阳极氧化工艺流程

阳极氧化工艺流程

阳极氧化工艺流程

悬赏分:10 - 解决时间:2007-11-24 21:06

请告诉我一下阳极氧化工艺流程，1，需要知道它的原理和 2，氧化后的产品

特征，3，工艺流程，4，每一个流程的处理方法和每一个流程的原理和每一个流程的时间。

最重要的，怎样来看阳极氧化后的质量好坏，怎样检验,

哪们兄弟正确回复后，我愿意也会追加30-50分，随便乱找的不算～问题补充:

Why no person answer this question?、、

提问者: xy791123 - 二级最佳答案

阳极氧化已经慢慢淘汰了，现在已经升级到了微弧氧化，可以做镁和铝合金产品，原理都是一样，通过有机溶剂做为介质，采用尖端放电，在产品表面生成保护膜，类似於陶瓷层。外观除了一些起跑引起的颜色问题，是很难看出来的，主要通过，盐雾、耐摩擦、电导率、电击穿等测试来判定膜层的好坏。

工艺:除油--水洗--水洗--阳极反应--水洗--封闭--烘烤

铝制品阳极氧化工艺流程

2009-06-10 08:19

铝制品阳极氧化通用的工艺流程如下:

铝工件?上挂具?脱脂?水洗?碱蚀?水洗?出光?水洗?阳极氧化?水洗?去离子水洗?染色或电解着色?水洗?去离子水洗?封闭?水洗?下挂具

对于要求高光亮度的铝制品，可采用如下的工艺流程:

铝工件?机械抛光?脱脂?水洗?中和?水洗?化学或电化学抛光?水洗?阳极氧化?

水洗?去离子水洗?染色或电解着色?水洗?去离子水洗?封闭?水洗?机械光亮铝及铝合金阳极氧化着色工艺流程(图) 标签:铝合金阳极氧化着色工艺流程时间:2008-12-25 10:08:41 点击:2710 回帖:5 上一篇:成功领袖10大思维方式下一篇:业务员是什么意思呀,

and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan.

(7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the

personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the

铝及铝合金阳极氧化着色工艺规程

1、主题内容与适用范围:

本规程规定了铝及铝合金阳极氧化、着色、电泳生产的工艺和操作的技术要求

及规范。

2、工艺流程(线路图)

基材?装挂?脱脂?碱蚀?中和?阳极氧化?电解着色?封孔?电泳涂漆?固化?卸料包装?入库

3、装挂:

3.1装挂前的准备。

3.1.1检查导电梁、导电杆等导电部位能否充分导电、并定期打磨、清洗或修理。 3.1.2准备好导电用的铝片和铝丝。

3.1.3检查气动工具及相关设备是否正常。

3.1.4核对流转单或生产任务单的型号、长度、支数、颜色、膜厚等要求是否

与订单及实物相符。 3.1.5根据型材规格(外接圆尺寸、外表面积等)确定装挂的