拨动开关SS-12F15规格书技术参数
拔动开关规格书技术参数SS-12D00
SPECIFICATION
DESIGNATION系列：拨动开关
MODULE NO型号:SS-12D00
0CIRCUIT回路：1P2T
TIMING切换类型：SHORTING
1．STANDARD TEST CONDTTIONS SHALL BE 5 TO 35℃IN TEMPERATURE AND 45 TO 85% IN HUMIDITY。
在40±2℃90-95%RH环境中放96小时,再放在正常环境中,30分钟后进行测试.
8.6
COLD TEST
耐冷试验
At -20±3℃for 96hours,after test
kept in normal condition for 30 min.
在-20±3℃环境中放96小时,再置于正常环境中,30分钟后进行测试.
时间3±0.5秒.
A new uniform coating of solder Shall cover a minimum of 75% of the surface being immersed.
浸入的部分75%以上表面将被锡覆盖。
8.2
RESISTANCE
TO
SOLDERING
HEAT TEST
(3)There shall be no sign of damage mechanically and electrically.
无任何迹象显示机械及电器性能之损坏.
8.5
HUMIDITY TEST
耐湿试验
40±2℃90-95%RH for 96firs after test
keep in mortal condition for 30 min.
RESISTANCE
直流12V光控开关
直流12V光控开关本产品是一种新型的光线自动控制开关。
控制器输入端接交流220V电压，当外界光线强时，输出呈关断状态，当光线暗到一定程度时，控制器接通并输出交流220V电压。
广泛应用于路灯自动控制、监控智能灯光补偿、广告灯箱自动控制、节日彩灯以及家居节能等需要光线控制领域，实现自动控制。
本产品体积小巧、造型美观、工作可靠、安装方便、自身功耗低、控制功率大、并具有防雨设计，是一种用途广泛的自动光控节能开关。
此产品可以根据用户要求，采用12V,24V,36V,48V、220V交直流工作。
常开型光控开关：光线强的时候电路自动断开，光线暗的时候电路自动接通常开型光控开关：光线强的时候电路自动接通，光线暗的时候电路自动断开一、本品特点：1、直流12V光控开关。
2、继电器控制，可承受大电流。
产品分为5A、7A、10A等型号，具体型号和功能简介如下：产品型号(常开型)性能描述LCCF-GK-D125D DC12V 5A延迟型LCCF-GK-D125N DC12V 5A无延迟型LCCF-GK-D127D DC12V 7A延迟型LCCF-GK-D127N DC12V 7A无延迟型LCCF-GK-D1210D DC12V 10A延迟型LCCF-GK-D1210N DC12V 10A无延迟型LCCF-GK-A2205D AC220V 5A延迟型LCCF-GK-A2205N AC220V 5A无延迟型LCCF-GK-A2207D AC220V 7A延迟型LCCF-GK-A2207N AC220V 7A无延迟型LCCF-GK-A22010D AC220V 10A延迟型LCCF-GK-A22010N AC220V 10A无延迟型产品型号（常闭型）性能描述LCCF-GK-D125DN DC12V 5A延迟型LCCF-GK-D125NN DC12V 5A无延迟型LCCF-GK-D127DN DC12V 7A延迟型LCCF-GK-D127NN DC12V 7A无延迟型LCCF-GK-D1210DN DC12V 10A延迟型LCCF-GK-D1210NN DC12V 10A无延迟型LCCF-GK-A2205DN AC220V 5A延迟型LCCF-GK-A2205NN AC220V 5A无延迟型LCCF-GK-A2207DN AC220V 7A延迟型LCCF-GK-A2207NN AC220V 7A无延迟型LCCF-GK-A22010DN AC220V 10A延迟型LCCF-GK-A22010NN AC220V 10A无延迟型3、设有可调电阻，灵敏度可调。
力奥拨动开关的开关说明
力奥生产的拨动开关开关广泛应用于计算机主板的超频和无线通讯、广播电视等设备的调频对码及自动化设备的计算机软件编程。
一、产品规格：
1.额定电压：最大24V max 电流 0.3A
2.开关不常切换的额定电流：最大400mA
东莞震动开关厂家(0769-83629268 13794996161)生产的震动开关,本震动开关适用于，玩具，电动玩具，玩具公仔，防盗器，家用电器，手机数码，电子通讯，电子游戏机，汽车防盗，智能化系统。
其主要的产品有:震动开关，振动开关，弹簧开关，滚珠开关，钢珠开关，角度开关，重力传感器，振动传感器，珠子开关，手珠开关，晃动开关，防盗器开关，敏感度开关，震动弹簧开关，震动钢珠开关，振动角度开关，震动滚珠开关，防盗专用震动感应器360度振动开关、全方位360度无角度限制震动开关、触摸开关、红外线开关、倾斜震动感应触发开关、水准感应器滚珠开关、声光控延时开关，振动开关- 钢珠开关- 震动弹簧开关- 滚珠开关 ，东莞振动开关,钢珠开关,滚珠开关,震动弹簧开关等电子开关产品的厂家,制造各类电子开关(钢珠开关,滚珠开关,震动弹簧开关）
SS拨动开关产品型号列表:
SS-11G1(IP1T),SS-12D00(1P2T),SS-12D03(1P2T),SS-12DO6(1P2T),S-12D07(1P2T),SS-12D13(1P2T),SS-12E17(1P2T),SS-12E21(1P2T),SS-12F02(1P2T),SS-12F04(1P2T),SS-12F08(1P2T),SS-12F15(1P2T),SS-12F16(1P2T),SS-12F17(1P2T),SS-12F21(1P2T),SS-12F22(1P2T),SS-12F23(1P2T),SS-12F24(1P2T),SS-12F25(1P2T),SS-12F32(1P2T),SS-12F34(1P2T),S-12F39(1P2T),SS-12F41(1P2T),SS-12F43(1P2T),SS-12F44(1P2T),SS-12F47(1P2T),SS-12F48(1P2T),SS-12F49(1P2T),SS-12F55(1P2T),SS-12F76(1P2T),SS-12F93(1P2T),SS-12I06(1P2T),SS-12J01(1P2T),SS-13D07(1P3T),SS-13F03(1P3T),SS-13F07(1P3T),SS-13F07(1P3T),SS-13F11(1P3T),SS-13F12(1P3T),SS-13F24(1P3T),SS-16F03(1P6T),SS-17F01(1P7T),SS-22D07(2P2T),SS-22D10(2P2T),SS-22D32(2P2T),SS-22F01(2P2T),SS-22F04(2P2T),SS-22F05(2P2T),SS-22F06(2P2T),SS-22F07(2P2T),SS-22F11(2P2T),SS-SSF12(2P2T),SS-22F16(2P2T),SS-12F17(2P2T),SS-22F20(2P2T),SS-22F22(2P2T),SS-22F24(2P2T),SS-22F25(2P2T),SS-22F32(2P2T),SS-22F43(2P2T),SS-22F70(2P2T),SS-22H02(2P2T),SS-22H07(2P2T),SS-22GO8(2P2T),SS-22I24(2P2T),SS-J01(2P2T),SS-22J03(2P2T),SS-22J12(2P2T),SS-22K22(2P2T),SS-22K35(2P2T),SS-22L05(2P2T),S-22L24(2P2T),SS-23D03(2P3T),SS-23D07(2P3T),SS-23D08(2P3T),SS-23D14(2P3T),SS-23D25(2P3T),SS-23D32(2P3T),SS-23D33(2P3T),SS-23E01(2P3T),SS-23E03(2P3T),SS-23E04(2P3T),SS-23E08(2P3T),SS-23E09(2P3T),SS-23E26(2P3T),SS-23F02(2P3T),SS-23F03(2P3T),SS-23F19(2P3T),SS-23F24(2P3T),SS-23F33(2P3T),SS-23F35(2P3T),SS-23F54(2P3T),SS-23H02(2P3T),SS-23H03(2P3T),SS-23H11(2P3T),SS-23H25(2P3T),SS-23I01(2P3T),SS-23L02(2P3T),SS-24D01(2P4T),SS-24D02(2P4T),SS-24E01(2P4T),SS-24E04(2P4T),SS-24E04(2P4T),SS-24F01(2P4T),SS-24H01(2P4T),SS-24H02(2P4T),SS-24H03(2P4T),SS-24N01(2P4T),SS-25F02(2P5T),SS-25H03(2P5T),SS-26D02(2P6T),SS-26F01(2P6T),SS-26F02(2P6T),SS-29D01(2P9T),SS-32F01(3P2T),SS-32H01(3P2T),SS-33F01(3P3T),SS-42D02(4P2T),SS-42D04(4P2T),SS-42D24(4P2T),SS-33F01(3P3T),SS-442D02(4P2T),SS-42D04(4P2T),SS-42D24(4P2T),SS-42F01(4P2T),SS-42F11(4P2T),SS-42H03(4P2T),SS-42H04(4P2T),SS-42H06(4P2T),SS-42H08(4P2T),SS-42H14(4P2T),SS-43D01(4P3T),SS-43D02(4P3T),SS-43D04(4P3T),SS-43D06(4P3T),SS-44D01(4P4T),SS-44D04(4P4T)
拨动开关规格书
测试.
器性能.
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -40
±2℃AND A HUMIDITY OF
90%TO96% FOR 96 HOURS,
3.5
HUMIDITY TEST 潮湿试验
THEN THE SWITCH SHALL BE MINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR
5.000CYCLES AT A SPEED OF 25-30 CYCLES
负荷:在负荷的条件下以分钏25-30次的频率作5.000回之无
负荷测试.
1/0
第 页,共 页
3.DURABILITY 耐久性:
ITEM项目
TEST CONDITIONS 测试条件
PERFORMANCE 表现
SOLDER BATH METHOD: SOLDER TEMPERATURE
放置在温度-20±3℃中96小时后,再放置常温中1小时来进
行测试.
THE SWITHCH SHALL BE STORED AT A TEMPERATURE OF
85±2℃ FOR 96 HOURS,THEN THE SWITCH SHALL BE
THERE SHALL BE NO
3.4
HEAT TEST 耐热试验
CHARACTERISTICS SHALL BE
SATISFIED.
本体
无变形,能满足于机械,电器
性能.
3.2
SOLDERABILITY TEST
THE SOLDER BATH OF 230±5℃ FOR 3±0.5 SECONDS. 温 度为230±5℃,时间为3±0.5秒.
#JC986A型无线调频对讲收音机
兰州理工大学计算机与通信学院通信项目专业高频电子线路课程设计设计题目：986A型对讲机设计学院专业班级学号姓名指导老师时间年学期目录一、设计实验目的无线对讲机作为一种简单的通讯工具，因为它不需要中转和地面交换机站的支持，就可以进行移动通信，所以深受人们欢迎。
目前广泛用于生产、保安、野外项目等领域的小范围的通信项目中。
无线对讲机技术是很多无线通信技术的基础，目前应用较广泛的蜂窝式移动电话技术，就是在无线双工对讲机的基础上发展起来的新兴现代通信技术。
对讲机的电路形式很多，从调制方式可分为调幅式和调频式；从收发功能上，可以分为单工式和双工式。
单工式对讲机同一时间内，只能工作在一种状态下，即：接收或发射状态，而不能同时处于收发状态。
单工式对讲机工作时，要不停的切换开关来控制收发状态，所以使用起来不太方便。
但单工式对讲机，则因为它造价低，体积小，耗电低等优点，所以被大量使用。
而双工式对讲机，可以收发电路同时工作，使用起来如同普通电话机一样，应用起来也比较方便，但是因为双工对讲机电路复杂，造价高，耗电大等缺点，所以应用较少。
学生通过对调频对讲机安装与调试，可对所学过的高频电子线路中各单元的电路形式、各电路间的耦合方式及信号传送波形和结果有更深的了解。
同时，也对以前所学过的各类型模拟单元电路的工作原理、电路形式、调试方法、测试方法、测量技术、整机电路统调技巧等方面得到了全面的、系统的训练。
为今后从事本专业工作奠定了坚实的技术基础。
二、设计指标本套件用的是DIP插件，电路板较紧凑，要求制作者细心，认真。
对讲的发射极高、性能稳定、耗电省、输出功率大等优点。
只要按要求装配无误，装好后稍加调试即可，无需统调，是学习电子技术的理想套件。
它既能相互对讲，不接收9V收发转换过程。
四、详细单元电路设计4.1电路工作原理三极管Q1和耦合可调电感线圈T1，电容器C4，C2等组成振荡电路，产生频率约为49.8MHZ的载频信号。
Q2,Q3,Q4,Q5和相关电阻电容等组成低频放大电路。
世伟洛克弯管器(精)
使用手册语言 德语 日语
西班牙语
代号 -G -J -S
例：MS-BTB-1-1-E
4. 添加一成套件代号。
工具成套件
台式 英制铝制弯管架槽和钢制滚轮 (1/2、5/8、3/4、
7/8 和 1 in.) 公制铝制弯管架槽和钢制滚轮 (12、16、18、
20、22 和 25 mm)
电动式 英制弯管架槽、滚轮架和管夹 (1、1 1/4、1 1/2
弯曲半径 近似值
壁厚，最小／最大
碳钢
不锈钢
尺寸，in.
4
0.049/0.120 0.065/0.120
5
0.065/0.180 0.083/0.156
6
0.083/0.220 0.090/0.188
8
0.095/0.220 0.109/0.188
公制卡套管
卡套管 外径
25 32 38 50
最小卡套 管管长
67
1.2/2.8
82
1.2/3.0
1.8/3.0
1.8/3.0 112
2.0/3.0
4 工具和附件
台式和电动式弯管机 订购信息
1. 选择一基本订购号。
弯管机类型
订购号
台式
手动
MS-BTB-M
电动—110 V (ac)
MS-BTB-1
电动—230 V (ac)
MS-BTB-2
电动式
115 V (ac)
壁厚) 和 12 至 30 mm 外径 (1.0 至 3.0 mm 壁厚) ■ 钢制弯管架槽需装配：
■ 壁厚超过 0.095 in. 的外径为 1 in. 的卡套管 ■ 壁厚超过 2.4 mm 外径为 25 mm 的卡套管 ■ 所有尺寸的 SAF 2507™ 卡套管 ■ 所有尺寸的厚壁退火不锈钢卡套管 ■ 所有尺寸的冷拔 1/8 硬度的不锈钢无缝卡套管 ■ 包含有加油枪和用于存放的金属手提箱 ■ 可以使用可选的扭矩离合器和支撑臂用一个 1/2 in. 电钻机进行操作 ■ CE 认证
GRTE lighting control product selection 说明书
灯光控制产品手册9025系列面板9025 KNX 系列面板是一组触控开关，专门用于灯光控制管理，同时，按键也可配置为其他应用，用于控制智能楼宇。
MINISWITCH 系列面板P14MINIPAD 系列面板P16客房管理系统P21执行器P259025系列面板P4TOUCHPANEL 系列面板P12传感器和系统组件P37目录KNX电容式开关KNX电容式开关9025系列面板9025系列面板GRES-CS-J01-KNX电容式开关底座 - 白色GRES-CS-J05-KNX电容式开关底座 - 黑色9025系列KNX 控制面板，可选配2、4、6、8、10触控按键的电容式开关按钮。
每个按钮都可以配置为开/关命令，调光命令，百叶窗控制，场景调用和顺序控制等功能。
产品内置两级比例积分温度控制逻辑，可控制开启加热、制冷设备、阀门、两管制或四管制的风机盘管等。
9025系列产品带有嵌入式温度传感器和一个后部连接端子，可外接数字或模拟量输入 （如传感器、传统按钮等）。
定制型号的9025系列产品，其玻璃盖板上的图标可定制和替换，当某项功能启用时，玻璃盖板上与该项功能相匹配的图标将被点亮。
该设备配有KNX 通信接口。
9025盖板技术特点尺寸•（宽 x 高 x 深）96 x 96 x 36 mm 电源• KNX 总线供电，21 ~ 32 Vdc 输入 - 数字型 • 干接点类型•最大长度≤10 m 绞合电缆输入 - 模拟型 接温度探头• GRTE-SEN （范围-20 ~ +100 °C ）• GRTE-SEN-2（范围-50 ~ +60 °C ）• 最大长度≤20 m 绞合电缆GRESG2CHJ01-ACC玻璃 2通道 - 白色GRESG2CHJ05-ACC玻璃 2通道 - 黑色GRESG4CHJ01-ACC玻璃 4通道 - 白色GRESG4CHJ05-ACC玻璃 4通道 - 黑色GRESG6CHJ01-ACC玻璃 6通道 - 白色GRESG6CHJ05-ACC玻璃 6通道 - 黑色GRESG8CHJ01-ACC玻璃 8通道 - 白色GRESG8CHJ05-ACC玻璃 8通道 - 黑色GRESG1CHJ01-ACC玻璃 10通道 - 白色GRESG1CHJ05-ACC玻璃 10通道 - 黑色订购代码GRESG2CHJ01-ACC玻璃 2通道 - 白色GRESG4CHJ01-ACC玻璃 4通道 - 白色GRESG6CHJ01-ACC玻璃 6通道 - 白色GRESG8CHJ01-ACC玻璃 8通道 - 白色GRESG1CHJ01-ACC玻璃 10通道 - 白色GRESG2CHJ05-ACC玻璃 2通道 - 黑色GRESG4CHJ05-ACC玻璃 4通道 - 黑色GRESG6CHJ05-ACC玻璃 6通道 - 黑色GRESG8CHJ05-ACC玻璃 8通道 - 黑色GRESG1CHJ05-ACC玻璃 10通道 - 黑色KNX带温度/湿度面板KNX带温度/湿度面板9025系列面板9025系列面板GRET-CT-J01-KNXKNX电容式开关底座带温度 - 白色GRETCTHJ01-KNXKNX电容式开关底座带温度/湿度 - 白色GRET-CT-J02-KNXKNX电容式开关底座带温度 - 黑色GRETCTHJ02-KNXKNX电容式开关底座带温度/湿度 - 黑色技术特点尺寸•（宽 x 高 x 深）96 x 96 x 36 mm电源• KNX总线供电，21 ~ 32 Vdc输入-数字型• 干接点类型• 最大长度≤10 m绞合电缆输入 - 模拟型接温度探头• GRTE-SEN（范围-20 ~ +100 °C）• GRTE-SEN-2（范围-50 ~ +60 °C）• 最大长度≤20 m绞合电缆订购代码9025温度/湿度系列盖板GRETGCTJ03-ACC玻璃住宅显示屏 - 白色GRETGCTJ04-ACC玻璃住宅显示屏 - 黑色GRETGCTHJ03-ACC玻璃酒店显示屏 - 白色GRETGCTHJ04-ACC玻璃酒店显示屏 - 黑色GRETGCTJ03-ACC玻璃住宅显示屏 - 白色GRETGCTJ04-ACC玻璃住宅显示屏 - 黑色GRETGCTHJ03-ACC玻璃酒店显示屏 - 白色GRETGCTHJ04-ACC玻璃酒店显示屏 - 黑色9025温控器是一款KNX室内温度控制器，包含7个可配置的电容式按键，用于开/关、调光、电动百叶窗控制、场景调用、顺序控制以及本地温度控制等。
镇江市电工器材厂 JN15-12 31.5户内高压接地开关 说明书
w w w .d g q c c .c o m 0511********w w w.d g q c c .c o m w ww.d gq c c .c o m 051182976667w ww .d gq c c .co m w w w .d g q c c .c o m 0511********w w w.d g q c c .c o m JN15-12/31.5户内高压接地开关安装使用说明书镇江市电工器材厂w w w .d g q c c .c o m 0511********w w w .d g q c c .c o m ww ww.d gq c c .c o m w w w .d g q c c .c o m 0511********w ww.d g qc c .co m 1产品概述JN15-12/31.5型户内高压接地开关是集国内外接地开关最新技术而开发的一种具有先进水平的产品，经全面考核，其性能符合GB 1985-89«交流高压隔离开关和接地开关》及IEC129的要求，适用于额定电压12kV 及以下三相交流50Hz 的电力系统中，可与各种型号高压开关柜配套使用，作接地保护用，并可带有电压显示装置。
2、使用环境条件2.1环境温度上限+40℃，下限–l0℃，注：允许在-25℃时储运2.2海拔不超过1000米2.3相对湿度：日平均值不大于95%，月平均值不大于90%水蒸汽压：日平均值不大于2.2×10-3M pa ，月平均值不大于1.8×10-3Mpa2.4周围空气应不受腐蚀性或可燃气体、水蒸汽等明显污染。
2.5无经常性的剧烈振动。
注：如与上述条件不符请与制造商协商解决3、型号及其代表意义：3、技术参数4.1额定电压：12kV4.24s 热稳定电流(有效值)：1.5kA 4.3动稳定电流(峰值)：80kA4.4关合电流(峰值)：80kA4.5额定绝缘水平：雷电冲击耐压：75kV 主回路1min 工频耐压：42kV 二次回路1min 工频耐压：2kVw w w .d g q c c .c o m 0511********ww w .d g q c c .c o m w w w .d g q c c .c o m 0511********w w w .d g q c c .c o m w w w .d g q c c .c o m 0511********w w w.d g q c c .c o m 5、结构及工作原理JN15-12型户内高压接地开关由底架、触刀、绝缘子(传感器〉、合闸弹簧、触座及三相短路连接铜管组成。
JN15-12接地开关安装使用说明书
中科电力装备集团有限公司JN15型户内高压接地开关安装使用说明书微软用户安全第一！接地开关只能安装于适合电气设备工作的户内场所；必须保证现场电气设备安装条件的适用性与安全性；确保由专业人员来进行安装、操作和维护；有关接地开关的一切操作，都应遵守本说明书的相应规定；使用中不要超过接地开关正常工作条件下技术参数的规定值；说明书应放置在与安装、操作及维护有关的人员方便拿到的地方；用户的专职人员应对所有影响安全的事项负责，并正确使用接地开关；若对本使用说明书尚有疑问，我们很乐意为您提供进一步咨询。
目录1、概述 (4)2、型号的表达方式 (4)3、产品依据标准 (4)4、使用环境条件 (4)5、接地开关主要技术参数 (4)6、产品结构及工作原理 (5)7、外形及安装尺寸图 (5)8、接地开关内部电气原理图 (10)9、运输储存 (10)10、中期储存 (11)11、安装 (11)12、调试与操作 (12)13、维修 (13)14、产品随机提供以下文件 (14)15、产品订货须知 (14)1、概述JN15系列户内交流高压接地（以下简称接地开关）是三相交流50Hz、额定电压为12～40.5kV 的户内高压开关设备。
在电力系统中与多种型号高压开关柜配套使用，亦可作为高压电器设备检修时接地用。
2、型号的表达方式3、产品依据标准ZN63（VS1）-12系列接地开关设计和制造符合GB1985 《高压交流隔离开关和接地开关》、GB/T11022 《高压开关设备和控制设备的共用技术要求》、IEC60129 《高压交流隔离开关和接地开关》等标准的相关要求。
4、使用环境条件4.1正常使用条件a）环境温度最高温度：+40℃；最低温度：-15℃；日平均温度值不超过+35℃。
b）环境湿度相对湿度：日平均值≤95%，月平均值≤90%；水蒸气压：日平均值≤2.2KPa，月平均值≤1.8KPa。
c）设备安装场所海拔高度不超过1000米。
美国海利威尔公司V15系列微型基本开关说明书
V15 SERIESMICRO SWITCH Standard Miniature Basic Switches004945Issue 12DESCRIPTIONHoneywell’s MICRO SWITCH V-Basic Standard Switch, V15 Series is anelectromechanical switch designed to provide outstanding value in a reliable global package. This switch is often ideal for “low-cost-of-failure” applications, where the cost is minimal to replace or service any failure related to the switch. With a wide variety of operating forces, and amperage ratings, the V15 is designed for numerous types of applications.Available in both pin plunger and levered styles, the V15 Series also offers a multitude of termination styles to fit almost any application.DIFFERENTIATION• Choice of actuation, termination, and operating characteristics that can allow for flexibility in numerous types of applications• With a broad current capacity, one switch package can control a wide range of electrical loadsAPPLICATIONS• Appliances • Furnaces• Gaming machines • Ice makers • Power washers • Vending machinesVALUE TO CUSTOMERS• Wide choice of electrical ratings: 0.1 A, 5 A, 10 A, 16 A, 22 A, 26 A • Certified for global use: UL/cUL, ENEC, CQC• Available with pin plungers or integral levers to meet multiple application and equipment requirementsFEATURES• Broad range of electrical loads: 0.1 A, 5 A, 10 A, 16 A, 22 A, 26 A • Long service life: over one million mechanical operations• Gold contacts are also available for controlling logic level/low energy circuits• World-wide package size acceptance • UL/CSA, cUL, ENEC, and CQC approvals• Variants with cadmium-free and optimized contacts availableHoneywell offers a wide range of MICRO SWITCHthe large basic switches,Sensing and Internet of Things 3V15S05 PRODUCT NOMENCLATURE V15Switch TypeTemperatureGradeSLeverPositionElectrical Rating05V15 Series Standard Basic SwitchTerminal TypeCircuit Code—ZAOperating Force(at pin plunger max)200Mounting HolesKALever Type06Special DesignatorC—Housing Type1V15T10 PRODUCT NOMENCLATUREV15Switch TypeTemperatureGradeTLever PositionElectrical Rating10V15 Series Standard Basic SwitchTerminal TypeCircuit Code—ZAOperating Force(at pin plunger max)200Mounting HolesKALever Type06A special designator letter is used only when there is a special modificationto the switch.Review Product Specification to determine the exact differences. Below is an example.Special DesignatorC—Housing Type1V15H16/T16/T22/H22/T26 PRODUCT NOMENCLATURE V15Switch TypeTemperatureGradeHLever PositionElectrical Rating16V15 Series Standard Basic SwitchTerminal TypeCircuit Code—ZAOperating Force(at pin plunger max)200Mounting HolesKALever Type06Special DesignatorC—Housing Type1PinPlunger4 ShortStraightLeverStandardStraightLeverSensing and Internet of Things 5LongStraightLeverSimulatedRoller6 ShortRollerLeverSensing and Internet of Things 7RollerLever8 Sensing and Internet of Things 9MOUNTING DIMENSIONSFIGURE 1. V15 SERIES STANDARD SWITCH DIMENSIONSFIGURE 2. V15 SERIES METRIC MOUNTING HOLE DIMEN-SIONS FOR Ø 3 MM PINS OR SCREWSMetric mounting for Ø 3 mm pins or screws Ø 3,10 mm +0,10 mm/-0,05 mm 10,3 m m ±0,1 m m Ø 0.12 in +0.004 in/-0.002 in mounting holeFIGURE 3. V15 SERIES USA MOUNTING HOLE DIMENSIONS FOR #4 SCREWSUS mounting for #4 screws - K Designator Ø 2,90 mm +0,10 mm/-0,05 mm10,3 m m ±0,1 m m Ø 0.11 in +0.004 in/-0.002 in mounting holeFIGURE 4. V15 SERIES HOUSING DIMENSIONS10 Sensing and Internet of Things 1112 STANDARD LEVER OPTIONS • DIMENSIONSFIGURE 19. V15 SERIES A01/STRAIGHT SHORT LEV erFIGURE 20. V15 SERIES A02/STANDARD STRAIGHT LEVERFIGURE 21. V15 SERIES A03/LONG STRAIGHT LEVERFIGURE 22. V15 SERIES A04/SIMULATED ROLLER LEVERFIGURE 23. V15 SERIES A05/SHORT ROLLER LEVERFIGURE 24. V15 SERIES A06/ROLLER LEVERNOTE: These dimensions apply for the “A” lever position. For the “B” leverposition, please add 5,7 mm [0.224 in].Position APosition BWARRANTY/REMEDYHoneywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicablewarranty period. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgment or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages.While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer’s sole responsibility to determine the suitability of the product in the application.Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this writing.However, Honeywell assumes no responsibility for its use.004945-12-EN | 12 | 08/20© 2019 Honeywell International Inc. All rights reserved.m WARNINGIMPROPER INSTALLATION• Consult with local safety agenciesand their requirements whendesigning a machine-control link, interface and all control elements that affect safety.• Strictly adhere to all installationinstructions. Failure to comply with theseinstructions could result in death or serious injury.m WARNINGMISUSE OFDOCUMENTATION•The information presented in this product sheet is for reference only. Do not use this document as a product installation guide.•Complete installation, operation, and maintenance information is provided in the instructions supplied with each product.Failure to comply with theseinstructions could result in death or serious injury.HoneywellSensing and Internet of Things 830 East Arapaho Road Richardson, TX FOR MORE INFORMATIONHoneywell Sensing and Internet of Things services its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing, or the nearest Authorized Distributor, visit or call:USA/Canada +302 613 4491Latin America +1 305 805 8188Europe +44 1344 238258Japan +81 (0) 3-6730-7152Singapore +65 6355 2828Greater China+86 4006396841RELATED DOCUMENTATIONThe following associated literature is available on the Honeywell web site at :• Installation instructions• Product part listing/nomenclature tree• Product application-specific information– Application note: Electronic sensorsand eectromechanical switches in valves and flow meters – Application note: Electronic sensorsand MICRO SWITCH switches in industrial air compressors – Application note: Sensors andswitches for potential HVAC/R applications – Application note: Sensors andswitches for valve monitors and valve indicators – Application note: Sensors andswitches in sanitary valves – Case study: Switching it up– Technical bulletin: Applying precision switches。
JC986A型对讲机实训报告
JC986A型对讲机实训报告题目 JC986A型对讲机姓名专业班级指导教师日期 201 年月日目录摘要 (3)绪论 (3)JC986A型对讲机电路图及其工作原理说明 (4)1、原理框图2、制作原理电路图3、电路原理分析4、元器件清单JC986A型对讲机的制作步骤与调试 (7)1、制作步骤及注意事项2、安装与调试3、问题处理4、实训成果实训总结 (8)参考文献 (9)摘要在现代通信中，对讲机是一种近距离的、简单的无线传输通信工具。
目前，它广泛应用于生产、保安、野外工程等小范围移动通信工程中。
本JC986A型对讲机是一款专用的对讲机，发射频率是49.8MHZ，2套对讲机构成一对，使用时用9V电池。
电路简洁，整机制作比较容易，装配成功率高，具有遥控距离远，声音大等特点。
它是由接收部分和发射部分组成。
接收部分采用直接接收的方式，采用LC振荡电路检波，检波后音频信号再由低频放大器放大，最后由耦合电容推动扬声器发声；发射时，由扬声器讲话音信号变成电信号后，再经低频放大电路、调制电路，最后将已调波从天线发送出去。
关键词：通信、对讲机、焊接、调试一、绪论随着社会的发展，对讲机的应用越来越广泛，它主要用于短距离声音的传输，经常被用在公安、酒店、宾馆、旅游、建筑场地等。
对于我们电子信息工程专业的学生而言，明白对讲机的工作原理是非常必要的。
对讲机声音的传播要依靠电磁波来完成。
电磁波是由电磁震荡产生的。
发射功率的大小直接影响到对讲机发射信号的强弱，同时对讲机之间的功率是否匹配将直接影响传输距离的远近。
发射功率越大，发射信号覆盖的范围越大，在功率匹配的情况下通话的距离也就越远。
但是，在实际中发射功率也不能太大，大的发射功率不仅影响原件的寿命，而且由于干扰噪声的存在则会引起很强的干扰。
天线用于发射和接收电磁波，发射天线将高频电流转换为电磁波，向空中发射传播信息，并将电磁波转换为高频电流。
天线的增益越大，驻波比越小，发射或接受的能力越强。
轻 触 开 关 说 明 书说明书
1.General specification 基本说明1.1Scope 范围This specification covers the requirements for single key switches which have no keytop(TACT SWITCHES:MECHANICAL CONTACT ). 此规范含盖单推柄和无推柄的轻触开关要求。
1.2Operating Temperature Range 使用温度范围-55 to 125 ℃(normal humidity, normal press).正常湿度，标准压力1.3Storage Temperature Rang 保存温度范围-25 to 85 ℃(normal humidity, normal press).1.4Test Conditions 测试条件Tests and measurements shall be made in the following standard clnditions unless otherwise specified:测试和计量按下列标准条件除非特殊说明Normal temperature (temperature 5 to 35℃) 标准温度Normal humidity (relative humidity 45 to 85%) 正常湿气Normal pressure (pressure860 to 1060 mbars ) 标准压力In case any question arises from the judgement made, tests shall be conducted in the following conditions：Temperature (20±2℃) 温度Relative humidity (65±5%) 相对湿度Pressure (860 to 1060 mbars) 压力2. APPEARNCE, STYLE, AND DIMENSIONS 外形，类型和尺寸2.1Appearance 外形There shall be no defects that affect the serviceability of the product 外形必须无缺陷才不影响产品适用性2.2 Style and Dimensions 类型和尺寸Shall conform to the assembly drawings. 符合装配图3.TYPE OF ACTUATION 动作类型Tactile feedback 轻触返回4. CONTACT ARRANGEMENT 1 poles 1 throws 接触形式1接点1 回路(Details of contact arrangement are given in the assembly drawings).细接点形式在装配图中5. MAXOMUM RATINGS DC 12 V 50 mA 最大额定值APPD CHKD DSGDTD-309XA1/7ZONE SYMB DATE APPD CHKD DSGD6.2Mechanical机械特性Item 项目Test Condition试验条件Requirements规格6.2.1. Actuating Force 动作力Placing the switch such that the direction of switchoperation is vertical and then gradually increasing theload applied to the center of the stem, the maximum loadrequired for the stem to come to a stop shall bemeasured.开关的动作方向为垂直放置开关向推柄中心逐渐增加负荷直到推柄停止时所测量的最大负荷160±30gf6.2.2. Travel 行程Place the switch such that the direction of switch operation isvertical and then apply a static load twice the actuating force tothe center of the stem, the travel distance for the stem to come toa stop shall be measured.开关的动作方向为垂直放置开关,并以双倍动作力的静负荷作用推柄中心,测量推柄从开始到停止的行程距离0.15±0.1mm6.2.3.Return Force 返回力The sample switch is installed such that the direction ofswitch operation is vertical and, upon depression of thestem in its center the whole travel distance ,the force ofthe stem to return to its free position shall be measured.开关的动作方向垂直放置开关，在已有行程的推柄中心向上减小压力，推柄回到自由位置时所测量到的力40gf min6.2.4. Stop Strength 静止强度Placing the switch such that the direction of switchoperation is vertical, a static load of 3 kgf shall beapplied in the direction of stem operation for a period of60 seconds.开关的动作方向为垂直放置开关，在推柄动作方向施加3 KG的静负荷，60秒时间There shall be no sign ofdamage mechanically andelectrically无机械的和电气的损伤迹象6.2.5. Stem Strength 推柄的强度Placing the switch such that the direction of switchoperation is vertical, the maximum force to withstand apull applied oppsite to the direction of stem operationshall be measured.开关的动作方向为垂直放置开关从推柄动作方向反方向施加拉力所测量到的最大承受力3 kgfAPPD CHKD DSGDTD-309XA2/7ZONE SYMB DATE APPD CHKD DSGDTACT SWITCH SPECIFICATION( 轻触开关说明书)6.PERFORMANCE 性能6.1 Electrical 电气Item 项目Test Condition试验条件Requirements 要求6.1.1.Contact Resistance 接触电阻Applying a static load twice the actuating force to thecenter of the stem, measurements shall be made witha 1 kHz small-currentcontact resistance meter.用两倍的动作力作静负载施加于按钮的中心，并用1 千赫小电流接触电阻仪测量100 mΩmax.6.1.2. Insulation Resistance绝缘电阻Measurements shall be made following application ofDC 100 V potintial across terminals and acrossterminals and frame for one minute.在端子之间，端子与外壳之间施加DC100V，一分种100 MΩmin6.1.3. Dielectric Witstanding voltage电气耐压AC250V (50Hz or 60Hz) shall be applied acrossterminals and across terminals and frame for oneminute.在端子与端子之间，端子与外壳之间施加AC250V(50Hz or60Hz)There shall be mo breakdown没有击穿6.1.4. Bounce 抖动Lightly striking the center of the stem at a rateencountered in normal use ( 3 to 4 operations persec ), Bounce shall betested at “ON” and “OFF”在正常使用中(以每秒3-4 次周期)轻轻地在手柄中心加力，在通与断瞬间测试抖动。
德力西电气 CDQ1F双电源自动转换开关产品样本2023年第1版 产品说明书
CDQ1F PC级自动转换开关产品样本2021年9月第一版北京办事处地址：北京市丰台区枫竹苑一区（未来假日花园）18-10 邮编：100076天津办公点地址：天津市西青区凯安道凯信佳园9－3－401邮编：300100沈阳办公点地址：辽宁省沈阳市于洪区细河南路碧桂园银河城钻石郡148-3邮编：110000长沙办公点地址：湖南长沙市芙蓉区万象企业公馆5栋2709邮编：410000郑州办公点地址：河南郑州金水区青年路145号6号楼17层1706号邮编：450000武汉办公点地址：湖北武汉市江汉区新华路186号福星国际商会大厦2516、2517室邮编：430000温州办公点地址：浙江省乐清市柳市镇德力西工业园邮编：325604成都办公点地址：成都市金牛区人民北路二段118号金牛万达广场甲级Ｃ座 16楼1603号邮编：610000南京办公点地址：江苏省南京市秦淮区洪武路23号隆盛大厦1505、1506室邮编：210000重庆办公点地址：重庆市九龙坡区渝洲路4号18－9号邮编：400039广州办事处地址：广州市荔湾区南岸路63号城启大厦1905室 邮编：510160南宁办公点地址：南宁市西乡塘区北大路中梦泽园小区岳阳阁5单元202室邮编：530003昆明办公点地址：昆明市西山区棕树营街道办事处土堆村碧鸡名城C地块9幢2802室邮编：650000贵阳办公点地址：贵阳市观山湖区石林东路中天帝景传说B区B4栋1单元1302室西安办事处地址：陕西西安市莲湖区大庆路三号蔚蓝国际A705 邮编：710082新疆办公点地址：新疆乌鲁木齐市米东区米东南路红光雅居D区6号楼3单元602室邮编：830000青岛办公点地址：青岛市城阳区正阳路177号15号楼2单元903室邮编：214000福建办公点地址：福州市晋安区东二环泰禾广场7号楼1117单元邮编：350024济南办公点地址：山东省济南市历下区工业南路55号未来城商务中心13#楼608室邮编：250000杭州办公点地址：杭州市江干区蓝桥景苑11幢2单元1002室邮编：310016南昌办公点地址：江西南昌市西湖区广场东路恒茂国际华城23幢2907邮编：330002深圳办公点地址：深圳市龙华新区民丰路1号碧水龙庭7栋4单元14D 邮编：518109兰州办公点地址：兰州市城关区瑞德摩尔万国港E座2208邮编：730020电话：153****1522合肥办公点地址：安徽省合肥市瑶海区武里山路五里山天街3A-1402室邮编：230000吉林办公点地址：吉林省长春市经开区浦东路与深圳街交汇处虹湾国际A座706室邮编：130031黑龙江办公点地址：黑龙江省哈尔滨市道外区润达国际D座2单807室邮编：150050石家庄办公点地址：石家庄市裕华区华兴生活小区41－1－102邮编：050011太原办公点地址：山西太原市万柏林区西矿街70号红星小区五单元1402邮编：030024石家庄物流地址：河北省石家庄市元氏县殷村石武铁路东国达物流园内电话：155****1257辽宁物流地址：沈阳市苏家屯区雪莲街188号（雪莲街与四环路交叉口）华翔东北亚贸城 D1 德力西陕西物流地址：陕西省西安市六村堡丰产路西段陕西商储物流园南区B1号德力西仓库山东物流地址：山东省临沂市经济技术开发区翔宇路23号华派克物流园内 重庆物流地址：重庆市江津区珞璜工业园B区重庆西部诚通物流有限公司5号库成都物流地址：四川省成都市青白江区国际集装箱物流园区德汇路9号4栋4-4号广东物流地址：广东省佛山市南海区里水镇怡和二路银裕木业制品厂直入100米河南物流地址：河南省郑州市经济开发区国际物流园喜达路宇培物流园（礼通路）东北W4-A区4B 58-59号湖北物流地址：湖北省武汉市东西湖区临空港大道23号捷利物流园3号库温州物流地址：浙江省乐清市柳市镇德力西高科技生态工业园新疆物流地址：乌鲁木齐市友谊路230号（新疆诚通国际物流园内德力西仓库）芜湖物流地址：安徽省芜湖市芜湖县新芜经济开发区朝阳路德力西物流中心0102符合的标准正常使用及安装条件CDQ1F 型自动转换开关电器，由负荷隔离开关（无过载和短路保护机构）和智能控制器组成。
MICRO SWITCH V15系列标准小型基本按钮说明书
V15 SERIESMICRO SWITCH Standard Miniature Basic Switches004945Issue 15VALUE PROPOSITIONThe Honeywell MICRO SWITCH V-Basic Standard Switch, V15 Series is an electromechanical switch designed toprovide outstanding value in a reliable global package. This switch is often ideal for “low-cost-of-failure” applications, where the cost is minimal to replace or service any failure related to the switch. With a wide variety of operating forces,and amperage ratings, the V15 is designed for numerous types of applications.APPLICATIONSPresence DetectionEnsures door latching and safe operationFloat SwitchOn/off power to stop overflow conditionsFlow SwitchEnables safe and efficient water usagePower SwitchReliable system control for motors, pumps, fansOperator ControlsInterface control for system auxiliary functionsV15S05 PRODUCT NOMENCLATURE V15Switch TypeTemperatureGradeSLeverPositionElectrical Rating05V15 Series Standard Basic SwitchTerminal TypeCircuit Code—ZAOperating Force(at pin plunger max)200Mounting HolesKALever Type06Special DesignatorC—Housing Type1V15T10 PRODUCT NOMENCLATUREV15Switch TypeTemperatureGradeTLever PositionElectrical Rating10V15 Series Standard Basic SwitchTerminal TypeCircuit Code—ZAOperating Force(at pin plunger max)200Mounting HolesKALever Type06A special designator letter is used only when there is a special modificationto the switch.Review Product Specification to determine the exact differences. Below is an example.Special DesignatorC—Housing Type1V15H16/T16/T22/H22/T26 PRODUCT NOMENCLATURE V15Switch TypeTemperatureGradeHLever PositionElectrical Rating16V15 Series Standard Basic SwitchTerminal TypeCircuit Code—ZAOperating Force(at pin plunger max)200Mounting HolesKALever Type06Special DesignatorC—Housing Type1Figure 2. V15 Series Metric Mounting Hole Dimensions for Ø 3 mm pins or screwsFigure 3. V15 Series USA Mounting Hole Dimensions for #4 screwsMOUNTING DIMENSIONSFigure 1. V15 Series Standard Switch DimensionsMetric mounting for Ø 3 mm pins or screwsØ 3,10 mm +0,10 mm/-0,05 mm 10,3 m m ±0,1 m m Ø 0.12 in +0.004 in/-0.002 in mounting holeUS mounting for #4 screws - K Designator Ø 2,90 mm +0,10 mm/-0,05 mm 10,3 m m ±0,1 m m Ø 0.11 in +0.004 in/-0.002 in mounting holeFigure 4. V15 Series Housing DimensionsSTANDARD LEVER OPTIONS • DIMENSIONSFigure 19. V15 Series A01/Straight Short LeverFigure 20. V15 Series A02/Standard Straight LeverFigure 21. V15 Series A03/Long Straight LeverFigure 22. V15 Series A04/Simulated Roller LeverFigure 23. V15 Series A05/Short Roller LeverFigure 24. V15 Series A06/Roller LeverNOTE: These dimensions apply for the “A” lever position. For the “B” leverposition, please add 5,7 mm [0.224 in].Position APosition B004945-15-EN | 15 | 07/22© 2022 Honeywell International Inc. All rights reserved.HoneywellAdvanced Sensing Technologies 830 East Arapaho Road Richardson, TX V15V19Applications requiring precision, long term reliability, and design flexibility in electrical ratingsCost sensitive applications requiring configurability in actuation, termination, and operating characteristicsApplications in major and small appliances or designs that require simple configurationsIndustry standard switch footprintand global certifications ideal for“low-cost-of-failure” applicationsMultiple Contact Material Contact variants to enable design WARRANTY/REMEDYHoneywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicablewarranty period. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgment or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages.While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer’s sole responsibility to determine the suitability of the product in the application.Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this writing.However, Honeywell assumes no responsibility for its use.m WARNINGIMPROPER INSTALLATION• Consult with local safety agenciesand their requirements whendesigning a machine-control link, interface and all control elements that affect safety.• Strictly adhere to all installationinstructions. Failure to comply with theseinstructions could result in death or serious injury.m WARNINGMISUSE OFDOCUMENTATION•The information presented in this product sheet is for reference only. Do not use this document as a product installation guide.•Complete installation, operation, and maintenance information is provided in the instructions supplied with each product.Failure to comply with theseinstructions could result in death or serious injury.RELATED DOCUMENTATION• V Basics Range Guide • Applying Precision Switches • V7 Datasheet • V15 Datasheet• Product application-specific information– Application note: Electronic sensorsand electromechanical switches in valves and flow meters – Application note: Electronic sensorsand MICRO SWITCH switches in industrial air compressors – Application note: Sensors andswitches for potential HVAC/R applications – Application note: Sensors andswitches for valve monitors and valve indicators – Application note: Sensors andswitches in sanitary valves – Case study: Switching it up– Technical bulletin: Applying precision switches。
XGN15-12箱型固定式户内交流金属封闭开关设备
XGN15-12箱型固定式户内交流金属封闭开关设备1.概述XGN15-12 户内SF6环网柜是我公司引进国外先进技术并按照国内农电及城网改造之要求而生产的新一代高压电器产品。
适合国内农电及城网改造，用于交流50Hz 12kV 的电力网络中，特别适用于二次变电站，开闭所等，作为电能的接收和分配之用。
本设备可用于发电厂、变电站、大型建筑、高层楼宇、机场、医院、剧院、体育场、港口、地下设备、工矿企业等。
2.产品特点z可扩展式SF6环网柜组合的随意性优于SF6充气环网单元，体积小、安全可靠；z应用SF6气体作绝缘和灭弧介质，恒定磁场旋弧方式使其灭弧能力强，开断性能好、过电压小、电气寿命长、灭弧室免维护；z柜体结构采用敷铝锌板经多重折弯成形，采用插接式拼装，坚固牢靠；z结构紧凑简单、外形美观、布局合理，加上现代传感技术和最新保护继电器，以及先进的技术性能和轻便灵活的组装方案更加适应市场的变化；z柜壳密度高，防止设备受杂物和动物侵入，防护等级IP3X；z安装方便、操作灵活、具有多重可靠的机械联锁和防止误操作功能；z可选配上电动机构、PT、CT、UPS、FTU等可用于配电自动化。
3.正常使用条件z周围空气温度：上限+40℃，下限-25℃；z相对湿度：日平均不大于95%，月平均不大于90%；z海拔高度：不超过1000m；z没有火灾、爆炸危险、严重污秽及剧烈震动的场所。
（注：超出以上使用条件时，用户应与制造厂协商。
）z地震烈度不超过８度。
4.符合标准z GB 3906 《3～35kV交流金属封闭开关设备 》z GB/T 11022 《高压开关设备和控制设备的共同技术要求》z DL/T 404 《户内交流高压开关柜订货技术条件 》z IEC 60298 《额定电压1kV以上52kV及以下交流金属封闭开关设备和控制设备》 z IEC420 《交流高压负荷开关-熔断器组合电器》5.型号含义X G N 15 - 12额定电压(kV)设计序号 户内装置 固定式箱型开关设备6.技术参数表一.开关柜技术参数序号名称单位数据1额定电压 kV12 2额定频率 Hz 50/601min 工频耐受电压42（隔离断口：48） 3额定绝缘水平雷电冲击耐受电压kV75（隔离断口：85）4额定电流 A630 5额定短时耐受电流（3S ） 256额定峰值耐受电流 kA637配用最大高压熔断器 A125 8额定电流开断次数 1009机械寿命 次500010 防护等级IP3X11外形尺寸（宽*深*高） kA 375(500)*940*1635(1885)表二.熔断器的选择熔断器的选择应根据受保护变压器容量和系统短路容量计算确定：选择原则可“IEC787――用于变压器回路的高压熔断器熔丝的选择使用导则”。
JN15-12接地开关安装使用说明书
中科电力装备集团有限公司JN15型户内高压接地开关安装使用说明书微软用户[选取日期]安全第一！接地开关只能安装于适合电气设备工作的户内场所；必须保证现场电气设备安装条件的适用性与安全性；确保由专业人员来进行安装、操作和维护；有关接地开关的一切操作，都应遵守本说明书的相应规定；使用中不要超过接地开关正常工作条件下技术参数的规定值；说明书应放置在与安装、操作及维护有关的人员方便拿到的地方；用户的专职人员应对所有影响安全的事项负责，并正确使用接地开关；若对本使用说明书尚有疑问，我们很乐意为您提供进一步咨询。
目录1、概述 (4)2、型号的表达方式 (4)3、产品依据标准 (4)4、使用环境条件 (4)5、接地开关主要技术参数 (4)6、产品结构及工作原理 (5)7、外形及安装尺寸图 (5)8、接地开关内部电气原理图 (10)9、运输储存 (10)10、中期储存 (11)11、安装 (11)12、调试与操作 (12)13、维修 (13)14、产品随机提供以下文件 (14)15、产品订货须知 (14)1、概述JN15系列户内交流高压接地（以下简称接地开关）是三相交流50Hz、额定电压为12～40.5kV 的户内高压开关设备。
在电力系统中与多种型号高压开关柜配套使用，亦可作为高压电器设备检修时接地用。
2、型号的表达方式3、产品依据标准ZN63（VS1）-12系列接地开关设计和制造符合GB1985 《高压交流隔离开关和接地开关》、GB/T11022 《高压开关设备和控制设备的共用技术要求》、IEC60129 《高压交流隔离开关和接地开关》等标准的相关要求。
4、使用环境条件4.1正常使用条件a）环境温度最高温度：+40℃；最低温度：-15℃；日平均温度值不超过+35℃。
b）环境湿度相对湿度：日平均值≤95%，月平均值≤90%；水蒸气压：日平均值≤ 2.2KPa，月平均值≤1.8KPa。
c）设备安装场所海拔高度不超过1000米。
拨动开关
东莞市华宁电子有限公司
Tel：0769-83563263 Fax：0769-83563267
批准：
审核：
拟制：
e 额定值 DC 12V 0.5A
c 外观 无重要注塑制陷,无重要废品.
耐压
. 手感 动作灵活无卡滞,按力手感相对一致.
c 材料 MATERIAL
序号
零件名称
材料
o 1
手柄
尼龙 PA
m 2
盖板
冷扎钢
电路转换 可焊性 防护等级 耐焊锡热 接触电阻 绝缘电阻
数量
1 1
手柄类型 HANDLE TYPE
A: G B: VG
用≤8V、0.15A 的电气检查，电路通断正常。 粘锡面积为浸入面积 95%以上。 IP68 260±5℃/5s 功能动作与电路转换正常,外观质量完好。 ≤30 毫欧 ≧100 兆欧
备注
黑色 电镀
3
弹片
磷铜
1
复银
4
底座
尼龙 PA
1
黑色
5
端子(引脚)
黄铜
1
电镀
产品名称: 产品型号: 单 位:
拨动开关
SS-12D02
文件编号 SS-12D07（RoHS）
www.huanin 高度HEIGHT g X 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0
代号 20 30 40 50 60 70 80 90
e 主要技术参数及性能 MAIN SPECIFICATIONS
l 接触型式 1P2T
切换类别 NON-SHORTING
MICRO SWITCH V15W2系列基本开关产品说明书
V15W2 SERIES Basic Switch for Hazardous LocationsDESCRIPTIONMICRO SWITCH V15W2 Series basicswitches are precision snap-actioncontact mechanisms enclosed inplastic cases. Switch actuation triggersthe mechanical closure of the switch’scontacts. The switches are approved foruse in Zone 2 hazardous locations. Whilea small amount of arcing occurs betweenthe switch contacts during contactclosure, the switch is environmentallysealed so that flammable gases cannotenter into the switching cavity. This minimizes the chances of ignitionof flammable gases in a hazardous atmosphere.The ATEX and IEC Ex approvals are:Ex nC IIA T5 Gc for an ambient temperature range of -25 °C to +85 °C per EN/IEC 60079-0 andEN/IEC 60079-15 via certificates DEKRA 19ATEX0013U and IEC Ex DEK 17.0053U.DIFFERENTIATION• ATEX and IEC Ex approvals• Wide variety of actuators, connections, operating and electrical characteristics • More durable performance within a range of conditions• Operates under many difficult/harsh environmental conditionsFEATURES• Approved for use in Zone 2 hazardouslocations; ATEX and IEC Excertifications• IP67 equivalent• UL, cUL, ENEC, and CQC certificationsfor ordinary (non-hazardous) locations• 5 A electrical rating• Longer service life: over one millionmechanical operations• Quick-connect terminals• SPDT, SPNO, SPNC• 100 gf, 200 gf operating forces• Available with a variety of actuators• Global package size acceptance• Gold contacts are also available forcontrolling logic-level/low-energycircuitsPORTFOLIOThe MICRO SWITCH V15W2Series basic switch is partof a broad Honeywell switchportfolio. Globally compliant andknown worldwide for their compact andlightweight design, MICRO SWITCHsnap-action switches are designedfor more accurate repeatability andextended life.To view the entire product portfolio,click here.VALUE TO CUSTOMERS• V-Basic switches for potential use inrefrigeration units using alternativesfor HFC and HCFCs, specificallytargeting OEMs and Tier white goodsmanufacturers transitioning to lowerGHA emission refrigerants (which tendto be more explosive) per EPA andother regulatory guidance• Certified for use in ordinary locationsvia UL, cUL (North America), CQC(Asia-Pacific), and ENEC (Europe).Certified for use in hazardouslocations via ATEX (Europe) and IEC Ex(International)POTENTIAL APPLICATIONS• Appliances (especially with newrefrigerants)• Valve actuators• Commercial refrigeration• Ice makers• HVAC/R (furnace, refrigeration,ventilation)32336117Issue F2 FIGURE 1. PRODUCT NOMENCLATURENot all combinations of model code are available.V15W2Switch Type ALever Location02Lever TypeContact MaterialMICRO SWITCH Hazardous Location-Rated V15W2 BasicSwitchETerminals ZCircuitry200Mounting HolesOperating Force—W2Electrical Rating (must be included)—ASpecial DesignatorA special designator code is used to indicate some such as a special actuator, wire color,etc. Review product specification to of the non-standard feature. This code will consist of up to three alphanumeric characters. A blank designates no difference from standard listing.FIGURE 2. MOUNTING DIMENSIONSSensing and Internet of Things 34 WARRANTY/REMEDYHoneywell warrants goods of its manu-facture as being free of defective materi-als and faulty workmanship during the applicable warranty period. Honeywell’s standard product warranty applies un-less agreed to otherwise by Honeywell in writing; please refer to your order ac-knowledgment or consult your local sales office for specific warranty details. If war-ranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages.While Honeywell may provide applica-tion assistance personally, through our literature and the Honeywell web site, it is buyer’s sole responsibility to determine the suitability of the product in the ap-plication.Specifications may change without notice. The information we supply isbelieved to be accurate and reliable as of this writing. However, Honeywell assumes no responsibility for its use.32336117-F-EN | F | 02/20© 2020 Honeywell International Inc. All rights reserved.m WARNINGPERSONAL INJURYDO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury.Failure to comply with theseinstructions could result in death or serious injury.m WARNINGMISUSE OFDOCUMENTATION•The information presented in this product sheet is for reference only. Do not use this document as a product installation guide.•Complete installation, operation, and maintenance information is provided in the instructions supplied with each product.Failure to comply with theseinstructions could result in death or serious injury.ADDITIONAL MATERIALSThe following associated literature is available at :• Product range guide• Product installation instructions • Application notes • CAD drawings • Product imagesHoneywellSensing and Internet of Things 9680 Old Bailes Road Fort Mill, SC 29707 FOR MORE INFORMATIONHoneywell Sensing and Internet of Things services its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing, or the nearest Authorized Distributor, visit or call:International +815 618 3231USA/Canada+302 613 4491。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
DEFORMATION OR CRACKS IN MOLDED PART.
外观无异常,满足于机械、电器性能。
6.6
HUMIDITY
TEST
潮湿试验
THE SWITCH SHALL BE STORED AT A
TEMPERATUREOF 40±2℃AND A HUMIDITY
OF 90% TO 95% FOR 96 HOURS.THEN THE
SWITCH SHALL BE MAINTAINED AT STANDARD
ATMOSPHERIC CONDITION FOR 1 HOUR AFTER
WHICH MEASUREMENT SHALL BE MADE.
放置40±2℃的相对温度为90%~95%环境中96小时后,再将样版放在正常环境1小时后进行测试.
输入500V DC电压1分钟,按以下接触方法测试;
(1)外壳兴排脚之间.
(2)端子之间.
100 MΩ MIN
100兆欧以上。
4.3
DIELECTRIC
STRENGTH
耐电压
AC 500V (50-60HZ)FOR 1 MIN TRIP CURRENT:0.5 mA
(1)BETWEEN TERMINALS.
CYCLES AT A SPEED OF 15 TO 18 CYCLES
PER MINUTE WITHOUT LOADING.
无负荷:
在无负荷的条件下以每分钟15-18回的
速度进行10,000次的测试.
（1）CONTACT RESISTANCE（接触电阻）
100mΩ MAX,100毫欧以下。
（2）INSULATION RESISTANCE（绝缘电阻）
IMMERSION DEPTH UP TO
THE SURFACE OF THE BOARD
THICKNESS OF PRINTED WIRING BOARD
1.6 mmDIMENSIONS OFCOMPONENT
HOLES IN THE PRINTED WIRING BOARD SHALL SEING ACCORDANCE WITH THOSE
SCALE:
CHK’D
SWITCHING LIFE 10K CYCLES (15-18C/M UNIOADING)
BY
东莞市振鑫电子有限公司
DRWG NO
DATE:2005.5.10
VERSION:1
东莞市振鑫电有限公司
文件编号
SF-SP-0372
发布日期
2006年5月29日
SPECIFICATION规格书
5.3
DISPLACEMENT
OF ACTUATOR
(KNOB)
柄强度
A STATIC LOAD OF 10 N(1K gf)SHALL BE APPLIED
TO THE TOP OF THE ACTUATOR(KNOB) AND THEN
DISPLACEMENT SHALL BE MEASURED TO THE DIR-ECTION OF THE ARROW.
第A版
第2页共3页
6.ENDURANCE CHARACTERISTICS(耐久性):
ITEM项目
TIST CONDITIONS测试条件
PERFORMANCE规格
6.1
LIFE
TEST
寿命试验
ENDURANCE WITHOUT LOADING：
A SWITCH SHALL BE SUBJECTED TO 10，000
6.7
STANDARD
ATMOSPHERIC
CONDITIONS
测试标准状态
UNLELL OTHERWISE SPECIFIED.
THESTANDARDRANGEOF ATMOSPHERIC
CONDITIONS FOR MAKING MEASUREMENTS
AND TESTS ARE AS FOLLOWS:
第A版
第1页共3页
MODEL NO.
产品名称.拨动开关
DRAWN制订
白春莲
APPD.审批
1.RATING (额定值) :DC 50V0.3A
2.FUNCTION (接触型式) :1P2T
3.TIMING (时间特性) :NOT-SPECIFIED
4.ELECTRICAL CHARACTERISTICS (电气性能规格):
（1）AMBIENT TEMPERATURE : 5℃TO 35℃
（2）RELATIVE HUMIDITY :45% TO 85%
（3）AIR PRESSURE :86kpa TO 106kpa
在没有指定的情况下测试温度、湿度、气压如下:
（1）温度为5~35℃.
（2）湿度为45% TO 85%.
（3）气压为86kpa TO 106kpa.
外观无异常,满足于机械、电器性能。
东莞市振鑫电子有限公司
文件编号
SF-SP-0372
发布日期
2006年5月29日
SPECIFICATION规格书
第A版
第3页共3页
6.5
HEAT TEST
耐热试验
THE SWITCH SHALL BE STORED AT A
TEMPERATURE O 70±2℃FOR 48 HOURS.
BE SATISFIED.
本体无变形,能满足于机械、电器性能。
6.4
COLD TEST
耐冷试验
THE SWITCH SHALL BE STORED AT A
TEMPERATURE OF -25±3℃FOR 48 HOURS.
THEN THE SWITOH SHALL BE
MAINTAINED AT STANDARD
SPECIFIED IN THIS SPECIFICATION.
焊炉焊接的时候时候控制在260±5℃，过炉时间3±0.5秒，于（基板）厚度为1.6 mm
WITHOUT DEFORMATION OF CASE OR
EXCESSIVE LOOSENESS OF TEMINALS
ELECTRICAL CHARACTERISTICS SHALL
RESISTANCE
绝缘电阻
APPLY A VOLTAGE OF 500V DC FOR 1 MIN.
TO FOLLOWING PORTIONS AFTER WHICH
MEASUREMENT SHALL BE MADE.
(1)BETWEEN BODY AND TERMINAL.
(2)BETWEEN TERMINALS.
THEN THE SWITCH SHALL BE MAINTAINED
AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT
SHALL BE MADE.
放置在温度70±2℃中测试48小时后,再放置正常室温中1小时来测定.
ATMOSPHERIC CONDITIONS FOR 1 HOUR
AFTER WHICH MEASUREMENT SHALL BE
MADE.-25±3℃中48小时后,再放置常温
常温中1小时来进行测试。
THERE SHALL BE NO DEFORMATION
OR CRACKS IN MOLDED PART.
ISSUED
SPECIFICATION
TITLE:SLIDE SWITCH
MODEL NO:SS-12F-15
CONTACT RESISTANCE:30mohm Max
INSULATION RESISTANNC:100Mohm at 500V DC
UNIT:MM
DWN
DPERATION FORCE:REFER ATTACH SPECIFICATION
3mmFROM THE TIP OF THE ACTUATOR (KNOB).
在距离胶柄前端3 mm作测定点.
300gf±100gf
5.2
TERMINAL
BTRENGTH
端子强度
A STATIC LOAD OF 300 gf SHALL BE APPLIED
TO THE TERMINAL FOR 15 SEC.IN ANY DIRECTION
(测试后外表无损伤,并且满足机械性能)
6ห้องสมุดไป่ตู้2
SOLDERA-
BILITY
TEST
可焊性试验
THE TOP OF THE TERMINALS SHALL BE
DIPPED2mmIN THE SOLDERBATHOF
230±5℃FOR 3±0.5 SECONDS.
端子顶部被浸入锡焊池中2 mm深,温度
为230±5℃,时间为3±0.5秒。
ITEM项目
TEST CONDITIONS测试条件
PERFORMANCE规格
4.1
CONTACT
RESISTANCE
接触电阻
MEASURED AT 1KHZSMALL CURRENT(100mA OR LESS)
在1KHZ微小电流(100 mA以下)测试.
30mΩ MAX.
30毫欧以下。
4.2
INSULATION
(2)BETWEEN TNDIVIDUAL TERMINAL AND FRAME.
输入AC 500V(50-60 HZ)电压,1分钟感度电流为0.5 mA,按以下接触方法测试:
(1)排脚相互之间
(2)排脚兴外壳之间
WITHOUT DAMAGE TOPARTS ARCINCINC OR BREAKDCMN, ETC.