翻转式杠杆臂钻夹具说明书
杠杆零件的机械加工工艺规程和夹具设计_毕业设计说明书

杠杆零件的机械加工工艺规程和夹具设计摘要本设计是CA6140车床杠杆零件的加工工艺规程及一些工序的专用夹具设计。
CA6140车床杠杆零件的主要加工表面是平面和孔。
一般来说,保证平面的加工精度要比保证孔的加工精度容易。
因此,本设计遵循先面后孔的原则,并将孔与平面的加工明确划分成粗加工和精加工阶段以保证孔和平面的加工精度。
基准的选择以杠杆错误!未找到引用源。
45外圆面作为粗基准,以错误!未找到引用源。
25孔及其下表面作为精基准。
先将底面加工出来,然后作为定位基准,在以底面作为精基准加工孔。
整个加工过程选用专用夹具,考虑到零件的结构尺寸简单,加紧方式多采用手动加紧,加紧简单,机构设计简单,且能满足设计要求。
关键词:杠杆零件,加工工艺,夹具,定位,加紧图A:零件三维效果图AbstractThis paper is to design the craft processes of making the CA6140lever spare parts and some specialized tongs in the process. The CA6140 lever spare part primarily processes the surface and bores. Generally speaking, to guarantee the accuracy of the flat surface process is easier than that of the bore. Therefore, this design follows the principle that surface first and then the bore, and definitely divides the process of flat surface and bore into coarse processes and precise processes to guarantee the bore process. The basic choice is to consider 45 outside circle as rough basis and to consider 25bore and its next surface as precise basis . The bottom is first processed out to be fixed position basis, and process the bore using the bottom as the precise basis. In the whole processes , specialized tongs are used. In consideration ofthe simple construction size of the spare parts, clipping by hands is adopted. It is simple, and the organization is simple, and can satisfy the design request.Key Words : Lever spare parts, craft process, tongs, fixed position, tight clip目录摘要 (I)ABSTRACT .................................................................................................. I I 目录 .. (Ⅲ)第一章绪论 (1)1.1课题背景及发展趋势 (1)1.2夹具的基本结构及夹具设计的内容 (1)第二章杠杆加工工艺规程设计 (3)2.1零件的作用 (3)2.2零件的工艺分析 (3)2.3工艺规程的设计 (4)2.4机械加工余量、工序尺寸及毛坯尺寸、工时的确定 (7)第三章专用夹具设计 (26)3.1加工Ø25孔夹具设计 (26)3.2粗、精铣宽度为30MM的下平台夹具设计 (30)总结 (36)参考文献 (37)致谢 (39)附件一 (40)附件二 (58)第一章绪论加工工艺及夹具毕业设计是对所学专业知识的一次巩固,是在进行社会实践之前对所学各课程的一次深入的综合性的总复习,也是理论联系实际的训练。
CA6140杠杆设计说明书

目录1 绪论 (2)2 杠杆加工工艺规程设计 (2)2.1 零件的分析 (2)2.1.1 零件的作用 (2)2.1.2 零件的工艺分析 (2)2.1.3杠杆的技术要求 (3)2.2杠杆加工的主要问题和工艺过程设计所应采取的相应措施 (3)2.2.1 确定毛坯的制造形式 (3)2.2.2基面的选择 (3)2.2.3 制定工艺路线 (4)2.2.4机械加工余量、工序尺寸及毛坯尺寸的确定 (6)2.2.5确定切削用量 (7)2.2.6确定加工工时 (7)3夹具设计 (8)3.1粗精铣宽度为30mm的下平台夹具设计 (8)3.1.1定位基准的选择 (8)3.1.2定位元件的设计 (8)3.1.3定位误差分析: (9)3.1.4夹具体槽形与对刀装置设计 (9)3.1.5夹紧装置及夹具体的设计 (12)3.1.6夹紧力计算 (12)3.1.7夹具设计及操作的简要说明 (13)参考文献 (13)1 绪论加工工艺及夹具毕业设计是对所学专业知识的一次巩固,是在进行社会实践之前对所学各课程的一次深入的综合性的总复习,也是理论联系实际的训练。
机床夹具已成为机械加工中的重要装备。
机床夹具的设计和使用是促进生产发展的重要工艺措施之一。
随着我国机械工业生产的不断发展,机床夹具的改进和创造已成为广大机械工人和技术人员在技术革新中的一项重要任务2 杠杆加工工艺规程设计2.1 零件的分析 2.1.1 零件的作用题目所给定的零件是CA6140车床的杠杆。
它位于车床制动机构中,主要起制动作用。
杠杆一端与制动带连接,另一端通过刚球与齿条轴的凸起(或凹槽)相接触,当离合器脱开时,齿条轴与杠杆下端接触,是起逆时针方向摆动,将制动带拉紧;当左右离合器中任一个接合时,杠杆都顺时针方向摆动,使制动带放松,从而达到制动的目的。
2.1.2 零件的工艺分析1、主要加工面:(1)、钻Φ0.023025+孔以及与此孔相通的Φ14阶梯孔、M8螺纹孔; (2)、钻Φ0.1012.7+锥孔及铣Φ0.1012.7+锥孔表面;(3)、钻2—M6螺纹孔及其上表面; (4)、铣杠杆底面。
杠杆臂零件钻夹具及工艺规程论文初

本科毕业论文机床杠杆臂钻夹具及机械加工工艺规程设计院部:机电工程系专业:机械设计及其自动化姓名:指导教师:二〇一三年四月毕业论文诚信声明本人郑重声明:所呈交的毕业论文《机床杠杆臂钻夹具及机械加工工艺规程设计》是本人在指导老师的指导下,独立研究、写作的成果。
论文中所引用是他人的无论以何种方式发布的文字、研究成果,均在论文中以明确方式标明。
本声明的法律结果由本人独自承担。
毕业论文作者签名:陈伟2013 年 4 月 8 日摘要本文主要介绍杠杆臂、机械加工工艺规程设计、翻转式钻床夹具以及金属切削机床等方面的知识。
杠杆臂加工工艺规程及其钻孔的夹具设计是包括零件加工的工艺设计、工序设计以及专用夹具的设计三部分。
在工艺设计中要首先对零件进行分析,了解零件的工艺再设计出毛坯的结构,并选择好零件的加工基准,设计出零件的工艺机床设计的重点是选定零件翻转式钻床夹具在工艺设计中要首先对零件进行分析,了解零件的工艺再设计出毛坯的结构,并选择好零件的加工基准,设计出零件的工艺路线;然后对零件各个工步的工序进行尺寸计算,确定各个工序的工艺装备及切削用量,然后进行专用夹具的设计,选择设计出夹具的各个组成部件,如定位元件、夹紧元件、引导元件、夹具体与机床的连接部件以及其它部件;计算出夹具定位时产生的定位误差,分析夹具结构的合理性与不足之处,并在以后设计中注意改进。
【关键字】杠杆臂,工艺,钻夹具,切削用量,夹紧,定位AbstractThis paper mainly introduces the technical regulations of the lever arm, mechanical design, tilting drilling fixture and metal cutting machine tools and other aspects of knowledge.Focus on the design of machine tool is selected parts of tilting drilling fixture in the process design should first of all parts for analysis, to understand the parts of the process to design blank structure, and choose the good parts machining datum, design a part of the process route; and then the parts of each step of process dimension calculation, is the key to decide process equipment and cutting of various process amount, then design special fixture fixture design, selection of the various components, such as the connecting part positioning element, clamping elements, guiding elements, fixture and machine tools and other components; calculate fixture when generatingThe positioning error analysis, rationality and shortcoming of the fixture structure, pay attention to improve and design in later.Keywords:lever arm, process,fixture, cutting dosage, clamping,positioning目录第一章前言 (1)第二章零件分析 (2)2.1 零件作用 (2)2.2零件的工艺分析 (2)第三章工艺规程设计 (4)3.1确定毛坯的制造形式 (4)3.2基面的选择 (4)3.3制定工艺路线 (4)3.4机械加工余量、工序尺寸及毛坯尺寸的确定 (5)3.5确定切削用量 (5)3.6确定基本工时 (12)第四章夹具设计 (16)4.1 夹具的工作原理与结构设计 (16)4.2 夹具的使用方法 (17)4.3 夹具与翻转式钻床的固定 (17)4.4 定位误差分析 (17)4.5 铣削力与夹紧力计算 (18)第五章翻转式钻床夹具零件的具体设计 (19)5.1钻床夹具的概括 (19)5.2 夹具零件的设计 (20)5.3 夹具体的设计 (20)5.4定位销的设计 (21)5.5 钻模板以及钻套的设计 (21)第六章总结 (27)参考文献 (28)致谢 (29)第一章前言机械加工工艺是规定产品或零件机械加工工艺过程和操作方法,是指导生产的重要的技术性文件。
杠杆夹具说明书

目录前言 (1)一、零件分析 (1)1.1 零件的作用 (1)1.2 零件的工艺分析 (1)二、确定毛坯、画毛坯----零件合图 (2)2.1 选择毛坯 (2)2.2 确定毛坯的尺寸公差和机械加工余量 (2)三、工艺规程的设计 (4)3.1 确定毛坯的制造形式 (4)3.2工件表面加工方法的选择 (5)3.3确定工艺路线 (5)3.4工艺方案的比较和分析 (7)3.5选择加工设备及刀、量、夹具 (7)3.6加工工序设计 (8)四、夹具的设计 (12)4.1 确定设计方案 (12)4.2 选择定位元件 (12)4.3 计算夹紧力并确定螺杆直径 (12)4.4 定位误差计算 (13)设计心得 (14)参考文献 (14)前言机械制造技术基础课程设计是在学完了机械制造技术基础和大部分专业课,并进行了生产实习的基础上进行的一个教学环节。
这次设计使我们能综合运用机械制造工艺学中的基本理论,并结合生产实习中学到的实践知识,独立地分析和解决工艺问题,初步具备了设计一个中等复杂程度零件(杠杆零件)的工艺规程的能力和运用夹具设计的基本原理和方法,拟定夹具设计方案,完成夹具结构设计的能力,也是熟悉和运用有关手册﹑图表等技术资料及编写技术文件等基本技能的一次实践机会,为今后的毕业设计及未来从事的工作打下良好的基础。
由于能力所限,经验不足,设计中还有许多不足之处,望程老师指教。
一、零件分析1.1 零件的作用杠杆是铣床进给机构中起支撑固定作用的零件Φ25孔与轴连接起支撑本零件的作用,左右两孔Φ8H7各装一拨叉,控制铣床工作台自动进给的离合器。
Φ10孔通过销与另一杠杆连接,操纵手柄即可实现铣床工作台三个方向的自动进给。
1.2 零件的工艺分析其材料为HT200。
该材料有较高的强度、耐磨性、耐热性适应用于较大应力。
杠杆的Φ25+0.052mm孔的轴线合两个端面有着垂直度的要求。
现分述如下:本夹具用于在立式钻床上,加工Φ8(H7)孔。
(建议下载)“杠杆”零件的机械加工工艺规程及专用夹具设计说明书

五、设计心得 (26)六、参考文献 (27)一、零件分析(一)零件的作用题目给出的零件是杠杆。
它的主要的作用是用来支承、固定的。
要求零件的配合是符合要求。
(二)零件的工艺分析杠杆的Φ25+0.052mm孔的轴线合两个端面有着垂直度的要求。
现分述如下:本夹具用于在立式钻床上,加工Φ8(H7)孔。
工件以Φ25+0.052mm 孔及端面和水平面底、Φ30的凸台分别在台阶定位销7、支承钉11上实现完全定位。
钻Φ8(H7)mm孔时工件为悬臂,为防止工件加工时变形,采用了螺旋辅助支承2,当辅助支承2与Φ10(H7)孔、钻2×Ф8+0.015的小孔、粗精铣Φ30凸台的平台。
材料为HT200,加工方法选择如下:1、Φ40mm圆柱的上平台:公差等级为IT7,表面粗糙度为Ra6.3,采用粗铣→精铣的加工方法,并倒R3圆角。
2、Φ40mm圆柱的下平台:公差等级为IT7,表面粗糙度为Ra3.2,采用采用粗铣→精铣的加工方法,并倒R3圆角。
3、Φ30mm的凸台上下表面:公差等级为IT7,表面粗糙度为Ra6.3,采用粗铣→精铣的加工方法。
4、钻Φ10(H7)内孔:公差等级为IT7,表面粗糙度为Ra3.2,平行度为0.1µm(A),采用钻孔→粗铰→精铰的加工方法。
5、钻Φ25(H9)内孔:公差等级为IT9,表面粗糙度为Ra1.6,采用钻孔→扩孔钻钻孔→精铰的加工方法,并倒1×45°内角。
6、钻Φ8(H7)内孔:公差等级为IT7,表面粗糙度为Ra1.6,采用钻孔→粗铰→精铰的加工方法。
(四)、确定工艺路线1、工艺路线方案一:铸造时效涂底漆工序Ⅰ:粗精铣宽度为Ф40mm的上下平台和宽度为30mm的平台工序Ⅱ:粗精铣宽度为Φ30mm的凸台表面工序Ⅲ:钻孔Ф25(H9)使尺寸达到Ф23mm。
工序Ⅳ:扩孔钻钻孔Ф25(H9)使尺寸达到Ф24.8mm。
工序Ⅴ:铰孔Ф25(H9)使尺寸达到Ф25(H9)。
杠杆零件的机械加工工艺规程与夹具设计说明书

专业课程设计说明书设计题目“杠杆”零件的机械加工工艺规程与夹具设计设计者指导教师XX大学机电与建筑工程学院(2**年9月16日)专业课程设计任务书题目: “杠杆”零件的机械加工工艺规程与夹具设计原始图纸(见附页)生产类型:中批量设计内容:1、零件图 1张2、毛坯图 1张3、机械加工工艺过程卡 1份4、机械加工工序卡 1份5、夹具装配图 1套6、夹具零件图若干7、课程设计说明书 1份班级姓名学号指导教师目录前言一、零件的分析(一)零件的作用(二)零件的工艺分析二、工艺规程的设计(一)确定毛坯的制造形式(二)基准的选择(三)工艺路线的拟定及工艺方案的分析(四)机械加工余量、工序尺寸及毛坯尺寸的确定三、专用夹具的设计(一)确定夹具类型(二)拟定定位方案选择定位元件(三)导引装置设计(四)夹紧机构设计(五)夹具操作动作说明四、总结五、主要参考文献设计说明前言:本次设计对我来说是相当重要的,它不仅考察我们对机械行业专业知识的掌握情况,更是要我们从实际出发,结合所学的知识,设计出最优化的夹具来。
这次设计让我熟悉了夹具设计的整个流程,并了解了在设计过程中需考虑哪些因素,它锻炼了我分析问题,解决问题的能力。
这次设计对我来说是有帮助的,也是十分必要的。
一 零件的分析(一) 零件的作用该零件的主要作用是在机构运动中起到支承作用(二) 零件的工艺分析 1. 零件加工要求分析(1) Φ28H7孔及两端面。
(2) Φ10H9两端面。
(3) 钻、扩、铰Φ10H9孔及Φ11孔。
要求:Φ10H9孔与Φ28H7孔的距离为(80+0.2)mm ;平行度为0.3mm 。
Φ11孔与Φ28H7孔的距离为(15+0.25)mm 。
Φ11孔与端面K 的距离为14mm 。
(4) 槽。
要求:槽宽0.509.5+ mm ,中心对称分布,单边尺寸为0.204.75+ mm 。
2. 设立夹具根据零件分析,为保证精度要求,设立(3)的钻模夹具: 使用夹具前已加工表面为: (1) Φ28H7孔及两端面。
钻摇臂小头孔的夹具设计说明书

钻摇臂小头孔的夹具设计设计说明书姓名:曲晓龙班级:0820132 学号:11目录夹具设计任务 (1)1、精度与批量分析 (3)2、确定夹具的结构方案 (3)⑴确定定位方案,选择定位元件⑵确定导向装置⑶确定夹紧机构⑷确定其他装置和夹具体3、夹具装配图上的的主要标注尺寸、配合及技术要求 (4)4、夹具装配图 (5)5、总结和体会 (5)夹具设计任务:如下图为钻摇臂小头孔的工序简图。
已知:工件材料为45钢,毛坯为模锻件,所用机床为Z525型立式钻床,成批生产规模。
试为该工序设计一钻床夹具。
说明:本工序是为一钻摇臂小头孔所设计的一套钻床夹具。
主要技术指标能保证工件的加工精度、提高生产效率、工艺性好和使用性好。
我们在设计专用夹具时为了能满足工件的加工精度要求,考虑了合理的定位方案、合适的尺寸、公差和技术要求,并进行了必要的精度分析。
由于是中批量生产,采用了立式钻床夹具,提高了生产效率。
在工艺性方面使这种夹具的结构简单、合理、便于加工、装配、检验和维修。
在使用性方面这种夹具的操作简便、省力、安全可靠,排屑也方便,必要时可设置排屑结构。
通过对钻床夹具设计的制作,进一步巩固和所学基本知识并使所学知识得到综合运用。
学会查阅和收集技术资料,提高运用计算机辅助设计的能力,树立正确的设计思想和严谨的工作作风,提高实践能力。
1、精度与批量分析本工序有一定位置精度要求,属于批量生产,使用夹具加工是适当的。
考虑到生产批量不是很大,因此夹具结构应尽可能简单,以降低成本。
4、夹具装配图 :见附表5、总结和体会这次设计性实习让我受益匪浅。
让我感触最深的是要想设计出一个好的机械那得需要很多方面的知识(像CAD制图,机械制造基础,机械加工技术,机械原理,互换性与测量技术,零件铸造成型,工程材料学等等),只知其中一些是远远不够的。
因此本以为学的还不错的我受到了不小的震撼——原来自己还有那么多的知识要学。
值得庆幸的是在这次实习中我总结了一些机械设计方法:搞机械设计首先要了解自己所要设计的机械的用途,然后根据其用途选用合适的材料。
杠杆零件加工工艺,设计Φ10孔的钻床夹具

机械制造技术课程设计说明书设计题目:制定杠杆零件加工工艺,设计Φ10孔的钻床夹具专业:机械电子工程班级: 12-3 学号: 1230120329 姓名:周爱国指导教师:张中然机械工程系2015年11月21日目录序言 ...................................................................................................................... - 1 -一零件的分析 ................................................................................................ - 2 -1.1零件的作用............................................................................................... - 2 -1.2零件的工艺分析....................................................................................... - 2 -二工艺规程的设计......................................................................................... - 3 -2.1确定毛坯的制造形式............................................................................... - 3 -2.2基面的选择............................................................................................... - 3 -2.3.工件表面加工方法的选择及制定工艺路线........................................... - 5 -2.4 机械加工余量、工序尺寸及毛坯尺寸的确定...................................... - 6 -2.5 确定切削用量及基本工时...................................................................... - 8 -三夹具设计..................................................................................................... - 14 -3.1问题的提出............................................................................................. - 14 -3.2设计方法和步骤..................................................................................... - 14 -3.3夹紧装置的设计..................................................................................... - 18 -3.4导向装置的设计及其他装置结构......................................................... - 21 -3.5确定夹具技术要求和有关尺寸,公差配合......................................... - 22 -3.6夹具精度分析与计算............................................................................. - 23 -总结 .................................................................................................................... - 24 -参考文献........................................................................................................... - 25 -序言机械制造业是制造具有一定形状位置和尺寸的零件和产品,并把它们装备成机械装备的行业。
翻转式杠杆臂钻夹具说明书

摘要根据设计要求首先确定了杠杆臂的基本设计思路,通过对该零件作用分析,形位公差分析、加工工艺、工序设计完成零件的工艺制造思路。
而后确定了定位基准的选择,和夹紧方式的确定,最后经过反复比对后使用三维造型软件进行了初步的草图绘制,确定夹具的外形尺寸,然后设计钻模板和钻套等,为了简化设计减少非标零件的设计和制造成本,选用了较多的螺钉螺母等非标零件。
本次夹具设计过程中夹具采用进行紧凑的设计方案,这样较为节省材料和成本,但是夹具的安装定位显得比较细致,空间利用率较高。
为了方便的放入和取出工件而不对周边产生操作影响和降低生产效率,采用了钻模板的翻转设计模式,左侧的钻模板在非工作时可以方便的拉起,让工件可以顺利放入,安装完毕后翻下钻模板。
【关键字】杠杆臂,工艺,钻夹具,夹紧,定位目录第一章绪论 (3)1.1机床夹具介绍 (3)1.2现代夹具的发展发向 (3)1.3设计目标与任务 (4)1.4 主要研究方向与方法 (4)第二章零件分析 (6)2.1零件的作用 (6)2.2 零件的工艺分析 (6)第三章夹具设计 (8)3.1.夹具的工作原理与结构设计 (8)3.2 夹具的使用方法 (10)3.3 夹具与翻转式钻床的固定 (10)3.5夹紧力计算 (11)第四章:翻转式钻床夹具零件的具体设计 (12)4.1钻床夹具的概括 (12)4.2 夹具零件的设计 (13)4.3夹具体的设计 (14)4.4定位销的设计 (14)4.5 钻模板以及钻套的设计 (14)第五章总结 (21)致谢 (22)参考文献 (23)第一章绪论1.1机床夹具介绍夹具从1787年至今经过了在工业发展初期。
夹具仅作为加工工艺过程中的辅助工具;到后期机床、汽车、飞机等制造业大力发展后,成为主要工艺装备;直到目前近代由于世界科学技术的进步及社会生产力的迅速提高,夹具与机床的紧密结合的一路发展历程看来,夹具在工业生产中的重要地位。
现代生产要求企业制造激烈竞争夹具的应用五花八门,近年来年柔性制造系统(FMS)、数控机床(NC),加工中心(MC)和成组加工(GT)的应用使大批量生产的水平大幅提升。
杠杆钻20孔夹具设计说明书

夹具设计(一)机床夹具在机械加工中的作用在机械技工过程中,工件的几何精度主要取决于工件对机床的相对位置,严格地说,只有机床、刀具、夹具和工件之间保持正确的相对关系,才能保证工件各加工表面之间的相对位置精度。
显然,对机床夹具的基本要求就是将工件正确定位并牢靠地固定在给定位置。
因而,机床夹具除了应保证足够的制造精度外,还应有足够的刚度,以抵抗加工时可能产生的变形和振动。
机床夹具在机械加工中起着十分重要的作用,归纳起来,主要表现在以下几个方面:①缩短辅助时间,提高劳动生产率,降低加工成本。
使用夹具包括两个过程,一是夹具在机床上的安装和调整,二是工件在夹具中的安装。
前者可以依靠夹具上的定位键、对刀块等专门装置快速实现,后者则由夹具上专门用于定位的V 形块、定位环等元件迅速实现。
此外,夹具中还可以不同程度地采用高效率的多件、多位、快速、增力、机动等夹紧装置,利用辅助支撑等提高工件的刚度,以利于采用较大的切削用量。
这样,便可缩短辅助时间、减少机动时间,有效地提高劳动效率、降低加工成本。
②保证加工精度,稳定加工质量。
采用夹具安装工件,夹具在机床上的安装位置和工件在夹具中的安装位置均已确定,因而工件在加工过程中的位置精度不会受到各种主观因素以及操作者的技术水平的影响,加工精度易于得到保证,并且加工质量稳定。
③降低对工人的技术水平要求,减轻工人的劳动强度,保证安全生产。
使用专用夹具安装工件,定位方便、准确、快捷,位置精度易于得到保证,因而可以降低对工人的技术要求;同时夹紧又可采用增力、机动等装置,可以减轻工人的劳动强度。
根据加工条件,还可以设计防护装置,确保操作者的人身安全。
④扩大机床的工艺范围,实现“一机多能”。
在批量不大、工件种类和规格多、机床品种有限的生产条件下,可以通过设计机床夹具、改变机床的工艺范围,实现“一机多能”。
例如:在普通铣床上安装专用夹具铣削成形表面;在车床溜板上或在摇臂钻床上安装镗模可以加工箱体孔系等。
北方工业工具5速杠杆钻机说明书

BENCH DRILL PRESSOWNER'S MANUALItem # WARNING:Read carefully and understand all INSTRUCTIONS beforeoperating. Failure to follow the safety rules and other basicsafety precautions may result in serious personal injury.45266Thank you very much for choosing a Northern Industrial Tools Product!For future reference, please complete the owner's record below:Model: _______________ Purchase Date: _______________Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.This machine is designed for certain applications only. The distributor cannot be responsible for issues arising from modification. We strongly recommend this machine is not modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted the distributor to determine if it can or should be performed on the product.For technical questions please call 1-800-222-5381.INTENDED USEThis bench drill press is designed for drilling in metal or wooden pieces.TECHNICAL SPECIFICATIONSDescription SpecificationsMotor:1/2 HPVolts:120VSpeed:570 - 3050 RPMChuck Size:1/2”Swing:10"Stroke:21/3"Drilling Capacity:1/2”Work tabel:715/16" x 73/4"Work base:1311/16" x 81/4"Ship Weight:71 lbsGENERAL SAFETY RULESin electric shock, fire and/or serious injury.that common sense and caution are factors which cannot be built into this product, but must besupplied by the operator.SAVE THESE INSTRUCTIONSWORK AREA• Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents.• Do not use your tool where there is a risk of causing a fire or an explosion; e.g. in the presence of flammable liquids, gasses, or dust. Power tools create sparks, which may ignite the dust or fumes.• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control, so visitors should remain at a safe distance from the work area.12• Be aware of all power lines, electrical circuits, water pipes and other mechanical hazards in your work area, particularly those hazards below the work surface hidden from the operator's view that may beunintentionally contacted and may cause personal harm or property damage.• Be alert of your surroundings. Using power tools in confined work areas may put you dangerously close to cutting tools and rotating parts.ELECTRICAL SAFETYWARNING!Always check to ensure the power supply corresponds to the voltage on the rating plate.• Do not abuse the cord. Never yank tool or extension cords from the receptacle. Keep power and extension cords away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.Damaged cords may cause a fire and increase the risk of electric shock.• Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. • Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still doesn't fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.• Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increase risk of electric shock if your body is grounded.• When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W.” These cords are rated for outdoor use and reduce the risk of electric shock.• Extension Cord Use:A. Use only 'Listed' extension cords. If used outdoors, they must be marked “For Outdoor Use.” Thosecords having 3-prong grounding type plugs and mating receptacles are to be used with grounded tools.B. Replace damaged or worn cords immediately.C. Check the name plate rating of your tool. Use of improper size or gauge of extension cord may causeunsafe or inefficient operation of your tool. Be sure your extension cord is rated to allow sufficient current flow to the motor. For the proper wire gauge for your tool, see chart.•Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.• Do not let your fingers touch the terminals of plug when installing to or removing from the outlet.• Ground fault circuit interrupters. If work area is not equipped with a permanently installed Ground Fault Circuit Interrupter outlet (GFCI), use a plug-in GFCI between power tool or extension cord and power receptacle.PERSONAL SAFETY• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.• Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided.• Use safety apparel and equipment. Use safety goggles or safety glasses with side shields which comply with current national standards, or when needed, a face shield. Use as dust mask in dusty work conditions.This applies to all persons in the work area. Also use non-skid safety shoes, hardhat, gloves, dust collection systems, and hearing protection when appropriate.• Avoid accidental starting. Do not carry the power tool with your finger on the switch. Ensure the switch is in the off position before plugging tool into power outlet. In the event of a power failure, while a tool is being used, turn the switch off to prevent surprise starting when power is restored.• Do not overreach. Keep proper footing and balance at all times.• Remove adjusting keys or wrenches before connecting to the power supply or turning on the tool. A wrench or key that is left attached to a rotating part of the tool may result in personal injury.• Never place your fingers in a position where they could contact the drill or other cutting tool if the workpiece should unexpectedly shift or your hand should slip.• Whenever possible, position the WORKPIECE to contact the left side of the column if it is too short or the table is tilted, clamp solidly to the table. Use table slots or clamping ledge around the outside edge of the table.• When using a drill press VISE, always fasten it to a table.• Never climb on or allow others to climb on the drill press table; it could break or pull the entire drill press down.• Turn the motor Switch OFF and put away the Switch Key when leaving the drill press.• To avoid injury from thrown work or tool contact, do NOT perform layout, assembly, or setup work on the table while the cutting tool is rotating.TOOL USE AND CARE• Do not force the tool. Tools do a better and safer job when used in the manner for which they are designed.Plan your work, and use the correct tool for the job.• Never use a tool with a malfunctioning switch. Any power tool that cannot be controlled with the switch is dangerous and must be repaired by an authorized service representative before using.• Disconnect power from tool and place the switch in the locked or off position before servicing, adjusting, installing accessories or attachments, or storing. Such preventive safety measures reduce the risk of starting the power tool accidentally.• Secure work with clamps or a vise instead of your hand to hold work when practical. This safety precaution allows for proper tool operation using both hands.• Store idle tools. When tools are not is use, store them in a dry, secure place out of the reach of children.Inspect tools for good working condition prior to storage and before re-use.• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool.• Keep guards in place and in working order.For your own safety, do not try to use your drill press or plug it in until it is completely assembled and installed according to the instructions, read and understood this Instruction manual:•Your drill press must be bolted securely to a workbench. In addition, if there is any tendency for your drill press to move during certain operations, bolt the workbench to the floor•This drill press is intended for use in dry conditions, indoor use only.•Always keep hands out of the path of a drill bit. Avoid awkward hand positions where a sudden slip could cause your hand to move into the drill bit.•Do not install or use any drill bit that exceeds 175 mm (7") in length or extends 150 mm (6") below the chuck jaws. They can suddenly bend outward or break.•Do not use wire wheels, router bits, shaper cutters, circle (fly) cutters, or rotary planers on this drill press. •When cutting a large piece of material make sure it is fully supported at the table height.•Do not perform any operation freehand. Always hold the workpiece firmIy against the table so it will not rock or twist. Use clamps or a vise for unstable workpieces.•Make sure there are no nails or foreign objects in the part of the workpiece to be drilled.•Do not touch the bit or chips. Drill bits and cuttings are hot immediately offer drilling.•Never reach around or under the working head, or grab the chuck key to stop the drill press.•Make sure the drill press speed is appropriate for both the type of material and bit size you are using.34• Clamp workpiece or brace against the left side of the column to prevent rotation. If it is too short or the table is tilted, clamp solidIy to the table and use the fence provided. • If the workpiece overhangs the table such that it will fall or tip if not held, clamp it to the table. Provide auxiliary support. • Make sure all clamps and locks are firmly tightened before drilling. • Securely lock the head and table support to the column, and the table to the table support before operating the drill press. • Never turn your drill press on before clearing the table of all objects. (tools, scraps of wood, etc.) • Before starting the operation, jog the motor switch to make sure the drill bit does not wobble or vibrate. • Let the spindle reach full speed before starting to drill. If your drill press makes an unfamiliar noise or if it vibrates excessively, stop immediately, turn the drill press off and unplug. Do not restart until the problem is corrected. • Do not perform layout assembly or set up work on the table while the drill press is in operation. • Make sure the spindle has come to a complete stop before touching the workpiece. • To avoid injury from accidental starting, always turn the switch "OFF" and unplug the drill press before installing or removing any accessory or attachment or making any adjustment. • Keep guards in place and in working order. • Use onIy self-ejecting type chuck key as provided with the drill press. • Do not try to drill material too small to be securely held.• Use the drill press in a well-lit area and on a level surface clean and smooth enough to reduce the risk of trips, slips, or falls. Use it where neither the operator nor a casual observer is forced to stand in line with a potential kickback.For your own safety, do not attemp to operate your drill press until it is completely assembled 1. General Safety Instructions for Power Tools 2. Getting to Know Your Drill Press 3. Basic Drill Press Operation 4. Adjustments 5. MaintenanceUNPACKINGOn receipt, carefully unpack the components ensuring that no damage was suffered in transit, and that all following parts are accounted for.A. Table Support AsmB. Column Support AsmC. ManualD. Box of Loose PartsE. BaseF. Head AsmG. Bag of Loose Parts5Check the parts againts the abovelist and refer to the diagrams.Should there be any deficiencies ordamage, you should contactthe distributor.GETTING TO KNOW YOUR DRILL PRESSASSEMBLY1.Position base on workbench.2.Remove protective sleeve from column tube and discard. Placecolumn assembly on base, and align holes in column support withholes in base.3.Locate four (4) 5/16” Dia. x 3/4” long bolts among loose parts bag.4.Install a bolt in each hole through column support and base andtighten with adjustable wrench.5.Loosen set screw in cloumn collar with 3mm HEX “L” wrench andremove collar and rack from column.1. Belt Tension Lock Handles2. Feed Handle3. Table Crank4. Chuck Key5. Chuck6. Depth Scale7. Drill “ON-OFF” Switch8. Depth Scale Lock9. Spring Cap10. Head Locks11. Bevel Scale12. Support Lock Handle13. Table Bevel Lock66.Find elevation worm gear shaft in the loose parts bag. Insert the elevation shaft into the table support and extend the shaft through the opening as far as possible. The crank is to be installed on the elevation worm gear shaft, the set screw is to be aligned with the flat portion of the shaft. The crank is to be positioned as close to the arm support as possible, then tighten set screw. (see illustration)7.With long smooth end of rack pointing upward, slide rack down through large round opening in table support. Engage rack in gear mechanism found inside opening of table support.8.While holding rack and table support in an engaged position slide both down over column. Slide rack down column until rack is positioned against lower column support.9.Replace column collar and position it bevel side down over rack. Tighten set screw in collar with 7/64” HEX “L” wrench. To let the rack slide when the table is swing to the left or right around the column, the collar must sit loosely over rack and should not be angled on the column. Only tighten set screw enough to keep collar in place, otherwise the collar may break due to excess pressure.10.Check column collar for proper adjustment. Collar should not be angled on the column and it should be positioned so rack will slide freely in collars when table is rotated 360º around column tube. If re-adjusted, only tighten set screw enough to keep collar in place.Note:To avoid column or collar damage, do not over-tighten set screw.11.Locate support lock handle in loose parts bag and tighten by hand.12.To minimize crank backlash; tighten the support lock and rotate elevation worm shaft clockwise with the crank. Loosen the set screw in the crank and reposition the crank as close to the table support as possible. Tighten the set screw in the crank.ing a 4mm HEX “L” wrench tighten the head lock set screws on the rightside of the head.OPERATIONDrill “ON-OFF” switchThis feature is intended to help prevent unauthorized and possible hazardous use by children and others.Insert KEY into switch.Note: Key is made of yellow plastic.To turn drill ON:Insert finger under switch lever and pull.To turn drill OFF:Push lever in.In an emergency: If the drill bit BINDS... STALLS...STOPS... or tends to tear the workpiece loose... you can quickly turn the drill OFF by hitting the switch with the palm of your hand.WARNING! For your own safety, always push the switch “OFF” when drill press is not in use; Remove key and keep it in a safe place. In the event of a power fallure (all of your lights go out) or blown fuse or tripped circult breaker, turn switch off, lock it and remove the key. This will prevent the drill press from starting up again when the power comes back on.MAINTENANCEWARNING! For your own safety, turn switch “off” and remove plug from power source outlet beforemaintaining or lubricating your drill press.WARNING! To avoid shock or fire hazard, if the power cord is worn or cut, or damaged in any way, have it replaced.WARNING! Make sure this tool is disconnected from its power source before attempting any maintenance, cleaning, or inspection.• Maintain your tools.It is recommended that the general condition of any tool be examined before it is used.Keep your tools in good repair by adopting a program of conscientious repair and maintenance in accordance with the recommended procedures found in this manual. If any abnormal vibrations or noise occurs, turn the tool off immediately and have the problem corrected before further use. Have necessary repairs made by qualified service personnel.• Keep cutting tools sharp and clean.Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Keep handles dry, clean, and free from oil and grease.• e only soap and a damp cloth to clean your tools. Many household cleaners are harmful to plastics and other insulation. Never let liquid get inside a tool.78WARRANTYOne-Year Limited WarrantyFor warranty questions, call 1-800-222-5381DIAGRAM & PARTS LIST9Distributed byNorthern Tool + Equipment Co., Inc.Burnsville, MN 55306Made in China。
制动杠杆夹具说明书

制动杠杆夹具设计前言这次课程设计是夹具设计的最后一个总结性的设计,是对夹具本书的一次全面形的检查和巩固,这次的课程设计是应用所学的基础理论,专业知识去解决实际问题的一次综合训练。
通过本次的设计,使我巩固了已学的知识加深了印象。
夹具设计本身受到各个方面的限制,在一定的限制中要求有合理的设计思想,最合理的设计结果,达到人们所渴望的要求,满足生产的需要。
设计要有创新还要有易于实现,因此设计要从实际出发围绕着实际的问题而进行。
我们在所学知识的基础上进行设计,是尝试的设计,但是通过本次设计,我们熟练了设计的基本要领,更锻炼了我们面对自己没有面对过的问题时的处理态度和处理方法。
通过和大家的一起设计,我掌握了很多技巧和方法,确实对我是一次很好的锻炼。
人就在锻炼中成长。
由于本身所学知识有限,设计能力有限,在设计中难免有很多的错误和不足,恳请广大指导老师批评指正。
为了提高劳动生产率,保证加工质量,需要设计专用夹具。
经过与两位指导老师的协商,决定设计第七道工序——钻2-M6螺纹底孔,再攻螺纹,本夹具将用于Z535立式钻床,刀具为麻花钻头以及丝锥,对工件进行加工。
1零件的分析本夹具主要用于钻2-M6螺纹孔,由于加工的螺纹孔对于精度要求并不十分严格,又在本道工序中,Φ22的孔,以及A面已经加工完成。
因此,本道工序中主要考虑对于工件的定位加工,其次是考虑如何提高劳动生产率,保证加工质量,降低劳动强度。
1.1主要技术要求2夹具体的选择2.1定位基准的选择图1由零件图图1可知:根据工序设计此处已经完成了的Φ22的孔和已经加工完成了的A面的加工精度要求比较高,所以在此处选择Φ22的中心孔的中心线为定位基准,限制5个自由度,再利用一个圆柱挡销来限制工件1个自由度,以达到定位所需的要求,再配上一个支撑钉作为辅助支撑,以此来达到工件加工所需的要求。
图2首先作为定位基准,我们可以从图3看出,我们选择了Φ22的孔作为主要的定位基准,由此来限制住工件X、Y、Z三个方向上的平动的自由度以及Y、Z方向上的转动的自由度,由一根心轴与夹具体相连接,再用两个螺母夹紧。
移动翻转式专用夹具设计说明书

目录绪论 (2)1 夹具设计简介 (3)1.1 机床夹具的功能 (3)1.2 已知工件 (3)1.3机床夹具应满足的要求 (3)1.4设计已知条件 (3)2 夹具的结构设计 (4)2.1 设计机床夹具前的准备工作 (4)2.1.1 明确工件的生产要求 (4)2.1.2 充分理解工件的零件图和工序图 (4)2.2 确定机床夹具的结构方案 (5)2.2.1 选择定位原件 (5)2.2.2 选择夹紧机构 (6)2.2.3 机床夹具的总体形式 (6)2.3 绘制夹具装配图 (10)2.4 绘制夹具零件图 (11)3 夹具精度的验算 (14)3.1 定位误差的分析与计算 (14)3.1.1 定位误差 (14)3.1.2 产生定位误差的原因 (15)4 致谢与感想 (16)5.1 致谢 (16)5.2 感想 (17)5 参考文献 (18)前言机械制造技术基础是机械设计制造及其自动化(或机械工程及自动化)专业的一门重要的专业基础课。
机械设计是机械工程的重要组成部分,是决定机械性能的最主要因素。
由于各产业对机械的性能要求不同而有许多专业性的机械设计。
在机械制造厂的生产过程中,用来安装工件使之固定在正确位置上,完成其切削加工、检验、装配、焊接等工作,所使用的工艺装备统称为夹具。
如机床夹具、检验夹具、焊接夹具、装配夹具等。
机床夹具的作用可归纳为以下四个方面:1.保证加工精度机床夹具可准确确定工件、刀具和机床之间的相对位置,可以保证加工精度。
2.提高生产效率机床夹具可快速地将工件定位和夹紧,减少辅助时间。
3.减少劳动强度采用机械、气动、液动等夹紧机构,可以减轻工人的劳动强度。
4.扩大机床的工艺范围利用机床夹具,可使机床的加工范围扩大,例如在卧式车床刀架处安装镗孔夹具,可对箱体孔进行镗孔加工。
机械制造装备设计课程设计是机械设计中的一个重要的实践性教学环节,也是机械类专业学生较为全面的机械设计训练。
其目的在于:1.培养学生综合运用机械设计基础以及其他先修课程的理论知识和生产实际知识去分析和解决工程实际问题的能力,通过课设训练可以巩固、加深有关机械课设方面的理论知识。
铣床杠杆的说明书

目录一、零件分析................................... ... 二、规程设计..................................三、夹具设计..............................四、设计心得....................................... 五、参考文献.......................................序言机械制造工艺学课程设计是在学完了机械制造工艺学(含机床夹具设计)和大部分专业课,并进行了生产实习的基础上进行的一个教学环节。
这次设计使我们能综合运用机械制造工艺学中的基本理论,并结合生产实习中学到的实践知识,独立地分析和解决工艺问题,初步具备了设计一个中等复杂零件(杠杆)的工艺规程的能力和运用夹具设计的基本原理和方法,拟定夹具设计方案,由于能力有限,经验不足,设计中还有许多不足之处,希望各位老师多加以指教。
完成夹具结构设计能力,也是熟悉和运用有关手册、图表等技术资料及编写技术文件等基本技能的一次实践机会,为今后的毕业设计及未来从事的工作打下良好的基础。
杠杆的零件图一、(一)零件的作用题目给出的零件是杠杆。
它的主要的作用是用来支承、固定的。
要求零件的配合是符合要求。
(二)零件的工艺分析杠杆的Φ25+0.052mm孔的轴线合两个端面有着垂直度的要求。
现分述如下:本夹具用于在立式钻床上,加工Φ8(H7)孔。
工件以Φ25+0.052mm 孔及端面和水平面底、Φ30的凸台分别在台阶定位销7、支承钉11上实现完全定位。
钻Φ8(H7)mm孔时工件为悬臂,为防止工件加工时变形,采用了螺旋辅助支承2,当辅助支承2与工件接触后,用螺母1锁紧。
要加工的主要工序包括:粗精铣宽度为Φ40mm的上下平台、钻Φ10(H7)孔、钻2×Ф8+0.015的小孔、粗精铣Φ30凸台的上下表面。
加工要求有:Φ40mm的平台的表面粗糙度各为Ra6.3um (上平台)、Ra3.2(下平台)、Φ10(H7)孔为Ra3.6um、Φ25(H9)和Φ8(H7)孔表面粗糙度都为Ra1.6um。
CA6140车床杠杆的加工工艺及夹具设计【优秀钻25孔】

机械制造工艺学CA6140杠杆夹具设计说明书学生姓名:学生学号:院(系):年级专业:指导教师:二〇〇八年八月目录前言1定位基准的选择2切削力的计算与夹紧力分析3夹紧元件及动力装置确定4钻套、衬套、钻模板及夹具体设计5夹具精度分析6夹具设计及操作的简要说明7小结专用夹具设计为了提高劳动生产率,保证加工质量,降低劳动强度。
在加工杠杆零件时,需要设计专用夹具。
根据任务要求中的设计内容,需要设计加工工艺孔Φ25夹,加工工艺孔的夹具将用于组合钻床,刀具分别为麻花钻、扩孔钻、铰刀对工件上的工艺孔进行加工。
加工工艺孔Φ25夹具设计本夹具主要用来钻、扩、铰工艺孔Φ25。
这个工艺孔有尺寸精度要求为+0.023,表面粗糙度要求,表面粗糙度为 1.6a R m μ=,与顶面垂直。
并用于以后各面各孔加工中的定位。
其加工质量直接影响以后各工序的加工精度。
本到工序为杠杆加工的第二道工序,加工到本道工序时只完成了杠杆下表面的粗、精铣。
因此再本道工序加工时主要应考虑如何保证其尺寸精度要求和表面粗糙度要求,以及如何提高劳动生产率,降低劳动强度。
1定位基准的选择由零件图可知,工艺孔位于零件中心偏左,其有尺寸精度要求和表面粗糙度要求并应与顶面垂直。
为了保证所钻、铰的孔与顶面垂直并保证工艺孔能在后续的孔系加工工序中使各重要支承孔的加工余量均匀。
根据基准重合、基准统一原则。
在选择工艺孔的加工定位基准时,应尽量选择上一道工序即粗、精铣Φ25下表面工序的定位基准,以及设计基准作为其定位基准。
因此加工工艺孔的定位基准应选择选用Φ45外圆面作为定位基准,用V 型块定位限制4个自由度。
再以Φ25下表面加3个支撑钉定位作为主要定位基面以限制工件的三个自由度。
为了提高加工效率,根据工序要求先采用标准高速钢麻花钻刀具对工艺孔Φ25进行钻削加工;然后采用标准高速钢扩孔钻对其进行扩孔加工;最后采用标准高速铰刀对工艺孔Φ25进行铰孔加工。
准备采用手动夹紧方式夹紧。
等臂杠杆与夹具说明书

目录前言 (2)第1章零件的分析 (4)1.1零件的用途分析 (4)1.2零件的技术要求 (4)1.3零件的工艺分析 (5)1.4确定零件的生产类型 (5)第2章工艺规程设计 (6)2.1确定毛坯的制造形式 (6)2.2确定毛坯的制造方法 (6)2.3基面的选择 (6)2.3.1粗基准的选择 (6)2.3.2精基准的选择 (6)2.4工件表面加工方法的选择 (7)2.5选择加工设备及刀、量、夹具 (7)2.5确定工艺路线 (8)2.5.1工艺路线方案一 (9)2.5.2工艺路线方案二 (9)2.5.3工艺方案的比较和分析 (10)2.6机械加工余量、工序尺寸及毛坯尺寸的确定 (11)2.7确定切削用量与时间定额的计算 (13)第3章夹具设计 (28)3.1确定设计方案 (28)3.2选择定位元件 (28)3.3计算夹紧力并确定螺杆直径 (28)3.4定位误差计算 (29)3.5夹具设计及操作的简要说明 (29)设计心得 (30)参考文献 (31)机械制造技术课程设计任务书题目:设计杠杆零件的机械加工工艺规程及钻2×Ф8孔工序的专用夹具内容:(1)零件——毛坯合图1张(2)机械加工工艺规程卡片1套(3)夹具装配图1张(4)夹具体零件图1张(5)课程设计说明书1份原始资料:该零件图样一张;生产纲领为8000件/年;每日一班。
2016年10月31日前言机械工艺与夹具技术被引入工业领域已经有一百多年的历史了,随着工业的迅猛发展机制工艺与夹具技术更加日新月异。
伴随着数学、控制理论计算机、电子器件的发展,出现了机制工艺与夹具技术系统,并作为一门应用科学已发展成熟,形成了自己的体系和一套行之有效的分析和设计方法。
机械制造工艺学课程设计是在学完了机械制造工艺学(含机床夹具设计)和大部分专业课,并进行了生产实习的基础上进行的一个教学环节。
这次设计使我们能综合运用机械制造工艺学中的基本理论,并结合生产实习中学到的实践知识,独立地分析和解决工艺问题,初步具备了设计一个中等复杂零件(杠杆)的工艺规程的能力和运用夹具设计的基本原理和方法,拟定夹具设计方案。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
摘要根据设计要求首先确定了杠杆臂的基本设计思路,通过对该零件作用分析,形位公差分析、加工工艺、工序设计完成零件的工艺制造思路。
而后确定了定位基准的选择,和夹紧方式的确定,最后经过反复比对后使用三维造型软件进行了初步的草图绘制,确定夹具的外形尺寸,然后设计钻模板和钻套等,为了简化设计减少非标零件的设计和制造成本,选用了较多的螺钉螺母等非标零件。
本次夹具设计过程中夹具采用进行紧凑的设计方案,这样较为节省材料和成本,但是夹具的安装定位显得比较细致,空间利用率较高。
为了方便的放入和取出工件而不对周边产生操作影响和降低生产效率,采用了钻模板的翻转设计模式,左侧的钻模板在非工作时可以方便的拉起,让工件可以顺利放入,安装完毕后翻下钻模板。
【关键字】杠杆臂,工艺,钻夹具,夹紧,定位目录第一章绪论 (3)1.1机床夹具介绍 (3)1.2现代夹具的发展发向 (3)1.3设计目标与任务 (4)1.4 主要研究方向与方法 (4)第二章零件分析 (6)2.1零件的作用 (6)2.2 零件的工艺分析 (6)第三章夹具设计 (8)3.1.夹具的工作原理与结构设计 (8)3.2 夹具的使用方法 (10)3.3 夹具与翻转式钻床的固定 (10)3.5夹紧力计算 (11)第四章:翻转式钻床夹具零件的具体设计 (12)4.1钻床夹具的概括 (12)4.2 夹具零件的设计 (13)4.3夹具体的设计 (14)4.4定位销的设计 (14)4.5 钻模板以及钻套的设计 (14)第五章总结 (21)致谢 (22)参考文献 (23)第一章绪论1.1机床夹具介绍夹具从1787年至今经过了在工业发展初期。
夹具仅作为加工工艺过程中的辅助工具;到后期机床、汽车、飞机等制造业大力发展后,成为主要工艺装备;直到目前近代由于世界科学技术的进步及社会生产力的迅速提高,夹具与机床的紧密结合的一路发展历程看来,夹具在工业生产中的重要地位。
现代生产要求企业制造激烈竞争夹具的应用五花八门,近年来年柔性制造系统(FMS)、数控机床(NC),加工中心(MC)和成组加工(GT)的应用使大批量生产的水平大幅提升。
目前主流的夹具设计要求1.缩短夹具的制造周期快速适用于新产品设计2.提高夹具的通用性特征3.向高精度机床等应用进行发展4.适用于各种现代化制造技术的新型技术5.气压液压等原动力的改进应用来提高装夹效率1.2现代夹具的发展发向现代夹具的发展方向表现为精密化、高效化、柔性化、标准化等四个方面:1.精密化机械产品精度要求快速提高,夹具的精度要求也应该同步提高。
精密化夹具的结构类型很多,比如应用于精密分度的多齿盘的精密夹具。
2.高效化高效化夹具有自动化夹具、告诉化夹具、具有夹紧动力模块的夹具,该类夹具的应用将繁重的体力重复劳动力释放出来,节约了人力成本。
例如高速卡盘则可保证卡爪在高速状态下依然可以能正常夹紧工件,大幅度提高加工的效率。
3.柔性化夹具的柔性化通过调组合方式适应工艺可变因素。
工艺的可变因素主要有:工序特征、生产批量、工件的形状和尺寸等,具有柔性化特征的新型夹具种类主要有:组合夹具、通用可调夹具、成组夹具、模块夹具、数控夹具等,在较长时间内,夹具的柔性化趋向将是夹具发展的主要方向。
4.标准化夹具的标准化与通用化是相关联的,通用化方法包括:夹具、部件、元件、毛坯和材料的通用化夹具的标准化阶段是通用化的深入并为工作图的审查创造了良好的条件。
目前,我国已有夹具零件、部件的国家标准:GB2148~2249-80,GB2262~2269-80以及通用夹具标准,组合夹具标准等。
标准化是柔性化高效化的基础,标准化的发展利于缩短生产准备周期,降低生产总成本。
在现代化的机械和仪器的制造业中,利用夹具来提高加工精度和生产率,减少劳动力成本是主要的目标。
可以预见的是夹具四个方面发展后可保证加工质量降低生产成本。
1.3设计目标与任务本次对于杠杆臂加工工艺及夹具设计的主要任务是:1.完成杠杆臂零件加工工艺规程的制定;2.完成钻孔专用夹具的设计。
3.运用机械制造工艺学课程中的基本理论以及在生产实习中学到的实践知识,正确地解决一个零件在加工中的定位,夹紧以及工艺路线安排,工艺尺寸确定等问题,保证零件的加工质量。
4.提高结构设计能力。
通过设计夹具的训练,获得根据被加工零件的加工要求,设计出高效,省力,经济合理而能保证加工质量的夹具的能力。
5.学会使用手册以及图表资料。
掌握与本设计有关的各种资料的名称,出处,能够做到熟练的运用。
1.4 主要研究方向与方法详细分析零件的主要作用于零件尺寸外形结构,针对尺寸要求与形位公差要求,进行工艺设计和方案对比,择优选择,后续确定零件的粗基准与精基准要求后,针对双工位加工的特点设计出合理的夹紧方式,保证零件的安装与定位得到充分保证。
最后通过三维软件绘制三维夹具,并通过其与cad的转化功能进行转化,修改最后的工程图纸,书写全篇设计论文。
第二章零件分析2.1零件的作用课题给出的零件是机床的杠杆臂。
它的主要的作用是实现机床工作部件启起、停止、变速、变向、操纵机构中的传动装置。
要求该零件有足够的强度和刚度,尺寸精度,形状精度,是机床操纵机构中重要零件,影响机床操纵动作及控制机构装置运动的准确性。
2.2 零件的工艺分析对零件进行工艺分析就是研究、审查零件的结构工艺性。
零件设计是否满足加工的工艺性和经济性要求。
图2.1杠杆臂零件产品图该零件的材料为QT500,球墨铸铁生产工艺简单,铸造性能优良,强度刚度好、以下是杠杆臂零件需要加工表面以及加工表面的位置要求。
该零件是机床操纵结构中一个重要零件,根据产品零件图2.1分析,有四个面需加工,2个垂直平面铣削,3个通孔需钻铰加工(即Ø10+0.1 Ø22+0.28 Ø13+0.12)。
根据产品尺寸公差和形状公差要求,用普通铣床和钻床完全能保证该零件的加工质量。
第三章夹具设计3.1.夹具的工作原理与结构设计3.1.1定位方案与定位元件:为了满足杠杆臂的需要,使杠杆臂左右两端底面定位固定,因不同零件存在一定的误差,应使杠杆臂被加工两孔轴线与钻模板轴线的重合,所以将钻模板固定,又因零件要求为垂直距离,所以设计右端平面固定,左端设置螺旋辅助支撑2进行左右两端垂直距离的调整定位。
使其孔轴线与钻模板轴线重合。
(如图3.2所示)3.1.2夹紧机构:防止钻孔时零件晃动,应对杠杆臂的两端底面以及前后移动进行定位固定,所以在右端设计定位销7、开口垫圈6、夹紧螺母5对零件零件进行固定;定位销7通过垫圈16和六角螺母15固定于夹具体上。
3.1.3其他辅助设备:考虑到零件加工存在误差,所以设计螺旋辅助支撑2可以上下升降,使所有零件都能使左右两端面同时得到固定,为防止误差使加工时上下颠簸,设置锁紧螺母1对螺旋辅助支撑进行锁紧,防止钻孔时辅助支撑受力太大而下降影响加工。
设计可调支撑钉11为防止钻孔时零件前后移动,影响加工精度;设计锁紧螺母10,方便了可调支撑钉11的前后移动,提高了定位固定的精度。
设计定位体17为了使零件右端底面固定精度更高。
(如图3.2所示)图3.1定位零件、固定零件和其他辅助零件螺旋辅助支撑2定位销7锁紧螺母1右底面固定定位体17 左底面固定 可调支撑钉11开口垫圈6 夹紧螺母5锁紧螺母10垫圈16 六角螺母15图3.2定位零件、固定零件和其他辅助零件图3.3夹紧机构3.2 夹具的使用方法被加工零件放在夹具体上时以右端底面与夹具体接触面重合为基准,将被加工零件右端底面放在平面上,调整螺旋辅助支撑2使零件左右底面同时接触夹具,拧紧锁紧螺母1是螺旋辅助支撑固定;调整可调支撑钉11使被加工零件的垂直孔轴线与钻套轴线重合,拧紧定位销7使零件固定于夹具体上。
3.3 夹具与翻转式钻床的固定夹具夹紧杠杆臂后,加工的时候将承受向下、向内的力以及钻孔时的旋转力,夹具将会受力而产生直线以及旋转运动,所以夹具固定在钻床上应受到约束,因夹具夹紧零件加工时,不因受力而产生位移,影响加工精度,所以对夹具的下面以及左面进行固定。
3.4定位误差分析本夹具选用的定位元件为一面两销定位。
其定位误差主要为:销与孔的配合0.05mm,铣/钻模与销的误差0.02mm,铣/钻套与衬套0.029mm由公式e=(H/2+h+b)×△max/H△max=(0.052+0.022+0.0292)1/2=0.06mme=0.06×30/32=0.05625可见这种定位方案是可行的。
3.5夹紧力计算本夹具是在钻床上使用的,用于定位螺钉的不但起到定位用,还用于夹紧,为了保证工件在加工工程中不产生振动,必须对“17”六角螺母和”11”螺母螺钉施加一定的夹紧力。
由计算公式Fj=FsL/(d0tg(α+ψ1’)/2+r’tgψ2)(3-1)Fj-沿螺旋轴线作用的夹紧力Fs-作用在六角螺母L-作用力的力臂(mm)d0-螺纹中径(mm)α-螺纹升角(゜)ψ1-螺纹副的当量摩擦(゜)ψ2-螺杆(或螺母)端部与工件(或压块)的摩擦角(゜)r’-螺杆(或螺母)端部与工件(或压块)的当量摩擦半径(゜)根据参考文献[6]其回归方程为Fj=ktTs其中Fj-螺栓夹紧力(N);kt-力矩系数(cm-1)Ts-作用在螺母上的力矩(N.cm);Fj =5×2000=10000N第四章:翻转式钻床夹具零件的具体设计4.1钻床夹具的概括钻床夹具的特点1)保证工件的加工精度专用夹具应有合理的定位方案,合适的尺寸,公差和技术要求,并进行必要的精度分析,确保夹具能满足工件的加工精度要求。
2)提高生产效率专业夹具的复杂程度要与工件的生产纲领相适应,应根据工件生产批量的大小选用不同复杂程度的高效夹紧装置,以缩短辅助时间,以提高生产效率。
3)工艺性好专用夹具的结构简单合理,便于加工,装配,检验和维修。
专用夹具的生产属于批量生产4)使用性好专用夹具的操作应简单,省力,安全可靠,排屑应方便,必要时可设置排屑机构。
5)经济型好除考虑专用夹具本身结构简单,标准化程度高,成本低廉外,还应根据生产纲领对夹具方案进行必要的经济分析,以提高夹具在生产中的经济效益。
钻床夹具的设计要点1、钻套钻套的作用是确定钻头,铰刀等刀具的轴线位置,防止刀具在加工过程中发生偏斜。
根据使用二点,钻套可分为固定式,可换式,快换式等多种结构形式(1)固定钻套固定钻套直接被压在钻模板上,其位置精度要求较高,但磨损后不易更换,钻模板较薄时,为使钻套具有足够的引导长度,赢采用有肩钻套。
(2)可换钻套在成批生产、大量生产中,为便于更换钻套,采用可换钻套(3)快换钻套在工件的一次装夹中,若顺序进行钻孔、扩孔、铰孔或攻丝等多个工步加工,需要不同孔径的钻套来引导刀具,此时应使用快换钻套。