火电厂常用英语词汇
火力发电厂常用英语词汇.doc
火力发电站常用英语技术词汇induced draught fan: 引风机静电除尘器pulverizer 磨煤机chimney: 烟囱slag pump 灰渣泵boiler house: 锅炉房deaerator: 除氧器thermal cycle: 热力循环coal conveyor 输煤装置feed water tank: 供水箱(net)heat rate: （净）热耗率coal bunker: 煤仓boiler feed pump: 给水泵Assemblie: 集合，集结，组装coal mill 磨煤机switchgear: 开关设备comment 注释，评论steam boiler, water boiler tube 蒸汽锅cable tunnel: 电缆通道module : 模块 standby: 备用炉，管式锅炉 furnace(combustion cable cellar: 电缆槽proximity 相近，接近，亲近chamber): 炉膛 ( 燃烧室 ) turbine room: 汽轮机室detector: 探测器 bracket: 支架water tube: 水管steam turbine with alternator: 蒸汽汽轮interlocks 互锁，联锁 axial: 轴向的ash pit 灰坑发电机组 economizer: 省煤器surge conditions: 喘振 : superheater: 过热器steam drum: 汽包accessory: 附件 pulsation: 有节奏的跳water preheater: 水预热器surface condenser: 表面凝汽动，跳动air preheater: 空气预热器low-pressure preheater: 低压预热器fossil fired: 燃煤 intent: 意图，目的，gas duct(flue): 烟气管 , 烟道circulating water pipe(pump): 循环水管意向dust collecting plant: 集尘室control room: 控制室intend: 意指，想要，打算electrical precipitation plant: 电气除尘室electrostatic dust remover(precipitator): consistent: 一致的，调和的practice: 惯例，实习，实践相关的物质 facilitate: 推动，促进，使Fetting: 附件intrinsic: 固有的，内在的简化Gage:: 规，表，压力计procurement 获得，获取multistage: 多级的Taps: 接头fabrication: 制作，构成，伪造物remote control: 遥控test wells: 测点插孔vent: 通风孔，出烟孔，出口，放出，排safety relief valve: 安全卸压阀stress-relieved: 应力消除出， noncondensible gas: 不凝结气体gauge: 量规，量表，测量thermometer: 恒温计intermittent 间歇的，断断续续的manhole: 人孔，检修孔steam purge system: 蒸汽吹扫系统blowdown : 排污 tank: 桶，箱，罐equivalent: 等价物，相等的centrifugal type pumps: 离心式泵diagram: 图表 deaerator: 除氧器forging:: 锻造 seat: 部位，座friction losses: 磨擦损失corrosion : 侵蚀，腐蚀状态socket welding: 管座焊接solenoid: 螺线管concentration 集中，集合，浓缩，浓度enthalpy: 焓modulat: 调整，调节recommend 推荐，介绍，托付，劝告estimate: 评价，评估，估价criteria: 标准abnormal and normal conditions: 变工况parameters 参数，参量wrenches: 扳手和额定工况 warm up: 暖机nominal : 名义上的，额定的，标称的pipe taps: 管接头 .acid wash: 酸洗MS — Main Steam : 主蒸汽scale: 范围，水垢，水锈，比例，刻度Cycle:: 循环sludge :: 污泥，淤泥 foreign matter: 不Intercept: 截止AX THR BRG :Axis Thrust Bearing:轴向推锅炉最大连续出力BFBP:: Boiler Feed A List of Abbreviations and Symbols in 力，轴承 ATMZ :Atomizing: 雾化Booster Pump: 锅炉给水增压泵English-Chinese AUTO :Automation 自动BNR :Burner: 燃烧器AUX :Auxiliary: 辅助的BOP :Balance Of Plant:电厂辅机设备A ::Ash Handling System: 除灰系统BA :Bottom Ash 底灰BPC :Blade Pitch Control: 叶片节距控制AH :Air Heater: 空气预热器BAH ::Bottom Ash Hopper: 底灰斗BT :Boiler Tube: 炉管AAh :Analyzer, Alarm High : 分析器，高值BLR ::Boiler: 锅炉CH: Crusher House: 碎煤房报警 :: AIV :Air Intake Valve: 进气阀BSD ::Boiler Shut Down: 停炉COMB ::Combustion 燃烧ALIGN Alignment: 校正BUSH :Bushing: 衬套COMP ::Compressed Air: 压缩空气ALKF :Airlock Feeder:锁气器BYPS :Bypass::旁路CONV ::Conveyer: 输送机AP ::Ash Slurry Pump: 灰浆泵BVD ::Boiler Vents and Drains:: 锅炉疏水CPL :Control Pannel Local:就地控制盘ATM :Atmosphere 大气放气 BFP :Boiler Feedwater Pump :: 锅CPM :Control Pannel Main: 主控盘AC ::Air Conditioner: 空气调节器炉给水泵 BFPT:Boiler Feedwater Pump CRT :Cathode Ray Tube:阴极射线管 : AFT :Atmosphere Flash Tank:大气扩容器Turbine: 锅炉给水泵汽机 BFW ::Boiler CT Current Transformer: 变流器AC :Alternating Current: 交流电Feedwater: 锅炉给水CYCL :Cyclone:旋风分离器ALM :Alarm:: 报警BM :Boiler Master 锅炉主控CAS :Casing::缸、壳AMP :Ampere: 安培BMCR:Boiler Maximum Continuous Rating: CB Circuit Breaker: 断路器COMP :Complete: 完成CONDTY :Conductivity: 导电率DSH: Desuperheater: 减温器CCCW:Closed Circulating Cooling Water: CP: Condensate Pump:凝结泵DCA: Drain Cooler Approach: 疏水冷却器闭式循环冷却水 CCW :Cycle Cooling CIR: Circuit: 回路通道 DEAER Deaerator:除氧器Water: 循环水COUPI :Coupling: 联轴器DEV: Deviation: 偏差CCWHF ::Closed Cooling Water Heater闭CP: Condensate Polisher:除盐装置DIFFRLY: Differential Relay:差动继电器式冷却水冷却器 CCWP :Closed Cooling CS: Control Switch 控制开关DISCH VLV :Discharge Valve排放阀WaterPump: 闭式冷却水泵 CS :Closed CRSV:Cold Reheat Safety Valve: 再热器DIST: Disturbance:: 故障、扰动Cooling Water System 闭式冷却水系统冷段安全阀 CV: Control Valve : 控制阀DSCH: Discharge:排出CH Coal Handling 煤的装卸CWP: Circulation Water Pump: 循环水泵ECON: Economizer:: 省煤器CHK VLV :Check Valve:逆止阀DMPR: Damper : 挡板EP Electrical Static Precipitator: 静电除尘CIRC: Circulation: 循环DP Difference Pressure: 差压器CLR Cooler: 冷却器DPIC: Differential Pressure Indicating ECC Eccentricity :: 偏心CLOW :Cooling Water: 冷却水Controller 压差指示控制器DPT: EFF Efficiency: 效率CMPR :Compressor: 压缩机Differential Pressure Transmitter 压差变EHC Electric Hydraulic Control: 电液控制CNTL :Control: 控制送器 DRN: Drain: 疏水EO Electric Operate: 电气操作CNTLE :Controller:: 控制器DV Drain Valve:: 疏水阀EQ Equipment: 设备COND :Condensate: 凝结水DC Direct Current: 直流电ER Error: 误差ES :Extraction System抽气系统FY :Flow Relay or Valve流量传送器GESEGland Steam Condenser Exhauster: ESC Escape:逃逸、超出FA: Failure Alarm: 故障报警轴加风机GMT Generator Main ESS Engineering Safety System:保安系统FD :Forced Draft : 强制通风Trandformer: 发电机变压器GRAD EU Engineering Unit : 工程单位FDF Forced Draft Fan:送风机Grandient: 梯度EXH Exhaust:排汽FIC :Flow Indicate Controller: 流量指示控GS :Gland Steam: 轴封蒸汽EXT Extract: 抽出制器 FLT :Flash Tank :扩容箱GSC :Gland Steam Condenser: 轴封加热FA :Fine Ash: 细灰FLD :Field 磁场器 GV :Governor Valve: 高压调门FDR Feeder: 给料机FLG :Flange: 法兰H ::Heat Conservation 保温FE :Flow Element:: 流量元件FLM Flame: 火焰HS: Hand Switch:: 手动开关FI :Flow Indicator:: 流量指示件FWH Feed Water Heater 给水加热器HTR Heater: 加热器FDBK: Feedback:反馈FO :Fuel Oil: 燃油HV: Hand Control Valve: 手动控制器FITG Fitting: 连接件FREQ Frequency:频率HY: Hand Relay or Transducer 手动继电FLW Flow 流量FURN Furnace: 炉膛器（转换器）H :Hand: 手动的FO :Fail Open: 故障时自动打开GLD Gland: 密封HB :Heat Balance: 热平衡FT: Flow Totalizer: 流量累加器GRDR Grinder: 碎渣机HD :Heater Drain:: 加热器疏水FT :Flow transmitter: 流量变送器GND Grounding: 接地HDR :Header: 联箱FV :Flow Control Valve 流量控制阀GC :Generator Cooling: 发电机冷却HL ::Heat Loss: 热损失HMDY Humidity: 湿度IDF ::Induced Draft Fan: 引风机:Low Point : 低位HPH: High Pressure Heater:高压加热器IGN ::Ignition: 点火装置LPH: Low Pressure Heater:低压加热器HPR :Hooper: 漏斗INLT :Inlet: 入口LSH: Local Switch Hand:就地开关HPT :High Pressure Turbine:高压汽机IPR ::Initial Pressure: 初压LUB: Lubricating Oil: 润滑油HR: Hot Reheat: 再热器热段INST :Instrument: 仪表M :Mechanical: 机械HR: Heat Rate: 热耗率INVR :Inverter: 逆变器M :Motor: 马达HSV: Hot Reheat Safety Valve: 再热器热I /O:: Input/Output 输入 / 输出MAG:: Magnetic: : 磁性段安全阀HVAC :Heating Ventilation IP :Intermediate Pressure: 中压MOD ::Mode: 方式 :& Air Conditioning:: 暖通ISV ::Intermediate Pressure Turbine Steam M/A :Manual/Automatic: 手动/ 自动HW :Hotwell: 热井Valve: 中压缸进汽阀 JP :Jet Pump: 喷MAN ::Manual :: 手动HV ::Hand Control Valve: 手动控制器射器MARG: Margin:: 裕量HYD :Hydraulic: 液力的LG :Level Gauge液位计MAX ::Maximum: 最大的，最大值的INTLK :Interlock : 联锁LVL ::Level: 水位，液位MCR ::Maximum Continuous Rating 最大IC :Instrument and Control:: 仪表与控制LA :Level Alarm: 液位报警连续出力 MCV:: Main Control Valve: 主（热工） ICV ::Inrtermediate Control LIM(LMIR): Limiter: 限制器控制阀Valve 中压控制阀 ID :Induced Draft 抽LKG:: Leakage::泄漏MD :Modulation Damper: 调节挡板风，引风LP :Low Pressure 低压MDBFP: Motor Driven Boiler FeedwaterPump: 电动给水泵 MEAS ::Measure : OPER :Operation: 运行PERFCALC Performance Calculation:: 性测量OSC :Oscillograph: 示波器能计算 PF: Power Factor 功率因数MFT: Master Fuel Trip: 主燃料跳闸OTLT: Outlet: 出口PHTR: Preheater: 预热器MIN :Minimum: 最小的PA: Primary Air: 一次风PMP :Pump: 泵MKUP (MU) Make-up: 补充PAF :Primary Air Fan: 一次风机PNEU :Pneumatic: 气动的ML :Mill: 磨煤机PAH :Pressure Alarm High:高压报警PR: Pressure Recorder:压力记录计MN :Main: 主要的PAL :Pressure Alarm Low:低压报警PRG :Purge: 吹扫. :Manual Operation: 手操PB: Push Button 按钮PRV :Pressure Relief Valve:泄压阀MPT :Main Power Transformer: 主变压PC :Power Centre: 动力中心PRO :Protection: 保护器PC: Pressure Controller: 压力控制器PROGR:: Program:程序MS :Main Steam 主蒸汽. :Pressure Control: 压力控制PT: Pressure Transmitter: 压力变送器MSV :Main Steam Valve: 主汽阀PCP :Precipitator 除尘器PULV: Pulverizer: 磨煤机NOZ: Nozzle: 喷嘴PCV :Pressure Control Valve:: 压力控制PVSV :Pressure Vacuum Safety Valve 压NPSH :Net Pump Suction Head:泵的静吸阀 PDI :Pressure Differential Indication: 力真空安全阀 PW: Plant Water 厂用水压头差压指示 PDT :Pressure Differential PY: Pressure Relay:压力继电器OL: Overload: 过载Trandsmitter: 差压变送器 PED :Pdestal:: QA: Quality:: 质量，性能OLR :Overload Relay:过载继电器轴承座RB: Run Back: 快速降负荷RCV :Recovering:回收SLS :Seals::密封TBFP Turbine Drive Boiler Feedwater RECIRC:: Recirculation再循环SO: Shut Off: 关闭Pump 汽泵 TCV :Temperature Control RECT :Rectifier: 整流器SPD :Speed: 转速Valve 温度控制RET :Return: 返回SPRA: Spray:喷水.: Transfer Damper: 转换挡板RH: Reheater: 再热器SPT :Support: 支持 : TE: Temperature Element: 温度元件RO: Restriction Orifice: 节流孔板ST: Start: 启动，开始TG: Turbine-generator: 汽轮发电机ROT :Rotor: 转子STD-BY :Stand By:备用Turbine-gear: Turbine-gear: 汽机盘车RTU :Remote Telemetry Unit:: 遥测装置ST: System:: 系统THERM :Thermal 热力的SA :Secondary Air: 二次风STM :Steam: 蒸汽TMS: Turbine Master System: 汽机主控SAT: Saturate: 饱和的STR: Stator:: 定子系统 TRANS :Transfer:转换SC :Steam Coil Air Heater::暖风器STRNR: Strainer:滤器TRBL: Trouble: 故障SCAV :Scavenge:吹扫SU: Start Up: 启动TRKG: Tracking:跟踪SD: Shut-off Damper: 关断挡板 : SV: Solenoid Valve: 电磁阀TT: Temperature Transmitter: 温度变送Shut-Down 停机SUCT: Suction: 吸入器分离器SW: Switch: 开关:TTD: Terminal Temperature Difference:SEP :SeparatorSG: Switchgear 开关装置Steam Water: 汽水温度端差SH: Superheater: 过热器SBLWR: Soot Blower吹灰器TW: Thermowell: 热电偶套管UAM :Unit Automatic Master: 机组自动手动 ;系统ALARM 报警 ;VAC: Vacuum: 真空AUX ： AUXILIARY ::辅助 ;VAL: Value: 数值BYPASS旁路VB: Vibration 振动 VLV: Valve: 阀门CLOSE关（状态，常指阀门）; WH: Watthour 瓦小时CODE: 代码；编码WP: Working Point: 工作点COLD START— UP: 冷态启动WW: Water Wall 水冷壁COMPUTER :计算机WX: Watt Transducer: 功率转换器CURVE ， LINE: 曲线，线COVER :Crossover切换管DATA: 数据；文件；资料CV: Control Valve: 控制阀DECREAS 减:少DESK: 台，桌英汉对照表DIGIT: 数字DISK: 磁盘A/H ： AUTOMATION/HAND : 自动 / 手DYNAMIC ； DYNAMICAL: 动态动 ; F ： FLOW流量 ;A/M ： AUTOMATION/MANUAL: 自动 / FAST: 快FIGURE: 图示HIGH: 高HOT START— UP: 热态启动I＆C ：INSTRUMENT AND CONTROL仪表与控制INCREAS:增加INDICATION ； DISPLAY :指示；显示; INLET 入口;INPUT 输入 ;INTERMEDIATE中KEYBOARD:键盘KW ： KILOWATT 千瓦L ： LOAD 负荷，负载;LOC ： LOCAL :就地LOW:低MCS ：MANAGMENT COMMAND SYSTEM 管理命令系统MODE : 方式，模式R ： RESISTANCE:电阻 ; STOP: 停止 ;MW ： MEGAWATT 兆瓦REM ： REMOTE : 摇控 ; SYMBOL 符号NORMAL: 正常RESET复位SYSTEM:系统OFF : 关（状态） ; ROOM : 室T ： TEMPERATURE:: 温度 ;ON : 开（状态） ; RPM::转/ 分; TEST: 试验 ;OPEN: 开( 状态，常指阀门 ); S ： SPEED速度 ; TRANSMITTIER;TRANSDUCER:变送器；传OPERATE :运行；操作 ; SELECT选择感器OUTLET 出口 ; SET POINT设定点TRIP 跳闸 ;OUTPUT 输出 ; SHUTDOWN : 停机 ; TRIP ACKNOW: 跳闸确认P ： PRESSURE:压力 ; SIDE （某）侧，边 ; UNAVAIL 不允许 ( 不能投用的 ) PANEL 盘SILENCER消音器UNIT : 单元、机组PARAMETER :参数SLOW : 慢VALVE 阀门PIPE ； TUBE: 管道，管子STAND BY:备用 ; WARM START— UP: 温态启动PLANT: 厂，站START : 启动 ; ZOOM: 摄像机镜头POWER: 功率，电源 ; STARTUP :起动；启动 ;PRINT: 打印STATIC 静态锅炉部分R ： RATE : 比率，速率 ; STATION 站ACTUAL MEGAWATT: 有功AIR DRAFT SEQUENCE: 风机程序控制（顺控）AIR HEATER A MOTER: 空预器马达 A AIR HEATERLOC/REM SELECT:空预器就地 / 遥控选择AIR HEATERMOTOR LEAD: 空预器马达选择AIR HTR A SEC AIR OUT TEM 空预器 A 二次风出口温度AIR PREHEATER:空预器AIR SVCE SUPPLY:服务空气ALARM LIMITS: ::报警限制ALL AIR HTRS RUNNING各空预器运行ALL PULV GRP SHUTDOWN所有磨组停运ASH— HOPPER: :灰斗ATTEMPERATOR: 减:温器CLEAN:清扫AUX .ST: SPLYFOR ATOMIZ 辅助蒸汽供COAL BANKER: ::煤仓雾化蒸汽COAL FEEDER给:煤机BOIL MILL A BNR MET TEMP 炉 A 磨组COMBUSTION :燃烧喷燃器金属温度CONVEYOR:皮带机BOIL MILL A GR1 WDBOX PR 炉 A 磨组COORDINATE MODE 协调方式第一组风箱压力CRUSHER:破碎机BOILER AIR REQUIRED 锅炉风量需求DECR/INCRPRESSAT FIX LOAD:: 固定负（ >30% ）荷方式增减压力BOILEREFFLUENTSTORAGE:POOL 锅炉DOWM COMER:: 下降管废水池DRAIN & VENT:疏水和排气BOILER FOLLOW MODE: 炉跟随方式ECONOMIZER :省煤器BOILER MASTER:锅炉主控器EITHER FAN RUNNING任:一风机运行BOILER TRIP RESET:锅:炉跳闸复位EITHERID FAN RUNNING任一吸风机BOILER:锅炉运行BURNNER: :燃烧器ELECTROSTATICPRECIPITATOR: 静电除CHIMNEY ； STACK:: :烟囱尘器FD FAN A FLOW:: A送风机流量INDUCED DRAFT FAN引:风机MANUAL MODE: 手动方式FD FAN/ID FAN A CONT DAMPERA 送 / INDUCED&FORCEDDRAFTS:吸送风MANUAL THROTTELPRESSSET POINT:手吸风机控制挡板机动节流压力设定值FEED WATER FLOW: 给水流量INITIATE: 启动、引燃、激发、触发MILL A GROUP MASTER : 磨A组主控器FEEDERLOCAL SELECT:给煤机就地控制ISOLATION:隔离；绝缘MILL A LOAD: A磨组负荷选择LFO .DISCH .PRESS轻:油出口压力MILL A OUT TEMP CONT DAMPER : A 磨FEEDERREMOTE SELECT:给煤机遥控选LIGHT OIL SEL GRP 第1:一组轻油枪选择组出口温度控制挡板择LIGHT OIL: 轻油MIN MAX LOAD （ LIMITS ） : 最大最FLUE GAS:烟气LUB OIL PUMP::润滑油泵小负荷（限制）FORCED DRAFT FAN送:风机MAIN STEAM STOP VLV: 主蒸汽截止MMMC ＝ MILLIMETER MERCURY ；FUEL GAS ID FAN A OUTLET PRESS吸风A 阀MMH2O: 毫米汞柱；毫米水柱机出口压力MAIN STEAM TEMP/PRESSURE/FLOW O 2 IN THE FUEL GAS烟气含氧量FURNACE PRESS:炉膛压力主汽温度 / 压力 / 流量OPEN/CLOSESWING VLVS 摆阀开/ FURNACE: 炉膛MAINTAINED IGNITORSPULVERIZERA:磨关GAS COAL: ::烟煤煤机 A 油枪操作OPERATEMODE SELECT: 运行方式选HEADER :联箱、母管MANUAL LOAD SET/RATE:手动负荷设定择IGNITOR: : 点火器，油枪/ 负荷率PENDANT: : 悬吊管PLATEN SPARY CONTROL VLVS SIDE 屏A :过减温水 A 侧控制阀PLATEN SUPERHEATER:屏过PRESSURE DIFFERENCE:压差PRI AIR DUCT PRESS 一次风管压力PRI AIR FAN A CONT DAMPER: A 侧一次风机控制挡板PRI AIR FAN A OUTLET PRESS 一A 次风机出口压力PRI AIR FLOW MILL A CONT DAMPER 磨组一次风控制挡板PRI/SECAIR FLOW MILL A A 磨组一次 /二次风流量PRIMARY AIR FAN: 一次风机PRIMARY AIR SEQUENCE:一次风控制PULVERIZER 磨:煤机PULVERIZEREMERGENCETRIP 磨煤机紧急跳闸磨组二次风流量控制挡板PULVERIZER INERT MODE SELECT:磨煤 SEC SH OUT STEAM TEM 二级过热器出机惰性方式选择口蒸汽温度PULVERIZER NORMAL MODE SELECT: SEC SH SPARY CONT VLVS SIDE A 二级磨煤机正常方式选择过热器减温水 A 侧控制阀PULVERIZER SELECTION A 磨::煤机A 选 SECONDARYSH INLET TEMP 二级过热器择进口温度PULVERIZER:M/A: SELECT 磨煤机手 /SECONDARY: AIR 二次风自动选择SH； SUPERHEATER:过:热器PURGE 吹扫SH STEAM ELECTR VLV:过热器电磁阀RH； REHEATER:再热器SH STEAM TEMP SET POINT::过热温度设SAFETY VALVE::安全阀定点SCANNER BLOWERS:火检吹扫器SH/RH SPARY WATER STOP VLVS::过热器SEAL AIR FAN PRESS:密封风机压力/ 再热器减温水截止阀SEAL AIR FAN:: 密:封风机 SH/RH SPRAYCONTROLVLVS SELECT过SEC AIR DUCT PRESS:二次风管压力 热器 / 再热器减温水控制阀选择SECAIR FLOW MILL A CONT DAMPER A SLIDING PRESS MODE: 滑压运行方式STOP/STARTPA FLOW:一次风停止/ SOOT BLOWER:吹灰器SPARK火花，点火花SPEEDCHANGE(NOT) PERMISSIVE:速度切换（不）允许SPRAY :喷水STACKER RECLAIMER堆::取料机START IGNITOR GRP 第1:一组油枪点火STEAM DRUM: :汽包STEAM 蒸汽STONE COAL:无烟煤STOP IGNITORS GRP 第1:一组油枪停止STOP/START FEEDER 给煤机停止/ 启动STOP/STARTIGNITORS: 油枪停止/启动STOP/START MILL:磨组停止 / 启动启动汽机部分WATERWALL: :水冷壁BLADE 叶片STOP/STARTPULVERIZER磨煤机停止:EMERG OIL PUMP:事故油泵/ 启动<P>CICR PMP DISCHARGE VLV:循环泵出STOP/STARTSEQUENCEPULVERIZERA:口阀磨煤机 A 程序停止/ 启动1ST STAGE PRESS:第一级压力THROTTLE PRESS::节流压力ACTUAL MEGA WATT: 实:际负荷数TRANSPORTAIR SEQUENCE风量程序控AMS ： ADMISSION: MODE SELECTION制（顺控）进汽方式选择TURB FIRST STAGE PRESS汽机第一级AUX STEAM HEADER:辅:汽联箱( 调节级) 压力AUX STEAM TEMP CONTROL:辅汽温度TURBINE FOLLOW MODE: 机跟随方式控制TURBINE MASTER:汽机主控器AUX STM HEADERPRESSCONTROLVLVTWIN FLOW AIR HTR A CONT VLV:双:流辅汽联箱压力控制阀式空预器控制阀BALANCE: :平衡UNLOADER: ::卸煤机BEARING BRASS::轴瓦WATER 水BEARING: : 轴承BOILER FOLLOW MODE:锅炉跟随方式BOOSTER FEED PUMP: 前置给水泵CICR WTR PUMP:循环泵CIRCULATING PUMP: 循:环泵CIRCULATING:循环CLOSED COOLING WATER:闭式冷却水CLOSEDCOOLINGWTR PUMP: 闭式冷却水泵CMPTR: : 计数器CONDENSATE PUMP:凝泵CONDENSER AIR SUCTION VLV:凝汽器抽空气阀CONDENSER HOT WELL:热:井CONDENSERLEVEL CONTROLVLV: 凝汽器水位控制阀CONDENSER:凝汽器CONDSEXTRPUMP DISCH: 凝结水抽吸泵出口CONDS STOR TANK LEVEL:凝结水储水箱水位COOLER: :冷却器COOLNG WTR PUMP:水冷泵COORDINATE MODE: 协:调方式CV ： CONTROL VALVE高压调门CYLINDER、 CASING: 汽缸DEAERATORLEVEL CONTROLVLV: 除氧器水位控制阀DEAERATOR: 除:氧器DECR PRESS AT FIX LOAD:在负荷不变下减压DEMI WATER: 除盐水DISPATCHPARTICIPATION调度（参与）指令DURM PRESSURE::汽包压力EJECTOR:喷射器，抽气器EMERGENCY GOVERNOR危急保安器EXHAUST:排汽EXPANSION:膨胀EXTR ST TO HP HTR抽汽至高加EXTRACTION STEAM抽汽FILTER: :滤网FLANGE 法兰FUNCTION GROUP:功能组FW CONTROLVALVE' S BYPASSVLV: 给水控制阀的旁路阀FW FLOW 30% CONTROL VLV : 30%给水控制阀FW FLOW MASTER CONTROL:给水流量主控FW HP HTR DISCH TEMP: 给水高加出口温度FW PUMP RECIRCULCONTROLVLV 给水泵循环控制阀FW VLV: 给水阀门GEARING: 盘车GOVERNOR:调速器HP ATTEM PRESSCONTROLVLV: 高旁减温水压力控制阀HP ATTEMP BLOCK VLV:高旁减温水闭锁阀HP BYPASS ＆ HP ATTEMP VLVS:高压旁路及减温水阀HP BYPASSPRESSCONTROLVLV 高旁压力控制阀HP BYPASSPRESSSET POINT: 高旁压力设定值HP BYPASSTEMP CONTROLVALVE 高旁温度控制阀HP＆LP BYPASSCOMMAND 高压及低压LUBE OIL PUMP:润滑油泵旁路指令MAKE － UP WATER: 补给水HPH ： HIGH PRESSURE HEATER高加:MANUAL LOAD RATE手动负荷率HYDRAULICOIL STATIONPUMP: 液压油MANUAL LOAD SET手动负荷设定站泵MANUAL Throttle Press Set Point 手动节INCR PRESSAT FIX LOAD: 在负荷不变下流压力设定值增压MEASURE SELECTION测量选择站INT POS: 中间状态MOP ： MAIN OIL PUMP: 主油泵IV ： INTERMEDIATE VALVE中压联合汽MOTOR DRIVEN FEED WATER PUMP电动门给水泵JACKING OIL PUMP顶轴油泵MSV ： MAIN STOP VALVE:主汽阀LP HTR STOP VLV低加截止阀NOZZLE 喷嘴LP ＆ HP BYPASSPRESSSIDE A 低压或OIL PURIFIER:净油器高压旁路 A 侧压力OIL STORAGE TANK储:油箱LP ＆ HP BYPASS TEMP SIDE低A压或高OPERATE MANUAL MODE:手动方式压旁路 A 侧温度OPERATE MODE SELECT:运行方式选择LPH ： LOW PRESSURE HEATER:低加PILOT VALVE:错油门PLATEN SH INLET TEMP SIDE A:侧A屏过SPEED INDICATOR OR SPEED METER:转 : TURBINE GENERATOR:汽轮发电机组入口温度速表TURBINE INLET PRESS:汽机入口压力PRIMARY SH STOP VALVE:一级过热器截STATOR定子TURBINE MASTER 汽:机主控器止阀STEAM TURBINE 汽:轮机TURBING FOLLOW MODE:汽机跟随方式PUMP A DISCH PRESS :泵A出口压力ST － UP BOIL FDW PUMP:启动给水泵VACCUM 真空RH SPRAY BLOCK VLVSTRIP INIT再热器喷SUCTION PUMP: 抽吸泵VACUUM BROKEN VALVE:真空破坏门水闭锁阀跳闸启动SURGE APPROACH:喘振VACUUM SEQ :真空程控RH SPRAYWTR STOP VLVS: 再热器喷水SYNCHRONIZER:同步器VIBRATION: 振动截止阀TFW PMP DISCHARGEVLV: 汽动泵出口电液调节及控制部分RH STEAM ATTEM FLOW:再热喷水流量阀1STAGE PRESSUREFEEDBACK:第一级压RH STEAM TEMP OUTLET:再热器出口温TFW PUMP MAIN OIL PMP: 汽动给水泵力反馈度的主油泵ABNORMAL CONDITION:异常状态ROTOR 转子THROTTLE ORIFICE 节流孔板ACCELERATION:加速度SEAL: 密封TURBINE DRIVEN FEED WATER PUMP:汽ACTIVE POWER::有功功率SHAFT 轴动给水泵ADMISSION MODE: 进汽方式SILENCER: 消音器TURBINE FW PUMP AUX＆ VLV 小机给ADS(ALARMDISPLAYSELECTPANELS)报SLIDING PRESS MODE:滑压方式水泵辅汽及阀门警显示选择屏AERIAL LINE:架空线BACK UP TRANSFORMER备用变BUSHING 套管ALTERNATING CURRENT (AC):交流BACK-UP OVERSPEEDTRIP TEST 备用超CABLE 电缆AMPERE: 安培速跳闸试验 ELECTRICALTRIP TEST 电CAPACITANCE: 电容ANGLE OF LAG:滞后角气跳闸试验CARRIER 载波ANGLE OF LEAD:超前角BACK-UP SPDSIG LOST:后:备速度信号失CATHODE : 阴极ANODE: 阳极去CCR: 中控室ARC: 电弧BARRING OIL PUMP盘车油泵CHARGING EQUIPMENT : 充电设备ARMATURE 电枢BASE LOAD:基荷CHEST/ROTOR WARMING: 腔室 / 转AST ： AUTO SHUT-DOWN TRIP:自动停BATTERY :电池子预暖机遮断BATTERY BACKED CLOCK电池备用时钟CIU : 计算机接口单元ASYNCHRONOUS MOTOR:异步电动机BDV ： BLOWDOWN VLV:泄放阀CLOSE :合闸AT SET SPEED: 在设定速度位置BOOSTER PUMP:前置泵CLOSED VALVES OVERSPEED TEST关闭阀ATC ： AUTO TURBINE CONTROL:自动汽BULB : : 灯泡超速轮机控制BUS SECTION : 母线分段CLOSED-LOOP 闭:环AUTOFORMER:自藕变BUS: 母线COIL:: 线圈AUTORECLOSING自:动重合闸BUSBAR FRAME:母线架COMBINED RECLOSING综合重合闸AUXI TRANSFORMER厂:用变BUSCOUPLER: 母联COMBINED REHEAT VALVES:中压联合阀COMMON SERVICESLOGIC SUITE:: 公用DISCONNECTOR 隔:离开关EXCITOR 励磁机系统逻辑柜DISTRIBUTEDCONTROLSYSTEM:分散控FA/PA POSITION : 全周 / 部分（进汽）COMMUNICATION: 通讯制系统位置CONDUCTOR : 导体工程师工作站FAST-ACTING SOLENOID:快动电磁阀CONFIGURATION:结构，布置，外形 : EHC STATUS:电液调节系统状态FIRST STAGE PRESS调节级压力CONTROL OIL:控制油EHC ：ELECTRO-HYDRACONTROL FIS :: 流量显示开关CORE: 铁芯SYSTEM:电液调节控制系统FREQUENCY: 频率CPU(CENTARL PROCESSING UNIT:中心处EHV MIMIC PANEL :电气高压模拟屏FRF ： FIRE RESISTANT FLUID::抗燃油理单元ELECTRICAL MALFUNCTION SYSTEM FULL ARC : 全周进汽CRT: 显示屏FAULT : 电气失灵系统故障GAS : 瓦斯CURRENT TRANSFORMER:电流互感器EMERGENCY OIL PUMP:事故油泵GEN. SHAFT SEAL&STATORWIND : CURRENT电流EMERGENCYSEAL OIL PUMP: 事故密封发电机密封及静子绕组CV:: 控制阀油泵GENERATOR 发:电机DAS: 数据采集系统ETS ： EMERGENCYTRIP SYSTEM:危急GROUNDING(EARTHING)接地DECREASING LOAD RATE:减:负荷率跳闸系统H2 TEMP CONT V :氢气温度控制阀DIESEL GENERATOR柴:油发电机EXCEPTION REPORT:例外报告HARDWARE硬件DIRECT CURRENT (DC)直流EXCITE 励磁HOLD: 保持HYDRAULIC FLUID PRESS:抗燃油压力荷减；在设定负荷MAIN STEAM PRESS 主蒸汽压力数字控制站终端模件LOAD FLOW :负荷潮流分布MAIN TRANSFORMERSTEP-UPIN STANDBY:在备用状态LOAD INCREASING:负荷增TRANSFORMER:主变IND: :: 指示器LOAD LIMITING SET: 负荷极限设定MANUAL: 手动INDUCTANCE: 电感LOAD MONITORING: 负荷监视MCC: 马达控制中心INHIBITED: 停止进行、禁止LOAD SELECT: 负::荷选择MEGAWATT: 兆瓦INSULATOR绝缘子LOAD SET: 负荷设定MFP : 多功能控制器INTERCEPT VALVE:中间截流阀LOAD: 负荷MOTOR: 电动机INTERCEPT VALVES:中间截止阀LOADING RATE LIMIT : 负荷（增、减）MSPL ： MAIN STEAM PRESSURE LIMITER : INTERFACE接口率限定主汽压力限制器KILOWATT 千瓦LOCKED OUT:闭锁MSV: 主蒸汽阀LC: 液位控制器LOSS : 损耗NEUTRAL POINT:中性点LI: 液位显示LOSS OF PWR:: 失去电源OHM: 欧姆LIGHT: 照明LVDT ：线性位移差动变送器OIL GAUGE:油位表LINE 线路MAGNETIC FIELD: 磁场OPC ：OVERSPEED PROTECTION LK: 液位控制站MAIN OIL PUMP: 主油泵CONTROL:超速保护控制LOAD DECREASING ； AT SET LOAD负MAIN SEAL OIL PMP 主:密封油泵OPEN-LOOP :开环OPER AUTO:操作员自动 :: PHASE ANGLE 相:角RECLOSING : 重合闸OPERATING MODE 操:作方式PHASE: 相REHEAT PRESS:: 再热汽压力ORP ： OIL RESET PISTON:油复位活塞PIC: 压力显示控制器REMOTE AUTO:远方自动ORSV ： OIL RESET SOLENOID VLV油复PK: 压力控制站REMOTE OPERATION远:操位电磁阀PLUG : 插头RESISTANCE: 电阻OTSV ： OIL TRIP SOLENOID VLV:油跳闸PLUG SOCKET:插座RSM ： ROTOR STRESS MONITORING:转电磁阀POLE:: 电极子热应力监视 :OVER CURRENT:过流POTENTIAL TRANSFORMER电压互感器RSV: 再热汽截止阀OVER VOLTAGE 过:压POWER 功率SAFELY OIL 安:全油OVERLOAD: 过载POWER FACTOR:功率因数SCR CONTROLLER:可控硅整流控制器PART ARC 部:分进汽POWER LOAD UNBALANCE:功载不平衡SEAL OIL:密封油PC: 动力中心PP ： : PREESSURE POINT压力检测点SHUT-OFF VALVE::切断阀PDIS : 压差显示开关PRI SPD SIG LOST 一次速度信号失去SIGNAL: 信号PEAK LOAD:峰荷PS: 压力开关SLOW MEDIUM FAST:慢、中、快PERMANENT MAGNETIC GENERATORDFPT: 压力变送器速度增SPEED INCREASING:永磁发电机REACTANCE: 电抗SPEED MONITORING:速度监视PG: 压力计REACTIVE POWER:无功功率SPEED SET RPM转:速设定转 / 分SPEED:速度，转速START UP TRANSFORMER启动变STATORWIND COOLING WATER PUMP: 定子绕组冷却水泵STEAM SEAL BY-PASS UNLOAD VLV:蒸汽密封旁路泄放阀STEAM SEAL DIVERINGVALV: 密封汽分流阀STEAM SEAL SYS::蒸汽密封系统SUCTIONPMP A/M SEL: 抽吸泵手/ 自动选择THERMO-COUPLE: 热:电偶THREE ELEMENTS LEVEL CONTROLLER:三冲量水位控制器THRUSTBEARINGWEAR DETECTORTEST推力轴承磨擦检测试验TI : 温度显示器TIC :: 温度指示控制TIME DELAY:时间延迟TP: 温度检测点TRANSFERAND FILTERPUMP: 输送和过滤油TURB LUBE OIL TEMP CONTROL V汽:机润滑油温度控制阀TURBIN DRAIN VALVES: 汽机疏水阀TURBINE LATCHED:汽机挂闸TURN GEAR CONTROL SEQUENCE盘车控制程序TURN GEAR MOTOR:盘车主电机TURN GEAR PIGGY: BACK MOTOR盘车啮合电机UNINTERRUPTEDPOWER SUPPLY:不间断电源SUCTION PUMP:抽吸泵TRANSFORMER: 变压器SUPERVISORS DESK:值长台TRANSMISSION:传输SWITCH开关TRIP 跳闸UNIT CONTROL DESK:机组控制台UNIT TRANSFORMER::单元变VACUUM TRIP:真空跳闸SWITCHGEAR : 配:电盘、开关装置TS: 温度开关VALVE POSITION:阀位置TELEPHONE: 电话TSI: 汽机监视仪表VI : 阀位置指示TEST SELECT:试验选择（联锁）TT:: 温度变送器VOLT(V): 伏特VOLTAGE电压VT: 阀位置变送器VV ： VENTILATING VALVE通:风阀WARMING RATE:暖机速率WATT:瓦特WINDING: 绕组。
火力发电厂常用英语词汇
火力发电站常用英语技术词汇boiler house: 锅炉房coal conveyor 输煤装置coal bunker: 煤仓coal mill磨煤机steam boiler, water boiler tube 蒸汽锅炉，管式锅炉furnace(combustion chamber): 炉膛( 燃烧室)water tube: 水管ash pit 灰坑superheater: 过热器water preheater: 水预热器air preheater: 空气预热器gas duct(flue): 烟气管, 烟道dust collecting plant: 集尘室electrical precipitation plant: 电气除尘室induced draught fan: 引风机chimney: 烟囱deaerator: 除氧器feed water tank: 供水箱boiler feed pump: 给水泵switchgear: 开关设备cable tunnel: 电缆通道cable cellar: 电缆槽turbine room: 汽轮机室steam turbine with alternator: 蒸汽汽轮发电机组economizer: 省煤器steam drum: 汽包surface condenser: 表面凝汽low-pressure preheater: 低压预热器circulating water pipe(pump): 循环水管control room: 控制室electrostatic dust remover(precipitator):静电除尘器pulverizer 磨煤机slag pump 灰渣泵thermal cycle: 热力循环(net)heat rate: （净）热耗率Assemblie: 集合，集结，组装comment 注释，评论module : 模块standby: 备用proximity 相近，接近，亲近detector: 探测器bracket: 支架interlocks 互锁，联锁axial: 轴向的surge conditions: 喘振:accessory: 附件pulsation: 有节奏的跳动，跳动fossil fired: 燃煤intent: 意图，目的，意向intend: 意指，想要，打算consistent: 一致的，调和的practice: 惯例，实习，实践intrinsic: 固有的，内在的procurement 获得，获取fabrication: 制作，构成，伪造物vent: 通风孔，出烟孔，出口，放出，排出，noncondensible gas: 不凝结气体intermittent 间歇的，断断续续的blowdown : 排污tank: 桶，箱，罐diagram: 图表deaerator: 除氧器corrosion : 侵蚀，腐蚀状态concentration 集中，集合，浓缩，浓度recommend 推荐，介绍，托付，劝告abnormal and normal conditions: 变工况和额定工况warm up: 暖机acid wash: 酸洗scale: 范围，水垢，水锈，比例，刻度sludge :: 污泥，淤泥foreign matter: 不相关的物质facilitate: 推动，促进，使简化multistage: 多级的remote control: 遥控safety relief valve: 安全卸压阀gauge: 量规，量表，测量manhole: 人孔，检修孔equivalent: 等价物，相等的forging:: 锻造seat: 部位，座socket welding: 管座焊接enthalpy: 焓estimate: 评价，评估，估价parameters 参数，参量nominal : 名义上的，额定的，标称的MS — Main Steam : 主蒸汽Cycle:: 循环Intercept: 截止Fetting: 附件Gage:: 规，表，压力计Taps: 接头test wells: 测点插孔stress-relieved: 应力消除thermometer: 恒温计steam purge system: 蒸汽吹扫系统centrifugal type pumps: 离心式泵friction losses: 磨擦损失solenoid: 螺线管modulat: 调整，调节criteria: 标准wrenches: 扳手pipe taps: 管接头.A List of Abbreviations and Symbols in English-ChineseA ::Ash Handling System: 除灰系统AH :Air Heater: 空气预热器AAh :Analyzer, Alarm High : 分析器，高值报警:: AIV :Air Intake Valve: 进气阀ALIGN Alignment: 校正ALKF :Airlock Feeder: 锁气器AP ::Ash Slurry Pump: 灰浆泵ATM :Atmosphere 大气AC ::Air Conditioner: 空气调节器AFT :Atmosphere Flash Tank: 大气扩容器AC :Alternating Current: 交流电ALM :Alarm:: 报警AMP :Ampere: 安培AX THR BRG :Axis Thrust Bearing: 轴向推力，轴承ATMZ :Atomizing: 雾化AUTO :Automation 自动AUX :Auxiliary: 辅助的BA :Bottom Ash 底灰BAH ::Bottom Ash Hopper: 底灰斗BLR ::Boiler: 锅炉BSD ::Boiler Shut Down: 停炉BUSH :Bushing: 衬套BYPS :Bypass:: 旁路BVD ::Boiler Vents and Drains:: 锅炉疏水放气BFP :Boiler Feedwater Pump ::锅炉给水泵BFPT:Boiler FeedwaterPump Turbine: 锅炉给水泵汽机BFW ::Boiler Feedwater: 锅炉给水BM :Boiler Master 锅炉主控BMCR:Boiler Maximum ContinuousRating: 锅炉最大连续出力BFBP::Boiler Feed Booster Pump: 锅炉给水增压泵BNR :Burner: 燃烧器BOP :Balance Of Plant: 电厂辅机设备BPC :Blade Pitch Control: 叶片节距控制BT :Boiler Tube: 炉管CH: Crusher House: 碎煤房COMB ::Combustion 燃烧COMP ::Compressed Air: 压缩空气CONV ::Conveyer: 输送机CPL :Control Pannel Local: 就地控制盘CPM :Control Pannel Main: 主控盘CRT :Cathode Ray Tube: 阴极射线管: CT Current Transformer: 变流器CYCL :Cyclone: 旋风分离器CAS :Casing:: 缸、壳CB Circuit Breaker: 断路器COMP :Complete: 完成CCCW :Closed Circulating Cooling Water:闭式循环冷却水CCW :Cycle CoolingWater: 循环水CCWHF ::Closed Cooling Water Heater闭式冷却水冷却器CCWP :ClosedCooling WaterPump: 闭式冷却水泵CS :Closed Cooling Water System 闭式冷却水系统CH Coal Handling 煤的装卸CHK VLV :Check Valve: 逆止阀CIRC: Circulation: 循环CLR Cooler: 冷却器CLOW :Cooling Water: 冷却水CMPR :Compressor: 压缩机CNTL :Control: 控制CNTLE :Controller:: 控制器COND :Condensate: 凝结水CONDTY :Conductivity: 导电率CP: Condensate Pump: 凝结泵CIR: Circuit: 回路COUPI :Coupling: 联轴器CP: Condensate Polisher: 除盐装置CS: Control Switch 控制开关CRSV :Cold Reheat Safety Valve: 再热器冷段安全阀CV: Control Valve : 控制阀CWP: Circulation Water Pump: 循环水泵DMPR: Damper : 挡板DP Difference Pressure: 差压DPIC: Differential Pressure Indicating Controller压差指示控制器DPT: Differential Pressure Transmitter 压差变送器DRN: Drain: 疏水DV Drain Valve:: 疏水阀DC Direct Current: 直流电DSH: Desuperheater: 减温器DCA: Drain Cooler Approach: 疏水冷却器通道DEAER Deaerator: 除氧器DEV: Deviation: 偏差DIFFRLY: Differential Relay: 差动继电器DISCH VLV :Discharge Valve 排放阀DIST: Disturbance:: 故障、扰动DSCH: Discharge: 排出ECON: Economizer:: 省煤器EP Electrical Static Precipitator: 静电除尘器ECC Eccentricity :: 偏心EFF Efficiency: 效率EHC Electric Hydraulic Control: 电液控制EO Electric Operate: 电气操作EQ Equipment: 设备ER Error: 误差ES :Extraction System 抽气系统ESC Escape: 逃逸、超出ESS Engineering Safety System: 保安系统EU Engineering Unit : 工程单位EXH Exhaust: 排汽EXT Extract: 抽出FA :Fine Ash: 细灰FDR Feeder: 给料机FE :Flow Element:: 流量元件FI :Flow Indicator:: 流量指示件FDBK: Feedback: 反馈FITG Fitting: 连接件FLW Flow 流量FO :Fail Open: 故障时自动打开FT: Flow Totalizer: 流量累加器FT :Flow transmitter: 流量变送器FV :Flow Control Valve 流量控制阀FY :Flow Relay or Valve 流量传送器FA: Failure Alarm: 故障报警FD :Forced Draft : 强制通风FDF Forced Draft Fan: 送风机FIC :Flow Indicate Controller: 流量指示控制器FLT :Flash Tank : 扩容箱FLD :Field 磁场FLG :Flange: 法兰FLM Flame: 火焰FWH Feed Water Heater 给水加热器FO :Fuel Oil: 燃油FREQ Frequency: 频率FURN Furnace: 炉膛GLD Gland: 密封GRDR Grinder: 碎渣机GND Grounding: 接地GC :Generator Cooling: 发电机冷却GESE Gland Steam Condenser Exhauster:轴加风机GMT Generator MainTrandformer: 发电机变压器GRADGrandient: 梯度GS :Gland Steam: 轴封蒸汽GSC :Gland Steam Condenser: 轴封加热器GV :Governor Valve: 高压调门H ::Heat Conservation 保温HS: Hand Switch:: 手动开关HTR Heater: 加热器HV: Hand Control Valve: 手动控制器HY: Hand Relay or Transducer 手动继电器（转换器）H :Hand: 手动的HB :Heat Balance: 热平衡HD :Heater Drain:: 加热器疏水HDR :Header: 联箱HL ::Heat Loss: 热损失HMDY Humidity: 湿度HPH: High Pressure Heater: 高压加热器HPR :Hooper: 漏斗HPT :High Pressure Turbine: 高压汽机HR: Hot Reheat: 再热器热段HR: Heat Rate: 热耗率HSV: Hot Reheat Safety Valve: 再热器热段安全阀HV AC :Heating Ventilation & Air Conditioning:: 暖通HW :Hotwell: 热井HV ::Hand Control Valve: 手动控制器HYD :Hydraulic: 液力的INTLK :Interlock : 联锁IC :Instrument and Control:: 仪表与控制（热工）ICV ::Inrtermediate ControlValve 中压控制阀ID :Induced Draft 抽风，引风IDF ::Induced Draft Fan: 引风机IGN ::Ignition: 点火装置INLT :Inlet: 入口IPR ::Initial Pressure: 初压INST :Instrument: 仪表INVR :Inverter: 逆变器I /O:: Input/Output 输入/ 输出IP :Intermediate Pressure: 中压ISV ::Intermediate Pressure Turbine SteamValve: 中压缸进汽阀JP :Jet Pump: 喷射器LG :Level Gauge 液位计LVL ::Level: 水位，液位LA :Level Alarm: 液位报警LIM(LMIR): Limiter: 限制器LKG:: Leakage:: 泄漏LP :Low Pressure 低压L.P :Low Point : 低位LPH: Low Pressure Heater: 低压加热器LSH: Local Switch Hand: 就地开关LUB: Lubricating Oil: 润滑油M :Mechanical: 机械M :Motor: 马达MAG:: Magnetic: : 磁性MOD ::Mode: 方式:M/A :Manual/Automatic: 手动/ 自动MAN ::Manual :: 手动MARG: Margin:: 裕量MAX ::Maximum: 最大的，最大值的MCR ::Maximum Continuous Rating 最大连续出力MCV:: Main Control Valve: 主控制阀MD :Modulation Damper: 调节挡板MDBFP: Motor Driven Boiler Feedwater Pump: 电动给水泵MEAS ::Measure : 测量MFT: Master Fuel Trip: 主燃料跳闸MIN :Minimum: 最小的MKUP (MU) Make-up: 补充ML :Mill: 磨煤机MN :Main: 主要的M.O. :Manual Operation: 手操MPT :Main Power Transformer: 主变压器MS :Main Steam 主蒸汽MSV :Main Steam Valve: 主汽阀NOZ: Nozzle: 喷嘴NPSH :Net Pump Suction Head: 泵的静吸压头OL: Overload: 过载OLR :Overload Relay: 过载继电器OPER :Operation: 运行OSC :Oscillograph: 示波器OTLT: Outlet: 出口PA: Primary Air: 一次风PAF :Primary Air Fan: 一次风机PAH :Pressure Alarm High: 高压报警PAL :Pressure Alarm Low: 低压报警PB: Push Button 按钮PC :Power Centre: 动力中心PC: Pressure Controller: 压力控制器P.C. :Pressure Control: 压力控制PCP :Precipitator 除尘器PCV :Pressure Control Valve:: 压力控制阀PDI :Pressure Differential Indication: 差压指示PDT :Pressure Differential Trandsmitter: 差压变送器PED :Pdestal:: 轴承座PERF CALC Performance Calculation:: 性能计算PF: Power Factor 功率因数PHTR: Preheater: 预热器PMP :Pump: 泵PNEU :Pneumatic: 气动的PR: Pressure Recorder: 压力记录计PRG :Purge: 吹扫PRV :Pressure Relief Valve: 泄压阀PRO :Protection: 保护PROGR:: Program: 程序PT: Pressure Transmitter: 压力变送器PULV: Pulverizer: 磨煤机PVSV :Pressure Vacuum Safety Valve 压力真空安全阀PW: Plant Water 厂用水PY: Pressure Relay: 压力继电器QA: Quality:: 质量，性能RB: Run Back: 快速降负荷RCV :Recovering: 回收RECIRC:: Recirculation 再循环RECT :Rectifier: 整流器RET :Return: 返回RH: Reheater: 再热器RO: Restriction Orifice: 节流孔板ROT :Rotor: 转子RTU :Remote Telemetry Unit:: 遥测装置SA :Secondary Air: 二次风SAT: Saturate: 饱和的SC :Steam Coil Air Heater:: 暖风器SCA V :Scavenge: 吹扫SD: Shut-off Damper: 关断挡板:Shut-Down 停机SEP :Separator 分离器SG: Switchgear 开关装置SH: Superheater: 过热器SLS :Seals:: 密封SO: Shut Off: 关闭SPD :Speed: 转速SPRA: Spray: 喷水SPT :Support: 支持: ST: Start: 启动，开始STD-BY :Stand By: 备用ST: System:: 系统STM :Steam: 蒸汽STR: Stator:: 定子STRNR: Strainer: 滤器SU: Start Up: 启动SV: Solenoid Valve: 电磁阀SUCT: Suction: 吸入SW: Switch: 开关:Steam Water: 汽水SBLWR: Soot Blower 吹灰器TBFP Turbine Drive Boiler FeedwaterPump 汽泵TCV :Temperature ControlValve 温度控制T.B.: Transfer Damper: 转换挡板TE: Temperature Element: 温度元件TG: Turbine-generator: 汽轮发电机Turbine-gear: Turbine-gear: 汽机盘车THERM :Thermal 热力的TMS: Turbine Master System: 汽机主控系统TRANS :Transfer: 转换TRBL: Trouble: 故障TRKG: Tracking: 跟踪TT: Temperature Transmitter: 温度变送器TTD: Terminal Temperature Difference:温度端差TW: Thermowell: 热电偶套管UAM :Unit Automatic Master: 机组自动系统V AC: Vacuum: 真空V AL: Value: 数值VB: Vibration 振动VLV: Valve: 阀门WH: Watthour 瓦小时WP: Working Point: 工作点WW: Water Wall 水冷壁WX: Watt Transducer: 功率转换器COVER :Crossover 切换管CV: Control Valve: 控制阀英汉对照表A/H ：AUTOMATION/HAND : 自动/ 手动; A/M ：AUTOMATION/MANUAL: 自动/ 手动;ALARM 报警;AUX ：AUXILIARY :: 辅助;BYPASS 旁路CLOSE 关（状态，常指阀门）;CODE: 代码；编码COLD START — UP: 冷态启动COMPUTER : 计算机CURVE ，LINE: 曲线，线DATA: 数据；文件；资料DECREAS : 减少DESK: 台，桌DIGIT: 数字DISK: 磁盘DYNAMIC ；DYNAMICAL: 动态F ：FLOW 流量;FAST: 快FIGURE: 图示HIGH: 高HOT START — UP: 热态启动I＆C ：INSTRUMENT AND CONTROL仪表与控制INCREAS: 增加INDICATION ；DISPLAY : 指示；显示;INLET 入口;INPUT 输入;INTERMEDIATE 中KEYBOARD: 键盘KW ：KILOWATT 千瓦L ：LOAD 负荷，负载;LOC ：LOCAL : 就地LOW: 低MCS ：MANAGMENT COMMAND SYSTEM 管理命令系统MODE : 方式，模式MW ：MEGAWATT 兆瓦NORMAL: 正常OFF : 关（状态）;ON : 开（状态）;OPEN: 开( 状态，常指阀门);OPERATE : 运行；操作;OUTLET 出口;OUTPUT 输出;P ：PRESSURE: 压力;PANEL 盘PARAMETER : 参数PIPE ；TUBE: 管道，管子PLANT: 厂，站POWER: 功率，电源;PRINT: 打印R ：RATE : 比率，速率;R ：RESISTANCE: 电阻;REM ：REMOTE : 摇控;RESET 复位ROOM : 室RPM:: 转/ 分;S ：SPEED 速度;SELECT 选择SET POINT 设定点SHUTDOWN : 停机;SIDE （某）侧，边;SILENCER 消音器SLOW : 慢STAND BY: 备用;START : 启动;STARTUP : 起动；启动;STATIC 静态STATION 站STOP: 停止;SYMBOL 符号SYSTEM: 系统T ：TEMPERATURE:: 温度; TEST: 试验;TRANSMITTIER;TRANSDUCER: 变送器；传感器TRIP 跳闸; TRIP ACKNOW: 跳闸确认UNA V AIL 不允许( 不能投用的)UNIT : 单元、机组V ALVE 阀门W ARM START — UP: 温态启动ZOOM: 摄像机镜头锅炉部分ACTUAL MEGAWATT: 有功AIR DRAFT SEQUENCE: : 风机程序控制（顺控）AIR HEATER A MOTER: 空预器马达AAIR HEATER LOC/REM SELECT: 空预器就地/ 遥控选择AIR HEATER MOTOR LEAD: 空预器马达选择AIR HTR A SEC AIR OUT TEM 空预器A 二次风出口温度AIR PREHEATER: 空预器AIR SVCE SUPPLY: 服务空气ALARM LIMITS: :: 报警限制ALL AIR HTRS RUNNING 各空预器运行ALL PULV GRP SHUTDOWN 所有磨组停运ASH — HOPPER: : 灰斗ATTEMPERATOR: : 减温器AUX .ST: SPLY FOR ATOMIZ 辅助蒸汽供雾化蒸汽BOIL MILL A BNR MET TEMP 炉A 磨组喷燃器金属温度BOIL MILL A GR1 WDBOX PR 炉A 磨组第一组风箱压力BOILER AIR REQUIRED 锅炉风量需求（>30% ）BOILER EFFLUENT STORAGE: POOL 锅炉废水池BOILER FOLLOW MODE: 炉跟随方式BOILER MASTER: 锅炉主控器BOILER TRIP RESET: : 锅炉跳闸复位BOILER: 锅炉BURNNER: : 燃烧器CHIMNEY ；STACK:: : 烟囱CLEAN: 清扫COAL BANKER: :: 煤仓COAL FEEDER : 给煤机COMBUSTION : 燃烧CONVEYOR: 皮带机COORDINATE MODE 协调方式CRUSHER: 破碎机DECR/INCR PRESS AT FIX LOAD:: 固定负荷方式增减压力DOWM COMER:: 下降管DRAIN & VENT: 疏水和排气ECONOMIZER : 省煤器EITHER FAN RUNNING : 任一风机运行EITHER ID FAN RUNNING 任一吸风机运行ELECTROSTATIC PRECIPITATOR : 静电除尘器FD FAN A FLOW:: A 送风机流量FD FAN/ID FAN A CONT DAMPER A 送/ 吸风机控制挡板FEED W ATER FLOW: 给水流量FEEDER LOCAL SELECT: 给煤机就地控制选择FEEDER REMOTE SELECT: 给煤机遥控选择FLUE GAS: 烟气FORCED DRAFT FAN : 送风机FUEL GAS ID FAN A OUTLET PRESS A 吸风机出口压力FURNACE PRESS: 炉膛压力FURNACE: 炉膛GAS COAL: :: 烟煤HEADER : 联箱、母管IGNITOR: : 点火器，油枪INDUCED DRAFT FAN : 引风机INDUCED&FORCED DRAFTS: 吸送风机INITIATE: 启动、引燃、激发、触发ISOLATION: 隔离；绝缘LFO .DISCH .PRESS : 轻油出口压力LIGHT OIL SEL GRP 1: 第一组轻油枪选择LIGHT OIL: 轻油LUB OIL PUMP:: 润滑油泵MAIN STEAM STOP VLV: 主蒸汽截止阀MAIN STEAMTEMP/PRESSURE/FLOW 主汽温度/压力/ 流量MAINTAINED IGNITORSPULVERIZER A:磨煤机A油枪操作MANUAL LOAD SET/RATE:手动负荷设定/ 负荷率MANUAL MODE: 手动方式MANUAL THROTTEL PRESS SETPOINT:手动节流压力设定值MILL A GROUP MASTER : A 磨组主控器MILL A LOAD: A 磨组负荷MILL A OUT TEMP CONT DAMPER : A 磨组出口温度控制挡板MIN MAX LOAD （LIMITS ）: 最大最小负荷（限制）MMMC ＝MILLIMETER MERCURY ；MMH2O: 毫米汞柱；毫米水柱O 2 IN THE FUEL GAS 烟气含氧量OPEN/CLOSE SWING VLVS 摆阀开/ 关OPERATE MODE SELECT: 运行方式选择PENDANT: : 悬吊管PLATEN SPARY CONTROL VLVS SIDEA : 屏过减温水A 侧控制阀PLATEN SUPERHEATER: 屏过PRESSURE DIFFERENCE: 压差PRI AIR DUCT PRESS 一次风管压力PRI AIR FAN A CONT DAMPER: A 侧一次风机控制挡板PRI AIR FAN A OUTLET PRESS A 一次风机出口压力PRI AIR FLOW MILL A CONTDAMPER 磨组一次风控制挡板PRI/SEC AIR FLOW MILL A A 磨组一次/ 二次风流量PRIMARY AIR FAN: 一次风机PRIMARY AIR SEQUENCE: 一次风控制PULVERIZER : 磨煤机PULVERIZER EMERGENCE TRIP 磨煤机紧急跳闸PULVERIZER INERT MODE SELECT:磨煤机惰性方式选择PULVERIZER NORMAL MODESELECT: 磨煤机正常方式选择PULVERIZER SELECTION A :: 磨煤机A 选择PULVERIZER: M/A: SELECT 磨煤机手/ 自动选择PURGE 吹扫RH ；REHEATER: 再热器SAFETY V ALVE:: 安全阀SCANNER BLOWERS: 火检吹扫器SEAL AIR FAN PRESS: 密封风机压力SEAL AIR FAN:: : 密封风机SEC AIR DUCT PRESS: 二次风管压力SEC AIR FLOW MILL A CONT DAMPER A 磨组二次风流量控制挡板SEC SH OUT STEAM TEM 二级过热器出口蒸汽温度SEC SH SPARY CONT VLVS SIDE A二级过热器减温水A 侧控制阀SECONDARY SH INLET TEMP 二级过热器进口温度SECONDARY: AIR 二次风SH ；SUPERHEATER: : 过热器SH STEAM ELECTR VLV: 过热器电磁阀SH STEAM TEMP SET POINT:: 过热温度设定点SH/RH SPARY W ATER STOP VLVS:: 过热器/ 再热器减温水截止阀SH/RH SPRAY CONTROL VLVSSELECT 过热器/ 再热器减温水控制阀选择SLIDING PRESS MODE: 滑压运行方式SOOT BLOWER: 吹灰器SPARK 火花，点火花SPEED CHANGE (NOT) PERMISSIVE:速度切换（不）允许SPRAY : 喷水STACKER RECLAIMER :: 堆取料机START IGNITOR GRP 1: 第一组油枪点火STEAM DRUM: : 汽包STEAM 蒸汽STONE COAL: 无烟煤STOP IGNITORS GRP 1: 第一组油枪停止STOP/START FEEDER 给煤机停止/ 启动STOP/START IGNITORS: 油枪停止/ 启动STOP/START MILL: 磨组停止/ 启动STOP/START PA FLOW: 一次风停止/ 启动STOP/START PULVERIZER 磨煤机停止/ 启动STOP/START SEQUENCEPULVERIZER A: 磨煤机 A 程序停止/ 启动THROTTLE PRESS:: 节流压力TRANSPORT AIR SEQUENCE 风量程序控制（顺控）TURB FIRST STAGE PRESS 汽机第一级( 调节级) 压力TURBINE FOLLOW MODE: 机跟随方式TURBINE MASTER: 汽机主控器TWIN FLOW AIR HTR A CONT VLV: :双流式空预器控制阀UNLOADER: :: 卸煤机WATER 水WATERW ALL: : 水冷壁汽机部分:EMERG OIL PUMP: 事故油泵<P>CICR PMP DISCHARGE VLV: 循环泵出口阀1ST STAGE PRESS: 第一级压力ACTUAL MEGA WATT: : 实际负荷数AMS ：ADMISSION: MODESELECTION 进汽方式选择AUX STEAM HEADER: : 辅汽联箱AUX STEAM TEMP CONTROL: 辅汽温度控制AUX STM HEADER PRESS CONTROL VLV 辅汽联箱压力控制阀BALANCE: : 平衡BEARING BRASS:: 轴瓦BEARING: : 轴承BLADE 叶片BOILER FOLLOW MODE: 锅炉跟随方式BOOSTER FEED PUMP: 前置给水泵CICR WTR PUMP: 循环泵CIRCULATING PUMP: : 循环泵CIRCULATING: 循环CLOSED COOLING W ATER: 闭式冷却水CLOSED COOLING WTR PUMP: 闭式冷却水泵CMPTR: : 计数器CONDENSATE PUMP: 凝泵CONDENSER AIR SUCTION VLV: 凝汽器抽空气阀CONDENSER HOT WELL: : 热井CONDENSER LEVEL CONTROL VLV:凝汽器水位控制阀CONDENSER: 凝汽器CONDS EXTR PUMP DISCH : 凝结水抽吸泵出口CONDS STOR TANK LEVEL: 凝结水储水箱水位COOLER: : 冷却器COOLNG WTR PUMP: 水冷泵COORDINATE MODE: : 协调方式CV ：CONTROL V ALVE 高压调门CYLINDER 、CASING: 汽缸DEAERATOR LEVEL CONTROL VLV:除氧器水位控制阀DEAERATOR: : 除氧器DECR PRESS AT FIX LOAD: 在负荷不变下减压DEMI WATER: 除盐水DISPATCH PARTICIPATION 调度（参与）指令DURM PRESSURE:: 汽包压力EJECTOR: 喷射器，抽气器EMERGENCY GOVERNOR 危急保安器EXHAUST: 排汽EXPANSION: 膨胀EXTR ST TO HP HTR 抽汽至高加EXTRACTION STEAM 抽汽FILTER: : 滤网FLANGE 法兰FUNCTION GROUP: 功能组FW CONTROL V ALVE ' S BYPASS VLV:给水控制阀的旁路阀FW FLOW 30% CONTROL VLV : 30%给水控制阀FW FLOW MASTER CONTROL: 给水流量主控FW HP HTR DISCH TEMP: 给水高加出口温度FW PUMP RECIRCUL CONTROL VLV给水泵循环控制阀FW VLV: 给水阀门GEARING: 盘车GOVERNOR: 调速器HP ATTEM PRESS CONTROL VLV: 高旁减温水压力控制阀HP ATTEMP BLOCK VLV: 高旁减温水闭锁阀HP BYPASS ＆HP ATTEMP VLVS:高压旁路及减温水阀HP BYPASS PRESS CONTROL VLV 高旁压力控制阀HP BYPASS PRESS SET POINT: 高旁压力设定值HP BYPASS TEMP CONTROL V ALVE 高旁温度控制阀HP＆LP BYPASS COMMAND 高压及低压旁路指令HPH ：HIGH PRESSURE HEATER : 高加HYDRAULIC OIL STATION PUMP: 液压油站泵INCR PRESS AT FIX LOAD: 在负荷不变下增压INT POS: 中间状态IV ：INTERMEDIATE V ALVE 中压联合汽门JACKING OIL PUMP 顶轴油泵LP HTR STOP VLV 低加截止阀LP ＆HP BYPASS PRESS SIDE A 低压或高压旁路A侧压力LP ＆HP BYPASS TEMP SIDE A 低压或高压旁路A侧温度LPH ：LOW PRESSURE HEATER:低加LUBE OIL PUMP: 润滑油泵MAKE －UP W ATER: 补给水MANUAL LOAD RATE 手动负荷率MANUAL LOAD SET 手动负荷设定MANUAL Throttle Press Set Point手动节流压力设定值MEASURE SELECTION 测量选择站MOP ：MAIN OIL PUMP: 主油泵MOTOR DRIVEN FEED WATER PUMP电动给水泵MSV ：MAIN STOP V ALVE: 主汽阀NOZZLE 喷嘴OIL PURIFIER: 净油器OIL STORAGE TANK : 储油箱OPERATE MANUAL MODE: 手动方式OPERATE MODE SELECT: 运行方式选择PILOT V ALVE: 错油门PLATEN SH INLET TEMP SIDE A: A侧屏过入口温度PRIMARY SH STOP V ALVE: 一级过热器截止阀PUMP A DISCH PRESS : A 泵出口压力RH SPRAY BLOCK VLVSTRIP INIT 再热器喷水闭锁阀跳闸启动RH SPRAY WTR STOP VLVS: 再热器喷水截止阀RH STEAM ATTEM FLOW: 再热喷水流量RH STEAM TEMP OUTLET: 再热器出口温度ROTOR 转子SEAL: 密封SHAFT 轴SILENCER: 消音器SLIDING PRESS MODE: 滑压方式SPEED INDICATOR OR SPEEDMETER: : 转速表STATOR 定子STEAM TURBINE : 汽轮机ST －UP BOIL FDW PUMP: 启动给水泵SUCTION PUMP: 抽吸泵SURGE APPROACH: 喘振SYNCHRONIZER: 同步器TFW PMP DISCHARGE VLV: 汽动泵出口阀TFW PUMP MAIN OIL PMP: 汽动给水泵的主油泵THROTTLE ORIFICE 节流孔板TURBINE DRIVEN FEED WATERPUMP: 汽动给水泵TURBINE FW PUMP AUX ＆VLV 小机给水泵辅汽及阀门TURBINE GENERATOR: 汽轮发电机组TURBINE INLET PRESS: 汽机入口压力TURBINE MASTER : 汽机主控器TURBING FOLLOW MODE: 汽机跟随方式V ACCUM 真空V ACUUM BROKEN V ALVE: 真空破坏门V ACUUM SEQ : 真空程控VIBRATION: 振动电液调节及控制部分1STAGE PRESSURE FEEDBACK: 第一级压力反馈ABNORMAL CONDITION: 异常状态ACCELERATION: 加速度ACTIVE POWER:: 有功功率ADMISSION MODE: 进汽方式ADS(ALARM DISPLAY SELECTPANELS) 报警显示选择屏AERIAL LINE: 架空线ALTERNATING CURRENT (AC): 交流AMPERE: 安培ANGLE OF LAG: 滞后角ANGLE OF LEAD: 超前角ANODE: 阳极ARC: 电弧ARMATURE 电枢AST ：AUTO SHUT-DOWN TRIP: 自动停机遮断ASYNCHRONOUS MOTOR: 异步电动机AT SET SPEED: 在设定速度位置ATC ：AUTO TURBINE CONTROL:自动汽轮机控制AUTOFORMER: 自藕变AUTORECLOSING : 自动重合闸AUXI TRANSFORMER : 厂用变BACK UP TRANSFORMER 备用变BACK-UP OVERSPEED TRIP TEST 备用超速跳闸试验ELECTRICAL TRIPTEST 电气跳闸试验BACK-UP SPDSIG LOST: : 后备速度信号失去BARRING OIL PUMP 盘车油泵BASE LOAD: 基荷BATTERY : 电池BATTERY BACKED CLOCK 电池备用时钟BDV ：BLOWDOWN VLV: 泄放阀BOOSTER PUMP: 前置泵BULB : : 灯泡BUS SECTION : 母线分段BUS: 母线BUSBAR FRAME: 母线架BUSCOUPLER: 母联BUSHING 套管CABLE 电缆CAPACITANCE: 电容CARRIER 载波CATHODE : 阴极CCR: 中控室CHARGING EQUIPMENT : 充电设备CHEST /ROTOR WARMING: 腔室/转子预暖CIU : 计算机接口单元CLOSE : 合闸CLOSED V ALVES OVERSPEED TEST关闭阀超速CLOSED-LOOP : 闭环COIL:: 线圈COMBINED RECLOSING 综合重合闸COMBINED REHEAT V ALVES: 中压联合阀COMMON SERVICES LOGIC SUITE::公用系统逻辑柜COMMUNICATION: 通讯CONDUCTOR : 导体CONFIGURATION: 结构，布置，外形:CONTROL OIL: 控制油CORE: 铁芯CPU(CENTARL PROCESSING UNIT: 中心处理单元CRT: 显示屏CURRENT TRANSFORMER: 电流互感器CURRENT 电流CV:: 控制阀DAS: 数据采集系统DECREASING LOAD RATE: : 减负荷率DIESEL GENERATOR : 柴油发电机DIRECT CURRENT (DC) 直流DISCONNECTOR : 隔离开关DISTRIBUTED CONTROL SYSTEM:分散控制系统E.W.S.: 工程师工作站EHC STATUS: 电液调节系统状态EHC ：ELECTRO-HYDRA CONTROLSYSTEM: 电液调节控制系统EHV MIMIC PANEL : 电气高压模拟屏ELECTRICAL MALFUNCTIONSYSTEM FAULT : 电气失灵系统故障EMERGENCY OIL PUMP: 事故油泵EMERGENCY SEAL OIL PUMP: 事故密封油泵ETS ：EMERGENCY TRIP SYSTEM:危急跳闸系统EXCEPTION REPORT: 例外报告EXCITE 励磁EXCITOR 励磁机FA/PA POSITION : 全周/ 部分（进汽）位置FAST-ACTING SOLENOID: 快动电磁阀FIRST STAGE PRESS 调节级压力FIS :: 流量显示开关FREQUENCY: 频率FRF ：FIRE RESISTANT FLUID:: 抗燃油FULL ARC : 全周进汽GAS : 瓦斯GEN. SHAFT SEAL&STATOR WIND : 发电机密封及静子绕组GENERATOR : 发电机GROUNDING(EARTHING) 接地H2 TEMP CONT V : 氢气温度控制阀HARDW ARE 硬件HOLD: 保持HYDRAULIC FLUID PRESS: 抗燃油压力I.C.S: 数字控制站终端模件IN STANDBY: 在备用状态IND: :: 指示器INDUCTANCE: 电感INHIBITED: 停止进行、禁止INSULATOR 绝缘子INTERCEPT V ALVE: 中间截流阀INTERCEPT V ALVES: 中间截止阀INTERFACE 接口KILOW ATT 千瓦LC: 液位控制器LI: 液位显示LIGHT: 照明LINE 线路LK: 液位控制站LOAD DECREASING ；AT SETLOAD 负荷减；在设定负荷LOAD FLOW : 负荷潮流分布LOAD INCREASING: 负荷增LOAD LIMITING SET: 负荷极限设定LOAD MONITORING: 负荷监视LOAD SELECT: :: 负荷选择LOAD SET: 负荷设定LOAD: 负荷LOADING RATE LIMIT : 负荷（增、减）率限定LOCKED OUT: 闭锁LOSS : 损耗LOSS OF PWR:: 失去电源LVDT ：线性位移差动变送器MAGNETIC FIELD: 磁场MAIN OIL PUMP: 主油泵MAIN SEAL OIL PMP : 主密封油泵MAIN STEAM PRESS 主蒸汽压力MAIN TRANSFORMER STEP-UP TRANSFORMER: 主变MANUAL: 手动MCC: 马达控制中心MEGAWATT: 兆瓦MFP : 多功能控制器MOTOR: 电动机MSPL ：MAIN STEAM PRESSURELIMITER : 主汽压力限制器MSV: 主蒸汽阀NEUTRAL POINT: 中性点OHM: 欧姆OIL GAUGE: 油位表OPC ：OVERSPEED PROTECTIONCONTROL: 超速保护控制OPEN-LOOP : 开环OPER AUTO: 操作员自动::OPERATING MODE : 操作方式ORP ：OIL RESET PISTON: 油复位活塞ORSV ：OIL RESET SOLENOID VLV油复位电磁阀OTSV ：OIL TRIP SOLENOID VLV: 油跳闸电磁阀OVER CURRENT: 过流OVER VOLTAGE : 过压OVERLOAD: 过载PART ARC : 部分进汽PC: 动力中心PDIS : 压差显示开关PEAK LOAD: 峰荷PERMANENT MAGNETICGENERATORDF 永磁发电机PG: 压力计PHASE ANGLE : 相角PHASE: 相PIC: 压力显示控制器PK: 压力控制站PLUG : 插头PLUG SOCKET: 插座POLE:: 电极POTENTIAL TRANSFORMER 电压互感器POWER 功率POWER FACTOR: 功率因数POWER LOAD UNBALANCE: 功载不平衡PP ：: PREESSURE POINT 压力检测点PRI SPD SIG LOST 一次速度信号失去PS: 压力开关PT: 压力变送器REACTANCE: 电抗REACTIVE POWER: 无功功率RECLOSING : 重合闸REHEAT PRESS:: 再热汽压力REMOTE AUTO: 远方自动REMOTE OPERATION : 远操RESISTANCE: 电阻RSM ：ROTOR STRESSMONITORING: 转子热应力监视:RSV: 再热汽截止阀SAFELY OIL : 安全油SCR CONTROLLER: 可控硅整流控制器SEAL OIL: 密封油SHUT-OFF V ALVE:: 切断阀SIGNAL: 信号SLOW MEDIUM FAST: 慢、中、快SPEED INCREASING: 速度增SPEED MONITORING: 速度监视SPEED SET RPM : 转速设定转/ 分SPEED: 速度，转速START UP TRANSFORMER 启动变STATOR WIND COOLING W ATER PUMP: 定子绕组冷却水泵STEAM SEAL BY-PASS UNLOAD VLV: 蒸汽密封旁路泄放阀STEAM SEAL DIVERING V ALV: 密封汽分流阀STEAM SEAL SYS:: 蒸汽密封系统SUCTION PMP A/M SEL: 抽吸泵手/ 自动选择SUCTION PUMP: 抽吸泵SUPERVISORS DESK: 值长台SWITCH 开关SWITCHGEAR : : 配电盘、开关装置TELEPHONE: 电话TEST SELECT: 试验选择（联锁）THERMO-COUPLE: : 热电偶THREE ELEMENTS LEVELCONTROLLER: 三冲量水位控制器THRUST BEARING WEAR DETECTORTEST 推力轴承磨擦检测试验TI : 温度显示器TIC :: 温度指示控制TIME DELAY: 时间延迟TP: 温度检测点TRANSFER AND FILTER PUMP: 输送和过滤油TRANSFORMER: 变压器TRANSMISSION: 传输TRIP 跳闸TS: 温度开关TSI: 汽机监视仪表TT:: 温度变送器TURB LUBE OIL TEMP CONTROL V :汽机润滑油温度控制阀TURBIN DRAIN V ALVES: 汽机疏水阀TURBINE LATCHED: 汽机挂闸TURN GEAR CONTROL SEQUENCE盘车控制程序TURN GEAR MOTOR: 盘车主电机TURN GEAR PIGGY: BACK MOTOR盘车啮合电机UNINTERRUPTED POWER SUPPLY:不间断电源UNIT CONTROL DESK: 机组控制台UNIT TRANSFORMER:: 单元变V ACUUM TRIP: 真空跳闸V ALVE POSITION: 阀位置VI : 阀位置指示VOLT(V): 伏特VOLTAGE 电压VT: 阀位置变送器VV ：VENTILATING V ALVE : 通风阀W ARMING RATE: 暖机速率WATT: 瓦特WINDING: 绕组。
火电厂英语专业词汇(电气)
double-flow
双向流动
side wall
侧墙
dowel
销钉
signal conditioning
信号调节
drain pipe
疏水管
silicon
硅
Drain
疏水
single-flow
单向流动
dry
干燥基
slave module
子模块
dry and ash free
可燃基
Slipping
滑环
电动机启动装置
axial
轴向的
motor-operated
电动操纵的
back-up
备用
moving blades/ blading
动叶片
bar
条形
multifork root
叉型叶根
bargraph
条形图
Multi Function Process(MFP)
多功能处理器
batch
成组的、成批的
MVA: mega volt-ampere
rotor
转子
density
密度
RTD
热电阻
diaphragm
隔板
stator
定子
dielectric
不导电的、绝缘的
saturated water
饱和水
digit display
数字显示
scheme: system
系统
digit signal
数字信号
screw
螺钉
dimension
尺寸
search coil
火电厂英语专业词汇（电气）
acid cleaning
火力发电厂常用英语词汇
火力发电站常用英语技术词汇induced draught fan: 引风机electrostatic dust remover(precipitator):静电除尘器pulverizer 磨煤机chimney: 烟囱boiler house:锅炉房deaerator: 除氧器slag pump 灰渣泵coal conveyor 输煤装臵feed water tank: 供水箱thermal cycle: 热力循环coal bunker: 煤仓boiler feed pump: 给水泵(net)heat rate: （净）热耗率coal mill 磨煤机switchgear: 开关设备Assemblie: 集合，集结，组装steam boiler, water boiler tube 蒸汽锅cable tunnel: 电缆通道comment 注释，评论炉，管式锅炉furnace(combustioncable cellar: 电缆槽module : 模块standby: 备用chamber): 炉膛( 燃烧室) turbine room: 汽轮机室proximity 相近，接近，亲近water tube: 水管steam turbine with alternator: 蒸汽汽detector: 探测器bracket: 支架轮发电机组economizer:省煤器ash pit 灰坑interlocks 互锁，联锁axial: 轴向的superheater: 过热器steam drum: 汽包surge conditions: 喘振:water preheater: 水预热器surface condenser:表面凝汽accessory: 附件pulsation: 有节奏的跳air preheater: 空气预热器low-pressure preheater:低压预热器动，跳动gas duct(flue): 烟气管, 烟道circulating water pipe(pump): 循环水fossil fired: 燃煤intent: 意图，目的，dust collecting plant: 集尘室管意向electrical precipitation plant: 电气除尘室control room: 控制室intend: 意指，想要，打算consistent: 一致的，调和的sludge :: 污泥，淤泥foreign matter: 不Intercept: 截止相关的物质facilitate: 推动，促进，使简practice: 惯例，实习，实践Fetting: 附件intrinsic: 固有的，内在的Gage:: 规，表，压力计化procurement 获得，获取multistage: 多级的Taps: 接头fabrication: 制作，构成，伪造物remote control: 遥控test wells: 测点插孔vent: 通风孔，出烟孔，出口，放出，排safety relief valve: 安全卸压阀stress-relieved: 应力消除出，noncondensible gas:不凝结气体gauge: 量规，量表，测量thermometer: 恒温计intermittent 间歇的，断断续续的manhole: 人孔，检修孔steam purge system:蒸汽吹扫系统blowdown : 排污tank: 桶，箱，罐equivalent: 等价物，相等的centrifugal type pumps: 离心式泵diagram: 图表deaerator: 除氧器forging:: 锻造seat: 部位，座friction losses: 磨擦损失corrosion : 侵蚀，腐蚀状态socket welding: 管座焊接solenoid: 螺线管concentration 集中，集合，浓缩，浓度enthalpy: 焓modulat: 调整，调节recommend 推荐，介绍，托付，劝告estimate: 评价，评估，估价criteria: 标准abnormal and normal conditions: 变工况parameters 参数，参量wrenches: 扳手和额定工况warm up: 暖机nominal : 名义上的，额定的，标称的pipe taps: 管接头.acid wash: 酸洗MS —Main Steam : 主蒸汽scale: 范围，水垢，水锈，比例，刻度Cycle:: 循环AX THR BRG :Axis Thrust Bearing: 轴Rating: 锅炉最大连续出力BFBP::向推力，轴承ATMZ :Atomizing: 雾化A List of Abbreviations and Symbols in Boiler Feed Booster Pump: 锅炉给水增压泵BNR :Burner: 燃烧器English-Chinese AUTO :Automation 自动AUX :Auxiliary: 辅助的BOP :Balance Of Plant: 电厂辅机设备A ::Ash Handling System: 除灰系统BA :Bottom Ash 底灰BPC :Blade Pitch Control: 叶片节距控制AH :Air Heater: 空气预热器BAH ::Bottom Ash Hopper: 底灰斗BT :Boiler Tube: 炉管AAh :Analyzer, Alarm High : 分析器，高BLR ::Boiler: 锅炉CH: Crusher House: 碎煤房值报警:: AIV :Air Intake V alve: 进气阀BSD ::Boiler Shut Down: 停炉COMB ::Combustion 燃烧ALIGN Alignment: 校正BUSH :Bushing: 衬套COMP ::Compressed Air: 压缩空气ALKF :Airlock Feeder: 锁气器BYPS :Bypass:: 旁路CONV ::Conveyer: 输送机AP ::Ash Slurry Pump: 灰浆泵BVD ::Boiler Vents and Drains:: 锅炉疏CPL :Control Pannel Local: 就地控制盘水放气BFP :Boiler Feedwater Pump ::ATM :Atmosphere 大气CPM :Control Pannel Main: 主控盘锅炉给水泵BFPT:Boiler FeedwaterAC ::Air Conditioner: 空气调节器CRT :Cathode Ray Tube:阴极射线管: AFT :Atmosphere Flash Tank: 大气扩容Pump Turbine: 锅炉给水泵汽机CT Current Transformer: 变流器器AC :Alternating Current: 交流电BFW ::Boiler Feedwater: 锅炉给水CYCL :Cyclone: 旋风分离器ALM :Alarm:: 报警BM :Boiler Master 锅炉主控CAS :Casing:: 缸、壳AMP :Ampere: 安培BMCR:Boiler Maximum Continuous CB Circuit Breaker: 断路器COMP :Complete: 完成CONDTY :Conductivity: 导电率DSH: Desuperheater:减温器CCCW :Closed Circulating Cooling Water: CP: Condensate Pump:凝结泵DCA: Drain Cooler Approach: 疏水冷却闭式循环冷却水CCW :Cycle Cooling 器通道DEAER Deaerator: 除氧器CIR: Circuit: 回路Water: 循环水COUPI :Coupling: 联轴器DEV: Deviation: 偏差CCWHF ::Closed Cooling Water Heater CP: Condensate Polisher:除盐装臵DIFFRL Y: Differential Relay: 差动继电闭式冷却水冷却器CCWP :ClosedCS: Control Switch 控制开关器Cooling WaterPump: 闭式冷却水泵CRSV :Cold Reheat Safety Valve: 再热器DISCH VLV :Discharge Valve 排放阀冷段安全阀CV: Control Valve : 控制阀CS :Closed Cooling Water System闭式冷DIST: Disturbance:: 故障、扰动却水系统CH Coal Handling 煤的装卸CWP: Circulation Water Pump: 循环水泵DSCH: Discharge: 排出CHK VL V :Check Valve: 逆止阀DMPR: Damper : 挡板ECON: Economizer:: 省煤器CIRC: Circulation: 循环DP Difference Pressure:差压EP Electrical Static Precipitator: 静电除CLR Cooler: 冷却器DPIC: Differential Pressure Indicating尘器CLOW :Cooling Water: 冷却水Controller 压差指示控制器DPT: ECC Eccentricity :: 偏心CMPR :Compressor: 压缩机Differential Pressure Transmitter 压差变EFF Efficiency: 效率送器DRN: Drain: 疏水CNTL :Control: 控制EHC Electric Hydraulic Control: 电液控CNTLE :Controller:: 控制器DV Drain V alve:: 疏水阀制COND :Condensate: 凝结水DC Direct Current: 直流电EO Electric Operate: 电气操作EQ Equipment: 设备FT: Flow Totalizer: 流量累加器GRDR Grinder: 碎渣机ER Error: 误差FT :Flow transmitter: 流量变送器GND Grounding: 接地ES :Extraction System 抽气系统FV :Flow Control V alve 流量控制阀GC :Generator Cooling: 发电机冷却ESC Escape:逃逸、超出FY :Flow Relay or V a lve 流量传送器GESE Gland Steam Condenser Exhauster: 轴加风机GMT Generator Main ESS Engineering Safety System: 保安系FA: Failure Alarm: 故障报警统FD :Forced Draft : 强制通风Trandformer: 发电机变压器GRAD EU Engineering Unit : 工程单位FDF Forced Draft Fan: 送风机Grandient: 梯度EXH Exhaust: 排汽FIC :Flow Indicate Controller: 流量指示GS :Gland Steam: 轴封蒸汽控制器FLT :Flash Tank : 扩容箱EXT Extract: 抽出GSC :Gland Steam Condenser: 轴封加热器GV :Governor Valve: 高压调门FA :Fine Ash: 细灰FLD :Field 磁场FDR Feeder: 给料机FLG :Flange: 法兰H ::Heat Conservation 保温FE :Flow Element:: 流量元件FLM Flame: 火焰HS: Hand Switch:: 手动开关FI :Flow Indicator:: 流量指示件FWH Feed Water Heater给水加热器HTR Heater: 加热器FDBK: Feedback: 反馈FO :Fuel Oil: 燃油HV: Hand Control Valve: 手动控制器FITG Fitting: 连接件FREQ Frequency: 频率HY: Hand Relay or Transducer 手动继电器（转换器）H :Hand: 手动的FLW Flow 流量FURN Furnace: 炉膛FO :Fail Open: 故障时自动打开GLD Gland: 密封HB :Heat Balance: 热平衡（热工）ICV ::Inrtermediate ControlHD :Heater Drain:: 加热器疏水LIM(LMIR): Limiter: 限制器HDR :Header: 联箱Valve 中压控制阀ID :Induced Draft 抽LKG:: Leakage:: 泄漏HL ::Heat Loss: 热损失LP :Low Pressure 低压风，引风HMDY Humidity: 湿度IDF ::Induced Draft Fan: 引风机L.P :Low Point : 低位HPH: High Pressure Heater:高压加热器IGN ::Ignition: 点火装臵LPH: Low Pressure Heater: 低压加热器HPR :Hooper: 漏斗INL T :Inlet: 入口LSH: Local Switch Hand: 就地开关HPT :High Pressure Turbine: 高压汽机IPR ::Initial Pressure: 初压LUB: Lubricating Oil: 润滑油HR: Hot Reheat: 再热器热段INST :Instrument: 仪表M :Mechanical: 机械HR: Heat Rate: 热耗率INVR :Inverter: 逆变器M :Motor: 马达HSV: Hot Reheat Safety Valve: 再热器热I /O:: Input/Output 输入/ 输出MAG:: Magnetic: : 磁性段安全阀HVAC :Heating VentilationIP :Intermediate Pressure:中压MOD ::Mode: 方式:& Air Conditioning:: 暖通ISV ::Intermediate Pressure Turbine Steam M/A :Manual/Automatic: 手动/ 自动HW :Hotwell: 热井Valve: 中压缸进汽阀JP :Jet Pump: 喷MAN ::Manual :: 手动HV ::Hand Control Valve: 手动控制器MARG: Margin:: 裕量射器HYD :Hydraulic: 液力的LG :Level Gauge 液位计MAX ::Maximum: 最大的，最大值的INTLK :Interlock : 联锁LVL ::Level: 水位，液位MCR ::Maximum Continuous Rating 最大连续出力MCV:: Main Control Valve: IC :Instrument and Control:: 仪表与控制LA :Level Alarm: 液位报警主控制阀吸压头差压指示PDT :Pressure Differential MD :Modulation Damper: 调节挡板OL: Overload: 过载Trandsmitter: 差压变送器PED :Pdestal::MDBFP: Motor Driven Boiler Feedwater OLR :Overload Relay: 过载继电器轴承座Pump: 电动给水泵MEAS ::Measure : OPER :Operation: 运行PERF CALC Performance Calculation::测量OSC :Oscillograph: 示波器性能计算PF: Power Factor 功率因数MFT: Master Fuel Trip: 主燃料跳闸OTLT: Outlet: 出口PHTR: Preheater: 预热器MIN :Minimum: 最小的PA: Primary Air: 一次风PMP :Pump: 泵MKUP (MU) Make-up: 补充PAF :Primary Air Fan: 一次风机PNEU :Pneumatic: 气动的ML :Mill: 磨煤机PAH :Pressure Alarm High: 高压报警PR: Pressure Recorder:压力记录计MN :Main: 主要的PAL :Pressure Alarm Low: 低压报警PRG :Purge: 吹扫M.O. :Manual Operation: 手操PB: Push Button 按钮PRV :Pressure Relief Valve: 泄压阀MPT :Main Power Transformer: 主变压PC :Power Centre: 动力中心PRO :Protection: 保护器PC: Pressure Controller:压力控制器PROGR:: Program: 程序MS :Main Steam 主蒸汽P.C. :Pressure Control:压力控制PT: Pressure Transmitter:压力变送器MSV :Main Steam Valve: 主汽阀PCP :Precipitator 除尘器PULV: Pulverizer: 磨煤机NOZ: Nozzle: 喷嘴PCV :Pressure Control Valve:: 压力控制PVSV :Pressure Vacuum Safety Valve 压阀PDI :Pressure Differential Indication: 力真空安全阀PW: Plant Water 厂用水NPSH :Net Pump Suction Head: 泵的静PY: Pressure Relay: 压力继电器SEP :Separator分离器SW: Switch: 开关:QA: Quality:: 质量，性能SG: Switchgear 开关装臵Steam Water: 汽水RB: Run Back: 快速降负荷SH: Superheater: 过热器SBLWR: Soot Blower 吹灰器RCV :Recovering: 回收SLS :Seals:: 密封TBFP Turbine Drive Boiler Feedwater RECIRC:: Recirculation 再循环SO: Shut Off: 关闭Pump 汽泵TCV :Temperature Control RECT :Rectifier: 整流器SPD :Speed: 转速Valve 温度控制RET :Return: 返回SPRA: Spray: 喷水T.B.: Transfer Damper: 转换挡板RH: Reheater: 再热器SPT :Support: 支持: TE: Temperature Element:温度元件RO: Restriction Orifice: 节流孔板ST: Start: 启动，开始TG: Turbine-generator: 汽轮发电机ROT :Rotor: 转子STD-BY :Stand By: 备用Turbine-gear: Turbine-gear: 汽机盘车RTU :Remote Telemetry Unit:: 遥测装臵ST: System:: 系统THERM :Thermal 热力的SA :Secondary Air: 二次风STM :Steam: 蒸汽TMS: Turbine Master System: 汽机主控系统TRANS :Transfer: 转换SAT: Saturate: 饱和的STR: Stator:: 定子SC :Steam Coil Air Heater:: 暖风器STRNR: Strainer: 滤器TRBL: Trouble: 故障SCAV :Scavenge: 吹扫SU: Start Up: 启动TRKG: Tracking: 跟踪SD: Shut-off Damper: 关断挡板: SV: Solenoid Valve: 电磁阀TT: Temperature Transmitter: 温度变送Shut-Down 停机SUCT: Suction: 吸入器TTD: Terminal Temperature Difference: A/H ：AUTOMA TION/HAND : 自动/ DYNAMIC ；DYNAMICAL: 动态温度端差 F ：FLOW 流量;手动;TW: Thermowell: 热电偶套管A/M ：AUTOMA TION/MANUAL: 自FAST: 快动/ 手动;UAM :Unit Automatic Master: 机组自动FIGURE: 图示系统ALARM 报警; HIGH: 高VAC: Vacuum: 真空AUX ：AUXILIARY :: 辅助; HOT START —UP: 热态启动VAL: V a lue: 数值BYPASS 旁路I＆C ：INSTRUMENT AND CONTROL VB: Vibration 振动VL V: Valve: 阀门CLOSE 关（状态，常指阀门）;仪表与控制WH: Watthour 瓦小时CODE: 代码；编码INCREAS: 增加WP: Working Point: 工作点COLD START —UP: 冷态启动INDICA TION ；DISPLAY : 指示；显示; WW: Water Wall 水冷壁COMPUTER : 计算机WX: Watt Transducer: 功率转换器CURVE ，LINE: 曲线，线INLET 入口;COVER :Crossover 切换管DATA: 数据；文件；资料INPUT 输入;CV: Control Valve: 控制阀DECREAS : 减少INTERMEDIA TE 中DESK: 台，桌KEYBOARD: 键盘英汉对照表DIGIT: 数字KW ：KILOWA TT 千瓦DISK: 磁盘L ：LOAD 负荷，负载;LOC ：LOCAL : 就地PLANT: 厂，站START : 启动;LOW: 低POWER: 功率，电源; STARTUP : 起动；启动;MCS ：MANAGMENT COMMAND PRINT: 打印STATIC 静态SYSTEM 管理命令系统R ：RATE : 比率，速率; STATION 站MODE : 方式，模式R ：RESISTANCE: 电阻; STOP: 停止;MW ：MEGAWATT 兆瓦REM ：REMOTE : 摇控; SYMBOL 符号NORMAL: 正常RESET 复位SYSTEM: 系统OFF : 关（状态）; ROOM : 室T ：TEMPERATURE:: 温度;ON : 开（状态）; RPM:: 转/ 分; TEST: 试验;OPEN: 开( 状态，常指阀门); S ：SPEED 速度; TRANSMITTIER;TRANSDUCER: 变送OPERATE : 运行；操作; SELECT 选择器；传感器OUTLET 出口; SET POINT 设定点TRIP 跳闸;OUTPUT 输出; SHUTDOWN : 停机; TRIP ACKNOW: 跳闸确认P ：PRESSURE: 压力; SIDE （某）侧，边; UNAVAIL 不允许( 不能投用的) PANEL 盘SILENCER 消音器UNIT : 单元、机组PARAMETER : 参数SLOW : 慢VALVE 阀门PIPE ；TUBE: 管道，管子STAND BY: 备用; WARM START —UP: 温态启动ZOOM: 摄像机镜头ALARM LIMITS: :: 报警限制BOILER FOLLOW MODE: 炉跟随方ALL AIR HTRS RUNNING 各空预器运式行BOILER MASTER: 锅炉主控器锅炉部分ALL PUL V GRP SHUTDOWN 所有磨BOILER TRIP RESET: : 锅炉跳闸复位ACTUAL MEGAWA TT: 有功BOILER: 锅炉组停运AIR DRAFT SEQUENCE: : 风机程序控ASH —HOPPER: : 灰斗BURNNER: : 燃烧器制（顺控）ATTEMPERA TOR: : 减温器CHIMNEY ；STACK:: : 烟囱AIR HEA TER A MOTER: 空预器马达AUX .ST: SPLY FOR ATOMIZ 辅助蒸汽CLEAN: 清扫A COAL BANKER: :: 煤仓供雾化蒸汽AIR HEA TER LOC/REM SELECT: 空预BOIL MILL A BNR MET TEMP 炉 A COAL FEEDER : 给煤机器就地/ 遥控选择磨组喷燃器金属温度COMBUSTION : 燃烧AIR HEA T ER MOTOR LEAD: 空预器马BOIL MILL A GR1 WDBOX PR 炉 A CONVEYOR: 皮带机达选择磨组第一组风箱压力COORDINA TE MODE 协调方式AIR HTR A SEC AIR OUT TEM 空预器BOILER AIR REQUIRED 锅炉风量需求CRUSHER: 破碎机（>30% ）A 二次风出口温度DECR/INCR PRESS AT FIX LOAD:: 固AIR PREHEA T ER: 空预器BOILER EFFLUENT STORAGE: POOL定负荷方式增减压力AIR SVCE SUPPLY: 服务空气DOWM COMER:: 下降管锅炉废水池DRAIN & VENT: 疏水和排气FORCED DRAFT FAN : 送风机LUB OIL PUMP:: 润滑油泵ECONOMIZER : 省煤器FUEL GAS ID FAN A OUTLET PRESS A MAIN STEAM STOP VLV: 主蒸汽截EITHER FAN RUNNING : 任一风机运吸风机出口压力止阀行FURNACE PRESS: 炉膛压力MAIN STEAM EITHER ID FAN RUNNING 任一吸FURNACE: 炉膛TEMP/PRESSURE/FLOW 主汽温度/风机运行GAS COAL: :: 烟煤压力/ 流量ELECTROSTATIC PRECIPITATOR : 静HEADER : 联箱、母管MAINTAINED IGNITORS 电除尘器IGNITOR: : 点火器，油枪PULVERIZER A: 磨煤机 A 油枪操作FD FAN A FLOW:: A 送风机流量INDUCED DRAFT FAN : 引风机MANUAL LOAD SET/RATE:手动负荷设定/ 负荷率FD FAN/ID FAN A CONT DAMPER A INDUCED&FORCED DRAFTS: 吸送/ 吸风机控制挡板送风机MANUAL MODE: 手动方式FEED WATER FLOW: 给水流量INITIA TE: 启动、引燃、激发、触发MANUAL THROTTEL PRESS SET FEEDER LOCAL SELECT: 给煤机就地ISOLA TION: 隔离；绝缘POINT:手动节流压力设定值控制选择LFO .DISCH .PRESS : 轻油出口压力MILL A GROUP MASTER : A 磨组主控FEEDER REMOTE SELECT: 给煤机遥LIGHT OIL SEL GRP 1: 第一组轻油枪器控选择选择MILL A LOAD: A 磨组负荷FLUE GAS: 烟气LIGHT OIL: 轻油MILL A OUT TEMP CONT DAMPER : A磨组出口温度控制挡板PRI AIR FAN A CONT DAMPER: A 侧SELECT: 磨煤机正常方式选择MIN MAX LOAD （LIMITS ）: 最大PULVERIZER SELECTION A :: 磨煤机一次风机控制挡板最小负荷（限制）PRI AIR FAN A OUTLET PRESS A 一次 A 选择MMMC ＝MILLIMETER PULVERIZER: M/A: SELECT 磨煤机手风机出口压力MERCURY ；MMH2O: 毫米汞柱；PRI AIR FLOW MILL A CONT / 自动选择毫米水柱DAMPER 磨组一次风控制挡板PURGE 吹扫O 2 IN THE FUEL GAS 烟气含氧量PRI/SEC AIR FLOW MILL A A 磨组一RH ；REHEATER: 再热器次/ 二次风流量OPEN/CLOSE SWING VL V S 摆阀开SAFETY V ALVE:: 安全阀/ 关PRIMARY AIR FAN: 一次风机SCANNER BLOWERS: 火检吹扫器OPERATE MODE SELECT: 运行方式PRIMARY AIR SEQUENCE: 一次风控SEAL AIR FAN PRESS: 密封风机压力选择制SEAL AIR FAN:: : 密封风机PENDANT: : 悬吊管PULVERIZER : 磨煤机SEC AIR DUCT PRESS: 二次风管压PLATEN SPARY CONTROL VL VS SIDE PULVERIZER EMERGENCE TRIP 磨力A : 屏过减温水 A 侧控制阀SEC AIR FLOW MILL A CONT煤机紧急跳闸PLATEN SUPERHEATER: 屏过PULVERIZER INERT MODE SELECT: DAMPER A 磨组二次风流量控制挡板PRESSURE DIFFERENCE: 压差SEC SH OUT STEAM TEM 二级过热器磨煤机惰性方式选择PRI AIR DUCT PRESS 一次风管压力PULVERIZER NORMAL MODE出口蒸汽温度SEC SH SPARY CONT VLVS SIDE A SOOT BLOWER: 吹灰器STOP/START MILL: 磨组停止/ 启动二级过热器减温水 A 侧控制阀SPARK 火花，点火花STOP/START PA FLOW: 一次风停止SECONDARY SH INLET TEMP 二级过SPEED CHANGE (NOT) PERMISSIVE: / 启动热器进口温度速度切换（不）允许STOP/START PULVERIZER 磨煤机停止/ 启动SECONDARY: AIR 二次风SPRAY : 喷水SH ；SUPERHEATER: : 过热器STACKER RECLAIMER :: 堆取料机STOP/START SEQUENCE SH STEAM ELECTR VL V: 过热器电START IGNITOR GRP 1: 第一组油枪点PULVERIZER A: 磨煤机 A 程序停磁阀火止/ 启动SH STEAM TEMP SET POINT:: 过热温STEAM DRUM: : 汽包THROTTLE PRESS:: 节流压力度设定点STEAM 蒸汽TRANSPORT AIR SEQUENCE 风量程SH/RH SPARY WATER STOP VLVS:: 过STONE COAL: 无烟煤序控制（顺控）热器/ 再热器减温水截止阀STOP IGNITORS GRP 1: 第一组油枪停TURB FIRST STAGE PRESS 汽机第一级( 调节级) 压力SH/RH SPRAY CONTROL VL V S 止SELECT 过热器/ 再热器减温水控制STOP/START FEEDER 给煤机停止/ TURBINE FOLLOW MODE: 机跟随阀选择启动方式SLIDING PRESS MODE: 滑压运行方STOP/START IGNITORS: 油枪停止/ TURBINE MASTER: 汽机主控器式启动TWIN FLOW AIR HTR A CONT VL V: :双流式空预器控制阀BALANCE: : 平衡汽器抽空气阀UNLOADER: :: 卸煤机BEARING BRASS:: 轴瓦CONDENSER HOT WELL: : 热井WATER 水BEARING: : 轴承CONDENSER LEVEL CONTROL VLV: WATERWALL: : 水冷壁BLADE 叶片凝汽器水位控制阀汽机部分BOILER FOLLOW MODE: 锅炉跟随方CONDENSER: 凝汽器:EMERG OIL PUMP: 事故油泵CONDS EXTR PUMP DISCH : 凝结水式<P>CICR PMP DISCHARGE VL V: 循环BOOSTER FEED PUMP: 前臵给水泵抽吸泵出口泵出口阀CICR WTR PUMP: 循环泵CONDS STOR TANK LEVEL: 凝结水储1ST STAGE PRESS: 第一级压力CIRCULA TING PUMP: : 循环泵水箱水位ACTUAL MEGA WA TT: : 实际负荷数CIRCULA TING: 循环COOLER: : 冷却器AMS ：ADMISSION: MODE CLOSED COOLING WATER: 闭式冷却COOLNG WTR PUMP: 水冷泵SELECTION 进汽方式选择COORDINA TE MODE: : 协调方式水AUX STEAM HEADER: : 辅汽联箱CLOSED COOLING WTR PUMP: 闭式CV ：CONTROL V ALVE 高压调门AUX STEAM TEMP CONTROL: 辅汽CYLINDER 、CASING: 汽缸冷却水泵温度控制CMPTR: : 计数器DEAERA T OR LEVEL CONTROL VLV: AUX STM HEADER PRESS CONTROL CONDENSATE PUMP: 凝泵除氧器水位控制阀VLV 辅汽联箱压力控制阀CONDENSER AIR SUCTION VL V: 凝DEAERA T OR: : 除氧器DECR PRESS AT FIX LOAD: 在负荷不给水控制阀的旁路阀高压旁路及减温水阀变下减压FW FLOW 30% CONTROL VLV : 30% HP BYPASS PRESS CONTROL VL V 高DEMI WA TER: 除盐水给水控制阀旁压力控制阀DISPATCH PARTICIPATION 调度（参FW FLOW MASTER CONTROL: 给水HP BYPASS PRESS SET POINT: 高旁压与）指令流量主控力设定值DURM PRESSURE:: 汽包压力FW HP HTR DISCH TEMP: 给水高加出HP BYPASS TEMP CONTROL VAL V EEJECTOR: 喷射器，抽气器口温度高旁温度控制阀EMERGENCY GOVERNOR 危急保安FW PUMP RECIRCUL CONTROL VLV HP＆LP BYPASS COMMAND 高压及器给水泵循环控制阀低压旁路指令EXHAUST: 排汽FW VL V: 给水阀门HPH ：HIGH PRESSURE HEATER : 高EXPANSION: 膨胀GEARING: 盘车加EXTR ST TO HP HTR 抽汽至高加GOVERNOR: 调速器HYDRAULIC OIL STATION PUMP: 液EXTRACTION STEAM 抽汽HP ATTEM PRESS CONTROL VL V: 高压油站泵FIL T ER: : 滤网INCR PRESS AT FIX LOAD: 在负荷不旁减温水压力控制阀FLANGE 法兰HP ATTEMP BLOCK VLV: 高旁减温水变下增压FUNCTION GROUP: 功能组INT POS: 中间状态闭锁阀FW CONTROL V AL V E ' S BYPASS VL V: HP BYPASS ＆HP ATTEMP VL V S: IV ：INTERMEDIA TE VAL VE 中压联合汽门MOTOR DRIVEN FEED WA TER PUMP RH SPRAY WTR STOP VLVS: 再热器JACKING OIL PUMP 顶轴油泵电动给水泵喷水截止阀LP HTR STOP VLV 低加截止阀MSV ：MAIN STOP V AL V E: 主汽阀RH STEAM ATTEM FLOW: 再热喷水LP ＆HP BYPASS PRESS SIDE A 低压NOZZLE 喷嘴流量或高压旁路 A 侧压力OIL PURIFIER: 净油器RH STEAM TEMP OUTLET: 再热器出LP ＆HP BYPASS TEMP SIDE A 低压OIL STORAGE TANK : 储油箱口温度或高压旁路 A 侧温度OPERATE MANUAL MODE: 手动方式ROTOR 转子LPH ：LOW PRESSURE HEATER: OPERATE MODE SELECT: 运行方式选SEAL: 密封低加择SHAFT 轴LUBE OIL PUMP: 润滑油泵PILOT V ALVE: 错油门SILENCER: 消音器MAKE －UP WATER: 补给水PLATEN SH INLET TEMP SIDE A: A 侧SLIDING PRESS MODE: 滑压方式MANUAL LOAD RA TE 手动负荷率SPEED INDICA TOR OR SPEED屏过入口温度MANUAL LOAD SET 手动负荷设定PRIMARY SH STOP VAL V E: 一级过热METER: : 转速表MANUAL Throttle Press Set Point 手动节STATOR 定子器截止阀流压力设定值PUMP A DISCH PRESS : A 泵出口压力STEAM TURBINE : 汽轮机MEASURE SELECTION 测量选择站RH SPRAY BLOCK VL VSTRIP INIT 再ST －UP BOIL FDW PUMP: 启动给水MOP ：MAIN OIL PUMP: 主油泵热器喷水闭锁阀跳闸启动泵SUCTION PUMP: 抽吸泵AMPERE: 安培方式SURGE APPROACH: 喘振VACCUM 真空ANGLE OF LAG: 滞后角SYNCHRONIZER: 同步器VACUUM BROKEN VAL VE: 真空破坏ANGLE OF LEAD: 超前角TFW PMP DISCHARGE VL V: 汽动泵出ANODE: 阳极门口阀VACUUM SEQ : 真空程控ARC: 电弧TFW PUMP MAIN OIL PMP: 汽动给水VIBRA TION: 振动ARMA TURE 电枢泵的主油泵电液调节及控制部分AST ：AUTO SHUT-DOWN TRIP: 自THROTTLE ORIFICE 节流孔板1STAGE PRESSURE FEEDBACK: 第一动停机遮断TURBINE DRIVEN FEED WATER ASYNCHRONOUS MOTOR: 异步电动级压力反馈PUMP: 汽动给水泵ABNORMAL CONDITION: 异常状态机TURBINE FW PUMP AUX ＆VLV 小ACCELERA TION: 加速度AT SET SPEED: 在设定速度位臵机给水泵辅汽及阀门ACTIVE POWER:: 有功功率ATC ：AUTO TURBINE CONTROL:TURBINE GENERA TOR: 汽轮发电机组ADMISSION MODE: 进汽方式自动汽轮机控制TURBINE INLET PRESS: 汽机入口压ADS(ALARM DISPLAY SELECT AUTOFORMER: 自藕变力PANELS) 报警显示选择屏AUTORECLOSING : 自动重合闸TURBINE MASTER : 汽机主控器AERIAL LINE: 架空线AUXI TRANSFORMER : 厂用变TURBING FOLLOW MODE: 汽机跟随ALTERNA T ING CURRENT (AC): 交流BACK UP TRANSFORMER 备用变BACK-UP OVERSPEED TRIP TEST 备BUSHING 套管合阀用超速跳闸试验ELECTRICAL TRIPCABLE 电缆COMMON SERVICES LOGIC SUITE::TEST 电气跳闸试验CAPACITANCE: 电容公用系统逻辑柜BACK-UP SPDSIG LOST: : 后备速度信CARRIER 载波COMMUNICA TION: 通讯号失去CATHODE : 阴极CONDUCTOR : 导体BARRING OIL PUMP 盘车油泵CCR: 中控室CONFIGURA TION: 结构，布臵，外形: BASE LOAD: 基荷CHARGING EQUIPMENT : 充电设备CONTROL OIL: 控制油BATTERY : 电池CHEST /ROTOR WARMING: 腔室/ CORE: 铁芯BATTERY BACKED CLOCK 电池备用CPU(CENTARL PROCESSING UNIT:转子预暖时钟CIU : 计算机接口单元中心处理单元BDV ：BLOWDOWN VL V: 泄放阀CLOSE : 合闸CRT: 显示屏BOOSTER PUMP: 前臵泵CLOSED VAL V ES OVERSPEED TEST CURRENT TRANSFORMER: 电流互感BULB : : 灯泡关闭阀超速器BUS SECTION : 母线分段CLOSED-LOOP : 闭环CURRENT 电流BUS: 母线COIL:: 线圈CV:: 控制阀BUSBAR FRAME: 母线架COMBINED RECLOSING 综合重合闸DAS: 数据采集系统BUSCOUPLER: 母联COMBINED REHEA T V ALVES: 中压联DECREASING LOAD RATE: : 减负荷率危急跳闸系统GENERATOR : 发电机DIESEL GENERATOR : 柴油发电机EXCEPTION REPORT: 例外报告GROUNDING(EARTHING) 接地DIRECT CURRENT (DC) 直流EXCITE 励磁H2 TEMP CONT V : 氢气温度控制阀DISCONNECTOR : 隔离开关EXCITOR 励磁机HARDWARE 硬件DISTRIBUTED CONTROL SYSTEM: FA/PA POSITION : 全周/ 部分（进HOLD: 保持分散控制系统汽）位臵HYDRAULIC FLUID PRESS: 抗燃油压E.W.S.: 工程师工作站FAST-ACTING SOLENOID: 快动电磁力EHC STATUS: 电液调节系统状态I.C.S: 数字控制站终端模件阀EHC ：ELECTRO-HYDRA CONTROL FIRST STAGE PRESS 调节级压力IN STANDBY: 在备用状态SYSTEM: 电液调节控制系统FIS :: 流量显示开关IND: :: 指示器EHV MIMIC PANEL : 电气高压模拟屏FREQUENCY: 频率INDUCTANCE: 电感ELECTRICAL MALFUNCTION FRF ：FIRE RESISTANT FLUID:: 抗燃INHIBITED: 停止进行、禁止SYSTEM FAUL T : 电气失灵系统故障INSULA TOR 绝缘子油EMERGENCY OIL PUMP: 事故油泵FULL ARC : 全周进汽INTERCEPT V ALVE: 中间截流阀EMERGENCY SEAL OIL PUMP: 事故GAS : 瓦斯INTERCEPT V ALVES: 中间截止阀密封油泵GEN. SHAFT SEAL&STATOR INTERFACE 接口ETS ：EMERGENCY TRIP SYSTEM: WIND : 发电机密封及静子绕组KILOWA TT 千瓦LC: 液位控制器LOSS : 损耗NEUTRAL POINT: 中性点LI: 液位显示LOSS OF PWR:: 失去电源OHM: 欧姆LIGHT: 照明LVDT ：线性位移差动变送器OIL GAUGE: 油位表LINE 线路MAGNETIC FIELD: 磁场OPC ：OVERSPEED PROTECTION LK: 液位控制站MAIN OIL PUMP: 主油泵CONTROL: 超速保护控制LOAD DECREASING ；AT SET MAIN SEAL OIL PMP : 主密封油泵OPEN-LOOP : 开环LOAD 负荷减；在设定负荷MAIN STEAM PRESS 主蒸汽压力OPER AUTO: 操作员自动::LOAD FLOW : 负荷潮流分布MAIN TRANSFORMER STEP-UP OPERATING MODE : 操作方式LOAD INCREASING: 负荷增TRANSFORMER: 主变ORP ：OIL RESET PISTON: 油复位活LOAD LIMITING SET: 负荷极限设定MANUAL: 手动塞LOAD MONITORING: 负荷监视MCC: 马达控制中心ORSV ：OIL RESET SOLENOID VL VLOAD SELECT: :: 负荷选择MEGAWATT: 兆瓦油复位电磁阀LOAD SET: 负荷设定MFP : 多功能控制器OTSV ：OIL TRIP SOLENOID VL V: 油LOAD: 负荷MOTOR: 电动机跳闸电磁阀LOADING RA TE LIMIT : 负荷（增、MSPL ：MAIN STEAM PRESSURE OVER CURRENT: 过流减）率限定LIMITER : 主汽压力限制器OVER VOL TAGE : 过压LOCKED OUT: 闭锁MSV: 主蒸汽阀OVERLOAD: 过载PART ARC : 部分进汽POWER FACTOR: 功率因数RSV: 再热汽截止阀PC: 动力中心POWER LOAD UNBALANCE: 功载不SAFELY OIL : 安全油PDIS : 压差显示开关SCR CONTROLLER: 可控硅整流控制平衡PEAK LOAD: 峰荷PP ：: PREESSURE POINT 压力检测点器PERMANENT MAGNETIC PRI SPD SIG LOST 一次速度信号失SEAL OIL: 密封油GENERATORDF 永磁发电机SHUT-OFF VALVE:: 切断阀去PG: 压力计PS: 压力开关SIGNAL: 信号PHASE ANGLE : 相角PT: 压力变送器SLOW MEDIUM FAST: 慢、中、快PHASE: 相REACTANCE: 电抗SPEED INCREASING: 速度增PIC: 压力显示控制器REACTIVE POWER: 无功功率SPEED MONITORING: 速度监视PK: 压力控制站RECLOSING : 重合闸SPEED SET RPM : 转速设定转/ 分PLUG : 插头REHEAT PRESS:: 再热汽压力SPEED: 速度，转速PLUG SOCKET: 插座REMOTE AUTO: 远方自动START UP TRANSFORMER 启动变POLE:: 电极REMOTE OPERATION : 远操STATOR WIND COOLING WATER POTENTIAL TRANSFORMER 电压互RESISTANCE: 电阻PUMP: 定子绕组冷却水泵感器RSM ：ROTOR STRESS STEAM SEAL BY-PASS UNLOAD VL V:POWER 功率MONITORING: 转子热应力监视:蒸汽密封旁路泄放阀STEAM SEAL DIVERING VAL V: 密封TIC :: 温度指示控制盘车控制程序汽分流阀TIME DELAY: 时间延迟TURN GEAR MOTOR: 盘车主电机STEAM SEAL SYS:: 蒸汽密封系统TP: 温度检测点TURN GEAR PIGGY :BACK MOTORSUCTION PMP A/M SEL: 抽吸泵手/ TRANSFER AND FIL T ER PUMP: 输送盘车啮合电机自动选择和过滤油UNINTERRUPTED POWER SUPPLY:SUCTION PUMP: 抽吸泵TRANSFORMER: 变压器不间断电源SUPERVISORS DESK: 值长台TRANSMISSION: 传输UNIT CONTROL DESK: 机组控制台SWITCH 开关TRIP 跳闸UNIT TRANSFORMER:: 单元变SWITCHGEAR : : 配电盘、开关装臵TS: 温度开关VACUUM TRIP: 真空跳闸TELEPHONE: 电话TSI: 汽机监视仪表VALVE POSITION: 阀位臵TEST SELECT: 试验选择（联锁）TT:: 温度变送器VI : 阀位臵指示THERMO-COUPLE: : 热电偶TURB LUBE OIL TEMP CONTROL V : VOLT(V): 伏特THREE ELEMENTS LEVEL VOLTAGE 电压汽机润滑油温度控制阀CONTROLLER: 三冲量水位控制器TURBIN DRAIN VAL VES: 汽机疏水VT: 阀位臵变送器THRUST BEARING WEAR DETECTOR VV ：VENTILA TING V ALVE : 通风阀阀TEST 推力轴承磨擦检测试验TURBINE LA TCHED: 汽机挂闸WARMING RA TE: 暖机速率TI : 温度显示器TURN GEAR CONTROL SEQUENCE WATT: 瓦特WINDING: 绕组。
火力发电厂英语词汇大全
电力英语一、锅炉部分1．临界压力锅炉supercritical pressure boiler2. 亚临界压力锅炉subcritical pressure boiler3. 超高压锅炉super-high pressure boiler4. 蒸汽锅炉steam boiler5. 蒸汽发生器steam generator6. 液态排渣锅炉wet bottom boiler7. 固态排渣锅炉dry bottom boiler8. 燃煤锅炉coal-fired boiler9. 燃气锅炉Gas-fired boiler10.燃油锅炉oil-fired boiler11.自然循环锅炉natural circulation boiler12.汽包（锅筒）锅炉drum boiler13.强制循环锅炉controlled circulation boiler14.直流锅炉once-through boiler15.复合循环锅炉combined circulation boiler16.旋风炉cyclone furnace boiler17.沸腾炉fluidized bed combustion(FBC)boiler18.循环硫化床circulating fluidized bed combustion(FBC)boiler19.增压循环硫化床锅炉 pressurized circulating fluidized bed combustion(PCFBC)boiler20.链条锅炉chain-grate boiler21.热水锅炉hot-water boiler22.废热（余热）锅炉water-heat boiler, heat recover steam generator(HRSG)23.启动锅炉start-up boiler24.厂用锅炉auxiliary boiler25.垃圾焚烧锅炉refuse-fired boiler, refuse incinerator27.露天锅炉outdoor boiler28.单炉膛锅炉single furnace boiler29.双炉膛锅炉twin furnace boiler30.W火焰锅炉W-flame boiler, vertical-fired boiler31.L火焰锅炉L-shape furnace boiler32.塔式锅炉tower boiler33.箱式锅炉box-type boiler34．炉墙furnace wall35. 汽包（锅筒）drum36.封头head37.汽包封头drum end plate, drum head38.下降管downcomer39.集中下降管centralized downcomer40.分散下降管distributed downcomer41.上升管riser42.管束（排）tube bundle43.管屏tube platen44.省煤器管economizer tube45.过热器管superheated tube46.再热器管reheater tube47.蛇形管coil48.吊挂管supporting tube49.引入管inlet pipe50.引出管outlet pipe51.饱和蒸汽管saturated steam pipe52.水冷壁管water wall tube53.鳍片管finned tube, fin tube, gilled tube54.内螺纹管rifled tube, grooved tube55.吸潮管moisture absorption piping56.水冷壁water wall57.膜式水冷壁membrane wall58.内螺纹水冷壁rifled tube water wall59.联箱header60.集汽联箱steam header61.卫燃带bailey wall, refractory belt62包墙管（包覆管）wall enclosure tube63.防渣管（弗斯顿管）slag screen, feston tube64.锅炉本体boiler proper65.锅炉机组boiler unit66.锅炉构架boiler structure67.炉膛boiler framework68.燃烧器furnace69.直流式燃烧器direct-flow burner70.旋流式燃烧器turbulent burner71.低NOX燃烧器low NOX burner72.摇摆式燃烧器tilting burner73.缝隙式燃烧器split burner74.燃烧室combustion chamber75.油枪oil gun torch76.风门damper77.一次风primary air78.二次风secondary air79.三次风tertiary air80.煤粉管道pulverized coal piping81.管板tube plate82.沸点boiling temperature83.过热器superheater84.前屏过热器front platen superheater85.后屏过热器rear plate superheater86.对流过热器convection superheater87.辐射过热器radiant superheater88.屏式过热器plate superheater89.顶棚过热器ceiling superheater90.包墙过热器wall enclosure superheater91.前包墙过热器front wall enclosure superheater92.后包墙过热器rear wall enclosure superheater93.侧包墙过热器side wall enclosure superheater94.吹灰器soot blower95.转动式吹灰器rotary soot bolwer96.伸缩式吹灰器retractable soot blower97.受热面积heating surface area, heat absorption area98.炉膛容积furnace volume99.炉膛热负荷furnace heat release rate, furnace heating absorption rate 100.汽水分离器steam separator, moisture separator101.起动分离器starting separator102.再循环管recirculating piping103.暖风器steam air heater104.再热器reheater105.再热器冷段primary reheater106.再热器热段final reheater107.顶棚ceiling108.省煤器economizer109.管式省煤器tube economizer110.管式空气预热器tubular air preheater111.回转式（再生式）空气预热器regenerative air preheater, rotary air preheater 112.板式空气预热器plate air preheater113.空气预热器air preheater114.三分仓空气预热器trisector regenerative air preheater115.漏风系数air leakage coefficient116.漏风率air leakage ratio117.漏风系统air leakage system118.漏风试验air leakage test119.安全门safety valve120.安全门开启压力opening pressure of safety valve121.安全门回座压力safety valve reseating pressure122.安全门压力整定试验pressure setting test of safety valve123.安全门动作压力safety valve operating pressure124.饱和蒸汽安全门saturated steam safety valve125. 过热蒸汽安全门superheated steam safety valve126.再热蒸汽安全门reheated steam safety valve127.防暴门explosion vent128.检查孔inspection hole129.事故喷水阀emergency water spray valve130.汽包事故放水阀emergency drum drain valve131.三通阀three-way valve132.反冲洗阀back wash valve133.取样阀sampling valve134.插板gate135.给水大旁路门feedwater overall bypass valve136.给水小旁路门feedwater individual bypass valve 137.大板梁plate girder, upper beam138.外护板outer casing139.锅炉排污blowdown140.定期排污扩容器intermittent blowdown flash tank 141.连续排污扩容器continuous blowdown flash tank 142.灰斗ash hopper143.冷灰斗bottom ash hopper, furnace hopper 144.混合器mixer145.齿圈（大牙轮）ring gear, geared ring146.空调器air conditioner147.空气压缩机air compressor148.给煤机coal feeder149.皮带式给煤机belt coal feeder150.刮板式给煤机scraper coal feeder151.叶轮式给煤机paddle coal feeder152.给粉机pulverizer coal feeder153.磨煤机coal pulverizer, coal mill154.钢球磨煤机tube mill155.中速辊式磨煤机roller mill, bowl mill, disk roll mill 156.双进双出钢求磨煤机double inlet and outlet tube mill 157.中速磨煤机medium speed mill158.风扇磨煤机beater wheel mill, beater mill159.排粉风机pulverized coal exhauster160.一次风机primary air fan161. 烟气再循环风机gas recirculation fan162.送风机forced draft fan, force fan163.引风机induced draft fan, induced fan164.离心风机centrifugal fan165.轴流风机axial-flow fan166.双速风机double speed fan167.轴流静叶可调风机adjustable static-blade axial-flow fanfixed pitch axial-flow fan168.轴流动叶可调风机adjustable moving-blade axial-flow fanvariable pitch axial-flow fan169.原煤斗raw coal bunker, raw coal silo 170.煤粉仓pulverized coal bunker171.输粉机pulverized coal conveyer172.刮板输粉机scraper pulverized coal conveyer 173.螺旋输粉机pulverized coal screw conveyer 174.粗粉分离器classifier175.细粉分离器（旋风分离器）cyclone separator176.锁气器air lock, flap177.减速机speed reduce178.看火孔observation hole179.人孔门man hole180.重油泵heavy oil pump181.重油加热器heavy oil heater182.汽-汽热交换器biflux183.煤气罐gas tank184.膨胀补偿节expansion joint185.直吹式制粉系统direct firing pulverizing system 186.中贮式制粉系统bin storage type pulverizing system 187.锅炉效率boiler efficiency188.锅炉热力计算boiler thermodynamic calculation 189.锅炉空气动力计算boiler aerodynamic calculation 190.锅炉水循环计算boiler water circulation calculation 191.锅炉水力计算boiler hydrodynamic calculation 192.锅炉强度计算boiler strength calculation193.锅炉热平衡boiler heat balance calculation 194.正平衡法direct balance method195.反平衡法indirect balance method196.过剩空气系数excess air coefficient197.排烟温度flue gas temperature198.单位蒸量specific evaporation199.低温腐蚀low temperature corrosion200.高温腐蚀high temperature corrosion201.结渣lagging202.结垢腐蚀deposit corrosion203.飞灰磨损fly ash erosion204炉膛负压furnace draft205.最高允许温度maximum permissible temperature 206.炉膛正压furnace pressure207.水循环water circulation208.循环倍率circulation ratio209.除尘器dust collector, precipitator210.静电除尘器electrostatic precipitator211.整流装置rectifying device212.锤打装置rapping gear213.含尘浓度dust loading concentration214.煤灰细度dust fineness215.除尘效率dust collection efficiency216.干式除尘器dry dust collector217.湿式除尘器wet dust collector, scrubber218.文丘里除尘器venture scrubber219.布袋除尘器fabric filter, bag house220.钢珠除尘装置shot-cleaning device221.水膜式除尘器centrifugal scrubber222.灰渣泵ash pump, slag pump223.轴封泵shaft sealing pump224.灰浆泵ash slurry pump225.除尘水泵dedusting pump226.回收水池water recovery pond227.清水池clean water pond228.灰浆池ash slurry pond229.油泵坑oil pump pit230.灰库ash silo231.灰场ash yard232.灰坝ash yard dam233.耐火砖firebrick234.保温材料heat-insulating material235.干式除灰（气力除灰）pneumatic pressure ash handling 236.水力除灰hydraulic ash handling237.正压气力除灰pneumatic pressure ash handling 238.负压气力除灰pneumatic pressure ash handling 239.仓式泵fluidizing transporter240.空气斜槽airslide, air gravity conveyor241.灰渣分除bottom and fly ash separate handling 242.灰渣混除bottom and fly ash mixed handling 243.灰渣利用bottom and fly ash recovery244.排渣槽bottom ash hopper245.埋刮板捞渣机submerged slag conveyor246.螺旋式捞渣机screw slag conveyor247.碎渣机clinker grinder, slag crusher248.振动筛vibrating screen249.稳燃器flame stabiliaer250.燃烧器蜗壳burner spiral case251.雾化器atomization252.机械雾化mechanical atomization253.蒸汽雾化steam atomization254.空气雾化air atomization255.气固两相流动gas-solid two-phase flow256.闭路循环closed cycle257.蒸汽带水carryoery258.炉膛灭火boiler flame failure, boiler flame blackout259.稳定燃烧stable combustion260.压力容器pressure vessel261.支吊架supports and hangers262.原煤管道raw coal piping263.风道air duct264.热风道hot air duct265.冷风道cold air duct266.穿墙套管wall-through bushing, wall-bushing267.伸缩节expansion joint268.送粉管道pulverized coal feed piping269.燃油管道fuel oil piping270.风管道air piping271.一次风管道primary air piping272.二次风管道secondary air piping273.落粉管pulverized coal chute274.除灰管道ash piping275.烟道gas dust, gas pass276.尾部烟道convection flue gas pass277.煤气管gas piping278.连续排污管continuous blowdown piping279.烟囱chimney, stack280.多管式烟囱multi-flue chimney281.燃烧combustion282.四角喷射燃烧corner firing283.燃烧速度combustion rate284.机械未完全燃烧热损失heat loss due to mechanical incomplete combustion 285化学未完全燃烧热损失heat loss due to chemical incomplete combustion 286.灰渣热损失heat loss due to sensible heat in refuse287.排烟热损失heat loss due to flue gas288.散热损失heat loss due to radiation289.热损失heat loss290.火焰flame291.不稳定燃烧instable combustion292.负压燃烧balance draft combustion293.微负压燃烧pressurized combustion294.炉膛容积热负荷furnace volume heat release rate295.炉膛温度furnace temperature296.锅炉水循环boiler water circulation297.偏离泡核沸腾departure from nucleate boiling(DNB)298.水压试验hydraulic test299.汽水共沸priming300.点火ignition301.点火准备ignition preparation302.着火点firing point, ignition temperature303.折焰角nose304.飞灰fly ash305.煤粉细度fineness of pulverized coal306.灰ash307.灰的熔化点ash fushion temperature, ash fushion point, ash melting point308.可磨系数grindability index309.最大蒸发量maximum evaporation310.锅炉热平衡boiler heat balance311.超负荷运行overload operation312.正压positive pressure313.负压negative pressure314.理论空气量theoretical air quantity315.过剩空气量excess air quantity316.冷风cold air317.热风hot air318.除渣slag removal319.烟气flue gas320.锅炉上水boiler water filling321.蠕胀爆管tube burst due to creep322.汽包满水overfeed of water into drum323.锅炉灭火boiler fire extinction324.爆燃puff325.爆炸（外爆）explosion326.内爆implosion327.防爆anti-explosion328.煤粉自燃pulverized coal self-ignition, pulverized coalspontaneous combustion329.堵灰ash fouling330.堵煤coal jamming, coal plugging331.燃烧切圆firing tangential circle332.火焰中心flame center333.积粉pulverized coal deposits334.粉灰ash deposits335.飞灰可燃物combustibles in fly ash336.点火用油fuel oil for ignition337.飞灰腐蚀fly ash corrosion338.受热面heating surface339.辐射受热面radiation heating surface340.对流受热面convection heating surface341.尾部受热面rear heat recovery surface342.含氧量oxygen content343.蒸发量evaporation, evaporative capacity 344.切换风air switch-over345.煤耗率coal consumption rate346.入炉煤发热量heating value of the as fired coal 347.停炉boiler shutdown348.熄火fire-off349.灰水回收recovery of ash slurry water 350.细灰fine ash351.粗灰coarse ash352.干灰dry ash353.湿灰wet ash354.燃烧系数combustion system, firing system 355.制粉系统coal pulverizing system356.除灰系统ash handling system电力英语二、汽轮机357.汽轮机steam turbine358.凝汽式汽轮机condensing steam turbine359.背压式汽轮机back pressure turbine360.抽汽式汽轮机steam extraction turbine361.中间再热式汽轮机reheating type steam turbine362.供热式汽轮机steam supply turbine, heat supply turbine, cogeneration turbine363.冲动式汽轮机impulse turbine364.反动式汽轮机reaction turbine365.轴流式汽轮机axial flow turbine366.辐流式汽轮机radial flow turbine367.单轴汽轮机tandem compound turbine, single-shaft turbine368.双轴汽轮机double-shaft turbine, cross compound turbine369.前置式汽轮机topping turbine370.燃气轮机gas turbine371.高压汽轮机high pressure turbine372.中压汽轮机medium pressure turbine373.低压汽轮机low pressure turbine374.超高压汽轮机ultra pressure turbine375.亚临界压力汽轮机subcritical pressure turbine376.超临界压力汽轮机supercritical pressure turbine377.空冷式汽轮机组air cooled turbine unit378.燃气轮机组（装置）gas turbine unit379.高压汽缸high-pressure(HP) cylinder380.中压汽缸intermediate-pressure(IP) cylinder381.低压汽缸low-pressure(LP) cylinder382.内汽缸inner casing383.外汽缸outer casing384.上汽缸upper casing385.下汽缸lower casing386.汽缸法兰螺栓加热装置cylinder flange heating appliance387.汽缸台板（底板）cylinder sole pin388.汽缸猫爪cylinder claw389.滑销sliding pin390.横销traverse pin391.纵销longitudinal pin392.立销vertical pin393.定位销aligning pin, locating pin394.汽轮机转子turbine rotor395.叶轮 impeller396.叶片blade,397.动叶片moving blade398.静叶片stationary blade399.叶根型式type of blade root400.末级叶片长度length of last stage blade401.喷嘴室nozzle box402.末级叶片强度last stage blade stress403.排汽室steam exhaust hood404.喷嘴nozzle405.围带shroud ring406.拉筋（拉金）lacing wire407.平衡块balance weight408.固定螺钉dowel409.隔板diaphragm410.隔板套diaphragm sleeve411.隔板汽封diaphragm seal, diaphragm sealing412.汽封steam seal gland, steam sealing413.迷宫式汽封labyrinth seal414.梳齿式汽封serrate-type steam seal415.汽封套seal bushing416.汽封块seal block417.汽封齿seal tooth418.轴承支架bearing stoll, bearing bracket419.主轴承箱main bearing box420.滚珠轴承ball bearing421.滚柱轴承roller bearing422.滑动轴承sliding bearing423.推力轴承thrust bearing424.止推环thrust collar425.瓦枕bearing pillow426.锁饼lock427.推力瓦块thrust bearing pad428.主油泵main oil pump429.备用油泵emergency bearing oil pump430.调速油泵regulation oil pump, speed governing oil pump 431.交流润滑油泵AC lube oil pump432.直流润滑油泵DC lube oil pump433.注油器oil injector434.同步器synchronizer435.同步器手轮synchronizer hand wheel436.控制滑阀pilot valve437.随动滑阀servo-valve438.分配滑阀distributing pilot valve, distributor valve439.中间滑阀intermediate valve440.微分器differentiator441.功率限制器load limiter442.动态校正器dynamic corrector443.滑阀套valve sleeve444.喷油嘴oil nozzle445.弹性调速器flexible governor446.调速器挡块governor stop447.危急遮断器滑阀emergency trip pilot valve448.撞击子ram449.防火滑阀fire protection pilot valve450.延滞滑阀delay pilot valve451.跟踪滑阀follow-up pilot valve452.电-液转换器electro-hydraulic converter, electro-hydraulic transducer 453.切换滑阀change-over pilot valve454.危急保安器emergency governor455.危急保安器滑阀emergency governor pilot valve456.超速试验滑阀overspeed test pilot valve457.喷油试验滑阀nozzle test pilot valve458.反馈滑阀feedback pilot valve459.起动排油阀oil drain valve at star-up460.紧急放油阀emergency oil relieve valve461.排油口oil diacharge outlet462.节流滑阀throttle pilot valve463.滑动油阀movable pilot valve464.高压自动关闭器high-pressure automatic closing gear465.中压自动关闭器medium pressure automatic closing gear466.高压油动机（高压伺服马达） high-pressure hydraulic actuator, high-pressure servo-motor467.中压油动机medium-pressure hydraulic actuator, medium-pressure servo-motor468.杠杆lever469.轴shaft470.主轴main shaft471.传动轴(主动轴) driven shaft472.被动轴（从动轴）driven shaft473.小轴axle474.联轴器coupling475.刚性联轴器rigid coupling476.半挠性联轴器semi-flexible coupling477.齿型联轴器serrated coupling478.冷油器oil cooler479.溢油器oil overflow valve480.排油烟机oil-fume extractor, oil fume exhaust 481.油烟分离器oil-fume separator482.油净化器oil purifier, oil conditioner483.过滤罐filtering tank484.布袋式过滤器bag filter, fabric filter485.齿轮油泵gear oil pump486.顶轴油泵jacking oil pump487.柱塞式油泵piston type oil pump488.螺杆式油泵worm type oil pump489.盘车装置turning gear490.盘车手轮turning gear hand wheel491.化桩板lagging enclosure492.齿轮gear493.直齿式齿轮spur gear494.斜齿式齿轮helical gear495.伞型齿轮bevel gear496.蜗轮worm wheel497.蜗杆worm stem498.弹簧spring499.密封油箱sealing oil tank500.空气侧交流密封油泵air side AC sealing oil pump 501.空气侧支流密封油泵air side DC sealing oil pump 502.压差阀differential pressure valve503.平衡阀balancing valve504.密封瓦sealing pad505.缓冲油箱buffer oil tank506.高位油箱head oil tank, elevated oil tank 507.事故油箱emergency oil tank508.磁性过滤器magnetic filter509.发电机内冷水箱generator inner cooling water tank 510.发电机内冷水泵generator inner cooling water pump 511.离子交换器ion exchanger512.干燥器dryer, drier513.冷凝式干燥器condensing type drier514.凝汽器condenser515.多压式凝汽器multi-pressure condenser516.单流程凝汽器single-pass condenser517.双流程凝汽器double-pass condenser518.黄铜管brass tube519.管板tube plate520.凝汽器喉部condenser throat521.热水井hot well522.凝结水泵condensate pump523.泵壳pump casing524.盘根gland packing525.盘根压盖gland top cover526.盘根端盖gland end cover527.填料packing528.轴封抽汽风机shaft seal extraction fan529.轴封抽汽冷却器shaft seal extraction cooler, gland cooler530.轴封漏汽加热器shaft seal leakage heater531.低压加热器low-pressure feed water heater532.中压加热器media-pressure feed water heater533.高压加热器high-pressure feed water heater534.蒸汽冷却器steam cooler535.疏水冷却器drain water cooler536.汽侧steam side537.水侧water side538.U型管U-tube539.除氧器deaerator540.储水池water storage pond541.卧式除氧器horizontal type deaerator542.立式除氧器vertical type deaerator543.喷雾式除氧器atomizing type deaerator544.淋水盘water spraying tray, sprinkling tray545.除氧水箱deaerated water tank546.稳压水箱surge water tank, stabilizing water tank547.除盐水箱demineralized water tank548.除盐水泵demineralized water pump549.汽动给水泵steam-driven feed water pump550.电动调速给水泵motor-driven variable speed feed water pump551.前置水泵booster pump552.给水泵feed water pump553.机械密封mechanical seal554.碳精密封环carbon seal ring, carbon packing ring555.动环moving ring556.静环static ring557.平衡盘balancing disc558.液力偶合器hydraulic coupler559.泵轮（主动轮）pump impeller, driving impeller560.涡轮（从动轮）whirling impeller, driven impeller561.勺管scoop tube562.辅助油泵auxiliary oil pump563.疏水泵drain pump564.疏水扩容器drain flash tank565.疏水箱drain tank566.热网加热器heater for heating network, heating network hot water heater567.生水加热器raw water heater568.热网水泵pump for heating network, heating network hot water pump 569.生水泵raw water pump570.除尘水泵pump for scrubber, scrubber water pump571.壳体case, shell572.水室water chamber573.封头end cover574.挡板baffle plate575.导流板guide plate576.射水泵water jet pump577.真空泵vaccum pump578.射水抽气器water jet air ejector579.射汽抽气器steam jet air ejector580.射水池water jet pond581.排水池drain water pond582.工业水泵industrial water pump, service water pump583.排污泵blowdown pump584.轴流泵axial flow pump585.清水泵clean water pump586.污水泵sewage pump587.排水泵water discharge pump588.立式深井泵vertical deep-well pump589.深井泵deep-well pump590.潜水泵submerged pump591.循环水泵circulating water pump592.清污机trash remover593.混流泵mixed flow pump594.离心泵centrifugal pump595.旋转滤网rotating type screen, screw type strainer596.胶球泵rubber ball recirculating pump597.收球网ball screen598.装球网ball collector599.管式冷却器tubular cooler, tube type cooler599/1.支撑斜钢supporting wedge600.板式冷却器plate type cooler601.冷却水池cooling water pond602.喷水池spraying water pond603.冷却水塔cooling tower604.自然通风冷却塔natural draft cooling tower605.逆流式冷却塔reverse flow cooling tower606.横流式塔transverse flow cooling tower607.机力通风冷却塔mechanical draft cooling tower608.空气冷却塔air cooling tower609.干式冷却塔dry cooling tower610.分水槽water diversion channel611.竖井shaft, well612.闸板井gate well613.闸门室gate chamber, gate house614.挡风板air baffle plate615.新（主）蒸汽管道main steam piping, live steam piping 616.主蒸汽系统main steam system617.再热蒸汽系统reheat steam syetem618.抽汽系统extraction steam system619.轴封供汽系统shaft seal steam supply system620.轴封shaft seal shaft gland621.门杆漏汽系统valve lever leakage steam system622.汽缸法兰螺栓加热系统casing flange and bolt heating system 623.真空系统vaccum system624.凝结水系统condensate system625.再热蒸汽管道reheat steam system626.给水系统feed water system627.循环水系统circulating water system628.工业水系统industrial water system, service water system 629.供油系统oil supply system630.密封油系统seal oil system631.厂用蒸汽系统auxiliary steam system632.调速系统speed governing system633.电液调速系统electro-hydraulic speed governing system 634.发电机内冷水系统generator inner cooling water system 635.热网系统heating network system636.导汽管steam lead pipe637.连通管inter-connecting pipe638.抽汽管道steam extraction pipe639.抽汽母管steam extraction header640.厂用蒸汽管道plant service steam piping641.厂用蒸汽母管plant service steam header642.蒸汽旁路系统steam bypass system643.蒸汽大旁路single stage steam bypass644.一级蒸汽旁路first stage steam bypass645.二级蒸汽旁路second stage steam bypass646.辅助蒸汽母管auxiliary steam header647.供汽联箱steam header648.回汽联箱return steam header649.供水联箱water supply header650.回水联箱return water header651.门杆漏汽管道valve lever steam leakage piping652.轴封漏汽管道shaft seal leakage steam piping653.抽空气管道air extraction piping654.压缩空气管道compressed air piping655.氢气管道hydrogen piping656.疏水管道drain water piping657.凝结水管道condensate piping658.循环水管道circulating water piping659.工业水管道industrial water piping, service water piping 660.冷却水管道cooling water piping661.给水管道feed water piping662.除盐水管道demineralized water piping663.减温水管道attemperating water piping664.再循环水管道recirculating water piping665.排水管道water discharge piping666.润滑油供油管道lube oil supply piping667.润滑油管lube oil piping668.调速油管governing oil piping669.回油管道return oil piping670.压力油管道pressure oil piping671.密封油管道seal oil piping672.脉动油管pulsating oil piping673.热网水管道heating network water piping674.平衡管balance pipe675.电动主闸门motor-operated main gate valve676.高压主汽门high-pressure main stop valve677.中压主汽门intermediate pressure main stop valve 678.旁路门bypass valve679.防腐汽门corrosion-proof valve680.高压调速汽门high-pressure governor valve681.中压调速汽门medium pressure governor valve682.对空排汽门atmospheric relief valve683.疏水门drain valve684.调整门adjusting valve685.电动门motor-operated valve686.手动门hand-operated valve687.减温器attemperator, desuperheater688.减压器（阀）pressure reducer(valve)689.减温减压器temperature and pressure reducer690.抽汽电动门motor-operated steam extraction valve 691.抽汽逆止门extraction check valve692.高压排汽逆止门high-pressure exhaust check valve 693.逆止门check valve, non-return valve694.入口门inlet valve695.出口门outlet valve696.球型阀globe valve697.闸板阀gate valve698.针型阀needle valve699.翻板阀tripper valve700.液压阀hydraulic valve701.控制阀control valve702.换向阀reverse flow valve703.疏水阀drain valve704.蝶阀butterfly valve705.衬胶门rubber lined valve706.高压加热器入口联成阀composite valve at high pressure heater inlet 707.高压加热器出口联成阀composite valve at high pressure heater outlet 708.高压加热器旁路门high pressure heater bypass valve709.水封阀门water seal valve710.排污门blow down valve711.排气门exhaust steam valve712.排汽门exhaust steam valve713.补水门water supply valve, make-up water valve714.补油门oil valve, oil supply valve715.补氢门hydrogen supply valve716.空气门air valve717.真空破坏阀vacuum breaking valve, vacuum breaker718.排汽安全门exhaust steam safety valve719.弹簧安全门spring relief valve720.排汽缸喷水门exhaust cylinder water-spraying valve721.电磁阀solenoid valve, magnet valve722.前截门front intercept valve723.后截门rear intercept valve724.排氢门hydrogen vent valve725.中间抽头门intermediate stage bleed-off valve726.最小流量阀minimum flow valve727.暖泵门pump warming valve728.泵体放水门pump-body water drain valve729.放水门water discharge valve730.减温水门attemperating water valve731.切换门change-over valve, diverting valve732.联络门interconnection valve733.液压逆止门hydraulic check valve734.再沸腾加热门reboiled heating valve735.放空气门air vent valve736.再循环门recirculation valve737.冷却水门cooling water valve738.热效率thermal efficiency, heat efficiency739.内效率internal efficiency740.额定工况rated operation condition741.最大工况maximum operation condition742.汽耗量steam consumption743.汽耗率steam consumption rate744.热耗率specific heat consumption, heat rate745.新蒸汽压力initial steam pressure, live steam pressure746.再热蒸汽冷段压力cold reheated steam pressure747.再热蒸汽热段压力hot reheated steam pressure748.再热蒸汽热段温度hot reheated steam temperature749.再热蒸汽冷段温度cold reheated steam temperature750.主蒸汽流量steam flow751.再热蒸汽流量reheated steam flow752.低压缸排汽流量low-pressure cylinder exhaust steam flow753.转速rotating speed, revolution754.真空度vaccum755.旋转方向rotation direction756.给水温度feedwater temperature757.调节级压力pressure at velocity stage758.临界转速critical speed759.吊装重量lifting weight760.速度变化率speed variation rate761.迟缓率delay rate762.凸轮转角cam torque angle763.过热度superheat degree764.温差temperature difference765.端差terminal temperature difference766.过冷度supercooling degree767.高压加热器投入率high pressure heater availability rate768.轴向位移axial shift, axial displacement769.大轴晃动值shaft swinging value, shaft eccentricity770. 高压缸膨胀high-pressure cylinder expansion771.中压缸膨胀intermediate pressure cylinder expansion772.低压缸膨胀low pressure cylinder expansion773.市政速油压governing oil pressure774.润滑油压lubricating oil pressure775.脉动油压impulse oil pressure776.附加保安油压additional safeguard oil pressure777.滑阀上油压oil pressure above pilot valve778.滑阀下油压oil pressure under pilot valve779.润滑油温lubricating oil temperature780.轴承加油温度bearing return oil temperature781.轴承钨金温度babbit metal temperature, bearing metal temperature 782.推力瓦块温度thrust pad temperature783.密封油压seal oil pressure784.油位oil level785.水中含氧量oxygen content of water786.凝结水硬度condensate hardness787.轴承振动值shaft(bearing) vibration amplitude788.垂直振动值vertical vibration amplitude789.水平振动值horizontal vibration amplitude790.轴向振动值axial vibration amplitude791.油膜振荡oil film oscillation, oil whipping792.冲转impulse starting793.冷态启动cold start794.热态启动hot start795.滑参数启动starting at sliding parameters, sliding pressure starting 796.滑参数停机shut-down at sliding parameters, sliding pressure shut-down 797.升速speed up798.升速率percentage of maximum momentary speed variation,speed-up rate799.负荷上升率loading rate800.基本负荷base load801.调峰运行peak load regulating operation, cyclic operation802.空转idling, idle running803.手动打闸停机hand trip, turbine hand trip804.暖机turbine warming up805.最短盘车时间minimum turning time806.低速暖机low speed warming807.中速暖机medium speed warming808.滑参数起动曲线starting curve at sliding parameters,sliding pressure starting-up curve809.滑参数停机曲线shut-down curve at sliding parameters,sliding pressure shut-down curve810.全周进汽full admission811.部分进汽partial admission, partial-arc admission812.喷嘴调节nozzle governing813.节流调节throttle governing814.破坏真空vaccum breaking815.汽缸金属温度cylinder metal temperature816.听音检查sound detection817.惰走时间idling time818.超速试验overspeed test819.真空严密性试验vaccum leakage test820.主汽门严密性试验main steam stop valve leakage test821.危急遮断器充油试验emergency governor oil filling test822.低油压保护试验low oil pressure protection test823.调速系统静止试验governing system pre-operation test824.调速系统动态特性试验governing system dynamic performance test825.调速系统静态特性试验governing system static performance test826.甩负荷试验load-dump test, load-rejection test827.空负荷试验no-load test828.满负荷试验full-load test829.超负荷试验overload test830.转子平衡试验rotor balancing test831.动平衡dynamic balancing832.静平衡static balancing833.热力试验thermodynamic test834.叶片频率试验blade frequency test 835.投入运行to be put into operation 836.开启opening837.关闭closing838.启动starting-up839.停止shutting down840.充氢hydrogen charging841.排氢hydrogen discharging842.补水water make-up843.补油oil make-up844.水位调整water level regulation 845.暖管warming846.手摇同步器hand synchronizer847.检查inspection, examination 848.巡检routing inspection849.蒸汽带水carry-over850.水击hydraulic shock, water hammer 851.超速overspeed852.轴承损坏（烧瓦）bearing burnt-out853.断叶片broken blade854.断轴broken shaft855.气蚀cavitation856.反转（倒转）reversal rotation857.调节级regulation stage858.压力级pressure stage859.抽真空vaccum extraction860.盘车turning861.法兰加热flange heating862.螺栓加热bolt heating863.漏汽steam leakage864.漏水water leakage865.炭精轴封carbon packing866.冒烟smoking, smoke belching 867.着火fire catching, fire868.强烈振动strong vibration869.管道破裂piping breaking870.无蒸汽运行no-steam operation。
电厂常用英语词汇及缩写大全
电厂常用英语词汇及缩写大全缩写词全拼音标中文remarkSQE Supplier qualityengineer供应商质量工程师SQD Supplier QualityDevelopment供应商质量改善SQ improvement供应商质量提高QA Qualityassessment/assurance[əˈsesmənt][əˈʃʊərəns]质量评价/保证ensure[ɪn'ʃʊə(r)] Vt.保证，确保，使安全QC Quality control[kən'trəʊl] 质量控制，质量管理QI Quality improvement[ɪm'pru:vmənt]质量改进QAP Quality AssurancePlanning[əˈʃʊərəns] 质量保证计划MQAP measuement qualityassurance procedure计量质量保证方案PO Production order[prəˈdʌkʃn] 生产订单CCC China Compulsory Certification[kəmˈpʌlsəri] 中国强制认证（3C认证）compulsory [kəm'pʌls(ə)rɪ]adj. 义务的；必修的；被强制的IBR INDIAN BOILERREGULATIONS [regjʊ'leɪʃ(ə)nz]印度锅炉规程n. [管理] 条例；规程；章则BV Bureau Veritas [ˈbjuərəu][ˈveritæs]法国国际检验；法国船级社BVQI法国国际检验局Corporation Shanghai Electric Corporation缩写词Siemens AG缩写词缩写词LR缩写词INC电厂常用英语词汇及缩写大全缩写词全拼音标中文remarkNPSHR Net Positive SuctionHead Required必需汽蚀余量UNEF Unified Extra FineThread统一标准超细牙螺纹1/4-28 UNF -2BUNF unified national fine美制细牙"仙人掌GG"的文档thank you！。
火电厂英语专业词汇(汽机)
汽轮机英语词汇TURBINE VOCABULARYI Power station电站1. power station电站2. power plant电站，发电设备3. utility电力部门4.independent power producer (IPP)独立发电项目，独立发电站5.nuclear power station核电站6. thermal power station火电站7. fossil (fired) power plant化石燃料电站，常规火电站8. combined heat power (CHP) plant热电联供机组9. steam power plant蒸汽电站蒸汽发电设备10. cogeneration power station热电联供电站11. coal fired power plant燃煤电站12. oil fired power plant燃油电站13. gas filed power plant燃气电站14. LNG power plant (liquefied natural gas)燃液化天然气电站15. BoP (balance of plant)电站辅机16. I&C (instrumentation and control)仪表和控制系统II Turbine透平，涡轮17. Turbine透平，涡轮18. steam turbine汽轮机19. gas turbine燃气轮机20. nuclear turbine核电汽轮机21. fossil turbine火电汽轮机22. industrial turbine工业透平23. cogeneration turbine热电联供透平24. condensing turbine凝汽式汽轮机25. back pressure turbine背压式汽轮机26. extraction turbine抽汽式汽轮机27. extraction condensing turbine抽汽凝汽式汽轮机28. single-extraction turbine单抽汽轮机29. double-extraction turbine双抽汽轮机30. mechanical drive turbine机械驱动汽轮机31. HP (IP, LP) turbine高（中、低）压缸32.sub-critical pressure turbine亚临界汽轮机33. super-critical pressure (SC) turbine 超临界汽轮机34. ultra-super critical (USC) pressure turbine超朝临界汽轮机35. BFPT (boiler feed pump turbine)给水泵汽轮机36. steam turbine with air-cooled condenser（air cooled steam turbine）空冷汽轮机37. reheat turbine再热汽轮机38. double-reheat turbine二次再热汽轮机39. wet steam turbine湿蒸汽汽轮机40. saturated steam turbine饱和蒸汽汽轮机41. full-speed turbine全速汽轮机42. half-speed turbine半速汽轮机43. tandem compound turbine单轴汽轮机44. cross compound turbine双轴汽轮机45. super (over)-high pressure turbine过高压汽轮机46. impulse (type) turbine冲动式汽轮机47. reaction (type) turbine反动式汽轮机48. axial flow turbine轴流透平49. radial flow turbine径流透平50. turbine with axial condenser轴向排汽汽轮机51. turbine with horizontal joint带有水平中分面的汽轮机52. turbine with vertical joint带有垂直中分面的汽轮机53. double flow turbine两排汽汽轮机54. triple flow turbine三排汽汽轮机56. single-casing turbine单缸汽轮机57. double-casing turbine双缸汽轮机58. turbine proper汽轮机本体59. oil turbine 油透平60. hydraulic turbine水轮机61. marine steam turbine船用汽轮机62.aeroderivative gas turbine航改式燃气轮机63. stationary steam turbine电站汽轮机64. auxiliary turbine辅助透平III Rotary parts回转件65. rotor转子66. rigid rotor刚性转子67. flexible rotor挠性转子68. solid (forged) rotor (monobloc rotor)整锻转子69. welded rotor焊接转子70. (hollow) drum (type) rotor鼓型转子71. built-up rotor组装转子72. rotor without center bore无中心孔转子73. HP-LP integrated rotor高/低压一体化转子74. shafting (shaft)轴系75. HP (IP, LP) rotor高（中、低）压转子76. thrust collar推力盘77. journal轴颈78. section of rotor转子区段79. (first, second ) critical speed一阶（二阶）临界转速80. extension shaft (spacer)中间轴，延伸段81. coupling联轴节82. flexible coupling挠性联轴节83. rigid coupling刚性联轴节84. semi-flexible coupling半挠性联轴节85. half coupling联轴节半部86. integral (forged) coupling整体（锻制）联轴节87. shrunk-on coupling红套联轴节88. spigot（rabbet）止口89. disk (disc) 叶轮90. rim (steeple)轮缘（枞树型叶根槽）91. hub轮毂92. body（web）轮体93. T （fir tree-type ) groove T型（枞树型）叶根槽94. balance hole (plane, weight, plug)平衡孔（平衡平面，平衡配重，平衡旋塞）95. keyway键槽96. disk of constant stress (conical profile)等强度（锥形）叶轮97. disk of constant thickness等厚度叶轮98. shrunk-on disk红套叶轮99. blade叶片100. moving (rotating, rotor) blade动叶101. bucket 动叶102. straight (tapered, twisted) blade直叶片（变截面叶片，扭曲叶片）103. last stage (last but one, penultimate) blade末级叶轮（次末级叶片）104. last (locking , gate) blade (piece)末叶片（锁紧叶片，锁紧件）105. free-stand blade自由叶片106. integral shroud blade整体围带叶轮107. triple-pin blade三联叶片108. bow blade马刀型叶片109. compound lean blade复合弯扭叶片110. concave (pressure) side内弧（压力侧）111. convex (suction) side 背弧（负压侧）112. tenon铆钉头113. leading (inlet) edge 进汽边114. trailing (outlet, exit) edge出汽边115. blade wake叶片尾流116. convergent-divergent channel (CD passage)缩张通道117. brazed (stellite) shield钎焊（斯太立）防蚀片118. lacing hole拉筋孔119. profile (section of blade)叶型，型线部分（叶片截面）120. reaction（degree）反动度121. cascade叶栅122. blade root叶根123. (three teeth, straight, curved ) fir- tree (blade) root（三齿直线/弧形）枞树型叶根124. ( five finger) fork type (blade) root（五叉）插入式叶根，叉型叶根125. tee (T-type) root T型叶根126. inverted-T (blade) root倒T型叶根127. straddle-type (blade) root 外包叶根128. straddle inverted T-root 外包倒T型叶根129. dovetail root (serrated root)燕尾型（齿型）叶根130. lacing (tie) wire 拉筋131. (lacing) lug (stub) 拉筋凸台132. loose lacing wire松拉筋133. tubular lacing wire管状拉筋134. shroud (band，cover)围带135. whole circle packed (continuously connected) shroud 整圈连接围带136. integral shroud整体围带137. snubber整体围带138. gauging (throat)喉节比（喉部）139. pitch diameter节径，平均直径140. top diameter（叶片）顶部直径IV. Stationary parts静止件141. casing (cylinder)汽缸，缸体142. outer casing外缸143. inner casing内缸144. single-shell casing单层缸145. double-shell casing双层缸146. cover (upper half)上半部147. base (lower half)下半部148. horizontal (split) joint水平中分面149. (massive) flange（厚）法兰150. (casing) bore（汽缸）洼窝151.fastener (bolt, nut, stud, dowel)紧固件（螺栓、螺母、螺柱、定位销）152. vertical flange垂直法兰153. tightness气密性154. inlet进口155. exhaust排汽口156. exhaust hood 排汽缸157. guide plate导流板158. diffuser扩压管159. flange bolt hole法兰螺栓孔160. shrunk-on ring红套箍环161. combined HP-IP casing高中压合缸162. thermal shield (baffle)挡热板163. single (double) flow HP turbine单流（双流）高压缸164. flow path (steam path)通流部分165.center support system滑键系统166. lug ( foot, pawl)猫爪167. thermal insulation保温设施168. enclosure (lagging)罩壳（外壳）169. diaphragm隔板170. blade ring ( diaphragm carrier)叶片持环，隔板套171. outer (inner) ring (of diaphragm)（隔板）外环（内环，隔板体）172. stationary (stator, guide ,nozzle) blade静叶，导叶，喷嘴173. vane (partition) 静叶174. cast-in (welded-in) diaphragm铸造（焊接）隔板rotary diaphragm回转隔板175. nozzle block (chest)喷嘴组（喷嘴室）176. diaphragm deflection隔板挠度177. bearing housing (pedestal)轴承箱178. front bearing housing (standard前轴承箱179. rear bearing housing 后轴承箱180. floor(-type) bearing落地式轴承181. bearing轴承182. journal (radial) bearing支持轴承（径向轴承）183. thrust (axial) bearin推力轴承轴向轴承184. tilting pad bearing可倾瓦轴承185. Kingsburg type thrust bearing金斯布里推力轴承186. Babbitt (white metal, bearing metal)巴氏合金187. bearing bush轴承壳体188. bearing body轴承体189. bearing pad轴瓦190. bearing cover (cap) 轴承上半191. 360°bearing整圆轴承192. elliptical bearing椭圆轴承193. three wedge bearing三油楔轴承194. self-aligning bearing自找中轴承195. sleeve bearing套筒式轴承196. sliding bearing滑动轴承197. (oil) pocket (wedge)油袋（油楔）198. oil film油膜199. oil (film) whip油膜振荡200. setting pad (segment)安装瓦块201. working pad (segment)工作瓦块202. oil ring (oil deflector)挡油环203. oil film stiffness油膜刚度204. armored thermocouple铠装式热电偶V. Main Valves主要阀门205. Main (HP) stop valve (MSV)主汽阀206. control (governing) valve (CV, GV)调节阀207. reheat (IP) stop valve(RSV)再热主汽阀208. intercept valve再热调节阀209. Combined main stop/governing valve联合式主汽/调节阀210. butterfly valve蝶阀211. piloted (pre-inlet) valve预启阀212. fast valve快速动作阀213. check (non-return) valve逆止阀214. solenoid valve电磁阀215. motor driven (operated) valve电动阀216.drain valve疏水阀217. diaphragm valve (atmospheric)膜片阀（大气阀）218. relief (exhaust) valve释放阀（放汽阀）219. safety valve安全阀220. extraction valve 抽汽阀221. stop valve截止阀222. flap valve翻板阀223. gate valve闸阀224. steam chest蒸汽室225. (valve) stem阀杆226. (valve) disk (plug)阀碟227. (valve ) seat阀座228. (valve) bonnet (cover)阀帽（阀盖）229. valve casing (chest)阀壳230. (valve) travel (stroke)阀门行程231. cross over (cross under)连通管232. anti-jamming(stick) test防卡涩试验VI. Various systems各种系统(1) Control system (control and protection system)调节系统（调节保安系统）233. Electro-hydraulic control system电液调节系统234. hydro-mechanical control system液压调节系统235. DEH (digital electro-hydraulic control system)数字式电液调节系统236. electro-hydraulic converter电液转换器237. trip跳闸，脱扣238. actuator执行机构239. servomotor油动机240. pilot (slide, spool) valve滑阀241. piston活塞242. piston rod活塞杆243. (oil) cylinder油缸244. (oil) window油口（窗）245. overlap覆盖度246. emergency governor危急遮断器247. speed governor 调速器248. MSV servomotor 主汽阀油动机249. spring support操纵座250. centrifugal stop bolt撞击子251. LVDT (linear variable differential transformer)线性阀位传感器252. safety test box安全试验盒253. relay继电器，继动器254. relay valve继动滑阀255. axial displacement indicator (transducer)轴向位移指示器（传感器）256. overspeed protection超速保护257. differential expansion detector (transducer)差胀检出器（传感器）258 lever杠杆259. (cam type) steam distribution device凸轮式排汽机构260. throttle governing节流调节261. nozzle governing喷嘴调节262. partial admission (degree)部分进汽（度）263.full arc admission全周进汽264. governing (control) stage (Curtis stage) 调节级（复速级）(2) Oil system油系统265. Main oil reservoir (tank)主油箱266. turbine oil透平油267. fire-resistant fluid抗燃油268. lube (lubrication ) oil润滑油269. HP control fluid高压控制油270. pressure (feed) line (pipe)供油管道271. return (relief) line (pipe) 回油管道273.nested pipe（pipe in pipe）system套管式274. demister除油雾器275. fan风机276. mist separator 油污分离器277. oil purifier净油装置，油净化器278. oil filter滤油器279. oil cooler 冷油器280. overflow valve溢流阀281. oil vapour油雾，油气282. main oil pump( shaft driven)主油泵283. impeller（主油泵）叶轮284. switch-over (change-over)切换(3) Gland system汽封系统285. Labyrinth gland 拉别林汽封，迷宫式汽封286. gland housing (casing)汽封体287. gland segment汽封弧段288. gland (sealing) ring 汽封环289. gland strip (comb)汽封片（齿）290. brush sealing刷子汽封291. leaf sealing薄叶汽封292. diaphragm gland隔板汽封293. gland over shroud (tip gland)围带汽封294. shaft gland轴封295. gland steam condenser (cooler)汽封冷却器296. spring-back sealing回弹式汽封297. gland leak-off 漏汽298. gland ejector 汽封抽气器299. packing盘根，填函，汽封300. inner (outer) gland 内侧（外侧）汽封301. gland chamber (pocket) 汽封腔室302. dummy ring (balance piston)平衡环(4) D rain system疏水系统303. (drain) flash tank （疏水）扩容器304. drain port 疏水口305. cascade drain (system)逐级疏水306. drain cooler疏水冷却器(5) Bypass system旁路系统307. capacity容量308. HP (IP) bypass loop高压（中压）旁路回路309. start with bypass system利用旁路系统启动310. desuperheating and reducing device减温减压装置(6) Regenerative system回热系统311. HP heater高压给水加热器（高加）312. LP heater低压给水加热器（低加）deaerator除氧器313. terminal (temperature) difference (TTD) （温度）端差314. drain subcooler approach (DCA)疏水过冷段315. shell side (design pressure)壳侧（设计压力）316. tube side (design pressure)管侧（设计压力）317. condensing zone冷凝区318. drain subcooling zone疏水过冷区319. direct contact (LP) heater混合式（低压）加热器320. U tube U型管(7) Reheat system再热系统321. Cold reheat line再热冷端管道322. hot reheat line 再热热端管道323. MSR (moisture separator reheater)汽水分离再热器324. (single) reheat（一次）再热325. double reheat二次再热VII Auxiliaries辅机(1) Condenser凝汽器326. Shell-tube type heat exchanger壳管式热交换器327. surface condenser 表面式凝汽器328. direct contact condenser混合式凝汽器329. shell壳体330. (divided) water box (chamber)（对分）水室331. tube bundle管束332. tube plate (sheet) 管板333. support plate 支承隔板334. tube cleaner管子清洗器335. sponge ball cleaning system海绵球清洗系统336. double-shell condenser双壳体凝汽器337. single pass condenser单流程凝汽器338. air cooling zone空气冷却区339 air (cooled) condenser空冷凝汽器340. vacuum system真空系统341. evacuate 抽真空342. tube expander胀管器343. condensate冷凝水344. hot well (condensate sump)热井345. cooling rate冷却速率346. cleanness 清洁度347. condensate pump凝结水泵348. (condenser) neck（凝汽器）喉部349. expansion joint膨胀接头350. wave type (bellows) compensator波纹管补偿器351. deaerating capacity除氧能力352. subcooling degree过冷度353. non-condensed (condensable) gas不凝结气体354. booster pump增压泵(2) Oil cooler冷油器355. Filter过滤器strainer滤网356. cartridge滤芯357. vent通风口358. clogging堵塞359. twin-filter双联冷油器360. on－line change-over (switch-over) 在线切换(3) Ejector 抽气器361. Steam jet (air) ejector射汽抽气器362. water jet (air) ejector 射水抽气器363. (water ring) vacuum pump（水环）真空泵364. evacuation 抽真空365. vacuum establishing (forming) 建立真空366. starting ejector启动抽气器367. vacuum breaker真空破坏阀(4) Turning gear (device) or barring gear盘车装置368. Bull gear大齿轮369. driving gear驱动装置370. worm and (worm) gear涡轮蜗杆副371. turning by (every) 180°（每次）盘转180度372. jacking-up oil pump顶轴油泵373. (dis) engagement 啮合（脱开）VIII Operation运行374. Operation mode运行方式Start (up)启动375. (emergency) shut down （紧急）停机376. daily start- stop (DSS) 日启停377. initial start初次启动378. cold (state) start 冷态启动379. warm start 温态启动380. hot start 热态启动381. extreme hot start极热态启动382. base load (unit) 基荷机组383. cyclic load循环负荷384. peak load峰荷385. peak shaving调峰386. two-shift (operation)两班制（运行）387. cyclic duty capacity变负荷能力388. life cycle（使用）寿命389. life expenditure (CLE)寿命消耗390. life extension 寿命延长391. trip(ping)跳闸392. load tracking (following) capacity负荷跟踪能力393. boiler-turbine coordination control锅炉－汽机协调控制394. warming暖机395. loading-up (down)升负荷（降负荷）396. unloading甩负荷397. load throw-off甩负荷398. run up升速399. run away飞车400. idle running惰行，空负荷运行401. speed up升速402 synchronization同步403. synchronizer同步器404. connect to grid并网405. rolling (by steam)冲转（用蒸汽）406. fixed pressure (start)定压（启动）407. sliding pressure (start)滑压（启动）408. combined (hybrid) fixed/sliding pressure operation定压/滑压混合运行方式409. routine inspection日常检查410. planned maintenance计划维修411. overhaul (intervel)大修（间隔期）412. forced outage rate (FOR)强迫停机率413. repair检修414. availability可用率415. reliability可靠性416. control room 控制室417. corrosion腐蚀erosion浸蚀，水涮418. stress corrosion cracking (SCC) 应力腐蚀裂纹419. latch-on (reset)挂闸420. commission调试，试运行，交付使用。
火力发电厂常用英语词汇
火力发电站常用英语技术词汇boiler house: 锅炉房coal conveyor 输煤装置coal bunker: 煤仓coal mill磨煤机steam boiler, water boiler tube 蒸汽锅炉，管式锅炉furnace(combustion chamber): 炉膛 ( 燃烧室 )water tube: 水管ash pit 灰坑superheater: 过热器water preheater: 水预热器air preheater: 空气预热器gas duct(flue): 烟气管 , 烟道dust collecting plant: 集尘室electrical precipitation plant: 电气除尘室induced draught fan: 引风机chimney: 烟囱deaerator: 除氧器feed water tank: 供水箱boiler feed pump: 给水泵switchgear: 开关设备cable tunnel: 电缆通道cable cellar: 电缆槽turbine room: 汽轮机室steam turbine with alternator: 蒸汽汽轮发电机组 economizer: 省煤器steam drum: 汽包surface condenser: 表面凝汽low-pressure preheater: 低压预热器circulating water pipe(pump): 循环水管control room: 控制室electrostatic dustremover(precipitator): 静电除尘器pulverizer 磨煤机slag pump 灰渣泵thermal cycle: 热力循环(net)heat rate: （净）热耗率Assemblie: 集合，集结，组装comment 注释，评论module : 模块 standby: 备用proximity 相近，接近，亲近detector: 探测器 bracket: 支架interlocks 互锁，联锁 axial: 轴向的surge conditions: 喘振 : accessory: 附件 pulsation: 有节奏的跳动，跳动fossil fired: 燃煤intent: 意图，目的，意向intend: 意指，想要，打算consistent: 一致的，调和的practice: 惯例，实习，实践intrinsic: 固有的，内在的procurement 获得，获取fabrication: 制作，构成，伪造物vent: 通风孔，出烟孔，出口，放出，排出，noncondensible gas: 不凝结气体intermittent 间歇的，断断续续的blowdown : 排污 tank: 桶，箱，罐diagram: 图表 deaerator: 除氧器corrosion : 侵蚀，腐蚀状态concentration 集中，集合，浓缩，浓度recommend 推荐，介绍，托付，劝告abnormal and normal conditions: 变工况和额定工况warm up: 暖机acid wash: 酸洗scale: 范围，水垢，水锈，比例，刻度sludge :: 污泥，淤泥 foreign matter:不相关的物质 facilitate: 推动，促进，使简化multistage: 多级的remote control: 遥控safety relief valve: 安全卸压阀gauge: 量规，量表，测量manhole: 人孔，检修孔equivalent: 等价物，相等的forging:: 锻造 seat: 部位，座socket welding: 管座焊接enthalpy: 焓estimate: 评价，评估，估价parameters 参数，参量nominal : 名义上的，额定的，标称的MS — Main Steam : 主蒸汽Cycle:: 循环Intercept: 截止Fetting: 附件Gage:: 规，表，压力计Taps: 接头test wells: 测点插孔stress-relieved: 应力消除thermometer: 恒温计steam purge system: 蒸汽吹扫系统centrifugal type pumps: 离心式泵friction losses: 磨擦损失solenoid: 螺线管modulat: 调整，调节criteria: 标准wrenches: 扳手pipe taps: 管接头 .A List of Abbreviations and Symbols in English-ChineseA ::Ash Handling System: 除灰系统AH :Air Heater: 空气预热器AAh :Analyzer, Alarm High : 分析器，高值报警 :: AIV :Air Intake Valve: 进气阀ALIGN Alignment: 校正ALKF :Airlock Feeder: 锁气器AP ::Ash Slurry Pump: 灰浆泵ATM :Atmosphere 大气AC ::Air Conditioner: 空气调节器AFT :Atmosphere Flash Tank: 大气扩容器 AC :Alternating Current: 交流电ALM :Alarm:: 报警AMP :Ampere: 安培AX THR BRG :Axis Thrust Bearing: 轴向推力，轴承 ATMZ :Atomizing: 雾化AUTO :Automation 自动AUX :Auxiliary: 辅助的BA :Bottom Ash 底灰BAH ::Bottom Ash Hopper: 底灰斗BLR ::Boiler: 锅炉BSD ::Boiler Shut Down: 停炉BUSH :Bushing: 衬套BYPS :Bypass:: 旁路BVD ::Boiler Vents and Drains:: 锅炉疏水放气BFP :Boiler FeedwaterPump :: 锅炉给水泵BFPT:BoilerFeedwater Pump Turbine: 锅炉给水泵汽机 BFW ::Boiler Feedwater: 锅炉给水BM :Boiler Master 锅炉主控BMCR:Boiler Maximum ContinuousRating: 锅炉最大连续出力BFBP::Boiler Feed Booster Pump: 锅炉给水增压泵 BNR :Burner: 燃烧器BOP :Balance Of Plant: 电厂辅机设备BPC :Blade Pitch Control: 叶片节距控制 BT :Boiler Tube: 炉管CH: Crusher House: 碎煤房COMB ::Combustion 燃烧COMP ::Compressed Air: 压缩空气CONV ::Conveyer: 输送机CPL :Control Pannel Local: 就地控制盘CPM :Control Pannel Main: 主控盘CRT :Cathode Ray Tube: 阴极射线管 : CT Current Transformer: 变流器CYCL :Cyclone: 旋风分离器CAS :Casing:: 缸、壳CB Circuit Breaker: 断路器COMP :Complete: 完成CCCW :Closed Circulating Cooling Water: 闭式循环冷却水CCW :Cycle Cooling Water: 循环水CCWHF ::Closed Cooling Water Heater 闭式冷却水冷却器CCWP :ClosedCooling WaterPump: 闭式冷却水泵CS :Closed Cooling Water System 闭式冷却水系统 CH Coal Handling 煤的装卸CHK VLV :Check Valve: 逆止阀CIRC: Circulation: 循环CLR Cooler: 冷却器CLOW :Cooling Water: 冷却水CMPR :Compressor: 压缩机CNTL :Control: 控制CNTLE :Controller:: 控制器COND :Condensate: 凝结水CONDTY :Conductivity: 导电率CP: Condensate Pump: 凝结泵CIR: Circuit: 回路COUPI :Coupling: 联轴器CP: Condensate Polisher: 除盐装置CS: Control Switch 控制开关CRSV :Cold Reheat Safety Valve: 再热器冷段安全阀 CV: Control Valve :控制阀CWP: Circulation Water Pump: 循环水泵DMPR: Damper : 挡板DP Difference Pressure: 差压DPIC: Differential PressureIndicating Controller压差指示控制器DPT: Differential PressureTransmitter 压差变送器 DRN: Drain:疏水DV Drain Valve:: 疏水阀DC Direct Current: 直流电DSH: Desuperheater: 减温器DCA: Drain Cooler Approach: 疏水冷却器通道 DEAER Deaerator: 除氧器DEV: Deviation: 偏差DIFFRLY: Differential Relay: 差动继电器DISCH VLV :Discharge Valve 排放阀DIST: Disturbance:: 故障、扰动DSCH: Discharge: 排出ECON: Economizer:: 省煤器EP Electrical Static Precipitator: 静电除尘器ECC Eccentricity :: 偏心EFF Efficiency: 效率EHC Electric Hydraulic Control: 电液控制EO Electric Operate: 电气操作EQ Equipment: 设备ER Error: 误差ES :Extraction System 抽气系统ESC Escape: 逃逸、超出ESS Engineering Safety System: 保安系统EU Engineering Unit : 工程单位EXH Exhaust: 排汽EXT Extract: 抽出FA :Fine Ash: 细灰FDR Feeder: 给料机FE :Flow Element:: 流量元件FI :Flow Indicator:: 流量指示件FDBK: Feedback: 反馈FITG Fitting: 连接件FLW Flow 流量FO :Fail Open: 故障时自动打开FT: Flow Totalizer: 流量累加器FT :Flow transmitter: 流量变送器FV :Flow Control Valve 流量控制阀FY :Flow Relay or Valve 流量传送器FA: Failure Alarm: 故障报警FD :Forced Draft : 强制通风FDF Forced Draft Fan: 送风机FIC :Flow Indicate Controller: 流量指示控制器 FLT :Flash Tank : 扩容箱FLD :Field 磁场FLG :Flange: 法兰FLM Flame: 火焰FWH Feed Water Heater 给水加热器FO :Fuel Oil: 燃油FREQ Frequency: 频率FURN Furnace: 炉膛GLD Gland: 密封GRDR Grinder: 碎渣机GND Grounding: 接地GC :Generator Cooling: 发电机冷却GESE Gland Steam Condenser Exhauster: 轴加风机GMT Generator Main Trandformer: 发电机变压器GRAD Grandient: 梯度GS :Gland Steam: 轴封蒸汽GSC :Gland Steam Condenser: 轴封加热器 GV :Governor Valve: 高压调门H ::Heat Conservation 保温HS: Hand Switch:: 手动开关HTR Heater: 加热器HV: Hand Control Valve: 手动控制器HY: Hand Relay or Transducer 手动继电器（转换器） H :Hand: 手动的HB :Heat Balance: 热平衡HD :Heater Drain:: 加热器疏水HDR :Header: 联箱HL ::Heat Loss: 热损失HMDY Humidity: 湿度HPH: High Pressure Heater: 高压加热器HPR :Hooper: 漏斗HPT :High Pressure Turbine: 高压汽机HR: Hot Reheat: 再热器热段HR: Heat Rate: 热耗率HSV: Hot Reheat Safety Valve: 再热器热段安全阀HVAC :HeatingVentilation & Air Conditioning::暖通 HW :Hotwell: 热井HV ::Hand Control Valve: 手动控制器HYD :Hydraulic: 液力的INTLK :Interlock : 联锁IC :Instrument and Control:: 仪表与控制（热工）ICV ::Inrtermediate Control Valve 中压控制阀ID :Induced Draft 抽风，引风IDF ::Induced Draft Fan: 引风机IGN ::Ignition: 点火装置INLT :Inlet: 入口IPR ::Initial Pressure: 初压INST :Instrument: 仪表INVR :Inverter: 逆变器I /O:: Input/Output 输入 / 输出IP :Intermediate Pressure: 中压ISV ::Intermediate Pressure Turbine Steam Valve: 中压缸进汽阀 JP :Jet Pump: 喷射器LG :Level Gauge 液位计LVL ::Level: 水位，液位LA :Level Alarm: 液位报警LIM(LMIR): Limiter: 限制器LKG:: Leakage:: 泄漏LP :Low Pressure 低压:Low Point : 低位LPH: Low Pressure Heater: 低压加热器LSH: Local Switch Hand: 就地开关LUB: Lubricating Oil: 润滑油M :Mechanical: 机械M :Motor: 马达MAG:: Magnetic: : 磁性MOD ::Mode: 方式 :M/A :Manual/Automatic: 手动 / 自动MAN ::Manual :: 手动MARG: Margin:: 裕量MAX ::Maximum: 最大的，最大值的MCR ::Maximum Continuous Rating 最大连续出力 MCV:: Main Control Valve:主控制阀MD :Modulation Damper: 调节挡板MDBFP: Motor Driven Boiler FeedwaterPump: 电动给水泵 MEAS ::Measure :测量MFT: Master Fuel Trip: 主燃料跳闸MIN :Minimum: 最小的MKUP (MU) Make-up: 补充ML :Mill: 磨煤机MN :Main: 主要的. :Manual Operation: 手操MPT :Main Power Transformer: 主变压器MS :Main Steam 主蒸汽MSV :Main Steam Valve: 主汽阀NOZ: Nozzle: 喷嘴NPSH :Net Pump Suction Head: 泵的静吸压头OL: Overload: 过载OLR :Overload Relay: 过载继电器OPER :Operation: 运行OSC :Oscillograph: 示波器OTLT: Outlet: 出口PA: Primary Air: 一次风PAF :Primary Air Fan: 一次风机PAH :Pressure Alarm High: 高压报警PAL :Pressure Alarm Low: 低压报警PB: Push Button 按钮PC :Power Centre: 动力中心PC: Pressure Controller: 压力控制器. :Pressure Control: 压力控制PCP :Precipitator 除尘器PCV :Pressure Control Valve:: 压力控制阀PDI :Pressure DifferentialIndication: 差压指示 PDT :PressureDifferential Trandsmitter: 差压变送器 PED :Pdestal:: 轴承座PERF CALC Performance Calculation::性能计算 PF: Power Factor 功率因数PHTR: Preheater: 预热器PMP :Pump: 泵PNEU :Pneumatic: 气动的PR: Pressure Recorder: 压力记录计PRG :Purge: 吹扫PRV :Pressure Relief Valve: 泄压阀PRO :Protection: 保护PROGR:: Program: 程序PT: Pressure Transmitter: 压力变送器PULV: Pulverizer: 磨煤机PVSV :Pressure Vacuum Safety Valve压力真空安全阀 PW: Plant Water 厂用水PY: Pressure Relay: 压力继电器QA: Quality:: 质量，性能RB: Run Back: 快速降负荷RCV :Recovering: 回收RECIRC:: Recirculation 再循环RECT :Rectifier: 整流器RET :Return: 返回RH: Reheater: 再热器RO: Restriction Orifice: 节流孔板ROT :Rotor: 转子RTU :Remote Telemetry Unit:: 遥测装置 SA :Secondary Air: 二次风SAT: Saturate: 饱和的SC :Steam Coil Air Heater:: 暖风器SCAV :Scavenge: 吹扫SD: Shut-off Damper: 关断挡板 : Shut-Down 停机SEP :Separator 分离器SG: Switchgear 开关装置SH: Superheater: 过热器SLS :Seals:: 密封SO: Shut Off: 关闭SPD :Speed: 转速SPRA: Spray: 喷水SPT :Support: 支持 :ST: Start: 启动，开始STD-BY :Stand By: 备用ST: System:: 系统STM :Steam: 蒸汽STR: Stator:: 定子STRNR: Strainer: 滤器SU: Start Up: 启动SV: Solenoid Valve: 电磁阀SUCT: Suction: 吸入SW: Switch: 开关 :Steam Water: 汽水SBLWR: Soot Blower 吹灰器TBFP Turbine Drive Boiler FeedwaterPump 汽泵 TCV :Temperature ControlValve 温度控制.: Transfer Damper: 转换挡板TE: Temperature Element: 温度元件TG: Turbine-generator: 汽轮发电机Turbine-gear: Turbine-gear: 汽机盘车 THERM :Thermal 热力的TMS: Turbine Master System: 汽机主控系统 TRANS :Transfer: 转换TRBL: Trouble: 故障TRKG: Tracking: 跟踪TT: Temperature Transmitter: 温度变送器TTD: Terminal Temperature Difference: 温度端差TW: Thermowell: 热电偶套管UAM :Unit Automatic Master: 机组自动系统VAC: Vacuum: 真空VAL: Value: 数值VB: Vibration 振动 VLV: Valve: 阀门WH: Watthour 瓦小时WP: Working Point: 工作点WW: Water Wall 水冷壁WX: Watt Transducer: 功率转换器COVER :Crossover 切换管CV: Control Valve: 控制阀英汉对照表A/H ： AUTOMATION/HAND : 自动 / 手动 ;A/M ： AUTOMATION/MANUAL: 自动 / 手动 ;ALARM 报警 ;AUX ： AUXILIARY :: 辅助 ;BYPASS 旁路CLOSE 关（状态，常指阀门） ;CODE: 代码；编码COLD START — UP: 冷态启动COMPUTER : 计算机CURVE ， LINE: 曲线，线DATA: 数据；文件；资料DECREAS : 减少DESK: 台，桌DIGIT: 数字DISK: 磁盘DYNAMIC ； DYNAMICAL: 动态F ： FLOW 流量 ;FAST: 快FIGURE: 图示HIGH: 高HOT START — UP: 热态启动I＆C ：INSTRUMENT AND CONTROL 仪表与控制INCREAS: 增加INDICATION ； DISPLAY : 指示；显示 ; INLET 入口 ;INPUT 输入 ;INTERMEDIATE 中KEYBOARD: 键盘KW ： KILOWATT 千瓦L ： LOAD 负荷，负载 ;LOC ： LOCAL : 就地LOW: 低MCS ：MANAGMENT COMMAND SYSTEM 管理命令系统MODE : 方式，模式MW ： MEGAWATT 兆瓦NORMAL: 正常OFF : 关（状态） ;ON : 开（状态） ;OPEN: 开 ( 状态，常指阀门 );OPERATE : 运行；操作 ;OUTLET 出口 ;OUTPUT 输出 ;P ： PRESSURE: 压力 ;PANEL 盘PARAMETER : 参数PIPE ； TUBE: 管道，管子PLANT: 厂，站POWER: 功率，电源 ;PRINT: 打印R ： RATE : 比率，速率 ;R ： RESISTANCE: 电阻 ;REM ： REMOTE : 摇控 ;RESET 复位ROOM : 室RPM:: 转 / 分 ;S ： SPEED 速度 ;SELECT 选择SET POINT 设定点SHUTDOWN : 停机 ;SIDE （某）侧，边 ;SILENCER 消音器SLOW : 慢STAND BY: 备用 ;START : 启动 ;STARTUP : 起动；启动 ;STATIC 静态STATION 站STOP: 停止 ;SYMBOL 符号SYSTEM: 系统T ： TEMPERATURE:: 温度 ; TEST: 试验 ;TRANSMITTIER;TRANSDUCER: 变送器；传感器TRIP 跳闸 ;TRIP ACKNOW: 跳闸确认UNAVAIL 不允许 ( 不能投用的 ) UNIT : 单元、机组VALVE 阀门WARM START — UP: 温态启动ZOOM: 摄像机镜头锅炉部分ACTUAL MEGAWATT: 有功AIR DRAFT SEQUENCE: : 风机程序控制（顺控）AIR HEATER A MOTER: 空预器马达 AAIR HEATER LOC/REM SELECT: 空预器就地 / 遥控选择AIR HEATER MOTOR LEAD: 空预器马达选择AIR HTR A SEC AIR OUT TEM 空预器 A 二次风出口温度AIR PREHEATER: 空预器AIR SVCE SUPPLY: 服务空气ALARM LIMITS: :: 报警限制ALL AIR HTRS RUNNING 各空预器运行ALL PULV GRP SHUTDOWN 所有磨组停运ASH — HOPPER: : 灰斗ATTEMPERATOR: : 减温器AUX .ST: SPLY FOR ATOMIZ 辅助蒸汽供雾化蒸汽BOIL MILL A BNR MET TEMP 炉 A 磨组喷燃器金属温度BOIL MILL A GR1 WDBOX PR 炉 A 磨组第一组风箱压力BOILER AIR REQUIRED 锅炉风量需求（ >30% ）BOILER EFFLUENT STORAGE: POOL 锅炉废水池BOILER FOLLOW MODE: 炉跟随方式BOILER MASTER: 锅炉主控器BOILER TRIP RESET: : 锅炉跳闸复位BOILER: 锅炉BURNNER: : 燃烧器CHIMNEY ； STACK:: : 烟囱CLEAN: 清扫COAL BANKER: :: 煤仓COAL FEEDER : 给煤机COMBUSTION : 燃烧CONVEYOR: 皮带机COORDINATE MODE 协调方式CRUSHER: 破碎机DECR/INCR PRESS AT FIX LOAD:: 固定负荷方式增减压力DOWM COMER:: 下降管DRAIN & VENT: 疏水和排气ECONOMIZER : 省煤器EITHER FAN RUNNING : 任一风机运行EITHER ID FAN RUNNING 任一吸风机运行ELECTROSTATIC PRECIPITATOR : 静电除尘器FD FAN A FLOW:: A 送风机流量FD FAN/ID FAN A CONT DAMPER A 送 / 吸风机控制挡板FEED WATER FLOW: 给水流量FEEDER LOCAL SELECT: 给煤机就地控制选择FEEDER REMOTE SELECT: 给煤机遥控选择FLUE GAS: 烟气FORCED DRAFT FAN : 送风机FUEL GAS ID FAN A OUTLET PRESS A 吸风机出口压力FURNACE PRESS: 炉膛压力FURNACE: 炉膛GAS COAL: :: 烟煤HEADER : 联箱、母管IGNITOR: : 点火器，油枪INDUCED DRAFT FAN : 引风机INDUCED&FORCED DRAFTS: 吸送风机INITIATE: 启动、引燃、激发、触发ISOLATION: 隔离；绝缘LFO .DISCH .PRESS : 轻油出口压力LIGHT OIL SEL GRP 1: 第一组轻油枪选择LIGHT OIL: 轻油LUB OIL PUMP:: 润滑油泵MAIN STEAM STOP VLV: 主蒸汽截止阀MAIN STEAM TEMP/PRESSURE/FLOW 主汽温度 / 压力 / 流量MAINTAINED IGNITORS PULVERIZER A:磨煤机A油枪操作MANUAL LOAD SET/RATE:手动负荷设定 / 负荷率MANUAL MODE: 手动方式MANUAL THROTTEL PRESS SET POINT:手动节流压力设定值MILL A GROUP MASTER : A 磨组主控器MILL A LOAD: A 磨组负荷MILL A OUT TEMP CONT DAMPER : A 磨组出口温度控制挡板MIN MAX LOAD （ LIMITS ） : 最大最小负荷（限制）MMMC ＝MILLIMETER MERCURY ；MMH2O: 毫米汞柱；毫米水柱O 2 IN THE FUEL GAS 烟气含氧量OPEN/CLOSE SWING VLVS 摆阀开 / 关OPERATE MODE SELECT: 运行方式选择PENDANT: : 悬吊管PLATEN SPARY CONTROL VLVS SIDE A : 屏过减温水 A 侧控制阀PLATEN SUPERHEATER: 屏过PRESSURE DIFFERENCE: 压差PRI AIR DUCT PRESS 一次风管压力PRI AIR FAN A CONT DAMPER: A 侧一次风机控制挡板PRI AIR FAN A OUTLET PRESS A 一次风机出口压力PRI AIR FLOW MILL A CONT DAMPER 磨组一次风控制挡板PRI/SEC AIR FLOW MILL A A 磨组一次 /二次风流量PRIMARY AIR FAN: 一次风机PRIMARY AIR SEQUENCE: 一次风控制PULVERIZER : 磨煤机PULVERIZER EMERGENCE TRIP 磨煤机紧急跳闸PULVERIZER INERT MODE SELECT: 磨煤机惰性方式选择PULVERIZER NORMAL MODE SELECT: 磨煤机正常方式选择PULVERIZER SELECTION A :: 磨煤机 A 选择PULVERIZER: M/A: SELECT 磨煤机手 / 自动选择PURGE 吹扫RH ； REHEATER: 再热器SAFETY VALVE:: 安全阀SCANNER BLOWERS: 火检吹扫器SEAL AIR FAN PRESS: 密封风机压力SEAL AIR FAN:: : 密封风机SEC AIR DUCT PRESS: 二次风管压力SEC AIR FLOW MILL A CONT DAMPER A 磨组二次风流量控制挡板SEC SH OUT STEAM TEM 二级过热器出口蒸汽温度SEC SH SPARY CONT VLVS SIDE A 二级过热器减温水 A 侧控制阀SECONDARY SH INLET TEMP 二级过热器进口温度SECONDARY: AIR 二次风SH ； SUPERHEATER: : 过热器SH STEAM ELECTR VLV: 过热器电磁阀SH STEAM TEMP SET POINT:: 过热温度设定点SH/RH SPARY WATER STOP VLVS:: 过热器 / 再热器减温水截止阀SH/RH SPRAY CONTROL VLVS SELECT 过热器 / 再热器减温水控制阀选择SLIDING PRESS MODE: 滑压运行方式SOOT BLOWER: 吹灰器SPARK 火花，点火花SPEED CHANGE (NOT) PERMISSIVE: 速度切换（不）允许SPRAY : 喷水STACKER RECLAIMER :: 堆取料机START IGNITOR GRP 1: 第一组油枪点火STEAM DRUM: : 汽包STEAM 蒸汽STONE COAL: 无烟煤STOP IGNITORS GRP 1: 第一组油枪停止STOP/START FEEDER 给煤机停止 / 启动STOP/START IGNITORS: 油枪停止 / 启动STOP/START MILL: 磨组停止 / 启动STOP/START PA FLOW: 一次风停止 / 启动STOP/START PULVERIZER 磨煤机停止/ 启动STOP/START SEQUENCE PULVERIZER A: 磨煤机 A 程序停止 / 启动THROTTLE PRESS:: 节流压力TRANSPORT AIR SEQUENCE 风量程序控制（顺控）TURB FIRST STAGE PRESS 汽机第一级( 调节级 ) 压力TURBINE FOLLOW MODE: 机跟随方式TURBINE MASTER: 汽机主控器TWIN FLOW AIR HTR A CONT VLV: : 双流式空预器控制阀UNLOADER: :: 卸煤机WATER 水WATERWALL: : 水冷壁汽机部分:EMERG OIL PUMP: 事故油泵<P>CICR PMP DISCHARGE VLV: 循环泵出口阀1ST STAGE PRESS: 第一级压力ACTUAL MEGA WATT: : 实际负荷数AMS ： ADMISSION: MODE SELECTION 进汽方式选择AUX STEAM HEADER: : 辅汽联箱AUX STEAM TEMP CONTROL: 辅汽温度控制AUX STM HEADER PRESS CONTROL VLV 辅汽联箱压力控制阀BALANCE: : 平衡BEARING BRASS:: 轴瓦BEARING: : 轴承BLADE 叶片BOILER FOLLOW MODE: 锅炉跟随方式BOOSTER FEED PUMP: 前置给水泵CICR WTR PUMP: 循环泵CIRCULATING PUMP: : 循环泵CIRCULATING: 循环CLOSED COOLING WATER: 闭式冷却水CLOSED COOLING WTR PUMP: 闭式冷却水泵CMPTR: : 计数器CONDENSATE PUMP: 凝泵CONDENSER AIR SUCTION VLV: 凝汽器抽空气阀CONDENSER HOT WELL: : 热井CONDENSER LEVEL CONTROL VLV: 凝汽器水位控制阀CONDENSER: 凝汽器CONDS EXTR PUMP DISCH : 凝结水抽吸泵出口CONDS STOR TANK LEVEL: 凝结水储水箱水位COOLER: : 冷却器COOLNG WTR PUMP: 水冷泵COORDINATE MODE: : 协调方式CV ： CONTROL VALVE 高压调门CYLINDER 、 CASING: 汽缸DEAERATOR LEVEL CONTROL VLV: 除氧器水位控制阀DEAERATOR: : 除氧器DECR PRESS AT FIX LOAD: 在负荷不变下减压DEMI WATER: 除盐水DISPATCH PARTICIPATION 调度（参与）指令DURM PRESSURE:: 汽包压力EJECTOR: 喷射器，抽气器EMERGENCY GOVERNOR 危急保安器EXHAUST: 排汽EXPANSION: 膨胀EXTR ST TO HP HTR 抽汽至高加EXTRACTION STEAM 抽汽FILTER: : 滤网FLANGE 法兰FUNCTION GROUP: 功能组FW CONTROL VALVE ' S BYPASS VLV: 给水控制阀的旁路阀FW FLOW 30% CONTROL VLV : 30% 给水控制阀FW FLOW MASTER CONTROL: 给水流量主控FW HP HTR DISCH TEMP: 给水高加出口温度FW PUMP RECIRCUL CONTROL VLV 给水泵循环控制阀FW VLV: 给水阀门GEARING: 盘车GOVERNOR: 调速器HP ATTEM PRESS CONTROL VLV: 高旁减温水压力控制阀HP ATTEMP BLOCK VLV: 高旁减温水闭锁阀HP BYPASS ＆ HP ATTEMP VLVS: 高压旁路及减温水阀HP BYPASS PRESS CONTROL VLV 高旁压力控制阀HP BYPASS PRESS SET POINT: 高旁压力设定值HP BYPASS TEMP CONTROL VALVE 高旁温度控制阀HP＆LP BYPASS COMMAND 高压及低压旁路指令HPH ： HIGH PRESSURE HEATER : 高加HYDRAULIC OIL STATION PUMP: 液压油站泵INCR PRESS AT FIX LOAD: 在负荷不变下增压INT POS: 中间状态IV ： INTERMEDIATE VALVE 中压联合汽门JACKING OIL PUMP 顶轴油泵LP HTR STOP VLV 低加截止阀LP ＆ HP BYPASS PRESS SIDE A 低压或高压旁路A侧压力LP ＆ HP BYPASS TEMP SIDE A 低压或高压旁路A侧温度LPH ： LOW PRESSURE HEATER: 低加LUBE OIL PUMP: 润滑油泵MAKE － UP WATER: 补给水MANUAL LOAD RATE 手动负荷率MANUAL LOAD SET 手动负荷设定MANUAL Throttle Press Set Point手动节流压力设定值MEASURE SELECTION 测量选择站MOP ： MAIN OIL PUMP: 主油泵MOTOR DRIVEN FEED WATER PUMP 电动给水泵MSV ： MAIN STOP VALVE: 主汽阀NOZZLE 喷嘴OIL PURIFIER: 净油器OIL STORAGE TANK : 储油箱OPERATE MANUAL MODE: 手动方式OPERATE MODE SELECT: 运行方式选择PILOT VALVE: 错油门PLATEN SH INLET TEMP SIDE A: A侧屏过入口温度PRIMARY SH STOP VALVE: 一级过热器截止阀PUMP A DISCH PRESS : A 泵出口压力RH SPRAY BLOCK VLVSTRIP INIT 再热器喷水闭锁阀跳闸启动RH SPRAY WTR STOP VLVS: 再热器喷水截止阀RH STEAM ATTEM FLOW: 再热喷水流量RH STEAM TEMP OUTLET: 再热器出口温度ROTOR 转子SEAL: 密封SHAFT 轴SILENCER: 消音器SLIDING PRESS MODE: 滑压方式SPEED INDICATOR OR SPEED METER: : 转速表STATOR 定子STEAM TURBINE : 汽轮机ST － UP BOIL FDW PUMP: 启动给水泵SUCTION PUMP: 抽吸泵SURGE APPROACH: 喘振SYNCHRONIZER: 同步器TFW PMP DISCHARGE VLV: 汽动泵出口阀TFW PUMP MAIN OIL PMP: 汽动给水泵的主油泵THROTTLE ORIFICE 节流孔板TURBINE DRIVEN FEED WATER PUMP: 汽动给水泵TURBINE FW PUMP AUX ＆ VLV 小机给水泵辅汽及阀门TURBINE GENERATOR: 汽轮发电机组TURBINE INLET PRESS: 汽机入口压力TURBINE MASTER : 汽机主控器TURBING FOLLOW MODE: 汽机跟随方式VACCUM 真空VACUUM BROKEN VALVE: 真空破坏门VACUUM SEQ : 真空程控VIBRATION: 振动电液调节及控制部分1STAGE PRESSURE FEEDBACK: 第一级压力反馈ABNORMAL CONDITION: 异常状态ACCELERATION: 加速度ACTIVE POWER:: 有功功率ADMISSION MODE: 进汽方式ADS(ALARM DISPLAY SELECT PANELS) 报警显示选择屏AERIAL LINE: 架空线ALTERNATING CURRENT (AC): 交流AMPERE: 安培ANGLE OF LAG: 滞后角ANGLE OF LEAD: 超前角ANODE: 阳极ARC: 电弧ARMATURE 电枢AST ： AUTO SHUT-DOWN TRIP: 自动停机遮断ASYNCHRONOUS MOTOR: 异步电动机AT SET SPEED: 在设定速度位置ATC ： AUTO TURBINE CONTROL: 自动汽轮机控制AUTOFORMER: 自藕变AUTORECLOSING : 自动重合闸AUXI TRANSFORMER : 厂用变BACK UP TRANSFORMER 备用变BACK-UP OVERSPEED TRIP TEST 备用超速跳闸试验ELECTRICAL TRIP TEST电气跳闸试验BACK-UP SPDSIG LOST: : 后备速度信号失去BARRING OIL PUMP 盘车油泵BASE LOAD: 基荷BATTERY : 电池BATTERY BACKED CLOCK 电池备用时钟BDV ： BLOWDOWN VLV: 泄放阀BOOSTER PUMP: 前置泵BULB : : 灯泡BUS SECTION : 母线分段BUS: 母线BUSBAR FRAME: 母线架BUSCOUPLER: 母联BUSHING 套管CABLE 电缆CAPACITANCE: 电容CARRIER 载波CATHODE : 阴极CCR: 中控室CHARGING EQUIPMENT : 充电设备CHEST /ROTOR WARMING: 腔室 / 转子预暖CIU : 计算机接口单元CLOSE : 合闸CLOSED VALVES OVERSPEED TEST 关闭阀超速CLOSED-LOOP : 闭环COIL:: 线圈COMBINED RECLOSING 综合重合闸COMBINED REHEAT VALVES: 中压联合阀COMMON SERVICES LOGIC SUITE:: 公用系统逻辑柜COMMUNICATION: 通讯CONDUCTOR : 导体CONFIGURATION: 结构，布置，外形 :CONTROL OIL: 控制油CORE: 铁芯CPU(CENTARL PROCESSING UNIT: 中心处理单元CRT: 显示屏CURRENT TRANSFORMER: 电流互感器CURRENT 电流CV:: 控制阀DAS: 数据采集系统DECREASING LOAD RATE: : 减负荷率DIESEL GENERATOR : 柴油发电机DIRECT CURRENT (DC) 直流DISCONNECTOR : 隔离开关DISTRIBUTED CONTROL SYSTEM: 分散控制系统工程师工作站EHC STATUS: 电液调节系统状态EHC ： ELECTRO-HYDRA CONTROL SYSTEM:电液调节控制系统EHV MIMIC PANEL : 电气高压模拟屏ELECTRICAL MALFUNCTION SYSTEM FAULT :电气失灵系统故障EMERGENCY OIL PUMP: 事故油泵EMERGENCY SEAL OIL PUMP: 事故密封油泵ETS ： EMERGENCY TRIP SYSTEM: 危急跳闸系统EXCEPTION REPORT: 例外报告EXCITE 励磁EXCITOR 励磁机FA/PA POSITION : 全周 / 部分（进汽）位置FAST-ACTING SOLENOID: 快动电磁阀FIRST STAGE PRESS 调节级压力FIS :: 流量显示开关FREQUENCY: 频率FRF ： FIRE RESISTANT FLUID:: 抗燃油FULL ARC : 全周进汽GAS : 瓦斯GEN. SHAFT SEAL&STATOR WIND : 发电机密封及静子绕组GENERATOR : 发电机GROUNDING(EARTHING) 接地H2 TEMP CONT V : 氢气温度控制阀HARDWARE 硬件HOLD: 保持HYDRAULIC FLUID PRESS: 抗燃油压力数字控制站终端模件IN STANDBY: 在备用状态IND: :: 指示器INDUCTANCE: 电感INHIBITED: 停止进行、禁止INSULATOR 绝缘子INTERCEPT VALVE: 中间截流阀INTERCEPT VALVES: 中间截止阀INTERFACE 接口KILOWATT 千瓦LC: 液位控制器LI: 液位显示LIGHT: 照明LINE 线路LK: 液位控制站LOAD DECREASING ； AT SET LOAD 负荷减；在设定负荷LOAD FLOW : 负荷潮流分布LOAD INCREASING: 负荷增LOAD LIMITING SET: 负荷极限设定LOAD MONITORING: 负荷监视LOAD SELECT: :: 负荷选择LOAD SET: 负荷设定LOAD: 负荷LOADING RATE LIMIT : 负荷（增、减）率限定LOCKED OUT: 闭锁LOSS : 损耗LOSS OF PWR:: 失去电源LVDT ：线性位移差动变送器MAGNETIC FIELD: 磁场MAIN OIL PUMP: 主油泵MAIN SEAL OIL PMP : 主密封油泵MAIN STEAM PRESS 主蒸汽压力MAIN TRANSFORMER STEP-UP TRANSFORMER:主变MANUAL: 手动MCC: 马达控制中心MEGAWATT: 兆瓦MFP : 多功能控制器MOTOR: 电动机MSPL ： MAIN STEAM PRESSURE LIMITER :主汽压力限制器MSV: 主蒸汽阀NEUTRAL POINT: 中性点OHM: 欧姆OIL GAUGE: 油位表OPC ： OVERSPEED PROTECTION CONTROL:超速保护控制OPEN-LOOP : 开环OPER AUTO: 操作员自动 ::OPERATING MODE : 操作方式ORP ： OIL RESET PISTON: 油复位活塞ORSV ： OIL RESET SOLENOID VLV 油复位电磁阀OTSV ： OIL TRIP SOLENOID VLV: 油跳闸电磁阀OVER CURRENT: 过流OVER VOLTAGE : 过压OVERLOAD: 过载PART ARC : 部分进汽PC: 动力中心PDIS : 压差显示开关PEAK LOAD: 峰荷PERMANENT MAGNETIC GENERATORDF 永磁发电机PG: 压力计PHASE ANGLE : 相角PHASE: 相PIC: 压力显示控制器PK: 压力控制站PLUG : 插头PLUG SOCKET: 插座POLE:: 电极POTENTIAL TRANSFORMER 电压互感器POWER 功率POWER FACTOR: 功率因数POWER LOAD UNBALANCE: 功载不平衡PP ： : PREESSURE POINT 压力检测点PRI SPD SIG LOST 一次速度信号失去PS: 压力开关PT: 压力变送器REACTANCE: 电抗REACTIVE POWER: 无功功率RECLOSING : 重合闸REHEAT PRESS:: 再热汽压力REMOTE AUTO: 远方自动REMOTE OPERATION : 远操RESISTANCE: 电阻RSM ： ROTOR STRESS MONITORING: 转子热应力监视 :RSV: 再热汽截止阀SAFELY OIL : 安全油SCR CONTROLLER: 可控硅整流控制器SEAL OIL: 密封油SHUT-OFF VALVE:: 切断阀SIGNAL: 信号SLOW MEDIUM FAST: 慢、中、快SPEED INCREASING: 速度增SPEED MONITORING: 速度监视SPEED SET RPM : 转速设定转 / 分SPEED: 速度，转速START UP TRANSFORMER 启动变STATOR WIND COOLING WATER PUMP: 定子绕组冷却水泵STEAM SEAL BY-PASS UNLOAD VLV: 蒸汽密封旁路泄放阀STEAM SEAL DIVERING VALV: 密封汽分流阀STEAM SEAL SYS:: 蒸汽密封系统SUCTION PMP A/M SEL: 抽吸泵手 / 自动选择SUCTION PUMP: 抽吸泵SUPERVISORS DESK: 值长台SWITCH 开关SWITCHGEAR : : 配电盘、开关装置TELEPHONE: 电话TEST SELECT: 试验选择（联锁）THERMO-COUPLE: : 热电偶THREE ELEMENTS LEVEL CONTROLLER: 三冲量水位控制器THRUST BEARING WEAR DETECTOR TEST 推力轴承磨擦检测试验TI : 温度显示器TIC :: 温度指示控制TIME DELAY: 时间延迟TP: 温度检测点TRANSFER AND FILTER PUMP: 输送和过滤油TRANSFORMER: 变压器TRANSMISSION: 传输TRIP 跳闸TS: 温度开关TSI: 汽机监视仪表TT:: 温度变送器TURB LUBE OIL TEMP CONTROL V : 汽机润滑油温度控制阀TURBIN DRAIN VALVES: 汽机疏水阀TURBINE LATCHED: 汽机挂闸TURN GEAR CONTROL SEQUENCE 盘车控制程序TURN GEAR MOTOR: 盘车主电机TURN GEAR PIGGY: BACK MOTOR 盘车啮合电机UNINTERRUPTED POWER SUPPLY: 不间断电源UNIT CONTROL DESK: 机组控制台UNIT TRANSFORMER:: 单元变VACUUM TRIP: 真空跳闸VALVE POSITION: 阀位置VI : 阀位置指示VOLT(V): 伏特VOLTAGE 电压VT: 阀位置变送器VV ： VENTILATING VALVE : 通风阀WARMING RATE: 暖机速率WATT: 瓦特WINDING: 绕组。
火电厂必备电力英语词汇.
电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)通用部分（General Parts）--1--of程师协程师协--2--brake制动器、刹车--3-- back-up each other相互备用--4----5----6----7--电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)通用部分（General Parts）--8----9----10--通用部分（General Parts）--11--电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)汽轮机（Turbine Island）跟踪汽轮机（Turbine Island）water hammer水击relief valve 溢流阀风箱点火器,油枪空气档板油枪仿真机天然气点火, 火花烟煤空侧烟侧绝缘,保温T 形管三通的飞灰电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)锅炉（Boiler Island）抽头压力快速启动额定的保护干温充电高压电网电线保险丝电动机相电位三段三相跳闸线圈合闸线圈联锁蓄电池组电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)电气（Electric Island）电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)电气（Electric Island）伏特表电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)电气（Electric Island）rheostat变阻器plant network厂用电系统ADS (auto dispatching system)自动调度系统gross power总功率turn匝outage停电key switch按键开关interrupter断路器service life使用寿命LED (light emitting diode)发光二极管dispatcher调度员arc电弧magnitude幅值，大小eddy current涡流--26--电力英语词汇(ENGLISH VOCABULARY FOR ELECTRIC POWER)热工（Instruments and Controls）--27--接点脱机操作编译程序子回路number of input points 输入点resolution 分辩率SCADA (supervisory control and dataacquisition) 监控和数据采集operation guide 操作指导peripheral equipment 外围设备pneumatic local controller气动就地控制器preamplifier 前置放大器post-trip report 跳闸后报告printout 打印输出PI (proportional-integral) 比例—积分--33--滤网湿度压力温度当量石棉硬度海绵味道水库，水neutralization passivant 中和钝化剂--37—201、 方格纸；网格纸 grid paper 202、 方通 square tube 203、 方块图 block diagram 204、 方锉 square file205、 方头钻嘴 square shank bit 206、 方螺帽 square nut207、 方边凿；直边凿 firmer chisel 208、 木 wood 209、 木工 woodwork210、 木工工作间 woodwork area 211、 木工工作台 woodworker ’s bench212、 木工车床 wood turning lathe; woodworking lathe213、 木工铅笔 carpenter ’s pencil 214、 木工刨床 thicknessing and planning machine 215、 木牙螺丝；木螺钉 wood screw 216、 木材 timber217、 木材车削 wood turning218、 木材车削工具 wood turning tools 219、 木屑压合板；万花板 chipboard 220、 木条接榫 corner strip joint 221、 木圆头槌 doming mallet 222、 木模；模型 patterns 223、 木线 wood strip224、 木胶粉 ureaformal dehyde resin glue225、 木锉 rasp 226、 木螺钉；木牙螺丝 wood screw 227、 木槌 mallet228、 止推轴承 thrust bearing 229、 止推垫圈 thrust washer 230、 比例 proportion 231、 比例尺 scale232、 比例常数 proportionality constant 233、 比例极限 proportional limit 234、 比较器 comparator235、 比热容量 specific heat capacity 236、 水平投影面 horizontal plane 237、 水平仪；平水尺 spirit level 238、 水气掣；漏电断路掣 earth leakage circuit breaker (ELCB)239、 水晶胶；聚酯树脂 polyester resin 240、 水晶胶的铸造成形 resin casting 241、 水磨砂纸 silicon carbide paper 242、 火叉 firing fork 243、 火水；煤油 kerosene244、 火牛；变压器 transformer245、 火石轮 grinder 246、 火花电蚀法；放电极加工 electrical discharge machining 247、 火酒；工业酒精 methylated spirit 248、 火钳 tongs 249、 火线；活线 live wire250、 火砖 fire brick251、 爪扣；爪形离合器；犬齿式离合器 dog clutch252、 牙板；丝模 die 253、 牙板扳手；丝模扳手 die holder (stock) 254、 牙板螺帽 die nuts 255、 牛皮胶；动物胶 animal glue256、 牛油纸 tracing paper257、 牛顿运动定律 Newton ’s laws of motion258、 犬齿式离合器；爪扣；爪形离合器 dog clutch259、 丙烯?丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 260、 主轴；心轴 spindle261、 主题 motif 262、 令(纸张的计数单位) ream263、 凹座 recess 264、 凹模 hollowing block265、 凸缘 flange 266、 凸缘联轴节 flange coupling267、 凸轮 cam 268、 凸轮式配件 cam-action fitting269、 凸轮传动 cam drive270、 凸头螺丝 raised headscrew271、 加成作业；添加法addition process272、 加油 oiling 273、 加速器 accelerator 274、 功能；用途 function 275、 功率因子power factor276、 功率放大器 poweramplifier 277、 功率板 power amplifier board278、 功率晶体管 powertransistor 279、 包氏记号法 Bow ’s notation 280、 「包浩思」；「包豪斯」〈设计风格) Bauhaus 281、 半永固法；半永久接合 semi-permanent joining 282、 半接榫 halving joint283、 半闭式槽榫 stopped housing joint 284、 半圆(木)锉 half-round rasp 285、 半圆车刀 turning gouge286、 半圆锉 half-round file 287、 半圆头铆钉 snap rivet288、 半导体 semiconductor 289、 卡路里；卡(热量单位) calorie 290、 卡纸 card paper291、 卡尺；测径器 calipers 292、 去角；倒角 chamfer293、 可切削性 machinability 294、 可行性 feasibility295、 可逆过程 reversible process296、 可压缩性 compressibility 297、 可变电阻 variable resistor298、 四分仪 quadrant299、 四爪夹头 four-jaw independent chuck 300、 四圆心法(绘图) four-centre method本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25551.html301、 外卡尺 outside calipers 302、 外形塑造 shaping 303、 外形线；轮廓线 outline304、 外推法 extrapolation305、 外圆弯凿 firmer gouge 306、 外螺纹 external thread 307、 外螺纹制造法 threading 308、 外弯边 convex edge309、 外观 appearance310、 失真 distortion 311、 尼龙；聚醯胺 nylon; polyamide (PA) 312、 尼龙墨水针笔 technical felt-tip pen313、 左右调校杆 lateral adjusting level 314、 市售尺寸；标准尺寸 stock size315、 市电频率；电源频率 mains frequency 316、 平(木)锉 flat rasp 317、 平水尺；水平仪 spirit level318、 平行投影 parallel projection 319、 平行车削 parallel turning 320、 平行虎钳 parallel vice 321、 平行钉法 parallel nailing322、 平底弯刨 flat faced spokeshave 323、 平底钻嘴 forstner bit324、 平板结构 slab construction325、 平流扼流圈；滤波扼流器 smoothing choke 326、 平流电容器；滤波电容器 smoothing capacitor327、 平流电路；滤 本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25550.html 401、 印刷电路板 printed circuit board (PCB)402、 同素异形 allotropy 403、 同轴电缆 coaxial cable 404、 同温 equality of temperature 405、 向量；矢量 vector 406、 向量和 vector sum 407、 合力 resultant force 408、 合口扁钳 close mouth tongs 409、 合成色；等和色 secondary colour 410、 合成品 composite 411、 合成本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25549.html501、 坑凿 cross-cut chisel 502、 均方根值 root mean square value 503、 均角投影图；等角投影图 isometric drawing504、 均速圆周运动 uniform circular motion505、 夹；夹钳 clamp 506、 夹 cramp507、 夹卡 mounting board 508、 夹具 fixture; jig509、 夹具及固定装置 jig and fixture 510、 夹板；胶合板 plywood 511、 夹持工具 clamping device; holding tool512、 夹背锯；榫锯 tenon saw 513、 夹头 chuck514、 夹头开启匙；夹头扳手 chuck key515、 夹叠黏合成形 lamination 516、 尾座 tailstock 517、 床身；床道 lathe bed 518、 床鞍；刀座帷 apron 519、 形心；面心 centroid 520、 形状 shape 521、 形变 deformation 522、 「快把」板；硬质纤维板 hardboard523、 快速移位 rapid traverse 524、 抗扭强度 torsional strength 525、 抗屈强度 bending strength; yieldstrength526、 抗性分量；无功分量 reactive component 527、 抗拉强度 tensile strength528、 抗氧化剂 anti-oxidant529、 抗剪强度 shearing strength530、 抗磁性物料 diamagnetic material 531、 抗挠性 stiffness 532、 抗压强度 compressive strength 533、 抗断强度 breaking strength 534、 技术员；技师technician 535、 扶架 steady 536、 扭力 torsion 537、 扭矩；转矩 torque538、 扭转 torsion 539、 扭转角 angle of torsion540、 把手 hand grip 541、 扼流圈 choke 542、 扳手 spanner; wrench543、 投影 projection 544、 投影面 projection plane 545、 投影线 projection line546、 攻丝 tap 547、 材料 material 548、 材料单；材料表 material list 549、 杜拉铝 duralumin 550、 杉木 spruce 551、 步进电动机 stepper motor552、 步冲轮廓法 nibbling 553、 每分钟转数 revolution per minute (r.p.m.) 554、 系统组件 systemcomponent 555、 角托架 angle bracket556、 角位移angular displacem ent557、 角板；直角板 angle plate558、 角度 angle 559、 角榫 corner angle joint; corner joint560、 角铁 angle iron561、 谷巴凡立水 cobalvarnish562、 车刀架 tool holder563、 车床 lathe 564、 车床工具lathe tools 565、 车床中心钻咀 lathe centre bit 566、 车床操作法 lathe operation 567、 车削；车旋 lathe turning; turning 568、 车削工具 turning tools 569、 防火胶板 Formica 570、 防锈 rust prevention571、 防声耳筒；护耳器 ear-protector572、 防松螺帽 lock nut573、 防护装置；保护罩；保护网 guard; safety guard574、 注射成形法；喷射铸造法 injection moulding 575、 并激电动机；并绕电动机 shunt-wound motor576、 乳酪胶 casein glue 577、 乳胶漆 emulsion paint 578、 亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)579、 亚稳态的；介稳态的 metastable 580、 来回摆动 oscillating 581、 两点透视 two-point perspective 582、 刻度；划线 ruling 583、 刺冲 dot punch 584、 刮刀 scraper585、 刮擦 scraping 586、 制动鼓 drum brake 587、 制动碟 disc brake 588、 制动器 brake589、 受迫振动 forced vibration 590、 受迫振荡 forced oscillation 591、 和谐 harmony592、 周转齿轮；行星齿轮 epicyclic gear 593、 固定夹；台夹 bench holdfast594、 固定负载 dead load 595、 定子 stator596、 定位销；合钉 dowel 597、 定位螺丝 set screw 598、 定距轮 stitch marker599、 屈片机 folding machine 600、 屈曲 bending 本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25548.html601、 屈服点；降服点 yield point 602、 屈圈法 loop forming 603、 屈卷法 scrolling604、 屈接缝 folded lap seam605、 屈喉机 tube bender 606、 屈折 folding607、 屈折线 folding line608、 屈压接缝 folded & grooved seam 609、 延性 ductility610、延性的ductile611、弦锯法plain sawing612、弧口凿；圆凿gouge613、往复式运动reciprocatory motion 614、拉力tensile force615、拉力计；张力计tensiometer; tensometer616、拉钉blind rivet; pop rivet617、拉钉接合blind riveting; pop riveting618、拉钉钳blind riveting pliers; pop riveting pliers619、拉张tension620、拉张应力tensile stress621、拉张应变tensile strain622、拉细drawing-down623、拉制法drawing624、拉线wire drawing625、「披」口；利口；铁屑burr 626、拔钳nippers本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25547.html701、长方通rectangular tube702、长刨trying plane703、长螺旋钻咀long auger bit 704、长镗孔long boring705、闸极gate706、阻抗impedance707、附件attachment708、附录appendices709、青铜bronze710、非反相放大器non-inverting amplifier711、非本征半导体extrinsic semiconductor712、非破坏性试验non-destructive testing713、非晶状固体amorphous solid 714、非顽磁性铁磁材料non-retentive ferromagnetic material715、非压缩性流体incompressible fluid716、非稳态unsteady state717、非铁金属；不含铁金属non-ferrous metal 718、九画719、亮漆；力架lacquer720、信号signal721、信号产生机signal generator722、信号处理signalprocessing723、保养；维修maintenance724、保险丝fuse725、保护罩；保护网；防护装置guard;safety guard726、促凝剂accelerator727、削屑swarf728、垂直投影面vertical plane729、型砧swages730、〈书的〉封皮binding731、封面cover732、急回机构quickreturn mechanism733、扁枝bar734、扁头cross-pein735、扁头法upsetting736、扁头铆钉flathead rivet737、扁头螺丝flathead screw738、扁凿flat chisel739、指示器indicator740、指形榫fingerjoint741、施力effort742、染色staining743、染色剂stain744、架构framework745、柄stock746、柚木teak747、柳安木lauan748、流程图flow chart749、洗漆水paintremover750、活塞piston751、活塞销gudgeonpin752、活线；火线live wire753、炮铜gunmetal754、玻璃砂纸glasspaper755、玻璃胶siliconsealant756、玻璃纤维glass fibre757、玻璃纤维席glass fibremats758、界面；分界面；接口interface759、相差phasedifference760、相对密度relativedensity761、砂布emerycloth762、砂磨sanding763、砂磨纸abrasivepaper764、砂磨机sander765、砂铸；砂铸模sand casting766、研究探讨research767、研磨；磨削grinding768、研磨角grinding angle769、科技technology770、科技研习technological studies771、科学知识scientific knowledge772、科学瓷；聚氰胺毋醛树脂melamine-formaldehyde resin (MF)773、红铜垫圈copper washer774、美学aesthetics775、耐火胶板fire-resisted laminate776、耐火砖refractory block777、耐冲击聚苯乙烯high impact polystyrene778、背back779、胡桃木walnut780、范德华引力Van der Waals force781、英制惠氏标准螺纹British Standard Whitworth thread (B.S.W.)782、苯乙烯丙烯?共聚物styrene-acrylonitrile copolymer783、苯酚甲醛phenol formaldehyde (PF)784、计；规gauge785、定时器timer786、计划planning787、计算器；计算机computer788、计算器辅助工程computer-aided engineering (CAE)789、计算器辅助控制computer-aided control790、计算器辅助设计computer-aided design (CAD)791、计算器辅助制造computer-aided manufacturing (CAM)792、计算器数控computer numerical control (CNC)793、负反馈；负回输negative feedback794、负极；阴极cathode795、负载load796、轨路式砂纸磨机orbital sander797、重力；引力gravitational force798、重心centre of gravity799、重量weight800、重锉法heavy filing本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25546.html801、限制开关；极限掣limit switch802、限流器current restrictor803、降服点；屈服点yield point804、降压器step down transformer805、面plane806、面心；形心centroid807、面材plane materiel808、面板face plate809、面板车削法face plate turning810、面结型晶体管junction transistor811、面罩face mask812、音量volume813、页边margin814、风车锯；圆盘锯circular saw 815、风格style816、风煤炉forging hearth817、飞轮flywheel818、飞机木；菠萨轻木balsa819、首版；原型；雏形prototype 820、恒温器；温度调节器thermostat 821、俯视图；平面图plan822、倒角；去角chamfer823、倒模成形；模塑；铸模成形moulding824、修边trimming825、修边机trimmer826、剖切面cutting plane827、剖切面线cutting plane line 828、剖面；纵切面section829、剖视图sectional view830、剖线hatching line831、刚性；刚度rigidity832、刚性模量；刚性模数modulus of rigidity833、刚强度；硬挺度stiffness834、刚体rigid body835、原子粒；晶体管transistor 836、原色primary colour837、原型；雏形；首版prototype 838、原料raw material839、哥罗芳；三氯甲烷chloroform 840、埋头直孔counterbore841、埋头铆钉countersink head rivet 842、埋头锥孔countersink843、埋头螺栓countersink head bolt 844、埋头螺丝countersink head screw 845、埋头钻countersink drill846、埋头钻嘴countersink bit; rose countersink drill847、套筒；套管sleeve848、套锤fullers849、家用的domestic850、展性malleability851、展性的malleable852、展开图development853、峰至峰值peak-to-peak value 854、峰值peak value855、差动放大器；微分放大器differential amplifier856、徒手草图freehand sketch857、径线锯法radialsawing858、径锯法quartersawing859、振动vibration860、振幅amplitude861、振荡oscillating862、振荡运动oscillatory motion863、振荡器oscillator864、效率efficiency865、时效硬化agehardening866、时间常数timeconstant867、框架frame868、气动的系统；气压的系统pneumaticsystem869、气动控制pneumatic control870、气阀gas valve871、气焊gas welding872、空气压缩aircompression873、氧乙炔焊接oxy-acetylene welding874、氧化oxidation;oxidize875、消失点vanishingpoint876、消色差achromatic colour877、浸涂dip coating878、海绵状塑料；泡沫塑料；多孔塑料foamplastics879、浮力buoyancy880、浮雕relief881、特性property882、珠光体pearlite883、疲劳fatigue884、真空成形；真空吸塑vacuum forming885、真空成形机vacuumformer886、真空吸塑成形法vacuummoulding887、真实形状true shape888、矩波形rectangularwaveform889、纹理grain890、级联系统cascadesystem891、纸板cartonboard892、脆弱的；易碎的brittle893、脆性brittleness894、脉冲pulse895、能量守恒conservation ofenergy896、能量守恒定律law ofconservation ofenergy897、草图sketch898、草图画纸layout paper899、草稿draft900、衰减attenuation本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25545.html901、起化magnetization902、起泡剂；发泡剂foaming agent903、起动扭矩starting torque904、起动器starter905、起磁；磁化magnetization906、退化degradation907、退火annealing908、配件fitting909、钉合nailing910、钉钳；铁钳pincers911、钉冲nail punch912、钉锤cross-pein hammer913、针尖point914、针叶needle-point leaf915、针叶树coniferous tree916、针锉；杂锦锉needle files917、马氏体martensite918、马达；电动机；摩打motor919、马粪纸straw board920、骨架结构carcase construction921、容差；宽裕度allowance922、高密度聚乙烯high density polyethylene (HDPE)923、高通滤波器high-pass filter924、高速钢high speed steel925、高电压high voltage926、高碳钢high carbon steel927、干燥法；干材法seasoning928、偶合；耦合(电工) coupling929、侧面投影side projection930、侧条芯夹板laminboard931、侧视图；端视图end elevation; end view932、偏心凸轮eccentric cam933、偏向bias; deviation934、偏差deviation935、偏压bias936、偏离drift937、剪刀scissors938、剪力shearing force939、剪切shear940、剪床；闸床guillotine941、对角剪钳diagonal cutting pliers942、动力工具power tool943、动力学dynamics944、动物胶；牛皮胶animal glue 945、动圈式电流计moving coil galvanometer946、动态；运动movement947、动态平衡dynamic equilibrium 948、动摩擦dynamic friction; kinetic friction949、匙孔锯key-hole saw; pad saw 950、只读存贮器；只读存储器read only memory (ROM)951、国际标准组织The International Standard Organization (ISO)952、基本设计原理design fundamentals953、基极电流base current954、基准边true edge955、基尔霍夫定律；克希何夫定律Kirchhoff’s Law956、密度density957、常规conventions958、带式砂磨机belt sander959、带式传动belt drive960、带通滤波器band-pass filter 961、带锯；运锯band-saw962、张力计；拉力计tensiometer; tensometer963、强化reinforcement964、强化塑料reinforced plastics 965、彩度chroma966、控制系统control system 967、卷尺flexible rule; tape rule 968、接口；界面；分界面interface 969、接合joining970、接合工具joining tool971、接地earthing972、接缝lapped seam; seam973、接触角angle of contact974、扫上光油varnishing975、推拔车削taper turning976、推进器propeller977、斜切车刀skew turning chisel 978、斜投影oblique projection 979、斜角mitre980、斜角；斜面bevel981、斜角规bevel; sliding bevel 982、斜角榫mitre joint983、斜身螺丝攻taper tap984、斜格纸；等角投影纸isometric grid paper985、〈织物的〉斜纹bias986、斜钉法dovetailnailing987、斜率gradient988、斜视图obliquedrawing989、斜榫尺mitresquare990、斜榫规mitregauge991、斜槽位；鱼尾槽位dovetail trench992、斜边凿beveledged chisel993、旋扭法twisting994、旋钮；球形把手knob995、旋制法spinning996、旋转；转动rotation997、旋转台rotatingplatform998、旋转轴rotatingshaft999、旋转运动rotarymotion1000、杆；枝rod本文来自: 恒星英语学习网()详细出处参考：/word/kyyy/2008-02-18/25544.html1001、条线图；棒形图bar chart1002、梨形凸轮pear-shaped cam1003、液相liquidphase1004、液晶体显示liquid crystal display(LCD)1005、液压liquidcompression1006、液压控制hydraulic control1007、液压机hydraulicpress1008、添加法；加成作业additionprocess1009、添加剂additive1010、清漆varnish1011、清胶gelresin1012、混合胶；二合胶epoxy glue1013、深拉制法deepdrawing1014、深度计；深度规depthgauge1015、淬火quench1016、淬火液quenchingliquid1017、淬硬quenchhardening1018、焊接welding1019、焊枪brazingtorch1020、焊剂flux1021、焊炉brazing hearth1022、球形把手；旋钮knob1023、球体sphere1024、瓷釉；搪瓷；珐琅enamel1025、瓷漆；磁漆enamel paint1026、产品设计规格product design specification (PDS)1027、眼罩goggles1028、硫化作用vulcanization1029、移印字dry rub on transfers1030、第一角投影法first angle projection1031、第三角投影法third angle projection1032、符号symbol1033、粗削roughing1034、粗纹bastard cut1035、粗刨jack plane1036、统一〈设计〉unity1037、组件component; module1038、组合角尺combination square1039、组合钳combination pliers1040、组合图；装配图assembly drawing1041、汇编语言；汇编语言assembly language1042、组合逻辑combinational logic1043、组成物料component material1044、组织原理(设计) organisation1045、脱碳decarburization1046、脱模剂release agent1047、脱模腊mould release wax1048、茎stem1049、蛋形木槌bossing mallet1050、规；计gauge1051、规身stock1052、规柄stem1053、规格specification1054、许可应力permissible stress1055、设计design1056、设计元素design element1057、设计作业；专题设计研习design project1058、设计师designer1059、设计记录档案design folder1060、设计组织design organization1061、设计处境；设计环境design situation1062、设计规格design specification1063、设计提案design proposal1064、设计程序design process1065、设计概要；设计纲要design brief1066、设计解决方法design solution1067、贯穿鸠尾榫through dovetail joint1068、软木softwood1069、软板；绝缘板soft board 1070、软胶；聚乙烯polyethylene (PE) 1071、软焊soft soldering1072、软焊料soft solder1073、软钢mild steel1074、通用面板universal surface plate 1075、连接杆；连杆linkage1076、连结板web1077、连续插图sequential drawing 1078、速度velocity1079、速度比velocity ratio1080、造形form1081、造型砂moulding sand1082、透明；通透transparent 1083、透视投影perspective projection 1084、透视法perspective1085、透视图perspective drawing 1086、闭孔；盲孔；不贯穿孔blind hole1087、闭合电路closed circuit1088、死循环控制closed-loop control 1089、死循环控制系统closed control system1090、死循环增益close loop gain 1091、阴极；负极cathode1092、陶瓷ceramics1093、陶瓷制品ceramic product 1094、顶尖centre1095、顶面投影top projection 1096、顶脱销ejector pin1097、鱼尾半接榫dovetailed tee halving joint1098、鱼尾榫；鸠尾榫；燕尾榫dovetail joint1099、鱼尾槽位；斜槽位dovetail trench1100、麻花钻twist drill本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-18/25543.html1201、评估evaluation1202、评鉴criticism1203、象限quadrant1204、超塑料superplastic 1205、超载overload1206、超声波ultrasonic wave1207、超声波测试ultrasonic test1208、轴shaft1209、轴心车削法turning between centres1210、轴功shaft work1211、轴承bearing1212、轴接coupling1213、轴环；卡圈collar1214、周期period1215、进料螺杆feedscrew1216、进给feed1217、进给速率feedrate1218、进给螺杆feedscrew1219、量角器protractor1220、量度measurement1221、量度工具measuring tool1222、钝blunt1223、开口式槽榫through housing joint1224、开口扁钳openmouth tongs1225、开口销cotterpin1226、开孔凿holepunch1227、开材方法(木材)conversion1228、开环控制系统open-loop control system1229、阳极；正极anode1230、阳极氧化法；阳极处理anodizing1231、集成电路integrated circuit (IC)1232、集电极电流collector current1233、云尺；云板；曲线规Frenchcurve1234、云母mica1235、韧皮部bast1236、韧性toughness1237、顺磁性paramagneticmaterial1238、黄金分割goldensection1239、黄金比例goldenratio1240、黄铜brass1241、黑皮软钢black mildsteel1242、传动系统drivesystem1243、传动螺杆drivescrew1244、传意技巧；表达技巧communicationtechnique1245、传感器；换能器；转能器transducer1246、传热性conductivity of heat1247、传导conduction1248、传导性conductivity1249、倾角angle of inclination; rake angle1250、倾斜面inclined plane1251、势能；位能potential energy1252、势梯度；位梯度potential gradient1253、汇编语言；汇编语言assembly language1254、圆口夹钳round tongs1255、圆形及椭圆形尺circle and ellipse guide1256、圆形凸轮circular cam1257、圆形开口牙板circular split die1258、圆咀钳round nose pliers1259、圆底弯刨round faced spokeshave1260、圆弧运动circular motion1261、圆枝round rod1262、圆规compasses1263、圆通；圆管round tube1264、圆折边beaded edge1265、圆盘锯；风车锯circular saw1266、圆锉round file1267、圆头弧刀round nose gouge1268、圆头铆钉conical head rivet; round head rivet1269、圆头螺丝round head screw1270、圆头铁锤ball pein hammer; raising hammer1271、圆瓣图pie chart1272、圆铁砧bick iron1273、圆凿；弧口凿gouge1274、塞子plug1275、塞状螺丝攻plug tap1276、塑性plasticity1277、塑性形变plastic deformation1278、塑料plastics1279、塑料土；橡皮泥plasticine1280、塑料涂层plastic coating1281、塑料层积片；层叠塑料片laminated plastic sheet1282、涂料；油漆paint1283、涂层金属片coated metal sheet1284、塔轮cone pulley1285、填角焊接fillet weld1286、填料；填剂filler1287、奥氏体austenite1288、微分放大器；差动放大器differential amplifier1289、微电子学microelectronics1290、微调fine-adjustment1291、溜板座；刀座鞍saddle1292、详细图；零件详图details drawing1293、意念；构想idea1294、感温开关temperature sensitive switch1295、感应电路sensor circuit1296、感应器sensor1297、搪瓷；珐琅；瓷釉enamel 1298、搪瓷炉；釉窑enamelling kiln 1299、搭接；叠榫lap joint1300、搭焊lap welding本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-17/25493.html1301、搜集资料；数据搜集data collection1302、摇摆钉法staggered nailing 1303、摇摆运动oscillating motion 1304、暗接斜角鸠尾榫secret mitre dovetail joint1305、暖色warm colour1306、楔；劈尖wedge1307、楔槽榫barefaced tongue and groove joint1308、楔铁drift1309、极限制limit switch1310、极限张应力ultimate tensile stress1311、杨氏模量Young modulus 1312、榆木elm1313、沟刨plough plane1314、温度梯度temperature gradient 1315、温度调节器；恒温器thermostat 1316、温差电偶thermocouple 1317、温标temperature scale1318、滑枕ram1319、滑动件slider1320、滑块曲柄机构slider crank mechanism1321、滑刨；光刨smoothing plane 1322、滑轮pulley1323、煤油；火水kerosene1324、炼制合金alloying1325、炼钢炉steel furnace1326、照明lighting1327、碎屑；切屑chip1328、碎料板；刨花板particle board 1329、硼砂borax1330、万用尺multi-purpose rule 1331、万用电表multimeter1332、万向接头universal joint1333、万向轴节universal coupling1334、万能胶contactglue1335、节奏；韵律rhythm1336、节约能源conservation of energy1337、经干木材seasoned timber1338、脚掣footbrake1339、脑力激荡法brainstorming1340、葫芦夹钳pick-up tongs1341、蜂鸣器buzzer1342、装拆式结构knock-down construction1343、装拆扣件knock-down fitting1344、装订binding1345、装配图；组合图assembly drawing1346、装饰的图案或式样motif1347、解决方法solution1348、解决问题problem solving1349、译码；译码decode1350、试验testing1351、跳菲；小型电路断路器miniature circuitbreaker (MCB)1352、载电live1353、运动motion1354、运动的控制control of motion1355、运动的传送transmission of motion1356、运动的转化conversion of motion1357、运动学kinematics1358、运算放大器operational amplifier1359、运锯；带锯band-saw1360、达底螺丝攻bottomingtap1361、釉窑；搪瓷炉enamellingkiln1362、钳pliers1363、铅lead1364、铅笔pencil1365、铅笔刨pencilsharpener1366、刨plane1367、刨刀cuttingblade;plane iron1368、刨夹capiron1369、刨床shapingmachine1370、刨底sole1371、刨削shaping1372、刨削刀具shaping tool1373、刨楔level cap1374、铆钉rivet1375、铆钉接合riveted joint1376、铆钉模rivet set & snap1377、铆接riveting1378、闸床；剪床guillotine1379、隔离器isolator1380、电electricity1381、电力分线箱distribution board1382、电子束焊接electron beam welding1383、电子零件electronic component1384、电子零件接驳wiring1385、电子管valve1386、电子学electronics1387、电木Bakelite1388、电玉；醛树脂ureaformaldehyde (UF)1389、电池cell1390、电池组battery1391、电位；电势electric potential1392、电位计potentiometer1393、电位差potential difference1394、电抗reactance1395、电弧焊electric arc welding1396、电阻抗impedance1397、电阻值resistance1398、电阻率resistivity1399、电阻温度计resistance thermometer1400、电阻器resistor本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-17/25492.html1401、电流current1402、电流表；安培计ammeter1403、电流放大器current amplifier1404、电流增益current gain1405、电容率；介电常数permittivity1406、电容量capacitance1407、电容器capacitor1408、电烙套件soldering kit1409、电烙铁electric soldering iron1410、电动势electromotive force1411、电动机；马达；摩打motor1412、电荷charge; electric charge1413、电势；电位electric potential1414、电感器inductor1415、电极electrode1416、电源开关switch1417、电源频率；市电频率mains frequency1418、计算机；计算器computer 1419、计算机辅助工程computer-aided engineering (CAE)1420、计算机辅助控制computer-aided control1421、计算机辅助设计computer-aided design (CAD)1422、计算机辅助制造computer-aided manufacturing (CAM)1423、计算机辅助设计与制造系统CAD/CAM system1424、计算机数控computer numerical control (CNC)1425、计算机数控车床CNC lathe 1426、电路circuit1427、电磁线圈；筒形线圈；螺线管solenoid1428、电枢；衔铁线圈armature 1429、电线electric wire1430、电线退皮钳wire stripper 1431、电导率electrical conductivity 1432、电导量conductance1433、电压voltage1434、电压比voltage ratio1435、电压比较器voltage comparator 1436、电压放大voltage amplification 1437、电压放大器voltage amplifier 1438、电压表voltmeter1439、电压降voltage drop1440、电压调节器voltage regulator 1441、电镀electroplating1442、电钻electric drill1443、零件；组件component1444、零件分散图；爆炸图exploded drawing (view)1445、零件表parts list1446、零件详图；详细图details drawing1447、零件图parts drawing1448、零位校正zero correction 1449、顽磁性铁磁材料retentive ferromagnetic material1450、饱和度saturation1451、鸠尾榫；鱼尾榫；燕尾榫dovetail joint1452、鸠尾榫锯dovetail saw 1453、鼓式制动器drum brake1454、鼓风炉blastfurnace1455、划针scriber1456、划线layout;marking out; ruling1457、划线刀markingknife1458、划线工具marking tool1459、划线规markinggauge; surface gauge1460、划线轮stitchmarker1461、图形表达技巧graphic presentationtechnique1462、图案；花样pattern1463、图框drawingframe1464、图画的阴暗部shade1465、图画纸cartridgepaper1466、图象传意graphical communication1467、图头钉Frenchnail1468、垫片；垫圈；介子gasket; washer1469、垫板；台垫bench hook1470、垫料backing1471、实践计划realization1472、对比contrast1473、对流convection1474、对接butt1475、对接合；对接榫butt joint1476、对接角榫buttmitred joint1477、对接焊buttwelding1478、对称symmetry1479、惯性力矩；转动惯量moment ofinertia1480、惯性负载inertiaload1481、截锥铆钉pan headrivet1482、折尺foldingrule1483、折床；弯曲机bendingmachine1484、折铁砧hatchetstake1485、折铁器folding bar1486、敲打成形beatening1487、杠杆lever1488、构件member1489、构成作业fabricationprocess1490、构架接合；构架榫framedjoint1491、构架结构frameconstruction1492、构想；意念idea1493、榫头tenon1494、榫眼；卯孔mortise1495、榫规；双线规mortise gauge1496、榫锯；夹背锯tenon saw1497、榫凿mortise chisel1498、槌击法chopping1499、演绎技术(设计) rendering technique1500、滚子轴承roller bearing本文来自: 恒星英语学习网() 详细出处参考：/word/kyyy/2008-02-17/25491.html1501、滚花身；压花身knurled shank1502、滚珠轴承ball bearing1503、滚纹；切辊纹knurling1504、滚动摩擦rolling friction1505、滚压；辘压rolling1506、漏电断路掣；水气掣earth leakage circuit breaker (ELCB)1507、滞后现象hysteresis1508、渗碳cementation1509、熔化fusion1510、熔渣slag1511、熔焊接fusion welding1512、磁化；起磁magnetization1513、磁化电流magnetizing current1514、磁性magnetic property1515、磁场magnetic field1516、磁场强度magnetic field strength1517、磁漆；瓷漆enamel paint1518、磁铁magnet1519、碟式制动器disc brake1520、碟式离合器；盘式离合器plate clutch1521、碟形凹陷法sinking1522、碳化三铁体cementite1523、碳化合金carbide1524、碳钢carbon steel1525、端面车削facing1526、端纹end grain1527、端视图；侧视图end view1528、管pipe1529、综合synthesis1530、网格grids1531、网格纸；方格纸grid paper1532、网络；网络network；web1533、维修；保养maintenance1534、聚乙烯；软胶polyethylene (PE)1535、聚丙烯；百折胶；百折胶polypropylene (PP)1536、聚四氟乙烯polytetrafluoroethylene (PTFE)。
火电厂英语专业词汇
第3页 共9页
Cooling fin coordination system(CCS) core coupling crack/cracking creep critical pressure CT :current transformer cubical cylinder cylindrical D.C. resistance deaerator（D.A） decimal demineralized water density diaphragm dielectric digit display digit signal dimension diode
辅助的 轴向的 备用 条形 条形图 成组的、成批的 波特率 隔间 轴承座 轴瓦 二进制的 二进制单元 二进制计数器 比特、位 烟煤 毛胚 熔断 吹扫 排污管 沸腾 锅炉 煮炉 开断电流 褐煤 汽泡 燃烧器 总线接口模块 母线 电缆 检验 电容 电容电流 电容器 容量 碳 树脂浇注变压器 锻造 中心线 集控室 通道、信道
common service system compatibility compatible complete functional set concentricity condensate conductance conductibility conductor Cone configure Conical connected in star consumption control accuracy control action control instrumentation(C&I) control button(knob) control console(desk) controller convection pass converter
火力发电厂常用英语词汇
v1.0 可编辑可修改1 火力发电站常用英语技术词汇boiler house: 锅炉房coal conveyor 输煤装置coal bunker: 煤仓coal mill磨煤机steam boiler, water boiler tube 蒸汽锅炉，管式锅炉furnace(combustion chamber): 炉膛 ( 燃烧室 )water tube: 水管ash pit 灰坑superheater: 过热器water preheater: 水预热器air preheater: 空气预热器gas duct(flue): 烟气管 , 烟道dust collecting plant: 集尘室electrical precipitation plant: 电气除尘室induced draught fan: 引风机chimney: 烟囱deaerator: 除氧器feed water tank: 供水箱boiler feed pump: 给水泵switchgear: 开关设备cable tunnel: 电缆通道cable cellar: 电缆槽turbine room: 汽轮机室steam turbine with alternator: 蒸汽汽轮发电机组 economizer: 省煤器steam drum: 汽包surface condenser: 表面凝汽low-pressure preheater: 低压预热器circulating water pipe(pump): 循环水管control room: 控制室electrostatic dustremover(precipitator): 静电除尘器pulverizer 磨煤机slag pump 灰渣泵thermal cycle: 热力循环(net)heat rate: （净）热耗率Assemblie: 集合，集结，组装comment 注释，评论module : 模块 standby: 备用proximity 相近，接近，亲近v1.0 可编辑可修改2detector: 探测器 bracket: 支架 interlocks 互锁，联锁 axial: 轴向的 surge conditions: 喘振 :accessory: 附件 pulsation: 有节奏的跳动，跳动fossil fired: 燃煤 intent: 意图，目的，意向intend: 意指，想要，打算 consistent: 一致的，调和的 practice: 惯例，实习，实践 intrinsic: 固有的，内在的 procurement 获得，获取fabrication: 制作，构成，伪造物 vent: 通风孔，出烟孔，出口，放出，排出， noncondensible gas: 不凝结气体 intermittent 间歇的，断断续续的 blowdown : 排污 tank: 桶，箱，罐 diagram: 图表 deaerator: 除氧器 corrosion : 侵蚀，腐蚀状态 concentration 集中，集合，浓缩，浓度recommend 推荐，介绍，托付，劝告 abnormal and normal conditions: 变工况和额定工况 warm up: 暖机 acid wash: 酸洗scale: 范围，水垢，水锈，比例，刻度 sludge :: 污泥，淤泥 foreign matter: 不相关的物质 facilitate: 推动，促进，使简化multistage: 多级的 remote control: 遥控safety relief valve: 安全卸压阀 gauge: 量规，量表，测量 manhole: 人孔，检修孔 equivalent: 等价物，相等的 forging:: 锻造 seat: 部位，座 socket welding: 管座焊接 enthalpy: 焓estimate: 评价，评估， 估价 parameters 参数，参量nominal : 名义上的，额定的，标称的 MS — Main Steam : 主蒸汽 Cycle:: 循环 Intercept: 截止v1.0 可编辑可修改Fetting: 附件Gage:: 规，表，压力计Taps: 接头test wells: 测点插孔stress-relieved: 应力消除thermometer: 恒温计steam purge system: 蒸汽吹扫系统centrifugal type pumps: 离心式泵friction losses: 磨擦损失solenoid: 螺线管modulat: 调整，调节criteria: 标准wrenches: 扳手pipe taps: 管接头 .3v1.0 可编辑可修改4A List of Abbreviations and Symbols in English-ChineseA ::Ash Handling System: 除灰系统 AH :Air Heater: 空气预热器AAh :Analyzer, Alarm High : 分析器，高值报警 :: AIV :Air Intake Valve: 进气阀ALIGN Alignment: 校正 ALKF :Airlock Feeder: 锁气器 AP ::Ash Slurry Pump: 灰浆泵 ATM :Atmosphere 大气AC ::Air Conditioner: 空气调节器 AFT :Atmosphere Flash Tank: 大气扩容器 AC :Alternating Current: 交流电ALM :Alarm:: 报警 AMP :Ampere: 安培AX THR BRG :Axis Thrust Bearing: 轴向推力，轴承 ATMZ :Atomizing: 雾化 AUTO :Automation 自动 AUX :Auxiliary: 辅助的 BA :Bottom Ash 底灰BAH ::Bottom Ash Hopper: 底灰斗 BLR ::Boiler: 锅炉BSD ::Boiler Shut Down: 停炉 BUSH :Bushing: 衬套 BYPS :Bypass:: 旁路BVD ::Boiler Vents and Drains:: 锅炉疏水放气 BFP :Boiler Feedwater Pump :: 锅炉给水泵 BFPT:Boiler Feedwater Pump Turbine: 锅炉给水泵汽机 BFW ::Boiler Feedwater: 锅炉给水BM :Boiler Master 锅炉主控 BMCR:BoilerMaximumContinuousRating: 锅炉最大连续出力 BFBP:: Boiler Feed Booster Pump: 锅炉给水增压泵 BNR :Burner: 燃烧器BOP :Balance Of Plant: 电厂辅机设备 BPC :Blade Pitch Control: 叶片节距控制 BT :Boiler Tube: 炉管 CH: Crusher House: 碎煤房 COMB ::Combustion 燃烧v1.0 可编辑可修改5COMP ::Compressed Air: 压缩空气 CONV ::Conveyer: 输送机CPL :Control Pannel Local: 就地控制盘CPM :Control Pannel Main: 主控盘CRT :Cathode Ray Tube: 阴极射线管 : CT Current Transformer: 变流器 CYCL :Cyclone: 旋风分离器 CAS :Casing:: 缸、壳 CB Circuit Breaker: 断路器 COMP :Complete: 完成CCCW :Closed Circulating Cooling Water: 闭式循环冷却水 CCW :Cycle Cooling Water: 循环水CCWHF ::Closed Cooling Water Heater闭式冷却水冷却器 CCWP :Closed Cooling WaterPump: 闭式冷却水泵 CS :Closed Cooling Water System 闭式冷却水系统 CH Coal Handling 煤的装卸CHK VLV :Check Valve: 逆止阀 CIRC: Circulation: 循环 CLR Cooler: 冷却器CLOW :Cooling Water: 冷却水 CMPR :Compressor: 压缩机 CNTL :Control: 控制 CNTLE :Controller:: 控制器 COND :Condensate: 凝结水 CONDTY :Conductivity: 导电率 CP: Condensate Pump: 凝结泵CIR: Circuit: 回路 COUPI :Coupling: 联轴器CP: Condensate Polisher: 除盐装置 CS: Control Switch 控制开关 CRSV :Cold Reheat Safety Valve: 再热器冷段安全阀 CV: Control Valve : 控制阀CWP: Circulation Water Pump: 循环水泵DMPR: Damper : 挡板DP Difference Pressure: 差压 DPIC:DifferentialPressureIndicating Controller 压差指示控制器 DPT: Differential Pressure Transmitter 压差变送器 DRN: Drain:v1.0 可编辑可修改6疏水DV Drain Valve:: 疏水阀 DC Direct Current: 直流电 DSH: Desuperheater: 减温器 DCA: Drain Cooler Approach: 疏水冷却器通道 DEAER Deaerator: 除氧器 DEV: Deviation: 偏差DIFFRLY: Differential Relay: 差动继电器DISCH VLV :Discharge Valve 排放阀 DIST: Disturbance:: 故障、扰动 DSCH: Discharge: 排出 ECON: Economizer:: 省煤器EP Electrical Static Precipitator: 静电除尘器ECC Eccentricity :: 偏心 EFF Efficiency: 效率EHC Electric Hydraulic Control: 电液控制EO Electric Operate: 电气操作 EQ Equipment: 设备 ER Error: 误差ES :Extraction System 抽气系统 ESC Escape: 逃逸、超出ESS Engineering Safety System: 保安系统EU Engineering Unit : 工程单位 EXH Exhaust: 排汽 EXT Extract: 抽出 FA :Fine Ash: 细灰FDR Feeder: 给料机FE :Flow Element:: 流量元件 FI :Flow Indicator:: 流量指示件 FDBK: Feedback: 反馈 FITG Fitting: 连接件 FLW Flow 流量FO :Fail Open: 故障时自动打开 FT: Flow Totalizer: 流量累加器 FT :Flow transmitter: 流量变送器 FV :Flow Control Valve 流量控制阀 FY :Flow Relay or Valve 流量传送器 FA: Failure Alarm: 故障报警 FD :Forced Draft : 强制通风 FDF Forced Draft Fan: 送风机 FIC :Flow Indicate Controller: 流量v1.0 可编辑可修改7指示控制器 FLT :Flash Tank : 扩容箱 FLD :Field 磁场 FLG :Flange: 法兰 FLM Flame: 火焰FWH Feed Water Heater 给水加热器 FO :Fuel Oil: 燃油 FREQ Frequency: 频率 FURN Furnace: 炉膛 GLD Gland: 密封 GRDR Grinder: 碎渣机 GND Grounding: 接地GC :Generator Cooling: 发电机冷却GESE Gland Steam Condenser Exhauster: 轴加风机 GMT Generator Main Trandformer: 发电机变压器 GRADGrandient: 梯度 GS :Gland Steam: 轴封蒸汽GSC :Gland Steam Condenser: 轴封加热器 GV :Governor Valve: 高压调门 H ::Heat Conservation 保温 HS: Hand Switch:: 手动开关 HTR Heater: 加热器HV: Hand Control Valve: 手动控制器 HY: Hand Relay or Transducer 手动继电器（转换器） H :Hand: 手动的 HB :Heat Balance: 热平衡 HD :Heater Drain:: 加热器疏水HDR :Header: 联箱 HL ::Heat Loss: 热损失 HMDY Humidity: 湿度HPH: High Pressure Heater: 高压加热器HPR :Hooper: 漏斗HPT :High Pressure Turbine: 高压汽机HR: Hot Reheat: 再热器热段 HR: Heat Rate: 热耗率HSV: Hot Reheat Safety Valve: 再热器热段安全阀 HVAC :Heating Ventilation & Air Conditioning:: 暖通 HW :Hotwell: 热井HV ::Hand Control Valve: 手动控制器 HYD :Hydraulic: 液力的 INTLK :Interlock : 联锁IC :Instrument and Control:: 仪表与v1.0 可编辑可修改8控制（热工） ICV ::Inrtermediate Control Valve 中压控制阀 ID :Induced Draft 抽风，引风 IDF ::Induced Draft Fan: 引风机 IGN ::Ignition: 点火装置 INLT :Inlet: 入口IPR ::Initial Pressure: 初压 INST :Instrument: 仪表 INVR :Inverter: 逆变器I /O:: Input/Output 输入 / 输出 IP :Intermediate Pressure: 中压 ISV ::Intermediate Pressure Turbine Steam Valve: 中压缸进汽阀 JP :Jet Pump: 喷射器LG :Level Gauge 液位计LVL ::Level: 水位，液位 LA :Level Alarm: 液位报警 LIM(LMIR): Limiter: 限制器 LKG:: Leakage:: 泄漏 LP :Low Pressure 低压 :Low Point : 低位LPH: Low Pressure Heater: 低压加热器LSH: Local Switch Hand: 就地开关 LUB: Lubricating Oil: 润滑油 M :Mechanical: 机械 M :Motor: 马达 MAG:: Magnetic: : 磁性 MOD ::Mode: 方式 :M/A :Manual/Automatic: 手动 / 自动MAN ::Manual :: 手动 MARG: Margin:: 裕量MAX ::Maximum: 最大的，最大值的 MCR ::Maximum Continuous Rating 最大连续出力 MCV:: Main Control Valve: 主控制阀MD :Modulation Damper: 调节挡板 MDBFP: Motor Driven Boiler Feedwater Pump: 电动给水泵 MEAS ::Measure : 测量MFT: Master Fuel Trip: 主燃料跳闸 MIN :Minimum: 最小的 MKUP (MU) Make-up: 补充 ML :Mill: 磨煤机 MN :Main: 主要的v1.0 可编辑可修改9. :Manual Operation: 手操MPT :Main Power Transformer: 主变压器MS :Main Steam 主蒸汽 MSV :Main Steam Valve: 主汽阀 NOZ: Nozzle: 喷嘴NPSH :Net Pump Suction Head: 泵的静吸压头OL: Overload: 过载OLR :Overload Relay: 过载继电器 OPER :Operation: 运行 OSC :Oscillograph: 示波器 OTLT: Outlet: 出口 PA: Primary Air: 一次风 PAF :Primary Air Fan: 一次风机PAH :Pressure Alarm High: 高压报警 PAL :Pressure Alarm Low: 低压报警 PB: Push Button 按钮 PC :Power Centre: 动力中心PC: Pressure Controller: 压力控制器 . :Pressure Control: 压力控制 PCP :Precipitator 除尘器PCV :Pressure Control Valve:: 压力控制阀 PDI :Pressure Differential Indication: 差压指示 PDT :Pressure Differential Trandsmitter: 差压变送器 PED :Pdestal:: 轴承座PERF CALC Performance Calculation:: 性能计算 PF: Power Factor 功率因数 PHTR: Preheater: 预热器PMP :Pump: 泵PNEU :Pneumatic: 气动的PR: Pressure Recorder: 压力记录计 PRG :Purge: 吹扫PRV :Pressure Relief Valve: 泄压阀 PRO :Protection: 保护 PROGR:: Program: 程序PT: Pressure Transmitter: 压力变送器PULV: Pulverizer: 磨煤机PVSV :Pressure Vacuum Safety Valve 压力真空安全阀 PW: Plant Water 厂用水PY: Pressure Relay: 压力继电器 QA: Quality:: 质量，性能v1.0 可编辑可修改10RB: Run Back: 快速降负荷 RCV :Recovering: 回收 RECIRC:: Recirculation 再循环 RECT :Rectifier: 整流器 RET :Return: 返回 RH: Reheater: 再热器RO: Restriction Orifice: 节流孔板 ROT :Rotor: 转子RTU :Remote Telemetry Unit:: 遥测装置 SA :Secondary Air: 二次风 SAT: Saturate: 饱和的SC :Steam Coil Air Heater:: 暖风器 SCAV :Scavenge: 吹扫SD: Shut-off Damper: 关断挡板 : Shut-Down 停机SEP :Separator 分离器 SG: Switchgear 开关装置 SH: Superheater: 过热器 SLS :Seals:: 密封 SO: Shut Off: 关闭 SPD :Speed: 转速 SPRA: Spray: 喷水 SPT :Support: 支持 : ST: Start: 启动，开始 STD-BY :Stand By: 备用 ST: System:: 系统 STM :Steam: 蒸汽 STR: Stator:: 定子 STRNR: Strainer: 滤器 SU: Start Up: 启动SV: Solenoid Valve: 电磁阀 SUCT: Suction: 吸入 SW: Switch: 开关 : Steam Water: 汽水 SBLWR: Soot Blower 吹灰器TBFP Turbine Drive Boiler Feedwater Pump 汽泵 TCV :Temperature Control Valve 温度控制.: Transfer Damper: 转换挡板 TE: Temperature Element: 温度元件 TG: Turbine-generator: 汽轮发电机 Turbine-gear: Turbine-gear: 汽机盘车 THERM :Thermal 热力的TMS: Turbine Master System: 汽机主控系统 TRANS :Transfer: 转换v1.0 可编辑可修改11TRBL: Trouble: 故障 TRKG: Tracking: 跟踪TT: Temperature Transmitter: 温度变送器TTD: Terminal Temperature Difference: 温度端差TW: Thermowell: 热电偶套管 UAM :Unit Automatic Master: 机组自动系统VAC: Vacuum: 真空 VAL: Value: 数值VB: Vibration 振动 VLV: Valve: 阀门 WH: Watthour 瓦小时 WP: Working Point: 工作点 WW: Water Wall 水冷壁WX: Watt Transducer: 功率转换器 COVER :Crossover 切换管 CV: Control Valve: 控制阀英汉对照表A/H ： AUTOMATION/HAND : 自动 / 手动 ;A/M ： AUTOMATION/MANUAL: 自动 / 手动 ; ALARM 报警 ;AUX ： AUXILIARY :: 辅助 ; BYPASS 旁路CLOSE 关（状态，常指阀门） ; CODE: 代码；编码COLD START — UP: 冷态启动 COMPUTER : 计算机 CURVE ， LINE: 曲线，线 DATA: 数据；文件；资料 DECREAS : 减少 DESK: 台，桌 DIGIT: 数字 DISK: 磁盘DYNAMIC ； DYNAMICAL: 动态 F ： FLOW 流量 ; FAST: 快 FIGURE: 图示 HIGH: 高HOT START — UP: 热态启动I ＆C ：INSTRUMENT AND CONTROL 仪表v1.0 可编辑可修改12与控制INCREAS: 增加INDICATION ； DISPLAY : 指示；显示 ; INLET 入口 ; INPUT 输入 ; INTERMEDIATE 中 KEYBOARD: 键盘 KW ： KILOWATT 千瓦 L ： LOAD 负荷，负载 ; LOC ： LOCAL : 就地 LOW: 低MCS ：MANAGMENT COMMAND SYSTEM 管理命令系统MODE : 方式，模式 MW ： MEGAWATT 兆瓦NORMAL: 正常 OFF : 关（状态） ;ON : 开（状态） ; OPEN: 开 ( 状态，常指阀门 ); OPERATE : 运行；操作 ; OUTLET 出口 ; OUTPUT 输出 ; P ： PRESSURE: 压力 ; PANEL 盘 PARAMETER : 参数 PIPE ； TUBE: 管道，管子 PLANT: 厂，站 POWER: 功率，电源 ; PRINT: 打印R ： RATE : 比率，速率 ;R ： RESISTANCE: 电阻 ; REM ： REMOTE : 摇控 ; RESET 复位 ROOM : 室 RPM:: 转 / 分 ; S ： SPEED 速度 ; SELECT 选择 SET POINT 设定点 SHUTDOWN : 停机 ; SIDE （某）侧，边 ; SILENCER 消音器 SLOW : 慢 STAND BY: 备用 ; START : 启动 ; STARTUP : 起动；启动 ;v1.0 可编辑可修改13STATIC 静态 STATION 站 STOP: 停止 ; SYMBOL 符号 SYSTEM: 系统T ： TEMPERATURE:: 温度 ; TEST: 试验 ;TRANSMITTIER;TRANSDUCER: 变送器；传感器 TRIP 跳闸 ;TRIP ACKNOW: 跳闸确认 UNAVAIL 不允许 ( 不能投用的 ) UNIT : 单元、机组 VALVE 阀门WARM START — UP: 温态启动ZOOM: 摄像机镜头锅炉部分ACTUAL MEGAWATT: 有功AIR DRAFT SEQUENCE: : 风机程序控制（顺控）AIR HEATER A MOTER: 空预器马达 A AIR HEATER LOC/REM SELECT: 空预器就地 / 遥控选择AIR HEATER MOTOR LEAD: 空预器马达选择AIR HTR A SEC AIR OUT TEM 空预器 A 二次风出口温度AIR PREHEATER: 空预器AIR SVCE SUPPLY: 服务空气 ALARM LIMITS: :: 报警限制 ALL AIR HTRS RUNNING 各空预器运行 ALL PULV GRP SHUTDOWN 所有磨组停运ASH — HOPPER: : 灰斗 ATTEMPERATOR: : 减温器AUX .ST: SPLY FOR ATOMIZ 辅助蒸汽供雾化蒸汽BOIL MILL A BNR MET TEMP 炉 A 磨组喷燃器金属温度BOIL MILL A GR1 WDBOX PR 炉 A 磨组第一组风箱压力BOILER AIR REQUIRED 锅炉风量需求（ >30% ）v1.0 可编辑可修改14BOILER EFFLUENT STORAGE: POOL 锅炉废水池BOILER FOLLOW MODE: 炉跟随方式 BOILER MASTER: 锅炉主控器 BOILER TRIP RESET: : 锅炉跳闸复位 BOILER: 锅炉 BURNNER: : 燃烧器 CHIMNEY ； STACK:: : 烟囱 CLEAN: 清扫 COAL BANKER: :: 煤仓 COAL FEEDER : 给煤机 COMBUSTION : 燃烧 CONVEYOR: 皮带机COORDINATE MODE 协调方式 CRUSHER: 破碎机DECR/INCR PRESS AT FIX LOAD:: 固定负荷方式增减压力 DOWM COMER:: 下降管DRAIN & VENT: 疏水和排气 ECONOMIZER : 省煤器EITHER FAN RUNNING : 任一风机运行 EITHER ID FAN RUNNING 任一吸风机运行ELECTROSTATIC PRECIPITATOR : 静电除尘器FD FAN A FLOW:: A 送风机流量 FD FAN/ID FAN A CONT DAMPER A 送 / 吸风机控制挡板FEED WATER FLOW: 给水流量 FEEDER LOCAL SELECT: 给煤机就地控制选择FEEDER REMOTE SELECT: 给煤机遥控选择FLUE GAS: 烟气FORCED DRAFT FAN : 送风机FUEL GAS ID FAN A OUTLET PRESS A 吸风机出口压力FURNACE PRESS: 炉膛压力 FURNACE: 炉膛 GAS COAL: :: 烟煤 HEADER : 联箱、母管 IGNITOR: : 点火器，油枪 INDUCED DRAFT FAN : 引风机INDUCED&FORCED DRAFTS: 吸送风机 INITIATE: 启动、引燃、激发、触发v1.0 可编辑可修改15ISOLATION: 隔离；绝缘LFO .DISCH .PRESS : 轻油出口压力 LIGHT OIL SEL GRP 1: 第一组轻油枪选择LIGHT OIL: 轻油 LUB OIL PUMP:: 润滑油泵MAIN STEAM STOP VLV: 主蒸汽截止阀 MAIN STEAM TEMP/PRESSURE/FLOW 主汽温度 / 压力 / 流量MAINTAINED IGNITORS PULVERIZER A:磨煤机A 油枪操作MANUAL LOAD SET/RATE:手动负荷设定 / 负荷率MANUAL MODE: 手动方式MANUAL THROTTEL PRESS SET POINT:手动节流压力设定值MILL A GROUP MASTER : A 磨组主控器 MILL A LOAD: A 磨组负荷MILL A OUT TEMP CONT DAMPER : A 磨组出口温度控制挡板MIN MAX LOAD （ LIMITS ） : 最大最小负荷（限制） MMMC ＝ MILLIMETER MERCURY ； MMH2O: 毫米汞柱；毫米水柱 O 2 IN THE FUEL GAS 烟气含氧量OPEN/CLOSE SWING VLVS 摆阀开 / 关 OPERATE MODE SELECT: 运行方式选择 PENDANT: : 悬吊管PLATEN SPARY CONTROL VLVS SIDE A : 屏过减温水 A 侧控制阀PLATEN SUPERHEATER: 屏过 PRESSURE DIFFERENCE: 压差 PRI AIR DUCT PRESS 一次风管压力 PRI AIR FAN A CONT DAMPER: A 侧一次风机控制挡板PRI AIR FAN A OUTLET PRESS A 一次风机出口压力PRI AIR FLOW MILL A CONT DAMPER 磨组一次风控制挡板PRI/SEC AIR FLOW MILL A A 磨组一次 /二次风流量PRIMARY AIR FAN: 一次风机 PRIMARY AIR SEQUENCE: 一次风控制 PULVERIZER : 磨煤机PULVERIZER EMERGENCE TRIP 磨煤机v1.0 可编辑可修改16紧急跳闸PULVERIZER INERT MODE SELECT: 磨煤机惰性方式选择PULVERIZER NORMAL MODE SELECT: 磨煤机正常方式选择PULVERIZER SELECTION A :: 磨煤机 A 选择PULVERIZER: M/A: SELECT 磨煤机手 / 自动选择 PURGE 吹扫RH ； REHEATER: 再热器 SAFETY VALVE:: 安全阀 SCANNER BLOWERS: 火检吹扫器 SEAL AIR FAN PRESS: 密封风机压力 SEAL AIR FAN:: : 密封风机SEC AIR DUCT PRESS: 二次风管压力 SEC AIR FLOW MILL A CONT DAMPER A 磨组二次风流量控制挡板SEC SH OUT STEAM TEM 二级过热器出口蒸汽温度SEC SH SPARY CONT VLVS SIDE A 二级过热器减温水 A 侧控制阀SECONDARY SH INLET TEMP 二级过热器进口温度SECONDARY: AIR 二次风 SH ； SUPERHEATER: : 过热器SH STEAM ELECTR VLV: 过热器电磁阀 SH STEAM TEMP SET POINT:: 过热温度设定点SH/RH SPARY WATER STOP VLVS:: 过热器 / 再热器减温水截止阀SH/RH SPRAY CONTROL VLVS SELECT 过热器 / 再热器减温水控制阀选择 SLIDING PRESS MODE: 滑压运行方式 SOOT BLOWER: 吹灰器 SPARK 火花，点火花SPEED CHANGE (NOT) PERMISSIVE: 速度切换（不）允许 SPRAY : 喷水STACKER RECLAIMER :: 堆取料机 START IGNITOR GRP 1: 第一组油枪点火STEAM DRUM: : 汽包 STEAM 蒸汽 STONE COAL: 无烟煤STOP IGNITORS GRP 1: 第一组油枪停止v1.0 可编辑可修改17STOP/START FEEDER 给煤机停止 / 启动STOP/START IGNITORS: 油枪停止 / 启动STOP/START MILL: 磨组停止 / 启动 STOP/START PA FLOW: 一次风停止 / 启动STOP/START PULVERIZER 磨煤机停止 / 启动STOP/START SEQUENCE PULVERIZER A: 磨煤机 A 程序停止 / 启动 THROTTLE PRESS:: 节流压力TRANSPORT AIR SEQUENCE 风量程序控制（顺控）TURB FIRST STAGE PRESS 汽机第一级( 调节级 ) 压力TURBINE FOLLOW MODE: 机跟随方式 TURBINE MASTER: 汽机主控器 TWIN FLOW AIR HTR A CONT VLV: : 双流式空预器控制阀 UNLOADER: :: 卸煤机 WATER 水WATERWALL: : 水冷壁 汽机部分:EMERG OIL PUMP: 事故油泵 <P>CICR PMP DISCHARGE VLV: 循环泵出口阀1ST STAGE PRESS: 第一级压力 ACTUAL MEGA WATT: : 实际负荷数 AMS ： ADMISSION: MODE SELECTION 进汽方式选择AUX STEAM HEADER: : 辅汽联箱 AUX STEAM TEMP CONTROL: 辅汽温度控制AUX STM HEADER PRESS CONTROL VLV 辅汽联箱压力控制阀 BALANCE: : 平衡 BEARING BRASS:: 轴瓦 BEARING: : 轴承 BLADE 叶片BOILER FOLLOW MODE: 锅炉跟随方式 BOOSTER FEED PUMP: 前置给水泵 CICR WTR PUMP: 循环泵 CIRCULATING PUMP: : 循环泵 CIRCULATING: 循环v1.0 可编辑可修改18CLOSED COOLING WATER: 闭式冷却水 CLOSED COOLING WTR PUMP: 闭式冷却水泵CMPTR: : 计数器 CONDENSATE PUMP: 凝泵CONDENSER AIR SUCTION VLV: 凝汽器抽空气阀CONDENSER HOT WELL: : 热井 CONDENSER LEVEL CONTROL VLV: 凝汽器水位控制阀 CONDENSER: 凝汽器CONDS EXTR PUMP DISCH : 凝结水抽吸泵出口CONDS STOR TANK LEVEL: 凝结水储水箱水位COOLER: : 冷却器 COOLNG WTR PUMP: 水冷泵 COORDINATE MODE: : 协调方式 CV ： CONTROL VALVE 高压调门 CYLINDER 、 CASING: 汽缸DEAERATOR LEVEL CONTROL VLV: 除氧器水位控制阀DEAERATOR: : 除氧器DECR PRESS AT FIX LOAD: 在负荷不变下减压DEMI WATER: 除盐水DISPATCH PARTICIPATION 调度（参与）指令DURM PRESSURE:: 汽包压力 EJECTOR: 喷射器，抽气器EMERGENCY GOVERNOR 危急保安器 EXHAUST: 排汽 EXPANSION: 膨胀EXTR ST TO HP HTR 抽汽至高加 EXTRACTION STEAM 抽汽 FILTER: : 滤网 FLANGE 法兰FUNCTION GROUP: 功能组FW CONTROL VALVE ' S BYPASS VLV: 给水控制阀的旁路阀FW FLOW 30% CONTROL VLV : 30% 给水控制阀FW FLOW MASTER CONTROL: 给水流量主控FW HP HTR DISCH TEMP: 给水高加出口v1.0 可编辑可修改19温度FW PUMP RECIRCUL CONTROL VLV 给水泵循环控制阀 FW VLV: 给水阀门 GEARING: 盘车 GOVERNOR: 调速器HP ATTEM PRESS CONTROL VLV: 高旁减温水压力控制阀HP ATTEMP BLOCK VLV: 高旁减温水闭锁阀HP BYPASS ＆ HP ATTEMP VLVS: 高压旁路及减温水阀HP BYPASS PRESS CONTROL VLV 高旁压力控制阀HP BYPASS PRESS SET POINT: 高旁压力设定值HP BYPASS TEMP CONTROL VALVE 高旁温度控制阀HP ＆LP BYPASS COMMAND 高压及低压旁路指令HPH ： HIGH PRESSURE HEATER : 高加 HYDRAULIC OIL STATION PUMP: 液压油站泵INCR PRESS AT FIX LOAD: 在负荷不变下增压INT POS: 中间状态IV ： INTERMEDIATE VALVE 中压联合汽门JACKING OIL PUMP 顶轴油泵 LP HTR STOP VLV 低加截止阀LP ＆ HP BYPASS PRESS SIDE A 低压或高压旁路A 侧压力LP ＆ HP BYPASS TEMP SIDE A 低压或高压旁路A 侧温度LPH ： LOW PRESSURE HEATER: 低加 LUBE OIL PUMP: 润滑油泵 MAKE － UP WATER: 补给水 MANUAL LOAD RATE 手动负荷率 MANUAL LOAD SET 手动负荷设定 MANUAL Throttle Press Set Point 手动节流压力设定值MEASURE SELECTION 测量选择站 MOP ： MAIN OIL PUMP: 主油泵 MOTOR DRIVEN FEED WATER PUMP 电动给水泵v1.0 可编辑可修改20MSV ： MAIN STOP VALVE: 主汽阀 NOZZLE 喷嘴OIL PURIFIER: 净油器 OIL STORAGE TANK : 储油箱 OPERATE MANUAL MODE: 手动方式 OPERATE MODE SELECT: 运行方式选择 PILOT VALVE: 错油门PLATEN SH INLET TEMP SIDE A: A 侧屏过入口温度PRIMARY SH STOP VALVE: 一级过热器截止阀PUMP A DISCH PRESS : A 泵出口压力 RH SPRAY BLOCK VLVSTRIP INIT 再热器喷水闭锁阀跳闸启动RH SPRAY WTR STOP VLVS: 再热器喷水截止阀RH STEAM ATTEM FLOW: 再热喷水流量 RH STEAM TEMP OUTLET: 再热器出口温度 ROTOR 转子 SEAL: 密封 SHAFT 轴SILENCER: 消音器SLIDING PRESS MODE: 滑压方式 SPEED INDICATOR OR SPEED METER: : 转速表 STATOR 定子STEAM TURBINE : 汽轮机ST － UP BOIL FDW PUMP: 启动给水泵 SUCTION PUMP: 抽吸泵SURGE APPROACH: 喘振 SYNCHRONIZER: 同步器TFW PMP DISCHARGE VLV: 汽动泵出口阀 TFW PUMP MAIN OIL PMP: 汽动给水泵的主油泵THROTTLE ORIFICE 节流孔板 TURBINE DRIVEN FEED WATER PUMP: 汽动给水泵TURBINE FW PUMP AUX ＆ VLV 小机给水泵辅汽及阀门TURBINE GENERATOR: 汽轮发电机组 TURBINE INLET PRESS: 汽机入口压力 TURBINE MASTER : 汽机主控器 TURBING FOLLOW MODE: 汽机跟随方式 VACCUM 真空v1.0 可编辑可修改21VACUUM BROKEN VALVE: 真空破坏门 VACUUM SEQ : 真空程控 VIBRATION: 振动 电液调节及控制部分1STAGE PRESSURE FEEDBACK: 第一级压力反馈ABNORMAL CONDITION: 异常状态 ACCELERATION: 加速度 ACTIVE POWER:: 有功功率 ADMISSION MODE: 进汽方式 ADS(ALARM DISPLAY SELECT PANELS) 报警显示选择屏 AERIAL LINE: 架空线ALTERNATING CURRENT (AC): 交流 AMPERE: 安培ANGLE OF LAG: 滞后角 ANGLE OF LEAD: 超前角 ANODE: 阳极 ARC: 电弧 ARMATURE 电枢AST ： AUTO SHUT-DOWN TRIP: 自动停机遮断ASYNCHRONOUS MOTOR: 异步电动机 AT SET SPEED: 在设定速度位置 ATC ： AUTO TURBINE CONTROL: 自动汽轮机控制AUTOFORMER: 自藕变 AUTORECLOSING : 自动重合闸 AUXI TRANSFORMER : 厂用变 BACK UP TRANSFORMER 备用变BACK-UP OVERSPEED TRIP TEST 备用超速跳闸试验 ELECTRICAL TRIP TEST 电气跳闸试验BACK-UP SPDSIG LOST: : 后备速度信号失去BARRING OIL PUMP 盘车油泵 BASE LOAD: 基荷 BATTERY : 电池BATTERY BACKED CLOCK 电池备用时钟 BDV ： BLOWDOWN VLV: 泄放阀 BOOSTER PUMP: 前置泵 BULB : : 灯泡BUS SECTION : 母线分段 BUS: 母线BUSBAR FRAME: 母线架v1.0 可编辑可修改22BUSCOUPLER: 母联 BUSHING 套管 CABLE 电缆 CAPACITANCE: 电容 CARRIER 载波 CATHODE : 阴极 CCR: 中控室CHARGING EQUIPMENT : 充电设备 CHEST /ROTOR WARMING: 腔室 / 转子预暖CIU : 计算机接口单元 CLOSE : 合闸CLOSED VALVES OVERSPEED TEST 关闭阀 超速CLOSED-LOOP : 闭环COIL:: 线圈COMBINED RECLOSING 综合重合闸 COMBINED REHEAT VALVES: 中压联合阀 COMMON SERVICES LOGIC SUITE:: 公用系统逻辑柜COMMUNICATION: 通讯 CONDUCTOR : 导体CONFIGURATION: 结构，布置，外形 : CONTROL OIL: 控制油 CORE: 铁芯CPU(CENTARL PROCESSING UNIT: 中心处理单元 CRT: 显示屏CURRENT TRANSFORMER: 电流互感器 CURRENT 电流CV:: 控制阀 DAS: 数据采集系统DECREASING LOAD RATE: : 减负荷率 DIESEL GENERATOR : 柴油发电机 DIRECT CURRENT (DC) 直流 DISCONNECTOR : 隔离开关DISTRIBUTED CONTROL SYSTEM: 分散控制系统 工程师工作站EHC STATUS: 电液调节系统状态 EHC ： ELECTRO-HYDRA CONTROL SYSTEM: 电液调节控制系统EHV MIMIC PANEL : 电气高压模拟屏 ELECTRICAL MALFUNCTION SYSTEM FAULT : 电气失灵系统故障v1.0 可编辑可修改23EMERGENCY OIL PUMP: 事故油泵 EMERGENCY SEAL OIL PUMP: 事故密封油泵ETS ： EMERGENCY TRIP SYSTEM: 危急跳闸系统EXCEPTION REPORT: 例外报告 EXCITE 励磁 EXCITOR 励磁机FA/PA POSITION : 全周 / 部分（进汽）位置FAST-ACTING SOLENOID: 快动电磁阀 FIRST STAGE PRESS 调节级压力 FIS :: 流量显示开关 FREQUENCY: 频率FRF ： FIRE RESISTANT FLUID:: 抗燃油FULL ARC : 全周进汽 GAS : 瓦斯GEN. SHAFT SEAL&STATOR WIND : 发电机密封及静子绕组 GENERATOR : 发电机 GROUNDING(EARTHING) 接地 H2 TEMP CONT V : 氢气温度控制阀 HARDWARE 硬件 HOLD: 保持HYDRAULIC FLUID PRESS: 抗燃油压力 数字控制站终端模件 IN STANDBY: 在备用状态 IND: :: 指示器 INDUCTANCE: 电感INHIBITED: 停止进行、禁止 INSULATOR 绝缘子INTERCEPT VALVE: 中间截流阀 INTERCEPT VALVES: 中间截止阀 INTERFACE 接口 KILOWATT 千瓦 LC: 液位控制器 LI: 液位显示 LIGHT: 照明 LINE 线路 LK: 液位控制站LOAD DECREASING ； AT SET LOAD 负荷减；在设定负荷 LOAD FLOW : 负荷潮流分布 LOAD INCREASING: 负荷增v1.0 可编辑可修改24LOAD LIMITING SET: 负荷极限设定 LOAD MONITORING: 负荷监视 LOAD SELECT: :: 负荷选择 LOAD SET: 负荷设定 LOAD: 负荷LOADING RATE LIMIT : 负荷（增、减）率限定LOCKED OUT: 闭锁 LOSS : 损耗LOSS OF PWR:: 失去电源 LVDT ： 线性位移差动变送器 MAGNETIC FIELD: 磁场 MAIN OIL PUMP: 主油泵MAIN SEAL OIL PMP : 主密封油泵 MAIN STEAM PRESS 主蒸汽压力MAIN TRANSFORMER STEP-UP TRANSFORMER: 主变MANUAL: 手动 MCC: 马达控制中心 MEGAWATT: 兆瓦 MFP : 多功能控制器 MOTOR: 电动机MSPL ： MAIN STEAM PRESSURE LIMITER : 主汽压力限制器 MSV: 主蒸汽阀NEUTRAL POINT: 中性点 OHM: 欧姆 OIL GAUGE: 油位表OPC ： OVERSPEED PROTECTION CONTROL: 超速保护控制OPEN-LOOP : 开环 OPER AUTO: 操作员自动 :: OPERATING MODE : 操作方式ORP ： OIL RESET PISTON: 油复位活塞 ORSV ： OIL RESET SOLENOID VLV 油复位电磁阀OTSV ： OIL TRIP SOLENOID VLV: 油跳闸电磁阀OVER CURRENT: 过流 OVER VOLTAGE : 过压 OVERLOAD: 过载 PART ARC : 部分进汽 PC: 动力中心 PDIS : 压差显示开关 PEAK LOAD: 峰荷v1.0 可编辑可修改25PERMANENT MAGNETIC GENERATORDF 永磁发电机 PG: 压力计 PHASE ANGLE : 相角 PHASE: 相PIC: 压力显示控制器 PK: 压力控制站 PLUG : 插头 PLUG SOCKET: 插座 POLE:: 电极POTENTIAL TRANSFORMER 电压互感器 POWER 功率POWER FACTOR: 功率因数POWER LOAD UNBALANCE: 功载不平衡 PP ： : PREESSURE POINT 压力检测点PRI SPD SIG LOST 一次速度信号失去 PS: 压力开关 PT: 压力变送器 REACTANCE: 电抗 REACTIVE POWER: 无功功率 RECLOSING : 重合闸 REHEAT PRESS:: 再热汽压力 REMOTE AUTO: 远方自动 REMOTE OPERATION : 远操 RESISTANCE: 电阻RSM ： ROTOR STRESS MONITORING: 转子热应力监视 : RSV: 再热汽截止阀 SAFELY OIL : 安全油SCR CONTROLLER: 可控硅整流控制器SEAL OIL: 密封油 SHUT-OFF VALVE:: 切断阀 SIGNAL: 信号SLOW MEDIUM FAST: 慢、中、快 SPEED INCREASING: 速度增 SPEED MONITORING: 速度监视 SPEED SET RPM : 转速设定 转 / 分 SPEED: 速度，转速START UP TRANSFORMER 启动变 STATOR WIND COOLING WATER PUMP: 定子绕组冷却水泵STEAM SEAL BY-PASS UNLOAD VLV: 蒸汽密封旁路泄放阀STEAM SEAL DIVERING VALV: 密封汽分流阀v1.0 可编辑可修改26STEAM SEAL SYS:: 蒸汽密封系统 SUCTION PMP A/M SEL: 抽吸泵手 / 自动选择SUCTION PUMP: 抽吸泵 SUPERVISORS DESK: 值长台 SWITCH 开关SWITCHGEAR : : 配电盘、开关装置 TELEPHONE: 电话TEST SELECT: 试验选择（联锁） THERMO-COUPLE: : 热电偶THREE ELEMENTS LEVEL CONTROLLER: 三冲量水位控制器THRUST BEARING WEAR DETECTOR TEST 推力轴承磨擦检测试验 TI : 温度显示器TIC :: 温度指示控制 TIME DELAY: 时间延迟 TP: 温度检测点TRANSFER AND FILTER PUMP: 输送和过滤油TRANSFORMER: 变压器 TRANSMISSION: 传输 TRIP 跳闸 TS: 温度开关 TSI: 汽机监视仪表 TT:: 温度变送器TURB LUBE OIL TEMP CONTROL V : 汽机润滑油温度控制阀TURBIN DRAIN VALVES: 汽机疏水阀 TURBINE LATCHED: 汽机挂闸TURN GEAR CONTROL SEQUENCE 盘车控制程序TURN GEAR MOTOR: 盘车主电机 TURN GEAR PIGGY: BACK MOTOR 盘车啮合电机UNINTERRUPTED POWER SUPPLY: 不间断电源UNIT CONTROL DESK: 机组控制台 UNIT TRANSFORMER:: 单元变 VACUUM TRIP: 真空跳闸 VALVE POSITION: 阀位置 VI : 阀位置指示 VOLT(V): 伏特 VOLTAGE 电压 VT: 阀位置变送器v1.0 可编辑可修改VV ： VENTILATING VALVE : 通风阀WARMING RATE: 暖机速率WATT: 瓦特WINDING: 绕组27。
火力发电厂常用英语词汇
火力发电站常用英语技术词汇boiler house: 锅炉房coal conveyor 输煤装置coal bunker: 煤仓coal mill磨煤机steam boiler, water boiler tube 蒸汽锅炉，管式锅炉furnace(combustion chamber): 炉膛( 燃烧室)water tube: 水管ash pit 灰坑superheater: 过热器water preheater: 水预热器air preheater: 空气预热器gas duct(flue): 烟气管, 烟道dust collecting plant: 集尘室induced draught fan: 引风机chimney: 烟囱deaerator: 除氧器feed water tank: 供水箱boiler feed pump: 给水泵switchgear: 开关设备cable tunnel: 电缆通道cable cellar: 电缆槽turbine room: 汽轮机室steam turbine with alternator: 蒸汽汽轮发电机组economizer: 省煤器steam drum: 汽包surface condenser: 表面凝汽low-pressure preheater: 低压预热器circulating water pipe(pump): 循环水管electrostatic dust remover(precipitator):静电除尘器pulverizer 磨煤机slag pump 灰渣泵thermal cycle: 热力循环(net)heat rate: （净）热耗率Assemblie: 集合，集结，组装comment 注释，评论module : 模块standby: 备用proximity 相近，接近，亲近detector: 探测器bracket: 支架interlocks 互锁，联锁axial: 轴向的surge conditions: 喘振:accessory: 附件pulsation: 有节奏的跳动，跳动fossil fired: 燃煤intent: 意图，目的，意向consistent: 一致的，调和的practice: 惯例，实习，实践intrinsic: 固有的，内在的procurement 获得，获取fabrication: 制作，构成，伪造物vent: 通风孔，出烟孔，出口，放出，排出，noncondensible gas: 不凝结气体intermittent 间歇的，断断续续的blowdown : 排污tank: 桶，箱，罐diagram: 图表deaerator: 除氧器corrosion : 侵蚀，腐蚀状态concentration 集中，集合，浓缩，浓度recommend 推荐，介绍，托付，劝告abnormal and normal conditions: 变工况和额定工况warm up: 暖机acid wash: 酸洗scale: 范围，水垢，水锈，比例，刻度sludge :: 污泥，淤泥foreign matter: 不相关的物质facilitate: 推动，促进，使简化multistage: 多级的remote control: 遥控safety relief valve: 安全卸压阀gauge: 量规，量表，测量manhole: 人孔，检修孔equivalent: 等价物，相等的forging:: 锻造seat: 部位，座socket welding: 管座焊接enthalpy: 焓estimate: 评价，评估，估价parameters 参数，参量nominal : 名义上的，额定的，标称的MS — Main Steam : 主蒸汽Cycle:: 循环Intercept: 截止Fetting: 附件Gage:: 规，表，压力计Taps: 接头test wells: 测点插孔stress-relieved: 应力消除thermometer: 恒温计steam purge system: 蒸汽吹扫系统centrifugal type pumps: 离心式泵friction losses: 磨擦损失solenoid: 螺线管modulat: 调整，调节criteria: 标准wrenches: 扳手pipe taps: 管接头.A List of Abbreviations and Symbols in English-ChineseA ::Ash Handling System: 除灰系统AH :Air Heater: 空气预热器AAh :Analyzer, Alarm High : 分析器，高值报警:: AIV :Air Intake Valve: 进气阀ALIGN Alignment: 校正ALKF :Airlock Feeder: 锁气器AP ::Ash Slurry Pump: 灰浆泵ATM :Atmosphere 大气AC ::Air Conditioner: 空气调节器AFT :Atmosphere Flash Tank: 大气扩容器AC :Alternating Current: 交流电ALM :Alarm:: 报警AMP :Ampere: 安培AX THR BRG :Axis Thrust Bearing: 轴向推力，轴承ATMZ :Atomizing: 雾化AUTO :Automation 自动AUX :Auxiliary: 辅助的BA :Bottom Ash 底灰BAH ::Bottom Ash Hopper: 底灰斗BLR ::Boiler: 锅炉BSD ::Boiler Shut Down: 停炉BUSH :Bushing: 衬套BYPS :Bypass:: 旁路BVD ::Boiler Vents and Drains:: 锅炉疏水放气BFP :Boiler Feedwater Pump ::锅炉给水泵BFPT:Boiler FeedwaterPump Turbine: 锅炉给水泵汽机BFW ::Boiler Feedwater: 锅炉给水BM :Boiler Master 锅炉主控BMCR:Boiler Maximum ContinuousRating: 锅炉最大连续出力BFBP::Boiler Feed Booster Pump: 锅炉给水增压泵BNR :Burner: 燃烧器BOP :Balance Of Plant: 电厂辅机设备BPC :Blade Pitch Control: 叶片节距控制BT :Boiler Tube: 炉管CH: Crusher House: 碎煤房COMB ::Combustion 燃烧COMP ::Compressed Air: 压缩空气CONV ::Conveyer: 输送机CPL :Control Pannel Local: 就地控制盘CPM :Control Pannel Main: 主控盘CRT :Cathode Ray Tube: 阴极射线管: CT Current Transformer: 变流器CYCL :Cyclone: 旋风分离器CAS :Casing:: 缸、壳CB Circuit Breaker: 断路器COMP :Complete: 完成CCCW :Closed Circulating Cooling Water: 闭式循环冷却水CCW :Cycle Cooling Water: 循环水CCWHF ::Closed Cooling Water Heater 闭式冷却水冷却器CCWP :Closed Cooling WaterPump: 闭式冷却水泵CS :Closed Cooling Water System 闭式冷却水系统CH Coal Handling 煤的装卸CHK VLV :Check Valve: 逆止阀CIRC: Circulation: 循环CLR Cooler: 冷却器CLOW :Cooling Water: 冷却水CMPR :Compressor: 压缩机CNTL :Control: 控制CNTLE :Controller:: 控制器COND :Condensate: 凝结水CONDTY :Conductivity: 导电率CP: Condensate Pump: 凝结泵CIR: Circuit: 回路COUPI :Coupling: 联轴器CP: Condensate Polisher: 除盐装置CS: Control Switch 控制开关CRSV :Cold Reheat Safety Valve: 再热器冷段安全阀CV: Control Valve : 控制阀CWP: Circulation Water Pump: 循环水泵DMPR: Damper : 挡板DP Difference Pressure: 差压DPIC: Differential Pressure IndicatingController压差指示控制器DPT:Differential Pressure Transmitter 压差变送器DRN: Drain: 疏水DV Drain Valve:: 疏水阀DC Direct Current: 直流电DSH: Desuperheater: 减温器DCA: Drain Cooler Approach: 疏水冷却器通道DEAER Deaerator: 除氧器DEV: Deviation: 偏差DIFFRLY: Differential Relay: 差动继电器DISCH VLV :Discharge Valve 排放阀DIST: Disturbance:: 故障、扰动DSCH: Discharge: 排出ECON: Economizer:: 省煤器EP Electrical Static Precipitator: 静电除尘器ECC Eccentricity :: 偏心EFF Efficiency: 效率EHC Electric Hydraulic Control: 电液控制EO Electric Operate: 电气操作EQ Equipment: 设备ER Error: 误差ES :Extraction System 抽气系统ESC Escape: 逃逸、超出ESS Engineering Safety System: 保安系统EU Engineering Unit : 工程单位EXH Exhaust: 排汽EXT Extract: 抽出FA :Fine Ash: 细灰FDR Feeder: 给料机FE :Flow Element:: 流量元件FI :Flow Indicator:: 流量指示件FDBK: Feedback: 反馈FITG Fitting: 连接件FLW Flow 流量FO :Fail Open: 故障时自动打开FT: Flow Totalizer: 流量累加器FT :Flow transmitter: 流量变送器FV :Flow Control Valve 流量控制阀FY :Flow Relay or Valve 流量传送器FA: Failure Alarm: 故障报警FD :Forced Draft : 强制通风FDF Forced Draft Fan: 送风机FIC :Flow Indicate Controller: 流量指示控制器FLT :Flash Tank : 扩容箱FLD :Field 磁场FLG :Flange: 法兰FLM Flame: 火焰FWH Feed Water Heater 给水加热器FO :Fuel Oil: 燃油FREQ Frequency: 频率FURN Furnace: 炉膛GLD Gland: 密封GRDR Grinder: 碎渣机GND Grounding: 接地GC :Generator Cooling: 发电机冷却GESE Gland Steam Condenser Exhauster: 轴加风机GMT Generator Main Trandformer: 发电机变压器GRAD Grandient: 梯度GS :Gland Steam: 轴封蒸汽GSC :Gland Steam Condenser: 轴封加热器GV :Governor Valve: 高压调门H ::Heat Conservation 保温HS: Hand Switch:: 手动开关HTR Heater: 加热器HV: Hand Control Valve: 手动控制器HY: Hand Relay or Transducer 手动继电器（转换器）H :Hand: 手动的HB :Heat Balance: 热平衡HD :Heater Drain:: 加热器疏水HDR :Header: 联箱HL ::Heat Loss: 热损失HMDY Humidity: 湿度HPH: High Pressure Heater: 高压加热器HPR :Hooper: 漏斗HPT :High Pressure Turbine: 高压汽机HR: Hot Reheat: 再热器热段HR: Heat Rate: 热耗率HSV: Hot Reheat Safety Valve: 再热器热段安全阀HVAC :Heating Ventilation& Air Conditioning:: 暖通HW :Hotwell: 热井HV ::Hand Control Valve: 手动控制器HYD :Hydraulic: 液力的INTLK :Interlock : 联锁IC :Instrument and Control:: 仪表与控制（热工）ICV ::Inrtermediate ControlValve 中压控制阀ID :Induced Draft 抽风，引风IDF ::Induced Draft Fan: 引风机IGN ::Ignition: 点火装置INLT :Inlet: 入口IPR ::Initial Pressure: 初压INST :Instrument: 仪表INVR :Inverter: 逆变器I /O:: Input/Output 输入/ 输出IP :Intermediate Pressure: 中压ISV ::Intermediate Pressure Turbine Steam Valve: 中压缸进汽阀JP :Jet Pump: 喷射器LG :Level Gauge 液位计LVL ::Level: 水位，液位LA :Level Alarm: 液位报警LIM(LMIR): Limiter: 限制器LKG:: Leakage:: 泄漏LP :Low Pressure 低压L.P :Low Point : 低位LPH: Low Pressure Heater: 低压加热器LSH: Local Switch Hand: 就地开关LUB: Lubricating Oil: 润滑油M :Mechanical: 机械M :Motor: 马达MAG:: Magnetic: : 磁性MOD ::Mode: 方式:M/A :Manual/Automatic: 手动/ 自动MAN ::Manual :: 手动MARG: Margin:: 裕量MAX ::Maximum: 最大的，最大值的MCR ::Maximum Continuous Rating 最大连续出力MCV:: Main Control Valve:主控制阀MD :Modulation Damper: 调节挡板MDBFP: Motor Driven Boiler FeedwaterPump: 电动给水泵MEAS ::Measure :测量MFT: Master Fuel Trip: 主燃料跳闸MIN :Minimum: 最小的MKUP (MU) Make-up: 补充ML :Mill: 磨煤机MN :Main: 主要的M.O. :Manual Operation: 手操MPT :Main Power Transformer: 主变压器MS :Main Steam 主蒸汽MSV :Main Steam Valve: 主汽阀NOZ: Nozzle: 喷嘴NPSH :Net Pump Suction Head: 泵的静吸压头OL: Overload: 过载OLR :Overload Relay: 过载继电器OPER :Operation: 运行OSC :Oscillograph: 示波器OTLT: Outlet: 出口PA: Primary Air: 一次风PAF :Primary Air Fan: 一次风机PAH :Pressure Alarm High: 高压报警PAL :Pressure Alarm Low: 低压报警PB: Push Button 按钮PC :Power Centre: 动力中心PC: Pressure Controller: 压力控制器P.C. :Pressure Control: 压力控制PCP :Precipitator 除尘器PCV :Pressure Control Valve:: 压力控制阀PDI :Pressure Differential Indication: 差压指示PDT :Pressure Differential Trandsmitter: 差压变送器PED :Pdestal:: 轴承座PERF CALC Performance Calculation::性能计算PF: Power Factor 功率因数PHTR: Preheater: 预热器PMP :Pump: 泵PNEU :Pneumatic: 气动的PR: Pressure Recorder: 压力记录计PRG :Purge: 吹扫PRV :Pressure Relief Valve: 泄压阀PRO :Protection: 保护PROGR:: Program: 程序PT: Pressure Transmitter: 压力变送器PULV: Pulverizer: 磨煤机PVSV :Pressure Vacuum Safety Valve 压力真空安全阀PW: Plant Water 厂用水PY: Pressure Relay: 压力继电器QA: Quality:: 质量，性能RB: Run Back: 快速降负荷RCV :Recovering: 回收RECIRC:: Recirculation 再循环RECT :Rectifier: 整流器RET :Return: 返回RH: Reheater: 再热器RO: Restriction Orifice: 节流孔板ROT :Rotor: 转子RTU :Remote Telemetry Unit:: 遥测装置SA :Secondary Air: 二次风SAT: Saturate: 饱和的SC :Steam Coil Air Heater:: 暖风器SCAV :Scavenge: 吹扫SD: Shut-off Damper: 关断挡板: Shut-Down 停机SEP :Separator 分离器SG: Switchgear 开关装置SH: Superheater: 过热器SLS :Seals:: 密封SO: Shut Off: 关闭SPD :Speed: 转速SPRA: Spray: 喷水SPT :Support: 支持:ST: Start: 启动，开始STD-BY :Stand By: 备用ST: System:: 系统STM :Steam: 蒸汽STR: Stator:: 定子STRNR: Strainer: 滤器SU: Start Up: 启动SV: Solenoid Valve: 电磁阀SUCT: Suction: 吸入SW: Switch: 开关:Steam Water: 汽水SBLWR: Soot Blower 吹灰器TBFP Turbine Drive Boiler FeedwaterPump 汽泵TCV :Temperature ControlValve 温度控制T.B.: Transfer Damper: 转换挡板TE: Temperature Element: 温度元件TG: Turbine-generator: 汽轮发电机Turbine-gear: Turbine-gear: 汽机盘车THERM :Thermal 热力的TMS: Turbine Master System: 汽机主控系统TRANS :Transfer: 转换TRBL: Trouble: 故障TRKG: Tracking: 跟踪TT: Temperature Transmitter: 温度变送器TTD: Terminal Temperature Difference:温度端差TW: Thermowell: 热电偶套管UAM :Unit Automatic Master: 机组自动系统VAC: Vacuum: 真空VAL: Value: 数值VB: Vibration 振动VLV: Valve: 阀门WH: Watthour 瓦小时WP: Working Point: 工作点WW: Water Wall 水冷壁WX: Watt Transducer: 功率转换器COVER :Crossover 切换管CV: Control Valve: 控制阀英汉对照表A/H ：AUTOMATION/HAND : 自动/ 手动;A/M ：AUTOMATION/MANUAL: 自动/ 手动;ALARM 报警;AUX ：AUXILIARY :: 辅助; BYPASS 旁路CLOSE 关（状态，常指阀门）;CODE: 代码；编码COLD START — UP: 冷态启动COMPUTER : 计算机CURVE ，LINE: 曲线，线DATA: 数据；文件；资料DECREAS : 减少DESK: 台，桌DIGIT: 数字DISK: 磁盘DYNAMIC ；DYNAMICAL: 动态F ：FLOW 流量;FAST: 快FIGURE: 图示HIGH: 高HOT START — UP: 热态启动I＆C ：INSTRUMENT AND CONTROL仪表与控制INCREAS: 增加INDICATION ；DISPLAY : 指示；显示;INLET 入口;INPUT 输入;INTERMEDIATE 中KEYBOARD: 键盘KW ：KILOWATT 千瓦L ：LOAD 负荷，负载;LOC ：LOCAL : 就地LOW: 低MCS ：MANAGMENT COMMANDSYSTEM 管理命令系统MODE : 方式，模式MW ：MEGAWATT 兆瓦NORMAL: 正常OFF : 关（状态）;ON : 开（状态）;OPEN: 开( 状态，常指阀门); OPERATE : 运行；操作; OUTLET 出口;OUTPUT 输出;P ：PRESSURE: 压力;PANEL 盘PARAMETER : 参数PIPE ；TUBE: 管道，管子PLANT: 厂，站POWER: 功率，电源;PRINT: 打印R ：RATE : 比率，速率;R ：RESISTANCE: 电阻;REM ：REMOTE : 摇控;RESET 复位ROOM : 室RPM:: 转/ 分;S ：SPEED 速度;SELECT 选择SET POINT 设定点SHUTDOWN : 停机;SIDE （某）侧，边;SILENCER 消音器SLOW : 慢STAND BY: 备用;START : 启动;STARTUP : 起动；启动;STATIC 静态STATION 站STOP: 停止;SYMBOL 符号SYSTEM: 系统T ：TEMPERATURE:: 温度;TEST: 试验;TRANSMITTIER;TRANSDUCER: 变送器；传感器TRIP 跳闸;TRIP ACKNOW: 跳闸确认UNAVAIL 不允许( 不能投用的)UNIT : 单元、机组VALVE 阀门WARM START — UP: 温态启动ZOOM: 摄像机镜头锅炉部分ACTUAL MEGAWATT: 有功AIR DRAFT SEQUENCE: : 风机程序控制（顺控）AIR HEATER A MOTER: 空预器马达AAIR HEATER LOC/REM SELECT: 空预器就地/ 遥控选择AIR HEATER MOTOR LEAD: 空预器马达选择AIR HTR A SEC AIR OUT TEM 空预器A 二次风出口温度AIR PREHEATER: 空预器AIR SVCE SUPPLY: 服务空气ALARM LIMITS: :: 报警限制ALL AIR HTRS RUNNING 各空预器运行ALL PULV GRP SHUTDOWN 所有磨组停运ASH — HOPPER: : 灰斗ATTEMPERATOR: : 减温器AUX .ST: SPLY FOR ATOMIZ 辅助蒸汽供雾化蒸汽BOIL MILL A BNR MET TEMP 炉 A磨组喷燃器金属温度BOIL MILL A GR1 WDBOX PR 炉 A磨组第一组风箱压力BOILER AIR REQUIRED 锅炉风量需求（>30% ）BOILER EFFLUENT STORAGE: POOL锅炉废水池BOILER FOLLOW MODE: 炉跟随方式BOILER MASTER: 锅炉主控器BOILER TRIP RESET: : 锅炉跳闸复位BOILER: 锅炉BURNNER: : 燃烧器CHIMNEY ；STACK:: : 烟囱CLEAN: 清扫COAL BANKER: :: 煤仓COAL FEEDER : 给煤机COMBUSTION : 燃烧CONVEYOR: 皮带机COORDINATE MODE 协调方式CRUSHER: 破碎机DECR/INCR PRESS AT FIX LOAD:: 固定负荷方式增减压力DOWM COMER:: 下降管DRAIN & VENT: 疏水和排气ECONOMIZER : 省煤器EITHER FAN RUNNING : 任一风机运行EITHER ID FAN RUNNING 任一吸风机运行ELECTROSTATIC PRECIPITATOR : 静电除尘器FD FAN A FLOW:: A 送风机流量FD FAN/ID FAN A CONT DAMPER A送/ 吸风机控制挡板FEED WATER FLOW: 给水流量FEEDER LOCAL SELECT: 给煤机就地控制选择FEEDER REMOTE SELECT: 给煤机遥控选择FLUE GAS: 烟气FORCED DRAFT FAN : 送风机FUEL GAS ID FAN A OUTLET PRESS A吸风机出口压力FURNACE PRESS: 炉膛压力FURNACE: 炉膛GAS COAL: :: 烟煤HEADER : 联箱、母管IGNITOR: : 点火器，油枪INDUCED DRAFT FAN : 引风机INDUCED&FORCED DRAFTS: 吸送风机INITIATE: 启动、引燃、激发、触发ISOLATION: 隔离；绝缘LFO .DISCH .PRESS : 轻油出口压力LIGHT OIL SEL GRP 1: 第一组轻油枪选择LIGHT OIL: 轻油LUB OIL PUMP:: 润滑油泵MAIN STEAM STOP VLV: 主蒸汽截止阀MAIN STEAM TEMP/PRESSURE/FLOW 主汽温度/ 压力/ 流量MAINTAINED IGNITORS PULVERIZER A:磨煤机A油枪操作MANUAL LOAD SET/RATE:手动负荷设定/ 负荷率MANUAL MODE: 手动方式MANUAL THROTTEL PRESS SET POINT:手动节流压力设定值MILL A GROUP MASTER : A 磨组主控器MILL A LOAD: A 磨组负荷MILL A OUT TEMP CONT DAMPER : A 磨组出口温度控制挡板MIN MAX LOAD （LIMITS ）: 最大最小负荷（限制）MMMC ＝MILLIMETERMERCURY ；MMH2O: 毫米汞柱；毫米水柱O 2 IN THE FUEL GAS 烟气含氧量OPEN/CLOSE SWING VLVS 摆阀开/ 关OPERATE MODE SELECT: 运行方式选择PENDANT: : 悬吊管PLATEN SPARY CONTROL VLVS SIDEA : 屏过减温水 A 侧控制阀PLATEN SUPERHEATER: 屏过PRESSURE DIFFERENCE: 压差PRI AIR DUCT PRESS 一次风管压力PRI AIR FAN A CONT DAMPER: A 侧一次风机控制挡板PRI AIR FAN A OUTLET PRESS A 一次风机出口压力PRI AIR FLOW MILL A CONTDAMPER 磨组一次风控制挡板PRI/SEC AIR FLOW MILL A A 磨组一次/ 二次风流量PRIMARY AIR FAN: 一次风机PRIMARY AIR SEQUENCE: 一次风控制PULVERIZER : 磨煤机PULVERIZER EMERGENCE TRIP 磨煤机紧急跳闸PULVERIZER INERT MODE SELECT: 磨煤机惰性方式选择PULVERIZER NORMAL MODE SELECT: 磨煤机正常方式选择PULVERIZER SELECTION A :: 磨煤机A 选择PULVERIZER: M/A: SELECT 磨煤机手/ 自动选择PURGE 吹扫RH ；REHEATER: 再热器SAFETY VALVE:: 安全阀SCANNER BLOWERS: 火检吹扫器SEAL AIR FAN PRESS: 密封风机压力SEAL AIR FAN:: : 密封风机SEC AIR DUCT PRESS: 二次风管压力SEC AIR FLOW MILL A CONTDAMPER A 磨组二次风流量控制挡板SEC SH OUT STEAM TEM 二级过热器出口蒸汽温度SEC SH SPARY CONT VLVS SIDE A二级过热器减温水 A 侧控制阀SECONDARY SH INLET TEMP 二级过热器进口温度SECONDARY: AIR 二次风SH ；SUPERHEATER: : 过热器SH STEAM ELECTR VLV: 过热器电磁阀SH STEAM TEMP SET POINT:: 过热温度设定点SH/RH SPARY W ATER STOP VLVS:: 过热器/ 再热器减温水截止阀SH/RH SPRAY CONTROL VLVSSELECT 过热器/ 再热器减温水控制阀选择SLIDING PRESS MODE: 滑压运行方式SOOT BLOWER: 吹灰器SPARK 火花，点火花SPEED CHANGE (NOT) PERMISSIVE:速度切换（不）允许SPRAY : 喷水STACKER RECLAIMER :: 堆取料机START IGNITOR GRP 1: 第一组油枪点火STEAM DRUM: : 汽包STEAM 蒸汽STONE COAL: 无烟煤STOP IGNITORS GRP 1: 第一组油枪停止STOP/START FEEDER 给煤机停止/ 启动STOP/START IGNITORS: 油枪停止/ 启动STOP/START MILL: 磨组停止/ 启动STOP/START PA FLOW: 一次风停止/ 启动STOP/START PULVERIZER 磨煤机停止/ 启动STOP/START SEQUENCEPULVERIZER A: 磨煤机 A 程序停止/ 启动THROTTLE PRESS:: 节流压力TRANSPORT AIR SEQUENCE 风量程序控制（顺控）TURB FIRST STAGE PRESS 汽机第一级( 调节级) 压力TURBINE FOLLOW MODE: 机跟随方式TURBINE MASTER: 汽机主控器TWIN FLOW AIR HTR A CONT VLV: :双流式空预器控制阀UNLOADER: :: 卸煤机WATER 水WATERWALL: : 水冷壁汽机部分:EMERG OIL PUMP: 事故油泵<P>CICR PMP DISCHARGE VLV: 循环泵出口阀1ST STAGE PRESS: 第一级压力ACTUAL MEGA WATT: : 实际负荷数AMS ：ADMISSION: MODESELECTION 进汽方式选择AUX STEAM HEADER: : 辅汽联箱AUX STEAM TEMP CONTROL: 辅汽温度控制AUX STM HEADER PRESS CONTROLVLV 辅汽联箱压力控制阀BALANCE: : 平衡BEARING BRASS:: 轴瓦BEARING: : 轴承BLADE 叶片BOILER FOLLOW MODE: 锅炉跟随方式BOOSTER FEED PUMP: 前置给水泵CICR WTR PUMP: 循环泵CIRCULATING PUMP: : 循环泵CIRCULATING: 循环CLOSED COOLING WATER: 闭式冷却水CLOSED COOLING WTR PUMP: 闭式冷却水泵CMPTR: : 计数器CONDENSATE PUMP: 凝泵CONDENSER AIR SUCTION VLV: 凝汽器抽空气阀CONDENSER HOT WELL: : 热井CONDENSER LEVEL CONTROL VLV:凝汽器水位控制阀CONDENSER: 凝汽器CONDS EXTR PUMP DISCH : 凝结水抽吸泵出口CONDS STOR TANK LEVEL: 凝结水储水箱水位COOLER: : 冷却器COOLNG WTR PUMP: 水冷泵COORDINATE MODE: : 协调方式CV ：CONTROL VALVE 高压调门CYLINDER 、CASING: 汽缸DEAERATOR LEVEL CONTROL VLV:除氧器水位控制阀DEAERATOR: : 除氧器DECR PRESS AT FIX LOAD: 在负荷不变下减压DEMI WATER: 除盐水DISPATCH PARTICIPATION 调度（参与）指令DURM PRESSURE:: 汽包压力EJECTOR: 喷射器，抽气器EMERGENCY GOVERNOR 危急保安器EXHAUST: 排汽EXPANSION: 膨胀EXTR ST TO HP HTR 抽汽至高加EXTRACTION STEAM 抽汽FILTER: : 滤网FLANGE 法兰FUNCTION GROUP: 功能组FW CONTROL V ALVE ' S BYPASS VLV: 给水控制阀的旁路阀FW FLOW 30% CONTROL VLV : 30% 给水控制阀FW FLOW MASTER CONTROL: 给水流量主控FW HP HTR DISCH TEMP: 给水高加出口温度FW PUMP RECIRCUL CONTROL VLV 给水泵循环控制阀FW VLV: 给水阀门GEARING: 盘车GOVERNOR: 调速器HP ATTEM PRESS CONTROL VLV: 高旁减温水压力控制阀HP ATTEMP BLOCK VLV: 高旁减温水闭锁阀HP BYPASS ＆HP ATTEMP VLVS:高压旁路及减温水阀HP BYPASS PRESS CONTROL VLV 高旁压力控制阀HP BYPASS PRESS SET POINT: 高旁压力设定值HP BYPASS TEMP CONTROL VALVE高旁温度控制阀HP＆LP BYPASS COMMAND 高压及低压旁路指令HPH ：HIGH PRESSURE HEATER : 高加HYDRAULIC OIL STATION PUMP: 液压油站泵INCR PRESS AT FIX LOAD: 在负荷不变下增压INT POS: 中间状态IV ：INTERMEDIATE V ALVE 中压联合汽门JACKING OIL PUMP 顶轴油泵LP HTR STOP VLV 低加截止阀LP ＆HP BYPASS PRESS SIDE A 低压或高压旁路A侧压力LP ＆HP BYPASS TEMP SIDE A 低压或高压旁路A侧温度LPH ：LOW PRESSURE HEATER: 低加LUBE OIL PUMP: 润滑油泵MAKE －UP W ATER: 补给水MANUAL LOAD RATE 手动负荷率MANUAL LOAD SET 手动负荷设定MANUAL Throttle Press Set Point手动节流压力设定值MEASURE SELECTION 测量选择站MOP ：MAIN OIL PUMP: 主油泵MOTOR DRIVEN FEED WATER PUMP 电动给水泵MSV ：MAIN STOP V ALVE: 主汽阀NOZZLE 喷嘴OIL PURIFIER: 净油器OIL STORAGE TANK : 储油箱OPERATE MANUAL MODE: 手动方式OPERATE MODE SELECT: 运行方式选择PILOT VALVE: 错油门PLATEN SH INLET TEMP SIDE A: A侧屏过入口温度PRIMARY SH STOP VALVE: 一级过热器截止阀PUMP A DISCH PRESS : A 泵出口压力RH SPRAY BLOCK VLVSTRIP INIT 再热器喷水闭锁阀跳闸启动RH SPRAY WTR STOP VLVS: 再热器喷水截止阀RH STEAM ATTEM FLOW: 再热喷水流量RH STEAM TEMP OUTLET: 再热器出口温度ROTOR 转子SEAL: 密封SHAFT 轴SILENCER: 消音器SLIDING PRESS MODE: 滑压方式SPEED INDICATOR OR SPEEDMETER: : 转速表STATOR 定子STEAM TURBINE : 汽轮机ST －UP BOIL FDW PUMP: 启动给水泵SUCTION PUMP: 抽吸泵SURGE APPROACH: 喘振SYNCHRONIZER: 同步器TFW PMP DISCHARGE VLV: 汽动泵出口阀TFW PUMP MAIN OIL PMP: 汽动给水泵的主油泵THROTTLE ORIFICE 节流孔板TURBINE DRIVEN FEED WATER PUMP: 汽动给水泵TURBINE FW PUMP AUX ＆VLV 小机给水泵辅汽及阀门TURBINE GENERATOR: 汽轮发电机组TURBINE INLET PRESS: 汽机入口压力TURBINE MASTER : 汽机主控器TURBING FOLLOW MODE: 汽机跟随方式VACCUM 真空VACUUM BROKEN VALVE: 真空破坏门VACUUM SEQ : 真空程控VIBRATION: 振动电液调节及控制部分1STAGE PRESSURE FEEDBACK: 第一级压力反馈ABNORMAL CONDITION: 异常状态ACCELERATION: 加速度ACTIVE POWER:: 有功功率ADMISSION MODE: 进汽方式ADS(ALARM DISPLAY SELECTPANELS) 报警显示选择屏AERIAL LINE: 架空线ALTERNATING CURRENT (AC): 交流AMPERE: 安培ANGLE OF LAG: 滞后角ANGLE OF LEAD: 超前角ANODE: 阳极ARC: 电弧ARMATURE 电枢AST ：AUTO SHUT-DOWN TRIP: 自动停机遮断ASYNCHRONOUS MOTOR: 异步电动机AT SET SPEED: 在设定速度位置ATC ：AUTO TURBINE CONTROL: 自动汽轮机控制AUTOFORMER: 自藕变AUTORECLOSING : 自动重合闸AUXI TRANSFORMER : 厂用变BACK UP TRANSFORMER 备用变BACK-UP OVERSPEED TRIP TEST 备用超速跳闸试验ELECTRICAL TRIP TEST 电气跳闸试验BACK-UP SPDSIG LOST: : 后备速度信号失去BARRING OIL PUMP 盘车油泵BASE LOAD: 基荷BATTERY : 电池BATTERY BACKED CLOCK 电池备用时钟BDV ：BLOWDOWN VLV: 泄放阀BOOSTER PUMP: 前置泵BULB : : 灯泡BUS SECTION : 母线分段BUS: 母线BUSBAR FRAME: 母线架BUSCOUPLER: 母联BUSHING 套管CABLE 电缆CAPACITANCE: 电容CARRIER 载波CATHODE : 阴极CCR: 中控室CHARGING EQUIPMENT : 充电设备CHEST /ROTOR WARMING: 腔室/转子预暖CIU : 计算机接口单元CLOSE : 合闸CLOSED VALVES OVERSPEED TEST关闭阀超速CLOSED-LOOP : 闭环COIL:: 线圈COMBINED RECLOSING 综合重合闸COMBINED REHEAT V ALVES: 中压联合阀COMMON SERVICES LOGIC SUITE::公用系统逻辑柜COMMUNICATION: 通讯CONDUCTOR : 导体CONFIGURATION: 结构，布置，外形: CONTROL OIL: 控制油CORE: 铁芯CPU(CENTARL PROCESSING UNIT: 中心处理单元CRT: 显示屏CURRENT TRANSFORMER: 电流互感器CURRENT 电流CV:: 控制阀DAS: 数据采集系统DECREASING LOAD RATE: : 减负荷率DIESEL GENERATOR : 柴油发电机DIRECT CURRENT (DC) 直流DISCONNECTOR : 隔离开关DISTRIBUTED CONTROL SYSTEM:分散控制系统E.W.S.: 工程师工作站EHC STATUS: 电液调节系统状态EHC ：ELECTRO-HYDRA CONTROLSYSTEM: 电液调节控制系统EHV MIMIC PANEL : 电气高压模拟屏ELECTRICAL MALFUNCTIONSYSTEM FAULT : 电气失灵系统故障EMERGENCY OIL PUMP: 事故油泵EMERGENCY SEAL OIL PUMP: 事故密封油泵ETS ：EMERGENCY TRIP SYSTEM:危急跳闸系统EXCEPTION REPORT: 例外报告EXCITE 励磁EXCITOR 励磁机FA/PA POSITION : 全周/ 部分（进汽）位置FAST-ACTING SOLENOID: 快动电磁阀FIRST STAGE PRESS 调节级压力FIS :: 流量显示开关FREQUENCY: 频率FRF ：FIRE RESISTANT FLUID:: 抗燃油FULL ARC : 全周进汽GAS : 瓦斯GEN. SHAFT SEAL&STATORWIND : 发电机密封及静子绕组GENERATOR : 发电机GROUNDING(EARTHING) 接地H2 TEMP CONT V : 氢气温度控制阀HARDW ARE 硬件HOLD: 保持HYDRAULIC FLUID PRESS: 抗燃油压力I.C.S: 数字控制站终端模件IN STANDBY: 在备用状态IND: :: 指示器INDUCTANCE: 电感INHIBITED: 停止进行、禁止INSULATOR 绝缘子INTERCEPT VALVE: 中间截流阀INTERCEPT VALVES: 中间截止阀INTERFACE 接口KILOW ATT 千瓦LC: 液位控制器LI: 液位显示LIGHT: 照明LINE 线路LK: 液位控制站LOAD DECREASING ；AT SETLOAD 负荷减；在设定负荷LOAD FLOW : 负荷潮流分布LOAD INCREASING: 负荷增LOAD LIMITING SET: 负荷极限设定LOAD MONITORING: 负荷监视LOAD SELECT: :: 负荷选择LOAD SET: 负荷设定LOAD: 负荷LOADING RATE LIMIT : 负荷（增、减）率限定LOCKED OUT: 闭锁LOSS : 损耗LOSS OF PWR:: 失去电源LVDT ：线性位移差动变送器MAGNETIC FIELD: 磁场MAIN OIL PUMP: 主油泵MAIN SEAL OIL PMP : 主密封油泵MAIN STEAM PRESS 主蒸汽压力MAIN TRANSFORMER STEP-UPTRANSFORMER: 主变MANUAL: 手动MCC: 马达控制中心MEGAWATT: 兆瓦MFP : 多功能控制器MOTOR: 电动机MSPL ：MAIN STEAM PRESSURE LIMITER : 主汽压力限制器MSV: 主蒸汽阀NEUTRAL POINT: 中性点OHM: 欧姆OIL GAUGE: 油位表OPC ：OVERSPEED PROTECTION CONTROL: 超速保护控制OPEN-LOOP : 开环OPER AUTO: 操作员自动:: OPERATING MODE : 操作方式ORP ：OIL RESET PISTON: 油复位活塞ORSV ：OIL RESET SOLENOID VLV油复位电磁阀OTSV ：OIL TRIP SOLENOID VLV: 油跳闸电磁阀OVER CURRENT: 过流OVER VOLTAGE : 过压OVERLOAD: 过载PART ARC : 部分进汽PC: 动力中心PDIS : 压差显示开关PEAK LOAD: 峰荷PERMANENT MAGNETICGENERATORDF 永磁发电机PG: 压力计PHASE ANGLE : 相角PHASE: 相PIC: 压力显示控制器PK: 压力控制站PLUG : 插头PLUG SOCKET: 插座POLE:: 电极POTENTIAL TRANSFORMER 电压互感器POWER 功率POWER FACTOR: 功率因数POWER LOAD UNBALANCE: 功载不平衡PP ：: PREESSURE POINT 压力检测点PRI SPD SIG LOST 一次速度信号失去PS: 压力开关PT: 压力变送器REACTANCE: 电抗REACTIVE POWER: 无功功率RECLOSING : 重合闸REHEAT PRESS:: 再热汽压力REMOTE AUTO: 远方自动REMOTE OPERATION : 远操RESISTANCE: 电阻RSM ：ROTOR STRESS MONITORING: 转子热应力监视: RSV: 再热汽截止阀SAFELY OIL : 安全油SCR CONTROLLER: 可控硅整流控制器SEAL OIL: 密封油SHUT-OFF VALVE:: 切断阀SIGNAL: 信号SLOW MEDIUM FAST: 慢、中、快SPEED INCREASING: 速度增SPEED MONITORING: 速度监视SPEED SET RPM : 转速设定转/ 分SPEED: 速度，转速START UP TRANSFORMER 启动变STATOR WIND COOLING WATERPUMP: 定子绕组冷却水泵STEAM SEAL BY-PASS UNLOAD VLV:蒸汽密封旁路泄放阀STEAM SEAL DIVERING VALV: 密封汽分流阀STEAM SEAL SYS:: 蒸汽密封系统SUCTION PMP A/M SEL: 抽吸泵手/自动选择SUCTION PUMP: 抽吸泵SUPERVISORS DESK: 值长台SWITCH 开关SWITCHGEAR : : 配电盘、开关装置TELEPHONE: 电话TEST SELECT: 试验选择（联锁）THERMO-COUPLE: : 热电偶THREE ELEMENTS LEVELCONTROLLER: 三冲量水位控制器THRUST BEARING WEAR DETECTORTEST 推力轴承磨擦检测试验TI : 温度显示器TIC :: 温度指示控制TIME DELAY: 时间延迟TP: 温度检测点TRANSFER AND FILTER PUMP: 输送和过滤油TRANSFORMER: 变压器TRANSMISSION: 传输TRIP 跳闸TS: 温度开关TSI: 汽机监视仪表TT:: 温度变送器TURB LUBE OIL TEMP CONTROL V : 汽机润滑油温度控制阀TURBIN DRAIN VALVES: 汽机疏水阀TURBINE LATCHED: 汽机挂闸TURN GEAR CONTROL SEQUENCE盘车控制程序TURN GEAR MOTOR: 盘车主电机TURN GEAR PIGGY: BACK MOTOR盘车啮合电机UNINTERRUPTED POWER SUPPLY:不间断电源UNIT CONTROL DESK: 机组控制台UNIT TRANSFORMER:: 单元变VACUUM TRIP: 真空跳闸VALVE POSITION: 阀位置VI : 阀位置指示VOLT(V): 伏特VOLTAGE 电压VT: 阀位置变送器VV ：VENTILATING V ALVE : 通风阀WARMING RATE: 暖机速率WATT: 瓦特WINDING: 绕组。
火电英语词汇分类
火电英语词汇分类~锅炉部分~亚临界压力锅炉subcritical pressure boiler燃煤锅炉coal-fired boiler启动锅炉start-up boiler炉墙furnace wall管束（排）tube bundle管屏tube platen下降管downcomer上升管riser省煤器管economizer tube再热器管reheater tube过热器管superheated tube蛇形管coil吊挂管supporting tube水冷壁管water wall tube饱和蒸汽管saturated steam pipe水冷壁water wall鳍片管finned tube, fin tube, gilled tube联箱header锅炉本体boiler proper锅炉机组boiler unit炉膛boiler framework燃烧器furnace燃烧室combustion chamber油枪oil gun torch风门damper管板tube plate煤粉管道pulverized coal piping过热器superheater沸点boiling temperature吹灰器soot blower包墙过热器wall enclosure superheater再热器reheater炉膛容积furnace volume再热器冷段primary reheater汽水分离器steam separator, moisture separator再热器热段final reheater省煤器economizer空气预热器air preheater安全门safety valve防暴门explosion vent检查孔inspection hole三通阀three-way valve事故喷水阀emergency water spray valve锅炉排污blowdown大板梁plate girder, upper beam灰斗ash hopper空气压缩机air compressor混合器mixer磨煤机coal pulverizer, coal mill一次风机primary air fan送风机forced draft fan, force fan人孔门man hole引风机induced draft fan, induced fan膨胀补偿节expansion joint原煤斗raw coal bunker, raw coal silo结渣lagging煤粉仓pulverized coal bunker看火孔observation hole水循环water circulation风道air duct除尘器dust collector, precipitator伸缩节灰渣泵ash pump, slag pump风道air duct轴封泵shaft sealing pump伸缩节expansion joint灰浆泵ash slurry pump风管道air piping保温材料heat-insulating material除灰管道ash piping稳定燃烧stable combustion烟囱chimney, stack支吊架supports and hangers燃烧combustion水压试验hydraulic test负压negative pressure点火ignition正压positive pressure着火点firing point, ignition temperature冷风cold air锅炉上水boiler water filling热风hot air点火用油fuel oil for ignition停炉boiler shutdown熄火fire-off~汽轮机部分~汽轮机steam turbine高压汽缸high-pressure(HP) cylinder凝汽式汽轮机condensing steam turbine中压汽缸intermediate-pressure(IP) cylinder亚临界压力汽轮机subcritical pressure turbine低压汽缸low-pressure(LP) cylinder汽缸台板（底板）cylinder sole pin汽轮机转子turbine rotor汽封steam seal gland, steam sealing叶轮blade disc轴承支架bearing stoll, bearing bracket叶片blade, bucket主油泵main oil pump 喷嘴nozzle备用油泵emergency bearing oil pump固定螺钉dowel交流润滑油泵AC lube oil pump注油器oil injector直流润滑油泵DC lube oil pump喷油嘴oil nozzle高位油箱head oil tank, elevated oil tank杠杆lever凝汽器condenser轴shaft管板tube plate弹簧spring热水井hot well凝汽器喉部condenser throat凝结水泵condensate pump泵壳pump casing低压加热器low-pressure feed water heater高压加热器high-pressure feed water heater 除氧器deaerator除氧水箱deaerated water tank除盐水箱demineralized water tank汽动给水泵steam-driven feed water pump 前置水泵booster pump给水泵feed water pump疏水泵drain pump水室water chamber疏水扩容器drain flash tank挡板baffle plate封头end cover真空泵vaccum pump工业水泵industrial water pump, service water pump收球网ball screen胶球泵rubber ball recirculating pump主蒸汽系统main steam system支撑斜钢supporting wedge再热蒸汽系统reheat steam syetem自然通风冷却塔natural draft cooling tower抽汽系统extraction steam system主蒸汽管道main steam piping, live steam piping轴封shaft seal真空系统vaccum system凝结水系统condensate system再热蒸汽管道reheat steam system给水系统feed water system循环水系统circulating water system供油系统oil supply system工业水系统industrial water system, service water system抽汽管道steam extraction pipe供汽联箱steam header压缩空气管道compressed air piping疏水管道drain water piping氢气管道hydrogen piping凝结水管道condensate piping循环水管道circulating water piping冷却水管道cooling water piping给水管道feed water piping润滑油管lube oil piping除盐水管道demineralized water piping旁路门bypass valve减温水管道attemperating water piping球型阀globe valve再循环水管道recirculating water piping闸板阀gate valve排水管道water discharge piping疏水阀drain valve高压主汽门high-pressure main stop valve蝶阀butterfly valve中压主汽门intermediate pressure main stop valve转速rotating speed, revolution 热效率thermal efficiency, heat efficiency 过热度superheat degree新蒸汽压力initial steam pressure, live steam pressure温差temperature difference开启opening再热蒸汽冷段压力cold reheated steam pressure关闭closing再热蒸汽热段压力hot reheated steam pressure启动starting-up再热蒸汽热段温度hot reheated steam temperature停止shutting down再热蒸汽冷段温度cold reheated steam temperature检查inspection, examination低压缸排汽流量low-pressure cylinder exhaust steam flow巡检routing inspection再热蒸汽流量reheated steam flow主蒸汽流量steam flow法兰加热flange heating螺栓加热bolt heating正常状态normal condition清洗cleaning操作operation酸洗acid cleaning, pickling解体disassembly组装assembly检修maintenance拆开dismantling汽缸扣盖cylinder covering变形deformation毛刺burr裂纹crack锈蚀rusting壁厚wall thickness同心concentricity找正centering垫铁iron cushion, packing iron plate, adjusting pad找中心alignment台板sole plate天车turbine hall overhead crane管束tube bundle汽机基座turbine pedestal流量flow抽汽量steam extraction capacity海水sea water保温材料heat insulating material防腐anti-corrosion~电气部分~发电机electric generator, generator一次电压primary voltage发电机定子generator stator二次电压secondary voltage发电机转子generator stator一次绕组primary winding主变压器main transformer二次绕组secondary winding工作变压器operating transformer高压线路high-voltage line备用变压器standby transformer导电环conducting ring开关switch零电位zero potential按钮button漏电electric leakage电压voltage母线bus, busbar电流current测电笔test pencil电流强度current intensity验电器electroscope电阻resistance匝数number of turns电功率electric power屏蔽接地shield earthing 电压表voltmeter延迟时间delay time伏特volt绝缘insulation千伏kilovolt相序phase order, phase sequence电流表ammeter, amperemeter相电压phase voltage安培ampere电阻测量resistance measurement千瓦小时kilowatt-hour电压测量voltage measurement电位计potentiometer电流测定current measurement功率表wattmeter时间测定time measurement瓦特watt明线open wire, open conductor 千瓦kilowatt暗线concealed wire, concealed conductor兆瓦megawatt照明线路lighting line赫兹hertz控制control转速表speedometer输电transmission千伏安kilovoltampere带电live, electrified欧姆ohm原理图schematic diagram通风ventilation, draft电力系统electric power system避雷针lightning rod, lightning conductor控制台control board电源power source, power supply电负荷power load交流电源AC power source功率损失power loss直流电源DC power source供电power supply不停电电源uninterrupted power supply(UPS)发电power generation强电strong current操作人operator弱电weak current监护人guardian继电器relay通信communication锁闭装置locking device电话机telephone set断路器breaker, circuit breaker电话号telephone number接触器contactor电缆cable插件plug-in unit, insertion piece信号signal保护接地protective earthing连接器connector保护罩protective cover, protective housing单元unit熔断器cutout, fusible cutout主机main machine电缆cable系统system电缆芯cable core电子元件electronic单元控制室unit control room故障fault配电室switch room, distribution board room正常normal频率frequency异常abnormal毫安表millammeter告警alarm毫伏表millvoltmeter输入input电子计算机electronic computer 输出output架空线路overhead line信号状态signal status布线wiring结束end合上switch-on测试test重拨redial拨号dial直拨direct dialing断开switch-off~化学部分~化学加药处理chemical treatment feeding酸洗acid cleaning自来水raw water, crude water软化水softened water除盐水demineralized water过滤filtration去矿物质水demineralized water除气deaeration再生regeneration污染pollution腐蚀corrosion结垢scaling水垢scale离子交换树脂ion exchange resin石灰lime混床mixed bed并联in parallel串联in series溶解箱dissolving tank溶液箱solution tank取样装置sampling device溶质solute溶剂solvent~仪表与控制部分~温度计thermometer鼠标器mouse温差temperature difference驱动器drive压力开关pressure switch键盘keyboard标准大气压力standard atmosphere存储器storage, memory锅炉压力boiler pressure延时time delay风压air pressure在线on line喷嘴nozzle离线off line给水流量feed water flow扩展extension蒸汽流量steam flow扫描scan阻尼器snubber, damper刷新update总线bus阻塞clogging画面graphic display传输速率transmission rate存储storage源程序source program文字标题literal title滤波器filter图象信息graphic information返回return中间变量intermedium variable中断interrupt操作指导operation guide保留retain信息共享information sharing删除delect吹扫purge节点node 点火器igniter发送send, transmit灵敏度sensitivity接收receive精确度accuracy数据库data base灵活性flexibility调制解调器modulator-demodulator(MODEM)可扩展性expandability兼容compatibility分散度dispersity按钮button, pushbutton工作时间up time确认acknowledgement故障时间down time复位reset仪表measuring instrument开关switch~燃料部分~输煤栈桥coal belt conveyor gallery起吊孔lifting hole漏斗hopper燃煤品种category of coal输煤皮带conveyor belt结焦性coking property皮带速度belt velocity结渣性slagging property皮带宽度belt width固定碳fixed carbon驱动功率driving power设计煤种design coal机车locomotive闪点flash point煤气gas~综合部分~图纸drawing合金alloy平面图plan, plan view电焊electric welding校对check电焊条welding electrode审核review焊丝welding wire批准approve焊接welding数量quantity气孔blowhole重量weight咬边undercut材料material焊口裂纹weld seam crack图号drawing number坡口加工edge preparation测量measurement应力stress尺寸size, dimension着色剂colorants, coloring agent 中心距center distance蠕变creep加工余量finish allowance, machine allowance垫片gasket, pad, shim表面surface石棉垫asbestos pad, babbit cushion水平level中心孔center bore, center hole, center opening检验test, check, examination装配assembly, installation圆度ellipticity剖面section, cross-section~附加部分~ 长度length缺陷处理defect treatment面积area铭牌nameplate体积（容积）volume技术检验记录technical check record质量mass技术资料technical information, technical data重量weight事故accident, emergency能量energy发电量power generation, generated energy形状shape设备缺陷equipment defector方形square扩建工程extension project圆形round复印copying半径radius装订binding直径diameter出版publication周长circumference, perimeter主厂房布置图main machine building arrangement drawing参数parameter主厂房main machine hall, main power building温度temperature汽机房turbine hall, turbine house 压力pressure除氧间（除气间）deaerator bay真空vacuum锅炉房boiler hall, boiler house流量flow, flow capacity烟囱chimney, stack压缩compression灰场ash yard膨胀expansion渣场slag yard起动start-up, starting 灰坝ash dam 停机shutdown, outage, stoppage近期near future, short-term检测detection, test远期future, long-term 并联parallel connection底层ground floor串联series connection 地下室basement气体gas梁beam液体liquid柱column, pillar固体solid楼板floor slab标高elevation平台platform调试test and adjustment 扶梯stair试运行trial operation地面ground保温heat insulation, thermal insulation设备基础equipment foundation油漆paint煤场coal yard灭火器fire extinguisher采暖heating运行operation, running照明lighting业主owner通风ventilation合同contract安装erection, installation价格price。
火电厂英语词汇__锅炉部分
电力英语一、锅炉部分1．临界压力锅炉supercritical pressure boiler2.亚临界压力锅炉subcritical pressure boiler3.超高压锅炉super-high pressure boiler4.蒸汽锅炉steam boiler5.蒸汽发生器steam generator6.液态排渣锅炉wet bottom boiler7.固态排渣锅炉dry bottom boiler8.燃煤锅炉coal-fired boiler9.燃气锅炉Gas-fired boiler10.燃油锅炉oil-fired boiler11.自然循环锅炉natural circulation boiler12.汽包（锅筒）锅炉drum boiler13.强制循环锅炉controlled circulation boiler14.直流锅炉once-through boiler15.复合循环锅炉combined circulation boiler16.旋风炉cyclone furnace boiler17.沸腾炉fluidized bed combustion(FBC)boiler18.循环硫化床circulating fluidized bed combustion(FBC)boiler19.增压循环硫化床锅炉 pressurized circulating fluidized bed combustion(PCFBC)boiler20.链条锅炉chain-grate boiler21.热水锅炉hot-water boiler22.废热（余热）锅炉water-heat boiler, heat recover steam generator(HRSG)23.启动锅炉start-up boiler24.厂用锅炉auxiliary boiler25.垃圾焚烧锅炉refuse-fired boiler, refuse incinerator27.露天锅炉outdoor boiler28.单炉膛锅炉single furnace boiler29.双炉膛锅炉twin furnace boiler30.W火焰锅炉W-flame boiler, vertical-fired boiler31.L火焰锅炉L-shape furnace boiler32.塔式锅炉tower boiler33.箱式锅炉box-type boiler34．炉墙furnace wall35.汽包（锅筒）drum36.封头head37.汽包封头drum end plate, drum head38.下降管downcomer39.集中下降管centralized downcomer40.分散下降管distributed downcomer41.上升管riser42.管束（排）tube bundle43.管屏tube platen44.省煤器管economizer tube45.过热器管superheated tube46.再热器管reheater tube47.蛇形管coil48.吊挂管supporting tube49.引入管inlet pipe50.引出管outlet pipe51.饱和蒸汽管saturated steam pipe52.水冷壁管water wall tube53.鳍片管finned tube, fin tube, gilled tube54.内螺纹管rifled tube, grooved tube55.吸潮管moisture absorption piping56.水冷壁water wall57.膜式水冷壁membrane wall58.内螺纹水冷壁rifled tube water wall59.联箱header60.集汽联箱steam header61.卫燃带bailey wall, refractory belt62包墙管（包覆管）wall enclosure tube63.防渣管（弗斯顿管）slag screen, feston tube64.锅炉本体boiler proper65.锅炉机组boiler unit66.锅炉构架boiler structure67.炉膛boiler framework68.燃烧器furnace69.直流式燃烧器direct-flow burner70.旋流式燃烧器turbulent burner71.低NOX燃烧器low NOX burner72.摇摆式燃烧器tilting burner73.缝隙式燃烧器split burner74.燃烧室combustion chamber75.油枪oil gun torch76.风门damper77.一次风primary air78.二次风secondary air79.三次风tertiary air80.煤粉管道pulverized coal piping81.管板tube plate82.沸点boiling temperature83.过热器superheater84.前屏过热器front platen superheater85.后屏过热器rear plate superheater86.对流过热器convection superheater87.辐射过热器radiant superheater88.屏式过热器plate superheater89.顶棚过热器ceiling superheater90.包墙过热器wall enclosure superheater91.前包墙过热器front wall enclosure superheater92.后包墙过热器rear wall enclosure superheater93.侧包墙过热器side wall enclosure superheater94.吹灰器soot blower95.转动式吹灰器rotary soot bolwer96.伸缩式吹灰器retractable soot blower97.受热面积heating surface area, heat absorption area98.炉膛容积furnace volume99.炉膛热负荷furnace heat release rate, furnace heating absorption rate 100.汽水分离器steam separator, moisture separator101.起动分离器starting separator102.再循环管recirculating piping103.暖风器steam air heater104.再热器reheater105.再热器冷段primary reheater106.再热器热段final reheater107.顶棚ceiling108.省煤器economizer109.管式省煤器tube economizer110.管式空气预热器tubular air preheater111.回转式（再生式）空气预热器regenerative air preheater, rotary air preheater 112.板式空气预热器plate air preheater113.空气预热器air preheater114.三分仓空气预热器trisector regenerative air preheater115.漏风系数air leakage coefficient116.漏风率air leakage ratio117.漏风系统air leakage system118.漏风试验air leakage test119.安全门safety valve120.安全门开启压力opening pressure of safety valve121.安全门回座压力safety valve reseating pressure122.安全门压力整定试验pressure setting test of safety valve123.安全门动作压力safety valve operating pressure124.饱和蒸汽安全门saturated steam safety valve125. 过热蒸汽安全门superheated steam safety valve126.再热蒸汽安全门reheated steam safety valve127.防暴门explosion vent128.检查孔inspection hole129.事故喷水阀emergency water spray valve130.汽包事故放水阀emergency drum drain valve131.三通阀three-way valve132.反冲洗阀back wash valve133.取样阀sampling valve134.插板gate135.给水大旁路门feedwater overall bypass valve136.给水小旁路门feedwater individual bypass valve 137.大板梁plate girder, upper beam138.外护板outer casing139.锅炉排污blowdown140.定期排污扩容器intermittent blowdown flash tank141.连续排污扩容器continuous blowdown flash tank142.灰斗ash hopper143.冷灰斗bottom ash hopper, furnace hopper 144.混合器mixer145.齿圈（大牙轮）ring gear, geared ring146.空调器air conditioner147.空气压缩机air compressor148.给煤机coal feeder149.皮带式给煤机belt coal feeder150.刮板式给煤机scraper coal feeder151.叶轮式给煤机paddle coal feeder152.给粉机pulverizer coal feeder153.磨煤机coal pulverizer, coal mill154.钢球磨煤机tube mill155.中速辊式磨煤机roller mill, bowl mill, disk roll mill156.双进双出钢求磨煤机double inlet and outlet tube mill 157.中速磨煤机medium speed mill158.风扇磨煤机beater wheel mill, beater mill159.排粉风机pulverized coal exhauster160.一次风机primary air fan161. 烟气再循环风机gas recirculation fan162.送风机forced draft fan, force fan163.引风机induced draft fan, induced fan164.离心风机centrifugal fan165.轴流风机axial-flow fan166.双速风机double speed fan167.轴流静叶可调风机adjustable static-blade axial-flow fanfixed pitch axial-flow fan168.轴流动叶可调风机adjustable moving-blade axial-flow fanvariable pitch axial-flow fan169.原煤斗raw coal bunker, raw coal silo 170.煤粉仓pulverized coal bunker171.输粉机pulverized coal conveyer172.刮板输粉机scraper pulverized coal conveyer 173.螺旋输粉机pulverized coal screw conveyer 174.粗粉分离器classifier175.细粉分离器（旋风分离器）cyclone separator176.锁气器air lock, flap177.减速机speed reduce178.看火孔observation hole179.人孔门man hole180.重油泵heavy oil pump181.重油加热器heavy oil heater182.汽-汽热交换器biflux183.煤气罐gas tank184.膨胀补偿节expansion joint185.直吹式制粉系统direct firing pulverizing system 186.中贮式制粉系统bin storage type pulverizing system 187.锅炉效率boiler efficiency188.锅炉热力计算boiler thermodynamic calculation 189.锅炉空气动力计算boiler aerodynamic calculation 190.锅炉水循环计算boiler water circulation calculation 191.锅炉水力计算boiler hydrodynamic calculation 192.锅炉强度计算boiler strength calculation193.锅炉热平衡boiler heat balance calculation 194.正平衡法direct balance method195.反平衡法indirect balance method196.过剩空气系数excess air coefficient197.排烟温度flue gas temperature198.单位蒸量specific evaporation199.低温腐蚀low temperature corrosion200.高温腐蚀high temperature corrosion201.结渣lagging202.结垢腐蚀deposit corrosion203.飞灰磨损fly ash erosion204炉膛负压furnace draft205.最高允许温度maximum permissible temperature 206.炉膛正压furnace pressure207.水循环water circulation208.循环倍率circulation ratio209.除尘器dust collector, precipitator210.静电除尘器electrostatic precipitator211.整流装置rectifying device212.锤打装置rapping gear213.含尘浓度dust loading concentration214.煤灰细度dust fineness215.除尘效率dust collection efficiency216.干式除尘器dry dust collector217.湿式除尘器wet dust collector, scrubber218.文丘里除尘器venture scrubber219.布袋除尘器fabric filter, bag house220.钢珠除尘装置shot-cleaning device221.水膜式除尘器centrifugal scrubber222.灰渣泵ash pump, slag pump223.轴封泵shaft sealing pump224.灰浆泵ash slurry pump225.除尘水泵dedusting pump226.回收水池water recovery pond227.清水池clean water pond228.灰浆池ash slurry pond229.油泵坑oil pump pit230.灰库ash silo231.灰场ash yard232.灰坝ash yard dam233.耐火砖firebrick234.保温材料heat-insulating material235.干式除灰（气力除灰）pneumatic pressure ash handling 236.水力除灰hydraulic ash handling237.正压气力除灰pneumatic pressure ash handling 238.负压气力除灰pneumatic pressure ash handling 239.仓式泵fluidizing transporter240.空气斜槽airslide, air gravity conveyor241.灰渣分除bottom and fly ash separate handling 242.灰渣混除bottom and fly ash mixed handling 243.灰渣利用bottom and fly ash recovery244.排渣槽bottom ash hopper245.埋刮板捞渣机submerged slag conveyor246.螺旋式捞渣机screw slag conveyor247.碎渣机clinker grinder, slag crusher248.振动筛vibrating screen249.稳燃器flame stabiliaer250.燃烧器蜗壳burner spiral case251.雾化器atomization252.机械雾化mechanical atomization253.蒸汽雾化steam atomization254.空气雾化air atomization255.气固两相流动gas-solid two-phase flow256.闭路循环closed cycle257.蒸汽带水carryoery258.炉膛灭火boiler flame failure, boiler flame blackout259.稳定燃烧stable combustion260.压力容器pressure vessel261.支吊架supports and hangers262.原煤管道raw coal piping263.风道air duct264.热风道hot air duct265.冷风道cold air duct266.穿墙套管wall-through bushing, wall-bushing267.伸缩节expansion joint268.送粉管道pulverized coal feed piping269.燃油管道fuel oil piping270.风管道air piping271.一次风管道primary air piping272.二次风管道secondary air piping273.落粉管pulverized coal chute274.除灰管道ash piping275.烟道gas dust, gas pass276.尾部烟道convection flue gas pass277.煤气管gas piping278.连续排污管continuous blowdown piping279.烟囱chimney, stack280.多管式烟囱multi-flue chimney281.燃烧combustion282.四角喷射燃烧corner firing283.燃烧速度combustion rate284.机械未完全燃烧热损失heat loss due to mechanical incomplete combustion 285化学未完全燃烧热损失heat loss due to chemical incomplete combustion 286.灰渣热损失heat loss due to sensible heat in refuse287.排烟热损失heat loss due to flue gas288.散热损失heat loss due to radiation289.热损失heat loss290.火焰flame291.不稳定燃烧instable combustion292.负压燃烧balance draft combustion293.微负压燃烧pressurized combustion294.炉膛容积热负荷furnace volume heat release rate295.炉膛温度furnace temperature296.锅炉水循环boiler water circulation297.偏离泡核沸腾departure from nucleate boiling(DNB)298.水压试验hydraulic test299.汽水共沸priming300.点火ignition301.点火准备ignition preparation302.着火点firing point, ignition temperature303.折焰角nose304.飞灰fly ash305.煤粉细度fineness of pulverized coal306.灰ash307.灰的熔化点ash fushion temperature, ash fushion point, ash melting point308.可磨系数grindability index309.最大蒸发量maximum evaporation310.锅炉热平衡boiler heat balance311.超负荷运行overload operation312.正压positive pressure313.负压negative pressure314.理论空气量theoretical air quantity315.过剩空气量excess air quantity316.冷风cold air317.热风hot air318.除渣slag removal319.烟气flue gas320.锅炉上水boiler water filling321.蠕胀爆管tube burst due to creep322.汽包满水overfeed of water into drum323.锅炉灭火boiler fire extinction324.爆燃puff325.爆炸（外爆）explosion326.内爆implosion327.防爆anti-explosion328.煤粉自燃pulverized coal self-ignition, pulverized coalspontaneous combustion329.堵灰ash fouling330.堵煤coal jamming, coal plugging331.燃烧切圆firing tangential circle332.火焰中心flame center333.积粉pulverized coal deposits334.粉灰ash deposits335.飞灰可燃物combustibles in fly ash336.点火用油fuel oil for ignition337.飞灰腐蚀fly ash corrosion338.受热面heating surface339.辐射受热面radiation heating surface340.对流受热面convection heating surface341.尾部受热面rear heat recovery surface342.含氧量oxygen content343.蒸发量evaporation, evaporative capacity 344.切换风air switch-over345.煤耗率coal consumption rate346.入炉煤发热量heating value of the as fired coal 347.停炉boiler shutdown348.熄火fire-off349.灰水回收recovery of ash slurry water 350.细灰fine ash351.粗灰coarse ash352.干灰dry ash353.湿灰wet ash354.燃烧系数combustion system, firing system 355.制粉系统coal pulverizing system356.除灰系统ash handling system。
火电厂英语专业词汇
火电厂英语专业词汇acid cleaning 酸洗interstage leakage 级间漏汽coal bunker 原煤斗intevertion/disturbing/bump 扰动excess air 过量空气inverter 转换开关induced draft fan 引风机isolate 相互隔离steam drum 汽包item 物品、元件sub-distribution transformer 低压厂用变journal bearing 支持轴承6kv station board 6KV公用配电屏kilo-volt 千伏6kv unit board 6KV配电屏low pressure cylinder/casing(LP) 低压缸A: ampere 安培large scale integrate circuit 大规模集成电路actuator 执行机构LED 发光二极管adapter 转接器、接头、light/ignite 点火air circuit breaker 空气断路器linear variable differential transformer (LVDT)线性差动变压器air dry 分析基linearization 线性化air preheater 空气预热器liquid 液态air-insulated 空气绝缘的live steam 主蒸汽algorithms 算法load tap-changing 有载调压的2008.4.25alignment 平直度log 记录、日志alteration 改造longitudinal 纵向的alternating current 交流电lug 吊耳直流电？ammonia 氨major plant item 主要辅机amplitude 幅度making current 关合电流analogue 模拟量mal-function 误动作Analogue to Digital conversion 模数转换mechanism 操作机构annex 附属部分medium 媒介、介质annular 环状的membrane panel/wall 膜式壁annunciator 报警器micro-governor 微型调速器anthracite 无烟煤bituminous 烟煤mill 铁素体apex 顶点milli-volt 毫伏archive buffer 文件缓冲器Mimic 模拟图armature 电枢MMC: motor control center 电动机控制中心as received 应用基Modulation 调节、调制ash 灰分modulation-demodulation 调制解调ASM 模拟子模块moisture 水分At-temperator 减温器monitor mode 监控方式Automatic Boiler Controls 锅炉自动控制monitor/monitor unit 监控器automatic control system 自动控制系统monitoring 监测2008.4.26monoxide 一氧化碳auxiliary 辅助的motor starter 电动机启动装置axial 轴向的motor-operated 电动操纵的back-up 备用moving blades/ blading 动叶片bar 条形bar-graph 条形图Multi Function Process(MFP) 多功能处理器batch 成组的、成批的MVA: mega volt-ampere 兆伏安baud rate 波特率natural gas 天然气bay 隔间natural/thermal circulation 自然循环bearing house 轴承座network 电网bearing pad 轴瓦neutral point 中性点binary 二进制的nitrogen 氮binary cell 二进制单元node 节点binary counter 二进制计数器notch V形凹槽bit 比特、位ohm 欧姆oil 石油blank 毛胚oiled-cable 油浸式电缆blow 熔断open loop 开环blow/purge 吹扫open-cycle 开环blow-down pipe 排污管operation 运行/操作boil 沸腾operation condition 运行工况boiler/steam generator 锅炉optimum control 最优控制2008.4.27Boil out 煮炉breaking current 开断电流orientation 定位brown coal褐煤outage 停运bubble 汽泡outdoor 户外的burner 燃烧器outer casing 外缸bus interface module(BIM) 总线接口模块overhaul 大修busbar/bus 母线overhead 架空的cable 电缆overhead transmission line 架空输电线calibration 校验overview 全貌、总的看法capacitance 电容oxidized condition/atmosphere 氧化气氛capacitive current 电容电流oxygen 氧capacitor 电容器palm terminal 星型capacity 容量panel 配电盘、屏、板carbon 碳parallel interface 并行接口casting 锻造centerline 中心线peer 同类的central control room (CCR) 集控室permanent 长久的channel 通道、信道permanent magnet 永久磁铁charger 充电器PF burner/pulverized fuel burner 煤粉燃烧器chronological 按时间顺序的phase change 相变2008.4.28circuit breaker 断路器photo-electric 光电circular 圆形的pick-ups 采样器pilot exciter 副励磁机clearance 间隙pipe 管道closed loop 闭环plane 平面coal 煤plant-loop 厂环coal feeder 给煤机pneumatic pilot valve 启动控制阀coil 线圈power plant 电厂cold junction compensation 冷端补偿power station （水）电站power supply电源pressure 压力commissioning operation 试运行pressure firing 正压燃烧common service system 公用系统pressure meter 压力表compati-bility 兼容性、相容性probe 探针compatible 兼容的Process Control Unit (PCU) 过程处理单元complete functional set 全功能组件programmable logic controller(PLC) 可编程逻辑控制器programmable read only memory(PROM) 可编程只读存储器condensate 凝结prolong outage 长期停机2008.4.29conductance 导纳protection and trip 保护和跳闸conductibility 电导率provision 备用reserve 备用conductor 导体proximate analysis 工业分析cone 锥体PT: potential /voltage transformer 电压互感器configure 组态pulverizer/mill 磨煤机conical 圆锥形的push button 按钮connected in star 星型连接push contact 按钮触点consumption 消耗交流电alternating currentcontrol accuracy 控制精度control action 控制作用quality 质量control and instrumentation(C&I) 控制仪表系统quench 灭弧radial 半径的、辐射状的control console(desk) 控制台Rotor 转子controller 控制器reactance 电抗convection pass 对流烟道reaction turbine 反动式汽轮机converter 变送器rear end 后端、末端cooling fin 散热片rectify 整流coordination control system(CCS) 协调控制系统reducing condition/atmosphere 还原气氛core 铁芯redundancy 冗余的COIL线圈redundancy bit 冗余位crack/cracking 裂纹redundancy testing 冗余测试2008.4.30creep 蠕变reheater 再热器critical pressure 临界压力reliability 可靠性CT :current transformer 电流互感器reserve 备用resistance 电阻cylinder 汽缸resolution 分辨率cylindrical 圆柱形的reverse video 反相显示D.C. resistance 直流电阻roll 毛胚deaerator（D.A）除氧器roof tube 顶棚管decimal 十进制的root 叶根demineralized water 除盐水rotor 转子density 密度RTD 热电阻diaphragm 隔板stator 定子dielectric 不导电的、绝缘的saturated water 饱和水digit display 数字显示scheme: system 系统digit signal 数字信号screw 螺钉dimension 尺寸search coil 控制线圈diode 二极管semiconductor 半导体directed forced-oil and forced-air cooled(ODAF) serial access 串行存取disconnecter 隔离开关serial interface 串（行接）口discrete 不连续的serpentine tube 蛇形管2008.5.1distribute control system(DCS) 分散控制系统shadow 跟随distribution 配电shaft 轴diverter 分压器shroud/shrouding 围带division wall 分隔墙shunt 使分流double shell structure 双层缸结构shut down 停机double-flow 双向流动side wall 侧墙dowel 销钉signal conditioning 信号调节drain pipe 疏水管silicon 硅Drain 疏水single-flow 单向流动dry 干燥基slave module 子模块dry and ash free 可燃基Slipping 滑环dry -core cable 干式电缆Solenoid 电磁dual 双重的solid 固态duct 风道sootblower 吹灰器dump 转存sophisticated 高级的、先进的duodecimal 十二进制square root 平方根duplicate 复制的、备用的stabilization 稳定性duration 持续时间start up 启动dynamic stability 动稳定start up/standby transformer 启/备变eccentricity 偏心度state-of the-art 有目前发展水平的economizer 省煤器stationary blades/ blading 静叶片2008.5.2ECR:economic continuous rating 额定负荷stator frame 定子机座eddy current proximity detector 电涡流式检测器steady-state 稳态EHV :extra-high voltage 超高压steam air header 蒸汽热风器electric pressure converter 电压转换器steam/water vapor 水蒸气electrical equipment/apparatus 电气设备steam-water -mixture 汽水混合物electro-hydraulic 电动液压的stop/emergency valve 截止阀emergency 紧急的stress 应力energy 能量stud/stub 管接头engineering unit 工程单位sub system 子系统error checking and recovery 错误检验和恢复sub-bituminous 次烟煤error detector 错误指示器subcooled water 过冷水error rate 误差率substation 变电站evaluate 求出的数量suction firing 负压燃烧evaporate 蒸发suite 一组2008.5.3exception report 例外报告sulfur/sulphur 硫excite 励磁exciter 励磁机superconductor 超导体expansion 膨胀superheater 过热器expansion tank 油枕supervise 监督管理extinction 熄灭、灭火surge 浪涌surge diverter 避雷器facility 设备、工具switch block 开关组fatigue 疲劳、软化switch cabinet 开关柜feed back 反馈switcher 开关feeder speed 给煤机转速信号Switchgear 开关柜finish 光洁度symmetry 对称度synchronization 并网fixed carbon 固定碳tap 分接头flow meter 流量计tapping winding 分接头绕组flow rate 流量temperature 温度flue 烟道flue gas 烟气terminal 终端、端子forced draft fan 鼓风机terminal box 端子箱、出线盒forced/pumped circulation 强迫循环terminal device 终端设备the action of a magnetic field 磁场作用the control room 控制室2008.5.4frame 机座the dew point temperature 露点free standing 独立的front/rear wall 前/后墙the horizontal joint 水平接合面fuel /flue 燃料/烟道the operations panel 控制屏furnace 炉膛the top half 上半部furnace tube 水冷壁thermal efficiency 热效率fuse 熔断器thermal power plant 热电厂isolation 绝缘thermal stress analysis 热应力分析thermocouple 热电偶gaseous 气态gauge glass 水位计thermodynamic instrumentation 热工仪表generator 发电机thrust bearing 推力轴承generator transformer 主变tip 叶顶gland segment/packing 汽封片token 令牌tolerance 公差governor 调速器transformer 变压器gravity 重力transmitter 变送器grid 电网transport 传送、运输ground coal /pulverized fuel 粉状燃料transverse 横向的harmonious 协调的trap 阻波器header 联箱trip 切除、切断、脱扣heat 热量/加热tube 管子tube bundle 管排2008.5.5high pressure cylinder/casing(HP) 高压缸horizontal 水平的tubular 管形的hydraulic power plant 水电站turbine 汽轮机turbine supervisory instrument(TS) 汽机监视仪表hydrogen 氢turning gear 盘车装置hydrostatic test 水压实验two-tier terminals 双列端子排igniter 点火器impeller/wheel/disk 叶轮impulse turbine冲动式汽轮机Un-interrupt power supply(UPS) 不断电电源impulse withstand voltage 冲击耐受电压unit transformer 厂用变indoor 户内的utility boiler 公用锅炉inductance 感抗V: volt 伏特inductive 感应的vacuum contactor 真空断路器inductive current 电感电流Vane 导叶industrial boiler 工业锅炉Vertical 垂直的inner casing 内缸Via 经由Vibration 振动instrument 测试仪表visual (inquiry)display terminal 直观显示终端instrument board 仪器盘visual communication 可视通讯2008-5-6instrument correction仪表校正visual display unit (VDU) 直观显示元件instrument range 仪表量程visual frequency 视频instrument sensitivity 仪表灵敏度visual scanner 视像扫描器instrument terminal 端子、接线柱volatile 挥发分insulator 绝缘（isolation）子volt free contact 电压自由触点integration 使完整W: watt 瓦特interconnection 相互interface 接口water level 水位interlock 联锁wet-steam 湿蒸汽interlocking contact 联锁触点wind box 风箱interlocking signal 联锁信号winding 绕组interlocking switch system 联锁开关系统workhouse 模块intermediate pressure cylinder/casing(IP) 中压缸Zener diode 齐纳二极管/稳压二极管internally 内部的interruption 开断2008.5.7欢迎您的下载，资料仅供参考！。
火力发电厂英语词汇大全
电力英语一、锅炉部分1．临界压力锅炉supercritical pressure boiler2. 亚临界压力锅炉subcritical pressure boiler3. 超高压锅炉super-high pressure boiler4. 蒸汽锅炉steam boiler5. 蒸汽发生器steam generator6. 液态排渣锅炉wet bottom boiler7. 固态排渣锅炉dry bottom boiler8. 燃煤锅炉coal-fired boiler9. 燃气锅炉Gas-fired boiler10.燃油锅炉oil-fired boiler11.自然循环锅炉natural circulation boiler12.汽包（锅筒）锅炉drum boiler13.强制循环锅炉controlled circulation boiler14.直流锅炉once-through boiler15.复合循环锅炉combined circulation boiler16.旋风炉cyclone furnace boiler17.沸腾炉fluidized bed combustion(FBC)boiler18.循环硫化床circulating fluidized bed combustion(FBC)boiler19.增压循环硫化床锅炉 pressurized circulating fluidized bed combustion(PCFBC)boiler20.链条锅炉chain-grate boiler21.热水锅炉hot-water boiler22.废热（余热）锅炉water-heat boiler, heat recover steam generator(HRSG)23.启动锅炉start-up boiler24.厂用锅炉auxiliary boiler25.垃圾焚烧锅炉refuse-fired boiler, refuse incinerator27.露天锅炉outdoor boiler28.单炉膛锅炉single furnace boiler29.双炉膛锅炉twin furnace boiler30.W火焰锅炉W-flame boiler, vertical-fired boiler31.L火焰锅炉L-shape furnace boiler32.塔式锅炉tower boiler33.箱式锅炉box-type boiler34．炉墙furnace wall35. 汽包（锅筒）drum36.封头head37.汽包封头drum end plate, drum head38.下降管downcomer39.集中下降管centralized downcomer40.分散下降管distributed downcomer41.上升管riser42.管束（排）tube bundle43.管屏tube platen44.省煤器管economizer tube45.过热器管superheated tube46.再热器管reheater tube47.蛇形管coil48.吊挂管supporting tube49.引入管inlet pipe50.引出管outlet pipe51.饱和蒸汽管saturated steam pipe52.水冷壁管water wall tube53.鳍片管finned tube, fin tube, gilled tube54.内螺纹管rifled tube, grooved tube55.吸潮管moisture absorption piping56.水冷壁water wall57.膜式水冷壁membrane wall58.内螺纹水冷壁rifled tube water wall59.联箱header60.集汽联箱steam header61.卫燃带bailey wall, refractory belt62包墙管（包覆管）wall enclosure tube63.防渣管（弗斯顿管）slag screen, feston tube64.锅炉本体boiler proper65.锅炉机组boiler unit66.锅炉构架boiler structure67.炉膛boiler framework68.燃烧器furnace69.直流式燃烧器direct-flow burner70.旋流式燃烧器turbulent burner71.低NOX燃烧器low NOX burner72.摇摆式燃烧器tilting burner73.缝隙式燃烧器split burner74.燃烧室combustion chamber75.油枪oil gun torch76.风门damper77.一次风primary air78.二次风secondary air79.三次风tertiary air80.煤粉管道pulverized coal piping81.管板tube plate82.沸点boiling temperature83.过热器superheater84.前屏过热器front platen superheater85.后屏过热器rear plate superheater86.对流过热器convection superheater87.辐射过热器radiant superheater88.屏式过热器plate superheater89.顶棚过热器ceiling superheater90.包墙过热器wall enclosure superheater91.前包墙过热器front wall enclosure superheater92.后包墙过热器rear wall enclosure superheater93.侧包墙过热器side wall enclosure superheater94.吹灰器soot blower95.转动式吹灰器rotary soot bolwer96.伸缩式吹灰器retractable soot blower97.受热面积heating surface area, heat absorption area98.炉膛容积furnace volume99.炉膛热负荷furnace heat release rate, furnace heating absorption rate 100.汽水分离器steam separator, moisture separator101.起动分离器starting separator102.再循环管recirculating piping103.暖风器steam air heater104.再热器reheater105.再热器冷段primary reheater106.再热器热段final reheater107.顶棚ceiling108.省煤器economizer109.管式省煤器tube economizer110.管式空气预热器tubular air preheater111.回转式（再生式）空气预热器regenerative air preheater, rotary air preheater 112.板式空气预热器plate air preheater113.空气预热器air preheater114.三分仓空气预热器trisector regenerative air preheater115.漏风系数air leakage coefficient116.漏风率air leakage ratio117.漏风系统air leakage system118.漏风试验air leakage test119.安全门safety valve120.安全门开启压力opening pressure of safety valve121.安全门回座压力safety valve reseating pressure122.安全门压力整定试验pressure setting test of safety valve123.安全门动作压力safety valve operating pressure124.饱和蒸汽安全门saturated steam safety valve125. 过热蒸汽安全门superheated steam safety valve126.再热蒸汽安全门reheated steam safety valve127.防暴门explosion vent128.检查孔inspection hole129.事故喷水阀emergency water spray valve130.汽包事故放水阀emergency drum drain valve131.三通阀three-way valve132.反冲洗阀back wash valve133.取样阀sampling valve134.插板gate135.给水大旁路门feedwater overall bypass valve136.给水小旁路门feedwater individual bypass valve 137.大板梁plate girder, upper beam138.外护板outer casing139.锅炉排污blowdown140.定期排污扩容器intermittent blowdown flash tank 141.连续排污扩容器continuous blowdown flash tank 142.灰斗ash hopper143.冷灰斗bottom ash hopper, furnace hopper 144.混合器mixer145.齿圈（大牙轮）ring gear, geared ring146.空调器air conditioner147.空气压缩机air compressor148.给煤机coal feeder149.皮带式给煤机belt coal feeder150.刮板式给煤机scraper coal feeder151.叶轮式给煤机paddle coal feeder152.给粉机pulverizer coal feeder153.磨煤机coal pulverizer, coal mill154.钢球磨煤机tube mill155.中速辊式磨煤机roller mill, bowl mill, disk roll mill 156.双进双出钢求磨煤机double inlet and outlet tube mill 157.中速磨煤机medium speed mill158.风扇磨煤机beater wheel mill, beater mill159.排粉风机pulverized coal exhauster160.一次风机primary air fan161. 烟气再循环风机gas recirculation fan162.送风机forced draft fan, force fan163.引风机induced draft fan, induced fan164.离心风机centrifugal fan165.轴流风机axial-flow fan166.双速风机double speed fan167.轴流静叶可调风机adjustable static-blade axial-flow fanfixed pitch axial-flow fan168.轴流动叶可调风机adjustable moving-blade axial-flow fanvariable pitch axial-flow fan169.原煤斗raw coal bunker, raw coal silo 170.煤粉仓pulverized coal bunker171.输粉机pulverized coal conveyer172.刮板输粉机scraper pulverized coal conveyer 173.螺旋输粉机pulverized coal screw conveyer 174.粗粉分离器classifier175.细粉分离器（旋风分离器）cyclone separator176.锁气器air lock, flap177.减速机speed reduce178.看火孔observation hole179.人孔门man hole180.重油泵heavy oil pump181.重油加热器heavy oil heater182.汽-汽热交换器biflux183.煤气罐gas tank184.膨胀补偿节expansion joint185.直吹式制粉系统direct firing pulverizing system 186.中贮式制粉系统bin storage type pulverizing system 187.锅炉效率boiler efficiency188.锅炉热力计算boiler thermodynamic calculation 189.锅炉空气动力计算boiler aerodynamic calculation 190.锅炉水循环计算boiler water circulation calculation 191.锅炉水力计算boiler hydrodynamic calculation 192.锅炉强度计算boiler strength calculation193.锅炉热平衡boiler heat balance calculation 194.正平衡法direct balance method195.反平衡法indirect balance method196.过剩空气系数excess air coefficient197.排烟温度flue gas temperature198.单位蒸量specific evaporation199.低温腐蚀low temperature corrosion200.高温腐蚀high temperature corrosion201.结渣lagging202.结垢腐蚀deposit corrosion203.飞灰磨损fly ash erosion204炉膛负压furnace draft205.最高允许温度maximum permissible temperature 206.炉膛正压furnace pressure207.水循环water circulation208.循环倍率circulation ratio209.除尘器dust collector, precipitator210.静电除尘器electrostatic precipitator211.整流装置rectifying device212.锤打装置rapping gear213.含尘浓度dust loading concentration214.煤灰细度dust fineness215.除尘效率dust collection efficiency216.干式除尘器dry dust collector217.湿式除尘器wet dust collector, scrubber218.文丘里除尘器venture scrubber219.布袋除尘器fabric filter, bag house220.钢珠除尘装置shot-cleaning device221.水膜式除尘器centrifugal scrubber222.灰渣泵ash pump, slag pump223.轴封泵shaft sealing pump224.灰浆泵ash slurry pump225.除尘水泵dedusting pump226.回收水池water recovery pond227.清水池clean water pond228.灰浆池ash slurry pond229.油泵坑oil pump pit230.灰库ash silo231.灰场ash yard232.灰坝ash yard dam233.耐火砖firebrick234.保温材料heat-insulating material235.干式除灰（气力除灰）pneumatic pressure ash handling 236.水力除灰hydraulic ash handling237.正压气力除灰pneumatic pressure ash handling 238.负压气力除灰pneumatic pressure ash handling 239.仓式泵fluidizing transporter240.空气斜槽airslide, air gravity conveyor241.灰渣分除bottom and fly ash separate handling 242.灰渣混除bottom and fly ash mixed handling 243.灰渣利用bottom and fly ash recovery244.排渣槽bottom ash hopper245.埋刮板捞渣机submerged slag conveyor246.螺旋式捞渣机screw slag conveyor247.碎渣机clinker grinder, slag crusher248.振动筛vibrating screen249.稳燃器flame stabiliaer250.燃烧器蜗壳burner spiral case251.雾化器atomization252.机械雾化mechanical atomization253.蒸汽雾化steam atomization254.空气雾化air atomization255.气固两相流动gas-solid two-phase flow256.闭路循环closed cycle257.蒸汽带水carryoery258.炉膛灭火boiler flame failure, boiler flame blackout259.稳定燃烧stable combustion260.压力容器pressure vessel261.支吊架supports and hangers262.原煤管道raw coal piping263.风道air duct264.热风道hot air duct265.冷风道cold air duct266.穿墙套管wall-through bushing, wall-bushing267.伸缩节expansion joint268.送粉管道pulverized coal feed piping269.燃油管道fuel oil piping270.风管道air piping271.一次风管道primary air piping272.二次风管道secondary air piping273.落粉管pulverized coal chute274.除灰管道ash piping275.烟道gas dust, gas pass276.尾部烟道convection flue gas pass277.煤气管gas piping278.连续排污管continuous blowdown piping279.烟囱chimney, stack280.多管式烟囱multi-flue chimney281.燃烧combustion282.四角喷射燃烧corner firing283.燃烧速度combustion rate284.机械未完全燃烧热损失heat loss due to mechanical incomplete combustion 285化学未完全燃烧热损失heat loss due to chemical incomplete combustion 286.灰渣热损失heat loss due to sensible heat in refuse287.排烟热损失heat loss due to flue gas288.散热损失heat loss due to radiation289.热损失heat loss290.火焰flame291.不稳定燃烧instable combustion292.负压燃烧balance draft combustion293.微负压燃烧pressurized combustion294.炉膛容积热负荷furnace volume heat release rate295.炉膛温度furnace temperature296.锅炉水循环boiler water circulation297.偏离泡核沸腾departure from nucleate boiling(DNB)298.水压试验hydraulic test299.汽水共沸priming300.点火ignition301.点火准备ignition preparation302.着火点firing point, ignition temperature303.折焰角nose304.飞灰fly ash305.煤粉细度fineness of pulverized coal306.灰ash307.灰的熔化点ash fushion temperature, ash fushion point, ash melting point308.可磨系数grindability index309.最大蒸发量maximum evaporation310.锅炉热平衡boiler heat balance311.超负荷运行overload operation312.正压positive pressure313.负压negative pressure314.理论空气量theoretical air quantity315.过剩空气量excess air quantity316.冷风cold air317.热风hot air318.除渣slag removal319.烟气flue gas320.锅炉上水boiler water filling321.蠕胀爆管tube burst due to creep322.汽包满水overfeed of water into drum323.锅炉灭火boiler fire extinction324.爆燃puff325.爆炸（外爆）explosion326.内爆implosion327.防爆anti-explosion328.煤粉自燃pulverized coal self-ignition, pulverized coalspontaneous combustion329.堵灰ash fouling330.堵煤coal jamming, coal plugging331.燃烧切圆firing tangential circle332.火焰中心flame center333.积粉pulverized coal deposits334.粉灰ash deposits335.飞灰可燃物combustibles in fly ash336.点火用油fuel oil for ignition337.飞灰腐蚀fly ash corrosion338.受热面heating surface339.辐射受热面radiation heating surface340.对流受热面convection heating surface341.尾部受热面rear heat recovery surface342.含氧量oxygen content343.蒸发量evaporation, evaporative capacity 344.切换风air switch-over345.煤耗率coal consumption rate346.入炉煤发热量heating value of the as fired coal 347.停炉boiler shutdown348.熄火fire-off349.灰水回收recovery of ash slurry water 350.细灰fine ash351.粗灰coarse ash352.干灰dry ash353.湿灰wet ash354.燃烧系数combustion system, firing system 355.制粉系统coal pulverizing system356.除灰系统ash handling system电力英语二、汽轮机357.汽轮机steam turbine358.凝汽式汽轮机condensing steam turbine359.背压式汽轮机back pressure turbine360.抽汽式汽轮机steam extraction turbine361.中间再热式汽轮机reheating type steam turbine362.供热式汽轮机steam supply turbine, heat supply turbine, cogeneration turbine363.冲动式汽轮机impulse turbine364.反动式汽轮机reaction turbine365.轴流式汽轮机axial flow turbine366.辐流式汽轮机radial flow turbine367.单轴汽轮机tandem compound turbine, single-shaft turbine368.双轴汽轮机double-shaft turbine, cross compound turbine369.前置式汽轮机topping turbine370.燃气轮机gas turbine371.高压汽轮机high pressure turbine372.中压汽轮机medium pressure turbine373.低压汽轮机low pressure turbine374.超高压汽轮机ultra pressure turbine375.亚临界压力汽轮机subcritical pressure turbine376.超临界压力汽轮机supercritical pressure turbine377.空冷式汽轮机组air cooled turbine unit378.燃气轮机组（装置）gas turbine unit379.高压汽缸high-pressure(HP) cylinder380.中压汽缸intermediate-pressure(IP) cylinder381.低压汽缸low-pressure(LP) cylinder382.内汽缸inner casing383.外汽缸outer casing384.上汽缸upper casing385.下汽缸lower casing386.汽缸法兰螺栓加热装置cylinder flange heating appliance387.汽缸台板（底板）cylinder sole pin388.汽缸猫爪cylinder claw389.滑销sliding pin390.横销traverse pin391.纵销longitudinal pin392.立销vertical pin393.定位销aligning pin, locating pin394.汽轮机转子turbine rotor395.叶轮 impeller396.叶片blade,397.动叶片moving blade398.静叶片stationary blade399.叶根型式type of blade root400.末级叶片长度length of last stage blade401.喷嘴室nozzle box402.末级叶片强度last stage blade stress403.排汽室steam exhaust hood404.喷嘴nozzle405.围带shroud ring406.拉筋（拉金）lacing wire407.平衡块balance weight408.固定螺钉dowel409.隔板diaphragm410.隔板套diaphragm sleeve411.隔板汽封diaphragm seal, diaphragm sealing412.汽封steam seal gland, steam sealing413.迷宫式汽封labyrinth seal414.梳齿式汽封serrate-type steam seal415.汽封套seal bushing416.汽封块seal block417.汽封齿seal tooth418.轴承支架bearing stoll, bearing bracket419.主轴承箱main bearing box420.滚珠轴承ball bearing421.滚柱轴承roller bearing422.滑动轴承sliding bearing423.推力轴承thrust bearing424.止推环thrust collar425.瓦枕bearing pillow426.锁饼lock427.推力瓦块thrust bearing pad428.主油泵main oil pump429.备用油泵emergency bearing oil pump430.调速油泵regulation oil pump, speed governing oil pump 431.交流润滑油泵AC lube oil pump432.直流润滑油泵DC lube oil pump433.注油器oil injector434.同步器synchronizer435.同步器手轮synchronizer hand wheel436.控制滑阀pilot valve437.随动滑阀servo-valve438.分配滑阀distributing pilot valve, distributor valve439.中间滑阀intermediate valve440.微分器differentiator441.功率限制器load limiter442.动态校正器dynamic corrector443.滑阀套valve sleeve444.喷油嘴oil nozzle445.弹性调速器flexible governor446.调速器挡块governor stop447.危急遮断器滑阀emergency trip pilot valve448.撞击子ram449.防火滑阀fire protection pilot valve450.延滞滑阀delay pilot valve451.跟踪滑阀follow-up pilot valve452.电-液转换器electro-hydraulic converter, electro-hydraulic transducer 453.切换滑阀change-over pilot valve454.危急保安器emergency governor455.危急保安器滑阀emergency governor pilot valve456.超速试验滑阀overspeed test pilot valve457.喷油试验滑阀nozzle test pilot valve458.反馈滑阀feedback pilot valve459.起动排油阀oil drain valve at star-up460.紧急放油阀emergency oil relieve valve461.排油口oil diacharge outlet462.节流滑阀throttle pilot valve463.滑动油阀movable pilot valve464.高压自动关闭器high-pressure automatic closing gear465.中压自动关闭器medium pressure automatic closing gear466.高压油动机（高压伺服马达） high-pressure hydraulic actuator, high-pressure servo-motor467.中压油动机medium-pressure hydraulic actuator, medium-pressure servo-motor468.杠杆lever469.轴shaft470.主轴main shaft471.传动轴(主动轴) driven shaft472.被动轴（从动轴）driven shaft473.小轴axle474.联轴器coupling475.刚性联轴器rigid coupling476.半挠性联轴器semi-flexible coupling477.齿型联轴器serrated coupling478.冷油器oil cooler479.溢油器oil overflow valve480.排油烟机oil-fume extractor, oil fume exhaust 481.油烟分离器oil-fume separator482.油净化器oil purifier, oil conditioner483.过滤罐filtering tank484.布袋式过滤器bag filter, fabric filter485.齿轮油泵gear oil pump486.顶轴油泵jacking oil pump487.柱塞式油泵piston type oil pump488.螺杆式油泵worm type oil pump489.盘车装置turning gear490.盘车手轮turning gear hand wheel491.化桩板lagging enclosure492.齿轮gear493.直齿式齿轮spur gear494.斜齿式齿轮helical gear495.伞型齿轮bevel gear496.蜗轮worm wheel497.蜗杆worm stem498.弹簧spring499.密封油箱sealing oil tank500.空气侧交流密封油泵air side AC sealing oil pump 501.空气侧支流密封油泵air side DC sealing oil pump 502.压差阀differential pressure valve503.平衡阀balancing valve504.密封瓦sealing pad505.缓冲油箱buffer oil tank506.高位油箱head oil tank, elevated oil tank 507.事故油箱emergency oil tank508.磁性过滤器magnetic filter509.发电机内冷水箱generator inner cooling water tank 510.发电机内冷水泵generator inner cooling water pump 511.离子交换器ion exchanger512.干燥器dryer, drier513.冷凝式干燥器condensing type drier514.凝汽器condenser515.多压式凝汽器multi-pressure condenser516.单流程凝汽器single-pass condenser517.双流程凝汽器double-pass condenser518.黄铜管brass tube519.管板tube plate520.凝汽器喉部condenser throat521.热水井hot well522.凝结水泵condensate pump523.泵壳pump casing524.盘根gland packing525.盘根压盖gland top cover526.盘根端盖gland end cover527.填料packing528.轴封抽汽风机shaft seal extraction fan529.轴封抽汽冷却器shaft seal extraction cooler, gland cooler530.轴封漏汽加热器shaft seal leakage heater531.低压加热器low-pressure feed water heater532.中压加热器media-pressure feed water heater533.高压加热器high-pressure feed water heater534.蒸汽冷却器steam cooler535.疏水冷却器drain water cooler536.汽侧steam side537.水侧water side538.U型管U-tube539.除氧器deaerator540.储水池water storage pond541.卧式除氧器horizontal type deaerator542.立式除氧器vertical type deaerator543.喷雾式除氧器atomizing type deaerator544.淋水盘water spraying tray, sprinkling tray545.除氧水箱deaerated water tank546.稳压水箱surge water tank, stabilizing water tank547.除盐水箱demineralized water tank548.除盐水泵demineralized water pump549.汽动给水泵steam-driven feed water pump550.电动调速给水泵motor-driven variable speed feed water pump551.前置水泵booster pump552.给水泵feed water pump553.机械密封mechanical seal554.碳精密封环carbon seal ring, carbon packing ring555.动环moving ring556.静环static ring557.平衡盘balancing disc558.液力偶合器hydraulic coupler559.泵轮（主动轮）pump impeller, driving impeller560.涡轮（从动轮）whirling impeller, driven impeller561.勺管scoop tube562.辅助油泵auxiliary oil pump563.疏水泵drain pump564.疏水扩容器drain flash tank565.疏水箱drain tank566.热网加热器heater for heating network, heating network hot water heater567.生水加热器raw water heater568.热网水泵pump for heating network, heating network hot water pump 569.生水泵raw water pump570.除尘水泵pump for scrubber, scrubber water pump571.壳体case, shell572.水室water chamber573.封头end cover574.挡板baffle plate575.导流板guide plate576.射水泵water jet pump577.真空泵vaccum pump578.射水抽气器water jet air ejector579.射汽抽气器steam jet air ejector580.射水池water jet pond581.排水池drain water pond582.工业水泵industrial water pump, service water pump583.排污泵blowdown pump584.轴流泵axial flow pump585.清水泵clean water pump586.污水泵sewage pump587.排水泵water discharge pump588.立式深井泵vertical deep-well pump589.深井泵deep-well pump590.潜水泵submerged pump591.循环水泵circulating water pump592.清污机trash remover593.混流泵mixed flow pump594.离心泵centrifugal pump595.旋转滤网rotating type screen, screw type strainer596.胶球泵rubber ball recirculating pump597.收球网ball screen598.装球网ball collector599.管式冷却器tubular cooler, tube type cooler599/1.支撑斜钢supporting wedge600.板式冷却器plate type cooler601.冷却水池cooling water pond602.喷水池spraying water pond603.冷却水塔cooling tower604.自然通风冷却塔natural draft cooling tower605.逆流式冷却塔reverse flow cooling tower606.横流式塔transverse flow cooling tower607.机力通风冷却塔mechanical draft cooling tower608.空气冷却塔air cooling tower609.干式冷却塔dry cooling tower610.分水槽water diversion channel611.竖井shaft, well612.闸板井gate well613.闸门室gate chamber, gate house614.挡风板air baffle plate615.新（主）蒸汽管道main steam piping, live steam piping 616.主蒸汽系统main steam system617.再热蒸汽系统reheat steam syetem618.抽汽系统extraction steam system619.轴封供汽系统shaft seal steam supply system620.轴封shaft seal shaft gland621.门杆漏汽系统valve lever leakage steam system622.汽缸法兰螺栓加热系统casing flange and bolt heating system 623.真空系统vaccum system624.凝结水系统condensate system625.再热蒸汽管道reheat steam system626.给水系统feed water system627.循环水系统circulating water system628.工业水系统industrial water system, service water system 629.供油系统oil supply system630.密封油系统seal oil system631.厂用蒸汽系统auxiliary steam system632.调速系统speed governing system633.电液调速系统electro-hydraulic speed governing system 634.发电机内冷水系统generator inner cooling water system 635.热网系统heating network system636.导汽管steam lead pipe637.连通管inter-connecting pipe638.抽汽管道steam extraction pipe639.抽汽母管steam extraction header640.厂用蒸汽管道plant service steam piping641.厂用蒸汽母管plant service steam header642.蒸汽旁路系统steam bypass system643.蒸汽大旁路single stage steam bypass644.一级蒸汽旁路first stage steam bypass645.二级蒸汽旁路second stage steam bypass646.辅助蒸汽母管auxiliary steam header647.供汽联箱steam header648.回汽联箱return steam header649.供水联箱water supply header650.回水联箱return water header651.门杆漏汽管道valve lever steam leakage piping652.轴封漏汽管道shaft seal leakage steam piping653.抽空气管道air extraction piping654.压缩空气管道compressed air piping655.氢气管道hydrogen piping656.疏水管道drain water piping657.凝结水管道condensate piping658.循环水管道circulating water piping659.工业水管道industrial water piping, service water piping 660.冷却水管道cooling water piping661.给水管道feed water piping662.除盐水管道demineralized water piping663.减温水管道attemperating water piping664.再循环水管道recirculating water piping665.排水管道water discharge piping666.润滑油供油管道lube oil supply piping667.润滑油管lube oil piping668.调速油管governing oil piping669.回油管道return oil piping670.压力油管道pressure oil piping671.密封油管道seal oil piping672.脉动油管pulsating oil piping673.热网水管道heating network water piping674.平衡管balance pipe675.电动主闸门motor-operated main gate valve676.高压主汽门high-pressure main stop valve677.中压主汽门intermediate pressure main stop valve 678.旁路门bypass valve679.防腐汽门corrosion-proof valve680.高压调速汽门high-pressure governor valve681.中压调速汽门medium pressure governor valve682.对空排汽门atmospheric relief valve683.疏水门drain valve684.调整门adjusting valve685.电动门motor-operated valve686.手动门hand-operated valve687.减温器attemperator, desuperheater688.减压器（阀）pressure reducer(valve)689.减温减压器temperature and pressure reducer690.抽汽电动门motor-operated steam extraction valve 691.抽汽逆止门extraction check valve692.高压排汽逆止门high-pressure exhaust check valve 693.逆止门check valve, non-return valve694.入口门inlet valve695.出口门outlet valve696.球型阀globe valve697.闸板阀gate valve698.针型阀needle valve699.翻板阀tripper valve700.液压阀hydraulic valve701.控制阀control valve702.换向阀reverse flow valve703.疏水阀drain valve704.蝶阀butterfly valve705.衬胶门rubber lined valve706.高压加热器入口联成阀composite valve at high pressure heater inlet 707.高压加热器出口联成阀composite valve at high pressure heater outlet 708.高压加热器旁路门high pressure heater bypass valve709.水封阀门water seal valve710.排污门blow down valve711.排气门exhaust steam valve712.排汽门exhaust steam valve713.补水门water supply valve, make-up water valve714.补油门oil valve, oil supply valve715.补氢门hydrogen supply valve716.空气门air valve717.真空破坏阀vacuum breaking valve, vacuum breaker718.排汽安全门exhaust steam safety valve719.弹簧安全门spring relief valve720.排汽缸喷水门exhaust cylinder water-spraying valve721.电磁阀solenoid valve, magnet valve722.前截门front intercept valve723.后截门rear intercept valve724.排氢门hydrogen vent valve725.中间抽头门intermediate stage bleed-off valve726.最小流量阀minimum flow valve727.暖泵门pump warming valve728.泵体放水门pump-body water drain valve729.放水门water discharge valve730.减温水门attemperating water valve731.切换门change-over valve, diverting valve732.联络门interconnection valve733.液压逆止门hydraulic check valve734.再沸腾加热门reboiled heating valve735.放空气门air vent valve736.再循环门recirculation valve737.冷却水门cooling water valve738.热效率thermal efficiency, heat efficiency739.内效率internal efficiency740.额定工况rated operation condition741.最大工况maximum operation condition742.汽耗量steam consumption743.汽耗率steam consumption rate744.热耗率specific heat consumption, heat rate745.新蒸汽压力initial steam pressure, live steam pressure746.再热蒸汽冷段压力cold reheated steam pressure747.再热蒸汽热段压力hot reheated steam pressure748.再热蒸汽热段温度hot reheated steam temperature749.再热蒸汽冷段温度cold reheated steam temperature750.主蒸汽流量steam flow751.再热蒸汽流量reheated steam flow752.低压缸排汽流量low-pressure cylinder exhaust steam flow753.转速rotating speed, revolution754.真空度vaccum755.旋转方向rotation direction756.给水温度feedwater temperature757.调节级压力pressure at velocity stage758.临界转速critical speed759.吊装重量lifting weight760.速度变化率speed variation rate761.迟缓率delay rate762.凸轮转角cam torque angle763.过热度superheat degree764.温差temperature difference765.端差terminal temperature difference766.过冷度supercooling degree767.高压加热器投入率high pressure heater availability rate768.轴向位移axial shift, axial displacement769.大轴晃动值shaft swinging value, shaft eccentricity770. 高压缸膨胀high-pressure cylinder expansion771.中压缸膨胀intermediate pressure cylinder expansion772.低压缸膨胀low pressure cylinder expansion773.市政速油压governing oil pressure774.润滑油压lubricating oil pressure775.脉动油压impulse oil pressure776.附加保安油压additional safeguard oil pressure777.滑阀上油压oil pressure above pilot valve778.滑阀下油压oil pressure under pilot valve779.润滑油温lubricating oil temperature780.轴承加油温度bearing return oil temperature781.轴承钨金温度babbit metal temperature, bearing metal temperature 782.推力瓦块温度thrust pad temperature783.密封油压seal oil pressure784.油位oil level785.水中含氧量oxygen content of water786.凝结水硬度condensate hardness787.轴承振动值shaft(bearing) vibration amplitude788.垂直振动值vertical vibration amplitude789.水平振动值horizontal vibration amplitude790.轴向振动值axial vibration amplitude791.油膜振荡oil film oscillation, oil whipping792.冲转impulse starting793.冷态启动cold start794.热态启动hot start795.滑参数启动starting at sliding parameters, sliding pressure starting 796.滑参数停机shut-down at sliding parameters, sliding pressure shut-down 797.升速speed up798.升速率percentage of maximum momentary speed variation,speed-up rate799.负荷上升率loading rate800.基本负荷base load801.调峰运行peak load regulating operation, cyclic operation802.空转idling, idle running803.手动打闸停机hand trip, turbine hand trip804.暖机turbine warming up805.最短盘车时间minimum turning time806.低速暖机low speed warming807.中速暖机medium speed warming808.滑参数起动曲线starting curve at sliding parameters,sliding pressure starting-up curve809.滑参数停机曲线shut-down curve at sliding parameters,sliding pressure shut-down curve810.全周进汽full admission811.部分进汽partial admission, partial-arc admission812.喷嘴调节nozzle governing813.节流调节throttle governing814.破坏真空vaccum breaking815.汽缸金属温度cylinder metal temperature816.听音检查sound detection817.惰走时间idling time818.超速试验overspeed test819.真空严密性试验vaccum leakage test820.主汽门严密性试验main steam stop valve leakage test821.危急遮断器充油试验emergency governor oil filling test822.低油压保护试验low oil pressure protection test823.调速系统静止试验governing system pre-operation test824.调速系统动态特性试验governing system dynamic performance test825.调速系统静态特性试验governing system static performance test826.甩负荷试验load-dump test, load-rejection test827.空负荷试验no-load test828.满负荷试验full-load test829.超负荷试验overload test830.转子平衡试验rotor balancing test831.动平衡dynamic balancing832.静平衡static balancing833.热力试验thermodynamic test834.叶片频率试验blade frequency test 835.投入运行to be put into operation 836.开启opening837.关闭closing838.启动starting-up839.停止shutting down840.充氢hydrogen charging841.排氢hydrogen discharging842.补水water make-up843.补油oil make-up844.水位调整water level regulation 845.暖管warming846.手摇同步器hand synchronizer847.检查inspection, examination 848.巡检routing inspection849.蒸汽带水carry-over850.水击hydraulic shock, water hammer 851.超速overspeed852.轴承损坏（烧瓦）bearing burnt-out853.断叶片broken blade854.断轴broken shaft855.气蚀cavitation856.反转（倒转）reversal rotation857.调节级regulation stage858.压力级pressure stage859.抽真空vaccum extraction860.盘车turning861.法兰加热flange heating862.螺栓加热bolt heating863.漏汽steam leakage864.漏水water leakage865.炭精轴封carbon packing866.冒烟smoking, smoke belching 867.着火fire catching, fire868.强烈振动strong vibration869.管道破裂piping breaking870.无蒸汽运行no-steam operation。
火电厂常用英语词汇总结
火电厂常用英语词汇总结注：以下内容为根据实际工作经验总结的常用词汇，不求专业,但求实用。
火电厂组成堆取料机Stacker —reclaimer斗轮机Bucket wheel machine吹灰器soot blower省煤器Economizer除氧器deaerator汽轮机steam turbine高压缸HP cylinder/casing中压缸IP cylinder/casing低压缸LP cylinder/casing发电机electric generator锅炉boiler炉膛furnace二次风机secondary air fan一次风机primary air fan引风机induced draft fan送风机forced draft fan加热器heater再热器reheater过热器superheater空气预热器air preheater燃烧器burner空压机air compressor给水器water feeder冷凝器condenser凝结水condensate water凝结水泵condensate pump静电除尘器electrostatic precipitator(ESP）变电站substation变压器transformer励磁机exciter输煤机coal conveyor转运站transfer tower碎煤机coal crusher磨煤机pulverizer干煤棚coal shed除渣系统slag handling system除灰系统ash handling system飞灰flyash灰库ash silo循环流化床CFBC（circulating fluidized bed combustion) 油箱diesel fuel tank灰斗ash hopper煤仓间coal bunker汽包steam drum给煤机coal feeder旁路系统bypass system制氯间electrolytic chlorine house泡沫消防间foam fire-fighting room变频器室frequency converter room化粪池septic tank车辆调度中心motor pool化学药品仓库chemical storage house转运站transfer tower灰场ash pond冷却塔cooling tower工程土建类螺丝screw螺丝刀screw—driver螺母/螺帽nut螺栓bolt垫圈gasket/washer锤子hammer扳手wrench老虎钳plier/vice切割机/砂轮机grinder/sander砂纸emery paper/sand paper麻袋sack铁锹shovel/spade喷枪spray gun零部件components焊接weld电焊工electrical welder铆工riveter钳工benchworker管工/水暖工plumber瓦工mason砌筑masonry推土机/推煤机bulldozer铲车loader板车handcart挖掘机backhoe/excavator搅拌机mixer搅拌站batching plant叉车forklift truck吊车crane/hoist电动葫芦electric hoist龙门吊gantry crane轮胎tire配重counterweight压路机road roller油罐车oil tank truck脚手架scaffolding枕木sleeper/cushion三合板three—ply board称scale热熔器heater地漏floor drain雨棚rainshed/canopy/rain shelter 铁丝网wire mesh带刺铁丝barbed wire刀刺网（铁圈形）combat wire夯实compact振动棒/振捣器vibrator减震平台vibration absorber钢筋steel bar钢板steel plate槽钢channel steel镀锌扁铁galvanized flat steel钢筋混凝土reinforced concrete 碎石gravel沥青asphalt砂浆mortar石膏板plasterboard石灰石limestone空心砖hollow block/brick焦石料coke stone瓷砖ceramics/tile底漆primer/undercoat安装installation建造erection装配fabrication/assemble支模，拆模form work卸货unload/discharge拆take apart/ disassemble模具mould/mold打桩piling work回填backfill窗户铁栏杆window metal grill保温层heat preservation/insulation layer 路肩shoulder路堤embankment地基foundation基床bedding地下室basement排水沟drainage ditch化粪池septic-tank/digestion tank隧道tunnel涵洞culvert码头jetty/pier/dock/wharf挡土墙retaining wall路缘curb绿化landscaping护坡slope protection滑坡landslide通风Ventilation格构waffle停机坪helipad省道provincial road铺砌pavement梁beam柱column漏水leakage直径diameter半径radius标高elevation宽度width地震带seismic belt门廊（门前小屋檐）porch隔墙partition风道air duct天花板ceiling百叶窗louver/shutter/blind瞭望塔watching tower/tower sentry集水坑sump pit污水sewage/wastewater细骨料fine aggregate粗骨料coarse aggregate钻孔drilling铸造/浇筑casting围网perimeter fence隔离网seclusion fence油漆涂料类粘合剂bonding joint面漆finishing coat/topcoat稀释剂thinner催化剂catalyst防腐剂preservative玻璃胶silicon sealant抹灰plastering灌浆/灰浆grout粘合剂/胶adhesive树脂resin自流平self-levelling裂缝crack腻子putty刮刀scraper刮scrape石膏gypsum修琢打毛chip针needle/pin刺n. thorn刺V。
发电站专用英语词汇
flue：烟道boiler：锅炉ESP: electrostatic precipitator 静电除尘器electrostatic dust catcherfield：磁场ductwork：风管管网bellow:风箱duct：烟道GCV (kcal/kg): 总热值BFG: blast furnace gas高炉煤气FC（fixed carbon）:固碳Ash：灰分Volatile matter：挥发分Coal analysis：碳质分析Design coal:设计煤种Proximate analysis：近似分析Ultimate analysis:元素分析circulating fluidized bed:循环式流体化床membrane wall：膜式水冷壁furnace:熔炉drum:汽包，锅筒ignition system：点火系统combustion chamber:燃烧室air feed:送气,供气calorific value：热值economizer：省煤器布置在锅炉尾部烟道内加热给水的部件super-heater：过热器waste heat boiler：废热锅炉（根据场合不同，可以分为电站废热锅炉和化工废热锅炉）pulverized coal fired boiler: 煤粉燃烧锅炉MSW incineration boiler：城市固体废物燃烧锅炉Coal-mud boiler：煤泥锅炉Head：封头Header：联箱water—cooling vibrating stoker：水冷振动炉排bio-mass fired boiler：生物燃烧锅炉grate：炉排steam drum:汽包锅炉汽包有什么作用？答:(1)汽包与下降管、上升管连接组成自然循环回路，同时汽包又接受省煤器来的给水，还向过热器输送饱和蒸汽,所以汽包是锅炉内加热、蒸发、过热这三个过程的连接枢纽。
（2)汽包中存有一定的水量，因而有一定的储热能力，这些可以提高运行的安全性. (3)汽包中装有汽水分离装置，蒸汽冲洗装置，连续排污装置，炉内加药装置等以改善水汽品质。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Vocabulary on Power Generation(Thermal Power Plant)火电厂常用专业词汇1. stop valve/non-return valve(NRV)/check valve 截止阀；逆止阀, 单向阀2. reverse valve 倒流阀3. cylinder holding 闷缸4. (cylinder)heat soaking 暖缸5. boiler hot boxup 闷炉6. boiler warm-up 暖炉7. axial thrust/stress 轴向推力8. axial shift/displacement 轴向位移9. radial displacement 径向位移10. emergency stop valve(ESV) 危急遮断阀11. steam lead pipe 导汽管12. valve body/casing 阀体，阀壳13. synchronization (with power grid) 并网14. inlet shut-off valve 进油关断阀15. flame scanner/detector 火检16. scanner fan 火检风机17. BCP: Boiler Circulation Pump 炉水循环泵18. slag remover 除渣机19. slag conveyor 捞渣机20. rotary vane feeder(RVF) 螺旋输送机（除灰站）21. ECS：electric control system 电气控制系统22. ETS: emergency trip system 汽机紧急跳闸系统23. hydraulic station 液压油站24. vent/ventilation valve(V.V) 排气阀、通风阀25. ESP : Electro-Static Precipitator 静电除尘器；电除尘26. dedust transformer 电除尘变27. control valve 调阀、调门28. pilot/slide valve 滑阀29. steam header 集汽联箱30. water filling （锅炉等）上水31. bearing pillow 瓦枕32. bush 轴瓦33. forward/positive reverse/negative thrust bearing 正/负向推力轴承（瓦块）34. atmospheric/top relief valve 对空排气阀35. exhaust(gas) fan, oil vapor exhaust fan OVEF 排烟风机36. operating transformer/O.X/OPER._.FMR 工作边37. FGD: Flue Gas Desulphurization(desulfurize/ desulphurize) 烟气脱硫38. anion 阴离子39. cation 阳离子40. anion/cation bed/exchanger 阴、阳离子交换器；阴床、阳床41. cathode阴极42. anode 阳极43. cathode axis 阴极磁轴44. caustic/acid storage tank 碱储存罐，酸储存罐45. resin dosing hopper 树脂加装斗46. CRT, cation resin regeneration tank and water storage tank阳塔, 阴（树脂）再生罐兼储水罐ART, anion resin regeneration tank 阴塔，阴（树脂）再生罐SPT, resin separation tank（树脂再生）分离塔47. MEH: micro-hydraulic control 微机电液控制48. TSI: turbine supervision instrument 汽机监视仪表49. chemical dosing 化学加药50. back wash 反洗51. AGC: Automatic Gain Control 自动增益控制Automatic Generation Control 自动发电控制（一般取此义）52. ATC: Automatic Turbine Startup or Shutdown Control System 汽机自启停系统53. BPS: Bypass Control System 旁路控制系统54. CCS: Coordination Control System 单元机组协调控制系统55. DAS : Data Acquisition System 数据采集系统56. DCS: Distributed Control System 分散控制系统57. DEH: Digital Electro-Hydraulic Control （汽机）数字电液控制系统58. ETS: Emergency Trip System （汽机）事故跳闸系统59. FSSS: Furnace Safety Supervisory System 锅炉炉膛安全监控系统60. MCS: Modulation Control System 模拟量控制系统61. MFT: Master Fuel Trip 主燃料跳闸62. OFT: Oil Fuel Trip 油燃料跳闸63. OPC: Over-Speed Control （汽机）超速保护控制64. SCADA: Supervisory Control and Data Acquisition 监控与数据采集系统65. SCS: Sequence Control System 顺序控制系统66. TSI: Turbine Supervisory Instrument （汽机）监视仪表67. jacking oil pump 顶轴油泵68. OEM: Original Equipment Manufacturer 设备原产商；厂代、工代69. installed capacity 装机容量70. thermal stress 热应力71. main valve of desuperheating/spray water 减温水总门72. TD-BFP/MD-BFP: Turbine-Driven/Motor-Driven Boiler FeedwaterPump汽动给水泵、汽泵；电动给水泵、电泵73. emergency governor 危急保安器74. auxiliary power system 厂用电系统75. PCV: pressure control valve 压力控制阀76. MCC: motor control center 电机控制中心77. walkie-talkie 对讲机；步话机78. mis-operation 误操作79. shift-in-charge/shift chief-operator 值长80. SCE: shift chief engineer 当值总工程师81. meet/satisfy a condition 满足条件82. supervisor 运行监护人员83. field operator 巡操84. operation/operating floor 运转层85. operation log 运行日志86. force(certain value) 强制（某个数值，如温度、压力等）87. take/put into/in service/operation 投运、投用88. reading （仪表等的）读数89. signal is extended/connected to DCS 信号传至DCS90. work permit/permit to work 工作票91. operation checklist 操作票92. bearing burnt-out 轴承烧坏93. emulsion 乳化94. anti-emulsification time 破乳化时间95. servo valve/motor 伺服阀；伺服电机96. hydraulic servomotor; oil relay 油动机97. HP/LP bypass 高压旁路、低压旁路98. PAC 临时完工证书99. EPC: engineering-procurement-construction “设计-采购-安装”总承包工程100. d efect maintenance/rectification；rectifying defect/remove defect 消缺101. a ttend 处理故障、缺陷等102. d efect register 缺陷登记/统计103. periodic maintenance 定期维修104. preventive maintenance(PM)预防性维修105. coupling/coupler 联轴器，耦合器106. hydraulic coupler 液耦107. speed reducer 减速器108. dismantle 拆除109. install, installation; erect, erection 安装110. boxup 在印度TPCIL常用来表示某项工作已经完成，封闭111. operator console 控制台112. AHP: ash handling plant 除灰站，输灰站113. GIS: gas insulated switchgear 气体绝缘开关设备；升压站114. CHP：coal handling plant 输煤站115. WTP：water treatment plant 制水站116. rubber ball circulating pump 胶球（再循环）泵117. ball cleaning system; condenser online tube cleaning system 凝汽器胶球清洗系统118. ball screen 收球网119. ball collector 收球器120. condenser online tube leakage system 凝汽器检漏系统121. clarifying basin 澄清池122. settled water 澄清水123. blow-down flash tank 排污扩容器124. condensate extraction pump(CEP) 凝结水泵，凝泵125. VFD: Variable-Frequency Drive 变频器126. valve opening 阀门开度127. (water)intake pipe 进水管128. skilled worker 熟练工人；技工129. inter-lock/open/close 联锁、开、关130. Interlock protection 联锁保护131. air/steam supply 气源，汽源132. power(supply) 电源，供电133. grease n. 油脂；润滑脂v.给……上油脂134. calcium complex grease 复合钙基脂135. operating mode 运行方式136. screw pump 螺旋泵137. oil return 回油138. ash/oil deposits/accumulation 积灰；积油139. gland steam condenser 轴封加热器140. ash hopper heater 灰斗加热器141. collecting electrode rapping mechanism(CERM) 阳极振打装置142. emitting electrode rapping mechanism (EERM) 阴极振打装置143. booster pump 前置泵；增压泵144. minimum flow valve 最小流量控制阀145. drain flash tank 疏水扩容器146. vacuum pulling 抽真空147. valve block 阀组148. valve seat 阀座149. valve stem 阀杆150. valve wide open condition(VWO) (condition) 阀门全开工况151. valve packing 阀门盘根152. valve travel 阀门行程153. governing/control stage 调节级154. primary/final reheater; CRH/HRH 冷再；热再155. rolling(up) 冲转156. swinging value 晃动值157. eccentricity 偏心率，晃动度158. vibration amplitude 振动值159. high vibration 振动大160. differential expansion 胀差161. cylinder expansion 缸胀162. MSP（汽机）启动油泵163. EOP（汽机）事故油泵164. TOP（汽机）辅助润滑油泵165. motor-operated valve(MOV) 电动阀，电动门166. increased/decreased load ratio 升/降负荷率167. loading rate 升负荷速度，升荷率168. pressure rise; raise/increase pressure 升压169. runup rate 升速率170. speed up/accelerate 升速171. run up（RU）; run down(RD) 升负荷；降负荷172. fast cut back（FCB）快速切负荷173. run back（RB）快速减负荷174. block increase/decrease 闭锁增BI；闭锁减BD175. idle running 惰走，空转176. carbon brush 碳刷177. latch （汽机手动）打闸（停机），挂闸178. full speed 全速179. tightness/leakage test 严密性试验180. worm wheel 涡轮181. neutral earthing/ground neutral system 中性点接地系统182. grounding switch; earthing blade 接地刀闸183. auto quasi-synchronization 自动准同期184. AVR: automatic voltage regulator 自动电压调节器185. raising voltage from zero 零起升压（试验）186. no-load 空载187. negative phase sequence 负（相）序188. temperature rise test 温升试验189. water discharge pipe/pump 排水管/泵190. superheat degree 过热度191. AVT: all volatile treatment 全挥发性处理192. NWT: neutral water treatment 中性处理193. CWT: combined water treatment 综合处理194. sliding pressure 滑压195. self-sealing 自密封196. vacuum leakage test 真空严密性试验197. permissible/allowable error 允许误差198. deviation 误差，偏差199. tolerance 公差200. cleanrance间隙201. standard deviation STDV标准差202. hysterisis error 回程误差203. discontinuous running 间断运行204. hydraulic shock 水击205. auxiliary steam header/tank 辅汽联箱206. isolate/isolating valve 隔离阀207. be below standard; unqualified 不合格208. television camera of furnace flame 炉膛火焰电视摄像头209. flue gas duct 烟道210. air duct风道211. slagging, slag 结焦212. fouling 结垢213. clinker; slag 结渣214. clinker grinder 碎渣机215. feed gate 排渣门216. closed-circuit television(CCTV) 闭路电视217. 交流电AC 火线live，红色R；零线neutral ，蓝色B；接地线earthing，黄色Y或绿色直流电DC 正极positive + 红色线；负极negative - 黑色线218. Boiler Feedwater Pump Turbine(BFPT)219. screwdriver 螺丝刀，起子; slot type screwdriver一字/平口螺丝刀;Philips/cross screwdriver 十字螺丝刀220. screw 螺丝221. screw rod 螺杆222. bolts and nuts 螺栓螺帽223. pincers;vise, vice 老虎钳224. wrench 扳手225. anti-static 防静电226. megger 摇表，兆欧表227. meggering 绝缘测量228. redundancy 冗余229. banking fire 锅炉压火230. full arc admission 全周进汽231. welding seam 焊缝232. coagulant凝聚剂，混凝剂233. target load 目标负荷234. enthalpy 焓，音含；物理学上指单位质量的物质所含的全部热能。