机械类专业词汇中英文对照翻译表大全
机械专业相关词汇中英文翻译大全
机械专业相关词汇中英文翻译大全单价unit price工日合计Man-day total/work-day total人工费cost of labor材料费materials expenses机械的mechanical检查接线connection test发电机generator调相机phase regulator周波cycle减负荷装置 load-shedding equipment断路器柜circuit breaker cabinet单母线single busbar互感器transformer每相电流Current by Phase封闭式插接close type socket joint发电机控制面板generator control panel分级卸载sorted unloading同步控制synchronization control调速器 speed governor信号屏signal screen继电器relay高压柜high pressure cabinet油浸电力变压器oil-immersed power transformer空气断路器air circuit breaker控制屏control panel直流馈电屏direct current feed control panel电容器electric condenser计量盘metering panel成套配电箱whole set of distribution box落地式floor model控制开关Control switches铜芯电力电缆Copper core power cable控制电缆actuating cable热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing万用槽钢versatile U-steel电缆托架 cable bracket钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座防爆插座Explosion-proof socket接地绞线earthing twisted pair接地母线 earthing bus接地极 lightning conductor硬质聚氯乙烯管rigid polyvinyl chloride pipe航空集散站air terminal水银灯具Mercury Lamp金属卤化物灯metal halide lamp高压钠灯High Pressure Sodium Lamp额定电压Rated Voltage额定功率Rated Power光源 Light Source防护等级Grade of Protection高压汞灯High Pressure Mercury Lamp高压钠灯High Pressure Sodium Lamp金属卤化物灯Metallic Halide Lamp照明电缆 lighting cable单线mongline穿线threading接地跨接线 earthing jumper分线箱junction box接线盒connection box圆钢round steel扁钢flat steel插座socket配电盘switchboard转换开关alternation switch自动指令呼叫装置automatic instruction calling device 扬声器loudspeaker明装Unfold Install暗装Conceal Install感温探测器Thermal Detector转台造型机turntable molding machine气动震实造型机air jarring moulding machine有箱造型机box molding machine压铸机die casting machine热室压铸机hot-chamber die casting machine 惯性落砂机inertia knock-out grid浇包ladle浇注机cating machine冲天炉cupola (cupola furnace)水冷冲天炉water cooled cupola焦碳炉coke-fired furnace退火炉annealing oven回火炉drawing furnace喷丸机high pressure blasting machine抛砂机sand throwing machine摆轮式混砂机speedmuller自动分箱机automatic box splitter自动合箱机automatic closer自动壳型机autoclino风动工具air tool锻造forging无型锻造open forging水压机锻造hydraulic forging机器锻造machine forging自由锻造flat-die forging多型槽锻造multiple impression forging冷锻cold forging锤锻（自由锻）hammer forging平锻horzontal forging镦锻upset forging辊锻roll forging模锻die forging热模锻pressure forging开式模锻open-die forging精密模锻prescision drop forging挤压模锻no-draft forging冷拉cold draw热拉hot draw冷挤压cold extruding切边trim冷切边cold trim热切边hot trim冲孔punching校正straightening板料冲压sheet stamping制坯blank锻造毛坯forging blank上模upper die下模bottom die(counter die)上锤头top swage下锤头lower die汽锤steam hammer无砧坐模锻锤forging hammer without anvilbed摩擦锤jump hammer落锤block hammer水平分模（平锻机）horizontal parting冷锻模cold forging die型锻模forging die精整模forming die顶锻模joggling die锻压机forging die水压机water press平锻机horizontal forging machine汽力锻压机steam power forging press 压弯机bending press模锻压力机drop press曲轴压力机crank press曲柄压力机knuckle-joint press切边压力机trimming press切断压力机cutting-out press精压机coining press辊锻机forging roll镦锻机upsetting forging press喷丸清理sand blast cleaning消除内应力residual stress relieving 水力清理hydraulic blasting酸洗pickling超声波清洗ultrasonic cleaning超声波探伤ultrasonic inspection冲压stamping冲压下料bar stock cutting by punching 冲压线press line凸模punch凸凹模punch-die冲孔模piercing die修边模trimming die预弯模die for first-forming扭弯模twisting die扭弯模twisting die扭弯成形模twisting-forming die 压弯模bending die压弯翻边模bending-flanging die 压扁模flattening die压圆模circular bending die 压弯卷圆模bending-curling die 压弯压筋模bending-beading die 落料模blanking die落料压印模blanking-coining die 落料切槽模blanking-slotting die缩口模neckling die翻孔整形模hole flanging-sizing die 翻边成形模flanging forming die切槽模slotting die拉延模drawing die下料stock cutting开卷unreel成形forming翻边flanging反向拉伸reverse-draw整形restricking整径trued切口cut-off (shear-out) 切边trimming压扁flattening应变strain压痕impression拉延drawing拉伸deep drawng挤压extrusion滚挤roll-forming卷边折边edging刮边scraping三室清洗机three-stage cleaning machine 三动压机triple-action press折边机edging machine开卷机decoiling unit万能液压机universal hydraulic machine 机械压力机mechanical press气动压力机pneumatic press冲孔机punch machine弯曲机弯管机pipe bending machine辊压机rolling press滚式弯板机roll-type sheet bending machine 板料校平机sheet flattening machine退料板stripper高速棒料剪切机high speed cropping machine剪床shearing machine转塔式冲床turret-type punch press校直机straightener挤压机extrusion press滚压挤压机hydraulic extrusion press 卷边机folding machine精压机coining press上料器loader落料机blanker搓丝机thread rolling machine滚剪机roller shearing machine 焊接welding十字接头cross-shaped jointT 形接头T joint单J 形坡口single-J groove单U 形坡口single-U groove双V 形坡口double-V grooveK 形坡口double-vevel groove双V 形对接接头double-V butt jointY 形坡口裂缝试验Y-slit crack testTIG 保护焊tungsten inert gas (TIG) arc welding TIG 点焊TIG spot welding立焊vertical position of welding火焰钎焊brazing by flame气体保护电弧焊gas shield arc welding气焊gas welding气电焊electrogas arc welding水下焊接underwater welding水蒸气保护电弧焊water vapor arc welding水平角焊horizontal fillet welding手工焊manual welding手工电弧焊covered arc welding仰焊face-up bonding正面角焊缝front fillet weld加压气焊gas pressure welding加压铸焊pressure thermit welding 返修焊rewelding向上立焊vertical up welding向下立焊vertical down welding平焊（俯焊）flat position welding点焊point welding双面焊weld from both sides双面点焊direct welding双弧焊twin arc welding压焊pressure welding多道焊multipass welding多点凸焊multiple projection welding 多层焊multilayer welding定位焊tack welding冷压焊cold pressure welding环焊boxing自动焊接automatic welding自动点焊stitch welding自动气割automatic gas cutting无气体保护电弧焊non gas shielded arc welding 对接焊butt welding补焊repair welding深溶焊deep penetration welding滚对焊butt seam welding滚焊seam welding滚点焊roll spot welding横焊horzontal position welding 横向焊缝cross weld金属极惰性气体保护点焊metal inert gas arc welding 金属极电弧焊接metal arc welding电焊eletric welding电子束焊接electron beam welding电子加热钎焊electric brazing电阻焊electric resistance welding 电弧焊electric arc welding堆焊bead welding坡口焊groove welding封底焊道sealing run搭接焊lap welding激光焊接laser welding热焊hot weld单面焊welding by one side单面点焊indirect welding单道焊single-pass welding单层焊single-layer welding单边多点点焊series spot welding单边多电极焊series welding仰焊overhead position welding 熔焊fusion welding氩弧焊argon arc welding跳焊skip welding惰性气体保护焊inert-gas welding埋弧自动焊unionmelt welding碳弧焊carbon arc welding躺焊fire-cracker welding缝焊seam welding锻焊blacksmith welding磁性气体保护焊gas shielded magnetic flux arc welding 焊接工艺welding procedure焊态as-welded焊道bead焊肉致密dense deposits焊后强度as-deposited strength 焊道裂纹bead cracking焊缝seam焊根root of weld焊波ripple焊透complete penetration 未焊透incomplete penetration 焊核nugget熔滴droplet熔敷工艺deposition techniques咬边undercut去渣deslag焊接缺陷weld defects乙炔罐acetylene cylinder乙炔发生器acetylene generator注水式乙炔发生器water to carbide generator投入式乙发生器carbide to water generator乙炔氧焊装置acetylene-welding installation 点焊钳spot welding head三相整流焊机three phase rectifier welder 三相低频焊机three phase low frequency 万能滚焊机universal seam welder手动焊炬hand torch手动焊枪hand held gun压焊机press welder交流弧焊机AC arc welding machine多点焊机multiple spot welder多站电焊机multi-operator welding set 切割机cutting machine气瓶gas cylinder保护罩protective boot电子枪electron gun电阻对焊butt resistance welding电焊机electric welding电弧焊机arc welding machine电渣焊机electroslag welding仿型氧气切割机template-type axy-cutting machine 抽头式焊机welder with taps仰焊机overhead welder单站弧焊机single operator welding machine 移动式焊机portable welding machine移动式接触焊机portable resistance welder移动式点焊机portable spot welder 蓄电池式焊机battery welder缝焊机seam welder大焊丝盘large spool焊工用玻璃welding galss焊工用护目镜welding goggles焊工用面罩helmet shield焊把holder乙炔acetylene电石calcium carbide电极（焊条）electrode手涂焊条dipped electrode合金焊条hastelloy electrode双芯焊条twin electrode双层药皮焊条double coated electrode机械压涂焊条extruded electrode包丝焊条flyspun electrode深熔焊条deep penetration electrode 铁粉焊条iron powder electrode堆焊焊条surfacing electrode碳极carbon electrode机加工machining车削turn高速切削high speed cutting 强力切削power cutting多刀切削multi-tool cutting 深孔加工deep hole working 高速精镗high speed boringh 高速滚削high speed hobbing 平面铣削surface milling镗削boring拉削broaching成型拉削form broaching连续拉削continuous broaching 分层拉削progressive broaching 推削push broaching刨削shaping (planing)磨削grinding外圆磨削cylindrical grinding 内圆磨削internal grinding端面磨削cross grinding周面磨削peripheral grinding 插削slotting铲削relieve钻削drill导电磨削electrical grinding 无心磨削centerless grinding 高速磨削high-speed grinding 强力磨削power grinding珩磨honing研磨lapping超精加工superfinishing齿面加工gear face machining 拉齿broaching gear铣齿gear milling插齿gear shaping滚齿gear hobbing刨齿gear planing剃齿gear shaving研齿gear lapping珩齿gear honing磨齿gear grinding挤齿gear extruding 普通剃齿法general shaving 对角剃齿法diagonal shaving 切向剃齿法tangential shaving剃鼓形齿crown shaving砂带磨削abrasive belt gringding滚压光加工rolling finishing单面切削法single-side cutting method双面切削法spread -blade cutting method展成法切齿gear-cutting with generating method 仿形法切齿gear-cutting with form copying method 成型插齿shear-speed gear cutting花键加工splining螺纹铣thread milling螺纹磨thread grinding镗孔boring hole铰孔ream锪孔counter sinking滚丝thread rolling套丝thread chaing攻丝thread tapping旋风切削螺纹whirl wind cutting thread 少无切削加工non-chip finish挤压光加工extrusion finishing精密加工precision work超精加工superfinishing粗加工rough machining化学机械加工chemical mechanical working 电热加工electro-thermic working阳极机械加工anode mechanical working电脉冲加工electro-spark machining电火花加工electro-spark machining电子束加工electronic beam machining 电解加工electrolytic machining超声波加工ultrasonic machining激光加工laser machining激光硬化laser hardening 油漆paint面漆enamel沥漆区drain area调漆paint mixing浸涂dip-coatng涂底漆priming补漆paint repair喷面漆topcoating热喷漆hot spray打腻子puttying老化weathering人工干燥artificial drying 自然干燥air dry干打磨dry grinding去油（脱脂）degreasing碱法脱脂alkaline degreasing 蒸气脱脂vapor degreasing去离子水demin-water除锈derusting酸洗pickling水洗rinse热水清洗hot water rinse电泳涂层electophoretic coating喷丸处理shot blasting磨光（抛光0burnishing出光glaring罩光glazing磷化预处理phosphating pretreatment 薄膜磷化处理thin amorphous phosphating 湿碰湿wet-to-wet钝化passivating结皮现象skinning起皱wrinkling遮蔽masking凉干flash off气幕air seal喷漆室booth干式喷漆室dry spray booth水过滤式喷漆室water wash spray booth下吸式喷漆室down draft spray booth侧抽风喷漆室spray booth of side exhaust 油漆调制室paint mixing room打磨间scuff sand booth通过式烘干室passing through type baking oven 桥式烘干室bridge type baking oven辐射对流烘干室joint radiation convection oven 浸漆设备dip equipment浸漆槽dip tank循环槽recirculating tank自动喷漆机automatic sprayer热喷漆机flow coating equipment淋漆设备flow coating equipment手工浸漆设备hand dip equipment无空气喷涂设备airless spray equipment电泳涂漆设备electro apparatus电涂漆设备electrocoating installation 静电喷漆设备electrostatic spray equipment 喷枪spray gun双头喷枪double head spray gun空气喷枪air spray gun吊具sling推杆悬链double-chain conveyer悬挂运输链overhead conveyer油水分离器oil-water separator油漆调制罐paint mixing tank除尘装置dust collector静电除尘装置electrostatic dust collector 阴极罩cathode shiedl超滤装置ultrafiltration device喷砂机sand blasting machine红外线固化IR curing紫外线固化UV curing电子束固化electron beam curing辐射固化漆膜radiation cured coating (RCC) 光泽计glossmeter比重计gravimeter粘度计viscosimetr细度计fineness gauge厚度计thickness gauge遮盖力测定仪cryptometer电镀electroplating预镀（冲镀）striking防镀（止镀）resist无氰电镀non-cyanide plating 化学电镀electroless plating 气相电镀vapor plating挂镀rack用假阴极电镀dummying机械电镀mechanical plating 浸镀immersion plating 退镀stripping滚镀barrel plating电解沉积electrowinning混浊度turbidity侵蚀fretting侵渍作用maceration亲水的hydrophilic疏水的hydrophobic絮凝剂flocculant光亮镀层bright coating防腐镀层coating for protection against corrosion 冲洗flush打光lapping抛光burnishing滚光tumbling变色tarnishing电解electrolysis沉淀法decantation抗暗处理anti-tarnish treatment均镀力levelling power深镀能力covering power酸洗pickling磷化phosphating镀锌galvanizing漂白whiten出斑点spotting out电镀机plating machine自动电镀装置automatic plating machine直线式电镀机straight-line plating machine 挂式电镀机plating machine held on racks钟形滚镀机oblique-barrel plating machine 微型滚镀机portable plating barrel冷水槽cold rinse bank双联冷水槽double countercurrent rinse tank 电解去油槽electrolytic cleaner衬铅槽lead lined steel tank哈林电槽haring cell热水槽hot rise tank超声波去油槽ultrasonic cleaning tank浸酸槽acid dip tank温水槽warm rinse tank赫尔槽hull cell镀锌槽zinc-plating tank固定槽plating tank回收槽reclaim tank水平全浸式滚筒horizontally fully-immersed barrel 六角滚筒hexagonal plating barrel孔板流量计orifie meter浊度计nephelometer库仑计coulometer滴重计stalagmometer汽车制造设备manufactruing equipment of automobile 万能铣床universal milling machine内外圆研磨床inner-outer happing machine仿形车床copy lathe龙门刨床double housing planer牛头刨床shaper攻丝机threading machine双柱坐标镗床double pillar jig borer滚丝机thread roller滚齿机hobbing machine钻床drilling machine插床slotting machine珩齿机gear honing machine平衡-钻中心孔机床balancing centering machine曲轴车床crankshaft turning lathe双工位曲轴车床double-post carnkshafttruning blathe曲轴（主轴颈）车床crankshaft (main journal turning lathe) 凸轮轴（轴颈）车床camshaft(journal )turning lathe液压仿形车床dydraulic coping lathe凸轮轴仿形车床camsahft coping lathe多轴深孔钻床multi-spindle deep hole drilling machine 曲轴轴颈铣削专用机床crankshaft journal milling machine数控曲轴铣床N/C crankshaft milling machine螺纹铣床thread milling mahcine球面蜗杆铣床cone-worm milling machine花键轴铣床spline shaft milling mahcine转鼓铣床drum milling machine旋风式曲轴铣床whirl-wind type crankshaft milling machine 曲轴主轴颈磨床cranksahft journal grinding machine凸轮轴磨床camshaft grinding machine螺纹磨床thread grinding machine活塞销超精加工机piston pin superfinishing machine弹簧端面磨床grinding machine for spiral spring活塞椭圆磨床。
最新机械专业英语词汇大全-中英对照
机械制图Mechanical drawing画法几何descriptive geometry投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion 车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear 虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower 对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series 高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism 机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation 机械无级变速mechanical stepless speed changes 基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM 计算机集成制造系统computer integrated manufacturing system, CIMS计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio 角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel 联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements 挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset 偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use 起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact 气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass 少齿差行星传动planetary drive with small teeth difference设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s coupling矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal。
机械类词汇中英文对照表
机械类词汇中英文对照表（字母L）l head cylinder l 形头气缸la mont boiler 拉孟特锅炉label glueing machine 贴商标机label printing machine 标签印刷机labelling machine 贴商标机labile equilibrium 不稳定平衡labor productivity 劳动生产率laboratory 实验室laboratory centrifuge 实验室用离心机laboratory instrument 实验室仪器laboratory test 实验室试验labour productivity 劳动生产率labyrinth 迷宫labyrinth packing 曲径密封垫片labyrinth seal 曲径密封垫片lack of fusion 未焊透lacquer 漆lacquer enamel 珐琅lacquering 涂漆ladle 铸桶ladle crane 浇注起重机ladle truck 铸桶车laedscrew machine 丝杠加工机床lag 延迟lagging 保温lagrange s equation 拉格朗日方程lagrangean function 拉格朗日函数lam 激光非晶化lambert s law 朗伯定律lamellar pearlite 片状珠光体lamellar spring 迭板殚簧lamellar structure 片状组织laminar boundary layer 层吝界层laminar convection 层猎流laminar flow 层流laminar motion 层了动laminate 层压材料laminated pearlite 片状珠光体laminated plate 叠层板laminated spring 迭板殚簧laminating machine 层压机laminating method 被覆淋膜成形lamp oil 灯油lancashire boiler 兰开夏式火管锅炉lancing die 切口弯曲模land 导向边land boiler 陆地锅炉land area 合模面land wheel 地轮landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具landing craft 登陆艇landing distance 着陆距离landing flap 着陆襟翼landing gear 起落架landing light 着陆灯landing skids 起落橇language controlled robot 语言控制机扑lantern gear 灯笼齿轮lantern pinion 灯笼齿轮lanthanum 铜lap 研磨lap grinding 研磨lap joint 搭接lap machine 研磨机lap welded pipe 迭焊管lap welded tube 迭焊管lap welding 搭焊laplace operator 低量算符laplace transformation 拉普拉斯变换laplacian 低量算符lapped joint 搭接lapping 研磨lapping compound 研磨剂lapping joint 搭接lapping machine 研磨机lapping paste 研磨剂lapping plate 研磨板lapping tool 研磨具large calorie 千卡large calory 千克卡large end 大端large lot production 大批生产large scale integration 大规模集成电路large size machine tool 大型机床laser amorphousizing 激光非晶化laser annealing 激光退火laser beam 激光束laser beam bending 激光弯曲laser beam cutting 激光切割laser beam drier 激光束干燥器laser beam drilling 激光钻孔laser beam grooving 激光开槽laser beam machining 激光加工laser beam welding 激光焊接laser bending 激光弯曲laser boronizing 激光渗硼laser carbonitroboronisation 激光碳氮硼共渗laser carbonitroboronizing 激光碳氮硼共渗laser condensation 激光致密化laser cutter system 激光切系统laser cutting machine 激光切割机laser doping 激光搀杂laser drill 激光钻机laser engraving machine 激光刻花机laser enhanced electroplating 激光增强电镀laser fusion 激光核聚变laser grooving 激光开槽laser hardening 激光硬化laser heating 激光加热laser helical turning 激光螺旋形车削laser interferometer 激光干涉仪laser level 激光水平仪laser machine 激光加工机床laser magnetic domain control 激光磁畴控制laser mirror 激光镜laser patterning 激光制图laser process machine 激光加工机床laser quenching 激光淬火laser recorder 激光记录仪laser resonator 激光谐振腔laser ring turning 激光环形车削laser scribing machine 激光划片机laser sensor 激光传感器laser shock hardening 激光冲徊化laser stereo lithography 激光立体制版laser welding 激光焊latch 掣子latch needle 舌针late ignition 延迟点火latent heat 潜热latent heat of condensation 凝结潜热latent heat of fusion 融解潜热latent heat of liquefaction 液化潜热latent heat of solidification 凝固潜热latent heat of sublimation 升华潜热latent heat of vaporization 蒸发潜热lateral force 侧力lateral load 横向负载lateral oscillation 横振动lateral pressure 旁压力lateral section 横断面lateral stability 横向稳定性lateral strain 横向应变lateral stress 横向应力lateral vibration 横振动lateral wall 单侧墙latex 乳汁lathe 车床lathe bed 车床床身lathe carrier 车床夹头lathe chuck 车床夹盘lathe dog 车床夹头lathe spindle 车床轴lathe tool 车刀lathe turning 车削车床加工lathe work 车工工作lattice 格子lattice girder 桁架梁lattice structure 晶格结构launch 下水launching 下水launching ways 下水台laundry machine 洗衣机laval nozzle 拉伐尔喷管law of conservation of energy 能量守恒律law of conservation of mass 质量守恒定律law of mass action 质量酌定律law of partial pressure 道尔顿法则law of similarity 相似定律law of similitude 相似定律law of thermodynamics 热力学定律law of universal gravity 万有引力定律lawn mower 剪草机lay 加工痕迹方向layer 层layout of cam profile 凸轮廓线绘制layout plan 布置图lb 激光渗硼lbb 激光弯曲lbg 激光开槽lc 激光致密化lcd 液晶显示器lcnb 激光碳氮硼共渗ld 激光搀杂leaching 浸析lead 螺纹导程lead acid battery 铅板蓄电池lead alloy 铅合金lead angle 导程角lead angle at reference cylinder 分度圆柱导程角lead bath 铅浴lead bath furnace 铅浴炉lead bronze 铅青铜lead hardening 铅浴淬火lead in cable 引入电缆lead in insulator 引入绝缘子lead in wire 引入线lead of screw thread 螺纹导程lead paint 铅丹lead pipe 铅管lead quenching 铅浴淬火lead rail 导轨lead screw 进给丝秆lead sheathed cable 铅皮电缆lead wire 引入线leaded gasoline 加铅汽油leading axle 导轴leading bogie 前转向架leading current 导前电流leading edge 前缘leading screw 丝桢leading truck 前转向架leading wire 引入线leaf filter 叶状滤器叶片式过滤器leaf spring 板簧leak 渗漏leak detection 泄漏探测leak detector 泄漏探测器leak tight structure 密封结构leakage 渗漏leakage coefficient 漏泄系数leakage compensation 泄漏补偿leakage current 漏电流leakage flux 漏磁通leakage loss 泄漏损失leakage test 泄漏试验leakproof material 密封材料leakproof structure 密封结构leakproofness 气密性lean gas 贫气lean mixture 稀混合气lean sand 瘦砂learning control 学习控制learning machine 学习机learning program 学习程序learning robot 学习机扑least square method 最小二乘法leather 皮leather belt 皮带leather cuff 皮碗leather cup 皮碗leather packing 皮革填料leather substitute 人造革leclanche cell 勒克兰舍电池led 发光二极管ledeburite 莱氏体left hand helix 左向螺旋线left hand screw 左转螺钉left hand steering 左置转向left hand thread 左旋螺纹left hand tool 左切刀left hand worm 左旋蜗杆left view 左视图leftward welding 左向焊lemniscate 双纽线length 长度length measuring machine 测长机length of action 啮合长度length of line of action 啮合线长度length of thread engagement 配合长度length overall 全长length to diameter ratio 直径长度比lens 透镜lens current supply 透镜电源lens grinding machine 透镜研磨机lep 激光增强电镀letter sorting machine 信件分选机level 水准仪level control 水平控制level indicator 液面指示器level of energy dependency 能源依存性level of significance 显著性水平level sensor 水平传感器level switch 开关leveler 平整机leveling block 平台levelling 水准测量levelling agent 匀涂剂lever 杆lever arm 杠杆臂lever brake 杆式制动器lever handle 杠杆手柄lever motion 杠杆机构lever press 杠杆式压力机lever ratio 杠杆率lever riveter 杠杆式铆钉机lever shears 杠杆式剪切机leverage 杠杆率lf 激光熔融lht 激光螺旋形车削library 丛书lid 盖life 寿命life test 寿命试验life time 寿命lifeboat 救生艇lifeguard 排障器lift 升降机lift check valve 阀lift coefficient 升力系数lift drag ratio 升阻比lift of pump 泵的压头lift pump 升水泵lift truck 起重汽车lift valve 提升阀lifter 挺杆lifter guide 挺杆导管lifting capacity 起重能力lifting chain 起重链lifting drum 起重卷筒lifting gear 提升机构lifting hook 起重钩lifting magnet 起重磁铁lifting motor 卷扬电动机lifting rope 起重绳lifting speed 提升速度light airplane 轻型飞机light alloy 轻合金light car 轻型人汽车light cross country truck with all wheel drive 全轮驱动越野轻型货车light duty 轻负荷light emitting diode 发光二极管light energy 光能light filter 滤光器light flux 光通量light industry 轻工业light load 轻负荷light metal 轻金属light oil 轻油light sensitivity 感光性light source 光源light truck 轻型载货汽车light van 轻型厢式送货车light water reactor 轻水反应堆lighter than air aircraft 轻航空器lighter than aircraft 轻航空器lighting 照明lighting device 照冒置lighting dynamo 照妹发电机lighting engineering 照眉术lighting installation 照描备lighting system 灯光系统lightning arrester 避雷器lightning conductor 避雷针lightning protector 避雷器lightning rod 避雷针lightweight construction 轻量构造lightweight structure 轻量构造lignite 褐煤lignumvitae 铁梨木limb 分度弧limbus 圆形刻度lime 石灰lime mortar 石灰浆lime spreader 石灰撒布机limestone 石灰石limit 限度limit gage 极限规limit load 极限负荷limit load design 极限载荷设计limit of elasticity 弹性极限limit of proportionality 比例极限limit of size 极限尺寸limit of wear 磨损极限limit plug gage 极限塞规limit size 极限尺寸limit switch 限制开关limited interchangeability 不完全互换性limiting speed 极限速度limiting value 极限值limits of tolerance 公差范围limonite 褐铁矿limousine 高级轿车line 线line contact 线接触line integral 线积分line of action 啮合线line of centers 连心线line of collimation 视准线line of contact 啮合线line of flow 吝line of force 力线line of shafting 轴系line printer 行式打印机line spectrum 线状光谱line voltage 线电压line welding 滚焊lineal 线linear acceleration 线加速度linear accelerator 直线加速器linear approximation 线性近似linear displacement 线位移linear encoder 直线式编码器编码尺linear equation 线性方程linear expansion 线膨胀linear interpolation 直线插值linear (circle) interpolator 线形（圆形）插补器linear motion 直线运动linear motor 直线电动机linear programming 线性规划linear shrinkage 线收缩linear system 线性系统linear transducer 线性变换器linear transfer machine 线性自动机床linear velocity 线速度linearity 线性linearization 线性化liner 客轮lining 炉衬lining ring 衬垫linishing 砂带磨削link 构件link belt 链带link chain 环链link fuse 链熔线link gear 摇拐机构link motion 摇拐机构link pin 链销link polygon 肃边形linking 联机linoleum 油布linotype 莱诺排铸机linseed oil 亚麻仁油lip 切闲lip packing 唇形密封件liquation 偏析liquefaction 液化liquefaction plant 液化装置liquefied gas 液化气liquefied natural gas 液化天然气liquefied natural gas tanker 液态天然气运输船liquefied petroleum gas 液化石油气liquefied petroleum gas engine 液化气发动机liquefier 液化器liquid 液体liquid air 液态空气liquid ammonia 液氨liquid carburizing 液体渗碳liquid chromatography 液色谱法liquid cooling 液体冷却liquid crystal display 液晶显示器liquid damping 液体阻尼liquid expansion thermometer 液体温度计liquid friction 液体摩擦liquid fuel 液体燃料liquid gas 液化气liquid helium 液氦liquid honing 液体研磨liquid in glass thermometer 玻璃管液体温度计liquid jet machining 液体喷射加工liquid laser 有机染料激光器liquid level indicator 液面仪liquid lubrication 液体润滑liquid manure spreader 厩液撒布机liquid metal 液体金属liquid metal fuel 液态金属燃料liquid metal heat exchanger 液态金属热交换器liquid nitrogen 液态氮liquid oxygen 液态氧liquid packing 液体垫片liquid phase 液相liquid propellant 液体推进剂liquid propellant rocket 液体推进剂火箭liquid propellant rocket engine 液体火箭发动机liquid seal 液封liquid separator 液体分离器liquid spring 液体弹簧liquid state 液态liquid thermometer 液体温度表liquidity 流动性liquidus 液相线lissajous figure 利萨如图形liter 公升lithium cell 锂电池lithium grease 锂基润滑脂lithographic printing press 石版印刷机litmus paper 石蕊试纸litre 升live axle 驱动轴live center 活顶尖live load 移动载荷live roller conveyor 机动滚道输送器live steam 活蒸汽live steam heating 新汽取暖ljm 液体喷射加工ljungstrom air preheater 永司登空气预热器ljungstrom turbine 永司登透平lmdc 激光磁畴控制lng 液化天然气load 负载load balancing mechanism 均衡装置load capacity 负荷能力load carrying capacity 负荷能力load cell 测力传感器load centre 负荷中心load chain 起重链load characteristic 负荷特性load current 负载电流load curve 负荷曲线load—deformation curve 载荷—变形曲线load deformation diagram 载荷变形图load diagram 负荷曲线load distribution 负载分布load factor 负荷系数load limiter 负载限制器load on axle 车轴负载load on spring 簧上负载load rating 额定载荷load rope 起重绳load test 带负荷试验load water line 满载吃水线loader 装载机loader shovel 装载机铲斗loading 堵loading and unloading 装卸loading handler 装载机械手loading history 加载履历loading robot 装载机器人loading shoe mold 料套式模具loading shovel 装载机铲斗loading station 装载站loading test 带负荷试验loading time 装载料时间loading unloading 装卸loam 造型粘土loam mold 粘土铸型loam molding 粘土造型loam mould 粘土型local cell 局部电池local corrosion 局部腐蚀local hardening 局部淬火local heat treatment 局部热处理local heating 局部加热;局部供暖local illumination 局部照明local lighting 局部照明local pressure loss 局部压力损失local stress 局部应力locating 定位locating center punch 定位中心冲头locating device (face,element) 定位装置（面，元素）locating device 定位装置locating element 定位零件（定位要素）locating face 定位面locating pilot pin 定位导梢locating pin 定位销（挡料销）locating plate 定位板locating ring 定位圈locating rule 定位尺locating washer定位垫片lock 锁lock nut 防松螺母lock screw 止动螺钉lock seaming 固定接合lock washer 止动垫圈locking 锁住locking lever 摇杆locking plate 定位板locksmith 钳工locomobile 锅驼机locomotive 机车locomotive boiler 机车锅炉locomotive crane 机车起重机locomotive with storage battery 蓄电池机车log 测程仪logarithm 对数logarithmic decrement 对数衰减率logarithmic mean temperature difference 对数平均温差logarithmic scale 对数刻度logarithmic spiral 等角螺线logging tractor 集材拖拉机logic algebra 逻辑代数logic analysis 逻辑分析logic circuit 逻辑电路logic element 逻辑单元logical analysis 逻辑分析logical circuit 逻辑电路logical operation 逻辑运算long distance coach 长途公共汽车long flame coal 长焰煤long term strength 长期负荷强度long time test 长期试验longitude 经度longitudinal 纵向的longitudinal axis 纵轴longitudinal beam 纵梁longitudinal feed 纵进刀longitudinal force 纵向力longitudinal grinding 纵磨longitudinal movement 纵向运动longitudinal oscillation 纵振动longitudinal rolling 纵轧longitudinal seam 纵接缝longitudinal section 纵切面longitudinal stability 纵向稳定性longitudinal vibration 纵振动longitudinal wave 纵波loom 织机loop 波腹loop a line 环路法连接线路loop scavenging 回哩气loop tenacity 环结强度looping mill 环轧式轧钢机loose detail mold 活零件模具loose fit 间隙配合loose pulley 空转轮loose side 松边loosen the key 抽出缝lorentz force 洛伦兹力lorry 载重汽车loss 损失loss angle 损失角loss factor 损失率loss of energy 能的损失lost motion 空动lost wax casting process 失蜡铸造法lot 批lot production 成批生产loud speaker 扬声器louver 百叶窗low alloy steel 低合金钢low alloy tool steel 低合金工具钢low calorific power 低热值low calorific value 低热值low capacity machine 小功率机床〔机器〕low carbon steel 低碳钢low compression engine 低压发动机low electrode wear machining 低损耗加工low frequency 低频率low frequency furnace 低频电炉low frequency induction melting furnace 低频感应熔化炉low grade coal 劣质煤low grade fuel 劣质燃料low manganese casting steel 低锰铸钢low melting alloy 易熔合金low melting metal 低熔点金属low noise 低噪声的lower pair 低副low pressure casting 低压铸造low pressure boiler 低压锅炉low pressure burner 低压燃烧嘴low pressure casting 低压模铸low pressure chamber 低压室low pressure compressor 低压压气机low pressure cylinder 低压汽缸low pressure engine 低压发动机low pressure fan 低压通风机low pressure stage 低压段low pressure steam engine 低压蒸汽机low pressure steam heating 低压蒸汽供暖low pressure tire 低压轮胎low pressure turbine 低压透平low pressure turbine pump 低压汽轮泵low pressure tyre 低压轮胎low speed diesel engine 低速柴油发动机low temperature 低温low temperature annealing 低温退火low temperature carbonization 低温干馏low temperature distillation 低温干镏low tension electric ignition 低压点火low tension ignition 低压点火low tension winding 低压线圈low thermal inertia furnace 低热惯性炉low thermal mass furnace 低热惯性炉low vacuum 低真空lower calori fic value 低热值lower calorific value 低热值lower dead center 下死点lower dead centre 下死点lower deviation 下偏差lower die 下模lower limit 下限尺寸lp 激光制图lpg 液化石油气lpr 液体推进剂火箭lrt 激光环形车削l-section 组装列表lsh 激光冲徊化lsi 大规模集成电路lsl 激光立体制版lublicator 注油器lubricant 润滑剂lubricant additive 润滑剂的添加剂lubricant film 润滑油膜lubricant pump 润滑油泵lubricating can 注油罐lubricating device 润滑装置lubricating equipment owge 润滑用具lubricating film 油膜lubricating grease 滑脂lubricating nipple 油嘴lubricating oil 润滑油lubricating oil consumption 润滑油消耗量lubricating oil tank 润滑油箱lubricating pad 油垫lubricating point 润滑点lubricating pump 润滑油泵lubricating ring 润滑油环lubricating system 润滑系统lubricating wick 润滑灯芯lubrication 润滑lubrication chart 润滑图表lubrication device 润滑装置lubrication diagram 润滑图表lubrication engineering 润滑工程lubrication groove 润滑油槽lubricator 注油器lubricity 润滑性lug 耳lumber carrier 木材运输船lumen 流luminance 辉度luminescence 荧光luminescent paint 发光涂料luminious source 光源luminous flame 光焰luminous flux 光通量luminous intensity 光度lump coal 块煤lumped mass 集中质量lumped parameter system 集中参数系统lunar probe 月球探测器lunar rover 月球车luster 光泽lux 勒luxmeter 勒克司计lwr 轻水反应堆lye 碱液lyophilisation 冷冻干燥lyophilizer 冷冻干燥。
机械类专业词汇中英文对照翻译表大全
机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics; human engineering人体尺寸 human dimension人体测量学 anthropometry; anthropometrics刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver 丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角尺 set square三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰?胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellac士巴拿；扳手 spanner大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB)小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench; working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU)中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF) 中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies 分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltage divider隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off 切断工具 parting tool勾；勾脚 hook勾刀；胶片?刀 plastic cutter 化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier 反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe; woodworking lathe木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB) 水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch五画丙烯?丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fitting凸轮传动 cam drive凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining 半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon; polyamide (PA)尼龙墨水针笔 technical felt-tip pen左右调校杆 lateral adjusting level市售尺寸；标准尺寸 stock size市电频率；电源频率 mains frequency平(木)锉 flat rasp平水尺；水平仪 spirit level平行投影 parallel projection平行车削 parallel turning平行虎钳 parallel vice平行钉法 parallel nailing平底弯刨 flat faced spokeshave平底钻嘴 forstner bit平板结构 slab construction平流扼流圈；滤波扼流器 smoothing choke平流电容器；滤波电容器 smoothing capacitor 平流电路；滤汳电路 smoothing circuit平面板；正台 surface plate平面图；俯视图 plan平面锤 flatter平移 translation平搭榫 corner halving joint平嘴钳 flat nose pliers平槽刨 router plane平衡 balance; equilibrium平衡力 equilibrant平衡条件 equilibrium condition平衡电桥 balanced bridge平头弧刀 square nose gouge幼纹 smooth cut打凹成形 hollowing打凸成形 raising打槽机 routing machine打线；打槽 routing打磨 fitting; polishing打磨机 polisher本生灯 Bunsen burner本征半导体 intrinsic semiconductor 正反器；触发器；复振器 flip-flop 正反馈；正回输 positive feedback 正火 normalizing正向偏置 forward bias正投影 orthographic projection正投影图 orthographic drawing正弦波形 sinusoidal waveform正面投影 front projection正视图 elevation; front elevation 正极；阳极 anode正齿轮 spur gear正台；平面板 surface plate永久性接合 permanent joining瓦通纸；瓦楞纸板 corrugated board生长层 cambium layer生产图 production drawing生胶浆 rubber cement生钢；铸钢 cast steel生铁；铸铁 cast iron用途；功能 function白杨木 poplar白胶浆 PVA glue; white glue皮沙垫 leather sandbag皮革 leather皮革黏合剂 leather glue皮鞋 leather shoes目录 contents矢量；向量 vector石灰岩 limestone石英晶体振荡器 quartz crystal oscillator石棉 asbestos; asbestus石膏 Plaster of Paris示波器 oscilloscope立体图 pictorial drawing六画交流电流 alternating current (a.c.)交流电压 a.c. voltage交联结构 cross-linked structure仿饰金 gilding metal伏特 volt光力架 clear lacquer光拉软钢 bright drawn mild steel (B.D.M.S.) 光敏电阻 light dependent resistor (LDR)光测弹性学 photoelasticity光刨；滑刨 smoothing plane光电效应 photoelectric effect光泽 lustre全闭式槽榫 closed housing joint共面力 coplanar force共聚合作用 co-polymerization共聚物 copolymer共价键 covalent bond共振；共鸣；谐振 resonance印刷电路板 printed circuit board (PCB)同素异形 allotropy同轴电缆 coaxial cable同温 equality of temperature向量；矢量 vector向量和 vector sum104合力 resultant force合口扁钳 close mouth tongs合成色；等和色 secondary colour合成品 composite合成粅料 composite material合金 alloy合金工具钢 alloy tool steel合钉；定位销 dowel回火 tempering回复力 restoring force回复力偶 restoring couple回弹 resilience回输；反馈 feedback地线 earth wire多刃切削刀具 multi-point cutter多孔塑料；泡沫塑料；海绵状塑料 foam plastics多方榫接合 pinned joint多媒体 multi-media多晶性 polycrystallinity多谐振动器；多谐振荡器 multivibrator 多边形力学；力多边形 polygon of force 字母冲 letter punch字板 letter stencil安全 safety安全守则 safety rule安全系数 safety factor安全措施 safety precaution105安全眼罩 safety goggle安全设备 safety equipment安全药箱 safety box安培 ampere安培计；电流表 ammeter尖脚 spur年轮 annual ring成本 cost成形 forming扣件；击固件 fastener扣钉 clout nail; cramp托架 bracket收缩 shrinkage曲柄 crank曲柄轴 crank shaft曲线规；云板；云尺 French curve有效的 efficient有效电流 effective current灰；灰末 ash百折胶；百折胶；聚丙烯 polypropylene (PP) 竹 bamboo羊角锤 claw hammer老化 ageing肋条 rib肌理；质感；质地 texture自由度 degree of freedom自动控制 automatic control106自动进给 auto-feed自然干燥法 natural seasoning自感量 self-inductance自感应 self-induction色彩；颜色 colour色调 tone色环 colour wheel行星齿轮；周转齿轮 epicyclic gear七画肘节开关 toggle-switch串激电动机；串绕电动机 series-wound motor 位能；势能 potential energy位梯度；势梯度 potential gradient位移 displacement位错 dislocation伸长度 elongation作工硬化 work hardening作功 work done作图线 construction line低密聚乙烯 low density polyethylene (LDPE) 低通滤波器 low-pass filter低电压 low voltage低碳钢 low carbon steel布置 layout免油轴承 oil-less bearing冷加工；冷作工 cold working冷加工硬化 cold work hardening冷色 cool colour冷轧压 cold rolling冷却系统 cooling system冷却效应 cooling effect冷却液流量 coolant rate冷凝胶；环氧树脂 epoxy resin108利口；「披」口；铁屑 burr刨平 planing刨花板；碎料板 particle board吹风机 air blower吹气模塑；吹模塑 blow moulding吹管 blow pipe含铁金属 ferrous metal含水量 moisture content坑凿 cross-cut chisel均方根值 root mean square value均角投影图；等角投影图 isometric drawing 均速圆周运动 uniform circular motion 夹；夹钳 clamp夹 cramp夹卡 mounting board夹具 fixture; jig夹具及固定装置 jig and fixture夹板；胶合板 plywood夹持工具 clamping device; holding tool夹背锯；榫锯 tenon saw夹头 chuck夹头开启匙；夹头扳手 chuck key夹叠黏合成形 lamination尾座 tailstock床身；床道 lathe bed床鞍；刀座帷 apron形心；面心 centroid109形状 shape形变 deformation「快把」板；硬质纤维板 hardboard快速移位 rapid traverse抗扭强度 torsional strength抗屈强度 bending strength; yield strength 抗性分量；无功分量 reactive component抗拉强度 tensile strength抗氧化剂 anti-oxidant抗剪强度 shearing strength抗磁性物料 diamagnetic material抗挠性 stiffness抗压强度 compressive strength抗断强度 breaking strength技术员；技师 technician扶架 steady扭力 torsion扭矩；转矩 torque扭转 torsion扭转角 angle of torsion把手 hand grip扼流圈 choke扳手 spanner; wrench投影 projection投影面 projection plane投影线 projection line攻丝 tap材料 material材料单；材料表 material list杜拉铝 duralumin杉木 spruce步进电动机 stepper motor步冲轮廓法 nibbling每分钟转数 revolution per minute (r.p.m.) 系统组件 system component角托架 angle bracket角位移 angular displacement角板；直角板 angle plate角度 angle角榫 corner angle joint; corner joint角铁 angle iron谷巴凡立水 cobal varnish车刀架 tool holder车床 lathe车床工具 lathe tools车床中心钻咀 lathe centre bit车床操作法 lathe operation车削；车旋 lathe turning; turning车削工具 turning tools防火胶板 Formica防锈 rust prevention防声耳筒；护耳器 ear-protector防松螺帽 lock nut防护装置；保护罩；保护网 guard; safety guard八画注射成形法；喷射铸造法 injection moulding并激电动机；并绕电动机 shunt-wound motor乳酪胶 casein glue乳胶漆 emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)亚稳态的；介稳态的 metastable来回摆动 oscillating两点透视 two-point perspective刻度；划线 ruling刺冲 dot punch刮刀 scraper刮擦 scraping制动鼓 drum brake制动碟 disc brake制动器 brake受迫振动 forced vibration受迫振荡 forced oscillation和谐 harmony周转齿轮；行星齿轮 epicyclic gear固定夹；台夹 bench holdfast固定负载 dead load定子 stator定位销；合钉 dowel定位螺丝 set screw定距轮 stitch marker屈片机 folding machine屈曲 bending屈服点；降服点 yield point屈圈法 loop forming屈卷法 scrolling屈接缝 folded lap seam屈喉机 tube bender屈折 folding屈折线 folding line屈压接缝 folded & grooved seam延性 ductility延性的 ductile弦锯法 plain sawing弧口凿；圆凿 gouge往复式运动 reciprocatory motion拉力 tensile force拉力计；张力计 tensiometer; tensometer拉钉 blind rivet; pop rivet拉钉接合 blind riveting; pop riveting拉钉钳 blind riveting pliers; pop riveting pliers 拉张 tension拉张应力 tensile stress拉张应变 tensile strain拉细 drawing-down拉制法 drawing拉线 wire drawing「披」口；利口；铁屑 burr拔钳 nippers拋光 buffing拋光机 buffing machine放大；扩大 enlargement放大尺 pantograph放大倍数 amplification factor放大器 amplifier放电极加工；火花电蚀法 electrical discharge machining 易用万能尺 line setter易碎 fragile〈绘画的〉明暗运用；描影 shading枝；杆 rod杯形顶尖 cup centre杯头螺丝 hexagonal socket head cap screw板锯 panel saw松木 pine松节水 turpentine法式磨光 French polishing法拉〈电容量单位〉 farad油石；磨刀石 oil stone油漆；涂料 paint泡沫塑料；多孔塑料；海绵状塑料 foam plastics物理特性 physical property物理属性 physical attribute物理量 physical quantity盲孔；闭孔；不贯穿孔 blind hole直尺 ruler; straight rule直角叉榫 corner bridle joint直角尺 try square直角板；角板 angle plate直角杠杆 bell crank lever直身钻嘴 straight shank drill直车刀架 straight tool holder直流发电机 d.c. generator直流电流 direct current (d.c.)直流电动机；直流马达 d.c. motor直纹锯 rip saw直线切削 linear interpolation直线运动 rectilinear motion直边凿；方边凿 firmer chisel直铁剪 straight snips硅 silicon空行程 idle stroke空气动力学 aerodynamics空间 space空载 no load花纹凿 embossing stamp花梨木 rosewood花样；图案 pattern虎克定律 Hooke's Law虎钳 vice虎钳护罩 vice clamp初步意念 proposed solution表面 surface表面展开图 surface development表面张力 surface tension表面处理 surface finishing; surface treatment 表面硬化 case hardening表面硬化钢 case-hardened steel表达方式 presentation表达技巧；传意技巧 communication technique表观膨胀；视膨胀 apparent expansion金工 metalwork金工工作间 metalwork area金工角尺 engineering square金工车床 metalwork lathe金工虎钳 engineer's vice金工锯床 power hacksaw金属包头；金属箍 ferrule金属配件 metal fittings金属线 wire金属压展机 hand rolling mill金属擦光剂；磨光剂 metal polish金属薄片 sheet metal金属键 metallic bond长方通 rectangular tube长刨 trying plane长螺旋钻咀 long auger bit长镗孔 long boring闸极 gate阻抗 impedance附件 attachment附录 appendices青铜 bronze非反相放大器 non-inverting amplifier非本征半导体 extrinsic semiconductor非破坏性试验 non-destructive testing非晶状固体 amorphous solid非顽磁性铁磁材料 non-retentive ferromagnetic material 非压缩性流体 incompressible fluid非稳态 unsteady state非铁金属；不含铁金属 non-ferrous metal九画亮漆；力架 lacquer信号 signal信号产生机 signal generator信号处理 signal processing保养；维修 maintenance保险丝 fuse保护罩；保护网；防护装置 guard; safety guard促凝剂 accelerator削屑 swarf垂直投影面 vertical plane型砧 swages〈书的〉封皮 binding封面 cover急回机构 quick return mechanism 扁枝 bar扁头 cross-pein扁头法 upsetting扁头铆钉 flat head rivet扁头螺丝 flat head screw扁凿 flat chisel指示器 indicator指形榫 finger joint施力 effort染色 staining染色剂 stain架构 framework柄 stock柚木 teak柳安木 lauan。
(机械制造行业)机械专业中英文对照翻译大全
（机械制造行业）机械专业中英文对照翻译大全机械专业英语词汇中英文对照翻译一览表陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center 车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine 拉孔broaching装配assembling铸造found流体动力学fluid dynamics 流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor 集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting 相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant 逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed 变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross 槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism 串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes 动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics 反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism 复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism 刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment 公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design 共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling 滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation 技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions 计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturingsystem, CIMS计算力矩factored moment; calculation moment 计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism 减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair 空间运动链spatial kinematic chain 空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action 隶属度membership力force力多边形force polygon。
机械类专业词汇中英文对照翻译表大全.
机械类专业词汇中英文对照翻译表大全?机械类专业词汇表一画一字螺丝批slot type screwdriver一点透视one-point perspective二画二合一黏合剂epoxy resin adhesive二合胶;混合胶epoxy glue二维的;平面的two-dimensional二进制binary二极管;整流子diode二号螺丝攻second tap二路开关two-way switch十进制的;公制的metric人工制品artefact人造板man-made board人体工程学ergonomics; human engineering 人体尺寸human dimension人体测量学anthropometry; anthropometrics刀片blade刀身blade刀具tool刀具溜座carriage刀柱tool post刀架tool rest刀架底座tool rest bracket刀座帷;床鞍apron刀座鞍;溜板座saddle力force力三角形triangle of force力平行四边形parallelogram of force 力多边形;多边形力学polygon of force 力的分解force resolution力架;亮漆lacquer力矩moment力偶couple力矩定律law of moment力-距离图表force-distance graph力图force diagram力线line of force力点effort十字榫cross halving joint十字螺丝Philip's head screw十字螺丝批Philip's type screwdriver 丁字尺;T 尺tee square三画三爪夹头three-jaw chuck三角尺set square三角形结构系杆triangulation tie三角锉triangular file三维的;立体的three-dimensional三氯甲烷;哥罗芳chloroform三聚氰?胺;蜜胺melamine三点透视three-point perspective上油漆painting上釉enamelling凡立水varnish叉形顶尖fork centre口罩mask士力;虫漆shellac士巴拿;扳手spanner大芯夹板;宽条芯夹板blockboard; solid corestock-laminated board 大量制造mass production子口刨;槽口刨;边刨rebate plane小型平槽刨miniature router plane小型线料弯曲器small wire bender小型弯折机mini bender小型电路断路器;跳菲miniature circuit breaker (MCB小齿轮pinion山樟San Cheong工件workpiece工字梁I beam工作面working surface工作图;制作图working drawing工作台bench; working table工具tool工具贮存室tool storage工具槽well工具钢tool steel工场workshop工场安全workshop safety工程字书写技巧lettering工程系统engineering system工程绘图engineering drawing工业酒精;火酒methylated spirit弓形手钻;手摇曲柄钻brace弓形手钻嘴brace bit弓锯bow saw; hacksaw弓锯片hacksaw blade弓锯床hacksawing machine四画不平衡imbalance不含铁金属;非铁金属non-ferrous metal 不贯穿孔;闭孔;盲孔blind hole不贯穿鸠尾榫lapped dovetail joint不对称asymmetry不锈钢stainless steel不稳定平衡unstable equilibrium中心centre中心线centre line中心冲centre punch中心钻centre drill中心钻嘴centre bit中央处理器central processing unit (CPU中性neutral中性平衡;随遇平衡neutral equilibrium中性轴neutral axis中密度纤维板medium density fibre board (MDF中粗锉纹second cut中碳钢medium carbon steel中线neutral wire互补金属氧化物半导体complementary metal oxide semiconductors (CMOS 介子;垫片washer介指铁ring mandrel介电常数;电容率permittivity介稳态的;亚稳态的metastable内力internal force内卡尺inside calipers内能internal energy内涵性质intensive properties内圆弯凿scribing gouge内锁式配件interlocking fitting内燃机internal combustion engine 内螺纹制造法tapping内螺丝internal thread内弯边concave edge六角金属枝hexagonal bar六角匙Allen key六角头螺丝hexagonal head screw 公制的;十进制的metric公差tolerance冗余构件redundant member分力component force分子molecule分子力molecular force分切;分割;切断parting off分贝decibel分析analysis分析及批判学analytical and critical studies 分析器analyzer 分流器shunt分界面;界面;接口interface分厘卡micrometer分规divider分割车刀架parting tool holder分解decomposition分压器potential divider; voltage divider隔离开关isolating switch切削工具cutting tool切削液cutting fluid切削深度depth of cut切屑;碎屑chip切线锯法tangential sawing切辊纹;滚纹knurling切断;分切;分割parting off切断工具parting tool勾;勾脚hook勾刀;胶片?刀plastic cutter化胶水tensol反向偏压reverse biased反相放大器inverting amplifier 反相器inverter反射reflection反电动势back e.m.f.反馈;回输feedback天拿水;稀释剂thinner天梯牙;齿条gear rack天然木材natural timber天然干燥法air seasoning孔隙率porosity尺寸dimension尺寸线dimension line尺身blade引力;重力gravitational force心形凸轮heart-shaped cam心材heartwood心轴mandrel心销core pin手工具hand tool手工锯junior hacksaw手削法paring手持虎钳hand vice手柄handle手套gloves手扫漆brushing lacquer手推车barrow手提式竖线锯portable jigsaw手提电动工具portable power tool 手提电钻electric hand drill 手进给hand feed手摇曲柄钻;弓形手钻brace手摇钻hand drill手锉hand file手锯;板锯handsaw手锥bradawl手辘轧机hand rolling machine 支柱;支撑物strut支架;支座support支点fulcrum; pivot文字text方向direction方向针pointing needle方枝square bar方波形square waveform方波产生器squarer方型牙板rectangular die方格纸;网格纸grid paper方通square tube方块图block diagram方锉square file方头钻嘴square shank bit方螺帽square nut方边凿;直边凿firmer chisel木wood木工woodwork木工工作间woodwork area木工工作台woodworker's bench木工车床wood turning lathe; woodworking lathe 木工铅笔carpenter's pencil木工刨床thicknessing and planning machine木牙螺丝;木螺钉wood screw木材timber木材车削wood turning木材车削工具wood turning tools木屑压合板;万花板chipboard木条接榫corner strip joint木圆头槌doming mallet木模;模型patterns木线wood strip木胶粉ureaformal dehyde resin glue木锉rasp木螺钉;木牙螺丝wood screw木槌mallet止推轴承thrust bearing止推垫圈thrust washer比例proportion比例尺scale比例常数proportionality constant比例极限proportional limit比较器comparator比热容量specific heat capacity水平投影面horizontal plane水平仪;平水尺spirit level水气掣;漏电断路掣earth leakage circuit breaker (ELCB 水晶胶;聚酯树脂polyester resin水晶胶的铸造成形resin casting水磨砂纸silicon carbide paper火叉firing fork火水;煤油kerosene火牛;变压器transformer火石轮grinder火花电蚀法;放电极加工electrical discharge machining 火酒;工业酒精methylated spirit火钳tongs火线;活线live wire火砖fire brick爪扣;爪形离合器;犬齿式离合器dog clutch牙板;丝模die牙板扳手;丝模扳手die holder (stock牙板螺帽die nuts牛皮胶;动物胶animal glue牛油纸tracing paper牛顿运动定律Newton's laws of motion犬齿式离合器;爪扣;爪形离合器dog clutch五画丙烯?丁二烯苯乙烯acrylonitrile-butadiene-stryrene (ABS 主轴;心轴spindle主题motif令(纸张的计数单位 ream凹座recess凹模hollowing block凸缘flange凸缘联轴节flange coupling凸轮cam凸轮式配件cam-action fitting凸轮传动cam drive凸头螺丝raised head screw加成作业;添加法addition process加油oiling加速器accelerator功能;用途function功率因子power factor功率放大器power amplifier功率板power amplifier board功率晶体管power transistor包氏记号法Bow's notation「包浩思」;「包豪斯」〈设计风格 Bauhaus半永固法;半永久接合semi-permanent joining 半接榫halving joint半闭式槽榫stopped housing joint半圆(木锉half-round rasp半圆车刀turning gouge半圆锉half-round file半圆头铆钉snap rivet半导体semiconductor卡路里;卡(热量单位 calorie卡纸card paper卡尺;测径器calipers去角;倒角chamfer可切削性machinability可行性feasibility可逆过程reversible process可压缩性compressibility可变电阻variable resistor四分仪quadrant四爪夹头four-jaw independent chuck四圆心法(绘图 four-centre method 外卡尺outside calipers外形塑造shaping外形线;轮廓线outline外推法extrapolation外圆弯凿firmer gouge外螺纹external thread外螺纹制造法threading外弯边convex edge外观appearance失真distortion尼龙;聚醯胺nylon; polyamide (PA 尼龙墨水针笔technical felt-tip pen 左右调校杆lateral adjusting level 市售尺寸;标准尺寸stock size市电频率;电源频率mains frequency平(木锉flat rasp平水尺;水平仪spirit level平行投影parallel projection平行车削parallel turning平行虎钳parallel vice平行钉法parallel nailing平底弯刨flat faced spokeshave平底钻嘴forstner bit平板结构slab construction平流扼流圈;滤波扼流器smoothing choke平流电容器;滤波电容器smoothing capacitor 平流电路;滤汳电路smoothing circuit平面板;正台surface plate平面图;俯视图plan平面锤flatter平移translation平搭榫corner halving joint平嘴钳flat nose pliers平槽刨router plane平衡balance; equilibrium平衡力equilibrant平衡条件equilibrium condition平衡电桥balanced bridge平头弧刀square nose gouge幼纹smooth cut打凹成形hollowing打凸成形raising打槽机routing machine打线;打槽routing打磨fitting; polishing打磨机polisher本生灯Bunsen burner本征半导体intrinsic semiconductor 正反器;触发器;复振器flip-flop 正反馈;正回输positive feedback 正火normalizing正向偏置forward bias正投影orthographic projection正投影图orthographic drawing正弦波形sinusoidal waveform正面投影front projection正视图elevation; front elevation正极;阳极anode正齿轮spur gear正台;平面板surface plate永久性接合permanent joining瓦通纸;瓦楞纸板corrugated board 生长层cambium layer 生产图production drawing生胶浆rubber cement生钢;铸钢cast steel生铁;铸铁cast iron用途;功能function白杨木poplar白胶浆PVA glue; white glue皮沙垫leather sandbag皮革leather皮革黏合剂leather glue皮鞋leather shoes目录contents矢量;向量vector石灰岩limestone石英晶体振荡器quartz crystal oscillator石棉asbestos; asbestus石膏Plaster of Paris示波器oscilloscope立体图pictorial drawing六画交流电流alternating current (a.c.交流电压 a.c. voltage交联结构cross-linked structure仿饰金gilding metal伏特volt光力架clear lacquer光拉软钢bright drawn mild steel (B.D.M.S. 光敏电阻light dependent resistor (LDR光测弹性学photoelasticity光刨;滑刨smoothing plane光电效应photoelectric effect光泽lustre全闭式槽榫closed housing joint共面力coplanar force共聚合作用co-polymerization共聚物copolymer共价键covalent bond共振;共鸣;谐振resonance印刷电路板printed circuit board (PCB 同素异形allotropy同轴电缆coaxial cable同温equality of temperature向量;矢量vector向量和vector sum104合力resultant force合口扁钳close mouth tongs合成色;等和色secondary colour合成品composite合成粅料composite material合金alloy合金工具钢alloy tool steel合钉;定位销dowel回火tempering回复力restoring force回复力偶restoring couple回弹resilience回输;反馈feedback地线earth wire多刃切削刀具multi-point cutter 多孔塑料;泡沫塑料;海绵状塑料foam plastics 多方榫接合pinned joint多媒体multi-media多晶性polycrystallinity多谐振动器;多谐振荡器multivibrator多边形力学;力多边形polygon of force字母冲letter punch字板letter stencil安全safety安全守则safety rule安全系数safety factor安全措施safety precaution105安全眼罩safety goggle安全设备safety equipment安全药箱safety box安培ampere安培计;电流表ammeter尖脚spur年轮annual ring成本cost成形forming扣件;击固件fastener扣钉clout nail; cramp托架bracket收缩shrinkage曲柄crank曲柄轴crank shaft曲线规;云板;云尺French curve 有效的efficient有效电流effective current灰;灰末ash百折胶;百折胶;聚丙烯polypropylene (PP 竹bamboo羊角锤claw hammer老化ageing肋条rib肌理;质感;质地texture自由度degree of freedom自动控制automatic control106自动进给auto-feed自然干燥法natural seasoning自感量self-inductance自感应self-induction色彩;颜色colour色调tone色环colour wheel行星齿轮;周转齿轮epicyclic gear七画肘节开关toggle-switch串激电动机;串绕电动机series-wound motor 位能;势能potential energy 位梯度;势梯度potential gradient位移displacement位错dislocation伸长度elongation作工硬化work hardening作功work done作图线construction line低密聚乙烯low density polyethylene (LDPE低通滤波器low-pass filter低电压low voltage低碳钢low carbon steel布置layout免油轴承oil-less bearing冷加工;冷作工cold working冷加工硬化cold work hardening冷色cool colour冷轧压cold rolling冷却系统cooling system冷却效应cooling effect冷却液流量coolant rate冷凝胶;环氧树脂epoxy resin108利口;「披」口;铁屑burr刨平planing刨花板;碎料板particle board吹风机air blower吹气模塑;吹模塑blow moulding吹管blow pipe含铁金属ferrous metal含水量moisture content坑凿cross-cut chisel均方根值root mean square value均角投影图;等角投影图isometric drawing 均速圆周运动uniform circular motion 夹;夹钳clamp夹cramp夹卡mounting board夹具fixture; jig夹具及固定装置jig and fixture夹板;胶合板plywood夹持工具clamping device; holding tool 夹背锯;榫锯tenon saw夹头chuck夹头开启匙;夹头扳手chuck key夹叠黏合成形lamination尾座tailstock床身;床道lathe bed床鞍;刀座帷apron形心;面心centroid109形状shape形变deformation「快把」板;硬质纤维板hardboard快速移位rapid traverse抗扭强度torsional strength抗屈强度bending strength; yield strength抗性分量;无功分量reactive component抗拉强度tensile strength抗氧化剂anti-oxidant抗剪强度shearing strength 抗磁性物料diamagnetic material 抗挠性stiffness抗压强度compressive strength抗断强度breaking strength技术员;技师technician扶架steady扭力torsion扭矩;转矩torque扭转torsion扭转角angle of torsion把手hand grip扼流圈choke扳手spanner; wrench投影projection投影面projection plane投影线projection line攻丝tap材料material材料单;材料表material list杜拉铝duralumin杉木spruce步进电动机stepper motor步冲轮廓法nibbling每分钟转数revolution per minute (r.p.m. 系统组件system component角托架angle bracket角位移angular displacement角板;直角板angle plate角度angle角榫corner angle joint; corner joint角铁angle iron谷巴凡立水cobal varnish车刀架tool holder车床lathe车床工具lathe tools车床中心钻咀lathe centre bit车床操作法lathe operation车削;车旋lathe turning; turning车削工具turning tools防火胶板Formica防锈rust prevention防声耳筒;护耳器ear-protector防松螺帽lock nut防护装置;保护罩;保护网guard; safety guard 八画注射成形法;喷射铸造法injection moulding并激电动机;并绕电动机shunt-wound motor 乳酪胶casein glue乳胶漆emulsion paint亚加力;压克力;聚甲基丙烯酸甲脂acrylics; polymethyl methacrylate (PMMA 亚稳态的;介稳态的metastable来回摆动oscillating两点透视two-point perspective刻度;划线ruling刺冲dot punch刮刀scraper刮擦scraping制动鼓drum brake制动碟disc brake制动器brake受迫振动forced vibration受迫振荡forced oscillation和谐harmony周转齿轮;行星齿轮epicyclic gear 固定夹;台夹bench holdfast固定负载dead load定子stator定位销;合钉dowel定位螺丝set screw定距轮stitch marker屈片机folding machine屈曲bending屈服点;降服点yield point屈圈法loop forming屈卷法scrolling屈接缝folded lap seam屈喉机tube bender屈折folding屈折线folding line屈压接缝folded & grooved seam延性ductility延性的ductile弦锯法plain sawing弧口凿;圆凿gouge往复式运动reciprocatory motion拉力tensile force拉力计;张力计tensiometer; tensometer拉钉blind rivet; pop rivet拉钉接合blind riveting; pop riveting拉钉钳blind riveting pliers; pop riveting pliers 拉张tension拉张应力tensile stress拉张应变tensile strain拉细drawing-down拉制法drawing拉线wire drawing「披」口;利口;铁屑burr拔钳nippers拋光buffing拋光机buffing machine放大;扩大enlargement放大尺pantograph放大倍数amplification factor放大器amplifier放电极加工;火花电蚀法electrical discharge machining 易用万能尺line setter 易碎fragile〈绘画的〉明暗运用;描影shading枝;杆rod杯形顶尖cup centre杯头螺丝hexagonal socket head cap screw板锯panel saw松木pine松节水turpentine法式磨光French polishing法拉〈电容量单位〉farad油石;磨刀石oil stone油漆;涂料paint泡沫塑料;多孔塑料;海绵状塑料foam plastics 物理特性physical property物理属性physical attribute物理量physical quantity盲孔;闭孔;不贯穿孔blind hole直尺ruler; straight rule直角叉榫corner bridle joint直角尺try square直角板;角板angle plate直角杠杆bell crank lever直身钻嘴straight shank drill直车刀架straight tool holder直流发电机 d.c. generator直流电流direct current (d.c.直流电动机;直流马达 d.c. motor 直纹锯rip saw直线切削linear interpolation直线运动rectilinear motion直边凿;方边凿firmer chisel直铁剪straight snips硅silicon空行程idle stroke空气动力学aerodynamics空间space空载no load花纹凿embossing stamp花梨木rosewood花样;图案pattern虎克定律Hooke's Law虎钳vice虎钳护罩vice clamp初步意念proposed solution表面surface表面展开图surface development表面张力surface tension表面处理surface finishing; surface treatment表面硬化case hardening表面硬化钢case-hardened steel表达方式presentation表达技巧;传意技巧communication technique 表观膨胀;视膨胀apparent expansion金工metalwork金工工作间metalwork area金工角尺engineering square金工车床metalwork lathe金工虎钳engineer's vice金工锯床power hacksaw金属包头;金属箍ferrule金属配件metal fittings金属线wire金属压展机hand rolling mill金属擦光剂;磨光剂metal polish金属薄片sheet metal金属键metallic bond长方通rectangular tube长刨trying plane长螺旋钻咀long auger bit长镗孔long boring闸极gate阻抗impedance附件attachment附录appendices青铜bronze非反相放大器non-inverting amplifier非本征半导体extrinsic semiconductor非破坏性试验non-destructive testing非晶状固体amorphous solid非顽磁性铁磁材料non-retentive ferromagnetic material 非压缩性流体incompressible fluid非稳态unsteady state非铁金属;不含铁金属non-ferrous metal九画亮漆;力架lacquer信号signal信号产生机signal generator信号处理signal processing保养;维修maintenance保险丝fuse保护罩;保护网;防护装置guard; safety guard 促凝剂accelerator削屑swarf垂直投影面vertical plane型砧swages〈书的〉封皮binding封面cover急回机构quick return mechanism扁枝bar扁头cross-pein扁头法upsetting扁头铆钉flat head rivet 扁头螺丝flat head screw 扁凿flat chisel指示器indicator指形榫finger joint施力effort染色staining染色剂stain架构framework柄stock柚木teak柳安木lauan流程图flow chart洗漆水paint remover活塞piston活塞销gudgeon pin活线;火线live wire炮铜gun metal玻璃砂纸glass paper玻璃胶silicon sealant玻璃纤维glass fibre玻璃纤维席glass fibre mats界面;分界面;接口interface相差phase difference相对密度relative density砂布emery cloth砂磨sanding砂磨纸abrasive paper砂磨机sander砂铸;砂铸模sand casting研究探讨research研磨;磨削grinding研磨角grinding angle科技technology科技研习technological studies 科学知识scientific knowledge科学瓷;聚氰胺毋醛树脂melamine-formaldehyde resin (MF 红铜垫圈copper washer美学aesthetics耐火胶板fire-resisted laminate耐火砖refractory block耐冲击聚苯乙烯high impact polystyrene背back胡桃木walnut范德华引力Van der Waals force英制惠氏标准螺纹British Standard Whitworth thread (B.S.W. 苯乙烯丙烯?共聚物styrene-acrylonitrile copolymer苯酚甲醛phenol formaldehyde (PF计;规gauge定时器timer计划planning计算器;计算机computer计算器辅助工程computer-aided engineering (CAE计算器辅助控制computer-aided control计算器辅助设计computer-aided design (CAD计算器辅助制造computer-aided manufacturing (CAM 计算器数控computer numerical control (CNC负反馈;负回输negative feedback负极;阴极cathode负载load轨路式砂纸磨机orbital sander重力;引力gravitational force重心centre of gravity重量weight重锉法heavy filing限制开关;极限掣limit switch限流器current restrictor降服点;屈服点yield point降压器step down transformer面plane面心;形心centroid面材plane materiel面板face plate面板车削法face plate turning面结型晶体管junction transistor面罩face mask音量volume页边margin风车锯;圆盘锯circular saw风格style风煤炉forging hearth飞轮flywheel飞机木;菠萨轻木balsa首版;原型;雏形prototype恒温器;温度调节器thermostat十画俯视图;平面图plan倒角;去角chamfer倒模成形;模塑;铸模成形moulding 修边trimming修边机trimmer剖切面cutting plane剖切面线cutting plane line剖面;纵切面section剖视图sectional view剖线hatching line刚性;刚度rigidity刚性模量;刚性模数modulus of rigidity刚强度;硬挺度stiffness刚体rigid body原子粒;晶体管transistor原色primary colour原型;雏形;首版prototype原料raw material哥罗芳;三氯甲烷chloroform埋头直孔counterbore埋头铆钉countersink head rivet埋头锥孔countersink埋头螺栓countersink head bolt埋头螺丝countersink head screw埋头钻countersink drill埋头钻嘴countersink bit; rose countersink drill套筒;套管sleeve套锤fullers家用的domestic展性malleability展性的malleable展开图development峰至峰值peak-to-peak value峰值peak value差动放大器;微分放大器differential amplifier 徒手草图freehand sketch 径线锯法radial sawing径锯法quarter sawing振动vibration振幅amplitude振荡oscillating振荡运动oscillatory motion振荡器oscillator效率efficiency时效硬化age hardening时间常数time constant框架frame气动的系统;气压的系统pneumatic system气动控制pneumatic control气阀gas valve气焊gas welding空气压缩air compression氧乙炔焊接oxy-acetylene welding氧化oxidation; oxidize消失点vanishing point消色差achromatic colour浸涂dip coating海绵状塑料;泡沫塑料;多孔塑料foam plastics 浮力buoyancy 浮雕relief特性property珠光体pearlite疲劳fatigue真空成形;真空吸塑vacuum forming真空成形机vacuum former真空吸塑成形法vacuum moulding真实形状true shape矩波形rectangular waveform纹理grain级联系统cascade system纸板carton board脆弱的;易碎的brittle脆性brittleness脉冲pulse能量守恒conservation of energy能量守恒定律law of conservation of energy 草图sketch草图画纸layout paper草稿draft衰减attenuation起化magnetization起泡剂;发泡剂foaming agent起动扭矩starting torque起动器starter起磁;磁化magnetization退化degradation退火annealing配件fitting钉合nailing钉钳;铁钳pincers钉冲nail punch钉锤cross-pein hammer针尖point针叶needle-point leaf针叶树coniferous tree针锉;杂锦锉needle files马氏体martensite马达;电动机;摩打motor马粪纸straw board骨架结构carcase construction容差;宽裕度allowance高密度聚乙烯high density polyethylene (HDPE 高通滤波器high-pass filter高速钢high speed steel高电压high voltage高碳钢high carbon steel十一画干燥法;干材法seasoning偶合;耦合(电工 coupling侧面投影side projection侧条芯夹板laminboard侧视图;端视图end elevation; end view 偏心凸轮eccentric cam偏向bias; deviation偏差deviation偏压bias偏离drift剪刀scissors剪力shearing force剪切shear剪床;闸床guillotine对角剪钳diagonal cutting pliers。
机械专业中英文对照翻译大全171页word
机械专业英语词汇中英文对照翻译一览表陶瓷 ceramics合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion车架 automotive chassis悬架 suspension转向器 redirector变速器 speed changer板料冲压 sheet metal parts孔加工 spot facing machining车间 workshop工程技术人员 engineer气动夹紧 pneuma lock数学模型 mathematical model画法几何 descriptive geometry机械制图 Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求 technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear直齿锥齿轮 straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams共轭曲线 conjugate curve范成法 generation method定义域 definitional domain值域 range导数\\微分 differential coefficient求导 derivation定积分 definite integral不定积分 indefinite integral曲率 curvature偏微分 partial differential毛坯 rough游标卡尺 slide caliper千分尺 micrometer calipers攻丝 tap二阶行列式 second order determinant 逆矩阵 inverse matrix线性方程组 linear equations概率 probability随机变量 random variable排列组合 permutation and combination 气体状态方程 equation of state of gas动能 kinetic energy势能 potential energy机械能守恒 conservation of mechanical energy动量 momentum桁架 truss轴线 axes余子式 cofactor逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构 fluid drive mechanism机械零件 mechanical parts淬火冷却 quench淬火 hardening回火 tempering调质 hardening and tempering磨粒 abrasive grain结合剂 bonding agent砂轮 grinding wheel后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe钻削镗削 bore车削 turning磨床 grinder基准 benchmark钳工 locksmith锻 forge压模 stamping焊 weld拉床 broaching machine拉孔 broaching装配 assembling铸造 found流体动力学 fluid dynamics流体力学 fluid mechanics加工 machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration气压 air pressure pneumatic pressure稳定性 stability介质 medium液压驱动泵 fluid clutch液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability随机信号 random signal离散信号 discrete signal超声传感器 ultrasonic sensor 集成电路 integrate circuit 挡板 orifice plate残余应力 residual stress套筒 sleeve扭力 torsion冷加工 cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加工 hotwork摄像头 CCD camera倒角 rounding chamfer优化设计 optimal design工业造型设计 industrial moulding design有限元 finite element滚齿 hobbing插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器 Programmable Logic Controller PLC 电火花加工 electric spark machining电火花线切割加工 electrical discharge wire - cutting相图 phase diagram热处理 heat treatment固态相变 solid state phase changes有色金属 nonferrous metal陶瓷 ceramics合成纤维 synthetic fibre电化学腐蚀 electrochemical corrosion车架 automotive chassis悬架 suspension转向器 redirector变速器 speed changer板料冲压 sheet metal parts孔加工 spot facing machining车间 workshop工程技术人员 engineer气动夹紧 pneuma lock数学模型 mathematical model画法几何 descriptive geometry机械制图 Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求 technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear直齿锥齿轮 straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams共轭曲线 conjugate curve范成法 generation method定义域 definitional domain值域 range导数\\微分 differential coefficient 求导 derivation定积分 definite integral不定积分 indefinite integral曲率 curvature偏微分 partial differential毛坯 rough游标卡尺 slide caliper千分尺 micrometer calipers攻丝 tap二阶行列式 second order determinant 逆矩阵 inverse matrix线性方程组 linear equations概率 probability随机变量 random variable排列组合 permutation and combination气体状态方程 equation of state of gas动能 kinetic energy势能 potential energy机械能守恒 conservation of mechanical energy 动量 momentum桁架 truss轴线 axes余子式 cofactor逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构 fluid drive mechanism机械零件 mechanical parts淬火冷却 quench淬火 hardening回火 tempering调质 hardening and tempering磨粒 abrasive grain结合剂 bonding agent砂轮 grinding wheel Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表 notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传 rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车 mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆 Archimedes worm安全系数 safety factor; factor of safety安全载荷 safe load凹面、凹度 concavity扳手 wrench板簧 flat leaf spring半圆键 woodruff key变形 deformation摆杆 oscillating bar摆动从动件 oscillating follower摆动从动件凸轮机构 cam with oscillating follower 摆动导杆机构 oscillating guide-bar mechanism摆线齿轮 cycloidal gear摆线齿形 cycloidal tooth profile摆线运动规律 cycloidal motion摆线针轮 cycloidal-pin wheel包角 angle of contact保持架 cage背对背安装 back-to-back arrangement背锥 back cone ； normal cone背锥角 back angle背锥距 back cone distance比例尺 scale比热容 specific heat capacity闭式链 closed kinematic chain闭链机构 closed chain mechanism臂部 arm变频器 frequency converters变频调速 frequency control of motor speed变速 speed change变速齿轮 change gear change wheel变位齿轮 modified gear变位系数 modification coefficient标准齿轮 standard gear标准直齿轮 standard spur gear表面质量系数 superficial mass factor表面传热系数 surface coefficient of heat transfer表面粗糙度 surface roughness并联式组合 combination in parallel并联机构 parallel mechanism并联组合机构 parallel combined mechanism 并行工程 concurrent engineering并行设计 concurred design, CD不平衡相位 phase angle of unbalance不平衡 imbalance (or unbalance)不平衡量 amount of unbalance不完全齿轮机构 intermittent gearing波发生器 wave generator波数 number of waves补偿 compensation参数化设计 parameterization design, PD残余应力 residual stress操纵及控制装置 operation control device槽轮 Geneva wheel槽轮机构 Geneva mechanism ； Maltese cross 槽数 Geneva numerate槽凸轮 groove cam侧隙 backlash差动轮系 differential gear train差动螺旋机构 differential screw mechanism差速器 differential常用机构 conventional mechanism; mechanism in common use 车床 lathe承载量系数 bearing capacity factor承载能力 bearing capacity成对安装 paired mounting尺寸系列 dimension series齿槽 tooth space齿槽宽 spacewidth齿侧间隙 backlash齿顶高 addendum齿顶圆 addendum circle齿根高 dedendum齿根圆 dedendum circle齿厚 tooth thickness齿距 circular pitch齿宽 face width齿廓 tooth profile齿廓曲线 tooth curve齿轮 gear齿轮变速箱 speed-changing gear boxes齿轮齿条机构 pinion and rack齿轮插刀 pinion cutter; pinion-shaped shaper cutter 齿轮滚刀 hob ,hobbing cutter齿轮机构 gear齿轮轮坯 blank齿轮传动系 pinion unit齿轮联轴器 gear coupling齿条传动 rack gear齿数 tooth number齿数比 gear ratio齿条 rack齿条插刀 rack cutter; rack-shaped shaper cutter齿形链、无声链 silent chain齿形系数 form factor齿式棘轮机构 tooth ratchet mechanism插齿机 gear shaper重合点 coincident points重合度 contact ratio冲床 punch传动比 transmission ratio, speed ratio传动装置 gearing; transmission gear传动系统 driven system传动角 transmission angle传动轴 transmission shaft串联式组合 combination in series串联式组合机构 series combined mechanism 串级调速 cascade speed control创新 innovation creation创新设计 creation design垂直载荷、法向载荷 normal load唇形橡胶密封 lip rubber seal磁流体轴承 magnetic fluid bearing从动带轮 driven pulley从动件 driven link, follower从动件平底宽度 width of flat-face从动件停歇 follower dwell从动件运动规律 follower motion从动轮 driven gear粗线 bold line粗牙螺纹 coarse thread大齿轮 gear wheel打包机 packer打滑 slipping带传动 belt driving带轮 belt pulley带式制动器 band brake单列轴承 single row bearing单向推力轴承 single-direction thrust bearing单万向联轴节 single universal joint单位矢量 unit vector当量齿轮 equivalent spur gear; virtual gear当量齿数 equivalent teeth number; virtual number of teeth当量摩擦系数 equivalent coefficient of friction当量载荷 equivalent load刀具 cutter导数 derivative倒角 chamfer导热性 conduction of heat导程 lead导程角 lead angle等加等减速运动规律 parabolic motion; constant acceleration and deceleration motion等速运动规律 uniform motion; constant velocity motion等径凸轮 conjugate yoke radial cam等宽凸轮 constant-breadth cam等效构件 equivalent link等效力 equivalent force等效力矩 equivalent moment of force等效量 equivalent等效质量 equivalent mass等效转动惯量 equivalent moment of inertia等效动力学模型 dynamically equivalent model底座 chassis低副 lower pair点划线 chain dotted line（疲劳）点蚀 pitting垫圈 gasket垫片密封 gasket seal碟形弹簧 belleville spring顶隙 bottom clearance定轴轮系 ordinary gear train; gear train with fixed axes 动力学 dynamics动密封 kinematical seal动能 dynamic energy动力粘度 dynamic viscosity动力润滑 dynamic lubrication动平衡 dynamic balance动平衡机 dynamic balancing machine动态特性 dynamic characteristics动态分析设计 dynamic analysis design动压力 dynamic reaction动载荷 dynamic load端面 transverse plane端面参数 transverse parameters端面齿距 transverse circular pitch端面齿廓 transverse tooth profile端面重合度 transverse contact ratio端面模数 transverse module端面压力角 transverse pressure angle锻造 forge对称循环应力 symmetry circulating stress对心滚子从动件 radial (or in-line ) roller follower对心直动从动件 radial (or in-line ) translating follower对心移动从动件 radial reciprocating follower对心曲柄滑块机构 in-line slider-crank (or crank-slider) mechanism 多列轴承 multi-row bearing多楔带 poly V-belt多项式运动规律 polynomial motion多质量转子 rotor with several masses惰轮 idle gear额定寿命 rating life额定载荷 load ratingII 级杆组 dyad发生线 generating line发生面 generating plane法面 normal plane法面参数 normal parameters法面齿距 normal circular pitch法面模数 normal module法面压力角 normal pressure angle法向齿距 normal pitch法向齿廓 normal tooth profile法向直廓蜗杆 straight sided normal worm法向力 normal force反馈式组合 feedback combining反向运动学 inverse ( or backward) kinematics 反转法 kinematic inversion反正切 Arctan范成法 generating cutting仿形法 form cutting方案设计、概念设计 concept design, CD防振装置 shockproof device飞轮 flywheel飞轮矩 moment of flywheel非标准齿轮 nonstandard gear非接触式密封 non-contact seal非周期性速度波动 aperiodic speed fluctuation非圆齿轮 non-circular gear粉末合金 powder metallurgy分度线 reference line; standard pitch line分度圆 reference circle; standard (cutting) pitch circle 分度圆柱导程角 lead angle at reference cylinder分度圆柱螺旋角 helix angle at reference cylinder分母 denominator分子 numerator分度圆锥 reference cone; standard pitch cone分析法 analytical method封闭差动轮系 planetary differential复合铰链 compound hinge复合式组合 compound combining复合轮系 compound (or combined) gear train复合平带 compound flat belt复合应力 combined stress复式螺旋机构 Compound screw mechanism杆组 Assur group干涉 interference刚度系数 stiffness coefficient刚轮 rigid circular spline钢丝软轴 wire soft shaft刚体导引机构 body guidance mechanism 刚性冲击 rigid impulse (shock)刚性转子 rigid rotor刚性轴承 rigid bearing刚性联轴器 rigid coupling高度系列 height series高速带 high speed belt高副 higher pair格拉晓夫定理 Grashoff`s law根切 undercutting公称直径 nominal diameter高度系列 height series功 work工况系数 application factor工艺设计 technological design工作循环图 working cycle diagram工作载荷 external loads工作空间 working space工作应力 working stress工作阻力 effective resistance工作阻力矩 effective resistance moment公法线 common normal line公共约束 general constraint公制齿轮 metric gears功率 power功能分析设计 function analyses design共轭齿廓 conjugate profiles共轭凸轮 conjugate cam构件 link鼓风机 blower固定构件 fixed link; frame固体润滑剂 solid lubricant关节型操作器 jointed manipulator惯性力 inertia force惯性力矩 moment of inertia ,shaking moment 惯性力平衡 balance of shaking force惯性力完全平衡 full balance of shaking force惯性力部分平衡 partial balance of shaking force 惯性主矩 resultant moment of inertia惯性主失 resultant vector of inertia冠轮 crown gear广义机构 generation mechanism广义坐标 generalized coordinate轨迹生成 path generation轨迹发生器 path generator滚刀 hob滚道 raceway滚动体 rolling element滚动轴承 rolling bearing滚动轴承代号 rolling bearing identification code 滚针 needle roller滚针轴承 needle roller bearing滚子 roller滚子轴承 roller bearing滚子半径 radius of roller滚子从动件 roller follower滚子链 roller chain滚子链联轴器 double roller chain coupling滚珠丝杆 ball screw滚柱式单向超越离合器 roller clutch 过度切割 undercutting函数发生器 function generator函数生成 function generation含油轴承 oil bearing耗油量 oil consumption耗油量系数 oil consumption factor 赫兹公式 H. Hertz equation合成弯矩 resultant bending moment 合力 resultant force合力矩 resultant moment of force 黑箱 black box横坐标 abscissa互换性齿轮 interchangeable gears 花键 spline滑键、导键 feather key滑动轴承 sliding bearing滑动率 sliding ratio滑块 slider环面蜗杆 toroid helicoids worm环形弹簧 annular spring缓冲装置 shocks; shock-absorber灰铸铁 grey cast iron回程 return回转体平衡 balance of rotors混合轮系 compound gear train积分 integrate机电一体化系统设计mechanical-electrical integration system design机构 mechanism机构分析 analysis of mechanism机构平衡 balance of mechanism机构学 mechanism机构运动设计 kinematic design of mechanism机构运动简图 kinematic sketch of mechanism机构综合 synthesis of mechanism机构组成 constitution of mechanism机架 frame, fixed link机架变换 kinematic inversion机器 machine机器人 robot机器人操作器 manipulator机器人学 robotics技术过程 technique process技术经济评价 technical and economic evaluation技术系统 technique system机械 machinery机械创新设计 mechanical creation design, MCD机械系统设计 mechanical system design, MSD机械动力分析 dynamic analysis of machinery机械动力设计 dynamic design of machinery机械动力学 dynamics of machinery机械的现代设计 modern machine design机械系统 mechanical system机械利益 mechanical advantage机械平衡 balance of machinery机械手 manipulator机械设计 machine design; mechanical design机械特性 mechanical behavior机械调速 mechanical speed governors机械效率 mechanical efficiency机械原理 theory of machines and mechanisms机械运转不均匀系数 coefficient of speed fluctuation 机械无级变速 mechanical stepless speed changes基础机构 fundamental mechanism基本额定寿命 basic rating life基于实例设计 case-based design,CBD基圆 base circle基圆半径 radius of base circle基圆齿距 base pitch基圆压力角 pressure angle of base circle基圆柱 base cylinder基圆锥 base cone急回机构 quick-return mechanism急回特性 quick-return characteristics急回系数 advance-to return-time ratio急回运动 quick-return motion棘轮 ratchet棘轮机构 ratchet mechanism棘爪 pawl极限位置 extreme (or limiting) position极位夹角 crank angle between extreme (or limiting) positions计算机辅助设计 computer aided design, CAD计算机辅助制造 computer aided manufacturing, CAM计算机集成制造系统 computer integrated manufacturing system, CIMS 计算力矩 factored moment; calculation moment计算弯矩 calculated bending moment加权系数 weighting efficient加速度 acceleration加速度分析 acceleration analysis加速度曲线 acceleration diagram尖点 pointing; cusp尖底从动件 knife-edge follower间隙 backlash间歇运动机构 intermittent motion mechanism 减速比 reduction ratio减速齿轮、减速装置 reduction gear减速器 speed reducer减摩性 anti-friction quality渐开螺旋面 involute helicoid渐开线 involute渐开线齿廓 involute profile渐开线齿轮 involute gear渐开线发生线 generating line of involute 渐开线方程 involute equation渐开线函数 involute function渐开线蜗杆 involute worm渐开线压力角 pressure angle of involute渐开线花键 involute spline简谐运动 simple harmonic motion键 key键槽 keyway交变应力 repeated stress交变载荷 repeated fluctuating load交叉带传动 cross-belt drive交错轴斜齿轮 crossed helical gears胶合 scoring角加速度 angular acceleration角速度 angular velocity角速比 angular velocity ratio角接触球轴承 angular contact ball bearing角接触推力轴承 angular contact thrust bearing 角接触向心轴承 angular contact radial bearing 角接触轴承 angular contact bearing铰链、枢纽 hinge校正平面 correcting plane接触应力 contact stress接触式密封 contact seal阶梯轴 multi-diameter shaft结构 structure结构设计 structural design截面 section节点 pitch point节距 circular pitch; pitch of teeth节线 pitch line节圆 pitch circle节圆齿厚 thickness on pitch circle节圆直径 pitch diameter节圆锥 pitch cone节圆锥角 pitch cone angle解析设计 analytical design紧边 tight-side紧固件 fastener径节 diametral pitch径向 radial direction径向当量动载荷 dynamic equivalent radial load径向当量静载荷 static equivalent radial load径向基本额定动载荷 basic dynamic radial load rating 径向基本额定静载荷 basic static radial load tating 径向接触轴承 radial contact bearing径向平面 radial plane径向游隙 radial internal clearance径向载荷 radial load径向载荷系数 radial load factor径向间隙 clearance静力 static force静平衡 static balance静载荷 static load静密封 static seal局部自由度 passive degree of freedom矩阵 matrix矩形螺纹 square threaded form锯齿形螺纹 buttress thread form矩形牙嵌式离合器 square-jaw positive-contact clutch 绝对尺寸系数 absolute dimensional factor绝对运动 absolute motion绝对速度 absolute velocity均衡装置 load balancing mechanism抗压强度 compression strength开口传动 open-belt drive开式链 open kinematic chain开链机构 open chain mechanism可靠度 degree of reliability可靠性 reliability可靠性设计 reliability design, RD空气弹簧 air spring空间机构 spatial mechanism空间连杆机构 spatial linkage空间凸轮机构 spatial cam空间运动副 spatial kinematic pair空间运动链 spatial kinematic chain空转 idle宽度系列 width series框图 block diagram雷诺方程Reynolds‘s equation离心力 centrifugal force离心应力 centrifugal stress离合器 clutch离心密封 centrifugal seal理论廓线 pitch curve理论啮合线 theoretical line of action隶属度 membership力 force力多边形 force polygon力封闭型凸轮机构 force-drive (or force-closed) cam mechanism 力矩 moment力平衡 equilibrium力偶 couple力偶矩 moment of couple连杆 connecting rod, coupler连杆机构 linkage连杆曲线 coupler-curve连心线 line of centers链 chain链传动装置 chain gearing链轮 sprocket sprocket-wheel sprocket gear chain wheel 联组 V 带 tight-up V belt联轴器 coupling shaft coupling两维凸轮 two-dimensional cam临界转速 critical speed六杆机构 six-bar linkage龙门刨床 double Haas planer轮坯 blank轮系 gear train螺杆 screw螺距 thread pitch螺母 screw nut螺旋锥齿轮 helical bevel gear螺钉 screws螺栓 bolts。
机械类专业词汇中英文对照翻译表大全
专业机械用语中英文对照共43页
机械专业英语词汇陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing 滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting 相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth 当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity 动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series 功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine 机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane 接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank 轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile 十字滑块联轴器double slider coupling; Oldham‘s coupling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint 双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing。
(完整版)机械专业相关词汇中英文翻译大全
机械专业相关词汇中英文翻译大全单价unit price工日合计Man-day total/work-day total人工费cost of labor材料费materials expenses机械的mechanical检查接线connection test发电机generator调相机phase regulator周波cycle减负荷装置 load-shedding equipment断路器柜circuit breaker cabinet单母线single busbar互感器transformer每相电流Current by Phase封闭式插接close type socket joint发电机控制面板generator control panel分级卸载sorted unloading同步控制synchronization control调速器 speed governor信号屏signal screen继电器relay高压柜high pressure cabinet油浸电力变压器oil-immersed power transformer空气断路器air circuit breaker控制屏control panel直流馈电屏direct current feed control panel电容器electric condenser计量盘metering panel成套配电箱whole set of distribution box落地式floor model控制开关Control switches铜芯电力电缆Copper core power cable控制电缆actuating cable热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing万用槽钢versatile U-steel电缆托架 cable bracket钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座防爆插座Explosion-proof socket接地绞线earthing twisted pair接地母线 earthing bus接地极 lightning conductor硬质聚氯乙烯管rigid polyvinyl chloride pipe航空集散站air terminal水银灯具Mercury Lamp金属卤化物灯metal halide lamp高压钠灯High Pressure Sodium Lamp额定电压Rated Voltage额定功率Rated Power光源 Light Source防护等级Grade of Protection高压汞灯High Pressure Mercury Lamp高压钠灯High Pressure Sodium Lamp金属卤化物灯Metallic Halide Lamp照明电缆 lighting cable单线mongline穿线threading接地跨接线 earthing jumper分线箱junction box接线盒connection box圆钢round steel扁钢flat steel插座socket配电盘switchboard转换开关alternation switch自动指令呼叫装置automatic instruction calling device 扬声器loudspeaker明装Unfold Install暗装Conceal Install感温探测器Thermal Detector转台造型机turntable molding machine气动震实造型机air jarring moulding machine有箱造型机box molding machine压铸机die casting machine热室压铸机hot-chamber die casting machine 惯性落砂机inertia knock-out grid浇包ladle浇注机cating machine冲天炉cupola (cupola furnace)水冷冲天炉water cooled cupola焦碳炉coke-fired furnace退火炉annealing oven回火炉drawing furnace喷丸机high pressure blasting machine抛砂机sand throwing machine摆轮式混砂机speedmuller自动分箱机automatic box splitter自动合箱机automatic closer自动壳型机autoclino风动工具air tool锻造forging无型锻造open forging水压机锻造hydraulic forging机器锻造machine forging自由锻造flat-die forging多型槽锻造multiple impression forging冷锻cold forging锤锻（自由锻）hammer forging平锻horzontal forging镦锻upset forging辊锻roll forging模锻die forging热模锻pressure forging开式模锻open-die forging精密模锻prescision drop forging挤压模锻no-draft forging冷拉cold draw热拉hot draw冷挤压cold extruding切边trim冷切边cold trim热切边hot trim冲孔punching校正straightening板料冲压sheet stamping制坯blank锻造毛坯forging blank上模upper die下模bottom die(counter die)上锤头top swage下锤头lower die汽锤steam hammer无砧坐模锻锤forging hammer without anvilbed摩擦锤jump hammer落锤block hammer水平分模（平锻机）horizontal parting冷锻模cold forging die型锻模forging die精整模forming die顶锻模joggling die锻压机forging die水压机water press平锻机horizontal forging machine汽力锻压机steam power forging press 压弯机bending press模锻压力机drop press曲轴压力机crank press曲柄压力机knuckle-joint press切边压力机trimming press切断压力机cutting-out press精压机coining press辊锻机forging roll镦锻机upsetting forging press喷丸清理sand blast cleaning消除内应力residual stress relieving 水力清理hydraulic blasting酸洗pickling超声波清洗ultrasonic cleaning超声波探伤ultrasonic inspection冲压stamping冲压下料bar stock cutting by punching 冲压线press line凸模punch凸凹模punch-die冲孔模piercing die修边模trimming die预弯模die for first-forming扭弯模twisting die扭弯模twisting die扭弯成形模twisting-forming die 压弯模bending die压弯翻边模bending-flanging die 压扁模flattening die压圆模circular bending die 压弯卷圆模bending-curling die 压弯压筋模bending-beading die 落料模blanking die落料压印模blanking-coining die 落料切槽模blanking-slotting die缩口模neckling die翻孔整形模hole flanging-sizing die 翻边成形模flanging forming die切槽模slotting die拉延模drawing die下料stock cutting开卷unreel成形forming翻边flanging反向拉伸reverse-draw整形restricking整径trued切口cut-off (shear-out) 切边trimming压扁flattening应变strain压痕impression拉延drawing拉伸deep drawng挤压extrusion滚挤roll-forming卷边折边edging刮边scraping三室清洗机three-stage cleaning machine 三动压机triple-action press折边机edging machine开卷机decoiling unit万能液压机universal hydraulic machine 机械压力机mechanical press气动压力机pneumatic press冲孔机punch machine弯曲机弯管机pipe bending machine辊压机rolling press滚式弯板机roll-type sheet bending machine 板料校平机sheet flattening machine退料板stripper高速棒料剪切机high speed cropping machine剪床shearing machine转塔式冲床turret-type punch press校直机straightener挤压机extrusion press滚压挤压机hydraulic extrusion press 卷边机folding machine精压机coining press上料器loader落料机blanker搓丝机thread rolling machine滚剪机roller shearing machine 焊接welding十字接头cross-shaped jointT 形接头T joint单J 形坡口single-J groove单U 形坡口single-U groove双V 形坡口double-V grooveK 形坡口double-vevel groove双V 形对接接头double-V butt jointY 形坡口裂缝试验Y-slit crack testTIG 保护焊tungsten inert gas (TIG) arc welding TIG 点焊TIG spot welding立焊vertical position of welding火焰钎焊brazing by flame气体保护电弧焊gas shield arc welding气焊gas welding气电焊electrogas arc welding水下焊接underwater welding水蒸气保护电弧焊water vapor arc welding水平角焊horizontal fillet welding手工焊manual welding手工电弧焊covered arc welding仰焊face-up bonding正面角焊缝front fillet weld加压气焊gas pressure welding加压铸焊pressure thermit welding 返修焊rewelding向上立焊vertical up welding向下立焊vertical down welding平焊（俯焊）flat position welding点焊point welding双面焊weld from both sides双面点焊direct welding双弧焊twin arc welding压焊pressure welding多道焊multipass welding多点凸焊multiple projection welding 多层焊multilayer welding定位焊tack welding冷压焊cold pressure welding环焊boxing自动焊接automatic welding自动点焊stitch welding自动气割automatic gas cutting无气体保护电弧焊non gas shielded arc welding 对接焊butt welding补焊repair welding深溶焊deep penetration welding滚对焊butt seam welding滚焊seam welding滚点焊roll spot welding横焊horzontal position welding 横向焊缝cross weld金属极惰性气体保护点焊metal inert gas arc welding 金属极电弧焊接metal arc welding电焊eletric welding电子束焊接electron beam welding电子加热钎焊electric brazing电阻焊electric resistance welding 电弧焊electric arc welding堆焊bead welding坡口焊groove welding封底焊道sealing run搭接焊lap welding激光焊接laser welding热焊hot weld单面焊welding by one side单面点焊indirect welding单道焊single-pass welding单层焊single-layer welding单边多点点焊series spot welding单边多电极焊series welding仰焊overhead position welding 熔焊fusion welding氩弧焊argon arc welding跳焊skip welding惰性气体保护焊inert-gas welding埋弧自动焊unionmelt welding碳弧焊carbon arc welding躺焊fire-cracker welding缝焊seam welding锻焊blacksmith welding磁性气体保护焊gas shielded magnetic flux arc welding 焊接工艺welding procedure焊态as-welded焊道bead焊肉致密dense deposits焊后强度as-deposited strength 焊道裂纹bead cracking焊缝seam焊根root of weld焊波ripple焊透complete penetration 未焊透incomplete penetration 焊核nugget熔滴droplet熔敷工艺deposition techniques咬边undercut去渣deslag焊接缺陷weld defects乙炔罐acetylene cylinder乙炔发生器acetylene generator注水式乙炔发生器water to carbide generator投入式乙发生器carbide to water generator乙炔氧焊装置acetylene-welding installation 点焊钳spot welding head三相整流焊机three phase rectifier welder 三相低频焊机three phase low frequency 万能滚焊机universal seam welder手动焊炬hand torch手动焊枪hand held gun压焊机press welder交流弧焊机AC arc welding machine多点焊机multiple spot welder多站电焊机multi-operator welding set 切割机cutting machine气瓶gas cylinder保护罩protective boot电子枪electron gun电阻对焊butt resistance welding电焊机electric welding电弧焊机arc welding machine电渣焊机electroslag welding仿型氧气切割机template-type axy-cutting machine 抽头式焊机welder with taps仰焊机overhead welder单站弧焊机single operator welding machine 移动式焊机portable welding machine移动式接触焊机portable resistance welder移动式点焊机portable spot welder 蓄电池式焊机battery welder缝焊机seam welder大焊丝盘large spool焊工用玻璃welding galss焊工用护目镜welding goggles焊工用面罩helmet shield焊把holder乙炔acetylene电石calcium carbide电极（焊条）electrode手涂焊条dipped electrode合金焊条hastelloy electrode双芯焊条twin electrode双层药皮焊条double coated electrode机械压涂焊条extruded electrode包丝焊条flyspun electrode深熔焊条deep penetration electrode 铁粉焊条iron powder electrode堆焊焊条surfacing electrode碳极carbon electrode机加工machining车削turn高速切削high speed cutting 强力切削power cutting多刀切削multi-tool cutting 深孔加工deep hole working 高速精镗high speed boringh 高速滚削high speed hobbing 平面铣削surface milling镗削boring拉削broaching成型拉削form broaching连续拉削continuous broaching 分层拉削progressive broaching 推削push broaching刨削shaping (planing)磨削grinding外圆磨削cylindrical grinding 内圆磨削internal grinding端面磨削cross grinding周面磨削peripheral grinding 插削slotting铲削relieve钻削drill导电磨削electrical grinding 无心磨削centerless grinding 高速磨削high-speed grinding 强力磨削power grinding珩磨honing研磨lapping超精加工superfinishing齿面加工gear face machining 拉齿broaching gear铣齿gear milling插齿gear shaping滚齿gear hobbing刨齿gear planing剃齿gear shaving研齿gear lapping珩齿gear honing磨齿gear grinding挤齿gear extruding 普通剃齿法general shaving 对角剃齿法diagonal shaving 切向剃齿法tangential shaving剃鼓形齿crown shaving砂带磨削abrasive belt gringding滚压光加工rolling finishing单面切削法single-side cutting method双面切削法spread -blade cutting method展成法切齿gear-cutting with generating method 仿形法切齿gear-cutting with form copying method 成型插齿shear-speed gear cutting花键加工splining螺纹铣thread milling螺纹磨thread grinding镗孔boring hole铰孔ream锪孔counter sinking滚丝thread rolling套丝thread chaing攻丝thread tapping旋风切削螺纹whirl wind cutting thread 少无切削加工non-chip finish挤压光加工extrusion finishing精密加工precision work超精加工superfinishing粗加工rough machining化学机械加工chemical mechanical working 电热加工electro-thermic working阳极机械加工anode mechanical working电脉冲加工electro-spark machining电火花加工electro-spark machining电子束加工electronic beam machining 电解加工electrolytic machining超声波加工ultrasonic machining激光加工laser machining激光硬化laser hardening 油漆paint面漆enamel沥漆区drain area调漆paint mixing浸涂dip-coatng涂底漆priming补漆paint repair喷面漆topcoating热喷漆hot spray打腻子puttying老化weathering人工干燥artificial drying 自然干燥air dry干打磨dry grinding去油（脱脂）degreasing碱法脱脂alkaline degreasing 蒸气脱脂vapor degreasing去离子水demin-water除锈derusting酸洗pickling水洗rinse热水清洗hot water rinse电泳涂层electophoretic coating喷丸处理shot blasting磨光（抛光0burnishing出光glaring罩光glazing磷化预处理phosphating pretreatment 薄膜磷化处理thin amorphous phosphating 湿碰湿wet-to-wet钝化passivating结皮现象skinning起皱wrinkling遮蔽masking凉干flash off气幕air seal喷漆室booth干式喷漆室dry spray booth水过滤式喷漆室water wash spray booth下吸式喷漆室down draft spray booth侧抽风喷漆室spray booth of side exhaust 油漆调制室paint mixing room打磨间scuff sand booth通过式烘干室passing through type baking oven 桥式烘干室bridge type baking oven辐射对流烘干室joint radiation convection oven 浸漆设备dip equipment浸漆槽dip tank循环槽recirculating tank自动喷漆机automatic sprayer热喷漆机flow coating equipment淋漆设备flow coating equipment手工浸漆设备hand dip equipment无空气喷涂设备airless spray equipment电泳涂漆设备electro apparatus电涂漆设备electrocoating installation 静电喷漆设备electrostatic spray equipment 喷枪spray gun双头喷枪double head spray gun空气喷枪air spray gun吊具sling推杆悬链double-chain conveyer悬挂运输链overhead conveyer油水分离器oil-water separator油漆调制罐paint mixing tank除尘装置dust collector静电除尘装置electrostatic dust collector 阴极罩cathode shiedl超滤装置ultrafiltration device喷砂机sand blasting machine红外线固化IR curing紫外线固化UV curing电子束固化electron beam curing辐射固化漆膜radiation cured coating (RCC) 光泽计glossmeter比重计gravimeter粘度计viscosimetr细度计fineness gauge厚度计thickness gauge遮盖力测定仪cryptometer电镀electroplating预镀（冲镀）striking防镀（止镀）resist无氰电镀non-cyanide plating 化学电镀electroless plating 气相电镀vapor plating挂镀rack用假阴极电镀dummying机械电镀mechanical plating 浸镀immersion plating 退镀stripping滚镀barrel plating电解沉积electrowinning混浊度turbidity侵蚀fretting侵渍作用maceration亲水的hydrophilic疏水的hydrophobic絮凝剂flocculant光亮镀层bright coating防腐镀层coating for protection against corrosion 冲洗flush打光lapping抛光burnishing滚光tumbling变色tarnishing电解electrolysis沉淀法decantation抗暗处理anti-tarnish treatment均镀力levelling power深镀能力covering power酸洗pickling磷化phosphating镀锌galvanizing漂白whiten出斑点spotting out电镀机plating machine自动电镀装置automatic plating machine直线式电镀机straight-line plating machine 挂式电镀机plating machine held on racks钟形滚镀机oblique-barrel plating machine 微型滚镀机portable plating barrel冷水槽cold rinse bank双联冷水槽double countercurrent rinse tank 电解去油槽electrolytic cleaner衬铅槽lead lined steel tank哈林电槽haring cell热水槽hot rise tank超声波去油槽ultrasonic cleaning tank浸酸槽acid dip tank温水槽warm rinse tank赫尔槽hull cell镀锌槽zinc-plating tank固定槽plating tank回收槽reclaim tank水平全浸式滚筒horizontally fully-immersed barrel 六角滚筒hexagonal plating barrel孔板流量计orifie meter浊度计nephelometer库仑计coulometer滴重计stalagmometer汽车制造设备manufactruing equipment of automobile 万能铣床universal milling machine内外圆研磨床inner-outer happing machine仿形车床copy lathe龙门刨床double housing planer牛头刨床shaper攻丝机threading machine双柱坐标镗床double pillar jig borer滚丝机thread roller滚齿机hobbing machine钻床drilling machine插床slotting machine珩齿机gear honing machine平衡-钻中心孔机床balancing centering machine曲轴车床crankshaft turning lathe双工位曲轴车床double-post carnkshafttruning blathe曲轴（主轴颈）车床crankshaft (main journal turning lathe) 凸轮轴（轴颈）车床camshaft(journal )turning lathe液压仿形车床dydraulic coping lathe凸轮轴仿形车床camsahft coping lathe多轴深孔钻床multi-spindle deep hole drilling machine 曲轴轴颈铣削专用机床crankshaft journal milling machine数控曲轴铣床N/C crankshaft milling machine螺纹铣床thread milling mahcine球面蜗杆铣床cone-worm milling machine花键轴铣床spline shaft milling mahcine转鼓铣床drum milling machine旋风式曲轴铣床whirl-wind type crankshaft milling machine 曲轴主轴颈磨床cranksahft journal grinding machine凸轮轴磨床camshaft grinding machine螺纹磨床thread grinding machine活塞销超精加工机piston pin superfinishing machine弹簧端面磨床grinding machine for spiral spring活塞椭圆磨床。
机械术语中英文对照
机械术语中英文对照机械是一个应用广泛的学科，而机械术语也因此显得格外重要。
机械术语不仅在机械领域内使用广泛，还在与机械有关的其他领域中广泛运用。
本文将为大家介绍机械术语的中英文对照，帮助读者更好地理解机械术语。
一、机械结构相关1.1 机械结构英文：Mechanical structure中文：机械结构1.2 机械零件英文：Mechanical part中文：机械零件1.3 缸体英文：Cylinder block中文：缸体1.4 活塞英文：Piston中文：活塞1.5 曲轴英文：Crankshaft中文：曲轴1.6 飞轮英文：Flywheel中文：飞轮1.7 转速英文：Rotation speed中文：转速1.8 扭矩英文：Torque中文：扭矩1.9 传动轴英文：Transmission shaft 中文：传动轴1.10 传动比英文：Transmission ratio 中文：传动比二、机械加工相关2.1 加工中心英文：Machining center中文：加工中心2.2 数控机床英文：Numerical control machine tool 中文：数控机床2.3 刀具英文：Tool中文：刀具2.4 精度英文：Accuracy中文：精度2.5 加工误差英文：Machining error中文：加工误差2.6 表面光洁度英文：Surface roughness中文：表面光洁度2.7 加工粗糙度英文：Machining roughness 中文：加工粗糙度2.8 加工硬度英文：Machining hardness 中文：加工硬度2.9 切削速度英文：Cutting speed中文：切削速度2.10 进给速度英文：Feed rate中文：进给速度三、机械控制相关3.1 控制系统英文：Control system中文：控制系统3.2 机电一体化英文：Mechatronics中文：机电一体化3.3 伺服电机英文：Servo motor中文：伺服电机3.4 步进电机英文：Stepper motor中文：步进电机3.5 编码器英文：Encoder中文：编码器3.6 控制器英文：Controller中文：控制器3.7 嵌入式系统英文：Embedded system 中文：嵌入式系统3.8 传感器英文：Sensor中文：传感器3.9 特征提取英文：Feature extraction中文：特征提取3.10 监控系统英文：Monitoring system中文：监控系统机械术语中英文对照不仅包含机械结构、机械加工和机械控制等方面，还有机械力学、流体力学、材料科学等相关方面的术语。
机械名词英译汉大全
机械名词英译汉大全机械行业是一个广泛的领域，其中包含了许多特定的名词和术语。
了解这些名词的英文翻译对于学习机械工程和通信非常重要。
本文将带您了解机械名词英译汉的大全，让您更好地掌握机械工程领域的专业术语。
A•Acceleration: 加速度•Actuator:执行器•Angular velocity: 角速度•Automation:自动化•Axis:轴B•Bearing:轴承•Bevel gear:锥齿轮•Bolt:螺栓•Bore:孔径•Bushing:套筒C•Cam:凸轮•Carrier:承载体•Clutch:离合器•Crankshaft:曲轴•Cylinder:气缸D•Deflection:挠曲•Die:模具•Drive:驱动•Dynamic:动态的E•Efficiency:效率•Elasticity:弹性•Encoder:编码器•Engine:发动机F•Fastener:紧固件•Fatigue:疲劳•Friction:摩擦•Fuel:燃料G•Gear:齿轮•Generator:发电机•Grinder:砂轮•Guide:导轨H•Heat exchanger:换热器•Hydraulic:液压的•Hose:软管•Hub:轮毂I•Idle:空闲的•Inertia:惯性•Inlet:进口•Implement:工具•Jack:千斤顶•Joint:接头•Junction:连接点•Jig:夹具K•Key:键•Kinematics:运动学•Knurling:滚花L•Laser:激光•Lever:杠杆•Lubricant:润滑剂•Lathe:车床•Machine:机器•Machining:加工•Maintenance:维护•Martensite:马氏体N•Nozzle:喷嘴•Newton:牛顿•Nonferrous:有色的•Nylon:尼龙O•Orifice:孔隙•Outlet:出口•Overload:过载P•Piston:活塞•Pulley:滑轮•Pressure:压力•Pneumatic:气动的Q•Quenching:淬火•Quick-release:快速释放•Quill:芯轴•Queue:队列R•Reducer:减速器•Reliability:可靠性•Rivet:铆钉S•Shaft:轴•Screw:螺丝•Spring:弹簧•Static:静态的T•Torque:力矩•Tolerance:公差•Thread:螺纹•Turbine:涡轮机U•Ultrasonic:超声的•Upset:擴頭•Uniform:均匀的•U-bolt:U形螺栓V•Velocity:速度•Valve:阀门•Vibration:振动•Vacuum:真空W•Welder:焊工•Worm gear:蜗杆齿轮•Welding:焊接•Wear:磨损X•X-axis:X轴•Xenon:氙气•X-ray:X射线•Xerography:静电复印Y•Yoke:夹具•Y-axis:Y轴•Yield strength:屈服强度•Yarn:纱线Z•Z-axis:Z轴•Zinc:锌•Zero clearance:零间隙•Zone:区域以上是机械名词英译汉大全，包含了机械工程领域中常见的名词和术语。
机械类专业词汇中英文对照翻译表大全
机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics; human engineering人体尺寸 human dimension人体测量学 anthropometry; anthropometrics刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver 丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角尺 set square三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰?胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellac士巴拿；扳手 spanner大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB)小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench; working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU)中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF) 中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies 分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltage divider隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off 切断工具 parting tool勾；勾脚 hook勾刀；胶片?刀 plastic cutter 化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier 反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe; woodworking lathe木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB) 水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch五画丙烯?丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fitting凸轮传动 cam drive凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining 半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon; polyamide (PA)尼龙墨水针笔 technical felt-tip pen左右调校杆 lateral adjusting level市售尺寸；标准尺寸 stock size市电频率；电源频率 mains frequency平(木)锉 flat rasp平水尺；水平仪 spirit level平行投影 parallel projection平行车削 parallel turning平行虎钳 parallel vice平行钉法 parallel nailing平底弯刨 flat faced spokeshave平底钻嘴 forstner bit平板结构 slab construction平流扼流圈；滤波扼流器 smoothing choke平流电容器；滤波电容器 smoothing capacitor 平流电路；滤汳电路 smoothing circuit平面板；正台 surface plate平面图；俯视图 plan平面锤 flatter平移 translation平搭榫 corner halving joint平嘴钳 flat nose pliers平槽刨 router plane平衡 balance; equilibrium平衡力 equilibrant平衡条件 equilibrium condition平衡电桥 balanced bridge平头弧刀 square nose gouge幼纹 smooth cut打凹成形 hollowing打凸成形 raising打槽机 routing machine打线；打槽 routing打磨 fitting; polishing打磨机 polisher本生灯 Bunsen burner本征半导体 intrinsic semiconductor 正反器；触发器；复振器 flip-flop 正反馈；正回输 positive feedback 正火 normalizing正向偏置 forward bias正投影 orthographic projection正投影图 orthographic drawing正弦波形 sinusoidal waveform正面投影 front projection正视图 elevation; front elevation 正极；阳极 anode正齿轮 spur gear正台；平面板 surface plate永久性接合 permanent joining瓦通纸；瓦楞纸板 corrugated board生长层 cambium layer生产图 production drawing生胶浆 rubber cement生钢；铸钢 cast steel生铁；铸铁 cast iron用途；功能 function白杨木 poplar白胶浆 PVA glue; white glue皮沙垫 leather sandbag皮革 leather皮革黏合剂 leather glue皮鞋 leather shoes目录 contents矢量；向量 vector石灰岩 limestone石英晶体振荡器 quartz crystal oscillator石棉 asbestos; asbestus石膏 Plaster of Paris示波器 oscilloscope立体图 pictorial drawing六画交流电流 alternating current (a.c.)交流电压 a.c. voltage交联结构 cross-linked structure仿饰金 gilding metal伏特 volt光力架 clear lacquer光拉软钢 bright drawn mild steel (B.D.M.S.) 光敏电阻 light dependent resistor (LDR)光测弹性学 photoelasticity光刨；滑刨 smoothing plane光电效应 photoelectric effect光泽 lustre全闭式槽榫 closed housing joint共面力 coplanar force共聚合作用 co-polymerization共聚物 copolymer共价键 covalent bond共振；共鸣；谐振 resonance印刷电路板 printed circuit board (PCB)同素异形 allotropy同轴电缆 coaxial cable同温 equality of temperature向量；矢量 vector向量和 vector sum104合力 resultant force合口扁钳 close mouth tongs合成色；等和色 secondary colour合成品 composite合成粅料 composite material合金 alloy合金工具钢 alloy tool steel合钉；定位销 dowel回火 tempering回复力 restoring force回复力偶 restoring couple回弹 resilience回输；反馈 feedback地线 earth wire多刃切削刀具 multi-point cutter多孔塑料；泡沫塑料；海绵状塑料 foam plastics多方榫接合 pinned joint多媒体 multi-media多晶性 polycrystallinity多谐振动器；多谐振荡器 multivibrator 多边形力学；力多边形 polygon of force 字母冲 letter punch字板 letter stencil安全 safety安全守则 safety rule安全系数 safety factor安全措施 safety precaution105安全眼罩 safety goggle安全设备 safety equipment安全药箱 safety box安培 ampere安培计；电流表 ammeter尖脚 spur年轮 annual ring成本 cost成形 forming扣件；击固件 fastener扣钉 clout nail; cramp托架 bracket收缩 shrinkage曲柄 crank曲柄轴 crank shaft曲线规；云板；云尺 French curve有效的 efficient有效电流 effective current灰；灰末 ash百折胶；百折胶；聚丙烯 polypropylene (PP) 竹 bamboo羊角锤 claw hammer老化 ageing肋条 rib肌理；质感；质地 texture自由度 degree of freedom自动控制 automatic control106自动进给 auto-feed自然干燥法 natural seasoning自感量 self-inductance自感应 self-induction色彩；颜色 colour色调 tone色环 colour wheel行星齿轮；周转齿轮 epicyclic gear七画肘节开关 toggle-switch串激电动机；串绕电动机 series-wound motor 位能；势能 potential energy位梯度；势梯度 potential gradient位移 displacement位错 dislocation伸长度 elongation作工硬化 work hardening作功 work done作图线 construction line低密聚乙烯 low density polyethylene (LDPE) 低通滤波器 low-pass filter低电压 low voltage低碳钢 low carbon steel布置 layout免油轴承 oil-less bearing冷加工；冷作工 cold working冷加工硬化 cold work hardening冷色 cool colour冷轧压 cold rolling冷却系统 cooling system冷却效应 cooling effect冷却液流量 coolant rate冷凝胶；环氧树脂 epoxy resin108利口；「披」口；铁屑 burr刨平 planing刨花板；碎料板 particle board吹风机 air blower吹气模塑；吹模塑 blow moulding吹管 blow pipe含铁金属 ferrous metal含水量 moisture content坑凿 cross-cut chisel均方根值 root mean square value均角投影图；等角投影图 isometric drawing 均速圆周运动 uniform circular motion 夹；夹钳 clamp夹 cramp夹卡 mounting board夹具 fixture; jig夹具及固定装置 jig and fixture夹板；胶合板 plywood夹持工具 clamping device; holding tool夹背锯；榫锯 tenon saw夹头 chuck夹头开启匙；夹头扳手 chuck key夹叠黏合成形 lamination尾座 tailstock床身；床道 lathe bed床鞍；刀座帷 apron形心；面心 centroid109形状 shape形变 deformation「快把」板；硬质纤维板 hardboard快速移位 rapid traverse抗扭强度 torsional strength抗屈强度 bending strength; yield strength 抗性分量；无功分量 reactive component抗拉强度 tensile strength抗氧化剂 anti-oxidant抗剪强度 shearing strength抗磁性物料 diamagnetic material抗挠性 stiffness抗压强度 compressive strength抗断强度 breaking strength技术员；技师 technician扶架 steady扭力 torsion扭矩；转矩 torque扭转 torsion扭转角 angle of torsion把手 hand grip扼流圈 choke扳手 spanner; wrench投影 projection投影面 projection plane投影线 projection line攻丝 tap材料 material材料单；材料表 material list杜拉铝 duralumin杉木 spruce步进电动机 stepper motor步冲轮廓法 nibbling每分钟转数 revolution per minute (r.p.m.) 系统组件 system component角托架 angle bracket角位移 angular displacement角板；直角板 angle plate角度 angle角榫 corner angle joint; corner joint角铁 angle iron谷巴凡立水 cobal varnish车刀架 tool holder车床 lathe车床工具 lathe tools车床中心钻咀 lathe centre bit车床操作法 lathe operation车削；车旋 lathe turning; turning车削工具 turning tools防火胶板 Formica防锈 rust prevention防声耳筒；护耳器 ear-protector防松螺帽 lock nut防护装置；保护罩；保护网 guard; safety guard八画注射成形法；喷射铸造法 injection moulding并激电动机；并绕电动机 shunt-wound motor乳酪胶 casein glue乳胶漆 emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)亚稳态的；介稳态的 metastable来回摆动 oscillating两点透视 two-point perspective刻度；划线 ruling刺冲 dot punch刮刀 scraper刮擦 scraping制动鼓 drum brake制动碟 disc brake制动器 brake受迫振动 forced vibration受迫振荡 forced oscillation和谐 harmony周转齿轮；行星齿轮 epicyclic gear固定夹；台夹 bench holdfast固定负载 dead load定子 stator定位销；合钉 dowel定位螺丝 set screw定距轮 stitch marker屈片机 folding machine屈曲 bending屈服点；降服点 yield point屈圈法 loop forming屈卷法 scrolling屈接缝 folded lap seam屈喉机 tube bender屈折 folding屈折线 folding line屈压接缝 folded & grooved seam延性 ductility延性的 ductile弦锯法 plain sawing弧口凿；圆凿 gouge往复式运动 reciprocatory motion拉力 tensile force拉力计；张力计 tensiometer; tensometer拉钉 blind rivet; pop rivet拉钉接合 blind riveting; pop riveting拉钉钳 blind riveting pliers; pop riveting pliers 拉张 tension拉张应力 tensile stress拉张应变 tensile strain拉细 drawing-down拉制法 drawing拉线 wire drawing「披」口；利口；铁屑 burr拔钳 nippers拋光 buffing拋光机 buffing machine放大；扩大 enlargement放大尺 pantograph放大倍数 amplification factor放大器 amplifier放电极加工；火花电蚀法 electrical discharge machining 易用万能尺 line setter易碎 fragile〈绘画的〉明暗运用；描影 shading枝；杆 rod杯形顶尖 cup centre杯头螺丝 hexagonal socket head cap screw板锯 panel saw松木 pine松节水 turpentine法式磨光 French polishing法拉〈电容量单位〉 farad油石；磨刀石 oil stone油漆；涂料 paint泡沫塑料；多孔塑料；海绵状塑料 foam plastics物理特性 physical property物理属性 physical attribute物理量 physical quantity盲孔；闭孔；不贯穿孔 blind hole直尺 ruler; straight rule直角叉榫 corner bridle joint直角尺 try square直角板；角板 angle plate直角杠杆 bell crank lever直身钻嘴 straight shank drill直车刀架 straight tool holder直流发电机 d.c. generator直流电流 direct current (d.c.)直流电动机；直流马达 d.c. motor直纹锯 rip saw直线切削 linear interpolation直线运动 rectilinear motion直边凿；方边凿 firmer chisel直铁剪 straight snips硅 silicon空行程 idle stroke空气动力学 aerodynamics空间 space空载 no load花纹凿 embossing stamp花梨木 rosewood花样；图案 pattern虎克定律 Hooke's Law虎钳 vice虎钳护罩 vice clamp初步意念 proposed solution表面 surface表面展开图 surface development表面张力 surface tension表面处理 surface finishing; surface treatment 表面硬化 case hardening表面硬化钢 case-hardened steel表达方式 presentation表达技巧；传意技巧 communication technique表观膨胀；视膨胀 apparent expansion金工 metalwork金工工作间 metalwork area金工角尺 engineering square金工车床 metalwork lathe金工虎钳 engineer's vice金工锯床 power hacksaw金属包头；金属箍 ferrule金属配件 metal fittings金属线 wire金属压展机 hand rolling mill金属擦光剂；磨光剂 metal polish金属薄片 sheet metal金属键 metallic bond长方通 rectangular tube长刨 trying plane长螺旋钻咀 long auger bit长镗孔 long boring闸极 gate阻抗 impedance附件 attachment附录 appendices青铜 bronze非反相放大器 non-inverting amplifier非本征半导体 extrinsic semiconductor非破坏性试验 non-destructive testing非晶状固体 amorphous solid非顽磁性铁磁材料 non-retentive ferromagnetic material 非压缩性流体 incompressible fluid非稳态 unsteady state非铁金属；不含铁金属 non-ferrous metal九画亮漆；力架 lacquer信号 signal信号产生机 signal generator信号处理 signal processing保养；维修 maintenance保险丝 fuse保护罩；保护网；防护装置 guard; safety guard促凝剂 accelerator削屑 swarf垂直投影面 vertical plane型砧 swages〈书的〉封皮 binding封面 cover急回机构 quick return mechanism 扁枝 bar扁头 cross-pein扁头法 upsetting扁头铆钉 flat head rivet扁头螺丝 flat head screw扁凿 flat chisel指示器 indicator指形榫 finger joint施力 effort染色 staining染色剂 stain架构 framework柄 stock柚木 teak柳安木 lauan。
机械类中英文对照汇总
机械类中英文对照汇总（一）机械设计及生产常用词中英文对照表Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表 notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传 rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疵shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车 mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机（二）冲压模具-冲压名称类英汉对照plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量（三）动力机械常用词汇二冲程内燃机 two-stroke internal combustion engine十六烷值 cetane number工业汽轮机 industrial steam turbine工业锅炉 industrial boilerx内燃机冷却系统 cooling system of internal combustion engine 内燃机起动装置 starting device of internal combustion engine 内燃机配气机构 valve mechanism of internal combustion engine 内燃机动力学 engine dynamics内燃机排污 exhaust emission of internal combustion engine内燃机轴系扭转振动 torsional vibration of engine crankshaft内燃机寿命 service life of internal combustion engine内燃机润滑系统 lubrication system of internal combustion engine 内燃机调速器 governor for internal combustion engine内燃机噪声 noise of internal combustion engine分电器 distributor化油器 carburettor水冷壁 water wall水轮机 hydraulic turbine火花塞 spark plug四冲程内燃机 four-stroke internal combustion engine示功图 indicator diagram示功器 indicator再热器 reheater自由活塞式发动机 free-piston engine吹灰器 soot blower汽水分离－再热器 moisture separator reheater汽车发动机 automotive engine汽油喷射发动机 gasoline injection engine汽轮机工作原理 basic principle of steam turbine汽轮机旁路系统 steam turbine bypass system汽轮机控制系统 steam turbine control system汽轮机热力性能 steam turbine performance辛烷值 octane number供热式汽轮机 steam turbine for cogeneration往复活塞式内燃机 reciprocating piston internal combustion engine 抽汽式汽轮机 extraction steam turbine沸腾炉 fluidized bed combustion boiler空气预热器 air preheater空气滤清器 air cleaner流体力学 fluid mechanics省煤器 economizer背压式汽轮机 back-pressure steam turbine风力机 wind machine核电站汽轮机 nuclear steam turbine核蒸汽供应系统 nuclear steam supply system气波增压器 comprex supercharger能源 energy source旋风炉 cyclone furnace旋转活塞式发动机 rotary engine船用汽轮机 marine steam turbine船用柴油机 marine diesel engine船用锅炉 marine boiler透平 turbine透平叶片 turbine blade斯特林发动机 Stirling engine给水加热器 feed water heater传热学 heat transfer煤气机 gas engine过热器 superheater电站锅炉 utility boiler饱和蒸汽轮机 saturated steam turbine磁电机 magneto蓄热器 accumulator蒸汽动力装置 steam power equipment蒸汽发生器 steam generator蒸汽机 steam engine喷油泵 injection pump喷油器 fuel injector废气涡轮增压 exhaust turbocharging热力学 thermodynamics热水锅炉 hot water boiler热气机 hot-air engine复合式发动机 compound engine餘热锅炉 waste heat boiler凝汽器 condenser机车柴油机 locomotive diesel engine燃气透平 gas turbine燃气－蒸汽联合循环装置 gas and steam combined cycle installation 燃气轮机控制系统 gas turbine control system燃气轮机循环 gas turbine cycle燃气轮机燃烧室 gas turbine combustion chamber燃气轮机变工况性能 gas turbine off-design performance燃烧器 burner燃烧学 combustion science磨煤机 coal pulverizer压缩比 compression ratio锅驼机 locomobile锅炉水处理 boiler water treatment锅炉自动控制 automatic boiler control（四）通用机械常用词汇制冷剂 refrigerant阀门驱动装置 valve actuator热泵 heat pump热管 heat pipe蝶阀 butterfly valve余摆线真空泵 trochoidal vacuum pump齿轮泵 gear pump横流通风机 crossflow fan膨胀节 expansion joint膨胀机 expander压缩式制冷机 compression refrigerating machine 压滤机 filter press螺旋板换热器 spiral heat exchanger螺杆泵 screw pump螺杆压缩机 screw compressor滤油机 oil filter转鼓真空过滤机 rotary-drum vacuum filter转盘式换热器 rotary disk heat exchanger离心泵 centrifugal pump离心通风机 centrifugal fan离心压缩机 centrifugal compressor罗茨真空泵 Roots vacuum pump罗茨鼓风机 Roots blower制冷剂 refrigerant阀门驱动装置 valve actuator热泵 heat pump热管 heat pipe蝶阀 butterfly valve余摆线真空泵 trochoidal vacuum pump齿轮泵 gear pump横流通风机 crossflow fan膨胀节 expansion joint膨胀机 expander压缩式制冷机 compression refrigerating machine压滤机 filter press螺旋板换热器 spiral heat exchanger螺杆泵 screw pump螺杆压缩机 screw compressor滤油机 oil filter转鼓真空过滤机 rotary-drum vacuum filter转盘式换热器 rotary disk heat exchanger离心泵 centrifugal pump离心通风机 centrifugal fan离心压缩机 centrifugal compressor罗茨真空泵 Roots vacuum pump罗茨鼓风机 Roots blower（五）热加工工艺和设备常用词汇千焊 soldering and brazing工业炉砌体 brickwork of industrial furnace工业炉排烟系统 fume dischange system for industrial furnace 工业炉预热器 preheater for industrial furnace工业炉燃烧装置 combustion device for industrial furnace井式炉 vertical pit furnace少无切削加工 chipless forming手工电弧焊 shielded metal arc welding水下切割 underwater cutting水下焊 underwater welding水压机 hydraulic forging press火焰淬火 flame hardening可控气氛 controlled atmosphere可锻铸铁 malleable cast iron台车式炉 car-bottom type furnace平锻机 horizontal forging and upsetting machine正火 normalizing再生砂 reclaimed sand回火 tempering成形轧制 forming rolling自由锻 open die forging低压铸造 low-pressure casting冷压焊 cold pressure welding冷鐓 cold upsetting形变热处理 thermomechanical treatment冲天炉 cupola拉深 deep drawing拋丸机 shot blasting machine泥型铸造 clay mold casting芯砂 core sand芯盒 core box表面合金化 surface alloying金属型铸造 permanent mold casting金属清理 metal cleaning金属喷涂 metal spraying金属热处理加热方法 heating method for metal heat treatment 金属热处理质量控制 quality control for metal heat treatment 冒口 riser型砂 molding sand型砂黏结剂 molding sand binder室式炉 chamber furnace砂型乾燥炉 mold dring oven砂型铸造 sand mold casting负压铸造 V-process埋弧焊 submerged arc welding径向锻造 radial forging时效处理 aging气焊 gas welding气割 gas cutting气体保护电弧焊 gas shielded arc welding真空热处理 vacuum heat treatment真空炉 vacuum furnace退火 annealing高能率成形 high energy-rate forming高速锤锻造 high energy-rate forging高频焊 high-frequency welding堆焊 surfacing旋压 spining旋转电弧焊 rotating arc welding混砂机 sand mixer淬冷介质 quenching media焊接安全与卫生 health and safety in welding 焊接性 weldability焊接设备 welding equipment焊接结构 welded structure焊接质量 welding quality焊接应力和变形 welding stress and distortion 焊条 covered electrode焊丝 welding wire焊剂 welding flux球墨铸铁 nodular cast iron连续式炉 continuous furnace连续铸造 continuous casting造芯机 core-making machine造型机 molding machine陶瓷型铸造 ceramic mold casting壳型铸造 shell mold casting无机覆层 inorganic coatings发蓝 blueing等离子弧切割 plasma arc cutting等离子弧焊 plasma arc welding胀形 bulging超塑成形 superplastic forming超声波焊 ultrasonic welding塑性变形 plastic deformation涂装 paint coating感应加热热处理 induction heat treatment感应炉 induction furnace落砂机 shakeout machine电子束焊 electron beam welding电化学保护 electrochemical protection电弧切割 arc cutting电弧炉 arc furnace电阻焊 resistance welding电阻炉 resistance furnace电渣焊 electroslag welding电镀 electroplating实型铸造 full mold casting渗金属 diffusion metallizing渗氮 nitriding渗碳 carburizing熔模铸造 investment casting摩擦焊 friction welding暂时性防护 temporary protection模具 die and mould模样 pattern（六）冷加工工艺和设备常用词汇三坐标测量机 three dimensional measuring machine 千分尺 micrometer工具磨床 tool and cutter grinding machine工具显微镜 tool maker's microscope工业机器人 industrial robot内圆磨床 internal grinding machine分度头 dividing head切削用量 machining data切削液 cutting fluid孔径测量 inside diameter measurement木工刀具 wood cutting tool木工刨床 wood planing machine木工车床 wood working lathe木工砂光机 wood sanding machine木工铣床 wood moulding machine木工锯机 wood sawing machine木工钻床 wood boring machine比长仪 comparator水平仪 level牛头刨床 shaping machine主动测量 in-process measurement加工中心 machining center卡盘 chuck可转位刀具 cutting tool with indexable inserts外圆磨床 cylindrical grinding machine平尺 straight edge平板 surface plate平面度测量 flatness measurement平面度测量仪 flatness measuring instrument平面磨床 surface grinding machine平晶 optical flat正弦规 sine bar立方氮化硼 cubic boron nitride立式车床 vertical turning and boring mill立式钻床 vertical drilling machine交换齿轮 change gears仿形机床 copying machine光刻 photoetching光栅 optical grating光电显微镜 photoelectric microscope多面棱体 polygon多齿分度台 multiteeth indexing table百分表和千分表 dial indicator自动车床 automatic lathe自动开合螺纹切头 self-opening die head and self-collapsing tap 刨刀 shaping and planing tool刨削 shaping and planing吸盘 holding chuck坐标磨床 jig grinder坐标鏜床 jig boring machine扳手 wrench投影仪 measuring projector角度测量 angle measurement角度量块 angle gauge block车刀 turning tool车削 turning刻线机 graduating machine刮削 scraping弧齿锥齿轮铣齿机 spiral bevel and hypoid gear generator拉刀 broach拉床 broaching machine拉削 broaching拋光 polishing升降台铣床 knee and column milling machine板牙 threading die油石 oilstone直尺 knife edge直线度测量 straightness measurement直齿锥齿轮刨齿机 straight bevel gear generator卧式鏜床 horizontal boring machine花键加工 spline processing花键加工机床 spline making and finishing machine虎钳 vice表面粗糙度测量 surface roughness measurement金刚石 diamond金刚镗床 fine boring machine金属切削原理 theory of metal cutting长度计量的量值传递 dissemination of quantity in length measurement 长度计量基准 standard of length measurement长度传感器 linear transducer阿贝原则 Abbe's principle剃齿刀 gear shaving cutter剃齿机 gear shaving machine柔性制造系统 flexible manufacturing system柯氏干涉仪 Kosters interferometer砂布(纸) abrasive cloth or paper砂瓦 abrasive segment砂带 abrasive belt砂带磨床 abrasive belt grinding machine砂带磨削 abrasive belt grinding砂轮 grinding wheel砂轮修整 grinding wheel truing and dressing研磨 lapping研磨剂 lapping compound研磨机 lapping machine刚玉 aluminium oxide套料钻 trepanning tool振动料斗 vibrating feeder 气动量仪 air gauge迴转工作台 rotary table珩齿机 gear honing machine 珩磨 honing珩磨机 honing machine旋风切削 thread whirling。
机械专业中英文对照(完整版)
.机械专业英语词汇陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination 气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle.主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure 稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes.有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪.Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良.oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔.feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲。
(完整版)机械专业相关词汇中英文翻译大全
机械专业有关词汇中英文翻译大全单价 unit price工日共计 Man-day total/work-day total人工费 cost of labor资料费 materials expenses机械的 mechanical检查接线 connection test发电机 generator调相机 phase regulator周波 cycle减负荷装置 load-shedding equipment断路器柜 circuit breaker cabinet单母线 single busbar互感器 transformer每相电流 Current by Phase关闭式插接 close type socket joint发电机控制面板generator control panel分级卸载 sorted unloading同步控制 synchronization control调速器 speed governor信号屏 signal screen继电器 relay高压柜 high pressure cabinet油浸电力变压器oil-immersed power transformer空气断路器 air circuit breaker控制屏 control panel直流馈电屏 direct current feed control panel电容器 electric condenser计量盘 metering panel成套配电箱 whole set of distribution box落地式 floor model控制开关 Control switches铜芯电力电缆 Copper core power cable控制电缆 actuating cable热缩式电力电缆终端头 pyrocondensation power cable terminal 钢构造支架配管 steel structure bracket tubing万用槽钢 versatile U-steel电缆托架 cable bracket钢制托盘式桥架 steel Tray-type cable support system waterproof socket 防水插座防爆插座 Explosion-proofsocket接地绞线 earthing twisted pair接地母线 earthing bus接地极 lightning conductor硬质聚氯乙烯管rigid polyvinyl chloride pipe航空集散站 air terminal水银灯具 Mercury Lamp金属卤化物灯 metal halide lamp高压钠灯 High Pressure Sodium Lamp额定电压 Rated Voltage额定功率 Rated Power光源 Light Source防备等级 Grade of Protection高压汞灯 High Pressure Mercury Lamp高压钠灯 High Pressure Sodium Lamp金属卤化物灯 Metallic Halide Lamp照明电缆 lighting cable单线 mongline穿线 threading接地跨接线 earthing jumper分线箱 junction box接线盒 connection box圆钢 round steel扁钢 flat steel插座 socket配电盘 switchboard变换开关 alternation switch自动指令呼喊装置automatic instruction calling device 扬声器 loudspeaker明装 Unfold Install暗装 Conceal Install感温探测器 Thermal Detector转台造型机turntable molding machine气动震实造型机air jarring moulding machine有箱造型机box molding machine压铸机die casting machine热室压铸机hot-chamber die casting machine 惯性落砂机inertia knock-out grid浇包ladle浇注机cating machine冲天炉cupola (cupola furnace)水冷冲天炉water cooled cupola焦碳炉coke-fired furnace退火炉annealing oven回火炉drawing furnace喷丸机high pressure blasting machine 抛砂机sand throwing machine摆轮式混砂机speedmuller自动分箱机automatic box splitter自动合箱机automatic closer自动壳型机autoclino风动工具air tool锻造forging无型锻造open forging水压机锻造hydraulic forging机器锻造machine forging自由锻造flat-die forging多型槽锻造multiple impression forging 冷锻cold forging锤锻（自由锻）hammer forging平锻horzontal forging镦锻upset forging辊锻roll forging模锻die forging热模锻pressure forging开式模锻open-die forging精细模锻prescision drop forging 挤压模锻no-draft forging冷拉cold draw热拉hot draw冷挤压cold extruding切边trim冷切边cold trim热切边hot trim冲孔punching校订straightening板料冲压sheet stamping制坯blank锻造毛坯forging blank上模upper die下模bottom die(counter die)上锤头top swage下锤头lower die汽锤steam hammer无砧坐模锻锤forging hammer without anvilbed 摩擦锤jump hammer落锤block hammer水均分模（平锻机）horizontal parting冷锻模cold forging die型锻模forging die精整模forming die顶锻模joggling die锻压机forging die水压机water press平锻机horizontal forging machine汽力锻压机steam power forging press 压弯机bending press模锻压力机drop press曲轴压力机crank press曲柄压力机knuckle-joint press切边压力机trimming press切断压力机cutting-out press精压机coining press辊锻机forging roll镦锻机upsetting forging press喷丸清理sand blast cleaning除去内应力residual stress relieving 水力清理hydraulic blasting酸洗pickling超声波冲洗ultrasonic cleaning超声波探伤ultrasonic inspection冲压stamping冲压下料bar stock cutting by punching 冲压线press line凸模punch凸凹模punch-die冲孔模piercing die修边模trimming die预弯模die for first-forming扭弯模twisting die扭弯模twisting die扭弯成形模twisting-forming die 压弯模bending die压弯翻边模bending-flanging die 压扁模flattening die压圆模circular bending die 压弯卷圆模bending-curling die 压弯压筋模bending-beading die 落料模blanking die落料压印模blanking-coining die 落料切槽模blanking-slotting die缩口模neckling die翻孔整形模hole flanging-sizing die 翻边成形模flanging forming die切槽模slotting die拉延模drawing die下料stock cutting开卷unreel成形forming翻边flanging反向拉伸reverse-draw整形restricking整径trued切口cut-off (shear-out)切边trimming压扁flattening应变strain压痕impression拉延drawing拉伸deep drawng挤压extrusion滚挤roll-forming卷边折边edging刮边scraping三室冲洗机three-stage cleaning machine 三动压机triple-action press折边机edging machine开卷机decoiling unit全能液压机universal hydraulic machine 机械压力机mechanical press气动压力机pneumatic press冲孔机punch machine曲折机弯管机pipe bending machine辊压机rolling press滚式弯板机roll-type sheet bending machine 板料校平机sheet flattening machine退料板stripper高速棒料剪切机high speed cropping machine 剪床shearing machine转塔式冲床turret-type punch press校直机straightener挤压机extrusion press滚压挤压机hydraulic extrusion press 卷边机folding machine精压机coining press上料器loader落料机blanker搓丝机thread rolling machine 滚剪机roller shearing machine 焊接welding十字接头cross-shaped jointT形接头T joint单J 形坡口single-J groove单U形坡口single-U groove双V形坡口double-Vgroove K 形坡口double-vevel groove双 V 形对接接头double-V butt jointY 形坡口裂痕试验Y-slit crack testTIG 保护焊tungsten inert gas (TIG) arc welding TIG 点焊TIG spot welding立焊vertical position of welding 火焰钎焊brazing by flame气体保护电弧焊gas shield arc welding气焊gas welding气电焊electrogas arc welding水下焊接underwater welding水蒸气保护电弧焊water vapor arc welding水平角焊horizontal fillet welding手工焊manual welding手工电弧焊covered arc welding仰焊face-up bonding正面角焊缝front fillet weld加压气焊gas pressure welding加压铸焊pressure thermit welding 返修焊rewelding向上立焊vertical up welding向下立焊vertical down welding 平焊（俯焊）flat position welding点焊point welding双面焊weld from both sides双面点焊direct welding双弧焊twin arc welding压焊pressure welding多道焊multipass welding多点凸焊multiple projection welding 多层焊multilayer welding定位焊tack welding冷压焊cold pressure welding环焊boxing自动焊接automatic welding自动点焊stitch welding自动气割automatic gas cutting无气体保护电弧焊non gas shielded arc welding 对接焊butt welding补焊repair welding深溶焊deep penetration welding滚对焊butt seam welding滚焊seam welding滚点焊roll spot welding横焊horzontal position welding 横向焊缝cross weld金属极惰性气体保护点焊metal inert gas arc welding 金属极电弧焊接metal arc welding电焊eletric welding电子束焊接electron beam welding电子加热钎焊electric brazing电阻焊electric resistance welding 电弧焊electric arc welding堆焊bead welding坡口焊groove welding封底焊道sealing run搭接焊lap welding激光焊接laser welding热焊hot weld单面焊welding by one side单面点焊indirect welding单道焊single-pass welding单层焊single-layer welding单边多点点焊series spot welding单边多电极焊series welding仰焊overhead position welding 熔焊fusion welding氩弧焊argon arc welding跳焊skip welding惰性气体保护焊inert-gas welding埋弧自动焊unionmelt welding碳弧焊carbon arc welding躺焊fire-cracker welding缝焊seam welding锻焊blacksmith welding磁性气体保护焊gas shielded magnetic flux arc welding 焊接工艺welding procedure焊态as-welded焊道bead焊肉致密dense deposits焊后强度as-deposited strength 焊道裂纹bead cracking焊缝seam焊根root of weld焊波ripple焊透complete penetration 未焊透incomplete penetration 焊核nugget熔滴droplet熔敷工艺deposition techniques咬边undercut去渣deslag焊接缺点weld defects乙炔罐acetylene cylinder乙炔发生器acetylene generator灌水式乙炔发生器water to carbide generator 投入式乙发生器carbide to water generator 乙炔氧焊装置acetylene-welding installation 点焊钳spot welding head三相整流焊机three phase rectifier welder 三相低频焊机three phase low frequency 全能滚焊机universal seam welder手动焊炬hand torch手动焊枪hand held gun压焊机press welder沟通弧焊机AC arc welding machine 多点焊机multiple spot welder多站电焊机multi-operator welding set 切割机cutting machine气瓶gas cylinder保护罩protective boot电子枪electron gun电阻对焊butt resistance welding电焊机electric welding电弧焊机arc welding machine电渣焊机electroslag welding仿型氧气切割机template-type axy-cutting machine 抽头式焊机welder with taps仰焊机overhead welder单站弧焊机single operator welding machine 挪动式焊机portable welding machine挪动式接触焊机portable resistance welder挪动式点焊机portable spot welder 蓄电池式焊机battery welder缝焊机seam welder大焊丝盘large spool焊工用玻璃welding galss焊工用护目镜welding goggles焊工用面罩helmet shield焊把holder乙炔acetylene电石calcium carbide电极（焊条）electrode手涂焊条dipped electrode合金焊条hastelloy electrode双芯焊条twin electrode双层药皮焊条double coated electrode 机械压涂焊条extruded electrode包丝焊条flyspun electrode深熔焊条deep penetration electrode 铁粉焊条iron powder electrode堆焊焊条surfacing electrode碳极carbon electrode机加工machining车削turn高速切削high speed cutting 强力切削power cutting多刀切削multi-tool cutting深孔加工deep hole working 高速精镗high speed boringh 高速滚削high speed hobbing 平面铣削surface milling镗削boring拉削broaching成型拉削form broaching连续拉削continuous broaching 分层拉削progressive broaching 推削push broaching刨削shaping (planing)磨削grinding外圆磨削cylindrical grinding内圆磨削internal grinding端面磨削cross grinding周面磨削peripheral grinding插削slotting铲削relieve钻削drill导电磨削electrical grinding 没心磨削centerless grinding 高速磨削high-speed grinding 强力磨削power grinding珩磨honing研磨lapping超精加工superfinishing齿面加工gear face machining 拉齿broaching gear铣齿gear milling插齿gear shaping滚齿gear hobbing刨齿gear planing剃齿gear shaving研齿gear lapping珩齿gear honing磨齿gear grinding挤齿gear extruding 一般剃齿法general shaving 对角剃齿法diagonal shaving 切向剃齿法tangential shaving剃鼓形齿crown shaving砂带磨削abrasive belt gringding滚压光加工rolling finishing单面切削法single-side cutting method双面切削法spread -blade cutting method展成法切齿gear-cutting with generating method 仿形法切齿gear-cutting with form copying method 成型插齿shear-speed gear cutting花键加工splining螺纹铣thread milling螺纹磨thread grinding镗孔boring hole铰孔ream锪孔counter sinking滚丝thread rolling套丝thread chaing攻丝thread tapping旋风切削螺纹whirl wind cutting thread 少无切削加工non-chip finish挤压光加工extrusion finishing精细加工precision work超精加工superfinishing粗加工rough machining化学机械加工chemical mechanical working 电热加工electro-thermic working阳极机械加工anode mechanical working 电脉冲加工electro-spark machining电火花加工electro-spark machining电子束加工electronic beam machining 电解加工electrolytic machining超声波加工ultrasonic machining激光加工laser machining激光硬化laser hardening 油漆paint面漆enamel沥漆区drain area调漆paint mixing浸涂dip-coatng涂底漆priming补漆paint repair喷面漆topcoating热喷漆hot spray打腻子puttying老化weathering人工干燥artificial drying自然干燥air dry干打磨dry grinding去油（脱脂）degreasing碱法脱脂alkaline degreasing 蒸气脱脂vapor degreasing 去离子水demin-water除锈derusting酸洗pickling水洗rinse热水冲洗hot water rinse电泳涂层electophoretic coating喷丸办理shot blasting磨光（抛光 0burnishing出光glaring罩光glazing磷化预办理phosphating pretreatment 薄膜磷化办理thin amorphous phosphating 湿碰湿wet-to-wet钝化passivating结皮现象skinning起皱wrinkling掩盖masking凉干flash off气幕air seal喷漆室booth干式喷漆室dry spray booth水过滤式喷漆室water wash spray booth下吸式喷漆室down draft spray booth侧抽风喷漆室spray booth of side exhaust 油漆调制室paint mixing room打磨间scuff sand booth经过式烘干室passing through type baking oven 桥式烘干室bridge type baking oven辐射对流烘干室joint radiation convection oven 浸漆设备dip equipment浸漆槽dip tank循环槽recirculating tank自动喷漆机automatic sprayer热喷漆机flow coating equipment淋漆设备flow coating equipment手工浸漆设备hand dip equipment无空气喷涂设备airless spray equipment电泳涂漆设备electro apparatus电涂漆设备electrocoating installation静电喷漆设备electrostatic spray equipment 喷枪spray gun双头喷枪double head spray gun空气喷枪air spray gun吊具sling推杆悬链double-chain conveyer悬挂运输链overhead conveyer油水分别器oil-water separator油漆调制罐paint mixing tank除尘装置dust collector静电除尘装置electrostatic dust collector阴极罩cathode shiedl超滤装置ultrafiltration device喷砂机sand blasting machine红外线固化IR curing紫外线固化UV curing电子束固化electron beam curing辐射固化漆膜radiation cured coating (RCC)光彩计glossmeter比重计gravimeter粘度计viscosimetr细度计fineness gauge厚度计thickness gauge掩盖力测定仪cryptometer电镀electroplating预镀（冲镀）striking防镀（止镀）resist无氰电镀non-cyanide plating 化学电镀electroless plating 气相电镀vapor plating挂镀rack用假阴极电镀dummying机械电镀mechanical plating 浸镀immersion plating 退镀stripping滚镀barrel plating电解堆积electrowinning浑浊度turbidity侵害fretting侵渍作用maceration亲水的hydrophilic疏水的hydrophobic絮凝剂flocculant光明镀层bright coating防腐镀层coating for protection against corrosion 冲刷flush打光lapping抛光burnishing滚光tumbling变色tarnishing电解electrolysis积淀法decantation抗暗办理anti-tarnish treatment均镀力levelling power深镀能力covering power酸洗pickling磷化phosphating镀锌galvanizing漂白whiten出斑点spotting out电镀机plating machine自动电镀装置automatic plating machine 直线式电镀机straight-line plating machine 挂式电镀机plating machine held on racks 钟形滚镀机oblique-barrel plating machine 微型滚镀机portable plating barrel冷水槽cold rinse bank双联冷水槽double countercurrent rinse tank 电解去油槽electrolytic cleaner衬铅槽lead lined steel tank哈林电槽haring cell热水槽hot rise tank超声波去油槽ultrasonic cleaning tank浸酸槽acid dip tank温水槽warm rinse tank赫尔槽hull cell镀锌槽zinc-plating tank固定槽plating tank回收槽reclaim tank水平全浸式滚筒horizontally fully-immersed barrel 六角滚筒hexagonal plating barrel孔板流量计orifie meter浊度计nephelometer库仑计coulometer滴重计stalagmometer汽车制造设备manufactruing equipment of automobile 全能铣床universal milling machine内外圆研磨床inner-outer happing machine仿形车床copy lathe龙门刨床double housing planer牛头刨床shaper攻丝机threading machine双柱坐标镗床double pillar jig borer滚丝机thread roller滚齿机hobbing machine钻床drilling machine插床slotting machine珩齿机gear honing machine均衡 - 钻中心孔机床balancing centering machine曲轴车床crankshaft turning lathe双工位曲轴车床double-post carnkshafttruning blathe 曲轴（主轴颈）车床crankshaft (main journal turning lathe)凸轮轴（轴颈）车床camshaft(journal )turning lathe液压仿形车床dydraulic coping lathe凸轮轴仿形车床camsahft coping lathe多轴深孔钻床multi-spindle deep hole drilling machine 曲轴轴颈铣削专用机床crankshaft journal milling machine数控曲轴铣床N/C crankshaft milling machine螺纹铣床thread milling mahcine球面蜗杆铣床cone-worm milling machine花键轴铣床spline shaft milling mahcine转鼓铣床drum milling machine旋风式曲轴铣床whirl-wind type crankshaft milling machine 曲轴主轴颈磨床cranksahft journal grinding machine凸轮轴磨床camshaft grinding machine螺纹磨床thread grinding machine活塞销超精加工机piston pin superfinishing machine弹簧端面磨床grinding machine for spiral spring活塞椭圆磨床。
机械类专业术语汇总(中英文对照)(DOC)
1.…………组装、冲压、喷漆等专业词汇4.…………模具工程常用词汇6.…………模具工程类6.…………五金零件类7.…………模板类7.…………零件类7.…………移转成型用模具8.…………品质人员名称类8.…………FQC运作类8.…………其它品质术语类9.…………系统文件类9.…………生产类9.…………其它10…………模具技术用语各种模具常用成形方式目录10…………各式模具分类用语11.…………模具厂常用之标准零配件12.…………模具常用之工作机械12.…………检验量测工具用语13.…………模具钢材13.…………表面处理关连用语14.…………焊接用语14.…………射出成形关联用语15.…………塑胶原料15.…………成形不良用语16.…………模具常用刀具与工作法用语16.…………电脑关联用语16.…………各种冲模加工关连用语16.…………冲压机械及周边关连用语17.…………线切割放电加工关连用语18.…………锻铸造关连用语18.…………模具加工方法18.…………学理实验与试验用语19.…………砂轮用语19.…………机械设计及周边其他用语19.…………业务与贸易关连用语20.…………附加组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice sectionsuperisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansionprojects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, toinput落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--overswitching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping 冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count 会计师盘点数量the first page第一联filed by accounting department forreference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventorybills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list willbe sent to accountingdepartment together (Those of NHK willbe sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-endphysical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectivenessanalysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-OnlyMemory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measure ment4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/outputsystem 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memory module单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requiremcnt Planning物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头。
机械类英语词汇中英文对照
cosmic宇宙的，全世界的，广大无边的
profile剖面，侧面,外形，轮廓
cotter pin开口销，开尾销
projection投影
counterbore镗沉头孔
projection突出，凸起部分
countersink钻沉头孔
propel推进，驱使
cover up包裹，隐藏，掩盖
moulding成形
castingforging die铸，锻模
mould模具，模塑,压模
catalogue产品样本，目录
muffler（silencer）消声器
catalytic converter催化转化器
multi—disciplinary（有关）多种学科的
category种类，逻辑范畴
multifunction多功能
rationale基本原理,理论基础,原理的阐述
deficiency缺乏，不足
rattle硬物质的撞击声
delegation代表团
reagent反应物，反应力,试剂
deliberately有目的的,故意的
ream铰孔
delicately shaped parts外形精致的零件
recapitulate扼要重述，概括，重现，再演
denote指示，表示，概述
recognition识别
designate指明，指出
recovery回复
detail drawing零件图
recrystallization再结晶
detriment损害，不利
redundant多余的，冗余的
assembly组合，装配,部件，汇编
atmospheric大气的，空气的
机械专业英语词汇中英文对照
机械专业英语词汇中英文对照第一篇：机械专业英语词汇中英文对照机床 machine tool金属工艺学 technology of metals刀具 cutter摩擦 friction联结link传动 drive/transmission轴 shaft弹性 elasticity频率特性 frequency characteristic误差 error响应 response定位 allocation机床夹具 jig动力学 dynamic运动学 kinematic静力学static分析力学analyse mechanics拉伸pulling压缩hitting剪切shear扭转 twist弯曲应力 bending stress强度 intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor几何形状geometrical精度precision正弦形的 sinusoid交流电路 AC circuit机械加工余量 machining allowance变形力 deforming force变形 deformation应力 stress硬度 rigidity热处理 heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization电路 circuit半导体元件 semiconductor element反馈 feedback发生器 generator直流电源 DC electrical source门电路 gate circuit逻辑代数 logic algebra外圆磨削 external grinding内圆磨削 internal grinding平面磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞刀reamer螺纹加工 thread processing螺钉 screw铣削 mill铣刀 milling cutter功率 power工件 workpiece齿轮加工 gear mechining齿轮 gear主运动 main movement主运动方向 direction of main movement进给方向 direction of feed进给运动 feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向 direction of resultantmovement of cutting切削深度 cutting depth前刀面 rake face 刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe钻削镗削 bore车削 turning磨床 grinder基准 benchmark钳工 locksmith 锻 forge压模 stamping焊 weld拉床 broaching machine拉孔 broaching装配 assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure稳定性 stability介质 medium液压驱动泵 fluid clutch液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数safty factor可靠性reliability螺纹thread螺旋helix 键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring 制动器 arrester brake十字结联轴节 crosshead联轴器 coupling 链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor第二篇：机械专业论文中英文对照Gearbox Noise Correlation with Transmission Error and Influence of Bearing PreloadABSTRACT The five appended papers all deal with gearbox noise and vibration.The first paper presents a review of previously published literature on gearbox noise and vibration.The second paper describes a test rig that was specially designed and built for noise testing of gears.Finite element analysis was used to predict the dynamic properties of the test rig, and experimental modal analysis of the gearbox housing was used to verify the theoretical predictions of natural frequencies.In the third paper, the influence of gear finishing method and gear deviations on gearbox noise is investigated in what is primarily an experimental study.Eleven test gear pairs were manufactured using threedifferent finishing methods.Transmission error, which is considered to be an important excitation mechanism for gear noise, was measured as well as predicted.The test rig was used to measure gearbox noise and vibration for the different test gear pairs.The measured noise and vibration levels were compared with the predicted and measured transmission error.Most of the experimental results can be interpreted in terms of measured and predicted transmission error.However, it does not seem possible to identify one single parameter,such as measured peak-to-peak transmission error, that can be directly related to measured noise and vibration.The measurements also show that disassembly and reassembly of the gearbox with the same gear pair can change the levels of measured noise and vibration considerably.This finding indicates that other factors besides the gears affect gear noise.In the fourth paper, the influence of bearing endplay or preload on gearbox noise and vibration is investigated.Vibration measurements were carried out at torque levels of 140 Nm and 400Nm, with 0.15 mm and 0 mm bearing endplay, and with 0.15 mm bearing preload.The results show that the bearing endplay and preloadinfluence the gearbox vibrations.With preloaded bearings, the vibrations increase at speeds over 2000 rpm and decrease at speeds below 2000 rpm, compared with bearings with endplay.Finite element simulations show the same tendencies as the measurements.The fifth paper describes how gearbox noise is reduced by optimizing the gear geometry for decreased transmission error.Robustness with respect to gear deviations and varying torque is considered in order to find a gear geometry giving low noise in an appropriate torque range despite deviations from the nominal geometry due to manufacturingtolerances.Static and dynamic transmission error, noise, and housing vibrations were measured.The correlation between dynamic transmission error, housing vibrations and noise was investigated in speed sweeps from 500 to 2500 rpm at constant torque.No correlation was found between dynamic transmission error and noise.Static loaded transmission error seems to be correlated with the ability of the gear pair to excite vibration in the gearbox dynamic system.Keywords: gear, gearbox, noise, vibration, transmission error, bearing preload.ACKNOWLEDGEMENTS This work was carried out at Volvo Construction Equipment in Eskilstuna and at the Department of Machine Design at the Royal Institute of Technology(KTH)in Stockholm.The work was initiated by Professor Jack Samuelsson(Volvo and KTH), Professor Sören Andersson(KTH), and rs Bråthe(Volvo).The financial support of the Swedish Foundation for Strategic Research and the Swedish Agency for Innovation Systems –VINNOVA –is gratefully acknowledged.Volvo Construction Equipment is acknowledged for giving me the opportunity to devote time to this w ork.Professor Sören Andersson is gratefully acknowledged for excellent guidance and encouragement.I also wish to express my appreciation to my colleagues at the Department of Machine Design, and especially to Dr.Ulf Sellgren for performing simulations and contributing to the writing of Paper D, and Dr.Stefan Björklund for performing surface finish measurements.The contributions to Paper C by Dr.Mikael Pärssinen are highly appreciated.All contributionsto this work by colleagues at Volvo are gratefully appreciated.1 INTRODUCTION 1.1 Background Noise is increasingly considered an environmental issue.This belief is reflected in demands forlower noise levels in many areas of society, including the working environment.Employees spend a lot of time in this environment and noise can lead not only to hearing impairment but also to decreased ability to concentrate, resulting in decreased productivity and an increased risk of accidents.Quality, too, has become increasingly important.The quality of a product can be defi ned as its ability to fulfill customers’ demands.These demands often change over time, and the best competitors in the market will set the standard.Noise concerns are also expressed in relation to construction machinery such as wheel loaders and articulated haulers.The gearbox is sometimes the dominant source of noise in these machines.Even if the gear noise is not the loudest source, its pure high frequency tone is easily distinguished from other noise sources and is often perceived as unpleasant.The noise creates an impression of poor quality.In order not to be heard, gear noise must be at least 15 dB lower than other noise sources, such as engine noise.1.2 Gear noise This dissertation deals with the kind of gearbox noise that is generated by gears under load.This noise is often referred to as “gear whine” and consists mainly of pure tones at high frequencies corresponding to the gear mesh frequency and multiples thereof, which are known as harmonics.A tone with the same frequency as the gear mesh frequency is designated the gear mesh harmonic, a tone with a frequency twice the gear mesh frequency is designated the second harmonic, and so on.The term “gear mesh harmonics” refers to all multiples of the gear mesh frequency.Transmission error(TE)is considered an important excitation mechanism for gear whine.Welbourn [1] defines transmission error as “the difference between the actual position of the output gear and the position itwould occupy if the gear drive were perfectly conjugate.” Transmission error may be expressed as angular displacement or as linear displacement at the pitch point.Transmission error is caused by deflections, geometric errors, and geometric modifications.In addition to gear whine, other possible noise-generating mechanisms in gearboxes include gear rattle from gears running against each other without load, and noise generated by bearings.In the case of automatic gearboxes, noise can also be generated by internal oil pumps and by clutches.None of these mechanisms are dealt with in this work, and from now on “gear noise” or “gearbox noise” refers to “gear whine”.MackAldener [2] describes the noise generation process from a gearbox as consisting of three parts: excitation, transmission, and radiation.The origin of the noise is the gear mesh, in which vibrations are created(excitation), mainly due to transmission error.The vibrations are transmitted via the gears, shafts, and bearings to the housing(transmission).The housing vibrates, creating pressure variations in the surrounding air that are perceived as noise(radiation).Gear noise can be affected by changing any one of these three mechanisms.This dissertation deals mainly with excitation, but transmission is also discussed in the section of the literature survey concerning dynamic models, and in the modal analysis of the test gearbox in Paper B.Transmission of vibrations is also investigated in Paper D, which deals with the influence of bearing endplay or preload on gearbox noise.Differences in bearing preload influence a bearing’s dynamic p roperties like stiffness and damping.These properties also affect the vibration of the gearbox housing.1.3 Objective The objective of this dissertation is to contribute to knowledge about gearbox noise.The following specific areas willbe the focus of this study: 1.The influence of gear finishing method and gear modifications and errors on noise and vibration from a gearbox.2.The correlation between gear deviations, predicted transmission error, measured transmission error, and gearbox noise.3.The influence of bearing preload on gearbox noise.4.Optimization of gear geometry for low transmission error, taking into consideration robustness with respect to torque and manufacturing tolerances.2 AN INDUSTRIAL APPLICATION −TRANSMISSION NOISE REDUCTION 2.1 Introduction This section briefly describes the activities involved in reducing gear noise from a wheel loader transmission.The aim is to show how the optimization of the gear geometry described in Paper E is used in an industrial application.The author was project manager for the “noise work team” and performed the gear optimization.One of the requirements when developing a new automatic power transmission for a wheel loader was improving the transmission gear noise.The existing power transmission was known to be noisy.When driving at high speed in fourth gear, a high frequency gear-whine could be heard.Thus there were now demands for improved sound quality.The transmission is a typical wheel loader power transmission, consisting of a torque converter, a gearbox with four forward speeds and four reverse speeds, and a dropbox partly integrated with the gearbox.The dropbox is a chain of four gears transferring the powerto the output shaft.The gears are engaged by wet multi-disc clutches actuated by the transmission hydraulic and control system.2.2 Gear noise target for the new transmission Experience has shown that the high frequency gear noise should be at least 15 dB below other noise sources such as the engine in order not to be perceived as disturbing or unpleasant.Measurements showedthat if the gear noise could be decreased by 10 dB, this criterion should be satisfied with some margin.Frequency analysis of the noise measured in the driver's cab showed that the dominant noise from the transmission originated from the dropbox gears.The goal for transmission noise was thus formulated as follows: “The gear noise(sound pressure level)from the dropbox gears in the transmission should be decreased by 10 dB compared to the existing transmission in order not to be perceived as unpleasant.It was assumed that it would be necessary to make changes to both the gears and the transmission housing in order to decrease the gear noise sound pressure level by 10 dB.2.3 Noise and vibration measurements In order to establish a reference for the new transmission, noise and vibration were measured for the existing transmission.The transmission is driven by the same type of diesel engine used in a wheel loader.The engine and transmission are attached to the stand using the same rubber mounts that are used in a wheel loader in order to make the installation as similar as possible to the installation in a wheel loader.The output shaft is braked using an electrical brake.2.4 Optimization of gears Noise-optimized dropbox gears were designed by choosing macro-and microgeometries giving lower transmission error than the original(reference)gears.The gear geometry was chosen to yield a low transmission error for the relevant torque range, while also taking into consideration variations in the microgeometry due to manufacturing tolerances.The optimization of one gear pair is described in more detail in Paper E.Transmission error is considered an important excitation mechanism for gear whine.Welbourn [1] defines it as “the difference between the actual position of the output gear and the position it wouldoccupy if the gear drive were perfectly conjugate.” In this project the aim was to reduce the maximum predicted transmission error amplitude at gear mesh frequency(first harmonic of gear mesh frequency)to less than 50% of the value for the reference gear pair.The first harmonic of transmission error is the amplitude of the part of the total transmission error that varies with a frequency equal to the gear mesh frequency.A torque range of 100 to 500 Nm was chosen because this is the torque interval in which the gear pair generates noise in its design application.According to Welbourn [1], a 50% reduction in transmission error can be expected to reduce gearbox noise by 6 dB(sound pressure level, SPL).Transmission error was calculated using the LDP software(Load Distribution Program)developed at the Gear Laboratory at Ohio State University [3].The “optimization” was not strictly mathematical.The design was optimized by calculating the transmission error for different geometries, and then choosing a geometry that seemed to be a good compromise, considering not only the transmission error, but also factors such asstrength, losses, weight, cost, axial forces on bearings, and manufacturing.When choosing microgeometric modifications and tolerances, it is important to take manufacturing options and cost into consideration.The goal was to use the same finishing method for the optimized gears as for the reference gears, namely grinding using a KAPP VAS 531 and CBN-coated grinding wheels.For a specific torque and gear macrogeometry, it is possible to define a gear microgeometry that minimizes transmission error.For example, at no load, if there are no pitch errors and no other geometrical deviations, the shape of the gear teeth should be true involute, withoutmodifications like tip relief or involute crowning.For a specific torque, the geometry of the gear should be designed in such a way that it compensates for the differences in deflection related to stiffness variations in the gear mesh.However, even if it is possible to define the optimal gear microgeometry, it may not be possible to manufacture it, given the limitations of gear machining.Consideration must also be given to how to specify the gear geometry in drawings and how to measure the gear in an inspection machine.In many applications there is also a torque range over which the transmission error should be minimized.Given that manufacturing tolerances are inevitable, and that a demand for smaller tolerances leads to higher manufacturing costs, it is important that gears be robust.In other words, the important characteristics, in this case transmission error, must not vary much when the torque is varied or when the microgeometry of the gear teeth varies due to manufacturing tolerances.LDP [3] was used to calculate the transmission error for the reference and optimized gear pair at different torque levels.The robustness function in LDP was used to analyze the sensitivity to deviations due to manufacturing tolerances.The “min, max, level” method involves assigning three levels to each parameter.2.5 Optimization of transmission housing Finite element analysis was used to optimize the transmission housing.The optimization was not performed in a strictly mathematical way, but was done by calculating the vibration of the housing for different geometries and then choosing a geometry that seemed to be a good compromise.Vibration was not the sole consideration, also weight, cost, available space, and casting were considered.A simplified shell element model was used for the optimization to decrease computational time.Thismodel was checked against a more detailed solid element model of the housing to ensure that the simplification had not changed the dynamic properties too much.Experimental modal analysis was also used to find the natural frequencies of the real transmission housing and to ensure that the model did not deviate too much from the real housing.Gears shafts and bearings were modeled as point masses and beams.The model was excited at the bearing positions by applying forces in the frequency range from 1000 to 3000 Hz.The force amplitude was chosen as 10% of the static load from the gears.This choice could be justified because only relative differences are of interest, not absolute values.The finite element analysis was performed by Torbjörn Johansen at Volvo Technology.The author’s contribution was the evaluation of the results of different housing geometries.A number of measuring points were chosen in areas with high vibration velocities.At each measuring point the vibration response due to the excitation was evaluated as a power spectral density(PSD)graph.The goal of the housing redesign was to decrease the vibrations at all measuring points in the frequency range 1000 to 3000 Hz.2.6 Results of the noise measurements The noise and vibration measurements described in section 2.3 were performed after optimizing the gears and transmission housing.The total sound power level decreased by 4 dB.2.7 Discussion and conclusions It seems to be possible to decrease the gear noise from a transmission bydecreasing the static loaded transmission error and/or optimizing the housing.In the present study, it is impossible to say how much of the decrease is due to the gear optimization and how much to the housing optimization.Answering this question would have required at least one more noisemeasurement, but time and cost issues precluded this.It would also have been interesting to perform the noise measurements on a number of transmissions, both before and after optimizing the gears and housing, in order to determine the scatter of the noise of the transmissions.Even though the goal of decreasing the gear noise by 10 dB was not reached, the goal of reducing the gear noise in the wheel loader cab to 15 dB below the overall noise was achieved.Thus the noise optimization was successful.3 SUMMARY OF APPENDED PAPERS 3.1 Paper A: Gear Noise and Vibration – A Literature Survey This paper presents an overview of the literature on gear noise and vibration.It is divided into three sections dealing with transmission error, dynamic models, and noise and vibration measurement.Transmission error is an important excitation mechanism for gear noise and vibration.It is defined as “the difference between the actual position of the output gear and the position it would occupy if the gear drive were perfectly conjugate” [1].The literature survey revealed that while most authors agree that transmission error is an important excitation mechanism for gear noise and vibration, it is not the only one.Other possible time-varying noise excitation mechanisms include friction and bending moment.Noise produced by these mechanisms may be of the same order of magnitude as that produced by transmission error, at least in the case of gears with low transmission error [4].The second section of the paper deals with dynamic modeling of gearboxes.Dynamic models are often used to predict gear-induced vibrations and investigate the effect of changes to the gears, shafts, bearings, and housing.The literature survey revealed that dynamic models of a system consisting of gears, shafts, bearings, and gearbox casing can be useful in understanding and predicting thedynamic behavior of a gearbox.Forrelatively simple gear systems, lumped parameter dynamic models with springs, masses, and viscous damping can be used.For more complex models that include such elements as the gearbox housing, finite element modeling is often used.The third section of the paper deals with noise and vibration measurement and signal analysis, which are used when experimentally investigating gear noise.The survey shows that these are useful tools in experimental investigation of gear noise because gears create noise at specific frequencies related to the number of teeth and the rotational speed of the gear.3.2 Paper B: Gear Test Rig for Noise and Vibration Testing of Cylindrical Gears Paper B describes a test rig for noise testing of gears.The rig is of the recirculating power type and consists of two identical gearboxes, connected to each other with two universal joint shafts.Torque is applied by tilting one of the gearboxes around one of its axles.This tilting is made possible by bearings between the gearbox and the supporting brackets.A hydraulic cylinder creates the tilting force.Finite element analysis was used to predict the natural frequencies and mode shapes for individual components and for the complete gearbox.Experimental modal analysis was carried out on the gearbox housing, and the results showed that the FE predictions agree with the measured frequencies(error less than 10%).The FE model of the complete gearbox was also used in a harmonic response analysis.A sinusoidal force was applied in the gear mesh and the corresponding vibration amplitude at a point on the gearbox housing was predicted.3.3 Paper C: A Study of Gear Noise and Vibration Paper C reports on an experimental investigation of the influence of gear finishing methods and gear deviations on gearbox noise and vibration.Test gears weremanufactured using three different finishing methods and with different gear tooth modifications and deviations.T able3.3.1 gives an overview of the test gear pairs.The surface finishes and geometries of the gear tooth flanks were measured.Transmission error was measured using a single flank gear tester.LDP software from Ohio State University was used for transmission error computations.The test rig described in Paper B was used to measure gearbox noise and vibration for the different test gear pairs.The measurements showed that disassembly and reassembly of the gearbox with the same gear pair might change the levels of measured noise and vibration.The rebuild variation was sometimes of the same order of magnitude as the differences between different tested gear pairs, indicating that other factors besides the gears affect gear noise.In a study of the influence of gear design on noise, Oswald et al.[5] reported rebuild variations of the same order of magnitude.Different gear finishing methods produce different surface finishes and structures, as well as different geometries and deviations of the gear tooth flanks, all of which influence the transmission error and thus the noise level from a gearbox.Most of the experimental results can be explained in terms of measured and computed transmission error.The relationship between predicted peak-to-peak transmission error and measured noise at a torque level of 500 Nm is shown in Figure 3.3.1.There appears to be a strong correlation between computed transmission error and noise for all cases except gear pair K.However, this correlation breaks down in Figure 3.3.2, which shows the relationship between predicted peak to peak transmission error and measured noise at a torque level of 140 Nm.The final conclusion is that it may not be possible to identify a single parameter, such as peak-to-peak transmissionerror, that can be directly related to measured noise and vibration.3.4 Paper D: Gearbox Noise and Vibration −Influence of Bearing Preload The influence of bearing endplay or preload on gearbox noise and vibrations is investigated in Paper D.Measurements were carried out on a test gearbox consisting of a helical gear pair, shafts, tapered roller bearings, and a housing.Vibration measurements were carried out at torque levels of 140 Nm and 400 Nm with 0.15 mm and 0 mm bearing endplay and with 0.15 mm bearing preload.The results shows that the bearing endplay or preload influence gearbox pared with bearingswith endplay, preloaded bearings show an increase in vibrations at speeds over 2000 rpm and a decrease at speeds below 2000 rpm.Figure 3.4.1 is a typical result showing the influence of bearing preload on gearbox housing vibration.After the first measurement, the gearbox was not disassembled or removed from the test rig.Only the bearing preload/endplay was changed from 0 mm endplay/preload to 0.15 mm preload.Therefore the differences between the two measurements are solely due to different bearing preload.FE simulations performed by Sellgren and Åkerblom [6] show the same trend as the measurements here.For the test gearbox, it seems that bearing preload, compared with endplay, decreased the vibrations at speeds below 2000 rpm and increased vibrations at speeds over 2000 rpm, at least at a torque level of 140 Nm.3.5 Paper E: Gear Geometry for Reduced and Robust Transmission Error and Gearbox Noise In Paper E, gearbox noise is reduced by optimization of gear geometry for decreased transmission error.The optimization was not performed strictly mathematically.It was done by calculating the transmission errorfor different geometries and then choosing a geometry that seemed to be a good compromise considering not only the transmission error, but also other important characteristics.Robustness with respect to gear deviations and varying torque was considered in order to find gear geometry with low transmission error in the appropriate torque range despite deviations from the nominal geometry due to manufacturing tolerances.Static and dynamic transmission error as well as noise and housing vibrations were measured.The correlation between dynamic transmission error, housing vibrations, and noise was investigated in a speed sweep from 500 to 2500 rpm at constant torque.No correlation was found between dynamic transmission error and noise.4 DISCUSSION AND CONCLUSIONS Static loaded transmission error seems to be strongly correlated to gearbox noise.Dynamic transmission error does not seem to be correlated to gearbox noise in speed 第三篇：机械名称中英文对照一、除大块机Eliminates the bulk machine二、齿型筛分除杂物机The screening and eliminates the sundry goods machine三、振动煤箅Vibration Coal Grate四、滚轴筛Roller Screen五、滚筒筛Trommel Screen六、振动概率筛Vibration Probability Screen七、减振平台Antivibration Platform八、布料器Distributing Device九、皮带机头部伸缩装置Conveyer Belt Telescopiform Device十、胶带给料机Belt Feeder十一、往复式给料机Reciprocating Feeder十二、振动给煤机Vibrator Feeder。
常用机械专业术语中英文对照
常用机械专业术语中英文对照机械工程是一个涵盖广泛的领域，其中包含了许多复杂的专业术语。
对于学习和工作在机械领域的人而言，掌握这些术语是非常重要的。
在此，我们将通过对常用机械专业术语的中英文对照进行分析和解释，为您提供帮助。
1. 传动系统：Transmission system2. 机械零件：Mechanical parts3. 摩擦力：Friction force4. 机械加工：Mechanical processing5. 各向同性：Isotropy6. 焊接：Welding7. 机械设计：Mechanical design8. 电机：Electric motor9. 压力传感器：Pressure sensor10. 材料力学：Material mechanics11. 钢铁材料：Steel materials12. 运动控制：Motion control13. 热处理：Heat treatment14. 机械系统：Mechanical system15. 变形：Deformation16. 自适应控制：Adaptive control17. 流体力学：Fluid mechanics18. 微机电系统：Micro-electromechanical systems19. 工业机器人：Industrial robot20. CNC加工：CNC machining以上就是常用机械专业术语的中英文对照。
这些术语是机械领域中非常重要的一部分，他们涵盖了机械材料、流体力学、控制系统和加工过程等领域。
对于机械工程师来说，能够正确地使用这些术语可以帮助他们更好地理解机械原理和操作方法。
此外，在不同的国家和地区，机械专业术语的使用可能会有所不同。
因此，在国际贸易和国际交流中，了解各种语言和文化的机械术语是非常有益的。
最后，学习这些机械专业术语需要具备一定的专业知识和背景知识。
因此，如果您想要更深入地了解机械领域，我们建议您课程或学习机械工程相关的教材。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics。
human engineering 人体尺寸 human dimension人体测量学 anthropometry。
anthropometrics 刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角尺 set square三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰?胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellacspanner士巴拿；扳手大芯夹板；宽条芯夹板 blockboard。
solid corestock-laminated board大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB) 小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench。
working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw。
hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal 不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU) 中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF) 中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive propertiesscribing gouge内圆弯凿内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies 分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider。
voltage divider 隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cutchip切屑；碎屑．切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off 切断工具 parting tool勾；勾脚 hook勾刀；胶片?刀 plastic cutter 化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier 反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vicehandle手柄．手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine 支柱；支撑物 strut支架；支座 support支点 fulcrum。
pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chiselwood木．木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe。
woodworking lathe 木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB) polyester resin水晶胶；聚酯树脂．水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining 火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch五画丙烯?丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fittingcam drive凸轮传动．凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining 半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck ) four-centre method绘图(四圆心法．外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon。