模具中英文对照

合集下载

模具名称中英文对照

站脚 = Distance Spacer
行位导向键 = Slider Certer Rail
行位镶件 = Slider Insert
斜边 = Angular Pin
方斜边 = Angular Cam
铲鸡 = Locking Block
行位压板 = Slider Guide Rail
进入位 = gate location
水口形式 = gate type
大水口 = edge gate
细水口 = pin-point gate
水口大小 = gate size
转水口 = switching runner/gate
唧嘴口直径 = sprue diameter
直身杯司 = Straight Bushing
有托杯司 = Shoulder Bushing
方定位块 = Position Block Set
定= Parting Lock
中托司套 = Ejector Lead Bushing
拉杆 = Support Pin
拉杆定位介子 = Support Pin Spacer
齿轮 = Gear
丝杆 = Screw
轴承 = Bearing
油缸 = Oil Cylinder
气缸 = Air Cylinder
间隔圈 = Spacer Ring
垃圾钉 = Slopper Ring
二板模 = 2-plate mold
边钉/导边 = leader pin/guide pin
边司/导套 = bushing/guide bushing
中托司 = shoulder guide bushing

模具中英文对照

film gate 薄膜形浇口
finger pin 指形梢
finish machined plate 角形模板
finish machined round plate 圆形模板
fixed bolster plate 固定侧模板
flanged pin 带凸缘销
flash gate 毛边形浇口
head punch 顶头冲孔
headless punch 直柄冲头
heavily tapered solid 整体模蕊盒
hose nippler 管接头
impact damper 缓冲器
injection ram 压射柱塞
inlay busher 嵌入衬套
inner plunger 内柱塞
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
king pin 转向梢

模具术语中英文对照

模具术语中英文对照模具(Mold) - A shaped cavity or matrix into which molten or uncured material is poured so thatupon solidification it will take on the shape of the cavity.注射模(Injection mold) - A molding cavity created by injecting material into a mold via a runner system.常用于塑料件注塑。

压铸模(Die casting mold) - A metal mold created for die casting processes, usually zinc, copper or aluminum based alloys.充型范(Pattern) - A full sized model of the desired casting, used to create the mold cavity in processes like sand casting.冒口(Sprue) - The primary vertical channel through which liquid material is poured into mold cavities.冒口通过主要供料道向模板腔内引入熔融金属。

气孔(Vent) - A small channel allowing the gases formed (by vaporization,chemical reaction etc.) to escape from mold cavity.用来排出模具腔内气体的小通道。

流道(Gate) - The channel that conveys molten metal from the sprue into the mold cavity.将熔融金属从主流道(冒口)引入模腔的小槽道。

模具中英文对照

模具中英文对照表
搬运固定板防呆装置快速定位安全侧销保管垫块平衡垫块停止垫块氮气缸到底记号镶块素材定位器进退料支架脱料板顶料块下模钢块行程定位具废料刀废料盒废料滑槽折边刀块定位键凸轮组件凸轮滑动座凸轮驱动座凸轮侧滑块切刀块分块导柱导套导柱组缓冲垫块挡板（块）垫块垫圈固定块作用套管安全套管滚轮（组）优力胶弹簧卸模停止具侧销 H型顶料机构 UPPER DIE UPPER DIE HOLDER LOWER DIE LOWER DIE BOTTOM HOLDER DIE PAD SAFETY GUARD WEARPLATE HOOK INSERT HOOK FIX IN PLATES FOOL PROOFING QUICK CLAMP RETAINER PIN SETS(SAFETY) BLOCKS BALANCER BLOCK STOPER BLOCK NIIROGEN SPRING CHECK BUTTONS INSERT BLOCK NEST GUIDE SKID BRACKETS STRIPPER DIE LIFT BLOCK LOWER STEEL STROKE END BLOCK SCRAP CUTTER SCRAP BOX RETAINER BOLT FLANGE DIE LOCATING KEYS CAM UNIT CAM SLIDE CAM DRIVER CAM SIDE SLIDE CUTTER BLOCK SECTIONAL BLOCK GUIDE POST GUIDE BUSH GUIDE POST SET CUSHION PLATE BAFFLE PLATE WASHER FIXED PLATE SPOOL RETAINER SAFE STOPER BOLT RUBBER ROLLER(ASSEMBLY) STOCK BLOCKS COIL SPRING UNLOAD DIE STOPER BLOCK SIDE PIN H LIFTER UNIT 零件详细检具气缸接头 C式快速接头三向接头万向接头 L型快速接头 T型快速接头阀调速阀方向控制阀定位销开口销带头销固定销夹管连接管通气管 PVC管行程端管轴连杆轴焊接树脂消音器螺帽有槽螺帽销规冲母座承盘柱塞端子箱集头座内六角螺栓内螺纹圆柱销吊挂弹簧导销工法图上模平面下模平面断面冲头衬套冲头固定座盖板垫板打料器托架柄曲柄下料排样图 PARTS DETAIL CHECKING FIXTURE CYLINDER ADAPTER(AUGMTURE) QUICK NIPPLE THREE-WAY CONNECTOR UNIVERSAL-JOINT ADAPTER L JOINT T JOINT VALVE COVERNOR VALVE DIERCTIONAL CONTROL VALYE LOCATION PIN SPLIT PIN PIN WITH HEAD DOWEEL PIN CLAMP PIPE CONNECTOR AIR VENT AIR TUBE STROKE END PIPES SHAFT LINK SHAFT WELDING RESIN MUFFLE NUT SLOTTED NUT GUAGE BUSH(BUTTON DIE) RETAINER PLUNGER CABLE CONNECTING BOX CONNERTOR SUPPORT S.H.C.SCREW DOWEL PIN RETAINER BOLT SPRING GUIDE RETAINERS DIE LAYOUT ,PROCESS SHEETS UPPER DIE OF PLAN VIEW LOWER DIE OF PLAN VIEW SECTION PUNCH BUTTON RETAINER SAFETY GUARD BACKING PLATE KNOCK OUT PIN BRACKET HANDEL CRANK STRIP LAYOUT OF BLOCK

模具常用名称中英文对照表

23. 螺钉：Screw——缩写：Scw
24. 电极：Electrode——缩写：Elc
25. 限位：LIMIT——缩写：LT
26. 导向板：GUIDE PLATE——缩写GUP
27. 直顶块： STRAIGHT EJ BLOCK——缩写STB
28. 补强板： STIFFENING PLATE——缩写STP
5. 热流道板(热浇道板)：Hot runer——缩写：HR
6. 母模（定模）：Cavity——缩写：Cav
7. 导柱：Guide Pin——缩写：G.P.
8. 导套：Guide bush——缩写：G.B.
9. 复位杆：Release Pin——缩写：R.P.
10. 动模型芯（中间体）：Core——缩写：Cor
11. 模脚：Support parallels——缩写：Supa
12. 侧翼块：Side block——缩写：Sibk
13. 轮Leabharlann ：Plin——缩写：Plin 14. 模座（底座）：Die holder——缩写：Dho
15. 镶件：Insert——缩写：Ins
16. 滑块（行位块）：Slide——缩写：Sld
模具数模命名规则及常用名称中英文对照表（含缩写）
1. 射嘴：Nozzle——缩写：Noz
2. 定位圈：locating ring——缩写：locr
3. 浇口套：Sprue bush(Sprue busing) ——缩写：Sprb
4. 垫板(固定板)：Base Plate——缩写：BP
17. 斜顶块：Lifter——缩写：Lit
18. 推板(顶板)：Eject Plate——缩写：EP

模具术语中英文对照

模芯Parting Core / 局部视图Partial View / 冷料# Cold Slag / 线切割Wire E.D.M / 轮廊Contour/螺纹孔Tapping Hole / 连接件Fittings / 斜针Angle Pin / 接合Engage替换镶件Interchangeable Mold Inserts / 指定吨位的注塑机Specific Press水嘴接头Water Fittings / 螺纹Eyebolt Thread / 回针Stop Pin二级顶出针Sub-Leaderd Pin / 镶件Mold Insert/加硬Harden唧嘴Sprue / 设计筒图Design Preliminary / 名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold 三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板A'plateB板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High V olume Running Mold剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension雕刻Engrave托司EJ.GUIDE PINGating TypeSprueEdge/TabSubPin PointFanCashewHot Sprue/TipHot ValveHot RunnerOther: Best case gating in order for the parts to de-gate at ejection旋转镶件circumvolve Insert螺纹抽芯Thread action insert电镀plating备件spare part弯头elbow组装、冲压、喷漆等专业词汇Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条形码 barcode scanner条形码扫描仪 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造技术 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs.inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板chassis |'∫æsi| 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接柆键 sheet metal parts 冲件 plastic parts塑料件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |'plein?|刨床 miller铣床 grinder磨床 driller钻床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager |'depjuti| =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |'skræpid|报废 scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良 oxidation |' ksi'dei?n|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embeded lump|in'bed| |l?mp|镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 name of a department部门名称 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper 扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots 水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering 工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker 模工 production, to produce生产 equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defective product box不良品箱 die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 carton box纸箱 to pull and stretch拉深 to put material in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模 to feed, feeding送料 transportation运输 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 evaluation评估 prepare for, make preparations for 准备 parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程 to revise, modify修订 to switch over to, switch---to throw--over switching over切换 engineering, project difficulty工程瓶颈 stage die 工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 stamping, press冲压 punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder 油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to control管制 to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice 通知 application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 common vocabulary for die engineering模具工程常用词汇 die 模具 figure file, chart file图档 cutting die, blanking die 冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch 拉伸 Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second count 复盘点数量 quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品 incoming material to be inspected进货待验 description品名 steel/rolled steel钢材 material statistics sheet 物料统计明细表 meeting minutes会议记录 meeting type 会别 distribution department分发单位 location地点difference quantity 差异量 cause analysis原因分析 raw materials原料 materials物料 finished product成品 semi-finished product半成品 packing materials包材 good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods处理品 warehouse/hub仓库 on way location在途仓 oversea location海外仓 spare parts physical inventory list备品盘点清单 spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割 EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket for the punch head挂钩槽 slug hole废料孔 feature die公母模 expansion dwg 展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销 round pierce punch=die button圆冲子 shape punch=die insert 异形子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块 club car高尔夫球车 capability能力 parameter参数 factor系数 phosphate 皮膜化成 viscosity涂料粘度 alkalidipping脱脂 main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗 alkaline etch龄咬 desmut 剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条形码 flow chart流程窗体 assembly组装 stamping冲压 molding成型 spare parts=buffer备品 coordinate坐标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕疪 shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring 镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄 crank shaft曲柄轴 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the multiple keys花键 quenching淬火 tempering 回火 annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机模具工程类 plain die简易模 pierce die冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点 dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 material材质 material thickness料片厚度 factor系数 upward向上 downward向下 press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 weight重量 total wt.总重量 punch wt.上模重量五金零件类 inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销 coil spring弹簧 lifter pin顶料销 eq-height sleeves=spool等高套筒 pin销 lifter guide pin浮升导料销 guide pin导正销 wire spring圆线弹簧 outer guiding post外导柱 stop screw止付螺丝 located pin定位销 outer bush外导套模板类 top plate上托板（顶板） top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下垫板 die holder下夹板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲子 bending block折刀 roller滚轴 baffle plate挡块 located block定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate定位板 sliding block滑块电镀plating。

模具常用中英文对照

模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割 Wire E.D.M轮廊Contour螺纹孔 Tapping Hole连接件 Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针 Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner V ents抛光Draw Polish侧抽芯 Side Action加强筋 Reinforcing三角撑 Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting 装卸孔 Handling Hole运输安全带 Moldstrap码模槽 Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location耐落胶 Teflon Paste偏移量 Offset水塞Water Line Plug撬模脚 Ppy Slot重新加工Reworked配件Components补偿Compensation平面度 Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机 Edm熔接线 Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰 Flange方铁 Spacer Block顶针板 Ejector Plate顶针底板Ejector Retainer Plate垫板 Retainer Plate后模镶针Core Pin拉圾钉 Stop Pin有托顶针Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套 Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet V alve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速项 Accelerated Ejector客户 Client产品名 Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件 Sub-Insert下模小镶件 Core Sub-Insert上模小镶件 Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机） Jaw硬片（摩擦片） Wear Plate水口铁 Runner Bar上模水口铁 Upper Runner Bar下模水口铁 Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁 Side Lock斜度锁 Interlock锁模板 Safety Bar‘O’令（密封圈） O'Ring喉塞Plug隔水片 Baffle波子螺丝（行位定位螺丝） Ball-Catch斜顶Lifter控制开关Switch回针 Return Pin斜导柱 Angle Pin推板 Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板 Ejector Plate顶针底板Ejector Retainer Plate垫板 Retainer Plate垃圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套 Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet V alve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速顶 Accelerated Ejector扁顶 Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板 Backup合模Shutoff空隙槽 Clearance Slot导柱及导套 Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具 Thermoset Mold三板模 3-Plat Mold分型面 Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板 Retainer Plate顶出板 Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器 Bumper衬垫Cushion公差Tolerance突然性动作 Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模 Sticking Core粘水口 Sticking Sprue夹水纹 Weld Line变形 Warpage走水不平均 Filling Uneven走不齐 Short Shot挂成品 Part Hanging漏水 Water Leakage刮花（擦伤）Galling困气 Air Trapping温度 Temperature注塑模※※※※ction Mold 入水 Gate试板 Sampling压力 Pressure倒圆 Fillet顶棍 Ejector顶白 Stress Mark粘前模 Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边） Angle PinA板 A'plateB板 B'plate倒扣 Under-Cut披峰 Flash缩水 Sink Mark氮化 Nitride不规则四边形Trapezoid连续的 Consecutive雕刻 Engrave出模角 Draft分模面 Parting Surface擦位 Shut-Off(S/0)导套 Bushing回针 Return Pin加硬 Harden唧嘴 Sprue设计筒图Design Preliminary丝印 Silkprint不干胶 Adhesive Sticker导向针 Guide Din公差 Tolerance线切割 Wire-Cut电火花 Edm抛光 Polishing蚀纹 Texture探热针 Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板 Cover Plate齿轮 Gear油唧 Hydraulic Cylinder司筒 Ejector Sleeve导柱 Leader Pin冷料# Cold Slag线切割 Wire E.D.M.轮廓 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-Leader Pin镶件 Mold Insert锁定位 Lock楔子(铲鸡) Wedge高产量模量 High V olume Running Mold 剖面图 Cross Section模具结构Mold Construction 模芯 Parting Core局部视图Partial View热流道 Manifold热嘴 Hot Nozzle型腔数 Cav No模号 Mold No胶料 Material尺寸 Dimension重要尺寸Critical Dimension 雕刻 Engrave托司 EJ.GUIDE PIN。

模具专业词汇中英文对照表

die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模pound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点ining material to be inspected进货待验PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次production control confirmation生产确认checked by初审approved by核准stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明part number/ P/N 料号item/group/class类别prepared by制表year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料缺乏nick缺口speck瑕疵shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板〔顶板〕top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文pre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具〔移转成型用模具〕encapsulation molding低压封装成型〔射出成型用模具〕two plate两极式〔模具〕well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)〔成型机〕顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣各种模具常用成形方式accurate die casting 精细压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精细锻造cold forging 冷锻press forging 冲锻pacting molding 粉末压出成形rocking die forging 摇动锻造pound molding 复合成形rotary forging 回转锻造pression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡沫成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精细铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模posite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead X力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机c milling machine C铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床 NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板外表处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊外表austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光芒热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性emtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 外表蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 局部淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 外表硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking pound 填隙料cell 气孔cold slug 半凝式射出colorant 著色剂color matching 调色color masterbatch 色母料pound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 後固化premix 预混料purging 去除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑胶原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CAcellulose acetate butyrate 醋酸丁酸纤维素CAB posite material 复合材料cresol resin 甲酚树脂CF dially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPEmelamine resin 三聚氰胺酚醛树脂MFnitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PApolybutyleneterephthalate 聚对苯二甲酸丁酯PBTpolycarbonate 聚碳酸酯PCpolyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETPpolymetylmethacrylate 聚甲基丙烯酸甲酯PMMApolyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PPpolystyrene 聚苯乙烯PSpolytetrafluoroethylene 聚四氟乙烯PTFEpolytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PEpolyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PVACpolyvinylalcohol 聚乙烯醇PVApolyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVCpolyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 外表中部波皱check 细裂痕checking 龟裂chipping 修整外表缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕range peel 橘皮状外表缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲外表划伤seam 裂痕shock line 模口挤痕short shot 充填缺乏shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening 矫直streak 条状痕surface check 外表裂痕surface roughening 橘皮状表皮皱摺surging 波动torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具工作法用语adjustable spanner 活动扳手angle cutter 角铣刀arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具pass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳 plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工coining 压印加工pressing 压缩加工pression bending 押弯曲加工。

模具术语(中英文对照)

AD-Diameter Thetreaddiameteratthecenterlineofthetread(EU);also:"T-Diameter"(GT)?AD直径：指胎面中心线直径（EU）。

又叫T直径（GT）Auto-lockEar ALugontheconeringusedtomountthemold/containerinthetophalfofa60“NRMAuto-lo ckpress.??导环上的突缘，用于和60“NRMAuto-lock硫化机上半部连接。

BeadRing Thetirebeadformingring(also:toering)?钢圈，也称toeringBeadRingRegister??钢圈配合：侧板上，和钢圈配合的平面及锥面BottomContainerPlate?模壳底座BottomContainerPlateLiftingLugsedforlifting.???分离钩：就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。

BreakerHookGuidePiece Ablockboltedtothebreakerhookthatalignsthetreadsegmentwithaslotinthebottomcontainerplate. ??分离钩导块：用螺栓固定在BreakerHook上，定位花纹块和模壳底座上槽的定位块。

BronzeWearPlates Anysacrificialmetalplateplacedunder,overorbehindacomponenttokeeptheco mponentsfromwearingoneachother(greasing)?青铜耐磨板(油润滑的)Casting Anun-machinedcastmetaltreadringorSegment?铸件：未加工的金属花纹圈或花纹块铸件。

CenteringRing Theringmountedonthebottompressplatentolocatethemold/containerconcentrically tothepress;also:"Pressregister"??定中环,也称“Pressregister”ClampRings Thebladderclampingassembly??胶囊夹盘ConeRinglso:"Actuatorring","Squeezering"(GT)??导环，也称"Actuatorring","Squeezering"Conicity?锥度Container?模壳,也叫mechanismContainerCavity??rea??DEVAMetal??DEVADowelPins Thepinsthatkeepthemoldhalvesandpartsaligned(containersorHKKmolds)?定位销：用来对模具的半模或零件定位的销（模壳或HKK模具）。

模具中英文对照(整理)

工程部 / Design department:1) Designer - 设计师。

2) Assembly drawing - 模具组装图。

3) Mold layout - 模具结构图。

4) 2D product drawing - 2D产品图。

5) 3D product data - 3D产品数据。

6) Part drawing - 散件图。

7) Insert molding - 镶件模。

8) 2 color mold / Double injection tool - 双色模。

9) Hydraulic system - 油/水压系统。

10) Parting line - 分模线。

11) Air venting - 排气槽。

12) Cooling system - 冷却系统。

13) Screw - 镙丝。

14) Hot runner system - 热流道。

15) Valve gate - 伐针入水口。

16) Fan gate - 扇型入水口。

17) Pin point gate - 针点进胶。

18) Moon gate / Banana gate - 香蕉，象牙入水口。

19) Submarine gate - 潜水口。

20) Injection machine tonnage - 注塑机吨数。

21) Number of cavity - 穴数。

22) Steel - 钢材。

23) Copper - 铜。

24) Tungsten copper - 钨铜。

25) Beryllium copper - 铍铜。

26) Hardening - 加硬/淬火。

27) Tempering - 回火。

28) Chroming - 电镀。

29) Painting - 喷漆。

30) Resin - 胶材。

31) Printing - 丝印。

32) Texturing - 嗮纹/咬花。

33) Socket screw - 带肩镙丝。

模具常用语中英文对照

以下是30 个模具常用语的中英文对照：1.模具：mold2.模具设计：mold design3.模具制造：mold manufacturing4.模具加工：mold processing5.模具寿命：mold life6.模具维护：mold maintenance7.模具成本：mold cost8.模具材料：mold material9.模具结构：mold structure10.模具零件：mold part11.模具装配：mold assembly12.模具调试：mold debug13.模具成型：mold forming14.模具分型面：mold parting surface15.模具型腔：mold cavity16.模具型芯：mold core17.模具滑块：mold slider18.模具斜顶：mold lifter19.模具顶针：mold ejector pin20.模具冷却系统：mold cooling system21.模具浇注系统：mold gating system22.模具排气系统：mold venting system23.模具尺寸公差：mold dimensional tolerance24.模具表面粗糙度：mold surface roughness25.模具硬度：mold hardness26.模具钢：mold steel27.模具加工工艺：mold processing technology28.模具检测：mold inspection29.模具修改：mold modification30.模具报废：mold scrap。

模具术语中英文对照表

模具术语中英文对照表模具是制造行业中重要的零部件之一，不同的国家或地区对于模具的称呼和术语有着不同的表述。

下面是模具术语的中英文对照表，供大家参考。

一、模具结构及零部件1.凸模：punch/upper die2.凹模：die/lower die3.合页模：hinge die4.活动凸模：movable punch5.固定凸模：fixed punch6.活动凹模：movable die7.固定凹模：fixed die8.下座：bottom plate/bottom clamping plate9.定位销：locating pin10.定位套：locating sleeve/bushing11.导柱：guide pillar12.导套：guide bush13.顶杆：ejector rod/knockout rod14.顶针：ejector pin/knockout pin15.顶出板：ejector plate/knockout plate16.压簧：compression spring17.弹簧：tension spring18.滑块：slide block19.顶针板：ejector plate/knockout plate二、模具材料1.冷/热作模钢：cold/hot work die steel2.合金工具钢：alloy tool steel3.模具钢：mould steel4.不锈钢：stainless steel5.硬质合金：hard alloy/cemented carbide6.铝：aluminum7.铜：copper8.铜合金：copper alloy9.镁合金：magnesium alloy三、模具表面处理1.硬化：hardening2.淬火：quenching3.氮化：nitriding4.喷涂：spraying5.镀铬：chrome plating6.抛光：polishing7.喷砂：sandblasting四、模具制造工艺1.车削：turning2.铣削：milling3.磨削：grinding4.电火花加工：electric discharge machining (EDM)5.线割加工：wire-cut EDM6.钻孔：drilling7.铰孔：reaming8.螺纹加工：threading9.组装：assembly10.检验：inspection以上是模具术语的中英文对照表，本表可供参考，希望对有需要的读者有所帮助。

模具中英文对照

1.目的：为统一本厂冲压模具专业术语的中英文对照作业而制订本文件。

2.范围：适用于本公司各部门之作业。

3.职责：各部人员根据本节内容来进行相关作业。

4.内容：4.1.1 模具相关术语对照表：spotting['spɑtɪŋ] 合模种类中文名称英文名称中文名称英文名称模具种类连续模Progressive die 冲孔模Pierce die 机械手Transfer die 剪边模Trimming die 手动机械手Hand transfer die 下料模Blanking die 单工程模Single die 成形模Forming die 铸造结构模Cast die 折弯模Bending die 简易模Prototype die 围边模Flange die 铆合模Riveting die 拉伸模Draw die 复合模Compound die 快换模Changeable die工序类料带strip 料带图strip layout 工序process 冲导正孔pilot pierce 冲孔pierce 侧冲cam pierce 切边notch 切侧刃notch french 折弯bend 墩薄coin成形form 侧成形cam form 整形restrike 围边flange打凸米boss / dimple 打凸包emboss打字印stamp 打沙拉孔hourglass 面押coin burr 抽孔extrude hole 拍平flat 卷圆curl种类中文名称英文名称中文名称英文名称工序类旋转rotate 铆接rivet产品切边线trim line 铆螺母stake nut 切断cutoff 接刀口mismatch 料带带料处carrier tab 毛刺方向burr direction压线groove 下料blanking模板类上托板top plate 下托板bottom plate 上垫脚upper parallel 下垫脚lower parallel 上模座upper die set 下模座lower die set 上垫板punch backup 下垫板lower backup 上夹板punch holder 下夹板die holder 上脱料板stripper 下模板die plate 冲头punch 凹模die零件类浮块lifter 浮料板lifter plate 成型公form punch 压料块pressure pad 切边冲头trim punch 刀口trim steel 沉头孔counter bore 冲孔入子button 顶针kick off / ejector 废料切断刀slug breaker 成型凹模forming die 整形公restrike punch 导尺rail 导尺顶杆lifter bolt 导料板rail plate 镶件/入子insert侧冲组件cam 滑块slide滑块上油槽oil groove 铲机driver码模槽mounting slot 储运块storage block 限位柱stop block 起吊孔handing hole 起吊环eyebolt 靠块heel脱料板拉杆spool 模座导正块thrust heel 中文名称英文名称中文名称英文名称种类零件类耐磨片wear plate 垫片shim 压块keeper 初始管位first start pin 键槽key slot 键key氮气弹簧nitrogen spring 螺旋弹簧coil spring 聚氨酯弹簧urethane 导柱guide post 导套guide bushing 插针pilot pin 插针套pilot bushing 侧刃french 传感器sensor 销dowel 螺丝screw 拔牙jackscrew垫圈washer 盲销blind dowel压毛边冲头deburring punch 挡块stopping plate压线冲头groove punch 定位块location block字模冲头stamp punch 圆冲头round punch压筋冲头ribbon punch 气垫板air cushion plate 异形冲头special shape punch 气垫顶杆air-cushion eject-rod 切边冲头trimming punch 上压块pressure block加强筋冲头stiffening rib punch 弹簧箱spring box 定位板guide plate 弹簧箱顶杆spring-box eject-rod 压边圈binder 弹簧箱顶板spring-box eject-plate公差类公差tolerance 公差范围tolerance range 上公差upper tolerance 下公差lower tolerance 公差+/- 0.05 plus minus 0.05 形位公差图GD&T 平面度flatness 直线度straightness 倾斜度angularity 垂直度perpendicularity 平行度parallelism 圆度roundness种类中文名称英文名称中文名称英文名称公差类圆柱度cylindricity 面轮廓度surface profile 线轮廓度line profile 位置度true position 同轴度concentricity 对称度symmetry 圆跳动runout 全跳动total runout 尺寸dimension 角度值angle degree 尺寸全检报告dimensional layout 三次元尺寸报告CMM report冲床相关机械冲床mechanical press 油压机hydraulic press 吨位tonnage 行程stroke / travel 冲床上台面ram 冲床下台面bolster冲床台面布置图press layout 冲床上的快速对正QDC 冲床气垫air cushion 码仔stirrup 闭合高度shut height T型槽T-slot送料机feeder 送料高度feeding height工卡尺caliper 千分尺micrometer 直尺ruler 高度尺height gage具丝攻screw tap 起子screwdriver 拨牙器jacker 扳手wrench风磨机hand grinder 油石oil stone加工类开料cutting material 钻drill (DR) 攻牙tap 铰ream铣mill 车lathe电脑锣NC mill 线切割wire cutting(W/C) 磨grind 刨planer电火花EDM 镭射laser cutting 倒角chamfer xx的精加工finish XX真空热处理vacuum heattreatment镀钛TD coating 退磁demagnetization 烧焊weld4.1.2 加工说明对照表：加工说明Machining Note注:有0.00的地方为数据填入处X:-￠0.00（氮气弹弓过孔，锣穿）单+0.00X:-￠0.00 (DR.THRU FOR GAS SPRING) S+0.00X:-￠0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:-￠0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00) X:-￠0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:-￠0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00) X:-￠0.00（合销孔,铰)X:-￠0.00 (REAM FOR DOWEL)X:-￠0.00（合销孔,割)单+0.00X:-￠0.00 (W/C FOR DOWEL) S+0.00(正面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)(反面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（合销孔,钻穿)X:-￠0.00 (DR.THRU FOR DOWEL)X:-￠0.00（一般孔,钻穿)X:-￠0.00 (DR.THRU HL)X:-￠0.00（穿丝孔,钻穿)X:-￠0.00 (DR.THRU FOR WEDM S.H.)X:-￠0.00（漏油孔,钻穿)X:-￠0.00 (DR.THRU FOR DRAIN HL)X:-（漏油槽,反面CNC单+0.00,锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:-￠0.00（基准孔,铰)X:-￠0.00 (REAM FOR DATUM HL)X:-￠0.00钻穿（螺丝过孔)内攻M0.00牙X:-￠0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR)(正面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE)(反面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)(侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)X:-M0.00钻穿,正面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00钻穿,正反面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 OPP. SIDE, THR DP0.00)X:-M0.00盲孔,正面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00盲孔,正反面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,侧面分中攻深0.00,组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT) (侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00钻穿（拨牙螺丝孔，攻穿）X:-M0.00 DR.THRU FOR JACK SCREW, TAP THRUX:-￠0.00（塞打过孔,钻穿)X:-￠0.00 DR.THRU FOR SPOOLX:-￠0.00（弹弓过孔,钻穿)X:-￠0.00 DR.THRU FOR SPRINGX:-￠0.00（弹弓孔,反面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 OPP.SIDE, USED DP.0.00)X:-￠0.00（弹弓孔,正面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00)X:-（避空孔,锣穿)单+0.00X:- (POCKET THRU)S+0.00X:-（避空孔,正面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-（避空孔,反面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-￠0.00（避空孔,反面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE)X:-￠0.00（避空孔,正面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE)X:-￠0.00（两用销过孔,割)单+0.00X:-￠0.00 (LIFTER PIN, W/C S+0.00)X:-（导尺避空,CNC单+0.00锣穿)X:- (POCKET FOR RAIL, CNC MILL THRU, S+0.00)X:-（导尺避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（导尺避空,反面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 OPP. SIDE, S+0.00) X:-（浮块避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR LIFTER, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（浮块孔,割）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, W/C)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-（浮块孔,锣）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, MILL)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-￠0.00（顶针孔,钻穿)（反面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（顶针孔,钻穿)（正面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)X:-￠0.00（导柱（导套）孔,CNC锣)单+0.00X:-￠0.00 CNC MILL FOR GUIDE PIN(BUSHING) S+0.00X:-￠0.00（导柱（导套）孔,割)单+0.00X:-￠0.00 W/C FOR GUIDE PIN(BUSHING) S+0.00X:-M0.00*1.5(止付螺丝，正面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 TOP SIDE)X:-M0.00*1.5(止付螺丝，反面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 OPP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:-（INSERT HL, CNC MILL THRU S+0.00)(阴影部分正面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 TOP SIDE)(阴影部分反面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 OPP SIDE)X:-（入子孔,割）单+0.00X:-（INSERT HL, W/C S+0.00)(阴影部分扣位正面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 TOP SIDE)(阴影部分扣位反面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 OPP. SIDE)(正面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)注: 此处的沉头不能用C'BORE, 只有圆形的沉头才用C'BORE.(反面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:- (INSERT HL, CNC MILL THRU. S+0.00)X:-（入子孔,正面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 TOP SIDE)X:-（入子孔,反面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 OPP. SIDE)X:-￠0.00（插针孔,铰)单+0.00X:-￠0.00（REAM S+0.00 FOR PILOT PIN)X:-￠0.00（插针孔,割)单+0.00(正面沉头￠0.00*0.00深)X:-￠0.00（W/C S+0.00 FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-￠0.00（插针孔,钻穿)(正面沉头￠0.00*0.00深)X:-￠0.00（DR.THRU S+0.00 FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-（冲头过孔,割)单+0.00(正面避空，CNC单+0.00，锣深0.00)(阴影部分扣位正面锣深0.00)X:-（W/C S+0.00 FOR PUNCH CLEARANCE HL)(POCKET, CNC DP 0.00 S+0.00 TOP SIDE)(POCKET SHADE FOR HEAD, DP0.00 TOP SIDE)X:-（冲头过孔,锣穿)单+0.00(正面避空，CNC单+0.00，锣深0.00)X:-（MILL THRU. S+0.00 FOR PUNCH CLEARANCE HL) (POCKET DP0.00 CNC S+ TOP SIDE)X:-（异形冲孔,直x斜x,割)单+0.00(双线部分，割)单+0.00X:-（W/C FOR SPECIAL HL, 0.00 LAND 0.00 TAPER, S+0.00) (W/C PER DOUBLE LINE S+0.00)X:-（冲孔,直x斜x,割)单+0.00X:-（W/C FOR PIERCE DIE HL, 0.00 LAND 0.00 TAPER S+0.00) X:-（冲孔,割)单+0.00X:-（W/C FOR PIERCE DIE HL S+0.00)X:-￠0.00（冲孔漏屎,钻穿)X:-￠0.00 (DR. THRU FOR CHUTE)X:-（异形冲孔漏屎,CNC单+0.00,锣穿）X:-￠0.00 (MILL. THRU FOR SPECIAL CHUTE S+0.00)X:-（产品落料斜度，实数斜30º锣）X:-（MILL 30 TAPER FOR PART RAMP NO CLEARANCE)X:-（漏屎斜度，直x斜45º锣）X:-（MILL FOR CHUTE 0.00 LAND 45 TAPER)。

各式模具分类用语中英文对照

loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offset bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模portable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模run less injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具cassette 卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 电脑copy 复制cursor 游标curve modeling 曲面模拟database 资料库design 设计digitizing 数位化disk 磁碟dot 点eyelet 眼孔floppy 磁碟片format 格式化graphic 圆解hardware 硬体honeycomb 蜂巢interface 界面know how 秘诀laser printer 雷射印表机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling 造型module 模组monitor 萤幕mouse 滑鼠need 需求network 网路new version 新版on line 上线中option 选择PC 个人电脑Plotter 绘图机Program 程式scanning 扫描simulation 模拟software 软体solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工coining 压印加工compressing 压缩加工compression bending 压弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 摺叠加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工slitting 割缝加工stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 後角corner shear drop 直角压陷deflection 挠曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼後熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件模具加工方法barrel 滚筒(加工)bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验austenitic steel 沃斯田铁钢Brinell hardness 布耐内尔硬度Brinell hardness test 布氏硬度试验Charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test境应力龟裂试验Ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体Gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验Izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验Martensite 马氏体Mullen bursting strength tester密廉式破裂强度试验机Nol ring test 诺尔环试验normal distribution 常态分配ozone resistance test 抗臭氧试验Pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验Rockweel hardness test 洛氏硬度试验Rockweel hardness 洛氏威尔硬度Rolinx process 罗林克斯射出压缩成形法Rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shore hardness 萧氏硬度spiral flow test 螺旋流动试验surface abrasion test 表面磨耗试验Taber Abraser 泰伯磨耗试验机tensile impact test 拉伸冲击试验tensile strength 抗拉强度tension test 张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验Ubbelohde viscometer 乌别洛德黏度计Vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验weatherometer 人工老化试验机Weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮Al2O3 氧化铝balance 平衡bond 结合borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘mesh 网筛目parameter 参数resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转机械设计及周边其他用语assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重覆载荷sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割业务与贸易关连用语accept order 接受订货account 帐户after service 售后服务amendment 修正annual sales 年销售额at sight 见票即付balance 余额bank draft 汇票bargain goods 廉价品batch 批次bid 出价bid sales 投标买卖bill of landing 提单bills receivable 应收票据brand 品牌bulk cargo 散装货business transaction 商业交易buyer 买方carbon copy 打字副本cargo collection 揽货carton 纸箱cash in advance 预付现金catalogue 型录cheque 支票CLF 运费保险费在内价格claim 索赔clearance goods 清仓品commision 佣金commission 批发商complain 抱怨container 货柜correspondence bank 往来银行cost 成本cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单D/P 付款交单deferred payment 分期付款deferred shipment 分期装运delivery on spot 当场交货delivery time 交期delivery order 交货单discount 折扣discount on draft 贴现documentary draft 跟单汇票down payment 订金enclosure 附件endorsement 背书exhibition 展览会export 出口factory visit 工厂参观favourable price 合宜价格foreign exchange 外汇free on board 船上交货价idea price 希望价格import 进口Japanese Industrial 日本工业规格invoice 发票L/C 信用状margin 利润market 市价net weight 净重no payment 拒绝付款odd item 零头offer 报价open account 交互计算order 订单over looked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格payment method 付款方式port of destination 目地港port of trans-shipment 转口港price 价格price descending 减价price rising 涨价procurement 采办prompt delivery 即时交货purchase 购入purchasing agent 采购代理商quotation 报价单rebate 回扣reference 查询remittance 汇款repeat order 追加订货request letter 请求函rumor 风评second hand goods 二手货shipper 货主shipping 装船shipping mark 麦头shipment 出货sold out 卖完sole agent 总代理商special discount 特别折扣specification 规格sample order 指样订货standing 信用情形storage charge 仓租subcontract 外包subject to final confirmation 有待确认之报价supplier 供应商T/T 电汇tie-in sale 搭售trade fair 商展会trans-shipment 转运transferred 已转运wharf 码头A 3D coordinate measurement 三次元量床3D modeling 三次元模拟aberration 色差abnormal glow 不规则辉光放电abrasive 砂轮access 通路account 帐户accretion 炉瘤accurate die casting 精密压铸acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth activator 活化剂acetylene 乙炔adjustable spanner 活动扳手aerator 松砂机ageing 老化处理air hardening 气体硬化airless plasting cleaning 离心喷光air patenting 空气韧化air permeability test 透气性试验air set mold 常温自硬铸模air vent valve 通气阀all core molding 集合式铸模alloy tool steel 合金工具钢allround die holder 通用模型aluminium alloy 铝合金钢amendment 修正ampere 电流安培anchor pin 锚梢angle cutter 角铣刀angle welding 角焊angular pin 角梢breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 著色剂color matching 调色compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 後固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑胶原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树CF dially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme醋酸乙烯共聚物EVA expanded polystyrene 发泡聚苯乙烯EPSfiber reinforcement 纤维强化复合材料high density polyethylene 高密度聚乙烯HDPE high impact polystyrene 高冲击聚苯乙烯HIPS high impact polystyrene rigidity高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAP 耐龙PA 聚对苯二甲酸丁酯PBT 聚碳酸酯PC 聚乙二醇PFG 聚氧化乙烯PEO 聚乙醇对苯PETP 聚甲基丙烯酸甲酯PMMA 聚缩醛POM 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO 聚丙烯PP 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差atomization 雾化bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕hair crack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱摺surging 波动sweat out 冒汗torsion 扭曲]warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹。

模具用语中英文对照表

locking block
弹性体
高分子物质原料，在常温下具橡胶弹性的固体。
elastomer
可塑剂
提高树脂的可塑性，同时给与制品柔软而加于树脂的液状或固体的物质，分为一次可塑性及二次可塑性，又将高分子
量的可塑性，特称为高分子可塑剂。
plasticity
可塑性
在弹性限度以上的应力下变形之后，除去应力也不会恢复原形的性质叫可塑性。
（3）指转注成形模具浇口的平坦部份。
land
横浇道
射出成形模具或转注成形模具里，把溶化材料注入模窝的通道中，（）浇口到进浇口的部份，
亦指在这里硬化的材料，亦有为经常保持横浇道内部的材料熔解，研究出热横浇道模具、横浇道断热模具等。
runner
料头打扳
3片模的去除横浇道固化料用的扳子。（自动去除）。
runner stripper plate
可铸树脂
注入于开口模型中，不需加压就可硬化，可加热就呈注液状的树脂。
casting resin
透明性
可透穿可视光线的性质。依透穿和程度还有半透明性（translucency）及不透明性（opacity）。
transparency
流动
材料的塑性变形，一般称为流动，这里所提的是成形时的流动性。
flow
粘度
无料头模具
直接把熔化材料喷嘴射进模窝，或者将（）浇口横浇道加热，经常保持塑料熔解，只取出固化形品的连续高速模具。
runnerless mo(u)ld
料头扣针
当闭模时确实地把料头去除而设在模具内有嵌口的梢子。
runner lock pin
承扳
（基扳）
成形模具中嵌入母模，公模道杆等的基扳，亦可直接雕模窝。

模具术语中英文对照【大全】

上模：Upper Die上模座：Upper die holder下模：Lower die下模座：Lower die bottom环模：Holder die压料板：Pad安全护板：Safety Guard耐磨板：Wearplate吊耳：Hook插入式吊耳：Insert hook搬运固定板：Fix in Plates防呆装置：Fool Proofing快速定位：Quick Clamp安全侧销：Retainer pin sets(Safety) 保管垫块：Blocks平衡垫块：Balancer block停止垫块：Stoper block氮气缸：NiirogenSpring到底记号：Check Buttons镶块：Insert Block素材定位器：Nest Guide进退料支架：SKID Brackets脱料板：Stripper die顶料块：lift block零件详细：Parts detail检具：Checking Fixture气缸：Cylinder接头：Adapter(Augmture)快速接头：Quick Nipple三向接头：Three-Way Connector万向接头：Universal-Joint adapterL型快速接头：L JointT型快速接头：T Joint阀：Valve调速阀：Covernor Valve方向调节阀：Directional Control Valve 定位销：Location Pin开口销：Split Pin带头销：Pin with head固定销：Doweel Pin夹：Clamp管：Pipe连接管：Connector排气孔：Air Vent轴：Shaft连杆轴：Link shaft下模钢块：Lower Steel行程定位：Stroke end block 废料刀：Scrap cutter废料盒：Scrap Box定位键：locating key凸轮组件：Cam Unit凸轮滑动座：Cam Slide凸轮驱动座：Cam driver凸轮侧滑块：Cam side slide 切刀块：Cutter Nlock分块：Sectional Block导柱：Guide Post导套：Guide bush导柱组：Guide Post Set缓冲垫块：Cushion Plate挡板(块)：Baffle垫块：Plate垫圈：Washer焊接：Welding树脂：Resin消音器：Muffle螺帽：Nut有槽螺帽：Slotted Nut销规：Guage承盘：Retainer柱塞：Plunger端子箱：Cable connecting Box集头座：Connector Support内六角螺栓：SHC Screw内螺纹圆柱销：DOWEL PIN吊挂：Retainer Bolt弹簧导销：Spring Guide retainers 工法图：Die layout上模面：Upper die of plan view 下模面：Lower die of plan view 断面：Section冲头：Punch固定块：Fix Plate作用套管：Spool Retainer滚轮：Rubber roller衬套：Bushing冲头固定座：Retainer 盖板：Safety Guard托架：Bracket曲柄：Crank。