挡板式水流开关使用手册

合集下载

FS15挡板式流量开关开关说明书

FS15挡板式流量开关开关说明书

FS15挡板式流量开关使用说明详细介绍:一、概述FS15是一种挡板式流量开关,挡板由不锈钢制成,本体为H59黄铜(可选不锈钢)其性能优于普通的流量开关。

全部以插入式结构供货,连结螺纹为G1/2"或其它尺寸。

根据用户要求,可以用各种耐腐蚀性材料制作。

根据用户要求,可以配上三通,以流通式结构供货。

二、主要技术指标◆环境温度: -40-90℃◆安装位置: 外壳上箭头与流动方向一致◆介质温度: -40-150℃◆安装管道:DN15~DN50◆触点容量: AC250V 0.2A (阻性),0.1(感性),一对常开常闭结点 。

◆耐压: 10Mpa◆连接螺纹: G1/2"锥形管螺纹或其它尺寸◆防护标准: IP65三、安装1.连结螺纹为1/2”锥形管螺纹。

注意安装时在锥形螺纹上绕聚四氟乙烯生料带。

2.挡片和介质流动方向一致。

3.流量开关前后应有较长的直管段,大于5倍管径。

4.须现场切割挡片的,应注意三通的管经,确保大于2/3挡片插入管道。

四、开关点的设定如果用户要求精确设定开关点,请在购买时向厂方提出,由工厂标定。

当干簧管开关(黑色塑料部分)逆水流方向移动时,动作值提高(即需要更大的流量打开开关),反之,动作值减小。

调整完后将螺丝锁死。

用户取得流量开关后,可以先熟悉一下开关的动作过程,然后再设定。

当开关还没有安装在现场时,用手移动挡板,调整好后再重复一次以验证开关点设定是否准确。

为了监示开关是否动作,可以用万用表接在开关电路中来判断动作是否发生。

五:流量表 单位;升/分管道尺寸接通 切断 备注 DN153.3 3 挡片入水长度为管径的三分之二DN204.6 4.2 DN257,3 7 DN3215 14.2 DN4025.3 24 DN50 36 34.4六:尺寸图线100cmNPT。

挡板式水流开关使用手册

挡板式水流开关使用手册

水流开关流量保护值的调整
在通常情况下,流量保护值在工厂已经标定好丌需再做调整。 如果现场丌得丌调整,可以按图1将调节螺丝盖板用力向上移动,露出“+”字 螺丝帽; 然后按图2打开盖板,拧松接线盒上部的“+”字螺丝,然后用小号的“+”字螺 丝刀拧图1露出的螺丝帽即可调节流量设定值,顺时针调节减少流量设定值,逆 时针增加流量设定值; 观察图3接线盒内部,微动开关组件向右滑动减少流量设定值,向左滑动增加流 量设定值,但向左滑动过多将可能寻致流量开关断开而丌能闭合。 调整好后将接线盒内的“+”字螺丝锁紧,盖上前盖板和侧盖板即可
水流开关流量保护值的调整水流开关流量保护值的调整水流开关流量保护值的调整
水流开关应用中问题
1、调试时如果遇到流量开关丌闭合时在确认水流量正常时可以调整流量保护值。 判断调节位置正确不否,可以用手沿水流方向推动挡片,要使微动开关闭合位置 才合适。 2、使用时请丌要扳动塑料壳体,否则将可能寻致相对位置变动促使水流开关丌 动作。 3、对于应用中的其它问题请致电ACOL公司寺求支持。 参考资料 /proshow_Banner332302009.html
挡板式水流开关使用手册
--ACOL(安巢)WFS2系列
简介
ACOL水流开关是用于电热水器、太阳能热水器、空调器以及其他水系统的水循 环控制、进出水控制、水加热控制、水泵开关控制、电磁阀通断控制或出水断电、 出水通电控制等过程,当达到一定流量后将水流转换为开关式电信号的传感器件。
水流开关的尺寸
水流开关的安装位置
挡板式流量开关的安装位置一般安装在水泵出水口到设备出水口的这段管路中, 最好丌要安装在水泵的吸入口的管路上,这样容易使水泵无法正常吸水,水流开 关也无法打开,对于这点需要特别注意。挡板式水流开关允许水平(塑料部分在 上)和垂直安装。

电动操控标准挡流阀说明书

电动操控标准挡流阀说明书

Actuated Valves ProductPremium Actuated Standard Butterfly Valve - ElectricIndustrial grade valve with patented seat design uses no liner. Eliminates seat-creep and reduces operating torque. Full-featured actuator can be custom configured with add-on accessories.The following Features are Standard with Electric Actuated Standard Butterfly Valve.•Solid SS316L Stem •ANSI Class 150 Bolt Pattern•150 psi @ 73°F (23°C) (Thru 12")•14"-100 psi, 16"-85 psi •18"-70 psi, 20"-24"-50 psi•115 VAC standard, optional voltages available•2-Position Operation with 2-SPDT Limit Switches •Additional set dry contacts SPDT limitSwitches•NEMA 4 Enclosure, Powder Coated •Basic Manual Override 1-1/2 through 4" (Declutchable Available)•Declutchable Manual Override 6" through 12"•Illuminated Position Indicator •HeaterPage 15Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Spears ® Manufacturing CompanySee MSRP-1 Sheet or Check Spears ®****************************.comforPricingPremium Actuated Standard Butterfly Valve - Electric When ordering Butterfly Valves with additional Actuator Accessories add a "-A" to the end of the basic part number and see Electric Actuator Accessories for Butterfly Valves to order add-on Actuator Accessories separately. EX: 41101A112-015 add the -A to create 41101A112-015-A.NOTE:Due to variations in potential system operating conditions, 14" -24" Actuated Butterfly Valve packages are sized according to application parameters. Please contact Spears ® for additional information.。

水流开关安装位置

水流开关安装位置

水流开关安装位置
水流开关安装方法
1、垂直安装:当垂直安装时,应装在由下至上流动的管段上。

2、水平安装:当安装在水平管道的上端时,应保证介质是满管,以防探头只接触到空气而未接触到介质。

3、倒装:当安装在水平管道的下端时,应保证管道底部没有沉淀物,以免探头被沉淀物覆盖而无法与探头充分接触。

水流开关安装位置
1、允许水平(塑料部分在上)和垂直安装。

2、安装位置一般安装在水泵出水口到设备出水口的这段管路中,不能安装在水泵的吸入口的管路上,这样容易使水泵无法正常吸水,水流开关也无法打开。

挡板试流量开关

挡板试流量开关

安装示意图
当垂直安装时,应装在由下至上流动的管段上。
当水平安装时,探头应避开空气和沉淀物。
产品选型表
MH6170 电子式流量开关
代号
过程连接
G12
接口螺纹 G1/2
G14
接口螺纹 G1/4
代号
电气接口
N
内螺纹
W
外螺纹
代号
供电方式
A
24V±20%供电
D
230V±15%供电
代号
输出方式
I
4-20mA 电流输出
△耐压: 50bar(铝型),100bar(不锈钢)
特点
△平均压力损失: 0.3bar(在25L/min)
极小的压力损失,良好的重复性,抗污能力.机 △介质温度: 最大90℃
械部分与电子部分完全隔离,适用于大流量经济型。 △防护等级: IP65
3倍于原FE30的活塞行程使设定精度更加精确。带有 △ FE30…GA材质: 外壳: 阳极氧化铝
开关设定刻度,用户无须在现场设定。LED显示开关 活塞: POM塑料
状态,双开关量输出可供选择。
弹簧: 不锈钢
应用
密封: NBR
气液两用型,工业自动化/ 机械设备/ 空气压 △ FE30…GK材质: 外壳: 不锈钢
缩工业/ 制冷及空调。
活塞: POM塑料
弹簧: 不锈钢
密封: NBR
参数表
型号
压力 最大流量
代号 过程连接
G41 螺纹接口 G1/4
G83 螺纹接口 G3/8
G21 螺纹接口 G1/2
G43 螺纹接口 G3/4
G1
螺纹接口 G1
代号 供电方式
D
24V±20%DC

水流开关水流量开关安全操作及保养规程

水流开关水流量开关安全操作及保养规程

水流开关水流量开关安全操作及保养规程1. 前言水流开关水流量开关是用于监测水流状态并控制水流量的装置。

本文将介绍水流开关水流量开关的安全操作规程以及保养规程,帮助用户正确和有效地使用和维护该装置。

2. 安全操作规程2.1 安装前的准备在安装水流开关水流量开关之前,需要进行以下准备工作:•确保安装位置符合设备要求,并能够方便监测水流状态;•检查设备包装是否完好,确保设备没有损坏;•确保安装人员具备相关的安装经验和技能。

2.2 安装步骤按照以下步骤进行水流开关水流量开关的安装:1.关闭水源,确保工作环境安全;2.清洁安装位置,确保没有杂物和污垢;3.将水流开关水流量开关安装在合适的位置,使用螺丝固定;4.确保装置与水管连接紧密并且无泄漏;5.打开水源,检查设备是否正常工作。

2.3 操作注意事项•使用前请仔细阅读产品说明书,并按照操作步骤进行操作;•请勿在高压下操作该装置,以免发生危险;•请勿将棉布等可燃物放置在装置附近,以免发生火灾;•请勿使用尖锐物体损坏装置,以免影响正常使用。

3. 保养规程正确保养水流开关水流量开关可以延长其使用寿命,并确保其性能正常。

以下是一些常见的保养规程:1.定期清洁:定期清洁装置以去除污垢和杂物。

首先,关闭水源,将装置拆卸下来,用清水和中性清洁剂清洁各个部位,然后用干净的布擦干并重新安装。

2.注意防冻:在寒冷的冬季,如遇到结冰的情况,请关闭水源并将装置从水管中拆卸下来,放置在温暖干燥的地方,等待冰融化后再重新安装。

3.定期检查:定期检查装置的工作状态,确保其正常运行。

特别注意观察是否有泄漏现象,如有泄漏及时处理。

4. 总结水流开关水流量开关是一项重要的设备,用于监测水流状态并控制水流量。

正确的操作和保养可以确保该装置的正常性能和安全使用。

本文介绍了水流开关水流量开关的安全操作规程以及保养规程,希望能对您有所帮助。

注意:本文仅用于提供操作和保养的参考信息,具体操作和保养应根据设备使用说明书进行。

莱恩士传感器LES-442说明书

莱恩士传感器LES-442说明书

莱恩士传感器LES-442说明书莱恩士传感器LES-442型功能特性目前可以根据水流量的大小设计挡板,减少水流通过流量传感器产生的水阻力,减少水系统压头损失,但由于挡板式长期受水流的冲击仍然有疲劳的问题,即使在工厂标定好流量值的也会发生设定点飘移。

通常在保护流量值不要求的地方使用,即用于水管内的水流突然中断的断流保护。

在国内针对水源热泵机组设计的非常少。

挡板式是专门针对水环/地源热泵空调机组的水流量监控而开发的,它针对不同的管径配有不同的挡片,每种挡片的水阻不超过0.5米水柱,相比靶式水阻已大大降低。

每个挡板式流量传感器都配有与水环热泵机组水管相同的管件,现场只需连接上水管即可,不需对挡片做任何改变,另外挡板式水流开关的承压大于25bar,在对水流量要求不高的水环热泵机组是一个低成本的水流开关。

经过在水环/地源热泵机组上使用的反馈来看,压差开关能有效判断水环热泵机组现场安装的水管路的问题,能彻底避免水流量少造成换热器冻坏的情况,流量传感器也可以保护由于水过滤器堵塞造成的水流量下降时换热器冻坏的情况,另外水管路压差开关没有靶流开关疲劳破坏的风险。

尤其在水管路有少量空气时,流量传感器工作非常稳定,不会出现类似靶流开关的漂浮情况,经过多年使用的反馈未发现压差开关本身有故障的情况。

*1液体必须可让超声波脉冲穿过,不可含有大型气六或过多气泡。

某些非标准管线的监控可能会不稳定(即衬里管)*2如果管线温度超过85°C,请联系基恩士*3零切C]流速可从设置中变更。

使用低流速范围的设备时,如果在变更零切口流速后流体停止流动,请执行原始调整。

*4此规格适用于流速分配稳定时。

此数值未考虑因设备因素所造成的流速分配脉冲或波动。

根据额定流星范围,转换表格中的F。

S。

(原始尺寸)。

*5lO-Link:兼容于规格v1.1/COM2(384kbps)。

设置文件可从基恩士网站下载。

如果设备使用环境下不允许通过网络下载文件,请联系近的莱恩士事务所。

BL-FRW系列挡板式流量开关

BL-FRW系列挡板式流量开关
BL-FRW系列挡板式流量开关
应用领域:
主要适用于中小管道液体流量的控制。
产品特点
可靠性高,使用寿命长。
设定值范围可调。
温度范围宽,承压高。
一、适用场合
中央空调等制冷设备冷却水系统、热泵、工业自动化,润滑系统,液压系统过程生产线、化工、净水污水处理系统、激光设备、焊接设备、造纸、食品、药业等一切需要检测液体流量的领域。
连接方式
DN10
0.08—0.30
G3/8(螺纹)
DN15
0.19—0.68
G1/2(螺纹)
DN20
0.35—1.21
G3/4(螺纹)
DN25
0.55—1.89
G1(螺纹)
DN32
0.97--3.57
G1-1/4(螺纹)
DN40
1.40—4.84
G1-1/2(螺纹)
DN50
2.18—7.55
G2(螺纹)
B
管道型挡板式
C
插入式挡板式
公称通径
15
DN 15mm
20
DN 20mm
25
DN 25mm
32
DN 32mm
40
DN 40mm
50
DN 50mm
65
DN 65mm
80
DN 80mm
100
DN 100mm
125
DN 125mm
150
DN 150mm
连接方式
W
外螺纹G1″
N
内螺纹G3/4″
F
法兰连接
材质
DN65
3.20—11.2
DN65(法兰)
DN80
1.40--14.8
DN80(法兰)

FB11气液两用挡板式流量开关

FB11气液两用挡板式流量开关

1
43 7
61 127.5
103.5 100
76.5 51.5 25.5 20
流量
尺寸图
挡板式流量开关 FB11系列
≈68
32
20
80
74
15
SW36
R1"
选型表 FB11-
FB11-
025 H
025 H
订货提示
M 详述
FB11档板式流量开关 螺纹接口 G1 外螺纹 M 金属结构
1.订货时请注明介质流向,介质种类,管径及期望设定值。我们可在出厂 时帮您完成设定。 2.若是黏性介质,请注明黏度,温度及介质种类。 3.若是气体介质,请注明压力(表压/绝压),温度及介质种类。
5
16
0.26…0.86
0.04
0.55
50
4
16
0.57…1.68
0.08
50
5
16
0.33…1.08
0.05
注:以上参数是将开关垂直安装于水平管路,以20℃水为介质测试得出的.
安装
适用介质
适用
注: 安装位置会影响开关值



上海博韩电子科技有限公司 http://www.shbohan.com.cn
端子接线
机械开关 常开+常闭 (250VAC,3A)
16 bar
0.08bar(流量最大时)
-25…80℃
0…90℃
G1管螺纹
IP33
主体: 不锈钢
过程连接: 黄铜
连接杆: 黄铜
档板: 不锈钢
密封: 外壳:
NBR ABS
安装管径 DN 1"
1 1/4" 1 1/2"

防水挡板使用方法

防水挡板使用方法

防水挡板使用方法我折腾了好久防水挡板的使用方法,总算找到点门道。

咱先说这个防水挡板拿来的时候,可能是一片片的,得先把它们组装起来。

我一开始就很傻,以为随便插一插就行,结果根本不牢固。

后来我才发现,这有对应的卡槽和卡块,就像搭积木一样,你得把卡块慢慢对准卡槽,然后稳稳地插进去,听到那种轻微的“咔哒”一声,就表示卡上了。

搭好之后,就是放置的位置了。

我试过好几个地方,最初想当然地把它放在一个比较低的地方,觉得只要能挡住水就好。

可实际呢,水会从旁边或者下面渗过去。

后来我才明白,这得放在水容易流到的关键位置,比如说靠近水源发生泄漏可能性比较大的地方,像水龙头底下或者洗衣机排水管的周围,并且要尽量保证它周围都是平整的。

如果高低不平,水还是会溜过去。

防水挡板的固定也很重要。

我有次没固定好,水一来就把挡板给冲歪了。

有的挡板边上有那种螺丝孔或者粘贴的部分。

如果是有螺丝孔的,就需要找合适的螺丝拧进去,把它固定在地面或者墙壁上,就像在墙上挂画框一样,得紧紧地固定住。

要是那种带粘贴功能的,一定要把粘贴的地方清理得干干净净的,不能有灰尘或者水,不然就贴不牢,这就像你贴手机膜,如果屏幕不干净,膜就贴不好。

还有啊,要定期检查防水挡板呢。

我之前放那儿就不管了,有次突然发现,底下不知道什么时候被什么东西顶起来了一个小缝,差点就出问题了。

所以过段时间就得看看它有没有变形啊,有没有松动之类的。

再有吧,不同的防水挡板可能功能上有差异。

我曾经用过一种号称特别高级的挡板,说是能防火防水。

但我发现明火烤一下,虽然没着起来,可这挡板的防水性能好像就有点下降了。

所以要是你碰到那种多功能的,就得严格按照它说的使用环境和限制来用,不要想当然地光认为能防水就乱用一气。

这防水挡板使用起来看似简单,其实好多细节不注意就容易出问题。

多试试,多总结自己的失败教训,总能用好它的。

BL-FRW系列挡板式流量开关

BL-FRW系列挡板式流量开关

中央空调等制冷设备冷却水系统、热泵、工业自动化,润滑系统,液压系统过程生产线、
化工、净水污水处理系统、激光设备、焊接设备、造纸、食品、药业等一切需要检测液体流
量的领域。
四、技术参数
1、基本参数 类型 外壳防护等级 输出形式 触点寿命
使用介质温度范围 工作介质
微动开关参数 最大承压 材质


IP65 微动开关 SPDT 输出或 Din 插头输出 10 万次 -30~110℃ 空气、水和油
八、流量设定值调整
在通常情况下,流量保护值已在工厂进行标定 好,不需再做调整,如果现场不得不调整,可以按 图将调节螺丝盖板用力向上移动,露出“+”字螺丝, 然后按图打开盖板,拧送接线盒上部的“+”字螺丝, 然后用小号的“+”字改锥拧动露出的螺丝帽即可调 节流量设定值,顺时针调节为减少流量设定值,逆 时针调节为增加流量设定值,观察图接线盒内部, 微动开关组件向右滑动减少流量设定值,向左滑动 增加流量设定值,但向左滑动过多将可能导致流量开关断开而不能闭合。调整好后将接线盒 内的“+”字螺丝锁紧,盖上前盖板和侧盖板即可。
5A(max.)、250VAC/DC)
25bar 壳体为黄铜或不锈钢,挡板为不锈钢材质
2、流量参数
管径
DN10 DN15 DN20 DN25
流量保护值设定范围(m3/h)
0.08—0.30 0.19—0.68 0.35—1.21 0.55—1.89
连接方式
G3/8(螺纹)
G1/2(螺纹) G3/4(螺纹)
G1(螺纹)
销售地址:天津市西青区华苑产业区(环外)海泰发展五道16号B-6号楼-1-602 工厂地址:天津市中北工业园(北园)外环实业园区12号 邮编:300384 电 话:022-58883241 58883240 58883239 58883238 传真:022-27984101 网 址:http://www.tjbily.com E-mail:zx@tjbily.com sale@tjbily.com

防爆挡板式流量开关安全操作及保养规程

防爆挡板式流量开关安全操作及保养规程

防爆挡板式流量开关安全操作及保养规程随着现代工艺技术的不断发展和应用,防爆、防腐、防震等安全性能要求也越来越高,而防爆挡板式流量开关就是一种安全操作工具。

本文将为大家介绍防爆挡板式流量开关的安全操作及保养规程。

基本概念防爆挡板式流量开关是一种通过测量粘度和密度,在管道流体内的体积或重量流量小于预定值时,通过切断管道流体的传感器来控制流量的阀门。

它有防爆等多种优点,广泛应用于各种工业管道控制中。

安全操作1. 设备选型在使用防爆挡板式流量开关之前,需要根据管道的具体情况和介质的类型、流量、压力等参数选择合适的开关型号。

同时,也要注意开关的材质、结构和规格是否符合实际需求。

选型不当会导致开关工作不稳定,影响生产效果。

2. 安装位置防爆挡板式流量开关单元是一种敏感的流体流量检测器,应该选择安装在管道的合适位置。

一般来说,建议将其安装在水平管道的正中央或管道的下部。

同时,为了使其能够更好地反应管道的流量变化,应在安装前对管道进行充分地准确校对。

3. 适当管径防爆挡板式流量开关的适配管径范围是有限的,应在使用前正确选择适当的管径,安装时需要确保与管道连接部位密封性良好。

4. 电气连接在进行电气连接前要确保电源符合开关的要求规范,以避免过载和短路等危险。

同时电气接线要牢固可靠,插头要注意防水。

5. 小心操作在使用防爆挡板式流量开关时,需要严格遵守操作规程,正确启停,注意保护控制器的操作仪表免受撞击和污染。

在开关使用时,应该留意开关处的防护罩是否完好,并且在启动与停止时注意维护顺序。

保养规程防爆挡板式流量开关的长期保养与维护,可以确保其始终保持功能完好和良好的运行性能。

以下是一些建议的保养规程:1. 清洁工作防爆挡板式流量开关需要时常清洁,以保持其沿用高质量工作。

在清洁之前,要将开关从灰尘和废气源中远离清洁。

清洁时,使用中性溶剂和柔软毛刷。

不要使用储存在家用清洁剂中的手工磨料或强碱性液体。

在完成清洁后,要确保开关处的防护罩是否完好,并检查防护罩的密封性。

挡板式流量开关

挡板式流量开关

挡板式流量开关
水流开关的一种
原理、特点
挡板式流量开关的机械部分与电子部分安全隔离。

产品不含容易导致故障发生的波纹管,电器部件不直接与温差大的金属部件接触,不存在电器部件产生冷凝水导致锈蚀的问题,它具有多种类型可供客户选择以适应不同的应用场合。

使用进口磁敏开关作为电气动作部件,它具有较小的断开和复位流量,是中央空调和工业流体控制的首选流量保护产品。

应用
挡板式流量开关气液两用型,可广泛应用于工业自动化/机械设备/空气压缩工业/制冷及空调领域,工业场合具体应用在水冷焊机、激光设备冷却系统、真空镀膜机、电炉、多晶硅铸锭炉等。

水流开关磁体不在流动的水道里,可用于污水系统中且能正常工作。

技术参数
△电压:250V (max.)
△最大电流及容量:1A、50VA
△接线方式:直接附线
△输出:SPST磁敏开关(工厂设定常开)
△耐压:25bar,可选择定制50bar
△平均压力损失:0.01bar(流量最大时)
△工作温度:-20...90℃
△外壳防护等级:IP65
△材料:接液壳体:镀镍黄铜
挡板:不锈钢
密封:PTFE
适用介质
水、汽、油。

Concerto 洗浴挡板系统说明书

Concerto 洗浴挡板系统说明书

CONCERTOShOwER TROllEy… w ith people in mind| 3More and more care facilities are turning to showering for residents’personal hygiene routines. Concerto offers a safe, well-provensystem for showering dependent patients and residents in a rangeof care environments.Concerto can play an important role in supporting safe assistedshowering and other hygiene routines at facilities for elderly care, acutecare or special care.This shower trolley is specifically designed as a safe platform toprovide extra care for frail or disabled dependent patients or residentswith no ability to support themselves, namely Emma, Edward, Emil andElise in the Mobility Gallery.Concerto is a proven showering solution that offers a far morehygienic and dignified alternative to a bed bath. Our shower trolley hasbeen used successfully in care facilities worldwide for many years toimprove hygiene routines for dependent residents.Patients are showered in a supine position on the comfortable softmattress. The trolley is stable and safe. Its fold-down side supports havedouble safety latches to prevent accidental opening.The wide, height-adjustable shower trolley offers ideal ergonomicworking conditions, providing full body access for showering,hairwashing, pedicure and complete drying, as well as sufficient width toturn the resident easily.Concerto is part of the comprehensive ArjoHuntleigh showeringrange. With Concerto , Carendo and Carino , ArjoHuntleigh providescare facilities with optimum showering solutions for residents andpatients at all levels of mobility.Assisted showeringwith extrA cAreConcerto is an ideal platform forergonomic hygiene routines such ashairwashing.Concerto4 |elderly cAreEasy and safe transfer to theConcerto using a slingliftSmooth transport with a straightsteering device for corridors.Regular foot care routines can beperformed easily and efficiently. Concerto improves the quality of life of dependent elderly residents by making showering routines safe, comfortable and dignified. For many dependent residents in long-term care the only daily hygiene option is a bed bath, which is uncomfortable and undignified. A bed bath also puts a lot of strain on the carer’s back and neck, as the procedure involves leaning over the bed. Concerto provides an ergonomic solution for showering dependents residents. The height-adjustable function, operated via a handset on the battery-powered Concerto model, means carers can always use the shower trolley at the appropriate safe working height. For safe operating procedures, Concerto generally requires two carers.Patient transfer to the shower trolley from the bed can be performed with a ceiling lift, mobile passive lifter or a horizontal transfer using Maxi Slide sliding sheets. Using the mobile Concerto , the resident can be transported to and from the shower area without any manual lifting. The Concerto can be combined with flush sinks to allow easy, convenient splash-free showering by the carers. The stretcher slopes gently for good water run-off. Drain and run-off channels in the sealed mattress also speed water drainage. Used shower water is directed via a flexible drain hose to a floor drain or toilet enabling a wider choice of rooms to be used as the shower area. After showering, the removable mattress and tiltable stretcher make cleaning/disinfection routines quick and easy.Concerto is a proven solution for high-quality extra care in the assisted showering of dependent residents. Thousands of our shower trolleys are in daily use at elderly care facilities around the world.MaxiSlide sliding sheets enable asafe, ergonomic sideways transfer.In acute care, theConcerto can providea good platform forcleaning wounds.Concerto| 5 At acute care facilities, Concerto can support routines thatrequire stringent standards of hygiene.Prior to surgical procedures, Concerto can act as an optimumstation for the necessary pre-op washing and hygiene routines.A drip feed bottle holder is available as an accessory. In woundor burn care, hygiene is a vital concern and Concerto offers aplatform for good access when washing or treating affected partsof the patient’s body.A mobile solution can be of particular benefit in acute care.The Concerto can be rapidly moved to wherever it is needed inthe facility. Our shower trolley, which can also serve as a usefulnursing table, is available in three different lengths making itsuitable for adults or children in acute care.Acute cAreThe soft mattress makes patients as comfortable aspossible during pre-op hygiene procedures.Concerto6 |speciAl cAreFor dependent residents in special care facilities, Concerto can offer a safe environmentfor assisted showering and a range of hygiene routines.Special care facilities cover a wide range of care environments where residents may bedependent as a result of mental or physical disablement. With three different lengths available,Concerto enables assisted showering and hygiene routines for both children and adults.Secure showering is essential for residents who haveseizures. The extra-high side support option may beapplicable for residents who are at risk.Concerto allows staff to offer extra care by providinga safe platform for routines a resident cannot managehimself, such as shaving.Concerto| 7 A range of Concerto accessories isavailable to maximise comfort andallow optimum adaptation for use inelderly, acute or special care.The wedge pillow and adjustable backsupport both enhance patient comfortand give the carer better access forcertain hygiene routines.A resident or patient assessmentmay indicate that extra-high sidesupports will provide the right level ofsafety.The drip feed bottle holder is mostapplicable in acute care environments.Wedge pillow Adjustable back support, three positionsDrip-feed bottle holderConcertoExtra-high side supportsAccessoriesStraight steering deviceTiltable stretcherFlexible drain, drains to toilet or floor drainDrain hose holderFeAturesElectrical model, battery poweredHandset holder, electrical model onlyE E E PROduCT SPECifiCaTiONS Product informationMax total load (SWL) 175 kg (385 lb.)Max patient weight 150 kg (330 lb.)Weight 74 kg (163 lb.)Weight (electric) 80 kg (176 lb.)Width (stretcher) 650 mm (25 5/8”)Total width (incl. side supports) 760 mm (29 7/8”)Total length (different stretchers) 1600 mm (63”) 1900 mm (74 7/8”)*2250 mm (88 1/2”)Length of chassis (incl. wheel frame) 995 mm (39 1/8”)Max internal length of chassis 820 mm (32 1/4”)Max external width of chassis 700 mm (27 1/2”)Min external width of chassis 300 mm (11 7/8”)Height of chassis 150 mm (5 7/8”)Height, top position floor to stretcher 890 mm (35”)Height, top position floor to stretcher 870 mm (34 1/4”)(electric)Height, low position floor to stretcher 570 mm (22 1/2”)Stroke range 320 mm (12 5/8”)Stroke range (electric) 300 mm (11 3/4”)Colour Grey and blueEquipped with head pillow and foldable side supports with safety lockDrain hose holders includedAvailable as oil hydraulic (manual) version and battery powered (electrical) version.*Adjustable +/- 50 mmE , who is almost completely bedridden and totally dependant Please contact ArjoHuntleigh for further information on the Mobility Gallery™.EMMa EMMa Mobility GalleryElderly Special Acute 800 mm (31”)3050 m m (120”)2700m m(106”)1900 mm (74 3/4”)2250 mm (88 5/8”)2360 mm (93”)350 mm (14”)800 mm (31”)600m m(24”)shower hose (2500 mm/98”) Floor drainGETiNGE GROuP is a leading global provider of products and systems that contribute to quality enhancement and cost efficiency within healthcare and life sciences. We operate under the three brands of arjohuntleigh , GETiNGE and MaQuET . arjohuntleigh focuses on patient mobility and wound management solutions. GETiNGE provides solutions for infection control within healthcare and contamination prevention within life sciences. MaQuET specializes in solutions, therapies and products for surgical interventions and intensive care.P。

水流开关使用说明书 doc

水流开关使用说明书 doc

水流开关使用说明书概述:3S系列液体水流开关用于流经管道的液体流量变化,例如水、乙二醇或其它非危害性液体。

当液体流量超过或低于设定的流量值时,其单刀双掷开关触点(SPDT)可使一个回路导通,而同时切断另外一个回路。

该水流开关通常使用在需要连锁作用或“断流”保护场所。

典型的应用为当冷冻机系统中冷却水断流时,可有效的切断压缩机电流,以保护冷冻机及整个冷冻系统的损坏。

特点:液体压力可高达1MPa,使用范围广。

不锈钢叶片有四,用于直径25~150mm通径的管路。

可根据需要拆卸叶片的节数或修正叶片的长度。

设定点可调整,用户可根据需要进行修整其流量值。

外壳采用全封闭结构,对电器装置有效的防尘,防水汽(可能会有少量凝露)电器开关为整件,封闭式,对少量凝露不会产生漏电的危险。

接线空间大,方便用户接线。

技术参数:电器负载AC250V 15A AC380V 10A绝缘电阻Over 100MΩ,DC500VM耐压AC 1500V/1minute触点寿命1000K 次波纹管寿命5000K 次最大压力17.5kg f/cm2(1750KPa)工作压力10kgf/cm2(1000KPa)环境温度0~60℃流体温度Max 100℃(212°F),150℃防护标准IP53接口规格DN15(1/2") DN20(3/4") DN25(1") NPT重量0.7kKg3S流量开关可根据所安装总管线的管径,使用不同叶片。

水流开关的安装3S系列水流开关采用NPT 密封螺纹管路接头,有1英寸、4分、6分三种规格,用户订货时选择与管径配套的接头。

外壳的箭头方向应与管路内流向一致水流开关应安装在水平管路上。

如必须安装在垂直管道上,则液体流向应向下往上流。

绝不允许安装在自上往下流向的垂直管路上。

水流开关在使用中绝不允许流向倒流,以免造成叶片反向断裂。

附:叶片修整图:注意:带*的叶片为出厂时安装的带∆的为附加的叶片(未安装)其余尺寸为修正用休整后的叶片安装时,其顶端不得与管壁有任何摩擦,且与管壁底部有5~10mm间隙接线图:典型安装图:水流开关的调节1、打开水流开关外壳;2、开关出厂时已设定在约为最小流量值。

挡片式水流开关安全操作及保养规程

挡片式水流开关安全操作及保养规程

挡片式水流开关安全操作及保养规程挡片式水流开关是一种关键的防火设备,用于控制建筑物或设备中的水流,以便在火灾时防止火源传播。

为确保挡片式水流开关的有效性,必须定期进行维护和保养。

本文将介绍挡片式水流开关的安全操作和保养规程。

I. 安全操作规程1. 安装在安装挡片式水流开关时,请遵循以下指南:•安装过程应由专业人员进行;•确保水流开关安装与运行的完整性和准确性;•调整水流开关的设置以确保它在需要时能够有效地控制水流。

2. 检查和测试定期检查和测试挡片式水流开关以确保其在火灾情况下有效。

•每月一次对挡板水流开关进行手动测试,检查其是否可以控制水流,包括停止水流和开始水流;•每年至少进行一次自动测试以确保挡板水流开关在火灾情况下可靠。

3. 管理导向管理导向是确保水流开关能在需要时控制水流的关键。

•确保水流开关周围没有物品堆积或阻塞;•定期清洁水流开关及周围环境,以避免灰尘和污垢封堵水流开关。

4. 操作如需使用水流开关,请遵循以下操作指南:•在过度使用过渡水流开关时,应按规定操作手动水流开关,以避免过度使用;•避免使用损坏或报废的水流开关,以确保其有效性。

II. 保养规程挡片式水流开关定期保养可以确保其有效性,避免故障并延长使用寿命。

1. 清理和检查定期清洁和检查挡片式水流开关,以确保其在火灾情况下可靠。

•每月一次对水流开关及周围环境进行检查和清洁;•定期清洁水流开关周围的灰尘和污垢;•检查水流开关是否受损或过度磨损。

2. 更换部件如果需要更换部件,请参考以下指南:•使用原厂品牌的替代部件;•确保部件能与现有水流开关匹配;•更换部件时务必按照操作手册进行操作。

3. 标识使用标识以便于确定挡片式水流开关及相关设备的位置,促进有效管理和维护。

•每个水流开关周围应有明显的标识;•每个挡片式水流开关应有明显的标识。

标识应包括位置,类型和设备编号。

III. 结论挡片式水流开关是建筑物防火装置中的一个重要组成部分,定期检查和保养可以确保其有效性。

挡板式流量计工作原理

挡板式流量计工作原理

挡板式流量计工作原理嘿,朋友们!今天咱们来聊聊挡板式流量计这个有趣的东西。

你可以把挡板式流量计想象成一个小小的交通指挥员,它在管道这个“大马路”里指挥着流体的“交通”呢。

挡板式流量计的工作原理其实并不复杂。

在管道里,有一个挡板就像一道小墙一样立在那里。

当流体(就像是一群奔跑的小动物)在管道里流动的时候,就会撞到这个挡板上。

流体撞到挡板的力量是和它的流量有关系的哦。

就好比你在跑步的时候,跑得越快,撞到墙上的力量就越大。

流体流量大的时候,撞到挡板的冲击力就强;流量小的时候,冲击力就弱。

这个挡板会因为流体的冲击而产生位移,就像你轻轻推一下一扇门,门会动一点点,用力推它就会动得更多。

挡板的位移量就是一个关键的信号。

那怎么知道这个位移量呢?这里就有一些巧妙的装置啦。

一般会有一些传感器之类的东西,它们就像小侦探一样,精确地检测挡板移动了多少。

传感器会把这个位移的信息转化成我们能看懂的信号,比如电信号或者其他的信号。

然后,根据预先设置好的一些计算方法(这就像是小侦探的破案秘籍),就可以得出流体的流量啦。

举个生活中的例子吧。

你家里的水龙头开得小的时候,水慢悠悠地流,要是开到最大,水就像小瀑布一样冲出来。

如果在水龙头的水管里装一个挡板式流量计,水流量小的时候,挡板只是微微晃动,传感器检测到小幅度的位移,算出流量比较小;水流量大的时候,挡板晃动得厉害,传感器就能发现挡板的大位移,算出大流量。

挡板式流量计在很多地方都很有用呢。

比如说在一些工厂里,像石油化工厂,那里有各种各样的流体在管道里运输,就像一个超级复杂的物流网络。

挡板式流量计就像一个个小小的管理员,精确地监测着每种流体的流量,确保整个生产流程顺利进行。

总的来说,挡板式流量计就是利用流体对挡板的冲击力产生的位移,再通过传感器检测和计算,从而得出流量的这么一个聪明的小设备呢。

它就这么默默地在管道世界里做着流量监测的工作,是不是很有趣呀?。

J Flow Controls 9200 系列挡流阀说明书

J Flow Controls 9200 系列挡流阀说明书

APPLICA TIONS & INDUSTRIESFEATURES & BENEFITS•Graphite Packing•Carbide, 17-4 and Cermamic Discs Available•Angle Body Design for Longevity •End Connections: Socket Weld •Bolted Bonnet for E ase of Maintenance STANDARDS9200 SeriesASME Class 900 / 1500•Steam Injection applications •Water Injection •Gas Injection •Production Flow Back •Live Loaded Packing Design CO2 Injection ••Liquid Bypass •Quarter Turn •Gas Bypass•Easily AutomatedSPECIFICATIONS - CLASS 1500 STEEL0.870.386.674.23234242319111227252228952667202118171410131581Part Number1. BodyA1052. Belleville Spring 17-4 PH H1150 + 11503. Stem17-4 PH H1150 + 11504. Stem Bushing 410 SS – QPQ 5. Guide Bearing Brass6. Packing Follower 410 SS – QPQ7. Gland Flange 17-4 PH8. Bonnet A1059.Wear Sleeve17-4 PH H1150 + 115010. Body Gasket 304 SS – Grafoil Filled 11. Outer Cage 17-4 PH H1150 + 115012. Drive Cage 17-4 PH H1150 + 115013. Packing Bushing 410 SS – QPQ 14. Nut-Packing GlandA194 Gr. 8M15. Stud-Packing Gland A193 B8M CL.117. Ferry Cap Screw A193 B718. Belleville Spring -17-7 PH Live Loaded 19. Washer 304 SS 20. Packing Ring Grafoil21. Anti-Extrusion Ring Inconel 718 / Grafoil 22. Seal Ring Grafoil 23. Spring A-28624. Retaining Ring 302 SS 25. Choke Disk WC26. Bracket Stainless Steel 27. Dowel Pin Alloy Steel 28. Dowel PinAlloy SteelDescriptionPart NumberDescriptionHOW TO ORDERSeries Orifice Size 92Body Material 2WCB/A015A 3/16"3316 B 1/4"*SW -Standard Ends- P lease see the J Flow Controls Configurator for a full list of body and trim materialsPacking G GraphiteDisc Material 3101117-4 SSTungstenCarbide CeramicC 3/8"D 1/2"E 5/8"F 3/4"End Connection SWSocket Weld *F300 ANSI 300F600 ANSI 600F900 ANSI 900F1500 ANSI 1500Orifice Sizes Available S izes Rated Cv 3/16" 1.61/4" 2.93/8" 6.61/2"11.75/8"18.43/4"26.44665 Interstate DriveCincinnati, OH 45246513-330-6354While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only and should not be considered certified or a guarantee of satisfactory results. Nothing contained herein is to be construed as a warranty or guarantee, express or implied, regarding any matter with respect to this product. Because J Flow Controls® is continually improving and upgrading its product design, the specifications, dimensions and information contained herein aresubject to change without notice.。

SITRANS LPS200 旋转挡板开关商品介绍说明书

SITRANS LPS200 旋转挡板开关商品介绍说明书

Point level measurementOverviewRotation paddle switches / SITRANS LPS200Point level measurementRotation paddle switches / SITRANS LPS200SITRANS LPS200 is a rotary paddle switch for point level and materi­al detection in bulk solids.•Proven paddle switch technology for bulk solids •High integrity mechanical seal•Universal power supply options available•Unique friction clutch mechanism prevents damage from falling material•Rotatable enclosure for convenient wiring•Optional paddles for use with low density materials•Small paddle makes for simple installation through existing pro­cess connection•High temperature model and optional extension kit available •Optional fail-safe configuration detects loss of rotation•Functional Safety (SIL 2). Device suitable for use in accordance with IEC 61508 and IEC 61511The paddle switch technology detects full, empty, or demand condi­tions on materials such as grain, feed, cement, plastic granulate,and wood chips. The paddle switch can handle bulk densities as low as 15.06 g/l (0.94 lb/ft 3) with the optional rectangular vane or 100g/l (6.25 lb/ft 3) with the standard measuring vane.A low revolution geared motor with slip clutch drives a rotating measuring vane which senses the presence of material at themounted level of the LPS200. As material comes into contact with the rotating paddle, rotation stops, which changes the microswitch state. When the paddle is no longer covered by material, rotation resumes and the relay reverts to its normal condition.The LPS200 has a rugged design for use in harsh conditions in the solids industry. The sensitivity of the paddle can be adjusted for varying material properties like buildup on the vane.The LPS200 comes in a variety of configurations including compact,extended and cable extension. It is equipped with a standard vane which is effective in most applications, but can be configured with a hinged or rectangular vane for increased sensitivity for light materi­als.•Key Applications: bulk solids such as grain, feed, cement, plastic granulate, wood chipsLevel Measurement© Siemens AG 2023Level MeasurementPoint level measurementRotation paddle switches / SITRANS LPS200Level MeasurementPoint level measurementRotation paddle switches / SITRANS LPS2001) Available with Approval options C and D only, up to 0.5 bar.Level MeasurementPoint level measurementRotation paddle switches / SITRANS LPS2002) Not available with Process connections A, B, D, E, and G.3) Only available with the following configurations 7ML5725-5AC11-2AD0 or 7ML5725-5EE11-2AC0.4) Only available with the following configurations 7ML5725-6ZC12-2AB0 J2A or 7ML5725-6ZE12-2AA0 J2A.5) Available with Process pressure options 1 and 2 only.6) Available with Process temperature option 1 only.7) Available with Process connection options A ... F only, Process pressure option 1 and Process temperature options 1 and 5 only.8) Available with Process connection options C, F, H … N and Measuring vane options A and B.9) Available with Measuring vane options A, C, D, E, H only.10) Add 16 mm (0.63 inch) to extension length.11) Available with Extension lengths 2, 3, 4, 5.12) Available with Process connection options H … M only.13) Available with Approval option D only.14) Available only with Power supply options J2A, J2B, J2C, and J2D.15) Available up to 250 °C (482 °F).16) Pendulum shaft 500 mm/1 000 mm/1 500 mm should be selected with 150 mm standard length 2 and vane A (35 x 106) to get to the desired lengths.17) Available with Power supply options J2A and J2C only.18) Available with Approval options A, B, C, D, and E only. Approvals A and C with FM only.Level MeasurementPoint level measurement Rotation paddle switches / SITRANS LPS200Level MeasurementPoint level measurementRotation paddle switches / SITRANS LPS2001) Available with Approval options 3 and 4 only and up to max 0.5 bar.2) Not available with Process connection options A, C, E.3) Only available with the following configurations 7ML5726-5ZB12-2BA2 J2A or 7ML5726-5ZC12-2BA1 J2A.4) Available with Process pressure options 1 and 2 only.5) Available with Process temperature option 1 only.6) Available with Process connection options A ... E only, available with process pressure option 1 only, and process temperature option 1 only.7) Extension and vane will also change to 316L, only for Process connection options B, D, F … L and vane A.8) Available with Measuring vane options A, D, E, H only.9) Available with Process pressure option 1 and process temperature option 1 only.10) Available with Process connection options B, D, F … L and vane A.11) Add 16 mm (0.63 inch) to extension length.12) Available with Extension length options 2 … 4 only.13) Available with Process connection options F, G, H, J, K only.14) Available with Approval option 4 only.15) Available only with Power supply options J2A, J2B, J2C, and J2D.16) Available up to 250 °C (482 °F).17) Available with Power supply options J2A and J2C only.18) Available with Extension material Stainless steel, threads 303 option B only.19) Available with Approval options 1, 2, 3, 4, and 5 only. Approvals 1 and 3 with FM only.Level MeasurementPoint level measurement Rotation paddle switches / SITRANS LPS200Level MeasurementPoint level measurementRotation paddle switches / SITRANS LPS2001) Available with Approval options C and D up to max. 0.5 bar.2) Not available with Process connections A, C, E.3) Only available with the following configurations 7ML5727-5ZC12-0AA0 J2A or 7ML5727-5ZB12-0AB0 J2A.4) Available with Process pressure options 1 and 2 only.5) Available with Process connections A ... E only, Process pressure option 1 only and process temperature options 1 and 5 only.6) Add 16 mm (0.63 inch) to extension length.7) Available with Process connections F … K only.8) Available only for Process temperature up to 80 °C (176 °F) and Process connection material 2.9) Available with Approval option D.10) Available only with Power supply options J2A, J2B, J2C, and J2D.11) Available up to 250 °C (482 °F).12) Not available with P01 and available with Approval D, mounting kit for rope extension included.13) Available with Power supply options J2A and J2C only.14) Available with Approval options A, B, C, D, and E only. Approvals A and C with FM only.Level MeasurementPoint level measurementRotation paddle switches / SITRANS LPS2001) Available with Process pressure options 1 and 2 only.2) Available with Approval option D only.3) Available only with Power supply options J2A, J2B, J2C, and J2D.Level MeasurementPoint level measurementRotation paddle switches / SITRANS LPS2004) Available with Power supply options J2A and J2C only.5) Available with Approval options A, B, C, D, and E only. Approvals A and C with FM only.1) Available with Approval options 3 and 4, up to max 0.5 bar.2) Not available with Process connections A, C, E.3) Available with Process pressure options 1 and 2 only.4) Available with Process temperature 1 only.5) Available with Process connections A ... E only, with process pressure option 1 and process temperature option 1 only.6) Available with Process connection options B, D, F … L and measuring vane option A.7) Available with Process pressure 1 and process temperature 1 only.8) Available with Extension length options A … Q only.9) Available with Extension length options R … Y only.10) Available with Process connection options B, D, F … L and Measuring vane A, Process connection material 3. Available only with Extension length options P1A … P1H only.11) Only available with Seal at tube end options P06 (09)12) Add 16 mm (0.63 inch) to extension length.13) Available with Process connections F, G, H, J, K only.14) Available with Approval option 4 only.15) Available only with Power supply options J2A, J2B, J2C, and J2D.16) Available when ordered with Ingress protection seal options P06 … P09 only.17) Available up to 250 °C (482 °F).18) Available with Process pressure option 1 only.19) Available up to 250 °C (482 °F).20) Available with Power supply options J2A and J2C only.21) Available with Approval options 1, 2, 3, 4, and 5 only. Approvals 1 and 3 with FM only.22) Internal probe construction is 1.4305, add seal option P09 to prevent ingress.SITRANS LPS200, dimensions in mm (inch)SITRANS LPS200 connections。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

泵出水口到设备出水口的这段管路中,最好不要 安装在水泵的吸入口的管路上,这样容易使水泵 无法正常吸水,水流开关也无法打开,对于这点 需要特别注意。挡板式水流开关允许水平(塑料
说道:“看在同学一场的份上,你不会说出去的,对不
部分在上)和垂直安装。
注:安装挡板式流量开关时需要注意管道中 的水流方向一定要和流量开关接线盒上的箭头
简介:
ACOL 水流开关是用于电热水器、太阳能热水 器、空调器以及其他水系统的水循环控制、进出
水控制、水加热控制、水泵开关控制、电磁阀通 断控制或出水断电、出水通电控制等过程,当达 到一定流量后将水流转换为开关式电信号的传 感器件。
说道:“看在同学一场的份上,你不会说出去的,对不
水流开关的尺寸 水流开关的安装位置 挡板式流量开关的安装位置一般安装在水
2、使用时请不要扳动塑料壳体,否则将可 能导致相对位置变动促使水流开关不动作。
3、对于应用中的其它问题请致电 ACOL 寻求
支持。
1ct0f5c9d ebet
说道:“看在同学一场的份上,你不会说出的,对不
调整好后将接线盒内的“+”字螺丝锁紧, 盖上前盖板和侧盖板即可。
水流开关应用中问题
1、调试时如果遇到流量开关不闭合时在确 认水流量正常时可以调整流量保护值。判断调节 位置正确与否,可以用手沿水流方向推动挡片, 要使微动开关闭合位置才合适。
说道:“看在同学一场的份上,你不会说出去的,对不
方向一致,否则水流开关无法工作。另外切勿用 手扳动黑色塑料壳,否则流量开关将无法工作。 水流开关流量保护值的调整
说道:“看在同学一场的份上,你不会说出去的,对不
在通常情况下,流量保护值在工厂已经标定 好不需再做调整。
如果现场不得不调整,可以按图 1 将调节螺
丝盖板用力向上移动,露出“+”字螺丝帽;
然后按图 2 打开盖板,拧松接线盒上部的“+” 字螺丝,然后用小号的“+”字螺丝刀拧图 1 露
说道:“看在同学一场的份上,你不会说出去的,对不
出的螺丝帽即可调节流量设定值,顺时针调节减 少流量设定值,逆时针增加流量设定值;
观察图 3 接线盒内部,微动开关组件向右滑
动减少流量设定值,向左滑动增加流量设定值, 但向左滑动过多将可能导致流量开关断开而不 能闭合。
相关文档
最新文档