电梯专业词汇

电梯专业英语词汇
abbreviation 缩语
abnormal "不正常的,反常的"
abnormality monitoring 异常监听
abrasion 磨损
abrasion resistant 耐磨性
abrasive cloth 砂布
absorb 吸收
absorber 减振器
AC drive 交流拖动
AC feedback control 交流反馈控制
AC motor 交流电机
AC servo 交流伺服
AC servo motor 交流伺服电机
AC single speed 交流单速
AC two speed 交流双速
AC two speed motor 交流双速电动机
AC variale speed 交流调速
AC(alternating current) 交流电
acanning cycle 扫描周期，扫描循环
acceleration control system 加速度控制系统acceleration(accel)rate 加速器
accelerator 加速器
acceptance of lift 电梯验收
acceptance period 验收阶段
acceptance test 验收试验
acceptanec certificate 验收证书
access door 检修门
access forbidden 禁止入内
access lift 通道电梯
access security 通道防卫
access switch "通道开关,维修用开关"
access way 进出通道
accessibility "可通达性,接近的,难易程度"
accessible 允许进入
accessible space 允许进入的场地
accessory "配件,附件"
accident 事故
accident insurance 事故保险
accident prevention 事故预防
accidental contact 触电
accidental operation 误操作
accordion door 折叠门
accumulation 累积
accumulator 蓄电池
AC-GL machine 交流无齿曳引机
acoustic "听觉的,声音的"
acrew die 板牙
activate "启动,触发"
active mode 主动模式
actual condition "实际状况,实际条件" actual load 实际载荷
actual state 实际状况
actual value 实际值
actuate "开动,操作,激励"
actuating linkege 操作连杆
actuating magnet 操作磁铁
actuation time 动作时间
actuator "操纵机构,激励器,螺线管" actuator bracket 调节器支架
actuator plate 调节板
ACVF drive 交流调频拖动
ACVF system 交流调频系统
ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动
ACVV system 交流调压系统
ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"
adapter PCB 选通脉冲印刷电路板
adapter(adapator) 适配器
adapting 选配
adaptive control system 自适应能力控制系统addendum "齿顶高,附录"
addendum circle 外圆
adding working drawing 附加加工图addition "附加物,加法"
additional materials 附加材料
address 地址
adhesion "胶,粘合胶"
adhesion protective oil 防粘油
adhesive foil 胶粘薄膜
adhesive tape 胶带
adjacent 邻近的
adjacent car "相邻轿厢,相邻电梯" adjacent entrance 相邻出入口
adjusment 调试
adjustable condensor 可变电容器
adjustable resistance 可调电阻
adjustable spanner 可调扳手
adjustable speed electric drive 调速电力拖动adjustable wrench "活动扳手,可调扳手"
adjusting screw 调节螺丝
adjustor 调试员
administation overjhead rate 管理费用标准administration cost 管理成本
administration expenses 管理费用
advance door opening 提前开门
advance payment 预付款
advanced "提前的,先进的"
advanced carriage 超前拖板(选层器)
advancing position reference value 超前位置参考值aerial cableway "空中缆车,架空索道"
aerial ropeway "空中缆车,架空索道"
aerial tramway "空中缆车,架空索道"
aesthetic 美观
after sales service 售后服务
agency 代理
agenda 议程
air cord (门机用)航空钢丝绳
air purifier 空气滤清剂
air ventilator 通风管
air-bleed 空气分泄器
airborne noise 空气传播噪声
air-condition 空调
air-gap 气隙
alarm 警报
alarm bell 警铃
alarm button 警铃按钮
alarm buzzer 警报蜂鸣器
alarm circuit 警报电路
alarm system 警报系统
ALC(autoclaved light-weight concrete) 蒸压轻质混凝土alcove arrangement 电梯U型排列法
algorithm 算法规则系统
align 校正
aligning template 校正样板
alignment 校正
alignment gauge 校正量规
alkali 碱
all-computer-controlled 计算机全控的
allocation "分配,分派"
allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"
allowble stress for temporary load 允许暂时应力值alloy 合金
alloy steel 合金钢
alteration 改进
alternate floor 隔层
alumina 氧化铝
aluminum 铝
aluminum alloy 铝合金
aluminum bronze 铝青铜
aluminum cladding 铝制包层
alumite 防蚀铝
alundum 氧化铝
ambient 环境的
ambient noise 环境噪音
ambient temperature 环境温度
ammeter 安培计
ammonia 氨
amperage 电流强度
ampere 安培
amplification 放大
amplification stage 放大等级
amplifier 放大器
amplifying tube 放大管
amplitude 幅度
analog adder 模拟加法器
analog computer 模拟计算机
analog speed card 模拟曲线板
analog-digital converter 模拟-数字转换器analogue(analog) 模拟
analysis 分析
analysis mode 分析模拟
anchor bolt 地脚螺栓
anchorage "锚具,锚定"
angle bar 角钢
angle guide 角铁导轨
angle iron 角铁
angle iron frame 角铁框架
angle of contact 接触角
angle of deflection 导向角
angle of inclination 倾斜角
angle of lead 导程角
angle of traction 曳引机包角
angle of wrap 包角
angle steel 角钢
angular contact ball bearing 向心推力球轴承
angular contact bearing 角面接触滚动轴承
angular gear 斜齿轮
angular retardationg 角减速度
angular velocity 角速度
anneal 退火
annealing 退火
annual inspection 年检
annual report 年度报告
annunciator "报音器,声音合成器"
anode 阳极
anodize 氧极氧化
ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向
anti-corrosive paint 防腐蚀漆
anti-creep 防蠕动
anti-friction bearing 抗摩擦轴承
anti-nuisance 防干扰
anti-nuisance device 防捣乱装置
anti-phase braking 反向制动
anti-phase current 反相电流
anti-rebound of compensation rope device 补偿绳防跳装置anti-residual 防剩磁
anti-resonance 抗谐振
anti-reversion device 防反转装置
anti-rust 防锈
anti-stall 防空转
anti-vibralion pad 防震垫
APM(automatic people mover) 自动人员运输机
apparen power 视在功率
apparent output 视在输出
applicant 申请人
application 申请
application guide 应用指南
aprons 裙板
arbour "轴,杆"
arc chamber 电弧隔离室
arc protection 防电弧
arc quenching 熄焊弧
arc shield 电弧屏蔽
arc suppressor 灭焊器
architect 设计单位
architecture 建筑学
architrave 门框
area 面积
arm "臂,支路"
armature 电驱
armature coil 电驱线圈
armature current 电驱电流
armature lamination 电驱铁芯片
armature shaft 电驱轴
armature spider 星形轮
armature winding 电驱绕组
armoured 蛇皮管的
armoured cable 蛇皮管电缆
armoured conduit 导线管
arrangement 布置
arrival bell 到站铃
arrival buzer 到站蜂鸣器
arrival floor 到达楼层
arrival gong 到站钟
arrival rate 到站率
article of consumption 消耗品
artificial intelligence 人工智能
artistic 工艺
artistic face 工艺表面
asbestos packing 石棉盘根
ascending 上升
ASIC(application specific integrated circuit) 专用集成电路assemble 装配
assembler language 汇编语言
assembly of hinge 铰链组装
assign 分配
astragal 装饰镶条
atmospheric influence 大气影响
attachment 附件
attendant control 有司机控制
attendant control compartment 有司机控制盒
attendant operation 有司机操作
audible signal 音响信号
audio tape recording 磁带录音
authority "当局,核准部门"
authority of lift acceptance 电梯验收部门
authorized "授权的,核准的"
authorized user 核准使用者
auto-adaptation 自适用
AutoCAD 自动计算机辅助设计
autographic recoder 自动记录仪
automatic 自动的
automatic allocator 自动分派器
automatic by-pass 自动直驶
automatic center opening sliding door 自动中分式滑动门
automatic closer 自动关闭门
automatic dispatch 自动调度
automatic door 自动门
automatic homing 自动回基层
automatic landing 自动停站
automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层
automatic lubricator 自动润滑装置
automatic parking garage 自动停车库
automatic parking system 自动停车系统
automatic relevelling 自动平层校正
automatic rescue device 应急救助装置
automatic return 自动返回
automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门
automobile lift 汽车电梯
autowalk 自动人行道
auxiliary apparatus 辅助装置
auxiliary brake 辅助制动器
auxiliary cicuit 辅助电路
auxiliary contact 辅助触点
auxiliary drive 辅助驱动
auxiliary lock 辅助锁
auxiliary materials 辅助量
auxiliary value 辅助材料
auxiliary winding 辅助绕组
available area 有效面积
average 平均
average car load 平均轿厢负载
average dispatching interval 平均调度间隔时间
average interval 平均调度间隔时间
average passenger waiting time 平均乘客侯梯时间
average response time 平均应答时间
average waiting quest 平均乘客量
average waiting time 平均乘客侯梯时间
axial flow fan 轴流式风扇
axis 轴线
axle 轴
babbit 巴氏合金
babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器
babbit metal 巴氏合金
babbit rope socket 灌注式巴氏合金绳头back current 反向电流
back e.m.f 反电动势
back lash 轮齿隙
back plunger type 后部柱塞式(液压梯) back side "后侧,后边"
back type governor 轴流式限速器back wall 后壁
baked enamel 烤漆
balace weight 平衡器
balance 平衡
balance chain 平衡链
balance coefficient 平衡系数balanced traffic 平衡交通
ball bearing 滚珠轴承
ball cup 球形碗
ball pin 球形硝
ball stop valve 球形断流器
ball type bearing 滚珠轴承
ballast 镇流器
balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板
balustrade skirting 扶手群板balustrades 扶手装置
bandsaw 带锯
bank "银行,群组,排"
bar "条,棒"
bar code 条形码
bar lock 杆式锁
bare wire 裸线
barricade "防护墙,隔墙"
barrier "隔板,栅栏"
base "基座,基础"
base plate 基板
basement 地下室
basement service 底下室服务
basement type 底吊式
basic logic element 基础逻辑元件
basic logic function 基础逻辑功能
batch production 批量生产
battery 电池
battery- backed 电池支持的
battery box 蓄电池箱
battery charger 电池充电器
baud rate 波特率
BCD(binary coded decimal) 二进制编码的十进制beam 梁
beam pad 井道内电缆保护垫片
beam pulley 抗绳轮
bearing 轴承
bearing bracket 轴承支架
bearing cap 轴承盖
bearing load 轴承负荷
bearing plate 承重板
bearing play 轴承间隙
bearing sleeve 轴承衬套
bearing stand 轴承座
bed lift 病床电梯
bed plate 底座
bell 铃
belt 胶带
belt drive 胶带传动
belt grinder 胶带磨床
belt pulley 胶带轮
belt type moving walk 带式自动人行道bending 弯曲
bending stress 弯曲应力
benzine 轻汽油
bevel gear 伞(斜)齿轮
beveled washer 斜垫圈
BGM (background music) 背景音乐
BGM speaker 背景音乐扬声器
bias "偏置,偏移"
bid "投标,报价"
bid table 报价单
bidder 投标
bidding cycle 投标有效期限
bidding procedure 投标(报价)程序
bil of delivery 发货单
bil of lading 海运提单
bill of expenses 费用帐单
bill of materials 材料单
billing 开发票
binary 二进制
binder 装订册
bi-parting 对开式(上下开启)
bi-parting door 垂直中分门
bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关
bitumen 沥青
blade "叶片,刀片,锯片"
blade connector 刀形连接器
bleed-off circuit 泄放电路
blind hoistway 盲(无门)井道
block chart 方框图
block diagram 方框图线路
block of flats 住宅楼区
blocking of control circuit 控制电路闭锁blower 鼓风机
blower coil 吹弧线圈
blower motor 风机电动机
blue print 蓝图
boading floor 登梯楼层
boading time 登梯时间
boarding 登梯
boarding landing 登梯层站
boarding passenger 登梯乘客boarding rate 登梯率
boarding stop 登梯停站
boarding zone 登梯区域
bobbing 绕线管
boldface type 粗字体
bolt 螺杆
booster 升压机
border condition 边界条件
bore hole "钻孔,镗孔"
boring 镗
boring lathe 镗床
boring machine 镗床
boring miller 镗铣床
bottom 底部
bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程
bottom car runby 底部轿厢越程
bottom clearances for car 轿底间隙
bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角
bottom floor 底部楼层
bottom runby 底部越程
bottom slow down switch 底部减速开关bottom stop 底部停战
bottom terminal floor 底部楼层
bottom terminal landing 底部端站
bottom terminal stop 底端停站
box "盒,箱"
box counterweight 箱式对重
Braille 盲文字符
brake 制动器
brake arm 制动器臂
brake contact 制动器触点
brake coutact 制动器联轴器
brake dish 制动盘
brake drum 制动轮
brake energy 制动力
brake level 制动器杠杆
brake lever 制动器手柄
brake lining 制动器衬套
brake linkage 制动器连杆
brake operater switch 制动操纵开关
brake pin 制动器悄
brake press "折弯机,压弯机"
brake pulley 制动轮
brake release lever 制动器松闸手柄
brake release magnet 制动器送闸磁铁
brake release time 制动器松闸时间
brake shoe 制动靴
brake spacing 制动器间距
brake spring 制动弹簧
brake tension 制动器张紧力
brake torque 制动器力矩
brake wrench 制动器板手
braking 制动
braking distance 制动距离
braking force 制动力
branch circuit 分支电路
brass founder 铸铜
break "切断,破断"
break-down 故障
breaking load 破断负荷
breaking strength 破断强度
breaking test 破坏实验
breather 通气管
brick 砖
brick-layer 砖砌工
bridge circuit 桥式电路
bridge connector 桥接器
bridge jumper 桥接片
bridge rectifier 桥式整流器
bright controlling 光度控制
broach 拉力
broaching machine 拉床
brochure 手册
broken chain contact 断链触点
broken circuit 断路
broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点
broken step chain device 断绳开关
broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关
bronze 铜
brunching "成组,成群"
brush finished stainless steel 哑光不锈钢
brush holder "刷握,滑环"
brush yoke 刷架
budget 预算
buffer 缓冲器
buffer base 缓冲器底座
buffer plate 缓冲器板
buffer plunger 缓冲器柱塞
buffer return spring 缓冲器复位弹簧
buffer stand 缓冲器台
buffer striking plate 缓冲器撞板
buffer stroke 缓冲器冲程
buffer support 缓冲器支承
buffer switch 缓冲器开关
buider's work drawing 土建图纸
buiding facility 大楼设施
buiding supervision center 大楼监管中心
builder 建筑单位
building 建筑
building area 建筑面积
building contractor 建筑承包商
building manager 大楼管理者
building monitoring and security system 大楼监管和安全系统building population 大楼居住人口
built=in 内装
built-in escalator 组合式自动扶梯
bumper 弹簧式缓冲器
bumper rail 防撞板
bumpy ride 颠簸振动的运行
buried 埋入的
burn in (程序)灌入
burr "毛刺,毛边"
burr free 去毛刺
bus 总线
bus bar 汇流条
bush 衬套
bushed bearing 加衬轴套
bushing "衬套,轴套,套筒"
butt joint "平接,对焊"
button 按钮
button switch 按钮开关
buyer 买方
buzzer 蜂鸣器
buzzer switch 蜂鸣器开关
bypass 直驶
by-pass button 直驶按钮
by-pass valve 溢流阀
bypassed floor 直驶不停楼层
bypassed stop 直驶不停层站
C$F 到岸价
cab "轿厢,座舱"
cab interior 轿厢内部
cabin "轿厢,座舱"
cabinet "柜,厢"
cable 电缆
cable box 电缆箱
cable car 缆车
cable cleat 电缆夹具
cable conductor 电缆导线
cable entry 电缆引入
cable hanger 电缆吊架
cable hole 电缆孔
cable joint 电缆接头
cable termination 电缆末端
cable trunk 电缆接头
CAD 计算机辅助设计
cage 轿厢
cage door 轿厢门
calculation 计算机辅助设计
calibrate 校准
call "呼梯,呼叫"
call acceptance 呼梯接收
call accepted 接受呼梯
call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号
call allocation 呼梯分派
call assignment 呼梯指令分配
call band 呼梯信号带
call button 呼梯按钮
call cancel 呼梯取消
call canceling 呼梯取消
call coincidence 呼梯重合
call conmting system 呼梯计数系统
call contrl 呼梯指令控制
call emitter 呼梯指令发送器
call input 呼梯输入
call input capacity 呼梯输入内容
call input device 呼梯输入装置
call load 呼梯输入
call memory 呼梯记忆
call registered 登陆的呼梯
call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序
call tegistration 呼梯登陆
call-back 召修
call-back message 召修信息
callinfg board 召唤盒
calling floor 呼体楼层
calling landing 呼梯
call-out response time 维修召唤应答时间call-out service 急修服务
CAM 计算机辅助制造
cam 凸轮
cam for positive operation 强制操纵凸轮
cam lever 偏心柄
cam shaft 偏心轴
cam tape control 偏心带控制
cam-gear 凸轮传动装置
cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"
cancelingof call signal 呼梯信号消除cancellation "撤消,取消"
canopy "顶盖,大蓬"
canvas 帆布
canvas hose 帆布软管
cap "帽,盖子"
cap nut 螺母
capacitance "电容,电容量"
capacitor 电容
capacitor motor 电容器电机
capacity "载重,容量,定员"
capacity plate 载量标牌
capstan 绞盘
captive roller safety gear 滚柱式安全钳
car 轿厢
car annunciator 轿厢报警器
car approaching gong 轿厢到站预报钟
car apron 轿厢入口群板
car assignment "轿厢调度,轿厢分配"
car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线
car back wall 轿厢后壁
car botom clearance 轿厢安全高度
car bottom overtravel 轿厢底部越层
car bottom runby 底部越程
car buffer 轿厢缓冲器
car button 轿厢按钮
car cab 轿厢体
car call 轿厢指令
car call button 轿厢指令按钮
car call cancel 轿内召唤取消
car call control 轿厢指令控制
car call panel 轿厢(呼梯)指示盘
car call stop 轿厢(呼梯)指令停车
car cam 碰铁
car canopy 轿厢顶盖
car coming indicator 轿厢驶近指示灯
car control lever 轿厢操纵手柄
car control switch 轿厢操纵开关
car counterweight 轿厢对重
car cross-head 轿厢上梁
car depth 轿厢深度
car dispatch 轿厢调度
car door 轿门
car door catch 轿门栓
car door closer 轿门关闭器
car door electric contact 轿门电触点
car door guide shoe 轿门导靴
car door interlock 轿门联锁
car door lock 轿门门锁
car door rail 轿门导轨
car door sill 轿门地坎
car door track 轿门导轨
car elevator 汽车电梯
car emergency exit "轿厢安全门,应急门"
car emergency opening 轿厢安全窗
car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板
car enclosures 轿厢壁板
car entrance 轿厢入口
car extetior "轿厢外装修,轿厢外表"
car fan 轿厢风扇
car floating movable platform 轿厢活动地板
car floor frame "轿厢架,轿架"
car frame "轿厢架,轿架"
car frame attachment 轿厢框架附件
car frame plank 轿厢下梁
car frame upright 轿厢立柱
car front 轿厢前壁
car full control 满载轿厢控制
car gate 轿厢门
car gate contact 轿门触点
car gate electric contact 轿门电气触点
car guide 轿厢导轨
car guide axis 轿厢导轨中心线
car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手
car height 轿厢高度
car illumination 轿厢照明
car leveling device 轿厢平层装置
car lift 汽车电梯
car light 轿厢照明装置
car light panel "轿厢照明板,照明天花板"
car lighting 轿厢照明
car manual switch landing 轿厢手动开关停站
car operation board 轿厢操纵盘
car operation panel 操纵箱
car overload 轿厢超载
car panel 轿厢壁板
car panel attachment 轿厢壁板附件
car panel base 轿厢壁板底座
car panel with window 轿厢壁板上窗口
car platform "轿厢底,轿底"
car platform guard 轿厢站台护板
car platform sill 轿厢
car position indicator "轿厢指示灯,轿厢位置显示"
car position reference value 轿厢位置参考值
car preference 轿厢优先权
car push-button 轿厢按钮
car rear wall 轿厢后壁
car roof "轿厢顶,轿顶"
car safety 轿厢安全钳
car safety bar for dumbwaiter 轿厢安全棒(杂货梯)
car safety gear 轿厢安全钳
car safety mechanism switch 轿厢安全钳联动开关
car sheave 轿厢绳轮
car side emergency door 轿厢安全侧门
car side opening 轿厢侧面开门
car side wall 轿厢侧壁
car sill 轿厢地坎
car sling "轿厢架,吊架"
car station 轿厢操纵站
car status information 轿厢运行状态信息
car stop 轿厢停止
car suspension 轿厢悬挂装置
car switch 轿厢开关
car switch automatic floor stop operation 轿厢开关自动停站装置car switch control 轿厢开关控制
car switch opration "手柄开关操纵,轿内开关控制"
car top 轿厢顶部
car top clearance 轿顶安全高度
car top emergency exit "轿顶安全出口,轿顶应急出口"
car top guard 轿顶护栏
car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站) car top light 轿顶照明装置
car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风
car walls "轿厢壁,轿壁"
car weight 轿厢重量
car width 轿厢宽度
carbon "碳,石墨"
carbon brush 碳刷
carbon contact 碳精触点
carbon steel 碳素钢
carburization 渗碳
carburize 渗碳
carburized hardening 渗碳硬化carburizer 渗碳剂
card "卡片,纹板"
card reader 卡片读出器
cardan joint 万向接头
carpet 地毯
carriage charges 运费
carry frequency "载波频率,开关工作频率" carrying capacity "载运量,载运能力"
cart elevator 车辆运货电梯
cartridge fuse 插塞式熔断器
carving machine 刻模机
cascade "级联,串联"
cascade sub-loop 串接式子回路
case "箱,盒,外壳"
casing "保护套,外套"
casing of cylinder 油缸套
cassette tape 录音带
cast bronze 铸青铜
cast iron 铸铁
cast steel 铸钢
casting 铸造
castor oil 蓖麻油
catch "擎子,门扣,捕捉器"
catch block 安全钳
catch clip 捕捉夹钳
catch device 捕捉装置
cathode 阴极
cathode ray tube(CRT) 阴极射线管
cavitation "气穴,涡穴,饱和压力点"
ceiling 吊顶
ceiling assembling 轿顶
cellulose 纤维板
cement "水泥,胶合剂"
cement concrete 混凝土
cenrifugal brake 离心制动器
center 中心
center latch 中心门栓
center line 中心线
center of curvature 曲率中心
center opening 中分式门
center opening door 中分门
center opening two speed door 中分四扇门
center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑" center-opening folding door 中分式折叠门centigrade 摄氏温度
central alarm 中央报警
central control board 中央监控盘
central control room 中央监控室
central jack 中心液压装置
central position 中心位置
centrifugal 离心的
centrifugal cast 离心铸造
centrifugal fan 离心式风扇
centrifugal governor 离心式限速器
centrifugal speed 离心速度
centrifugal switch 离心开关
centrifugal type governor 离心式限速器
centripetal force 向心力
ceramic capacitor 搪瓷电容
certification 证书
certifying body 认证机关
chain 链条
chain block 手拉葫芦
chain bracket 链条托架
chain drive 链传动
chain drive elevator 链驱动升降机
chain drive machine 链驱动机
chain gear 链轮
chain guard 链防护罩
chain link "链节,链环"
chain pitch 链条节距
chain sag 链条下垂度
chain sheave 链轮
chain sprocket 链轮
chain sustarned elevator 链支撑升降机chain tensioning device 链张紧装置chain wheel 链轮
chain wheel track 链轮导轨chamger "倒棱,去毛刺"
change switch 转换开关
change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性
channel 槽钢
channel iron 槽铁
channel steel 槽钢
character "特征,字符" characteristic "特征,特性" characteristic curve 特性曲线
charge "充电,收费"
charged "带电,充电"
charging contactor 充电接触器charging set 充电
chart 图表
chart of accounts 成本图表
check valve 止逆阀
chequer(checker)plate 网纹钢板
chief engineer 总工程师
chime 音钟
chip 芯片
chipboard 木屑板
chisel 凿子
choke "扼流,截流,阻塞"
choke coil 扼流线圈
chopper 斩波器
chrome 铬
chuck 卡盘
CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土
circle "周期,圆"
circuit 电路
circuit breaker "断电器,断路器"
circuit diagram 电路图
circular pitch 周节
circulating pump 循环泵
circulation 循环
circumferential force 圆周力
circumferential speed 圆周速度
circumferential velocity 圆周速度
CL(center line) 中心线
clacking 盖板
cladding 装饰
clamp 夹
clamp ring "压制环,加紧环"
clamping jaw 夹钳
clamping sleeve 夹紧套桶
clamping strap 制动带
class of loading 灾荷种类
clear depth 净深度
clear dimension 净尺寸
clear door height 门净高度
clear door width 门净宽度
clear entrance to the car 轿厢入口净尺寸
clear height 净高
clear hoistway 井道净尺寸
clear width 净宽度
clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度
clearance top car 轿顶安全高度
clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板
clerance 间隙
clevis U型夹
client "客户,买主"
clip 钳夹
clockwise 顺时针的
close circuit 闭合电路
closed loop 闭环
closed position (门)关闭位置
closed position monitoring (门)关闭位置检测closed-loop control 闭环控制
closed-type motor 闭合式电动机
closer 关门器
closing force (门)关闭力
closing speed 门关闭速度
closing travel 门关闭运行
closing valve 切断阀
clutch 离合器
clutch component 离合器部件
clutch plate 离合器板
clutch release sleeve 离合器释放套管
clutch spring 离合器弹簧
CMOS 互补型金属氧化物(半导体)
CNC(computerized numric control) 计算机数控coast to stop 滑行停车
coating 涂层
coaxial cable 同轴电缆
cock 龙头
code "码,符号,规程,规范"
code of practice "实施规程,实用规程"
code word 代号文字
coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数
coefficient of friction 摩擦系数
coil "线圈,绕组"
coil case 线圈外壳
coiled spring 螺旋弹簧
coincidence memory 重合记忆
coinciding call 重合呼梯指令
cold cathode 冷阴极
collapsible door 栅栏门
collapsible gate "栅栏门,折叠式门"
collapsible type door 折叠式门
collar 环
collecting brush 集电刷
collecting ring 轴环
collection "收集,集合"
collective control 集中控制
collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选
collective selective control 集选控制
collector 集电路
collision switch 碰撞开关
color 颜色
colored starnless steel 彩色不锈钢
colorfast 不褪色的
colorless 无色的
column "柱,立柱"
comb contact 梳齿板安全装置
comb floor plate 梳齿板
comb light 梳齿灯
comb lighting 梳齿板照明
comb plate 梳齿板
comb plate contact 梳齿板触板
comb plate safety device 梳齿板安全装置
commutation 整流
commutator 换向环
commutator brush 整流子电刷
commutator lug 整流片
commutator metallic segment 金属整流器
compact 紧凑的
comparator 比较器
compartment "隔板,隔室"
compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器
compensating 补偿
compensating chain device 补偿链装置
compensating condensor 补偿电容器
compensating devece 补偿装置
compensating rope 补偿绳
compensating rope device 补偿绳装置
compensating rope hitch 补偿绳绳头板
compensating rope sheave 补偿绳轮
compensating rope socket 补偿绳绳头
compensating winding 补偿绳绕组
compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关
compensation chain 补偿链
compensation coil 补偿绳线圈
compensation rope 补偿绳
compensation sheave 补偿绳轮
competent "有资格的,胜任的"
competent personnel "有资格的人员,胜任的人员"
competitor system 竞争机制
component 部件
compound wind motor 复励电动机
compound wound 复绕
comprehensive 综合的
comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同" compressing spring 压缩弹簧
compression 压缩
compression switch 压缩开关
compressive stress 压应力
compressor 压缩器
compulogic system 电脑程序控制系统
computer 计算机
computer peripheral devices 计算机外围装置
computer simulation 计算机模拟
computing power 运算容量
concealed "隐蔽的,暗式"
concealed hinge 暗式链条
concentrated load 集中载荷
concentricity 同心性
conclusion of contract 合同成交
concrete 混凝土
concrete hoistway 混凝土井道
concrete machine block 混凝土机座
concrete wall 混凝土墙
condenser 电容器
condenser for power factor improvement 功率因素补偿电容condition 条件
condition of payment 付款条件
conditions of contract 合同条件
conducting wire 导线
conductive 导电的
conductor 导体
conduit 导线管
conduit fitting 导线管接头
cone roller bearing 滚锥轴承
conference room 会议室
conical brake 锥形制动器
conical pin 锥销
conicity 锥度
connect in series 串接
connecting piece 连接件
connecting rod "连杆,连接杆"
connection 连接
connection diagram of controller 控制柜连线图connector "接线柱,连接器"
conract specification "合同规定,合同明细表"
conract speed "合同速度,额定速度"
consecutively departing 依次派出的轿厢
console panel "控制柜,控制盘"
constant "恒定的,常数"
constant HP motor 功率恒定型电机
constant speed valve "比例控制阀,调速阀"
constant torque motor 力矩恒定型电机construction "安装,施工"
construction crane 建筑起重机
construction layout drawing 土建图construction platform "安装平台,施工平台" construction site "安装工地,施工工地" consultant "顾问,咨询机构"
consumption 消耗
contact 触点
contact angle 接触角
contact brace 触头撑条
contact burning 触头烧损
contact carrier 触头支架
contact control 有触点控制
contact control system 有触点控制系统
contact finger "接触指,滑触头"
contact forcibly actuated 强迫操动触头
contact holder 触头固定架
contact input 接触输入端
contact load 保证(额定)载荷
contact mat 触头垫片
contact normally closed 常闭触点
contact normally open 常开触点
contact pressure 触头压力
contact resistance 接触电阻
contactless 无触点
contactless control 无触点控制
contactless control system 无触点控制系统contactless switch 无触点开关
contactor 接触器
contents 内容
conter 计数器
continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关
contract "合同,契约,承包合同"
contract capacity "合同载重量,合同容量" contract load 合同负载
contract of indemnity 赔偿合同
contract party "合同方,合同当事人"
contract work system 合同制度
control 控制
control amplifier 调节放大器
control bus 控制总线
control cabinet 控制柜
control cable 控制电缆
control circuit 控制电路
control device for handrail brekage 扶手带断带保护装置control feature 控制特征
control gear 控制论
control guard for handrail breakage 扶手带断带保护装置control lever 控制杆
control panel 控制屏
control stand 控制台
control station 控制站
control switgh 控制开关
control system 控制系统
control system for elevator 电梯控制系统
control technique 控制技术
control type 控制形式
control valve 控制阀
control valve unit (液压)调节阀装置
control voltage "控制电压,操作电压"
controlled angle 控制角
controller 控制柜
controller base 控制柜底座
controller cabinet 控制柜
controller panel 控制屏
controller wiring diagram 控制柜电路图
controlling circuit 控制电路
conuter-clockwise 逆时针方向
conventional 常规的
conventional lift 普通电梯
converter "整流器,转换头"
converter panel 换流器盘
converter set 换流器组件
converter unit 换流装置
conveyance of passengers 乘客载运
conveyer 输送机
conveyer track 输送车轨道
cooler 冷却装置
cooler air-conditioner 空调制冷
cooling 冷却
cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇
COP(car operation panel) 轿厢操纵盘
copper 铜。