常用的电解电容尺寸
各种电解电容规格大全(直插)1
5ALUMINUM ELECTROLYTIC CAPACITORS SPECIFICATION FOR APPOV AL 铝 电 解 电 容 器 规 格 承 认 书表1:承认项目 Type DimensionsCustomer客 户Vendor供应商 Heng Xin Da Electronic Co.Ltd恒新达电子有限公司Used Spec通用规格 3300UF/50VProduct Name 品 名Aluminum Electrolytic Capacitor铝电解电容器 Size φD ×L(mm) 外型尺寸18*34 Operating Temperature Rage使用温度-40~+105℃ Rated V oltages Range(V) 额定电压50VCapacitance Tolerance(20℃,120Hz)容量范围±20% 下限: 2640UF 上限: 3960UFβαLead Spacing and Wine Diameter(mm)型状及尺寸d ±0.005ΦD ±β(电容直径)18mm ±0.5 L ±a(电容高度)34mm ±2.0P ±0.5(脚距)10mm ±0.5Φd (引线直径) 0.8 mm ±0.05表2:额定值与特性 TABLE1 RATING&CHARACTERISTIC.1 泄漏电流 I施加额定电压1分钟I=0.01CV 或+3uA 即0.01×容量×电压的读数之内为合格品2损耗角正切〥(120Hz)U R/V 6.3V 10V 16V25V35V50V100V 200V 400V 450Vtgδ0.280.240.200.160.140.120.080.200.250.253 耐久性(105°C)试验时间3000h (施加额定标称纹波电流电压)1:漏电流, 不超过序号1规定值,(施加额定工作电压60秒读数)2:电容量变化率, U R ≤6.3V; ΔC/C ≤+20%~30% 6.3V<U R ≤100V;ΔC/C ≤20% 3:损耗角正切, 不超过序号2规定值1.5倍或0.4取较大者. 4 低温特性测试频率:120Hz额定工作电压(V)6.3 10 16 25 50 200 400 450 阻抗比ZT/Z20max)Z-25℃/Z+20℃ 2 2 2 2 2 2 3 8 Z-40℃/Z+20℃444333495 高温负荷特性在105℃环境中施加额定工作电压1000小时后, 电容器的特性符合右表 的要求.静电容量变化率 初始值的±20%之内 损耗角正切 不大于初始值的200% 漏电流不大于初始值6 高温储存特性在105℃环境中无负荷放置2000小时后,电容器的特性符合序号5中所列规定值. 7耐焊接热特性经过回流焊并冷却至室温后, 电容器的特性符合右表的要求.静电容量变化率 初始值的±10%之内 损耗角正切 不大于初始值 漏电流不大于初始值生产厂商签章:核准: 客户承认签章:核准:CONTENTS 产品系列表Type 类型Series系列Features特性Capacitaner电容量Rated V oltage额定工作电压Operating使用温度Load Life高温负荷V-Chip 贴片型CS Standard size 标准品0.1~1500 4~100 -40~85 1,000 CK Standard size, wide temperature range 宽温标准品0.1~1000 4~50 -40~+105 2,000 CN Non-polarized 无极性品0.1~100 6.3~50 -40~+105 2,000 KP Non-polarized ,wide temperature range宽温无极性0.1~47 6.3~50 -55~+105 2,000 LZ Low impedance 低阻抗品1~220 6.3~35 -55~+105 2,000 KZ Extra lower impedance 极低阻抗品1~1000 6.3~50 -40~+105 2,000 EL Long life impedance 宽温长寿命品0.1~1000 6.3~50 -55~+105 3,000 WL 5000 hours load life 5000小时长寿命品0.1~1000 4~50 -40~+105 5,000 HR High reliability 高可靠品10~330 10~50 -40~+125 1,000General 85℃普通品RA For general purpose Standard size 标准品0.1~22,0006.3~100 -40~85 2,000160~450 -25~85 2,000 RN For general purpose Standard size 7mm标准品0.1~470 6.3~63 -40~85 2,000 RT For general purpose Standard size 5mm标准品0.1~220 4~63 -40~85 2,000General 105℃普通品RK Standard size, wide temperature range 宽温标准品1~33000 6.3`100 -40~+105 2,000160~450 -40~+105 2,000 RM Height 7mm,wide temperature range 7mm宽温标准品0.1~470 4~63 -40~+105 2,000 RS Height 5mm,wide temperature range 5mm宽温标准品0.1~220 4~50 -40~+105 2,000Low Leakage 低漏电品LA Standard size low leakage current低漏电品1~3300 10!63 -40~85 2,000 LK Standard size low leakage current wide宽温低漏电品0.1~330 10!50 -40~+105 2,000 LM Height 7mm low leakage current 7mm低漏电品0.1~100 6.3~63 -40~85 2,000 LS Height 5mm low leakage current 5mm低漏电品0.1~100 4~50 -40~85 2,000Non Polarized 无极性品NP Non-polarized Standard size 无极性品0.47~10000 6.3~250 -40~85 2,000 NK Non-polarized wide temperature range 宽温无极性品0.1~10000 6.3~100 -40~+105 2,000 NM Non-polarized height 7mm 7mm无极性品0.1~47 6.3~50 -40~85 2,000 NS Non-polarized height 5mm 5mm无极性品0.1~47 6.3~50 -40~85 2,000 NA For crossover network non-polarized交流电路无极品1~100 25~200 -40~85 2,000 NE For high output non-polarized 高输出无极性品1~33 50 -40~85 2,000 BP For horiz[ntal defection bi-polarized 双极性品 2.2~22 25~50 -40~85 1,000Lowesr&Loq 高频低阻抗品TM For switching power supplies 高频低阻抗品470~6800 6.3~25 -55~+105 2,000 TN Extremely low impedancer eliabililt高可靠低阻抗品1~15000 6.3~63 -55~105 5,000Sna-in Terminal 焊针品扭角型SM S nap-in terminal stadard series焊针型标准品33~47000 6.3~350 -40~+105 2,000400~450 -25~105SK Snap-in terminal temperature range耐高温焊针品47~47000 10~400 -40~+105 2,000450 -25~105Special Type特别型号RF For photo fiash 闪光灯电路专用品60~180 330 -20~+55 1,000SERIES■表3规格尺寸及最大允许纹波电流DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT电压 v 容量uf6.3V 10V 16V 25V 35V 50V 63V SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C.0.47 5*11 8 5*11 81.0 5*11 13 5*11 132.2 5*11 20 5*11 203.3 5*11 25 5*11 284.7 5*11 25 5*11 28 10 5*11 38 5*7 41 5*7 46 5*11 50 22 5*11 54 5*11 57 5*11 61 5*11 68 6.3*11 82 33 5*11 60 5*11 64 5*11 69 5*11 75 6.3*11 90 8*11 100 47 5*11 71 5*11 80 5*11 106 6.3*11 110 6.3*11 125 8*12 135 100 5*11 95 5*11 100 6.3*7 120 6.3*11 145 8*12 140 8*12 180 8*14 215 220 6.3*7 150 6.3*7 170 6.3*7 195 8*12 225 8*14 250 10*17 345 10*20 390 330 6.3*11 190 8*12 235 8*12 265 8*16 330 10*17 395 10*20 460 12*21 500 470 8*12 245 8*12 275 8*12 370 8*14 400 10*17 520 13*21 600 13*25 700 1000 8*14 314 10*16 430 10*17 512 10*27 550 13*21 590 13*25 740 16*26 870 2200 10*20 730 10*25 780 13*25 1000 16*25 1100 16*35 1610 18*40 1760 25*40 1940 3300 10*25 845 13*21 1030 13*25 1200 16*31 1320 16*35 1610 18*40 1760 25*40 1940 4700 13*25 1240 13*30 1400 16*31 1510 18*31 1580 18*40 1820 22*40 1925 25*45 2146 6800 16*25 1370 16*31 1610 16*35 1620 18*40 1730 22*40 2016 25*40 2172 30*40 2368电压V 容量uf100V 160V 200V 250V 350V 400V 450V SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C.0.47 5*11 10 5*11 12 5*11 12 6.3*11 12 8*11 12 8*11 12 8*12 121.0 5*11 15 5*11 16 5*11 16 6.3*11 16 8*11 16 8*11 16 8*12 162.2 5*11 23 6.3*11 23 6.3*11 23 6.3*12 23 8*11 23 8*12 24 8*14 243.3 5*11 30 8*11 34 8*11 34 8*14 34 10*13 24 10*14 24 10*14 424.7 5*11 37 6.3*11 40 8*11 40 8*12 40 8*14 42 10*12 42 10*17 50 10 6.3*11 56 8*11 60 10*13 60 10*16 70 10*20 70 10*20 76 10*21 75 22 8*11 94 8*14 96 10*12 105 10*14 130 12*21 134 13*25 136 16*25 130 33 10*13 120 10*20 140 13*21 140 13*25 150 16*25 150 16*25 150 16*31 170 47 10*17 150 13*21 160 13*25 165 16*25 170 16*31 180 16*35 210 18*35 190 100 13*21 250 16*25 225 16*25 260 16*35 320 18*40 335 18*40 365220 16*25 450 16*40 493 18*40 520 Case size Ripple current末尽目录,以当时采购为准330 16*25 625 18*40 647470 16*31 780680 18*40 1060Case size Ø D*L (mm), RippleCURRENT [Ma rms] at 105℃ 120Hz NOTE:以上所提供的设计及特性参数谨供参考作用,任何修改不作预先通知.如果在使用上有疑问,请在采购前与我们联络, 以便提供技术上的协助!LEAD FREE TYPE REFLOW SOLDERING CONDITION无 铅 焊 料 产 品 的 回 流 焊 条 件● Recommended Conditions for Reflow Soldering 无铅焊料产品遵循的回流焊条件 (1) Preheat shall be made at 100℃~200℃ and for maximum 180 seconds. 100℃~200℃的预热时间不得超过180秒钟。
电解电容规格书400V10UF ltec
TYPE’SDIMENSIONS(MM)
型状及尺寸
D:
10
L:
16
F:
5
工作电压
400v
容量范围
120Hz 20℃
8~12uf
使用温度
-40~105℃
漏电流
uA
I≤40uA
充电1分钟后
损失角正切值
120Hz 20℃
DF≤0.20
高温特性105℃加电压1000小时
1.I≤标准值
2.△C/C≤30%
3.△CF/CF≤30%
低温特性
≤5
四.铝电解电容器环境特性图
(1)温度特性
C DF I
.
TT T
容量特性损失值特性漏电特性
(2)频率特性
CDF I
T T T容量特性损失值特性漏电特性
typesdimensionsmm型状及尺寸工作电压400v容量范围120hz20812uf使用温度40105漏电流uai40ua充电1分钟后损失角正切值120hz20df020cfcf30低温特性容量特性损失值特性漏电特性容量特性损失值特性漏电特性
一.结构(见附图)
NO.
部位
材料
1
导针
铝99.99%
2
引击线
镀锡铜包钢线
3
胶塞
三元异丙胶
4
套管
PVC热缩材料
5
外壳
铝99.5%
6ቤተ መጻሕፍቲ ባይዱ
正极箔
氧化铝99.99%
7
负极箔
腐蚀铝99.7%
8
隔离物
电解纸
9
粘结体
胶带或胶水
二.标志
商标(1)Ltec
常用电容封装类型与规格
常用电容封装类型与规格电容器是电子元器件中常用的一种元件,用于储存电荷和能量。
电容器封装类型和规格多种多样,下面将介绍常用的电容器封装类型及其规格。
1.陶瓷电容器(Ceramic Capacitor):陶瓷电容器是一种常用的电容器类型之一,由于其体积小、价格低廉,被广泛应用于各种电子电路中。
陶瓷电容器的封装规格一般以贴片(SMD)和插装型为主,常见的尺寸有0402、0603、0805等,其容量范围通常在pF(皮法)至μF(微法)之间。
陶瓷电容器的工作电压一般在几十伏特至数百伏特之间。
2.铝电解电容器(Aluminum Electrolytic Capacitor):铝电解电容器是一种常用的大容量电容器,主要用于储存大电荷和大能量。
铝电容器的封装规格一般以插装型为主,常见的尺寸有Radial、Axial等,其容量范围通常在μF(微法)至mF(毫法)之间。
铝电解电容器的工作电压一般在几十伏特至数百伏特之间。
3.有机电解电容器(Organic Electrolytic Capacitor):有机电解电容器是一种新型的电容器类型,具有高容量、低ESR (等效串联电阻)等优点,广泛应用于高性能电子电路中。
有机电解电容器的封装规格一般以表面贴装(SMD)为主,常见的尺寸有0805、1206等,其容量范围通常在μF(微法)至mF(毫法)之间。
有机电解电容器的工作电压一般在几十伏特至数百伏特之间。
4.铜箔电容器(Polyester Film Capacitor):铜箔电容器是一种常用的高频电容器,用于高频信号的耦合和滤波。
铜箔电容器的封装规格一般以插装型和片式型为主,常见的尺寸有Radial、Axial、SMD等,其容量范围通常在nF(纳法)至μF(微法)之间。
铜箔电容器的工作电压一般在几十伏特至数百伏特之间。
5.电介质电容器(Film Capacitor):电介质电容器是一种常用的高质量和高精度电容器,具有较低的失谐因数和较高的频率响应。
各种电解电容规格大全(直插)1
各种电解电容规格⼤全(直插)1relationship betwee n Government a nd busine ss. T he "two se ssi ons", General Se cretary of "Pro", "cle ar" the wor d succi nctly sum marized t he new relationship betwee n Gov ernment a nd business, as pure politi cs, resha ping the political relati onship specified i n the directi on. District le aders i n ha ndling politi cal and busi ness relati ons, engage i n tradi ng power for money, a nd finally stumbl ed, we a lesson, always kee p in mind that "Pro", "cl ean" pra ctici ng "Pro", "clear". "Pr o" is to open a sincere e ngagement wit h private enter prise t o hel p solve pra ctical difficulties; " Clear "is to clarify the Division of pow er, exerci sed i n accor dance wit h, private e ntrepre neurs with i nnoce nt purit y, not abusi ng power for per sonal gain, not to e ngage in tra ding power for money. Thir d, in order t o maintain fairness a nd justice. Fairness and justice i s the lifeli ne of the r ule of la w , is t he be st devel opme nt environme nt. Currentl y, lax law enf or cement a nd t he judici al se ctor in our regi on al so exist t o varying degrees, la w enforceme nt de partments a nd i ndivi dual window units power for persona l gains and bri bes, thi ck friends, relati ons, human cases, money cases i n whi ch seri ously infringe on t he legitimate rig hts and i nterests of e nterpri ses a nd pe ople. Especially some law e nforcement and inspe ction for pr ofit purpose s, deliberately l ooki ng for cor porate loophol es, found dire ctly under the ti cket does not give busine ss impr ovement opportunities. We re cruit a com pany doesn't easily, cultivati ng a busi ness more difficult, never for personal gai n, systemati c harassment, card, last che cked to check t o ge t the enter prise coll apse d. o g uarantee t he legitimate rig hts a nd i nterests. Al ways pr ocee d from the overall situati on of reform and devel opment of servi ces, f ully consider t he chara cteristics of pr oduction a nd ma nagement i n non -publi c e nterprises a nd social benefits, a n a ccurate grasp of legal limits, prote ct the enthusia sm of entre preneurs a nd practiti oner s in innovation and e ntrepre neurship, enhancing expectations a nd confi dence. To pr omote stri ct enforceme nt. Strengt heni ng law enfor cement procedures, impr ove law enfor cement performance evaluati on, strengthe ning t he supervi sion of law e nforcement, ex plorati on a nd pra ctice of risk control me cha nism of law e nforceme nt to further sta ndardize t he social security, urba n management , r oad traffic admi nistrative law enfor cement, effectively free, extensive law -enfor cement a nd lax enfor cement of law enforcement and ot her issues. o uphol d justi ce. Justice i s the last li ne of Defe nse to safeguard fairne ss a nd justice , to unequivocall y support the courts and pr ocuratorates independently exerci se level ... Judi cial a ctivities were rampa nt, must not be allowe d to run, favors, money, must not be all owe d to knowingly vi olate the miscarriage, vi olations of the l egitimate rights and interest s of t he masses must not be allowe d to a buse of power, to make forest mass ca n be felt in every judicial cases i n e quity and justice. Four to dee pen grass-r oots governance a ccording t o lawchain do l ong, a nd put scale big. To serve the devel opment of enterpri ses. Duocuo simulta neously impr oving service efficie ncy, build better publi c servi ces platform, e nha nce work efficie ncy, initiative to help busine sses solve the project pr oce dure s, financing l oans, issues such as land-use a ppr oval, reduce operati ng costs, busi ness travel light a nd e nha nce the confi dence to over come all ki nds of difficultie s and the Foundation, real entre prene urial pa ssi on play entrepre ne urshi p, e nha nce t he inter nal vitality and creativity. SI XING an construction, pr omoting the rule of law, trie s to make the transformation of forest development XI Ge neral Secretary stressed, to reinvigorate Northeast China, optimize d devel opme nt environment is very important. E nvironme nt of rule of law most gather M oss, the most conducive to development. Improvi ng the lea ding ca dres ' usi ng the method of thought and the r ule of law Admi nistration work, probl em -solving , the ability to pr omot the devel opme nt, is t he key to promoti ng the rule of law. The law may affect the efficiency of out of the path of deve lopme nt will be m ore smooth, won devel opme nt gains will be sustained, a nd end with greater efficiency. Lea ding cadres at all level s shoul d take the lead in re spe ct of law la w, a bide by, and actively foster Socialist culture , actively promoti ng the field of multi-level governa nce accor ding t o law, gui de the masses and consciously abide by t he la w, failing t o find law, solve the problem by la w , i n accor dance wit h the law preva il. XXX admi nistration by law of leadi ng ca dres do not exist on t he rul e of la w , law enforceme nt, ca sual , and vow not t o invest ors, t he new scores and other turmoil. T hese im portant ex positions on my distri ct create g ood development e nvironme nt with highly targeted and gui dance, especially t he General Se cretary pointe d out that t he chaos in my area al so exist s to varying degree s, some eve n quite seri ous. Leadi ng ca dres at all l evels must improve t he development envir onme nt of rule of law as a fundamental task, a dhere t o the pr oblem oriente d, sol id and solve the probl ems in the constr uction of rule of law, to r ule the new effect for devel opme nt environment impr ovements. To hold "key minority". Leaders of this gr oup, although few i n num ber, but the effect is critical. If a local lea ders take the lead right a ccordi ng to law, i n accor dance with t he law, the local CPPCC fresh, pragmatic and efficient development e nvironme nt. Converse ly, if a local leaders of ignoring the la w , impunit y, not only t he political e nvironment will be destr oyed, will have seri ous implicati ons for the dev elopment envir onment. Now , some leadi ng ca dres la ck of awarene ss on the importance of lear ning, t hat learn or not does not matter. T hink efficie ncy is t oo low too m uch, act a ccor ding to t he pr oce dure, t han a n executive order getting al ong wit h. In deali ng with complex issues, often speak of "settling" and "done"; on the i ssue of handli ng letters and visits, like to spe nd money and buy stop a nd stable, but di sregard the law admi nistration, in accor dance wit h the la w, the r ulechain do l ong, a nd put scale big. To serve the devel opm ent of enterprises. Duocuo simulta neously impr oving se rvice efficie ncy, build better publi c servi ces platform, e nha nce w ork efficiency, initiative to hel p businesse s solve t he pr oject procedures, fina nci ng loa ns, issue s such a s land-use a pproval, re duce operating costs, busine ss travel light and enha nce the confide nce t o overcome all kinds of difficulties a nd the Foundati on, real e ntrepre neuri al passion play entre preneurship, e nhance the internal vitality and creativity. SI XING an construction, prom oting the r ule of la w , tries to make the transformation of forest development XI Ge neral Secretary stre sse d, to reinvig orate Nort heast China, optimize d devel opme nt environment is very im portant. E nvironment of rule of law most gather Moss, the most conducive t o devel opme nt. Improvi ng the lea ding cadres ' usi ng the method ofthoug ht and the rule of law Admini stration w ork, pr oblem -solving, t he ability to pr omote the devel opment, i s the key to promoti ng the r ule of law. T he law may affect the efficie ncy of out of the pat h of devel opme nt will be more sm ooth, won devel opme nt gains will be sustaine d, and end wit h greater efficie ncy. Lea ding cadres at a ll levels should take t he lea d in respe ct of law la w, abi de by, a nd a ctively foster Socialist culture , actively promoti ng the fiel d of multi-l evel gover nance accor ding to la w, g uide t he masse s and consci ously abide by the law, faili ng to find law, solve t he pr obl em by law, in a ccordance with t he law prevail. XXX admi nistration by law of lea ding cadres do not exist on t he rule of law , la w enfor cement, casual, and vow not to i nvestors, the new score s and other turmoil. The se important expositions on my distri ct create g ood devel opme nt environment wit h hig hly targeted a nd gui dance, e spe cially the Ge neral Secretary poi nted out that the chaos in my area also exists to varyi ng degre es, some eve n quite seri ous. Lea ding cadre s at all level s must impr ove the devel opment environment of rule of law a s a fundame ntal task, a dhere t o the problem ori ented, soli d and solve the problems i n the construction of rul e of la w, to r ule the new effect for devel opment e nvironment impr ovements. To hold "key minority". Lea ders of this group, although few in numbe r, but the effect is criti cal. If a l ocal l eaders take the lea d right a ccordi ng to la w , in a ccorda nce with t he la w , the l oca l CPPCC fresh, pragmatic a nd efficie nt devel opme nt envir onment. Conversel y, if a local lea ders of ignori ng the law, impunity, not only t he political environment w ill be destroye d, w ill have serious impl ications for t he development envir onme nt. Now, some l eadi ng ca dres la ck of aware ness on t he importance of lear ning, that lear n or not does not matter. Thi nk efficiency is too l ow too much, a ct according to t he pr oce dure, t han an executive order getting al ong with. In dealing with complex i ssue s, ofte n speak of "settling" and "done"; on the i ssue of handli ng letters and visits, like to spe nd money and buy stop and stable, but disregard the law administration, i n accor dance with t he law, the rul rass-r oots g overna nce accordi ng to law i s an importa nt foundation for pr omoting t he constr ucti on of rule of la w, but also the m ost ba sic devel opment e nvironment. De spite my good social or der in General, but there are law-a bidi ng consci ousness, social order i s not standard, regar dless of faith, Twining vi sit visit and ot her outstanding problems. We want t o actively promote t he field of multi-level governa nce accor ding to la w, promote t he conti nuous im provement of the socia l environment. o promote univer sal complia nce. Actively foster t he rul e of law culture , carry out law publicit y and e ducation on honesty a nd tr ustwort hine ss, guide t he masse s and consci ously abi de by t he law, failing to fi nd method, problem-solvi ng method, method of gradually cha nging t he worl d, he is not l ooki ng for but some one "unspoke n rule s", formed all law law abide by t he good atmosphere. T o stre ngthe n the com prehe nsive ma nagement of public security. Deepeni ng pea ce xinga n constr ucti on, strongly against viole nce crime, mafia and serious criminal offences, to prote ct the legitimate rights a nd intere sts of citize ns, legal persons, carry out criminal pol icy of temper justice with mercy, the maximum stimulati ng social vitality, and e arnestly safeguard socia l harmony and stabilit y. To resolve social confli cts by law. To further sm ooth cha nnels of reporting soci al conditi ons and public opi nion, improvi ng regulati on, ar bitration, as well a s dispute resoluti on me cha nisms, im plement fully the petitioners ' ca ses "thir d-party" hearings a nd supervisi ng system of letters and calls, and t o resolve t he involved law law suit int o the or bit of rule of law , vexatious, Twini ng visit visit, distur bing soci al order and other mali cious extortion, resolutely crack dow n. Five, impr oving ca dres V itale, pr ovide str ong pr otecti on for forest devel opme nt XI General Se cretary stresse d that the com prehe nsive revitaliza tion in Northeast China, needs a hig h quality, solid style, ca dres of the dare to play. Ca dre ca dres is a pledge , shoul d want to do work a nd a ble to do good, e nthusiasm i s paramount. Treat party ca dres, it is necessary to Stri ct management, and warm care, e nable t he br oad masses of ca dres w ork har d work, this is tw o parallel principle s. In strict accor dance wit h the sta ndards of good ca dres selecti on a nd a ppoint ment, the real officer s, dare officers, those w ho wa nt to pla y, good a s excelle nt cadre s at all levels of lea dership i n the pa st. At prese nt, some l eadi ng cadre s work i nitiative is not hig h, bey ond politi cal, i dle, lazy g overna nce g overna nce , not a s, slow , messy and a phenomenon still exist t o v arying de grees, affected and restricte d economic and social development. We must mobilize t he ent husiasm of ca dres as a n urgent task , adhere to combi nation of incentive s and constraints, and adhere to the strict manag ement and warm care, practi cal sol utio n "for the officers not to" pr oblem, m otivate cadres a nd better lead the masses t o an undertaking, t he ca dres and create t he ne w achievement i n a dare to play, good at show s as new. To i dentify the probl em, accurate pulse of law to visit and contribute to make visits to t he vexatious visits arroga nce. On t hese i ssues, we need to have a pr oper understanding, shoul d take the lead t o establi sh a se nse of fear of the law, stre ngthe n the application of the rule of law and the r ule of law work of thinki ng and take up responsi bility for the construction of the rule of law. Put lear ning first. Premise is ignorant of the la w , abi de by t he law. Lea ding cadres at all leve ls should take the lea d in st udyi ng the Constit ution and laws a nd regulati ons cl osely relate d to wor k assumed by, a n accurate grasp of the ba sic positi on of our party to a ddre ss the i ssue of the rul e of law , k now n for the scale to do thi ngs, figure out how to use it right, w hat thing s do, what not to do, it ca n never "legal literacy". To enhance the awarene ss of the r ule of law. Firmly establi sh the supremacy of constit utional law , l egal equality before the, right by the law makes the right to statutor y, as well a s the rule of law, devel op habit s of rule of law , t o di scard t he rul e and ca nnot, must not get overri dden by authority, at t he right pressure. Shoul d take the l ead to abi de by. Fulfil its ma ndate i n strict a ccorda nce with stat utory aut hority a nd procedures, no matter what y ou wa nt to a dhere t o the la w, thought of rule by la w and the r ule of law to tackle hot i ssues, effective statut ory duty must be, without a uthorization, is not avail able. Such as construction areas, some cadres are be cause there is no pr oce dure i s followe d by t he rul es, paid a heavy pri ce, we shoul d lear n from them, in strict a ccor dance with t he law on bidding a nd im plementati on ... Pr omised t o give preferential poli cies for enterpri ses, hesita nt to ca sh or cash not at all. Ma sse s feel strongly about the se issues, it is nece ssary to be solved. T o accelerate de ce ntralization. Spe cificati on list li st list of powers, re sponsibil ities and negative, clearance, rev ocation does not a dapt to t he current situati on of t he devel opme nt of policy docume nts, espe cially the rig ht to admi nistrative examination a nd a pproval , the cancellation must be ca nceled, t he delegation must be de ce ntralized to achieve zero-wait, one-st op, seamless, improve administrative efficie ncy a nd service levels. In particular, t he del egation of powers must be caught properly, never abl e to loft is no answ er, no one cares, cause ba ckfire, people work harde r. To carry out t he campaign. Crack dow n on law e nforceme nt regulations, uncivil a nd not as, as undermining economi c deve lopme nt, such as e nvironme ntal pr oblems, pay cl ose attention to the gra ss-r oots l evel we aknesse s, stri ctly investigate and deal with t he grass -roots level corruption and denial of Justice against t he interest s of the masses, such as corr upti on a nd corr uption, rut hless pe opl e around "flies", further optimization of the development e nvironment. In parti cula r, strengt heni ng the constructi on of Governme nt cre dit, and trustw orthy pra ctice for companie s and invest ors, and must not break faith with t he people, pr omises a nd t he pr omise to the society. To buil d a newof law to visit a nd contribute to make visits to t he vexatious visits arroga nce. On these i ssues, we nee d to have a proper understa ndi ng, should take the lea d to esta blish a se nse of fear of the law, stre ngthe n the a ppli cation of the rul e of law and t he rule of law work of thinki ng and take up responsi bility for the construction of the rul e of law. Put le arni ng first. Premise is ig nora nt of the la w , abi de by the law. Lea ding cadres at all lev els should take the le ad in studyi ng the Constituti on a nd law s and regulations closely related to work assumed by, an accurate grasp of the ba sic positi on of our party t o addre ss the i ssue of the r ule of law, known for the scal e to do thing s, figure out how to use it right, w hat thing s do, what not to do, it ca n never "legal litera cy". T o e nha nce the aware ness of the rul e of law. Firmly establi sh the suprema cy of constit utional law , l egal equality before t he, right by t he law makes the right to statut ory, a s well a s the rule of law , develop ha bits of rule of law, to discard the rule a nd cannot, must not get overri dden by a uthority, at the right pre ssure. Should take t he lead t o abi de by. Fulfil its ma ndate i n strict a ccor dance wit h statutory a uthority and procedures, no matter what you want t o adhere to the law, thoug ht of rule by la w and the r ule of law to ta ckle hot iss ues, effective stat utory duty must be , without a uthori zation, is not availabl e. Such a s construction areas, some cadres are because there is no procedure is foll owed by the rul es, paid a heavy price, we should le arn from them, i n strict a ccordance with the law on bi ddi ng and impleme ntation ... Pr omised t o give preferential poli cies for e nterprise s, he sitant to cash or ca sh not at all. Ma sses feel str ongly a bout these i ssues, it is necessary to be solved. T o a ccelerate de centralizati on. Spe cification list list list of power s, responsibilities a nd negative, clearance, revocation does not ada pt to the curre nt situati on of the devel opme nt of policy documents, espe cially the rig ht to admi nistrative examination a nd a pproval , the cancellation must be ca nceled, t he delegation must be de ce ntralized to achieve zero-wait, one-st op, seamless, improve a dministrative efficie ncy a nd service levels. In particular, t he del egation of powers must be caught properly, never abl e to loft is no answ er, no one cares, cause ba ckfire, people work harde r. To carry out t he campaign. Crack dow n on law e nforceme nt regulations, uncivil a nd not as, as undermining economi c deve lopme nt, such as e nvironme ntal pr oblems, pay cl ose attention to the gra ss-r oots l evel we aknesse s, stri ctly investigate and deal with t he grass-roots level corruption and denial of Justice against t he interest s of the masses, such as corr upti on a nd corr uption, rut hless pe opl e around "flies", further optimization of the development e nvironment. In parti cula r, strengt heni ng the constructi on of Governme nt cre dit, and trustw orthy pra ctice for companie s and invest ors, and must not break faith with t he people, pr omises a nd the promi se to the society. To buil d a new 5ALUMINUM ELECTROLYTIC CAPACITORS SPECIFICATION FOR APPOV AL 铝电解电容器规格承认书表1:承认项⽬ Type DimensionsCustomer客户Vendor供应商 Heng Xin Da Electronic Co.Ltd恒新达电⼦有限公司Used Spec通⽤规格 3300UF/50VProduct Name 品名Aluminum Electrolytic Capacitor铝电解电容器 Size φD ×L(mm) 外型尺⼨18*34 Operating Temperature Rage使⽤温度-40~+105℃ Rated V oltages Range(V) 额定电压50VCapacitance Tolerance(20℃,120Hz)容量范围±20% 下限: 2640UF 上限: 3960UFβαLead Spacing and Wine Diameter(mm)型状及尺⼨d ±0.005ΦD ±β(电容直径)18mm ±0.5 L ±a(电容⾼度)34mm ±2.0P ±0.5(脚距)10mm ±0.5Φd (引线直径) 0.8 mm ±0.05表2:额定值与特性 TABLE1 RATING&CHARACTERISTIC.1 泄漏电流 I施加额定电压1分钟I=0.01CV 或+3uA 即0.01×容量×电压的读数之内为合格品2损耗⾓正切〥(120Hz)U R/V 6.3V 10V 16V25V35V50V100V 200V 400V 450Vtgδ0.280.240.200.160.140.120.080.200.250.253 耐久性(105°C)试验时间3000h (施加额定标称纹波电流电压)1:漏电流, 不超过序号1规定值,(施加额定⼯作电压60秒读数)2:电容量变化率, U R ≤6.3V; ΔC/C ≤+20%~30% 6.3V测试频率:120Hz额定⼯作电压(V)6.3 10 16 25 50 200 400 450 阻抗⽐ZT/Z20max)Z-25℃/Z+20℃ 2 2 2 2 2 2 3 8 Z-40℃/Z+20℃444333495 ⾼温负荷特性在105℃环境中施加额定⼯作电压1000⼩时后, 电容器的特性符合右表的要求.静电容量变化率初始值的±20%之内损耗⾓正切不⼤于初始值的200% 漏电流不⼤于初始值6 ⾼温储存特性在105℃环境中⽆负荷放置2000⼩时后,电容器的特性符合序号5中所列规定值. 7耐焊接热特性经过回流焊并冷却⾄室温后, 电容器的特性符合右表的要求.静电容量变化率初始值的±10%之内损耗⾓正切不⼤于初始值漏电流不⼤于初始值⽣产⼚商签章: 客户承认签章:relationship betwee n Government a nd busine ss. T he "two se ssi ons", General Se cretary of "Pro", "cle ar" the wor d succi nctly sum marized t he new relationship betwee n Gov ernment a nd business, as pure politi cs, resha ping the political relati onship specified i n the directi on. District le aders i n ha ndling politi cal and busi ness relati ons, engage i n tradi ng power for money, a nd finally stumbl ed, we a lesson, always kee p in mind that "Pro", "cl ean" pra ctici ng "Pro", "clear". "Pr o" is to open a sincere e ngagement wit h private enter prise t o hel p solve pra ctical difficulties; " Clear "is to clarify the Division of pow er, exerci sed i n accor dance wit h, private e ntrepre neurs with i nnoce nt purit y, not abusi ng power for per sonal gain, not to e ngage in tra ding power for money. Thir d, in order t o maintain fairness a nd justice. Fairness and justice i s the lifeli ne of the r ule of la w , is t he be st devel opme nt environme nt. Currentl y, lax law enfor cement a nd t he judici al se ctor in our regi on al so exist t o varying degrees, la w enforceme nt de partments a nd i ndivi dual window units power for persona l gains and bri bes, thi ck friends, relati ons, human cases, money cases i n whi ch seri ously infringe on t he legitimate rig hts and i nterests of e nterpri ses a nd pe ople. Especially some law e nforcement and inspe ction for pr ofit purpose s, deliberately l ooki ng for cor porate loophol es, found dire ctly under the ti cket does not give busine ss impr ovement opportunities. We re cruit a com pany doesn't easily, cultivati ng a busi ness more difficult, never for personal gai n, systemati c harassment, card, last che cked to check t o ge t the enter prise coll apse d. o g uarantee t he legitimate rig hts a nd i nterests. Al ways pr ocee d from the overall situati on of reform and devel opment of servi ces, f ully consider t he chara cteristics of pr oduction a nd ma nagement i n non -publi c e nterprises a nd social benefits, a n a ccurate grasp of legal limits,prote ct the enthusia sm of entre preneurs a nd practiti oner s in innovation and e ntrepre neurship, enhancing expectations a nd confi dence. To pr omote stri ct enforceme nt. Strengt heni ng law enfor cement procedures, impr ove law enfor cement performance evaluati on, strengthe ning t he supervi sion of law e nforcement, ex plorati on a nd pra ctice of risk control me cha nism of law e nforceme nt to further sta ndardize t he social security, urba n management , road traffic admi nistrative law enfor cement, effectively free, extensive law -enfor cement a nd lax enfor cement of law enforcement and ot her issues. o uphol d justi ce. Justice i s the last li ne of Defe nse to safeguard fairne ss a nd justice , to unequivocall y support the courts and pr ocuratorates independently exerci se level ... Judi cial a ctivities were rampa nt, must not be allowe d to run, favors, money, must not be all owe d to knowingly vi olate the miscarriage, vi olations of the l egitimate rights and interest s of the masses must not be allowe d to a buse of power, to make forest mass ca n be felt in every judicial cases i n e quity and justice. Four to dee pen gras s-r oots governance a ccording t o lawchain do l ong, a nd put scale big. To serve the devel opment of enterpri ses. Duocuo simulta neously impr oving service efficie ncy, build better publi c servi ces platform, e nha nce work efficie ncy, initiative to help busine sses solve the project pr oce dure s, financing l oans, issues such as land-use a ppr oval, reduce operati ng costs, busi ness travel light a nd e nha nce the confi dence to over come all ki nds of difficultie s and the Foundation, real entre prene urial pa ssi on play entrepre ne urshi p, e nha nce t he inter nal vitality and creativity. SI XING an construction, pr omoting the rule of law , trie s to make the transformation of forest development XI Ge neral Secretary stressed, to reinvigorate Northeast China, optimize d devel opme nt environment is very important. E nvironme nt of rule of law most gather M oss, the most conducive to development. Improvi ng the lea ding ca dres ' usi ng the method of thought and the r ule of law Admi nistration work, probl em-solving , the ability to pr omot the devel opme nt, is t he key to promoti ng the rule of law. The law may affect the efficiency of out of the path of deve lopme nt will be m ore smooth, won devel opme nt gains will be sustained, a nd end with greater efficiency. Lea ding cadres at all level s shoul d take the lead in re spe ct of law la w, a bide by, and actively foster Socialist culture , actively promoti ng the field of multi-level governa nce accor ding t o law, gui de the masses and consciously abide by t he la w, failing t o find law, solve the problem by la w, i n accor dance wit h the law preva il. XXX admi nistration by law of leadi ng ca dres do not exist on t he rul e of la w , law enforceme nt, ca sual , and vow not t o invest ors, t he new scores and other turmoil. T hese im portant ex positions on my distri ct create g ood development e nvironme nt with highly targeted and gui dance, especially t he General Se cretary pointe d out that t he chaos in my area al so exist s to v arying degree s, some eve n quite seri ous. Leadi ng ca dres at all l evels must improve t he development envir onme nt of rule of law as a fundamental task, a dhere t o the pr oblem oriente d, sol id and solve the probl ems in the constr uction of rule of law, to r ule the new effect for devel opme nt environment impr ovements. To hold "key minority". Leaders of this gr oup, although few i n num ber, but the effect is critical. If a local lea ders take the lead right a ccordi ng to law, i n accor dance with t he law, the local CPPCC f resh, pragmatic and efficient development e nvironme nt. Converse ly, if a local leaders of ignoring the la w , impunit y, not only he political e nvironment will be destr oyed, will have seri ous implicati ons for the dev elopment envir onment. Now , some leadi ng ca dres la ck of awarene ss on the importance of lear ning, t hat learn or not does not matter. T hink efficie ncy is t oo low too m uch, act a ccor ding to t he pr oce dure, t han a n executive order getting al ong wit h. In deali ng with complex issues, often speak of "settling" and "done"; on the i ssue of handli ng letters and visits, like to spe nd money and buy stop a nd stable, but di sregard the law admi nistration, in accor dance wit h the la w, the r ulechain do l ong, a nd put scale big. To serve the devel opment of enterprises. D uocuo simulta neously impr oving se rvice efficie ncy, build better publi c servi ces platform, e nha nce w ork efficiency, initiative to hel p businesse s solve t he pr oject procedures, fina nci ng loa ns, issue s such a s land-use a pproval, re duce operating costs, busine ss travel light and enha nce the confide nce t o overcome all kinds of difficulties a nd the Foundati on, real e ntrepre neuri al passion play entre preneurship, e nhance the internal vitality and creativity. SI XING an construction, prom oting the r ule of la w , tries to make the transformation of forest development XI Ge neral Secretary stre sse d, to reinvig orate Nort heast China, optimize d devel opme nt environment is very im portant. E nvironment of rule of law most gather Moss, the most conducive t o devel opme nt. Improvi ng the lea ding cadres ' usi ng the method of thoug ht and the rule of law Admini stration w ork, pr oblem -solving, t he ability to pr omote the devel opment, i s the key to promoti ng the r ule of law. T he law may affect the efficie ncy of out of the pat h of devel opme nt will be more sm ooth, won devel opme nt gains will be sustaine d, and end wit h greater efficie ncy. Lea ding cadres at a ll levels should take t he lea d in respe ct of law la w, abi de by, a nd a ctively foster Socialist culture , actively promoti ng the fiel d of multi-l evel gover nance accor ding to la w, g uide t he masse s and consci ously abide by the law, faili ng to find law, solve t he pr obl em by law, in a ccordance with t he law prevail. XXX admi nistration by law of lea ding cadres do not exist on t he rule of law , la w enfor cement, casual, and vow not to i nvestors, the new score s and other turmoil. The se important expositions on my distri ct create g ood devel opme nt environment wit h hig hly targeted a nd gui dance, e spe cially the Ge neral Secretary poi nted out that the chaos in my area also exists to varyi ng degre es, some eve n quite seri ous. Lea ding cadre s at all level s must impr ove the devel opment environment of rule of law a s a fundame ntal task, a dhere t o the problem ori ented, soli d and solve the problems i n the construction of rul e of la w, to r ule the new effect for devel opment e nvironment impr ovements. To hold "key minority". Lea ders of this group, alt hough few in numbe r, but the effect is criti cal. If a l ocal l eaders take the lea d right a ccordi ng to la w, in a ccorda nce with t he la w, the l oca l CPPCC fresh, pragmatic a nd efficie nt devel opme nt envir onment. Conversel y, if a local lea ders of ignori ng the law, impunity, not only t he political environment w ill be destroye d, w ill have serious impl ications for t he development envir onme nt. N ow, some l eadi ng ca dres la ck of aware ness on t he importance of lear ning, that lear n or not does not matter. Thi nk efficiency is too l ow too much, a ct according to t he pr oce dure, t han an executive order getting al ong with. In dealing with complex i ssue s, ofte n speak of "settling" and "done"; on the i ssue of handli ng letters and visits, like to spe nd money and buy stop and stable, but d isregard the law administration, i n accor dance with t he law, the rul rass-r oots g overna nce accordi ng to law i s an importa nt foundation for。
贴片电解电容封装尺寸
贴片电解电容封装尺寸1. 引言贴片电解电容是一种常用的被动元件,广泛应用于电子产品中。
它具有体积小、重量轻、功率密度高等特点,因此在现代电子设备中占据重要地位。
而贴片电解电容的封装尺寸则是其设计和应用过程中需要考虑的关键因素之一。
2. 贴片电解电容的基本结构贴片电解电容由两个极板之间夹着一层氧化铝薄膜构成。
其中,正极板由铝箔制成,负极板通常采用碳材料。
两个极板之间的氧化铝薄膜起到绝缘和储存电荷的作用。
为了提高储存容量,氧化铝薄膜通常会经过阳极氧化处理。
3. 封装尺寸对性能的影响贴片电解电容的封装尺寸直接影响着其性能和应用范围。
下面将从几个方面详细介绍。
3.1 容量贴片电解电容的容量与其表面积和厚度有关。
封装尺寸较大的贴片电容通常具有较大的表面积,从而可以提供更大的容量。
而厚度的增加也会增加电容的容量。
因此,在设计贴片电解电容时,需要根据实际需求选择合适的封装尺寸来满足所需的容量。
3.2 额定电压贴片电解电容的额定电压是指其能够承受的最大工作电压。
封装尺寸对额定电压有直接影响。
较大尺寸的贴片电容通常具有更高的额定电压,这是因为其结构可以提供更好的绝缘性能和耐压能力。
3.3 工作温度范围贴片电解电容在工作过程中会产生一定的热量,因此其工作温度范围也是需要考虑的因素之一。
较小封装尺寸的贴片电容由于散热面积小,通常具有较低的工作温度范围。
而较大封装尺寸则可以提供更好的散热性能,具有更广泛的工作温度范围。
3.4 安装方式贴片电解电容可以通过表面贴装(SMT)方式进行安装。
封装尺寸直接影响着其在SMT过程中的安装效率和可靠性。
较小封装尺寸的贴片电容通常更容易精确地安装到PCB上,而较大尺寸的贴片电容则需要更多的空间和精度。
4. 常见贴片电解电容封装尺寸根据国际标准,贴片电解电容有多种常见的封装尺寸,如0805、1206、1210等。
这些数字代表了其长宽尺寸,以英寸为单位。
其中,0805是指长为0.08英寸、宽为0.05英寸的贴片电容。
贴片铝电解电容耐压规格
全称:贴片铝电解电容器,简称:片式铝电解,片铝等。
主要规格尺寸,接公制标准分为:4*5.5mm, 5*5.5mm, 6.3*5.5mm, 6.3*7.7mm, 8*6.2mm, 8*10.2mm, 10*10.2mm, 10*12mm等。
220uf6.3v 贴片电容|SMD电容器|铝电解电容器|片式电容|片铝|片式铝电解电容器|贴片电容器220uf6.3v 贴片电容|SMD电容器|铝电解电容器|片式电容|片铝|片式铝电解电容器|贴片电容器470u35v 贴片电容|SMD电容器|铝电解电容器|片式电容|片铝|片式铝电解电容器|贴片电容器10uf25v 贴片电容|SMD电容器|铝电解电容器|片式电容|片铝|片式铝电解电容器|贴片电容器220uf16v 贴片电容|SMD电容器|铝电解电容器|片式电容|片铝|片式铝电解电容器|贴片电容器10uf10v 贴片电容|SMD电容器|铝电解电容器|片式电容|片铝|片式铝电解电容器|贴片电容器铝电解电容器的构成:是由正箔. 负箔和电解纸卷成芯子,用引线引出正负极,含浸电解液后通过导针引出,再用铝壳和胶密密封起来。
片式铝电解电容器体积虽然较小,但是因为通过电化学腐蚀后,电极箔的表面积被扩大了,且它的介质氧化膜非常薄,所以,片式铝电解电容器可以具有相对较大的电容量。
正确选用一颗贴片铝电解电容器产品,要注意的参数包括:电容量. 额定电压.温度. 寿命以及特性(比如高频低阻抗)的要求。
0.47uF50v|50v 0.47uF 4*5.4 0.47uF63v|63v0.47uF 4*5.4 0.47 uF 100v|100v0.47uF 4*5.41uF50v|50v1uF 4*5.4 1uF63v|63v1uF 4*5.4 1uF 100v|100v1uF 6.3*5.42.2uF50v|50v 2.2uF 4*5.4 2.2uF63v|63v1uF 4*5.4 2.2 uF 100v|100v2.2uF 6.3*5.43.3uF35v|35v3.3uF 4*5.4 3.3uF50v|50v3.3uF 4*5.4 3.3uF63v|63v3.3uF 5*5.43.3uF100v|100v3.3uF 6.3*5.44.7uF25v|25v4.7uF 4*5.4 4.7uF35v|35v4.7uF 4*5.4 4.7uF50v|50v4.7uF 5*5.4 4.7uF63v|63v4.7uF6.3*5.4 4.7uF100v|100v4.7uF 6.3*7.76.8uF25v|25v6.8uF 4*5.4 6.8uF35v|35v6.8uF 4*5.4 6.8uF50v|50v6.8uF 5*5.4 6.8uF63v|63v6.8uF 6.3*5.4 6.8uF100v|100v6.8uF 6.3*7.78.2uF25v|25v8.2uF 4*5.4 8.2uF35v|35v8.2uF 4*5.4 8.2uF50v|50v8.2uF 5*5.4 8.2uF63v|63v8.2uF 6.3*5.4 8.2uF100v|100v8.2uF 6.3*7.710uF16v|16v10uF 4*5.4 10uF25v|25v10uF 4*5.4 10uF35v|35v10uF 4*5.4 10uF50v|50v10uF 6.3*5.4 10uF63v|63v10uF 6.3*5.4 10uF100v|100v10uF 6.3*7.722uF6.3v|6.3v22uF 4*5.4 22uF10v|10v22uF 4*5.4 22uF16v|16v22uF 4*5.4 22uF25v|25v22uF 5*5.4 22uF35v|35v22uF 6.3*5.4 22uF50v|50v22uF 6.3*5.4 22uF63v|63v22uF 6.3*7.7 22uF220v|220v22uF 8*10.233uF6.3v|6.3v33uF 4*5.4 33uF10v|10v33uF 4*5.4 33uF16v|16v33uF 5*5.4 33uF25v|25v33uF 5*5.4 33uF35v|35v33uF 6.3*5.4 33uF50v|50v33uF 6.3*7.7 33uF63v|63v33uF 8*10.2 33uF330v|330v33uF 10*10.247uF6.3v|6.3v47uF 4*5.4 47uF10v|10v47uF 5*5.4 47uF16v|16v47uF 5*5.4 47uF25v|25v47uF 6.3*5.4 47uF35v|35v47uF 6.3*5.4 47uF50v|50v47uF 6.3*7.7 47uF63v|63v47uF 8*10.2 47uF470v|470v47uF 10*10.268uF6.3v|6.3v68uF 5*5.4 68uF10v|10v68uF 6.3*5.4 68uF16v|16v68uF 6.3*5.4 68uF25v|25v68uF 8*6.5 68uF35v|35v68uF 8*6.5 68uF50v|50v68uF 8*10.2 68uF63v|63v68uF 10*10.2 68uF680v|680v68uF 10*10.282uF6.3v|6.3v82uF 5*5.4 82uF10v|10v82uF 6.3*5.4 82uF16v|16v82uF 6.3*5.4 82uF25v|25v82uF 8*6.5 82uF35v|35v82uF 8*6.5 82uF50v|50v82uF 8*10.2 82uF63v|63v82uF 10*10.2 82uF820v|820v82uF 10*10.2100uF6.3v|6.3v100uF 5*5.4 100uF10v|10v100uF 6.3*5.4 100uF16v|16v100uF 6.3*5.4 100uF25v|25v100uF 6.3*7.7 100uF35v|35v100uF 6.3*7.7 100uF50v|50v100uF 8*10.2 100uF63v|63v100uF 10*10.2150uF6.3v|6.3v150uF 6.3*5.4 150uF10v|10v150uF 6.3*5.4 150uF16v|16v150uF 6.3*7.7 1220uF6.3v|6.3v220uF 6.3*5.4 220uF10v|10v220uF 6.3*7.7 220uF16v|16v220uF 6.3*7.7 220uF25v|25v220uF 8*10.2 220uF35v|35v220uF 8*10.2 220uF50v|50v220uF 10*10.250uF25v|25v150uF 8*10.2 150uF35v|35v150uF 8*10.2 150uF50v|50v150uF 10*10.2330uF6.3v|6.3v330uF 6.3*7.7 330uF10v|10v330uF 8*10.2 330uF16v|16v330uF 8*10.2 330uF25v|25v330uF 10*10.2 330uF35v|35v330uF 10*10.2470uF6.3v|6.3v470uF 6.3*7.7 470uF10v|10v470uF 8*10.2 470uF16v|16v470uF 8*10.2 470uF25v|25v470uF 10*10.2680uF6.3v|6.3v680uF 8*10.2 680uF10v|10v680uF 10*10.2 680uF16v|16v680uF 10*10.2820uF6.3v|6.3v820uF 8*10.2 820uF10v|10v820uF 10*10.2 820uF16v|16v820uF 10*10.21000uF6.3v|6.3v1000uF 8*10.2 1000uF10v|10v1000uF 10*10.2 1000uF16v|16v1000uF 10*10.21500uF6.3v|6.3v1000uF 10*10.2。
齐全的标准铝电解电容规格
电压规格10V16V25V35V1UF4*75*114*75*114*75*114*75*112.2UF4*75*114*75*114*75*114*75*113.3UF4*75*114*75*114*75*114*75*114.7UF4*75*114*75*114*75*114*75*1110UF4*75*114*75*114*75*114*75*1122UF4*75*114*75*114*75*115*75*1133UF4*75*114*75*115*75*116*75*1147UF4*75*114,5*75*115*75*116*76*1168UF100UF 4,5*75*115,6*75*116*7 6.3*128*76*11,12150UF220UF6*75*126,8*76.3*128*98*128*12330UF8*7 6.3*116,8*128*1210*13,16 470UF6*76*128*98*128*12,1410*151000UF8*1210*13,16,1710*17,2013*202200UF10*1710*2013*20,2516*25 3300UF13*2013*2013*2516*30 4700UF13*2113*2516*2518*32电压规格? 50V63V100V160V250V400V1UF4*75*115*115*116*116*116*122.2UF4*75*115*115*116*128*128*123.3UF4*75*115*115*116*128*128*124.7UF4*75*115*115*118*128*128*12 10UF5*75*115*116*118*1210*1310*15 22UF6*75*115*118*1210*1310*2013*2033UF6*7 6.3*126*1110*1310*2013*2013*25 47UF8*7 6.3*126*1110*1713*2013*2016*25 68UF18*26 100UF8*128*1410*2013*2016*2518*32 150UF16*25220UF10*1310*2013*2516*3022*30330UF10*2012*2016*2518*35470UF10*2013*2016*2522*351000UF13*2516*2522*302200UF16*3018*353300UF19*3622*404700UF21*4225*45CD110系列电容器|6.3V/22000uF引线式电容器\85℃普通品电容器6.3V/220uF小体积电容Φ5*116.3V/330uF小体积电容Φ6.3*116.3V/470uF小体积电容Φ6.3*116.3V/1000uF小体积电容Φ8*11.56.3V/2200uF小体积电容Φ10*206.3V/3300uF小体积电容Φ10*206.3V/4700uF小体积电容Φ12.5*206.3V/6800uF小体积电容Φ12.5*256.3V/10000uF小体积电容Φ16*256.3V/15000uF小体积电容Φ16*35.56.3V/22000uF小体积电容Φ18*4010V/47uF小体积电容Φ5*1110V/100uF小体积电容Φ5*1110V/220uF小体积电容Φ6.3*1110V/330uF小体积电容Φ6.3*1110V/470uF小体积电容Φ8*11.510V/1000uF小体积电容Φ10*12.510V/2200uF小体积电容Φ10*2010V/3300uF小体积电容Φ12.5*2010V/4700uF小体积电容Φ12.5*2510V/6800uF小体积电容Φ16*2510V/10000uF小体积电容Φ16*35.510V/15000uF小体积电容Φ18*35.516V/10uF小体积电容Φ5*1116V/22uF小体积电容Φ5*1116V/33uF小体积电容Φ5*1116V/47uF小体积电容Φ5*1116V/100uF小体积电容Φ5*1116V/220uF小体积电容Φ6.3*1116V/330uF小体积电容Φ8*11.516V/470uF小体积电容Φ8*11.516V/1000uF小体积电容Φ10*1616V/2200uF小体积电容Φ12.5*20 16V/3300uF小体积电容Φ12.5*25 16V/4700uF小体积电容Φ16*2516V/6800uF小体积电容Φ16*35.5 16V/10000uF小体积电容Φ18*35.525V/4.7uF小体积电容Φ5*1125V/10uF小体积电容Φ5*1125V/22uF小体积电容Φ5*1125V/33uF小体积电容Φ5*1125V/47uF小体积电容Φ5*1125V/100uF小体积电容Φ6.3*11 25V/220uF小体积电容Φ8*11.5 25V/330uF小体积电容Φ10*12.5 25V/470uF小体积电容Φ10*12.5 25V/1000uF小体积电容Φ10*20 25V/2200uF小体积电容Φ12.5*25 25V/3300uF小体积电容Φ16*25 25V/4700uF小体积电容Φ16*31.5 25V/6800uF小体积电容Φ18*35.535V/4.7uF小体积电容Φ5*1135V/10uF小体积电容Φ5*1135V/22uF小体积电容Φ5*1135V/33uF小体积电容Φ5*1135V/47uF小体积电容Φ5*1135V/100uF小体积电容Φ6.3*11 35V/220uF小体积电容Φ8*11.5 35V/330uF小体积电容Φ10*12.5 35V/470uF小体积电容Φ10*1635V/1000uF小体积电容Φ12.5*20 35V/2200uF小体积电容Φ16*30 35V/3300uF小体积电容Φ16*35.5 35V/4700uF小体积电容Φ18*35.550V/0.1uF小体积电容Φ5*1150V/0.22uF小体积电容Φ5*1150V/0.33uF小体积电容Φ5*1150V/0.47uF小体积电容Φ5*1150V/1uF小体积电容Φ5*1150V/2.2uF小体积电容Φ5*1150V/3.3uF小体积电容Φ5*1150V/4.7uF小体积电容Φ5*1150V/10uF小体积电容Φ5*1150V/22uF小体积电容Φ5*1150V/33uF小体积电容Φ5*1150V/47uF小体积电容Φ6.3*1150V/100uF小体积电容Φ8*11.5 50V/220uF小体积电容Φ10*12.550V/330uF小体积电容Φ10*1650V/470uF小体积电容Φ12.5*20 50V/1000uF小体积电容Φ16*25 50V/2200uF小体积电容Φ16*35.5 50V/3300uF小体积电容Φ18*35.563V/4.7uF小体积电容Φ5*1163V/10uF小体积电容Φ5*1163V/22uF小体积电容Φ5*1163V/33uF小体积电容Φ6.3*1163V/47uF小体积电容Φ6.3*1163V/100uF小体积电容Φ10*12.5 63V/220uF小体积电容Φ10*1663V/330uF小体积电容Φ10*2063V/470uF小体积电容Φ12.5*20 63V/1000uF小体积电容Φ16*25100V/0.1uF小体积电容Φ5*11 100V/0.22uF小体积电容Φ5*11 100V/0.33uF小体积电容Φ5*11 100V/0.47uF小体积电容Φ5*11 100V/1uF小体积电容Φ5*11100V/2.2uF小体积电容Φ5*11 100V/3.3uF小体积电容Φ5*11 100V/4.7uF小体积电容Φ5*11 100V/10uF小体积电容Φ6.3*11 100V/22uF小体积电容Φ6.3*11 100V/33uF小体积电容Φ8*11.5 100V/47uF小体积电容Φ10*12.5 100V/100uF小体积电容Φ10*20 100V/220uF小体积电容Φ10*12.5 100V/330uF小体积电容Φ16*25 100V/470uF小体积电容Φ16*25 100V/1000uF小体积电容Φ18*40160V/0.47uF小体积电容Φ6.3*11 160V/1uF小体积电容Φ6.3*11 160V/2.2uF小体积电容Φ6.3*11 160V/3.3uF小体积电容Φ6.3*11 160V/4.7uF小体积电容Φ6.3*11 160V/10uF小体积电容Φ8*11.5 160V/22uF小体积电容Φ10*16 160V/33uF小体积电容Φ10*20 160V/47uF小体积电容Φ12.5*25 160V/100uF小体积电容Φ16*25 160V/220uF小体积电容Φ16*35.5 160V/330uF小体积电容Φ18*31.5200V/0.47uF小体积电容Φ6.3*11 200V/1uF小体积电容Φ6.3*11 200V/2.2uF小体积电容Φ6.3*11 200V/3.3uF小体积电容Φ6.3*11 200V/4.7uF小体积电容Φ8*11.5 200V/10uF小体积电容Φ10*12.5 200V/22uF小体积电容Φ10*20 200V/33uF小体积电容Φ12.5*20 200V/47uF小体积电容Φ12.5*20 200V/100uF小体积电容Φ16*25 200V/220uF小体积电容Φ18*35.5250V/0.47uF小体积电容Φ6.3*11 250V/1uF小体积电容Φ6.3*11 250V/2.2uF小体积电容Φ6.3*11 250V/3.3uF小体积电容Φ8*11.5 250V/4.7uF小体积电容Φ8*11.5 250V/10uF小体积电容Φ10*16 250V/22uF小体积电容Φ10*20 250V/33uF小体积电容Φ12.5*25 250V/47uF小体积电容Φ12.5*25 250V/100uF小体积电容Φ16*31.5315V/0.47uF小体积电容Φ6.3*11 315V/1uF小体积电容Φ6.3*11 315V/2.2uF小体积电容Φ8*11.5 315V/3.3uF小体积电容Φ10*12.5 315V/4.7uF小体积电容Φ10*12.5 315V/10uF小体积电容Φ10*20 315V/22uF小体积电容Φ12.5*20 315V/33uF小体积电容Φ10*25315V/47uF小体积电容Φ16*25 315V/100uF小体积电容Φ18*31.5350V/0.47uF小体积电容Φ6.3*11350V/1uF小体积电容Φ6.3*11350V/2.2uF小体积电容Φ8*11.5350V/3.3uF小体积电容Φ10*12.5350V/4.7uF小体积电容Φ10*12.5350V/10uF小体积电容Φ10*20350V/22uF小体积电容Φ12.5*25350V/33uF小体积电容Φ10*25350V/47uF小体积电容Φ16*25350V/100uF小体积电容Φ18*31.5400V/0.47uF小体积电容Φ6.3*11400V/1uF小体积电容Φ6.3*11400V/2.2uF小体积电容Φ8*11.5400V/3.3uF小体积电容Φ10*12.5400V/4.7uF小体积电容Φ10*12.5400V/10uF小体积电容Φ10*20400V/22uF小体积电容Φ12.5*25400V/33uF小体积电容Φ10*25400V/47uF小体积电容Φ16*31.5450V/0.47uF小体积电容Φ8*11.5450V/1uF小体积电容Φ8*11.5450V/2.2uF小体积电容Φ10*12.5450V/3.3uF小体积电容Φ10*12.5450V/4.7uF小体积电容Φ10*20450V/10uF小体积电容Φ12.5*25450V/22uF小体积电容Φ10*25450V/33uF小体积电容Φ16*31.5450V/47uF小体积电容Φ16*35.5(注:素材和资料部分来自网络,供参考。
常用电解电容尺寸规格
5.0
47
12.5
25
230
0.15 2000
0.6
5.0
5.0
100
16
31.5
365
0.15 2000
0.8
7.5
1
6.3
11.2
18
0.20 2000
0.5
2.5
5.0
2.5
2.2
8
11.5
31
0.20 2000
0.6
3.5
5.0
3.3
10
12.5
38
0.20 2000
0.6
5.0
5.0
4.7
0.6
3.5
5.0
1000
10
12.5
460
0.24 2000
0.6
5.0
5.0
2200
10
20
760
0.26 2000
0.6
5.0
5.0
10 3300 12.5
20
1000
0.28 2000
0.6
5.0
5.0
4700 12.5
25
1260
0.30 2000
0.6
5.0
5.0
6800
16
25
1570
0.34 2000
0.8
7.5
7.5
10000 16
31.5
1890
0.42 2000
0.8
7.5
15000 18
35.5
2180
0.52 2000
0.8
7.5
100
5
11
110