DPtech LSW2300系列以太网交换机安装手册v1.2
锐捷RG-S2300系列交换机安装手册

安装手册RG-S2300系列安全接入交换机版权声明福建星网锐捷网络有限公司©2009锐捷网络有限公司版权所有,并保留对本手册及本声明的一切权利。
未得到锐捷网络有限公司的书面许可,任何人不得以任何方式或形式对本手册内的任何部分进行复制、摘录、备份、修改、传播、翻译成其他语言、将其全部或部分用于商业用途。
、、、、、、、、、都是福建星网锐捷网络有限公司的注册商标,不得仿冒。
免责声明本手册依据现有信息制作,其内容如有更改,恕不另行通知,请关注锐捷网络有限公司网站提供的最新信息。
锐捷网络有限公司在编写本手册时已尽力保证其内容准确可靠,但对于本手册中的遗漏、不准确或错误,以及由此导致的损失和损害,锐捷网络有限公司不承担责任目录前言 (5)第一章产品综述 (7)1.1产品简介 (7)1.2RG-S2300产品主要技术指标 (7)1.3RG-S2300系列各款交换机详细介绍 (8)1.3.1 RG-S2328G以太网交换机 (8)1.3.2 RG-S2352G以太网交换机 (11)1.4RG-S2300系列交换机指示灯说明 (13)1.5RG-S2300系列交换机模块简介 (14)1.5.1 M2000-02SFP/GT模块 (15)1.5.2 M3250-STACK模块 (16)第二章安装前的准备 (18)2.1安全性建议 (18)2.1.1 安装系统的安全 (18)2.1.2 搬移的安全 (18)2.1.3 电气安全性 (18)2.1.4 防静电放电破坏 (19)2.1.5 激光安全性 (19)2.2安装场地的要求 (19)2.2.1 通风要求 (19)2.2.2 温度和湿度要求 (19)2.2.3 洁净度要求 (20)2.2.4 抗干扰要求 (21)2.3系统接地要求 (21)2.3.1 安全接地 (21)2.3.2 雷电接地 (21)2.3.3 电磁兼容接地 (21)2.4防雷考虑 (22)2.5EMI考虑 (22)2.6光纤连线注意事项 (22)2.7安装工具要求 (23)第三章产品的安装 (24)3.1安装流程 (24)3.2安装前确认 (24)3.3安装S2300系列交换机 (25)3.3.1 注意事项 (25)3.3.2 将交换机安装到19英寸机柜中 (25)3.3.3 将交换机安装在墙壁上 (25)3.3.4 将交换机安装在桌面上 (26)3.4安装后检查 (26)第四章系统调试 (27)4.1搭建配置环境 (27)4.1.1 配置环境搭建 (27)4.1.2 配置电缆的连接 (27)4.1.3 设置终端参数 (27)4.2上电启动 (30)4.2.1 上电前的检查 (30)4.2.2 上电后的检查(推荐) (30)第五章安装中的常见故障处理 (31)5.1安装故障排查通用流程 (31)5.2常见故障处理 (31)附录A ——连接器和连接介质说明 (33)一、1000BASE-T/100BASE-TX/10BASE-T端口 (33)二、光纤线的连接 (33)附录B ——MINI-GBIC模块说明 (35)一、M INI-GBIC(SFP)模块类型和技术指标 (35)前言感谢您使用锐捷网络交换机,本手册(版本号:V1.02)为您提供了详细的安装指南,可以更加方便您的安装和使用。
DPtech LSW3600-SI系列以太网交换机典型配置手册v1.4

手册版本:v1.4 软件版本:LSW3600-S221S002D013
DPtech LSW3600-SI 系列以太网交换机典型配置手册 v1.4.docx
声 明
Copyright © 2008-2016 杭州迪普科技有限公司版权所有,保留一切权利。 非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本书内容的部分或全部,并不得以 任何形式传播。
格式 意义 表示操作中必须注意的信息,如果忽视这类信息,可能导致数据丢失、功能 失效、设备损坏或不可预知的结果。 表示对操作内容的描述进行强调和补充。
DPtech LSW3600-SI 系列以太网交换机典型配置手册 v1.4.docx
目 录
1 典型配置案例支持的设备型号 .................................................................................................................. 1 2 常用维护命令行介绍 ................................................................................................................................ 1
3 基本二三层转发配置案例 ......................................................................................................................... 9
3.1 二层转发简介 ........................................................................................................................................ 9 3.1.1 配置需求 ................................................................................................................................... 10 3.1.2 网络拓扑 ................................................................................................................................... 10 3.1.3 配置流程 ................................................................................................................................... 10 3.1.4 配置步骤 ................................................................................................................................... 10 3.2 三层转发简介 ....................................................................................................................................... 11 3.2.1 配置需求 .................................................................................................................................... 11 3.2.2 网络拓扑 .................................................................................................................................... 11 3.2.3 配置流程 .................................................................................................................................... 11 3.2.4 配置步骤 ................................................................................................................................... 12
s2000-hi操作手册(V1.02)22-NTP操作

NTP 目录目录第1章 NTP.............................................................................................................................1-11.1 NTP简介............................................................................................................................1-11.1.1 NTP的应用..............................................................................................................1-11.1.2 NTP工作原理..........................................................................................................1-21.1.3 NTP的工作模式......................................................................................................1-31.2 配置NTP工作模式............................................................................................................1-51.2.1 配置准备..................................................................................................................1-51.2.2 配置过程..................................................................................................................1-61.3 配置访问控制权限..............................................................................................................1-71.4 配置NTP验证功能............................................................................................................1-71.4.1 配置准备..................................................................................................................1-71.4.2 配置过程..................................................................................................................1-81.5 配置NTP可选参数............................................................................................................1-91.6 NTP配置显示...................................................................................................................1-101.7 NTP典型配置举例...........................................................................................................1-111.7.1 配置NTP服务器模式............................................................................................1-111.7.2 配置NTP对等体模式............................................................................................1-121.7.3 配置NTP广播模式................................................................................................1-141.7.4 配置NTP组播模式................................................................................................1-161.7.5 配置带身份验证的NTP服务器模式......................................................................1-18第1章 NTP1.1 NTP简介NTP(Network Time Protocol,网络时间协议)是由RFC1305定义的时间同步协议,用来在分布式时间服务器和客户端之间进行时间同步。
RG-S2300 Series Installation Manual

Installation ManualRG-S2300 Series Secure Access SwitchCopyright StatementRuijie Networks Co., Ltd ©2009All rights reserved.Without our written permission, this document may not be excerpted, reproduced, transmitted, or otherwise in all or in part by any party in any means., , ,, , , ,are all registered trademarks of Ruijie Networks Co., Ltd and are protected by law.DisclaimerThe information contained in this manual may be modified without notification. Ruijie Networks has tried its best to maintain the accuracy and reliability of this manual on the website.Ruijie Networks takes no responsibility for the miss, inaccuracy or error and the resulting damage and loss in this manual.ContentsPREFACE (5)1PRODUCT OVERVIEW (7)1.1P RODUCT O VERVIEW (7)1.2M AIN T ECHNICAL C HARACTERISTICS OF RG-S2300 (7)1.3RG-S2300S ERIES S WITCHES (8)1.3.1RG-S2328G Ethernet Switch (8)1.3.2RG-S2352G Ethernet Switch (11)1.4LED I NDICATORS (14)1.5E XTENSION M ODULES (16)1.5.1M2000-02SFP/GT Module (16)1.5.2M3250-STACK Module (17)2PREPARATION BEFORE INSTALLATION (19)2.1S AFETY S UGGESTIONS (19)2.1.1Safety Precautions for Installing the System (19)2.1.2Movement Safety (19)2.1.3Electric Safety (19)2.1.4Static Discharge Damage Prevention (20)2.1.5Laser Safety (20)2.2I NSTALLATION S ITE R EQUIREMENTS (20)2.2.1Ventilation Requirements (20)2.2.2Temperature and Humidity Requirements (20)2.2.3Cleanness Requirements (21)2.2.4EMI (22)2.3S YSTEM G ROUNDING R EQUIREMENTS (22)2.3.1Safety Grounding (23)2.3.2Lightning Grounding (23)2.3.3EMC Grounding (23)2.4L IGHTNING R ESISTANCE C ONSIDERATIONS (23)2.5EMI C ONSIDERATION (24)2.6P RECAUTION FOR F IBER C ONNECTIONS (24)2.7R EQUIREMENTS OF I NSTALLATION T OOLS (24)3PRODUCT INSTALLATION (26)3.1I NSTALLATION P ROCEDURE (26)3.2C ONFIRMATIONS B EFORE I NSTALLATION (26)3.3I NSTALLING THE S2300S ERIES (27)3.3.1Precautions (27)3.3.2Mounting the Switch to a Standard 19-inch Rack (27)3.3.3Mounting the Switch to the Wall (27)3.3.4Mounting the Switch to the Desktop (28)3.4C HECKING A FTER I NSTALLATION (28)4SYSTEM DEBUGGING (29)4.1C ONFIGURATION E NVIRONMENT E STABLISHMENT (29)4.1.1Establishing the Configuration Environment (29)4.1.2Connecting the Console Cable (29)4.1.3Setting Terminal Parameters (29)4.2P OWER-ON S TARTUP (30)4.2.1Checking Before Power-on (30)4.2.2Checking After Power-on (Recommended) (30)5MAINTENANCE AND TROUBLESHOOTING (31)5.1G ENERAL T ROUBLESHOOTING P ROCEDURE (31)5.2T ROUBLESHOOTING C OMMON F AULTS (31)APPENDIX A: CONNECTORS AND CONNECTION MEDIA (33)1000BASE-T/100BASE-TX/10BASE-T P ORTS (33)O PTICAL F IBER C ONNECTION (34)APPENDIX B MINI-GBIC MODULES (35)M ODELS AND T ECHNICAL S PECIFICATIONS OF THE M INI-GBIC(SFP)M ODULE (35)PrefaceThank you for using our switches. This guide (version: V1.02) provides you with detailed operation guide that allows you to easily install and use the switches.ScopeThis manual describes the functional and physical features of the switches, and provides the installation procedures, troubleshooting procedures, technical specifications, and specifications and use rules of cables and connectors. It is intended for the users that have some experience in installing and maintaining network hardware and want to learn the above information. At the same time, it is assumed that the users of this switch are already familiar with the related terms and concepts of Ethernet.Document Structure✧Chapter 1 "Product Overview" describes the main characteristics and typical applications ofthis product.✧Chapter 2 "Preparation before Installation" lists the safety, power supply, and siterequirements that must be met before the switch can be installed.✧Chapter 3 “Product Installation” describes how to install the integrated switch and modulesand connect its power cables and grounding lines.✧Chapter 4 "System Debugging" describes the debugging after the switch is powered on forthe first time.✧Chapter 5 "Maintenance and Troubleshooting” describes how to monitor and maintain theswitch in use.✧Chapter 6 "Troubleshooting" describes possible problems, detections and solutions in thehardware installation and application.✧Appendix A “Connector and Connection Media”✧Appendix B “Mini-GBIC Modules”Related DocumentsSwitch Software Manual——covering CLI commands, software configuration guide, and version release notes.Obtaining DocumentationYou can obtain the documentation you need through the following channels:Internet:You can obtain the latest on-line documentation of Ruijie Networks at:Documentation CD-ROM:The documentation of Ruijie Networks switches is stored in the CD-ROM package, which is provided to you together with the product you purchase. The CD-ROM is updated frequently, and may be more current than the printed documents.Obtaining Technical AssistanceRuijie Networks provides excellent technical support services for all our products. You can obtain the technical assistance you need through any of the following channels:✧ Ruijie Networks website, from which you can obtain the latest product documentation,causes and problems analysis of product faults, application solutions, and software upgrade.✧ Customer service center of Ruijie Networks, which can provide all customers with neededtechnical assistance for: products, technologies and solutions. The customer service center provides responsive technical support for your product installation problems, software configuration problems, and other network performance problems. ✧ Customer services hotline: 4008-111-000✧ Customer services website: ✧ Customer services email: service@Documentation ConventionsThe symbols used in this document are described as below:NoteThis symbol means the supplement or additional information that you may needto know.CautionThis symbol alerts you to the cautions to avoid data loss or switch damage.1 Product Overview1.1Product OverviewThe RG-S2300 series secure access switches are mostly applied at the access layers of small-and-medium-sized networks to provide line-speed exchanging and complete QoS services andensure the undelayed transmission of key data by applying different traffic classification rules todifferent services. The S2300 series provide flexible medium interfaces and can meet theconnection requirements of different media in network constructions.Table 1-1 RG-S2300 seriesModel 10/100Base-Tadaptive Ethernet port 10/100/1000Base-Tadaptive Ethernet port1000Base-X SFP port Console portS2328G 24 2 2 1S2352G 48 2 2 1The 1000Base-X SFP port and a corresponding 10/100/1000Base-T adaptive Ethernet port forma fiber/copper combo port. That is, only one port in the fiber/copper combo port is available at aparticular time.Table 1-2 shows the mappings between two ports that form a fiber/copper comboport.Table 1-2 Mappings between two ports that form a fiber/copper combo portModel 1000Base-X SFP port 10/100/1000Base-T adaptive EthernetportS2328G 25F 25G26F 26GS2352G 49F 49G50F 50G1.2Main Technical Characteristics of RG-S2300Table 1-3 Technical specifications of the S2300 seriesModel S2328GS2352GModule type Mini-GBIC-SX: single-port 1000BASE-SX mini GBIC conversion module (LC port)Mini-GBIC-LX: single-port 1000BASE-LX mini GBIC conversion module (LC port)Mini-GBIC-ZX50: single-port 1000BASE-ZX mini GBIC conversion module (LC interface), 50 kmMini-GBIC-ZX80: single-port 1000BASE-ZX mini GBIC conversion module (LC port), 80 km M2000-02SFP/GT M3250-STACKPower supply AC input:Rated voltage range: 100- 240V AC Maximum voltage range: 90-264V AC Frequency: 50 / 60 Hz Rated current: 0.6 APower consumptionS2328G: with extension modules < 22 W and without extension modules < 18 WS2352G: with extension modules < 31 W and without extension modules < 27 WTemperature Working temperature: 0ºC to 50ºC Storage temperature: -40ºC to 70ºC Humidity Working humidity: 10% to 90% RH Storage humidity: 5% to 90% RH EMC GB9254-1998 and FCC Class A Security complianceGB4943-2001Dimensions (W x D x H) 440 x 300 x 44 mm WeightWith extension modules 3.9 kg and without extension modules 3.5 kg1.3 RG-S2300 Series Switches1.3.1 RG-S2328G Ethernet Switch1.3.1.1 Product AppearanceThe front panel of the RG-S2328G Ethernet switch provides twenty-four 10/100Base-T Ethernet ports, two GE SFP fiber/copper combo ports and one Console port. The backplanel provides the AC power input ports and an extension module slot. Figure 1-1 shows the appearance of the RG-S2328G.Figure 1-1 Appearance of the RG-S2328G1.3.1.2 Ports on the Front PanelFigure 1-2 Schematic diagram of the RG-S2328G front panel - 11. Power system indicator2. Extension module indicator3. Extended port 1 status indicator4. Extended port 2 status indicator5. Console portFigure 1-3Schematic diagram of the RG-S2328G front panel - 26. 10/100Base-T adaptive Ethernet port7. 10/100/1000Base-T adaptive Ethernet port8. 1000Base-X SFP port9. 10/100Base-T adaptive Ethernet port indicator10. 10/100Base-T adaptive Ethernet port indicator11. 1000Base-X SFP port indicator1.3.1.3 Ports on the Back PanelFigure 1-4 Schematic diagram of the RG-S2328G back panel - 11. Extended port2. Label attachmentFigure 1-5 Schematic diagram of the RG-S2328 back panel -23. 3-core AC power interface4. Grounding pole1.3.1.4 Power Supply SystemThe RG-S2328G adopts the AC power input.AC input:Rated voltage range: 100-240V ACMaximum voltage range: 90-264V ACFrequency: 50 / 60 HzRated current: 0.6 A1.3.1.5 Heat Dissipation SystemThe RG-S2328G is designed with no fans. To ensure good dissipation, a ventilation openingspace should be reserved to avoid blocking the air inlet of the cabinet; otherwise, the dissipationmight be affected.1.3.2 RG-S2352G Ethernet Switch1.3.2.1 Product AppearanceThe front panel of the RG-S2352G Ethernet switch provides fourty-eight 10/100Base-T Ethernetports, two GE SFP fiber/copper combo ports and one Console port. The backpanel provides theAC power input ports and an extension module slot. Figure 1-6 shows the appearance of theRG-S2352G.Figure 1-6Appearance of RG-S2352G1.3.2.2 Ports on the Front PanelFigure 1-7 Schematic diagram of the RG-S2352G front panel - 11. Power system indicator2. Extension module indicator3. Extended port 1 status indicator4. Extended port 2 status indicator5. 10/100Base-T adaptive Ethernet port6. Console port7. 10/100Base-T adaptive Ethernet port indicatorFigure 1-8 Schematic diagram of the RG-S2352G front panel - 28. 10/100/1000Base-T adaptive Ethernet port9. 1000Base-X SFP port10. 10/100Base-T adaptive Ethernet port indicator11. 1000Base-X SFP port indicator1.3.2.3 Ports on the Back PanelFigure 1-9 Schematic diagram of the RG-S2352G back panel - 11. Extended portFigure 1-10 Schematic diagram of the RG-S2352G back panel -22. 3-core AC power interface3. Grounding pole1.3.2.4 Power Supply SystemThe RG-S2352G adopts the AC power input. AC input:Rated voltage range: 100-240V AC Maximum voltage range: 90-264V AC Frequency: 50 / 60 Hz Rated current: 0.6 A1.3.2.5 Heat Dissipation SystemThe RG-S2352G is designed with no fans. To ensure good dissipation, a ventilation opening space should be reserved to avoid blocking the air inlet of the cabinet; otherwise, the dissipation might be affected.1.4 LED IndicatorsTable 1-4 LED indicators for the RG-S2328GIndicatorPanel Identification Status MeaningLink indicator StatusOff The switch is not powered on. Solid green The switch is powered on.Extension module indicatorModuleOffThere is no extension module or the extension module is not correctly installed.Solid green The extension module is correctlyinstalled.Extension module port indicator (extended port 1)Link/ACT1OffThe port is down.Solid green The port is up. Flashing greenData are being transceived at the port.Extension module port indicator (extended port 2)Link/ACT2Off The port is down.Solid green The port is up. Flashing green Data are being transceived at the port.10/100Mbps RJ-45 port indicator1 to 24Off The port is down.Solid green The port is up. Flashinggreen Data are being transceived at the port at a rate of 100Mbps. Solid yellow The port is up.Flashing yellowData are being transceived at the port at a rate of 10Mbps. 1000Mbps SFP port indicator25F, 26FOff The port is down.Solid green The port is up.Flashing green Data are being transceived at the port.1000Mbps RJ-45 port indicator25C, 26COffThe port is down.Solid green The port is up.Flashing greenData are being transceived at the port.Table 1-5 LED indicators for the RG-S2352GIndicatorPanel Identification Status MeaningLink indicator StatusOff The switch is not powered on. Solid green The switch is powered on.Extension module indicatorModuleOffThere is no extension module or the extension module is not correctly installed.Solid green The extension module is correctlyinstalled.Extension module port indicator (extended port 1)Link/ACT1OffThe port is down.Solid green The port is up. Flashing green Data are being transceived at the port.Extension module port indicator (extended port 2)Link/ACT2OffThe port is down.Solid green The port is up. Flashing green Data are being transceived at the port.10/100Mbps RJ-45 port indicator1 to 48Off The port is down.Solid green The port is up.Flashing green Data are being transceived at the port at a rate of 100Mbps. Solid yellowThe port is up.Flashing yellowData are being transceived at the port at a rate of 10Mbps. 1000Mbps SFP port indicator49F, 50FOff The port is down.Solid green The port is up.Flashing greenData are being transceived at the port.1000Mbps RJ-45 port indicator49C, 50COff The port is down.Solid green The port is up.Flashing greenData are being transceived at the port.1.5 Extension ModulesThe RG-S2300 series contain the following extension modules: M2000-02SFP/GT and M3250-STACK.1.5.1 M2000-02SFP/GT Module1.5.1.1 Module OverviewFigure 1-12 shows the M2000-02SFP/GT module that is used to extend the two fiber/copper combo ports. Note that the module does not support hot swapping.Figure 1-12 Appearance of the M2000-02SFP/GT module1. 10/100/1000Base-T adaptive Ethernet port2. 10/100Base-T adaptive Ethernet port indicator3. 1000Base-X SFP port indicator4. 1000Base-X SFP port indicator1.5.1.2 Module IndicatorsFigure 1-6 LED indicators for the M2000-02SFP/GTIndicatorPanel Identification Status MeaningPower indicatorPowerOffThe switch is not powered on.Solid greenThe module is already powered on.SFP port indicatorP1/P2OffThe link that connects to the port is not established.Solid green The link that the port connects to is Up. Flashing greenDataarebeingtransceived at the port. CT port indicatorP1/P2OffThe link that connects to the port is not established.Solid green The link that the port connects to is Up. Flashing greenDataarebeingtransceived at the port.1.5.1.3 Technical SpecificationsTable 1-7 Technical specifications of the M2000-02SFP/GT 1.5.2 M3250-STACK Module1.5.2.1 Module OverviewFigure 1-13 shows the M3250-STACK module that is used for the stacking of the S2300 series. The bandwidth of the stack port is 1G.Figure 1-13 Appearance of the M3250-STACK moduleModel M2000-02SFP/GTHot swapping Not supported Power consumption < 4 WTemperature Working temperature: 0ºC to 45ºC Storage temperature: -40ºC to 70ºC Humidity Working humidity: 10% to 90% RH Storage humidity: 5% to 90% RH Weight Net weight about 0.4 kg Dimensions100 x 110 (mm)1. Stack module power indicator2. Stack port3. Stack port indicator1.5.2.2 Module IndicatorsFigure 1-8M3250-STACK IndicatorsIndicator Panel Identification Status Meaning Power indicator Power Off The switch is notpowered on.Solid green The module is alreadypowered on.Stack port indicator STACK-P1/P2 Off The link that connectsto the stack port is notestablished.Solid green The link that connectsto the stack port is Up.Flashing green Data are beingtransceived at thestack port.1.5.2.3 Technical SpecificationsTable 1-9 Technical specifications of the M3250-STACKModel M3250-STACKHot swapping Not supportedTemperature Working temperature: 0ºC to 45ºCStorage temperature: -40ºC to 70ºCHumidity Working humidity: 10% to 90% RHStorage humidity: 5% to 90% RHWeight Net weight about 0.2 kgDimensions 100 x 110 (mm)2 Preparation Before Installation2.1Safety SuggestionsTo avoid personal injury and equipment damage, please carefully read the safety suggestionsbefore you install the RG-S2300 series.The following safety suggestions do not cover all possible dangers.Note2.1.1 Safety Precautions for Installing the System✧Keep the chassis clean, free from any dust.✧Do not place the switch in a walking area.✧Do not wear loose clothes or any other things that may be caught by the chassis duringinstallation and maintenance.✧Turn off all power supplies and remove the power sockets and cables before dismantlingthe cabinet.2.1.2 Movement Safety✧Do not frequently move the switch.✧When moving the switch, note the balance and avoid hurting legs and feet or straining theback.✧Before moving the switch, turn off all power supplies and dismantle all power modules.2.1.3 Electric Safety✧Observe local regulations and specifications when performing electric operations. Relevantoperators must be qualified.✧Carefully check any potential danger in the working area, such as ungrounded powersupply, unreliable grounding of the power supply, and damp/wet ground or floor.✧Find out the location of the emergency power supply switch in the room before installation.First cut off the power supply in the case of an accident.✧Try to avoid maintaining the switch that is powered-on alone.✧Be sure to make a careful check before you shut down the power supply.✧Do not place the equipment in a damp location. Do not let any liquid enter the chassis.Caution 1. Any nonstandard and inaccurate electric operation may cause an accident such as fire or electrical shock, thus causing severe even fatal damages to human bodies and the switch.2. Direct or indirect touch through a wet object on high-voltage and mains supply can bring a fatal danger.2.1.4 Static Discharge Damage PreventionTo prevent damage from static electricity, pay attention to the following:(1) Proper grounding of the switch and floor(2) Indoor dust prevention(3) Proper humidity conditions2.1.5 Laser SafetyAmong the modules supported by the RG-S2300 series, a great number of optical modules are Class I laser products. Therefore, pay attention to the following when you use them:✧When a fiber transceiver works, ensure that the port has been connected with an opticalfiber or is covered with a dust cap, to keep out dust and avoid burning your eyes.✧Do not stare into any optical port.Caution Do not stare into any optical port under any circumstances, as this may cause permanent damage to your eyes.2.2Installation Site RequirementsThe RG-S2300 series must be used indoors. To ensure the normal working and a prolongeddurable life of the switch, the installation site must meet the following requirements.2.2.1 Ventilation RequirementsFor the RG-S2300 series, you must ensure that sufficient space is reserved at the ventilationopenings to ensure the normal ventilation. After various cables have been connected, theyshould be arranged into bundles or placed on the cabling rack, to avoid blocking the air inlets.2.2.2 Temperature and Humidity RequirementsTo ensure the normal operation and prolong the service life of RG-S2300 series, you shouldkeep proper temperature and humidity in the equipment room.If the equipment room has temperature and humidity that do not meet the requirements for along time, the switch may be damaged.✧ In an environment with high relative humidity, the insulating material may have badinsulation or even leak electricity. Sometimes the materials may suffer from mechanicalperformance change and metallic parts may get rusted.✧ In an environment with low relative humidity, however, the insulating strip may dry andshrink. Static electricity may occur easily and endanger the circuit on the switch.✧ In an environment with high temperature, the equipment is subjected to even greater harm,as its performance may degrade significantly and its useful life may be shortened in thecase of long-term exposure that expedites the aging process.Therefore, the ambient temperature and humidity of the RG-S2300 series must meet the requirements listed in 0:Table 2-1 Temperature and humidity requirements of the RG-S2300 series TemperatureRelative Humidity Long-termcondition Short-term condition Long-term condition Short-term condition15ºC-40ºC 0ºC-45ºC 40%-65% 10%-90%Note 1. The ambient temperature and humidity are measured at the point that is 1.5 mabove the floor and 0.4 m before the switch when there is no protective plate infront or back of the switch rack.2. The short-term working condition applies where the continuous working perioddoes not exceed 48 hours and the accumulative total period within a year doesnot exceed 15 days.2.2.3 Cleanness RequirementsDust poses the top threat to the switch running. The indoor dust falling on the switch may beadhered by the static electricity, causing bad contact of the metallic joint. Such electrostatic adherence may occur more easily when the relative humidity is low, not only affecting the switch service life, but also causing communication faults. 错误!未找到引用源。
以太网交换机使用方法

以太网交换机使用说明书目 录物品清单物品清单··················································4 第一章用户手册简介用户手册简介·····································5 1.1 用途·····················································5 1.2 约定·····················································5 1.3用户手册概述 (5)第二章产品概述产品概述·········································6 2.1产品简介·················································6 2.2 产品特性·················································6 2.2.1 主要特性·················································6 2.2.2规格说明 (7)第三章安装指南安装指南·········································8 3.1安装·····················································8 3.1.1 安装在桌面上的方法·······································8 3.1.2 安装在机架上的方法·······································8 3.1.3 加电·····················································8 3.2 交换机的外观·············································8 3.2.1 前面板···················································8 3.2.2 后面板··················································10 3.3注意事项 (10)第四章交换机基本概念交换机基本概念 (12)4.1系统配置················································12 4.1.1 系统信息················································12 4.1.2 IP 地址参数··············································12 4.1.3 文件传输················································12 4.1.4 保存与复位··············································13 4.2 端口管理················································13 4.2.1 端口参数················································13 4.2.2 端口监控················································14 4.2.3 端口描述················································14 4.2.4 端口统计与端口状态······································14 4.2.5 端口带宽················································15 4.2.6 端口广播风暴············································15 4.3 网络配置················································15 4.3.1 最大老化时间与动态地址表································15 4.3.2 静态地址表··············································16 4.3.3 静态安全地址表··········································16 4.3.4Ping 检测 (16)4.4 虚拟局域网管理 (16)4.4.1 VLAN模式配置 (17)4.4.2 Global VID配置 (18)4.4.3 VLAN配置 (18)4.4.4 MTU VLAN组 (19)4.5 Trunk配置 (19)4.6 优先级管理 (20)4.6.1 优先级配置 (20)4.6.2 端口优先级表 (20)4.6.3 TOS优先级 (20)4.6.4 802.1p优先级 (20)4.6.5 802.1p优先级映射表 (21)第五章WEB管理 (22)管理·5.1 概述 (22)5.2 WEB管理的连接 (22)5.2.1 准备工作 (22)5.2.2 连接 (25)5.3 WEB管理界面及操作方法 (26)5.3.1 系统配置 (27)5.3.2 端口管理 (30)5.3.3 网络配置 (37)5.3.4 VLAN管理 (41)5.3.5 Trunk配置 (45)5.3.6 优先级管理 (46) (52)第六章带外管理带外管理·6.1 概述 (52)6.2 带外(out-of-out)的连接方法 (52)6.3 带外管理的界面及操作方法 (53)6.4 CLI命令使用说明 (53)6.4.1 语法帮助 (53)6.4.2 命令帮助使用说明 (53)6.4.3 常用命令 (54)第七章Telnet 管理 (58)管理·7.1 概述 (58)7.2 Telnet的连接方法 (58)7.3 连接 (60) (62)连接器引脚详细说明·插座//连接器引脚详细说明A RJ--45插座附录A RJ物品清单小心打开包装盒,检查包装盒里应有的配件:一台交换机一根交流电源线一根串口线一本用户手册两个L型支架(KN-S1008M+除外)如果发现包装盒内产品有所损坏或者任何配件短缺的情况,请及时和当地经销商联系。
DPtech LSW SI系列以太网交换机典型配置手册v

DPtech LSW3600-SI系列以太网交换机典型配置手册手册版本:v1.4软件版本:LSW3600-S221S002D013DPtech LSW3600-SI系列以太网交换机典型配置手册v1.4.docx声明Copyright © 2008-2016杭州迪普科技有限公司版权所有,保留一切权利。
非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本书内容的部分或全部,并不得以任何形式传播。
为杭州迪普科技有限公司的商标。
对于本手册中出现的其他所有商标或注册商标,由各自的所有人拥有。
由于产品版本升级或其他原因,本手册内容有可能变更。
杭州迪普科技有限公司保留在没有任何通知或者提示的情况下对本手册的内容进行修改的权利。
本手册仅作为使用指导,杭州迪普科技有限公司尽全力在本手册中提供准确的信息,但是杭州迪普科技有限公司并不确保手册内容完全没有错误,本手册中的所有陈述、信息和建议也不构成任何明示或暗示的担保杭州迪普科技有限公司地址:杭州市滨江区通和路68号中财大厦6层邮编:310051网址:邮箱:support@7x24小时技术服务热线:400-6100-59约定图形界面格式约定各类标志约定表示操作中必须注意的信息,如果忽视这类信息,可能导致数据丢失、功能失效、设备损坏或不可预知的结果。
表示对操作内容的描述进行强调和补充。
目录1典型配置案例支持的设备型号 (1)2常用维护命令行介绍 (1)2.1登陆设备 (1)2.1.1 SSH方式登陆 (1)2.1.2 Telnet方式登陆 (1)2.2查看设备信息 (2)2.3软件版本升级 (2)2.3.1 Conboot模式下操作 (2)2.3.2命令行下操作 (9)2.4清除配置 (9)3基本二三层转发配置案例 (9)3.1二层转发简介 (9)3.1.1配置需求 (10)3.1.2网络拓扑 (10)3.1.3配置流程 (10)3.1.4配置步骤 (10)3.2三层转发简介 (11)3.2.1配置需求 (11)3.2.2网络拓扑 (11)3.2.3配置流程 (11)3.2.4配置步骤 (12)4端口聚合典型配置案例 (13)4.1端口聚合简介 (13)4.1.1基本概念 (13)4.1.2聚合模式 (14)4.1.3负载分担类型 (14)4.2端口聚合配置案例 (14)4.2.1配置需求 (14)4.2.2网络拓扑 (15)4.2.3配置流程 (15)4.2.4配置步骤 (15)5端口镜像典型配置案例 (17)5.1端口镜像简介 (17)5.1.1端口镜像基本概念 (17)5.1.2端口镜像分类 (18)5.2本地端口镜像配置案例 (18)5.2.1配置需求 (18)5.2.2网络拓扑 (19)5.2.3配置流程 (19)5.2.4配置步骤 (19)5.3远程端口镜像配置案例 (21)5.3.1配置需求 (21)5.3.2网络拓扑 (21)5.3.3配置流程 (21)5.3.4配置步骤 (22)6端口限速典型配置案例 (23)6.1端口限速简介 (23)6.2配置案例 (23)6.2.1配置需求 (23)6.2.2网络拓扑 (24)6.2.3配置流程 (24)6.2.4配置步骤 (24)7端口隔离典型配置案例 (25)7.1端口隔离简介 (25)7.2配置案例 (25)7.2.1配置需求 (25)7.2.2网络拓扑 (26)7.2.3配置流程 (26)7.2.4配置步骤 (26)8 ARP防护典型配置案例 (27)8.1 ARP防护简介 (27)8.1.1 ARP报文有效性检查 (27)8.1.2 ARP用户合法性检查 (27)8.1.3 ARP网关保护 (28)8.2 ARP报文一致性检测配置案例 (28)8.2.1配置需求 (28)8.2.2网络拓扑 (29)8.2.3配置流程 (29)8.2.4配置步骤 (29)8.3 ARP用户合法性配置案例 (30)8.3.1配置需求 (30)8.3.2网络拓扑 (30)8.3.3配置流程 (30)8.3.4配置步骤 (31)8.4 ARP网关保护配置案例 (32)8.4.1配置需求 (32)8.4.2网络拓扑 (32)8.4.3配置流程 (32)8.4.4配置步骤 (33)9路由协议典型配置案例 (34)9.1路由协议简介 (34)9.1.1静态路由协议简介 (34)9.1.2 RIP路由协议简介 (34)9.1.3 OSPF路由协议简介 (34)9.2静态路由配置案例 (35)9.2.1配置需求 (35)9.2.2网络拓扑 (35)9.2.3配置流程 (35)9.2.4配置步骤 (35)9.3 RIP路由配置案例 (37)9.3.1配置需求 (37)9.3.2网络拓扑 (38)9.3.3配置流程 (38)9.3.4配置步骤 (38)9.4 OSPF典型配置案例 (41)9.4.1配置需求 (41)9.4.2网络拓扑 (42)9.4.3配置流程 (42)9.4.4配置步骤 (42)10 DHCP典型配置案例 (45)10.1 DHCP简介 (45)10.2 DHCP Server配置案例 (46)10.2.1配置需求 (46)10.2.2网络拓扑 (47)10.2.3配置流程 (47)10.2.4配置步骤 (47)10.3 DHCP Snooping配置案例 (48)10.3.1配置需求 (48)10.3.2网络拓扑 (49)10.3.3配置流程 (49)10.3.4配置步骤 (50)10.4 DHCP 中继配置案例 (51)10.4.1配置需求 (51)10.4.2网络拓扑 (51)10.4.3配置流程 (52)10.4.4配置步骤 (52)11 QoS典型配置案例 (53)11.1 QoS简介 (53)11.2配置案例 (54)11.2.1配置需求 (54)11.2.2网络拓扑 (55)11.2.3配置流程 (55)11.2.4配置步骤 (55)12 802.1x典型配置案例 (56)12.1 802.1x简介 (56)12.1.1基本概念 (56)12.1.2认证方式 (56)12.1.3端口接入控制模式 (57)12.1.4 Radius认证分类 (57)12.2 802.1x本地认证配置案例 (57)12.2.1配置需求 (57)12.2.2网络拓扑 (58)12.2.3配置流程 (58)12.2.4配置步骤 (58)12.3 802.1x Radius认证配置案例 (59)12.3.1配置需求 (59)12.3.2网络拓扑 (59)12.3.3配置流程 (59)12.3.4配置步骤 (59)13生成树典型配置案例 (60)13.1生成树简介 (60)13.2 STP配置案例 (62)13.2.1配置需求 (62)13.2.2网络拓扑 (63)13.2.3配置流程 (63)13.2.4配置步骤 (63)13.3 RSTP配置案例 (65)13.3.1配置需求 (65)13.3.2网络拓扑 (66)13.3.3配置流程 (66)13.3.4配置步骤 (66)13.4 MSTP配置案例 (67)13.4.1配置需求 (67)13.4.2网络拓扑 (68)13.4.3配置流程 (68)13.4.4配置步骤 (69)14 SNMP典型配置 (72)14.1 SNMP简介 (72)14.2 SNMP配置案例 (73)14.2.1配置需求 (73)14.2.2网络拓扑 (73)14.2.3配置流程 (73)14.2.4配置步骤 (74)15 NTP配置案例 (74)15.1 NTP简介 (74)15.2 NTP配置案例 (75)15.2.1配置需求 (75)15.2.2网络拓扑 (75)15.2.3配置流程 (75)15.2.4配置步骤 (75)16日志收集配置案例 (76)16.1日志简介 (76)16.2日志收集案例 (76)16.2.1配置需求 (76)16.2.2网络拓扑 (76)16.2.3配置流程 (77)16.2.4配置步骤 (77)1典型配置案例支持的设备型号LSW3600-SI系列2常用维护命令行介绍2.1登陆设备2.1.1SSH方式登陆在交换机上开启SSH后,就可以在串口终端上输入设备的管理地址、用户名(初始用户名admin)和密码(初始密码admin_default)登录设备。
DPtech LSW3003系列工业以太网交换机典型配置手册v1.3

LSW3003系列工业以太网交换机典型配置手册手册版本:v1.3软件版本:LSW3003-M231S003D006P015DPtech LSW3003系列工业以太网交换机典型配置手册v1.3.docx声明Copyright © 2008-2016杭州迪普科技有限公司版权所有,保留一切权利。
非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本书内容的部分或全部,并不得以任何形式传播。
为杭州迪普科技有限公司的商标。
对于本手册中出现的其他所有商标或注册商标,由各自的所有人拥有。
由于产品版本升级或其他原因,本手册内容有可能变更。
杭州迪普科技有限公司保留在没有任何通知或者提示的情况下对本手册的内容进行修改的权利。
本手册仅作为使用指导,杭州迪普科技有限公司尽全力在本手册中提供准确的信息,但是杭州迪普科技有限公司并不确保手册内容完全没有错误,本手册中的所有陈述、信息和建议也不构成任何明示或暗示的担保杭州迪普科技有限公司地址:杭州市滨江区通和路68号中财大厦6层邮编:310051网址:邮箱:support@7x24小时技术服务热线:400-6100-59约定图形界面格式约定各类标志约定表示操作中必须注意的信息,如果忽视这类信息,可能导致数据丢失、功能失效、设备损坏或不可预知的结果。
表示对操作内容的描述进行强调和补充。
目录1产品概述 (1)1.1 Web管理 (1)1.1.1登陆Web管理界面 (1)1.1.2 Web界面布局介绍 (2)2管理员 (3)2.1管理员简介 (3)2.2管理员配置 (3)3远程管理 (4)3.1 Telnet配置 (4)3.2 SSH配置 (6)4软件版本升级 (8)4.1简介 (8)4.2软件版本升级 (8)5基本二三层转发 (10)5.1 VLAN简介 (10)5.2端口类型 (11)5.3二层转发简介 (11)5.3.1配置需求 (11)5.3.2网络拓扑 (12)5.3.3配置流程 (12)5.3.4配置步骤 (12)5.4配置步骤 (13)5.4.1配置需求 (13)5.4.2网络拓扑 (14)5.4.3配置流程 (14)5.4.4配置步骤 (14)6端口聚合 (17)6.1简介 (17)6.2端口聚合配置案例 (17)6.2.1配置需求 (17)6.2.2网络拓扑 (18)6.2.3配置流程 (18)6.2.4配置步骤 (18)7端口镜像 (20)7.1简介 (20)7.2端口镜像的基本概念 (20)7.3端口镜像配置案例 (21)7.3.1配置需求 (21)7.3.2网络拓扑 (21)7.3.3配置流程 (21)7.3.4配置步骤 (21)8静态路由 (23)8.1简介 (23)8.2静态路由配置案例 (23)8.2.1配置需求 (23)8.2.2网络拓扑 (23)8.2.3配置流程 (23)8.2.4配置步骤 (24)9生成树 (26)9.1生成树简介 (26)9.2 STP配置案例 (27)9.2.1配置需求 (27)9.2.2网络拓扑 (27)9.2.3配置流程 (27)9.2.4配置步骤 (28)9.3 RSTP配置案例 (31)9.3.1配置需求 (31)9.3.2网络拓扑 (32)9.3.3配置流程 (32)9.3.4配置步骤 (32)1产品概述1.1Web管理1.1.1登陆Web管理界面Web管理界面的登陆方法:(1) 确认主机同交换机系统管理口通讯正常。
华为 Quidway S2300 系列以太网交换机 V100R005C00 说明书

Quidway S2300系列以太网交换机V100R005C00产品描述文档版本01发布日期2010-08-15华为技术有限公司版权所有 © 华为技术有限公司 2010。
保留一切权利。
非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部,并不得以任何形式传播。
商标声明和其他华为商标均为华为技术有限公司的商标。
本文档提及的其他所有商标或注册商标,由各自的所有人拥有。
注意您购买的产品、服务或特性等应受华为公司商业合同和条款的约束,本文档中描述的全部或部分产品、服务或特性可能不在您的购买或使用范围之内。
除非合同另有约定,华为公司对本文档内容不做任何明示或默示的声明或保证。
由于产品版本升级或其他原因,本文档内容会不定期进行更新。
除非另有约定,本文档仅作为使用指导,本文档中的所有陈述、信息和建议不构成任何明示或暗示的担保。
华为技术有限公司地址:深圳市龙岗区坂田华为总部办公楼邮编:518129网址:客户服务邮箱:support@客户服务电话:0755-******** 4008302118客户服务传真:0755-********Quidway S2300系列以太网交换机产品描述前言前言读者对象本文档针对S2300设备,介绍了产品定位和特点、产品架构、链路特性、业务特性、应用场景、操作和维护、技术指标。
本文档提供S2300设备的总体情况,便于读者全面了解产品特征。
本文档主要适用于以下工程师:l网络规划工程师l硬件安装工程师l调测工程师l数据配置工程师l现场维护工程师l网络监控工程师l系统维护工程师符号约定在本文中可能出现下列标志,它们所代表的含义如下。
修订记录修改记录累积了每次文档更新的说明。
最新版本的文档包含以前所有文档版本的更新内容。
文档版本 01 (2010-08-15)第一次正式发布。
前 言Quidway S2300系列以太网交换机产品描述Quidway S2300系列以太网交换机产品描述目录目录前言 (iii)1 产品定位和特点............................................................................................................................1-11.1 产品定位.........................................................................................................................................................1-21.2 产品特点.........................................................................................................................................................1-21.2.1 电信级的可维护性................................................................................................................................1-21.2.2 强大的多业务接入能力........................................................................................................................1-21.2.3 灵活的组网能力....................................................................................................................................1-31.2.4 网络级QoS保障...................................................................................................................................1-31.2.5 多层面的扩展能力................................................................................................................................1-31.2.6 周密的安全措施....................................................................................................................................1-31.2.7 便捷的操作维护....................................................................................................................................1-41.2.8 绿色节能设计........................................................................................................................................1-41.2.9 先进的防雷技术....................................................................................................................................1-41.2.10 人性化的PoE供电方式.....................................................................................................................1-42 产品架构........................................................................................................................................2-12.1 概述.................................................................................................................................................................2-22.2 整机结构.........................................................................................................................................................2-22.3 硬件模块.........................................................................................................................................................2-42.3.1 交换主控板............................................................................................................................................2-52.3.2 电源........................................................................................................................................................2-62.3.3 风扇........................................................................................................................................................2-62.4 软件结构.........................................................................................................................................................2-63 链路特性........................................................................................................................................3-13.1 以太网特性.....................................................................................................................................................3-23.1.1 链路聚合................................................................................................................................................3-23.1.2 接口流控................................................................................................................................................3-23.1.3 流量抑制................................................................................................................................................3-23.1.4 VLAN.....................................................................................................................................................3-33.1.5 QinQ.......................................................................................................................................................3-43.1.6 GVRP.....................................................................................................................................................3-43.2 STP/RSTP/MSTP............................................................................................................................................3-43.2.1 STP和RSTP.........................................................................................................................................3-43.2.2 MSTP.....................................................................................................................................................3-43.2.3 MSTP 保护功能....................................................................................................................................3-53.2.4 局部STP 和BPDU 隧道......................................................................................................................3-53.3 SEP..................................................................................................................................................................3-63.4 接口安全保护.................................................................................................................................................3-63.5 链路检测.........................................................................................................................................................3-64 业务特性........................................................................................................................................4-14.1 IPv6.................................................................................................................................................................4-24.2 组播.................................................................................................................................................................4-24.2.1 IGMP Snooping......................................................................................................................................4-24.2.2 组播成员接口快速离开........................................................................................................................4-24.2.3 组播流量控制........................................................................................................................................4-24.2.4 可控组播................................................................................................................................................4-24.3 QoS..................................................................................................................................................................4-34.3.1 流分类....................................................................................................................................................4-34.3.2 访问控制和重标记................................................................................................................................4-34.3.3 流量监管................................................................................................................................................4-34.3.4 拥塞管理................................................................................................................................................4-44.3.5 接口限速................................................................................................................................................4-44.3.6 支持聚合CAR.......................................................................................................................................4-44.4 安全.................................................................................................................................................................4-44.4.1 设备的安全............................................................................................................................................4-54.4.2 业务的安全............................................................................................................................................4-54.4.3 安全认证................................................................................................................................................4-64.5 可靠性.............................................................................................................................................................4-64.6 LLDP...............................................................................................................................................................4-74.7 NQA................................................................................................................................................................4-74.8 集群管理.........................................................................................................................................................4-74.9 堆叠.................................................................................................................................................................4-84.10 Web Server....................................................................................................................................................4-85 特性组网应用................................................................................................................................5-15.1 城域网应用.....................................................................................................................................................5-25.2 VLAN Mapping..............................................................................................................................................5-25.3 IPTV 应用.......................................................................................................................................................5-35.4 端到端QoS.....................................................................................................................................................5-45.5 局部STP 接入汇聚........................................................................................................................................5-55.6 集群管理.........................................................................................................................................................5-66 操作维护和网管系统....................................................................................................................6-16.1 维护和管理.....................................................................................................................................................6-26.1.1 多种配置方式........................................................................................................................................6-26.1.2 监控和维护............................................................................................................................................6-2目 录Quidway S2300系列以太网交换机产品描述Quidway S2300系列以太网交换机产品描述目录6.1.3 诊断和调测............................................................................................................................................6-36.1.4 软件升级和热补丁................................................................................................................................6-46.1.5 硬件异常处理........................................................................................................................................6-46.2 U2000网管.....................................................................................................................................................6-46.2.1 网管组网方式........................................................................................................................................6-46.2.2 U2000网管站........................................................................................................................................6-57 系统技术指标................................................................................................................................7-17.1 物理参数.........................................................................................................................................................7-27.2 光模块属性.....................................................................................................................................................7-37.3 系统配置.........................................................................................................................................................7-57.4 软件特性列表.................................................................................................................................................7-6Quidway S2300系列以太网交换机产品描述插图目录插图目录图2-1 S2309TP-SI/EI产品外观..........................................................................................................................2-2图2-2 S2318TP-SI/EI产品外观..........................................................................................................................2-2图2-3 S2326TP-SI/EI产品外观..........................................................................................................................2-3图2-4 S2352P-EI产品外观.................................................................................................................................2-3图2-5 S2309TP-PWR-EI产品外观.....................................................................................................................2-3图2-6 S2326TP-PWR-EI产品外观.....................................................................................................................2-4图2-7 S2300硬件模块的逻辑结构....................................................................................................................2-5图5-1 S2300在城域网中的应用........................................................................................................................5-2图5-2 S2300提供VLAN Mapping功能............................................................................................................5-3图5-3 S2300在IPTV中的应用.........................................................................................................................5-4图5-4 S2300提供端到端QoS保障...................................................................................................................5-5图5-5 S2300提供局部STP接入汇聚...............................................................................................................5-6图5-6 S2300提供集群管理功能........................................................................................................................5-7Quidway S2300系列以太网交换机产品描述表格目录表格目录表7-1物理参数....................................................................................................................................................7-2表7-2 SFP光模块(FE)的属性..........................................................................................................................7-3表7-3 ESFP光模块(FE)的属性..........................................................................................................................7-3表7-4 ESFP光模块(GE)的属性....................................................................................................................7-4表7-5 ESFP光模块(CWDM彩光)的属性....................................................................................................7-4表7-6系统配置....................................................................................................................................................7-5表7-7功能特性列表............................................................................................................................................7-6Quidway S2300系列以太网交换机产品描述 1 产品定位和特点1产品定位和特点关于本章1.1 产品定位1.2 产品特点1.1 产品定位Quidway S2300系列以太网交换机为A 类产品,在生活环境中,该产品可能会造成无线电干扰。
普联全千兆Web网管交换机安装手册说明书

安装手册全千兆Web网管交换机Enterprise Networking SolutionTL-SG2048TL-SG2226/TL-SG2218TL-SG2024/TL-SG2016TL-SG2024D/TL-SG2016D TL-SG2422F/TL-SG2414F全千兆Web网管PoE交换机TL-SG2226PE/TL-SG2226P TL-SG2218PE/TL-SG2218P TL-SG2024MP声明Copyright © 2020 普联技术有限公司版权所有,保留所有权利未经普联技术有限公司明确书面许可,任何单位或个人不得擅自仿制、复制、誊抄或转译本手册部分或全部内容,且不得以营利为目的进行任何方式(电子、影印、录制等)的传播。
为普联技术有限公司注册商标。
本手册提及的所有商标,由各自所有人拥有。
本手册所提到的产品规格和资讯仅供参考,如有内容更新,恕不另行通知。
除非有特殊约定,本手册仅作为使用指导,所作陈述均不构成任何形式的担保。
I声明相关文档除本安装手册外,我们还提供以下文档的电子版本。
如需获取最新产品资料,请登心,我们将为您提供技术支持服务。
安装手册简介《全千兆Web网管交换机安装手册》主要介绍交换机的硬件特性、安装方法以及在安装过程中应注意事项。
本手册包括以下章节:第1章:产品介绍。
简述交换机的基本功能特性并详细介绍外观信息。
第2章:产品安装。
指导交换机的硬件安装方法以及注意事项。
第3章:硬件连接。
指导交换机与其他设备之间的连接及注意事项。
第4章:登录Web管理界面。
指导通过Web登录配置交换机。
附录A:常见故障处理。
附录B:技术参数规格。
II相关文档附录C:连接SFP端口补充说明。
本手册适合下列人员阅读:网络工程师网络管理员约定在本手册以下部分,如无特别说明,均以TL-SG2226机型为例介绍,所提到的交换机是指全千兆Web网管交换机。
本手册采用了如下几种醒目标志来表示操作过程中应该注意的地方,这些标志的III阅读对象目录第1章 产品介绍 ———————————011.1 产品简介 (01)1.2 产品外观 (02)第2章 产品安装 ———————————092.1 物品清单 (09)2.2 安装注意事项 (09)2.3 安装工具准备 (11)2.4 产品安装 (11)第3章 硬件连接 ———————————133.1 连接至RJ45端口 (13)3.2 连接SFP端口 (13)3.3 连接电源线 (14)3.4 设备初始化 (14)3.5 安装后检查 (14)第4章 登录Web管理界面 ———————15附录A 故障处理 ———————————16附录B 技术参数规格 —————————17附录C 连接SFP端口补充说明 —————18IV目录01全千兆Web网管交换机安装手册产品介绍第1章 产品介绍1.1 产品简介普联技术有限公司全新开发推出的Web网管交换机,采用高性能硬件和软件平台,提供灵活、高性价比的全千兆端口,支持802.1Q VLAN、端口监控、端口汇聚、QoS等常用功能,易于管理维护,适用于校园、酒店及企业园区网络接入应用场景。
Ruijie RG-S2300 系列交换机 说明书

发行说明RG-S2300系列交换机RGOS 10.2(5), Release (67430) 正式版本版权声明福建星网锐捷网络有限公司©2009版权所有,保留一切权利。
没有经过本公司书面许可,任何单位和个人不得擅自摘抄、复制本书内容的部分或者全部,并且不得以任何形式传播。
、、、、、、、都是福建星网锐捷网络有限公司的注册商标,不得仿冒。
前言本文记录了RG-S2300系列交换机RGOS 10.2(5), Release(67430)版本的信息,内容包括:关于本文的任何疑问,请咨询锐捷网络技术支持热线:4008-111-000 。
目录1基本信息 (5)2硬件特性 (5)2.1支持的硬件 (5)2.2硬件限制 (6)3软件特性 (6)3.1解决问题 (6)3.2新增功能 (8)3.3功能变更 (8)3.4软件限制 (8)4配套手册 (10)5升级说明 (11)5.1升级文件清单 (11)5.2升级注意事项 (11)1 基本信息2 硬件特性2.1 支持的硬件2.2 硬件限制无3 软件特性3.1 解决问题该版本解决了以下问题:3.2 新增功能在基线版本的基础上新增以下功能:3.3 功能变更无。
3.4 软件限制本版本中已知的问题以及对应的规避措施其他限制这里主要说明下第2代su下发功能的限制:S23的su分发功能打开后,能够同时解决品控1992与品控2419的哈希冲突问题;这是由于将认证用户从MAC地址表切换为FP表来实现而达到的目的。
但将MAC地址表切换为FP表实现,由于FP表是许多安全功能共用的资源,所以安全功能的使用情况对容量指标会有较大影响。
并且会引入许多的限制。
在部署SU分发功能的时候,请特别注意。
4 配套手册该版本适用的产品用户手册如下:以上产品用户手册可从锐捷网络技术支持网站下载:/。
RG-S2300系列交换机RGOS 10.2(5),Release(67430)正式版本发行说明.doc 5 升级说明5.1 升级文件清单5.2 升级注意事项在对该版本进行升级的过程中,请注意以下事项:在升级或者自动升级过程中,会有不允许重启的提示,一旦出现类似提示,请务必不要断电或者复位系统,也不要随便插拔其他模块。
华为2300系列交换机配置命令

[Quidway]sysname 交换机命名
[Quidway]interface ethernet 0/1 进入接口视图
[Quidway]interface vlan x 进入接口视图
[Quidway-Vlan-interfacex]ip address 10.65.1.1 255.255.0.0
[Quidway]stp root {primary|secondary} 设置交换机为根或根的备份
[Quidway-Ethernet0/1]stp cost 200 设置交换机端口的花费
[SwitchA-vlanx]isolate-user-vlan enable 设置主vlan
[SwitchA]Isolate-user-vlan secondary 设置主vlan包括的子vlan
如果包的vlan id与PVId一致,则去掉vlan信息. 默认PVID=1。
所以设置PVID为所属vlan id, 设置可以互通的vlan为untagged.
端口聚合配置命令
[Quidway]link-aggregation ethernet 0/7 to ethernet 0/10 {ingress|both} 配置端口聚合
[S3026-ui-vty0-4]user privilege level 3
[Quidway-Ethernet0/1]duplex {half|full|auto} 配置端口双工工作状态
[Quidway-Ethernet0/1端口工作速率
[Quidway-Ethernet0/1]flow-control 配置端口流控
德尔PowerConnect2200 2300系列以太网交换机技术规范说明书

w w w.d e l l.c o m | s u p p o r t.d e l l.c o m0K5672A00Dell™ PowerConnect™ 2200/2300 Series Ethernet SwitchesIntroductionThis document describes changes to the technical specifications of the PowerConnect 2200/2300 series Ethernet switches. This information replaces and supercedes that found in the Dell PowerConnect 2216/2224/2324 Switches User’s Guide . Where any differences exist in thespecifications or procedures between the two documents, the information in this document is more accurate.Product Specifications•PowerConnect 2216 –Provides 16 ports supporting 10/100Base-T Ethernet.–All ports support full- or half-duplex mode and PAUSE frames.•PowerConnect 2224–Provides 24 ports supporting 10/100Base-T Ethernet.–All ports support full- or half-duplex mode and PAUSE frames.•PowerConnect 2324–Provides 24 ports supporting 10/100Base-T Ethernet and an additional 2 ports supporting 1000Base-T Ethernet.–The 10/100Base-T ports support full- or half-duplex mode; the 1000Base-T ports support full-duplex mode only.–The 10/100Base-T ports support PAUSE frames; the 1000Base-T ports do not support PAUSE frames.Front-Panel Indicators1000Base-T Ports Link/Activity (SPD/LNK/ACT) LED (PowerConnect 2324 only) •Steady green — A 1000 Mbps link has been established, but no data is being transmitted or received.•Blinking green — A 1000 Mbps link has been established and data is being transmitted or received.•Off — No link has been established.NOTE: No link will will be detected if a 10/100Base-T device is connected to a 1000Base-T port (ports 25 and 26) on the PowerConnect 2324 switch.February 2004w w w .d e l l .c o m | s u p p o r t .d e l l .c o mAdditional Troubleshooting StepThe following information is in addition to that found in Table 2-1 in the Dell PowerConnect 2216/2224/2324 Switches User’s Guide .____________________Information in this document is subject to change without notice.©2004Dell Inc.All rights reserved. Printed in China.Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.Trademarks used in this text: Dell , the DELL logo, and PowerConnect are trademarks of Dell Inc.Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.ProblemProbable CauseCorrective ActionLink LED is not lightedA 10/100Base-T-capable device or 1000Base-T half-duplex device is connected to a 1000Base-T port (ports 25 and 26) on aPowerConnect 2324 switch.Connect only 1000Base-T full-duplex capable devices to ports 25 or 26 on the PowerConnect 2324 switch.。
华为23系列交换机配置

1.5关闭和打开端口
命令 目的
Step1 System-view 进入配置状态
Step2 interface {vlan vlan-id} | {{fastethernet | gigabitethernet} interface-id} | {port-channel port-channel-number} 选择要关闭的端口
4. 键入“display version”参看交换机上IOS版本。
5. 设置2403交换机名称,使用“sysname”命令(也有可能是hostname命令)。
如:Hostname 2403A(此交换机名为2403A)。
6.使用display interface来察看关于全部接口的统计表。
二:交换机端口基本设置
1. 配置端口
1.1 配置端口
命令 目的
Step 1 system-view 进入系统配置状态
Step 2 interface {port-range} 进入端口配置配置状态
Step 3 Quit 退回
Step 4 display interfaces [interface-id] 验证配置
Step 4 display vlan brief 验证
Step 5 save 保存
3将端口分配给一个VLAN
命令 目的
Step 1 System-view 进入配置状态
Step 2 interface interface-id 进入要分配的端口
Step 3 port access vlan vlan-id 把端口分配给某一VLAN
华为交换机quidway S2300配置手册 WORD文档格式下载 /uploads/soft/100729/华为配置手册.doc
华为Quidway S2300系列交换机产品规格说明书

Product SpecificationsS2300-EI S2300-SIItem S2309TP S2309TP-PWRS2318TPS2326TPS2326TP-PWRS2352PS2309TPS2318TPS2326TPForwarding capacity 2.7Mpps2.7Mpps5.4Mpps6.6Mpps6.6Mpps13.2Mpps2.7Mpps5.4Mpps6.6MppsInterface switching capacity 3.6Gbps3.6Gbps7.2Gbps8.8Gbps8.8Gbps17.6Gbps3.6Gbps7.2Gbps8.8GbpsInterface description S2309TP-EI/SI/PWR-EI:eight 10/100Base-TX interfaces, one Combo interface (10/100/1000Base-Tor 100/1000Base-X)S2318TP-EI/SI:sixteen 10/100Base-TX interfaces, two Combo interfaces (10/100/1000Base-T or 100/1000Base-X)S2326TP-EI/SI/PWR-EI:twenty-four 10/100Base-TX interfaces, two Combo interfaces (10/100/1000Base-T or 100/1000Base-X)S2352P-EI:forty-eight 10/100Base-TX interfaces, two 100/1000Base-X SFP interfaces, and two 1000Base-X SFP interfacesSupports the 8K MAC address tableAdds or removes a MAC address entry manuallySets the aging time of MAC addressesSupports the limit to MAC address learning on an interfaceSupports blackhole MAC addresses NAMAC address tableDisables MAC address learning on an interface or in an aggregation group Disables MAC address learning on an interfaceSupports a maximum of 4K VLANs defined in IEEE 802.1Q Supports interface-based VLANsVLAN features Supports MAC address-based VLANsSupports basic QinQSupports 1:1 VLAN switchingSupports N:1 VLAN switchingN/ASupports four queues with different priorities on each interface Supports the algorithms of SP, WRR, and SP+WRRSupports packet queuing based on the 802.1p priority of packetsQoS Supports the interface limit and flow limitSupports traffic classification based on the source MAC address, destination MAC address,source IP address, destination IP address, Layer 4 interface,IP protocol type, VLAN, Ethernet protocol type, and CoS Supports the marking and redirection of packets based on flowsN/AS2300-EI S2300-SIItem S2309TP S2309TP-PWRS2318TPS2326TPS2326TP-PWRS2352PS2309TPS2318TPS2326TPMulticast Supports IGMPv1/v2/v3 snoopingSupports multicast load balancing on trunk interfacesLimits the rate of multicast packets and collects traffic statistics on interfaces Supports IPv6 hostsConfigures static routesIPv6 featuresSupports IPv6 ACLsSupports MLD snoopingNA Supports 1:1 mirroring or N:1 interface mirroringInterfacemirroring Supports flow mirroring N/A Supports IEEE 802.1x and limits the maximum number ofusers on each portSupports dynamic ARP inspectionSupports IP source guardN/ANetwork security Supports AAA authentication such as RADIUS authentication and HWTACACS+ authenticationSupports the binding of the IP address, MAC address, and interfaceSupports the interface limitSupports interface isolation and securitySupports packet filteringSupports MAC address filteringSupports suppression of multicast, broadcast, and unknown unicast packetsLimits the number of learnt MAC addressesSupports CPU protectionLightning protection All service interfaces support 6 KV lightning protection or even 15 KV lightning protection if additional lightning arresters are installedManagement Supports the automatic configuration Configures command lines Supports the configuration of Telnet Supports SNMPv1/v2/v3 Supports RMONSupports HGMPv2Supports SSHv2Support WEB NMSEnvironmentalrequirementsTemperature: 0°C to 50°C Relative humidity: 10% to 90% (non-condensing)Power supply AC:Rated voltage: 100 V to 240 V AC; 50/60 Hz Maximum voltage: 90 V to 264 V AC; 50/60 HzS2300-EIS2300-SI ItemS2309TPS2309TP-PW RS2318TPS2326TPS2326TP-PW RS2352PS2309TPS2318TPS2326TPDC:Rated voltage: –48 V to –60 V DC Maximum voltage: –36 V to –72 V DCN/ADimensions (width x depth x height))S2309TP-EI/SI :250×180×43.6 S2309TP-PWR-EI :320x220x43.6S2318TP-EI/SI,S2326TP-EI/SI :442×220×43.6 S2326TP-PWR-EI :442×420 ×43.6 S2352P-EI :442×220×43.6Weight<1.4kg <2.5kg <2.4kg <2.4kg <4kg (exclusi ve of thepower supply module )<3kg <1.4kg <2.4kg <2.4kgPowerconsumption>7.5W 154W Output PoE power supply: 124W >8.2W >8.6W 160W Output PoEpower supply:124W>20W >7.5W >9W >7.8W。
Quidway S2300系列以太网交换机 配置指南-IP业务(V100R003_02)

配置指南-IP 业务
文档版本 发布日期
02 2009-08-14
华为所有和机密 版权所有 © 华为技术有限公司
华为技术有限公司为客户提供全方位的技术支持,用户可与就近的华为办事处联系,也可直接与公司总部联系。
华为技术有限公司
地址:
深圳市龙岗区坂田华为总部办公楼 邮编:518129
网址:
客户服务电话: 0755-28560000 4008302118
客户服务传真: 0755-28560111
客户服务邮箱: support@
版权所有 © 华为技术有限公司 2009。 保留一切权利。 非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部,并不得以任何形式传播。
1.4 维护.................................................................................................................................................................1-7 1.4.1 监控运行状况.............1-7
商标声明
和其他华为商标均为华为技术有限公司的商标。 本文档提及的其他所有商标或注册商标,由各自的所有人拥有。
注意 由于产品版本升级或其他原因,本文档内容会不定期进行更新。除非另有约定,本文档仅作为使用指导,本文 档中的所有陈述、信息和建议不构成任何明示或暗示的担保。
华为所有和机密 版权所有 © 华为技术有限公司
1.5 配置举例.........................................................................................................................................................1-8 1.5.1 配置 VLANIF 接口的主从 IP 地址示例..............................................................................................1-8
S2300&S3300 V100R006C03 版本说明书

主机软件
无
BootROM 主系 S2300EI-bootrom.bin
无
统软件
Web 网管软件 S2300EI-V100R006C03.001.web.zi 无 p
文档版本 01 (2012-06-30)
华为专有和保密信息
1
1
版权所有 © 华为技术有限公司
目录
目录
1 版本配套说明.................................................................................................................................. 1
1.1 产品版本信息................................................................................................................................................. 1 1.2 软件版本配套说明 ......................................................................................................................................... 1 1.3 单板版本配套说明 ......................................................................................................................................... 3
S2300、S2200系列交换机配置说明

S2300、S2200系列交换机配置说明一、基本配置:Username: admin---------------------用户名adminPassword: *****---------------------密码12345GSQY-WLAN-XYYYT-CXX-POE001#show run -------------查看配置show running-confighostname GSQYA-WLAN-XYYYT-POE001--------------主机名hostname: GSQYA-WLAN-XYYYT-CXX-POE001-----甘肃庆阳-wlan-XY营业厅-POE001GSQY-WLAN-XGYYT-QCX-POE001#config----------------进入配置模式configGSQY-WLAN-XGYYT-QCX-POE001(config)#-------------配置模式二、配置业务数据:2、1创建管理vlan3900(向分公司申请)S2300(config)#interface vlan 3900S2300(config-vlan-3900)#exiS2300(config)#2、2交换机下联口(1-24)fastethernet情况:S2300(config)#interface fastethernet 1/1-----------------------------------进入下联口1口S2300(config-fe1/1)#join vlan 3900 untagged -----------------加入管理Vlan 3900,且untaggedS2300(config-fe1/1)#pvid 3900------------------------------------1口加入pvid 3900S2300(config-fe1/1)#pse enable -----------------------------------打开1口的供电S2300(config-fe1/1)#no shutdown -----------------------------------启用1口S2300(config-fe1/1)#exi------------------------------------------------从1口退出S2300(config)#interface fastethernet 1/2----------------------------------进入下联口2口S2300(config-fe1/2)#join vlan 3900 untagged -----------------加入管理Vlan 3900,且untaggedS2300(config-fe1/2)#pvid 3900 ------------------------------------2口加入pvid 3900S2300(config-fe1/2)#pse enable -----------------------------------打开2口的供电S2300(config-fe1/2)#no shutdown -----------------------------------启用2口S2300(config-fe1/2)#exi-----------------------------------------------从2口退出S2300(config)#==========================以上部分是给1,2口加的数据==========================2300系列交换机有1-24个下联口,每个下联口都重复一遍交换机上联口(25-28)gigaethernet情况:S2300(config)#interface gigaethernet 1/25---------------------------------进入上联口25口S2300(config-ge1/25)#join vlan 3900 tagged----------------加入管理Vlan 3900,且taggedS2300(config-ge1/25)#pvid 3900 -----------------------------------25口加入pvid 3900S2300(config-ge1/25)#no shutdown -----------------------------------启用25口S2300(config-ge1/25)#exi----------------------------------------------从25口退出S2300(config)#==========================以上部分是给25口加的数据==========================2300系列交换机有25-28个上联口,每个上联口都重复一遍三、网管信息:----------所有交换机都一样snmp community GS#POE rw view internetsnmp trap-server 218.203.155.42 162 GS#POE v2snmp trap-server 218.203.165.39 162 GS#POE v2snmp enable四、添加管理地址interface vlAN 3900ip address 172.16.216.180 255.255.252.0quitip route 0.0.0.0 0.0.0.0 172.16.216.1五、常用命令退出:exit或quite或end保存:write file---------y-----------reboot重启erase startup-config---------清除所有数据,重启后生效六、AP运行状态:只有三种方法可以判断:1、AC上看是run还是quite2、查看AP标签上的mac addr 00-26-7a-XX-XX-XX,然后用软件查看是否能收到这个mac地址的信号3、看AP内部指示灯的状态:兰灯常亮就正常;红兰闪烁不正常七、错误判断AP状态的方法:1、交换机上能看到AP的mac地址2、交换机接口灯亮或闪烁3、AP的LAN口灯亮或闪烁八、AP退服的常见原因:1、传输不通,93或交换机vlan没做或做错2、网线不通,网线供电不足,数据传输误码率高3、交换机或AP挂死,需要重启交换机或AP4、换交换机或AP后,交换机没做数据或AC上没替换AP的数据-------------只有当AC上有AP的上报信息时,才能说明AC下联的所有设备正常,且传输链路正常!此时AP才具备上线的必要条件!九、S2200系列交换机的脚本configinterface ethernet 1pse enableQuitinterface ethernet 2pse enablequitinterface ethernet 3pse enablequitinterface vlan 3843member 1-10 untaggedmember 9-10 taggedapply-as-pvid 1-10quitsystemmanagement vlan 3843ip address 172.16.216.41/22gateway 172.16.216.1quitsnmp community GS#POE rwsnmp trap-server 218.203.165.39 GS#POE v2 quit write fileyreboot。
DPtech LSW3600-SI系列以太网交换机安装手册v1.4

DPtech LSW3600-SI系列以太网交换机安装手册杭州迪普科技有限公司为客户提供全方位的技术支持。
通过杭州迪普科技有限公司代理商购买产品的用户,请直接与销售代理商联系;直接向杭州迪普科技有限公司购买产品的用户,可直接与公司联系。
杭州迪普科技有限公司地址:杭州市滨江区通和路68号中财大厦6层邮编:310052声明Copyright 2009杭州迪普科技有限公司版权所有,保留一切权利。
非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本书内容的部分或全部,并不得以任何形式传播。
由于产品版本升级或其他原因,本手册内容有可能变更。
杭州迪普科技有限公司保留在没有任何通知或者提示的情况下对本手册的内容进行修改的权利。
本手册仅作为使用指导,杭州迪普科技有限公司尽全力在本手册中提供准确的信息,但是杭州迪普科技有限公司并不确保手册内容完全没有错误,本手册中的所有陈述、信息和建议也不构成任何明示或暗示的担保目录第1章产品介绍.....................................................................................................................1-11.1产品概述............................................................................................................................1-1 1.2产品型号及规格介绍.........................................................................................................1-1 1.3前后面板介绍....................................................................................................................1-3 1.3.1LSW3600-24T2GC-SI产品外观.....................................................................................1-3 1.3.2LSW3600-48T2GP2GC-SI产品外观...............................................................................1-5 1.3.3LSW3600-24GT4GP-SI产品外观...................................................................................1-7 1.3.4LSW3600-48GT4GP-SI产品外观...................................................................................1-8 1.4端口介绍...........................................................................................................................1-10 1.4.1C ONSOLE口....................................................................................................................1-10 1.4.210/100B ASE-T以太网电接口.........................................................................................1-11 1.4.310/100/1000B ASE-T以太网电接口................................................................................1-11 1.4.4SFP口.............................................................................................................................1-12 1.5产品组件...........................................................................................................................1-15 1.5.1处理器及存储器.............................................................................................................1-15 1.5.2各类接口........................................................................................................................1-15第2章安装前的准备..............................................................................................................2-12.1通用安全注意事项.............................................................................................................2-1 2.2检查安装场所....................................................................................................................2-1 2.2.1温度/湿度要求.................................................................................................................2-1 2.2.2洁净度要求.....................................................................................................................2-2 2.2.3防静电要求.....................................................................................................................2-2 2.2.4抗干扰要求.....................................................................................................................2-3 2.2.5防雷击要求.....................................................................................................................2-3 2.2.6接地要求.........................................................................................................................2-3 2.2.7布线要求.........................................................................................................................2-3 2.3激光使用安全....................................................................................................................2-4 2.4安装工具............................................................................................................................2-43.2安装流程............................................................................................................................3-2 3.3安装设备到指定位置.........................................................................................................3-2 3.3.1安装设备到工作台..........................................................................................................3-3 3.3.2安装设备到19英寸机柜.................................................................................................3-4 3.4连接接地线........................................................................................................................3-5 3.5连接接口线缆....................................................................................................................3-6 3.5.1连接配置口线缆..............................................................................................................3-6 3.5.2连接网络管理口..............................................................................................................3-6 3.5.3连接业务口.....................................................................................................................3-7 3.6连接电源线........................................................................................................................3-7 3.6.1连接交流电源线..............................................................................................................3-7 3.7安装后检查........................................................................................................................3-7第4章设备启动及软件升级..................................................................................................4-14.1设备启动............................................................................................................................4-1 4.1.1搭建配置环境..................................................................................................................4-1 4.1.2设备上电.........................................................................................................................4-4 4.1.3启动过程.........................................................................................................................4-5 4.2W EB默认登录方式............................................................................................................4-6第5章常见问题处理..............................................................................................................5-15.1电源系统问题故障处理.....................................................................................................5-1 5.2设备故障处理....................................................................................................................5-1图形目录图1-1 DPtech LSW3600-24T2GC-SI前视图.....................................................................................1-3 图1-2 DPtech LSW3600-24T2GC-SI前面板指示灯.........................................................................1-4 图1-3 DPtech LSW3600-24T2GC-SI后视图.....................................................................................1-5 图1-4 DPtech LSW3600-48T2GP2GC-SI前视图..............................................................................1-5 图1-5 DPtech LSW3600-48T2GP2GC-SI前面板指示灯..................................................................1-6 图1-6 DPtech LSW3600-48T2GP2GC-SI后视图..............................................................................1-7 图1-7 DPtech LSW3600-24GT4GP-SI前视图...................................................................................1-7 图1-8 DPtech LSW3600-24GT4GP-SI前面板指示灯.......................................................................1-8 图1-9 DPtech LSW3600-24GT4GP-SI后视图...................................................................................1-8 图1-10 DPtech LSW3600-48GT4GP-SI前视图.................................................................................1-9 图1-11 DPtech LSW3600-48GT4GP-SI前面板指示灯...................................................................1-10 图1-12 DPtech LSW3600-48GT4GP-SI后视图...............................................................................1-10 图1-13 RJ45水晶头外观..................................................................................................................1-12 图1-14 以太网电缆的示意图...........................................................................................................1-12 图1-15 LC 型连接器外观.................................................................................................................1-14 图1-16 SC 型连接器外观.................................................................................................................1-14 图1-17 光模块示意图.......................................................................................................................1-14 图1-18 以太网接口(以LSW3600-48GT4GP-SI为例)....................................................................1-16 图3-1 设备安装流程...........................................................................................................................3-2 图3-2 安装设备于工作台...................................................................................................................3-4 图3-3 安装挂耳...................................................................................................................................3-4 图3-4 安装设备到机柜(为清晰起见省略了机柜)........................................................................3-4 图3-5 固定设备...................................................................................................................................3-5 图3-6 连接接地线示意图...................................................................................................................3-5 图3-7 连接保护地线到接地排...........................................................................................................3-6 图3-8 电源线连接示意图...................................................................................................................3-7 图4-1 通过Console口进行本地配置示意图.....................................................................................4-1 图4-2 超级终端连接描述界面...........................................................................................................4-1 图4-3 超级终端连接使用串口设置...................................................................................................4-2 图4-4 串口参数设置...........................................................................................................................4-3 图4-5 超级终端窗口...........................................................................................................................4-3 图4-6 终端类型设置...........................................................................................................................4-4 图4-7 Web网管登录页面...................................................................................................................4-7表格目录表1-1 Console 口属性表...................................................................................................................1-10 表1-2 百兆以太网电接口属性表:....................................................................................................1-11 表1-3 千兆以太网电接口属性表:....................................................................................................1-11 表1-4 千兆以太网光接口属性.........................................................................................................1-12 表2-1 温度/湿度要求..........................................................................................................................2-2 表2-2 灰尘含量要求...........................................................................................................................2-2 表2-3 有害气体限值...........................................................................................................................2-2 表4-1 设置串接口属性.......................................................................................................................4-2第1章产品介绍1.1 产品概述DPtech LSW3600-SI系列以太网交换机(以下简称LSW3600-SI系列)是迪普科技自主开发的下一代安全节能型以太网交换机产品。
Juniper Networks EX2300 以太网交换机产品说明说明书

Data Sheet•1GbE 接入交换机型号包含 USB 小型控制台端口。
•提供带外以太网管理端口。
•已获得减少有害废弃物 (RoHS) 认证。
架构和关键组件EX2300 只占用 1 个机架单元,为空间和电力都十分宝贵的拥挤配线间和接入地点提供了紧凑型的解决方案。
EX2300 交换机的深度为 10 英寸/12 英寸,并且具备低噪音的特点,因而也非常适合部署在开放式办公环境中。
如果您有静音运行的需求,那么可以采用EX2300-C ,这是 EX2300 的紧凑型无风扇版本。
每台 EX2300 交换机均支持四个固定的前面板 1GbE/10GbE 上行链路端口(48 端口多 Gb 型号上有 6 个 1/10GbE 上行链路端口)以及可插拔光纤(单独购买),以用于配线间和上游聚合交换机之间的高速主干连接或链路聚合连接。
1GbE EX2300 接入交换机型号还有一个前面板模式按钮,可提供用于启动设备和选择 LED 模式的简单接口。
后面板的专用 RJ-45 以太网端口可用于带外管理,而通过后面板USB 端口可轻松上传 Junos OS 和配置文件。
Junos Fusion Enterprise 技术瞻博网络 Junos Fusion Enterprise 技术可提供自动化网络配置,并简化大中型企业网络的可扩展性。
将瞻博网络 EX9200 可编程交换机系列用作聚合设备,并将 EX2300 交换机用作卫星节点,可在整栋大楼内(或跨多栋大楼)部署 Junos Fusion Enterprise 技术以连接交换矩阵中的大量交换机,并作为单个设备管理。
图 1:将 EX2300 用作卫星设备的 Junos Fusion Enterprise 部署企业可借助 Junos Fusion 技术通过基于 Junos OS 的瞻博网络路由和交换平台将底层网络元素整合到一个逻辑控制点,从而降低网络复杂性和运营成本。
该技术专为需要在整个企业园区网络中经济高效地部署大量交换机端口并全部通过一个中央设备进行管理的客户而设计。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
DPtech LSW2300系列以太网交换机 安装手册
i
DPtech LSW2300系列以太网交换机安装手册
杭州迪普科技股份有限公司为客户提供全方位的技术支 持。 通过杭州迪普科技股份有限公司代理商购买产品的用 户,请直接与销售代理商联系;直接向杭州迪普科技股 份有限公司购买产品的用户,可直接与公司联系。 杭州迪普科技股份有限公司 地址: 杭州市滨江区通和路68号中财大厦6层 邮编:310052
1.1 产品概述 .................................................................................................................................. 1-1 1.2 产品型号及规格介绍 .............................................................................................................. 1-1 1.3 前后面板介绍 .......................................................................................................................... 1-3 1.3.1 LSW2300-8T4GP-I/LSW2300-8T4GP-I-DC产品外观 ....................................................... 1-3 1.3.2 LSW2300-8GT4GP-I/LSW2300-8GT4GP-I-DC产品外观.................................................. 1-7 1.3.3 LSW2300-16GT2GP-I/ LSW2300-16GT2GP-I-DC 产品外观 .......................................... 1-11 1.4 端口介绍 ................................................................................................................................ 1-14 1.4.1 CONSOLE口 ......................................................................................................................... 1-14 1.4.2 百兆/千兆以太网电接口 .................................................................................................... 1-15 1.4.3 SFP口 .................................................................................................................................. 1-17
iv
DPtech LSW2300系列以太网交换机安装手册
3.3.4 安装设备到19英寸机柜 ....................................................................................................... 3-9 3.4 安装后检查 ............................................................................................................................ 3-10 第4章 设备启动及软件升级 ......................................................................................................... 4-1 4.1 设备启动 .................................................................................................................................. 4-1 4.1.1 搭建配置环境 ....................................................................................................................... 4-1 4.1.2 设备上电 ............................................................................................................................... 4-4 4.1.3 启动过程 ............................................................................................................................... 4-5 4.2 WEB默认登录方式.................................................................................................................. 4-6 第5章 常见问题处理........................................................................................................................ 1 5.1 电源系统问题故障处理 ............................................................................................................. 1 5.2 设备故障处理 ............................................................................................................................. 1
第2章 安装前的准备................................................................................................................... 2-17
2.1 通用安全注意事项 ................................................................................................................ 2-17 2.2 检查安装场所 ........................................................................................................................ 2-17 2.2.1 温度/湿度要求 .................................................................................................................... 2-17 2.2.2 洁净度要求 ......................................................................................................................... 2-18 2.2.3 防静电要求 ......................................................................................................................... 2-19 2.2.4 抗干扰要求 ......................................................................................................................... 2-19 2.2.5 防雷击要求 ......................................................................................................................... 2-19 2.2.6 接地要求 ............................................................................................................................. 2-19 2.2.7 布线要求 ............................................................................................................................. 2-19 2.3 激光使用安全 ........................................................................................................................ 2-20 2.4 安装工具 ................................................................................................................................ 2-20