福特体系钣金件常用缩写词讲解
长安福特常用缩写词
长安福特常用缩写词(CP)Confirmation Prototype确认样车Final Status最终状态(J1)Job 1整车投产(PT)P/T Design Complete动力传动系统设计结束PT（P/T）Power Train动力传动系统(ST)Surface Transfer表面参数传递Change Cut-Off更改完成Launch Readiness投产准备就绪Launch Sign-Off投产验收Program Approval项目批准Proportions & Hardpoints比例与固定点Product Readiness产品准备就绪Pre Milestone 1SI前里程碑1Pre Milestone 2SI前里程碑2Strategic Confirmation策略确认Strategic Intent策略意向Strategic Planning策略计划(SP)Structural Prototype样车结构(TTO)Tool Try-Out工装设备试运行Global 8D Eight disciplinary ActionsG8D(福特公司解决问题的标准方法)14DMore Detailed than Global 8D (used to containand resolve stop-shipment/recall problems)更详细的细节(包括并解决停止运货/召回问题)1MIS One Month in Service投入使用1个月1PP First Production Proveout第一次试生产2PP Second Production Proveout第二次试生产3MIS Three Months in Service投入使用3个月4P Production Process Proveout Program生产程序验证项目AAA American Automobile Association美国汽车工业联合会ABS Affordable Business Structure可承受商业结构ABS Anti skid brake system防抱死制动系统AIAG Automotive Industry Action Group 机动车工业行动小组AIC Accelerated Implementation Centre快速实施中心AIM Automated Issues Matrix问题结构图AIMS Automated Issues Matrix System问题结构图系统AME Advanced Manufacturing Engineering先进制造工艺AMPPE Advanced Manufacturing Pre-Program Engineering 先进项目前制造工艺ANOVA Analysis of Variance多样性分析AP Attribute Prototype设计样车APEAL Automotive Performance Execution and Layout机动车性能实施与规划APQP Advanced Product Quality Planning先进产品质量计划ASQ American Society for Quality美国质量协会AV Appraiser Variation评估者的多样性AVT Advance Vehicle Technology先进车辆技术AWS Analytical Warranty System分析性的保修系统AXOD Automatic Transaxle Overdrive Transmission自动变速驱动桥超速档传动系B&ABody & Assembly Operations (New Term: VehicleOperations)车身与组装操作(新术语:车辆操作)BCG Business Consumer Group消费者工作组BIC Best in Class等级中的最佳BIS Body Shop Information System车身工作间信息系统BLI Business Leadership Initiative领导层初始意向BOM Bill OfMaterials零件清单BTB Bumper-to-Bumper保险杠到保险杠BTS Build-To-Schedule按日程建造BUR Business Unit Review业务小组讨论CAS Capacity Analysis Sheet能力分析表C/E Cause & Effect成因及影响CA Customer Attribute消费者特性CAD Computer Aided Design计算机辅助设计CAE Computer Aided Engineering计算机辅助工程CAP Corrective Action Plan纠正行动计划CBG Consumer Business Group消费者业务小组CB Continuous Build连续性生产CC Critical Characteristic评价特性CC Courtesy Copy抄送CC Carbon Copy副本CCC Customer Concern Classification客户问题分类CCC China compulsory certification中国强制认证CDS Component Design Specification零件设计参数CET Campaignable Events Team召回情况小组CETs Common External Tariff普通关税CETP Corporate Engineering Test Procedures公司工程测试程序CFR Constant Failure Rate连续故障率CHFCIM Computer Integrated Manufacturing计算机综合制造CIWG Continuous Improvement Work Group持续改进工作组CL Centerline中心线CMM Coordinate Measuring Machine协调测量设备CMMS Common Material Management System通用材料管理系统CMMS3Common Manufacturing Management System-3通用制造管理系统-3Code X Pre-build focusing on exterior components制造前关注的外部零件Code Y Pre-build focusing on interior components制造前关注的内部零件CP Cost plan(马自达用语)由ECN引起的价格变动估计CP Common Position通用位置CP Confirmation prototype确认样车（FORD 时间节点）C p Relates the allowable spread of thespecification limits to the measure of theactual variation of the process.将参数限制允许限度下的展开与程序实际多样性联系起来CPE Chief Program Engineer首席项目工程师C pk Measures the process variation with respect tothe allowable specification, and takes intoaccount the location of the process average测量程序的多样性并将其考虑到程序平均性的位置中CPU Cost Per Unit单位成本CQDC Corporate Quality Development Center公司质量开发中心CQIS Common Quality Indicator System一般质量指标系统CR Concern Responses问题回复CRT Component Review Team零件讨论组CSA Corporate Security Administrator公司安全管理员CSI Customer Service Index客户服务指数DCO Duty Cycle Output责任循环结果DCP Dynamic Control Planning动态控制计划DDL Direct Data Link直接数据连接Df Degrees of Freedom自由度DFA Design for Assembly总成设计DFM Design for Manufacturability制造能力设计DFMEA Design Failure Mode Effects Analysis故障模式影响分析设计DFR Decreasing Failure Rate故障下降率DMA Database Maintenance Administrator数据库维护管理人员DOE Design of Experiment试验设计DOM Dealer Operations Manager经销商业务经理DP Design Parameters参数设计DQR Durability Quality and Reliability耐久性质量与可靠性DTD Dock to Dock码头至码头DTD Design to Delivery设计到交付DCV Design Confirmation Vehicle设计确认车DV Design Verification设计验证DVM Design Verification Method设计验证方式DVP Design Verification Plan设计验证计划Design Verification Process and Production设计验证程序和产品验证DVP&PVValidationDVP&R Design Verification Plan & Report设计验证计划和结果DVPR Design Verification & Product Reliability设计验证和产品可靠性DVPV Design Verification and Process Verification设计验证和程序验证EAO European Automotive Operations欧洲机动车协会EASI Engineering And Supply Information工程和供应信息ECAR Electronic Connector Acceptability Rating电子连接接受比率EDI Electronic Data Interchange电子数据交换EESE Electrical and Electronic Systems Engineering电力及电子系统工程EMM Expanded Memory Manager扩展内存管理器EMS Environmental Management System环境管理系统EOL End of Line线的端点EQI Extraordinary Quality Initiative特别初始质量ES Engineering Specifications工程参数ESI Early Supplier Involvement早期供应商参与ESP Extended Service Plan延期服务计划ESTA Early Sourcing Target Agreement早期选点目标协议ESWP Early Sourcing Work Plan早期选点工作计划EV Equipment Variation设备变更F&T Facility & Tooling工装设备FACT Facilitation and Certification Training简易化及认证培训FASS Field Action/Stop Shipment区域行动/停止运货区域行动/停止运货(优先使用缩FA/SS Field Action/Stop Shipment (Preferred Acronym)写)FAO Ford Automotive Operations福特机动车协会FAP Ford Automotive Procedure福特机动车程序FAQ Frequently Asked Questions常见问答FCPA Ford Consumer Product Audit福特客户产品审核FCSD Ford Customer Service Division福特客户售后服务分枝机构FDVS Ford Design Verification System福特设计验证系统FER Fresh Eyes Review其它行业人员论证FER Final Engineering Review最终工程论证FEU Field Evaluation Unit区域评估组FIFO First in First Out先进先出FMEA Failure Mode Effects Analysis故障模式影响分析FMVSS Federal Motor Vehicle Safety Standards美国联邦机动车安全标准FPDS Ford Product Development System福特产品开发系统FPS Ford Production System福特生产系统FPSI Ford Production System Institute福特产品系统学院FPS IT Ford Production System Information Technology福特产品系统信息技术FOB Ford of Britain福特英国FQRs Frequent Quality Rejects经常性质量不合格品FR Functional Requirements功能要求FAO (福特机动车运作) 可靠性指FRG FAO Reliability Guide导FS Final Sign-off最终验收FSIC Ford System Integration Council福特系统综合委员会FSN Ford Supplier Network福特供应商网络FSS Full Service Suppliers全方位服务供应商FTDC Fairlane Training and Development Center培训和发展中心FTEP Ford Technical Educational Program福特技术培训项目FTT First Time Through首次通过FUNC-APPRV Functional Approvals功能批准FVEP Finished Vehicle Evaluation Program下线车辆评估项目GAP Global Architecture Process全球建筑设计程序GC Global Craftsmanship全球技术工艺GCARS Global Craftsmanship Attribute Rating System全球技术特性评分系统GCEQ Global Core Engineering Quality全球核心工程质量GEM Generic Electronic Module通用电子模块GIS1Global Information Standards全球信息标准Global Prototype Inventory Requisition andGPIRS全球样车库存及控制安排SchedulingGPP Global Parts Pricing全球零件定价GQRS Global Quality Research System全球质量调查系统GRC UN-ECE Group des Raporteurs de Ceintures欧盟 ECE 安全带规划小组GRC Government Regulations Coordinator政府法规协调员GR&R Gage Repeatability and Reproducibility量具重复性和再现性GRVW Gross Vehicle Weight车辆质量GSDB Global Supplier Database全球供应商数据库GSSM Global Sourcing Stakeholders Meeting全球选点股东大会GYR Green-Yellow-Red绿-黄-红HB Homologation Build法规车制造HI High-Impact重大影响HIC High-Impact Characteristics重大影响特性HR Human Resources人力资源HTFB Hard Tooled Functional Build成形机功能建造HVAC Heating Ventilating and Air Conditioning加热通风和空调ICA Interim Containment Action过渡性补救措施ICCD Intensified Customer Concern Database强化的客户问题数据库ICCD CRSIntensified Customer Concern Database ConcernResolution Specialist 强化的客户问题数据库解决问题专员IE Industrial Engineer产业工程师IFR Increasing Failure Rate 故障率增长ILVS In-Line Vehicle Sequencing车辆顺序IM Industrial Materials工业材料IP Instrument Panel仪表板IPD In Plant Date进厂日IQ Incoming Quality进货质量IQS2Initial Quality Study初始质量研究IR Internal Reject内部不合格品ISO International Organization for Standardization国际标准化组织ISPC In-Station Process Controls过程质量控制JIT Just in Time及时JPH Jobs Per Hour每小时工作量JSA Job Safety Analysis工作安全分析PSW (零件质量合格验收) 未做好KKK PSW not ready for inspection检测准备KLT Key Life Test关键使用寿命测试KO Kickoff起动LCL Lower Control Limit低控制限值LDEM Lean Design Evaluation Matrix设计评估表LOA Letter of Agreement协议书LP&T Launch Planning & Training投产计划和培训LR Launch Readiness投产准备就绪LRR Launch Readiness Review投产准备就绪论证LS Launch Sign-Off投产验收LSL Lower Specification Limit低参数限制LTDB Light Truck Data Base轻型卡车数据库MBJ1Months Before Job One Job1（投产）前1个月MBO Manufacturing Business Office制造办公室ME Manufacturing Engineering制造工程MIS Months in Service使用中的月份MMSA Material Management System Assessment物料管理系统评定MP Mass Production批量生产MP&L Materials, Planning and Logistics材料、计划与物流MPPS Manufacturing Process Planning System制造程序计划系统MOD Module模块MRB Material Review Board物料论证板MRD Material Required Date物料要求到厂日MS Material Specifications物料参数MS3(MSIII)Material Supply Version III物料供应（第三版）MTC Manage the Change管理变更MY Model Year年度车型NAAO North American Automotive Operations北美汽车工业协会NFM Noise Factor Management噪声管理NIST National Institute of Standards and Testing全国标准和测试协会NMPDC New Model Program Development Center新车型项目开发中心Nova C New Overall Vehicle Audit新车总评审NPPR New Program Product Review供应商技术支持NTEI New Tooled End Items新工具加工成品NVH Noise, Vibration, Harshness噪声、振动、操纵平顺性OCM Operating Committee Meeting工作委员会会议OEE Overall Equipment Efficiency总体设备效率OEM Original Equipment Manufacturer设备最初制造厂ONP Owner Notification Program车主告知程序OS Operator Safety操作者安全OTG Open to Go可进行P Diagrams Parameter Diagrams参数图表PA Program Approval项目批准PAG Premier Automotive Group首要机动车项目组PAL Project Attribute Leadership项目特性领导层PAT Program Activity Team, Program Attribute Team, 项目促进小组、项目特性小组和or Program Action Team项目行动小组PCA Permanent Corrective Action持续改进行动PCF Parts Coordination Fixture零件夹具验证PCI Product Change Information产品变更信息PD Product Development产品开发PDL Program Design Language项目设计语言PD Q1Product Development Q1产品开发Q1PDN2Phased Data NotificationPDSA Plan, Do, Study, Act计划、实践、研讨、实施PFMEA Process Failure Mode Effects Analysis程序故障模式影响分析PI Process Improvement程序改进PIPC Percentage of P pk Indices Process Capable P pk指数程序能力百分比Percentage of Inspection Point That SatisfyPIST满足公差要求的检查点百分比TolerancePM Program Manger项目经理PMA Project Management Analyst项目管理分析PMT Program Management Team or Program Module T eam 项目管理组或项目模式组PO Purchase Order采购订单POC Point of Contact联系点POT Process Ownership Team程序所有者小组P p Process Potential程序潜力PP Pilot ProductPP&T Product Planning & Technology产品计划和技术PPAP Production Part Approval Process生产零件批准程序P pk Process Capability程序能力PPC Product Planning Committee产品计划委员会PPL Program Parts List项目零件清单PPMParts per Million (applied to defectiveSupplier parts)零件的百万分比率（适用于供应商不合格零件）PPPM Program and Pre-Production Management程序和投产前管理PR Public Relations公共关系PR Product Requirement产品要求PR Product Readiness Milestone产品就绪时间节点PSO Production Standard Order制造标准订单PSS Private Switching Service私人转接服务PST Program Steering Team项目指导小组PSW Part Submission Warrant零件质量合格验收PTO Powertrain Operations传动系统操纵件PTR Platinum Resistance Thermometer铂金电阻温度计PV Production Validation产品验证PV Process Variables程序变更PV Part Variation零件变更PVBR Prototype Vehicle Build Requirements样车制造要求PVM Production Validation Method产品验证方法PVP Powertrain Validation Program 传动系统验证程序PVT Product Vehicle Team or Plant Vehicle Team产品车辆组或工厂车辆组QA Quality Assurance质量保证QC Quality Control质量控制QCT Quality Cost Timing质量成本时机选择QFD Quality Function Deployment质量功能配备QFTF Quality Focused Test Fleet质量节点测试行动组QLS Quality Leadership System质量领导体系QMS Quality Management System质量管理体系QOS Quality Operating System质量运作体系QOE Quality of Event质量事件QPM Quality Program Manager质量项目经理QPS Quality Process System质量程序系统QR Quality Reject质量不合格QS-9000Quality Systems – 9000质量体系-9000Quality System Assessment for ProductQSA-PD产品开发质量体系评估DevelopmentQTM Quality Team Member质量小组成员QVA Quality-Focused Value Analysis Workshop车间质量重点价值分析R Range范围RFQ Request For Quotation寻求报价R&M Reliability and Maintainability可靠性及可维护性RMS Resource Management System资源管理系统R&R Repeatability and Reproducibility重复性和再现性R&R Roles and Responsibilities职务与责任R&VT Research & Vehicle Technology研究与车辆技术R/1000Repairs per thousand修理千分率RAP Remote Anti-theft Personality module 防盗遥控器个性化模式Robust Engineering Design Process Enabler积极的工程设计程序计划REDPEPRProjectRIE Reliability Improvement Engineer可靠性改进工程师ROA Return on Assets资产回报率ROCOF Rate of Occurrence of Failure故障发生率RPN Risk Priority Number优先处理风险号码RRCL Reliability and Robustness Check List可靠性与强有力的核对表RRDM Reliability and Robustness Demonstration Matrix可靠性与强有力的演示图表RRR PSW rejected PSW (零件质量合格验收) 不合格RWUP RealWorld Usage Profile现实生活使用记录S Standard deviation标准偏差s2Variance多样性SC Significant Characteristics重要特性Significant Characteristics/CriticalSCs/CCs重要特性/评价特性CharacteristicsSCAC Supplier Craftsmanship Advisory Committee供应商技术顾问委员会SCTs Strategic Commodity Teams策略性商品组SDS System Design Specifications系统设计参数SDS Subsystem Design Specification子系统设计参数SEVA Systems Engineering Value Analysis系统工程价值分析Senko Drawing先行图SHARP Safety and Health Assessment Review Process安全和健康评估讨论程序SI System International des Unit国际单位制SIM Supplier Improvement Metrics供应商改进步骤SMART Synchronous Material and Replenishment Trigger同步物料与补给触发器SME Subject Matter Expert主题专家SMF Synchronous Material Flow同步物料流程SOW Statement of Work工作陈述SP Support PlanSP/AP Structural Prototype/Attribute Prototype结构原形/特性原形SP&PI Strategic Process & Product Improvement策略性程序和产品改进SPC Special Product Committee特殊产品委员会SPC Statistical Process Control统计程序控制SPROM Sample Promise Date承诺的样品到货日SREA Supplier Request for Engineering Approval供应商要求工程批准SRI Supplier Responsible Issues供应商责任SSI Sales Satisfaction Index销售满意度指标SSM Strategic Sourcing Meeting策略选点会议ST Surface Transfer表面转移STA Supplier Technical Assistance供应商技术支持STARS Supplier Tracking and Reporting System供应商跟踪及汇报系统SVC Small Vehicle Center小型车中心TA Target Agreement目标协议TB Training Build训练制造TAP Target Achievement Plan目标完成计划TCM Total Cost Management 总成本管理TED Things Engineers Do工程师任务TEG Tooling and Equipment Group工装及设备组TEM Total Equipment Management全部设备管理TGR Things Gone Right事态发展正确TGW Things Gone Wrong事态发展错误TIS Time in Service服务期限TOC Table of Contents目录TPM Total Productive Maintenance全部生产维护TPPS Torque Process Potential Study扭矩程序潜力研究TQC True Quality Characteristics真实质量特性TRIZ (Russian)Theory of Inventive Problem Solving创造性解决问题的理论(俄罗斯) TRMC Timing, Release and Material Control (also 时效性、发布和物料控制（同known as Tar-Mac)Tar-Mac）TS-16949Technical Specification – 16949技术规范-16949 TSP Technical Skills Program技术性技能项目TTO Tool Try Out工装试运行UCL Upper Control Limit上限控制USL Upper Specification Limit参数上限V/C Very or Completely Satisfied非常或完全满意VC Vehicle Center汽车中心VC BuyerVehicle Center Buyer (now Consumer BusinessGroup Buyer)车辆中心客户（现在为商务集团购买客户）VDI Vehicle Dependability Index车辆可靠性指标VDS Vehicle Design Specifications车辆设计参数VDS Vehicle Descriptor Section车辆描述组VER Vehicle Evaluation Ratings车辆评估等级VFG Vehicle Function Group车辆功能组VIN Vehicle Identification Number车辆识别代码VLD Vehicle Line Director车辆生产线总监VO Vehicle Office车辆办公室VO Vehicle Operations车辆运作VOGO Vehicle Operations General Office车辆运作综合办公室VP Vice President副总裁VPMC Vehicle Project Management Coordinator车辆项目管理协调员VPP Vehicle Program Plan车辆项目计划VQL Vehicle Quality Level车辆质量级别VQR Vehicle Quality Review车辆质量研讨VRT Vehicle Review Team车辆研讨小组VRT Variability Reduction Team减少差异小组VRT Vehicle Reduction Team车辆减产小组WAS Work Analysis Sheet工作分析表WCR Worldwide Customer Requirements全球客户需求WERS Worldwide Engineering Release System全球工程发布系统WIP Work In Progress进行中的工作WMI World Manufacturing Identifier世界制造商识别代码WPRC Warranty Parts Return Center维修部件回收中心Potential Significant and CriticalYS/YC潜在的重要和评价特性CharacteristicsRemark: Editor adds the content in shadow. 备注：阴影部分的内容为编者增加。
长安福特常用缩写词
CSA
Corporate Security Administrator
公司安全管理员
CSI
Customer Service Index
客户服务指数
DCO
Duty Cycle Output
责任循环结果
DCP
Dynamic Control Planning
动态控制计划
DDL
Direct Data Link
DVP
Design Verification Plan
设计验证计划
DVP&PV
Design Verification Process and Production Validation
设计验证程序和产品验证
DVP&R
Design Verification Plan & Report
设计验证计划和结果
产品准备就绪
<PS1>
Pre<SI> Milestone 1
SI前里程碑1
<PS2>
Pre<SI> Milestone 2
SI前里程碑2
<SC>
Strategic Confirmation
策略确认
<SI>
Strategic Intent
策略意向
<SP>
Strategic Planning
策略计划
(SP)
制造前关注的外部零件
Code Y
Pre-build focusing on interior components
制造前关注的内部零件
CP
Cost plan(马自达用语)
汽车行业常用英文术语缩写
汽车行业常用英文术语缩写汽车行业常用英文术语缩写词与中文解释1PP- First Phase of Production Prove-Out 第一次试生产4S Sale, Spare part零配件, Service, Survey信息反馈ABS Anti-lock Braking SystemAIAG 美国汽车联合会Benchmark Data 样件资料CB- Confirmation Build 确认样车制造CC- Change Cutoff 设计变更冻结Characteristics Matrix 特性矩阵图COD Cash on Delivery 货到付现预付货款(T/T in advance) CPO Complementary Parts OrderCUV Car-Based Utility VehicleERP Enterprise Resource PlanningIPO Individual Parts OrderISIR Initial Sample Inspection ReportJIT Just In TimeKO Kick-offLP－Lean Production 精益生产LS Launch SupportMPV Multi-Purpose Vehicle 多用途汽车MTP- Make to print supplier 照图加工供应商N/A- Not ApplicableNDA Non Disclosure Agreement 保密协定onetime adj.过去的，从前的PA Program ApprovalPassenger Vehicle 乘用车PPSR Production Preparation Status ReportPQA Process Quality AssurancePR Program ReadinessPre-Launch 试生产price-driven costing 价格引导成本Production Trial Run 试生产Prototype 样件QR- Quality Reject 质量拒收QS Quality StandardPPAP- Production Part Approval Process 生产件批准程序RFQ Request For Quotation询价SOP Start Of ProductionOTS Off T ooling Samples译为“工程样件”即全工装状态下非节拍生产条件下制造出来的样件.用于验证产品的设计能力。
福特常用缩写词 Acronym List
ACRONYM TERM中文译名(CP)Confirmation Prototype确认样车<FS>Final Status最终状态(J1)Job 1整车投产(PT)P/T Design Complete 动力传动系统设计结束PT（P/T）Power Train动力传动系统(ST)Surface Transfer表面参数传递<CC>Change Cut-Off更改完成<LR>Launch Readiness投产准备就绪<LS>Launch Sign-Off投产验收<PA>Program Approval项目批准<PH>Proportions & Hardpoints比例与固定点<PR>Product Readiness产品准备就绪<PS1>Pre<SI> Milestone 1SI前里程碑1<PS2>Pre<SI> Milestone 2SI前里程碑2<SC>Strategic Confirmation策略确认<SI>Strategic Intent策略意向<SP>Strategic Planning策略计划(SP)Structural Prototype样车结构(TTO)Tool Try-Out工装设备试运行G8D(福特公司解决问题的Global 8D Eight disciplinary Actions标准方法)14D More Detailed than Global 8D(used to contain and resolve stop-shipment/recall problems)更详细的细节(包括并解决停止运货/召回问题)1MIS One Month in Service投入使用1个月1PP First Production Proveout第一次试生产2PP Second Production Proveout第二次试生产3MIS Three Months in Service投入使用3个月4P Production Process ProveoutProgram生产程序验证项目AAA American Automobile Association美国汽车工业联合会ABS Affordable Business Structure可承受商业结构ABS Anti skid brake system防抱死制动系统AIAG Automotive Industry Action Group机动车工业行动小组AIC Accelerated ImplementationCentre快速实施中心AIM Automated Issues Matrix问题结构图AIMS Automated Issues Matrix System问题结构图系统AME Advanced ManufacturingEngineering先进制造工艺AMPPE Advanced Manufacturing Pre-Program Engineering先进项目前制造工艺ANOVA Analysis of Variance多样性分析AP Attribute Prototype设计样车APEAL Automotive PerformanceExecution and Layout机动车性能实施与规划APQP Advanced Product QualityPlanning先进产品质量计划ASQ American Society for Quality美国质量协会AV Appraiser Variation评估者的多样性AVT Advance Vehicle Technology先进车辆技术AWS Analytical Warranty System分析性的保修系统AXOD Automatic Transaxle OverdriveTransmission自动变速驱动桥超速档传动系B&A Body & Assembly Operations(New Term: Vehicle Operations)车身与组装操作(新术语:车辆操作)BCG Business Consumer Group消费者工作组BIC Best in Class等级中的最佳BIS Body Shop Information System车身工作间信息系统BLI Business Leadership Initiative领导层初始意向BOM Bill Of Materials零件清单BTB Bumper-to-Bumper保险杠到保险杠BTS Build-To-Schedule按日程建造BUR Business Unit Review业务小组讨论CAS Capacity Analysis Sheet能力分析表C/E Cause & Effect成因及影响CA Customer Attribute消费者特性CAD Computer Aided Design计算机辅助设计CAE Computer Aided Engineering计算机辅助工程CAP Corrective Action Plan纠正行动计划CBG Consumer Business Group消费者业务小组CC Critical Characteristic评价特性CC Courtesy Copy抄送CC Carbon Copy副本CCC Customer Concern Classification客户问题分类CDS Component Design Specification零件设计参数CET Campaignable Events Team召回情况小组CETs Common External Tariff普通关税CETP Corporate Engineering TestProcedures公司工程测试程序CFR Constant Failure Rate连续故障率CIM Computer IntegratedManufacturing计算机综合制造CIWG Continuous Improvement WorkGroup持续改进工作组CL Centerline中心线CMM Coordinate Measuring Machine协调测量设备CMMS Common Material ManagementSystem通用材料管理系统CMMS3Common ManufacturingManagement System-3通用制造管理系统-3Code X Pre-build focusing on exteriorcomponents 制造前关注的外部零件Code Y Pre-build focusing on interiorcomponents制造前关注的内部零件CP Common Position通用位置C p Relates the allowable spread ofthe specification limits to themeasure of the actual variation ofthe process.将参数限制允许限度下的展开与程序实际多样性联系起来CPE Chief Program Engineer首席项目工程师C pk Measures the process variationwith respect to the allowablespecification, and takes intoaccount the location of theprocess average测量程序的多样性并将其考虑到程序平均性的位置中CPU Cost Per Unit单位成本CQDC Corporate Quality DevelopmentCenter公司质量开发中心CQIS Common Quality Indicator System一般质量指标系统CR Concern Responses问题回复CRT Component Review Team零件讨论组CSA Corporate Security Administrator公司安全管理员CSI Customer Service Index客户服务指数DCO Duty Cycle Output责任循环结果DCP Dynamic Control Planning动态控制计划DDL Direct Data Link直接数据连接Df Degrees of Freedom自由度DFA Design for Assembly总成设计DFM Design for Manufacturability制造能力设计DFMEA Design Failure Mode EffectsAnalysis故障模式影响分析设计DFR Decreasing Failure Rate故障下降率DMA Database MaintenanceAdministrator数据库维护管理人员DOE Design of Experiment试验设计DOM Dealer Operations Manager经销商业务经理DP Design Parameters参数设计DQR Durability Quality and Reliability耐久性质量与可靠性DTD Dock to Dock码头至码头DTD Design to Delivery设计到交付DV Design Verification设计验证DVM Design Verification Method设计验证方式DVP Design Verification Plan设计验证计划DVP&PV Design Verification Process andProduction Validation设计验证程序和产品验证DVP&R Design Verification Plan & Report设计验证计划和结果DVPR Design Verification & ProductReliability设计验证和产品可靠性DVPV Design Verification and ProcessVerification设计验证和程序验证EAO European Automotive Operations欧洲机动车协会EASI Engineering And SupplyInformation工程和供应信息ECAR Electronic Connector AcceptabilityRating电子连接接受比率EDI Electronic Data Interchange电子数据交换EESE Electrical and Electronic SystemsEngineering电力及电子系统工程EMM Expanded Memory Manager扩展内存管理器EMS Environmental ManagementSystem环境管理系统EOL End of Line线的端点EQI Extraordinary Quality Initiative特别初始质量ES Engineering Specifications工程参数ESI Early Supplier Involvement早期供应商参与ESP Extended Service Plan延期服务计划ESTA Early Sourcing Target Agreement早期选点目标协议ESWP Early Sourcing Work Plan早期选点工作计划EV Equipment Variation设备变更F&T Facility & Tooling工装设备FACT Facilitation and CertificationTraining简易化及认证培训FASS Field Action/Stop Shipment区域行动/停止运货FA/SS Field Action/Stop Shipment(Preferred Acronym)区域行动/停止运货(优先使用缩写)FAO Ford Automotive Operations福特机动车协会FAP Ford Automotive Procedure福特机动车程序FAQ Frequently Asked Questions常见问答FCPA Ford Consumer Product Audit福特客户产品审核FCSD Ford Customer Service Division 福特客户售后服务分枝机构FDVS Ford Design Verification System福特设计验证系统FER Fresh Eyes Review其它行业人员论证FER Final Engineering Review最终工程论证FEU Field Evaluation Unit区域评估组FIFO First in First Out先进先出FMEA Failure Mode Effects Analysis故障模式影响分析FMVSS Federal Motor Vehicle SafetyStandards美国联邦机动车安全标准FPDS Ford Product DevelopmentSystem福特产品开发系统FPS Ford Production System福特生产系统FPSI Ford Production System Institute福特产品系统学院FPS IT Ford Production SystemInformation Technology福特产品系统信息技术FOB Ford of Britain福特英国FQRs Frequent Quality Rejects经常性质量不合格品FR Functional Requirements功能要求FAO (福特机动车运FRG FAO Reliability Guide作) 可靠性指导FS Final Sign-off最终验收FSIC Ford System Integration Council福特系统综合委员会FSN Ford Supplier Network福特供应商网络FSS Full Service Suppliers全方位服务供应商FTDC Fairlane Training andDevelopment Center培训和发展中心FTEP Ford Technical EducationalProgram福特技术培训项目FTT First Time Through首次通过FUNC-APPRVFunctional Approvals功能批准FVEP Finished Vehicle EvaluationProgram下线车辆评估项目GAP Global Architecture Process全球建筑设计程序GC Global Craftsmanship全球技术工艺GCARS Global Craftsmanship AttributeRating System全球技术特性评分系统GCEQ Global Core Engineering Quality全球核心工程质量GEM Generic Electronic Module通用电子模块GIS1Global Information Standards全球信息标准GPIRS Global Prototype InventoryRequisition and Scheduling全球样车库存及控制安排GPP Global Parts Pricing全球零件定价GQRS Global Quality Research System全球质量调查系统GRC UN-ECE Group des Raporteursde Ceintures欧盟 ECE 安全带规划小组GRC Government RegulationsCoordinator政府法规协调员GR&R Gage Repeatability andReproducibility量具重复性和再现性GRVW Gross Vehicle Weight车辆质量GSDB Global Supplier Database全球供应商数据库GSSM Global Sourcing StakeholdersMeeting全球选点股东大会GYR Green-Yellow-Red绿-黄-红HI High-Impact重大影响HIC High-Impact Characteristics重大影响特性HR Human Resources人力资源HTFB Hard Tooled Functional Build成形机功能建造HVAC Heating Ventilating and AirConditioning加热通风和空调ICA Interim Containment Action过渡性补救措施ICCD Intensified Customer ConcernDatabase强化的客户问题数据库ICCD CRS Intensified Customer ConcernDatabase Concern ResolutionSpecialist强化的客户问题数据库解决问题专员IE Industrial Engineer产业工程师IFR Increasing Failure Rate故障率增长ILVS In-Line Vehicle Sequencing车辆顺序IM Industrial Materials工业材料IP Instrument Panel仪表板IPD In Plant Date进厂日IQ Incoming Quality进货质量IQS2Initial Quality Study初始质量研究IR Internal Reject内部不合格品ISO International Organization forStandardization国际标准化组织ISPC In-Station Process Controls过程质量控制JIT Just in Time及时JPH Jobs Per Hour每小时工作量JSA Job Safety Analysis工作安全分析KKK PSW not ready for inspection PSW (零件质量合格验收) 未做好检测准备KLT Key Life Test关键使用寿命测试KO Kickoff起动LCL Lower Control Limit低控制限值LDEM Lean Design Evaluation Matrix设计评估表LOA Letter of Agreement协议书LP&T Launch Planning & Training投产计划和培训LR Launch Readiness投产准备就绪LRR Launch Readiness Review投产准备就绪论证LS Launch Sign-Off投产验收LSL Lower Specification Limit低参数限制LTDB Light Truck Data Base轻型卡车数据库MBJ1Months Before Job One Job1（投产）前1个月MBO Manufacturing Business Office制造办公室ME Manufacturing Engineering制造工程MIS Months in Service使用中的月份MMSA Material Management SystemAssessment物料管理系统评定MP&L Materials, Planning and Logistics材料、计划与物流MPPS Manufacturing Process PlanningSystem制造程序计划系统MOD Module模块MRB Material Review Board物料论证板MRD Material Required Date物料要求到厂日MS Material Specifications物料参数MS3(MSIII)Material Supply Version III物料供应（第三版）MTC Manage the Change管理变更MY Model Year年度车型NAAO North American AutomotiveOperations北美汽车工业协会NFM Noise Factor Management噪声管理NIST National Institute of Standardsand Testing全国标准和测试协会NMPDC New Model Program DevelopmentCenter新车型项目开发中心Nova C New Overall Vehicle Audit新车总评审NTEI New Tooled End Items新工具加工成品NVH Noise, Vibration, Harshness 噪声、振动、操纵平顺性OCM Operating Committee Meeting工作委员会会议OEE Overall Equipment Efficiency总体设备效率OEM Original Equipment Manufacturer设备最初制造厂ONP Owner Notification Program车主告知程序OS Operator Safety操作者安全OTG Open to Go可进行P Diagrams Parameter Diagrams参数图表PA Program Approval项目批准PAG Premier Automotive Group首要机动车项目组PAL Project Attribute Leadership项目特性领导层PAT Program Activity Team, ProgramAttribute Team, or Program ActionTeam项目促进小组、项目特性小组和项目行动小组PCA Permanent Corrective Action持续改进行动PCI Product Change Information产品变更信息PD Product Development产品开发PDL Program Design Language项目设计语言PD Q1Product Development Q1产品开发Q1PDSA Plan, Do, Study, Act 计划、实践、研讨、实施PFMEA Process Failure Mode EffectsAnalysis程序故障模式影响分析PI Process Improvement程序改进PIPC Percentage of P pk Indices ProcessCapableP pk指数程序能力百分比PIST Percentage of Inspection PointThat Satisfy Tolerance满足公差要求的检查点百分比PM Program Manger项目经理PMA Project Management Analyst项目管理分析PMT Program Management Team orProgram Module Team项目管理组或项目模式组PO Purchase Order采购订单POC Point of Contact联系点POT Process Ownership Team程序所有者小组P p Process Potential程序潜力PP&T Product Planning & Technology产品计划和技术PPAP Production Part Approval Process生产零件批准程序P pk Process Capability程序能力PPC Product Planning Committee产品计划委员会PPL Program Parts List项目零件清单PPM Parts per Million (applied todefective Supplier parts)零件的百万分比率（适用于供应商不合格零件）PPPM Program and Pre-ProductionManagement程序和投产前管理PR Public Relations公共关系PR Product Requirement产品要求PR Product Readiness Milestone产品就绪时间节点PSO Production Standard Order制造标准订单PSS Private Switching Service私人转接服务PST Program Steering Team项目指导小组PSW Part Submission Warrant零件质量合格验收PTO Powertrain Operations传动系统操纵件PTR Platinum ResistanceThermometer铂金电阻温度计PV Production Validation产品验证PV Process Variables程序变更PV Part Variation零件变更PVBR Prototype Vehicle BuildRequirements样车制造要求PVM Production Validation Method产品验证方法PVP Powertrain Validation Program传动系统验证程序PVT Product Vehicle Team or PlantVehicle Team产品车辆组或工厂车辆组QA Quality Assurance质量保证QC Quality Control质量控制QCT Quality Cost Timing质量成本时机选择QFD Quality Function Deployment质量功能配备QFTF Quality Focused Test Fleet质量节点测试行动组QLS Quality Leadership System质量领导体系QMS Quality Management System质量管理体系QOS Quality Operating System质量运作体系QOE Quality of Event质量事件QPM Quality Program Manager质量项目经理QPS Quality Process System质量程序系统QR Quality Reject质量不合格QS-9000Quality Systems – 9000质量体系-9000QSA-PD Quality System Assessment forProduct Development产品开发质量体系评估QTM Quality Team Member质量小组成员QVA Quality-Focused Value AnalysisWorkshop车间质量重点价值分析R Range范围R&M Reliability and Maintainability可靠性及可维护性RMS Resource Management System资源管理系统R&R Repeatability and Reproducibility重复性和再现性R&R Roles and Responsibilities职务与责任R&VT Research & Vehicle Technology研究与车辆技术R/1000Repairs per thousand修理千分率RAP Remote Anti-theft Personalitymodule防盗遥控器个性化模式REDPEPR Robust Engineering DesignProcess Enabler Project积极的工程设计程序计划RIE Reliability Improvement Engineer可靠性改进工程师ROA Return on Assets资产回报率ROCOF Rate of Occurrence of Failure故障发生率RPN Risk Priority Number优先处理风险号码RRCL Reliability and Robustness CheckList可靠性与强有力的核对表RRDM Reliability and RobustnessDemonstration Matrix可靠性与强有力的演示图表RRR PSW rejected PSW (零件质量合格验收) 不合格RWUP Real World Usage Profile现实生活使用记录S Standard deviation标准偏差s2Variance多样性SC Significant Characteristics重要特性SCs/CCs Significant Characteristics/CriticalCharacteristics重要特性/评价特性SCAC Supplier Craftsmanship AdvisoryCommittee供应商技术顾问委员会SCTs Strategic Commodity Teams策略性商品组SDS System Design Specifications系统设计参数SDS Subsystem Design Specification子系统设计参数SEVA Systems Engineering ValueAnalysis系统工程价值分析SHARP Safety and Health AssessmentReview Process安全和健康评估讨论程序SI System International des Unit国际单位制SIM Supplier Improvement Metrics供应商改进步骤SMART Synchronous Material andReplenishment Trigger同步物料与补给触发器SME Subject Matter Expert主题专家SMF Synchronous Material Flow同步物料流程SOW Statement of Work工作陈述SP/AP Structural Prototype/AttributePrototype结构原形/特性原形SP&PI Strategic Process & ProductImprovement策略性程序和产品改进SPC Special Product Committee特殊产品委员会SPC Statistical Process Control统计程序控制SPROM Sample Promise Date承诺的样品到货日SREA Supplier Request for EngineeringApproval供应商要求工程批准SRI Supplier Responsible Issues供应商责任SSI Sales Satisfaction Index销售满意度指标SSM Strategic Sourcing Meeting策略选点会议ST Surface Transfer表面转移STA Supplier Technical Assistance供应商技术支持STARS Supplier Tracking and ReportingSystem供应商跟踪及汇报系统SVC Small Vehicle Center小型车中心TA Target Agreement目标协议TAP Target Achievement Plan目标完成计划TCM Total Cost Management总成本管理TED Things Engineers Do工程师任务TEG Tooling and Equipment Group工装及设备组TEM Total Equipment Management全部设备管理TGR Things Gone Right事态发展正确TGW Things Gone Wrong事态发展错误TIS Time in Service服务期限TOC Table of Contents目录TPM Total Productive Maintenance全部生产维护TPPS Torque Process Potential Study扭矩程序潜力研究TQC True Quality Characteristics真实质量特性TRIZ (Russian)Theory of Inventive ProblemSolving创造性解决问题的理论(俄罗斯)TRMC Timing, Release and MaterialControl (also known as Tar-Mac)时效性、发布和物料控制（同Tar-Mac）TS-16949Technical Specification – 16949技术规范-16949 TSP Technical Skills Program技术性技能项目UCL Upper Control Limit上限控制USL Upper Specification Limit参数上限V/C Very or Completely Satisfied非常或完全满意VC Vehicle Center汽车中心VC Buyer Vehicle Center Buyer (nowConsumer Business Group Buyer)车辆中心客户（现在为商务集团购买客户）VDI Vehicle Dependability Index车辆可靠性指标VDS Vehicle Design Specifications车辆设计参数VDS Vehicle Descriptor Section车辆描述组VER Vehicle Evaluation Ratings车辆评估等级VFG Vehicle Function Group车辆功能组VIN Vehicle Identification Number车辆识别代码VLD Vehicle Line Director车辆生产线总监VO Vehicle Office车辆办公室VO Vehicle Operations车辆运作VOGO Vehicle Operations General Office车辆运作综合办公室VP Vice President副总裁VPMC Vehicle Project ManagementCoordinator车辆项目管理协调员VPP Vehicle Program Plan车辆项目计划VQL Vehicle Quality Level车辆质量级别VQR Vehicle Quality Review车辆质量研讨VRT Vehicle Review Team车辆研讨小组VRT Variability Reduction Team减少差异小组VRT Vehicle Reduction Team车辆减产小组WAS Work Analysis Sheet工作分析表WCR Worldwide CustomerRequirements全球客户需求WERS Worldwide Engineering ReleaseSystem全球工程发布系统WIP Work In Progress进行中的工作WMI World Manufacturing Identifier世界制造商识别代码WPRC Warranty Parts Return Center维修部件回收中心YS/YC Potential Significant and CriticalCharacteristics潜在的重要和评价特性Remark: Editor adds the content in shadow. 备注：阴影部分的内容为编者增加。
福特常用缩写词
AVT
Advance Vehicle Technology
先进车辆技术
AWS
Analytical Warranty System
分析性的保修系统
AXOD
Automatic Transaxle Overdrive Transmission
自动变速驱动桥超速档传动系
B&A
Body & Assembly Operations (New Term: Vehicle Operations)
4P
Production Process Proveout Program
生产程序验证项目
AAA
American Automobile Association
美国汽车工业联合会
ABS
Affordable Business Structure
可承受商业结构
ABS
Anti skid brake system
区域行动/停止运货(优先使用缩写)
FAO
Ford Automotive Operations
福特机动车协会
FAP
Ford Automotive Procedure
福特机动车程序
FAQ
Frequently Asked Questions
常见问答
FCPA
Ford Consumer Product Audit
车身与组装操作(新术语:车辆操作)
BCG
Business Consumer Group
消费者工作组
BIC
Best in Class
等级中的最佳
BIS
Body Shop Information System
常见钣金设计术语中英文对照表
常见钣金设计术语中英文对照表海外工程图面标注说明英文化.------------------------------------------------------------------------ 表一 (工程图面中最常用的专用术语)中文名称英文名称中文名称英文名称向上抽孔 upward extrude压线 score向下抽孔 downward extrude垫脚 locator正面压螺母(钉)(柱) positive pressing nut(screw)(standoff)色拉孔 counter sink反面压螺母(钉)(柱) negative pressing nut(screw)(standoff)向上凸点 upward bump正面色拉孔 positive counter sink向下凸点 downward bump反面色拉孔 negative counter sink向上半剪 upward half-shear向上抽芽孔 upward threaded hole向下半剪 downward half-shear向下抽芽孔 downward threaded hole半剪 half-shear向上反折压平 upward folding and flattening接地标志 ground symbol向下反折压平 downward folding and flattening螺柱 standoff点焊 spot weld穿孔(通孔) through hole丝印 silk screen抽引,抽凸 draw,extrude攻芽 tap冲孔 pierce(piercing)断差 offset变形 deformation压平(两个料厚) hem成形 form(forming)向上抽引,抽凸 upward draw,form凸点 bump向下抽引,抽凸 downward draw,form 拉钉 rivet扩孔 enlarge hole规格大小 specification代号 mark数量 amount加工性质 character备注 instruction表二 (钣金设计中常用的其它术语) 中文名称英文名称中文名称英文名称扩孔 enlarge hole自铆 self-clinching全周压毛边 all round burr平头拉钉 set-head rivet表面处理 finish定位销 dowel pin挂钩 hook平头铆钉 closed-end rivet焊接线 weld line塑料固定栓 fastener,plastic,push-type 压合胶粘剂 pressure sensitive adhesive 尼龙绑带 tie wrap,nylon五金件 hardware泡棉静电导片 gasket,foam,emi贴纸 labeling铍铜静电导片 gasket,becu,emi烤漆 paint圆头螺钉 button-head screw电镀 plating平头螺母 nut flush铭板 nameplate平齐自铆 flush,self-clinching包装 packing紧固螺丝 fix screw铁材零件 sheet metal parts组装 assembly塑料零件 plastic parts凹陷,顶针 sink mark压边铆钉 open-end rivet插孔 jack弹簧螺丝 fsnr,cap,scr表三 (钣金设计中常用的其它术语)中文名称英文名称中文名称英文名称厚度 thick文字,记号 character半冲孔 spring slice角 corner基座 chassis自锁螺母 nut self-clenching承座 bracket轴肘式铆接 toggle lock承架 horsing卡尺 caliper下盖 base ' '打印字模 stamp letter ' '去毛边 deburr ' '反面 farside ' '正面 inside ' '下料 blank(blanking) ' '去除 remove ' '电子/电气术语---中英对照MATERIAL PARTS ENGLISH 汉语1 RESISTOR 电阻R-CARBON 碳膜电阻R-CARBON/METAL FILM 金属碳膜电阻R-CEMENT WIRE 水泥电阻R-CHIP 片状电阻R-COMPOSITION 复合电阻R-FUSIBLE 保险电阻R-THERMISTOR 热敏电阻R-VARABLE 电位器R-VOLTAGE DEPENOENT 压敏电阻R-METAL 金属膜电阻R-CERAMIC 陶瓷电阻R-NETWORK 电阻排2 CONDENSER 电容C-AL 电解电容C-CERAMIC 磁盘电容器C-FILM 涤纶电容C-POLYPROPYLENE 聚丙稀电容器C-ELECTROLYTIC 电解电容器C-NETWORK 组合电容C-POLYESTER 聚脂电容器3 COIL 线圈COIL-DEGAUSSING 消磁线圈COIL-FILTER 滤波线圈COIL-LINE FILTER 线性滤波线圈COIL-LINEARITY 线性线圈COIL CHOKE 扼流圈COIL HORIZ. WIDTH 行宽线圈4 DIODE 二极管ZENER DIODE 稳压二极管PHOTO DIODE 光敏二极管DISCHARE DIODE 放电二极管LIGHT EMITING DIODE 发光二极管SWITCH DIODE 开关二极管COMMUTE DIODE 整流二极管SCHOTTKY DIODE 肖特基二极管5 TRANS 变压器TRANS-AUDIO FREQUENCY 音频变压器TRANS-FLYBACK 回扫变压器（行输出变压器）TRANS-MATCHING 匹配器TRANS-OUTPOT, SOUND 输出变压器（音频输出变压器）TRANS-POWER 电源变压器TRANS-PULSE 脉冲变压器TRANS-SIDE PINCUSHION 枕校变压器TRANS-SWITCHING 开关变压器TRANSFORMER SWITCH 转换变压器TRANS FBT 行输出变压器TRANS-DUMMY 负载变压器TRANS-HORIZ.DRIVE 行推动变压器6 TRANSISTOR 晶体管TR-HIGH-POWER 大功率三极管TR-SMALL SIGNAL 小功率三极管SEMICONDUCTOR TRANSISTOR 半导体晶体管TR-DIGIAL 数字晶体管7 HEAT SINK 散热器8 ACCESSORY 附件9 ADHESIVE-HM, -RBR 粘合剂10 CHASSIS 机芯11 CRT 显象管12 INDUCTOR-AXIAL 轴向电感13 INDUCTOR-LEAD 指示灯导光柱14 KNOB-CONTROL 控制钮15 LENS 镜头16 POWER CORD 电源线17 SENSOR 传感器18 SPEAKER 扬声器19 BADGE-BRAND 商标20 BAG PE 包装袋21 BAG-SHEET 包装袋22 BAND-PP 打包带23 BAND-TIE 打包卡子24 BATTERY-MN 电池25 BRACKET-CRT CRT卡钩27 BRACKET-GRILLE 网窗28 BRACKET-IC IC支架29 BRACKET-LENS 镜头托架30 BRACKET-MIRROR 镜子托架31 BRACKET-PCB PCB托架32 CABINET-BACK,BOT 后下盖33 CABINET-BACK,SIDE 恻下盖34 CABINET-BACK,TOP 后盖，上35 CABINET-FRONT,BOT 前机箱，下36 CABINET-MASK 前框37 CABINET-WOOD,BOT 木箱，下38 CABINET-WOOD,TOP 木箱，上39 CABLE RCA-A/V A/V线41 CASE-PP BOX 吸塑包装42 CASTER 轮子43 CBF IF 同轴电缆44 CBF SIGNAL 信号线45 CLAMPER CORE-CORD 线卡46 CLAMPER CORE-WIRE 线卡47 COMB FILTER 梳状滤波器48 CONNECTOR-HEADER 连接头49 CONNECTOR-SOCKET 连接插座50 CORE-FERRITE 铁氧体电感51 COVER-DUCT 防尘罩52 CRYSTAL-UNIT 晶体53 CUSHION-CRT CRT减振垫54 DEFLECTION YOKE DY，偏转线圈55 DIODE-BRIDGE 硅桥56 DOOR-A/V A/V门58 EYELET 铆钉59 FET-SILICON 场效应管60 FILTER LINE NOISE 线形噪音滤波器61 FILTER-EMI ON BOARD EMI 滤波62 FILTER-EMI SMD EMI 滤波63 FLUX 助焊剂64 FUSE-AXIAL LEAD 轴向保险65 FUSE-HOLDER 保险丝夹66 GREASE-SILICON 硅脂67 GUIDE-FLOW 导流槽68 GUIDE-FRONT 前导轨69 GUIDE-KNOB,CONTROL 控制键导轨70 HEAT SINK 散热器71 HOLDER 托架72 HOLDER-BOX 纸箱扣手73 HOLDER-CABINET,WOOD 木箱托架75 HOLDER-CHASSIS 机芯托架76 HOLDER-CRT CRT托架79 HOLDER-JERSEY 机芯挡卡80 HOLDER-LEG 底挂81 HOLDER-MASTER 主开关架83 HOLDER-RAIL 导轨槽84 HOLDER-SCREEN 屏幕固定架85 HOLDER-SENSOR 传感器拖架86 HOLDER-WIRE 线卡87 IC ASIC IC88 IC HYBRID 厚膜电路89 IC MICOM 控制芯片90 IC-A/D&D/A CONVERTER A/D&D/A 转换92 IC-ANALOG SWITCH 模拟开关IC93 IC-CMOS LOGIC COMS 逻辑IC94 IC-DEF. PROCESSOR 偏转处理IC95 IC-EEPROM 存储器96 IC-ETC. MEMORY 记忆IC97 IC-LCD CONTROLLER LCD 控制IC98 IC-MICROCONTROLLER 微控IC99 IC-NEGA.FIXED REG. 负电压稳压IC 100 IC-OP AMP 输出放大 IC101 IC-PLL 锁相环路IC102 IC-POSI.FIXED REG. 正电压稳压 IC 103 IC-POWER AMP 功放104 IC-PWM CONTROLLER 脉宽调制控制器105 IC-RESET 复位106 IC-SOUND PROCESSOR 伴音处理107 IC- SWITCH REG. 开关调整 IC 108 IC-VERTICAL DEF. 垂直偏转109 IC-VIDEO AMP 视频功放110 IC-VIDEO PROCESS 视频处理111 IC-VIDEO RAM 视频存储112 IC-VIDEO SWITCH 视频开关113 IC-VOL.DETECTOR 电压检测IC 114 IC-VOLTAGE REGULATOR 稳压IC 115 INDICATOR LED 指示灯116 INDUCTOR-RADIAL 径向电感117 INDUCTOR-SMD 贴片电感118 INLAY AV AV说明片119 INLAY-BACK 后盖说明片120 INLAY-COVER 覆盖片121 JACK-PIN 端子122 JACK-VHS S端子123 KNOB CONTROL 控制钮124 KNOB POWER 电源钮125 LABEL-LINE,NO 线体标签126 LABEL-RATING 后盖铭牌127 LEAD CONNECTOR-ASSY 连接线131 MAGNET CONVERGENCE 会聚磁盘132 MANUAL USERS 说明书133 MIRROR-FRONT 前面镜134 MODULE 模块135 MODULE REMOCON 遥控接收头136 OSCILLATOR-CLOCK 时钟振荡器137 PACKING CASE-IN 里箱138 PACKING-CASE,OUT 外箱139 PAD 纸板140 PAD-BOTTOM,EPE EPE底板141 PAD-CROSS 插格142 PAD-PLATE 纸板143 PAD-TYPE 纸板144 PAD- UNICOM UNICOM 板145 PALLET-CKD 纸拍146 PCB-A/V FRONT 前A/V PCB板147 PCB-CONTROL 控制 PCB 板148 PCB-CONVERGENCE MODULE 会聚模块PCB 板149 PCB-CRT CRT 板150 PCB-H/V MODULE 行场模块PCB板151 PCB-MAIN 主板152 PCB-MICOM MICOM 板153 PCB-POWER 电源板154 PCB-POWER S/W 电源开关板155 PCB-VM 速度调制板156 PHOTO-COUPLER 光电耦合器157 PIN-GT,ASSY 接线柱组件158 PIN-STAPLE 一字平卡丁159 RELAY-POWER 继电器160 REMOCON 遥控器161 RESIN HIPS 聚苯乙烯162 SCREW-TAPTITE 自攻螺钉163 SCREW-WOOD 木箱螺钉164 SHEET 包装袋165 SOCKET-CRT CRT管座166 SOLDER-CREAM 焊锡膏167 SOLDER-WIRE 焊锡丝168 SPACER-CAP 橡胶帽169 SPACER-COVER,DUST 防尘罩177 SPEAKER 扬声器178 SPRING ETC-CS 弹簧179 SPRING ETC-WIRE 弹簧180 SUN SCREEN-AG 屏幕182 SWITCH-PUSH 推推开关183 SWITCH-TACT 轻触开关186 TAPE-OPP MASKING 胶带187 THERMISTOR-NTC 热敏电阻-负温度系数188 TUNER 调谐器189 VR-SEMI 半可变电阻190 WASHER 垫片191 WASHER-PLATE 散热器垫片192 WINDOW REMOCON 遥控接收窗193 WIRE-NO SHEATH CU 滤光片194 WIRE-PVC CU 光线196 WARRANTY CARD 联保单。
钣金件术语总结
钣金件术语总结钣金件术语总结总结是把一定阶段内的有关情况分析研究，做出有指导性的经验方法以及结论的书面材料，通过它可以全面地、系统地了解以往的学习和工作情况，因此我们需要回头归纳，写一份总结了。
总结怎么写才能发挥它的作用呢？以下是小编为大家整理的钣金件术语总结，供大家参考借鉴，希望可以帮助到有需要的朋友。
1、剪料：指材料经过剪板机得到矩形工件的工艺过程。
2、下料：指工件经过LASER切割或数控冲床冲裁的工艺过程。
3、落料：指在普通冲床或其他设备上使用模具加工得到产品形状的工艺过程。
4、冲孔：指工件由普通冲床和模具加工孔的工艺过程。
5、折弯：指工件由折弯机成型的工艺过程。
6、成形：指在普通冲床或其他设备上使用模具使工件变形的工艺过程。
7、抽孔：也叫“翻边”，指在普通冲床或其他设备上使用模具对工件形成圆孔边翻起的工艺过程。
8、攻牙：指在工件上加工出内螺纹的工艺过程。
9、扩孔：指用钻头或铣刀把工件上小孔加工为大孔的工艺过程。
10、沉孔：指为配合类似沉头螺钉一类的连接件，而在工件上加工出有锥度的孔的工艺过程。
11、压铆：指采用冲床或油压机把压铆螺母、压铆螺钉或压铆螺母柱等紧固件牢固地压接在工件上的工艺过程12、涨铆：指先将工件沉孔，再采用冲床或油压机把涨铆螺母牢固地压接在工件上的工艺过程。
13、拉母：指采用类似铆接的工艺。
用拉母枪把拉铆螺母（POP）等连接件牢固地连接在工件上的工艺过程。
14、拉铆：指以拉铆枪为工具用拉钉将两个或两个以上工件紧密地连接在一起的工艺过程。
15、铆接：用铆钉将两个或两个以上工件面对面连接在一起的工艺过程，若是沉头铆接，需将工件先进行沉孔。
16、冲凸包：指在冲床或油压机用模具使工件形成凸起形状的工艺过程。
17、冲撕裂：也叫“冲桥”，指在冲床或油压机用模具使工件形成像桥一样形状的工艺过程。
18、冲印：指使用模具在工件上冲出文字、符号或其他印迹的工艺过程。
19、切角：指在冲床或油压机上使用模具对工件角进行切除的工艺过程。
FORD常用缩写翻译
APQP Advanced Product Quality Planning 产品先期策划AIMS Automated Issues Matrix System 自动化问题矩阵系统APR Annual Percentage Rate 年度百分率ASN Advanced Shipping Notice 提前发货通知BIW Body In White 白车身BOM Bill of Material 材料单BP Business Plan 商务计划BU Build Up 组建CC Change Cutoff/Critical Characteristics 量产切换阶段/关键特性CCL Conveyance Contents List 运输货物内容条款清单CCA Covisint connection and Administration convisint连接与管理CDS Component Design Specification 零件设计规格CMMS Common Manufacturing Management System. 共同制造管理系统CP Confirmation Prototype 确认原型CP-C Confirmation Prototype – Craftsmanship 技术确认CP-F Confirmation Prototype - Functional 功能确认CB/IB Continuous Build/Integrated Build 连续安装/整装CPE Chief Program Engineer 主要项目工程师CPSC Corporate Product System Classification 公司产品系统分类DFA Design for Assembly 装配性设计DFM Design for Manufacturing 生产性设计DFMEA Design Failure Mode and Effects Analysis 设计失效模式及后果分析DMAR Design/Manufacturing Assembly Readiness 设计/制造装配准备DV Design Verification 设计确认DVP Design Verification Plan 设计确认计划DVPR Design Verification, Plan and Report 设计确认、计划及报告DVPSOR Design Verification, Plan and Sign-off Report 设计确认、计划及完成报告EAO European Automotive Operations 欧洲汽车运行EASI Engineering and Supply Information 工程及供应资料ESTA Early Sourcing Target Agreement 早期选点目标协议ESWP Early Sourcing Workplan. 早期选点工作计划FAP Ford Automotive Procedure 福特汽车程序FCPA Ford Consumer Product Audit 福特消费者产品评审FDVS Ford Design Verification System 福特设计确认体系FEU Field Evaluation Unit 现场评估单元FMA Failure Mode Analysis 失效模式分析FMEA Failure Mode Effects Analysis 失效模式效果分析FPDS Ford Product Development System 福特产品开发系统GEMSS Global Engineering Management Support System 全球工程管理支持系统GSEC Global Supplier Electronic Communication 全国供应商电子信息系统HTFB Hard Tooling Functional Build 工装功能验证IR Implementation Ready 准备实施IPD In Plant Date 交货日期J1 Job#1 Achieved 达到量产KO Kick-Off 项目启动LR Launch Readiness 投产准备就绪LS Launch Sign Off 投产签收MMSA Material Management System Assessment 物料管理评估系统MP&L Material Planning and Logistics 材料计划及后勤MRD Material Required Date 材料需求日期MY Model Year 模范年OCM Operating Committee Meeting 营业委员会议OPD Ongoing Product Development 制作中产品开发PA Program Approval 项目批准PD Program Definition/Product Development 项目定义/产品开发PFMEA Process Failure Mode and Effect Analysis 过程失效模式及效果分析PH Proportions and Hardpoints 比率和硬点PIST Percentage of Inspection Points Satisfying Tolerance 检测点合格率PMT Program Module Team 项目模块组队POP Pay on production 线上直供PPM Program and Pre-Production Management 项目及生产前管理PR Product Readiness 产品准备PS Final Program Status 最终项目状态PSW Parts Submission Warrant 零件提交保证PV Production Validation/Plan View 生产确认/平面图PVT Plant Vehicle Team 车间车型队QOS Quality Operating System. 质量操作系统QR Quality Reject 质量不合格品R&R Repeatability and Reliability 重复性及可靠性SC Significant Characteristics 重要特性SCM Supply Chain Management 供应链管理SC Strategic Confirmation 战略确认SI Strategic Intent 战略目的SIM Supplier Improvement Metrics 供应商改进指标SOW Satement Of Work 工作表SPC Statistical Process Control 统计过程控制ST Surface Transfer 表面转换STA Supplier Technical Assistance 供应商技术协助TBD To-Be-Determined 待定TGR Things Gone Right 运行正常TGW Things Gone Wrong 运行出错TTO Tool Try-Out 试生产VTTO Vendor Tool Try Out 供应商工装调试VO Vehicle Office/Vehicle Operations 车辆办公室/车辆运行WAM Web Access Module 网络访问模数1PP First Phase of Production Prove-Out 首期生产验证。
常见钣金设计术语中英文对照表
常见钣金设计术语中英文对照表第一篇：常见钣金设计术语中英文对照表表一(工程圖面中最常用的專用術語)中文名稱英文名稱中文名稱英文名稱向上抽孔 upward extrude 壓線 score向下抽孔 downward extrude 墊腳 locator正面壓螺母(釘)(柱)positive pressing nut(screw)(standoff)沙拉孔 counter sink反面壓螺母(釘)(柱)negative pressing nut(screw)(standoff)向上凸點upward bump正面沙拉孔positive counter sink 向下凸點downward bump反面沙拉孔 negative counter sink 向上半剪 upward halt-shear 向上抽芽孔 upward threaded hole 向下半剪 downward halt-shear向下抽芽孔 downward threaded hole 半剪 halt-shear向上反折壓平upward folding and flattening 接地標志 ground symbol向下反折壓平downward folding and flattening 螺柱 standoff 點焊 spot weld 穿孔(通孔)through hole絲印 silk screen 抽引,抽凸 draw,extrude攻芽 tap 沖孔 pierce(piercing)斷差 offset 變形 deformation壓平(兩個料厚)hem 成形 form(forming)向上抽引,抽凸 upward draw,form 凸點 bump向下抽引,抽凸 downward draw,form 拉釘 rivet擴孔 enlarge hole 規格大小 specification代號 mark 數量 amount加工性質 character 備注 instruction表二(鈑金設計中常用的其它術語)中文名稱英文名稱中文名稱英文名稱擴孔enlarge hole 自鉚 self-chinching全周壓毛邊all round burr平頭拉釘 set-head rivet表面處理finish 定位銷 dowel pin挂鉤hook平頭鉚釘 closed-end rivet焊接線 weld line 塑膠固定栓 fastener,plastic,push-type壓合膠粘劑 presure sensitive adhesive 尼龍綁帶 tie wrap,nylon 五金件 hardware 泡棉靜電導片 gasket,foam,emi貼紙 labeling 鈹銅靜電導片 gasket,becu,emi烤漆 paint 圓頭螺釘 button-head screw電鍍 plating平頭螺母 nut flush銘板 nameplate平齊自鉚 flush,self-clinching包裝 packing 緊固螺絲 fix screw鐵材零件 sheet metal parts 組裝 assembly塑膠零件 plastic parts 凹陷,頂針 sink mark壓邊鉚釘 open-end rivet / /插孔 jack / /彈簧螺絲 fsnr,cap,scr / /表三(鈑金設計中常用的其它術語)中文名稱英文名稱中文名稱英文名稱厚度thick 文字,記號charactor半沖孔 spring slice 角 corner基座 chassis 自鎖螺母 nut self-clenching承座 bracket 軸肘式鉚接 toggle lock承架 horsing 卡尺 cali per下蓋 base ' '打印字模 stamp letter ' '去毛邊 deburr ' '反面 farside ' '正面 inside ' '下料 blank(blanking)' '去除 remove ' '第二篇：常见钣金设计术语中英文对照表1常见钣金设计术语中英文对照表海外工程图面标注说明英文化.------------------表一(工程图面中最常用的专用术语)中文名称英文名称中文名称英文名称向上抽孔 upward extrude 压线 score向下抽孔 downward extrude 垫脚 locator正面压螺母(钉)(柱)positive pressing nut(screw)(standoff)色拉孔counter sink反面压螺母(钉)(柱)negative pressing nut(screw)(standoff)向上凸点upward bump正面色拉孔positive counter sink 向下凸点downward bump反面色拉孔negative counter sink 向上半剪upward halt-shear向上抽芽孔upward threaded hole 向下半剪downward halt-shear向下抽芽孔downward threaded hole 半剪 halt-shear向上反折压平upward folding and flattening 接地标志 ground symbol向下反折压平downward folding and flattening 螺柱standoff点焊 spot weld 穿孔(通孔)through hole丝印 silk screen 抽引,抽凸 draw,extrude攻芽 tap 冲孔 pierce(piercing)断差 offset 变形 deformation压平(两个料厚)hem 成形 form(forming)向上抽引,抽凸 upward draw,form 凸点 bump向下抽引,抽凸 downward draw,form 拉钉 rivet扩孔 enlarge hole 规格大小 specification代号 mark 数量 amount加工性质 character 备注 instruction表二(钣金设计中常用的其它术语)中文名称英文名称中文名称英文名称扩孔enlarge hole 自铆 self-chinching全周压毛边all round burr平头拉钉 set-head rivet表面处理finish 定位销 dowel pin挂钩hook平头铆钉 closed-end rivet焊接线 weld line 塑料固定栓 fastener,plastic,push-type压合胶粘剂 presure sensitive adhesive 尼龙绑带 tie wrap,nylon 五金件 hardware 泡棉静电导片 gasket,foam,emi贴纸 labeling 铍铜静电导片 gasket,becu,emi烤漆 paint 圆头螺钉button-head screw电镀plating平头螺母nut flush铭板nameplate平齐自铆 flush,self-clinching包装 packing 紧固螺丝 fix screw铁材零件 sheet metal parts 组装 assembly塑料零件 plastic parts 凹陷,顶针 sink mark压边铆钉 open-end rivet / /插孔 jack / /弹簧螺丝 fsnr,cap,scr / /表三(钣金设计中常用的其它术语)中文名称英文名称中文名称英文名称厚度 thick 文字,记号 charactor半冲孔 spring slice 角 corner基座 chassis 自锁螺母 nut self-clenching承座 bracket 轴肘式铆接 toggle lock承架 horsing 卡尺 cali per下盖 base ' '打印字模 stamp letter ' '去毛边 deburr ' '反面 farside ' '正面 inside ' '下料 blank(blanking)' '去除 remove ' '第三篇：钣金设计及制造常用英语(中英文对照表)钣金英语声明：此资料本人借鉴了网上可查的资料，进行了编辑整。
ford 英语缩写
1PP (First Phase of Production Prove-Out) 第一阶段生产验证AIAG (Automotive Industry Action Group) 车辆工业行动团体AIMS (Automated Issues Matrix System) 自动问题追踪系统APQP (Advanced Product and Quality Planning) 先期产品开发计划AWS (Analytical Warranty System) 索赔分析系统C&E (Cause and Effect) 因果图CAD/CAM (Computer-Aided Design/Computer-Aided Manufacturing) CAD &CAMCC (Critical Characteristic) 关键特性CP (Confirmation Prototype) 验证原型车Cpk (Process Capability Index) 初期制程能力指数CPU (Cost Per Unit) 每台费用CPV (Capacity Planning Volume) 计划产能数量CTQ Critical to Quality 关键特性DCP (Dynamic Control Planning) 动态控制系统DDL (Direct Data Link) 数据直接链接DFMEA (Design Failure Modes & Effects Analysis) 设计不良模式效应分析DMAIC (Define, Measure, Analyze, Improve, Control -- 6 Sigma Problem solving) 定义,量测,分析,改善,管制--六个标准差问题解决方法DPMO (Defect per Million Opportunities) 每百万机会中不良DPU (Defect per Unit) 每台不良DTD (Dock-To-Dock) 码头到码头DVP&R (Design Verification Plan and Report) 设计验证计划与报告ES (Engineering Specifications) 工程规范FCPA (Ford Consumer Product Audit) 福特顾客产品稽核FMEA (Failure Mode and Effects Analysis) 不良模式效应分析FSN (Ford Supplier Network) 福特供货商网络FSP (Ford Supplier Portal) 福特供货商网站FSS (Full Service Supplier) 全服务供货商FTT (First-Time-Through) 首次合格率GAGE R&R (Gage Repeatability & Reproducibility) 量具再生与再现性HIC (High Impact Characteristic) 高影响特性JIT (Just In Time) 及时生产KPIV (Key Process Input Variable) 关键输入变量KPOV (Key Process Output Variable) 关键输出变数LRR (Launch Readiness Review) 上线准备完成审核MP&L (Material Planning and Logistics) 材料规划及物流MS (Material Specifications) 原料规格MSA (Measurement Systems Analysis) 量测系统分析NIST (National Institute of Standards and Technology) 国家技术标准研究院np Chart (Chart for monitoring defective-nonconforming individual products) 不良数管制图OEE (Overall Equipment Effectiveness) 设备综合效率PD (Product Development) 产品开发PEO (Product Engineering Office) 产品工程办公室PFMEA (Process Failure Modes & Effects Analysis) 制程不良模式效应分析PMT (Program Module Team) 计划模块小组PPAP (Production Part Approval Process) 生产性零尽审核流程Ppk (Performance of process) 长期制程能力PSW (Part Submission Warrant) 零件自主保证书PVA (Percent Value Add) 有增值的比例PVT (Plant or Product Vehicle Team) 车辆产品小组QOS (Quality Operating System) 质量操作系统QR (Quality Rejects) 不良拒收RPN (Risk Priority Number) 风险优先系数SC (Significant Characteristic) 重要特性SDS (System Design Specification) 系统设计规格SEI (Software Engineering Institute) 软件工程协会SFMEA (System Failure Mode and Effects Analysis) 系统不良模式效应分析SIM (Supplier Improvement Metrics) 供货商改进指标SMED (Single Minute Change of Die) 换模时间SPC (Statistical Process Control) 统计制程管制SREA (Supplier Request for Engineering Approval) 供货商设变需求申请单STA (Supplier Technical Assistance) 供货商质量辅导TGW (Things Gone Wrong) 造成的错误件TPM (Total Productive Maintenance) 全面生产维护VO (Vehicle Operations) 福特装配厂VOC (Voice of the Customer) 顾客声音WERS (Worldwide Engineering Release System) 全球工程发布体系统YC (Potential Critical Characteristic) 潜在关键特性YRT Rolled Throughput Yield 作业的制程合格件产出YS (Potential Significant Characteristic) 潜在重要特性1PP (First Phase of Production Prove-Out) 第一阶段生产验证AIAG (Automotive Industry Action Group) 车辆工业行动团体AIMS (Automated Issues Matrix System) 自动问题追踪系统APQP (Advanced Product and Quality Planning) 先期产品开发计划AWS (Analytical Warranty System) 索赔分析系统BTS (Build-To-Schedule) 按排程生产C&E (Cause and Effect) 因果图。
常用钣金英文缩写解释
英文1Sheetmetal2Stainless Steel 3Aluminium4M.S.5Galvanized Steel 6Plug Welding 7Spot Welding 8Powdercoating 9Painting10TIG11MIG12Laser Cutting 13Bending14Welding15Sub Assy16Assembly17Material18Specification 19Thickness20Standard21TYP22Note23Comment24Change Required 25ISSUE26Dimension27Tolerance28QTY29Release30Part31Item32Inside33Outside34Surface35Detail36Section37Location英文38Corner39ALL40Length41Wide42Height43BOM44Bracket45Nut46Blot47RIVET48HEXSERT49HUCK Bolt50HUCK Riviet51Spring Washer 52Flat Washer53Dia.54Seal55Deliver56Quality57Project58Work Instruction 59Checklist60Jig61Cover62Thread63Hole64Critical Dimension 65List66LOOM BAR67Electrical box 68Compressor 69Condenser70Evaporator71Case72Plastic常用英文单词解释中文解释钣金简称“SS”，不锈钢。
常用的有SS 304 2B铝，常用的 AL 5052Mid Plate 碳钢钣镀锌钣塞焊点焊喷塑油漆亚弧焊气保焊激光切割折弯焊接分总成简称“ASSY”，组装材料规范厚度标准全称“Typical”，典型的备注备注,解释全称“CR” 工程更改通知版本，另一说法VERSION尺寸公差全称“Quantity" 数量受控零件一项，一条里面外面表面明细截面位置中文解释角所有长度宽度高度材料清单支架螺母螺栓铆钉拉铆螺母HUCK螺栓HUCK铆钉弹垫平垫全称“Diameter”，直径密封发货质量项目全称"WI"，作业指导书检查表工装盖子螺纹孔关键尺寸清单扎线杆电器盒压缩机冷凝器蒸发器壳体塑料。
汽车研发与制造专业英语（福特体系、中英文对照）
汽车研发与制造专业英语（福特体系、中英文对照）1、技术开发概念和定义FPDSFord Product Development System 福特产品开发系统threetype chassis三类底盘inter-citybus长途客车PassengerVehicle 乘用车MPVMulti-PurposeVehicle 多用途汽车SUVSports Utility Vehiclefour-wheeldrive 四轮驱动front-wheeldrive 前轮驱动DFA-Design For Assembly 面向装配的设计toolbox随车工具torque扭矩speedat maximum torque最大扭矩转速shafthorsepower输出马力transientresponse test瞬态响应时间试验FlowChart 流程图NVH-System Noise, Vibration & Harshness 系统噪音,振动及粗糙性VINVehicle Identification Number 车辆识别代码SORStatement of Requirements 技术要求2、设计开发过程sketchfor automobile layout汽车总布置草图automobileassembly drawing汽车总装配图VPP-Vehicle Program Plan 整车项目计划DVPDesign Verification Plan 设计验证计划DVP&RDesign Verification Plan & Report 设计验证计划和结果DVP&RDesign Validate Plan&Report设计验证计划报告DFMEADesign Failure Mode Effects Analysis 故障模式影响分析设计FMEAFailure Mode Effects Analysis 故障模式影响分析GD&T-Geometric Dimensioning & Tolerancing 标准公差GR&RGuage Repeatability&reproducibility量具的重复性和再现性N/A-Not ApplicableNDANon Disclosure Agreement 保密协定PMT-Program Moudle Team 产品模块小组CC-Change CutOff 设计变更冻结SOP：Start-Of-Production3、样件和试生产Prototype样件OTTOK-TO-TOOL 可以开模MRDMaterial Required Date 物料要求到厂日IPDIn Plant Date 进厂日DBDurability Build 样车阶段CP1-Confirmation Prototype 1st 第一次确认样车CP2-Confirmation Prototype 2nd 第二次确认样车CB-Confirmation Build 确认样车制造PVProduction Validation 产品验证TKOT ooling-Kick-Off 工装启动VTTO-Vendor T ool Try-Out 供应商工装验证ProductionTrial Run 试生产TTO-ToolTry Out 工装验证TTOTool Try-Out 工装设备试运行OTSOFF TOOL SAMPLE 用批量生产的工模器具制造出的样件OTSOff-Tooling-Sample 完全工装样件PPProduction Proveout 生产验证1PP-First Phase of Production Prove-Out 第一次试生产PVSProduktions Versuchs Serie 批量试生产PPAP-Production Part Approval Process 生产件批准程序BMGBau-Muster-Genehmigung 产品工程样件性能检验认可VO-Vehicle Operation 主机厂4、质量管理QOSQuality Operating System 质量运作体系QSVQualitaes-Sicherungs-Vereinbarung 质量保证协议QR-Quality Reject 质量拒收APQPAdvanced Product Quality PlanQSQuality StandardSQESupplier Quality Engineer 供方质量工程师FMEAFailure Mode and Effects AnalysisAPQPAdvanced Product Quality Planning 先期产品质量计划PPMParts per Million (applied to defective Supplier parts) 零件的百万分比率（适用于供应商不合格零件）PPAPProduction Part Approval Process 生产件批准程序Pre-PVPre -Production Validation 产品预先验证YC(Potential Critical Characteristic) 潜在关键特性YS(Potential Significant Characteristic) 潜在重要特性ABSAnti-lock Braking SystemANPQPAlliance New Product Quality Procedurespotcheck test抽查试验deliverytest出厂试验SPCStatistical Process Control 统计过程控制Firstarticle inspection首检Self-inspection自检100%inspection全检processaudit巡检outof box audit开箱检验out-goinginspection出货检验in-cominginspection进货检验Routinechecking例行检验Confirming确认检验fulldimension inspection全尺寸检验Reliabilitytest可靠性试验on-lineinspection在线检验off-lineinspection线下检验3C：Customer(顾客导向)、Competition(竞争导向)、Competence（专长导向）4S：Sale, Sparepart零配件, Service, Survey信息反馈8D-8 DisciplineD1：信息收集；8DD2：建立8D小组；D3：制定临时的围堵行动措施，避免不良品流出；D4：定义和证实根本原因，避免再发；D5：根据基本原因制定永久措施；D6：执行和确认永久措施；D7：预防再发，实施永久措施；D8：认可团队和个人的贡献。
福特常用术语缩写词汇编
B&A
Body & Assembly Operations (New Term: Vehicle Operations)
BCG
Business Consumer Group
BIC
Best in Class
BIS
Body Shop Information System
Hale Waihona Puke BLIBusiness Leadership Initiative
CAE
Computer Aided Engineering
CAP
Corrective Action Plan
CBG
Consumer Business Group
CC
Critical Characteristic
CC
Courtesy Copy
CC
Carbon Copy
CCC
Customer Concern Classification
DVP&PV
TERM
Common Material Management System Common Manufacturing Management System-3 Pre-build focusing on exterior components Pre-build focusing on interior components Common Position Relates the allowable spread of the specification limits to the measure of the actual variation of the process. Chief Program Engineer Measures the process variation with respect to the allowable specification, and takes into account the location of the process average Cost Per Unit Corporate Quality Development Center Common Quality Indicator System Concern Responses Component Review Team Corporate Security Administrator Customer Service Index Duty Cycle Output Dynamic Control Planning Direct Data Link Degrees of Freedom Design for Assembly Design for Manufacturability Design Failure Mode Effects Analysis Decreasing Failure Rate Database Maintenance Administrator Design of Experiment Dealer Operations Manager Design Parameters Durability Quality and Reliability Dock to Dock Design to Delivery Design Verification Design Verification Method Design Verification Plan Design Verification Process and Production Validation
2014年福特常用缩写词
1MIS
pOrnoeblMemonst)h in Service
1PP
First Production Proveout
2PP
Second Production Proveout
3MIS
Three Months in Service
4P
Production Process Proveout Program
抄送
Carbon Copy
副本
Customer Concern Classification
客户问题分类
Component Design Specification
零件设计参数
Campaignable Events Team
召回情况小组
Corporate Engineering Test Procedures 公司工程测试程序
AIM
Automated Issues Matrix
AIMS
Automated Issues Matrix System
AME
Advanced Manufacturing Engineering
AMPPE
Advanced Manufacturing Pre-Program Engineering
ANOVA
Defin,Measure,Analyze,Improve,Control— 6 Sigma Problem solving
定义、测量、分析、改 善、管制—六西格马问 题解决方法
Design of Experiment
试验设计
Dealer Operations Manager
经销商业务经理
Design Parameters
ESOW
汽车常用零件中英文名称缩略语
附件2 常用零件名称缩略语缩略语英文全称中文名称[A]AB Anti After Burning 阻燃ABS Absorber 减震器AC Alternating Current 交流电ACCEL Accelerator 加速器ACCSY Accessory 附件ACCUM Accumulate 聚集,累积,存贮ACTR Actuator 传动装置（机构）ADJ Adjusting 调整、调节ADJ Adjustabler 可调的ADPT Adapter 适配器AIS Air Injection System 空气喷射系统ALT Altitude 标高ALTNTR Alternator 交流发电机AMPL Amplifier 放大器ANCH Anchorage 支座ANT Antenna 天线ARMREST Arm Restraint 限制臂ASCD Automatic Speed Control Device 自动变速控制装置ASST Assistant 辅助ASSY Assembly 总成ATCH Attachment 附件AUTO Automatic 自动AUX Auxiliary 辅助的AV Audio Visual 音频和视频& And 和[B]BAL Balance,ing 平衡BAT Battery 蓄电池BCDD Boost Control Deceleration Device 传动控制减速装置BJT Ball Joint 球头销BMPR Bumper 缓冲器，保险杠BOLS Bolster 垫BPT Back Pressure Transducer 后压力传感器BRG Bearing 轴承BRKT Bracket 支架BRTHR Breather 通气装置BUSH Bushing 衬套，轴衬[C] CAC Combined Air 混合空气17缩略语英文全称中文名称CARB Carburetor 化油器CARR Carrier 托架，支座CAT Catalyst 催化剂CD Compact Disc 光盘CHAN Channel 频道CHG Change 改变，变更CHMBR Chamber 舱，盒，容器CLNR Cleaner 清洁器CLP Clamp 夹子CLPSL Collapsible 自动伸缩CLV Clevis U 形夹COL Column 转向柱COLR Collar 垫圈，凸缘COMB Combination 组合COMPL Complete 完全，完整COMPR Compression 压缩，压缩机COMPT Compartment 车厢、隔板COND Condenser 冷凝器，电容器COND Conditioner 调节装置CONN Connecting 接头CONST Construction 结构CONT Control 控制CONV Convertor 转换器CPLG Coupling 联轴器耦合CRG Carriage 车架，客车CRTG Cartridge 支架CSTG Casting 铸件CTNR Counter 计数器CTR Center 中CUSH Cushion,ing 软垫、缓冲垫CYL Cylinder 活塞[D]DAT Digital Audio Tape 数字式录音磁带DBL Double 双的、加倍DC Direct Current 直流电DEF Defroster 除霜器DIAG Diagram 图表DIAPH Diaphragm 膜片、隔板18缩略语英文全称中文名称DIFF Differential 差速器DIST Distributor 分配器、分动器DIV Divider 分配器DLX Deluxe 豪华的DRVR Driver 驾驶员、驾驶DVC Device 装置、设备、图案DWG Drawing 制图、图纸、图样[E]EAI Exhaust Air Induce 二次空气导入装置EAR Emergency Air Relief 紧急放气阀EFE Early Fuel Evaporation 初级燃油蒸发器EGR Exhaust Gas Recirculation 废气再循环ELEC Electric 电气、电子的EMER Emergency 紧急的EMIS Emission 喷射、发射ENG Engine 发动机ESCUT Escutcheon 罩、盖EVAP Evaporator 蒸发器EXH Exhaust 排气管EXP Expander 蒸发器EXP Expansion 膨胀、扩张EXT Extension 拉伸、延伸8TH Eighth 第八[F]FDR Fender 挡泥板、护板、翼子板FIN Finish,er 修整、装饰FLEX Flexible 柔韧性。
福特Ford Motor术语
Ford inverted delta: 倒三角，critical characteristicsCC: critical characteristics，严重度为9和10(零件)。
关键特性。
SC: significant characteristics，严重度为5-8（发生频率为4-10或福特研发批准）。
重要特性。
HIC: high impact characteristics，严重度为5-8，发生频率为4-10。
高影响度特性。
YC: Potential CC，严重度为9和10。
潜在的关键特性。
YS: Potential SC，严重度为5-8。
潜在的重要特性。
OC: Operator Safety，严重度为9和10(过程)。
操作人员安全。
PTC: pass-through characteristics 传递特性CTQ：critical to quality 关键尺寸(J1) Job 1 整车投产（开始生产可向顾客销售的车辆；JOB1投产评审）2/4-WD: Two/four wheel drive 2/4轮驱动APQP: Advanced product quality planning 先期产品质量规划BOM: Bill of material 物料清单CPA: commercial and program agreement 商务项目协议DB: durability build 样车阶段DFMEA：design failure mode effect analysis （针对设计的）潜在失效模式及后果分析DV：design verification 设计验证DVP：design verification plan 设计验证计划ED&T：engineering development and test 工程开发和测试FDJ：final data judgement 最终资料评价（最终数据确认）-- （客户：UP零件设计完成并发布；签署开模申请；工装、检具方案的评审；UN/UP第二次访问计划确认；/ 供应商：完成工装、检具、设备的开发计划；完成工装、检具方案；开模申请提交）FEC：final engineering completion 最终工程完成（最终工程签发）-- （客户：完成需要重新进行的DV试验；所有整车DV试验和公告试验完成；工程问题关闭；完成工程签发；/供应商：完成需重新进行的DV台架试验）FPDS：ford product development system 福特产品开发系统FRG：Ford reliability guideline 福特可靠性指导F2F：face to face 面对面会议GPDS：global product development system 全球产品开发系统GYR：green-yellow-red 绿黄红IPD：In Plant Date 进厂日IPO：individual part order 单个零件订单ISIR：initial sample inspection report 初始样件检查报告JIT：just in time 准时生产，又译实时生产系统（多品种小批量混合生产条件下高质量、低消耗的生产方式即准时生产；追求一种无库存，或库存达到最小的生产系统。
福特常用缩写词解释
Global Quality Improvement Process
– FPS – Ford Production System – FTT – First Time Through – GCQIS – Global Common Quality Indicator System – GEMM – Global Engineering Matters Meeting – GPDS – Global Product Development System – GQRS – Global Quality Research System – HTIS – High Time In Service – IFR – Increasing Failure Rate – IQS – Initial Quality Survey (J. D. Power) – I & MR – Individual Moving Range Control Chart – LTIS – Low Time In Service – LV – Leverage Vehicle Line – MIS – Months In Service – MOP – Months Of Production – M10 – Finished Vehicle Evaluation Program (FVEP) – PCT – Product Commodity Team – PDCA – Plan, Do, Check, and Adjust – PD – Product Development – PDQR – Product Development Quality Review – PIC – Product information Center – PQR – Plant Quality Review – PRT – Problem Review Teams – PVT – Plant Vehicle Team – QB – Quarter Back process – QCS – Quality and Customer Satisfaction – QLS – Quality Leadership System – QOS – Quality Operating System – QPST – Quality Program Steering Team
长安福特英文缩写大全
Rear Entertainment Module
Remote Function Actuators Rear gate/Trunk Module Remote Heating, Ventilation, and Air Conditioning
Module
Column Lock Module
Camera Module Rear
Driver/Dual Climate Control Seat Module
Dual Clutch Transmission Door Control Unit Driver's Door Module Driver's Seat Module Audio Digital Signal Processing Module Dual Variable Camshaft Timing Electronic Automatic Temperature Control
Remote Keyless Entry Rear Lighting Control Module
Steering Angle Sensor Module Steering Column Control Module Satellite Digital Audio Receiver System
Side Obstacle Detection Control Module
随动转向大灯也被称之为自适应大灯 辅助加热器控制模块 智能灯光系统
附件协议接口模块（sync娱乐系统） 全地形控制模块 车身模块 蓄电池接线盒
弯道制动控制系统 中央车辆参数管理 CCM巡航控制模块 电路停用点火模块
F汽车维修技术缩略语英汉对照
F汽车维修技术缩略语英汉对照FF Fahrenheit 华氏(温度)F *Front *Fiele *Force *Farad *Full*Finish *Fine *前*磁场*力*法拉* 满的*加工*精密F/A Fuel-Air Ratio 燃油空气混合比F/B Feedback 回馈,反馈F/B Fuse Block 保险丝盒F/F Front Engine/Front Wheel Drive 前置发动机前轮驱动F/Rly Pnl Fuse/Relay Panel 保险丝/继电器板FA Failure Analysis 故障分析FA First Aid 急救FA Fuel Additives 燃料添加剂FAC Force-Air Cooling 强制风冷FACS Full Auto Choke system 全自动阻门控制系统FAI Fresh Air Intake 新鲜空气进气FAT Factory Acceptance Test 工厂验收试验FB Feed Back Carburetor Control 回馈式化油器控制FB Fuel Bck-Up 备用油FB Feedback 反馈FB Fire Brigade 消防队FB Feight Bill 运货单FBC Feedback Carburetor 回馈式化油器FBP Final Boiling Point 干点(石油产品完全蒸发时的温度) FC Electro-Drive Fan 电动风扇FC Fan Control 风扇控制FC Fuel Cut 断油FC Fuel Cutout 燃料截断装置FC Fuel Consumption 燃油消耗量FCC Facilities Control Consol 机具控制台.设备操纵台FCC Fluidized Catalytic Cracker 流体催化裂化装置FCGA Facility Gauge 设备标准FCO Fuel Cut-Off 断油FCS Fuel Control System 燃油控制系统FCS Fuel Cut Solenoid Valve 断油电磁阀FCT Fan Control Temperature 风扇控制温度FCU Fuel Control Unit 燃油控制装置FCV Fuel Cut Valve 断油阀FCV Fuel Cutout V alve 燃料截断阀FD Face of Drawing 图纸的正面FD Forced Draft 强力通风FD Frequency Doubler 倍频器FD Function Devices 功能器件FDC Fuel Deceleration Control 燃油减速控制FDN Foundation 基础.地基FDV Forward Delay Valve 前置延迟阀FDV Fuel Decel Valve 燃油减速控制阀FE For Example 例如FE/RD Front Engine/Rear Drive 前置发动机-后轮驱动Fed Federal 联邦政府FEM Fuel Economy Meter 省油表FEM Finite Element Method 有限元法FES Fuel Evaporation System 燃料蒸汽控制系统FES Flash Evaporator System 快速蒸发系统FET Field Effect Transistor 场效应晶体管FF Front Engine Front Drive 前置发动机前轮驱动FF Fixed Fee 固定手续费FF Flip-Flop 触发器.突然反向FF Fuel Flow 燃油流量FF Full Figure 全图.全象FFB Fuel Feed Back 供油反馈装置FFCS Fuel Flow Control System 燃料流量控制装置FFOT Ford Fixed Orifice Tube 福特固定限流管FFT Fast Foourier Transform 快速傅立叶变换FGS First Gear Switch 第一挡位开关FI For Instance 例如FI Fuel Injection 汽油喷射FIA Fast Idle Actuator 快怠速执行器FIA Federation Iternational Auomobile 国际汽车联盟FIAC Fast Idle Air Cylinder 快怠速气缸FIAT Fabbrica Italiana Automobile Torino (意大利)菲亚特汽车公司.菲亚特牌(汽车)FIC Fast Idle Cam 快怠速凸轮FICD Fuel Injection Control Device 燃油喷射控制装置FICD Fast Idle Control Device 快怠速控制装置FID Fast Idle Device 快怠速装置FID Flame Ionization Detecter 氧气离子化探测器FIE Fuel Injection Equipment 燃油喷射装置FIO For Information Only 只供参考FIO Free In and Out 不包括装卸费FIP Fuel Injection Pump 燃油喷射泵FIPL Fuel Injector Pump Lever 喷油咀油泵杠杆FIPO Fast Idle Pull Off 快怠速拉开装置FIPOT Fast Idle Dashpot (日产Z系列发动机)快怠速节气门开度控制装置FIPS Fluorescent Indicator Panels 荧光指示仪表板FIR Facility Installation Review 设备安装检查FIR Facility Interference Review 设备干扰检查FIR Fuel Indicator Reading 燃油表读数FIREX Fire Extinguisher 灭火器FISR Fast Idle Solenoid Relay 快怠速电磁阀继电器FL Fixed Load 固定截荷FL Flow Limited 流量限制FL Full Load 满负荷FLC Fluid Link Converter 液体连结转换器FLI Fluid Level Indicator 液面高度指示器FLP Fault Location Panel 故障诊断仪表板Flshr. Flasher 闪光器FLT Full-Load Torque 满截扭矩FLTR Filter 过滤器, 滤清器FLU Fault Location Unit 故障定位设备FM Field Magnet 磁极.场磁铁FM Field Manual 现场手册FM Field Modification 现场修正,现场更改FM Frequency Modulation 调频FMA Failure Mode Analysis 故障模式分析FMEA Failure Mode Effects Analysis 故障模式效应分析FMEM Failure Mode Effects Management 故障模式效应管理FMR Fuel Metering Rod 燃料测量杆FMVSS Federal Motor Vehicle Safety Standard 美国联邦汽车安全标准FNP Fusion Point 熔点.熔化温度Fnt Front 前Fnt WD Front Wheel Drive 前轮驱动FO Fast Operating Relay 快动作继电器FO Firing Order 点火顺序FO Fuel Oil 燃油FOR Fuel Oil Return 燃料油回路FOR Free On Rail 免付铁路运费(运费由发货者负担)FOR Fuel Oil Return 回油管FP Fuel Pump 燃油泵FP Fuel Pump Relay 油泵继电器FP Friction Power (发动机的)摩擦功率FP Feed Pump 供给泵,供油泵FP Flash Point 闪点FP Fire Proof 耐火的,防火的FP Foot-Pound 英尺磅FP Freezing Point 冰点,凝固点FP Film and Paper Condenser 纸绝缘薄膜电容器FP Finished Pieces 完工件,竣工零件FP Fire Plug 消防栓,消防龙头FP Fixed Price 固定价格FP Fully Paid 全部付讫FPC Fuel Pump Controller 燃油泵控制器FPM Fuel Pump Monitor 燃油泵监视器FPR Fuel Pressure Regulator 油压调整阀FPRC Fuel Pressure Regulator Control 调压控制FPRVSV Fuel Pressure Regulator Vacuum本篇文章来源于万博汽车维修技术资料库 资料引用：/car_xl_815.html。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
AND
Addendum
工艺补充
ANOVA
Analysis of Variance
多样性/方差分析法
ANSI
American National Standard Institute
美国国家标准协会
AP
Advanced Purchasing
先期采购
AP
Attribute Prototype
BHF
Blank Holder Force
压边圈力
BHI
Bake Hardening Index
烘烤硬化指数
BIC
Best in Class
等级中的最佳
BMAW
Bare Metal Arc Welding
无保护金属丝电弧焊接
BOL
Bill Of Lading
提货单
BOM
Bill Of Materials
B&A
Body & Assembly Operations (New Term: Vehicle Operations)
车身与组装操作(新术语:车辆操作)
BCCP
Body Construction Control Point
车身结构控制点
BCG
Business Consumer Group
消费者工作组
操作者安全
IH ASSY
In House Assembly
长安福特装配总成
IH
In House Component
长安福特总成
EP/LP
Outsourcing Delivery Level–Assy or Component
交付状态-总成或组件
LP
Local Component or Sub-Assy
关键特性
SC
Significant Characteristic
重要特性
OS
Operator Safty
操作者安全
Phase0
Phase0 (Run at Rate)
节拍验证（模具调试样件合格）
Phase1
Phase1 (Quality Verification)
质量验证阶段
Phase2
Phase2 (Production Verification)
整改需求
CAS
Capacity Analysis Sheet
能力分析表
CAW
Carbon Arc Welding
碳弧焊
CAW-G
Carbon Arc Welding-Gas
气体保护碳弧焊
CBG
Consumer Business Group
消费者业务小组a}iP +#;
CDS
Component Design Specification
附加工程更改
AIAG
Automotive Industry Action Group
机动车工业行动小组
AIMS
Automated Issues Matrix System
问题结构图系统
AME
Advanced Manufacturing Engineering
先进制造工艺
AMPPE
Advanced Manufacturing Pre-Program Engineering
产能要求计划
CRT
Component Review Team
零件审核/讨论小组
CS
Customer Satisfaction
冲压片件
SP
Import Component Or Sub-Assy
进口标件
SP/C
Import Component Or Sub-Assy, Consign to Supplier
供应商采购进口标件
LP/C
Local Component Or Sub-Assy, Consign to Supplier
投产验收
PP
Production Proveout
生产验证
1PP
First Production Proveout
第一次试生产
2PP
Second Production Proveout
第二次试生产
FS
Final Sign-off
最终验收
KO
Kickoff
启动
TT
Tooling Trail
工装验收/焊接生产线正式生产
计算机综合制造
CIP
Continous Improvement Process
持续改进过程
CIWG
Continuous Improvement Work Group
持续改进工作组
CM
Control Means
控制手段
CMA
Central Material Area
中心材料区域
CMM
Coordinate Measuring Machine
企业质量开发中心
CQIS
Common Quality Indicator System
一般质量指标系统yF%e)6
CR
Concern Responses
问题回复
CR&CR
Change Request & Concern Report
变更请求单和问题报告
CRP
Capacity Requirement Planning
先进技术材料工程
ATP
Authority To Proceed
执行授权
AVT
Advanced Vehicle Technology
先进汽车技术
AW
Arc Welding
电弧焊
AWB
Air way Bill Of Lading
空运提单
AWS
Analytical Warranty System
分析性的保修系统
认证标准协会
ASL
Ford Motor Company Approved Source List
福特汽车公司批准货源清单
ASEAN
Association Of Southeast Asian Nations
东盟
ASN
Advanced Shipping Note
提前通知货运单/送货单
ASQ
American Society for Quality
PP
Production Proveout
生产验证
PP
Production Prototype
样件生产
PP
PilotProduction
试生产
1PP
First Production Proveout
首次生产验证
2PP
Second Production Proveout
第二次生产验证
CC
Critical Characteristic
供应商采购本地标件
A AA
American Automobile Association
美国汽车工业联合会
ABS
Affordable Business Structure
可承受商业构架
ABS
Anti skid brake system
防抱死制动系统
ADJ
Adjustment
调整
AEC
Additional Engineering Changes
生产验证阶段
Phase3
Phase3 (Capacity Verification)
产能验证阶段
Bl
Blanking
落料
Dr
Drawing
拉延
Fo
Forming
成形
Tr
Trimming
切边
Fl
Flanging
翻边
UFL
Up Flange
上翻边
Pi
Pierce
冲孔
RST
Restriken
整形
CPI
Cam-Piercing
Average Per Weekly
每周平均产能
AQS
Analysis Of Quality Of Surface
表面质量分析
ARL
Attribute Requirement List
属性要求清单
ASAP
As Soon As Possible
尽可能快地
ASC
Accredited Standard Committee
设计样车
APA
Advanced Program Approval
先期项目批准
APEAL
Automotive Performance Execution and Layout
机动车性能实施与规划H(k-jAO,
APQP
Advanced Product Quality Planning
先进产品质量计划
APW
三坐标测量设备
CMMS
Common Material Management System
通用材料管理系统
CMR
Control and Measurement Report
控制及测量报告
Code X
Pre-build focusing on exterior components
制造前关注的外部零件,oPxt
物料清单
BOP
Bill Of Process
过程清单
BOS
Business Operating System
商业作业系统概述
BIW
Body In White