [pʌls] [ʃeip]数模 digital analogy ['didʒitl] [ə'nælədʒi]液压传动机构fluid drive mechanism ['flu(:)id] [draiv] ['mekənizəm] 机械零件mechanical parts [mi'kænikl] [pɑ:t]淬火冷却 quench [kwentʃ]淬火 hardening ['hɑ:dəniŋ]回火 tempering ['tempəriŋ]调质 hardening and tempering ['hɑ:dəniŋ] ['tempəriŋ]磨粒 abrasive grain [ə'breisiv] [ɡrein]结合剂 bonding agent ['bɔndiŋ] ['eidʒənt]砂轮 grinding wheel ['ɡraindiŋ] [wi:l, hw-]机械零件mechanical parts [mi'kænikl] [pɑ:t]淬火冷却 quench [kwentʃ]淬火 hardening ['hɑ:dəniŋ]回火 tempering ['tempəriŋ]调质 hardening and tempering ['hɑ:dəniŋ] ['tempəriŋ]磨粒 abrasive grain [ə'breisiv] [ɡrein]结合剂 bonding agent ['bɔndiŋ] ['eidʒənt]砂轮 grinding wheel ['ɡraindiŋ] [wi:l, hw-]机床行业部分英汉对照按英文字母排序3-Jaws indexing spacers[dʒɔ:] ['indeksiŋ] ['speisə]三爪分割工具头A T C system ['sɪstəm]加工中心机刀库Aluminum continuous melting & holding furnaces [ə'lu:mən əm] [kən'tinjuəs] ['meltiŋ] ['həuldiŋ] ['fə:nis] 连续溶解保温炉Balancing equipment ['bælənsiŋ] [i'kwipmənt]平衡设备Bayonet ['beɪənɪt, -,net, ,beɪə'net]卡口Bearing fittings ['bɛəriŋ] ['fitiŋ]轴承配件Bearing processing equipment ['bɛəriŋ] [prəu'sesiŋ] [i'kwipm ənt]轴承加工机Bearings ['bɛəriŋ]轴承Belt drive [belt] [draɪv]带传动Bending machines ['bendiŋ] [mə'ʃi:n]弯曲机Blades [bleid]刀片Blades,saw [bleid] [sɔ:]锯片Bolts,screws&nuts [bəult][skru:][nʌts]螺栓,螺帽及螺丝Boring heads ['bɔ:riŋ] [hed]搪孔头Boring machines ['bɔ:riŋ] [mə'ʃi:n]镗床Cable making tools ['keibl] ['meikiŋ] [tu:l]造线机Casting,aluminium ['kæstɪŋ] [,ælju:'minjəm]铸铝Casting,copper ['kæstɪŋ] ['kɔpə]铸铜Casting,gray iron ['kæstɪŋ] [ɡrei] ['aiən]铸灰口铁Casting,malleable iron ['kæstɪŋ] ['mæliəbl]可锻铸铁Casting,other ['kæstɪŋ]其他铸造Casting,steel ['kæstɪŋ] [sti:l]铸钢Chain drive [tʃein] [draɪv]链传动Chain making tools [tʃein]造链机Chamfer machines ['tʃæmfə] [mə'ʃi:n]倒角机Chucks [tʃʌk]夹盘Clamping/holding systems ['klæmpiŋ]夹具/支持系统CNC bending presses （CNC=Computerized Numerical Control [kəm'pju:tə] [nju(:)'merikəl] [kən'trol]）['bendiŋ] [pres] 电脑数控弯折机CNC boring machines ['bɔ:riŋ] [mə'ʃi:n]电脑数控镗床CNC drilling machines ['driliŋ] [mə'ʃi:n]电脑数控钻床CNC EDM wire-cutting machines（EDM=Electron Discharge Machining [i'lektrɔn] [dis'tʃɑ:dʒ] [mə'ʃi:niŋ]放电加工）[mə'ʃi:n] ['waiə]电脑数控电火花线切削机CNC electric discharge machines [i'lektrik] [dis'tʃɑ:dʒ] [mə'ʃi:n]电脑数控电火花机CNC engraving machines [en'greɪvɪŋ] [mə'ʃi:n]电脑数控雕刻机CNC grinding machines ['ɡraindiŋ] [mə'ʃi:n]电脑数控磨床CNC lathes [leið]电脑数控车床CNC machine tool fittings [mə'ʃi:n] [tu:l] ['fitiŋ]电脑数控机床配件CNC milling machines ['miliŋ] [mə'ʃi:n]电脑数控铣床CNC shearing machines ['ʃiəriŋ] [mə'ʃi:n]电脑数控剪切机CNC toolings CNC ['tu:liŋ]刀杆CNC wire-cutting machines ['waiə] ['kʌtiŋ] [mə'ʃi:n] 电脑数控线切削机Conveying chains [kən'veiiŋ] [tʃein]输送链Coolers ['ku:lə]冷却机Coupling ['kʌpliŋ]联轴器Crimping tools [krimpiŋ] [tu:l]卷边工具Cutters ['kʌtə]刀具Cutting-off machines ['kʌtiŋ] [mə'ʃi:n]切断机Diamond cutters ['daiəmənd] ['kʌtə]钻石刀具Dicing saws ['daisiŋ] [sɔ:]晶圆切割机Die casting dies [dai] ['kɑ:stiŋ]压铸冲模Die casting machines [dai] ['kɑ:stiŋ] [mə'ʃi:n]压铸机Dies-progressive [dai] [prə'ɡresiv]连续冲模Disposable toolholder bits [dis'pəuzəbl] ['tu:l,həuldə] [bit]舍弃式刀头Drawing machines ['drɔ:iŋ] [mə'ʃi:n]拔丝机Drilling machines ['driliŋ] [mə'ʃi:n]钻床Drilling machines bench ['driliŋ] [mə'ʃi:n] [bentʃ]钻床工作台Drilling machines,high-speed ['driliŋ] [mə'ʃi:n] [hai] [spi:d]高速钻床 Drilling machines,multispindle [,m ʌlti] ['spindl]多轴钻床Drilling machines,radial ['driliŋ] [mə'ʃi:n] ['reidjəl]摇臂钻床Drilling machines,vertical ['driliŋ] [mə'ʃi:n] ['və:tikəl] 立式钻床drills [dril]钻头Electric discharge machines(EDM) [i'lektrik] [dis'tʃɑ:dʒ]电火花机Electric power tools [i'lektrik] ['pauə] [tu:l]电动刀具Engraving machines [en'greɪvɪŋ] [mə'ʃi:n]雕刻机Engraving machines,laser [en'greɪvɪŋ] [mə'ʃi:n] ['leizə]激光雕刻机 Etching machines ['etʃiŋ] [mə'ʃi:n]蚀刻机Finishing machines ['finiʃiŋ] [mə'ʃi:n]修整机Fixture ['fikstʃə]夹具Forging dies ['fɔ:dʒiŋ] [dai]锻模Forging,aluminium ['fɔ:dʒiŋ] [,ælju:'minjəm]锻铝Forging,cold ['fɔ:dʒiŋ] [kəuld]冷锻Forging,copper ['fɔ:dʒiŋ] ['kɔpə]铜锻Forging,other ['fɔ:dʒiŋ] ['ʌðə]其他锻造Forging,steel ['fɔ:dʒiŋ] [sti:l]钢锻Foundry equipment ['faundri] [i'kwipmənt]铸造设备5 Gear cutting machines [ɡiə] ['kʌtiŋ] [mə'ʃi:n]齿轮切削机Gears [ɡiə]齿轮Gravity casting machines ['ɡræviti] ['kɑ:stiŋ] [mə'ʃi:n]重力铸造机 Grinder bench ['ɡraində] [bentʃ]磨床工作台Grinders,thread ['ɡraində] [θred]螺纹磨床Grinders,tools & cutters ['ɡraində] [tu:l] ['kʌtə]工具磨床Grinders,ultrasonic ['ɡraində] ['ʌltrə'sɔnik]超声波打磨机Grinding machines ['ɡraindiŋ] [mə'ʃi:n]磨床Grinding machines,centerless ['ɡraindiŋ] [mə'ʃi:n] ['sentəles]无心磨床Grinding machines,cylindrical [si'lindrik(ə)l]外圆磨床Grinding machines,universal [,ju:ni'və:səl]万能磨床Grinding tools ['ɡraindiŋ] [tu:l]磨削工具Grinding wheels ['ɡraindiŋ] [wi:l, hw-]磨轮Hand tools [hænd] [tu:l]手工具Hard/soft and free expansion sheet making plant[iks'pænʃən] [ʃi:t]硬(软)板(片)材及自由发泡板机组Heat preserving furnaces [pri'zə:v] ['fə:nis]保温炉 Heating treatment funaces ['tri:tmənt] ['f ə:nis]熔热处理炉 Honing machines ['həuniŋ] [mə'ʃi:n]搪磨机Hydraulic components [hai'drɔ:lik][kəm'pəunənt]液压元件Hydraulic power tools [hai'drɔ:lik]液压工具Hydraulic power units [hai'drɔ:lik]液压动力元件Hydraulic rotary cylinders['rəutəri] ['silində]液压回转缸 Jigs [dʒiɡ]钻模Lapping machines ['læpiŋ] [mə'ʃi:n]精研机Lapping machines,centerless无心精研机Laser cutting ['leizə] ['kʌtiŋ]激光切割Laser cutting for SMT stencil['stensl, -sil]激光钢板切割机Lathe bench ['leizə] [bentʃ]车床工作台 Lathes,automatic ['leiz ə] [,ɔ:tə'mætik]自动车床Lathes,heavy-duty ['leizə] [hevi:'du:ti:, -'dju:-]重型车床Lathes,high-speed ['leizə] [hai] [spi:d]高速车床Lathes,turret ['leizə] ['tʌrit]六角车床Lathes,vertical ['leizə] ['və:tikəl]立式车床Lubricants ['lu:brikənt]润滑液Lubrication Systems [,lu:bri'keiʃən] ['sɪstəm]润滑系统Lubricators ['lju:brikeitə]注油机Machining centers,general [mə'ʃi:niŋ] ['sentə] ['dʒ enərəl]通用加工中心Machining centers,horizontal [mə'ʃi:niŋ] ['sentə] [,h ɔri'zɔntl]卧式加工中心Machining centers,horizontal & vertical [mə'ʃi:niŋ] ['sentə] [,h ɔri'zɔntl] ['və:tikəl]卧式及立式加工中心 Machining centers,vertical [mə'ʃi:niŋ] ['sentə] ['və:tikəl]立式加工中心Machining centers,vertical double-column type [mə'ʃi:niŋ] ['sentə] ['və:tikəl] ['dʌbl] ['kɔləm] [taip]立式双柱加工中心Magnetic tools [mæɡ'netik] [tu:l]磁性工具Manifolds ['mænifəuld]集合管Milling heads ['miliŋ] [hed]铣头Milling machines ['miliŋ] [mə'ʃi:n]铣床Milling machines,bed type ['miliŋ] [mə'ʃi:n] [taip]床身式铣床Milling machines,duplicating ['miliŋ] [mə'ʃi:n] ['dju:plikeitiŋ]仿形铣床Milling machines,horizontal ['miliŋ] [mə'ʃi:n] [,hɔri'z ɔntl]卧式铣床Milling machines,turret vertical ['miliŋ] [mə'ʃi:n] ['tʌrit] ['v ə:tikəl]六角立式铣床Milling machines,universal ['miliŋ] [mə'ʃi:n] [,ju:ni'və:səl]万能铣床 Milling machines,vertical ['miliŋ] [mə'ʃi:n] ['və:tikəl]立式铣床Milling machines,vertical & horizontal ['miliŋ] [mə'ʃ i:n] ['və:tikəl] [,hɔri'zɔntl]立式及卧式铣床Mold & die components [məuld] [dai] [kəm'pəunənt] 模具单元 Mold changing systems [məuld] ['tʃeindʒiŋ] ['sɪstəm] 换模系统Mold core [məuld] [kɔ:]模芯Mold heaters/chillers [məuld] ['hi:tə] ['tʃilə]模具加热器/冷却器 Mold polishing/texturing [məuld] ['pɔliʃiŋ] ['tekstʃə riŋ]模具打磨/磨纹Mold repair [məuld] [ri'pɛə]模具维修Molds [məuld]模具Nail making machines [neil] [mə'ʃi:n]造钉机Oil coolers [ɔil] ['ku:lə]油冷却器Overflow cutting machines for aluminium wheels ['əuvə'fləu] [mə'ʃi:n] [,ælju:'minjəm] [wi:l, hw-]铝轮冒口切断机P type PVC waterproof rolled sheet making plant 6 [taip] ['w ɔ:təpru:f] [rəuld] [ʃi:t] [plɑ:nt] PPVC高分子防水PCB fine piecing systems [fain] [pi:s] ['sɪstəm]( PCB =Printed -circuit Board [bɔ:d]印刷电路板)印刷电器板油压冲孔脱料系统 Pipe & tube making machines [paip] [mə'ʃi:n] ['tju:b] [mə'ʃi:n]管筒制造机Planing machines [plæniŋ] [mə'ʃi:n]刨床Planing machines vertical [plæniŋ] [mə'ʃi:n] ['və:tikəl]立式刨床Pneumatic hydraulic clamps [nju(:)'mætik] [hai'dr ɔ:lik] [klæmp]气油压虎钳Pneumatic power tools [nju(:)'mætik] ['pauə] [tu:l]气动工具Powder metallurgic forming machines ['paudə] [,metə'lə:dʒik] ['fɔ:miŋ] [mə'ʃi:n]粉末冶金成型机Presses,cold forging [pres] ['fɔ:dʒiŋ]冷锻冲压机presses,crank [pres] [kræŋk]曲柄压力机Presses,eccentric [pres] [ik'sentrik]离心压力机Presses,forging [pres] ['fɔ:dʒiŋ]锻压机Presses,hydraulic [pres]液压冲床Presses,knuckle joint [pres]肘杆式压力机Presses,pneumatic [pres] [hai'drɔ:lik]气动冲床Presses,servo [pres] ['sə:vəu]伺服冲床Presses,transfer [pres] [træns'fə:]自动压力机Pressing dies [presiŋ] ['daii:z]压模Punch formers [pʌntʃ] ['fɔ:mə]冲子研磨器Quick die change systems [kwik] [dai] [tʃeindʒ] ['sɪ stəm]速换模系统Quick mold change systems [kwik] [məuld] [tʃeindʒ] ['sɪstəm]快速换模系统Reverberatory furnaces [ri'və:bərətəri] ['fə:nis]反射炉Rollers ['rəulə]滚筒Rolling machines ['rəuliŋ] [mə'ʃi:n]辗压机Rotary tables ['rəutəri] ['teibl]转台Sawing machines ['sɔ:iŋ] [mə'ʃi:n]锯床Sawing machines,band ['sɔ:iŋ] [mə'ʃi:n] [bænd]带锯床Saws,band [sɔ:] [bænd]带锯Saws,hack [sɔ:] [hæk]弓锯Saws,horizontal band [sɔ:] [,hɔri'zɔntl] [bænd]卧式带锯Saws,vertical band [sɔ:] ['və:tikəl] [bænd]立式带锯 shafts [ʃɑ:ft]轴Shapers ['ʃeipə]牛头刨床Shearing machines ['ʃiəriŋ] [mə'ʃi:n]剪切机Sheet metal forming machines [ʃi:t] ['metl] ['fɔ:miŋ] [mə'ʃi:n]金属板成型机Sheet metal working machines [ʃi:t] ['metl] [mə'ʃi:n]金属板加工机Slotting machines ['slɔtiŋ] [mə'ʃi:n]插床spindles ['spindl]主轴Stamping parts ['stæmpiŋ] [pɑ:t]冲压机Straightening machines ['streitniŋ] [mə'ʃi:n]矫直机 Switches &buttons [switʃ] ['bʌtn]开关及按钮Tapping machines ['tæpiŋ] [mə'ʃi:n]攻螺丝机Transmitted chains [trænz'mit] [tʃein]传动链Tube bending machines ['tju:b] ['bendiŋ] [mə'ʃi:n]弯管机Vertical hydraulic broaching machine ['və:tikəl] [hai'drɔ:lik] ['brəutʃiŋ] [mə'ʃi:n]立式油压拉床Vises [vais]虎钳Vises,tool-maker [vais][ 'tu:l,meɪkə]精密平口钳Wheel dressers [wi:l, hw-] ['dresə]砂轮修整器 Woven-Cutting machines ['wəuvən]织麦激光切割机Wrenches [rentʃ]扳手螺丝词汇的中英文对照六角盖头螺帽 HEX CAP NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [kæp] [nʌts]六角锯齿螺帽 HEX SERRATED NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [se'reitid [nʌts] 六角轮缘螺帽HEX FLANGE NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [flændʒ] [nʌts] 高脚螺帽 HEX COUPLING NUTS(HIGH NUTS) (HEX= hexagon ['heksəɡən] 六角形; 六边形) ['kʌpliŋ] [nʌts] [hai]圆螺帽 ROUND NUTS [raund] [nʌts]四角螺帽SQUARE NUTS HEAVY HEX NUTS [skwɛə] [n ʌts] [ 'hevi] (HEX= hexagon ['heksəɡən] 六角形; 六边形)不锈钢六角螺帽STAINLESS STEEL HEX NUTS ['steinlis] [sti:l] (HEX= hexagon ['heksəɡən] 六角形; 六边形) [n ʌts]不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS ['steinlis] [sti:l] ['nailən] [in'sə:t] [lɔk] [nʌts] 普通六角螺帽HEX NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [nʌts] 六角重型螺帽 HEAVY HEX NUTS [ 'hevi]['heksəɡən][nʌts]薄型螺帽 HEX JAM NUTS ['heksəɡən][dʒæm] [nʌts]尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS ['nailən] [in'sə:t][lɔk] [nʌts]机械螺丝用六角螺帽 HEX MACHINE SCREW NUT ['heksəɡən] [mə'ʃi:n] 7 [skru:] [nʌt]机械工具英语机械工具spanner 扳子(美作:wrench) ['spænə] [rent ʃ] double-ended spanner ['spænə]双头扳子adjustable spanner, monkey wrench [ə'dʒʌstəbl] ['spænə] ['m ʌŋki] [rentʃ]活扳子,活络扳手box spanner 管钳子 (美作:socket wrench) [bɔks] ['spænə] ['sɔkit] [rentʃ]calipers ['kælipə]卡规pincers, tongs ['pinsəz] [tɔŋz]夹钳shears [ʃiəz]剪子hacksaw ['hæksɔ:]钢锯wire cutters ['waiə] ['kʌtə]剪线钳multipurpose pliers,universal pliers ['mʌlti'pə:pəs] ['plaiə] [,ju:ni'və:səl] ['plaiəz]万能手钳 adjustable pliers [ə'dʒʌstəbl] ['plaiəz]可调手钳punch [pʌntʃ]冲子drill [dril]钻chuck [tʃʌk]卡盘scraper ['skreipə]三角刮刀reamer ['ri:mə]扩孔钻calliper gauge ['kælipə] [ɡedʒ]孔径规rivet ['rivit]铆钉nut [nʌt]螺母locknut ['lɔknʌt]自锁螺母,防松螺母bolt [bəult]螺栓pin, peg, dowel [pin] [peɡ] ['dauəl]销钉washer ['wɔʃə]垫圈staple ['steipl]U形钉oil can 油壶jack工作服grease gun [ɡri:s]注油枪。
电气、机械等专业英语词汇大全(总结)
自动化专业词汇induction machine 感应式电机horseshoe magnet 马蹄形磁铁magnetic field 磁场eddy current 涡流right-hand rule 右手定则left-hand rule 左手定则slip 转差率induction motor 感应电动机rotating magnetic field 旋转磁场winding 绕组stator 定子rotor 转子induced current 感生电流time-phase 时间相位exciting voltage 励磁电压solt 槽lamination 叠片laminated core 叠片铁芯short-circuiting ring 短路环squirrel cage 鼠笼rotor core 转子铁芯cast-aluminum rotor 铸铝转子bronze 青铜horsepower 马力random-wound 散绕insulation 绝缘ac motor 交流环电动机end ring 端环alloy 合金coil winding 线圈绕组form-wound 模绕performance characteristic 工作特性frequency 频率revolutions per minute 转/分motoring 电动机驱动generating 发电per-unit value 标么值breakdown torque 极限转矩breakaway force 起步阻力overhauling 检修wind-driven generator 风动发电机revolutions per second 转/秒number of poles 极数speed-torque curve 转速力矩特性曲线plugging 反向制动synchronous speed 同步转速percentage 百分数locked-rotor torque 锁定转子转矩full-load torque 满载转矩prime mover 原动机inrush current 涌流magnetizing reacance 磁化电抗line-to-neutral 线与中性点间的staor winding 定子绕组leakage reactance 漏磁电抗no-load 空载full load 满载Polyphase 多相(的)iron-loss 铁损complex impedance 复数阻抗rotor resistance 转子电阻leakage flux 漏磁通locked-rotor 锁定转子chopper circuit 斩波电路separately excited 他励的compounded 复励dc motor 直流电动机de machine 直流电机speed regulation 速度调节shunt 并励series 串励armature circuit 电枢电路optical fiber 光纤interoffice 局间的waveguide 波导波导管bandwidth 带宽light emitting diode 发光二极管silica 硅石二氧化硅regeneration 再生, 后反馈放大coaxial 共轴的,同轴的high-performance 高性能的carrier 载波mature 成熟的Single Side Band(SSB) 单边带coupling capacitor 结合电容propagate 传导传播modulator 调制器demodulator 解调器line trap 限波器shunt 分路器Amplitude Modulation(AM)调幅Frequency Shift Keying(FSK)移频键控tuner 调谐器attenuate 衰减incident 入射的two-way configuration 二线制generator voltage 发电机电压dc generator 直流发电机polyphase rectifier 多相整流器boost 增压time constant 时间常数forward transfer function 正向传递函数error signal 误差信号regulator 调节器stabilizing transformer 稳定变压器time delay 延时direct axis transient time constant 直轴瞬变时间常数transient response 瞬态响应solid state 固体buck 补偿operational calculus 算符演算gain 增益pole 极点feedback signal 反馈信号dynamic response 动态响应voltage control system 电压控制系统mismatch 失配error detector 误差检测器excitation system 励磁系统field current 励磁电流transistor 晶体管high-gain 高增益boost-buck 升压去磁feedback system 反馈系统reactive power 无功功率feedback loop 反馈回路automatic Voltage regulator(AVR)自动电压调整器reference Voltage 基准电压magnetic amplifier 磁放大器amplidyne 微场扩流发电机self-exciting 自励的limiter 限幅器manual control 手动控制block diagram 方框图linear zone 线性区potential transformer 电压互感器stabilization network 稳定网络stabilizer 稳定器air-gap flux 气隙磁通saturation effect 饱和效应saturation curve 饱和曲线flux linkage 磁链per unit value 标么值shunt field 并励磁场magnetic circuit 磁路load-saturation curve 负载饱和曲线air-gap line 气隙磁化线polyphase rectifier 多相整流器circuit components 电路元件circuit parameters 电路参数electrical device 电气设备electric energy 电能primary cell 原生电池energy converter 电能转换器conductor 导体heating appliance 电热器direct-current 直流time invariant 时不变的self-inductor 自感mutual-inductor 互感the dielectric 电介质storage battery 蓄电池e.m.f = electromotive fore 电动势unidirectional current 单方向性电流circuit diagram 电路图load characteristic 负载特性terminal voltage 端电压external characteristic 外特性conductance 电导volt-ampere characteristics 伏安特性carbon-filament lamp 碳丝灯泡ideal source 理想电源internal resistance 内阻active (passive) circuit elements 有（无）源电路元件leakage current 漏电流circuit branch 支路P.D. = potential drop 电压降potential distribution 电位分布r.m.s values = root mean square values 均方根值effective values 有效值steady direct current 恒稳直流电sinusoidal time function 正弦时间函数complex number 复数Cartesian coordinates 笛卡儿坐标系modulus 模real part 实部imaginary part 虚部displacement current 位移电流trigonometric transformations 瞬时值epoch angle 初相角phase displacement 相位差signal amplifier 小信号放大器mid-frequency band 中频带bipolar junction transistor (BJT)双极性晶体管field effect transistor (FET)场效应管electrode 电极电焊条polarity 极性gain 增益isolation 隔离分离绝缘隔振emitter 发射管放射器发射极collector 集电极base 基极self-bias resistor 自偏置电阻triangular symbol 三角符号phase reversal 反相infinite voltage gain 无穷大电压增益feedback component 反馈元件differentiation 微分integration 积分下限impedance 阻抗fidelity 保真度summing circuit 总和线路反馈系统中的比较环节Oscillation 振荡inverse 倒数admittance 导纳transformer 变压器turns ratio 变比匝比ampere-turns 安匝(数)mutual flux 交互(主)磁通vector equation 向(相)量方程power frequency 工频capacitance effect 电容效应induction machine 感应电机shunt excited 并励series excited 串励separately excited 他励self excited 自励field winding 磁场绕组励磁绕组speed-torque characteristic 速度转矩特性dynamic-state operation 动态运行salient poles 凸极excited by 励磁field coils 励磁线圈air-gap flux distribution 气隙磁通分布direct axis 直轴armature coil 电枢线圈rotating commutator 旋转（整流子）换向器commutator-brush combination 换向器-电刷总线mechanical rectifier 机械式整流器armature m.m.f. wave 电枢磁势波Geometrical position 几何位置magnetic torque 电磁转矩spatial waveform 空间波形sinusoidal – density wave 正弦磁密度external armature circuit 电枢外电路instantaneous electric power 瞬时电功率instantaneous mechanical power 瞬时机械功率effects of saturation 饱和效应reluctance 磁阻power amplifier 功率放大器compound generator 复励发电机rheostat 变阻器self – excitation process 自励过程commutation condition 换向状况cumulatively compounded motor 积复励电动机operating condition 运行状态equivalent T – circuit T型等值电路rotor (stator) winding 转子（定子绕组）winding loss 绕组（铜）损耗prime motor 原动机active component 有功分量reactive component 无功分量electromagnetic torque 电磁转矩retarding torque 制动转矩inductive component 感性（无功）分量abscissa axis 横坐标induction generator 感应发电机synchronous generator 同步发电机automatic station 无人值守电站hydropower station 水电站process of self – excitation 自励过程auxiliary motor 辅助电动机technical specifications 技术条件voltage across the terminals 端电压steady – state condition 瞬态暂态reactive in respect to 相对….呈感性active in respect to 相对….呈阻性synchronous condenser 同步进相（调相）机coincide in phase with 与….同相synchronous reactance 同步电抗algebraic 代数的algorithmic 算法的1--master element主要元件，是指控制开关等元件。
常用电气自动化英语单词(带音标)
coil [kil] n.线圈 communication [k.mju:ni`kein] 通信、通 讯 compensation [kmpen`sein]补偿，矫正 component compress air [km`punnt] 元件 压缩空气 []
compress [km`pres] 压缩 compressor [km`pres] 压缩机 condensate condition conduct conductor configure congealer connect connector console constant contact 系 contact to earth 接地、触地、碰地 [:] contact [`kntækt] 触点 connection [kn`denseit] 冷凝、使凝结 [kn`din] 条件、状况、环境 [`kndkt] 传导 [.kndk`tiviti] 导电率 [kn`dkt] n.导体，导线 [kn`fig] 组态 [kn`di:l] 冷却器、冷冻器 [k`nekt] 连接 [k`nekn] 联接 [k`nkt] 联接器、接线盒 [kn`sul] 控制台 [`knstnt] 恒定的 [`kntækt] n.接触,触点,vt.接触,联
dynamometer 表
[.dain`mmit] 功率
[:]
control valve 调节阀 [vælv] controller conveyor cooler convert [kn`v:t]n.转换 vt.使转变， 转换…. cooktop [`kuktp] n.炉灶 [`ku:l] 冷却器 cooling fan 冷却风机 [fæn] cooling tower 冷却塔 [`tau] cooling water pump 冷却水泵 cooling [`ku:li] 冷却 core [k:] 铁心、核心、磁心 correction corrosion [k`rekn] 修正、改正 [k`run] 腐蚀
电子电气与机械工业常用的英文翻译
电子电气与机械工业常用的英文翻译电子电气与机械工业常用的英文翻译一．电气名词Electric items二．线路（母线、回路）Lines (Bus , circuits) 三．设备Equipments 四．保护、继电器Protection , relays 五．电气仪表Electric instruments 六．防雷Lightning protection 七．接地Grounding , earthing 八．室、所Room , Substation九．电修车间设备Equipments of electric repair 十．材料Material十一．图名Drawings , diagrams 十二．表头Tables十三．标准图词汇Terms from standard DWG电子电气与机械工业常用的英文翻译http:///tech/gongkong-power-electronics/40.html一．电气名词Electric items交（直）流Alternating (direct) current 短路电流Short-circuit current起始次暂态短路电流Initial subtransient short-circuit current 冲击电流Impulse current稳态短路电流Steady state short-circuit current 临界电流Critical current 切断电流Rupturing current 熔断电流Blow-out current 故障电流Fault current 计算电流Calculating current 极限有限电流Limit effective current 过电流Over current 逆电流Inverse current 整定电流Setting current 额定电流Rated current 电流密度Current density短路电流最大有效值Maximum effective value of short-circuit current 高压High-voltage , High-tension 低压Low-voltage , Low-tension 计算电压Calculating voltage 激磁电压Exciting voltage 冲击电压Impulse voltage 临界电压Critical voltage残留电压Residual voltage 击穿电压Puncture voltage 脉动电压Pulsating voltage 供电电压Supply voltage 电力电压Power voltage 照明电压Lighting voltage 灯丝电压Filament voltage 额定电压Rated voltage 电压损失Voltage loss过(欠)电压Over (under) voltage 线路电压Line voltage 电压降Voltage drop 工作电压Working voltage 一次电压Primary voltage 二次电压Secondary voltage电源Electric source (power supply) 自控电压Power supply for process control 6kV控制闪光电源Flashing supply for 6kV control 工作电源Working power supply (electric source) 保安电源Emergency power supply (electric source) 直流稳压电源Stabilized D.C. source 控制电源Control supply 直流电源D.C. source 交流电源 A.C. source 负荷计算Load calculation 设备容量Installed capacity 需要容量Electric demand 功率因数Power factor 安装高度Mounting height 耐电压Breakdown voltage工频耐压High-voltage test with working frequency 表面闪络Surface flash-over 直流泄漏 D.C. leakage 体电阻率Volume resistivity 介质损失角Dielectric loss angle 击穿强度Puncture intensity 电压等级Voltage grade 比重Specific gravity 性能Feature 相序Phase sequence 瞬时Instantaneous 倾角Angle of inclination 跨度Span正极Positive pole负极Negative pole截面(积) Cross section area 辅助电源Auxiliary source 遮断容量Interrupting capacity 载流量Current-carrying capacity 校正系数Correction factor 连续负荷Continuous load 长期载流量Continuous capacity 长时间额定值Longtime rating电动机堵转电流Locked-rotor motor current 限定负荷Limitedload 电感负荷Inductive load感应电流Induced current 本文来自技术世界电子电气与机械工业常用的英文翻译(2)二．线路（母线、回路）Lines (Bus , circuits)母线Bus-bar合闸电源母线Closing power source bus 闪光母线Flashing-bus 备用母线Spare bus装在支柱上的插接式母线Post-supported plug-in bus way 装在吊钩上的插接式母线Hook-supported plug-in bus way 装在支架上的插接式母线Bracket-supported plug-in bus way 小母线Miniature bus电源小母线Power supply miniature bus 操作小母线Operating miniature bus事故信号小母线Miniature bus for fault signal 闪光小母线Flashing miniature bus 主母线Main bus直流主母线 D.C. main bus 预告母线Prewarning bus 干线Main line照明干线Lighting main line 接地干线Grounding main line 插座干线Receptacle main line 电压干线Voltage main line 端子出线Terminal outgoing 中性线Neutral 支线Branch-line 引入线Lead-in电气线路Electric circuit交流配电线路 A.C. distribution circuit 直流配电线路 D.C. distribution circuit 事故照明线路Emergency lighting circuit 控制线路Control circuit接地或接零线路Grounding or neutralizing circuit 信号线路Signal circuit有接地极的接地线路网Grounding with grounding electrodes定子绕组测温回路Temperature measuring circuit for stator winding 接地信号回路Grounding signal circuit 闪光信号回路Flashing-signal circuit 开阀回路Circuit for opening valve 关（闭）阀回路Circuit for closing valve 开度计回路Circuit for opening meter 电流测量回路Current-measuring circuit 差动保护回路Differental protective circuit 过流保护回路Over-current protective circuit 合闸回路Closing circuit停车延时回路Delayed shutdown circuit 掉闸回路Trip circuit 激磁回路Exciting circuit 备用回路Spare circuit 主回路Main circuit 馈路Feeder circuit 现有回路Existing circuit 单线回路Single-wire circuit 接地回路Earthed circuit 有电压的电路Live circuit 三．设备Equipments高压开关柜H.V. switchgear动力配电箱Power distribution cabinet 电源配电箱Source distribution cabinet直流配电屏D.C. switchboard (distribution panel) 交流低压配电屏 A.C.L.V. switchboard (distribution panel) 静电电容器柜Static capacitor cabinet多种电源插销箱Receptacle box for miscellaneous power supplies 控制箱Control cabinet照明配电箱Lighting (distribution panel) 连接箱Junction box 出线盒Outlet box 开关箱Switch box控制台Console分段屏Sectionalizing panel 进线屏Incoming line panel 电控箱Electric control panel 边屏Side board 端子箱Terminal box 供电盘Power supply box 瓶车箱Synchronizing cabinet感应调压器专用变压器高压柜Special transformer H.V. cabinet for induction voltage regulator 电压互感器柜Potential transformer cabinet 信号屏Signal panel 浮充屏Floating panel 蓄电池屏Battery panel 充电屏Charging panel母线联络柜Bus tie cabinet 转换开关Transfer switch电压表转换开关Voltmeter change-over switch 铁壳开关Metal-clad switch (Iron-clad switch) 管式熔断器Cartridge fuse 真空断路器Vacuum circuit breaker (V.C.B.) 自动开关Automatic switch高压负荷开关H.V. load break switch 三极高压断路器3-pole HV circuit-breaker 刀开关Knife switch 转换开关Transfer switch 双极铁壳开关2-pole iron-clad switch 风扇变速开关Fan speed regulator switch 密闭照明灯开关Hermetic lighting switch 防爆照明灯开关Explosion-proof lighting switch 行程开关Limit switch 高压隔离开关H.V. disconnecting switch明装单极板钮开关Surface-mounted single-pole toggle switch 暗装单极板钮开关Flush-mounted single-pole toggle switch 三路开关Three-way switch气密式组合开关Hermetic packet type switch 防护式开关Guard type switch 联锁开关Interlock switch操作方式选择开关Selecting switch for types of operation控制电源开关Switch for control supply 主令开关Master switch (controller)多切点切换开关Multi-point change-over switch 按钮Push-button。
建筑机电安装工程等中英词汇
建筑机电安装工程等中英词汇建筑机电安装工程是指在建筑工程中，涉及到机械、电气、水暖和空调等方面的安装施工。
此类工程涉及到大量的专业术语和技术知识，下面将介绍一些常用的中英词汇。
一、机械安装1. 圆形法兰／Circular flange2. 方形法兰／Square flange3. 接头／Joint4. 法兰／Flange5. 螺纹／Thread6. 按钮电器／Pushbutton element7. 风机／Fan8. 风道／Duct9. 管道／Pipe10. 阀门／Valve11. 风机箱／Fan chamber12. 轴承／Bearing13. 传动带／V-belt14. 减速器／Speed reducer15. 齿轮／Gear二、电气安装1. 配电箱／Distribution box2. 断路器／Circuit breaker3.开关／Switch4. 插座／Socket5. 电缆／Cable6. 电线／Wire7.照明设备／Lighting equipment8. 安全开关／Safety switch9. 电子计量系统／Electronic weighing system10. 电气控制／Electrical control11. 接线盒／Junction box12. 导线槽／Wireslot13. 变压器／Transformer14. 安全地线／Ground wire15. 电磁阀／Solenoid valve三、水暖安装1. 水龙头／Faucet2. 水表／Water meter3. 水泵／Water pump4. 管道／Pipeline5. 接头／Joint6. 水箱／Water tank7. 排水管道／Drainage pipeline8. 排水设备／Drainage equipment9. 水管／Water pipe10. 厕所／Toilet11. 洗脸盆／Washbasin12. 节流器／Throttle13. 水阀／Water valve14. 防爆泵／Explosion-proof pump15. 管道密封／Pipeline sealing四、空调安装1. 冷凝器／Condenser2. 蒸发器／Evaporator3. 空调机组／Air conditioning unit4. 风机盘管／Fan coil unit5. 冷凝水泵／Condensate water pump6. 风口／Air outlet7. 风道／Duct8. 风机／Fan9. 水泵／Water pump10. 水箱／Water tank11. 送风机／Supply fan12. 回风机／Return fan13. 空气处理机组／Air handling unit14. 空气过滤器／Air filter15. 清洁器／Cleaner以上为建筑机电安装工程的部分相关中英词汇，掌握这些词汇是建筑机电安装工程专业人员必备的基本技能。
电气专业英语词汇表
1. Personnel 人员职员2. V oltmeter 电压表伏特计3. Ohmmeter 欧姆计电阻表4. Megohmmeter 兆欧表5. Wattmeter 瓦特计电表功率6. Watt-hour 瓦时瓦特小时7. Ammeter 安培计电流表8. calibrate 校正9. scale 刻度量程10. rated 额定的11. interfere with 有害于。
12. indicating needle仪表指针13. hazardous 危险的14. pivot 支点15. terminal 端子16. spiral 螺旋形的17. spring 弹簧18. shunt 分流，分路，并联，旁路19. rectifier 整流器20. electrodynamometer 电测力计21. strive for 争取22. vane 机器的叶，叶片23. strip 条，带，（跨接）片24. crude 不精细的，粗略的25. polarity 极性26. fuse 保险丝，熔丝27. rugged 坚固的28. depict 描绘，描写29. cartridge 盒式保险丝30. blow （保险丝）烧断31. plug fuse 插头式保险丝32. malfunction 故障33. deenergize 不给…通电34. insulation 绝缘35. generator 发电机36. magneto 磁发电机37. humidity 湿度38. moisture 潮湿湿气39. abbreviate 缩写，缩写为40. transformer 变压器41. thumb 检查，查阅42. milliammeter 毫安表43. multimeter 万用表44. dynamometer 测力计，功率计45. aluminum 铝46. deteriorate 使….恶化47. eddy current 涡流48. gear 齿轮，传动装置49. dial 刻度盘50. semiconductor 半导体51. squirrel 鼠笼式52. diode 二极管53. thyristor 晶闸管54. transistor 电子晶体管55. triac 双向可控硅56. phase 相位（控制）57. silicon 硅58. crystal 晶体59. wafer 薄片60. anode 阳极，正极61. cathode 阴极62. collector 集电极]63. emitter 发射极64. schematic （电路）原理图符号65. leakage 漏电流66. rating 额定值，标称值，定额67. dissipate 散发68. breakdown 击穿69. heat sink 散热器70. self-latching 自锁71. commutation 换向72. geometry 几何结构73. squeeze 压榨，挤，挤榨74. light-dimmer 调光75. capability 容量76. studmounted 拴接式77. hockey puck 冰球78. fin 飞边79. active 有源的80. horsepower 马力81. diameter 直径82. in. （inch ,inches）英寸83. extruded 型材的84. clamp 夹住，夹紧85. compound 紧密结合86. wrench 扳手87. torque 转矩，扭矩88. enclosure 外（机）壳89. ventilation 通风，流通空气90. sealed-off 封的91. thermal 热的，热量的92. substantially 主要地，实质上地93. aptly 适当地，适宜地94. demystify 阐明95. allude 暗指，直接提到96. cease 停止，终了97. line 线电压98. ripple 脉动.99. redundant 多余的100. separately 单独励磁地101. synchronous 同步电动机102. circuitry 电路，线路103. cost-effective 花费大的104. capacitor 电容器105. dictate 确定106. trade-off 权衡，折衷107. criteria 标准，判据108. analog electronics电力电子学109. saturate 使…饱和110. active region 动态区域111. due 应得到的112. ratio 比，比率113. signify 表示114. encode 编码115. resonance 共鸣116. radiated 传播117. molecule 分子118. diaphragm 震动膜119. acoustic wave 声波120. wavy groove 起伏的沟槽121. deflection 挠度，挠曲122. strain gage 应变计量器123. tachometer 转速计124. thermocouple 热电偶125. oscilloscope 示波器126. analytical 解析的127. numerical 数值的128. integrate 求…的积分129. scale 改变比例130. frequency- domain 频域131. random 随机的132. audio 音频的133. operation amplifier 运算放大器134. summation 求和，加法135. sophisticated 复杂的，完善的136. mass-produce 大量生产137. subtract 减去138. inverting amplifier 反向放大器139. uninverting amplifier 同相放大器140. derive 推倒141. active filter 有源滤波器142. stabilize 使稳定143. moderate 适度的，适中的144. virtue 优点145. amplification 扩大146. capacitor 电容器147. impedance 阻抗148. bode plot 波特图149. simulate 模拟，方针150. narrowband filter 带通滤波器151. low-pass filter低通滤波器152. high-pass filter高通滤波器153. differential equation 微分方程154. prebias 预偏置155. summer 加法器156. weighted 加权的157. refinement 改进158. accommodate 适应159. envision 预见160. alphabet 字母表161. validity 正确性162. proposition 命题163. binary 二进制164. nevertheless 然而165. reveal 展现166. complement 补码167. truthtable 真值表168. algebraical 代数的169. trial and error 试错法，试凑法170. elapse 时间（流逝）171. enumerate 列举172. expire 期满,终止173. brute 僵化的174. prime 上撇号175. trigger 引起,触发176. inversion 反相,反转177. quadruple 四合一178. fabricate 制造179. integrated circuit 集成电路180. capsule 封装181. compatible 兼容的182. obsolete 废弃的183. threshold 门限,阈值184. zener diode 齐纳二极管185. adjacent 临近的,接近的186. arc welding 电弧焊187. intimately 密切地188. recast 重做189. bistable circuit 双稳电路190. cutoff 截止,关闭191. symmetry 对称192. lable 为……标号193. equilibria 平衡194. lever 杆,杠杆195. latch circuit 锁存电路196. depress 压下197. flip-flop 触发器198. glitch 同步199. leading edge 上升沿200. lagging(trailing) edge 下降沿201. inhibit 禁止202. hitherto 迄今,至今203. toggle (来回)切换204. impulse 推动力205. air gap 气隙206. aircraft 飞机207. alternating current, AC 交流208. armature 电枢209. automobile 汽车210. bearing 轴承211. brush 电刷212. carbon 碳213. circumference 圆周214. clearance 间隙215. coils 线圈绕组216. commutator 换向器217. connection 接线端218. copper bar 铜导条219. copper end rings 铜端环220. core 铁心221. cylindrical 圆柱式的222. doubly excited 双边励磁223. electromechanical 机电的224. felt 毡225. ferromagnetic 铁磁的226. field pole 磁极227. flux density 磁通密度228. frame 机座，机壳229. generator 发电机230. glue 胶合，粘贴231. graphite 石墨232. induction motor感应电动机233. laminate 叠制，叠压234. lubricant 润滑剂，润滑油235. magnetic flux 磁通236. magnetizing current 磁化电流，励磁电流237. mechanical rectifier 机械式换向器238. metallic 金属的239. penetrate 透过，渗透240. periphery 周围，圆周241. perpendicular 垂直的，正交的242. polarity 极性243. protrude 使伸出，突出244. reluctance 磁阻245. revolving magnetic field 旋转磁场246. rotor 转子247. salient 突出的248. salient-pole 凸极式249. servo 伺服250. singly excited 单边励磁251. slip rings 滑环252. slot 槽，开槽253. squirrel-cage 鼠笼式，笼型254. stator 定子255. synchronous machine 同步电机256. torque 转矩257. toroid 环状物258. transformer 变压器259. unidirectional 单方向的，方向不变的260. winding 绕组261. wound-rotor 绕线式262. wrap 捆，缠，环绕263. yoke 轭264. allowable temperature rise 允许温升265. alnico 铝镍钴合金266. asynchronous machine 异步电机267. automobile starter motor 汽车启动机268. backlash 啮合间隙，齿隙269. centrifugal force 离心力270. ceramic 陶瓷的271. compound-wound 复励272. constraint 强制，约束273. counter emf 反电势274. counterpart 对应物275. culminate 达到极值点276. cumulative compound 积复励277. demagnetization退磁，去磁278. denominator 分母279. differential compound 差复励280. dissipate 浪费281. equilibrium level 平均值282. equivalent circuit 等效电路283. figure of merit品质因数，优值284. flicker 闪烁，摇曳285. flux per pole 每极磁通286. friction 摩擦287. in parallel with 并联288. in series with 串联289. in terms of 根据，在……方面290. in the vicinity of 在…附近，在…左右291. indispensable 必需的，必不可少的292. inherent 固有的293. insulation 绝缘294. long-shunt 长复励295. loss 损耗296. magnetization curve 磁化曲线297. merit 优点，长处，指标298. no load 空载299. nonetheless，none the less 仍然，依然300. numerator 分子301. overload 过载302. permissible 允许的303. permanent-magnet永磁304. pertinent 有关的305. power flow diagram 功率流程图306. prefix 前缀，把…放在前面307. rated torque 额定转矩308. reaction 电感309. rheostat 变阻器，电阻箱310. series-wound 串励311. shunt-wound 并励312. short-shunt 短复励313. starting current 启动电流314. starting torque 启动转矩315. synchronous speed 同步转速316. theorem 定理317. turns 匝数318. undervoltage 欠电压319. Ward-Leonard system 发电机-电动机组系统320. windage 通风321. yield 产生，提供322. adjacent 相邻的，邻近的323. autotransformer自耦变压器324. braking 制动325. cam 凸轮326. chamber 室，腔327. conveyor 传送机328. corrosion 腐蚀329. counterclockwise 逆时针330. counter electromotive force ，CEMF反电势331. dashpot relay 油壶式继电器332. diaphragm 膜片，挡板333. drill 钻床334. elapse 过去，消逝335. enclosure 机壳336. expel 排出，放出337. fasten 固定，连接338. furnace 炉339. fuse 熔断器，保险丝340. general-purpose relay通用继电器341. hydraulic 液压传动342. initiate 引起，促进343. intake 吸入344. knob 旋钮，圆形把手345. latching relay 自锁继电器346. lathe 车床347. limit switch 限位开关348. moisture 潮气，湿度349. mount 安装350. octal-base 八脚的351. orifice 孔，注孔352. pedal 踏板，踏蹬353. phase sequence 相序354. piston 活塞355. pivot 轴，支点，旋转中心356. plunger 可动铁心，插棒式铁心357. pneumatic 气动的358. relay 继电器359. single-phase 单相的360. solenoids 螺线管361. solid-state relay 固态继电器362. spring 弹簧363. tap 抽头364. three-phase 三相365. timing relay 延时继电器366. toggle 搬扭，刀闸367. vibration 振动368. absolute encoder 绝对编码器369. accelerometer 加速度测量仪370. actuator 执行机构371. analog-to-digital conversion, ADC 模数转换器372. angular 角的373. auxiliary 辅助的374. as a rule of thumb 根据经验375. bellows 膜盒376. binary-coded decimal,BCD二进制码377. calibration 校准，标定，刻度378. cantilever 悬臂379. closed-loop 闭环380. induction machine 感应式电机381. horseshoe magnet 马蹄形磁铁382. magnetic field 磁场383. eddy current 涡流384. right-hand rule 右手定则385. left-hand rule 左手定则386. slip 转差率387. induction motor 感应电动机388. rotating magnetic field 旋转磁场389. winding 绕组390. stator 定子391. rotor 转子392. induced current 感生电流393. time-phase 时间相位394. exciting voltage 励磁电压395. solt 槽396. lamination 叠片397. laminated core 叠片铁芯398. short-circuiting ring 短路环399. squirrel cage 鼠笼400. rotor core 转子铁芯401. cast-aluminum rotor铸铝转子402. bronze 青铜403. horsepower 马力404. random-wound 散绕405. insulation 绝缘406. ac motor 交流环电动机407. end ring 端环408. alloy 合金409. coil winding 线圈绕组410. form-wound 模绕411. performance characteristic 工作特性412. frequency 频率413. revolutions per minute 转/分414. motoring 电动机驱动415. generating 发电416. per-unit value 标么值417. breakdown torque 极限转矩418. breakaway force 起步阻力419. overhauling 检修420. wind-driven generator 风动发电机421. revolutions per second 转/秒422. number of poles 极数423. speed-torque curve 转速力矩特性曲线424. plugging 反向制动425. synchronous speed 同步转速426. percentage 百分数427. locked-rotor torque 锁定转子转矩428. full-load torque 满载转矩429. prime mover 原动机430. inrush current 涌流431. magnetizing reacance 磁化电抗432. line-to-neutral 线与中性点间的433. staor winding 定子绕组434. leakage reactance 漏磁电抗435. no-load 空载436. full load 满载437. Polyphase 多相(的)438. iron-loss 铁损439. complex impedance 复数阻抗440. rotor resistance 转子电阻441. leakage flux 漏磁通442. locked-rotor 锁定转子443. chopper circuit 斩波电路444. separately excited 他励的445. compounded 复励446. dc motor 直流电动机447. de machine 直流电机448. speed regulation 速度调节449. shunt 并励450. series 串励451. armature circuit 电枢电路452. optical fiber 光纤453. interoffice 局间的454. waveguide 波导波导管455. bandwidth 带宽456. light emitting diode 发光二极管457. silica 硅石二氧化硅458. regeneration 再生, 后反馈放大459. coaxial 共轴的,同轴的460. high-performance 高性能的461. carrier 载波462. mature 成熟的463. Single Side Band(SSB) 单边带464. coupling capacitor 结合电容465. propagate 传导传播466. modulator 调制器467. demodulator 解调器468. line trap 限波器469. shunt 分路器470. Amplitude Modulation(AM调幅471. Frequency Shift Keying(FSK)移频键控472. tuner 调谐器473. attenuate 衰减474. incident 入射的475. two-way configuration 二线制476. generator voltage 发电机电压477. dc generator 直流发电机478. polyphase rectifier 多相整流器479. boost 增压480. time constant 时间常数481. forward transfer function 正向传递函数482. error signal 误差信号483. regulator 调节器484. stabilizing transformer稳定变压器485. time delay 延时486. direct axis transient time constant 直轴瞬变时间常数487. time invariant 时不变的488. transient response 瞬态响应489. solid state 固体490. buck 补偿491. operational calculus 算符演算492. gain 增益493. pole 极点494. feedback signal 反馈信号495. dynamic response 动态响应496. voltage control system 电压控制系统497. mismatch 失配498. error detector 误差检测器499. excitation system 励磁系统500. field current 励磁电流501. transistor 晶体管502. high-gain 高增益503. boost-buck 升压去磁504. feedback system 反馈系统505. reactive power 无功功率506. feedback loop 反馈回路507. automatic Voltage regulator(A VR)自动电压调整器508. third harmonic voltage 三次谐波电压509. reference V oltage 基准电压510. magnetic amplifier 磁放大器511. amplidyne 微场扩流发电机512. self-exciting 自励的513. limiter 限幅器514. manual control 手动控制515. block diagram 方框图516. linear zone 线性区517. potential transformer 电压互感器518. stabilization network 稳定网络519. stabilizer 稳定器520. air-gap flux 气隙磁通521. saturation effect 饱和效应522. saturation curve 饱和曲线523. flux linkage 磁链524. per unit value 标么值525. shunt field 并励磁场526. magnetic circuit 磁路527. load-saturation curve 负载饱和曲线528. air-gap line 气隙磁化线529. polyphase rectifier 多相整流器530. circuit components 电路元件531. circuit parameters 电路参数532. electrical device 电气设备533. electric energy 电能534. primary cell 原生电池535. energy converter 电能转换器536. conductor 导体537. heating appliance 电热器538. direct-current 直流539. self-inductor 自感540. mutual-inductor 互感541. the dielectric 电介质542. storage battery 蓄电池543. e.m.f = electromotive fore电动势544. unidirectional current 单方向性电流545. circuit diagram 电路图546. load characteristic 负载特性547. terminal voltage 端电压548. external characteristic外特性549. conductance 电导550. volt-ampere characteristics伏安特性551. carbon-filament lamp 碳丝灯泡552. ideal source 理想电源553. internal resistance 内阻554. active (passive) circuit elements有（无）源电路元件555. deviation 偏差556. leakage current 漏电流557. circuit branch 支路558. P.D. = potential drop 电压降559. potential distribution 电位分布560. r.m.s values = root mean square values均方根值561. permanent magnet 永磁体562. effective values 有效值563. steady direct current 恒稳直流电564. sinusoidal time function 正弦时间函数565. complex number 复数566. Cartesian coordinates 笛卡儿坐标系567. modulus 模568. real part 实部569. imaginary part 虚部570. displacement current 位移电流571. trigonometric transformations 瞬时值572. epoch angle 初相角573. phase displacement 相位差574. signal amplifier 小信号放大器575. mid-frequency band 中频带576. bipolar junction transistor(BJT双极性晶体管577. field effect transistor(FET)场效应管578. electrode 电极电焊条579. polarity 极性580. gain 增益581. isolation 隔离分离绝缘隔振582. emitter 发射管放射器发射极583. collector 集电极584. base 基极585. self-bias resistor 自偏置电阻586. triangular symbol 三角符号587. phase reversal 反相588. infinite voltage gain 无穷大电压增益589. feedback component 反馈元件590. differentiation 微分591. integration 积分下限592. impedance 阻抗593. fidelity 保真度594. summing circuit 总和线路反馈系统中的比较环节595. pneumatic 气动的596. Oscillation 振荡597. inverse 倒数598. admittance 导纳599. transformer 变压器600. turns ratio 变比匝比601. ampere-turns 安匝(数)602. mutual flux 交互(主)磁通603. vector equation 向(相)量方程604. power frequency 工频605. capacitance effect 电容效应606. induction machine 感应电机607. shunt excited 并励608. series excited 串励609. separately excited 他励610. self excited 自励611. field winding 磁场绕组励磁绕组612. speed-torque characteristic 速度转矩特性613. dynamic-state operation动态运行614. salient poles 凸极615. excited by 励磁616. field coils 励磁线圈617. air-gap flux distribution 气隙磁通分布618. direct axis 直轴619. armature coil 电枢线圈620. rotating commutator 旋转（整流子）换向器621. commutator-brush combination换向器-电刷总线622. mechanical rectifier 机械式整流器623. armature m.m.f. wave 电枢磁势波624. Geometrical position 几何位置625. magnetic torque 电磁转矩626. spatial waveform 空间波形627. sinusoidal–density wave正弦磁密度628. external armature circuit 电枢外电路629. instantaneous electric power瞬时电功率630. instantaneous mechanical power 瞬时机械功率631. effects of saturation 饱和效应632. reluctance 磁阻633. power amplifier 功率放大器634. compound generator 复励发电机635. rheostat 变阻器636. self –excitation process 自励过程637. commutation condition 换向状况638. cumulatively compounded motor 积复励电动机639. operating condition 运行状态640. equivalent T –circuit T型等值电路641. rotor (stator) winding 转子（定子绕组）642. winding loss 绕组（铜）损耗643. prime motor 原动机644. active component 有功分量645. reactive component 无功分量646. electromagnetic torque 电磁转矩647. retarding torque 制动转矩648. inductive component 感性（无功）分量649. abscissa axis 横坐标650. induction generator 感应发电机651. synchronous generator 同步发电机652. automatic station 无人值守电站653. hydropower station 水电站654. process of self –excitation 自励过程655. auxiliary motor 辅助电动机656. technical specifications 技术条件657. voltage across the terminals 端电压658. steady –state condition瞬态暂态659. reactive in respect to 相对….呈感性660. active in respect to 相对….呈阻性661. synchronous condenser 同步进相（调相）机662. coincide in phase with 与….同相663. synchronous reactance 同步电抗664. algebraic 代数的665. algorithmic 算法的666. biphase 双相的667. bilateral circuit 双向电路668. bimotored 双马达的669. corridor 通路670. shunt displacement current 旁路位移电流671. leakage 泄漏672. lightning shielding 避雷673. harmonic 谐波的674. insulator string 绝缘子串675. neutral 中性的676. zero sequence current 零序电流677. sinusoidal 正弦的678. square 平方679. corona 电晕,放电680. bypass 旁路681. voltmeter 电压表682. ammeter 电流表683. micrometer 千分尺684. thermometer 温度计685. watt-hour meter 电度表686. wattmeter 电力表687. private line 专用线路688. diameter 直径689. centimeter 厘米690. restriking 电弧再触发691. magnitude 振幅692. oscillation 振荡693. auxiliary 辅助的694. protective gap 保护性间隙放电695. receptacle 插座696. lightning arrester 避雷装置697. bushing 套管698. trigger 起动装置699. stress 应力700. deterioration 损坏,磨损701. spark gap 火花放电隙702. traveling-wave 行波703. wye-connected 星形连接704. enclosure 设备外壳705. live conductor 带电导体706. fuse 熔断器707. structural 结构上的708. out-of-step 不同步的709. resynchronize 再同步710. synchroscops 同步指示器711. automatic oscillograph 自动示波器712. nominally 标称713. sampling 采样714. potential transformer 电压互感器715. fraction 分数716. switchyard 户外配电装置717. hazard 危险718. bushing 高压套719. contact 触点720. energize 励磁721. trip coil 跳闸线圈722. over-current relay 过电流继电器723. armature 衔铁724. pickup current 始动电流725. release current 释放电流726. solenoid relay 螺管式继电器727. induction-disc relay 感应圆盘式继电器728. inverse time relay 反时限继电器729. hydraulic 液力的730. dashpot 阻尼器733. electrical stressing 电气应力734. mechanical stressing 机械应力■735. crystal 晶体的，水晶，晶体736. demodulation 解调737. derivative 导数738. diaphragm 膜片739. differentiation 微分740. discrete 离散的741. displacement 位移742. eddy 涡流743. encoder 编码器744. error 误差，偏差745. expedite 加速746. feedback 反馈747. feedforward 前馈748. forging 锻造749. hysteresis 磁滞750. immunity 抗扰性751. impedance 阻抗752. increment encoder 增量编码器753. inertia 惯性754. integration 积分755. interface 接口756. jerk 振动，冲击757. kinematic 运动的，运动学的758. longitudinal 经度了；纵向的759. manipulations 操作，控制，处理760. manipulator 机械手，操作器761. measurand 被测量，被测量对象762. modulation 调制763. multiplexer 多路转换器764. offset 偏心765. open-loop 开环766. orthogonal 垂直的，正交的767. perpendicular 垂直的，正交的768. photosensor 光电传感器769. piezoelectric 压电的770. plant 装置，设备771. potentiometer 电位器772. predominant 主要的，突出的773. prismatic 棱型的774. proximity 距离775. quantization 量化776. radial 径向的777. redundant 多余的，重复的778. representation 代表，表示779. resolver 解算器780. resonance 共振781. revolute 旋转的，转动的782. rig 设备783. robustness 鲁棒性784. rolling 轧制785. sampling period 采样周期786. signal-to-noise ration ，SNR信噪比787. strategy 策略788. subsequently 其后789. tachometer 测速仪790. terminology 术语，专门名词791. threshold 门，界限，阈值792. trajectory 轨迹793. transducer 传感器794. transient 瞬态的795. transistor-to-transistor logic，TTL 晶体管-晶体管逻辑796. transit 运输797. translatory 平移的798. algorithm 算法799. ambiguity 模棱两可800. antenna 天线801. arbitration 仲裁，公断802. autonomous 匿名的803. capacity 容量804. chao 混乱805. checksum 检查和806. circumnavigate 饶过807. client-server 客户-服务器808. client-server model 客户服务器模型809. corridor 通道，走廊810. decouple 解耦，去除干扰811. depict 描述812. distributed system 分布式系统813. dungen 地牢814. electronic mail 电子邮件815. entity 实体816. etiquette 规则817. exponential 指数818. fallout 余波，附带结果819. forward 转发820. full-duplex 全双工821. gamut 全体，整体822. goggles 护目镜，潜水镜823. half-duplex 半双工824. hierarchy 阶梯，等级825. host 主机826. infrastructure 基础，底层结构827. interactive 交互式828. interface data unit 接口数据单元829. inventory 存货，清单830. killer 迷人的831. newsgroup 新闻组832. object-oriented 面向对象的833. outgoing 外出了，离开的834. pointer 指针835. primitive 操作，原型836. process 进程837. propagation 传播，宣传838. protocol 协议839. protocol data unit 协议数据单元840. remote database 远程数据库841. remote login 远程登陆842. remote terminal 终端843. reprisal 报复844. router 路由器845. service data unit 服务数据单元846. simultaneous 同时的847. static allocation 静态分配848. subnet 子网849. taxonomy 分类学，分类850. telemedicine 远程医疗851. terminology 术语852. testbed 测试平台853. therapy 治疗854. token 令牌855. topology 拓扑学856. videoconference 可视会议857. virtual reality 虚拟现实858. worldwide shared 全球共享的859. wide area network 广域网860. actuator 执行器861. bar code reader 条码阅读器862. by-product 副产品863. call for 需要864. contiguous 邻近的865. culprit 犯罪者866. elusive 难以捉摸的867. filter 滤波器868. fluctuation 升降剥动，不规则的变化869. hardwired 硬接线的870. havoc 大破坏871. high-volume 大容量872. induction coupling 感应耦合873. inference 干扰874. injection molding 注模875. instruction set 指令集876. interconnection 相互连接877. isolation transformer 隔离变压器878. maintenance 维护879. multiple axis drive 多轴驱动880. pilot light 信号灯881. RF noise 射频干扰882. shock 冲击883. solenoid 线圈884. stand-alone 独立的885. stepper 步进电机886. thermocouple 热电偶887. troubleshoot 排除故障888. uninterruptible power supply 不间断电源889. vendor 生产厂商890. vibration 震动891. water-tight 防水892. wreak 发泄，报复893. configuration 组态894. Cyclic Redundancy Check 循环冗余检查895. electromagnetic interference 电磁干扰896. meticulous 详细的897. nonvolatile 非挥发的898. parity 校验899. peripheral 外设900. pharmaceutical 药剂，药品901. rack mounting 机架安装902. resident program 驻留程序903. spare 备用的904. standby 后备的905. volatile 挥发的，易失的906. watchdog timer 看门狗定时器907. distribution 分配，配电908. primary 最初的，基本的，初级线圈909. radial 径向的，辐射状的910. premise 上述各点，前言，根据911. residential 住宅的，居住的912. residence 住宅913. occupancy 占有，占用，居住914. tap 抽头915. establishment 组织，部门916. dwelling 住房917. panel 操纵台，面板918. laundry 洗衣房919. means 手段，工具920. condominium （国际）共官921. branch circuit 直路922. conduit 导线，导线管923. rigid 刚性的，坚固的924. clamp 夹，钳925. bolt 螺栓926. cubicle 立方体927. interrupter 断续(流、电、路)器928. margin 余量，裕度929. nuisance 障碍，公害930. receptacle 插座，插孔931. algebraic 代数的932. virtually 实际上，实质上933. fluorescent 荧光的，有荧光性的934. fixture 设备，装置]935. vicinity 附近，邻近，接近936. ballast 镇流器937. feeder 馈电线，电源线，馈电板938. ground-fault protector （GFP）939. ground-fault circuit interrupter（GFCI）接地故障保护器，接地故障断路器940. centrifugal 离心的，离心力941. whilst=while942. sphere 球体943. counteract 抵抗，抵消，消除944. joint 关节，铰链945. keyway 键槽946. pivot 轴，支点947. link 连杆948. throttle 节流阀，风门949. synthesis 综合物950. mass 物质，块，堆951. classic 古典的，经典的，传统的952. steer 驾驶，操纵，引导953. servomechanism 伺服机构，伺服系统954. actuate 激励，驱动955. intimately 紧密地，直接的956. academic 纯理论的957. dial 刻度盘，调节控制盘958. calibration 标定，标准化959. lubrication 润滑，注油960. arrangement 结构961. wear 磨损，损耗962. subtle 微妙的，巧妙的963. transducer 变送器964. hand-wheel 手轮，驾驶盘，操纵盘965. hydraulic 液压的，液压传动装置966. pneumatic 气动的，气动力学的967. electro-hydraulic 电动液压的968. electro-pneumatic 电动气动的969. coincidence 一致，相等970. faithful 正确的，可靠的971. fidelity 重现精度，真实，正确972. oscillatory 振动的，摆动的973. align 调整，校准974. profile 轮廓，仿行975. milling machine 铣床976. gyroscope 陀螺仪977. launcher 发生器，启动装置978. inertial 惯性的，惯量的979. electrolytic 电解的980. plate （电）镀981. distillation 蒸馏982. blend 混合，调和，配料983. philosophy 基本原理984. analytical 分析的，分解的985. orifice 侧流板，隔板986. diaphragm 膜，隔板987. knob 钮，圆形把手988. nomenclature 术语989. liable 有责任的990. autonomic 自治的991. grossly 大概，大体上的992. ideological 思想的993. morally 道德上，道义上994. boredom 讨厌，无趣995. deterioration 变化，降低品质996. ambient 环境的997. remarks 附注，要点998. differential pressure transducer差压变送器999. viscous 粘稠的1000.viscous friction 粘滞摩擦.1001.bearing 轴承1002.rolling mill 轧钢机1003.mine minder 矿坑卷扬机1004.velodyne 伺服积分器1005.feasible 可行的1006.regenerative braking 回馈制动1007.eddy current braking 涡流制动1008.dynamic braking 能耗制动1009.reverse braking 反接制动1010.advent 出现1011.prolong 延长1012.armature 电枢1013.contactor 接触器1014.hoist 起重机1015.field winding 励磁绕组mutator 换向器1017.riiple 纹动1018.creep 蠕动1019.tachogenerator 测速发电机1020.quadrant 象限1021.coast 跟踪惯性1022.profile 轮廓1023.conveyance 运输工具1024.lever 手柄，控制杆1025.forced commutation 强迫换流1026.ac squirrel cage induction motor 交流笼型感应电动机1027.accutrol 控制器1028.stator 定子1029.rotor 转子1030.DC link 直流环节1031.Triac 双向晶闸管1032.Adjustable-voltage inverter 电压型逆变器1033.Current source inverter 电流型逆变器1034.refinement 明确表达1035.pros and cons 优缺点1036.cogging 齿槽效应.1037.retrofit 改型1038.damper 减速器1039.pitfall 缺陷1040.vernier 游标尺1041.jog 啮合1042.runout table 输出轨道1043.clinker-cooler 熟料冷却器1044.kiln 炉1045.grinder 磨床1046.pitch 齿轮1047.inventory 存货1048.cone pulley 塔轮，快慢轮1049.escalation 升级，提高1050.forced-draft 强制通风1051.induced-draft fan 吸风机1052.elbow 弯。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
英语
automatic regulator
amplifier
armature control
rheostatic
armature voltage control
battery charger
battery
buzzer
bushing
bell connection diagram characteristic computer checking
connection
frequency
motor list
Interlocked flow sheet block diagram
Flow sheet
motor type
rating KW
automatic panel
control
汉语 自动调节器 增幅器 电枢变阻控制 电枢电压控制 充电器 电池 蜂鸣器 衬套、套管 铃 接线图 特性 计算机 检查 压固端子 计数器 凸轮控制器 限流继电器 限流电抗器 电缆线头 电缆接线箱 变换器 电容器 模数转换器
反馈信号
feed back signal
绝缘子
isolator, insulator
分配器
distributor
控制器
controller
汉语
英语
名板
name plate
备件备品配件 spare parts
电气设备
electric equipment
速度
speed
转速 电机容量 盖板
revolution r.p.m motor capacity cover
控制箱
control box
自动/断电/手动 auto/off/manual
变阻式起动器 rheostat starter
起动/停止
start/stop
室内照明
indoor lighting
温度开关
temperature switch
室外照明
outdoor lighting
计时器
timer
变压器 变换器 transformer
英语
magnetic contactor
push button
safety rope
power source
overload
rotor
stator
ball bearing unit
slide base
casing
handle
safety guard
flexible tube
control motor
liquid level gauge
油位表
oil level gauge
水位表
water level gauge
流量计
flow meter
速度表
velocity meter
测速表、转数表 tachometer
（料、液）位开
关
level switch
标定、校准
calibration
至中央控制盘 to central panel
微开关
micro switch
行程开关 限位
开关
limit switch
闸刀开关
knife switch
现场控制盘
local control panel水银开关ຫໍສະໝຸດ mercury switch
控制板
control board
压力开关
pressure switch
控制台
control desk
按钮（开关） push button
法兰盘
flange
轴
shaft
电磁阀
solenoid valve
压力开关
pressure switch
限位（行程）开
关
limit switch
温度开关
temperature switch
浮动开关
float switch
导管
conduit
联轴节
coupling
防松螺母、对关
螺母
lock nut
电缆管
cable duct
汉语
英语
端子、终端
terminal
端子盒
terminal box
温度计 压力表 流量表
thermometer manometer, pressure gauge flow meter
压力
pressure
排风
draft
（料、液）液面
指示器
level indicator
真空表
vacuum gauge
液位表
零件清单
parts list
电机座
motor base
电机盖
motor cover
磁断线圈
magnetic brake coil
插塞式保险丝 plug fuse
汉语 电磁触点 按钮 安全绳 电源 过载、超载 转子 定子 滚珠轴承 滑动座 外壳，罩 把手 安全罩 伸缩管挠性管 控制电机 连接 频率 电机清单 连锁流程图 方框图 流程图 电机型号 额定功率 自动控制盘
英语 control power lamp power source lamp fuse annunciator lamp test lamp reset alarm fault indicator pilot lamp local control Central control local panel central panel counter KW-hour meter ampere meter volt meter watt meter resistance condenser thyristor bus bar
现场控制室
local control room
电机起动器
motor starter
电气室
electric room
辅助继电器
auxiliary relay
受电盘
incoming panel
开关
switch
配电盘 控制盘 遥控盘
switchboard control panel remote control panel
自动返回
self return
转换器
converter
连锁
interlock
增幅器
amplifier
电源
power source
变送器
transmitter
电压
voltage
调节计
regulator
电流
current
汉语 控制电源 电灯电源 电灯 熔丝、保险丝 信号装置 灯光检查 灯光重设 报警 故障显示器 指示灯 现场控制 中央控制 现场控制盘 中央控制盘 计数器 电度表 电流表 电压表 功率表 电阻 电容器 可控硅整流器 硅整流器 母线
汉语
英语
i 电气类
汉语
英语
电
electricity
指示计
indicator
电力
electric power
接触器，触点 contactor
输出
output
断电器，遮断器 breaker
配电站
substation
继电器
relay
遥控室
remote control room
转换开关
change-over switch