EIOHF以太网远程IO联网产品快速安装指南
EIO用户使用手册v1.6
EDPF-NT Plus EIO使用手册版本 2.0编号 UG000北京国电智深控制技术有限公司2010年12月版权声明本手册版权归北京国电智深控制技术有限公司所有。
修订历史版本日期说明REV 1.0 2009-1 第1版REV 1.62010-12-22新添网络冗余，虚拟DPU在与EIO网络通讯中断后实现主、备切换，通讯的容错次数为可配置EIO用户使用手册目录1. 简介 (4)2. 设备、任务、虚拟卡件 (4)2.1 定义 (4)2.2 设备与任务的划分规则 (5)2.3 任务与虚拟卡件的对应关系 (5)3. EIO通讯配置步骤 (6)3.1 配置网络环境 (6)3.2 创建虚拟DPU (6)3.3 安装虚拟DPU (7)3.4 组态 (7)3.4.1 创建卡件布置图 (7)3.4.2 配置虚拟卡件 (7)3.5 创建“配置文件” (8)3.5.1 文件目录 (8)3.5.2 配置规则 (8)4. 错误排查与确认 (11)5. 实际工程应用举例 (12)1. 简介EIO即扩展I/O，其支持DCS与第三方系统通讯。
本文档重点介绍DCS通过虚拟DPU与第三方系统通讯的实现方案，虚拟DPU运行在NT+系统的MMI站上，一个虚拟DPU可同时和多个第三方系统通讯。
DCS与第三方系统之间可基于以太网或串口通讯，通讯协议为Modbus over TCP/IP 或Modbus RTU。
在实际应用中，将根据不同需求采用不同的通讯方案：①基于以太网通讯：通讯协议为Modbus over TCP/IP，DCS与每个第三方系统均可视为网络上的一个通讯结点，需要知道每个结点的IP地址和端口号，配置文件中将明确指定每个通讯结点的IP和端口号。
②基于串口通讯：通讯协议为Modbus RTU，DCS与第三方系统之间通过串口服务器作为转接接口。
串口服务器一端通过以太网和DCS连接，另一端则通过RS485和第三方系统连接。
串口服务器通常具有多个连接端口，每个端口连接一个第三方系统。
R5-NE1远程I O通信模块规格书说明书
远程 I/O R5 系列通信模块机型: R5－NE1① ①在下列代码中选择。
（例如: R5－NE1/Q）・特殊规格 (例如: /C01)①附加代码◆特殊规格未填写：无特殊规格/Q：特殊规格（请从特殊规格之项另行选择）/C01: 硅涂层/C02: 聚氨酯涂层/C03: 橡胶涂层 IP地址可用组态软件进行设定。
可在本公司的网站上下载组态软件。
将本产品连接到电脑时，需要专用的连接电缆线。
所需专 用电缆线的型号请参照本公司网站的下载网站或组态软件 的使用说明书。
注）此软件的运作状况是在日文版与英文版OS上确认的。
・Ethernet: RJ-45接口・内部通信总线: 连接到底座 (机型: R5－BS) 上・内部电源: 由底座 (机型: R5－BS) 提供隔离: Ethernet－内部通信总线・内部电源间RUN显示灯: 红/绿2色LED通信正常时亮绿色灯；接收数据时亮红色灯(用DIP开关进行切换)ERR显示灯: 红/绿2色LED通信异常时绿色灯亮灯/闪烁；发送数据时，亮红色灯(用DIP开关进行切换)数据占有区设定: 用侧面的DIP开关设定占有区1或占有区2传输类型: 10BASE-T/100BASE-TX传输速度: 10/100Mbps (备有Auto Negotiation功能)通信协议: Modbus/TCP数据: RTU (二进制)通信链接数: 2个通信电缆线:・10BASE-T (STP电缆线Category 5)・100BASE-TX (STP电缆线Category 5e)最长节段: 100mIP地址: 可用组态软件 (机型: R5CON) 进行变更(初始值: 192.168.0.1)端口编号: 502Ethernet显示灯: LINK、DPLX、LINK10、LINK100、COL使用湿度范围: 30～90%RH (无冷凝)使用大气条件: 无腐蚀性气体和严重尘埃安装: 安装在底座 (机型: R5－BS) 上重量: 约100g隔离强度: Ethernet－内部通信总线・内部电源间1500V AC 1分钟电磁兼容指令（EMC指令） EMI EN 61000-6-4 EMS EN 61000-6-2RoHS指令注) 作为符合EU指令的产品使用时，要与Ver.2.00以上的电源模块 (机型: R5－PS) 一起使用。
NPort IA5000A-I O 和 IAW5000A-I O 系列快速安装指南说明书
P/N: 1802051504013*1802051504013*NPort IA5000A-I/O Series NPort IAW5000A-I/O Series Quick Installation GuideVersion 2.1, January 2021Technical Support Contact Information/support2021 Moxa Inc. All rights reserved.OverviewThe NPort IA5000A-I/O and IAW5000A-I/O Series consist of serial device servers with Digital Input/Output (DIO), providing maximum flexibility to integrate serial equipment in the field into Ethernet networks for a variety of industrial data acquisition applications. The DIO on a device can be controlled over TCP/IP, using the Modbus TCP protocol, and it can be configured and secured from a web browser.Package ChecklistBefore installing the NPort IA5000A-I/O or NPort IAW5000A-I/O Series device server, verify that the package contains the following items: •NPort IA5000A-I/O or NPort IAW5000A-I/O device server with digital I/O•Antenna (for the NPort IAW5000A-I/O Series)•Quick installation guide (printed)•Warranty cardOptional Accessories•Mini DB9F-to-TB Adapter: DB9-female-to-terminal-block adapter for RS-422/485 applications•WK-51-01: Wall-mounting kit•DR-4524: 45W/2A DIN-rail 24 VDC power supply with universal 85 to 264 VAC input•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with universal85 to 264 VAC input•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to 132 VAC or 176 to 264 VAC input, selected by a DIP switchNotify your sales representative if any of the above items are missing or damaged.Hardware IntroductionAs shown in the following figures, the NPort IA5000A-I/O Series has two Ethernet RJ45 LAN ports, and the NPort IAW5000A-I/O Series has one Ethernet RJ45 LAN port and one antenna for WiFi (IEEE 802.11 standards) signal communication, supporting 2.4GHz and 5 GHz frequencies. Both series are equipped with four DIs and two DOs for data acquisition applications. The NPort IA5000A-I/O and IAW5000A-I/O device server series come with built-in 4 kV serial port surge protection.NPort IA5000A-I/O SeriesThe mechanical design of the NPort IA5000A-I/O Series is mostly identical; only the number of serial ports and number of DI/DO channels differ.NPort IAW5000A-I/O SeriesThe mechanical design of the NPort IAW5150A and the NPort IAW5250A is mostly identical; only the number of serial ports and number of DI/DO channels differ.LED IndicatorsName Color FunctionPWR 1, PWR 2 Green Power is being supplied to power input PWR1, PWR2.Ready Red Steady on Power is on, and the NPort isbooting up.Blinking Indicates an IP conflict, or theDHCP or BOOTP server did notrespond properly, or a relayoutput occurred.When the above two conditionsoccur at the same time.Check the relay output first. If theReady LED is still blinking afterresolving the relay output, thenthere is an IP conflict, or the DHCPor BOOTP server did not respondproperly.FlashingquicklymicroSD card failedGreen Steady on Power is on, and the NPort isfunctioning normally.Blinking The device server has beenlocated by Administrator’sLocation functionOff Power is off, or a power error condition exists.WLAN (Only for the NPortIAW5000A-I/O) Green Steady on Wireless is enabledBlinking NPort can’t establish WLANconnection with AP(Infrastructure) or station(Ad-Hoc)Off Wireless is not enabled.Signal Strength (3 LEDs only for the NPortIAW5000A-I/O) Green 1 Bottom The signal strength (RSSI) is lessthan -74 dBm2 Middle The signal strength (RSSI) isbetween -65 to -74 dBm3 Top The signal strength (RSSI) isgreater than -65 dBmEthernet Amber 10 Mbps Ethernet connectionGreen 100 Mbps Ethernet connectionOff The Ethernet cable is disconnected or has ashort.P1, P2 (Serial) Amber Serial port is receiving data.Green Serial port is transmitting dataOff No data is being transmitted or receivedthrough the serial port.DI Green DI status onOff DI status offDO Green DO status onOff DO status offHardware Installation ProcedureSTEP 1: After unpacking the unit, connect the power supply to the unit. STEP 2: Use an Ethernet cable to connect the unit to the network. STEP 3: Connect your device to the desired port on the unit.STEP 4: Place or mount the unit. The unit may be placed on ahorizontal surface such as a desktop, or mounted on the wall. Mounting OptionsThe NPort IA5000A-I/O and IAW5000A-I/O are designed to be attached to a DIN rail or mounted on a wall.STEP 1: Insert the top of the DIN rail into the slot. STEP 2: The DIN rail attachment unit will snap into place as shown at right.Wall Mounting (optional)For some applications, it may be more convenient to mount the NPort IA5000A-I/O or IAW5000A-I/O to a wall, as illustrated below.Do not drive the screws in all the way—leave a space of about 2 mm to allow room for sliding the wall-mounting panel between the wall and the screws.NOTE Test the screw head and shank size by inserting the screws into one of the keyhole-shaped apertures of the wall-mounting platesbefore they are fixed to the wall.STEP 3: Once the screws are fixedinto the wall, insert the four screwheads through the large openingof the keyhole-shaped apertures,and then slide the NPortdownwards, as indicated to theright. Tighten the screws for addedstability.Termination Resistor and Adjustable Pull-Up/Down ResistorsIn some critical environments, you may need to add termination resistors to prevent the reflection of serial signals. When using termination resistors, it is important to set the pull-up/down resistors correctly so that the electrical signal is not corrupted. The NPort IA5000A-I/O andIAW5000A-I/O Series use DIP switches to set the pull-up/down resistor values for each serial port. The DIP switches are located at the side of wireless device server for easy setting.To add a 120 Ω termination resistor, set switch 3 on the port’s assigned DIP switch to ON; set switch 3 to OFF (the default setting) to disable the termination resistor.To set the pull-up/down resistors to 150 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to OFF. This is the default setting.To set the pull-up/down resistors to 1 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to ON.Pull-Up/Down Resistors for the RS-485 PortSW1 (Serial 1) SW2 (Serial 2)DIP 1Pull-up resistorDIP 2Pull-down resistorDIP 3Terminal resistorON 1 KΩ 1 KΩ120 ΩOFF (Default) 150 KΩ150 KΩN/A NOTE Do not use the 1 KΩ setting while in RS-232 mode. Doing so will degrade the RS-232 signals and reduce the effectivecommunication distance.Software Installation InformationFor software installation, download the relative utilities from Moxa’s website:https:///support/support_home.aspx?isSearchShow=1•Download the NPort Windows Driver Manager and install it as the driver to run with Real COM mode of the NPort Series.•Execute NPort Windows Driver Manager; then map the virtual COM ports on your Windows platform.•You may refer to the DB9 Male pin assignment section to loop back pin 2 and pin 3 for the RS-232 interface to carry out a self-test on the device.•Use HyperTerminal or a similar program (you may download Moxa’s program, called PComm Lite) to test whether the device is good or not.Setting the IP AddressThe factory default IP settings are assigned as follows:NPort IA5000A-I/O SeriesLAN IP NetmaskStatic 192.168.127.254 255.255.255.0NPort IAW5000A-I/O SeriesLAN IP NetmaskStatic 192.168.126.254 255.255.255.0WLAN IP NetmaskStatic 192.168.127.254 255.255.255.0If the NPort is configured for DHCP but the DHCP server cannot be found, the NPort will use factory default IP settings.NOTE If you have forgotten the NPort’s IP address, use the Device Search Utility from your PC to locate the NPort. After searchingthe LAN for NPort units, the Device Search Utility will display theIP address of each unit.NOTE (For the NPort IAW5000A-I/O Series)Ethernet Bridge Disabled (default): Only one networkinterface can be active at a time. If the Ethernet link is active, theWLAN will be inactive. If the WLAN is active, the Ethernet link willbe inactive.Ethernet Bridge Enabled: The LAN and WAN will both beactive. Go to the web console, find the network settings page,and set Ethernet Bridge to Enabled.Open the web console to make the configuration changes as follows: STEP 1: Open your web browser.STEP 2: In the address bar, enter the default IP address (for the NPort IA5000A-I/O Series, it is 192.168.127.254; for the NPort IAW5000A-I/O Series, it is 192.168.126.254)STEP 3: The web server will ask for the username and password before you log in. To configure the device server, you may use the default user/default password admin /moxa to log in the web console.STEP 4: For first-time use, click the Wizard in the left navigation panel. The wizard will prompt you to configure the IP address and basic settings. For other settings, use the factory defaults or modify the settings for your application.Pin AssignmentsRJ45 (LAN) PinLAN 1Tx+ 2Tx- 3Rx+ 4– 5– 6Rx- 7– 8 –DB9 Male (RS-232/422/485) PinRS-232 RS-422/RS-485-4W RS-485-2W 1DCD TxD-(A) – 2RxD TxD+(B) –3 TxD RxD+(B) Data+(B) 4DTR RxD-(A) Data-(A) 5GND GND GND 6DSR – – 7RTS – – 8CTS – – 9 – – –Power Input and Relay Output PinoutsV2+ V2- V1+ V1- DC Power Input 2 DC Power Input 2 N.O. Common N.C. DC Power Input 1 DC Power Input 1DI/DO PinoutsDO0 DO1 GND DI0 DI1 DI2 DI3 COM GND Digital Output 0 Digital Output 1 Ground Digital Input 0 Digital Input 1 Digital Input 2 DigitalInput 3 Common GroundSpecificationsPower Input12 to 48 VDC Power Consumption NPort IA5000A-I/O: 300 mA @ 12 VNPort IAW5000A-I/O: 300 mA @ 12 VOperating Temperature Standard models:0 to 60°C (32 to 140°F)Storage Temperature-40 to 85°C (-40 to 185°F)Operating Humidity 5 to 95% RHDimensions (W x D x H) NPort IA5000A-I/O:59.6 x 101.4 x 134 mm (2.35 x 4.0 x 5.28 in)IAW5000A-I/O:59.6 x 101.4 x 134 mm (2.35 x 4.0 x 5.28 in)Magnetic Isolation 1.5 kV for EthernetRegulatory Approvals EMCCE: EN 61000-6-2/6-4FCC: FCC Part 17 Subpart B, Class AFCC Part 15 Subpart B, Class ASafetyUL: UL 60950-1LVD: EN 60950-1DSPR: ARIB-STD 33, ARIB-STD 66Fault Relay Circuit 3-pin circuit with current-carrying capacity of2 A @ 30 VDCATTENTIONThis equipment is intended to be used in Restricted AccessLocation.WARNING:HOT SURFACE. DO NOT TOUCH! Before touching the surface, pay special attention and take the necessary protection measures.。
网动远程视频会议系统安装使用手册
目录1 概述..................................................... 错误!未定义书签。
网动公司简介..................................... 错误!未定义书签。
Active Meeting 简介.............................. 错误!未定义书签。
Active Meeting (会议室版)特点.................... 错误!未定义书签。
2 手册阅读方法............................................. 错误!未定义书签。
标记方式......................................... 错误!未定义书签。
文本标记..................................... 错误!未定义书签。
图标......................................... 错误!未定义书签。
3 基本概念阐述............................................. 错误!未定义书签。
4 详细功能阐述............................................. 错误!未定义书签。
服务器端功能介绍................................. 错误!未定义书签。
服务器程序功能............................... 错误!未定义书签。
系统管理员后台功能介绍....................... 错误!未定义书签。
公司管理员后台功能介绍....................... 错误!未定义书签。
主持人后台功能介绍........................... 错误!未定义书签。
Moxa ioLogik E2200 Series智能以太网远程I O产品说明书
ioLogik E2200SeriesSmart Ethernet remote I/O with Click&Go LogicFeatures and Benefits•Front-end intelligence with Click&Go control logic,up to24rules•Active communication with MX-AOPC UA Server•Saves time and wiring costs with peer-to-peer communications•Supports SNMP v1/v2c/v3•Friendly configuration via web browser•Simplifies I/O management with MXIO library for Windows or Linux•Wide operating temperature models available for-40to75°C(-40to167°F)environmentsCertificationsIntroductionMoxa’s ioLogik E2200Series Ethernet Remote I/O is a PC-based data acquisition and control device that uses proactive,event-based reporting to control I/O devices and features the Click&Go programming interface.Unlike traditional PLCs,which are passive and must poll for data,Moxa’s ioLogik E2200Series will,when paired with our MX-AOPC UA Server,communicate with SCADA systems using active messaging that is pushed to the server only when state changes or configured events occur.Additionally,the ioLogik E2200features SNMP for communications and control using an NMS(Network Management System),allowing IT professionals to configure the device to push I/O status reports according to configured specifications.This report-by-exception approach,which is new to PC-based monitoring,requires far less bandwidth than traditional polling methods.PC-Free Alarm and Control IntelligenceThis device supports simple yet powerful Click&Go™technology toconfigure event-driven reports and alarms delivered over email,TCP/UDP,or SNMP traps,giving you a powerful and effective tool fordelivering timestamped status updates in real time.With built-in Click&Go™intelligence,this device can be configuredfor simple outputs paired up with simple input triggers without theneed for a PC controller.This allows it to be configured toautomatically report I/O events according to conditions specified bythe user.SNMP for Ethernet Device ManagementBy using SNMP,IT engineers can configure the device to deliver alarms(traps)for specific I/O events,or use it to read or write directly to the I/O registers.For the strongest security,the device features SNMPv3,with authentication and encryption.With Moxa’s SNMP-capable I/O,even IT professionals can easily integrate industrial sensors and servos over an Ethernet backbone,and with its strong network management tools,it is ideal for a wide variety of industrial applications,including environmental monitoring,telecommunications,power production and delivery,and transportation.Push Technology for Events and AlarmsWhen used with MX-AOPC UA Server,devices can use active pushcommunications when communicating changes in state and/orevents to a SCADA system.Unlike a polling system,when using apush architecture for communications with a SCADA system,messages will only be delivered when changes in state or configuredevents occur,resulting in higher accuracy and lower amounts of datathat need to be transferred.SpecificationsControl LogicLanguage Click&GoInput/Output InterfaceDigital Input Channels ioLogik E2210Series:12ioLogik E2212Series:8ioLogik E2214Series:6Digital Output Channels ioLogik E2210/E2212Series:8ioLogik E2260/E2262Series:4Configurable DIO Channels(by software)ioLogik E2212Series:4ioLogik E2242Series:12Relay Channels ioLogik E2214Series:6Analog Input Channels ioLogik E2240Series:8ioLogik E2242Series:4Analog Output Channels ioLogik E2240Series:2RTD Channels ioLogik E2260Series:6Thermocouple Channels ioLogik E2262Series:8Buttons Reset buttonRotary Switch0to9Isolation3k VDC or2k VrmsDigital InputsConnector Screw-fastened Euroblock terminalSensor Type ioLogik E2210Series:Dry Contact and Wet Contact(NPN)ioLogik E2212/E2214/E2242Series:Dry Contact and Wet Contact(NPN or PNP) I/O Mode DI or event counterDry Contact On:short to GNDOff:openWet Contact(DI to GND)On:0to3VDCOff:10to30VDCCounter Frequency900HzDigital Filtering Time Interval Software configurablePoints per COM ioLogik E2210Series:12channelsioLogik E2212/E2242Series:6channelsioLogik E2214Series:3channelsDigital OutputsConnector Screw-fastened Euroblock terminalI/O Type SinkI/O Mode DO or pulse outputCurrent Rating200mA per channelPulse Output Frequency1kHzDIO Output Leakage Current 4.0mA@24VDCOver-Current Protection0.65A per channel@25°COver-Temperature Shutdown175°C(min.)Over-Voltage Protection45VDC(typical)RelaysConnector Screw-fastened Euroblock terminalType Form A(N.O.)power relayI/O Mode Relay or pulse outputPulse Output Frequency0.3Hz at rated loadContact Current Rating Inductive load:2A@30VDC,250VAC,110VACResistive load:5A@30VDC,250VAC,110VACMinimum Permitted Load1A@5VDCContact Resistance100milli-ohms(max.)Electrical Endurance100,000operations@5A resistive loadMechanical Endurance1,000,000operationsNote Ambient humidity must be non-condensing and remain between5and95%.The relaysmay malfunction when operating in high condensation environments below0°C. Analog InputsConnector Screw-fastened Euroblock terminalI/O Mode Voltage/CurrentI/O Type DifferentialResolution16bitsInput Range ioLogik E2240Series:±150mV,±500mV,±5V,±10V,0to20mA,4to20mAioLogik E2242Series:±150mV,0to150mV,±500mV,0to500mV,±5V,0to5V,±10V,0to10V,0to20mA,4to20mAAccuracy ioLogik E2240/E2242:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2240-T/E2242-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CSampling Rate ioLogik E2240Series:All Channels:10samples/sec for voltage;6samples/sec for currentPer Channel:1.25samples/sec for voltage;0.75samples/sec for currentSingle channel:1.25samples/sec for voltage;0.75samples/sec for currentioLogik E2242Series:All channels:32samples/secPer channel:8samples/secSingle channel:100samples/secBuilt-in Resistor for Current Input120ohmsInput Impedance ioLogik E2240Series:900kilo-ohms(min.)ioLogik E2242Series:200kilo-ohms(min.)Over-Voltage Protection-25to+30VDC(power on)-35to+35VDC(power off)Analog OutputsConnector Screw-fastened Euroblock terminalI/O Mode Voltage/CurrentOutput Range0to10VDC4to20mAResolution12-bitAccuracy ioLogik E2240:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2240-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CLoad(Current Mode)Internal power:250ohms(max.)RTDsConnector Screw-fastened Euroblock terminalSensor Type JPT100,JPT200,JPT500(-200to640°C)JPT1000(-200to350°C)NI100,NI200,NI500(-60to250°C)NI1000(-60to150°C)NI120(-80to260°C)PT1000(-200to350°C)PT50,PT100,PT200,PT500(-200to850°C)Resistance of310,620,1250,and2200ohmsInput Connection2-or3-wireSampling Rate All channels:12samples/secPer channel:2samples/secResolution0.1°C or0.1ohmsAccuracy ioLogik E2260:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2260-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CInput Impedance625kilo-ohms(min.)ThermocouplesConnector Screw-fastened Euroblock terminalSensor Type J,K,T,E,R,S,B,NMillivolt Type±19.532mV±39.062mV±78.126mVFault and over-voltage protection:-35to+35VDC(power off);-25to+30VDC(poweron)Resolution16bitsMillivolt Accuracy ioLogik E2262:±0.1%FSR@25°C±0.3%FSR@-10to60°CioLogik E2262-T:±0.1%FSR@25°C±0.3%FSR@-10to60°C±0.5%FSR@-40to75°CTC Accuracy Types J,T,E,S,B:±5°CTypes K,R,N:±8°CCJC Accuracy±0.5°C@25°C±1.5°C@-40to75°CSampling Rate All channels:12samples/secPer channel:1.5samples/secInput Impedance1mega-ohms(min.)LED InterfaceLED Indicators PWR,RDY,Serial,I/O StatusEthernet Interface10/100BaseT(X)Ports(RJ45connector)1Magnetic Isolation Protection 1.5kV(built-in)Ethernet Software FeaturesConfiguration Options Windows Utility(ioAdmin),Web Console(HTTP)Industrial Protocols Modbus TCP Server(Slave),SNMPv1/v2c/v3,SNMPv1Trap,Moxa AOPC(Active Tag),MXIO Library,CGI commandsManagement BOOTP,IPv4,SMTP,DHCP Client,HTTP,TCP/IPMIB Device Settings MIBTime Management SNTPSecurity FunctionsAuthentication Local databaseEncryption HMACSecurity Protocols SNMPv3Modbus TCPFunctions Supported1,2,3,4,5,6,15,16Mode Server(Slave)Serial InterfaceConnector Terminal blockSerial Standards RS-485No.of Ports1Baudrate1200,2400,4800,9600,19200,38400,57600,115200bps Parity NoneData Bits8Stop Bits1Flow Control NoneSerial SignalsRS-485-2w Data+,Data-,GNDSerial Software FeaturesIndustrial Protocols Modbus RTU MasterPlatformReal-time Clock(RTC)Real-time clock with battery backupPower ParametersPower Connector Screw-fastened Euroblock terminalNo.of Power Inputs1Input Voltage12to36VDCPower Consumption ioLogik E2210Series:202mA@24VDCioLogik E2212Series:136mA@24VDCioLogik E2214Series:170mA@24VDCioLogik E2240Series:198mA@24VDCioLogik E2242Series:178mA@24VDCioLogik E2260Series:95mA@24VDCioLogik E2262Series:160mA@24VDCPhysical CharacteristicsDimensions115x79x45.6mm(4.53x3.11x1.80in)Weight250g(0.55lb)Installation DIN-rail mounting,Wall mountingWiring I/O cable,16to26AWGPower cable,16to26AWGHousing PlasticEnvironmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Altitude2000m1Standards and CertificationsSafety UL508EMC EN61000-6-2/-6-4EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:4kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:1kVIEC61000-4-6CS:10VIEC61000-4-8PFMFShock IEC60068-2-27Vibration IEC60068-2-6Freefall IEC60068-2-32DeclarationGreen Product RoHS,CRoHS,WEEEMTBFTime ioLogik E2210Series:213,673hrsioLogik E2212Series:217,722hrsioLogik E2214Series:307,329hrsioLogik E2240Series:155,941hrsioLogik E2242Series:204,391hrsioLogik E2260Series:327,282hrsioLogik E2262Series:341,063hrsStandards Telcordia SR332WarrantyWarranty Period ioLogik E2214Series:2years2ioLogik E2210/E2212/E2240/E2242/E2260/E2262Series:5years Details See /warrantyPackage ContentsDevice1x ioLogik E2200Series remote I/ODocumentation1x quick installation guide1x warranty card1.Please contact Moxa if you require products guaranteed to function properly at higher altitudes.2.Because of the limited lifetime of power relays,products that use this component are covered by a2-year warranty.DimensionsOrdering InformationModel Name Input/Output Interface Digital Input Sensor Type Analog Input Range Operating Temp.ioLogik E221012x DI,8x DO Wet Contact(NPN),DryContact–-10to60°CioLogik E2210-T12x DI,8x DO Wet Contact(NPN),DryContact–-40to75°CioLogik E22128x DI,4x DIO,8x DO Wet Contact(NPN or PNP),Dry Contact–-10to60°CioLogik E2212-T8x DI,4x DIO,8x DO Wet Contact(NPN or PNP),Dry Contact–-40to75°CioLogik E22146x DI,6x Relay Wet Contact(NPN or PNP),Dry Contact–-10to60°CioLogik E2214-T6x DI,6x Relay Wet Contact(NPN or PNP),Dry Contact–-40to75°CioLogik E22408x AI,2x AO–±150mV,±500mV,±5V,±10V,0-20mA,4-20mA-10to60°CioLogik E2240-T8x AI,2x AO–±150mV,±500mV,±5V,±10V,0-20mA,4-20mA-40to75°CioLogik E224212x DIO,4x AI Wet Contact(NPN or PNP),Dry Contact±150mV,0-150mV,±500mV,0-500mV,±5V,0-5V,±10V,0-10V,0-20mA,4-20mA-10to60°CioLogik E2242-T12x DIO,4x AI Wet Contact(NPN or PNP),Dry Contact±150mV,0-150mV,±500mV,0-500mV,±5V,0-5V,±10V,0-10V,0-20mA,4-20mA-40to75°CioLogik E22604x DO,6x RTD––-10to60°C ioLogik E2260-T4x DO,6x RTD––-40to75°C ioLogik E22624x DO,8x TC––-10to60°C ioLogik E2262-T4x DO,8x TC––-40to75°C Accessories(sold separately)SoftwareMX-AOPC UA Server OPC UA Server software for converting fieldbus to the OPC UA standard©Moxa Inc.All rights reserved.Updated May05,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
H3C S5120-EI系列以太网交换机 安装手册
iwifi安装及调试规范
爱WiFi业务AP(无线路由器)安装维护规范一、AP选择要点根据爱WiFi AP实景测试数据,选择爱WiFi AP（无线路由器）要依据客户现场环境而定。
1.1.平面覆盖式开放式大厅，覆盖半径10米，功率200毫瓦，内置环形天线或外置2天线放装AP（无线路由器）均可以胜任。
1.2.立体覆盖式开放式大厅，覆盖半径25米，要求上下层穿墙信号强度，推荐大功率功率吸顶式AP（无线路由），内置大功率发射天线，增加立体覆盖范围。
1.3.混合覆盖式若想使放装AP（无线路由器）增强信号或者增加覆盖面积，可使用增益天线，增益天线的作用跟天线多少是一样的，主要是稳定信号，增加平面覆盖范围。
而信号强度比如说穿墙后信号效果主要是由无线路由器的发送功率决定的，一般对正常人无害的最大值是20DB，还跟天线接受灵敏度有关系，灵敏度越高的，在信号强度很低的情况下依然可以捕捉信号，容易穿越障碍物体。
二、AP安装要点2.1.AP放置房间中间不管AP（无线路由器）放在哪，盲点都是不可避免的，而减少盲点的最佳位置就是把路由器放在房间中间。
如果路由器靠墙放置，无线信号不仅会被墙壁、门挡住，还会在角落里形成死角。
2.2.AP远离强电、强磁、强腐蚀干扰安装爱WiFi AP（无线路由器）位置必须保证无强电、强磁和强腐蚀性设备的干扰，如爱WiFi路由器安装位置的四周有特殊物品，如微波炉、无绳电话等他干扰源，建议AP 至少离开此类干扰源2～3 米。
2.3.AP安装场所干燥、通风、不易燃爱WiFi AP（无线路由器）安装场所应干燥、灰尘小、且通风良好，安装爱WiFi路由器的室内不得放置易燃品。
2.4.AP安装必须固定爱WiFi AP（无线路由器）壁挂安装在大楼墙面上，必须用固定架固定住，安装在天花板上，不允许悬空放置或直接扔在天花板上面。
2.5.AP POE（远程供电）距离不超60米在安装AP 设备时，POE供电模块跟AP 之间的最长距离60米，交换机与POE供电模块之间的最长距离80米。
IDAS远程I-O安装注意事项及要求
IDAS分散式智能数据采集网络（IDAS远程I/O）安装说明无锡贝尔自动化仪器仪表有限公司2007年2月IDAS 远程I/O 安装说明1．安装走线图：(见附页) 说明：A ． 图中IDAS 远程I/O 采用A 、B 双网通讯，互为冗余。
网络通讯线走线采用双向配置，锅炉、汽机两边分开。
具体走线方向不一定按图中标明的顺序排号，视现场要求决定，应以长度最短为最佳。
B ． IDAS 远程I/O 前置机根据现场要求，合理安装。
前置机安装位置应尽量远离带有强电工作的设备或变频器。
C ． 网络通讯线从IDAS 通讯转换口处引出，依次将现场前置机“串接”（其实是并接）起来，通讯线走至末端，在末端前置机通讯端子上加一匹配电阻便可。
匹配电阻为标准100Ω、1/4W 电阻。
D ． 通讯线严禁与动力电缆敷设在一起，应分层敷设（一般走信号电缆层）。
E ． 网络中A 网与B 网的通讯线不能交叉混接，敷设过程中应标明电缆进出走向，便于检查和维护。
2.前置机的外形尺寸A ． IDAS-2102测量前置机的信号线、通讯电缆均由下方密封橡胶头引入，必要时可以灌入密封胶，保证整机的密封性能，确保防尘、防潮的技术要求。
如图所示(黑色方块即为密封橡胶头)。
外壳上的信号接线记录用于用户自行标注信号名称和来源。
前置机地址1009出厂日期编号2019年月测点名称三0102通道通道IDAS信号接线记录表1211测点名称精IDAS-2102模拟量测量前置机江苏省无锡市阳山仪器仪表厂信号类型信号类型主处理系统接线板LED指示灯AC220V地 N L3．前置机的安装场机柜内。
但建议用户从长远利益考虑，前置机的安装、接线应利于日后的维护与保养。
4．前置机通讯线接线方法IDAS远程I/O通讯线分A网、B网二根，分别连接前置机通讯接线端子的A端、5．前置机通道接线方法每一台前置机通道信号可混接，即在同一台前置机内，可直接测量各种热电偶、热电阻等信号。
信号线单芯截面积应不大于1.8mm2前置机接线端子示意图：2007年2月。
Comtrol ES8108 ES8108F 工业以太网开关快速安装指南说明书
ROCKET LINX ES8108Industrial Ethernet SwitchIntroductionThe RocketLinx ES8108 and ES8108F series of industrial Ethernet switches conform toIEE802.3 and 802.3u standards. This series includes the following models:• ES8108 supports eight 10/100BASE-TX ports• ES8108F-M (Multi-Mode) supports six 10/100BASE-TX and two 100BASE-FX fiber ports • ES8108F-S (Single-Mode) supports six 10/100BASE-TX and two 100BASE-FX fiber portsThe ES8108/ES8108F feature an IP31 rated compact metal housing for operation in harsh environments. The series also features an alarm relay output to notify users of a port link or power failure that can be enabled or disabled using the 9-pin DIP switch. The ES8108/8108F can be powered using a wide input power range of 10-60VDC using the 6-pin terminal block.See the Comtrol website for complete product specifications.Wiring the Power InputsThe ES8108/ES8108F provides:• Power redundancy and reverse polarity protection (PW1/PW2). If both power inputs are connected, the ES8108/ES8108F is powered from the highest connected voltage.• Positive or negative power source. If using redundant power supplies, they must be inthe same mode.• An alarm if PW1 or PW2 are no longer receiving power.Use this procedure to wire the power:1. Insert the positive and negative wires into the + and - contacts on the PW1 or PW2 on the terminal block connector.2. Tighten the wire-clamp screws to prevent the wires from being loosened.Note: Power should be disconnected from the power supply before connecting it to the switch. Otherwise, your screwdriver blade can inadvertently short your terminal connections to the grounded enclosure.If this is a Restricted Access Location installation, make sure that the power supply is in compliance with a UL certified LPS (limited power source) and thepower system is shutdown to avoid any damage while connecting the power.Grounding the ES8108/ES8108FThere is an earth ground screw on the bottom of the ES8108/ES8108F. Connect the earth ground screw of the switch to a grounding surface to ensure safety and prevent noise.Earth Ground ScrewEarth GroundWarning: Do not connect to AC line – NeutralDC Power OutputPower Supply 10-60VDC (UL Listed)10-60VDCV-V+LAC Power Input NVerify the Power Input requirements on the product label.V-V+Power Supply 10-60VDC (UL Listed)LAC Power Input NDC Power Output10-60VDC12-24AWG12-24AWGDry Relay OutputPWR 1PWR 2Setting the DIP Switch1 to 8 (Port)9 (Power)On Enables the port link down alarm for the corresponding port. On Enables the power failure alarm.Off Disables the port link down alarm for the corresponding port. Off Disables the power failure alarm.Wiring the Alarm Relay OutputThe alarm relay output contacts are in the middle of the terminal block connector. By inserting the wires and setting the DIP switch of the respective Port Alarm to “ON”, the alarm relay output detects any port failures and forms a short circuit. The alarm relay output is “Normal Open.” The alarm relay output closes if there is a port or power failure.Maximum 0.5A/24VDCPW1AlmPW2Alarm Controlport 1~8powerAlarmSystemExtra PowerSystemMounting the SwitchMount the ES8108/ES8108F on the DIN rail using the DIN rail clip that is attached to the rear of the unit.RXTXRXTXCable Wiring(SC to SC)RX A TX BTX A RX B A BConnecting to the NetworkConnecting the Ethernet PortsConnect one end of an Ethernet cable into the Ethernet port of the ES8108/ES8108F and the other end to the attached device. All Ethernet ports support auto MDI/MDIX functionality.Always make sure that the cables between the switches and attached devices (for example, switch, hub, or workstation) are no more than 100 meters (328 feet). The cable must meet EIA/TIA-568 100-ohm specifications:• 10BASE-T: 2-pair UTP/STP Category 3, 4, 5, or 5e • 100BASE-TX: 2-pair UTP/STP Category 5 or 5e Connecting the Fiber Ports (ES8108F) Connect the fiber port to another Fiber Ethernet device using the following diagram.An improper connection will cause the fiber port not to work properly. The fiber port is a standard or square connector (SC).This is a Class 1 Laser/LED product.Don't stare into the Laser/LED Beam.！3 TD+6 TD- 3 RD+6 RD-Switch Router or PC 1 RD+2 RD-1 TD+2 TD-Straight-Through Cabling Schematic 3 TD+6 TD- 3 TD+6 TD-Switch Switch 1 RD+2 RD-1 RD+2 RD-Crossover Cabling SchematicNote: In the IEEE standard, it suggests the available transmission distance is 2km for 62.5/125um fiber optical cable in 1310nm wave length. Actually, the attenuation of Multi-Mode 62.5/125um optical fiber cable is 1.5dBm/km and the maximum link distance can up to 4 to 5km.The IEEE organization recommends maximum optical fiber cable distances as defined in the following table.Fiber TransceiverMode Cable Type Wavelength Transmit Power (Min.) Transmit Power (Max.) Receive Sensi vity (Max.) ReceiveSensi vity(Min.)Min. LaunchPower –Max.ReceiveSensi vityDistance (km)Mul50/125um 62.5/125um1310nm -20dBm -14dBm -31dBm 0dBm 11dBm 2kmNote (below)Single 8-10/125um 1310nm -15dBm -8dBm -34dBm -8dBm 19dBm30kmStandard Data Rate (Mbps)Cable TypeIEEE StandardDistance10BASE-FL10850nm, 50/125um or 62.5/125um Mul -Mode op cal fiber cable 2km100BASE-FX1001310nm, 50/125um or 62.5/125um Mul -Mode op cal fiber cable 2km100BASE-SX100850nm, 50/125um or 62.5/125um Mul -Mode op cal fiber cable300mOptical Fiber Cable Attenuation* These values are per TIA/EIA and other industrial specifications.** These values are one example of the performance that can be obtained with a new fiber installation.LED IndicatorsThere are system diagnostic and Ethernet port LEDs located on the front panel of the ES8108/ES8108F.Fiber Type Wavelength A enua on/km *A enua on/km ** Connector Loss Splice lossMul -Mode 50/125um 850nm 1310mm 3.5dBm 1.5dBm 2.5dBm 0.8dBm 0.75dBm 0.1dBm Mul -Mode 62.5/125um 850nm 1310nm 3.5dBm 1.5dBm 3.0dBm 0.7dBm 0.75dBm 0.1dBm Single-Mode 9/125um 1310nm 0.4dBm 0.35dBm 0.75dBm 0.1dBm Single-Mode 9/125um 1550nm0.3dBm0.22dBm0.75dBm0.1dBmLED LED LitLED O ffPWR 1/PWR2PoweredNo powerAlm (Alarm) Port link is down or a power failure event has occurred. Not ac vatedPort 1- 8 (ES8108)Port 1- 6(ES8108F-S or ES8105F-M)A green lit LED indicates that a network device is detected and linked up.A yellow lit LED indicates that a network device is detected and link established at 100Mbps.If the green Link LED is lit and the yellow speed LED is o ff, a network device is detected and a link has been established at 10Mbps.Both green and yellow LEDs are not lit a port link has not been established.Fiber Ports 7- 8 (ES8108F)A green lit LED indicates that a network device is detected anda link has been established at 100Mbps.No ac ve linkPacket Forwarding AbilityThe ES8108/ES8108F features a packet filtering function for broadcast packet control protection and Quality of Service (QoS). Both features can provide higher performance in a crowded network through traffic filtering and prioritizationBroadcast ControlThe ES8108/ES8108F begins to drop broadcast packets with DA (destination address) equal to FF:FF:FF:FF:FF:FF if the received broadcast packets are more than the threshold, 198 packets/per second at 100Mbps or 19 packets/per second at 10Mbps link speed.All ports are enabled with this function by default to provide better network performance and prevent congestion caused by the flooding of broadcast packets.Quality of ServiceThe ES8108/ES8108F supports the frame type priority function, where high priority packets will be queued to a high priority queue to share more bandwidth. The ratio of bandwidth of the high priority to the low priority queue is 8:1. After 8 high priority packets are processed, then 1 low priority packet is processed. Both the ES8108 and ES8108F can examine the specific bits of VLAN Tag and TCP/IP TOS of IPv4 and IPv6.Comtrol Customer Service。
EIO说明书
EIO远程IO联网设备说明书(Ver2.6)一、产品说明 (3)1．EIO介绍 (3)2．的优势及应用范围 (4)二、使用及配置 (5)1、快速安装 (5)1.最小系统需求 (5)2.安装 (5)3.检查EIO运行状态 (6)4.安装使用虚拟串口软件 (7)5.恢复出厂值 (10)6.设备配置 (10)2、网络参数设置 (11)3、配置EIO (11)4、EIO控制协议 (12)5、注意事项 (12)6、免责声明 (12)三、常见问题 (13)四、保修服务及技术支持。
(13)1、免费保修 (13)2、免费保修服务方式 (13)3、不属于免费保修的情况 (14)23一、一、 产品说明产品说明1． EIO 介绍介绍EIO 是同时集成I/O 控制和RS232/RS485串口服务器的以太网设备，同时具备开关量输出、开关量采集、串口服务器等功能，可同时替代I/O 卡和串口服务器。
支持Socket、虚拟串口两种用户通讯接口，用户可以按照Socket 标准，通过TCP/IP 连接与EIO 进行通讯。
也可以通过VSPM 虚拟串口软件，将EIO 虚拟成普通串口设备，可以有效的降低软件编写难度。
EIO 采用国际通用的Modbus TCP 作为通讯协议，可以与各类组态软件无缝结合。
首创EIO Link 技术，互联2个EIO 设备，可以将远程的开关量状态传输到控制中心，并完整重现，控制中心的开关量状态也可以传输到现场，2个EIO 的串口也可以进行透明数据传输，整个控制过程无需电脑，完全由2个EIO 实现。
EIO 设备具备光电隔离、ESD 防护等多用防护措施，可以稳定的工作在恶劣环境中。
2．的优势及应用范围的优势及应用范围优势优势比传统的电脑+I/O控制卡结构功能更多，工作更稳定。
同时集成I/O控制和协议转发，性价比更高。
实用化设计，简化部署难度。
较高的附加值。
提供例子程序的源代码，以及各种开发支持。
应用范围应用范围基于Internet的智能家居，安防系统设计。
Moxa ioLogik E2200 系列乙太网络远程I O设备说明书
ioLogik E2200系列具備Click&GO邏輯的智慧乙太網路遠端I/O特色與優點•具備專利Click&Go控制邏輯的前端智慧，多達24項規則•與MX-AOPC UA伺服器進行的主動通訊•透過點對點通訊節省時間和接線成本•支援SNMP v1/v2c/v3•透過網頁瀏覽器輕鬆完成配置•使用Windows或Linux版MXIO程式庫簡化I/O管理•支援寬溫工作環境，適合-40至75°C（-40至167°F）環境認證簡介Moxa的ioLogik E2200系列乙太網路遠端I/O是PC型資料擷取和控制裝置，使用基於事件的主動報告來控制I/O裝置，並採用Click&Go程控介面。
不同於被動而且必須輪詢資料的傳統PLC，Moxa的ioLogik E2200系列與我們的MX-AOPC UA伺服器配對時，將使用主動訊息與SCADA系統進行通訊，該訊息僅在發生狀態變更或配置事件時推送到伺服器。
此外，ioLogik E2200配備使用NMS（網路管理系統）進行通訊和控制的SNMP，IT專業人員可以將裝置配置為按照已配置的規格推送I/O狀態報告。
這種在例外狀況發生時進行報告的方法是基於PC的監控的新方法，相較於傳統輪詢方法，這需要的頻寬更少。
免PC告警和控制智慧這個裝置支援簡單而強大的Click&Go™技術，可配置透過電子郵件、TCP/UDP或SNMP陷阱傳送的事件驅動報告和告警，為您提供強大而有效的工具，以即時傳送有時間戳記的狀態更新。
藉由內建的Click&Go™智慧，可以對於與簡單輸入觸發條件配對的簡單輸出配置這個裝置，而不需要PC控制器。
這個裝置由於這項特點而能夠按照使用者指定的條件自動報告I/O事件。
用於乙太網路裝置管理的SNMP藉由使用SNMP，IT工程師可以將裝置配置為針對特定I/O事件傳送告警(SNMP trap)，或用來直接讀取或寫入I/O暫存器。
EIO-8G光纤以太网远程IO联网产品安装指南_3776
EIO-8G光纤以太网远程IO联网产品安装指南一、基本硬件连接 (3)1、开关量输出端子（侧面绿色端子） (3)2、前面板视图 (5)3、开关量输入端子（前面板绿色端子） (5)4、串口功能 (6)5、电源输入 (8)6、光以太网接口 (9)7、光太网级联连接方式及优势 (11)二、检查运行状态 (12)三、使用Xframe软件 (13)1、首先以管理员权限运行Xframe安装文件，并安装软件 (13)2、选择默认的“我的设备”，然选择“扫描可识别网络设备” (13)3、修改设备IP (13)4、如果扫描不到设备 (13)5、退出设备探测器，在模块管理菜单里选择添加模块 (14)8、测试 (16)9、更改控制说明 (16)10、使用Telnet菜单管理此设备 (17)11、操作规则 (18)12、Xframe软件的基本功能 (19)四、测试、查看EIO-8G的控制通讯协议（Modbus TCP） (20)1、概述 (20)2、安装测试软件Modbus测试软件(modpoll) (20)3、选择Modbus Poll连接 (20)4、定义Modbus基本信息 (20)5、开关量输入定义 (21)6、开关量输出定义 (23)7、更多的Modbus信息 (23)8、查看通讯报文 (23)五、测试查看Modbus RTU协议 (24)1、概述 (24)2、安装测试软件Modbus测试软件(modpoll) (24)3、通过DB9串口连接电脑与EIO-8G (24)4、选择Modbus Poll连接 (24)5、定义Modbus基本信息 (25)6、开关量输入定义 (25)7、开关量输出定义 (27)8、更多的Modbus信息 (28)9、查看通讯报文 (28)六、Modbus TCP协议参数 (29)1.Modbus TCP Server参数 (29)2.Modbus TCP Client参数 (30)七、EIO Link协议简介 (32)1.概述 (32)2.EIO Link协议默认参数 (32)3.报文格式 (32)4.协议样本及解释 (33)八、使用串口转以太网功能 (35)1、串口转以太网的默认设置 (35)2、使用方式 (35)3、建立虚拟串口 (35)4、测试虚拟COM口 (36)5、常见问题 (36)九、切换串口模式 (37)1、EIO-8G的串口模式 (37)2、更改RS232口模式为串口转以太网 (37)3、更改RS485口模式为控制本机硬件(Modbus RTU协议) (38)十、串口转以太网参数 (40)1、串口转以太网的数据模式 (40)2、Server模式参数 (40)3、Client模式参数 (42)4、Modbus TCP/RTU双向转换模式参数 (44)十一、配对使用2台EIO-8G (45)1、工作原理 (45)2、配置IP (45)3、配置Client (45)4、Server模式设置 (48)5、检查配对是否成功 (48)十二、1台EIO-8G与多台EIO-8G配对使用 (49)1、工作原理 (49)2、配置EIO-8G (49)3、配置作为从机的EIO-8G (50)十三、输入映射到输出功能 (51)1.概述 (51)2.输入对输出参数及说明 (51)十四、为继电器Output设置默认状态（输出保护） (53)1.概述 (53)2.输出保护参数及说明 (53)十五、恢复出厂值 (54)十六、EIO-8G设备性能指标 (55)十七、保修条款 (56)一、基本硬件连接1、开关量输出端子（侧面绿色端子）提供8路继电器触点输出。
controllogix-xt 高速数据通道 远程 i o 接口模块 安装指南说明书
安装指南ControlLogix-XT 高速数据通道 -远程 I/O 接口模块产品目录号 1756-DHRIOXT主题页码重要用户须知3关于 1756-DHRIOXT 模块8关于 ControlLogix-XT 系统10带传统 ControlLogix 组件的 ControlLogix-XT10开始之前的工作11设置网络类型和节点地址开关11准备安装模块要使用的机架12确定模块插槽位置13带电安装和取出模块13安装模块14取出或更换模块15接线模块通道的连接器16连接编程终端17连接 DH+ 或远程 I/O 网络18接通机架电源18检查电源和模块状态192 ControlLogix-XT 高速数据通道 - 远程 I/O 接口模块主题页码字母数字显示屏启动序列20电源状态21字母数字显示屏代码22状态指示器25通用技术参数 - 1756-DHRIOXT27环境规范 - 1756-DHRIOXT28认证 - 1756-DHRIOXT30其它资源31出版物 1756-IN638A-ZH-P - 2009年3 月ControlLogix-XT 高速数据通道 - 远程 I/O 接口模块 3 重要用户须知固态设备具有与机电设备不同的运作特性。
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (固态控制设备的应用、安装与维护安全指南，出版号：SGI-1.1，可向您当地的罗克韦尔自动化销售处索取或通过在线索取) 描述了固态设备和硬接线机电设备之间的一些重要区别。
由于存在这些区别，同时由于固态设备的广泛应用，负责应用此设备的所有人员都必须确保仅以可接受的方式应用此设备。
对于由于使用或应用此设备而导致的任何间接损失或连带损失，罗克韦尔自动化在任何情况下都不承担任何责任。
本手册中的示例和图表仅供说明之用。
AirEther RB-11 快速安装指南说明书
Configuration Preparation 1) Connect the antenna into “ ANT port” of the AirEther RB-11 via an antenna cable. (Antenna is purchased separately and is not included in the AirEther RB-11 package.) 2) Connect the AC power cord to the PoE (Power over Ethernet) power supply plug. 3) Connect one end of the supplied Ethernet cross-over cable (shorter length cable) into the “ data in” port of PoE power supply and the other end into the Ethernet port of the PC. 4) Connect by twisting the weather tight connector of the 30m length category 5 cable into LAN/WAN port of AirEther RB-11. 5) Connect the remaining side of PoE cable into “ power & data out” port of PoE power supply. 6) You don’t need to connect the RS232 console cable, it is only required for resetting your unit to factory default setting or viewing default network setting.
ICP DAS ET-7000系列以太网远程I O快速入门指南说明书
Congratulations on purchasing PET-7000/ET-7000 - the most popular automation solution for Ethernet remote monitoring and control application. This Quick Start Guide will provide information needed to get started with PET-7000/ET-7000. Please also consult the User Manual for detailed information on the setup and use of PET-7000/ET-7000.In addition to this guide, the package includes the following items:PET-7000/ET-7000 Module Software Utility CD- PET-7000 / ET-7000 Website/remote_ethernet_io_modules.html- ICP DAS USA Website/Phone : 1-310-517-9888Email: ********************Tech Support:*******************21-----------------------------------------------------------Configuring Boot ModeInit mode: For configuration. After booting, ET-7000 will not run thedefault firmware and cannot surf the internet. Use this mode toupdate MiniOS7 image.Normal mode: For normal working. After booting, ET-7000 will run thedefault firmware and can use all ET-7000 functions.---------------------------------------------------------------------------------- Connecting to Network, PC and PowerThe ET-7000 is equipped with an RJ-45 Ethernet port for connection to an Ethernet hub/switch and PC.3 4 ---------------------------------------------------------------------------------Installing the MiniOS7 UtilityThe MiniSO7 Utility can be obtained from companion CD or our site: CD:\Napdos\minios7\utility\minios7_utility\ /minios7utility.htmlAfter the installation has been completed, there will be a new short-cut for MiniOS7 Utility on the desktop.----------------------------------------------------------------------------------Using MiniOS7 Utility to Assign a New IPThe ET-7000 are Ethernet devices, which comes with a default IP address, therefore, you must first assign a new IP address to the ET-7000. The factory default IP settings are as follows:Double-click the MiniOS7 Utility shortcut on your desktop.After pressing F12 or choosing Search from Connection menu, the MiniOS7 Scandialog will appear, that will display a list of all the MiniOS7 modules on your network.See the status tip, waiting for the search to be done.Choose the module name for fields in the list, and then choose IP setting from the toolbar.After completing the settings, press the Yes button in the Confirm dialog box to exit the procedure.56---------------------------------------------------------------------------------- Enabling Adobe Flash Player in Your BrowerYour browser must support Adobe Flash Player and have it enabled in order to use theET-7000 web site.If you do not have it installed, please go to the following website and install it.The Adobe Flash Player Download Center:/flashplayer/---------------------------------------------------------------------------------- Go to the ET-7000 Web Site to Check out FunctionsThe ET-7000 contains an advanced web configuration system that provides users with accessET-7000 applications through a standard web browser.Make sure the switch placed in the“ Normal” p osition.Then reboot ET-7000/PET-7000.Please use a standard internet browser to view the ET-7000 webpage, such as MozillaFirefox or Internet Explorer…etc.If you haven’t changed the default IP address of the ET-7000, please refer to “4. UsingMiniOS7 Utility to Assign a New IP” to configure it.After entering the IP address, the login dialog box will appear and prompt you to enter your username and password.The factory default user name and password are as follows (Case sensitive) :After logging into theET-7000 web site, thewelcome page willappear.Under the Main Menu, expand the Web HMI, and thenselect the Web HMI option to check the values of the data acquisition.。
EtherCAT 远程 I O 模块用户手册说明书
EtherCAT 远程I/O 模块用户手册V1.02018.1版权申明上海固高欧辰智能科技有限公司 保留所有权利上海固高欧辰智能科技有限公司保留在不事先通知的情况下，修改本手册中的产品和产品规格等文件的权力。
上海固高欧辰智能科技有限公司不承担由于使用本手册或本产品不当，所造成直接的、间接的、特殊的、附带的或相应产生的损失或责任。
上海固高欧辰智能科技有限公司具有本产品及其软件的专利权、版权和其它知识产权。
未经授权，不得直接或者间接地复制、制造、加工、使用本产品及其相关部分。
客户服务： 4006 300 321上海固高欧辰智能科技有限公司地 址：上海闵行区东川路555号4号楼1层 电 话：************ 54708786 传 真：************电子邮件：********************* 网 址：运动中的机器有危险！使用者有责任在机器中设计有效的出错处理和安全保护机制，上海固高欧辰智能科技有限公司没有义务或责任对由此造成的附带的或相应产生的损失负责。
文档版本前言感谢选用Softlink EtherCAT I/O数字量模块为回报客户，我们将以品质一流的IO模块、完善的售后服务、高效的技术支持，帮助您建立自己的控制系统。
·Softlink产品的更多信息上海固高欧辰智能科技有限公司的网址是。
在我们的网页上可以得到更多关于公司和产品的信息，包括：公司简介、产品介绍、技术支持、产品最新发布等等。
您也可以通过电话（4006 300 321）咨询关于公司和产品的更多信息。
·技术支持和售后服务您可以通过以下途径获得我们的技术支持和售后服务：♦电子邮件：*********************♦电话：4006 300 321♦发函至：上海闵行区东川路555号4号楼1层上海固高欧辰智能科技有限公司♦邮编：200241·用户手册的用途用户通过阅读本手册，能够了解Softlink EtherCAT I/O数字量模块的基本结构和规格指示，正确安装扩展模块，完成扩展模块的基本调试。
Rarie PDU-16智能网络PDU详细安装指南与快速安装指南的PDF文件说明书
READ ME FIRST QUICK INSTALL GUIDEPDU 16Intelligent Network PDUPDU-16Includes:PDU 16 16-Outlet Intelligent Network PDUMounting KitFerrite RF ChokePower CordINSTALLATION AND SETUP 1Physical InstallationThe PDU 16 can be easily installed on any flat surface. Alternately, use the included hardware kit to attach the mounting clips to a wall or rack rail, then attach the PDU 16 to the mounting clips.n NOTE: To remove the PDU 16 from the mounting clips, wedge a flathead screwdriver between the side of the unit and clip, then gently pry the PDU from each of the clips.RackrailMounting BracketNutFixedMountingPosition ScrewMountingClipRack-Mounting the PDU 16Install the RF Choke on the Ethernet Cable3 Access and SetupGetting ConnectedIf the PDU 16 isn’t already connected to mains power, plug in the PDU. The PDU 16 is configured to use DHCP. Once initialized, the PDU 16 will power on all eight switched outlets in sequence and obtain an IP address from aDHCP server on the network.Using a computer or mobile device, log in to a router on the network and locate the PDU 16 in the router’s DHCP client reservation table. Alternately, you may also use a remote management system, IP scanner or a similar tool to find the PDU 16 on the network and determine its IP address. The PDU 16 can be identified by its DHCP client name, which will look like “PDU-16-78083E,” where the last half of the name represents the last three octects of the device’s MAC address. Once you locate it, make anote of the IP address. If the PDU 16 fails to find a DHCP server the unit will default to the IP address 192.168.0.6Logging InTo access the PDU 16 web UI, use a web browser on a computer or mobile device on the same network as the PDU 16. In the address field, enter the IP address you determined in the previous step. Log in tothe PDU 16 using the default user name and password:Username: adminPassword: adminSelect the menu items to view and/or modify the configuration. For more guidance on setup and configuration, refer to the product support resources at .4Hardware OperationFront PanelThe front panel of the PDU 16 includes the power supply inlet (with cable retainer), outlet status indicators, general status indicator, a reset button and an Ethernet port.Front Panel with Status Indicators, Ethernet port, and Reset ButtonEnd PanelThe end panel of the PDU 16, nearest the power supply inlet, features a circuit breaker and a grounding screw.End Panel with Ground Screw and Circuit BreakerLED IndicatorsThe LED indicators on the PDU 16 include a general device status LED, and a power status indicator for each of the eight controlled outlets.The following chart shows the LED indicators of the Volt along with anexplanation of the indicator’s properties:Reset ButtonThe Reset button (located adjacent the Ethernet port) is used to restore the PDU to factory default settings.X To Reboot the PDU: Remove the power supply cord from the PDU, wait five seconds, then reconnect the power supply cord to restore power.X To Restore Default Settings: With the PDU 16 powered on, use a pen orstylus to press and hold the Reset button on the back panel for at least six seconds, then release the button. The PDU automatically restores factory default settings and reboots. Once the Status LED indicates normal operation (see LED Indicators section), the PDU 16 is running again with factory defaults, including username and password and any IP configuration.n NOTE:P lease note that restoring Default Settings will remove any/ all custom configuration.3-Year Limited WarrantyThis Luxul™Return Material Authorization (RMA) number.please click here Luxul PDU warranty page online.Lifetime SupportLuxul offers free lifetime support of all products purchased through anthe website or the support section in the Dealer Portal, or to contact support, visit our Support Resources page online.Connected Equipment Protection Policy$25,000Warranty Luxul PDU warranty page online.SalesP: 801-822-5450 E:***************Technical SupportP: 801-822-5450 Option 3 E:*****************Copyright and Trademark Noticestrademarks and registered trademarks are property of their respective holders.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
E I O H F以太网远程I O联
网产品快速安装指南
The latest revision on November 22, 2020
EIO-HF以太网远程IO联网产品快速安装指南
1.基本硬件连接
开关量输出端子（绿色端子）
提供8路继电器触点输出。
2个接线端子为一个开关（Output1-8）。
每路开关最大负载：AC 250V/10A、AC 125V/30A、DC 30V/10A。
EIO开关量输出逻辑图。
EIO控制220V线路接线图。
开关量输入端子（黄色端子）
由板子提供一个开关量检测信号（COMM脚），当此检测信号与开关量输入端（Input1-8）中的任何一个接通时，此开关量输入端为接通状态，检测
数据字节对应位被置1，否则为0。
温湿度传感器接口
建议使用或以上线径的4芯屏蔽线或4芯护套线，连接EIO-HF和温湿度传感器探头。
最远通讯距离可达15米。
不可使用网线作为通讯线。
电源输入
DC12V 500mA端子式电源输入，请按照外壳文字说明连接电源正负极。
使用过程中，如果由于供电电源超过上述规定而造成的损失，不在免费保修范围之内。
RS232/RS485接口
UART端口的1、9脚分别对应RS485的A+、B-。
UART端口的2、3、5分别对应RS232的收、发、地。
控制通讯方式及协议
<通过以太网&TCP/IP控制>：此模式为默认模式，通过TCP/IP Modbus TCP 通讯协议进行控制，设备监听在502端口，具体报文格式及内容，请查看光盘内的《EIO技术配置手册》，或使用光盘内的演示软件查看控制报文。
应用软件可以使用Socket规范与EIO建立用于控制通讯TCP/IP连接。
也可以VSPM软件，将EIO映射成本机的虚拟COM，应用软件采用串口编程方式与EIO进行控制通讯。
RS232协议转换
RS232协议转换默认TCP/IP监听端口为6020，连接到此端口，或将此端口映射成虚拟串口，即可通讯。
RS485协议转换
RS485协议转换默认TCP/IP监听端口为6021，连接到此端口，或将此端口
映射成虚拟串口，即可通讯。
网络
设备支持10Mbps以太网接入，不支持网线自动翻转，如果与网卡连接，需
要使用交叉网线。
与交换机或集线器连接，使用普通的568B/A网线即可。
2.检查运行状态
上电后就可以观察设备的工作状态。
正常情况下，<Work>指示灯每隔一秒闪烁一次，长亮或长灭都为不正常状态。
以太网连接正常时<联接>指示灯将长亮。
其他状态，参考下面的指示灯含义说明。
Data：网络数据，以太网连接有数据传输时闪烁。
Link：网络连接，以太网连接正常时为长亮。
Work：正常启动并工作后，每隔一秒闪烁一次，长亮或长灭都为故障状
态。
UART：当与虚拟串口软件或其他控制软件建立连接后为长亮状态，在串口
转TCP/IP透明数据时，此指示灯转换为数据转发指示。
CMD：每执行一次远程控制命令，此指示灯闪烁一次。
PWR：正常时为长亮状态。
3.EIO Link技术
2个EIO设备可以通过EIO Link技术配置成对联模式。
此模式特点：
EIO-A的开关量输入状态将被复制到EIO-B开关量输出
EIO-B的开关量输入状态将被复制到EIO-A开关量输出
EIO-A与EIO-B的串口协议转换功能也可以设置为透明传输模式。
EIO出厂时，均为EIO Link的<EIO Link Server模式>，所以一个EIO使用默认设置，另一个使用<EIO Link Client模式>就可以完成对联。
EIO-A使用默认设置，工作在<EIO Link Server模式>。
在EIO-B的<EIO
Link>菜单中，设置为<EIO Link Client模式>，并将EIO-B的远程服务器地址设置为EIO-A的IP地址，就可以完成对联设置。
EIO Link模式有效情况下，Modbus TCP的开关量输出控制功能将被禁用，但是可以轮询EIO的开关量输入状态。
4.开关量状态主动上传功能配置
启用EIO Link的<EIO Link Server模式>（默认已经启用）
使用TCP/IP协议连接EIO的5100端口，或将此端口映射成虚拟串口。
当开关量发生变化时，可以从此TCP/IP连接，或虚拟串口接收到状态数
5.安装VSPM虚拟串口软件
1)安装光盘或从网络下载的VSPM虚拟串口软件。
2)EIO默认设置为Server模式，所以择VSPM的Client模式（默认模式）。
3)选择<使用设备探测器建立虚拟串口>，进入主界面后，选择<扫描添加设
备>
4)修设备IP地址
选择一个扫描到的设备
在<IP地址>输入栏中，为设备指定一个新的可访问的IP地址
单击<修改设备网络参数>，设备修改IP地址为指定地址，并自动重启用于应用设置
启动完毕后单击<搜索设备>，就可以看到设备已经修改为新的IP地址。
5)选择映射此设备端口，就可以自动映射出对应的虚拟串口
设备的RS232协议转换端口被映射到COM2，对应:6020
设备的RS485协议转换端口被映射到COM3，对应:6021
设备的Modbus TCP端口被映射到COM4，对应:502
6.通过Socket控制EIO
运行光盘内的eiodemo_socket-> 。
此目录下有测试程序的Delphi源码。
1)点击连接
2)测试输出，点击输出1-8，相应的继电器应该吸合。
3)测试入，点击输<重新读取开关量输入状态>，如果响应输入通道为1，将在
输入1-8上打勾。
7.温湿度数据采集
安装ESEN采集软件，此软件支持1-500点温湿度数据采集及现场报警。
新建一个采集点即可看到温湿度数据。
编程协议见《EIO技术配置手册》。
8.管理EIO
可以使用VSPM的<Telnet管理>功能或超级终端的TCP/IP功能登录到设备进行管理。
EIO默认的管理员口令：admin
9.恢复出厂值
通常不需要此操作，因为设备支持设备探测功能，所以即使遗失了IP地址，也可以通过虚拟串口的<设备探测器>找到设备，并且可以通过软件管理功能来恢复出厂设置。
按住恢复出厂值按钮，重新启动或上电，等待10秒左右，直到<Work>指示灯开始闪烁，就可以恢复到下列默认设置：
IP地址：IP认证：禁用
EIO设备性能指标。