JX1021TS3轻型货车驱动桥设计

关键词：轻型货车；驱动桥；单级主减速器；差速器；半轴；桥壳
I
黑龙江工程学院本科生毕业设计
ABSTRACT
Pickup trucks take a large proportion of commercial vehicles production, and the drive axle is one of the most important structure. Drive axle is the one of automobile four important assemblies, Its performance directly influence on the entire automobile, especially for the truck .Because using the big power engine with the big driving torque satisfied the need of high speed, heavy-loaded, high efficiency, high benefit today` truck, must exploiting the high driven efficiency single reduction final drive axle is becoming the trucks’ developing tendency. Design a simple, reliable, low cost of the drive axle, can greatly reduce the total cost of vehicle production, so the title of the fine structure of the design of a pickup vehicle drive axle has a certain practical significance. The configuration of the Driving Axle is introduced in the thesis at first. On the basis of the analysis of the structure and the developing process of Driving Axle, the design adopted the Integral Driving Axle, Single Reduction Gear for Main Decelerator’s deceleration form, Spiral Bevel Gear for Main Decelerator’s gear, Full Floating for Axle and Casting Integral Axle Housing for Axle Housing. In the design, we accomplished the design for Double Reduction Gear, tapered Planetary Gear Differential Mechanism, Full Floating Axle, the checking of Axle Housing and the election of the material and so on.
Finally complete the final assembly drawing by using AUTOCAD and mapping the main components.In
this paper, first of all determine the structure of major components and the main design parameters, the analysis of the various parts of the structure of the bridge drive type, the form of the development process and its advantages and disadvantages of the past, determined on the basis of the design program, using the traditional design method of various parts of the drive axle Main reducer, differential, axle, axle housing was designed to calculate and complete the check. Finally compห้องสมุดไป่ตู้ete the final assembly drawing by using AUTOCAD and mapping the main components.
黑龙江工程学院本科生毕业设计
摘
要
轻型汽车在商用汽车生产中占有很大的比重，而且驱动桥在整车中十分重要。驱 动桥作为汽车四大总成之一，它的性能的好坏直接影响整车性能，而对于载货汽车显 得尤为重要。为满足目前当前载货汽车的快速、高效率、高效益需要的同时时，必须 要搭配一个高效、可靠的驱动桥。设计出结构简单、工作可靠、造价低廉的驱动桥， 能大大降低整车生产的总成本的轻型货车驱动桥具有一定的实际意义。 本设计首先论述了驱动桥的总体结构，在分析驱动桥各部分结构型式、发展过程 及其以往形式的优缺点的基础上，确定了总体设计方案：采用整体式驱动桥，主减速 器的减速型式采用单级减速器，主减速器齿轮采用螺旋锥齿轮，差速器采用圆锥行星 齿轮差速器，半轴采用全浮式型式，桥壳采用铸造整体式桥壳。在本次设计中，主要 完成了单级减速器、圆锥行星齿轮差速器、全浮式半轴的设计和桥壳的校核及材料选 取等工作。最后运用 AUTOCAD 完成装配图和主要零件图的绘制。