齿轮参数中英文对照
齿轮参数中英文对照
齿轮参数中英文对照Gear Parameters 齿轮参数1. Pitch Circle Diameter (PCD) 中心圆直径2. Module 压力角Module refers to the ratio of the pitch circle diameter to the number of teeth. It determines the size of the gear teeth and is expressed in millimeters. The module is an essential parameter for gear manufacturing and design.3. Pressure Angle 压力角The pressure angle is the angle between the line of action and a line tangent to the pitch circle. It affects the gear's performance, including its load-carrying capacity and efficiency.4. Number of Teeth 齿数The number of teeth is the total count of teeth on a gear.It plays a crucial role in determining the gear's size,rotational speed, and torque ratio.5. Circular Pitch 圆距The circular pitch is the distance between corresponding points on adjacent gear teeth. It is usually measured along the pitch circle and is represented in millimeters.6. Face Width 面宽The face width refers to the length of the gear teeth along the axis of rotation. It is an essential parameter for ensuring proper load distribution and tooth strength.7. Helix Angle 螺旋角The helix angle is the angle formed between the helix and a plane perpendicular to the gear axis. It determines thedirection of the helical gear's tooth spiral.8. Module Angle 模仰角The module angle is the angle between the line of action and a line tangent to the helix angle. It is a critical parameterfor helical gears.9. Helix Lead 螺旋铅距10. Backlash 间隙Backlash is the amount of clearance or play between the mating gears when they are not in contact. It affects the transmission accuracy and must be carefully controlled in gear design.11. Addendum 圆顶The addendum is the radial distance between the pitch circle and the outermost point on the gear tooth. It ensures proper engagement between gears.12. Dedendum 圆谷The dedendum is the radial distance between the pitch circle and the innermost point on the gear tooth. It providessufficient space for the mating gear's teeth.13. Dedendum Angle 谷角The dedendum angle is the angle between the dedendum and a radial line from the gear center. It affects the gear'sdurability and strength.14. Working Depth 有效厚度The working depth is the radial distance between the addendum and dedendum. It plays a crucial role in determining the gear's load-carrying capacity and strength.15. Pitch Diameter 齿顶直径The pitch diameter is the diameter of the pitch circle. It is typically used in gear calculations.。
[指南]齿轮参数中英对照
![[指南]齿轮参数中英对照](https://img.taocdn.com/s3/m/a5df78741fb91a37f111f18583d049649b660ee4.png)
齿轮基本术语(中英文对照)齿轮 Toothed gear；Gear齿轮副 Gear pair平行轴齿轮副 Gear pair with parallel axes相交轴齿轮副 Gear pair with intersecting axes 齿轮系 Train of gears行星齿轮系 Planetary gear train齿轮传动 Gear drive；Gear transmission配对齿轮 Mating gears小齿轮 Pinion大齿轮 Wheel；Gear主动齿轮 Driving gear从动齿轮 Driven gear行星齿轮 Planet gear行星架 Planet carrier太阳轮 Sun gear内齿圈 Ring gear；Annulus gear外齿轮 External gear内齿轮 Internal gear中心距 Centre distance轴交角 Shaft angle连心线 Line of centres减速齿轮副 Speed reducing gear pair增速齿轮副 Speed increasing gear pair齿数比 Gear ratio传动比 Transmission ratio轴平面 Axial plane基准平面 Datum plane节平面 Pitch plane端平面 Transverse plane法平面 Normal plane分度曲面 Reference surface节曲面 Pitch surface齿顶曲面 Tip surface齿根曲面 Root surface基本齿廓 Basic tooth profile基本齿条 Basic rack产形齿条 Counterpart rack产形齿轮 Generating gear of a gear产形齿面 Generating flank基准线 Datum line轮齿 Gear teeth；Tooth齿槽 Tooth space右旋齿 Right-hand teeth左旋齿 Left-hand teeth变位齿轮 Gears with addendum modification；X-gears高度变位圆柱齿轮副 X-gear pair with reference centre distance 角度变位圆柱齿轮副 X-gear pair with modified centre distance 高度变位锥齿轮副 X-gear pair without shaft angle modification 角度变位圆柱齿轮副 X-gear pair with shaft angle modification 变位系数 Modification coefficient变位量 Addendum modification径向变位系数 Addendum modification coefficient中心距变位系数 Centre distance modification coefficient圆柱齿轮 Cylindrical gear顶圆 Tip circle根圆 Root circle齿距 Pitch齿距角 Angular pitch公法线长度 Base tangent length分度圆直径 Reference diameter节圆直径 Pitch diameter基圆直径 Base diameter顶圆直径 Tip diameter根圆直径 Root diameter齿根圆角半径 Fillet radius齿高 Tooth depth工作高度 Working depth齿顶高 Addendum齿根高 Dedendum弦齿高 Chordal height固定弦齿高 Constant chord height齿宽 Facewidth有效齿宽 Effective facewidth端面齿厚 Transverse tooth thickness法向齿厚 Normal tooth thickness端面基圆齿厚 Transverse base thickness法向基圆齿厚 Normal base thickness端面弦齿厚 Transverse chordal tooth thickness固定弦齿厚 Constant chord端面齿顶厚 Crest width法向齿顶厚 Normal crest width端面齿槽宽 Transverse spacewidth法向齿槽宽 Normal spacewidth齿厚半角 Tooth thickness half angle槽宽半角 Spacewidth half angle压力角 Pressure angle齿形角 Nominal pressure angle圆弧圆柱蜗杆 Arc-contact worm；hollow flank worm；ZC-worm直廓环面蜗杆 Enveloping worm with straight line grneratrix；TA worm平面蜗杆 Planar worm wheel；P-worm wheel平面包络环面蜗杆 Planar double enveloping worm；TP-worm平面二次包络蜗杆 Planar double-enveloping worm wheel；TP-worm wheel锥面包络环面蜗杆 Toroid enveloping worm wheel；TK-worm wheel 渐开线包络环面蜗杆 Toroid enveloping worm hich involute holicoid generatrix；TI-worm锥蜗杆 Spiroid锥蜗轮 Spiroid gear锥蜗杆副 Spiroid gear pair中平面 Mid-plane长幅内摆线 Prolate hypocycloid短幅内摆线 Curtate hypocycloid渐开线 Involute；Involute to a circle延伸渐开线 Prolate involute缩短渐开线 Curtate involute球面渐开线 Spherical involute渐开螺旋面 Involute helicoid阿基米德螺旋面 Screw helicoid球面渐开螺旋面 Spherical involute helicoid圆环面 Toroid圆环面的母圈 Generant of the toroit圆环面的中性圈 Middle circle of the toroid圆环面的中间平面 Middle-plane of the toroid圆环面的内圈 Inner circle of the toroid啮合干涉 Meshing interference切齿干涉 Cutter interference齿廓修型 Profile modification；Profile correction修缘 Tip relief修根 Root relief齿向修形 Axial modification；Longitudinal correction齿端修薄 End relief鼓形修整 Crowning鼓形齿 Crowned teeth挖根 Undercut瞬时轴 Instantaneous axis瞬时接触点 Point of contact瞬时接触线 Line of contact端面啮合线 Transverse path of contact啮合曲面 Surface of action啮合平面 Plane of action啮合区域 Zone of action总作用弧 Total arc of transmission端面作用弧 Transverse arc of transmission 纵向作用弧 Overlap arc总作用角 Total angle of transmission端面作用角 Transverse angle of transmission 纵向作用角 Overlap angle总重合度 Total contact ratio端面重合度 Transverse ratio纵向重合度 Overlap ratio标准齿轮 Standard gears非变位齿轮 X-gero gear标准中心距 Referencr centre distance名义中心距 Nominal centre distance分度圆柱面 Reference cylinder节圆柱面 Pitch cylinder基圆柱面 Basic cylinder齿顶圆柱面 Tip cylinder齿根圆柱面 Root cylinder节点 Pitch point节线 Pitch line分度圆 Reference circle节圆 Pitch circle基圆 Basic circle定位面 Locating face外锥距 Outer cone distance内锥距 Inner cone distance中点锥距 Mean cone distance背锥距 Back cone distance安装距 Locating distance轮冠距 Tip distance；crown to back冠顶距 Apex to crown偏置距 Offset齿线偏移量 Offset of tooth trace分锥角 Reference cone angle节锥角 Pitch cone angle顶锥角 Tip angle根锥角 Root angle背锥角 Back cone angle齿顶角 Addendum angel齿根角 Dedendum angle任意点压力角 Pressure angle at a point任意点螺旋角 Spiral angle at a point中点螺旋角 Mean spiral angle大端螺旋角 Outer spiral angle小端螺旋角 Inner spiral angle蜗杆 Worm蜗轮 Worm wheel蜗杆副 Worm gear pair圆柱蜗杆 Cylindrical worm圆柱蜗杆副 Cylindrical worm pair环面蜗杆 Enveloping worm环面蜗杆副 Enveloping worm pair阿基米德蜗杆 Straight sided axial worm；ZA-worm 渐开线蜗杆 Involute helicoid worm；ZI-worm法向直廓蜗杆 Straight sided normal worm；ZN-worm 锥面包络圆柱蜗杆 Milled helicoid worm；ZK-worm 椭圆齿轮 Elliptical gear非圆齿轮副 Non-circular gear pair圆柱针轮副 Cylindsical lantern pinion and wheel 针轮 Cylindsical tan tein gear ；pin-wheel谐波齿轮副 Harmoric gear drive波发生器 Wave generator柔性齿轮 Flexspine刚性齿轮 Circular spline非圆齿轮 Non-circular gear分度圆环面 Reference tosoid。
齿轮参数中英文对照
A.1. abrasive tooth wear 齿面研磨磨损2. absolute tangential velocity 绝对切向速度3. accelerometer 加速表4. addendum 齿顶高5. addendum angle 齿顶角6. addendum circle 齿顶圆7. addendum surface 上齿面8. adhesive wear 粘着磨损9. adjustability 可调性10. adjustability coefficients 可调系数11. adjusting wedge 圆盘端铣刀的可调型楔块12. allowable stress 允许应力13. alternate blade cutter 双面刀盘14. angular backlash 角侧隙15. angular bevel gears 斜交锥齿轮16. angular displacement 角移位17. angular pitch 齿端距18. angular testing machine 可调角度试验机19. approach action 啮入20. arbor 心轴21. arbor distance 心轴距22. arc of approach 啮入弧23. arc of recess 啮出弧24. attraction 收紧25. average cutter diameter 平均刀尖直径26. axial displacement 轴向位移27. axial factor 轴向系数28. axial locating surface 轴向定位面29. axial pitch 轴向齿距30. axial plane 轴向平面31. axial rakeangle 轴向前角32. axial thrust 轴向推力33. axle testing machine 传动桥试验机B.1．back angle 背锥角2．Back angle distance 背角距（在背锥母线方向）3．Back cone 背锥4．Back cone distance 背锥距5．Back cone element 背锥母线6．Backlash 侧隙7．Backlash tolerance 侧隙公差8．Backlash variation 侧隙变量9．Backlash variation tolerance 侧隙变量公差10．Bandwidth 频带宽11．Base circle 基圆12．Base diameter 基圆直径13．Base pitch 基节14．Base radius 基圆半径15．Base spiral angle 基圆螺旋角16．Basic rack 基本齿条17．Bearing 轴承18．Bearing preload 轴承预负荷19．Bearing spacing／spread 轴承间距20．Bending fatigue 弯曲疲劳21．Bending stress 弯曲应力22．Bevel gears 锥齿轮23．Bias 对角接触24．Bias in 内对角接触25．Bias out 外对角接触26．Blade angle 刀齿齿廓角27．Blade edge radius 刀尖圆角半径28．Blade letter 刀尖凸角代号29．Blade life 刀尖寿命30．Blade point width 刀顶宽31．Blank offset 毛坯偏置距32．Bland position 毛坯位置33．Bottom land 齿槽底面34．Boundary lubrication 界面润滑35．Breakage 破裂36．Bridged contact pattern 桥型接触斑点37．Broach 拉刀38．Burnishing 挤齿C．1. Case crushing 齿面塌陷2. CBN 立方氮化硼3. chamfer 倒角4. chordal addendum 弦齿高5. chordal thickness 弦齿厚6. chuck 卡盘7. circular broach 圆拉刀8. circular face-mill 圆盘端面铣刀9. circular peripheral-mill 圆盘铣刀10. circular pitch 周节11. circular thickness 弧齿厚12. circular thickness factor 弧齿厚系数13. clearance 顶隙14. clearance angle 后角15. coarse pitch 大节距16. coast side 不工作齿侧17. combination 组合18. combined preload 综合预负荷19. complementary crown gears 互补冠状齿轮20. completing cycle 全工序循环21. composite action 双面啮合综合检验误差22. compressive stress 压应力23. concave side 凹面24. concentricity 同心度25. concentricity tester 同心度检查仪26. cone distance 锥距27. cone element 锥面母线28. conformal surfaces 共型表面29. coniskoid 斜锥齿轮30. conjugate gears 共轭齿轮31. conjugate racks 共轭齿条32. contact fatigue 接触疲劳33. contact norma 接触点法线34. contact pattern (tooth contact pattern) 轮齿接触斑点35. contact ratio 重合度36. contact stress 接触应力37. continuous index 连续分度38. control gear 标准齿轮，检验用齿轮39. convex side 凸面40. coolant 冷却液41. corrosive wear 腐蚀性磨损42. corrugated tool 阶梯刨刀43. counter forma surfaces 反法向表面44. cradle 摇台45. cradle test roll 摇台角46. cross 大小端接触47. crossing point 交错点48. crown 齿冠49. crown circle 锥齿轮冠圆50. crowned teeth 鼓形齿51. crown gear 冠轮52. crown to back （轮冠距）轮冠至安装定位面距离53. crown to crossing point 轮冠至相错点距离54. cutter 刀盘55. cutter axial 刀盘的轴向位置56. cutter axial plane 刀盘轴向平面57. cutter axis 刀盘轴线58. cutter diameter 刀盘直径59. cutter edge radius 刀刃圆角半径60. cutter head 刀盘体61. cutter number 刀号62. cutter parallel 刀盘平垫片63. cutter point diameter 刀尖直径64. cutter point radius 刀尖半径65. cutter point width 刀顶距66. cutter spindle 刀盘主轴67. cutter spindle rotation angle 刀盘主轴转角68. cutting distance 切齿安装距69. C.V. testing mashing 常速试验机70. cyclex 格里森粗铣精拉法圆盘端铣刀71. cylindrical gears 圆柱齿轮D.1．Datum tooth 基准齿2．Debur 去毛刺3．Decibel (CB) （噪音）分贝4．Decimal ratio 挂轮比值5．Dedendum 齿根高6．Dendendum angle 齿根角7．Dedendum surface 下齿面8．Deflection 挠曲9．Deflection test 挠曲试验10．Deflection testing machine 挠曲试验机11．Depthwise taper 齿高收缩12．Design data sheet 设计数据表13．Destructive pitting 破坏性点蚀14．Destructive wear 破坏性磨损15．Developed setting 试切调整16．Dial indicator 度盘式指示表17．Diametral pitch 径节18．Diamond 菱形接触19．Dinging ball check 钢球敲击检查20．Disc-mill cuter 盘铣刀21．Dish angle 凹角22．Displacement 位移23．Displacement error 位移误差24．Double index 双分度25．Double roll 双向滚动26．Down roll 向下滚动27．Drive side 工作齿侧28．Duplete 双刃刀29．Duplex 双重双面法30．Duplex helical 双重螺旋法（加工方法之一）31．Duplex spread blade 双重双面刀齿（加工／磨齿方法）32．Duplex taper 双重收缩齿33．Durability factor 耐久系数34．Dynamic factor 动载荷系数E。
齿轮参数-中英文对照_GearText_table_translation
fα fβ Hα Hβ i pt i p pk α β
说明 Description 齿廓形状偏差 螺旋线形状偏差 齿廓斜率偏差 螺旋线斜率偏差 一齿切向综合偏差 单个齿距偏差 切向综合总偏差 齿距累计总偏差 齿距累计偏差 齿廓总偏差 螺旋线总偏差 Profile form deviation Helix form deviation Profile slope deviation Helix slope deviation Tooth-to-tooth tangential composite deviation Single pitch deviation Total tangential composite deviation Total cumulative pitch deviation Cumulative pitch deviation Total profile deviation Total helix deviation
法向模数 纵向重合度 一齿径向综合偏差 径向综合总偏差 有效长度 精度等级 齿数 径向跳动
ε
f" F"
L
Q z
F
r
ISO 1328-2
符号 Symbol 12 13 14 15 16 17 18 19 20 说明 Description 分度圆直径
n β i i AE
d m
Reference diameter Normal module Overlap ratio Tooth-to-tooth radial composite deviation Total radial composite deviation Active length Accuracy grade number Number of teeth Run out
齿轮参数中英对照
齿轮参数术语中英文对照总结
齿轮参数术语中英文对照总结齿轮是机械传动中常用的元件，用于将动力传递给另一个轴。
在设计和制造齿轮时，需要了解一些齿轮参数术语。
以下是齿轮参数术语的中英文对照总结。
1. Pitch circle diameter（齿距圆直径）The diameter of the imaginary circle that passes through the centers of the gear teeth.（通过齿轮齿的中心点穿过的虚拟圆的直径）2. Module（模数）The ratio of the pitch circle diameter to the number of teeth.（齿距圆直径与齿数的比值）3. Pressure angle（压力角）4. Addendum（顶隙）The distance from the pitch circle to the top of the gear tooth.（从齿距圆到齿顶的距离）5. Dedendum（根隙）The distance from the pitch circle to the bottom of the gear tooth.（从齿距圆到齿底的距离）6. Circular pitch（齿距）The distance between corresponding points on adjacent teeth, measured along the pitch circle.（相邻齿上的对应点之间的距离，沿齿距圆测量）7. Diametral pitch（齿轮密度）The number of teeth per inch of pitch circle diameter.（每英寸齿距圆直径上的齿数）8. Working depth（工作深度）The distance between the addendum and dedendum.（顶隙和根隙之间的距离）9. Face width（齿宽）The width of the gear tooth measured parallel to the axis of rotation.（平行于旋转轴测量的齿宽）10. Helix angle（螺旋角）The angle formed between the helix of the gear tooth and a plane perpendicular to the gear axis.（齿轮齿的螺旋线与垂直于齿轮轴线的平面之间形成的角度）11. Backlash（背隙）The amount of clearance or play between meshing gear teeth.（啮合齿之间的间隙或游隙的量）12. Center distance（中心距）The distance between the centerlines of two meshing gears.（两个啮合齿轮中心线之间的距离）13. Pitch point（共轭点）The point of contact between the teeth of two meshing gears.（两个啮合齿轮的齿之间的接触点）14. Arc of action（干涉线）The path traced out by the contact points between meshing gears while they rotate.（啮合齿轮旋转时接触点之间构成的路径）15. Profile shifting（型位移）The modification of gear tooth profiles to achieve specific gear ratio adjustments.（根据所需的特定齿轮传动比进行齿形调整）。
齿轮参数 中英文对照
EXTERNAL SPUR GEAR DATA（外圆柱齿轮参数）manufacturing data（制造参数）part number（零件号）tooth form（齿面）gear type（齿轮类型）number of teeth（齿数）normal module（法向模数）normal pressure angle (at ref circle)法向压力角（在分度圆上）helix angle (at ref circle)螺旋角（在分度圆上）helical lead（螺旋导程）hand of helix（旋向）reference face width（参考齿宽）outside diameter（齿顶圆直径）chamfer diameter（倒圆直径）reference(pitch)circle diameter（分度圆直径）或节圆start of active profile diameter有效渐开线起始圆直径form diameter 展成直径root diameter齿根圆直径base circle diameter基圆直径whole depth全齿高normal circular tooth thickness (at reference circle)法向弧齿厚（在分度圆上）root type齿根形式root fillet radius 齿根圆角半径lead crown齿向鼓形HOB DATA滚刀参数pressure angle压力角tooth thickness at reference line分圆齿厚protuberance凸角tip radius齿顶圆半径reference part number 零件号INSPECTION DATA检验数据profile tolerance and modifications齿形公差和修形profile hollow齿形中凹refernce pitch circle runout节圆跳动pitch variation齿距偏差lead variation齿向偏差lead hollow齿向中凹profile surface finish渐开线齿面精加工ball diameter量球直径dimension over two balls in same plane跨棒距REFERENCE DATA-MATING GEAR对啮齿的参考参数normal center distance 中心距mating gear part number对啮齿轮零件号mumber of teeth on mating gear对啮轮齿数backlash (nominal CD ,ROOM TEMP)侧隙(法线方向，室温)general notes(通用技术要求)1.DO not scale drawing(不要在图上量取尺寸)2.all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX(所有面,角和边不能有毛刺,锐边倒钝不超过0.075mm)3.unless otherwise stated(除非特别注明,否则)A.all dimensions and tolerance are in millimeters perChinese standard(所有以毫米为单位的尺寸和公差均按中国标准)B.all surface finishes to be 3.2 micrometer or better(所有表面粗糙度不应低于3.2)C.all dimension are finished dimensions;no allowance has beenmade for any change in maximum or least material conditiondue to heat treatment(所有尺寸均为最终尺寸;热处理导致的最大或最小实体条件的变化不应超出允差)D linear dimensions to be +/- 0.25 MM(线性尺寸偏差为+/- 0.25 MM)E angular dimensions to be +/- 0.5º(角度尺寸偏差为+/- 0.5º)4.mark part number as shown(如图作零件号)5.mark serial number as shown(如图作系列号)6.heat treatment to be applied to all surfaces(整体热处理)gear notes(齿轮技术要求)1.do not grind roots and fillets after heat treatment(热处理后不得磨及齿根和圆角)2.no steps or grooves permissible in root and fillet region afterhoning or grinding(珩磨后,齿根和圆角区域不允许有台阶或凹痕)3.profile tolerance based upon floating band fit(齿形误差应以公差带为计)4.gear must be free from grind burns and tempering(齿面不得烧伤)5.pitch line runout and other tooth tolerances are with respect todatum A(节圆跳动和其它齿轮公差均以基准A为测量基准)6.profile tolerance to be measured between form and chamfer(齿形误差应由渐开线起始(或终止)圆测量至齿顶倒角)7.min hardness must be achieved in tooth root and fillet region(齿根和圆角处的硬度不得低于硬度下差)8.root radius tangent to profile not to extend above form diameter(齿根圆角要与齿面相切,而且不能超过渐开线起始(或终止)圆直径。
齿轮参数中英文对照表
A1 abrasive tooth wear 齿面研磨磨损2 absolute tangential velocity 绝对切向速度3 accelerometer 加速表4 addendum 齿顶高5 addendum angle 齿顶角6 addendum circle 齿顶圆7 addendum surface 上齿面8 adhesive wear 粘着磨损9 adjustability 可调性10 adjustability coefficients 可调系数11 adjusting wedge 圆盘端铣刀的可调型楔块12 allowable stress 允许应力13 alternate blade cutter 双面刀盘14 angular backlash 角侧隙15 angular bevel gears 斜交锥齿轮16 angular displacement 角移位17 angular pitch 齿端距18 angular testing machine 可调角度试验机19 approach action 啮入20 arbor 心轴21 arbor distance 心轴距22 arc of approach 啮入弧23 arc of recess 啮出弧24 attraction 收紧25 average cutter diameter 平均刀尖直径26 axial displacement 轴向位移27 axial factor 轴向系数28 axial locating surface 轴向定位面29 axial pitch 轴向齿距30 axial plane 轴向平面31 axial rakeangle 轴向前角32 axial thrust 轴向推力33 axle testing machine 传动桥试验机B1 back angle 背锥角2 Back angle distance 背角距（在背锥母线方向）3 Back cone 背锥4 Back cone distance 背锥距5 Back cone element 背锥母线6 Backlash 侧隙7 Backlash tolerance 侧隙公差8 Backlash variation 侧隙变量9 Backlash variation tolerance 侧隙变量公差10 Bandwidth 频带宽11 Base circle 基圆12 Base diameter 基圆直径13 Base pitch 基节14 Base radius 基圆半径15 Base spiral angle 基圆螺旋角16 Basic rack 基本齿条17 Bearing 轴承18 Bearing preload 轴承预负荷19 Bearing spacing／spread 轴承间距20 Bending fatigue 弯曲疲劳21 Bending stress 弯曲应力22 Bevel gears 锥齿轮23 Bias 对角接触24 Bias in 内对角接触25 Bias out 外对角接触26 Blade angle 刀齿齿廓角27 Blade edge radius 刀尖圆角半径28 Blade letter 刀尖凸角代号29 Blade life 刀尖寿命30 Blade point width 刀顶宽31 Blank offset 毛坯偏置距32 Bland position 毛坯位置33 Bottom land 齿槽底面34 Boundary lubrication 界面润滑35 Breakage 破裂36 Bridged contact pattern 桥型接触斑点37 Broach 拉刀38 Burnishing 挤齿C1 Case crushing 齿面塌陷2 CBN 立方氮化硼3 chamfer 倒角4 chordal addendum 弦齿高5 chordal thickness 弦齿厚6 chuck 卡盘7 circular broach 圆拉刀8 circular face-mill 圆盘端面铣刀9 circular peripheral-mill 圆盘铣刀10 circular pitch 周节11 circular thickness 弧齿厚12 circular thickness factor 弧齿厚系数13 clearance 顶隙14 clearance angle 后角15 coarse pitch 大节距16 coast side 不工作齿侧17 combination 组合18 combined preload 综合预负荷19 complementary crown gears 互补冠状齿轮20 completing cycle 全工序循环21 composite action 双面啮合综合检验误差22 compressive stress 压应力23 concave side 凹面24 concentricity 同心度25 concentricity tester 同心度检查仪26 cone distance 锥距27 cone element 锥面母线28 conformal surfaces 共型表面29 coniskoid 斜锥齿轮30 conjugate gears 共轭齿轮31 conjugate racks 共轭齿条32 contact fatigue 接触疲劳33 contact norma 接触点法线34 contact pattern (tooth contact pattern) 轮齿接触斑点35 contact ratio 重合度36 contact stress 接触应力37 continuous index 连续分度38 control gear 标准齿轮，检验用齿轮39 convex side 凸面40 coolant 冷却液41 corrosive wear 腐蚀性磨损42 corrugated tool 阶梯刨刀43 counter forma surfaces 反法向表面44 cradle 摇台45 cradle test roll 摇台角46 cross 大小端接触47 crossing point 交错点48 crown 齿冠49 crown circle 锥齿轮冠圆50 crowned teeth 鼓形齿51 crown gear 冠轮52 crown to back （轮冠距）轮冠至安装定位面距离53 crown to crossing point 轮冠至相错点距离54 cutter 刀盘55 cutter axial 刀盘的轴向位置56 cutter axial plane 刀盘轴向平面57 cutter axis 刀盘轴线58 cutter diameter 刀盘直径59 cutter edge radius 刀刃圆角半径60 cutter head 刀盘体61 cutter number 刀号62 cutter parallel 刀盘平垫片63 cutter point diameter 刀尖直径64 cutter point radius 刀尖半径65 cutter point width 刀顶距66 cutter spindle 刀盘主轴67 cutter spindle rotation angle 刀盘主轴转角68 cutting distance 切齿安装距69 CV testing mashing 常速试验机70 cyclex 格里森粗铣精拉法圆盘端铣刀71 cylindrical gears 圆柱齿轮D1 Datum tooth 基准齿2 Debur 去毛刺3 Decibel (CB) （噪音）分贝4 Decimal ratio 挂轮比值5 Dedendum 齿根高6 Dendendum angle 齿根角7 Dedendum surface 下齿面8 Deflection 挠曲9 Deflection test 挠曲试验10 Deflection testing machine 挠曲试验机11 Depthwise taper 齿高收缩12 Design data sheet 设计数据表13 Destructive pitting 破坏性点蚀14 Destructive wear 破坏性磨损15 Developed setting 试切调整16 Dial indicator 度盘式指示表17 Diametral pitch 径节18 Diamond 菱形接触19 Dinging ball check 钢球敲击检查20 Disc-mill cuter 盘铣刀21 Dish angle 凹角22 Displacement 位移23 Displacement error 位移误差24 Double index 双分度25 Double roll 双向滚动26 Down roll 向下滚动27 Drive side 工作齿侧28 Duplete 双刃刀29 Duplex 双重双面法30 Duplex helical 双重螺旋法（加工方法之一）31 Duplex spread blade 双重双面刀齿（加工／磨齿方法）32 Duplex taper 双重收缩齿33 Durability factor 耐久系数34 Dynamic factor 动载荷系数E1 Ease-off 修正、失配2 Eccentric 偏心3 Eccentric angle 偏心角4 Eccentricity 偏心度5 Edge radius 刀尖圆角半径6 Effective bearing spacing 轴承有效间距7 Effective face width 有效宽度（有效齿宽）8 Elastic coefficient 弹性系数9 Elastic deformation 弹性变形10 Elastic limit 弹性极限11 Elastohydrodynamic lubrication 弹性液压润滑12 Element 母线、要素13 End movement 轴向移动14 Endrem 修内端凸轮、导程凸轮15 Endurance life 耐久寿命16 Endurance limit 耐久极限17 Engine torque 发动机扭矩18 Enveloping 包络19 EP lubricant, EP 极压润滑剂20 EPG check, “EPG” 检查21 Equal addendum teeth 等齿顶高齿22 Equicurv 等高齿大轮成形法23 Equidep 等高齿24 Equiside 等边25 Equivalent fear ratio 当量传动比26 Equivalent number of teeth 当量齿数27 Equivalent pitch radius 当量节圆半径28 Equivalent rack 当量齿条29 Expander 涨胎30 Expanding arbor 可张心轴31 Extreme pressure lubricant 极压润滑剂F1 Face acvance 斜齿轮扭曲量2 Face angle 顶锥角（面锥角）3 Face angle distance 顶锥角距4 Face apex 顶锥顶5 Face apex beyond crossing point 顶锥顶至相错点距离6 Face cone 顶锥7 Face cone element 齿顶圆锥母线，面锥母线8 Face contact ratio 齿长重合度，轴向重合度（圆柱齿轮）9 Face line 齿面与轴面交线10 Face width 齿宽11 Factor of safety 安全系数12 Fatigue breakage 疲劳破裂13 Fatigue failure 疲劳失效14 Fatigue test 疲劳测试15 Feed cam 进给凸轮16 Feed gears 进给齿轮17 Fillet 齿根圆角18 Fillet curve 齿根过渡曲线19 Fillet radius 齿根圆角半径20 Film strength 液膜强度21 Filter (electronic) （电子的）滤波器22 Filter (mechanical) （机械的）滤波器23 Fine pitch （小模数）细径节24 Finisher 精切机床25 Fishtail 鱼尾形26 Fixed setting 固定安装法27 Flank 下齿面28 Flanking 下齿面加工29 Formarc 加工齿轮用的曲线齿廓刀具30 Formate 成形法31 Former 齿廓样板，靠模32 Forming 成型，在磨具内挤压成型33 Form tool 成形刀34 Fourier analysis 傅里叶分析35 Frequency 频率36 Friction load 摩擦负荷37 Front angle 前角38 Front cone 前锥39 Front crown 前锥齿冠40 Front crown to crossing point 前锥齿冠至交错点41 Full-depth teeth 全齿高齿42 Fundametal 基频G1 Gable 山形齿沟底面2 Gear 齿轮3 Gear axial displacement 齿轮轴向位移4 Gear axial plane 齿轮轴向平面5 Gear axis 齿轮轴线6 Gear center 齿轮中心7 Gear combination 齿轮组合8 Gear cone 大轮锥距9 Geared index 齿轮系分度10 Gear finisher 成形法齿轮精切机床11 Gear manufacturing summary 齿轮加工调整卡12 Gear marking compound 检查齿轮啮合涂色剂13 Gear member 大轮14 Gear planer 成型刨齿机15 Gear ratio 齿数比16 Gear rougher 齿轮粗切机床17 Gears 齿轮组18 Gear tipping 齿轮倾斜19 Generated gear 展成法齿轮20 Generating cam 展成凸轮21 Generating gear 展成齿轮22 Generating pressure angle 产形轮压力角23 Generating train 展成传动键24 Generation 展成25 Generator 展成齿轮加工机床26 Geneva index 星形轮分度，槽轮分度27 Geometry factor-durability 齿面接触强度几何系数28 Geometry factor0-strength 强度几何系数29 G-flow 格里森制金属件的商标，采用冷挤压成形法30 G-form 采用热锻成形法制造31 GLE-sine 砂轮内外压力角正弦波进行修整用机构32 G-plete 全工序法33 Gradeability 托曳力34 Grinding cracks 磨削裂纹35 G-spin 精密主轴的机床36 G-trac 圆柱齿轮的无端链式机床的商标H1 Hand of cutter 刀盘方向2 Hand of spiral 螺旋方向3 Hand-rolling tester 手动滚动试验机4 Hardac 镶篇淬硬刀体精切刀盘5 Hard finishing 硬齿面精加工6 Hardness ratio factor 硬度比系数7 Harmonic 谐振8 Harmonic search 谐振追踪9 Harmonic sweep 谐振扫描10 Heel 轮齿大端11 Heel pattern 大端接触12 Helical duplex 双重螺旋法13 Helical motion 螺旋运动14 Helixact 螺旋运动法15 Helixform 螺旋成形法16 Hertz (Hz) 赫兹17 Hook angle 断面前角18 Horizontal displacement 水平位移19 Horizontal offset 水平偏置20 HRH 高减速比准双曲面齿轮（大于10：1的减速比）21 Hunting tooth combination 大小齿轮齿数无公因数的齿轮副22 Hudrodynamic lubrication 液压润滑23 Hupermesh 超配合24 Hypoid gears 准双曲面齿轮25 Hypoid offset 准双曲面齿轮偏置距I1 Imaginary generating gear 假想成形法2 Incremental index 逐齿分度3 Index gears 分度齿轮4 Index interval 分度跳跃齿齿数5 Index plate 分度盘6 Index tolerance 分度公差7 Index variation 分度变化量8 Indicator anchorage 指示表支撑座9 Inertia factor 惯量系数10 Initial pitting 初期点蚀11 Inner addendum 小端齿顶高12 Inner cone distance 小端锥距13 Inner dedendum 小端齿根高14 Inner slot width 小端槽宽15 Inner spiral angle 小端螺旋角16 Inserted blade cutter 镶片刀盘17 Inside blade 内切刀齿18 Inside point diameter 内切刀尖直径19 Instantaneous contact pattern 瞬时接触斑点20 Interference 干涉21 Interference point 干涉点22 Interlocking disc-mill cutters 交错齿盘形铣刀23 Intermittent index 间断分度24 Internal bevel gear 内锥齿轮25 Inverse gear ratio 反齿数比26 Involute 渐开线27 Involute gear 渐开线齿轮28 Involute interference point 渐开线干涉点29 Involute spiral angle 渐开线螺旋角30 Involute teeth 渐开线齿J1 Jet lubrication 喷射润滑L1 Lame 顶根接触2 Lapping 研磨3 Lead cam 导程凸轮4 Length of action 啮合长度5 Lengthwise bridge 纵向桥型接触6 Lengthwise mismatch 纵向失配7 Lengthwise sliding velocity 纵向滑动速度8 Life factor 寿命系数9 Lift 垂直位移10 Limit point width 极限刀顶距11 Limit pressure angle 极限压力角12 Linear displacement transducer 线性位移传感器13 Line of action 啮合线14 Line of centers 中心线15 Line of contact 接触线16 Load sharing ratio 负荷分配比17 Localized tooth contact 齿局部接触18 Locating surface 定位表面19 Long-and-short-addendum teeth 高变位齿轮20 Long-toe-short-heel 小端长，大端短接触21 Lubricant 润滑剂22 Lubrication 润滑23 Lubricity 润滑性M1 Machine center 基床中心点2 Machine center to back 机床中心至工件安装基准面3 Machine plane 机床切削平面4 Machine root angle 毛坯安装角5 Marking compound 检查齿轮啮合型情况使用的涂色剂6 Master blade 标准刀齿7 Master gear 标准齿轮8 Mean addendum 中点齿顶高9 Mean cone distance 中点锥距10 Mean dedendum 中点齿根高11 Mean diametral pitch 中点径节12 Mean measuring addendum 中点测量齿顶高13 Mean measuring depth 中点测量齿高14 Mean measuring thickness 中点测量厚度15 Mean normal base pitch 中点法向基节16 Mean normal diameter pitch 中点法向径节17 Mean normal module 中点法向模数18 Mean point 中点，平均点19 Mean radius 中点半径20 Mean section 中点截面21 Mean slot width 中点齿槽宽22 Mean spiral angle 中点螺旋角23 Measuring addendum 测量齿顶高24 Measuring tooth thickness 测量齿厚25 Member 齿轮，元件26 Mesh point 啮合点27 Minimum slot width 最小槽宽28 Mismatch 失配29 Miter gears 等齿数整角锥齿轮副30 Mixed lubrication 混合润滑31 Modified contact ratio 修正总重合度32 Modified roll 滚修正比33 Module 模数34 Motion curves 运动曲线35 Motor torque 电机扭矩36 Mounting distance 安装距37 Mounting surface 安装面N1 Narrow-tow-wide-heel 小端窄大端宽接触2 No load 空载3 Nominal 名义4 Non-generated gear 非展成大轮5 Normal 法向，法线，法面6 Normal backlash 法向侧隙7 Normal backlash tolerance 法向侧隙公差8 Normal base pitch 法向基节9 Normal chordal addendum 法向弦齿高10 Normal chordal thickness 法向弦齿厚11 Normal circular pitch 法向周节12 Normal circular thickness 法向弧齿厚13 Normal contact ratio 法向重合度14 Normal diametral pitch 法向径节15 Normal direction 法线方向16 Normal (perpendicular) load 法向（垂直）负载17 Normal module 法向模数18 Normal plane 法向平面19 Normal pressure angle 法向压力角20 Normal section 法向截面21 Normal space-width taper 正常齿槽宽收缩22 Normal thickness taper 正常齿厚收缩23 Normal tilt 法向刀倾24 Normal wear 正常磨损25 No-roll roughing 无滚动粗切26 Number of teeth 齿数O1 Octoid teeth 锥齿轮的“8”字啮合2 Offset 偏置距3 Operating load 工作负荷4 Operating pressure angle 工作压力角5 Operating torque 工作扭矩6 Outer addendum 大端齿顶高7 Outer cone distance 外锥距8 Outer dedendum 大端齿根高9 Outer slot width 大端槽宽10 Outer spiral angle 大端螺旋角11 Outside blade 外切刃点12 Outside diameter 外径，大端直径13 Outside point diameter 外切刀尖直径14 Outside radius 齿顶圆半径15 Outside surface 外表面16 Overhung mounting 双支承安装17 Overload breakage 超负荷破裂18 Overload factor 超负荷系数P1 Path of action 啮合点轨迹2 Path of contact 接触迹3 Peak load 峰值负荷4 Peak torque 峰值扭矩5 Pedestal bearings 安装差速器壳的架座轴承6 Performance torque 性能扭矩7 Perim-mate 研磨锥齿轮和准双面齿轮用的全齿面研磨法8 Pinion 小轮9 Pinion axial displacement 小轮轴向位移10 Pinion cone 小轮锥距11 Pinion front bearing 小轮前端轴承12 Pinion head bearing 小轮后端前轴承13 Pinion rear bearing 小轮后端后轴承14 Pinion rougher 小轮粗切机15 Pinion offset 小轮偏置距16 Pitch 节距，齿距17 Pitch angle 节锥角18 Pitch apex 节锥顶19 Pitch apex beyond crossing point 节锥顶超出至相错点20 Pitch apex to back 节锥顶至安装端面21 Pitch apex to crown 节锥顶至轮冠22 Pitch circle 节圆23 Pitch cone 节锥24 Pitch curve 节面曲线25 Pitch diameter 节径26 Pitch element 节面母线27 Pitch line 节线28 Pitch-line chuck 节圆夹具29 Pitch-line runout 节线跳动30 Pitch plane 节面31 Pitch point 节点32 Pitch radius 节圆半径33 Pitch surfaces 节曲面34 Pitch tolerance 齿距公差35 Pitch trace 节线36 Pitch variation 齿距变化量37 Pitting 点蚀38 Plane of action 啮合平面39 Plane of rotation 旋转平面40 Planning generator 展成法刨齿机41 Plastic deformation 塑性变形42 Plastic flow 塑性流动43 Plate index 分度盘44 Point diameter 刀尖直径45 Point of contact 接触点46 Point radius 刀尖半径47 Point width 刀顶距48 Point width taper 刀顶距收缩49 Pressure lubrication 压力润滑50 Prime mover torque 原动机扭矩51 Profile angle 齿廓角52 Profile bridge 齿廓桥形接触53 Profile contact ratio 齿廓重合度54 Profile mismatch 齿廓啮合失配55 Profile radius of curvature 齿廓曲率半径56 Proof surface 检测基准面Q1 Quality measurement system 质量检测系统2 Quenching cracks 淬火裂纹3 Quenching die 淬火压模4 Quenching press 淬火压床R1 Rack 齿条2 Radial 径向刀位3 Radial load 径向负荷4 Radial locating surface 径向定位表面5 Radial rake angle 径向前角6 Ratio control roughing 变滚比粗切7 Ratio gears 滚比挂轮8 Ratio of roll 滚比9 Ratio of roll gears 滚比挂轮10 Recess action 啮出11 Relative displacement 相对位移12 Relative movement 相对运动13 Relative radius of curvature 相对曲率半径14 Residual stress 残余应力15 Revacycle 直齿锥齿轮圆拉法用机床及刀具16 Revex 直齿锥齿轮粗拉法17 Ridg-AC 镶片圆盘端面粗铣刀18 Ridging 沟条变形19 Ring gear 大轮，环形齿轮20 Rippling 振纹21 Roll centering 滚动定心22 Roll queching 滚动式淬火压床23 Roll gears 摆角挂轮24 Rolling 滚轧25 Rolling velocity 滚动速度26 Root angle 根锥角27 Root angle tilt 齿根角倾斜28 Root apex 根锥顶29 Root apex beyond crossing point 根锥顶至相错点的距离30 Root apex to back 根锥顶至安装基准面距离31 Root circle 齿根圆32 Root cone 根锥33 Root diameter 根圆直径34 Root line 齿根线35 Root radius 根圆半径36 Root surface 齿根曲面37 Roughac 弧齿锥齿轮粗切刀38 Rougher 粗切机39 RSR 弧齿锥齿轮条形刀齿铣刀盘40 Runout 径向跳动41 Runout tolerance 径向跳动公差S1 Scoring 胶合2 Scoring index 胶合指数3 Scuffing 胶合4 Sector 扇形齿／齿弧5 Segment 扇形齿／体6 Segmental-blade cutter 大轮精切刀7 Separation 分离间隙8 Separating factor 分离系数9 Separating force 分离力10 Set-in 补充切入，进刀11 Set-over 补充转角，调整转换12 Shaft angle 轴转角13 Shot peening 喷丸强化14 Sidebank 边频15 Side movement 侧向位移16 Side rake angle 侧前角17 Single cycle 单循环法18 Single roll 单滚动19 Single setting 单面调整法20 Single side 单面精切法21 Single-side taper 齿槽收缩22 Size factor 尺寸系数23 Skew bevel gears 斜直齿锥齿轮24 Skip index 跳齿分度25 Slide-roll ratio 单位滑滚比，比滑26 Sliding base 床鞍，滑座27 Sliding base setting 床鞍调整，滑座调整28 Sliding velocity 滑动速度29 Slip-chip 直齿锥齿轮一次成形刀30 Slip torque 滑移扭矩31 Slotting tool 切槽刀32 Slot width 槽宽33 Slot-width taper 槽宽收缩34 Small cutter development 小刀盘试切，能产生接近渐开线的刀具35 Solid cutter 整体刀盘36 Sound test 噪声试验37 Space-width taper 齿距收缩38 Spacing tolerance 齿距公差39 Spacing variation 齿距变动量40 Spalling 剥落41 Specific sliding 单位滑动比42 Speed gears 速度挂轮43 Spherical involute teeth 球面渐开线齿44 Spherica limacon teeth 球面钳线齿45 Spindle rotation angle 主轴旋转角46 Spiral angle 螺旋角47 Spiral bevel gears 弧齿锥齿轮48 Splash lubrication 飞溅润滑49 Split profile 齿型中断50 Spread blade 双面刀51 Spread blade 双面刀渐缩52 Standard depthwise taper 标准深锥度53 Standard taper 正常收缩54 Standard thickness 正常齿厚收缩55 Stock allowance 毛坯加工流量56 Straddle cutter 双列刀齿刀盘57 Straddle mounting 跨装58 Straight bevel gears 直齿锥齿轮59 Strength factor 强度系数60 Stress concentration factor 应力集中系数61 Stub teeth 短齿62 Subsurface initiated fatigue breakage 金属表面斜层初始疲劳破裂63 Summary of machine settings 机床调整卡64 Sump lubrication 油槽润滑65 Sum velocity 总速度66 Surface asperities 表面粗糙度67 Surface condition factor 表面条件系数68 Surface deformation 表面变形69 Surface durability 表面耐久度70 Surface fatigue 表面疲劳71 Surface initiated fatigue breakage 表面初始疲劳破裂72 Surface of action 啮合面73 Surface of revolution 回转面74 Surface treatment 表面处理75 Swinging base 回转底座76 Swing pinion cone 摆动小轮节锥法77 Swivel 刀转78 Swivel angle 刀转角79 Symmetrical rack 对称齿条80 Symmetrical rack proportions 对称齿条比例T1 Tangential load 切向负荷2 Tangent plane 切平面3 Tanline 小轮夹具4 Tanruf 双联粗切刀，85模数一下5 Tan-tru 用在加工1016－2540mm的锥齿刀具6 Taper roughing 具有刀顶距收缩的大小轮粗切过程7 Temperature factor 温度系数8 Testing machine 试验机9 Thickness taper 齿厚收缩10 Tilt 刀倾11 Tilt angle 刀倾角12 Tilted rootline taper 倾斜齿根收缩13 Tip radius 齿顶圆角半径14 Toe 轮齿小端15 Toe pattern 小端接触16 Tool 刀具17 Tool advance 刀具进刀18 Tool edge radius 刀刃圆角半径19 Tool point width 刀顶距20 Tooth angle 齿角21 Tooth bearing 齿支撑面，轮齿接触面22 Tooth contact analysis 轮齿接触分析23 Tooth contact pattern 轮齿接触斑点24 Tooth horizontal 齿水平面25 Tooth layout 轮齿剖面图26 Tooth-mesh frequency 齿啮合频率27 Tooth number 齿数28 Tooth profile 齿形，齿廓29 Tooth spacing testing 齿距检查仪30 Tooth spiral 齿螺旋线31 Tooth surface 轮齿表面32 Tooth taper 轮齿收缩33 Tooth-to-tooth composite tolerance 一齿度量中心距公差34 Tooth-to- Tooth composite variation 一齿度量中心距变量35 Tooth trace 齿线36 Tooth vertical 齿垂直面37 Top 齿顶38 Topland 齿顶面39 Topland width 齿顶面宽度40 Topping 修顶41 Top relief angle 顶刃后角42 Toprem 修根刀片43 Toprem angle 刀齿突角角度44 Top slope angle 刀齿顶刃倾角45 Total composite tolerance 总综合公差46 Total composite variation 总度量中心距变动量47 Total contact ratio 总重合度48 Total index tolerance 总分度公差49 Total index variation 总分度变动量50 Tractive effort torque 牵引力扭矩51 Transverse circular pitch 端面周节52 Transverse circular thickness 端面弧齿厚53 Transverse contact ratio 端面重合度54 Transverse diametral pitch 端面径节55 Transverse module 端面模数56 Transverse plane 端平面57 Transverse pressure angle 端面压力角58 Transverse space-width taper 端面槽宽收缩59 Transverse thickness taper 端面齿厚收缩60 Tredgold’s approximation 背锥近似法61 Tribology 润滑与磨损学62 Triplex 三面刃圆盘端铣刀63 Two-tool generator 双刀展成加工机床U1 Undercut 根切2 Undeveloped settings 试切前调整3 Uniform roll 匀速滚动4 Uniform velocity tester 匀速试验机5 Uni-spand 大轮心轴6 Unit load 单位负荷7 Unitool 曲面镶片刀8 Up-roll 向上滚动V1 V and H check 锥齿轮啮合的VH检查2 Variable roll 变滚动3 Velocity factor 速度系数4 Versacut 弧齿锥齿轮加工多用刀盘5 Vers-grip 卡紧小齿轮用的卡盘（商标名称）6 Vertical direction 垂直方向7 Vertical displacement 垂直位移8 Vertical factor 垂直系数9 Vertical force 垂直力10 Vertical offset 垂直偏置距11 Vertical plane 垂直面12 Virtual number of teeth 当量齿数13 Virtual pitch radius 当量节圆半径14 Viscosity 粘度15 V-tool V型刀具W1 Waveform 波形2 Wear 磨损3 Webless-type gear 无幅板式齿轮4 Web-type gear 幅板式齿轮5 Wheel slip torque 车轮打滑扭矩6 Whole depth 齿全高7 Workhead 工件头座8 Workhead offset 垂直轮位9 Workholding equipment 工件夹具10 Working depth 工作齿高11 Working stress 工作允许应力12 Work tests roll 检验工件主轴转角X1X-pandisk 大轮蝶形，涨胎心轴Z1 Zero depthwise taper 等齿高2 Zerol 零度锥齿轮。
齿轮参数中英文对照
EXTERNAL SPUR GEAR DAT外圆柱齿轮参数）manu facturi ng data （制造参数）part number （零件号）tooth form （齿面）gear type （齿轮类型）nu mber of teeth （齿数）normal module （法向模数）normal pressure angle （at ref circle）法向压力角（在分度圆上）helix angle （at ref circle）螺旋角（在分度圆上）helical lead （螺旋导程）hand of helix （旋向）referenee face width （参考齿宽）outside diameter （齿顶圆直径）chamfer diameter （倒圆直径）referen ce（pitch）circle diameter （分度圆直径）或节圆start of active profile diameter 有效渐开线起始圆直径form diameter 展成直径root diameter齿根圆直径base circle diameter 基圆直径whole depth 全齿高normal circular tooth thickness （at reference circle）法向弧齿厚（在分度圆上）root type齿根形式root fillet radius 齿根圆角半径lead crown齿向鼓形HOB DATA滚刀参数pressure angle 压力角tooth thickness at reference line 分圆齿厚protuberanee 凸角tip radius齿顶圆半径reference part number 零件号INSPECTION DAT检验数据profile tolerance and modifications 齿形公差和修形profile hollow 齿形中凹refernce pitch circle runout 节圆跳动pitch variation 齿距偏差lead variation 齿向偏差lead hollow 齿向中凹profile surface finish渐开线齿面精加工ball diameter量球直径dimension over two balls in same plane 跨棒距REFERENCE DATA-MATING GEAR齿齿的参考参数no rmal cen ter dista nce 中心距mating gear part number 对啮齿轮零件号mumber of teeth on mating gear 对啮轮齿数backlash （nominal CD ,ROOM TEMP侧隙（法线方向，室温） general notes （通用技术要求）1. DO not scale drawi ng（不要在图上量取尺寸）2. all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX（所有面，角和边不能有毛刺，锐边倒钝不超过0.075mm）3. unless otherwise stated（除非特别注明，否则）A. all dimensions and tolerance are in millimeters perCh in ese sta ndard（所有以毫米为单位的尺寸和公差均按中国标准）B. all surface finishes to be 3.2 micrometer or better（所有表面粗糙度不应低于 3.2）C. all dime nsion are fini shed dime nsions;no allowa nce has bee nmade for any change in maximum or least material conditiondue to heat treatment（所有尺寸均为最终尺寸；热处理导致的最大或最小实体条件的变化不应超出允差）D linear dimensions to be +/- 0.25 MM（线性尺寸偏差为+/- 0.25 MM）E angular dimensions to be +/- 0.5 o（角度尺寸偏差为+/- 0.5o）4. mark part number as shown（女口图作零件号）5. mark serial number as shown（如图作系列号）6. heat treatment to be applied to all surfaces（整体热处理） gear notes（齿轮技术要求）1. do n ot gri nd roots and fillets after heat treatme nt（热处理后不得磨及齿根和圆角）2. no steps or grooves permissible in root and fillet region afterho ning or grin di ng（珩磨后，齿根和圆角区域不允许有台阶或凹痕）3. profile tolerance based upon floating band fit（齿形误差应以公差带为计）4. gear must be free from grind burns and tempering（齿面不得烧伤）5. pitch line runout and other tooth tolera nces are with respect todatum A（节圆跳动和其它齿轮公差均以基准A为测量基准）6. profile tolerance to be measured between form and chamfer（齿形误差应由渐开线起始（或终止）圆测量至齿顶倒角）7. min hard ness must be achieved in tooth root and fillet regio n（齿根和圆角处的硬度不得低于硬度下差）8. root radius tan ge nt to profile not to exte nd above form diameter（齿根圆角要与齿面相切，而且不能超过渐开线起始（或终止）圆直径。
齿轮参数中英文对照表
A1 abrasive tooth wear 齿面研磨磨损2 absolute tangential velocity 绝对切向速度3 accelerometer 加速表4 addendum 齿顶高5 addendum angle 齿顶角6 addendum circle 齿顶圆7 addendum surface 上齿面8 adhesive wear 粘着磨损9 adjustability 可调性10 adjustability coefficients 可调系数11 adjusting wedge 圆盘端铣刀的可调型楔块12 allowable stress 允许应力13 alternate blade cutter 双面刀盘14 angular backlash 角侧隙15 angular bevel gears 斜交锥齿轮16 angular displacement 角移位17 angular pitch 齿端距18 angular testing machine 可调角度试验机19 approach action 啮入20 arbor 心轴21 arbor distance 心轴距22 arc of approach 啮入弧23 arc of recess 啮出弧24 attraction 收紧25 average cutter diameter 平均刀尖直径26 axial displacement 轴向位移27 axial factor 轴向系数28 axial locating surface 轴向定位面29 axial pitch 轴向齿距30 axial plane 轴向平面31 axial rakeangle 轴向前角32 axial thrust 轴向推力33 axle testing machine 传动桥试验机B1 back angle 背锥角2 Back angle distance 背角距（在背锥母线方向）3 Back cone 背锥4 Back cone distance 背锥距5 Back cone element 背锥母线6 Backlash 侧隙7 Backlash tolerance 侧隙公差8 Backlash variation 侧隙变量9 Backlash variation tolerance 侧隙变量公差10 Bandwidth 频带宽11 Base circle 基圆12 Base diameter 基圆直径13 Base pitch 基节14 Base radius 基圆半径15 Base spiral angle 基圆螺旋角16 Basic rack 基本齿条17 Bearing 轴承18 Bearing preload 轴承预负荷19 Bearing spacing／spread 轴承间距20 Bending fatigue 弯曲疲劳21 Bending stress 弯曲应力22 Bevel gears 锥齿轮23 Bias 对角接触24 Bias in 内对角接触25 Bias out 外对角接触26 Blade angle 刀齿齿廓角27 Blade edge radius 刀尖圆角半径28 Blade letter 刀尖凸角代号29 Blade life 刀尖寿命30 Blade point width 刀顶宽31 Blank offset 毛坯偏置距32 Bland position 毛坯位置33 Bottom land 齿槽底面34 Boundary lubrication 界面润滑35 Breakage 破裂36 Bridged contact pattern 桥型接触斑点37 Broach 拉刀38 Burnishing 挤齿C1 Case crushing 齿面塌陷2 CBN 立方氮化硼3 chamfer 倒角4 chordal addendum 弦齿高5 chordal thickness 弦齿厚6 chuck 卡盘7 circular broach 圆拉刀8 circular face-mill 圆盘端面铣刀9 circular peripheral-mill 圆盘铣刀10 circular pitch 周节11 circular thickness 弧齿厚12 circular thickness factor 弧齿厚系数13 clearance 顶隙14 clearance angle 后角15 coarse pitch 大节距16 coast side 不工作齿侧17 combination 组合18 combined preload 综合预负荷19 complementary crown gears 互补冠状齿轮20 completing cycle 全工序循环21 composite action 双面啮合综合检验误差22 compressive stress 压应力23 concave side 凹面24 concentricity 同心度25 concentricity tester 同心度检查仪26 cone distance 锥距27 cone element 锥面母线28 conformal surfaces 共型表面29 coniskoid 斜锥齿轮30 conjugate gears 共轭齿轮31 conjugate racks 共轭齿条32 contact fatigue 接触疲劳33 contact norma 接触点法线34 contact pattern (tooth contact pattern) 轮齿接触斑点35 contact ratio 重合度36 contact stress 接触应力37 continuous index 连续分度38 control gear 标准齿轮，检验用齿轮39 convex side 凸面40 coolant 冷却液41 corrosive wear 腐蚀性磨损42 corrugated tool 阶梯刨刀43 counter forma surfaces 反法向表面44 cradle 摇台45 cradle test roll 摇台角46 cross 大小端接触47 crossing point 交错点48 crown 齿冠49 crown circle 锥齿轮冠圆50 crowned teeth 鼓形齿51 crown gear 冠轮52 crown to back （轮冠距）轮冠至安装定位面距离53 crown to crossing point 轮冠至相错点距离54 cutter 刀盘55 cutter axial 刀盘的轴向位置56 cutter axial plane 刀盘轴向平面57 cutter axis 刀盘轴线58 cutter diameter 刀盘直径59 cutter edge radius 刀刃圆角半径60 cutter head 刀盘体61 cutter number 刀号62 cutter parallel 刀盘平垫片63 cutter point diameter 刀尖直径64 cutter point radius 刀尖半径65 cutter point width 刀顶距66 cutter spindle 刀盘主轴67 cutter spindle rotation angle 刀盘主轴转角68 cutting distance 切齿安装距69 CV testing mashing 常速试验机70 cyclex 格里森粗铣精拉法圆盘端铣刀71 cylindrical gears 圆柱齿轮D1 Datum tooth 基准齿2 Debur 去毛刺3 Decibel (CB) （噪音）分贝4 Decimal ratio 挂轮比值5 Dedendum 齿根高6 Dendendum angle 齿根角7 Dedendum surface 下齿面8 Deflection 挠曲9 Deflection test 挠曲试验10 Deflection testing machine 挠曲试验机11 Depthwise taper 齿高收缩12 Design data sheet 设计数据表13 Destructive pitting 破坏性点蚀14 Destructive wear 破坏性磨损15 Developed setting 试切调整16 Dial indicator 度盘式指示表17 Diametral pitch 径节18 Diamond 菱形接触19 Dinging ball check 钢球敲击检查20 Disc-mill cuter 盘铣刀21 Dish angle 凹角22 Displacement 位移23 Displacement error 位移误差24 Double index 双分度25 Double roll 双向滚动26 Down roll 向下滚动27 Drive side 工作齿侧28 Duplete 双刃刀29 Duplex 双重双面法30 Duplex helical 双重螺旋法（加工方法之一）31 Duplex spread blade 双重双面刀齿（加工／磨齿方法）32 Duplex taper 双重收缩齿33 Durability factor 耐久系数34 Dynamic factor 动载荷系数E1 Ease-off 修正、失配2 Eccentric 偏心3 Eccentric angle 偏心角4 Eccentricity 偏心度5 Edge radius 刀尖圆角半径6 Effective bearing spacing 轴承有效间距7 Effective face width 有效宽度（有效齿宽）8 Elastic coefficient 弹性系数9 Elastic deformation 弹性变形10 Elastic limit 弹性极限11 Elastohydrodynamic lubrication 弹性液压润滑12 Element 母线、要素13 End movement 轴向移动14 Endrem 修内端凸轮、导程凸轮15 Endurance life 耐久寿命16 Endurance limit 耐久极限17 Engine torque 发动机扭矩18 Enveloping 包络19 EP lubricant, EP 极压润滑剂20 EPG check, “EPG” 检查21 Equal addendum teeth 等齿顶高齿22 Equicurv 等高齿大轮成形法23 Equidep 等高齿24 Equiside 等边25 Equivalent fear ratio 当量传动比26 Equivalent number of teeth 当量齿数27 Equivalent pitch radius 当量节圆半径28 Equivalent rack 当量齿条29 Expander 涨胎30 Expanding arbor 可张心轴31 Extreme pressure lubricant 极压润滑剂F1 Face acvance 斜齿轮扭曲量2 Face angle 顶锥角（面锥角）3 Face angle distance 顶锥角距4 Face apex 顶锥顶5 Face apex beyond crossing point 顶锥顶至相错点距离6 Face cone 顶锥7 Face cone element 齿顶圆锥母线，面锥母线8 Face contact ratio 齿长重合度，轴向重合度（圆柱齿轮）9 Face line 齿面与轴面交线10 Face width 齿宽11 Factor of safety 安全系数12 Fatigue breakage 疲劳破裂13 Fatigue failure 疲劳失效14 Fatigue test 疲劳测试15 Feed cam 进给凸轮16 Feed gears 进给齿轮17 Fillet 齿根圆角18 Fillet curve 齿根过渡曲线19 Fillet radius 齿根圆角半径20 Film strength 液膜强度21 Filter (electronic) （电子的）滤波器22 Filter (mechanical) （机械的）滤波器23 Fine pitch （小模数）细径节24 Finisher 精切机床25 Fishtail 鱼尾形26 Fixed setting 固定安装法27 Flank 下齿面28 Flanking 下齿面加工29 Formarc 加工齿轮用的曲线齿廓刀具30 Formate 成形法31 Former 齿廓样板，靠模32 Forming 成型，在磨具内挤压成型33 Form tool 成形刀34 Fourier analysis 傅里叶分析35 Frequency 频率36 Friction load 摩擦负荷37 Front angle 前角38 Front cone 前锥39 Front crown 前锥齿冠40 Front crown to crossing point 前锥齿冠至交错点41 Full-depth teeth 全齿高齿42 Fundametal 基频G1 Gable 山形齿沟底面2 Gear 齿轮3 Gear axial displacement 齿轮轴向位移4 Gear axial plane 齿轮轴向平面5 Gear axis 齿轮轴线6 Gear center 齿轮中心7 Gear combination 齿轮组合8 Gear cone 大轮锥距9 Geared index 齿轮系分度10 Gear finisher 成形法齿轮精切机床11 Gear manufacturing summary 齿轮加工调整卡12 Gear marking compound 检查齿轮啮合涂色剂13 Gear member 大轮14 Gear planer 成型刨齿机15 Gear ratio 齿数比16 Gear rougher 齿轮粗切机床17 Gears 齿轮组18 Gear tipping 齿轮倾斜19 Generated gear 展成法齿轮20 Generating cam 展成凸轮21 Generating gear 展成齿轮22 Generating pressure angle 产形轮压力角23 Generating train 展成传动键24 Generation 展成25 Generator 展成齿轮加工机床26 Geneva index 星形轮分度，槽轮分度27 Geometry factor-durability 齿面接触强度几何系数28 Geometry factor0-strength 强度几何系数29 G-flow 格里森制金属件的商标，采用冷挤压成形法30 G-form 采用热锻成形法制造31 GLE-sine 砂轮内外压力角正弦波进行修整用机构32 G-plete 全工序法33 Gradeability 托曳力34 Grinding cracks 磨削裂纹35 G-spin 精密主轴的机床36 G-trac 圆柱齿轮的无端链式机床的商标H1 Hand of cutter 刀盘方向2 Hand of spiral 螺旋方向3 Hand-rolling tester 手动滚动试验机4 Hardac 镶篇淬硬刀体精切刀盘5 Hard finishing 硬齿面精加工6 Hardness ratio factor 硬度比系数7 Harmonic 谐振8 Harmonic search 谐振追踪9 Harmonic sweep 谐振扫描10 Heel 轮齿大端11 Heel pattern 大端接触12 Helical duplex 双重螺旋法13 Helical motion 螺旋运动14 Helixact 螺旋运动法15 Helixform 螺旋成形法16 Hertz (Hz) 赫兹17 Hook angle 断面前角18 Horizontal displacement 水平位移19 Horizontal offset 水平偏置20 HRH 高减速比准双曲面齿轮（大于10：1的减速比）21 Hunting tooth combination 大小齿轮齿数无公因数的齿轮副22 Hudrodynamic lubrication 液压润滑23 Hupermesh 超配合24 Hypoid gears 准双曲面齿轮25 Hypoid offset 准双曲面齿轮偏置距I1 Imaginary generating gear 假想成形法2 Incremental index 逐齿分度3 Index gears 分度齿轮4 Index interval 分度跳跃齿齿数5 Index plate 分度盘6 Index tolerance 分度公差7 Index variation 分度变化量8 Indicator anchorage 指示表支撑座9 Inertia factor 惯量系数10 Initial pitting 初期点蚀11 Inner addendum 小端齿顶高12 Inner cone distance 小端锥距13 Inner dedendum 小端齿根高14 Inner slot width 小端槽宽15 Inner spiral angle 小端螺旋角16 Inserted blade cutter 镶片刀盘17 Inside blade 内切刀齿18 Inside point diameter 内切刀尖直径19 Instantaneous contact pattern 瞬时接触斑点20 Interference 干涉21 Interference point 干涉点22 Interlocking disc-mill cutters 交错齿盘形铣刀23 Intermittent index 间断分度24 Internal bevel gear 内锥齿轮25 Inverse gear ratio 反齿数比26 Involute 渐开线27 Involute gear 渐开线齿轮28 Involute interference point 渐开线干涉点29 Involute spiral angle 渐开线螺旋角30 Involute teeth 渐开线齿J1 Jet lubrication 喷射润滑L1 Lame 顶根接触2 Lapping 研磨3 Lead cam 导程凸轮4 Length of action 啮合长度5 Lengthwise bridge 纵向桥型接触6 Lengthwise mismatch 纵向失配7 Lengthwise sliding velocity 纵向滑动速度8 Life factor 寿命系数9 Lift 垂直位移10 Limit point width 极限刀顶距11 Limit pressure angle 极限压力角12 Linear displacement transducer 线性位移传感器13 Line of action 啮合线14 Line of centers 中心线15 Line of contact 接触线16 Load sharing ratio 负荷分配比17 Localized tooth contact 齿局部接触18 Locating surface 定位表面19 Long-and-short-addendum teeth 高变位齿轮20 Long-toe-short-heel 小端长，大端短接触21 Lubricant 润滑剂22 Lubrication 润滑23 Lubricity 润滑性M1 Machine center 基床中心点2 Machine center to back 机床中心至工件安装基准面3 Machine plane 机床切削平面4 Machine root angle 毛坯安装角5 Marking compound 检查齿轮啮合型情况使用的涂色剂6 Master blade 标准刀齿7 Master gear 标准齿轮8 Mean addendum 中点齿顶高9 Mean cone distance 中点锥距10 Mean dedendum 中点齿根高11 Mean diametral pitch 中点径节12 Mean measuring addendum 中点测量齿顶高13 Mean measuring depth 中点测量齿高14 Mean measuring thickness 中点测量厚度15 Mean normal base pitch 中点法向基节16 Mean normal diameter pitch 中点法向径节17 Mean normal module 中点法向模数18 Mean point 中点，平均点19 Mean radius 中点半径20 Mean section 中点截面21 Mean slot width 中点齿槽宽22 Mean spiral angle 中点螺旋角23 Measuring addendum 测量齿顶高24 Measuring tooth thickness 测量齿厚25 Member 齿轮，元件26 Mesh point 啮合点27 Minimum slot width 最小槽宽28 Mismatch 失配29 Miter gears 等齿数整角锥齿轮副30 Mixed lubrication 混合润滑31 Modified contact ratio 修正总重合度32 Modified roll 滚修正比33 Module 模数34 Motion curves 运动曲线35 Motor torque 电机扭矩36 Mounting distance 安装距37 Mounting surface 安装面N1 Narrow-tow-wide-heel 小端窄大端宽接触2 No load 空载3 Nominal 名义4 Non-generated gear 非展成大轮5 Normal 法向，法线，法面6 Normal backlash 法向侧隙7 Normal backlash tolerance 法向侧隙公差8 Normal base pitch 法向基节9 Normal chordal addendum 法向弦齿高10 Normal chordal thickness 法向弦齿厚11 Normal circular pitch 法向周节12 Normal circular thickness 法向弧齿厚13 Normal contact ratio 法向重合度14 Normal diametral pitch 法向径节15 Normal direction 法线方向16 Normal (perpendicular) load 法向（垂直）负载17 Normal module 法向模数18 Normal plane 法向平面19 Normal pressure angle 法向压力角20 Normal section 法向截面21 Normal space-width taper 正常齿槽宽收缩22 Normal thickness taper 正常齿厚收缩23 Normal tilt 法向刀倾24 Normal wear 正常磨损25 No-roll roughing 无滚动粗切26 Number of teeth 齿数O1 Octoid teeth 锥齿轮的“8”字啮合2 Offset 偏置距3 Operating load 工作负荷4 Operating pressure angle 工作压力角5 Operating torque 工作扭矩6 Outer addendum 大端齿顶高7 Outer cone distance 外锥距8 Outer dedendum 大端齿根高9 Outer slot width 大端槽宽10 Outer spiral angle 大端螺旋角11 Outside blade 外切刃点12 Outside diameter 外径，大端直径13 Outside point diameter 外切刀尖直径14 Outside radius 齿顶圆半径15 Outside surface 外表面16 Overhung mounting 双支承安装17 Overload breakage 超负荷破裂18 Overload factor 超负荷系数P1 Path of action 啮合点轨迹2 Path of contact 接触迹3 Peak load 峰值负荷4 Peak torque 峰值扭矩5 Pedestal bearings 安装差速器壳的架座轴承6 Performance torque 性能扭矩7 Perim-mate 研磨锥齿轮和准双面齿轮用的全齿面研磨法8 Pinion 小轮9 Pinion axial displacement 小轮轴向位移10 Pinion cone 小轮锥距11 Pinion front bearing 小轮前端轴承12 Pinion head bearing 小轮后端前轴承13 Pinion rear bearing 小轮后端后轴承14 Pinion rougher 小轮粗切机15 Pinion offset 小轮偏置距16 Pitch 节距，齿距17 Pitch angle 节锥角18 Pitch apex 节锥顶19 Pitch apex beyond crossing point 节锥顶超出至相错点20 Pitch apex to back 节锥顶至安装端面21 Pitch apex to crown 节锥顶至轮冠22 Pitch circle 节圆23 Pitch cone 节锥24 Pitch curve 节面曲线25 Pitch diameter 节径26 Pitch element 节面母线27 Pitch line 节线28 Pitch-line chuck 节圆夹具29 Pitch-line runout 节线跳动30 Pitch plane 节面31 Pitch point 节点32 Pitch radius 节圆半径33 Pitch surfaces 节曲面34 Pitch tolerance 齿距公差35 Pitch trace 节线36 Pitch variation 齿距变化量37 Pitting 点蚀38 Plane of action 啮合平面39 Plane of rotation 旋转平面40 Planning generator 展成法刨齿机41 Plastic deformation 塑性变形42 Plastic flow 塑性流动43 Plate index 分度盘44 Point diameter 刀尖直径45 Point of contact 接触点46 Point radius 刀尖半径47 Point width 刀顶距48 Point width taper 刀顶距收缩49 Pressure lubrication 压力润滑50 Prime mover torque 原动机扭矩51 Profile angle 齿廓角52 Profile bridge 齿廓桥形接触53 Profile contact ratio 齿廓重合度54 Profile mismatch 齿廓啮合失配55 Profile radius of curvature 齿廓曲率半径56 Proof surface 检测基准面Q1 Quality measurement system 质量检测系统2 Quenching cracks 淬火裂纹3 Quenching die 淬火压模4 Quenching press 淬火压床R1 Rack 齿条2 Radial 径向刀位3 Radial load 径向负荷4 Radial locating surface 径向定位表面5 Radial rake angle 径向前角6 Ratio control roughing 变滚比粗切7 Ratio gears 滚比挂轮8 Ratio of roll 滚比9 Ratio of roll gears 滚比挂轮10 Recess action 啮出11 Relative displacement 相对位移12 Relative movement 相对运动13 Relative radius of curvature 相对曲率半径14 Residual stress 残余应力15 Revacycle 直齿锥齿轮圆拉法用机床及刀具16 Revex 直齿锥齿轮粗拉法17 Ridg-AC 镶片圆盘端面粗铣刀18 Ridging 沟条变形19 Ring gear 大轮，环形齿轮20 Rippling 振纹21 Roll centering 滚动定心22 Roll queching 滚动式淬火压床23 Roll gears 摆角挂轮24 Rolling 滚轧25 Rolling velocity 滚动速度26 Root angle 根锥角27 Root angle tilt 齿根角倾斜28 Root apex 根锥顶29 Root apex beyond crossing point 根锥顶至相错点的距离30 Root apex to back 根锥顶至安装基准面距离31 Root circle 齿根圆32 Root cone 根锥33 Root diameter 根圆直径34 Root line 齿根线35 Root radius 根圆半径36 Root surface 齿根曲面37 Roughac 弧齿锥齿轮粗切刀38 Rougher 粗切机39 RSR 弧齿锥齿轮条形刀齿铣刀盘40 Runout 径向跳动41 Runout tolerance 径向跳动公差S1 Scoring 胶合2 Scoring index 胶合指数3 Scuffing 胶合4 Sector 扇形齿／齿弧5 Segment 扇形齿／体6 Segmental-blade cutter 大轮精切刀7 Separation 分离间隙8 Separating factor 分离系数9 Separating force 分离力10 Set-in 补充切入，进刀11 Set-over 补充转角，调整转换12 Shaft angle 轴转角13 Shot peening 喷丸强化14 Sidebank 边频15 Side movement 侧向位移16 Side rake angle 侧前角17 Single cycle 单循环法18 Single roll 单滚动19 Single setting 单面调整法20 Single side 单面精切法21 Single-side taper 齿槽收缩22 Size factor 尺寸系数23 Skew bevel gears 斜直齿锥齿轮24 Skip index 跳齿分度25 Slide-roll ratio 单位滑滚比，比滑26 Sliding base 床鞍，滑座27 Sliding base setting 床鞍调整，滑座调整28 Sliding velocity 滑动速度29 Slip-chip 直齿锥齿轮一次成形刀30 Slip torque 滑移扭矩31 Slotting tool 切槽刀32 Slot width 槽宽33 Slot-width taper 槽宽收缩34 Small cutter development 小刀盘试切，能产生接近渐开线的刀具35 Solid cutter 整体刀盘36 Sound test 噪声试验37 Space-width taper 齿距收缩38 Spacing tolerance 齿距公差39 Spacing variation 齿距变动量40 Spalling 剥落41 Specific sliding 单位滑动比42 Speed gears 速度挂轮43 Spherical involute teeth 球面渐开线齿44 Spherica limacon teeth 球面钳线齿45 Spindle rotation angle 主轴旋转角46 Spiral angle 螺旋角47 Spiral bevel gears 弧齿锥齿轮48 Splash lubrication 飞溅润滑49 Split profile 齿型中断50 Spread blade 双面刀51 Spread blade 双面刀渐缩52 Standard depthwise taper 标准深锥度53 Standard taper 正常收缩54 Standard thickness 正常齿厚收缩55 Stock allowance 毛坯加工流量56 Straddle cutter 双列刀齿刀盘57 Straddle mounting 跨装58 Straight bevel gears 直齿锥齿轮59 Strength factor 强度系数60 Stress concentration factor 应力集中系数61 Stub teeth 短齿62 Subsurface initiated fatigue breakage 金属表面斜层初始疲劳破裂63 Summary of machine settings 机床调整卡64 Sump lubrication 油槽润滑65 Sum velocity 总速度66 Surface asperities 表面粗糙度67 Surface condition factor 表面条件系数68 Surface deformation 表面变形69 Surface durability 表面耐久度70 Surface fatigue 表面疲劳71 Surface initiated fatigue breakage 表面初始疲劳破裂72 Surface of action 啮合面73 Surface of revolution 回转面74 Surface treatment 表面处理75 Swinging base 回转底座76 Swing pinion cone 摆动小轮节锥法77 Swivel 刀转78 Swivel angle 刀转角79 Symmetrical rack 对称齿条80 Symmetrical rack proportions 对称齿条比例T1 Tangential load 切向负荷2 Tangent plane 切平面3 Tanline 小轮夹具4 Tanruf 双联粗切刀，85模数一下5 Tan-tru 用在加工1016－2540mm的锥齿刀具6 Taper roughing 具有刀顶距收缩的大小轮粗切过程7 Temperature factor 温度系数8 Testing machine 试验机9 Thickness taper 齿厚收缩10 Tilt 刀倾11 Tilt angle 刀倾角12 Tilted rootline taper 倾斜齿根收缩13 Tip radius 齿顶圆角半径14 Toe 轮齿小端15 Toe pattern 小端接触16 Tool 刀具17 Tool advance 刀具进刀18 Tool edge radius 刀刃圆角半径19 Tool point width 刀顶距20 Tooth angle 齿角21 Tooth bearing 齿支撑面，轮齿接触面22 Tooth contact analysis 轮齿接触分析23 Tooth contact pattern 轮齿接触斑点24 Tooth horizontal 齿水平面25 Tooth layout 轮齿剖面图26 Tooth-mesh frequency 齿啮合频率27 Tooth number 齿数28 Tooth profile 齿形，齿廓29 Tooth spacing testing 齿距检查仪30 Tooth spiral 齿螺旋线31 Tooth surface 轮齿表面32 Tooth taper 轮齿收缩33 Tooth-to-tooth composite tolerance 一齿度量中心距公差34 Tooth-to- Tooth composite variation 一齿度量中心距变量35 Tooth trace 齿线36 Tooth vertical 齿垂直面37 Top 齿顶38 Topland 齿顶面39 Topland width 齿顶面宽度40 Topping 修顶41 Top relief angle 顶刃后角42 Toprem 修根刀片43 Toprem angle 刀齿突角角度44 Top slope angle 刀齿顶刃倾角45 Total composite tolerance 总综合公差46 Total composite variation 总度量中心距变动量47 Total contact ratio 总重合度48 Total index tolerance 总分度公差49 Total index variation 总分度变动量50 Tractive effort torque 牵引力扭矩51 Transverse circular pitch 端面周节52 Transverse circular thickness 端面弧齿厚53 Transverse contact ratio 端面重合度54 Transverse diametral pitch 端面径节55 Transverse module 端面模数56 Transverse plane 端平面57 Transverse pressure angle 端面压力角58 Transverse space-width taper 端面槽宽收缩59 Transverse thickness taper 端面齿厚收缩60 Tredgold’s approximation 背锥近似法61 Tribology 润滑与磨损学62 Triplex 三面刃圆盘端铣刀63 Two-tool generator 双刀展成加工机床U1 Undercut 根切2 Undeveloped settings 试切前调整3 Uniform roll 匀速滚动4 Uniform velocity tester 匀速试验机5 Uni-spand 大轮心轴6 Unit load 单位负荷7 Unitool 曲面镶片刀8 Up-roll 向上滚动V1 V and H check 锥齿轮啮合的VH检查2 Variable roll 变滚动3 Velocity factor 速度系数4 Versacut 弧齿锥齿轮加工多用刀盘5 Vers-grip 卡紧小齿轮用的卡盘（商标名称）6 Vertical direction 垂直方向7 Vertical displacement 垂直位移8 Vertical factor 垂直系数9 Vertical force 垂直力10 Vertical offset 垂直偏置距11 Vertical plane 垂直面12 Virtual number of teeth 当量齿数13 Virtual pitch radius 当量节圆半径14 Viscosity 粘度15 V-tool V型刀具W1 Waveform 波形2 Wear 磨损3 Webless-type gear 无幅板式齿轮4 Web-type gear 幅板式齿轮5 Wheel slip torque 车轮打滑扭矩6 Whole depth 齿全高7 Workhead 工件头座8 Workhead offset 垂直轮位9 Workholding equipment 工件夹具10 Working depth 工作齿高11 Working stress 工作允许应力12 Work tests roll 检验工件主轴转角X1X-pandisk 大轮蝶形，涨胎心轴Z1 Zero depthwise taper 等齿高2 Zerol 零度锥齿轮。
齿轮参数中英对照
齿轮基本术语(中英文对照) 齿轮 Toothed gear；Gear齿轮副 Gear pair平行轴齿轮副 Gear pair with parallel axes相交轴齿轮副 Gear pair with intersecting axes 齿轮系 Train of gears行星齿轮系 Planetary gear train齿轮传动 Gear drive；Gear transmission配对齿轮 Mating gears小齿轮 Pinion大齿轮 Wheel；Gear主动齿轮 Driving gear从动齿轮 Driven gear行星齿轮 Planet gear行星架 Planet carrier太阳轮 Sun gear内齿圈 Ring gear；Annulus gear外齿轮 External gear内齿轮 Internal gear中心距 Centre distance轴交角 Shaft angle连心线 Line of centres减速齿轮副 Speed reducing gear pair增速齿轮副 Speed increasing gear pair齿数比 Gear ratio传动比 Transmission ratio轴平面 Axial plane基准平面 Datum plane节平面 Pitch plane端平面 Transverse plane法平面 Normal plane分度曲面 Reference surface节曲面 Pitch surface齿顶曲面 Tip surface齿根曲面 Root surface基本齿廓 Basic tooth profile基本齿条 Basic rack产形齿条 Counterpart rack产形齿轮 Generating gear of a gear产形齿面 Generating flank基准线 Datum line轮齿 Gear teeth；Tooth齿槽 Tooth space右旋齿 Right-hand teeth左旋齿 Left-hand teeth变位齿轮 Gears with addendum modification；X-gears高度变位圆柱齿轮副 X-gear pair with reference centre distance 角度变位圆柱齿轮副 X-gear pair with modified centre distance 高度变位锥齿轮副 X-gear pair without shaft angle modification 角度变位圆柱齿轮副 X-gear pair with shaft angle modification 变位系数 Modification coefficient变位量 Addendum modification径向变位系数 Addendum modification coefficient中心距变位系数 Centre distance modification coefficient圆柱齿轮 Cylindrical gear顶圆 Tip circle根圆 Root circle齿距 Pitch齿距角 Angular pitch公法线长度 Base tangent length分度圆直径 Reference diameter节圆直径 Pitch diameter基圆直径 Base diameter顶圆直径 Tip diameter根圆直径 Root diameter齿根圆角半径 Fillet radius齿高 Tooth depth工作高度 Working depth齿顶高 Addendum齿根高 Dedendum弦齿高 Chordal height固定弦齿高 Constant chord height齿宽 Facewidth有效齿宽 Effective facewidth端面齿厚 Transverse tooth thickness法向齿厚 Normal tooth thickness端面基圆齿厚 Transverse base thickness法向基圆齿厚 Normal base thickness端面弦齿厚 Transverse chordal tooth thickness固定弦齿厚 Constant chord端面齿顶厚 Crest width法向齿顶厚 Normal crest width端面齿槽宽 Transverse spacewidth法向齿槽宽 Normal spacewidth齿厚半角 Tooth thickness half angle槽宽半角 Spacewidth half angle压力角 Pressure angle齿形角 Nominal pressure angle圆弧圆柱蜗杆 Arc-contact worm；hollow flank worm；ZC-worm 直廓环面蜗杆 Enveloping worm with straight line grneratrix；TA worm平面蜗杆 Planar worm wheel；P-worm wheel平面包络环面蜗杆 Planar double enveloping worm；TP-worm平面二次包络蜗杆 Planar double-enveloping worm wheel；TP-worm wheel锥面包络环面蜗杆 Toroid enveloping worm wheel；TK-worm wheel 渐开线包络环面蜗杆 Toroid enveloping worm hich involute holicoid generatrix；TI-worm锥蜗杆 Spiroid锥蜗轮 Spiroid gear锥蜗杆副 Spiroid gear pair中平面 Mid-plane长幅内摆线 Prolate hypocycloid短幅内摆线 Curtate hypocycloid渐开线 Involute；Involute to a circle延伸渐开线 Prolate involute缩短渐开线 Curtate involute球面渐开线 Spherical involute渐开螺旋面 Involute helicoid阿基米德螺旋面 Screw helicoid球面渐开螺旋面 Spherical involute helicoid圆环面 Toroid圆环面的母圈 Generant of the toroit圆环面的中性圈 Middle circle of the toroid圆环面的中间平面 Middle-plane of the toroid圆环面的内圈 Inner circle of the toroid啮合干涉 Meshing interference切齿干涉 Cutter interference齿廓修型 Profile modification；Profile correction修缘 Tip relief修根 Root relief齿向修形 Axial modification；Longitudinal correction 齿端修薄 End relief鼓形修整 Crowning鼓形齿 Crowned teeth挖根 Undercut瞬时轴 Instantaneous axis瞬时接触点 Point of contact瞬时接触线 Line of contact端面啮合线 Transverse path of contact啮合曲面 Surface of action啮合平面 Plane of action啮合区域 Zone of action总作用弧 Total arc of transmission端面作用弧 Transverse arc of transmission纵向作用弧 Overlap arc总作用角 Total angle of transmission端面作用角 Transverse angle of transmission纵向作用角 Overlap angle总重合度 Total contact ratio端面重合度 Transverse ratio纵向重合度 Overlap ratio标准齿轮 Standard gears非变位齿轮 X-gero gear标准中心距 Referencr centre distance名义中心距 Nominal centre distance分度圆柱面 Reference cylinder节圆柱面 Pitch cylinder基圆柱面 Basic cylinder齿顶圆柱面 Tip cylinder齿根圆柱面 Root cylinder节点 Pitch point节线 Pitch line分度圆 Reference circle节圆 Pitch circle基圆 Basic circle定位面 Locating face外锥距 Outer cone distance内锥距 Inner cone distance中点锥距 Mean cone distance背锥距 Back cone distance安装距 Locating distance轮冠距 Tip distance；crown to back冠顶距 Apex to crown偏置距 Offset齿线偏移量 Offset of tooth trace分锥角 Reference cone angle节锥角 Pitch cone angle顶锥角 Tip angle根锥角 Root angle背锥角 Back cone angle齿顶角 Addendum angel齿根角 Dedendum angle任意点压力角 Pressure angle at a point任意点螺旋角 Spiral angle at a point中点螺旋角 Mean spiral angle大端螺旋角 Outer spiral angle小端螺旋角 Inner spiral angle蜗杆 Worm蜗轮 Worm wheel蜗杆副 Worm gear pair圆柱蜗杆 Cylindrical worm圆柱蜗杆副 Cylindrical worm pair环面蜗杆 Enveloping worm环面蜗杆副 Enveloping worm pair阿基米德蜗杆 Straight sided axial worm；ZA-worm 渐开线蜗杆 Involute helicoid worm；ZI-worm法向直廓蜗杆 Straight sided normal worm；ZN-worm 锥面包络圆柱蜗杆 Milled helicoid worm；ZK-worm 椭圆齿轮 Elliptical gear非圆齿轮副 Non-circular gear pair圆柱针轮副 Cylindsical lantern pinion and wheel 针轮 Cylindsical tan tein gear ；pin-wheel谐波齿轮副 Harmoric gear drive波发生器 Wave generator柔性齿轮 Flexspine刚性齿轮 Circular spline非圆齿轮 Non-circular gear分度圆环面 Reference tosoid。
齿轮参数中英文对照
EXTERNAL SPUR GEAR DAT外圆柱齿轮参数）manufacturing data （制造参数）part number （零件号）tooth form （齿面）gear type （齿轮类型）number of teeth （齿数）normal module （法向模数）normal pressure angle （at ref circle）法向压力角（在分度圆上）helix angle （at ref circle）螺旋角（在分度圆上）helical lead （螺旋导程）hand of helix （旋向）reference face width （参考齿宽）outside diameter （齿顶圆直径）chamfer diameter （倒圆直径）reference（pitch）circle diameter （分度圆直径）或节圆start of active profile diameter 有效渐开线起始圆直径form diameter 展成直径root diameter 齿根圆直径base circle diameter 基圆直径whole depth 全齿高normal circular tooth thickness （at reference circle）法向弧齿厚（在分度圆上）root type 齿根形式root fillet radius 齿根圆角半径lead crown 齿向鼓形HOB DATA滚刀参数pressure angle 压力角tooth thickness at reference line 分圆齿厚protuberance 凸角tip radius 齿顶圆半径reference part number 零件号INSPECTION DAT检验数据profile tolerance and modifications 齿形公差和修形profile hollow 齿形中凹refernce pitch circle runout 节圆跳动pitch variation 齿距偏差lead variation 齿向偏差lead hollow 齿向中凹profile surface finish 渐开线齿面精加工ball diameter 量球直径dimension over two balls in same plane 跨棒距REFERENCE DATA-MATING GEAR齿齿的参考参数normal center distance 中心距mating gear part number 对齿齿轮零件号mumber of teeth on mating gear 对齿轮齿数backlash （nominal CD ,ROOM TEMP侧隙（法线方向，室温） general notes（通用技术要求）1. DO not scale drawing（不要在图上量取尺寸）2. all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX（所有面,角和边不能有毛刺,锐边倒钝不超过0.075mm）3. unless otherwise stated（除非特别注明,否则）A. all dimensions and tolerance are in millimeters perChi nese sta ndard（所有以毫米为单位的尺寸和公差均按中国标准）B. all surface finishes to be 3.2 micrometer or better（所有表面粗糙度不应低于3.2）C. all dimension are finished dimensions;no allowance has beenmade for any change in maximum or least material condition due to heat treatment（所有尺寸均为最终尺寸;热处理导致的最大或最小实体条件的变化不应超出允差）D linear dimensions to be +/- 0.25 MM（线性尺寸偏差为+/- 0.25 MM）E angular dimensions to be +/- 0.5 o（角度尺寸偏差为+/- 0.5o）4. mark part number as shown（如图作零件号）5. mark serial number as shown（如图作系列号）6. heat treatment to be applied to all surfaces（整体热处理） gear notes（齿轮技术要求）1. do not grind roots and fillets after heat treatment（热处理后不得磨及齿根和圆角）2. no steps or grooves permissible in root and fillet region afterhoning or grinding（珩磨后,齿根和圆角区域不允许有台阶或凹痕）3. profile tolerance based upon floating band fit（齿形误差应以公差带为计）4. gear must be free from grind burns and tempering（齿面不得烧伤）5. pitch line runout and other tooth tolerances are with respect todatum A（节圆跳动和其它齿轮公差均以基准A为测量基准）6. profile tolerance to be measured between form and chamfer（齿形误差应由渐开线起始（或终止）圆测量至齿顶倒角）7. min hardness must be achieved in tooth root and fillet region（齿根和圆角处的硬度不得低于硬度下差）8. root radius tangent to profile not to extend above form diameter（齿根圆角要与齿面相切,而且不能超过渐开线起始（或终止）圆直径。
齿轮参数-中英文对照
EXTERNAL SPUR GEAR DATA（外圆柱齿轮参数）manufacturing data(制造参数)part number（零件号）tooth form（齿面)gear type（齿轮类型）number of teeth(齿数)normal module（法向模数）normal pressure angle （at ref circle）法向压力角（在分度圆上)helix angle （at ref circle）螺旋角(在分度圆上）helical lead（螺旋导程）hand of helix（旋向）reference face width（参考齿宽）outside diameter(齿顶圆直径）chamfer diameter（倒圆直径）reference(pitch)circle diameter(分度圆直径）或节圆start of active profile diameter有效渐开线起始圆直径form diameter 展成直径root diameter齿根圆直径base circle diameter基圆直径whole depth全齿高normal circular tooth thickness （at reference circle）法向弧齿厚（在分度圆上）root type齿根形式root fillet radius 齿根圆角半径lead crown齿向鼓形HOB DATA滚刀参数pressure angle压力角tooth thickness at reference line分圆齿厚protuberance凸角tip radius齿顶圆半径reference part number 零件号INSPECTION DATA检验数据profile tolerance and modifications齿形公差和修形profile hollow齿形中凹refernce pitch circle runout节圆跳动pitch variation齿距偏差lead variation齿向偏差lead hollow齿向中凹profile surface finish渐开线齿面精加工ball diameter量球直径dimension over two balls in same plane跨棒距REFERENCE DATA-MATING GEAR对啮齿的参考参数normal center distance 中心距mating gear part number对啮齿轮零件号mumber of teeth on mating gear对啮轮齿数backlash （nominal CD ，ROOM TEMP)侧隙(法线方向,室温）general notes（通用技术要求)1。
齿轮参数中英文对照
EXTERNAL SPUR GEAR DATA（外圆柱齿轮参数）manufacturing data（制造参数）part number（零件号）tooth form（齿面）gear type（齿轮类型）number of teeth（齿数）normal module（法向模数）normal pressure angle (at ref circle)法向压力角（在分度圆上）helix angle (at ref circle)螺旋角（在分度圆上）helical lead（螺旋导程）hand of helix（旋向）reference face width（参考齿宽）outside diameter（齿顶圆直径）chamfer diameter（倒圆直径）reference(pitch)circle diameter（分度圆直径）或节圆start of active profile diameter有效渐开线起始圆直径form diameter 展成直径root diameter齿根圆直径base circle diameter基圆直径whole depth全齿高normal circular tooth thickness (at reference circle)法向弧齿厚（在分度圆上）root type齿根形式root fillet radius 齿根圆角半径lead crown齿向鼓形HOB DATA滚刀参数pressure angle压力角tooth thickness at reference line分圆齿厚protuberance凸角tip radius齿顶圆半径reference part number 零件号INSPECTION DATA检验数据profile tolerance and modifications齿形公差和修形profile hollow齿形中凹refernce pitch circle runout节圆跳动pitch variation齿距偏差lead variation齿向偏差lead hollow齿向中凹profile surface finish渐开线齿面精加工ball diameter量球直径dimension over two balls in same plane跨棒距REFERENCE DATA-MATING GEAR对啮齿的参考参数normal center distance 中心距mating gear part number对啮齿轮零件号mumber of teeth on mating gear对啮轮齿数backlash (nominal CD ,ROOM TEMP)侧隙(法线方向，室温)general notes(通用技术要求)1.DO not scale drawing(不要在图上量取尺寸)2.all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX(所有面,角和边不能有毛刺,锐边倒钝不超过0.075mm)3.unless otherwise stated(除非特别注明,否则)A.all dimensions and tolerance are in millimeters perChinese standard(所有以毫米为单位的尺寸和公差均按中国标准)B.all surface finishes to be 3.2 micrometer or better(所有表面粗糙度不应低于3.2)C.all dimension are finished dimensions;no allowance has beenmade for any change in maximum or least material condition due to heat treatment(所有尺寸均为最终尺寸;热处理导致的最大或最小实体条件的变化不应超出允差)D linear dimensions to be +/- 0.25 MM(线性尺寸偏差为+/- 0.25 MM)E angular dimensions to be +/- 0.5o(角度尺寸偏差为+/- 0.5o)4.mark part number as shown(如图作零件号)5.mark serial number as shown(如图作系列号)6.heat treatment to be applied to all surfaces(整体热处理)gear notes(齿轮技术要求)1.do not grind roots and fillets after heat treatment(热处理后不得磨及齿根和圆角)2.no steps or grooves permissible in root and fillet region afterhoning or grinding(珩磨后,齿根和圆角区域不允许有台阶或凹痕)3.profile tolerance based upon floating band fit(齿形误差应以公差带为计)4.gear must be free from grind burns and tempering(齿面不得烧伤)5.pitch line runout and other tooth tolerances are with respect todatum A(节圆跳动和其它齿轮公差均以基准A为测量基准)6.profile tolerance to be measured between form and chamfer(齿形误差应由渐开线起始(或终止)圆测量至齿顶倒角)7.min hardness must be achieved in tooth root and fillet region(齿根和圆角处的硬度不得低于硬度下差)8.root radius tangent to profile not to extend above form diameter(齿根圆角要与齿面相切,而且不能超过渐开线起始(或终止)圆直径。
齿轮参数术语中英文对照总结
齿轮参数术语中英文对照总结-标准化文件发布号：（9556-EUATWK-MWUB-WUNN-INNUL-DDQTY-KII齿轮参数中英对照英文齿轮参数中文齿轮参数number of teeth 齿数normal module 法向模数transverse module 端面模数addendum modification factor 变位系数reference diameter 分度圆直径tip diameter 齿顶圆直径root diameter 齿根圆直径base diameter 基圆直径prefinishing diameter 剃前渐开线起始圆直径control form diameter 渐开线检查有效直径effective outside diameter 渐开线终止圆直径lead 导程normal pressure angle 法向压力角transverse pressure angle 端面压力角helix angle 分度圆螺旋角base helix angle 基圆螺旋角hand of helix 旋向circular thickness on Dp 分度圆上弧齿厚chordal addendum 弦齿高normal circular thickness on Dp after finishing and heat treatment 分度圆弦齿厚base tangent measurement after finishing and heat treatment 公法线长度dimension over f diameter balls or pin after finishing and heat treament 跨棒距backlash 总侧系center distance 中心距tool tip radius 刀具齿顶圆角半径tooth tip fillet angle refered to axis 齿顶倒角number of teeth of mating gear 配对齿轮齿数Toothed gear；Gear 齿轮Gear pair 齿轮副Gear pair with parallel axes 平行轴齿轮副Gear pair with intersecting axes 相交轴齿轮副Train of gears 齿轮系Planetary gear train 行星齿轮系Gear drive；Gear transmission 齿轮传动Mating gears 配对齿轮Pinion 小齿轮Wheel；Gear 大齿轮Driving gear 主动齿轮Driven gear 从动齿轮Planet gear 行星齿轮Planet carrier 行星架Sun gear 太阳轮Ring gear；Annulus gear 内齿圈External gear 外齿轮Internal gear 内齿轮Centre distance 中心距Shaft angle 轴交角Line of centres 连心线Speed reducing gear pair 减速齿轮副Speed increasing gear pair 增速齿轮副Gear ratio 齿数比Transmission ratio 传动比Axial plane 轴平面Datum plane 基准平面Pitch plane 节平面Transverse plane 端平面Normal plane 法平面Reference surface 分度曲面Pitch surface 节曲面Tip surface 齿顶曲面Root surface 齿根曲面Basic tooth profile 基本齿廓Basic rack 基本齿条Counterpart rack 产形齿条Generating gear of a gear 产形齿轮Generating flank 产形齿面Right-hand teeth 右旋齿Left-hand teeth 左旋齿Gears with addendum modification；变位齿轮Addendum modification factor 变位系数X-gearsX-gear pair with reference centre distance 高度变位圆柱齿轮副X-gear pair with modified centre distance 角度变位圆柱齿轮副X-gear pair without shaft angle modification 高度变位锥齿轮副X-gear pair with shaft angle modification 角度变位圆柱齿轮副Modification coefficient 变位系数Addendum modification 变位量Addendum modification coefficient 径向变位系数Centre distance modification coefficient 中心距变位系数Cylindrical gear 圆柱齿轮Tip circle 顶圆Root circle 根圆Pitch 齿距Angular pitch 齿距角Base tangent length 公法线长度Reference diameter 分度圆直径Pitch diameter 节圆直径Fillet radius 齿根圆角半径Working depth 工作高度Addendum 齿顶高Dedendum 齿根高Chordal height 弦齿高Constant chord height 固定弦齿高Facewidth 齿宽Effective facewidth 有效齿宽Transverse tooth thickness 端面齿厚Normal tooth thickness 法向齿厚Transverse base thickness 端面基圆齿厚Normal base thickness 法向基圆齿厚Transverse chordal tooth thickness 端面弦齿厚Constant chord 固定弦齿厚Crest width 端面齿顶厚Normal crest width 法向齿顶厚Transverse spacewidth 端面齿槽宽Normal spacewidth 法向齿槽宽Tooth thickness half angle 齿厚半角Spacewidth half angle 槽宽半角Nominal pressure angle 齿形角Arc-contact worm；hollow flank worm；ZC-worm 圆弧圆柱蜗杆Enveloping worm with straight line grneratrix；TA worm 直廓环面蜗杆Planar worm wheel；P-worm wheel 平面蜗杆Planar double enveloping worm；TP-worm 平面包络环面蜗杆Planar double-enveloping worm wheel；TP-worm wheel 平面二次包络蜗杆Toroid enveloping worm wheel；TK-worm wheel 锥面包络环面蜗杆Toroid enveloping worm hich involute holicoid generatrix；TI-worm 渐开线包络环面蜗杆Spiroid 锥蜗杆Spiroid gear 锥蜗轮Spiroid gear pair 锥蜗杆副Mid-plane 中平面Prolate hypocycloid 长幅内摆线Curtate hypocycloid 短幅内摆线Involute；渐开线Involute to a circleProlate involute 延伸渐开线Curtate involute 缩短渐开线Spherical involute 球面渐开线Involute helicoid 渐开螺旋面Screw helicoid 阿基米德螺旋面Spherical involute helicoid 球面渐开螺旋面Toroid 圆环面Generant of the toroit 圆环面的母圈Middle circle of the toroid 圆环面的中性圈Middle-plane of the toroid 圆环面的中间平面Inner circle of the toroid 圆环面的内圈Meshing interference 啮合干涉Cutter interference 切齿干涉Profile modification；齿廓修型Profile correctionTip relief 修缘Root relief 修根Axial modification；齿向修形Longitudinal correctionEnd relief 齿端修薄Crowning 鼓形修整Crowned teeth 鼓形齿Undercut 挖根Instantaneous axis 瞬时轴Point of contact 瞬时接触点Line of contact 瞬时接触线Transverse path of contact 端面啮合线Surface of action 啮合曲面Plane of action 啮合平面Zone of action 啮合区域Total arc of transmission 总作用弧Transverse arc of transmission 端面作用弧Overlap arc 纵向作用弧Total angle of transmission 总作用角Transverse angle of transmission 端面作用角Overlap angle 纵向作用角Total contact ratio 总重合度Transverse ratio 端面重合度Overlap ratio 纵向重合度Standard gears 标准齿轮X-gero gear 非变位齿轮Referencr centre distance 标准中心距Nominal centre distance 名义中心距Reference cylinder 分度圆柱面Pitch cylinder 节圆柱面Basic cylinder 基圆柱面Tip cylinder 齿顶圆柱面Root cylinder 齿根圆柱面Pitch point 节点Pitch line 节线Reference circle 分度圆Pitch circle 节圆Basic circle 基圆Locating face 定位面Outer cone distance 外锥距Inner cone distance 内锥距Mean cone distance 中点锥距Back cone distance 背锥距Locating distance 安装距Tip distance；crown to back 轮冠距Apex to crown 冠顶距Offset 偏置距Offset of tooth trace 齿线偏移量Reference cone angle 分锥角Pitch cone angle 节锥角Tip angle 顶锥角Root angle 根锥角Back cone angle 背锥角Addendum angel 齿顶角Dedendum angle 齿根角Pressure angle at a point 任意点压力角Spiral angle at a point 任意点螺旋角Mean spiral angle 中点螺旋角Outer spiral angle 大端螺旋角Inner spiral angle 小端螺旋角Worm 蜗杆Worm wheel 蜗轮Worm gear pair 蜗杆副Cylindrical worm 圆柱蜗杆Cylindrical worm pair 圆柱蜗杆副Enveloping worm 环面蜗杆Enveloping worm pair 环面蜗杆副Straight sided axial worm；ZA-worm 阿基米德蜗杆Involute helicoid worm；ZI-worm 渐开线蜗杆Straight sided normal worm；ZN-worm 法向直廓蜗杆Milled helicoid worm；ZK-worm 锥面包络圆柱蜗杆Elliptical gear 椭圆齿轮Non-circular gear pair 非圆齿轮副Cylindsical lantern pinion and wheel 圆柱针轮副Cylindsical tan tein gear ；pin-wheel 针轮Harmoric gear drive 谐波齿轮副Wave generator 波发生器Flexspine 柔性齿轮Circular spline 刚性齿轮Non-circular gear 非圆齿轮Reference tosoid 分度圆环面11。
齿轮基本参数中英对照及解释
一、齿轮的基本参数 P1二、齿轮参数英文 P4三、齿轮参数解释 P8一、齿轮的基本参数10.1.2直齿圆柱齿轮的基本参数、各部分的名称和尺寸关系当圆柱齿轮的轮齿方向与圆柱的素线方向一致时，称为直齿圆柱齿轮。
表10.1.2-1列出了直齿圆柱齿轮各部分的名称和基本参数。
表10.1.2-1 直齿圆柱齿轮各部分的名称和基本参数名称符号说明示意图齿数z模数m πd=zp, d=p/πz, 令m=p/π齿顶圆da 通过轮齿顶部的圆周直径齿df 通过轮齿根部的圆周直径模数m是设计和制造齿轮的重要参数。
不同模数的齿轮要用不同的刀具来加工制造。
为了便于设计和加工，模数数值已标准化，其数值如表10.1.2-2所示。
表10.1.2-2 齿轮模数标准系列（摘录GB/T1357-1987）注：选用模数时，应优先选用第一系列；其次选用第二系列；括号内的模数尽可能不用。
标准直齿圆柱齿轮各部分的尺寸与模数有一定的关系，计算公式如表10.1.2-3。
表10.1.2-3 标准直齿圆柱齿轮轮齿各部分的尺寸计算一对相互啮合的齿轮，模数、压力角必须相等。
标准齿轮的压力角（对单个齿轮而言即为齿形角）为20°二、齿轮参数英文EXTERNAL SPUR GEAR DATA（外圆柱齿轮参数）manufacturing data（制造参数）part number（零件号）tooth form（齿面）gear type（齿轮类型）number of teeth（齿数）normal module（法向模数）normal pressure angle (at ref circle)法向压力角（在分度圆上）helix angle (at ref circle)螺旋角（在分度圆上）helical lead（螺旋导程）hand of helix（旋向）reference face width（参考齿宽）outside diameter（齿顶圆直径）chamfer diameter（倒圆直径）reference(pitch)circle diameter（分度圆直径）或节圆start of active profile diameter有效渐开线起始圆直径form diameter 展成直径root diameter齿根圆直径base circle diameter基圆直径whole depth全齿高normal circular tooth thickness (at reference circle)法向弧齿厚（在分度圆上）root type齿根形式root fillet radius 齿根圆角半径lead crown齿向鼓形HOB DATA滚刀参数pressure angle压力角tooth thickness at reference line分圆齿厚protuberance凸角tip radius齿顶圆半径reference part number 零件号INSPECTION DATA检验数据profile tolerance and modifications齿形公差和修形profile hollow齿形中凹refernce pitch circle runout节圆跳动pitch variation齿距偏差lead variation齿向偏差lead hollow齿向中凹profile surface finish渐开线齿面精加工ball diameter量球直径dimension over two balls in same plane跨棒距REFERENCE DATA-MATING GEAR对啮齿的参考参数normal center distance 中心距mating gear part number对啮齿轮零件号mumber of teeth on mating gear对啮轮齿数backlash (nominal CD ,ROOM TEMP)侧隙(法线方向，室温)general notes(通用技术要求)1.DO not scale drawing(不要在图上量取尺寸)2.all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX(所有面,角和边不能有毛刺,锐边倒钝不超过0.075mm)3.unless otherwise stated(除非特别注明,否则)A.all dimensions and toleranceing are in millimeters perchinese standard(所有以毫米为单位的尺寸和公差均按中国标准)B.all surface finishes to be 3.2 micrometer or better(所有表面粗糙度不应低于3.2)C.all dimension are finished dimensions;no allowance has beenmade for any change in maximum or leastmaterial conditiondue to heat treatment(所有尺寸均为最终尺寸;热处理导致的最大或最小实体条件的变化不应超出允差)D linear dimensions to be +/- 0.25 MM(线性尺寸偏差为+/- 0.25 MM)E angular dimensions to be +/- 0.5º(角度尺寸偏差为+/- 0.5º)4.mark part number as shown(如图作零件号)5.mark serial number as shown(如图作系列号)6.heat treatment to be applied to all surfaces(整体热处理)gear notes(齿轮技术要求)1.do not grind roots and fillets after heat treatment(热后不得磨及齿根和圆角)2.no steps or grooves permissible in root and fillet region afterhoning or grinding(珩磨后,齿根和圆角区域不允许有台阶或凹痕)3.profile tolerance based upon floating band fit(齿形误差应以公差带为计)4.gear must be free from grind burns and tempering(齿面不得烧伤)5.pitch line runout and other tooth tolerances are with respect todatum A(节圆跳动和其它齿轮公差均以基准A为测量基准)6.profile tolerance to be measured between form and chamfer(齿形误差应由渐开线起始(或终止)圆测量至齿顶倒角)7.min hardness must be achieved in tooth root and fillet region(齿根和圆角处的硬度不得低于硬度下差)8.root radius tangent to profile not to extend above form diameter(齿根圆角要与齿面相切,而且不能超过渐开线起始(或终止)圆)9.do not thru harden tooth tips(齿尖不得淬透)三、齿轮参数解释1) 什么是「模数」？★模数表示轮齿的大小。
齿轮参数中英文对照
EXTERNAL SPUR GEAR DATA （外圆柱齿轮参数）manufacturing data （制造参数）part number （零件号）tooth form （齿面）gear type （齿轮类型）number of teeth （齿数）normal module （法向模数）no rmal pressure an gle （at ref circle法向压力角（在分度圆上）helix an gle （at ref circle）螺旋角（在分度圆上）helical lead （螺旋导程）hand of helix （旋向）referenee face width （参考齿宽）outside diameter （齿顶圆直径）chamfer diameter （倒圆直径）reference（pitch）circle diameter （分度圆直径）或节圆start of active profile diameter 有效渐开线起始圆直径form diameter 展成直径root diameter 齿根圆直径base circle diameter基圆直径whole depth 全齿高no rmal circular tooth thick ness （at reference circle）法向弧齿厚（在分度圆上）root type 齿根形式root fillet radius 齿根圆角半径lead crown 齿向鼓形HOB DATA 滚刀参数pressure an gle压力角tooth thick ness at reference line 分圆齿厚protubera nee 凸角tip radius 齿顶圆半径reference part number 零件号INSPECTION DATA 检验数据profile tolerance and modifications 齿形公差和修形profile hollow 齿形中凹refernce pitch circle runout 节圆跳动pitch variation 齿距偏差lead variation 齿向偏差lead hollow 齿向中凹profile surface finish 渐开线齿面精加工ball diameter 量球直径dime nsion over two balls in same pla ne 跨棒距REFERENCE DATA-MATING GEAR 对啮齿的参考参数normal center distance 中心距mat ing gear part nu mber对啮齿轮零件号mumber of teeth on mat ing gear 对啮轮齿数backlash （nominal CD ,ROOM TEMP）侧隙（法线方向，室温） general notes通用技术要求）1. DO not scale drawi ng（不要在图上量取尺寸）2. all surfaces corners and edges must be free from burrsand sharp edges-break 0.075 MM MAX所有面角和边不能有毛刺，锐边倒钝不超过0.075mm）3. unless otherwise stated除非特别注明，否则）A. all dimensions and tolerance are in millimeters perChi nese sta ndard所有以毫米为单位的尺寸和公差均按中国标准）B. all surface fini shes to be 3.2 micrometer or better 所有表面粗糙度不应低于3.2）C. all dimension are finished dimensions;no allowance has beenmade for any change in maximum or least material condition due to heat treatme nt所有尺寸均为最终尺寸；热处理导致的最大或最小实体条件的变化不应超出允差）D linear dimensions to be +/- 0.25 MM（线性尺寸偏差为+/- 0.25 MM）E angular dimensions to be +/- 0.5 o（角度尺寸偏差为+/- 0.5 c）4. mark part number as shown（如图作零件号）5. mark serial number as shown如图作系列号）6. heat treatment to be applied to all surfaces整体热处理） gear notes齿轮技术要求）1. do n ot gri nd roots and fillets after heat treatme nt（热处理后不得磨及齿根和圆角）2. no steps or grooves permissible in root and fillet region afterhoning or grinding（珩磨后，齿根和圆角区域不允许有台阶或凹痕）3. profile tolera nee based upon floati ng band fit（齿形误差应以公差带为计）4. gear must be free from grind burns and tempering齿面不得烧伤）5. pitch line runout and other tooth tolerances are with respect todatum A（节圆跳动和其它齿轮公差均以基准A为测量基准）6. profile toleranee to be measured between form and chamfer齿形误差应由渐开线起始（或终止）圆测量至齿顶倒角）7. min hard ness must be achieved in tooth root and fillet regio n（齿根和圆角处的硬度不得低于硬度下差）8. root radius tangent to profile not to extend above form diameter（齿根圆角要与齿面相切，而且不能超过渐开线起始（或终止）圆直径。
齿轮参数术语中英文对照总结
齿轮参数中英对照英文齿轮参数中文齿轮参数number of teeth 齿数normal module 法向模数transverse module 端面模数addendum modification factor 变位系数reference diameter 分度圆直径tip diameter 齿顶圆直径root diameter 齿根圆直径base diameter 基圆直径prefinishing diameter 剃前渐开线起始圆直径control form diameter 渐开线检查有效直径effective outside diameter 渐开线终止圆直径lead 导程normal pressure angle 法向压力角transverse pressure angle 端面压力角helix angle 分度圆螺旋角base helix angle 基圆螺旋角hand of helix 旋向circular thickness on Dp 分度圆上弧齿厚chordal addendum 弦齿高normal circular thickness on Dp after finishing and heat treatment 分度圆弦齿厚base tangent measurement after finishing and heat treatment 公法线长度dimension over f diameter balls or pin after finishing and heat treament 跨棒距backlash 总侧系center distance 中心距tool tip radius 刀具齿顶圆角半径tooth tip fillet angle refered to axis 齿顶倒角number of teeth of mating gear 配对齿轮齿数Toothed gear；Gear 齿轮Gear pair 齿轮副Gear pair with parallel axes 平行轴齿轮副Gear pair with intersecting axes 相交轴齿轮副Train of gears 齿轮系Planetary gear train 行星齿轮系Gear drive；Gear transmission 齿轮传动Mating gears 配对齿轮Pinion 小齿轮Wheel；Gear 大齿轮Driving gear 主动齿轮Driven gear 从动齿轮Planet gear 行星齿轮Planet carrier 行星架Sun gear 太阳轮Ring gear；Annulus gear 内齿圈External gear 外齿轮Internal gear 内齿轮Centre distance 中心距Shaft angle 轴交角Line of centres 连心线Speed reducing gear pair 减速齿轮副Speed increasing gear pair 增速齿轮副Gear ratio 齿数比Transmission ratio 传动比Axial plane 轴平面Datum plane 基准平面Pitch plane 节平面Transverse plane 端平面Normal plane 法平面Reference surface 分度曲面Pitch surface 节曲面Tip surface 齿顶曲面Root surface 齿根曲面Basic tooth profile 基本齿廓Basic rack 基本齿条Counterpart rack 产形齿条Generating gear of a gear 产形齿轮Generating flank 产形齿面Tooth space 齿槽Right-hand teeth 右旋齿Left-hand teeth 左旋齿Gears with addendum modification；变位齿轮Addendum modification factor 变位系数X-gearsX-gear pair with reference centre distance 高度变位圆柱齿轮副X-gear pair with modified centre distance 角度变位圆柱齿轮副X-gear pair without shaft angle modification 高度变位锥齿轮副X-gear pair with shaft angle modification 角度变位圆柱齿轮副Modification coefficient 变位系数Addendum modification 变位量Addendum modification coefficient 径向变位系数Centre distance modification coefficient 中心距变位系数Cylindrical gear 圆柱齿轮Tip circle 顶圆Root circle 根圆Pitch 齿距Angular pitch 齿距角Base tangent length 公法线长度Reference diameter 分度圆直径Pitch diameter 节圆直径Fillet radius 齿根圆角半径Tooth depth 齿高Working depth 工作高度Addendum 齿顶高Dedendum 齿根高Chordal height 弦齿高Constant chord height 固定弦齿高Facewidth 齿宽Effective facewidth 有效齿宽Transverse tooth thickness 端面齿厚Normal tooth thickness 法向齿厚Transverse base thickness 端面基圆齿厚Normal base thickness 法向基圆齿厚Transverse chordal tooth thickness 端面弦齿厚Constant chord 固定弦齿厚Crest width 端面齿顶厚Normal crest width 法向齿顶厚Transverse spacewidth 端面齿槽宽Normal spacewidth 法向齿槽宽Tooth thickness half angle 齿厚半角Spacewidth half angle 槽宽半角Nominal pressure angle 齿形角Arc-contact worm；hollow flank worm；ZC-worm 圆弧圆柱蜗杆Enveloping worm with straight line grneratrix；TA worm 直廓环面蜗杆Planar worm wheel；P-worm wheel 平面蜗杆Planar double enveloping worm；TP-worm 平面包络环面蜗杆Planar double-enveloping worm wheel；TP-worm wheel 平面二次包络蜗杆Toroid enveloping worm wheel；TK-worm wheel 锥面包络环面蜗杆Toroid enveloping worm hich involute holicoid generatrix；TI-worm 渐开线包络环面蜗杆Spiroid 锥蜗杆Spiroid gear 锥蜗轮Spiroid gear pair 锥蜗杆副Mid-plane 中平面Prolate hypocycloid 长幅内摆线Curtate hypocycloid 短幅内摆线Involute；渐开线Involute to a circleProlate involute 延伸渐开线Curtate involute 缩短渐开线Spherical involute 球面渐开线Involute helicoid 渐开螺旋面Screw helicoid 阿基米德螺旋面Spherical involute helicoid 球面渐开螺旋面Toroid 圆环面Generant of the toroit 圆环面的母圈Middle circle of the toroid 圆环面的中性圈Middle-plane of the toroid 圆环面的中间平面Inner circle of the toroid 圆环面的内圈Meshing interference 啮合干涉Cutter interference 切齿干涉Profile modification；齿廓修型Profile correctionTip relief 修缘Root relief 修根Axial modification；齿向修形Longitudinal correctionEnd relief 齿端修薄Crowning 鼓形修整Crowned teeth 鼓形齿Undercut 挖根Instantaneous axis 瞬时轴Point of contact 瞬时接触点Line of contact 瞬时接触线Transverse path of contact 端面啮合线Surface of action 啮合曲面Plane of action 啮合平面Zone of action 啮合区域Total arc of transmission 总作用弧Transverse arc of transmission 端面作用弧Overlap arc 纵向作用弧Total angle of transmission 总作用角Transverse angle of transmission 端面作用角Overlap angle 纵向作用角Total contact ratio 总重合度Transverse ratio 端面重合度Overlap ratio 纵向重合度Standard gears 标准齿轮X-gero gear 非变位齿轮Referencr centre distance 标准中心距Nominal centre distance 名义中心距Reference cylinder 分度圆柱面Pitch cylinder 节圆柱面Basic cylinder 基圆柱面Tip cylinder 齿顶圆柱面Root cylinder 齿根圆柱面Pitch point 节点Pitch line 节线Reference circle 分度圆Pitch circle 节圆Basic circle 基圆Locating face 定位面Outer cone distance 外锥距Inner cone distance 内锥距Mean cone distance 中点锥距Back cone distance 背锥距Locating distance 安装距Tip distance；crown to back 轮冠距Apex to crown 冠顶距Offset 偏置距Offset of tooth trace 齿线偏移量Reference cone angle 分锥角Pitch cone angle 节锥角Tip angle 顶锥角Root angle 根锥角Back cone angle 背锥角Addendum angel 齿顶角Dedendum angle 齿根角Pressure angle at a point 任意点压力角Spiral angle at a point 任意点螺旋角Mean spiral angle 中点螺旋角Outer spiral angle 大端螺旋角Inner spiral angle 小端螺旋角Worm 蜗杆Worm wheel 蜗轮Worm gear pair 蜗杆副Cylindrical worm 圆柱蜗杆Cylindrical worm pair 圆柱蜗杆副Enveloping worm 环面蜗杆Enveloping worm pair 环面蜗杆副Straight sided axial worm；ZA-worm 阿基米德蜗杆Involute helicoid worm；ZI-worm 渐开线蜗杆Straight sided normal worm；ZN-worm 法向直廓蜗杆Milled helicoid worm；ZK-worm 锥面包络圆柱蜗杆Elliptical gear 椭圆齿轮Non-circular gear pair 非圆齿轮副Cylindsical lantern pinion and wheel 圆柱针轮副Cylindsical tan tein gear ；pin-wheel 针轮Harmoric gear drive 谐波齿轮副Wave generator 波发生器Flexspine 柔性齿轮Circular spline 刚性齿轮Non-circular gear 非圆齿轮Reference tosoid 分度圆环面。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
A.1.abrasive tooth wear 齿面研磨磨损2.absolute tangential velocity 绝对切向速度3.accelerometer 力口速表4.addendum 齿顶高5.addendum angle 齿顶角6.addendum circle 齿顶圆7.addendum surface 上齿面8.adhesive wear 粘着磨损9.adjustability 可调性10.adjustability coefficients 可调系数11.adjusting wedge圆盘端铳刀的可调型楔块12.allowable stress 允许应力13.alternate blade cutter 双面刀盘14.angular backlash 角侧隙15.angular bevel gears 斜交锥齿轮16.angular displacement 角移位17.angular pitch 齿端距18.angular testing machine 可调角度试验机19.approach action 啮入20.arbor 心轴21.arbor distanee 心轴距22.arc of approach 啮入弧23.arc of recess 啮出弧24.attraction 收紧25.average cutter diameter 平均刀尖直径26.axial displacement 轴向位移27.axial factor 轴向系数28.axial locating surface 车由向定位面29.axial pitch 轴向齿距30.axial plane 轴向平面31.axial rakeangle 轴向前角32.axial thrust 轴向推力33.axle testing machine 传动桥试验机B.1.back angle 背锥角2.Back angle distanee 背角距（在背锥母线方向）3.Back cone 背锥4.Back cone distanee 背锥距5.Back cone element 背锥母线6.Backlash 侧隙7.Backlash tolera nee 侧隙公差8.Backlash variatio n 侧隙变量9.Backlash variati on tolera nee 侧隙变量公差10.Bandwidth 频带宽11 . Base circle 基圆12.Base diameter 基圆直径13.Base pitch 基节14.Base radius 基圆半径15.Base spiral angle 基圆螺旋角16. Basic rack基本齿条17. Beari ng 轴承18. Bearing preload 轴承预负荷19. Beari ng spaci ng / spread 车由承间距20. Bending fatigue 弯曲疲劳21. Bending stress 弯曲应力22. Bevel gears 锥齿轮23. Bias对角接触24. Bias in内对角接触25. Bias out外对角接触26. Blade angle刀齿齿廓角27. Blade edge radius 刀尖圆角半径28. Blade letter刀尖凸角代号29. Blade life刀尖寿命30. Blade point width 刀顶宽31. Blank offset毛坯偏置距32. Bland position 毛坯位置33. Bottom land 齿槽底面34. Bou ndary lubricatio n 界面润滑35. Breakage 破裂36. Bridged con tact pattern 桥型接触斑点37. Broach 拉刀38. Burnishi ng 挤齿C .1.Case crushing 齿面塌陷2.CBN立方氮化硼3.chamfer 倒角4.chordal addendum 弦齿高5.chordal thickness 弦齿厚6.chuck 卡盘7.circular broach 圆拉刀8.circular face-mill 圆盘端面铳刀9.circular peripheral-mill 圆盘铳刀10.circular pitch 周节11.circular thickness 弧齿厚12.circular thickness factor 弧齿厚系数clearance 顶隙clearance angle 后角 coarse pitch 大节距 coast side 不工作齿侧 combin ati on 组合 combined preload 综合预负荷 complementary crown gears 互补冠状齿轮 completing cycle 全工序循环 composite action 双面啮合综合检验误差 compressive stress 压应力 con cave side 凹面 concen tricity 同心度 concentricity tester 同心度检查仪 cone distanee 锥距 cone element 锥面母线 con formal surfaces 共型表面 con iskoid 斜锥齿轮 conjugate gears 共轭齿轮 conjugate racks 共轭齿条 con tact fatigue 接触疲劳 con tact norma 接触点法线 con tact pattern (tooth con tact pattern)轮齿接触斑点 con tact ratio 重合度 con tact stress 接触应力 continuous index 连续分度control gear 标准齿轮， 检验用齿轮convex side 凸面 coolant 冷却液 corrosive wear 腐蚀性磨损 corrugated tool 阶梯刨刀 counter forma surfaces 反法向表面 cradle 摇台 cradle test roll 摇台角cross 大小端接触crossing point 交错点crown 齿冠crown circle 锥齿轮冠圆 crowned teeth 鼓形齿 crown gear 冠轮 crown to back (轮冠距)轮冠至安装定位面距离 crown to crossing point 轮冠至相错点距离 cutter 刀盘 cutter axial 刀盘的轴向位置 cutter axial plane 刀盘轴向平面13. 14. 15.16.17.18.19.20.21.22.23. 24. 25. 26. 27. 28. 29. 30. 31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.52.53.54.55.56.57.cutter axis 刀盘轴线58.cutter diameter 刀盘直径59.cutter edge radius 刀刃圆角半径60.cutter head 刀盘体61.cutter number 刀号62.cutter parallel 刀盘平垫片63.cutter point diameter 刀尖直径64.cutter point radius 刀尖半径65.cutter point width 刀顶距66.cutter spindle 刀盘主轴67.cutter spin die rotati on an gle 刀盘主轴转角68.cutting distanee 切齿安装距69. C.V. testing mashing 常速试验机70.cyclex格里森粗铳精拉法圆盘端铳刀71.cylindrical gears 圆柱齿轮D.1. Datum tooth 基准齿2. Debur去毛刺3. Decibel (CB)(噪音)分贝4. Decimal ratio 挂轮比值5. Dede ndum 齿根高6. Dendendum angle 齿根角7. Dedendum surface 下齿面& Deflection 挠曲9. Deflection test 挠曲试验10. Deflection testing machine 挠曲试验机11. Depthwise taper 齿高收缩12. Design data sheet 设计数据表13. Destructive pitting 破坏性点蚀14. Destructive wear 破坏性磨损15. Developed setting 试切调整16. Dial indicator度盘式指示表17. Diametral pitch 径节18. Diamo nd 菱形接触19. Dinging ball check 钢球敲击检查20. Disc-mill cuter 盘铳刀21. D ish angle 凹角22. Displacement 位移23. D isplacement error 位移误差24. D ouble index 双分度25. D ouble roll 双向滚动26. D own roll向下滚动27. D rive side工作齿侧28. D uplete 双刃刀Duplex 双重双面法 Duplex helical 双重螺旋法（加工方法之一） Duplex spread blade 双重双面刀齿（加工/磨齿方法） Duplex taper 双重收缩齿 Durability factor 耐久系数 Dynamic factor 动载荷系数 Ease-off 修正、失配 Ecce ntric 偏心Eccentric angle 偏心角 Eccen tricity 偏心度 Edge radius 刀尖圆角半径 Effective beari ng spaci ng 车由承有效间距 Effective face width 有效宽度（有效齿宽） Elastic coefficient 弹性系数 Elastic deformation 弹性变形 Elastic limit 弹性极限 Elastohydrody namic lubricatio n 弹性液压润滑 Element 母线、要素 End movement 车由向移动 En drem 修内端凸轮、导程凸轮 En dura nee life 耐久寿命 En dura nee limit 耐久极限 Engine torque 发动机扭矩 En velop ing 包络 EP lubricant, EP 极压润滑剂 EPG check, “ EPG 检查 Equal addendum teeth 等齿顶高齿 Equicurv 等高齿大轮成形法 Equidep 等高齿 Equiside 等边 Equivale nt fear ratio 当量传动比 Equivale nt nu mber of teeth 当量齿数 Equivale nt pitch radius 当量节圆半径 Equivale nt rack 当量齿条 Expa nder 涨胎 Expanding arbor 可张心车由 Extreme pressure lubrica nt 极压润滑剂 293031323334 E 。