单红椭圆灯规格书

NAN CHANG VISION TECH ELECTONIC CO.,LTD产 品 规 格PRODUCTS SPECIFICATION SHEET客户承认栏： 检查/Checked by 批准/Approved by 承认/Released by南昌宇欣科技有限公司 电话: + 86-791-8171817传真: + 86-791-8171572客户(CUSTOMER ):规 格(P/N ): Φ5红色椭圆 型号(MODEL)： LURAD0B220T 名称(NAME)： Φ5红色椭圆发光管NAN CHANG VISION TECH ELECTONIC CO.,LTD一、产品名称Product Name：红色椭圆发光二极管二、规格型号Model： LURAD0B220T三、用途Applications：⏹用于户外屏及亚户外屏的制作四、特点Features：⏹发光亮度高、发光颜色一致性好⏹高可靠性High reliability⏹低工作电压Low operating voltage⏹低功耗，长寿命Low power consumption，long life⏹环氧树脂红色散色封装Red diffused epoxy package五、封装外形图Outline Dimension (unit: mm)未标公差±0.1mmNAN CHANG VISION TECH ELECTONIC CO.,LTD 六、极限参数 Maximum ratings(Ta=25℃)参数parameter符号symbol额定值rating单位unit正向电流 forward current I FM40 mA 反向电压 reverse voltage V R 5 V 耗散功率 power consumption P M100 mw 工作温度 operating temperature range Top –40~85 °C 储存温度 storage temperature range Tstg –45~100 °C 焊接温度 soldering temperature * Tsol 260 °C *焊接位置离管体≥2mm,时间≤3秒（up to 2mm from the body of the device,t≤3s)七、光电参数Electro-optical Characteristics(Ta=25°C)参数parameter符号symbol测试条件Testcondition最小值Min.额定值Typ.最大值Max.单位Unit正向电压forward voltageV F I F=20mA -- 2.1 2.2 V 反向电流reverse currentI R V R=5V -- -- 5 μA 发光强度axial radiand intensityI E I F=20mA -- 500 -- mcd 峰值波长peak emittingwavelengthλp I F=20mA -- 626 -- nm光谱半宽度spectral line half width⊿λI F=20mA -- 20 -- nm半值角Value angle of halfintensityθI F=20mA -- 100 -- °NAN CHANG VISION TECH ELECTONIC CO.,LTD结电容CapacitanceCtf=1.0MHz--25--pF八、相关曲线图Optical-Electrical Characteristics1.2 1.0 0.8 0.6 0.4 0.2 00 10 20 30 40 50 60 70 80 90 1001000 100 10I F – F o r w a r d C u r r e n t (m A ) 0 1 2 3 4V F – Forward Voltage (V)正向电压 VS. 正向电流t P = 100 µst P /T = 0.0011000 10010.11 10 100 1000I e – R a d i a n t I n t e n s i t y (m W /s r )I F – Forward Current (mA)发光功率 VS. 正向电流 I e , r e l – R e l a t i v e R a d i a n t I n t e n s i t yT amb – Ambient Temperature (°C)I F – F o r w a r d C u r r e n t (m A )0 10 20 30 40 50 60 70 80 90 100R thJA200 175 150 125 100 75 50 25 0R thJA300 250 200 150 100 50 0 P V – P o w e r D i s s i p a t i o n (m W )T amb – Ambient Temperature (°C)NAN CHANG VISION TECH ELECTONIC CO.,LTD九、水平指向性Far Field Pattern十、使用注意事项Precautions①焊接条件Soldering Conditions●请在离树脂底部2mm 以上进行焊接。

Do solder in the lead frame about 2mm off the bottom of the resin. ●烙铁：请在30W 以下3秒内进行1次焊接。

Solder with iron: Do one time solder below 30W between 3 seconds. ●请避免树脂部分浸入锡槽。

Do not immerge the resin to the soldering stove. ●浸焊后请避免矫正位置。

Do not adjust the products position after soldered. ●焊接时在引线架被加热的状态下请不要施加压力。

Do not put any stress to the lead frame when it is heated in soldering.570 590 610 630 670λ – Wavelength (nm)发光功率比例 VS. 波长NAN CHANG VISION TECH ELECTONIC CO.,LTD②引线架的成型及切割Lead forming and cutting●成型位置请在卡点以下部分进行。

Do Lead form below the tie bar cutting position.●成型时请不要向封装外壳内部施加压力。

Do not stress the resin case when forming the lead.●成型时请在焊接前进行。

Do lead form before soldering.●产品在高温的状态下进行引脚裁切会对元件造成损害，请在常温下进行引脚裁切。

Cutting the lead frame at high temperature may cause problems. Do cut the lead frame at the room temperature.③安装Assembly●请不要在引线架施加压力的状态下安装。

Do not put any stress to the lead frame while assembling.●在电路板上安装时，安装孔距请与引线架保持一致。

When mounting products onto boards such as printed wired boards, the pitch between the two holes of such boards must the pitch of the products.④防静电Electrostatic protecting●本产品是对静电敏感的产品，在使用上需要十分注意。

特别是在超过最大额定的电流和电压时会损害或破坏产品。

在使用产品时请做好安全的静电和电涌防护措施。

These products are so sensitive to the static electricity that it need much care when in used. Particularly an over-current and over-voltage may cause damage to the products. Customer is requested to take adequate countermeasures to against static electricity charge and surge when handling the products.●检查通电电路，电流开关时的电涌不要超过最大额定电流，对于驱动电路清插入适当的保护电路。

A protection device must be installed in the driving circuit, which dose notexceed the maximum rating for surge current during on/off switching.●作为使用中的静电和电涌的措施，人体接地（通过1M欧姆），导电性垫子，导电性工作服，导电性鞋和导电性容器都是比较有效果的。

Proper grounding of products (Via 1 MΩ)， use of conductive mat, semiconducting working uniform and shoes, and semiconducting containers are considered to be effective as countermeasures against static electricity and surge.NAN CHANG VISION TECH ELECTONIC CO.,LTD●带电的产品与低电阻的金属表面等接触时由于急剧的放电现象所引发障碍得危险性变高。

工作台等于产品接触部分请用导电性垫子等通过电阻部分接地。

When the electrified product touches the low resistance part such as the metal face, these is a high possibility that it may be charge due to radical electric discharge. When grinding ,use of resisting element such as conductive mat is effective for parts where the product directly touches.●烙铁的尖端请注意接地。