阳光逆变器检修手册..
光伏逆变器故障诊断与维修

光伏逆变器故障诊断与维修随着清洁能源的持续推广,光伏发电已经成为了一种常见的发电方式。
针对于光伏发电系统而言,逆变器是一种十分重要的设备。
逆变器的主要作用是将光伏电池板发出的直流电转换为交流电,以便于直接供电或者并入电网中。
然而,在使用过程中,逆变器难免会出现一些故障,而故障的发生会极大地影响其性能。
因此,本文将详细探讨光伏逆变器故障的诊断和维修。
一、逆变器故障前兆在逆变器故障之前,通常会有一些明显的前兆。
例如输出电压、电流或功率波形的异常,导致逆变器的输出效率急剧下降。
在这种情况下,应该及时采取措施来排除故障,以免发生更大的损失。
以下是逆变器故障的一些常见症状。
1. 光伏电池板输出电压异常当光伏电池板输出电压异常时,这通常是逆变器发生了故障的一个明显标志。
在正常情况下,逆变器的输出电压应保持稳定,但如果输出电压出现波动或者异常,就需要考虑设备是否需要维修了。
2. 电能发生器输出电流异常逆变器本质上是一个电能发生器,因此,当输出电流异常时,这表明逆变器的性能有问题。
一般情况下,逆变器的输出电流和电压是成比例的,如果两者不能同时达到正常水平,则输出电流可能会变得异常。
3. 输出功率异常逆变器的输出功率通常是不稳定的, 如果输出功率发生了异常,很可能是设备发生了问题。
为了保证光伏发电系统的正常运行,必须及时解决故障。
二、逆变器故障原因1. 组件老化逆变器的寿命通常在不到10年,因此,长期使用会导致其组件老化,这可能会导致逆变器出现故障。
2. 温度过高高温是电子设备过早失效的主要原因之一,如果环境温度过高,就会导致设备过热、电路损坏甚至爆炸。
因此,在安装逆变器时,应该考虑到环境温度,避免过热。
3. 电路短路电路短路是逆变器故障的一个常见原因,这可能是由于电缆或者其他部分在使用过程中破裂引起的,因此,在使用逆变器时应该注意保护电路。
三、逆变器故障诊断方法一旦逆变器出现故障,它的输出电流和电压将发生变化,因此,我们可以通过检测比较逆变器的输出电流和电压来确定故障的类型。
阳光SL3000单相逆变电源定期维护作业指导书

阳光SL3000单相逆变电源定期维护作业指导书编写:年月日审核:年月日批准:年月日工作负责人:作业日期年月日时至年月日时安徽省电力公司第 1 页共8 页1 实用范围本指导书适用于××供电公司调度自动化专业人员的作业行为,适用于××供电公司阳光SL3000逆变电源定期维护工作。
2 引用文件下列标准中的条款通过本作业指导书的引用而成为本作业指导书的条款。
凡是注日期的引用标准,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本作业指导书。
然而,鼓励根据本作业指导书达成协议的各方研究是否可使用这些标准的最新版本。
凡是不注日期的引用标准,其最新版本适用于本作业指导书。
国家电网公司电力安全工作规程(变电站和发电厂电气部分)(试行)DL 5003—91 电力系统调度自动化设计规范DL 516—93 电网调度自动化运行管理规程DL/T590—94 地区电网调度自动化功能规范GB/T13730-92 地区电网数据采集与监控系统通用技术条件第 2 页共8 页3 作业准备3.1 作业任务3.2 准备工作安排第 3 页共8 页3.3 人员要求3.4 工器具3.5 材料准备第 4 页共8 页3.6 危险点分析及预控措施4 作业程序及作业标准4.1 开工第 5 页共8 页4.2 作业内容和工艺标准第 6 页共8 页5 竣工6 验收记录第7 页共8 页7 作业指导书执行情况评估8 注:定期维护报告因需审核,及按设备单元归档,另外存放。
第8 页共8 页。
光伏电站光伏并网逆变器检修规程

光伏电站光伏并网逆变器检修规程1. 范围本标准规定光伏并网逆变器设备的维护检修的基本内容;本标准适用于光伏电站光伏并网逆变器检修维护。
2. 规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。
凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准,凡是不注日期的引用文件,其最新版本适用于本标准。
3. 设备规范3.1 光伏并网逆变器形式及主要参数3.1.1 光伏并网逆变器形式为三相户内式光伏并网逆变器;3.1.2 光伏并网逆变器性能参数;表 2-1 北京意科 500kW 逆变器技术参数设备名称并网逆变器型号YGI-T500KTL输入数据最大直流输入功率550kWp直流输入电压范围MPPT(UDC)500Vdc~820Vdc 最大直流输入电压(UDC.max)880V最大直流输入电流(IDC.max)1100A输出数据额定交流功率500kW电网工作电压范围(UAC)270Vrms±10%电网频率50Hz总电流波形畸变率<3%功率因数>0.99最大效率98.5%功率损耗待机功耗(夜晚)<100W防护等级及环境条件符合 EN 60529 国际防护等IP20级标准允许环境温度(T)-20℃- +40℃相对湿度,不冷凝15%-93%最高海拔(高于海平面)2000 米表 2-2 阳光电源 500kW 逆变器技术参数输入最大输入功率560KW最大输入电压1000V启动电压500V最小工作电压460V最大输入电流1220AMPPT电压范围460~850VMPPT数量 1输入连接端数8/16输出额定输出功率500KW最大输出视在功率550KVA最大输出电流1008A总电流波形畸变率<3%(额定功率)额定电网电压315V电网电压范围252~362V额定电网频率50/60Hz电网频率范围47~52 Hz/57~62 Hz 功率因素范围0.9超前~0.9滞后隔离变压器无直流分量<0.5%额定输出电流效率最大效率98.7%欧洲效率98.5%保护输入侧断路设备直流负荷开关输出侧断路设备交流负荷开关直流过压保护具备交流过压保护具备电网监测具备接地故障监测具备过热保护具备绝缘监测具备常规数据尺寸(宽×高×深)1606×2034×860mm 重量1250kg工作温度范围-30~+55℃夜间自耗电<20W外部辅助电源电压380V,3A冷却方式温控强制风冷防护等级IP21相对湿度0~95%无冷凝最高海拔6000m(>3000m降额)排风需求量4500m3/h显示彩色触摸屏通讯RS485/Modbus,以太网3.2 逆变器工作性能3.2.1 光伏并网逆变器使用的环境条件环境温度:户内型为-20℃~+40℃;相对湿度≤93%,无凝露;无剧烈震动冲击, 垂直倾斜度≤50;工作环境应无导电爆炸尘埃, 应无腐蚀金属和破坏绝缘的气体和蒸汽;3.2.2 光伏并网逆变器正常使用的电网条件光伏并网逆变器应在下列电网条件下正常运行:1)电压总谐波畸变率小于 3%的公用电网;2)35kV 及以上正、负电压偏差的绝对值之和不超过标称电压 10%的电网电压;20kV 及以下三相电压的允许偏差为额定电压的±7%电网电压;3)频率允许偏差值在 49.5Hz~50.5Hz 的电网。
光伏逆变器控制器的检修维护

光伏逆变器控制器的检修维护.光伏控制器的各项性能检验测试,一般都是依据GB/T 19064—2003《家用太阳能光伏电源系统技术条件和试验方法》、GB/T 2423.1—2008《电子电工产品环境试验第2部分:试验方法试验A:低温》、GB/T 2423.2—2008《电子电工产品环境试验第2部分:试验方法试验B:高温》和GB/T 2423.3—2006《电子电工产品环境试验第2部分:试验方法试验cab:恒定湿热方法》等中的要求和方法进行。
了解和掌握光伏控制器检测测试的一些内容和方法,在光伏控制器的选型、应用及质量辨别与控制等方面都有积极作用。
1.主要测试仪器和检验设备1)数字多用表:要求电压、电流误差≤0.5%。
2)高低温试验箱:温度精度范围±0.2%以内。
3)高低温潮热试验箱:温度精度范围±2%以内,相对湿度精度范围±3%以内。
4)直流稳压电源:直流输出电压为0~100V,直流输出电流为0~30A。
5)滑动变阻器:可变电阻范围为0~150Ω。
6)电磁振动台。
2.检验测试内容及方法1)外观及文件资料的检查。
①目视检测设备外观以及主要零部件是否有损坏;元器件是否有松动或丢失;机壳面板是否平整,表面镀层是否牢固,漆面应均匀,无剥落、锈蚀及裂痕;各种开关是否便于操作,灵活可靠。
②目视检测标签内容是否准确、规范,各种功能开关和指示、显示的图标和文字说明是否清晰、正确,太阳电池、蓄电池及负载的接入点和正负极性是否标明。
③检查设备的使用说明书、检查合格证等文件资料是否齐全,附带的备用熔丝等配件是否符合装箱单的规格要求和数量。
2)充满断开和恢复控制电压起控点检测。
①开关型控制器:具有充满断开和恢复连接功能的控制器。
对于这类接通/断开式控制器,用其控制设计标准值12V的蓄电池时,其充满断开和恢复连接的工作起控点电压参考值如下:启动型铅酸蓄电池充满断开:15.0~15.2V;恢复:13.7V。
SUN2000逆变器现场问题处理指导-SolarwithHuawei

SUN2000逆变器现场问题处理指导ID原因ID103DC 输入电压高1 BoostA 输入电压高1.万用表检查直流输入组串电压是否正常(任何情况下<1000V )2.请检查光伏阵列组串1、2的串联配置及接线,保证开路电压不高于逆变器最大输入端电压,否则可能损坏逆变器。
2 BoostB 输入电压高1.万用表检查直流输入组串电压是否正常(任何情况下<1000V )2.请检查光伏阵列组串3、4的串联配置及接线,保证开路电压不高于逆变器最大输入端电压,否则可能损坏逆变器。
3 BoostC 输入电压高1.万用表检查直流输入组串电压是否正常(任何情况下<1000V )2.请检查光伏阵列组串5、6的串联配置及接线,保证开路电压不高于逆变器最大输入端电压,否则可能损坏逆变器。
106~113 组串1~8异常 1组串1~8功率输出异常1.通过 LCD 显示或手机 APP 显示检查该路组串电流是否明显低于其它组串电流;2.如果检查结果该路组串电流明显低于其它组串,请检查该路组串是否存在遮挡情况;3.如果检查结果该路组串表面清洁且无遮挡,请检查该路电池板是否损坏或其配置是否与其它组串不同;4.如果以上均无异常请排查是否为逆变器采样问题,首先逆变器未并网状态下查看组串电流显示是否存在明显异常;如有异常判为机器采样问题,建议尝试更换整机后观察三天运行情况。
5.以上若均无发现异常,请联系华为工程师。
120~127 组串1~8反向 1组串反接1.请检查逆变器对应的输入组串是否反接,如果是,请调整组串极性;2.如果未发现组串反接,请检查逆变器采样是否有问题:可先查看确认LCD 或手机APP 显示分析组串电流是否有异常,如果判断显示与实际差异超过2A (注意钳流表精度,防止误判)建议尝试更换整机后观察三天运行情况。
注意:如果确认反接,禁止在白天拔逆变器侧直流端子或操作直流开关,建议晚上无光照下进行整改操作。
2组串电流反灌1.请检查对应输入组串是否串联电池板个数比同路MPPT 输入的另一组组串少,如果是,请调整该组串串联电池板个数与同路MPPT 输入的另一组组串电池板个数一致;2.检查确认现场电池组串是否有存在遮挡、电池组件受损等异常情况;2.如果未发现组串反接等异常,请检查逆变器采样是否有问题:可先查看确认LCD 或手机APP 显示分析组串电流是否有异常,如果判断显示与实际差异超过2A (注意钳流表精度,防止误判)且确认外部直流输入无异常后建议尝试更换整机后观察三天运行情况。
光伏电站中逆变器日常维护、检修操作步骤及注意事项

光伏电站中逆变器日常维护、检修操作步骤及注意事项标题:深度剖析光伏电站中逆变器的日常维护、检修操作步骤及注意事项在当今社会,随着环保意识的日益增强和可再生能源产业的蓬勃发展,光伏发电逐渐成为人们关注的热点。
光伏电站作为光伏发电系统的核心设施,其逆变器作为电能转换的关键设备,受到了广泛的关注。
为了确保光伏电站的正常运行和发电效率,日常维护、检修操作的重要性愈发凸显。
下面,我将结合自身的经验和对光伏电站逆变器的理解,为你详细介绍光伏电站中逆变器的日常维护、检修操作步骤及注意事项。
1. 光伏电站中逆变器的日常维护光伏电站的逆变器是将太阳能板所产生的直流电转化为交流电的重要设备,其日常维护工作至关重要。
在日常维护中,需要注意以下几点:1.1 清洁:定期对逆变器进行清洁,确保其散热良好。
在清洁过程中,应当注意轻拍设备外表面,避免损坏设备。
1.2 检查:定期检查逆变器的接线端子和线路,确保连接牢固,避免接触不良而引起的温升过高等故障。
1.3 参数监控:定期对逆变器的关键参数进行监控和记录,例如电流、电压等数据,及时发现异常并进行处理。
2. 光伏电站中逆变器的检修操作步骤尽管日常维护可以减少逆变器的故障率,但在实际运行过程中,逆变器仍然存在一定的故障概率。
对于逆变器的检修操作步骤显得尤为重要。
一般而言,逆变器检修的步骤包括以下几个方面:2.1 故障诊断:需要进行故障诊断,通过观察、测量等手段找出故障原因。
2.2 隔离操作:在确认故障原因后,需要进行隔离操作,降低安全风险,确保检修人员的安全。
2.3 更换维修:依据故障的具体原因,进行更换维修等操作,恢复逆变器的正常运行。
3. 注意事项在进行光伏电站中逆变器的日常维护和检修操作时,需要特别注意以下几点:3.1 安全第一:在进行日常维护和检修操作时,安全永远是第一位的。
确保操作人员具备相关的安全意识和技能,穿着相关的防护装备,切勿擅自进行操作。
3.2 电气知识:操作人员需要具备一定的电气知识,了解逆变器的基本原理和工作机理,避免因为操作不慎导致的意外事故。
(完整版)阳光逆变器告警处理方案

接触器故障
温度异常
告警运行
环境温度超过55℃
1.检查逆变器室散热是否正常。2.检查直流柜下部环境温度探头是否运行正常
硬件故障
自动脱开电网,直流断路器脱扣
若交直流电压正常,设备未启动,应检查转接板是否正常工作
母线过压
测点位于直流电容
母线欠压
测点位于直流电容
主风机故障
自动脱开电网
IGBT模块风扇停止运行
线电压>362
(范围315v-362v)
等待电网电压恢复正常
交流欠压
自动脱开电网,直流断路器脱扣
线电压<250(范围250电网,直流断路器脱扣
F<48Hz(范围47 Hz -49.5 Hz)
等待电网电压恢复正常
频率过频
自动脱开电网,直流断路器脱扣
F>50.2Hz(范围50.2Hz-52Hz)
告警名称
运行状态
故障描述
处理方法
传感器失效
停机
IGBT模块下部交流传感器采集电流发生异常
目前会报三相电流不平衡,处理方法参考三相电流不平衡
PDP保护(内部保护)
停机
IGBT模块故障
检查模块是否运行正常,检查采样板是否运行正常,检查DSP、转接板是否运行
模块过温
停机
壳体温度限值108℃
检查IGBT轴流风机散热系统是否运行正常
检查IGBT模块风扇是否工作正常,风扇电源是否正常,风扇的信号节点是否松动脱落
直流熔断器故障
自动脱开电网,直流断路器脱扣
直流熔断器熔断(1250A)
1.直流侧是否由短路接地处
2.检查直流熔断器上测点是否松动
直流过流
自动脱开电网
(完整版)阳光逆变器告警处理方案.doc

告警名称运行状态传感器失效停机PDP 保护(内部停机保护)模块过温停机电抗器过温停机漏电流保护告警运行过载保护直流过压自动脱开电网,直流断路器脱扣直流欠压交流过压自动脱开电网,直流断路器脱扣交流欠压自动脱开电网,直流断路器脱扣频率欠频自动脱开电网,直流断路器脱扣频率过频自动脱开电网,直流断路器脱扣接触器故障温度异常告警运行硬件故障自动脱开电网,直流断路器脱扣故障描述处理方法IGBT模块下部交目前会报三相电流传感器采集电流不平衡,处理流发生异常方法参考三相电流不平衡IGBT模块故障检查模块是否运行正常,检查采样板是否运行正常 ,检查 DSP、转接板是否运行壳体温度限值检查 IGBT 轴流108℃风机散热系统是否运行正常温度限值 85℃检查柜顶风扇散热系统是否运行正常交流柜下部漏电检查传感器是否流传感器,限值接线良好,检查5A 接地铜牌上连接的各部件漏电流情况Udc> 1000 停运部分汇流箱,待整体负荷降低后再投运线电压> 362 等待电网电压恢(范围复正常315v-362v )线电压< 250(范等待电网电压恢围250v-315v )复正常F< 48Hz(范围 47 等待电网电压恢Hz -49.5 Hz) 复正常F > 50.2Hz( 范围等待电网电压恢50.2 Hz -52 Hz) 复正常环境温度超过 1.检查逆变器室55℃散热是否正常。
2.检查直流柜下部环境温度探头是否运行正常若交直流电压正常,设备未启动,应检查转接板是否正常工作母线过压测点位于直流电容母线欠压测点位于直流电容主风机故障自动脱开电网IGBT模块风扇停检查 IGBT 模块止运行风扇是否工作正常,风扇电源是否正常,风扇的信号节点是否松动脱落直流熔断器故障自动脱开电网,直流熔断器熔断 1. 直流侧是否直流断路器脱扣( 1250A)由短路接地处2. 检查直流熔断器上测点是否松动直流过流自动脱开电网直流侧发生短路检查直流侧电缆交流过流自动脱开电网,Iout > 1.25Ie(额 1 低功率运行直流断路器脱扣定电流) 2 检查交流侧 CT及采样板工作是否正常直流缓启故障自动脱开电网直流缓启回路存检查更换转接板在问题直流分量故障告警运行在交流侧检测出检查采样板,检直流电,查模块是否工作正常控制柜温度故障告警运行该传感器位于电 1. 电网谐波较抗器周围大引起设备过热2. 柜顶风扇运行异常采样故障自动脱开电网PV 极性接反自动脱开电网直流支路存在正逐一测量直流支负极接反现象路检查是否存在正负极反接的情况控制电源异常自动脱开电网控制电源失电 1. 控制电源跳闸2. 控制电源上级电源模块失电交流电流不平衡自动脱开电网交流电三相电流检查交流电流互部平衡感器,检查采样内外供电装态显示供电模式,本站设备为内供电交流开关状态显示交流开关分合状态板1若交流开关显示在分位,逆变器正常运行,检查交流断路器二次端子是否松动2若交流开关显示在分位,逆变器停止运行,应检查断路器跳闸原因交流主接触器状态交流防雷器故障自动脱开电网控制柜下部防雷 1 防雷器是否烧告警器故障毁2 防雷熔断器是否熔断3 防雷器及防雷熔断器传感线是否松动4 采样板是否运行正常支路空开异常告警运行直流支路空开断检查该支路是否开断开温度异常告警告警运行环境温度超过55℃,该测点位于直流柜绝缘阻抗低告警运行交直流电缆存在分别对交直流电绝缘阻值低的情缆测量绝缘值,况检查组件光伏线有无接地情况LVRT运行告警运行至自动低电压穿越(电待电网自动恢复脱开电网网电压突降,逆变器在一定范围内持续运行)CT 不平衡告警自动脱开电网交流侧三相电流 1 查交流侧 CT是不平衡否运行正常, 2采样板是否运行正常直流传感器异常停机直流侧支路空开检测直流支路及报的话,设备告直流母线是否正警运行。
阳光电源组串式逆变器安装和操作手册说明书

Building 7, No.333 Wanfang Rd, Minhang District, Shanghai, China. 2011122.1 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2 Explanations of Symbols . . . . . . . . . . . . . . . . . . . . . . . .3.Installation . . . . . . . . . . . . . . . . . . . . . . . . .3.1 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.2 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.3 Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . .3.4 Installation On-grid PV Inverter . . . . . . . . . . . . . . . . . . . . .3.5 Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . .3.5.1 PV Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5.2 Grid Connection . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5.3 Communication Connection (WIFI / Ethernet / GPRS / RS485) . . . . .4.Operation . . . . . . . . . . . . . . . . . . . . . . . . . .4.1 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.2 Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.3 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.3.1 Startup Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . .missioning . . . . . . . . . . . . . . . . . . . . . . .6.Shut Down & Restart the Inverter . . . . . . . . . . . . .6.1 Shut Down Procedures . . . . . . . . . . . . . . . . . . . . . . . . .6.2 Restart the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . .7.Maintenance&Trouble Shooting . . . . . . . . . . . . . .7.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.2 Fault Code and Trouble Shooting . . . . . . . . . . . . . . . . . . .8.Specifications . . . . . . . . . . . . . . . . . . . . . . . .17 18 18 1818 18 18 201.About This Manual1.1 Scope of Validity1.2 Target Group1.3 System DiagramThis manual describes the installation, commissioning, operation andmaintenance of the following on-grid PV inverters produced by Afore NewEnergy:This manual is for qualified personnel. The tasks described in this manual mustonly be performed by qualified personnel.Single-Phase(Two MPPT Trackers)HNS3000TL HNS3600TL HNS4000TL HNS5000TL HNS6000TLSingle-Phase(One MPPT Tracker)HNS3600TL-1Please keep this manual all the time available in case of emergency.About This Manual01The typical connection diagram for the entire PV system is on-grid.W I F I / RS 485Cloud serverPortal webPV Array Circuit Breaker3AC GridPV ArrayPV Inverter2.Safety & Symbols2.1 Safety Precautions1. All work on the inverter must be carried out by qualified electricians.2. The device may only be operated with PV panels.3. The PV panels and inverter must be connected to the ground.4. Do not touch the inverter cover until 5 minutes after disconnecting both DC and AC power supply. Safety & Symbols02Type Max AC Current [A]Rated current of AC breaker[A]Circuit Breaker and Surge Protector Recommendation: SPD: Lightning protection system, refer to the following options: AC side, nominal discharge current 20KA, second grade lightning protection,protection voltage 2.5KVDC side, nominal discharge current 20KA, second grade lightning protection,protection voltage 3.2KV The wiring distance between the inverter and the distribution box should be at least 5 meters.Single-Phase(Two MPPT Trackers)Single-Phase(One MPPT Tracker)HNS3600TL-11825Note:The Inverter can be only connected to low-voltage grid.(220/230Vac, 50/60Hz).5. Do not touch the inverter enclosure when operating, keep away from materials that may be affected by high temperatures.6. Please ensure that the used device and any relevant accessories are disposed of in accordance with applicable regulations.7. Afore inverter should be placed upwards and handled with care in delivery. Pay attention to waterproof. Do not expose the inverter to water, rain, snow or spray.8. Alternative uses, modifications to the inverter not recommended. The warranty can become void if the inverter was tampered with or if the installation is not in accordance with the relevant installation instructions.Afore inverter strictly comply with relevant safety standards. Please read andfollow all the instructions and cautions during installation, operation and maintenance.Safety & Symbols032.2 Explanations of SymbolsImportant NotesRead all instructions carefully. Failure to follow these instructions,3.Installation3.1 PackageUnpackingOn receiving the inverter, please check to make sure the packing and all components are not missing or damaged. Please contact your dealer directly for supports if there is any damage or missing components.Package List Open the package, please check the packing list shown as below.Installation 04Note: The HNS3600TL-1 is 1 pair of DC plug connector, theHNS3000-6000TL is 2 pairs.689101Overview of the Connection AreaThe following picture shows the assignment of the individual connection areas on the bottom of the inverter.Installation053.2 Product OverviewThe inverters are designed for indoor and outdoor installation (IP65), to increase the safety, performance and lifespan of the inverter, please selectthe mounting location carefully based on the following rules: The inverter should be installed on a solid surface, far from flammable or corrosion materials, where is suitable for inverter’s weight and dimensions. The ambient temperature should be within -25℃ ~ 60℃ (between -13 °F and140°F).The installation of inverter should be protected under shelter. Do not expose the inverter to direct sunlight, water, rain, snow, spray lightning, etc.Installation 063.3 Mounting LocationThe inverter should be installed vertically on the wall, or lean back on planewith a limited tilted angle. Please refer to below picture.Installation073.4 Installation On-grid PV Inverter Leave the enough space around inverter, easy for accessing to the inverter, connection points and maintenance.Step 2300mm500mm3.5 Electrical Connection3.5.1 PV ConnectionThe inverter is equipped with 2 MPPT channels, each of which contains a PVstring input. For best results, please ensure that each MPPT channel isconnected to a PV string separately. Otherwise, the inverter will activate voltageor automatic current protection.·The open-circuit voltage and short-circuit current of PV string must not exceed inverter’s range·The isolation resistance between PV string and ground must exceed 10 kΩ·The polarity from PV strings are correct·Use the DC plugs in the accessory·The lightning protector should be equipped between PV strings and inverter ·Disconnect all of the PV (DC) switch during wiringWarning:The fatal high voltage may on the DC side, please comply withelectric safety when connecting.Please make sure the cable connected in correct polarity withinverter, otherwise inverter could be damaged.Installation09Note :It is strongly recommended to connect by two strings of panels for models of two MPPT channels, e.g. HNS3000-6000TL.210 solar panels should connect from PV side A and B as the Y -shaped, setting PV model parallel and PV side voltage notexceed 500V one MPPT; other solar panels we are recommend you though dual MPPT input the cables, also no exceed 450VNote:Please use PV connector crimperNote:You’ll hear click sound whenthe connector assembly is correctNote:PV cable suggestion Cross-section 4 mmThe on-grid PV inverters work with grid (220/230/240 Vac, 50/60 Hz).The external AC switch should be installed between inverter and grid to isolate from grid. Please make sure below requirements are followed before connecting AC cable to the inverter.·The AC (grid) voltage must not exceed inverter’s range·The phase-line from AC distribution box are correctly connected ·Use the AC plugs in the accessory·The surge protector should be equipped between grid and inverter ·Disconnect the AC (grid) switch during wiringInstallation103.5.2 Grid ConnectionWarning:The fatal high voltage may on the AC side, please comply with electric safety when connecting.Please make sure the right line of AC grid connected with inverter, otherwise inverter could be damaged.AC line goes through AC terminal waterproof head and capNote:AC cable suggestion Cross-section4 mm11InstallationConnect AC line, Live line (L), Neutral line (N) and Ground Wire (PE) according to polarity.1. Connect AC terminals and waterproof head, tightenthe cap, make sure they clip closely together.2. Connect AC connector to AC terminal of the inverter.3. Afeer making sure that it is firmly insered, tightenthe sleeve on the AC connector to the right and hear aclick.12Installation3.5.3 Communication ConnectionThe monitoring module could transmit the data to the cloud server, and display the data on the PC, tablet and smart-phone.Install the WIFI / Ethernet / GPRS / RS485 CommunicationWIFI / Ethernet / GPRS / RS485 communication is applicable to the inverter. Please refer to "Communication Configuration Instruction" for detailedinstruction.Installation13For single-phase inverter, please follow below pin order RS485A(Pin 7) to single-phase meter (Pin 24)RS485B(Pin 8) to single-phase meter (Pin 25)4.5 Zero-injection Smart Meter (Optional)Smart meter is an intelligent control equipment which is used for on-grid inverters. Its main function is to measure the forward and reverse power on Note:Operation14Note:The Inverter could be connected in parallel with Smart Meter,make sure the total load power not exceed Smart Mater’s limitation.GridPV InverterPV ArrayPV ArrayPV ArrayNote:Please refer to "Zero InjectionSmart Meter Installation andOperation Manual" for detailed instruction.Operation155.2 Menu StructureSecond Level MenuOperation175.3.3 Frequency RangeMain MenuENTENTENTENTENTENTENTENTNote:The parameters setting only works after the inverter is restarted.ENTENTENTENTENTENTUP/DOWNUP/DOWNUP/DOWNUP/DOWN set protection timeUP/DOWN set level 2UP/DOWNUP/DOWNUP/DOWNUP/DOWN set level 1UP/DOWN set level 2UP/DOWN set level 1UP/DOWNUP/DOWN set protection timeUP/DOWN set level 2UP/DOWNUP/DOWNUP/DOWNUP/DOWN set level 1UP/DOWN set level 2UP/DOWN set level 120Maintenance&Trouble Shooting Trouble-Shooting ListOperation165.3.1 Startup5.3 SettingExplanation of LCD Display Content5.3.2 Voltage RangeMain MenuENTENTUP/DOWNUP/DOWNENTENTUP/DOWN Adjust the time andUP/DOWNCommissioning18Before starting up commissioning at site, please make sure below procedures and requirements are fully meet.• Mounting location is meet the requirements.• All of the electrical wiring is firmly connected, including PV wiring, Grid wiring and Earth wiring.• The inverter setting has been finished accordingly to local standards or regulations.Commissioning Procedures• Turn on the AC switch between inverter output and the public grid;• Turn on the DC switch on the inverter;• Turn on the PV switch of the system.6. Commissioning7. Shut down & restart inverter• Turn off the DC switch on the inverter.• Turn off the DC switch between PV panels and the inverter (if any).• Close the AC switch between the inverter and the public grid.• Shut down the inverter according to Chapter 7.1.• Start-up the inverter according to Chapter 6.7.2 Restart7.1 Shut downNote:The inverter will be operable after minimum 5 minutes.5.Operation 5.1 Control Panel○2○3○1○○45○○○678Operation 15Shut Down & Restart the Inverter19Periodically maintenance are necessary, please follow steps as below. PV connection: twice a yearAC connection : twice a yearEarth connection: twice a yearHeat sink: clean with dry towel once a year.Fault messages will be displayed when fault occurs, please according to trouble- shooting table find related solutions.8. Maintenance&Trouble Shooting8.1 Maintenance8.2 Trouble Shooting21 Maintenance&Trouble Shooting22Maintenance&Trouble Shooting8.Specifications Specifications23Max. DC Power ( W )Max. DC Voltage ( V )MPPT Voltage Range ( V ) MPPT Full Power Voltage Range ( V ) Rated Input Voltage ( V )Start-up Voltage ( V )Max. Input Current ( A )Max. Short Current ( A )No. of MPP Tracker /No. of PV StringInput Connector TypeMax. Output Power ( W ) Nominal Output Power ( W ) Max. Output Current ( A ) Nominal Output Voltage ( V )Grid Voltage Range Nominal Output Frequency ( Hz ) Grid Frequency Range Output Power FactorOutput Current THDMax. EfficiencyEuro Efficiency°C180Vac-276Vac (According to local standard)45~55Hz/54~66Hz (According to local standard)1 default (adjustable from 0.8 leading to 0.8 lagging)L/N/PE, 220Vac, 230Vac, 240VacIntegrated(Type III)RS485 / WiFi / Wire Ethernet / GPRS (op ti onal)EN/IEC 61000-6-2, EN/IEC 61000-6-3, EN61000-3-2, EN61000-3-3, EN61000-3-11, EN61000-3-12IEC 60068, IEEE1547,EN62109PV Reverse Polarity Protection PV Insulation Resistance Detection AC Short Circuit ProtectionAC Over Current ProtectionAC Over Voltage ProtectionAnti-Islanding Protection Residual Current Detection Over Temperature Protection Integrated DC switchSurge ProtectionDimensions (W x H x D, mm) Weight ( kg )Protection Degree Enclosure MaterialAmbient Temperature Range ( ) Humidity RangeTopology Communication Interface Cooling ConceptNoise Emission ( db )Night Power Consumption ( W ) Max. Operation Altitude ( m )EMC StandardSafety StandardGrid-connec ti on3607014 x 218 x 22/2330030001598.20%97.80%YESYESYESYESYESYESYES450060070-550110-550MC43607014 x 218 x 22/23960360017.598.20%97.82%YESYESYESYESYESYESYES4000540060070-550130-550MC43607014 x 218 x 22/2440040002098.20%97.85%YESYESYESYESYESYESYES10<28358×360×142600060070-550145-550MC43607014 x 218 x 22/25500500024<3%50/6098.20%97.90%YESYESYESYESYESYESYESConvection<1IP65AluminumTransformerless0-100%700060070-550180-550MC43607014 x 218 x 22/26600600028.798.20%97.92%YESYESYESYESYESYESYES840060070-550220-550MC4YES YES YES YES YESYES YES YES YES YES 3960360017.598.20%97.80%3607014181/1420060070-500130-500MC4YESYESYESYESYESYESYESYESYES-25 ~ +60°C (Derating 45°C)EN50549-1, EN50438, RD 1699,UNE 217001, RD 413, IEC61727, IEC62116, IEC61683, VDE4105, UL1741 VDE0126 AS4777.2 NB/T 32004-2018, UNT C 15-712-1, ABNT NBR 16149, ABNT NBR 16150。
05年款阳光维修手册

设施设定
道路编辑
已注册道路
画面模式设置
电话号码设定 设置查询条件
双画面设置
道路设定
道路全程显示
各种设置
最新目的地设定 道路删除
光伏逆变器维修知识

光伏逆变器维修知识光伏逆变器是太阳能发电系统中的重要组成部分,主要负责将太阳能板所产生的直流电转换为交流电,以供电网使用或储存。
然而,由于各种原因,光伏逆变器在运行过程中可能会出现故障,需要进行维修。
本文将介绍一些常见的光伏逆变器故障及其维修方法。
1. 逆变器无输出如果光伏逆变器无输出,首先要检查太阳能板的连接是否正常,是否有损坏或松动的电缆。
同时,也需要检查逆变器的输入电压是否正常,是否存在过高或过低的情况。
若以上都正常,可能是逆变器内部故障,需要进行更深入的维修。
2. 逆变器输出电压异常如果光伏逆变器的输出电压不稳定或超过正常范围,可能是电压传感器损坏或校准不准确所致。
此时,可以尝试重新校准电压传感器,或更换新的传感器。
3. 逆变器过热光伏逆变器在长时间运行过程中可能会过热,导致系统停机或损坏。
此时,应检查逆变器周围的环境温度是否过高,是否有足够的通风设施。
如果环境温度正常,可能是逆变器内部散热系统故障,需要清洁或更换散热器。
4. 逆变器频繁断电重启如果光伏逆变器频繁断电重启,可能是由于电网故障或短路引起的保护机制触发。
此时,需要检查电网连接是否正常,是否有短路或漏电的情况。
如果电网连接正常,可能是逆变器内部电路故障,需要修复或更换电路板。
5. 逆变器显示异常有些光伏逆变器配备了显示屏,用于显示运行状态和故障信息。
如果显示屏显示异常或无法正常显示,可能是屏幕损坏或与主控板连接故障。
此时,可以尝试重新连接或更换显示屏。
维修光伏逆变器需要一定的专业知识和技能,如果遇到复杂的故障或无法自行解决,建议寻求专业技术人员的帮助。
同时,定期进行光伏逆变器的维护保养也是非常重要的,可以延长其使用寿命并提高发电效率。
维护保养包括清洁逆变器表面、检查连接线路、定期校准传感器等。
光伏逆变器作为太阳能发电系统的核心设备,其正常运行对于发电效率和系统稳定性至关重要。
因此,对于常见的光伏逆变器故障要有一定的了解,并掌握相应的维修方法,以保证系统的可靠运行。
光伏发电逆变器故障诊断与检修技术

光伏发电逆变器故障诊断与检修技术随着科技的不断发展,光伏发电逆变器现已广泛应用于各个领域。
如今,它已不再只是一个新颖的实验性产品,而是一项成熟的技术。
然而,光伏发电逆变器也不是万无一失的。
在使用过程中,还是会出现各种各样的故障。
因此,如何进行光伏发电逆变器故障诊断与检修技术的研发和推广,显得尤为重要。
一、背景介绍光伏发电逆变器,是将直流电转换成交流电的设备。
它是太阳能电池发电系统的核心部分,负责将太阳光转化为可供电设备使用的电能。
由于其重要性,光伏发电逆变器的质量必须得到保证。
否则,一旦发生故障,就会给人们的生产和生活带来不小的影响。
所以,除了日常维护外,光伏发电逆变器的故障诊断和检修显得格外重要。
二、故障诊断光伏发电逆变器故障诊断,是对逆变器故障进行定位和分析的过程,其目的是及时准确地找出故障的源头,以便采取有效措施进行修复。
在故障诊断中,通常采取以下措施:1. 明确故障现象:如逆变器的输出功率异常,电压不稳定等。
2. 检查逆变器本身:如检查逆变器的各项参数、温度、电压等。
3. 检查配件和连接线路:如检查光伏电池板、电缆连接头、地线等。
4. 检查电力设备:如检查逆变器压变、接触器等。
5. 进行相关测试:如进行开路电压测试、短路电流测试等。
通过以上各项措施相互配合,就可以很快地找出光伏发电逆变器故障的根源。
当然,在故障诊断过程中,还需要依据自身的情况来进行具体操作。
三、检修技术一旦确定了光伏发电逆变器的故障,就必须采取相应的检修技术进行排除。
光伏发电逆变器的检修技术主要包括以下几个方面:1. 检查逆变器本身:在进行实际操作之前,必须首先对逆变器进行检查,确定故障的范围和性质。
2. 更换配件:如更换故障的光伏电池板、电缆连接头、地线等。
3. 更换电力设备:如更换逆变器压变、接触器等。
4. 更换电源:如更换光伏电池组和蓄电池等。
在实际操作中,应该根据不同的故障类型采取不同的检修技术。
四、结论光伏发电逆变器是现代能源技术的一项重要发明。
光伏逆变器的常见故障及维修方法

光伏逆变器的常见故障及维修方法
光伏逆变器要是出问题了可真让人头疼啊!那咱就说说常见故障和维修方法。
要是逆变器不工作了,这可咋办?嘿,有可能是电源问题呀。
就像汽车没油了跑不动一样,逆变器没了电也没法干活。
检查下电源线有没有插好,插座是不是有电。
要是显示故障代码,那可就像收到了神秘信号,得赶紧查查说明书,看看是啥问题。
也许是温度过高了,这时候就像人发烧了一样,得让它降降温。
维修的时候可得小心啊!这可不是闹着玩的。
万一不小心触电了,那可就惨了。
所以一定要先断电,这就像打仗前要做好防护一样。
维修过程中要仔细,别毛手毛脚的。
光伏逆变器的应用场景可多了去了。
在屋顶上装着,把太阳能变成电能,多棒啊!就像一个小魔法师,把阳光变成宝贝。
它的优势就是环保又节能,还能给自己家省电费呢。
比如说我邻居家就装了光伏逆变器,那效果杠杠的。
家里的电大部分都能自己供应,省了不少钱呢。
这就像有了个小金库,随时都能拿出宝贝来。
光伏逆变器真是个好东西,虽然有时候会出点小毛病,但只要咱小心
维修,就能让它继续发挥大作用。
大家都赶紧用起来吧!。
太阳能光伏逆变器维修手册

太阳能光伏逆变器维修手册
太阳能光伏逆变器是太阳能发电系统中的重要组件,其主要功能是
将太阳能电池板所产生的直流电转换为交流电以供家庭或工业用电。
在日常使用中,由于各种原因,光伏逆变器有可能会出现故障,因此
及时有效的维修至关重要。
本手册将介绍太阳能光伏逆变器的常见故
障及相应的维修方法,希望对使用者在遇到问题时能提供一定的帮助。
一、光伏逆变器无电输出
1. 检查光伏逆变器的输入端是否连接正常,电缆是否破损或松动。
2. 检查太阳能电池板是否正常发电,是否有阴影覆盖导致光照不足。
3. 检查逆变器内部是否存在故障,如变压器或电路板损坏。
二、光伏逆变器输出电压波动大
1. 检查光伏逆变器的输出端连接是否紧固,电缆是否受潮或老化。
2. 检查逆变器内部电容器是否损坏,导致电压波动过大。
3. 调节逆变器的输出电压参数,使其处于正常范围内。
三、光伏逆变器发出异常噪音
1. 检查逆变器内部风扇是否受阻,需要清洁或更换。
2. 检查逆变器的输出变压器是否存在问题,可能需要重新固定或更换。
四、光伏逆变器无法启动
1. 检查逆变器的开关是否正常,是否接通电源。
2. 检查逆变器内部是否存在故障,如电路板烧坏或元件损坏。
以上是太阳能光伏逆变器常见故障及维修方法的介绍,使用者在遇到问题时可根据实际情况进行排查和处理。
如若遇到复杂故障或无法解决,建议及时联系厂家或专业维修人员进行处理,以确保太阳能发电系统的正常运行,提高发电效率,保障用电安全。
希望本手册能为广大太阳能光伏逆变器用户提供一定的参考价值。
华为太阳能逆变器SUN2000维修条件说明书

HUAWEI SUN2000 Inverter Service Conditions For French Polynesia and NewCaledoniaHuawei Technologies (New Zealand) Company LimitedHuawei Solar InverterLimited Product Support Service ConditionsThese service conditions apply to the following products:➢SUN2000-3/5/6 KTL-L1➢SUN2000-5/6/10KTL-M1➢SUN 2000-100KTL-M1➢SUN2000-8/10/12/15/17/20KTL-M2➢SUN2000-115KTL-M2➢SUN2000-29.9/30/36/40/50KTL –M3➢SUN2000-450/600W-P➢SUN2000-450W-P2➢Smart Dongle, Smartlogger and Smart ACU➢Smart Power Sensor➢LUNA2000-5/10/15-S0➢Backup Box-B0/B1The service conditions described in this document are subject to any rights you may have under local consumer laws.Service Conditions:Huawei provides remote support for solar inverter➢Remote SupportRemote Support means Huawei provides solutions for technical enquiries or problems relating to the solar inverter products under warranty by telephone or e-mail. It includes Help Desk, Remote Technical support and Online Technical Support (https:///services/).•Remote Technical Support provides technical support to Huawei’s customers for solar inverter products, these includes technical enquiry, problem handling, and firmware update.The technical enquiry service provides consultation services in respect of Huawei inverterproducts. And when we do the maintenance of the FusionSolar, Huawei may update orrestart your system. Email:******************************Disclaimer:➢All above mentioned service support apply only to SUN2000 Series Products, Smart PV Optimizer, Smart Power Sensor, Smart Dongle, SmartLogger, SmartACU, and LUNA2000.➢Subject to any rights you may have under local consumer laws, accessories and consumable parts, including but not limited to cables and connectors, are not covered by the services set out above.➢Support services shall not apply in the following circumstances:•Damage as a result of force majeure (including but not limited to natural disasters, fires and war).•Damage as a result of natural wear and tear.•Direct damage caused by failure to meet system requirements provided in writing including site running environment or external electricity parameters.•Damage from lightning due to unsuitable system design.•Damage to hardware or data due to customer’s negligence, inappropriate operation or intentional damage.•Damage caused by non-compliance with the operation manual of the equipment. •System damage caused by the customer or third parties, including relocation and installation of the system not in compliance with Huawei’s requirements or instructions.•Damage caused by adjustment, change or removal of identification marks not in compliance with Huawei requirements or instructions•System damage directly caused by problems in customer’s infrastructure.Huawei Service OrganizationHuawei has built up an extensive service organization world-wide. For service support for SUN2000 products, Huawei has defined a support organization to support the process as depicted below:Contact DetailsHuawei Technologies (New Zealand) Company LimitedLevel 23, The Huawei Centre, 120 Albert Street, Auckland, New ZealandE-mail: ******************************Web: https:///。
阳光电源组串式逆变器安装和操作手册.pdf_1700112686.9149146说明书

Version: 03.610100007100Building 7, No.333 Wanfang Rd, Minhang District, Shanghai, China. 2011121. About This Manual . . . . . . . . . . . . . . . . . . . . . . 1.1 Scope of Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2 Target Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.3 System Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2. Safety & Symbols . . . . . . . . . . . . . . . . . . . . . . . 2.1 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Explanations of Symbols . . . . . . . . . . . . . . . . . . . . . . . . .3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Pre-installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1.1 Unpacking & Package List . . . . . . . . . . . . . . . . . . . . . . .3.1.2 Exterior Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.1.3 Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . .3.2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. Electrical Connection. . . . . . . . . . . . . . . . . . . . .4.1 PV Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Grid Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Earth Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 Communication Connection . . . . . . . . . . . . . . . . . . . . . . .5. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.1 Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.2 Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.3 Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . .6. Commissioning . . . . . . . . . . . . . . . . . . . . . . .7. Start-up & Shut Down . . . . . . . . . . . . . . . . . . . . 7.1 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Shut down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8. Maintenance&Trouble Shooting . . . . . . . . . . . . . . . 8.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9. Specifications . . . . . . . . . . . . . . . . . . . . . . . .Contents222222232323232327Contents991114151818192020212111112234445781. About This Manual1.1 Scope of Validity1.2 Target Group1.3 System DiagramThis manual describes the installation, commissioning, operation andmaintenance of the following on-grid PV inverters produced by Afore NewEnergy:This manual is for qualified personnel. The tasks described in this manual must only be performed by qualified personnel.Single-Phase((Two MPPT Tracker)HNS7000TL HNS8000TL HNS9000TL HNS10000TL Please keep this manual stored carefully and accessible at any time.About This Manual01The typical connection diagram for the entire PV system is on-grid.W I F I / R S 485Cloud serverWebPV Inverter Circuit BreakerAC GridPV Array PV ArrayPV Array2. Safety & Symbols2.1 Safety Precautions1. All work on the inverter must be carried out by qualified electricians. And ensure that children cannot access to the inverter.2. The PV generator and inverter must be connected to the ground separately in order to reach maximum protection for property and persons.3. Do not touch cover until five minutes after disconnecting all sources of supply. This is because the charge stored in capacitors may result a risk of electric shock.4. The enclosure of Inverter can become hot during operation. To reduce the risk of injury, do not touch the cover, heat sink at the back of the PV-Inverter or nearby surfaces while Inverter is operating.Safety & Symbols 02Circuit Breaker and Surge Protector Recommendation:Note:The Inverter can be only connected to low-voltage grid.(220 / 230 / 240Vac,50 / 60Hz).SPD: Lightning protection system, refer to the following options:• AC side, nominal discharge current 20KA, second grade lightning protection, protection voltage AC 305V.• DC side, nominal discharge current 20KA, second grade lightning protection,protection voltage DC 600V.5. Do not use the inverter for other purposes which not described in this manual.6. Both the inverter and associated transport packaging are mainly made of recyclable raw materials. Please ensure that the used device and any relevant accessories are disposed of in accordance with applicable regulations.7. Packed with EPE foam and carton, the inverter should be placed upwards and handled with care in delivery. Pay attention to waterproof.8. Alternative uses, modifications to the inverter not recommended. The installation of components not authorized by Afore New Energy will void the warranty claims.Afore inverter strictly comply with relevant safety standards. Please read and follow all the instructions and cautions during installation, operation and maintenance.Safety & Symbols032.2 Explanations of Symbols3. Installation 3.1 Pre-installation Installation04 3.1.1 Unpacking & Package List789101615141311UnpackingOn receiving the inverter, please check to make sure the packing and all components are not missing or damaged. Please contact your dealer directly for supports if there is any damage or missing components.Package ListOpen the package, please check the packing list shown as below.Installation053.1.2 Exterior ObjectsHNS7000-8000TLHNS9000-10000TLInstallation 06Inverter TerminalsHNS9000-10000TLHNS7000-8000TLThe inverters are designed for indoor and outdoor installation (IP65), to increase the safety, performance and lifespan of the inverter, please selectthe mounting location carefully based on the following rules:• The inverter should be installed on a solid surface, far from flammable or corrosion materials, where is suitable for inverter’s weight and dimensions.• The ambient temperature should be within -25℃ ~ 60℃ (between -13 °F and 140°F).• The installation of inverter should be protected under shelter. Do not expose the inverter to direct sunlight, water, rain, snow, spray lightning, etc.Installation073.1.3 Mounting Location The inverter should be installed vertically on the wall, or lean back on plane with a limited tilted angle. Please refer to below picture.Installation 083.2 Mounting Keep enough space for sufficient heat dissipation, convenient operation and maintenance.300mm500mm4. Electrical Connection4.1 PV ConnectionHNS7000TL and HNS8000TL inverters have dual MPPT channels, channel A includes 1 PV string input, and channel B includes 2 PV string inputs. For the best results, please ensure that each pair of photovoltaic input terminals is connected to a photovoltaic string separately. Otherwise, the inverter will trigger the voltage or current protection automatically. Please make sure below requirements are followed:• The open-circuit voltage and short-circuit current of PV string should not exceed the reasonable range of the inverters.• The isolation resistance between PV string and ground must exceed 10 kΩ.• The polarity of PV strings are correct.• Use the DC plugs in the accessory.• The lightning protector should be equipped between PV string and inverter.• Disconnect all of the PV (DC) switch during wiring.Warning:The fatal high voltage may on the DC side, please comply withelectric safety when connecting.Please make sure the cable connected in correct polarity withinverter, otherwise inverter could be damaged.Electrical Connection10Note:PV cable sugges�on Cross-sec�on ≥4mm²Note:A "click" will be heard when the connectors are assembled correctly.The cable should be �ghtlyconnected by the crimping pliers.The on-grid PV inverters work with grid (220/230/240 Vac, 50/60 Hz).The external AC switch should be installed between inverter and grid to isolate from grid. Please make sure below requirements are followed before connecting AC cable to the inverter.• The AC (grid) voltage should not exceed the reasonable range of the inverters.• The phase-line from AC distribution box are correctly connected . • Use the AC plugs in the accessory.• The surge protector should be equipped between grid and inverter.• Disconnect the AC (grid) switch during wiring.Electrical Connection114.2 Grid ConnectionWarning:The fatal high voltage may on the AC side, please comply with electric safety when connecting.Please make sure the right line of AC grid connected with inverter,otherwise inverter could be damaged.Note:PV string sugges�on: HNS7000-8000TL connect 3 PV strings, HNS9000-10000TL connect 4 PV strings.Like picture shown below, pass the AC cable (cross section for 7-8kW ≥ 6mm²(copper) / 9-10kW≥10mm² (copper) or 16mm² (aluminum) ) through the junction box wth a stripped length of 10±0.5mm, use crimping pliers to crimp the stripped wire harness to the terminal, wrap the joint position with insulation tape.Electrical Connection 12Note:Unscrew the row of screws,insert the wire harness into the U,W,PE caps one by one, and tighten the screws.W=ACN=Neutral lineThe wiring terminals should be wrapped with insula�on tape, otherwise it will cause a short circuit and damage the inverter.Electrical Connection13Fix the junction box with the wiring cover screws in the accessories,and tighten the waterproof connector.Electrical Connection144.3 Earth ConnectionThe user must connect a protective earth (PE) terminal to prevent electric shock. And make sure this PE terminal is properly grounded.Note:copper cable or aluminum cable Cable diameter ≥ 6mm²Fix the yellow-green PE wire to the ground hole on the lower right side of theinverter with screws, make sure that the PE terminal is properly grounded.Electrical Connection15The monitoring module could transmit the data to the cloud server, and display the data on the PC, tablet and smart-phone.WIFI / Ethernet / GPRS / RS485 communication is applicable to the inverter. Please refer to "Communication Configuration Instruction" for detailed instruction.Install the WIFI / Ethernet / GPRS / RS485 Communication4.4 Communication ConnectionElectrical Connection16Zero-injection Smart Meter (Optional)Smart meter is an intelligent control equipment which is used for on-grid inverters. Its main function is to measure the forward and reverse power on the grid-connected side, and transmit data to the inverter through RS485 communication to ensure that the power of the inverter is less than or equal to the user's home load, and no current flows into the grid.Electrical Connection17Note:The Inverter could be connected in parallel with Smart Meter,make sure the total load power not exceed Smart Mater’s limitation.GridPV InverterOperation185. Operation5.1 Control Panel○2○3○1○○45○○○678Operation195.2 Menu StructureSecond Level MenuThird Level Menu5.3.1 Startup5.3 SettingExplanation of LCD Display ContentOperation20UP/DOWNUP/DOWN1s DelayENTOperation215.3.3 Frequency RangeMain MenuENTENTENTENTENTENTENTENT5.3.2 Voltage RangeMain MenuENTENTENTENTENTENTENTENTUP/DOWNUP/DOWNUP/DOWNUP/DOWN set protection timeUP/DOWN set level 2UP/DOWNUP/DOWNUP/DOWNUP/DOWN set level 1UP/DOWN UP/DOWN set level 1UP/DOWNUP/DOWNUP/DOWNUP/DOWN set protection timeUP/DOWN set level 2UP/DOWNUP/DOWNUP/DOWNUP/DOWN set level 1UP/DOWN UP/DOWN set level 1Commissioning22Before starting up commissioning at site, please make sure below procedures and requirements are fully meet.• Mounting location is meet the requirements.• All of the electrical wiring is firmly connected, including PV wiring, Grid wiring and Earth wiring.• The inverter setting has been finished accordingly to local standards or regulations.Commissioning Procedures• Turn on the AC switch between inverter output and the public grid; • Turn on the DC switch on the inverter;• Turn on the PV switch of the system.• Turn on the AC switch between the inverter and the public grid.• Turn on the DC switch between PV panels and the inverter (if any).• Turn on the DC switch on the inverter.Inverter will enter into standby mode, and the LCD screen lights up and show contents , and then complete the first setting of the inverter according to 5.3.1.The LED will be lighted up after the inverter enter into running states.Please check the following requirements before testing:• Installation location is suitable according to Chapter 3.1.3.• All electrical wires are connected tightly, including PV modules, AC side, Earth Line.• Inverters should be set according to the required local grid standard. • More information please contact with Afore or distributors.6. Commissioning7. Start-up & Shut Down7.1 Start-upStart-up & Shut Down23Periodically maintenance are necessary, please follow steps as below. PV connection: twice a year AC connection : twice a year Earth connection: twice a yearHeat sink: clean with dry towel once a year.Fault messages will be displayed when fault occurs, please according to trouble- shooting table find related solutions.• Turn off the DC switch on the inverter.• Turn off the DC switch between PV panels and the inverter (if any).• Close the AC switch between the inverter and the public grid.8. Maintenance&Trouble Shooting• Shut down the inverter according to Chapter 7.2.• Start-up the inverter according to Chapter 7.1.7.3 Restart8.1 Maintenance8.2 Trouble Shooting7.2 Shut downNote:The inverter will be operable after minimum 5 minutes.24Maintenance&Trouble Shooting Trouble-Shooting List25Maintenance&Trouble Shooting26 Maintenance&Trouble ShootingSpecifications279. SpecificationsMax. DC Power ( W )Max. DC Voltage ( V )MPPT Voltage Range ( V )MPPT Full Power Voltage Range ( V )Rated Input Voltage ( V )Start-up Voltage ( V )Max. Input Current ( A )Max. Short Current ( A )No. of MPP Tracker /No. of PV StringInput Connector TypeMax. Output Power ( W )Nominal Output Power ( W )Max. Output Current ( A )Nominal Output Voltage ( V )Grid Voltage Range Nominal Output Frequency ( Hz ) Grid Frequency Range Output Power Factor Output Current THDMax. EfficiencyEuro Efficiency°C180Vac-276Vac (According to local standard) 45-55Hz/54-66Hz (According to local standard)1 default (adjustable from 0.8 leading to 0.8 lagging)L/N/PE, 220Vac, 230Vac, 240VacInt egra t ed(T yp e III)RS485 / W iF i / W ire Et her n e t / GP RS (op�on a l)Dimensions (H x W x D, mm)W eigh t ( kg )Protec�on Degree Enclosure MaterialAmbient Temperature Range ( ) Humidity RangeT opo l o g yCommunica�on Interface Cooling ConceptNoise Emission ( d b )Night Power Consump�on ( W ) Max. Opera�on Al�tude ( m )E MC St a n dardS a f e ty St a n dardGri d-c onn ec�on<3%50/60Convec�onAlu m i n u m-25- +60Tra n s fo r m erless0-100%4000<40<1I P657700700033.698.20%97.95%1719510 x 370 x 167527 x 370 x 188 98001120014+2618+352/31260060070-550220-55036070MC41400026+2635+352/4880098.32%98.00%98.40%98.10%9900900045110001000050800038.398.20%98.00%EN/IEC 61000-6-2, EN/IEC 61000-6-3, EN61000-3-2, EN61000-3-3, EN61000-3-11, EN61000-3-12IEC 60068, UL1741, EN62109IEEE1547, CSA C22, EN50549, VDE4105, VDE0126, RD1699,ABNT NBR16149 & 16150, AS4777.2, NB/T32004, G98/G99, IEC61727Op�onalY ESPV Reverse Polarity Protec�on PV Insula�on Resistance Detec�on AC Short Circuit Protec�onAC Over Current Protec�onAC Over Voltage Protec�onAn�-Islanding Protec�on Residual Current Detec�on Over Temperature Protec�on Integrated DC switchSurge Protec�onSmart IV Curve ScaningQuick Arc Fault Circuit Interrup�on。
阳光电源SG110HX-CN光伏并网逆变器用户手册说明书

光伏并网逆变器
SG110HX-CN
SG110HX-CN 光伏并网逆变器用户手册SG110HX-
CN-UCN-Ver12–202307
SG110HX-CN-UCN-Ver12–202307
版权所有
版权所有©阳光电源股份有限公司 2023。保留所有权利。 本手册相关内容未经阳光电源股份有限公司(简称“阳光电源”)授权,不得私自扩散、复 制或转发给第三方,不得上传至公共网络等第三方平台。 商标
4 机械安装 ......................................................................................................... 15
4.1 安装注意事项 .............................................................................................. 15 4.2 选择安装地点 .............................................................................................. 15
V
4.5.1 支架安装 ........................................................................................... 22 4.5.2 挂墙安装 ........................................................................................... 23 4.6 安装逆变器 ................................................................................................. 24
新能源光伏发电企业逆变器检修及定期维护内容及要求

新能源光伏发电企业逆变器检修及定期维护内容及要求逆变器是新能源光伏发电系统中的关键设备,它将光伏电池板产生的直流电转换成交流电,供电给家庭、企业或电网使用。
为了确保逆变器的正常运行和发电效率,进行逆变器的检修和定期维护是非常重要的。
1.逆变器检修内容(1)外观检查:检查逆变器外壳是否有损坏、变形或脱落的情况,检查连接部分是否有松动、氧化或烧伤的现象。
(2)线路检查:检查逆变器的接线端子是否紧固可靠,线路是否正常连接,是否有短路、断路、接地等问题。
(3)散热检查:检查逆变器的散热器是否清洁,散热风扇是否正常工作,散热片是否有积尘和阻塞的情况。
(4)参数检查:检查逆变器的参数设置是否与设计要求一致,如并网电压、频率设置,功率输出范围等。
(5)设备测试:根据检查结果,对逆变器进行电气参数测试,检查其运行状态是否正常,输出电压、电流是否稳定。
2.逆变器定期维护内容(1)清洁:定期清洁逆变器的外壳和散热器,防止灰尘或杂物堆积影响散热效果。
(2)检查:定期检查逆变器的接线端子,确保其紧固可靠,防止接触不良造成电阻。
(3)散热:定期检查逆变器的散热器和风扇,确保其正常工作,防止过热导致电路损坏。
(4)防腐蚀:定期检查逆变器的电路板和元器件,防止湿气和腐蚀物质对设备造成损害。
(5)数据监测:定期监测逆变器的运行数据,如输出功率、电压、电流等,及时发现异常情况并进行处理。
3.逆变器维护要求(1)定期性:逆变器的维护应该按照一定的时间周期进行,一般为每季度或半年进行一次维护。
(2)专业性:逆变器的检修和维护应该由专业的技术人员进行,确保操作准确、安全。
(3)记录备份:对逆变器的维护情况进行记录备份,包括维护日期、维护内容、维护人员等,以备日后查阅和分析。
综上所述,逆变器的检修和定期维护对于确保新能源光伏发电系统的正常运行和发电效率至关重要。
通过对逆变器外观、线路、散热、参数以及设备状态的检查,可以及时发现并处理其中的问题。
(完整版)阳光逆变器检修手册..

中广核太阳能光伏电站阳光逆变器检修维护手册一、逆变器的作用及意义并网逆变器是光伏电站中重要的电气设备,同时也是光伏发电系统中的核心设备。
逆变器将光伏方阵产生的直流电(DC)逆变为三相正弦交流电(AC),输出符合电网要求的电能。
逆变器是进行能量转换的关键设备,其效率指标等电气性能参数,将直接影响电站系统发电量。
逆变器满足以下要求:①并网逆变器的功率因数和电能质量应满足电网要求。
②逆变器额定功率应满足用于海拔高度的要求,其内绝缘等电气性能满足要求。
③逆变器使用太阳电池组件最大功率跟踪技术(MPPT)。
④逆变器具有极性反接保护、短路保护、孤岛效应保护、过温保护、交流过流及直流过流保护、直流母线过电压保护、电网断电、电网过欠压、电网过欠频、光伏阵列及逆变器本身的接地检测及保护功能等,二、逆变器的结构及技术参数公司投产及新建电站部分采用合肥阳光生产的SG500KTL型逆变器,其内部器件布置如下图。
SG500KTL面板元器件如下图所示元件介绍以敦煌光伏电站为例,逆变器主要技术参数如下表所示。
三、逆变器投运前的运维1、逆变器投运前的本体检查检查所有紧固件、连接件是否松动,.检查运输时拆下的零部件是否重新安装妥当(对照逆变器安装手册及施工图),并检查逆变器内部是否有异物存在,特别柜体在运输过程中有无损伤。
检查逆变器室内通风是否良好,轴流风机是否能正常启停。
检查逆变器柜体下部电缆通道是否已清理,防火封堵及防火涂料已按设计施工完毕。
检查逆变器交、直流侧接线是否已联接完毕,且连接线具有明确标识,接线牢固可靠,无松动。
2、逆变器投运前的试验逆变器投运前的各项试验一般由厂家负责完成,现场运维人员可就地观摩,但不能作为实验人员。
通电前,设备交、直流侧的断路器应处于断开状态.测量设备的接地电阻,小于4欧姆。
检查光伏组串的开路电压的一致性,一般偏差2%以内为正常。
带电检查光伏组串与汇流箱、汇流箱与直流柜、直流柜与逆变器的正负极性是否一致。
光伏电站中逆变器日常维护、检修操作步骤及注意事项

光伏电站中逆变器日常维护、检修操作步骤及注意事项光伏电站中的逆变器是将直流电转换为交流电的重要设备,对其进行日常维护和定期检修对于电站的安全运行和电能转换效率具有至关重要的作用。
本文将为您介绍光伏电站中逆变器的日常维护、检修操作步骤和注意事项。
一、日常维护1. 清洁和除尘光伏电站中的逆变器应经常保持清洁,避免灰尘、杂物等附着在其表面,影响散热效果和正常运行。
可定期使用干净、无碱性的布或软刷子清洁逆变器表面,并确保清洗时不对电站其他设备造成损害。
2. 定期检查电缆连接逆变器的工作正常与否与其电缆连接质量密切相关。
定期检查逆变器的电缆连接是否牢固,如发现松动或损坏,应及时加以修复或更换。
同时,注意检查接地线是否连接可靠,确保逆变器的安全接地。
3. 温度监测逆变器工作时,其温度的变化与电能转换效率及设备寿命有直接关系。
应定期检测逆变器的温度,确保其工作温度在正常范围内。
对于超温现象,应及时采取措施加以处理,以防止设备过热引发故障。
4. 通风及散热逆变器在运行过程中会产生一定的热量,为保证其正常工作,应确保其通风良好,散热效果良好。
在逆变器周围保持一定的通风空间,确保空气流通,排除热量,从而提高逆变器的工作效率和寿命。
二、检修操作步骤1. 断电及告警解除在进行逆变器的检修前,应首先切断电源,并解除逆变器上的告警信息。
确保电站和人员的安全。
2. 总览检查检修逆变器前,应对其外观进行总览检查,确认有无明显的损坏或异常情况。
特别需要注意的是风扇是否运转正常,电源电压是否稳定等。
3. 内部检查打开逆变器的外壳,对内部电路进行检查。
注意检查电路板、连接器、触摸接点等是否损坏或脱落,如发现问题应及时修复或更换。
4. 部件维护维护逆变器部件应谨慎操作,避免对其产生过多的压力或碰撞,防止损坏。
对于电容、电感等易损耗的部件,应定期检查并更换,确保设备的正常运行。
5. 参数设置检查逆变器的参数设置直接影响其输出电流、功率等,检修操作时需要对参数进行检查和调整。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
中广核太阳能光伏电站阳光逆变器检修维护手册一、逆变器的作用及意义并网逆变器是光伏电站中重要的电气设备,同时也是光伏发电系统中的核心设备。
逆变器将光伏方阵产生的直流电(DC)逆变为三相正弦交流电(AC),输出符合电网要求的电能。
逆变器是进行能量转换的关键设备,其效率指标等电气性能参数,将直接影响电站系统发电量。
逆变器满足以下要求:①并网逆变器的功率因数和电能质量应满足电网要求。
②逆变器额定功率应满足用于海拔高度的要求,其内绝缘等电气性能满足要求。
③逆变器使用太阳电池组件最大功率跟踪技术(MPPT)。
④逆变器具有极性反接保护、短路保护、孤岛效应保护、过温保护、交流过流及直流过流保护、直流母线过电压保护、电网断电、电网过欠压、电网过欠频、光伏阵列及逆变器本身的接地检测及保护功能等,二、逆变器的结构及技术参数公司投产及新建电站部分采用合肥阳光生产的SG500KTL型逆变器,其内部器件布置如下图。
SG500KTL面板元器件如下图所示元件介绍以敦煌光伏电站为例,逆变器主要技术参数如下表所示。
三、逆变器投运前的运维1、逆变器投运前的本体检查检查所有紧固件、连接件是否松动,。
检查运输时拆下的零部件是否重新安装妥当(对照逆变器安装手册及施工图),并检查逆变器内部是否有异物存在,特别柜体在运输过程中有无损伤。
检查逆变器室内通风是否良好,轴流风机是否能正常启停。
检查逆变器柜体下部电缆通道是否已清理,防火封堵及防火涂料已按设计施工完毕。
检查逆变器交、直流侧接线是否已联接完毕,且连接线具有明确标识,接线牢固可靠,无松动。
2、逆变器投运前的试验逆变器投运前的各项试验一般由厂家负责完成,现场运维人员可就地观摩,但不能作为实验人员。
通电前,设备交、直流侧的断路器应处于断开状态。
测量设备的接地电阻,小于4欧姆。
检查光伏组串的开路电压的一致性,一般偏差2%以内为正常。
带电检查光伏组串与汇流箱、汇流箱与直流柜、直流柜与逆变器的正负极性是否一致。
逆变器初次带电调试时,按照10%、30%、60%、100%负载逐步投入,时间间隔约5分钟左右。
逆变器大功率带载时,禁止直接分断交直流侧的断路器,可通过触摸屏菜单发出关机指令,减小对电网的冲击。
运行时应无电气异味,无异常声,散热正常,接线端子无发黑以及无打火现象。
四、逆变器并网运行的运维1、并网运行上电之前,要确认逆变器所有的直流输入和交流输入断路器都处于“断开”(包含直流配电柜的空开也应在“断开”)位置。
对于首次开机,要严格按照逆变器随机说明书进行操作,以后运行开机应先合交流侧断路器,再合直流侧断路器。
逆变器的调试要严格按照调试步骤来进行,填写调试数据,如果出现异常情况,要停电进行查找故障,只有找到原因,恢复好后,确认无误,才可以重新进行调试。
首次开机流程图(单台逆变器)①合上每台汇流箱的每一路串列正负极高压保险丝②该方阵全部汇流箱直流输出断路器全合上③合上直流配电柜里任意一个直流输入断路器④合上逆变器直流侧2个输入断路器⑤约30S后断开逆变器已合上直流侧2个输入断路器(操作这几步是为了首次开机给母线的电容预充电,主要针对高压、大功率逆变器的首次调试)。
⑥合上逆变器交流侧输出断路器⑦再合上逆变器直流侧2个输入断路器⑧依次合上直流配电柜其它的直流输入断路器⑨逆变器开机并投入运行2、并网后的检查保证逆变器正常运行需要定期巡检,在新投运、改造后或大修后72小时内、在有严重缺陷、高负荷期或环境温度较高时,更应该增加巡检次数。
巡检时应注意以下三个方面。
温度:逆变器能正常运行温度是一个重要的指标。
由于电站投运时间的不同,环境温度及负荷状况对逆变器温度有较大的影响。
逆变器首次投运并带满负荷后,作为现场运维人员应在运行记录中详细记录逆变器的柜内温度。
在随后的一周时间内,逆变器每运行1小时,记录一次柜内温度,当发现温度变化突升5℃以上时,应立即去就地对逆变器进行检查。
在检查过程中,现场运维人员必须使用温度测试仪或热成像仪,对变压器本体及接线端子等附件进行有针对性的检查。
(当逆变器室内有金属焦臭味时,应停机打开柜门检查)。
声音:逆变器正常运行时,声音是均匀硅整流及冷却风扇运行声音。
如发现声音异常,明显增大、或者存在局部放电响声,应该立即找出原因、采取措施。
当发生上述情况时,应采取降负荷乃至停运逆变器等技术手段。
(停机时,除非发生威胁人身或设备损坏的情况,采用柜体急停按钮;通常情况下应在触摸显示的人机画面中停机。
)通风:逆变器在运行中,保障通风对逆变器的高效稳定运行有着积极的作用。
通风量的下降或通风设备故障都会限制逆变器的出力、甚至导致逆变器停运。
在巡检过程中,运维人员应加强对逆变器本体通风及逆变器室通风的检查,正常状态下,逆变器本体风扇应保持工作;当柜体内温度或室内温度高于设定值时(具体数值为所在电站自行设定),室内轴流风机应立即启动。
在巡检过程中,运维人员当发现逆变器室温度过高、而轴流风机未及时启动时,应立即手动启动。
如轴流风机故障,则应采取打开逆变器室门、窗予以通风散热。
五、逆变器正常运行中的维护1、检修周期:①检修随电站的每年春、秋检进行(暨电站的预防性维护)②检查10MWp-30MWp电站每周进行一次;30MWp-50MWp电站每15天进行一次;50MWp-100MWp电站每月进行一次。
所有逆变器应保障在夏季高温期间或持续高负荷期间每月进行一次检查。
(当沙尘天气后应立即检查)2、检查、修项目①检查项目逆变器的安装状况。
逆变器通风滤网的积灰性。
逆变器周围环境是否不利于运行。
逆变器通风状况和温度检测装置检验。
逆变器有无过热存在。
逆变器引线支持状态及接线端子。
逆变器各部连接状况。
逆变器接地状态。
逆变器室灰尘状态。
逆变器室轴流风机及风道状态。
注:电站应结合环境及实际情况,在检查项的规定时间内,对逆变器的滤网、逆变器室的积灰进行清理,在对逆变器进行检查时,应使用热成像仪对设备进行检查。
②检修项目清除逆变器内外灰尘、污垢及水份等。
更换和检修易损零件(特别是逆变器本体通风风扇)。
包括检查项目的全部内容。
2、检修工艺①检查逆变器的安装是否完整,有无歪斜,局部变形及震动现象。
逆变器外壳是否完整,各连接是否松动,箱壳各处有无碰坏现象。
逆变器周围环境是否清洁,有无积水、顶上漏水及其他妨碍安全运行的物件。
检查逆变器室的通风设备,应能正常通风。
逆变器各部位有无局部过热现象,各部温度是否正常,是否超过现定值。
逆变器引线是否牢固,位置是否正常,引线四周绝缘距离是否有改变。
逆变器各处连接螺栓有无松动现象,逆变器有无不正常之噪音。
接线板等处的电气连接部分有无松动及局部过热现象,内部母排连接是否牢固,,然后清除逆变器内部的污物及灰尘。
逆变器接地是否可靠。
测量逆变器至干变的绝缘电阻。
应无孔洞、缝隙能进入危及安全的小动物。
②检修了解逆变器在运行中所发现的缺陷和异常(事故)情况。
逆变器上次检修的技术资料和技术档案。
了解逆变器的运行状况(负荷、温度、其他附属装置的运行情况)。
查阅逆变器的原试验记录,了解逆变器的绝缘状况。
拆卸的螺栓零件应用去污剂清洗,如有损坏应修理或更换,然后妥善保管,防止丢失或损坏。
拆卸时应先对逆变器本体进行放电(逆变器投运后电容及直流母排内仍存有电),放电10min后验电,再拆卸逆变器柜门,组装时顺序相反。
逆变器检修时,原则上对控制单元不进行拆除检修,只进行清扫和紧固端子。
当遇特殊情况需要检修时,应预先联系厂家,手戴静电环检修维护。
下图为逆变器控制盒及元件介绍:F 转接板通道信号的采集出力G DSP板控制模块CPU全面检查逆变器的完整性,有无缺陷存在(如过热、弧痕、松动、线圈变形、接点变色等)。
对异常情况要查找原因并进行检修处理,同时要作好记录。
检查逆变器输入、输出接线端子,有无破损、变色、变形、放电痕迹,如发现异常,应做针对处理。
检查逆变器防雷器是否需要更换(正常为绿色,红色则更换)。
检查逆变器风道及轴流风机,有无被污垢或其他物质堵塞情况,必要时可用软毛刷擦拭。
检查交流LC滤波器中的三项电抗器。
铁芯外表是否平整,有无片间短路或变色、放电烧伤痕迹、有无松脱,上铁轭顶部和下铁轭的底部是否积聚的污垢杂物,应进行清扫擦拭,若迭片有翘起或不规则之处,可用木锤或铜锤敲打平整。
检查电抗铁心,上下夹件、方铁、线圈压板(包括压铁)的紧固度和绝缘情况。
LC三相电抗如下图所示:检查电抗引线的绝缘包扎情况,有无变形、变脆、破损,引线有无断股,引线与引线接头处焊接是否良好,有无过热现象。
检查电抗绝缘支架有无松动和裂纹、位移情况,检查引线在绝缘支架内固定情况。
检查电抗引线与各部位之间的绝缘距离。
用电吹风或压缩空气从不同角度冲扫逆变器内外,以不见灰尘吹出为结束;要注意空气流速不致过大,以免凝结水吹向器身。
先将逆变器本体清扫完毕后,再清扫逆变器室。
更换和检修易损部件,比如控制电源模块、内部接线(特别是交流侧滤波电容电缆)、进出电缆头等。
SG500KTL逆变器常见故障分析:③逆变器检修后的试运行⑴、逆变器检修竣工后,应清理现场、整理记录、资料、图纸,办理工作票终结手续。
⑵、试运行前检查项目逆变器柜内冷却装置及室内通风所有附件均无缺陷,且无污迹。
逆变器本体固定装置牢固。
油漆完整,接地可靠。
逆变器顶部无遗留杂物。
与外部引线的连接接触良好。
⑶、试运行逆变器试运行时应按下列进行检查:按操作顺序先合交流侧、后合直流侧。
受电后,逆变器直流侧开关应逐步投运,让逆变器逐步带负荷并直至直流侧全部投运。
带电后,检查逆变器应无异常放电声及异味。
注:检修过程需严格遵守安全措施,所有检修必须持有现场人员签发的工作票,停送电时必须持有操作票并唱票复诵。
附件:光伏发电设备检修作业程序光伏发电系统设备检修作业程序一、引用的技术标准或技术资料产品说明书电站设备检修规程二、修前准备□资料准备□了解一次设备运行方式□阅读设备说明书及变压器检修总结报告;□阅读设备台帐、缺陷记录、检修资料□检修时的技术措施和组织措施方案;□分析设备运行状况,明确缺陷和检修内容。
□熟悉检修安全注意事项,分析危险点□了解检修范围、工作环境□掌握检修工艺及质量标准□前期设备诊断□检查并记录:设备运行缺陷情况:共项□上次检修到本次检修的设备运行周期:□检修周期内设备运行情况描述:□仪器、仪表准备□温湿度仪 (1)台□测温仪……………………………………………………………………1台□500V摇表…………………………………………………………………1块□1000V摇表………………………………………………………………1块□万用表……………………………………………………………………1块□钳形电流表…………………………………………………………1台□工具准备□螺丝刀(十字口)...............................................................2把□螺丝刀(一字口)...............................................................2把□尖嘴钳..............................................................................1把□活扳手(4"、6"、8"、12") (1)□内六角扳手........................................................................1套□套筒扳手...........................................................................1套□呆头扳手(17—19、22—24) (1)□梅花扳手(17—19、22—24) (1)□电缆卷线盘………………………………………………………………2个□安全带……………………………………………………………………3付□材料准备□破布………………………………………………………………… 5 Kg □工业酒精…………………………………………………………………2 Kg □导电膏……………………………………………………………………1管□塑料带(黄、绿、红)……………………………………………………2kg □白布带……………………………………………………………………5盘□松动剂……………………………………………………………………1瓶□毛刷………………………………………………………………………5把□强力吹风机…………………………………………………………… 1台□吸尘器………………………………………………………………… 1台□轮换备件…………………………………………………………………按需□电池组件…………………………………………………………………5块□汇流箱…………………………………………………………………2面四、检修工序1、逆变器检修□外观、清扫检查;□柜体滤尘网清扫、更换;□内部设备清扫,清洁无灰尘。