海尔电热水器说明书ES60H-T1

合集下载

海尔 ES60H-GD1(1) 60升健康抑菌横式电热水器使用说明书

热水器使用说明书型号ES60H-GD1(1)• 本说明书为通用手册• 本公司保留说明书解释权• 产品外观请以实物为准• 阅后请与发票一并妥善保存• 如遇产品技术或软件升级，恕不另行通知• 本产品只适合在中国大陆销售和使用1. 产品介绍1 1.1. 产品部件1 1.1.1. 外观及部件介绍1 1.1.2. 电气原理图11.2. 技术数据12. 使用说明3 2.1. 注意事项3 2.1.1. 电气方面3 2.1.2. 使用方面5 2.1.3. 维护方面10 2.2. 安装指南10 2.2.1. 装箱单10 2.2.2. 安装注意事项10 2.2.3. 安装方法11 2.3. 控制面板14 2.3.1. 控制面板142.3.2. 功能介绍143. 售后服务16 3.1. 用户须知16 3.1.1. 用户须知16 3.2. 疑难解答16 3.2.1. 疑难解答16 3.3. 清洗保养17 3.3.1. 清洗保养17 3.4. 保修说明17 3.4.1. 保修说明17 3.5. 一键报修181. 产品介绍1.1. 产品部件1.1.1. 外观及部件介绍注：本示意图仅供参考！注：以上参数允许误差范围为±10%。

1.1.2. 电气原理图1.2. 技术数据型号a1（mm）b1（mm）c1（mm）d1（mm）ES50H-GD1(1)660390100410ES60H-GD1(1)760390100410ES80H-GD1(1)830422100442产品型号ES50H-GD1(1)ES60H-GD1(1)ES80H-GD1(1)容量（L）506080净重（kg）见包装箱贴见包装箱贴见包装箱贴额定功率（W）220022002200能效等级2级2级2级热水输出率80%80%70% 24小时固有能耗系数0.70.70.7额定电源220V~ 50Hz220V~ 50Hz220V~ 50Hz 额定压力（MPa）0.80.80.8额定温度（℃）757575防水等级IPX4IPX4IPX4注：以上参数(重量)允许误差范围为±10%该系列电热水器执行标准：GB 4706.12、GB 215192. 使用说明2.1. 注意事项2.1.1. 电气方面电源• 检查电表，电线直径是否符合热水器的额定电流，必要时请有资质的电工师傅检查一下。

海尔大型电力风热水杯上的产品说明书

IMPORTANT:To avoid damage to your cabinets, check with your builder 194°F (90°C).codes.q Product Dimensions Page 1 of 2A.Optional backguard may be installedB.27¾" (70.5 cm) depth with control panel, see NOTE*C.35¾" (90.2 cm) cooktop height when setting on the wheelsD.36" (91.4 cm) widthE.Model/serial rating plate locationA.Optional backguard may be installedB.27¾" (70.5 cm) depth with control panel, see NOTE*C.35¾" (90.2 cm) cooktop height when setting on the wheelsD.48" (121.9 cm) widthE.Model/serial rating plate locationA.18" (45.7 cm) upper cabinet to countertopB.30" (76.2 cm) model: 30" (76.2 cm) min. upper cabinet width 36" (91.4 cm) model: 36" (91.4 cm) min. upper cabinet width 48" (121.9 cm) model: 48" (121.9 cm) min. upper cabinet widthC.13" (33 cm) max. upper cabinet depthD.For minimum clearance to top of range, see NOTE**E.30¼" (76.8 cm) on 30" (76.2 cm) models 36¼" (92.1 cm) on 36" (91.4 cm) models 48¼" (122.6 cm) on 48" (121.9 cm) modelsF.6" (15.2 cm) min. clearance from both sides of range to side wall or other combustible materialG.15" (38.1 cm)H.22" (55.9 cm) on 30" (76.2 cm) models 28" (71.1 cm) on 36" (91.4 cm) models 40" (101.6 cm) on 48" (121.9 cm) models I.1½" (3.8 cm)J.3" (7.6 cm)K.5" (12.7 cm)L.6" (15.2 cm) on 30" (76.2 cm) models 14" (35.5 cm) on 36" (91.4 cm) models 24" (61.0 cm) on 48" (121.9 cm) models M.10½" (26.7 cm)N.6" (15.2 cm)O.6" (15.2 cm), see NOTE***48" (121.9 cm) modelsNOTE:The following illustration is for dimension planning purposes only,and the locations and appearances of the features shown may not match *NOTE:When installed in a 24" (61.0 cm) base cabinet with 25" (63.5 cm)countertop; front of oven door protrudes 1⁷⁄₈" (4.8 cm) beyond 24" (61.0 cm) base cabinet.Cabinet DimensionsCabinet opening dimensions shown are for 25" (64 cm) countertop depth,24" (61 cm) base cabinet depth and 36" (91.4 cm) countertop height.Dimensions must be met in order to ensure a flush fit to backwall.IMPORTANT:If installing a range hood above the range, follow the range hood installation instructions for dimensional clearances above the cooktop *NOTE:Receptacle must be rotated 90°for Canadian installation.**NOTE: Minimum Clearances30" (76.2 cm) models: 30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.36" (91.4 cm) models: 42" (106.7 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.48" (121.9 cm) models: 42" (106.7 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.***NOTE:If backwall is constructed of a combustible material and abackguard is not installed, a 6" (15.2 cm) minimum clearance is required for all models.Page 2 of 2。

海尔生活用电器产品说明书

31 SCHEMATICS 12/1/2005INDEXPAGE3.AC Panel4.230V AC Panel5.AC Panel Schematic6.230v AC Panel Schematic7.AC Wire Kit8.Stage Wire Kits-DVD Option Kit10.DC Panel11.DC Panel Schematic12.DC Panel Connectors14. Hull Harness15. Hull Harness Wire List16. Hull Harness Connectors17. Deck Harness18. Deck Harness Wire List19. Deck Harness Connectors20. Auto Fire System Schematic21. High Water Pump System Schematic22. Engine Panel Area SchematicPage 1REVISION DATE: 11/16/05 31 WIRE KITS WIRE SIZE COLOR LENGTH EYE EYE DESCRIPTION HOUSE BATTERY #11/ORED 10'3/8"3/8"BATT TO SW-HOUSE11/OYELLOW 9.5'5/16"3/8"BATT TO GND-HOUSE1YANMAR STARTER 2 GARED 8' 6"5/16"3/8"START TO STUD-YAN 2 GAYELLOW 8'3/8"3/8"ENGINE TO GND-YAN GNDS 6 GAGREEN/YELLOW 23'1/4"3/8"ARCH GND 6 GAGREEN/YELLOW 10' 6"1/4"5/8"CHAINPLATE PORT 6 GAGREEN/YELLOW 10' 6"1/4"5/8"CHAINPLATE STBD 10 GAGREEN/YELLOW 20'FUEL FILL GRD4 GA GREEN/YELLOW 30"1/4"3/8"MAST POST TO KEEL WIRE SIZE COLOR LENGTH EYE EYE DESCRIPTION SHORE POWER10-3ROMEX 15'SP1GNDS 6 GA GREEN/YELLOW 8'3/8"1/2"PEDESTAL GND WIRE SIZE COLOR LENGTH EYE EYE DESCRIPTION HOUSE BATTERY #21/ORED 11'3/8"3/8"BATT TO SW-HOUSE21/OYELLOW 2'3/8"3/8"BATT TO GND-HOUSE2BATT. CHAR. P/N 100284014-3ROMEX 7'BATT CHARGER INVERTER (120V)1/ORED 12"3/8"3/8"INV TO FUSE 1/ORED 18"3/8"3/8"FUSE TO SW 1/OYELLOW 18"5/16"3/8"INV TO GND 1/OGREEN/YELLOW 18"5/16"1/4"INV CASE TO GND 10-3ROMEX 7'INV IN 10-3ROMEX 7'INV OUT INVERTER (230V)1/ORED 1'3/8"3/8"FUSE TO SW 1/OGREEN/YELLOW 18"5/16"1/4"INV CASE TO GND 10-3ROMEX 7'INV IN 10-3ROMEX 7'INV OUT WINDLASS 2 GARED 24'1/4"5/16"BREAKER TO BOX-WL 2 GAYELLOW 24'3/8"5/16"GND TO BOX-WL 2 GARED 16"3/8"1/4"WINDLASS JUMPER BILGE KEEL 12 GABROWN 12' BILGE PUMP (+) 12 GAYELLOW 12' BILGE PUMP (-)AIR CONDITIONING 10-3ROMEX 18' AIR COND 14-3ROMEX 8'AC PUMP WIRE SIZE COLOR LENGTH EYE EYE DESCRIPTION WINDLASS2 GA RED 1' 6"5/16"5/16"BOX TO MOTOR-WL2 GA RED 1' 6"5/16"5/16"BOX TO MOTOR-WL 16 GA YELLOW 1' 6"5/16"F-spade CONTROL BOX NEG.ELECTRICAL STAGE 56STAGE 24A-MODULE P/NMODULE STAGE 24AOPTIONSSTAGE 34-DECK RIGGING P/N 1013359HUNTER 31 DC HULL HARNESS11/18/2005 WIRE#GAUGE COLOR LENGTH FUNCTION110RED/BLACK138"REFRIGERATION210YELLOW120"REFRIGERATION NEG.316ORANGE/RED134"LPG PANEL SW416YELLOW116"LPG INDICATOR NEG.3A16ORANGE/GREEN260"LPG SOLENOID (+)4A16YELLOW296"LPG SOLENOID (-)512BROWN/RED110"BILGE MANUAL SW612BROWN/ORANGE96"BILGE AUTO712YELLOW92"BILGE NEG.86YELLOW68"DC MDP NEG.96ORANGE/RED64"DC MDP POWER1012TAN46"BILGE POWER118ORANGE/GREEN34"BATTERY CHARGER128ORANGE/RED34"BATTERY CHARGER138YELLOW36"BATTERY CHARGER NEG1816PINK/BLACK206"WATER SENSOR (S)1916YELLOW202"WATER SENSOR (-)2212BROWN/BLUE310"BLOWER2312YELLOW292"BLOWER NEG.2412BROWN130"WATER PUMP2512YELLOW112"WATER PUMP NEG.2812BROWN/BLACK140"SUMP PUMP SW28A12BROWN/BLACK132"SUMP PUMP2912YELLOW62"SUMP PUMP NEG.3216RED/BLUE222"CO DETECTOR3316YELLOW204"CO DETECTOR NEG.32A16RED/BLUE388"CO DETECTOR33A16YELLOW354"CO DETECTOR NEG.3412RED174"12V OUTLET3512YELLOW156"12V OUTLET NEG.OUTLET3612RED 236"12V3712YELLOW202"12V OUTLET NEG.4116PINK184"FUEL SENSOR (S)4216YELLOW184"FUEL SENSOR (-)506YELLOW32"NEG BUS JUMPER6110WHITE/GREEN106"HW PUMP AUTO6210WHITE/RED100"HW PUMP MANUAL6310YELLOW88"HW PUMP NEG6416YELLOW/BROWN362"HW RELAY SW6516BROWN/RED362"HW ALARM IND6616YELLOW350"HW ALARM NEG6716BLACK/YELLOW222"FIRE EXT.67A16BLACK/YELLOW240"FIRE EXT. - SHUTDOWN6816BROWN/BLUE182"BLOWER RELAY6916YELLOW362"FIRE EXT. - SHUTDOWN BOX 7016RED72"IGNITION SWITCH7316WHITE/BROWN72"ENGINE STOP7416RED60"FUEL GAUGE POWER7516YELLOW48"FUEL GAUGE NEGATIVE7616RED6"FUEL GAUGE LIGHTHUNTER 31 DECK HARNESS REV.-B1/3/2005 WIRE#GAUGE COLOR LENGTH FUNCTION116BLUE312"CABIN LIGHTS216YELLOW306"CABIN LIGHTS NEG.316BLUE454"CABIN LIGHTS416YELLOW448"CABIN LIGHTS NEG.514GRAY/RED194"ANCHOR LIGHT614GRAY/GREEN194"STEAMING LIGHT716GRAY214"DECK LIGHT810YELLOW188"MAST LIGHTS NEG.916WHITE/ORANGE144"PORT MAIN SPEAKER1016WHITE/YELLOW144"PORT MAIN SPEAKER NEG.1116BLUE388"CABIN LIGHTS1216YELLOW382"CABIN LIGHTS NEG.1316BLUE292"CABIN LIGHTS1416YELLOW286"CABIN LIGHTS NEG.1516GRAY/YELLOW394"STERN LIGHT1616RED/BLACK324"GPS1816YELLOW388"STERN LIGHT NEG.1916BLUE/WHITE168"ARCH LIGHT2016YELLOW162"ARCH LIGHT NEG.2116WHITE/PINK162"PORT ARCH SPEAKER2216WHITE/YELLOW162"PORT ARCH SPEAKER NEG.2316WHITE/GRAY162"STBD ARCH SPEAKER2416WHITE/BLACK162"STBD ARCH SPEAKER NEG.2516GRAY/WHITE260"BOW LIGHT2616YELLOW254"BOW LIGHT NEG.2716TAN260"WINDLASS3016WHITE/BLUE346"STBD MAIN SPEAKER3116WHITE/BLACK346"STBD MAIN SPEAKER NEG.32RG-8X WHITE188"VHF COAX3910RED324"AUTO PILOT4010YELLOW318"AUTO PILOT NEG.4116YELLOW42"GPS NEG42WIND SP CABLE416"WIND SPEED436YELLOW24"NEG JUMPER。

海尔家用电热水器 FCD-HM40HⅠ(E) 说明书

6 规格·装箱单 1 安全警告（使用前请先阅读）外观及部件介绍装箱单检查电表，电线直径是否符合热水器的额定电流，必要时请有资质的电工师傅检查一下。

该热水器使用交流２２０Ｖ／５０Ｈｚ电源，使用独立插座（禁止使用多功能插座）并进行可靠接地，严禁在无可靠接地的情况下使用热水器。

请不要使用受损的电源线和电源插座及插头十分松弛的电器产品。

否则会引起触电、短路、火灾等事故。

应该确认电源插头能够与电源插座严密结合。

插座质量要符合国家标准，并且要及时擦拭电源插头上的金属片，防止金属片上沾有污渍而引起火灾等事故。

安装好后，首次使用必须先注满水后再接通电源。

若在容器水不满的情况下通电，加热管过热会造成故障。

寒冷地区冬季若长期不使用请掀动安全阀手柄，将水排空以防结冰损坏热水器（详见使用注意事项）。

热水器电源插座应安置在水喷淋不到的干燥处，请勿湿手插拔电源插头。

否则会出现触电、受伤等事故。

当电热水器被水严重浸湿后，再次使用前须经本公司认可的技术人员检验。

请您在开关水阀时，不要将喷头朝向人体，以免被一小股热水烫伤（５０℃以上的水可能导致烫伤）。

如果电热水器的电源线损坏，必须由售后人员用专用线缆进行更换（厂家提供）。

除专门技术维修人员外其他人不得拆卸、维修。

此不要放置在太冷能够结冰的环境中，如果结冰，容器和水管就会破裂，造成烫伤和漏水。

不要安装在室外。

不要落地安装。

应挂于坚实、牢固的墙壁上。

不要安装在无法排水的地方。

若连接排水管，应将排水管接于下水道口处，以免将室内溅污。

电源线及插座要求机器使用前长期不使用热水器时采用２２０Ｖ／５０Ｈｚ交流电源当电源线损坏时儿童淋浴时必须在大人的操作指导下进行！小心烫伤外不要将汽油等易燃物品放置在热水器附近，否则可能会引起火灾。

关于安全阀的使用关于机配管路的使用本电热水器配有安全阀，为了使用安全，不可私自改动其安装位置，严禁堵塞其出口。

安全预警专家注意防水本产品的机配管路是“防电墙”产品的有机组成部分，切勿随意拆除，否则由此带来的安全隐患所造成的伤害，本公司不予承担。

海尔 JSQ30-16GX11(12T)U1 16升双增压零冷水燃气热水器使用说明书

型号：)·使用前请仔细阅读本说明书·本公司保留说明书解释权·产品外观请以实物为准·阅后请与发票一并妥善保存·如遇产品技术或软件升级，恕不另行通知·本产品只适合在中国大陆销售和使用该系列家用燃气热水器执行国家标准： GB 6932-2015“1+5”成套服务尊敬的用户：感谢您选择和使用我们的产品。

我们承诺：您的产品需要安装或维修等服务时，我们将为您提供：“1+5″的成套服务： 1：一次就好服务。

5：五项增值服务：（1）安全测电服务：为您提供安全测电并提醒讲解到位服务；（2）讲解指导服务：向您讲解产品使用、保养常识，指导用户正确使用服务；（3）一站通检服务：服务好本产品，对家中其他本企业产品进行通检服务；（4）全程无忧服务：为您提供设计、送货、安装、清洗、延保、以旧换新等服务；（5）现场清理服务：服务完成后将服务现场清理干净。

为体现真诚、贴心，我们友情提醒：产品的安装服务，因用户的安装环境、个性需求不同，安装过程中如需辅加材料或有特殊服务项目需要支付材料等费用，您可以通过“海尔智家”APP-“智家服务”-“收费标准”进行查看，并给予监督。

如未按标准收费或服务规范执行不到位，可拨打服务监督电话400 699 9999，或通过“海尔智家”APP-“智家服务”-“在线客服”进行监督、评价。

如果您的产品有服务需求,欢迎体验海尔智家自助服务专区(预约服务、一键安装、一键维修)：手机搜索安装“海尔智家”APP，您可通过“智家服务”版块选择安装、维修等服务。

如您需要选购更多产品,可在“海尔智家”APP-“商城”进行选购。

（更便捷、更快速、更省钱）期待您的参与！智能家电操控智慧场景定制智家商城购物家电报装报修使用说明书家用燃气快速热水器地址：山东省青岛市黄岛区海尔工业园青岛经济技术开发区海尔热水器有限公司版次：2022年第1版专用号：0040511293检验印章：产品合格证产品名称：见铭牌/条码产品型号：见铭牌/条码出厂编号：见铭牌/条码检验日期：见铭牌/条码检验结论：经检验合格准予出厂操作按键及状态显示面板将电源插头正确插入２２０Ｖ／５０Ｈｚ的独立电源插座。

海尔电子科技有限公司电子水洗机用户指南说明书

of the impeller.
7. Insert the pump cover and press
down ⁠.
2
a The pump cover clicks into position.
1
8. Install the filter system.
Troubleshooting
Fault
E:32-00 will light up alternately or indicator for water supply lights up.
bile device and follow the instructions.
2. Scan the QR code with the Home Connect app.
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.
Hardness mmol/l range
Setting value
Medium Medium Medium Hard Hard Hard
Soft
0 - 1.1
H00
Soft
1.2 - 1.4 H01
1.5 - 1.8 1.9 - 2.1 2.2 - 2.9 3.0 - 3.7 3.8 - 5.4 5.5 - 8.9
residue.
2. Turn the coarse filter anticlock-

海尔电器商品说明书

To see Parts & Accessories available for your motorcycle and complete product description, fitment and warranty terms and conditions for all products listed, refer to the 2020 Harley-Davidson® Genuine Motor Parts & Accessories Catalog or the 2020.
52000248
49000114A
56000135 56100157
41300116
25700520 25700521 25700467 25700491
50500640 50600185 33600111 41600208 34023-08 33600259
41000008C 41000445 29400397 61300994 92500060 64800062 65100161 25566-06 25928-06
Front Brake Caliper Kit
DefianceTM Collection Rider Footboard Kit
Screamin’ Eagle® Milwaukee-Eight® Engine Stage IV Kit
Low-Profile Solo Touring Seat
DESCRIPTION ACCESSORIES FOR FIT Low-Profile Solo Touring Seat ACCESSORIES FOR FUNCTION Chopped Engine Guard HAND CONTROLS & GAUGES Profile Custom Mirrors - Satin Black Defiance™ Collection Hand Grips - Black Anodized WHEELS & ROTORS Front Brake Caliper Kit - Dual Disc - Red ENGINE & CHASSIS TRIM Upper Rocker Box Cover - Gloss Black Milwaukee-Eight® Gloss Black Lower Rocker Box Cover (2) Milwaukee-Eight Gloss Black Cam Cover Milwaukee-Eight Gloss Black Primary Cover FOOT CONTROLS Defiance Collection Rider Footboard Kit - Black Anodized Defiance Collection Brake Pedal Pad - Large, Black Anodized Defiance Shifter Peg - Black (2) Billet Style Rear Brake Lever - Satin Black Billet Style Heel/Toe Shift Lever - Satin Black Custom Gear Shift Linkage - Gloss Black SCREAMIN’ EAGLE® PERFORMANCE Screamin' Eagle® Pro Street Tuner Screamin' Eagle Smart Tune PRO Automatic Tuning Module Screamin' Eagle Extreme Ventilator Extreme Air Cleaner Screamin' Eagle Ventilator Extreme Air Cleaner Cover Screamin' Eagle Milwaukee-Eight Engine Stage IV Kit - 107 to 114CI Screamin' Eagle High-Flow Exhaust System with Street Cannon Mufflers - Satin Black Two-Piece 4.5 in. End Caps Cam Drive Retention Kit Cam Spacer Kit

海尔电热器操作指南说明书

Unpacking1. Unpack all materials used to protect the heater inside of carton. Retain plastic caps attached to exposed fittings for use during storage.2. Remove heater, accessories and all hardware from carton.3. Inspect all items for damage that may have occurred during shipment.General Safety InformationMake sure you read and thoroughly understand these safety and operating instructions. Keep these instructions for future reference. They are your guides to safe and proper operation of this heater.Safety information appears throughout this manual. Pay close attention to them. Below are definitions for the safety information listed throughout this manual.Indicates an im m inen t lyhazardous situation which, if notavoided, WILL result in death or serious injury.Indicates a potentially hazardoussituation which, if not avoided, COULD result in death or serious injury.Indicates a potentially hazardoussitua t ion which, if not avoided, MAY result in minor or moderate injury.Consumer: Retain this manual for future reference.Dyna-Glo ®Delux Natural Gas Radiant HeatersPlease read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.DescriptionDyna-Glo Delux Models RA100NGDGD and RA250NGDGD heaters are 50,000 to 100,000 and 250,000 BTU/Hr construction heaters. These heaters use natural gas for combustion. They are primarily intended for temporary heating of well-ventilated buildings under construction, alteration or repair. These heaters should be utilized in sheltered, well-ventilated areas, but never in occupied dwellings.Ignitor SizeGapL x W x H (in.)RA100NGDGD 50,000 to 104 ft 3/hr (2.95 m 3/h) 8” W.C. 14” W.C.7.5” W.C. 0.19“ (4.8mm) 16.3 x 16.3 x 29.8 100,000(41.4 x 41.4 x 75.7 cm)RA250NGDGD 250,000 260 ft 3/h (7.36 m 3/h) 10 PSI 250 PSI6 PSI 0.19” (4.8 mm) 14.7 x 14.7 x 44.3 (37.3 x 37.3 x 112.5 cm)Fuel Type – Natural Gas Only Ignition Type – P iezo (RA100NGDGD)Minimum Operating Temp. – -20°F (-29°C)Pilot (RA250NGDGD)SpecificationsGHP Group, Inc.6440 W Howard St Niles, IL 60714ANS Z83.7-2011 CSA 2.14-2011 Construction HeaterC USC USFigure 1 – Models RA100NGDGD / RA250NGDGDGeneral Safety Informationconstruction heater in accordance with ANS Z83.7 CSA 2.14. Other standards govern the use of fuel gases and heating products for specific uses. Your local authority can inform you of these. The primary purpose of these construction heaters are to provide temporaryheating of building under construction, alteration, or repair. When properlyused, the heater provides safe economical heating. Products of combustion are vented into the heated area.- For either indoor or outdoor use. Adequate ventilation must be provided.IMPORTANT: Every possible circum-stance that might involve a hazard can-not be anticipated. The warnings in this manual on tags or decals affixed to the unit are not all inclusive. If a procedure,work method, or operating technique not specifically recommended by Day-ton is used, you must make sure it is safe for you and others. You should also ensure that equipment will not be dam-aged or be made unsafe by the operat-ing or maintenance method you use.death! Some people are more affected by Carbon Monoxide than others. Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, and/or nausea. If you have these signs, theheater may not be operating properly or the area may not be sufficientlyventilated. Get fresh air at once! Have heater serviced.Carefully install and always use great carewhen operating this heater. Be sure to research and follow all local ordinances and codes. In the absence of local codes, with the Standard for the Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 and the Natural Gas and Propane Installation Code CSA B149.1.Natural Gas: Natural gas has a very distinctive odor that will help you detect a leak. However, this odor may fade in time. Natural gas may be present in the area even though no odor is detected.– U se only natural gas. Do not attempt to use propane gas. Use only factory preset regulator provided on heater.– P rovide adequate ventilation. Before using heater, provide at least a 3square foot (.28 m 2) opening of fresh, outside air for every 100,000 BTU/Hr rating.CaliforniaProposition 65Warning: Fuels used in gas or oil fired appliances and the products of combustion of such fuels, contain chemicals known to the State ofCalifornia to cause cancer, birth defects or other reproductive harm. This product contains chemicals, including lead and lead compounds, known to the state ofCalifornia to cause cancer, birth defects or other reproductive harm. Wash hands after handling.– T his heater should be utilized in sheltered, well-ventilated areas, but never in occupied dwellings.– D o not use heater in occupieddwellings, in living or sleeping areas.– K eep appliance clear and free from combustible materials, gasoline, paint thinner, and other flammable vapors and liquids. Dust is combustible. Do not use heaters in areas with high dust content.– C heck heater for damage before each use. Do not use damaged heater.®Radiant HeatersGeneral Safety Information (Continued)Minimum heater clearance from combustibles:Sides: 6 feet (1.8 m) Top: 5 feet (1.5 m)Floor: Combustible - Not for use on finished floors– T he heater, other than a heater with integral propane gas container, must be located at least 6 feet (1.8 m) (in Canada, distance must be 10 feet [3 m]) from any propane gas container.– B lower or radiant type heaters shall not be directed toward any propane gas container within 20 feet (6 m).– C heck hose before each use of heater. Do not use if hose is cut or damaged. Replace with hose specified by manufacturer.– A lways be sure to place the heater onheater is in operation.– T damage may occur.– P water or rain.– K from the heater.– N – A lways wear gloves when handling the heater to prevent injury.– N ever attach ductwork to heater.– D o not alter heater. Keep heater in its original state.– D o not use heater if altered.– T urn off gas supply to heater whennot in use.– U se only original replacement parts.This heater must use design specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injury.AssemblyMODEL RA100NGDGD1. Provide natural gas supply system.2. Install plumbing to a low pressure natural gas source to heater. The source must be regulated to 1/2 PSI, maximum 3/4’’ (19 mm) I.D. pipe or flexible connector, not longer than 10 feet (3 m).3. Be sure to use thread sealingcompound when connecting the hose to the heater at the 1/2’’ (13 mm) NPT fitting at the regulator inlet. Tighten all fittings with a wrench.4. Open natural gas supply valve Never use an open flame to check for aleak. Apply 50/50 mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.6. Close natural gas supply valve.MODEL RA250NGDGD1. Insert AA battery (included) into ignition by turning COUNTERCLOCKWISE and unscrewing ignition cap.2. Provide natural gas supply system.3. Install plumbing to a natural gas source to heater.4. Connect gas supply to heater using minimum 3/8” (10 mm) ID pipe.Maximum pipe length is 10 feet (3 m).5. Connect hose or plumbing to 1/2” (13 mm) NPT flare fitting at thevalve inlet. Tighten all fittings with a wrench.6. Open natural gas supply valveSLOWLY. Check all connections for leaks. Never use an open flame to check for leaks.7. Close natural gas supply valve. NOTE: Keep hands and face away from outlet (around top of shelf) of heater while attempting to start heater.Models RA100NGDGD and RA250NGDGDDyna-Glo Delux Operating Instructions and Parts ManualFigure 3 – Heater Control Knob –RA100NGDGDHot while inoperation. Do nottouch. Keep children, clothing, furniture,gasoline, and other liquids havingflammable vapors away.The gas supply attaches to the heaterby a minimum 3/8’’ (10 mm) I.D. pipeor flexible connector. User must supplypipe or flexible connector. The lengthshould be no more than 10 feet (3 m).The natural gas moves through the2. Always be sure to place the heater ona stable and level surface while theheater is in operation. Be sure that nostrong winds blow into the ends ofthe heater.to OFF position.4. Turn natural gas supply valve on.5. Depress heater control knob andturn counterclockwise to (IGN) LOWTO SHUT DOWN HEATER1. Shut off the main burner valve, beingsure to wear a glove for protection.Turn the control knob to the OFFposition.2. Firmly close the natural gas supplyvalve.TO RESTART HEATER1. Wait five minutes for heater to cool.2. Follow steps in TO START HEATERsection.TO START HEATER (RA250NGDGD)1. Follow all of the safety, ventilationand installation instructionspreviously noted in this manual.2. Always be sure to place the heater ona stable and level surface while theheater is in operation. Be sure that nostrong winds blow into the ends ofthe heater.3. SLOWLY open the gas valve.4. Push in and hold safety valve buttonwhile pushing ignitor button untilpilot lights (see Figure 4).NOTE: Hose may be filled with air, ifso, allow around 15 seconds for gas toreach pilot.5. If pilot does not light, repeat Step 4.6. When pilot stays lit, fully open themain burner valve by turning thehandle of the burner valve counter-clockwise until it stops all the way tothe ON position.®Radiant HeatersFigure 4 – RA250NGDGD Part IdentificationOperation (Continued) NOTE: Arrows on main burner valve handle show directions for ON and OFF.TO SHUT DOWN HEATER1. Firmly close the natural gas supply valve.2. Shut off the main burner valve, being sure to wear a glove for protection.the way to the OFF position.TO RESTART HEATER1. Wait five minutes for heater to cool.2. Follow steps in TO START HEATERsection.Running heaterbelow specified gaspressure may cause flashback. Duringflashback, the burner flame is mostlyyellow. The flame will burn inside theburner tube causing a roaring noise. Ifflashback occurs, turn heater off. Afterburner tube cools off, restart heater.NATURAL GAS SUPPLYYou must provide the natural gas supplyalong with all pipe and fittings.Check with your local gas supplier toproperly size all of your supply lines. Besure to follow all local codes, or refer tothe Natural Fuel Gas Code Handbook –NFPA54/ANSI Z223.1, or the Natural GasInstallation Code – CAN/CSA B149.1.VENTILATIONA three square footopening of freshoutside air for each 100,000 BTU/Hr ofheater output must be provided tooperate each heater safely. If the properventilation air is not provided, carbonmonoxide poisoning can occur.Always be sure that the properventilation is being provided beforestarting this heater.FRESH OUTSIDE AIR OPENINGREQUIREMENTSHeater size Opening100,000 BTU 3.0 ft2 (.28 m2)250,000 BTU 7.5 ft2 (.70 m2)Read and understandall of the warnings inthe General Safety Information pages of thismanual. They are essential to the safeoperation of this heater. Be sure to followall local codes when operating this heater.Be sure to leak test allfittings and pipeconnections after installation or repairs. Usea 50/50 mixture of liquid dish soap andwater. Bubbles forming reveal a leak. Youmust repair all leaks at once!Models RA100NGDGD and RA250NGDGD Dyna-Glo Delux Operating Instructions and Parts ManualFigure 5 – RA100NGDGD Part IdentificationKnobNever attempt toservice heater whileit is connected to natural gas supply,operating, or hot. Severe burns can occur.1. Always keep heater clean.2. Inspect heater before each use.Check connections for leaks. Applya 50/50 solution of dish soap andwater. Bubbles forming show a leakthat must be corrected. Correct leaksat once.3. Inspect regulator hose assemblybefore each use. If hose is highlyworn or cut, replace with hosespecified by manufacturer.4. Keep appliance area clear and freefrom combustible materials, gasoline,and other flammable vapors andliquids.5. Have heater inspected yearly by aqualified service person.6. The flow of combustion andventilation air cannot be obstructed.STORAGEDisconnect heaterfrom natural gassupply.1. Place plastic cover over brass fittingon inlet connector.2. Store in a dry, clean, safe place.3. When taking the heater out ofstorage, always check inside theheater. Small animals or insects mayplace foreign objects in the heater.Keep heater free from foreign objectsand combustible materials.®Radiant HeatersSymptom Possible Cause(s) Corrective ActionBurner fails to lightBurner lights but goes outwhen automatic controlvalve button is releasedBurn rate is low, emitterdoes not glowFlames are extremely highand coming from emitter1. More warm-up time needed2. Gas pressure is low3. Thermocouple loose or in need ofreplacement4. Automatic control valve in need ofreplacement1. Main burner valve not completely open2. Clogged gas orifice3. Low gas pressure4. Low gas supply1. Main burner valve not fully open2. Plugged gas orifices3. Low gas pressure4. Low fuel supplyUnit has been connected to a propane gassupply instead of natural gas1. Relight, holding control valve button in for45 seconds2. Inspect natural gas supply3. Tighten, reconnect or replacethermocouple4. Replace automatic control valve1. Completely open main burner valve byturning control knob to HIGH position2. Replace gas orifice3. Check gas supply, regulator function4. Contact gas supplier1. Fully open main burner valve by turningcontrol knob towards HIGH position until itstops2. Replace gas orifice3. Check gas supply, regulator output4. Consult gas supplierCheck gas source and replace with natural gassupplyTroubleshooting ChartFor Repair Parts, call 1-877-447-4768 Please provide following information:-Model number-Serial number (if any)-Part description and number as shown in parts list ArrayFigure 6 – Repair Parts Illustration for Natural Gas Radiant Heater RA100NGDGDModel RA100NGDGDDyna-Glo Delux Operating Instructions and Parts ManualRepair Parts List for Natural Gas Radiant Heater RA100NGDGD1 Top Cover 5002854 12 Guard 2315528 13 Emitter 2315519 14 N ozzle2315521 1 5 Nozzle Connector 2315545 1 6 Nozzle Nut2315546 1 7 Main Gas Tubing Assy (NG) 2315523 1 8 Nozzle Bracket 2315517 1 9 Flame Shield 2315516 2 10 Thermocouple 2201584 1 11 Spark Plug2201583 1 12 Thermocouple Holder 2315520 1 13 Base5002851 1 14 Control Knob 2101451 1 15 Control Valve GS22 (8B) 1 16 Fitting2304948 2 17 Tubing Inlet Assy2315524 1 18 Fitting-Regulator to Tubing Inlet 2315547 1 19 Regulator2315555 1 20 Regulator Bracket 2315518 1ReferenceNumber DescriptionRA100NGDGDQuantityHeater must use designspecific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries.Figure 7 – Repair Parts Illustration for Natural Gas Radiant Heater RA250NGDGDFor Repair Parts, call 1-877-447-4768Please provide following information:-Model numberModel RA250NGDGDDyna-Glo Delux Operating Instructions and Parts ManualRepair Parts List for Natural Gas Radiant Heater RA250NGDGD1 Top Cover 5002854 12 Guard 2315554 13 Emitter 2315537 14 Upper Base 5002853 15 Base Cover 2315532 16 Lead Wire 2315643 17 Tilt Switch 2300186 18 Lower Base 5002852 19 Blanket 2315539 1 10 Insulation 2315544 1 11 Flame Shield 2315540 1 12 Thermocouple 2201591 1 13 Spark Plug2201583 1 14 Spark Plug Bracket 2315609 1 15 Bracket2315520 1 16 Box for Lead Wire 2315535 1 17 Pilot Assy GL250.39 1 18 Pilot Bracket 2315608 1 19 Wind Box 2315610 1 20 Ignition Wire 2201585 1 21 Battery 2300481 1 22 Ignition 2201220 1 23 Regulator2315513 1 24 Regulator Holder 2315536 1 25 Regulator Connector 2315547 1 26 Inlet Tubing Assy 2315542 1 27 Connector 2315549 1 28 Control ValveGS16 1 29 Contol Valve Fixing Nut 2305687 1 30 Contol Valve Bracket 2315538 1 31 Ball ValveGQ01 1 32 Ball Valve Connector 2305391 1 33 Pilot Connector 2315548 1 34 Main Tubing Assy 2315550 1 35 Pilot Tubing 2001402 1 36 Base Shield2315541 1 37 Rubber Ring for Wire 2315543 1 38 Nozzle Bracket 2315533 1 39 Nut2101008 1 40 Nozzle Connector 2315534 1 41 Nozzle 2315546 1Reference Number DescriptionRA250NGDGDQuantityHeater must use designspecific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries.WarrantyRA100NGDGD and RA250NGDGD Dyna-Glo Delux Operating Instructions and Parts ManualLIMITED WARRANTY:This limited warranty is extended to the original retail purchaser of this Forced Air/Convection/Radiant Heater and warrants against anydefect in materials and workmanship for a period of one (1) year from the date of retail sale. GHP Group, Inc., at it’s option, will eitherprovide replacement parts or replace or repair the unit, when properly returned to the retailer where purchased or one of our service centersas directed by GHP Group, Inc., within one (1) year of retail purchase. (Shipping costs, labour costs, etc. are the responsibility of the purchaser.)DUTIES OF THE OWNER:This heating appliance must be operated in accordance with the written instructions furnished with this heater.This warranty shall not excusethe owner from properly maintaining this heater in accordance with the written instructions furnished with this heater.A bill of sale,canceledcheck or payment record must be kept to verify purchase date and establish warranty period.Original carton should be kept in case of warrantyreturn of unit.WHAT IS NOT COVERED:1.Damage resulting from use of improper fuel.2.Damage caused by misuse or use contrary to the owners manual and safety guidelines.3.Damage caused by a lack of normal maintenance.4.Fusese of non-standard parts or accessories.6.Damage caused in transit.Freight charges on warranty parts or heaters to and from the factory shall be the responsibility of the owner.This warranty does not imply or assume any responsibility for consequential damages that may result from the use,misuse,or the lack ofroutine maintenance of this heating appliance.A cleaning fee and the cost of parts may be charged for appliance failures resulting from lack ofmaintenance.This warranty does not cover claims which do not involve defective workmanship or materials.FAILURE TO PERFORMGENERAL MAINTENANCE(INCLUDING CLEANING)WILL VOID THIS WARRANTY.THIS LIMITED WARRANTY IS GIVEN TO THE PURCHASER IN LIEU OF ALL OTHER WARRANTIES,EXPRESSED OR IMPLIED,INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE.THEREMEDY PROVIDED IN THIS WARRANTY IS EXCLUSIVE AND IS GRANTED IN LIEU OF ALL OTHER REMEDIES.IN NO EVENT WILLGHP GROUP, INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.Some states do not allow limitations on how long an implied warranty lasts,so the above limitation may not apply to you.Some states do notallow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.CLAIMS HANDLED AS FOLLOWS:1.Contact your retailer and explain the problem.2.If the retailer is unable to resolve the problem,contact ourCustomer Service Dept.detailing the heater model,the problem,and proofof date of purchase.3.A representative will contact you.DO NOT RETURN THE HEATER TO GHP GROUP,INC.unless instructed by our Representative.This warranty gives you specific legal rights and you may also have other rights which vary from state to state.TO REGISTER THE WARRANTY ON YOUR HEATER,PLEASE FILL OUT THIS CARD COMPLETELYAND MAIL WITHIN14DAYS FROM DATE OF PURCHASE OR REGISTER ON-LINE AT NAME:______________________________________PHONE:()__________________EMAIL:____________________________ADDRESS:_________________________________CITY:______________________________STATE:__________ZIP:____________MODEL:____________________SERIAL#:_______________________________________DATE PURCHASED:__________________DEALER PURCHASED FROM:____________________________________________TYPE OF STORE:__________________________CITY&STATE WHERE PURCHASED:______________________________________________PRICE PAID:_______________________Please Take a Minute To Give Us Your Answers To The Following Questions.All Responses Are Used Solely For Market Research And Are Held In Strict Confidence.Who primarily decided this purchase?Male Female18-2425-3940-5960and overPurpose of Purchase?_______________________________________________________________________________________________Do you own any other portable heaters?Yes No If yes,type____________________________brand_____________________How do you intend to use your new heater?Construction Site Farm Warehouse/Commercial Garage/Outbuilding OtherHow did you become aware of this heater?In-Store Display Newspaper Ad Magazine Ad Friend/RelativeTV Commercial Store Salesperson Other___________________________What made you select this heater?Style Size/Portability Price Package Brand Other___________________Do you:own rent Would you recommend this heater to a friend?Yes NoPlease give us your comments:________________________________________________________________________________________THANK YOU FOR COMPLETING THIS FORM!Information will be held confidential.WARRANTY REGISTRATIONIMPORTANT:We urge you to fill out your warranty registration card within fourteen (14)days of date of purchase.You can also register your warranty on the internet atplete the entire serial number.Retain this portion of the card for your records.SAVE THIS CARD!Place Postage Stamp Here Tel: (877) GHP Group, Inc.6440 W Howard St Niles, IL 60714-3302GHP Group, Inc.6440 W Howard StNiles, IL 60714-3302。

带WIFI款电热水器功能说明书资料

WIFI款电热水器功能说明书编写：＿＿＿＿＿审核：＿＿＿＿＿会签：＿＿＿＿＿批准：＿＿＿＿＿一、适用对象：适用于速热、储水式电热水器的电控部分。

二、电控性能指标：1.工作电压范围：50/60Hz，175～260VAC（±5VAC）2.工作环境温度范围：-10~90℃。

3.待机消耗功率：220V条件下，3W以下。

4.功率调节范围：5000W以下。

（220V）三、显示控制：显示板上有一个数码显示屏，4个触摸式按键，1个WIFI模块，1个温度传感器等组成。

按位置1-5标号进行说明：1：标号1是开关机键，可以进行开关机器的设置。

短按一次，蜂鸣器响一声并伴随着开机动作，再按一次短按操作是关机动作。

此键还是复用键，有WIFI重置功能和清除用户黑白名单功能，操作方式如下：长按开关机键5秒不放，可以听到蜂鸣器响一声，即是进行WIFI重置和清除用户黑白名单的动作。

2：标号2是功能加键，可以进行温度加的设置、开机定时加的设置、关机定时加的设置，功率档位加的设置等。

3：标号3是功能减键，可以进行温度减的设置、开机定时减的设置、关机定时减的设置，功率档位减的设置等。

4：标号4是设置功能键，可以进行温度、开机、关机，功率档位的模式切换设置。

此键还是复用键，有WIFI手动配置和智能配置的切换的功能，操作方式如下：长按设置功能键3秒不放，可以听到蜂鸣器响一声，即是进行WIFI手动配置和智能配置的切换操作。

5：标号5是WIFI模块。

显示板上的功能模式的设置范围如下有：A：设置温度：在开机的状态下操作控制加键或者减键可以进行温度的设置，温度设置范围在30-75度之间，如果在加热状态的话加热图标显示，在保温的状态下保温图标显示。

B：定时开机：在关机的状态下按设置功能键，可以切换到开机预约定时的设置，然后再按加键或者减键设置开机定时时间，设置范围在０-２４小时之间。

C：定时关机：在开机的状态下按设置功能键，可以切换到关机预约定时的设置，然后再按加键或者减键设置关机定时时间，设置范围在０-２４小时之间。

海尔快热式电热水器（即热式水龙头）使用说明书

说明书菲林制作单图号型号名称印刷颜色尺寸设计/日期DSK30HP3-X-10DSK30HP3-X中文说明书双色印刷145x210mm±3刘嘉敏2020.07.2780g双胶纸材料成型方式装订使用说明书华凌快热式电热水器（即热式水龙头）使用前请仔细阅读本说明书，并妥善保管安全警示禁止、强制、注意01服务指南1313产品参数故障自检15环保清单包修须知保修卡产品满意程度部件名称产品简介03操作指引使用说明04保养维护清洁保养05安装说明电源线安装安装说明0808电器原理图10机器安装1201安全警示表示【禁止】的内容禁止阳光照射禁止易燃物品禁止潮湿区域禁止湿手触摸为保证使用安全，避免对您和他人造成伤害和财产损失，请您务必遵守以下安全注意事项，不遵守安全警告而错误使用可能导致事故发生。

电源线应牢固固定在固定电源上；禁止私自改造电源线。

严禁将即热水龙头安装在可能结冰区域，若机器中的水有可能结冰，则禁止给即热水龙头加热，并断开电源请勿让幼童操作、接触、靠近或攀爬即热水龙头，儿童、智力障碍及感官能力弱者应在监护者协同下使用。

禁止在即热水龙头附近放置易燃易爆物品。

严禁将即热水龙头安装在室外；禁止将即热水龙头安装在高温物体和阳光直射附近。

严禁将即热水龙头与太阳能热水器连接使用。

严禁私自改造即热水龙头，禁止将机器用于淋浴；水龙头出水嘴不允许加装过滤嘴、净化器等阻流装置严禁将产品倒置、倾斜安装，请按照进水标识方向安装本产品家庭停水、管路维修或长时间不使用时，务必要先通水，待管路中的气体、脏污水排出后方可接通电源请勿将即热水龙头中的水直接作为饮用水或类似用途；请勿在即热龙头上披挂、晾晒毛巾等物品。

禁止用移动插座、规格不足的插座、破损的电源线；禁止湿手碰触插头，以防触电；禁止带电安装或维修。

切断电源时，请勿直接拉拔电源线，以防拉断，如果电源线软线破损，为避免危险，必须由我司专职人员更换。

产品在使用过程中有若有异响、异味、高温、变形等异常时，请立即切断电源、水源，并停止使用。

海尔电子蒸汽水Home Connect指南说明书

3. Press
repeatedly until the right
water hardness has been set.
4. To save the settings, press
for 3 seconds.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
The flow rate must be at least 10 l/min when the water supply is open.
The filters in the water connection of the supply or AquaStop hose are blocked. 1. Switch off the appliance. 2. Pull out the mains plug. 3. Turn off the water tap. 4. Unscrew the water connection. 5. Remove the filter from the sup-
4. Insert the lower spray arm. a The spray arm clicks into position. 5. Insert the upper spray arm and screw it firmly in place.
Clean wastewater pump
1. Disconnect the appliance from the power supply. 2. Remove the filter system. 3. Scoop out any water. 4. Prise off the pump cover using a

海尔 ES60H-GRR 60升健康抑菌横式电热水器使用说明书

储水式电热水器使用说明书·使用前请仔细阅读本说明书·本公司保留说明书解释权·产品外观请以实物为准本标识点亮，则表示您家即刻停止使用并拔掉电源插头，同时切记不要触及家中任何电器的外壳，并马上联系售后部门(售后服务电话:4006 999 999)或物业公司，由专业电工进行系统检测直至本标识熄灭。

该系列电热水器执行标准：GB 4706.12、GB 21519务必使用220V/50Hz的独立电源。

为了确保安全，热水器应使用独立插座(禁止使用多功能插座)，并进行可靠接地，且插座质量应符合国家标准，严禁在无可靠接地的情况下使用热水器。

用测电笔测量火线、零线是否接反。

为保证机器的正常工作及家庭的用电安全，在安装时必须采用与所购机器插头相匹配的电源插座。

装箱单清洗与保养注：以上参数(尺寸、重量)允许误差范围为±10%。

安装好后，首次使用因内胆无水，必须先开启自来水进水阀门和混合阀，将混合阀调到最大出热水档处，待喷头或其它出水口连续出水后(则表示此时容器内水已满)，关闭混合阀。

检查各接口处无漏水后接通电源。

A 进冷水口B 出热水口C 加热管D 进水绝缘管E 出水绝缘管F 镁棒G 搪瓷内胆正视图侧视图剖视图1.如您家有时停水，请在停水时断电。

在通电之前请将出水阀门打到最大出热水档处，待出热水阀门连续出热水后，关闭阀门，表明内胆注满水，然后通电，这样可延长加热管使用寿命。

2.如果您的住所是高层建筑，自来水压力超过产品额定压力范围(如：大于0.8MPa)，建议您联系我们售后购置减压阀，这样可以保证热水器可靠使用，保证热水器使用寿命。

3.为保证热水器使用寿命，特对产品采用镁棒防腐，镁棒像电池一样也会消耗能量，这时就需更新。

建议您从使用热水器开始，每两年联系我们的售后一次，更换新的镁棒(整机包修期内免材料费，仅收服务费)这样可以保证且大大延长热水器的寿命 (正常使用条件下，具有免更换镁棒技术的电热水器无需更换镁棒)。

es40h-s1说明书

ES40H-J1(E) ES50H-J1(E) ES60H-J1(E)ES40H-GZ1(1)ES50H-GZ1(1)ES60H-GZ1(1)
本标识是海尔热水器公司“安全预警”专用标识，内部使用了本公司的专利技术(ZL01135300.7)，在确保您安全洗浴的同时，时刻监测您家庭的地线是否带电。

如本标识点亮，则表示您家的地线已经带电，应即刻停止使用并
拔掉电源插头，同时切记不要触及家中任何电器的外壳，并马上联系售后部门(售后服务电话:4006 999 999)或物业公司，由专业电工进行系统检测直至本标识熄灭。

务必使用220V/50Hz的独立电源。

为了确保安全，热水器应使用独立插座(禁止使用多功能插座)，并进行可靠接地，且插座质量应符合国家标准，严禁在无可靠接地的情况下使用热水器。

用测电笔测量火线、零线是否接反。

由于此款电热水器功率较大，为保证本机的正常工作及家庭的用电安全，建议您在安装时采用与本机插头(16A)相匹配的电源插座。

型号：
扫描二维码智享科技魅力
使用前请仔细阅读本说明书本公司保留说明书解释权产品外观请以实物为准阅后请与发票一并妥善保存
如遇产品技术或软件升级，恕不另行通知本产品只适合在中国大陆销售和使用该系列电热水器执行国家标准：
GB4706.12-2006《家用和类似用途电器的安全储水式热水器的特殊要求》
版次：2018年第2版专用号：0040506632 厂家代码：V 98497
地址：青岛经济技术开发区海尔工业园在线报修地址：售后服务热线：4006 999 999 网址：
青岛经济技术开发区热水器有限公司。

【2018-2019】海尔电热水器怎么样word版本 (5页)

本文部分内容来自网络整理，本司不为其真实性负责，如有异议或侵权请及时联系，本司将立即删除！== 本文为word格式，下载后可方便编辑和修改！ ==海尔电热水器怎么样导语：海尔，一个中国再熟悉不过的品牌了。

不管是童年记忆的海尔兄弟，还是生活中使用的冰箱空调洗衣机，海尔跟人们的生活已经密不可分了。

海尔热水器凭借良好的质量和服务，开始“占领”千家万户。

那么，你知道海尔热水器怎么用最省电吗?海尔电热水器使用方法是怎样的呢?今天我来为大家详细解说海尔电热水器使用说明书，帮助大家进一步的了解海尔热水器怎么用最省电。

一、海尔电热水器使用说明书之产品部分海尔集团是全球领先的整套家电解决方案提供虚实融合通路商。

经过29年创业创新，发展成为全球白电第一品牌。

201X年7月，在《亚洲华尔街日报》组织评选的“亚洲企业200强”中，海尔集团连续五年荣登“中国内地企业综合领导力”排行榜榜首。

青岛经济技术开发区海尔热水器有限公司是海尔集团发展最快、专业生产热水器的大型骨干企业之一。

公司在青岛经济技术开发区海尔工业园、武汉海尔工业园和重庆海尔工业园各设有生产基地，是目前亚洲最大的热水器生产基地。

其关键设备分别从德国、意大利等国引进。

其中重要设备已经具备了网络化的特点，可以实现计算机远程控制。

海尔电热水器有8年质保。

其他品牌多为5年。

201X年，海尔研制的防电墙技术，解决中国普遍存在的用电环境引发的安全问题，已经成为国际标准;201X年研制的CO安全防护系统，解决了用户使用燃气热水器意外情况下的CO超标的行业难题，获得国家专利;201X年与中科院共同研发的3D速热技术，解决了储水式热水器加热速度慢的行业难题。

二、海尔电热水器使用说明书之安装部分1、检查电路和水路(1)电表安数和总开关安数，分路开关安数与热水器能否匹配。

(2)进户线线径的大小，预留开关插座安数相匹配。

(3)新装修水管水制装置，确保装置无漏水现象。

2、热水器装置前定位(1)依据客户需求，运用便当来装置热水器(初步定位)。