dell服务器错误代码

E1414
E1418
CPU # Presence High CPU Mismatch High CPU Protocol
E141C
E141F
High
E1420
CPU Bus PERR High
E1421
E1422
CPU Init High CPU MachineC hk High
System Memory - Message Code: "x21xx" Message Message Message Code String Priority MBECrdx DIMM ## E2110 & ## High SBE Log DisableCr E2111 dx DIMM High MemSpar eCrdx E2112 DIMM ## High Mem Mirror Crd E2113 x DIMM High
Memory VTT voltage regulator has failed.
Processor # VCORE voltage regulator has failed.
Processor VTT voltage regulator has failed.
0.9 V regulator voltage has exceeded the allowable voltage range.
High
High
High
High
Fans - Message Code: "x13xx" Message Message Message Code String Priority RPM Fan ## Low RPM Fan Mod #A Low RPM Fan Mod #B Low RPM Fan Mod #C Low RPM Fan Mod #D Low Fan Redunda ncy Low
BIOS has reported a machine check error.
ssage Code: "x21xx"
Message Comments One of the DIMMs in the set implicated by "## & ##" has had a multi-bit error (MBE).If no memory riser is present the “Crdx” string is left out of the message.“x” is the memory riser, A-Z. BIOS has disabled memory single-bit error (SBE) logging and will not log anymore SBEE's until the system is rebooted.## represents DIMM implicated by BIOS .If no memory riser is present the “Crd x” string is left out of the message.“x” is the memory riser, A-Z. BIOS has spared the memory because it has determined the memory had too many errors.## represents DIMM implicated by BIOS. If no memory riser is present the “Crdx” string is left out of the message.“x” is the memory riser, A-Z. BIOS has disabled memory mirroring because it has determined one half of the mirror has had too many errors. ## & ## represents DIMM pair implicated by BIOS. If no memory riser is present the “Crdx” string is left out of the message.“x” is the memory riser, A-Z.
E1211
W1228
E1214
High
E1215
High
E1216
High
E1217
5VPwrGd High PCIRsr5V PwrGd High Backplan ePwrGd High Flex BayPwrG d High VCACHE #PwrGd High VRM #PwrGd ESB 1.5VPwr Gd
Backplane voltage regulator has failed.
Flex Bay voltage regulator power good has failed.
VCACHE # voltage regulator has failed.
VRM # voltage regulator has failed.
Ambient temperature has a reached a point outside of the allowed range. Memory has exceeded allowable temperature and has been disabled to prevent damage to the components.
A voltage regulator failure was detected when the processor regulator(s) was enabled.
e: "x13xx"
Message Comments
RPM of fan ## is outside of the intended operating range.
Message Comments Processor # has had an internal error (IERR), but this does not always mean that CPU is the problem .There are a large variety of issues that cause an IERR.
E1114
Med
E1116
High
Voltages - Message Code: "x12xx" Message Message Message Code String Priority
E1210
CMOSBat t Low ROMBBat t Low ROMBBat t< 24 hr Low 1.5VPwr Gd 1.8VPwr Gd 3.3VPwr Gd
BIOS has reported a processor protocol error.
BIOS has reported a processor bus PERR (parity error).
BIOS has reported a processor initialization error.
Cable and Board Presence - Message Code: "x1Axx" Message Message Message Code String Priority PDBPwrC able High PCIRsrCo nfig High PCIRsrMi ssing High SAS Cable A SAS Cable B
Processor # has encountered a Thermtrip(over-temperature) event.
Processor # is missing/bad and the system is in an unsupported configuration.
Processors are not compatible as defined by Dell .System is in an unsupported configuration.
Code: "x12xx"
Message Comments
CMOS battery is missing or the voltage is outside of the allowable range. PERC5I RAID battery charger has reported to the Server Management that the battery is either missing, can't charge the battery (possibly because of high temperatures), or the battery is bad. This is a predictive failure warning message telling the user that the PERC5I RAID battery has less then 24 hours of charge left init. We provide this message as a warning message to the customer.
Same as above except for fan D of module #. The system is no longer fan redundant. Another fan failure would put the system at risk of overheating.
e Code: "x14xx"
Flex bay power cable is missing or bad.
PDB control cable to the planar is missing or bad and system will not power on.
age Code: "x11xx"
Message Comments
ESB 1.5 VV voltage regulator has failed.
PCI Riser 1.5 VV voltage regulator has failed. Linear voltage regulator(s) has failed. Represents status of multiple voltage regulators used in the video and LOM circuitry.
1.5 VV voltage regulator has failed.
1.8 VV voltage regulator has failed.
3.3 V voltage regulator has failed.
5 V voltage regulator has failed.
PCI Riser 5 V voltage regulator has failed.
One or all of the PCI risers is missing. This prevents system power on.
SAS cable A is missing or bad.
SAS cable B is missing or bad.
Flex bay SAS cable is missing or bad.
RPM of fan A in the # module is outside of the intended operating range.
Same as above except for fan B of module #.
Same as above except for fan C of module #.
E1218
E1219
E1221
E1222
E1223
High
E1225
High
E1226
PCIRsr1. 5VPwrGd High LinearPwr Gd High 0.9VPwr Gd
E1227
ຫໍສະໝຸດ BaiduE1228
High
E1229
E122A
E122B
E122C
CPU # VCORE CPU VTTPwrG d 0.9 V Over Voltage CPU Power Fault
E1310
E1311
E1311
E1311
E1311
E1313
Processors - Message Code: "x14xx" Message Message Message Code String Priority CPU # IERR High CPU #Thermtri p High
E1410
I2114
MemRaid Low MemAdd ed Card x Low MemRem oved Low MemHot Plug
I2115
I2116
E2117
Low
E2118
E2119
Fatal NBMemC RC High Fatal SBMemC RC High
sence - Message Code: "x1Axx"
E1A10
E1A11
E1A12
E1A14
Low
E1A15
Low
E1A16
SAS Cable FB Low PwrCable FB Low PDBCtrl Cable
E1A17
E1A18
High
Temperature - Message Code: "x11xx" Message Message Message Code String Priority Temp Ambient Temp Memory
Message Comments
PDB power cable to the planar is missing or bad and system will not power on.
PCI risers are not configured correctly; some invalid configurations prevent system power on.