工业除湿机说明书新

合集下载

wetking湿王工业除湿机说明书

wetking湿王工业除湿机说明书

wetking湿王工业除湿机说明书一、设备概述wetking湿王工业专为喷浆聚合尿素复合肥等装置除湿而设计,是目前最新型的冷却干燥设备。

该除湿机是采用冷冻除湿原理,对冷却空气进行除水降温的一种空气干燥冷却设备。

它是经实际运行改进后第四代产品,因采用先进技术和高质量的进口元件,具有性能可靠、运行平稳、噪音低、耗能少、安装不需要基础等优点,为喷浆聚合尿素复合肥装置除湿干燥的首选产品。

二、除湿机工作原理wetking系列冷冻除湿机是根据冷冻除湿原理,对空气进行除湿的设备。

它利用压缩制冷系统,对进入除湿机的空气进行强制冷却,使其中含有大量的水汽凝成液滴,经专用气液分离器分离后排出,其成品气露点可达5-10C.其工作过程:高温高湿的空气首先进入预冷器、用出口冷空气来冷却,使进气冷却到27"C左右,除去约20%左右的水分,被预冷后的湿空气再进入蒸发器进入强制冷却,使湿空气温度降至1-7"C左右,通过专用分离器除去约60%左右的水分,此时空气中的含水量已很少,约7g/m3左右。

除湿后的空气经热交换器和加热器升温后,温度约20"C左右,相对湿度≤55%,成为干燥成品气。

在极限工况下整个除湿过程可除去约80%左右的水分。

三、露点温度的自动调节说明由露点温度的高低自动控制压缩机的加、减载,使设备控制在最佳制冷量状态下。

1.温度设定范围: 2~25'C2.温度偏差设定范围: 1~3C3.当露点温度到达设定温度的上偏差时,压缩机加载时间设定范围0.5~2秒,稳定时间设定范围10~90秒,若出风温度还在上偏差时,再次加载0.5~2 秒,稳定10-~90秒,依次累推直到露点温度回到偏差范围内为止。

4.当露点温度到达设定温度的下偏差时,压缩机减载0.5~2秒,稳定10~90秒,若出风温度还在下偏差时,再次减载0.2~2秒,稳定10~-90 秒,依次累推直到露点温.度回到偏差范围内为止。

CD425工业除湿机安装、操作和维护手册说明书

CD425工业除湿机安装、操作和维护手册说明书

CD425 INDUSTRIAL DEHUMIDIFIER INSTALLATION, OPERATION & MAINTENANCE MANUALCD425 1018125PACKAGE CONTENTSItem Description Quantity 1018125 Dehumidifier 1 3086144 Quick release hose coupling 1 3944110 PVC Tube – 3/8” I/D 7.8M TPC250 Manual 1CD425 1018150PACKAGE CONTENTSItem Description Quantity 1018150 Dehumidifier 1 3086119 Jubilee clip 2 3017315 Reinforced tubing – 16mm I/D 2 X 3M TPC250 Manual 1UNPACKINGCarefully remove the CD425 dehumidifier unit from its transit box and visually check for signs of transit damage. If there is evidence of damage DO NOT attempt to operate the unit, call your supplier for advice. Do not discard the packing; it will be useful when transporting the dehumidifier unit in the future.INTRODUCTIONThe Ebac CD425 dehumidifier removes moisture from the air that circulates through it. The resulting reduction in relative humidity protects buildings and their contents from the adverse effects of excess humidity.The CD425 dehumidifier comprises of:a) A compressorb)Refrigerant evaporator coilsc)Refrigerant condenser coilsd)Circulation fane) A drain tray for collecting and disposing of condensed moisturef) A cabinet to house the above componentsThe fan draws the moist air through the cold evaporator coils which cools the air below its dew point. Moisture forms on the evaporator and is collected in the condensate tray which leads away to a permanent drain. The cooled air then passes through the hot condenser, where it is reheated using the same energy removed during the cooling phase and the additional heat generated by the compressor.The air is, therefore, discharged from the dehumidifier at a slightly higher temperature, but a lower relative humidity, than that which it entered. Continuous circulation of air through the dehumidifier gradually reduces the relative humidity within the area being dehumidified.Where large amounts of moisture are required to be removed from the area, more than one dehumidifier may be required, please contact your local distributor for advice.SPECIFICATIONS"This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Therefrigeration system is hermetically sealed.The Global Warming Potential (GWP) of refrigerants used in products manufactured by EbacIndustrial Products Ltd is as followsR134a – 1300R407c – 1610For type and weight of refrigerant contained in this unit, please refer to the product data label"M ODEL: CD425H EIGHT: 1193 mm (47”)W IDTH: 1092 mm (43”)D EPTH: 482 mm (19”)W EIGHT: 160 Kg (353 lbs)A IRFLOW: 2975 m3/hr (1750 cfm)M AXIMUM O PERATINGT EMPERATURE: 35ºC (95ºF)P OWER S UPPLY: 440V, 3 ph, 60HzR EFRIGERANT T YPE/Q TY: R407c (2.5Kg)OPERATIONThe CD425 is a self contained low temperature dehumidifier. All electrical contactors, overloads, etc are housed in an electrical box built inside the unit. The unit is quipped with a defrost valve which energised automatically to clear any ice formation on the evaporator coils. This allows the unit to operate at much lower temperatures, the control panel gives indication of the set humidity, drying and defrost status.TEST FOR CORRECT OPERATIONThe following procedure should be followed to test the unit for correct operation.1) After unpacking connect the unit to a 460V 3ph 60 Hz – 3 wire powersupply.2) Switch fan ON and check for the correct fan rotation. (Air blows out of thetop of the machine).3) Check dehumidification process:a) Remove the front coverb) Check the actual relative humidity inside the areac) Set humidity control to a LOWER value than the actual relativehumidityd) After approximately 6 minutes check the compressor is runninge) Leave the machine to run for 15 minutes. (NOTE: ensure thatthe set humidity, see c above, is set very low as the compressorwill switch off when the actual RH coincides with the set point)f) Observe the evaporator coilsi. If the air temperature is below 20ºC an even coating ofice should cover the entire evaporator coilii. If the temperature is above 20ºC droplets of condensedwater should cover the entire evaporator coil4) If the air temperature is below 20 ºC the unit will go into defrost within60 minutes. During the defrost cycle the defrost solenoid valve isenergised and a warming of the evaporator coil can be felt.If after carrying out the above checks the unit does not appear tofunction correctly refer to the repairs section or your supplier.SYSTEM INSTALLATIONPOSITIONING:Position the CD425 in the area leaving enough room at either end of the unit to allow for easy servicing. Using a spirit level ensure the level in both directions. Failure to do so may result in the drain tray overflowing and flooding of the chamber.WIRING:Connect a suitable 3 phase mains power supply to the MAINS T/B terminal block inside the electric box located at the control panel end of the machine. DRAINAGE:Connect the outlet from the drain tray (located behind the front grille and under the evaporator coils) to a permanent drain.Please ensure that the drainage does not rise above the level of the CD425’s drain tray. Failure to observe this requirement will result in internal flooding of the dehumidifier.ROUTINE MAINTENANCETo ensure continued full efficiency of the dehumidifier, maintenance procedures should be performed as follows:1. Clean the surface of the evaporator and condenser coils by blowingthe dirt out from behind the fins with compressed air. Hold the nozzle of the air hose away from the coil (approx 6”) to avoid damaging the fins. Alternatively, vacuum clean the coils.2. Check that the fan is firmly secured to the motor shaft and that thefan rotates freely. The fan motor is sealed for life and therefore does not need oiling.3. To check the refrigerant charge, run the unit for 15 minutes andbriefly remove the cover. The evaporator coil should be evenly frost coated across its surface. At temperatures above 25°C, the coil may be covered with droplets of water rather than frost. Partial frosting accompanied by frosting of the thin capillary tubes, indicates loss of refrigerant gas or low charge.4. Check all wiring connections.5. To check the operation of the defrost system, ensure the airtemperature is below 20°C, switch the machine on and leave it running for approximately 1 hour. The machine will then enter “Hot Gas” defrost mode for approximately 5 minutes before returning to normal operation. If the unit will not defrost, the printed circuit timer board/sensor may be defective or the by-pass valve may be inoperable.I F ANY OF THE PRECEDING PROBLEMS OCCUR , CONTACT THE E BAC S ERVICE C ENTER PRIOR TO CONTINUED OPERATION OF THE UNIT TOPREVENT PERMANENT DAMAGE .WARNING:ENSURE THAT THE POWER CORD TO THE MACHINE HAS BEEN DISCONNECTED BEFORE CARRYING OUT ROUTINEMAINTENACE ON ITEMS 1, 2, 3, 4, AND 5.WARNING: DO NOT STEAM CLEAN REFRIGERATION COILSREPAIRS1. Should an electrical component fail, consult the Factory ServiceCenter to obtain the proper replacement part.2. If refrigerant gas is lost from the machine, it will be necessary to usea refrigeration technician to correct the fault. Contact the FactoryService Center prior to initiating this action.Any competent refrigeration technician will be able to service the equipment. The following procedure must be used:a. The source of the leak must be determined and corrected.b. The machine should be thoroughly evacuated beforerecharging.c. The unit must be recharged with refrigerant measuredaccurately by weight.d. For evacuation and recharging of the machine, use the crimpedand brazed charging stub attached to the side of the refrigerantcompressor.The charging stub should be crimped and rebrazed afterservicing. N EVER allow permanent service valves to be fitted toany part of the circuit. Service valves may leak causing furtherloss of refrigerant gas.3. The refrigerant compressor fitted to the dehumidifier is a durableunit that should give many years of service. Compressor failure can result from the machine losing its refrigerant gas. The compressor can be replaced by a competent refrigeration technician.Failure of the compressor can be confirmed by the following procedure:a. Establish that power is present at the compressor terminalsusing a voltmeter.b. With the power disconnected, check the continuity of the internalwinding by using meter across the compressor terminals. Anopen circuit indicates that the compressor should be replaced.c. Check that the compressor is not grounded by establishing thata circuit does not exist between the compressor terminals andthe shell of the compressor.TROUBLESHOOTINGS YMPTOM C AUSE R EMEDYUnit inoperative 1. No power to unit 1. Check the power supplyLittle or no airflow 1. Loose fan on shaft2. Fan motor burnt out3. Dirty refrigeration coils4. Loose electrical wiring1. Tighten fan2. Replace the fan motor3. See Routine MaintenanceSection4. Check the wiring diagramto find fault and repairLittle or no water extraction 1. Insufficient air movement2. Compressor fault3. Loss of refrigerant gas4. Blocked filter dryer1. Check all of the above2. Contact the FactoryService Center3. Contact the FactoryService Center4. ReplaceUnit vibrates excessively 1. Loose compressormounts2. Damaged fan1. Tighten the nuts on thecompressor mounts2. Replace with a new fanWater flooding 1. Drain pipe blocked/frozen2. Drain pipe too high1. Clear the obstruction2. No section of the drainagepipeCD425SPARE PARTS LISTD ESCRIPTIONP ART N UMBERQ UANTITYCompressor 3022144 1 Condenser Coil 3020725 1 Evaporator Coil 3020733 3 Defrost Valve 3020803 1 Reversible Filter Dryer 3020930 1Capillary Tube3014251 12X1400mmX0.047 R407c Freon Refrigerant 3100453 2.5kg Drain Tube 2014315 3 meters 3/8” Copper Tube 3014203 2 meters 1/2” Copper Tube 3014204 2 meters 5/8” Copper Tube 3014205 2 meters Cork Tape 3100223 1/2 Roll Fan Motor 3030140 1 Axial Fan 3010119 1 Solenoid Coil 3030402 1 Humidistat 1132200 1 Momentary Switch 3030634 1 Indicator Lamp Holder 3034513 2 12V 100ma Lamp30345224Spare parts available onlineHumidistat Control Knob2017707 1 Contactor 037H0021 3030355 1 Contactor 037H0041 3030362 1 Relay 3030270 1 Overload 3032646 1 Transformer 3031129 1 Timer 1919400 1 Transformer 3031173 1 Water Pump31601301LIMITED WARRANTYOur products carry a one-year unconditional warranty against any defects in workmanship or material. This warranty will cover all parts and labour required to repair your Ebac product. This warranty is invalid if the unit hasbeen abused, damaged, whether intentional or accidental, or if any modifications have been made to the unit.THE FOREGOING WARRANTY IS EXCLUSIVE AND IS ISSUED IN LIEU OFALL OTHER WARRANTIES (WHETHER WRITTEN, ORAL, OR IMPLIED) INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. EBAC INDUSTRIAL PRODUCTS, INC. DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL DAMAGES, LOST PROFITS, OR INCIDENTAL DAMAGES FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTYWITH RESPECT TO THE FOREGOING DESCRIBED MERCHANDISE.For Your Records: Model:____________________S/N:______________________Date Received:______________SAVE THIS SECTION FOR YOUR RECORDSCLIP AND RETURN THIS CARDPLEASE NOTE WARRANTY REGISTRATIONTo ensure that your Ebac Dehumidifier is accorded the full coverage provided by this warranty, please complete and mail this card at your earliest convenience. Thank You DATEMODEL ___________ S/N ________________ RECEIVED ________________ OWNER __________________________________________________________ ADDRESS ________________________________________________________ CITY __________________________ STATE ________ ZIP _______________ COMMENTS ______________________________________________________ _________________________________________________________________Ebac Industrial Products.700 Thimble Shoals Boulevard, Suite 109, Newport News, Virginia. 23606-2575UK Head Office Ebac Industrial Products Ltd St Helens Trading EstateBishop AucklandCounty DurhamDL14 9ADTel: +44 (0) 1388 664400 Fax: +44 (0) 1388 662590*************.ukAmerican Sales OfficeEbac Industrial Products Inc700 Thimble Shoals Blvd.Suite 109, Newport NewsVirginia, 23606-2575USATel: +01 757 873 6800Fax: +01 757 873 3632*****************German Sales OfficeEbac Industrial Products LtdMiraustra 64 – 6613509BerlinGermanyTel: +49 3043 557241Fax: +49 3043 557240www.eip-ltd.de****************。

除湿机设备操作说明书

除湿机设备操作说明书

設備操作說明書 第1页共1页 設備名稱
除濕機 設備功能 除濕 文件編號 設備型號 DH-81500 廠商 版次 A0 核准 審核 製作 日期 一﹑面板介紹﹕
1.操作面板
2.機箱
3.儲水箱門
4.顯示面板
5. 溫濕度設置鍵
6.溫/濕度轉換鍵
7.高/低速設置
8.電源開關鍵 二﹑操作﹕
1. 設備接通電源220V ﹐顯示面之各指示燈工作。

2. 按下“開關”鍵﹐設備通電工作。

3. 根據濕度要求﹐按下“設定”鍵設置濕度值。

4. 按下“風速”鍵﹐可設置設備風機高﹑/低速運轉。

5. 按下“℃/%轉換”鍵﹐可轉換溫度和濕度顯示。

6. 設置完成后﹐設備即可正常運行。

三﹑注意事項﹕
1. 保証設備表面清潔。

2. 每天將設備除濕機之水倒掉并清潔。

3. 設備四面需與牆壁隔離10~20CM ﹐以確保設備散熱。

4. 每周對設備進氣口過濾網清潔﹐保証設備除濕效果。

1 5 6
2 4
3 7 8。

PD161D 除湿机使用说明书

PD161D 除湿机使用说明书

PD161DImportant Safety Instructions11.Parts Description 2.3Operation 3.4Care & Cleaning 4.9Troubleshooting 5.10Warranty 7.12Warning 8.12Contact Us 9.12TABLE OF CONTENTSTechnical Specifications 6.11BEFORE FIRST USE:To prevent any internal damage, it is very important to keep refrigeration units (like this one) upright throughout their journey. Please leave it standing upright and outside the box for 24 HOURS before plugging it in.1. Make sure to turn off and unplug the dehumidifier before cleaning.2. Do not touch the plug with wet hands.3. Do not operate or turn off the dehumidifier by plugging in or unplugging thedevice. Use the control panel instead.4. Be sure to run the water hose sloping downward to let the water flow outsmoothly.5. Do not use if the power cord is broken or damaged.6. Do not place the dehumidifier in places where it may be splashed by water.7. Do not place the dehumidifier near a heat source.8. Do not install the dehumidifier in a location that may be exposed tocombustible gas.9. Do not use the dehumidifier near flammable gas or combustibles, such asgasoline, benzene, thinner, etc.10. Do not use in areas where chemicals are handled.11. Do not climb on or place objects on the dehumidifier.12. Do not place a heavy object on the power cord and make sure that thecord is not compressed.13.Place the dehumidifier on a level, sturdy section of the floor, and avoidplacing on uneven or tilted section. If the dehumidifier is knocked over during use, turn off the dehumidifier and unplug it from the main power supply immediately. Visually inspect the dehumidifier to ensure there is no damage.14. Disconnect the power if strange sounds, smell, or smoke comes from thedehumidifier.15. Do not take the water bucket out while the dehumidifier is working.16. Do not cover the intake or exhaust openings with cloths or towels.17. Care should be taken when using the dehumidifier in a room with thefollowing persons: infants, children, the elderly and people not sensitive to humidity.18. Never insert your finger or other foreign objects into grills or op.enings.Take special care to warn children of these dangers.19. You should never try to take apart or repair the dehumidifier by yourself.To preventing the user or other people's property damage injury, we must use the dehumidifier follow the instruction. Incorrect operation due to ignoring of instructions may cause harm or injury. This instructions is for household use only.20. Do not drink or use the water drained from the dehumidifier.21. Always insert the filters securely. Make sure to clean the filter once every month.22. Do not use the dehumidifier in tiny spaces.23. If water enters the dehumidifier, please turn the dehumidifier off and disconnectthepower,contactYaufeyCustomerServiceatemail:********************order to avoid a hazard.mo re th an 7.9in (20c m)mo re th an 7.9in (20cm)Parts DescriptionControl PanelAir Outlet GrilleHandleFilterAir intake GrilleBucket Drain Hose OutletHumidity SensorPOWER buttonPress to turn the dehumidifier on and off.SETTING buttonThe humidity level can be set within a range of 30%RH to 80%RH in 5% increments. -When it starts work, it will first automatically detect and show the room's humidity(and temperature). Press the "SETTING" button to change the humidity selection in 5% increments. It can be set circularly. (After you have set the desired humidity, the readout will display the actual room humidity.)-When the humidity level overtakes or drops to the level you set, the dehumidifier will automatically begin working or stop.-When the humidity level is set at 30%RH, the dehumidifier will be at CONTINUOUS dehumidifying mode.TIMER ButtonThe "TIMER" Button enables you to either Delay Start or Delay Stop the unit in the choice from 1 hour to 24 hours. In the shutdown state, the timer is set to the timing boot. In the boot state, the timer is set to the time shutdown.TIMER setting:1. Press "TIMER" button to change the delay timer at 1 hour increments, up to 24 hours. The control will count down the time remaining until start.2. Click “TIMER” button, the control will display the room temperature like before. Click “TIMER” button again at any time will stop the TIMER function.-Turning the dehumidifier ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the Auto Start/Stop function.- Before entering TIMER setting, make sure power is being supplied to the unit.- Before entering TIMER setting, make sure pressing Setting Button sets one desired room humidity first.SPEED ButtonControl the fan speed. Press to select either High or Normal fan speed. A higher fan speed will result in quicker moisture removal. Set the fan control to High for maximum moisture removal. When the humidity has been reduced and quietoperation is preferred, set the fan control to Normal."BUCKET FULL" Indicator LightsWhen the bucket is full, the light will flash and the machine will automatically shut off. After the water in the bucket is emptied, put the bucket back in place, then the indicator will go out, and the machine will restart.Auto Defrost FeatureWhen the dehumidifier is running at a lower temperature, the system will automatically determine if there is frost, and if if frost is present, it will automatically defrost.Defrost actionThe fan runs at high wind speed while the compressor stops, and theLED screen display the defrosting symbol.Power on: Compressor start after fan work a few seconds.Power off: Compressor shut down at once, after a few seconds, the fan stop (when other malfunctions occurs or humidity reached the desired level, the fan will stop after tens of seconds ).Tips: The compressor features "3 minutes delay protection"unction —— While the dehumidifier is powered, the compressor can only start again three minutes after its last shutdown.Action DescriptionNote:Fault & Protection Codes:Attention:1. If the display reads “E1”, “E2” or “E4” error codes, please turn off and unplug the unit, and check for any obstructions. Plug it in again and restart the dehumidifier,2. When one of the above malfunctions occurs, the buzzer will alarm for a few seconds. Press any key during the alarm to release the alarm sound.-If the malfunction is still present, please don‘t hesitate to contact Yaufey Customer Serviceemail:*************************.Note:Before starting the machine, please ensure that the air outlet has been opened, otherwise the machine will overheat. Do not pull out the power cord directly to stop the machine.There are two ways to remove collected water:1. Use the bucketWhen the bucket is full, remove the bucket and empty it.Note:Replace the empty bucket back into the unit and once seated correctly, the unit will start up again.- You should hear a click when the bucket is in the correct position.- Do not remove the float in the bucket, otherwise the sensor will not be able to sense the water level properly, so that the water will overflow from the bucket when the bucket is full.- If the tank is dirty, only can be used in cold or warm water wash, do not use detergent, steel wool, chemical processing dust cloth, gasoline, benzene, thinner or other solvent treatment, otherwise it may cause damage to the tank Water Leakage.Continuous Drainageat the continuous drainage portPicture 1: Example of error connection,Picture 2: Example of error connectionPicture 3: Example of a correct connectionThe groundContinuous drainage Pipe installationThe groundOperationThe continuous drainage function can be realized by connecting the drainage pipe Continuous drainBucketCare & CleaningWARNING:Turn the dehumidifier off and remove the plug from the wall outlet before cleaning.1. Clean the bucketClean the bucket with water every two (2) weeks.2. Clean the air filterClean the filter with clean water at least once every 30 days.3. Storing the dehumidifierWhen not using the dehumidifier for long periods- After turning off the dehumidifier, wait one day before emptying the bucket.- Clean the main dehumidifier, bucket and air filter.- Wrap the cord and bundle it with the band.- Cover the dehumidifier with a plastic bag.- Store the dehumidifier upright in a dry, well-ventilated place.CAUTION:Do not operate the dehumidifier without a filter. Because dirt and lint will clog itand reduce performance.TroubleshootingBefore calling Yaufey customer service, review this list. It may save you time and expense. This list includes the most common occurrences that are not the result of or materials in this dehumidifier.defective craftTechnical specificationsWarrantyYaufey offers a 12-month warranty on all of our products purchased new and unused from Yaufey Technologies Co.,Ltd. or an authorized reseller, with an original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faultymanufacturing, parts or workmanship during the Warranty Period. The warranty does not apply where damage is caused by other factors, including without limitation:(a) Normal wear and tear;(b) Abuse, mishandling, accident or failure to follow operating instructions;(c) Exposure to liquid or infiltration of foreign particles;(d) Servicing or modification of the product other than by Yaufey.These are our general terms for the warranty service, but we always urge our customers to reach out to us with any issue, regardless of warranty terms. If you experience anissue with a Yaufey product, please contact us at Email: ******************,we will do our best to resolve it for you.Get That WarrantyRegister your product within 14 days of your purchase to receive an extra bonus year on your warranty!1. Visit /account/register2. Enter in your purchase information and opt into our exclusive community.3. Receive wellness tips, style inspiration, a chance to win free product giveaways,an the inside scoop on Yaufey products in your inbox.Contact Us******************Home Dehumidifier(Scan the QR Code Get More)。

DH-9028C 除湿机 使用说明书

DH-9028C 除湿机 使用说明书

清水清洁过洁 网上的灰尘,将过滤网晾 、
干后装回原位 , 或用手轻轻的拍去过滤
网上的灰尘

功性机 。
正在能化霜停或湿控 、 定时关机
结时, z;;自动恢复工作, 风日十开始转动 。 待自动化 霜 结束 , 就会自 动 恢 复 工作
化霜束 、 湿控 、定时关机功能 A
机 转 泵

"凤肘" 闪亮 , 雪花图 案长亮

常见现象与故障排除
圄面跑凰盟国
DEHUMIDIFIER CHKAWAI






温度自 不
1 1 除 湿机若发生故障,请立刻切断电源,从插座上拔下电源插头,检查下列事项|
现象与故障
插上电源.数码管不亮
能动 控制 (化霜)
数码管显示 cc
化霜温度传感器有故障
更换温度传感器



中斤

1.检查电源 .
2
产品结构说明
3
控制面板及操作方法
5
排水方法
7
维修保养
8
常见现象与故障排除
9
技术规格及装箱清单
12
使用须知
使用注意事项:
DEHUMI D IF t 屯 RC HKAWA I
产晶结构说明
DEHUM I DIFIER CHKAWAI
. .圈盟
控制面板
·在平坦坚固的地面上使用,机体进出口请勿摆放物品,以免阻碍
2 插好插头,接通电源3 更换控制板
1 检查温度传感器连线和接插件 2 调换温度传感器 ,
量 少
除 j显 量 少
进出风口 是否堵 塞 室内温度和温度是否太低

冷冻除湿机组新使用说明书

冷冻除湿机组新使用说明书

冷冻除湿机组安装使用说明书NANJING TICA AIR-CONDITIONING CO,.LTD.南京天加空调设备有限公司注意:请在安装使用本机组之前,认真阅读本安装使用说明书,并妥善保目录一、适用范围及特点•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••1二、性能参数•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••2三、外形尺寸•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••2四、系统原理图•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••3五、电气原理图•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••3六、安装与调试••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••4七、注意事项•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••6八、维护保养•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••7九、故障分析和诊断••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••7一、适用范围及特点TICA(天加)除湿机是公司利用先进制造工艺手段,根据冷冻除湿原理设计开发的一种用于去除空气中水分的特种空调除湿设备,其在设计上最大限度满足了用户对产品功能、性能、结构等全方位要求。

多乐信工业除湿机DR-1382L除湿机使用说明书

多乐信工业除湿机DR-1382L除湿机使用说明书
2
智能除湿机
智能除湿机
智能除湿机
第四章,操作控制
湿控
12:30 定时关机
11:30 定时开机
化霜 12:00
开/关
ON/OFF
智能除湿机
湿度增/时钟增键
湿度减/时钟减键
4.1、按键功能说明: 1、“开/关”键 按该键开机,蜂鸣2声,进入开机模式,显示“运行”。 按该键关机,蜂鸣1声,进入关机模式,不显示“运行”。 2、设置键(定时时钟键) 按一次,进入当前时间设定,“时钟”闪,加键调节小时,减键调节分钟。 按二次,进入定时开机设定,“定时开机”闪,加键调节小时,减键调节分钟。 按三次,进入定时关机设定,“定时关机”闪,加键调节小时,减键调节分钟。 连续按到第四次,取消定时开关机设定,“定时开/关机”文字不显示。 此外只有在开机后才能设置定时开/关机时间。 3“+”键 直接按此键可对设置湿度进行操作,每按一次蜂鸣器响一声,设定湿度增 1%RH,连续按住可对设定湿度进行连续操作;当按”定时/时钟“键后再 按该键是对时间(小时)进行操作。 3“-”键 直接按此键可对设置湿度进行操作,每按一次蜂鸣器响一声,设定湿度减 1%RH,连续按住可对设定湿度进行连续操作;当按”定时/时钟“键后再 按该键是对时间(分)进行操作。
-6-
智能除湿机
智能除湿机
智能除湿机
智能除湿机
智能除湿机
第一章 安全说明
1.1安全与警示 除湿机符合中国标准,欧洲标准的各项规范和标准的安全要求,并在设计与制造方面 兼顾人员和设备的安全性。本手册的每一章节中,都有安全性的信息,也明确指出了 具有危险性的操作,并在前面标上了危险符号以作警示。 本手册提供了最好的除湿机操作经验和程序,但这些建议仅作为指导,并不承担任何 个人责任或履行当地的安全法规。在安装和操作设备的时候,每个人都须承担以下责任: • 按照本手册的描述和说明保护设备的安全。 • 顾及自己和他人的安全。 • 除湿设备必须由具备相关专业资质的人员进行操作和维护。 • 电气零配件必须由经授权的电气安装人员进行维护。 • 禁止在配有防爆装置的区域内安装除湿设备。 • 在开启任何维护面板前,应将除湿设备从主电源上断开。 • 当操作结束后,除湿设备应至少冷却5分钟,随后才可以对其进行维护。 • 如果未对除湿设备进行维护,则维护面板应处于关闭状态。 • 除湿设备仅限于在大气压力状态下对空气进行除湿。 • 禁止在未安装过滤装置的情况下,使用除湿设备。如未安装过滤装置,除湿设备的 表冷器将被污染,从而丧失除湿能力。 • 禁止删除或涂改除湿设备上的标示和说明。 • 本手册应被妥善保存。 • 应采用原装设备的备用零件。 • 在对设备进行任何调整或修改前,必须获得(dorosin多乐信)的书面许可。 1.2设备适用范围 多乐信DR系列除湿设备采用直接蒸发冷却设计,可对大气压力状态的空气进行干燥 处理。该除湿设备可对100%相对湿度内,温度范围在5 °C 至 38 °C之间的空气进行 除湿。其工作原理是风机将室内空气或室外混合空气通过表冷器进行除湿升温后送入 室内,使室内湿度降低,以满足人们的舒适性要求。 本设备的适用正常工作温度范围:在5—38摄氏度温度范围内,多乐信系列除湿机能 正常工作,超出此范围型除湿机将不能正常工作,不属于设备本身质量问题。 1.3手册内容 本手册面向于除湿机的广大用户,其中包括安装,操作,保养以及基本故障分析等内容。 本手册的用途就是为用户了解设备的结构和功能提供必要的信息,以便在杭州多乐信 电器有限公司提供服务前指导用户安装,操作,保养以及基本的故障分析。

松井电器工业除湿机说明书可以改修订稿

松井电器工业除湿机说明书可以改修订稿

松井电器工业除湿机说明书可以改WEIHUA system office room 【WEIHUA 16H-WEIHUA WEIHUA8Q8-通用版工业除湿机使用说明书目录1、重要安全说明 (2)2、产品介绍 (2)3、设备使用注意事项 (3)4、设备说明 (3)5、设备安装 (4)6、设备开机检查事项 (5)7、设备操作规程 (5)8、产品日常维护 (7)9、常见故障分析及排除方法 (7)10、故障代码说明 (8)为了您能正确的使用机器, 敬请阅读说明书一、重要安全说明使用本电器之前,敬请阅读所有说明。

●使用前,请先确认电源为220V/50HZ或380V/50HZ。

●不要以拔出电源线的方式来停止除湿机运转。

●在移动除湿机时应小心,不要滚压和损坏电线。

●切勿将手指或棒状物伸入格栅内。

●切勿让小孩攀爬,站立或坐在除湿机的电源线。

●建议使用合适的电源开关,勿使用插头,必须安全接地。

●不得操作于密闭狭窄空间。

●请妥善保管此使用手册。

注意:我们建议,任何维修必须由专业人员进行。

二、产品介绍除湿机可降低所安装房间的空气湿度,让人们在当中舒适生活或存储物品。

本公司的除湿机具有外形美观、结构紧凑、操作简便等特点,广泛应用于科研、医疗卫生、商品储藏、地下工程以及厨房、浴室、档案馆、仓库等高湿度场所去湿,可防止仪器、仪表、电讯器材、药品、资料等受潮、锈蚀、霉烂而造成的损失。

1、控制面板2、进风栅格面板3、过滤网4、脚轨5、出水管6、出风口三、设备使用注意事项a)使用环境:本设备只提供在房间内使用使用环境温度:5―38摄氏度避免使用在腐蚀性较强和易燃、易爆及大量灰尘的环境中;b)使用电源本机使用380V/50HZ电源,三相五线,机身背面有接地标志,使用前务必做好接地线连接。

本机安装必须由专业电工安装,若无专业电工,可电话联系生产工厂指导安装.c)机器开关机器控制面板上有开关键,严禁直接开关空开的方式进行开关机;d) 维护★维护前务必先关闭机器,切断机器电源;★严禁攀爬机器,或站到机器上面。

尚瑞特转轮除湿机说明书

尚瑞特转轮除湿机说明书

尚瑞特转轮除湿机说明书
目的:建立转轮除湿机使用、维护、保养、润滑标准操作规程。

范围:转轮除湿机。

责任:设备员、操作工、维修工、车间主任、设备科长、QA监控员。

内容:
1、检查有无设备"完好”证。

1.2开机,合上QFi,QF:及QF;空气断路器,微电脑控制器上的电源指示灯亮,控制器上的液品屏显示"欢迎使用西漳除湿设备厂除湿机”。

1.3设定参数(出厂前各参数已设定好,无特殊要求,不必重新设定)。

1.4按下“再生开”按钮,KM,,KM;吸合,转轮电机和再生电机开始工作,延时10秒后,加热器根据ST,设定的温度开始加热。

1.5按下“除湿开”按钮,处理风机电机开始工作,除湿机处于除湿状态。

1.6按“选择"键可任意观察图文显示的上电状态。

设定参数,实时测量值及曲线系统运作状态,故障状态五幅画面。

1.7停机,按下“除湿关”按钮,则加热器和处理风机电机停止工作,此时转轮电机和再生风机继续运行,同时进入关机延时状态,待延时时间
到,则转轮电机和再生风机电机停止工作,并记录关机时的测量值或故障现象,最后分离馈电空气断路器,切断总电源。

2、维护保养
2.1一个月后处理空气和再生空气过滤器,将过滤器无纺布取下清洗惊干。

2.2三个月后在电机轴承,减速箱以及转轮链条处调换或加钙基河滑脂;打开转芯门板,用吸尘器清除积尘。

转轮除湿机说明书

转轮除湿机说明书

转轮除湿机目 录1. 安全规则 (1)1.1 安全细则........................................................................................................... .11.2 安全标识 (1)1.3 工作环境 (2)2. 注意事项 (2)3. 型号简述 (2)4. 特点 (3)5. 机器规格 (3)5.1 机器规格表 (3)5.2 干燥能力对照表 (4)6. 如何选型? (4)7. 工作原理及相关说明 (5)7.1 工作原理 (5)7.2 相对湿度与露点 (5)7.3 为何要使用除湿机? (5)8. 工作原理示意图 (6)9. 安装调试 (7)9.1 安装示意图 (7)9.2 安装注意事项 (8)9.3 安装步骤及相关说明 (8)10. 操作说明 (10)11. 故障排除及保养 (11)11.1 故障分析及排除 (11)11.2 机器保养 (12)12. 电路图 (14)12.1 主电路图 (14)12.2 控制电路 (15)12.3 电器位置图 (16)尊敬的客户:感谢您使用本公司生产的除湿干燥机,以及对我们公司的信任和关爱。

在使用本机前请仔 细阅读使用手册,以便正确使用机器,避免因操作不当造成人员受伤或机器损坏。

1、安全规则11. 安全细则使用本机时,为避免触电、火灾或人员伤亡,请严格遵守下列基本安全措施:)仔细阅读和理解全部操作说明和注意事项。

)使用时请注意电源、电压是否相符,按照机身上注明的警告及指示来操作和使用。

)请务必请专业人士将本机接入地线电源。

)在清洁本机时,请先拔掉电源插头。

请勿使用液体或喷雾清洁机台,须用湿布擦拭。

)机身上的缝隙和开口用于通风,请勿堵塞或掩盖。

)切勿让插座和分线过载,否则会导致火灾或触电。

)本机设有自动开关装置且可能自动预热,任何易燃易爆物品请远离机台。

)关机时须先关闭“系统运转开关”,再关闭“主电源开关”。

除湿机操作说明

除湿机操作说明

除湿机控制器功能说明书1 总技术要求采用单压缩机,风扇单、双档风速控制,采用毛细管节流。

具有各种保护及显示功能。

1、1 工作电压:单相交流220VAC/50Hz;1、2 输入功率(W):视能力而定;1、3 除湿量:取决于系统;1、4 功能:除湿及除霜;1、5 保护功能:符合本控制方案得要求;1、6 安全要求:符合GB4706、32-1996;1、7 EMC要求:符合GB4343、2-99及有关家电产品得IEC标准。

2 操作面板2.1 除湿机得操作面板由一个LCD液晶屏、指示灯(红/绿色)与五个按键组成(如下图)。

注:五个按键,从左到右分别为“电源“(POWER)键,“菜单”(MENU)键,“调节”(ADJUSTMENT)键,“开始/停止除湿”(START/STOP)键,“水泵开/关”(PURGING)键。

2.2 液晶屏显示内容,见下图。

3 操作3.1 参数设定内容,见下表。

参数代号意义单位分辨率默认值调整范围3.2 参数设定3.2.1 在关机状态下,先按“除湿”键,再按“菜单”键持续5秒,背光屏亮,蜂鸣器短响,进入参数设定状态。

3.2.2 显示内容为“P0:20”;“20”处于闪烁状态,频率为1Hz。

“P0”为参数号,按“开始/停止除湿”键来实现从“P0~P6”得切换;“20”为对应参数值,按“菜单”键调整对应参数值。

3.2.3 完成参数设定后,按“电源”键,则熄灭背光屏、蜂鸣器短响、退出并保存参数值,返回关机状态。

进入设定后15秒之内没有按键,则自动保存参数值并退出,返回关机状态。

3.3 运行操作3.3.1 在关机状态下按“电源”键,进入待机状态。

3.3.2 在待机状态,默认显示“当前湿度(CURRENT)”工作环境得湿度值。

液晶屏上部分显示:3.3.2 、1 “时钟图标群组”(P17 –‘时钟图标’,P41-‘大方框’,P18-‘TIMER’,P20 -‘TOTAL’,P22 -‘JOB’)、“湿度图标群组”(P24 -‘湿度’,P42 –‘大方框’,P26 -‘小方框’,P27 –‘SET’)、“温度图标群组”(P29 –‘温度’,P43–‘大方框’,P30 -‘华氏度(o F)’,P32 -‘摄氏度(o C)’)图标亮;3.3.2 、2 “P25 -‘CURRENT’”图标闪烁,频率为1Hz,闪五次后不闪,图标亮。

除湿机使用说明书.pdf_1694356640.3846452

除湿机使用说明书.pdf_1694356640.3846452

1安全使用及维护注意事项2-3一般故障排除445-6保护功能及维护保养 7-89其他10目录产品简介及安全注意事项 机件介绍控制面板介绍使用说明*请确保有可靠的接地线。

在使用本除湿机之前,请您仔细阅读以下内容,以确保正确、合理使用本除湿机。

下列的注意事项,为涉及安全的重要内容,当操作错误时可能引起不必要的事故。

因此,在使用本除湿机时务必遵守!■安全注意事项产品简介及安全注意事项■产品介绍核心部件:采用国际名牌旋转式压缩机,比同等制冷量制冷剂的往复式压缩机制冷效率高且省电。

其 它 4. 保修卡 一张3. 合格证一个2. 使用说明书一份■执行标准■三包条例■装箱单1. 除湿机一台GB4706.1 32GB4706. GB4343.1 GB17625.1* 全及售后服务质量,请认准有“3C ”标志的产品。

2、考虑人的生理健康条件及室内家俱和其他物品的保护 条件,如无特殊要求,建议湿度设定在RH50%~70% 间较为适宜,且省电.温馨提示:1、除湿机是国家“3C ”强制认证产品,为保证您的使用安 本产品实行用说明书”,凡因产品质量问题而发生故障,本厂特约维修部给予免费修理,但因使用不当或超出保修期后出现的问题,在修理时酌情收取工本费。

“三包",保修期一年。

保修期内,如发现产品不妥,请先参阅“使原因分析电源插头没有插入插座插座电源没有接通电控板保险丝熔断电控板变压器损坏环境湿度低于设定湿度电源插座缺少零线电源插座电压偏低电机电容损坏卡轴内部线圈损坏压缩机电容损坏卡缸内部线圈损坏故障现象排除方法机器不能运转无电源显示有电源显示将插头插入插座恢复电源更换保险丝更换变压器根据需要重新设定增加零线恢复正常电压E1E2温度传感器损坏湿度传感器损坏更换温度传感器更换湿度传感器E3(制冷系统异常)电机工作不正常压缩机工作不正常更换电容更换电机更换电机更换电容用大电容冲击更换压缩机缺少制冷剂查找漏电,予以修复,重新抽真空,加制冷剂空气过滤网积垢清洗过滤网除湿机进出风口有障碍物去除障碍物门窗开着关闭门窗并利用窗帘遮阳机器除湿效果不好噪音机器放置不平稳过滤网堵塞将机器重新放置平稳清洗过滤网漏水机器倾斜将机器调整水平出水管堵塞(连续排水)清除管内异物安全使用及维护注意事项本机使用容量匹配的专用线路及插座,禁止引线或使用移动插座。

工业除湿机使用说明

工业除湿机使用说明

工业除湿机使用说明说到湿气,哎呀,真的是个烦人的家伙!你家里的衣服一晚上挂着湿乎乎的,第二天一摸就像是刚从水里捞上来的,感觉都不敢穿出去见人。

而且不止是衣服,空气湿哒哒的,墙角也开始发霉,地板湿漉漉的,走路像踩水,一不小心脚趾头都得泡水。

这时候,你会突然感叹:“要是有个能帮忙除湿的机器就好了!”嘿嘿,工业除湿机来啦!它就像是湿气的克星,能帮你解决这个大难题。

工业除湿机,顾名思义,主要就是用来除湿的机器,尤其是大面积场所里,那种湿气特别重的地方。

你看,家里不行,车库不行,厂房、仓库、商场这种地方,湿气真的能让人头疼。

不管是夏天的潮湿,还是梅雨季节的湿气,甚至是冬天的水蒸气,工业除湿机统统可以搞定!它的工作原理其实很简单,就是把空气中的水分吸进去,经过冷凝和过滤的过程,去掉那些多余的水蒸气,最后干燥清爽的空气再被送回房间。

听起来是不是很神奇?但它真的是又高效又靠谱!不过,别看它的名字那么酷,使用起来其实一点也不复杂。

你一开始把它放在房间或者仓库的角落,接上电源,一按开关,哦啦啦,工作开始了!工业除湿机通常有不同的模式,根据你的需求可以选择。

比如,低湿度环境时你可以开低档工作,这样它就不会太消耗电力,而如果是湿气特别重的地方,那就开高档,一下子把水分给拉走!再说,很多机器上都有自动湿度调节功能,机器会根据房间的湿度自动调节工作,省时又省力,简直就是懒人必备!但是,你以为这么简单就完事了吗?当然不是,机器也有需要注意的小细节。

它是个“嘴巴很大”的机器,吸湿能力特别强,所以你需要确保它的空气流通顺畅。

如果空气进不去,湿气可就没法排出去了,那你还指望它干嘛?很多工业除湿机都有排水管设计,这就意味着你不需要老去倒水,直接把水排到外面,方便省事。

可是,有一点需要特别留意,水管堵了,机器就得停工。

你说说,既然都买了除湿机了,当然得用好它对吧?不然一切白搭!哦对了,大家可能会担心它的噪音问题,毕竟工业除湿机可不是家用那种小型设备,声音可能稍微大一点。

福建工厂降温除湿机说明书

福建工厂降温除湿机说明书

福建工厂降温除湿机说明书本说明书介绍了福建工厂降温除湿机的使用方法、技术参数和保养维护等内容,以帮助用户正确、安全地操作和维护该设备。

1. 简介福建工厂降温除湿机是一种专业的工业设备,为工厂和仓储场所提供除湿和降温服务。

它采用先进的除湿技术和制冷技术,能够高效地去除湿气,降低空气温度,从而改善工作环境和保护货物。

2. 使用方法2.1 接通电源首先,将降温除湿机的电源插头插入电源插座,并确保电压和频率与设备标牌上的要求一致。

然后,打开电源开关,使设备通电。

2.2 调整湿度降温除湿机通电后,可通过设备面板上的湿度调节器,调整设备的湿度设定值。

根据实际需要,将湿度设定在合适的范围内,以达到最佳的除湿效果。

2.3 开启风扇和制冷器在设定好湿度后,打开风扇和制冷器。

风扇将会开始工作,将室内空气吹入设备内部,制冷器则会开始降低空气温度和除湿。

3. 技术参数福建工厂降温除湿机具有以下技术参数:- 除湿能力:根据不同型号而定,通常在每小时10-50升之间。

- 制冷功率:根据不同型号而定,通常在1-5千瓦之间。

- 电源电压:根据不同型号而定,通常在220V或380V之间。

- 噪音:根据不同型号而定,通常在50-70分贝之间。

- 外形尺寸:根据不同型号而定,通常在1-2米之间。

4. 保养维护4.1 定期清洁为了保持福建工厂降温除湿机的正常运行,定期进行清洁是必要的。

首先,关闭设备电源,然后用软布或吸尘器清除设备表面的灰尘和污垢。

同时,还应清洁设备内部的过滤器,以确保其畅通无阻。

4.2 定期检查定期检查设备的各个部件是否正常运行,特别是风扇和制冷器。

如果发现异常情况,应及时联系专业维修人员进行维修或更换相关零部件。

4.3 防止过载福建工厂降温除湿机在使用过程中,应确保不超过其额定工作负荷。

如果需要长时间连续工作,可以选择更大容量的设备,以避免因超载而损坏设备。

综上所述,福建工厂降温除湿机是一款高效、可靠的工业设备,能够为工厂和仓储场所提供除湿和降温服务。

工业除湿机说明书新

工业除湿机说明书新

实用文档通用版工业除湿机使用说明书可林艾尔电气(苏州)有限公司发布(本说明书适用于CFZ-7S、8.8S、10S、15S、20S、30S、35S、40S等型号除湿机)目录1、重要安全说明 (2)2、产品介绍 (2)3、设备使用注意事项 (3)4、设备说明 (3)5、设备安装 (4)6、设备开机检查事项 (5)7、设备操作规程 (5)8、产品日常维护 (7)9、常见故障分析及排除方法 (7)10、故障代码说明 (8)为了您能正确的使用机器, 敬请阅读说明书一、重要安全说明使用本电器之前,敬请阅读所有说明。

●使用前,请先确认电源为220V/50HZ或380V/50HZ。

●不要以拔出电源线的方式来停止除湿机运转。

●在移动除湿机时应小心,不要滚压和损坏电线。

●切勿将手指或棒状物伸入格栅内。

●切勿让小孩攀爬,站立或坐在除湿机的电源线。

●建议使用合适的电源开关,勿使用插头,必须安全接地。

●不得操作于密闭狭窄空间。

●请妥善保管此使用手册。

注意:我们建议,任何维修必须由专业人员进行。

二、产品介绍除湿机可降低所安装房间的空气湿度,让人们在当中舒适生活或存储物品。

本公司的除湿机具有外形美观、结构紧凑、操作简便等特点,广泛应用于科研、医疗卫生、商品储藏、地下工程以及厨房、浴室、档案馆、仓库等高湿度场所去湿,可防止仪器、仪表、电讯器材、药品、资料等受潮、锈蚀、霉烂而造成的损失。

三、设备使用注意事项a)使用环境:本设备只提供在房间内使用使用环境温度:5―38摄氏度1、控制面板2、进风栅格面板3、过滤网4、脚轨5、出水管6、出风口避免使用在腐蚀性较强和易燃、易爆及大量灰尘的环境中;b)使用电源本机使用380V/50HZ电源,三相四线,机身背面有接地标志,使用前务必做好接地线连接。

本机安装必须由专业电工安装,若无专业电工,可电话联系生产工厂指导安装.c)机器开关机器控制面板上有开关键,严禁直接开关空开的方式进行开关机;d) 维护★维护前务必先关闭机器,切断机器电源;★严禁攀爬机器,或站到机器上面。

川井除湿机 252B(新版)说明书

川井除湿机 252B(新版)说明书

温 保 40
化 霜 50
干 衣1 干 衣2
60 70 80
h
DH-252B
川 井 R RH %
+
开/关
-
ON/OFF
设 ADJUST

! 注意

能微 川井 d




C
HK
A
W
A
除湿机 I
水满
湿 控 30
温 保 40
化 霜 50
干 衣1 干 衣2
60 70 80
h
DH-252B
川 井 R RH%
+
开/关
DH-252B
30
40
50
60
70
80 h
RH%
R
川井
+
-
开/关 设 定
6
智能微电脑控制
川井d 除湿机 CHKAWAI
DH-252B
水 满 30
湿 控 40
温保
50 60
化 霜 70
干衣1 80
干 衣2
+
h
RH%
R
川井
-
开/关 ON/OFF
设定 ADJUST
7
8
9
10
智能微电脑 川井 dCHKAWAI
H
K
A
WA
除湿机 I
水满
湿控
30
温保
40
化霜 干 衣1 干 衣2
50 60 70 80
DH-252B
h
川 井 R RH %
+
ON开/OF/F关
设 ADJUST

-

卓邦工业除湿机使用说明

卓邦工业除湿机使用说明

卓邦工业除湿机使用说明一、工业除湿机怎么使用1、确定环境温度常规的工业除湿机使用范围建议在5~40℃。

当周围温度5℃时,附着于蒸发器表面的水滴会结霜而使机器的除湿效果减弱;如果周围温度超过40℃时,系统内压力会增高,压缩机过载,会造成压缩机马达毁损。

2、静置后使用工业除湿机在运输、安放过程当中,不可避免地会有震动、侧倾等动作,导致压缩机内的制冷剂发生移位。

如果马上开机使用,制冷剂倒灌,空转时容易烧坏压缩机。

因此,需要把工业除湿机静置2~4小时间,让压缩机内的制冷剂回流到位再通电使用。

3、放位置选择工业除湿机应该放置在空气流通、地面平整的地方,这样可以让潮湿空气被抽入除湿机中,让干燥空气迅速循环至厂各个角落,达到好的除湿效果。

另一方面,机器不要紧挨着墙壁,因为在长时间运行之后,机器温度会不断上升;机器进风口处应与货物保持距离,机器部严禁摆放货物,避免造成堵塞影响循环效果。

4、通电使用建议工业除湿机在开启之后尽量使其处于通电待机状态,不要频繁开启。

百奥工业除湿机自带温湿度监控传感器,控温控湿,机器开启后不需要频繁人工启闭,这样可以降低对机器性能的破坏,减少电能的浪费。

长期不使用机器可以切断电源;停电后建议立即关闭电源,防止突然来电,大电流对设备造成突然冲击,损坏除湿机。

所以,机器在接线时最好安装一个空开,方便机器断电使用。

5、机器保养清洁长时间使用除湿机,进风口处容易堵塞,引起进风不顺,直接影响除湿效果,所以需要定期清理除湿机的进风口、出风口及过滤网。

在清理过滤网时,确保机器电源已经拔掉。

拆掉过滤网,用清水清除灰尘后置于阴凉处吹干,再装回原处。

不可使用腐蚀性化学物品清洗或在太阳下直射,以防过滤网损坏或变形。

需要清理机器外表,可以使用加入软性清洁剂的软布进行擦拭,切勿用水直接冲洗。

二、工业除湿机工作原理除湿机的原理:调温调湿机组分风冷管道除湿机与水冷管道调温除湿机,由压缩机、四通阀、室外换热器、室内第二换热器、室内第一换热器、膨胀阀等过制冷剂管路连接成一个制冷循环,其中室外换热器与室内第二换热器两个支路并联,并在室内第二换热器的支路上安装用来控制支路通断的电磁阀。

Ebaq Triton工业除湿机使用说明书

Ebaq Triton工业除湿机使用说明书

EBAC MODEL TRITON INDUSTRIAL DEHUMIDIFIER OWNER’S MANUALINTRODUCTIONDesigned for a wide range of applications, the Triton dehumidifier is a super high capacity industrial unit which provides fast and efficient drying.The Triton has a number of special features:•Super high efficiency rotary compressor•Temperature-sensitive microprocessor controlled defrost system•Exterior epoxy powder-coated finish•Inlet air filter•Internal condensate pump•Pump purge system•Rugged trolley for portability•Retractable handle mechanism•Extra long power cordThe fan draws the moist air through the inlet grille on the back of the unit, then through the cold evaporator coil, which cools the air below its dew point. Moisture forms on the evaporator coil and is collected in the condensate tray, which is equipped with a permanent drain. The cooled air then passes through the hot condenser coil where it is reheated using the same energy removed during the cooling phase, plus the additional heat generated by the compressor. The air is, therefore, discharged from the dehumidifier at a slightly higher temperature with a lower absolute humidity than that which entered. Continuous circulation of air through the dehumidifier gradually reduces the relative humidity within the area.The Triton dehumidifier is a rugged, reliable drying unit designed to operate effectively over a broad range of temperature and humidity conditions.The unit incorporates a welded and galvanized steel chassis and is finished in an epoxy coating for resilience to damage caused by rough handling.SPECIFICATIONSM ODEL: TRITONH EIGHT: 29”W IDTH: 20”D EPTH: 16”W EIGHT: 75 lbsA IRFLOW: 282 CFMP OWER S UPPLY: 115V/ 60Hz/ 1 phF INISH: Powder-coated Epoxy O PERATING R ANGE: 41°F – 100°FR EFRIGERANT: R-22 (16.2 oz)OPERATIONThe following procedures should be followed to test the Triton for correct operation:1. After unpacking, examine all external features to confirm damage-free shipment.Report all defects and damage at once. Connect the power cable to a grounded 15Amp electrical outlet.2. Check dehumidification process as follows:CAUTION:DO NOT REMOVE COVERS WHEN UNIT IS INOPERATION.A. Place unit on a level surface.B. Start up unit by switching to “ON”.C. Check that air is being delivered through the front outlet grille and thecompressor is running.D. Leave the machine running for 60 minutes.E. Check to ensure there is sign of water extraction through the condensate drain.F.Test the pump surge system operation by holding the momentary pump switch for5 to 10 seconds. This switch allows you to drain the pump reservoir at the end ofa drying jobIf, after carrying out the above procedures, the unit does not appear to function properly, refer to the Trouble Shooting section, which follows, or contact the Factory Service Center.CAUTION:Once the unit has been switched off, wait at least fiveminutes before restarting.ROUTINE MAINTENANCEWARNING: ENSURE THAT THE POWER CORD TO THE MACHINEHAS BEEN DISCONNECTED BEFORE CARRYING OUTROUTINE MAINTENANCE.To ensure continued full efficiency of the dehumidifier, maintenance procedures should be performed as follows:1. Replace or clean the inlet air grille as required. Clean the surface of the evaporatorand condenser coils by blowing the dirt out from behind the fins with compressed air.Hold the nozzle of the air hose away from the coil to avoid damaging the fins.Alternatively, vacuum clean the coils.WARNING: DO NOT STEAM CLEAN REFRIGERATION COILS.2. Check that the fan is firmly secured to the motor shaft and that the fan rotates freely.The fan motor is sealed for life and therefore does not need oiling.3. To check the refrigerant charge, run the unit for 15 minutes and briefly remove thetop cover. The evaporator coil should be evenly frost coated across its surface. Attemperatures above 70°F, the coil may be covered with droplets of water rather thanfrost. Partial frosting accompanied by frosting of the thin capillary tubes, indicatesloss of refrigerant gas or low charge.4. Check all wiring connections.I F ANY OF THE PRECEDING PROBLEMS OCCUR, CONTACT THE E BAC S ERVICE C ENTER PRIOR TO CONTINUED OPERATION OF THE UNIT TO PREVENT PERMANENT DAMAGE.REPAIRS1. Should an electrical component fail, consult the Factory Service Center to obtain thepart.properreplacement2. If refrigerant gas is lost from the machine, it will be necessary to use a refrigerationtechnician to correct the fault. Contact the Factory Service Center prior to initiatingthis action.Any competent refrigeration technician will be able to service the equipment. Thefollowing procedure must be used:a. The source of the leak must be determined and corrected.b. The machine should be thoroughly evacuated before recharging.c. The unit must be recharged with refrigerant measured accurately by weight.d. For evacuation and recharging of the machine, use the crimped and brazedcharging stub attached to the side of the refrigerant compressor.The charging stub should be crimped and rebrazed after servicing. N EVER allowpermanent service valves to be fitted to any part of the circuit. Service valvesmay leak causing further loss of refrigerant gas.3. The refrigerant compressor fitted to the dehumidifier is a durable unit that shouldgive many years of service. Compressor failure can result from the machine losing itsrefrigerant gas. The compressor can be replaced by a competent refrigerationtechnician.Failure of the compressor can be confirmed by the following procedure:a. Establish that power is present at the compressor terminals using a voltmeter.b. With the power disconnected, check the continuity of the internal winding byusing meter across the compressor terminals. An open circuit indicates that thecompressor should be replaced.c. Check that the compressor is not grounded by establishing that a circuit does notexist between the compressor terminals and the shell of the compressor.TROUBLESHOOTINGS YMPTOM C AUSER EMEDYUnit inoperative 1. No power to unit 1. Check the power from power supply panelLittle or no airflow 1. Loose fan on shaft2. Fan motor burnt out3. Dirty refrigeration coils4. Loose electrical wiring5. Fuse blown or circuit breakertripped1. Tighten fan2. Replace the fan motor3. See Routine Maintenance Section4. Check the wiring diagram to findfault and repair5. Replace the fuse or reset thecircuit breakerLittle or no water extraction 1. Insufficient air flow2. Compressor fault3. Loss of refrigerant gas1. Check all of the above2. Contact the Factory Service Center3. Contact the Factory Service CenterLittle or no defrost when required 1. Faulty timer2. Faulty by-pass valve1. Contact the Factory Service Center2. Contact the Factory Service CenterUnit vibrates excessively1. Loose compressor2. Damaged fan 1. Tighten the nuts on the compressor mounts2. Replace fanWater flooding inside the machine 1. Drain pipe blocked/frozen2. Drain pipe too high3. Crimped or blocked tubing1. Clear the obstruction2. Ensure that no section of thedrain hose is above the level of thewater outlet3. Straighten, clear, or replace tubingEbac Industrial Products, Inc.700 Thimble Shoals Blvd, Suite 109Newport News, VA. 23606-2575Tel: (757) 873 6800 Fax: (757) 873 3632Website TRITONSPARE PARTS LISTN UMBER D ESCRIPTION P ART N UMBER Q UANTITY(RGA5456EXA) 3022170 11 Compressor2 Compressor Overheat Protector N/A 1Capacitor 3030908 13 Compressor4 Evaporator/CondenserCoil 2139330 1 Filter 2013831 15 GrilleDryer 3020901 16 Filter7 Fan Motor 3035788 1Valve 3020811 18 By-passTimer 1609850 19 ElectronicFan 3040129 110 Axial11 RockerSwitch 3035914 1Assy 3035142 112 ThermistorCoil 3030421 113 Solenoid14 PVC Clear Tube 3014336 1Tubing 3014368 115 SiliconeTray 2131107 116 DrainFastener 3087720 117 QtrTurnCam 3087721 1 Turn18 QtrWasher 3087722 1 Turn19 Qtr20 Wheel 3050110 2Washer 3082601 421 1”StarlockPump 3160129 122 CondensateSwitch 3036779 123 PurgeDisconnect 3086144 124 Quick25 Snap Hose Clip 3086135 126 Hose Clip Snapper 3086136 127 Self Locking Pin-1/4x1.5 3087723 1Ebac LIMITED WARRANTYOur products carry a one-year unconditional warranty against any defects in workmanship or material. This warranty will cover all parts and labor required to repair your Ebac product. This warranty is invalid if the unit has been abused, damaged, whether intentional or accidental, or if any modifications have been made to the unit.THE FOREGOING WARRANTY IS EXCLUSIVE AND IS ISSUED IN LIEU OF ALL OTHER WARRANTIES (WHETHER WRITTEN, ORAL, OR IMPLIED) INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. EBAC SYSTEMS, INC. DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL DAMAGES, LOST PROFITS, OR INCIDENTAL DAMAGES FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THE FOREGOING DESCRIBED MERCHANDISE. For Your Records: Model: ____________________ S/N: ______________________ Date Received: ______________SAVE THIS SECTION FOR YOUR RECORDSCLIP AND RETURN THIS CARDPLEASE NOTE WARRANTY REGISTRATIONTo ensure that your Ebac Dehumidifier is accorded the full coverage provided by this warranty, please complete and mail thiscard at your earliest convenience.Thank YouDATE MODEL ___________ S/N ________________ RECEIVED ________________OWNER __________________________________________________________ADDRESS ________________________________________________________CITY __________________________ STATE ________ ZIP _______________ COMMENTS _______________________________________________________________________________________________________________________ Ebac Industrial Products, Inc.700 Thimble Shoals Blvd, Suite 109, Newport News, VA. 23606-2575Tel: (757) 873 6800 Fax: (757) 873 3632 Website 。

工业除湿机说明书新范本

工业除湿机说明书新范本

工业除湿机说明书新通用版工业除湿机使用说明书可林艾尔电气(苏州)有限公司发布(本说明书适用于CFZ-7S、8.8S、10S、15S、20S、30S、35S、40S等型号除湿机)文档仅供参考目录1、重要安全说明 (2)2、产品介绍 (2)3、设备使用注意事项 (3)4、设备说明 (3)5、设备安装 (4)6、设备开机检查事项 (5)7、设备操作规程 (5)8、产品日常维护 (7)9、常见故障分析及排除方法 (7)10、故障代码说明 (8)为了您能正确的使用机器, 敬请阅读说明书一、重要安全说明使用本电器之前,敬请阅读所有说明。

●使用前,请先确认电源为220V/50HZ或380V/50HZ。

●不要以拔出电源线的方式来停止除湿机运转。

●在移动除湿机时应小心,不要滚压和损坏电线。

●切勿将手指或棒状物伸入格栅内。

●切勿让小孩攀爬,站立或坐在除湿机的电源线。

●建议使用合适的电源开关,勿使用插头,必须安全接地。

●不得操作于密闭狭窄空间。

●请妥善保管此使用手册。

注意:我们建议,任何维修必须由专业人员进行。

二、产品介绍除湿机可降低所安装房间的空气湿度,让人们在当中舒适生活或存储物品。

本公司的除湿机具有外形美观、结构紧凑、操作简便等特点,广泛应用于科研、医疗卫生、商品储藏、地下工程以及厨房、浴室、档案馆、仓库等高湿度场所去湿,可防止仪器、仪表、电讯器材、药品、资料等受潮、锈蚀、霉烂而造成的损失。

三、设备使用注意事项1、控制面板2、进风栅格面板3、过滤网4、脚轨5、出水管6、出风口a)使用环境:本设备只提供在房间内使用使用环境温度:5―38摄氏度避免使用在腐蚀性较强和易燃、易爆及大量灰尘的环境中;b)使用电源本机使用380V/50HZ电源,三相四线,机身背面有接地标志,使用前务必做好接地线连接。

本机安装必须由专业电工安装,若无专业电工,可电话联系生产工厂指导安装.c)机器开关机器控制面板上有开关键,严禁直接开关空开的方式进行开关机;d) 维护★维护前务必先关闭机器,切断机器电源;★严禁攀爬机器,或站到机器上面。

除湿器使用说明书

除湿器使用说明书

除湿器使用说明书篇一:抽湿机使用说明抽湿机使用说明开机1. 打开电源开关。

2. 按一下“开\关”键,LED显示窗亮,所有显示正常后,LED显示窗显示当前环境湿度。

当设定湿度小于当前湿度,除湿机工作状态,如图1;当设定湿度大于当前湿度,除湿机停止运行状态,如图2 调节1. 温度设定:按动湿度增或湿度减键来调整你所需的湿度。

2. 定时设定:按第一下“定时/时钟”键,LED显示窗上“时钟”闪,通过按“加”、“减”键对当前时间的小时、分钟进行调整。

按第二下“定时/时钟”键,LED显示窗上“关机时间”闪,通过按“加”、“减”键对当前关机时间的小时进行设定。

设定好定时模式后,除湿机处于运行状态,则执行“定时关机时间”模式如果取消定时模式,按一下“定时/时钟”键,即可取消定时模式保养每月清洗空气过滤网一次责任人:何志强篇二:除湿器正确使用的方法除湿器正确使用的技巧南方地区,经常会碰到潮湿的天气,很容易引起室内受潮。

所以,做好去湿、防潮工作不容忽视。

下面就由小编为您浅谈:除湿器怎样为你创造舒适生活?使用方法:1,机体放置需平坦,不可倾斜或横倒,避免机器发生故障或异常异音。

加湿器内储水量过满,为免溢出污湿地面,而必须于运转中搬运机体时,请先拔掉电源线插头,再将储水桶内水倒掉。

2,除湿器使用时,室内温度要控制在合理的范围内。

低于15℃时,附着于蒸发器表面的水滴会结冰而使除湿机效果减弱,超过40℃以上时,系统内压力会增高而使压缩机过载,此时过载保护器应切断线路,否则压缩机马达会毁损。

3,不宜长途或剧烈搬动,需要将机体静置2-3小时后再接电源使用,避免压缩机受损;使用时,应该先把门窗关好,以免潮湿的外气进入室内影响除湿效果。

维护保养:1,冷凝器应该时常清洗,保持干净。

除湿机应置于室内中央位置,出入风口不得有阻碍物挡住,滤气网应清理干净。

2,清洗滤气网以40℃以下清水洗涤即可;用清洁剂清洗更好,洗掉灰尘后,用水冲干净,阴干后装回机体内。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

工业除湿机说明书新 Document number:BGCG-0857-BTDO-0089-2022通用版工业除湿机使用说明书可林艾尔电气(苏州)有限公司发布(本说明书适用于CFZ-7S、、10S、15S、20S、30S、35S、40S等型号除湿机)目录1、重要安全说明 (2)2、产品介绍 (2)3、设备使用注意事项 (3)4、设备说明 (3)5、设备安装 (4)6、设备开机检查事项 (5)7、设备操作规程 (5)8、产品日常维护 (7)9、常见故障分析及排除方法 (7)10、故障代码说明 (8)为了您能正确的使用机器, 敬请阅读说明书一、重要安全说明使用本电器之前,敬请阅读所有说明。

●使用前,请先确认电源为220V/50HZ或380V/50HZ。

●不要以拔出电源线的方式来停止除湿机运转。

●在移动除湿机时应小心,不要滚压和损坏电线。

●切勿将手指或棒状物伸入格栅内。

●切勿让小孩攀爬,站立或坐在除湿机的电源线。

●建议使用合适的电源开关,勿使用插头,必须安全接地。

●不得操作于密闭狭窄空间。

●请妥善保管此使用手册。

注意:我们建议,任何维修必须由专业人员进行。

二、产品介绍除湿机可降低所安装房间的空气湿度,让人们在当中舒适生活或存储物品。

本公司的除湿机具有外形美观、结构紧凑、操作简便等特点,广泛应用于科研、医疗卫生、商品储藏、地下工程以及厨房、浴室、档案馆、仓库等高湿度场所去湿,可防止仪器、仪表、电讯器材、药品、资料等受潮、锈蚀、霉烂而造成的损失。

1、控制面板2、进风栅格面板3、过滤网4、脚轨5、出水管6、出风口三、设备使用注意事项a)使用环境:本设备只提供在房间内使用使用环境温度:5―38摄氏度避免使用在腐蚀性较强和易燃、易爆及大量灰尘的环境中;b)使用电源本机使用380V/50HZ电源,三相四线,机身背面有接地标志,使用前务必做好接地线连接。

本机安装必须由专业电工安装,若无专业电工,可电话联系生产工厂指导安装.c)机器开关机器控制面板上有开关键,严禁直接开关空开的方式进行开关机;d) 维护★维护前务必先关闭机器,切断机器电源;★严禁攀爬机器,或站到机器上面。

清洗过滤网时,请勿弄湿进风口的湿度传感器。

严禁开机状态下清洗风机风叶;★机器安装好后,不能直接移动机身,否则将会损坏机器。

四、设备说明1.外观结构说明本机采用名牌压缩机, 微电脑湿度控制,湿度显示、直观了然,外形美观,性能优越,操作简便。

2.控制系统说明本机控制模式说明如下:湿度显示:机器带有湿度显示功能,显示当前环境湿度状况。

开关键: 机器使用薄膜式开关,第一次按键为开机,再次按键为关机。

湿度设定:机器设有湿度设定功能,+为湿度设定增大,-为湿度设定减小。

定时化霜设定:为了发挥本设备的最佳效果,延长设备的使用寿命,正常情况下请设定定时化霜时间.夏季设定40分钟,冬季设定30分钟.设定时先按设定键,再按+\-设定所需时间即可.3.工作原理说明:除湿机工作系统分为二部分制冷循环部分由压缩机、冷凝器、毛细管、套管式冷凝器及连接管道组成,低压制冷剂气体由压缩机吸入,压缩成高压气体,进入冷凝器并放出热量,经冷凝器冷却成液体,然后经过过滤器毛细管节流成为低压低温的气体混合物进入套管式冷凝器,由蒸发器蒸发为气体,吸收空气中的热量,再回到压缩机。

制冷剂工质在制冷系统内这样反复循环,达到制冷的目的。

空气循环部分湿空气由离心风机吸入并通过空气过滤网进入蒸发器,当蒸发器的表面温度底于空气的露点温度时空气被冷却,空气中含有水分就会被凝聚下来,被冷却除湿后的空气继续前进,进入冷凝器并带走冷凝器释放出的热量,由离心风机送出,使空气中的相对湿度降低。

空气如此不断循环,其中含有的水分不断被冷却凝聚下来,达到除湿的目的五、设备安装1.电源接线本机安装必须由专业电工安装,若无专业电工,可电话联系本公司指导安装。

本机使用380V/50HZ电源,三相四线,机身背面有接地标志,使用前务必做好接地线连接。

本机器装有断相与相序保护器,当外接三相电源与机器本身认定的相序不对时,相序保护器断开, 控制面板运行灯闪烁,但机器不运转,此时需要调整接入电源相序,重新再次开机,此操作需要专业电工操作。

不要以电源的插入或拔出方式来控制除湿机的运转或停止。

2.环境要求一般要求除湿机四周距离墙壁等障碍物600mm以上。

为了防止除湿机内部结露,机组不应该暴露在温度低于处理空气露点的环境中。

除湿机安装在通风的场所,应避开强电磁,油烟,风沙及灰尘较大的地方,且远离腐蚀性气体,及任何存在或可能存在可燃性气体和蒸气与空气混合形成的爆炸危险场所。

机组周围应设有排水装置,用于冷凝水的排除。

3.基础要求当除湿机安装后,应检查设备安装是否处于水平状态。

电气连接必须由有电工资格的专业人员执行。

六、设备开机检查事项1.电源线检查确定电源电压为380V,50Hz。

确定相序接对,本机设有相序保护,当相序接错时本机开机相序指示灯亮表示相序错误,需重新调整相序,才可开机。

不要以电源插入或拔出的方式来控制水冷除湿机的运转或停止。

请务必使用接地。

2.工作模式检查检查机器有没有不正常的声音。

3.风机状态检查当将室外空气引入除湿机时,进风口应离地面有足够的高度以防止尘土和碎片的侵入,入口必须远离可能污染的污染源。

此外,风机口必须有防止雨水漏进的设施。

七、设备操作规程1.湿度控制面板说明湿度显示: 本机带有湿度显示功能,显示当前环境温湿度状况。

湿度设定:机器设有湿度设定功能,+为湿度设定值增大,-为湿度设定值减小。

工作模式说明: 机器故障(状态)提示: 当温度传感器和湿度传感器异常时,控制面板显示(E1为温度传感器故障,E2为湿度传感器故障).传感器故障排除后,机器显示回复正常。

湿度设定机器设有湿度显示功能, 显示当前环境湿度状况, 湿度设定“+”为湿度设定值增大, “-”为湿度设定值减小。

机器开关机器使用薄膜式开关, 第一次按键为开机, 再次按键为关机。

(本机设有三分钟延时保护功能,关机后需等3分钟才能重新开机,在延时保护时间内运行灯闪烁,压缩机不工作,风机工作。

)设定:为了发挥本设备的最佳效果,延长设备的使用寿命,正常情况下请设定定时化霜时间.夏季设定40分钟,冬季设定30分钟.设定时先按设定键,再按+\-设定所需时间即可.检查机器开机工作状态机器的放置是否处于水平面。

检查给水是否畅通,电源是否正常。

机器关机停止使用时,请先关掉开关,然后拔掉电源。

除湿机操作面板●按键功能说明1、“开/关”键开机时按该键,蜂鸣器响两声,进入开机模式关机时按该键,蜂鸣器响一声,进入关机模式2、“+”键直接按此键可对设定湿度进行加操作,每按一次蜂鸣器响一声,设定湿度增1%RH,连续按住可对设定键湿度进行连续加操作;当按“定时/时钟”键后再按该键是对时间(小时)进行加操作。

3、“-”键直接按此键可对设定湿度进行减操作,每按一次蜂鸣器响一声,设定湿度减1%RH,连续按住可对设定键湿度进行连续减速操作;当按“定时/时钟”键后再按该键是对时间(分钟)进行减操作。

4、定时设定时先按设定键,再按“+”或者“-”设定所需时间即可.●开机1、开启电源,除湿机发出“嘀”一声;2、按一下“开/关”键,LCD显示窗亮,所有显示正常后,LCD显示窗显示当前环境湿度;3、湿度设定:按动湿度增或湿度减键来调整您所需的湿度,当设定湿度小于当前湿度3%时,除湿机工作。

当设定湿度大于当前湿度3%时,除湿机停止工作。

注意事项:1、如果设定湿度高于实际湿度,除湿机将不会工作。

2、进行除湿时,压缩机开始工作后,风机和压缩机至少运行3分钟才能停止工作;压缩机停止工作后,必须经过3分钟压缩机才能启动。

3、如在较低湿度下工作,除湿机会自动判断系统湿度,从而达到自动除霜的目的;除霜时,除霜指示灯亮,风机工作,压缩机自动停止工作。

4、系统具备自动记忆功能,当所有模式设定完成后,当系统在工作中突然遇到停电,电源插头没有插紧滑落,系统可在断电前自动存储当前运行状态,在下一次上电时系统将自动进入断电前的运行模式。

5、湿度可以设定范围为30%—90%。

6、若长时间不使用除显机,请卸下电源线或断电。

7、CF20K机器采用双压缩机结构,开机运行时压缩机A先启动,15秒后压缩机B启动。

8、CFZ-7S、、CFZ-10S、CFZ-15S、CFZ-20S、CFZ-30S、CFZ-35S、CFZ-40S七款除湿机使用电源为380V/50HZ,具有相序或缺相时,控制面版中的所有按键不起作用,当外接三相电源和机器认定的相序不对应或缺相时,控制面版中的所有按键不起作用,湿度显示窗显示“E3”,此时需调整电源相序或检查电源,重新开机。

9、自动检测温/湿度传感器故障:(1)当系统检测到温度传感器超出其有限范围时,系统进入温度传感器故障模式,该模式下LCD显示温度故障代码“E1”,系统以30分钟内除湿运行,15分钟化霜运行进行循环工作;(2)当系统检测到湿度传感器超出其有限范围时,系统进入湿度传感器故障模式,该模式下LCD显示温度故障代码“E2”,系统进入连续除湿运行;(3)当温/湿度传感器故障排出后系统进入正常运行。

八、产品日常维护A.每周维护事项清洗空气过滤网空气过滤网积累灰尘,会影响除湿机效果,甚至会发生故障,必须定期清洗,清洗时间为每周甚至每天清洗一次。

拆下前面盖板,清洗过滤网,清洗时可轻敲过滤网或用吸尘器除去过滤网上的灰尘,或将过滤网放入温水(≤40℃并加少量中性洗涤剂)中洗刷,并用清水冲洗后晒干。

注意高低压表,是否达到要求。

B.每月维护事项应测量电压等参数是否正常。

C.每季度维护事项检查线路是否老化。

★注意:1.过滤网不能直晒或火烤,以免变形。

2.除湿机开机前应装上过滤网。

3.在维护之前必须切断电源.九、常见故障分析及排除方法十、故障代码说明本除湿机具有自动判断故障功能,如出现故障,湿度显示窗中会出现故障代码。

故障代码:。

相关文档
最新文档