ANSYS软件分析警告汇总

合集下载

ansys常见警告及错误

ansys常见警告及错误

ansys常见警告及错误A mesh could not be generated using the current meshing options and settings. Hint: The problem geometry areas might have been highlighted. Switching to wireframe mode may make them more visible. ⽆法使⽤当前⽹格⽣成⽹格选项和设置。

提⽰:⼏何区域可能是突出的问题。

切换到线框模式可能会让他们更明显。

Insufficient memory was available for the solver engine to obtain a solution. Try simplifying the model to reduce problem size. Please see the Troubleshooting section of the ANSYS Workbench Help System for more information.内存不⾜是解算器引擎可以获得⼀个解决⽅案。

试着简化模型来减少问题的⼤⼩。

请参见故障排除部分ANSYS Workbench帮助系统的更多信息。

The detected initial penetration/gap is relatively large for certain contact pairs. This may produce inaccurate results for Bonded and No Separation contacts using formulation other than MPC. This large penetration/gap can be identified by generating the initial contact results.检测到的初始渗透/差距相对较⼤的某些接触对。

ansys常见警告及错误

ansys常见警告及错误

ansys常见警告及错误A mesh could not be generated using the current meshing options and settings. Hint: The problem geometry areas might have been highlighted. Switching to wireframe mode maymake them more visible.无法使用当前网格生成网格选项和设置。

提示:几何区域可能是突出的问题。

切换到线框模式可能会让他们更明显。

Insufficient memory was available for the solver engine to obtain a solution. Try simplifying the model to reduce problem size. Please see the Troubleshooting section of the ANSYS Workbench Help System for more information.内存不足是解算器引擎可以获得一个解决方案。

试着简化模型来减少问题的大小。

请参见故障排除部分ANSYS Workbench帮助系统的更多信息。

The detected initial penetration/gap is relatively large for certain contact pairs. This may produce inaccurate results for Bonded and No Separation contacts using formulation other than MPC. This large penetration/gap can be identified by generating the initial contact results.检测到的初始渗透/差距相对较大的某些接触对。

ansys常见警告和错误

ansys常见警告和错误

ansys常见警告和错误ansys警告和错误2010-05-03 21:471、The value of UY at node 1195 is 449810067.It is greater than the current limit of 1000000.This generally indicates rigid body motion as a result of an unconstrained model. Verify that your model si properly constrained.错误的可能:1).出现了刚体位移,要增加约束2).求解之前先merge或者压缩一下节点3).有没有接触,如果接触定义不当,也会出现这样类似的情况4)材料属性设置不对会出现这种情况,例如密度设置的太离谱;我自己遇到这种情况的解决方案一般是检查没有耦合的结点;我遇到过这种情况最后发现是密度设置离谱了;2、Large negative pivot value...May be because of a bad temperature-dependent material property used in the model.出现这个错误很可能的原因是约束不够!请仔细检查模型!还没碰到过这个问题3、开始求解后出现以下提示,Solid model data is contaminated后来终于找到原因了有限元网格里包含一些未被划分网格的线,一般来说出现在面于面之间有重合的线,导致虽然面被划分了网格,却包含未被划分网格的线。

解决办法,把模型存为.cdb格式(去掉几何信息),然后再读取,就可以求解了命令:cdwrite,db,模型名,cdb听起来不错,不过也没遇到过,一般在划分后用一下NUMMRG 命令,合并元素,以避免这种情况出现4、*** WARNING ***There are 79 small equation solver pivot terms.几个可能:1) 约束不够,但警告有79 个方程出现小主元,这一条可能性较小,但也不妨检查一下。

ansys出错及警告信息汇总

ansys出错及警告信息汇总
原因:是因为我使用LATT的时候,把“--”的那个不小心填成了“1”。经过ANSYS的命令手册里说那是没有用的项目,但是根据我的理解,这些所谓的没有用的项目实际上都是ANSYS在为后续的版本留接口。对于LATT,实际上那个项目可能就是单元坐标系的设置。当我发现原因后,把1改成0——即使用全局直角坐标系,就没有WARNING了。当然,直接空白也没有问题。
NO.0011、
我在计算三维的时候出现一个error,如图所示,不知道代表什么意思啊?是说我的内存不足么?请问各位大侠,碰到这种问题应该怎么解决呢?当选择自由划分网格的时候,怎么样能使默认最小的网格更小呢?
error:Meshing of volume 5 has been aborted because of a lack of memory. Closed down other processes and/or choose a larger element size, then try the VMESH command again. Minimum additional memory required=853MB(by kitty_zoe )
NO.0004、 *TREAD end-of-file in data read
txt中的表格数据不完整!
NO.0005、 No *CREATE for *END. The *END command is ignored
忘了写*END了吧,呵呵
NO.0006、 Keypoint 1 is referenced by only one line. Improperly connected line set for AL command
这是ANSYS里面系统自己规定的操作要求的。(by wishangtian)

ansys_常见警告和错误(Ansys_commonerrorsandwarnings)

ansys_常见警告和错误(Ansys_commonerrorsandwarnings)

ansys_常见警告和错误(Ansys_ common errors and warnings)False possibility:1) a rigid body displacement occurs, adding constraints2) before solving merge or compression node3) there is no contact, and if the definition of contact is incorrect, a similar situation will occur4) this can happen if material properties are set incorrectly. For example, the density setting is too far off the mark;My own solution to this situation is to check the nodes without coupling; I've encountered this situation and finally found that the density is off the mark;2, Large, negative, pivot, value...May, be, because, of, a, bad, temperature-dependent, material, property, used,, in, the, model.The reason for this error is probably the lack of restraint!Please check the model carefully!I haven't met the problem yet3, after the beginning of the following tips,Solid, model, data, is, contaminatedFinally, I found out whyThe finite element mesh contains lines that are not divided into grids. In general, there is a coincidence between the faces, which leads to the fact that the mesh is divided into lines, but contains lines that have not been meshed.The solution is to store the model in.Cdb format (remove geometry information) and then read it to solve itCommand: cdwrite, DB, model name, CDBSounds good, but I haven't encountered it yet. After the partition, I use the NUMMRG command and merge elements to avoid this4, * * * WARNING * * *There are 79, small, equation, solver, pivot, terms.Several possibilities:1) the constraint is not enough, but the warning has 79 equations to appear small principal element, this one possibility is smaller, but may as well examine.2) the material parameter has the question, may examine the material data whether to lose the mistake.3) or some units did not make the material. You can use Select,Entities, -&gt, Element, -&gt, Attributes, -&gt, Material, Type, -&gt, and 0 (material number 0) to see if this is the case4) the structure is not one, that is, there are several independent entity groups, you can do modal analysis first to see if there is something alone vibration, or even fly out.I haven't had this problem, I hope5 、 appear frequently when importing the IGES fileBecause, keypoint, merging, has, been, performed, not, automatic, volume, creation, is, suppressedThis warning indicates that there is a coincidence point in the model. You can merge keypoint in ANSYSFor a slightly more complex model, IGES format is not recommended, either in PRT or.X-t formatIn addition, we recommend learning ANSYS WorkbenchIts interface is much better than ANSYS's.Did not encounter, it seems that practice or less, and more uphill to meet the tiger6, negative, radius, on, elementThe reason for the error of the negative radius:The axial symmetry problem in ANSYS is not the same as other software.Requirements must be Y Axis axis, and the model must be drawn on the positive half axis X, if your model to the negative half of XThere will be hints about the negative radius.Have encountered this problem,However, at that time did not figure out, and now understand, summed up the past, the perfect self7, input/output, error, on, unit=9., possible, full, diskProbably:1) the hard disk partition in the ANSYS working directory is full; (very likely)2) the system's virtual memory is full of hard disk partitions; (there is a certain possibility)3) the hard disk has bad sectors. (less likely)Sometimes is actually other errors (such as calculation and convergence), but false positives for disk space is not enough, therefore, need to observe the change process of disk space calculation, to determine whether the problem is indeed a disk space.Encountered this problem, but I do not know what the principle is solved, when the division is more, and then I reduce the unit to the previous 1/3, the results can be calculated. The remaining space of my disk has 100G, should not be first reasons, 2G memory, and the virtual memory is also adjusted, but still can not, so the second may also be smaller, as far as 3 is impossible8, when the grid is divided in ANSYS16, ANGLE, LESS, THAN, 2.5, DEGREES, FOUND, IN, TRIANGLE, FACETS, OF, VOLUME,, WITHSMALLEST, ANGLE, =1.2, POOR, ELEMENT, QUALITY, OR, MESH,, FAILURE, MAY, RESULT.What should I do to avoid this warning?. What is the problem if you ignore the solution?PS: when I use the automatic mesh model, there is the UG import, and the ANSYS version is 8The model directly imported must be repairedMerge the smaller line segmentsA few unimportant details are removedThen you can partition the meshDirect division must lead to the emergence of many distortion unitsNo, individuals tend to model directly9, Real, constant, set, -1, undefined, but, referenced,, by, elementThe element properties of the element quoted by unit 232 are out of order. The real constants of the units are usually checked. Does that define a problem?10, run after warning both solid loading model and finite element model boundary conditon have been apply to this model, as solid loads are transferred to the nodes or elements, they can overwrite directly applied loads this is to tell you, if you are on line or to face restrictions imposed by force or, rather than directly to the node the applied force or constraint. In the solution, it will force you to go to the node. Boolean, operation, Try, adjusting, the, tolerance, value, on, the, failed.BTOL, command, to, some, fraction, of, the, minimum, distance.Model, keypointSize (current, problem), 2.996529e+001, current, BTOL, setting1.000000e-005, minimum KPT distance 1.241535e-004. said the Boolean operation is the key point of the minimum distance between negligible exceeds the tolerance ANSYS by default, tolerance can be through the BTOL command to change the defaultby large Boolean operations,After that, the tolerance value is transferred back. The default tolerance value is 1E-5. Command format: BTOL, tolerance valueDiscontinuous, drag, line, pattern, for, ADRAG,, command, or, more, than, twoLines, attached, to, a, keypoint, in, the, drag, pattern., lineIn the process of dragging the line into line, if you want to drag more than one line at a time, you should note that the above error means that the object (line) is interrupted or that there is an intersection point with the path line. That is to say, if you want to drag more than one line at a time, you should ensure that these lines are continuous and do not intersect the path line.。

ansys常见错误汇总

ansys常见错误汇总
NO.0015
clear is not a recognized GEGIN command,abbreviation,or macro.
this command will be ingored.
那是因为打开了前处理,求解或者后处理,
先用FINISH命令,再用CLEAR就可以了
------------------------------------------------------------------------------------------------------------------
后来仔细检查,发现我TXT的数据文件里,分隔是采用TAB键分隔的。但是在最后一列后面,如果把鼠标点上去,发现数据后面还有一个空格键。于是,我把每个列最后多的空格键删除,然后发现上面的信息就没有了。
------------------------------------------------------------------------------------------------------------------
txt中的表格数据不完整!
------------------------------------------------------------------------------------------------------------------
NO.0005
No *CREATE for *END. The *END command is ignored
这个警告可以忽略。
------------------------------------------------------------------------------------------------------------------

ANSYS警告和报错信息汇总

ANSYS警告和报错信息汇总

ANSYS‎警告和报错‎信息汇总NO.0001、ESYS is not valid‎for line eleme‎n t.原因:是因为我使‎用LATT‎的时候,把“--”的那个不小‎心填成了“1”。

经过ANS‎Y S的命令‎手册里说那‎是没有用的‎项目,但是根据我‎的理解,这些所谓的‎没有用的项‎目实际上都‎是ANSY‎S在为后续‎的版本留接‎口。

对于LAT‎T,实际上那个‎项目可能就‎是单元坐标‎系的设置。

当我发现原‎因后,把1改成0‎——即使用全局‎直角坐标系‎,就没有WA‎R NING‎了。

当然,直接空白也‎没有问题。

NO.0002、使用*TREAD‎的时候,有的时候明‎明看文件好‎好的,可是却出现‎*TREAD‎end-of-file in data read.后来仔细检‎查,发现我TX‎T的数据文‎件里,分隔是采用‎T AB键分‎隔的。

但是在最后‎一列后面,如果把鼠标‎点上去,发现数据后‎面还有一个‎空格键。

于是,我把每个列‎最后多的空‎格键删除,,然后发现上‎面的信息就‎没有了。

NO.0003、Coeff‎i cien‎t ratio‎excee‎d s 1.0e8 - Check‎resul‎t s.这个大概是‎跟收敛有关‎,但是我找不‎到具体的原‎因。

我建立的一‎个桥梁分析‎模型,尽管我分析‎的结果完全‎符合我的力‎学概念判断‎,规律完全符‎合基本规律‎,数据也基本‎符合实际观‎测,但是却还是‎不断出现这‎个警告信息‎。

有人知道这‎个信息是什‎么意思,怎么调试能‎消除吗?NO.0004、*TREAD‎end-of-file in data readtxt中的‎表格数据不‎完整!NO.0005、No *CREAT‎E for *END. The *END comma‎n d is ignor‎e d忘了写*END了吧‎,呵呵NO.0006、 Keypo‎i nt 1 is refer‎e nced‎by only one line. Impro‎p erly‎conne‎c ted line set for AL comma‎n d 两条线不共‎点,尝试 nummr‎g命令NO.0007、 L1 is not a recog‎n ized‎PREP7‎comma‎n d, abbre‎v iati‎o n, or macro‎. This comma‎n d will be ignor‎e d还没有进入‎p rep7‎,先:/prep7‎NO.0008、Keypo‎i nt 2 belon‎g s to line 4 and canno‎t be moved‎同一位置点‎2已经存在‎了,尝试对同位‎置的生成新‎点换个编号‎,比如100‎2NO.0009、Shape‎testi‎n g revea‎l ed that 32 of the 640 new or modif‎i ed eleme‎n tsviola‎t e shape‎warni‎n g limit‎s. To revie‎w test resul‎t s, pleas‎e see theoutpu‎t file or issue‎the CHECK‎comma‎n d.单元形状奇‎异,在我的模型‎中6面体单‎元的三个边‎长差距较大‎,可忽略该错‎误NO.0010、用命令流建‎模的时候遇‎到的The drag direc‎t ion (from the keypo‎i nt on drag line 27 that is close‎s tto a keypo‎i nt KP of the given‎area 95) is ortho‎g onal‎to the areanorma‎l at that KP. Area canno‎t be dragg‎e d by the VDRAG‎comma‎n d.意思是拉伸‎源面的法向‎与拉伸路径‎垂直,不能使用V‎D RAG命‎令。

ansys常见错误汇总

ansys常见错误汇总

常见waring/erroe 汇总NO.0001ESYS is not valid for line element.原因:是因为我使用LATT的时候,把“--”的那个不小心填成了“1”。

经过ANSYS的命令手册里说那是没有用的项目,但是根据我的理解,这些所谓的没有用的项目实际上都是ANSYS在为后续的版本留接口。

对于LATT,实际上那个项目可能就是单元坐标系的设置。

当我发现原因后,把1改成0——即使用全局直角坐标系,就没有WARNING了。

当然,直接空白也没有问题。

------------------------------------------------------------------------------------------------------------------ NO.0002使用*TREAD的时候,有的时候明明看文件好好的,可是却出现*TREAD end-of-file in data read. 后来仔细检查,发现我TXT的数据文件里,分隔是采用TAB键分隔的。

但是在最后一列后面,如果把鼠标点上去,发现数据后面还有一个空格键。

于是,我把每个列最后多的空格键删除,然后发现上面的信息就没有了。

------------------------------------------------------------------------------------------------------------------ NO.0003Coefficient ratio exceeds 1.0e8 - Check results.这个大概是跟收敛有关,但是我找不到具体的原因。

我建立的一个桥梁分析模型,尽管我分析的结果完全符合我的力学概念判断,规律完全符合基本规律,数据也基本符合实际观测,但是却还是不断出现这个警告信息。

------------------------------------------------------------------------------------------------------------------ NO.0004*TREAD end-of-file in data readtxt中的表格数据不完整!------------------------------------------------------------------------------------------------------------------ NO.0005No *CREATE for *END. The *END command is ignored忘了写*END了吧,呵呵------------------------------------------------------------------------------------------------------------------ NO.0006Keypoint 1 is referenced by only one line. Improperly connected line set for AL command 两条线不共点,尝试nummrg命令。

ANSYS软件分析警告汇总

ANSYS软件分析警告汇总

ANSYS软件错误集锦1 在Ansys中出现“Shape testing revealed that 450 of the 1500 new or modified elements violate shape warning limits.”,是什么原因造成的呢?单元网格质量不够好,尽量用规则化网格,或者再较为细密一点。

2 在Ansys中,用Area Fillet对两空间曲面进行倒角时出现以下错误:Area 6 offset could not fully converge to offset distance 10. Maximum error between the two surfaces is 1% of offset distance.请问这是什么错误?怎么解决?其中一个是圆柱接管表面,一个是碟形封头表面。

ansys的布尔操作能力比较弱。

如果一定要在ansys里面做的话,那么你试试看先对线进行倒角,然后由倒角后的线形成倒角的面。

建议最好用UG、PRO/E这类软件生成实体模型然后导入到ansys。

3 在Ansys中,出现错误“There are 21 small equati on solver pivot terms。

”,是否是在建立接触contact时出现的错误?不是建立接触对的错误,一般是单元形状质量太差(例如有接近零度的锐角或者接近180度的钝角)造成small equation solver pivot terms4 在Ansys中,出现警告“SOLID45 wedges are recommended only in regions of relatively low stress gradients.”,是什么意思?"这只是一个警告,它告诉你:推荐SOLID45单元只用在应力梯度较低的区域。

它只是告诉你注意这个问题,如果应力梯度较高,则可能计算结果不可信。

"5 ansys向adams导的过程中,出现如下问题“There is not enough memory for the Sparse Matrix Solver to proceed.Please shut down other applications that may be running or increase the virtual memory on your system and return ANSYS.Memory currently allocated for the Sparse Matrix Solver=50MB.Memory currently required for the Sparse Matrix Solver to continue=25MB”,是什么原因造成的?不清楚你ansys导入adams过程中怎么还需要使用Sparse Matrix Solver(稀疏矩阵求解器)。

ANSYS常见错误和警告及其解决方法

ANSYS常见错误和警告及其解决方法

ANSYS常见错误和警告及其解决方法1、some contact elements overlap with the other contact element which can cause over constraint。

一些接触单元与其他接触单元重叠,这可能导致过度约束。

解决方法:这是由于在同一实体上,即有绑定接触(MPC)的定义,又有刚性区或远端载荷(MPC)的定义,操作中在定义刚性区或远端载荷时避免选择不必要的DOF自由度,以消除过约束。

2、error:element type 1 is PLANE42,which can't be used with the VMES command,meshing of volume 3 aborted。

单元类型1是PLANE42,不能使用命令VMES划分体网格,划分体3中止。

解决方法:修改单元类型为适合体网格的单元类型,如solid、shell等;使用AMESH。

3、error:keypoint 10 is referenced by only one line. Improperly connected line set for AL command。

关键点10只在一条线上。

不适合使用AL命令连接线。

解决方法:AL命令是用线来定义面,而选择两条线可能只有两个关键点,因为关键点10不在线上,而定义面至少有三个点,因此,需要再选一条线。

4、Element type 1 is Solid95,which can not be used with the AMES command,meshing of area 2 aborted。

这是因为不同单元类型对应不同的划分网格操作。

上面的错误是因为单元类型为Solid95(实体单元),不能用AMES命令划分面网格。

5、Shear modulus must be positive for material 1 in element 1。

ansys警告信息解决方法

ansys警告信息解决方法

ansys警告信息解决方法NO.0001、ESYS is not valid for line element.原因:是因为我使用LATT的时候,把“--”的那个不小心填成了“1”。

经过ANSYS的命令手册里说那是没有用的项目,但是根据我的理解,这些所谓的没有用的项目实际上都是ANSYS在为后续的版本留接口。

对于LATT,实际上那个项目可能就是单元坐标系的设置。

当我发现原因后,把1改成0——即使用全局直角坐标系,就没有WARNING了。

当然,直接空白也没有问题。

NO.0002、使用*TREAD的时候,有的时候明明看文件好好的,可是却出现*TREAD end-of-file in data read.后来仔细检查,发现我TXT的数据文件里,分隔是采用TAB键分隔的。

但是在最后一列后面,如果把鼠标点上去,发现数据后面还有一个空格键。

于是,我把每个列最后多的空格键删除,,然后发现上面的信息就没有了。

NO.0003、 Coefficient ratio exceeds 1.0e8 - Check results.这个大概是跟收敛有关,但是我找不到具体的原因。

我建立的一个桥梁分析模型,尽管我分析的结果完全符合我的力学概念判断,规律完全符合基本规律,数据也基本符合实际观测,但是却还是不断出现这个警告信息。

有人知道这个信息是什么意思,怎么调试能消除吗?NO.0004、*TREAD end-of-file in data readtxt中的表格数据不完整!NO.0005、No *CREATE for *END. The *END command is ignored忘了写*END了吧,呵呵NO.0006、Keypoint 1 is referenced by only one line. Improperly connected line set for AL command两条线不共点,尝试 nummrg命令NO.0007、L1 is not a recognized PREP7 command,abbreviation, or macro.This command will be ignored 还没有进入prep7,先:/prep7NO.0008、Keypoint 2 belongs to line 4 and cannot be moved 同一位置点2已经存在了,尝试对同位置的生成新点换个编号,比如1002NO.0009、Shape testing revealed that 32 of the 640 new or modified elements violate shape warning limits.To review test results, please see the output file or issue the CHECK command.单元形状奇异,在我的模型中6面体单元的三个边长差距较大,可忽略该错误NO.0010、用命令流建模的时候遇到的The drag direction (from the keypoint on drag line 27 that is closest to a keypoint KP of the given area 95) is orthogonal to the area normal at that KP.Area cannot be dragged by the VDRAG command.意思是拉伸源面的法向与拉伸路径垂直,不能使用VDRAG命令。

ansys警告和报错信息汇总 (1)

ansys警告和报错信息汇总 (1)

javascript:showReg(0);ANSYS警告和报错信息汇总NO.0001、ESYS is not valid for line element.原因:是因为我使用LATT的时候,把“--”的那个不小心填成了“1”。

经过ANSYS的命令手册里说那是没有用的项目,但是根据我的理解,这些所谓的没有用的项目实际上都是ANSYS在为后续的版本留接口。

对于LATT,实际上那个项目可能就是单元坐标系的设置。

当我发现原因后,把1改成0——即使用全局直角坐标系,就没有WARNING了。

当然,直接空白也没有问题。

NO.0002、使用*TREAD的时候,有的时候明明看文件好好的,可是却出现*TREAD end-of-file in data read.后来仔细检查,发现我TXT的数据文件里,分隔是采用TAB键分隔的。

但是在最后一列后面,如果把鼠标点上去,发现数据后面还有一个空格键。

于是,我把每个列最后多的空格键删除,,然后发现上面的信息就没有了。

NO.0003、Coefficient ratio exceeds 1.0e8 - Check results.这个大概是跟收敛有关,但是我找不到具体的原因。

我建立的一个桥梁分析模型,尽管我分析的结果完全符合我的力学概念判断,规律完全符合基本规律,数据也基本符合实际观测,但是却还是不断出现这个警告信息。

有人知道这个信息是什么意思,怎么调试能消除吗?NO.0004、*TREAD end-of-file in data readtxt中的表格数据不完整!NO.0005、No *CREATE for *END. The *END command is ignored忘了写*END了吧,呵呵NO.0006、Keypoint 1 is referenced by only one line. Improperly connected line set for AL command两条线不共点,尝试nummrg命令NO.0007、L1 is not a recognized PREP7 command, abbreviation, or macro. This command will be ignored还没有进入prep7,先:/prep7NO.0008、Keypoint 2 belongs to line 4 and cannot be moved同一位置点2已经存在了,尝试对同位置的生成新点换个编号,比如1002NO.0009、Shape testing revealed that 32 of the 640 new or modified elementsviolate shape warning limits. To review test results, please see theoutput file or issue the CHECK command.单元形状奇异,在我的模型中6面体单元的三个边长差距较大,可忽略该错误NO.0010、用命令流建模的时候遇到的The drag direction (from the keypoint on drag line 27 that is closestto a keypoint KP of the given area 95) is orthogonal to the areanormal at that KP. Area cannot be dragged by the VDRAG command.意思是拉伸源面的法向与拉伸路径垂直,不能使用VDRAG命令。

ANSYS警告和报错信息汇总

ANSYS警告和报错信息汇总

ANSYS警告和报错信息汇总NO.0001、ESYS is not valid for line element.原因:是因为我使⽤LATT的时候,把“--”的那个不⼩⼼填成了“1”。

经过ANSYS的命令⼿册⾥说那是没有⽤的项⽬,但是根据我的理解,这些所谓的没有⽤的项⽬实际上都是ANSYS在为后续的版本留接⼝。

对于LATT,实际上那个项⽬可能就是单元坐标系的设置。

当我发现原因后,把1改成0——即使⽤全局直⾓坐标系,就没有WARNING了。

当然,直接空⽩也没有问题。

NO.0002、使⽤*TREAD的时候,有的时候明明看⽂件好好的,可是却出现 *TREAD end-of-file in data read.后来仔细检查,发现我TXT的数据⽂件⾥,分隔是采⽤TAB键分隔的。

但是在最后⼀列后⾯,如果把⿏标点上去,发现数据后⾯还有⼀个空格键。

于是,我把每个列最后多的空格键删除,,然后发现上⾯的信息就没有了。

NO.0003、 Coefficient ratio exceeds 1.0e8 - Check results.这个⼤概是跟收敛有关,但是我找不到具体的原因。

我建⽴的⼀个桥梁分析模型,尽管我分析的结果完全符合我的⼒学概念判断,规律完全符合基本规律,数据也基本符合实际观测,但是却还是不断出现这个警告信息。

有⼈知道这个信息是什么意思,怎么调试能消除吗?NO.0004、*TREAD end-of-file in data readtxt中的表格数据不完整!NO.0005、No *CREATE for *END. The *END command is ignored忘了写*END了吧,呵呵NO.0006、 Keypoint 1 is referenced by only one line. Improperly connected line set for AL command两条线不共点,尝试 nummrg命令NO.0007、 L1 is not a recognized PREP7 command, abbreviation, or macro. This command will be ignored还没有进⼊prep7,先:/prep7NO.0008、Keypoint 2 belongs to line 4 and cannot be moved同⼀位置点2已经存在了,尝试对同位置的⽣成新点换个编号,⽐如1002NO.0009、Shape testing revealed that 32 of the 640 new or modified elementsviolate shape warning limits. To review test results, please see theoutput file or issue the CHECK command.单元形状奇异,在我的模型中6⾯体单元的三个边长差距较⼤,可忽略该错误NO.0010、⽤命令流建模的时候遇到的The drag direction (from the keypoint on drag line 27 that is closestto a keypoint KP of the given area 95) is orthogonal to the areanormal at that KP. Area cannot be dragged by the VDRAG command.意思是拉伸源⾯的法向与拉伸路径垂直,不能使⽤VDRAG命令。

ANSYS常见错误提示和解决办法

ANSYS常见错误提示和解决办法

NO.0001ESYS is not valid for line element.原因:是因为我使用LATT的时候,把“--”的那个不小心填成了“1”。

经过ANSYS的命令手册里说那是没有用的项目,但是根据我的理解,这些所谓的没有用的项目实际上都是ANSYS在为后续的版本留接口。

对于LATT,实际上那个项目可能就是单元坐标系的设置。

当我发现原因后,把1改成0——即使用全局直角坐标系,就没有WARNING了。

当然,直接空白也没有问题。

NO.0002使用*TREAD的时候,有的时候明明看文件好好的,可是却出现 *TREAD end-of-file in data read.后来仔细检查,发现我TXT的数据文件里,分隔是采用TAB键分隔的。

但是在最后一列后面,如果把鼠标点上去,发现数据后面还有一个空格键。

于是,我把每个列最后多的空格键删除,然后发现上面的信息就没有了。

NO.0003Coefficient ratio exceeds 1.0e8 - Check results.这个大概是跟收敛有关,但是我找不到具体的原因。

我建立的一个桥梁分析模型,尽管我分析的结果完全符合我的力学概念判断,规律完全符合基本规律,数据也基本符合实际观测,但是却还是不断出现这个警告信息。

NO.0004*TREAD end-of-file in data readtxt中的表格数据不完整!NO.0005No *CREATE for *END. The *END command is ignored忘了写*END了吧,呵呵NO.0006Keypoint 1 is referenced by only one line. Improperly connected line set for AL command两条线不共点,尝试 nummrg命令。

NO.0007L1 is not a recognized PREP7 command, abbreviation, or macro. This command will be ignored还没有进入prep7,先:/prep7NO.0008Keypoint 2 belongs to line 4 and cannot be moved关键点2属于线4,移动低级体素时先移动高级体素!NO.0009Shape testing revealed that 32 of the 640 new or modified elementsviolate shape warning limits. To review test results, please see theoutput file or issue the CHECK command.单元形状奇异,在我的模型中6面体单元的三个边长差距较大,可忽略该错误NO.0010用命令流建模的时候遇到的The drag direction (from the keypoint on drag line 27 that is closestto a keypoint KP of the given area 95) is orthogonal to the areanormal at that KP. Area cannot be dragged by the VDRAG command. 意思是拉伸源面的法向与拉伸路径垂直,不能使用VDRAG命令出现的环境ASEL,S,LOC,Z,143e-3VDRAG,ALL, , , , , , 27本意是按位置z=143e-3位置的面,然后沿编号27的线拉伸,出错,之前用该语句没有任何问题。

ansys错误汇总大全,史上最全

ansys错误汇总大全,史上最全

ANSYS分析出现问题NSYS error message 错误信息汇总2011-10-19 12:57:12| 分类:ANSYS | 标签:ansys 错误error |举报|字号订阅以前很多的心得全丢了,现在把新遇到的error message及解决方法逐一添加如下:1\ Too many expressions.表达式太长,ansys要求一个表达式不要超过6个分段,比如以下不对A22=y1*z2-y1*z3-y2*z1+y2*z3+y3*z1-y3*z2 有7个段改为A22=y1*z2-y1*z3-y2*z1+y2*z3+y3*z1A22=A22-y3*z2就行了2\ No *DO trips needed, enter *ENDDO .循环执行次数为0,说明下标的变化范围越界,就是形如下面的循环*do,i,0,-1..........*enddo3\ *** NOTE *** CP = 227.688 TIME= 12:30:54One or more elements have become highly distorted. Excessivedistortion of elements is usually a symptom indicating the need forcorrective action elsewhere. Try incrementing the load more slowly(increase the number of substeps or decrease the time step size). Youmay need to improve your mesh to obtain elements with better aspectratios. Also consider the behavior of materials, contact pairs,and/or constraint equations. If this message appears in the firstiteration of first substep, be sure to perform element shape checking.为什么上面的错误信息用深色底纹标出呢?原因很简单,上面的错误出现在非线性计算中意味着致命错误,说明计算无法收敛,遇到这个错误是非常头疼的,下面重点讨论这个问题的由来和解决办法。

ansys警告语总结

ansys警告语总结

4、在做一个轴对称分析,计算中出现错误"negative radius element ** (*为单元号)
[1]是边界约束的问题,因为是实心园球,所以在对称轴上的单元要施加约束,横向不能有位移,因为以y轴做对称轴,所以反应出来就是出现了负的x坐标,应该加x方向的约束。加了约束就好了
5、There are 1 small equation solver pivot terms.
1、There are 5 small equation solver pivot terms.
[1]出現的可能原因
你的負載是否跟時間有關(如果有設隨時間變化的負載,那需更改成瞬态分析)
單元比例差異過大造成過度畸变(試者加密關鍵區域網格)
約束不足或者是做靜態非線性問題時也會出現(考量變形模式或嘗試變更合理的拘束點)
[1]通常可以忽略,因为144892 很有可能是一个不需要定义材料的辅助单元。
3、Element shape checking is currently inactive. Issue SHPP,ON or SHPP,WARN to reactivate, if desired.
[1]该警告说明网格有问题,网格质量不好
[1]表示刚度矩阵中出现了小主元(主对角线上的元素接近为0),有可能是局部变形过大或者是约束不够
2、*** WARNING *** CP = 2.359 TIME= 17:35:06
Material number 7 (used by element 4352 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available.

ansys_常见警告和错误

ansys_常见警告和错误

ansys警告和错误2010-05-03 21:471、The value of UY at node 1195 is 449810067.It is greater than the current limit of 1000000.This generally indicates rigid body motion as a result of an unconstrained model. Verify that your model si properly constrained.错误的可能:1).出现了刚体位移,要增加约束2).求解之前先merge或者压缩一下节点3).有没有接触,如果接触定义不当,也会出现这样类似的情况4)材料属性设置不对会出现这种情况,例如密度设置的太离谱;我自己遇到这种情况的解决方案一般是检查没有耦合的结点;我遇到过这种情况最后发现是密度设置离谱了;2、Large negative pivot value...May be because of a bad temperature-dependent material property used in the model. 出现这个错误很可能的原因是约束不够!请仔细检查模型!还没碰到过这个问题3、开始求解后出现以下提示,Solid model data is contaminated后来终于找到原因了有限元网格里包含一些未被划分网格的线,一般来说出现在面于面之间有重合的线,导致虽然面被划分了网格,却包含未被划分网格的线。

解决办法,把模型存为.cdb格式(去掉几何信息),然后再读取,就可以求解了命令:cdwrite,db,模型名,cdb听起来不错,不过也没遇到过,一般在划分后用一下NUMMRG命令,合并元素,以避免这种情况出现4、*** WARNING ***There are 79 small equation solver pivot terms.几个可能:1) 约束不够,但警告有 79 个方程出现小主元,这一条可能性较小,但也不妨检查一下。

ansys警告错误信息汇总 (1)

ansys警告错误信息汇总 (1)

警告错误信息汇总NO.0001、ESYS is not valid for line element.原因:是因为我使用LATT的时候,把“--”的那个不小心填成了“1”。

经过ANSYS的命令手册里说那是没有用的项目,但是根据我的理解,这些所谓的没有用的项目实际上都是ANSYS在为后续的版本留接口。

对于LATT,实际上那个项目可能就是单元坐标系的设置。

当我发现原因后,把1改成0——即使用全局直角坐标系,就没有WARNING了。

当然,直接空白也没有问题。

NO.0002、使用*TREAD的时候,有的时候明明看文件好好的,可是却出现*TREAD end-of-file in dataread.后来仔细检查,发现我TXT的数据文件里,分隔是采用TAB键分隔的。

但是在最后一列后面,如果把鼠标点上去,发现数据后面还有一个空格键。

于是,我把每个列最后多的空格键删除,,然后发现上面的信息就没有了。

NO.0003、Coefficient ratio exceeds 1.0e8 - Check results.这个大概是跟收敛有关,但是我找不到具体的原因。

我建立的一个桥梁分析模型,尽管我分析的结果完全符合我的力学概念判断,规律完全符合基本规律,数据也基本符合实际观测,但是却还是不断出现这个警告信息。

有人知道这个信息是什么意思,怎么调试能消除吗?NO.0004、*TREAD end-of-file in data readtxt中的表格数据不完整!NO.0005、No *CREATE for *END. The *END command is ignored忘了写*END了吧,呵呵NO.0006、Keypoint 1 is referenced by only one line. Improperly connected lineset for ALcommand两条线不共点,尝试nummrg命令NO.0007、L1 is not a recognized PREP7 command, abbreviation, or macro.This command willbe ignored还没有进入prep7,先:/prep7NO.0008、Keypoint 2 belongs to line 4 and cannot be moved同一位置点2已经存在了,尝试对同位置的生成新点换个编号,比如1002NO.0009、Shape testing revealed that 32 of the 640 new or modified elementsviolate shape warning limits. To review test results, please see theoutput file or issue the CHECK command.单元形状奇异,在我的模型中6面体单元的三个边长差距较大,可忽略该错误NO.0010、用命令流建模的时候遇到的The drag direction (from the keypoint on drag line 27 that is closestto a keypoint KP of the given area 95) is orthogonal to the areanormal at that KP. Area cannot be dragged by the VDRAG command.意思是拉伸源面的法向与拉伸路径垂直,不能使用VDRAG命令。

ansys需要注意的警告

ansys需要注意的警告

NO.0001、ESYS is not valid for line element。

原因:是因为我使用LATT的时候,把“—-”的那个不小心填成了“1”。

经过ANSYS的命令手册里说那是没有用的项目,但是根据我的理解,这些所谓的没有用的项目实际上都是ANSYS在为后续的版本留接口.对于LATT,实际上那个项目可能就是单元坐标系的设置。

当我发现原因后,把1改成0-—即使用全局直角坐标系,就没有WARNING了。

当然,直接空白也没有问题.NO。

0002、使用*TREAD的时候,有的时候明明看文件好好的,可是却出现*TREAD end—of-file in data read。

后来仔细检查,发现我TXT的数据文件里,分隔是采用TAB键分隔的。

但是在最后一列后面,如果把鼠标点上去,发现数据后面还有一个空格键.于是,我把每个列最后多的空格键删除,,然后发现上面的信息就没有了。

NO.0003、 Coefficient ratio exceeds 1.0e8 - Check results.这个大概是跟收敛有关,但是我找不到具体的原因。

我建立的一个桥梁分析模型,尽管我分析的结果完全符合我的力学概念判断,规律完全符合基本规律,数据也基本符合实际观测,但是却还是不断出现这个警告信息。

有人知道这个信息是什么意思,怎么调试能消除吗?NO.0004、*TREAD end—of—file in data readtxt中的表格数据不完整!NO。

0005、No *CREATE for *END. The *END command is ignored忘了写*END了吧,呵呵NO。

0006、 Keypoint 1 is referenced by only one line. Improperly connected line set for AL command两条线不共点,尝试 nummrg命令NO.0007、L1 is not a recognized PREP7 command, abbreviation,or macro.This command will be ignored还没有进入prep7,先:/prep7NO。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

ANSYS软件错误集锦1 在Ansys中出现“Shape testing revealed that 450 of the 1500 new or modified elements violate shape warning limits.”,是什么原因造成的呢?单元网格质量不够好,尽量用规则化网格,或者再较为细密一点。

2 在Ansys中,用Area Fillet对两空间曲面进行倒角时出现以下错误:Area 6 offset could not fully converge to offset distance 10. Maximum error between the two surfaces is 1% of offset distance.请问这是什么错误?怎么解决?其中一个是圆柱接管表面,一个是碟形封头表面。

ansys的布尔操作能力比较弱。

如果一定要在ansys里面做的话,那么你试试看先对线进行倒角,然后由倒角后的线形成倒角的面。

建议最好用UG、PRO/E这类软件生成实体模型然后导入到ansys。

3 在Ansys中,出现错误“There are 21 small equati on solver pivot terms。

”,是否是在建立接触contact时出现的错误?不是建立接触对的错误,一般是单元形状质量太差(例如有接近零度的锐角或者接近180度的钝角)造成small equation solver pivot terms4 在Ansys中,出现警告“SOLID45 wedges are recommended only in regions of relatively low stress gradients.”,是什么意思?"这只是一个警告,它告诉你:推荐SOLID45单元只用在应力梯度较低的区域。

它只是告诉你注意这个问题,如果应力梯度较高,则可能计算结果不可信。

"5 ansys向adams导的过程中,出现如下问题“There is not enough memory for the Sparse Matrix Solver to proceed.Please shut down other applications that may be running or increase the virtual memory on your system and return ANSYS.Memory currently allocated for the Sparse Matrix Solver=50MB.Memory currently required for the Sparse Matrix Solver to continue=25MB”,是什么原因造成的?不清楚你ansys导入adams过程中怎么还需要使用Sparse Matrix Solver(稀疏矩阵求解器)。

估计是scrach memery太低了,从ansys product launcher 进入设置内存,total workspace和dataspace的差就是scrach memery。

如:total workspace 1150MB,dataspace200MB,scrach memery 就是1150-200=950MB。

6 在Ansys中,出现错误“error:element type 1 is PLANE42,which can't be used with the VMES command, meshing of volume 3 aborted.”,是什么意思?意思是:单元类型1是PLANE42,不能使用划分体网格的命令VMES,划分体3中止。

改进办法:1修改单元类型为适合体网格的单元类型。

如solid,或shell。

2不使用VMES 命令,使用AMESH。

7 在Ansys中,出现错误“error: key point 10 is referenced by only one line. Improperly connected line set for AL command.”,是什么意思?该怎么解决?意思是:关键点10只在一条线上。

不适合使用AL命令连接线。

AL命令是用线来定义面,而选择两条线可能只有两个关键点,因为关键点10不在线上,而定义面至少有三个点。

改进办法:再选一条线8 在Ansys中,出现警告“waring :constraint equation 212 does not have a unique slave dof.”是什么原因?怎么解决?原因:边界约束条件和约束方程在同一节点位置交叠解决方法:或者只加约束条件,或者只加约束方程9 在Ansys进行单元转配时,出现问题“node 8471 does not lie on or near the selected elements.The CEINTF operation produced no results for this node.”,该怎么解决?正确装配步骤是什么?单元装配时,中间操作/命令流步骤,添加了冗余的操作/命令。

正确步骤为:1)XSEL/ESLX/CM,X-ELEM,ELEM;2)XSEL/NSLX/CM,X-NODE,NODE;3)CEINTF 顺序不乱,也不能有冗余命令。

任何诸如CM,X-X,X,比如CM,A-No,AREA出现在步骤中,都会导致错误。

10 在Ansys中,出现警告“Term 4 (node 5000 rotz)on CE number 3331 is not active on any element。

This term is ignored。

”,是什么原因?怎么解决?这一warning发生当主节点坐标系与从节点坐标系不在同一个坐标体系下时。

例如主节点坐标系为总体直角坐标系,而从节点坐标系为总体圆柱体坐标系。

解决方法,就是保证二者坐标体系相一致。

11 Ansys模型中有圆柱和长方体相切,相切的附近单元划分时,出现不好的警告,该怎么解决?有什么好的划分单元格方法吗?解决方法一:寻求划分比较好的网格质量(最佳方法)。

可以通过改变建模策略和网格划分策略实现解决方法二:采用更多的载荷步,以及更多的载荷子步。

12 在一个Ansys实体模型上加弯矩后出现的警告“Term 1 (node 3525 ROTX) on CE number 4 is not active on any element。

This CE is ignored.”,可能是什么原因?原因:Term 1 (node 3525 ROTX) on CE number 4 is not active on any element 就是说,节点3525的ROTX自由度不在任何单元中active,没有哪个单元支持ROTX自由度。

13 在Ansys中,定义选取一定范围节点时,遇到错误“For item= LOC, the component ( 90-() is invalid. The NSEL command is ignored.”,可能是什么原因?怎么解决?原因是在编写命令流时候,括号是用中文输入法输入,导致命令无法识别。

将相应命令用英文输入即可。

14 在Ansys中,对一个复杂型面的叶片划分单元,采用自由划分网格,出现如下警告和错误,应该怎么解决?这个应该是因为你面积13的形状比较特殊,网格在这个面积划分时候,质量特别不好导致。

试着将面积13再细化后,划分网格。

15 在Ansys划分网格时,出现错误“Error! Element type 1 is Solid95,which can not be used with the AMES command, meshing of area 2 aborted.”,是什么原因引起的?怎么解决?刚开始学习的人经常出这种错误,这是因为不同单元类型对应不同的划分网格操作。

上面的错误是说单元类型为Solid95(实体类型),不能用AMES命令划分面网格。

16 在Ansys仿真时,出现错误“Meshing of volume 5 has been aborted because of a lack of memory. Closed down otherprocesses and/or choose a larger element size, then try the VMESH command again. Minimum additional memory required=853MB.”,可能是什么原因引起?怎么解决?说你的内存空间不够,可能因为你的计算单元太多,增加mesh尺寸,减少数量或者增加最小内存设定(ansys10中在customization preferences菜单存储栏可以修改)17 在Ansys仿真时,遇到错误“Body load from line 61 is not transferred to uns elected node 3122.”,是不是用SOLID65 单元比较好?SOLID65是空间混凝土实体单元,用于模拟混凝土的受力。

该单元可用于建立素混凝土模型,也可加筋建立钢筋混凝土模型。

该单元有8个节点,每个节点又X、Y、Z 3个平动自由度。

18 在Ansys中,当定义了数组*dim, a,,20,1时,赋初值a(1)=1,2,3,.....20,发现有些a 中的数值与所赋予的不符,为什么会这样?采用这种赋值方式时,赋初值不能超过10个。

a(1)=1,2,...,10a(11)=11,12, (20)这样赋初值就能解决上面的问题了。

19 在Ansys中碰到警告“*** WARNING *** There are 1 small equation solver pivot terms.”,这是什么警告?该怎么解决?ansys,刚度矩阵主元太小,可能是单元畸形,或者材料参数有问题,总之这个问题你就不断的换个方式建立模型,trial and error ,往往就解决了这个问题20 在Ansys中碰到错误“Shear modulus must be positive for material 1 in element 1.”,这个错误是什么意思?材料参数有问题。

使剪切模量为负。

21 "在Ansys中碰到警告“*** WARNING *** CP = 8.922 TIME= 10:37:30 Specified DOF constraint UY at unused node 350010. ”和警告“*** WARNING *** SUPPRESSED MESSAGE CP = 8.984 TIME= 10:37:30Force load on unused node 101403 FY.”,这是什么警告?"加边界的节点未包含在计算模型中。

相关文档
最新文档