锻模术语中英文对照表
锻造术语中英文对照
锻造术语中英文对照锻压forging and stamping金属塑性加工metal plastic working金属压力加工mechanical metal working体积成形bulk forming锻造forging / hot forging锻造技术forging technology / forging technique锻造工艺forging technology / forging process锻工forger / blacksmith / hammer man / hammer smith / hammerer塑性plasticity超塑性superplasticity可锻性forgeability切削性能machinability最小阻力定律the law of minimum resistance体积不变条件constance(y) of volume / incompressibility锻造流线grain flow / forging flow line滑移线sliding line / slip-line模锻die forging / closed-die forging / impression die forging开式模锻closed-die forging / impression die forging闭式模锻no-flash die forging / flashless die forging锤模锻closed-die forging / impression die forging / drop forging / stamping锻压机模锻mechanical press forging平锻upsetting / heading无飞边模锻no-flash forging无拔模斜度模锻no-draft forging模锻件forging / workpiece锻件重量forging weight普通锻件conventional forging精确（公差）锻件close-tolerance forging锻造工序卡forging process chart工序operation / process / procedure工步process step打击blow / strike锻件图forging drawing加工余量machining allowance镦锻、顶锻upsetting / heading镦粗upsetting压扁flattening去氧化皮scale-breaking拔长工步drawing / elongating / fullering拔夹钳头tong-hold drawn / tagging滚压工步edging / edge rolling / gathering弯曲工步bending制坯工步pre-forming平锻聚料gathering / pushing up / upsetting锥形镦粗taper upsetting / coning粗（初）锻blocker-type forging预锻pre-forging / blocking终锻finish-forging返回锻模校正re-striking分模线parting line模锻斜度、拔模角、拔模斜度draft angle外拔模角outside draft内拔模角inside draft自然拔模角natural draft相配拔模角matching draft外圆角corner内圆角fillet未注明圆角all radii not specified尺寸按交点注all dimensions specified form intersections 模锻方案forging form一料多件multi-forging on one billet (bar)一模两件two at a time一模多件multi at a time调头锻turn-end forging一火多件multi-forging in one heat打零件号、炉号码及模具号处raise part No. heat code and die No. here除注明处外unless otherwise noted冲孔、切边、校正冲连皮punching the wad / punching the slug冲孔pierce盲孔non-penetrated hole / blind hole连皮wad / recess / slug切边clipping / trimming飞边flash残余飞边、残余飞刺flash extension / residual flash切边线、飞边线flash line / trim line整形forming to size校平flattening / planishing校直straightening精压、压印coining / sizing校正sizing / setting冷校正cold sizing / cold setting锻造公差、锻造缺陷及检查锻造公差forging tolerance / tolerance for impression die forging 确定公差的因素information required in determining tolerance锻件形状复杂系数shape complexity factor of forging材质系数difficulty of material分模线形状shape of die line公差等级tolerance grad锻件公称尺寸nominal dimension of forging厚度公差thickness tolerance模具闭合公差die closure tolerance长度、宽度、高度公差length 、width and height tolerance模具磨损公差die wear tolerance错差、错差公差mismatch / match tolerance中心距公差tolerance for centre to centre dimensions平面度公差platness tolerance直线度公差straightness tolerance残余飞边及切入深度公差residual flash and trimmed flat tolerance 顶杆压痕公差ejector mark tolerance表面缺陷公差surface tolerance壁厚差difference in wall thickness冲孔公差pierced hole tolerance同轴度公差axiality tolerance折叠、折纹lap / overlap / fold缺肉、未充满under-fill模锻不足under-pressing表面缺陷surface imperfection氧化皮坑scale pit变形distortion / deformation毛刺、飞刺burr / fin凹陷void出气孔金属柱vent plug偏心eccentricity中间检查intermediate inspection流动检查patrol inspection外观检查visual inspection最后检查final inspection抽检random inspection其他锻造方法多向模锻multi-ram forging / multidirectional die forging 精密模锻precision forging闭塞模锻croe forging合锻combination forging挤压锻造extrusion forging挤压extrusion正挤压forward extrusion / direct extrusion反挤压backward extrusion / indirect extrusion复合挤压combined extrusion辊锻roll forging / reducer rolling制坯辊锻roll forging of blank成形辊锻finishing roll forging辗环ring rolling楔横轧cross wedge rolling / transverse rolling超塑成形superplastic forming等温锻造isothermal forging冷锻cold forging温锻warm forging无屑加工chipless working粉末锻造powder metal forging / powder forging液态模锻melted metal squeezing电热镦electric upset forging摆辗swing-rolling / rock rolling / tambling转动辗压turn-rolling / rotary-rolling径向锻造radial forging自由锻自由锻open die forging / flat die forging胎模锻loose tooling forging送进量feed延伸系数coefficient of stretching高径比ratio of height to diameter锻造比forging ratio镦粗upsetting局部镦粗local upsetting拔长drawing out / stretching / swaging / fullering芯棒拔长drawing out with the core bar滚圆、摔圆rolling倒棱chamfering压痕、克印indentation压肩necking错料offset弯曲bending扭转twisting切割、切断cutting冲孔punching / piercing扩孔expanding冲头扩孔expanding with a punch马杠扩孔、码圈saddle forging / saddling锻接forging welding空冷air cooling堆冷cooling in heap(pile)坑冷cooling in hole(box、pit)灰砂冷cooling in dust or sand炉冷furnace cooling塌角rollover / shear droop龟裂crazing角裂chink中心裂纹chevron crack发纹hairline cracks / hair-crack铁砧anvil花砧swage block冲子punch剁刀triangular chisel摔子tups / swager / swaging die胎模loose tooling马架mandrel supporter芯轴、马杠mandrel手锤hand hammer大锤sledge hammer夹钳tong自紧吊钳self closing crane tong锻压设备及装置锻锤forging hammer落锤drop hammer单作用锤drop hammer双作用锤double-action hammer重力落锤gravity-drop hammer夹板锤board drop hammer / board drop gravity hammer 皮带锤belt drop hammer链条锤chain drop hammer模锻锤die forging hammer蒸汽-空气模锻锤steam or air dir forging hammer锤头ram砧座anvil-block下砧座、砧套、夹持器anvil cap / sow block对击锤counter-blow hammer高速锤high energy rate forging hammer液压机hydraulic press快速锻造液压机high speed forging hydraulic press机械压力机mechanical press曲柄压力机crank press热模锻压力机、锻压机forging press楔式锻压机wedge-tyoe mechanical press开式压力机c-frame press / gap frame press闭式压力机straight side press单点压力机single point press双点压力机two point press单动压力机single action press双动压力机double action press滑块slide / ram导轨guide工作台table / bed顶出器ejector平锻机horizontal forging machine / forging machine / upsetter切边压力机trimming press校正压力机restriking press精压机、肘杆式精压机coining press / knuckle joint coining press 液压曲柄扭转机、扭转机hydraulic twister for crank-shaft / twister 多工位自动热锻机multistage automatic hot forging machine / automatic forging-pressing machine哈德堡热成形机HATEBUR metal-forming equipment / HATEBUR hotmatic 螺旋压力机screw press摩擦压力机friction screw press液压螺旋压力机hydraulic screw press径向锻轴机radial forging machineGFM自动模锻机GFM automatic die forging machine感应抛丸机stress abrator抛丸清理室shot blasting cleaning chamber抛丸机wheel abrator / throw shot machine喷丸机shot blasting machine / peening machine起重机crane桥式起重机overhead traveling crane / bridge type crane塔式起重机tower crane起重葫芦hoist电动葫芦electric hoist气动葫芦pneumatic hoist磁粉探伤机magnetic particle detector荧光磁粉探伤机fluorescent magnetic particle detector无损探伤机non-destructive inspection machine硬度计hardness tester布式硬度计Brinell hardness tester洛式硬度计Rockwell hardness tester金属材料试验机metallic material testing machine非金属材料试验机non-metallic material testing machine拉力试验机tensile testing machine压力试验机compression testing machine扭转试验机torsion testing machine疲劳试验机fatigue testing machine冲击试验机impact testing machine弯折试验机reverse bend tester显微镜microscope金相显微镜metallographic microscope试样（样品）specimen辊锻机forging roll扩孔机ring rolling machine瓦格纳环轧机WAGNER ring roll摆辗机rotary forging press快速换模装置quick die change device换模翻转装置tool changing and turnover fixture锻造自动线automated forging line机械手manipulator / mechanical hand / mechanical operated arm 除氧化皮装置descaler高压水去氧化皮high pressure hydro-peening传送装置transfer equipment悬挂输送链suspension conveyer chain链式传送带chain conveyer板式传送带pallet conveyer毛坯滑道stock guide工件箱parts gondola / work bin飞边箱flash gondola / flash bin型号type / model公称压力capacity / nominal force锻造吨位forging tonnage落下部分重量droping weight / weight of falling每分钟打击次数blow per minute / strick per minute打击速度blow speed打击效率blow efficiency滑块行程stroke of ram行程次数number of stroke滑块行程调节量adjustment of ram stroke下死点lower dead point / bottom dead centre上死点upper dead point / top dead centre寸动inching最大装模高度maximum die set height最大封闭高度maximum shut height空气锤pneumatic hammer / air hammer锻件热处理锻件热处理forging heat-treatment加热规范heating schedule正火normalizing淬火quench-hardening / hardening / quenching回火tempering调质quenching and tempering / hardening and tempering 退火annealing等温退火isothermal annealing形变热处理thermomechanical treatment (TMT)锻件余热淬火quenching from forging heat残余应力residual stress消除残余应力stress relieving淬火裂纹quenching crack / hardening flaw淬火应力quenching stress / hardening stress淬火介质quenching medium拉长淬火机stretch-quench machine硬度hardness布式硬度试验Brinell hardness test / Brinelling洛式硬度试验Rockwell hardness test锻件清理抛丸清理shot-blasting / peening抛丸室（机）shot-blast chamber(machine)喷砂清理sand blast cleaning酸洗pickling / dipping滚筒清理tumbling / roller cleaning磨毛刺grinding / burring设备分类工艺设备manufacturing equipment标准设备standard equipment非标准设备non-standard equipment通用设备vniversal equipment专用设备special equipment热处理设备heat treatment equipment热处理主要设备main equipment for heat treatment热处理辅助设备auxiliary equipment for heat treatment热处理成套设备（热处理生产线）complete set of heat treatment equipment热处理炉heat treatment furnace燃料炉fuel-fired furnace燃气炉gas-fired furnace燃油炉oil-fired furnace燃煤炉coal-fired furnace电热设备electro-heat installation电热装置electro-heat equipment工作温度working temperature工作区尺寸working space dimensions生产率production rate额定温度rated temperature炉温自动控制automatic control of furnace temperature炉温程序控制program control of furnace temperature炉温的时间比例控制time ratio control of furnace temperature 风室wind chamber连续式炉continuous furnace多区域炉multi-zone furnace感应加热设备表面加热surface heating感应加热induction heating工频mains frequency低频low frequency中频medium frequency超音频ultrasonic frequency高频high frequency超高频ultrahigh frequency感应加热设备induction heating equipment。
锻造专业 词语中西英文对照
31 Achaflanado
32 Acu?ado
33 Afinado en electroescoria
34 Agujeros de viento en la matriz
35 Ahorro (costos)
36 Aire comprimido
37 Aislamiento
38 Ajuste
39 Ajuste de la carrera
40 Ajuste con apriete
41 Alambre
42 Alabe de turbina
43 Aleación de aluminio
44 Aleación de alta resistencia
45 Aleación resistente al calor
46 Aleación superfrefractaria
8 Accionamiento de la prensa
9 Acciones correctoras
10 Accidentes
11 Aceptación
12 Acero
13 Acero aleado
14 Acero al carbono
15 Acero de cementación
16 Acero de construcción
锻造专业词语中西英文对照
序 号
西语
1 Abrasivos
2 Acabado
3 Accionamiento de un martillo
4 Accionamiento mecánico
6 Accionado por correas
7 Accionado por manivela
99 Calentadora 100 Calentamient sin oxidación 101 Calentamiento eléctrico 102 Calentamiento por convección 103 Calentamiento por inducción 104 Calentamiento por infra-rojos 105 Calentamiento por resistencia 106 Calentamiento rápido 107 Calentamiento por conducción 108 Calibrado 109 Calibre de medida 110 Calor de forja 111 Calorifugado 112 Campo de temperatures 113 Capacidad de deformación 114 Capacidad del horno 115 Cara de fijación de las matrices 116 Características físicas 117 Caracteristicas mecánicas 118 Carbonitruración 119 Carga de rotura 120 Carrera del golpe 121 Carretilla 122 Cascarilla 123 Cementación 124 Cigüeñal 125 Cimentación 126 Cincelado de defectos 127 Cinta transportadora 128 Cizalla 129 Cizallado 130 Clava cuñas 131 Coeficiente de forja 132 Coeficiente de rozamiento 133 Coeficiente de dificultad de forma 134 Cojinete 135 Cola del punzón 136 Colada continua 137 Cola de milano 138 Cola de agarre en el taco para tenazas 139 Colchon de amortiguación 140 Columnas de martillo 141 Columna de la prensa 142 Combustible 143 Combustión 144 Compactación por prensado (met.en 145 Compresión 146 Condiciones de suministro 147 Condiciones de recepción 148 Conductibilidad térmica 149 Conformado
最全模具行业术语英文翻译
hole for screw
行位槽：
slide scot/scot for slide
喷砂：
engraving
螺母：
Nuts screw:
螺杆
导套：
guide bushing
try out:
试模
配镶件
making inserts
装配：
assemble
晒纹：
texturing
运水孔：
hole for water line
弹簧复位
manifold
热流道板
draft
斜度
热唧嘴hot runner
Inserted
镶件模
行位（滑块）：
slide
镶件：
insert
推板：
stripper plate
斜顶：
lifter
undercut倒扣/里面
Driller
钻床
flash披风
rib骨位一.
模具加工方法英语词汇四.
模具线切割放电加工相关英语词汇
顶料销
锁模块：
lock plate
斜顶：
lifters
Miller Milling Machine
铣床
快速接头：
jiffy quick connector plug/socker
Dowel Pin
定位梢
turnnel
隧道进浇
镶针
insert pin
排气槽: scot for venting
胶位: plastic
ball catch
喉塞: pipe plug
流道平衡:runner balance
斜顶杆：
angle ejector rod
锻造用英语术语
锻造用英语术语filling in 填砂film play 液面花纹finishing slag 炼后熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心。
各式模具加工分类用语中英文对照
die life 模 具寿命 die opening 母模逃孔
die spotting press 调 整冲模用 压力机 double crank press 双 曲柄轴冲 床
counter punch 反 凸模
modular mold 组 合式模具 double stack mold 双 层模具
各种冲模 加工关连 用语
barreling 滚光加工
belling 压 凸加工 bending 弯曲加工
blanking 下料加工
bulging 撑压加工 burring 冲缘加工 cam die bending 凸轮弯曲 加工 coining 压印加工
curling 卷 曲加工
cutting 切削加工
dinking 切断蕊骨
double shearing 叠板裁断
drawing 引伸加工
drawing with ironing 抽引光滑 加工
embossi ng 浮花 压制加工
extrusion 挤制加 工
duplicate d cavity plate 复 板模
edging 边锻伸
system 系统 tape 磁带
terminal 终端机 texture 构造 trim 修边 word processo r 文书处 理器
模具加工 方法
barrel 滚 筒(加工) bending 波纹加工 broachin g 拉刀切 削
embedde d core 加 装砂心 feed length 送 料长度 feed level 送 料高度 filling core 埋入 砂心 filling in 填砂
锻造术语中英文对照
锻造术语中英文对照锻压 forging and stamping金属塑性加工 metal plastic working金属压力加工 mechanical metal working体积成形 bulk forming锻造 forging / hot forging锻造技术 forging technology / forging technique锻造工艺 forging technology / forging process锻工 forger / blacksmith / hammer man / hammer smith / hammerer塑性 plasticity超塑性 superplasticity可锻性 forgeability切削性能 machinability最小阻力定律 the law of minimum resistance体积不变条件 constance(y) of volume / incompressibility锻造流线 grain flow / forging flow line滑移线 sliding line / slip-line模锻 die forging / closed-die forging / impression die forging开式模锻 closed-die forging / impression die forging闭式模锻 no-flash die forging / flashless die forging锤模锻 closed-die forging / impression die forging / drop forging / stamping 锻压机模锻 mechanical press forging平锻 upsetting / heading无飞边模锻 no-flash forging无拔模斜度模锻 no-draft forging模锻件 forging / workpiece锻件重量 forging weight普通锻件 conventional forging精确（公差）锻件 close-tolerance forging锻造工序卡 forging process chart工序 operation / process / procedure工步 process step打击 blow / strike锻件图 forging drawing加工余量 machining allowance镦锻、顶锻 upsetting / heading镦粗 upsetting压扁 flattening去氧化皮 scale-breaking拔长工步 drawing / elongating / fullering拔夹钳头 tong-hold drawn / tagging滚压工步 edging / edge rolling / gathering弯曲工步 bending制坯工步 pre-forming平锻聚料 gathering / pushing up / upsetting锥形镦粗 taper upsetting / coning粗（初）锻 blocker-type forging预锻 pre-forging / blocking终锻 finish-forging返回锻模校正 re-striking分模线 parting line模锻斜度、拔模角、拔模斜度 draft angle外拔模角 outside draft内拔模角 inside draft自然拔模角 natural draft相配拔模角 matching draft外圆角 corner内圆角 fillet未注明圆角 all radii not specified尺寸按交点注 all dimensions specified form intersections模锻方案 forging form一料多件 multi-forging on one billet (bar)一模两件 two at a time一模多件 multi at a time调头锻 turn-end forging一火多件 multi-forging in one heat打零件号、炉号码及模具号处 raise part No. heat code and die No. here 除注明处外 unless otherwise noted冲孔、切边、校正冲连皮 punching the wad / punching the slug冲孔 pierce盲孔 non-penetrated hole / blind hole连皮 wad / recess / slug切边 clipping / trimming飞边 flash残余飞边、残余飞刺 flash extension / residual flash切边线、飞边线 flash line / trim line整形 forming to size校平 flattening / planishing校直 straightening精压、压印 coining / sizing校正 sizing / setting冷校正 cold sizing / cold setting锻造公差、锻造缺陷及检查锻造公差 forging tolerance / tolerance for impression die forging 确定公差的因素 information required in determining tolerance锻件形状复杂系数 shape complexity factor of forging材质系数 difficulty of material分模线形状 shape of die line公差等级 tolerance grad锻件公称尺寸 nominal dimension of forging厚度公差 thickness tolerance模具闭合公差 die closure tolerance长度、宽度、高度公差 length 、width and height tolerance模具磨损公差 die wear tolerance错差、错差公差 mismatch / match tolerance中心距公差 tolerance for centre to centre dimensions平面度公差 platness tolerance直线度公差 straightness tolerance残余飞边及切入深度公差 residual flash and trimmed flat tolerance 顶杆压痕公差 ejector mark tolerance表面缺陷公差 surface tolerance壁厚差 difference in wall thickness冲孔公差 pierced hole tolerance同轴度公差 axiality tolerance折叠、折纹 lap / overlap / fold缺肉、未充满 under-fill模锻不足 under-pressing表面缺陷 surface imperfection氧化皮坑 scale pit变形 distortion / deformation毛刺、飞刺 burr / fin凹陷 void出气孔金属柱 vent plug偏心 eccentricity中间检查 intermediate inspection流动检查 patrol inspection外观检查 visual inspection最后检查 final inspection抽检 random inspection其他锻造方法多向模锻 multi-ram forging / multidirectional die forging精密模锻 precision forging闭塞模锻 croe forging合锻combination forging挤压锻造 extrusion forging挤压 extrusion正挤压 forward extrusion / direct extrusion反挤压 backward extrusion / indirect extrusion复合挤压 combined extrusion辊锻 roll forging / reducer rolling制坯辊锻 roll forging of blank成形辊锻 finishing roll forging辗环 ring rolling楔横轧 cross wedge rolling / transverse rolling 超塑成形 superplastic forming等温锻造 isothermal forging冷锻 cold forging温锻 warm forging无屑加工 chipless working粉末锻造 powder metal forging / powder forging液态模锻 melted metal squeezing电热镦 electric upset forging摆辗 swing-rolling / rock rolling / tambling转动辗压 turn-rolling / rotary-rolling径向锻造 radial forging自由锻自由锻 open die forging / flat die forging胎模锻 loose tooling forging送进量 feed延伸系数 coefficient of stretching高径比 ratio of height to diameter锻造比 forging ratio镦粗 upsetting局部镦粗 local upsetting拔长 drawing out / stretching / swaging / fullering 芯棒拔长 drawing out with the core bar滚圆、摔圆 rolling倒棱 chamfering压痕、克印 indentation压肩 necking错料 offset弯曲 bending扭转 twisting切割、切断 cutting冲孔 punching / piercing扩孔 expanding冲头扩孔 expanding with a punch马杠扩孔、码圈 saddle forging / saddling锻接 forging welding空冷 air cooling堆冷 cooling in heap(pile)坑冷 cooling in hole(box、pit)灰砂冷 cooling in dust or sand炉冷 furnace cooling塌角 rollover / shear droop龟裂 crazing角裂 chink中心裂纹 chevron crack发纹 hairline cracks / hair-crack铁砧 anvil花砧 swage block冲子 punch剁刀 triangular chisel摔子 tups / swager / swaging die胎模 loose tooling马架 mandrel supporter芯轴、马杠 mandrel手锤 hand hammer大锤 sledge hammer夹钳 tong自紧吊钳 self closing crane tong锻压设备及装置锻锤 forging hammer落锤 drop hammer单作用锤 drop hammer双作用锤 double-action hammer重力落锤 gravity-drop hammer夹板锤 board drop hammer / board drop gravity hammer 皮带锤 belt drop hammer链条锤 chain drop hammer模锻锤 die forging hammer蒸汽-空气模锻锤 steam or air dir forging hammer锤头 ram砧座 anvil-block下砧座、砧套、夹持器 anvil cap / sow block对击锤 counter-blow hammer高速锤 high energy rate forging hammer液压机 hydraulic press快速锻造液压机 high speed forging hydraulic press机械压力机 mechanical press曲柄压力机 crank press热模锻压力机、锻压机 forging press楔式锻压机 wedge-tyoe mechanical press开式压力机 c-frame press / gap frame press闭式压力机 straight side press单点压力机 single point press双点压力机 two point press单动压力机 single action press双动压力机 double action press滑块 slide / ram导轨 guide工作台 table / bed顶出器 ejector平锻机 horizontal forging machine / forging machine / upsetter切边压力机 trimming press校正压力机 restriking press精压机、肘杆式精压机 coining press / knuckle joint coining press 液压曲柄扭转机、扭转机 hydraulic twister for crank-shaft / twister 多工位自动热锻机 multistage automatic hot forging machine / automatic forging-pressing machine哈德堡热成形机 HATEBUR metal-forming equipment / HATEBUR hotmatic 螺旋压力机 screw press摩擦压力机 friction screw press液压螺旋压力机 hydraulic screw press径向锻轴机 radial forging machineGFM自动模锻机 GFM automatic die forging machine感应抛丸机 stress abrator抛丸清理室 shot blasting cleaning chamber抛丸机 wheel abrator / throw shot machine喷丸机 shot blasting machine / peening machine起重机 crane桥式起重机 overhead traveling crane / bridge type crane塔式起重机 tower crane起重葫芦 hoist电动葫芦 electric hoist气动葫芦 pneumatic hoist磁粉探伤机 magnetic particle detector荧光磁粉探伤机 fluorescent magnetic particle detector无损探伤机 non-destructive inspection machine硬度计 hardness tester布式硬度计 Brinell hardness tester洛式硬度计 Rockwell hardness tester金属材料试验机 metallic material testing machine非金属材料试验机 non-metallic material testing machine拉力试验机 tensile testing machine压力试验机 compression testing machine扭转试验机 torsion testing machine疲劳试验机 fatigue testing machine冲击试验机 impact testing machine弯折试验机 reverse bend tester显微镜 microscope金相显微镜 metallographic microscope试样（样品） specimen辊锻机 forging roll扩孔机 ring rolling machine瓦格纳环轧机 WAGNER ring roll摆辗机 rotary forging press快速换模装置 quick die change device换模翻转装置 tool changing and turnover fixture锻造自动线 automated forging line机械手 manipulator / mechanical hand / mechanical operated arm 除氧化皮装置 descaler高压水去氧化皮 high pressure hydro-peening传送装置 transfer equipment悬挂输送链 suspension conveyer chain链式传送带 chain conveyer板式传送带 pallet conveyer毛坯滑道 stock guide工件箱 parts gondola / work bin飞边箱 flash gondola / flash bin型号 type / model公称压力 capacity / nominal force锻造吨位 forging tonnage落下部分重量 droping weight / weight of falling每分钟打击次数 blow per minute / strick per minute打击速度 blow speed打击效率 blow efficiency滑块行程stroke of ram行程次数 number of stroke滑块行程调节量 adjustment of ram stroke下死点 lower dead point / bottom dead centre上死点 upper dead point / top dead centre寸动 inching最大装模高度 maximum die set height最大封闭高度 maximum shut height空气锤 pneumatic hammer / air hammer锻件热处理锻件热处理 forging heat-treatment加热规范 heating schedule正火 normalizing淬火 quench-hardening / hardening / quenching回火 tempering调质 quenching and tempering / hardening and tempering退火 annealing等温退火 isothermal annealing形变热处理 thermomechanical treatment (TMT)锻件余热淬火 quenching from forging heat残余应力 residual stress消除残余应力 stress relieving淬火裂纹 quenching crack / hardening flaw淬火应力 quenching stress / hardening stress淬火介质 quenching medium拉长淬火机 stretch-quench machine硬度 hardness布式硬度试验 Brinell hardness test / Brinelling洛式硬度试验 Rockwell hardness test锻件清理抛丸清理 shot-blasting / peening抛丸室（机） shot-blast chamber(machine)喷砂清理 sand blast cleaning酸洗 pickling / dipping滚筒清理 tumbling / roller cleaning磨毛刺 grinding / burring设备分类工艺设备 manufacturing equipment标准设备 standard equipment非标准设备 non-standard equipment通用设备 vniversal equipment专用设备 special equipment热处理设备 heat treatment equipment热处理主要设备 main equipment for heat treatment热处理辅助设备 auxiliary equipment for heat treatment热处理成套设备（热处理生产线） complete set of heat treatment equipment 热处理炉 heat treatment furnace燃料炉 fuel-fired furnace燃气炉 gas-fired furnace燃油炉 oil-fired furnace燃煤炉 coal-fired furnace电热设备 electro-heat installation电热装置 electro-heat equipment工作温度 working temperature工作区尺寸 working space dimensions生产率 production rate额定温度 rated temperature炉温自动控制 automatic control of furnace temperature炉温程序控制 program control of furnace temperature炉温的时间比例控制 time ratio control of furnace temperature 风室 wind chamber连续式炉 continuous furnace多区域炉 multi-zone furnace感应加热设备表面加热 surface heating感应加热 induction heating工频 mains frequency低频 low frequency中频 medium frequency超音频 ultrasonic frequency高频 high frequency超高频 ultrahigh frequency感应加热设备 induction heating equipment。
锻造用英语术语
锻造用英语术语锻造用英语术语filling in 填砂film play 液面花纹finishing slag 炼后熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心。
模具术语英文翻译
模具术语英文翻译根据国家标准，以下为部分塑料模具成形术语的标准翻译。
动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具术语的标准翻译。
压力铸造模具 Die-Casting Die压铸模零部件定模 Fixed Die Cover Die定模座板 Fixed Clamping Plate定模套板 Bolster Fixed Die动模 Moving Die Ejector Die动模座板 Moving Clamping Plate直流道 Sprue横流道 Runner内浇口 Gate模具分类Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成形Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具Stack Mold, Stack Injection Mould 叠层模Plaster Mold 石膏模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模Forming Die 成型模Progressive Die 连续模Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模Large Die Mold 大型模具Precise Die Mold 精密模具Complex Die Mold 复杂模具Foaming Mould 发泡模具Metal Die 金属模具Plastic Mold 塑料模具Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具Graphite Die 石墨模具流道浇口部分Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆Runner Design 流道设计Main Runner 主流道Secondary Runner 次流道Mould Gate Design 浇口设计Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口，溶渣Insulated Runner Hot Runner 热浇道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）注塑缺陷Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void 缩孔Weld Line 熔接线Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞注塑工艺Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度Tensile Elongation 延伸率Flexural Modulus 弯曲模数Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑机械设备Lathe 车床Planer 刨床Miller Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床, Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具<, /SPAN> Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具常用之工作机械3D Coordinate Measurement 三次元量床Boring Machine 搪孔机CNC Milling Machine CNC铣床Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Copy Lathe 仿形车床Copy Milling Machine 仿形铣床Copy Shaping Machine 仿形刨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Drilling Machine 钻孔机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床Jig Boring Machine 冶具搪孔机Jig Grinding Machine 冶具磨床Lap Machine 研磨机Machine Center 加工制造中心Multi Model Miller 靠磨铣床NC Drilling Machine NC钻床NC Grinding Machine NC磨床NC Lathe NC车床NC Programming System NC程式制作系统Planer 龙门刨床Profile Grinding Machine 投影磨床Projection Grinder 投影磨床Radial Drilling Machine 旋臂钻床Shaper 牛头刨床Surface Grinder 平面磨床Try Machine 试模机Turret Lathe 转塔车床Universal Tool Grinding Machine 万能工具磨床Vertical Machine Center 立式加工制造中心Wire E.D.M 线割放电加工机入水 Gate进入位 Gate Location水口形式 Gate Type大水口 Edge Gate细水口 Pin-point Gate水口大小 Gate Size转水口 Switching Runner Gate唧嘴口径 Sprue Diameter流道 Mold Runner热流道 Hot Runner Hot Manifold温度控制器温控器 Thermostat Thermoregulators Temperature Controller 热嘴冷流道 Hot Sprue Cold Runner唧嘴直流 Direct Sprue Gate圆形流道 Round Full Half Runner流道电脑分析 Mold Flow Analysis流道平衡 Runner Balance热嘴 Hot Sprue热流道板 Hot Manifold发热管 Cartridge Heater探针 Thermocouples插头 Connector Plug插座 Connector Socket密封封料 Seal运水 Water Line喉塞 Line Plug Throat Taps喉管 Tube塑胶管 Plastic Tube快速接头 Jiffy Quick Connector Quick Disconnect Coupling模具零件 Mold Components三板模 3-Plate Mold二板模 2-Plate Mold边钉导边 Leader Pin Guide Pin边司导套 Bushing Guide Bushing中托司 Shoulder Guide Bushing中托边 Guide Pin顶针板 Ejector Retainner Plate托板 Support Plate螺丝 Screw管钉 Dowel Pin开模槽 Ply Bar Scot内模管位 Core Cavity inter-Lock顶针 Ejector Pin司筒 Ejector Sleeve司筒针 Ejector Pin推板 Eject Plate Push Plate Stripper Plate缩呵 Movable Core Return Core Puller扣机（尼龙拉勾） Nylon Latch Lock斜顶 Lifter模胚（架） Mold Base上内模 Cavity Insert下内模 Core Insert行位（滑块） Slide镶件 Insert压座 Wedge耐磨板油板 Wedge Wear Plate压条 Plate撑头 Support Pillar唧嘴 Sprue Bushing挡板 Stop Plate定位圈 Locating Ring锁扣 Latch扣机 Parting Lock Set推杆 Push Bar栓打螺丝 S.H.S.B顶板 Ejector Plate活动臂 Lever Arm分流锥 Sprue Spreader分流板 Spreader Plate水口司 Bush垃圾钉 Stop Pin隔片 Buffle弹弓柱 Spring Rod弹弓 Die Spring中托司 Ejector Guide Bush中托边 Ejector Guide Pin镶针 Pin销子 Dowel Pin波子弹弓 Ball catch喉塞 Pipe Plug锁模块 Lock Plate斜顶 Angle from Pin斜顶杆 Angle Ejector Rod尼龙拉勾 Parting Locks活动臂 Lever Arm复位键提前回杆 Early Return Bar气阀 Valves斜导边 Angle Pin术语 Terms承压平面平衡 Parting Surface Support Balance模排气 Parting Line Venting回针碰料位 Return Pin and Cavity Interference顶针碰运水 Water Line Interferes with Ejector Pin 料位出上下模 Part from Cavith （Core） Side不准用镶件 Do Not Use （Core Cavity） Insert用铍铜做镶件 Use Beryllium Copper Insert初步模图设计 Preliminary Mold Design正式模图设计 Final Mold Design弹弓压缩量 Spring Compressed length稳定性好 Good Stability Stable强度不够 Insufficient Rigidity均匀冷却 Even Cooling扣模 Sticking热膨胀 Thermal Expansion公差 Tolerance铜公（电极） Copper Electrode Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流挡板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom Board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting Lug 铸耳Cavity 模腔模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Joint Pipe Coupler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Inserts 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton Frameworks 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道残料顶销浇道推出杆Sprue Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板Pierce 冲孔Forming 成型（抽凸冲凸）Draw Hole 抽孔Bending 折弯Trim 切边Emboss 凸点Dome 凸圆Semi-Shearing 半剪Stamp Mark 冲记号Deburr or Coin 压毛边Punch Riveting 冲压铆合Side Stretch 侧冲压平Reel Stretch 卷圆压平Groove 压线Blanking 下料Stamp Letter 冲字（料号）Shearing 剪断Tick-Mark Nearside 正面压印Tick-Mark Farside 反面压印Extension Drawing 展开图procedure Drawing 工程图Die Structure Drawing 模具结构图Material 材质Material Thickness 料片厚度Factor 系数Upward 向上Downward 向下Press Specification 冲床规格Die Height Range 适用模高Die Height 闭模高度Burr 毛边Gap 间隙Weight 重量Total Weight 总重量Punch Weight 上模重量Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Cavity 型腔母模Mold Core 模芯公模Taper 锥拔Leather Cloak 仿皮革Shiver 饰纹Flow Mark 流痕Welding Mark 溶合痕Post Screw Insert 螺纹套筒埋值Self Tapping Screw 自攻螺丝Striper Plate 脱料板Piston 活塞Cylinder 汽缸套Chip 细碎物Handle Mold 手持式模具Encapsulation Molding 低压封装成型Two Plate 两极式（模具）Well Type 蓄料井Insulated Runner 绝缘浇道方式Hot Runner 热浇道Runner Plat 浇道模块Valve Gate 阀门浇口Band Heater 环带状的电热器Spindle 阀针Spear Head 刨尖头Slag Well 冷料井Cold Slag 冷料渣Air Vent 排气道Welding Line 熔合痕Eject Pin 顶出针Knock Pin 顶出销Return Pin 回位销反顶针Sleeve 套筒Stripper Plate 脱料板Insert Core 放置入子Runner Stripper Plate 浇道脱料板Guide Pin 导销Eject Rod （Bar）（成型机）顶业捧Subzero 深冷处理Three Plate 三极式模具Runner System 浇道系统Stress Crack 应力电裂Orientation 定向Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）Slag Well 冷料井Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Fan Gate 扇形浇口Dish Gate 因盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Submarine Gate 潜入式浇口Tunnel Gate 隧道式浇口Pin Gate 针点浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口溶渣Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合式模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Bending Die 双折冷弯模具偏移弯曲模Extrusion Die 挤出模Palletizing Die 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runnerless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow（Blow） Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Barreling 滚光加工Belling 压凸加工Bending 弯曲加工Blanking 下料加工Bulging 撑压加工Burring 冲缘加工Cam Die Bending 凸轮弯曲加工Caulking 压合加工Coining 压印加工Compressing 压缩加工Compression Bending 押弯曲加工Crowning 凸面加工Curl Bending 卷边弯曲加工Curling 卷曲加工Cutting 切削加工Dinking 切断蕊骨Double Shearing 叠板裁断Drawing 引伸加工Drawing with Ironing 抽引光滑加工Embossing 浮花压制加工Extrusion 挤制加工Filing 锉削加工Fine Blanking 精密下料加工Finish Blanking 光制下料加工Finishing 精整加工Flanging 凸缘加工Folding 折边弯曲加工Folding 折叠加工Forming 成形加工Impact Extrusion 冲击挤压加工Indenting 压痕加工Ironing 引缩加工Knurling 滚花Lock Seaming 固定接合Louvering 百叶窗板加工MarKing 刻印加工Necking 颈缩加工Notching 冲口加工Parting 分断加工Piercing 冲孔加工Progressive Bending 连续弯曲加工Progressive Blanking 连续下料加工Progressive Drawing 连续引伸加工Progressive Forming 连续成形加工Reaming 铰孔加工Restriking 二次精冲加工矫形锻压Riveting 铆接加工Roll Bending 滚筒弯曲加工Roll Finishing 滚压加工Rolling 压延加工Roughing 粗加工Scrapless Machining 无废料加工Seaming 折弯重叠加工Shaving 缺口修整加工Shearing 切断加工Sizing 精压加工矫正加工Slitting 割缝加工Spinning 卷边旋接Staking 铆固Stamping 锻压加工Swaging 挤锻压加工Trimming 整缘加工Upsetting 锻粗加工顶锻镦粗Wiring 抽线加工Aberration 色差Atomization 雾化Bank Mark 料垄迹印Bite 咬入Blacking Hole 涂料孔（铸疵）Blacking Scab 涂料疤Blister 起泡Blooming 起霜Blow Hole 破孔Blushing 泛白Body Wrinkle 侧壁皱纹Breaking-in 冒口带肉Bubble 膜泡Burn Mark 糊斑Flash Burr 毛边Camber Warpage 翘曲Cell 气泡Center Buckle 表面中部波皱Check 细裂痕Checking 龟裂Chipping 修整表面缺陷Clamp-off 铸件凹痕Collapse 塌陷Color Mottle 色斑Corrosion 腐蚀Crackle 裂痕裂纹Crazing 碎裂Crazing 龟裂Distortion Deformation 变形Edge 切边碎片Edge Crack 裂边Fading 退色Filler Speak 填充料斑Fissure 裂纹Flange Wrinkle 凸缘起皱Flaw 刮伤Flow Mark 流痕Galling 毛边Glazing 光滑Gloss 光泽Grease Pits 污斑Grinding Defect 磨痕Haircrack 发裂Haze 雾度Incrustation 水锈Indentation 压痕Internal Porosity 内部气孔Mismatch 偏模Mottle 斑点Necking 缩颈Nick 割痕Orange peel 橘皮状表面缺陷Overflow 溢流Peeling 剥离Pit 坑Pitting Corrosion 点状腐蚀Plate Mark 模板印痕Pock 麻点Pock Mark 痘斑Resin Streak 树脂流纹Resin Wear 树脂脱落Riding 凹陷Sagging 松垂Saponification 皂化Scar 疤痕Scrap 废料Scrap Jam 废料阻塞Scratch 刮伤划痕Scuffing 深冲表面划伤Seam 裂痕Shock Line 模口挤痕Short Shot 充填不足Shrinkage Pool 凹孔Sink Mark 凹痕Skin Inclusion 表皮折叠Straightening 矫直Streak 条状痕Surface Check 表面裂痕Surface Roughening 橘皮状表皮皱折Surging 波动Sweat Out 冒汗Torsion Distortion 扭曲Warpage 翘曲Waviness 波痕Webbing 熔塌Weld Mark 焊痕Whitening 白化Wrinkle 皱纹Gas Aassisted Technology 气辅Bottle Cap Mold 瓶盖模具。
模具专业词汇中英文对照表
die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow 〔-on〕die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次production control confirmation生产确认checked by初审approved by核准stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工cause description原因说明part number/ P/N 料号item/group/class类别prepared by制表year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim〔wedge〕楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料缺乏nick缺口speck瑕疵shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型〔抽凸,冲凸〕draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字〔料号〕shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板〔顶板〕top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模〔凸模〕feature die公母模female die母模〔凹模〕upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板〔底板〕stripping plate内外打〔脱料板〕outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块〔嵌入件〕deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具〔移转成型用模具〕encapsulation molding低压封装成型〔射出成型用模具〕two plate两极式〔模具〕well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod 〔bar〕〔成型机〕顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销〔拉料杆〕slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道〔sprue less〕无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡沫成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow〔blow〕molding 中空〔吹出〕成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具pro 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising〔embossing〕压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug铸耳cavity 模穴〔模仁〕cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide〔slide core〕滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床pro machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板外表处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊外表austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 外表蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 局部淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 外表硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 著色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 後固化premix 预混料purging 去除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑胶原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CAcellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PApolybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PCpolyethyleneglycol 聚乙二醇PFGpolyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PPpolystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PEpolyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差bite 咬入blacking hole 涂料孔〔铸疵〕blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 外表中部波皱check 细裂痕checking 龟裂chipping 修整外表缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕range peel 橘皮状外表缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化。
锻压专业英文
锻造术语--Terminology of forging（PART I）⏹工厂works：1. 车间shop2. 工作地work flooring3. 工艺设备平面布置layout of manufacturing equipment4. 工位position of work5. 工位器具instruments of position6. 操作工operator7. 辅助工helper8. 剪切工shearing worker9. 操作危险区point of operation10. 模具安装调整工die-setting worker11. 夹紧点pinch point12. 工作面work plane13. 模具库die area14. （原）材料库raw material area⏹一般术语general terms：15. 锻压forging and stamping16. 金属塑性加工plastic working of metal17. 金属压力加工pressworking of metal18. 金属回转加工rotary metalworking19. 热锻hot forging20. 温锻warm forging21. 冷锻cold forging22. 等温锻isothermal forging23. 初次成形加工primary metalworking24. 二次成形加工secondary metalworking25. 成形forming26. 预成形preforming27. 热成形hot working28. 温成形warm working29. 冷成形cold working⏹原材料material:30. 棒料bar31. 热轧棒料black bar32. 拔材drawing bar33. 挤压型材extruded material34. 毛坯，坯料billet35. 废料scrap36. 废料侧边selvedge37. 落料件blank38. 弯曲件bent component39. 杯形件deep-drawn cup40. 剪切件blank41. 高合金钢super alloy steel42. 钛合金Ti-alloy steel43. 镁合金Mg-alloy steel44. 铝合金Al-alloy steel45. 不锈钢stainless steel46. 碳钢carbon steel47. 高碳钢super carbon steel48. 非调质钢49. 结构钢⏹锻件forgings50. 预锻件interstage of the forging51. 终锻件finished forging52. 普通精度锻件commercial tolerance forging53. 精密锻件close tolerance forging54. 自由锻件open die forging55. 模锻件die forgings56. 钢质模锻件steel die forgings57. 冷锻件cold forging58. 冷挤压件cold extrusion59. 冷镦件cold heading60. 辊锻件roll forging⏹锻造forging自由锻open die forging61. 墩粗upsetting（1）局部墩粗local upsetting（2）平砧间墩粗compression between flat platens（3）柳墩mushroom upsetting62. 拔长drawing out（4）芯棒拔长mandrel forging63. 冲孔punching（5）漏孔punching on a supporting64. 扩孔expanding（6）冲头扩孔expanding with a punch（7）马杠扩孔saddle forging（8）楔块扩孔expanding with wedge blocks（9）液压膨胀扩孔hydraulic expanding65. 弯曲bending66. 错移offset67. 扭转twisting68. 切割cutting69. 锻接forging welding70. 压肩necking71. 压痕indentation72. 倒棱chamfering73. 滚圆rolling74. 压钳口tongs hold75. 展宽spreading76. 棒料锻造to forge from a bar77. 调头锻造turn over78. 一火锻造one heat forging79. 两次加热锻造twice heat forging80. 纵向锻造forging with the grain81. 横向锻造forging normal to the grain82. 法兰flange83. 凹挡recess84. 台阶step85. 凸肩hub86. 余面lap87. 余块excess metal88. 钳夹头tong hold89. 黑皮锻件surface as forged90. 中心压实法JTS forging91. RR锻造RR forging92. TR锻造TR forging93. α＋β锻造α＋β forging94. β锻造β forging95. FM锻造FM forging96. 锻件公差forging tolerance97. 锻件基本尺寸nominal dimension of forging98. 锻造比forging ratio99. 送进量feed100. 高径比ratio of height to diameter101. 压缩量reduction模锻die forging102. 开式模锻closed-die forging103. 有飞边模锻impressiondie forging104. 闭式模锻，无飞边模锻no-flash (flashless) die forging 105. 多向模锻multi-ram forging106. 精密锻造precision forging（10）闭塞锻造core forging（11）高速锻造high velocity forging process（12）复合锻造duplex forging（13）伞齿轮锻造forged bevel gear107. 制坯工序preforming（14）液压工步gathering（15）体积分配volume distribution108. 预锻preforging109. 终锻finish-forging110. 精压sizing111. 终锻模校正restriking112. 上充upward displacement113. 锻件图forging drawing（16）冷锻件图cold forging drawing（17）热锻件图hot forging drawing（18）横截面线图cross section drawing114. 锻件圆角roundness of machine parts (forgings) 115. 模锻斜度draft angle116. 盲孔non-penetrated hole117. 连皮wad118. 飞边flash（19）分模线parting line（20）飞边厚度flash thickness119. 胎模锻loose tooling forging120. 试锻trial forging（21）试锻检验trial forging inspection121. 单坯锻造to forge from a billet122. 一锻多件multiple forging123. 机械加工余量machining allowance124. 加工精度forming accuracy（22）模锻件精度accuracy of die forging125. 材料利用率stock utilization126. 脱模die releasing127. 换模die change128. 锻件设计design of forgings129. 锻造方案forging design130. 锻造批量forging lot quantity131. 多品种少批量生产multi-kind small lot production 153 WORDS IN TOTAL。
最全的模具词汇 中英文对照
assemble mould合箱assembling mould装配铸型baked mould干型bar mould多穴压模big-end-up mould上大下小钢锭模black mould of rice 黑变病blank mould turnover 雏型模翻转blowing mould吹模blue mould of citrus 柑桔青霉病cap mould压顶线脚car type mould conveyor 小车式铸型输送机case mould plaster 母模用石膏casting mould铸型centrifugal casting mould离心铸造铸型ceramic mould casting 陶瓷模注法channel mould槽模chill mould冷铸型(模)close mould封闭铸型close mould (铸造用) 合箱closed mould闭式模; 闭式压模cold-punching mould冷冲模collapsible mould分室模composite ceramic mould复合陶瓷型composite mould casting 复合型铸造copper mould base 铜模底copper mould wall 铜坩埚壁corrugated mould波形铸模cover mould压缝线脚covered floor mould盖箱地面铸型cylinder mould machine 圆网造纸机double-mould-broad ridging plough 双壁起垄犁draw mould薄壁模子driel mould干型drip mould滴水线脚dry sand mould干型ear mould耳模electric pole mould hanger 电杆模型吊架end mould端模Erical mould可压锭模; 挤压锭模evacuated mould空腔模face mould面模fall wheat snow mould冬小麦雪霉病falling mould曲型线条female mould阴模fixed mould固定模flaskless mould无箱铸型floating-point mould浮点模型floor mould地铸模fluted mould波形模foam sponge mould泡沫胶硫化模footed mould压印底圈的模型forging mould锻模front mould前模full-mould casting process 实型铸造gang mould成组模; 成组模板garden mould园土get in the mould垫平铸型glass mould玻璃型; 玻璃铸型glass mould diode 玻璃模二极管graphite mould石墨型grass mould腐草土gray mould灰霉green mould绿霉病green mould of citrus 柑桔绿霉病ground mould地面铸型; 堆土木模gypsum mould石膏型hair mould毛霉hair mould sprout 毛霉芽half mould半型hoist for mould board carrier 模板车升降机hump mould压坯用阳模ice mould冰铸ingot mould钢锭模; 铸锭模; 铸锭型; 锭模ingot mould milling machine 钢锭模铣床ingot slab mould扁钢锭模insulating mould coating 隔热涂料integral mould整模型invested mould熔模铸型iron mould铁锈迹leaf mould叶霉; 腐叶土loam mould泥型lower mould half 下模; 凹模male mould凸模; 阳模master mould母型; 原模mismatch in mould铸型错箱mould印模; 模; 模板; 模具; 模筛样板; 模塑; 模子; 成型模具; 圆网; 造型模板; 塑模; 霉; 霉病; 霉菌; 纸型mould addition 钢锭模添加剂mould and die milling machine 模具铣床mould assembling 合箱mould assembling and closing 铸型合箱mould assembly 合型mould blower 吹型机mould board 造型板; 样板mould boardless plough 无壁犁mould buggy 钢锭模车mould case 模制壳mould clamp 卡具mould clamps 模型紧固夹mould cleaner 模具清洁剂mould closer 合箱机; 合箱装置mould coating material 钢锭模涂料mould core 模芯mould cover 腐殖质层mould cure 模塑硫化; 模型硫化mould dam aged sweet potato poisoning 黑斑甘薯中毒mould dimension 铸型尺寸mould drag 下半箱mould drying 铸型烘干mould efficiency 模塑效率mould emptier 脱模机构mould erosion 铸型冲蚀mould facing 涂料mould fitter 合箱工mould flat gauge 样板mould form 模型型腔mould fungus 霉菌mould growth test 长霉试验mould half 半型mould hardness 铸型硬度mould impression 模型内腔; 模型型腔; 模穴mould in a snap flask 无箱造型mould in the pit 地坑造型mould inoculation 型内孕育mould jacket 型套mould kernel 模芯mould life 模型寿命mould lifting 铸型起模mould lining 坩埚衬里mould loft 放样间mould loft floor 放样台mould lofter 放样工; 放样工人mould loftsman 放样工; 放样工人mould machine 模塑机mould machine of cereal seed selection 谷物选种机mould mark 模缝条痕mould matrix cathode 模制阴极mould oil 脱模油mould on end 垂直分型造型mould pig iron 型铁mould plaster 模型用石膏mould plate 模型板mould plunger 阳模mould plunger force plug 凸模mould preparation bay 钢锭模准备跨mould press 模压机mould pressing 旋压成形mould proofing 防霉mould rains 梅雨mould release 分型粉mould relese 脱模mould rollover unit 翻箱装置mould sand 型砂mould seam 模缝mould setting-and-stripping bay 钢锭模准备和脱锭跨mould shift 错箱mould shrinkage 模内收缩; 模压收缩; 脱模后的收缩mould splits 模组分mould stripping 铸型起模; 拆模mould susceptibility 感霉性mould test chamber 霉菌试验箱mould train 模组mould turnover 翻箱mould unloading 出模; 脱模; 卸模mould veining 铸型裂纹mould vibrator 模板振动器mould vulcanization 模塑硫化mould wash 脱模涂料mould wash mixer 涂料搅拌机multiple cavity mould多型腔铸型; 多巢模multiple mould多件石膏模multiple-part mould多箱铸型needle mould针模one-piece mould整体铸型open bottom mould底开式钢锭模open mould明浇铸型; 敞口铸型open sand mould明浇砂型optical instrument mould and fog auto-detector 光学仪器霉雾自动检测仪ornamental mould艺术造型pallet conveyer mould machine 滑板输送式造型机paper mould纸型paste mould衬碳模paste mould ware 衬碳模成形的制品peat mould泥炭土permanent mould永久铸型pig mould锭模plural mould operation 多模操作porous mould多孔模型positive mould阳模; 阳压模press mould压模press mould ware 模压器皿pressing mould压模process of unconventional heat treatment of mould模具非常规热处理工艺quadrant mould四开木压条real mould实模型rectal suppository mould肛门栓剂模refractory shell mould耐火材料壳型removal of the mould拆模reverse mould倒模; 倒型revesing permanent mould双面金属型ring mould瓶颈模ring-shaped mould环型铸模risk of mould发霉险roast sand mould干砂型rubber mould橡胶皮模running mould模筛样板; 模饰样板saccharifying mould糖化霉sealing of a mould铸型密封section mould型模sectional mould镶合砂型semi-automatic mould半自动模; 半自动塑模semi-chilled mould casting 半金属型铸造; 半冷模铸造semi-permanent mould半永久型; 半永久性模semiclosed top mould半封顶锭模shell mould machine 壳型造型机shiftable mould-board 可拆换的刀片sign mould符号模型single cavity mould整体铸型single mould单件模型skin dried mould面干铸型skin drying mould表干型sleeper steel mould轨枕钢模slime mould粘菌slip flask mould脱箱铸型snap flask mould活箱造型; 无箱铸型snapflask mould脱箱造型snow mould雪霉病; 雪疫病soap mould皂模sooty mould烟霉; 煤污病sooty mould of rice plant 水稻煤病sooty mould of tea 茶叶煤污病spacing mould隔膜split mould对开模stagnant mould不动模型standard steel ingot mould标准钢锭模steel mould钢锭模; 钢模steel mould for electric pole 电杆钢模stock mould定型模stripper-plate mould脱模板塑模sweeping loam mould刮泥型swell of a mould胀砂symbol mould符号模型tape of mould模型锥度thin-walled metal mould薄壁金属型thin-walled mould薄壁结晶器three-cavity mould三开箱铸型tilt-mould billet 可倾模锭坯tire recapping mould轮胎翻修硫化机tomato leaf mould番茄叶霉病top mould half 凸模two-cavity mould双型腔铸型variable-point-mould变点模型vegetable mould腐殖土verge mould山墙檐口线脚waste mould gypsum 废模石膏watch-case mould表壳式压模water mould水霉wood casting mould木质铸造模型X-mould machine 多模成型机。
模具专业词汇中英文对照表
模具专业词汇中英文对照表1. 模具材料（Mould Materials）•合金钢（Alloy Steel）•不锈钢（Stnless Steel）•工具钢（Tool Steel）•铸造铁（Cast Iron）•铝合金（Aluminum Alloy）•铜合金（Copper Alloy）•硅橡胶（Silicone Rubber）•塑料（Plastic）•陶瓷（Ceramic）2. 模具零件（Mould Components）•模板（Mold Base）•注塑装置（Injection Unit）•顶出器（Ejector）•气嘴（Nozzle）•间隙（Clearance）•提位器（Lifter）•滑块（Slide）•定位圈（Locating Ring）•膜背（Backing Plate）•挡块（Stop Block）•压板（Clamp Plate）•冷却管（Coolant Pipe）•驱动装置（Drive Unit）3. 模具制造工艺（Mould Manufacturing Process）•设计（Design）•切割（Cutting）•加工（Machining）•组装（Assembly）•调试（Debugging）•精修（Finishing）•表面处理（Surface Treatment）•检查（Inspection）•试产（Trial Production）4. 模具加工方式（Mould Processing Methods）•铣削（Milling）•磨削（Grinding）•拉刀（Planing）•镗削（Boring）•钻孔（Drilling）•线切割（Wire Cutting）•抛光（Polishing）•火花加工（EDM）5. 模具设计要点（Key Points in Mold Design）•壁厚（Wall Thickness）•浇注系统（Gating System）•冷却系统（Cooling System）•排气（Venting）•气罩（Bubbler）•顶杆（Ejector Pin）•脱模斜度（Draft Angle）•零件坯料与尺寸（Blank and Dimensions）•对位方式（Alignment Method）•衬套（Insert）•翻制（Flip Mold）•分模（Split Mold）6. 模具维护与保养（Mold Mntenance）•模具清洁（Mold Cleaning）•润滑（Lubrication）•排浆（Purging）•磨损修复（Wear Repr）•抛光修复（Polish Repr）•零件更换（Component Replacement）•修复记录（Repr Record）•数字化管理（Digital Management）7. 模具常见故障及解决方法（Common Mold Faults and Solutions）•翘曲（Warping）•缺陷（Defects）•泛油（Flash）•磨损（Wear）•烧坏（Burning）•掉件（Part Ejection）•插损（Insert Damage）以上仅是模具专业领域常用词汇的一个简单对照表。
模具技术相关术语 英汉对照(汇总)
模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding挤出成形shell casting 壳模铸造foam forming发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料销spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分厘卡interferometer 干涉仪leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一吋monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶迭熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIGb 熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 着色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 后固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑料片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑料原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑料epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EV A ethylene-vinlacetate copolyme 醋酸乙烯共聚物EV A expanded polystyrene 发泡聚苯乙烯EPS fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑料polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PV AC polyvinylalcohol 聚乙烯醇PV A polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 硅树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑料unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁钻arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手计算机关联用语3D modeling 三次元模拟access 通路animation 卡通影片application 应用board 基板bug 故障bus 总线CAD 计算机辅助设计CAE 计算机辅助工程分析CAM 计算机辅助制造cassette卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 计算机copy 复制cursor 游标curve modeling 曲面仿真database 数据库design 设计digitizing 数字化disk 磁盘dot 点eyelet 眼孔floppy 磁盘片format 格式化graphic 圆解hardware 硬件honeycomb 蜂巢interface 界面know how 秘诀laser printer 激光打印机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling 造型module 模块monitor 屏幕mouse 鼠标need 需求network 网络new version 新版on line 上线中option 选择PC 个人计算机plotter 绘图机program 程序scanning 扫描simulation 仿真software 软件solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 字处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工caulking 铆合加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 迭板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 折迭加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重迭加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边铆接staking 铆固stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat 铆合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼后熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆栈拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸除机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 后角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze 钨青铜waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼后熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件模具加工方法barrel 滚筒(加工) bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验normal distribution 常态分配ozone resistance test 抗臭氧试验pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shore hardness 萧氏硬度spiral flow test 螺旋流动试验surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机tensile impact test 拉伸冲击试验tensile strength 抗拉强度tension test 张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验weatherometer 人工老化试验机weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮Al2O3 氧化铝balance 平衡bond 结合borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目parameter 参数resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转机械设计及周边其他用语assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重复载荷riveted joint 铆钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割业务与贸易关连用语accept order 接受订货account 账户after service 售后服务amendment 修正annual sales 年销售额at sight 见票即付balance 余额bank draft 汇票bargain goods 廉价品batch 批次bid 出价bid sales 投标买卖bill of landing 提单bills receivable 应收票据brand 品牌bulk cargo 散装货business transaction 商业交易buyer 买方carbon copy 打字副本cargo collection 揽货carton 纸箱cash in advance 预付现金catalogue 型录cheque 支票CLF 运费保险费在内价格claim 索赔clearance goods 清仓品commision 佣金commission 批发商complain 抱怨container 货柜correspondence bank 往来银行cost 成本cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单D/P 付款交单deferred payment 分期付款deferred shipment 分期装运delivery on spot 当场交货delivery time 交期delivery order 交货单discount 折扣discount on draft 贴现documentary draft 跟单汇票down payment 订金enclosure 附件endorsement 背书enquete 调查exhibition 展览会export 出口factory visiy 工厂参观favourable price 合宜价格foreign exchange 外汇free on board 船上交货价idea price 希望价格import 进口Japanese Industrial 日本工业规格invoice 发票L/C 信用状margin 利润market 市价net weight 净重no payment 拒绝付款odd item 零头offer 报价open account 交互计算order 订单over looked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格payment method 付款方式port of destination 目地港port of trans-shipment 转口港price 价格price decending 减价price rising 涨价procurement 采办prompt delivery 实时交货purchase 购入purchasing agent 采购代理商quotation 报价单。
锻模术语中英文对照表
锻模术语中英文对照表锻模术语中英文对照表1、锻模forging die模锻时使坯料成形而获得锻件的2、开式锻模open forging die金属流动不完全受模膛限制的模具3、闭式锻模closed forging die金属流动完全受模膛限制的模具4、锤锻模hammer forging die在模锻锤上使坯料成形为模锻件或其半成品的模具5、机械压力机锻模(或简称机锻模）mechanical press forging die 在机械压力机上使坯料成形为模锻件或其半成品的锻模6、平锻模upset forging die在水平锻造机上使坯料成形为模锻件或其半成品的模具7、辊锻模forge rolling die在辊锻机上将毛坯纵轧成形的扇形模具8、螺旋压力机锻模screw perss die在螺旋压力机上使坯料成形为模锻件或其半成品的模具9、冷镦模cold heading die在冷镦机上使坯料切断、预成形、成形为冷成形件的模具10、高速锤锻模high speed hammer forging die在高速锤上使坯料成形为模锻件的模具11、校正模suraightening die用于校正已成形的锻件成为准确的形状和尺寸的模具12、压印模coining die使锻件表层变形产生凹凸印纹的模具13、切边模trimming die切除锻件飞边的模具14、冲孔模piercing die切除孔内连皮等使锻件具有透孔的模具15、挤压模extrusion die使金属挤压成形的模具16、精锻模precision forging die锻制精密锻件的模具。
精密模锻件是指在形状尺寸精度方面高于普通模锻件的锻件17、精压模sizing die对锻件进行少量压缩，以提高锻件局部或整体的尺寸精度的模具18、多向锻模multi-ram forging die能从垂直和水平（或倾斜）方向分别或同时对金属毛坯施加压力，使毛坯能多向成形的模具19、闭塞锻模core forging die具有锻件外轮廓形状的模膛先闭合,然后将冲头压进模膛内部，使金属充满模膛同时冲出锻件孔部所用模具20、胎膜loose tooling在自由锻设备上锻造模锻件时使用的模具21、锻模模块forging die block模锻时承受某一变形工步全部锻击力并带有工作部分的模具主体22、锻模镶块forging die insert对锻模的复杂或易损工作部分单独分开制造，然后镶入模块的零件23、飞边槽flash cave在分模面沿模膛周边设置的、用于保证模膛充满和容纳在成形过程中产生多余材料的凹槽,它由飞边桥和飞边仓组成24、飞边桥flash land飞边槽中和模膛紧相连接的间隙面，多余金属越过该间隙面挤出而形成飞边，它可产生阻力使金属充满模膛25、飞边仓cutter or flash gutter围绕着飞边桥外周的凹槽，用于容纳多余的金属材料26、阻力沟resistance slot在飞边桥部或在模膛难充满处的外边沿垂直于金属流动方向局部设置的小沟槽。
模具术语翻译
模具名词中英文对照表序号中文名英文名1 一、水口gate2 进水位gate location3 水口形式gate type4 大水口edge gate5 细水口 pin-point gate6 水口大小gate size7 转水口switching gate8 唧嘴口径sprue diameter9 二、流道runner10 热流道hot runner11 冷流道cold runner12 唧嘴直流direct sprue gate13 圆形流道round runner14 模流分析mold flow analysis15 流道平衡runner balance16 热嘴hot sprue17 热流道板hot manifold18 发热管cartridge heater19 探针thermocouples20 插头connector plug21 插座 connector socket22 密封/封料 seal23 三、运水water line24 喉塞line pug25 喉管tube26 塑胶管plastic tube27 快速接头jiffy quick connector plug28 四、模具零件mold components29 三板模three-plate mold模具名词中英文对照表序号中文名英文名30 二板模two-plate mold31 边钉/导边leader pin/guide pin32 边司/导套bushing/guide bushing33 顶针板ejector retainer plate34 托板support plate35 螺丝 screw36 管钉dowel pin37 开模槽ply bar score38 内模管位core/cavity inter-lock39 顶针ejector pin40 司筒ejector sleeve41 司筒针ejector pin42 推板stripper plate43 缩呵movable core44 扣机（尼龙拉勾） nylon latch lock45 斜顶lifter46 模胚（架） mold base47 母模cavity insert48 公模core insert49 行位（滑块） slide50 镶件insert51 压座/斜鸡wedge52 耐磨板/油板wedge wear plate53 压条plate54 撑头support pillar55 唧嘴 sprue bushing56 挡板stop plate57 定位圈locating ring58 锁扣latch模具名词中英文对照表序号中文名英文名59 扣鸡parting lock set60 推杆push bar61 栓打螺丝S.H.S.B62 顶板ejector plate63 活动臂lever arm64 水口司bush65 垃圾钉stop pin66 隔片buffle67 弹弓柱spring rod68 弹弓die spring69 镶针pin70 销子dowel pin71 波子弹弓ball catch72 喉塞pipe plug73 锁模块lock plate74 斜顶angle from pin75 斜顶杆angle ejector rod76 尼龙拉勾parting locks77 复位键、提前回杆early return bar78 气阀valves79 斜导边angle pin80 模排气parting line venting81 模总高超出啤机规格mold base shut height82 模胚原身出料位cavity direct cut on A-plate，coredirect cut on B-plate.83 不准用镶件Do not use (core/cavity) insert84 用铍铜做镶件use beryllium copper insert85 强度不够insufficient rigidity86 公差tolerance87 铜公(电极) copper electrode动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具术语的标准翻译。
模具常用中英词汇
各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻pressforging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubbermolding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shellcasting 壳模铸造foam forming 发泡成形sinterforging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow> molding 中空(吹出>成形 squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gatemold 复式浇口模具expander die 扩径模offset bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模 porousmold 通气性模具duplicated cavity plate 复板模positivemold 全压式模具fantail die 扇尾形模具pressuredie 压紧模fishtail die 鱼尾形模具profiledie 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具prototypemold 雏形实验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing> 压花起伏成形re-entrant mold 倒角式模具 sectionaldie 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流檔板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 扥架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁>cavity retainer plate 模穴扥板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出杆ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘销flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧销goose neck 鹅颈管 guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶镦冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶销lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑料模座 mold clamp 铸模紧固夹mold platen 模用板 moving bolster 换模保持装置moving bolster plate 可动侧模板 one piece casting 整体铸件parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导销pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 扥料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口 slide(slide core> 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套 sprue bushing guide 注道导套sprue lock bushing 注道定位衬套 sprue puller 注道拉料销spue line 合模线 square key 方键square nut 方螺帽 square thread 方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱销 stripper bolt 脱料螺栓stripper bushing 脱模衬套 stripper plate 剥料板stroke end block 行程止梢 submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 扥板 sweep templete 造模刮板tab gate 辅助浇口 taper key 推拔键taper pin 拔锥梢/锥形梢 teeming 浇注three start screw 三条螺纹 thrust pin 推力销tie bar 拉杵 tunnel gate 隧道形浇口vent 通气孔 wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床 boring machine 搪孔机cnc milling machine CNC铣床 contouring machine 轮廓锯床copy grinding machine 仿形磨床 copy lathe 仿形车床copy milling machine 仿形铣床 copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床 die spotting machine 合模机drilling machine 钻孔机 engraving machine 雕刻机engraving E.D.M. 雕模放置加工机 form grinding machine 成形磨床graphite machine 石墨加工机 horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心 internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机 jig grinding machine 冶具磨床lap machine 研磨机 machine center 加工制造中心multi model miller 靠磨铣床 NC drilling machine NC钻床NC grinding machine NC磨床 NC lathe NC车床NC programming system NC程序制作系统 planer 龙门刨床profile grinding machine 投影磨床 projection grinder 投影磨床radial drilling machine 旋臂钻床 shaper 牛头刨床surface grinder 平面磨床 try machine 试模机turret lathe 转塔车床 universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心 wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机 bench comparator 比长仪block gauge 块规 bore check 精密小测定器calibration 校准 caliper gauge 卡规check gauge 校对规 clearance gauge 间隙规clinoretee 测斜仪 comparator 比测仪cylinder square 圆筒直尺 depth gauge 测深规dial indicator 针盘指示表 dial snap gauge 卡规digital micrometer 数字式测微计 feeler gauge 测隙规gauge plate 量规定位板 height gauge 测高规inside calipers 内卡钳 inside micrometer 内分厘卡interferometer 干涉仪 leveling block 平台limit gauge 限规 micrometer 测微计mil 千分之一吋 monometer 压力计morse taper gauge 莫氏锥度量规 nonius 光标卡尺optical flat 光学平晶 optical parallel 光学平行passimeter 内径仪 position scale 位置刻度profile projector 轮廓光学投影仪 protractor 分角器radius 半径 ring gauge 环规sine bar 正弦量规 snap gauge 卡模square master 直角尺 stylus 触针telescopic gauge 伸缩性量规 working gauge 工作量规模具钢材alloy tool steel 合金工具钢 aluminium alloy 铝合金钢bearing alloy 轴承合金 blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢clad sheet 被覆板 clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金 meehanite cast iron M汉纳铸钢meehanite metal M汉纳铁 merchant iron 市售钢材molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢nickel chromium steel 镍铬钢 prehardened steel 顶硬钢silicon steel sheet 硅钢板 stainless steel 不锈钢tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜troostite 吐粒散铁 tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板表面处理关连用语age hardening 时效硬化 ageing 老化处理air hardening 气体硬化 air patenting 空气韧化annealing 退火 anode effect 阳极效应anodizing 阳极氧化处理 atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火 austenite 奥斯田体/奥氏体bainite 贝氏体 banded structure 条纹状组织barrel plating 滚镀 barrel tumbling 滚筒打光blackening 染黑法 blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理 box annealing 箱型退火box carburizing 封箱渗碳 bright electroplating 辉面电镀bright heat treatment 光辉热处理 bypass heat treatment 旁路热处理carbide 炭化物 carburized case depth 浸碳硬化深层carburizing 渗碳 cementite 炭化铁chemical plating 化学电镀 chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化 coating 涂布被覆cold shortness 低温脆性 comemtite 渗碳体controlled atmosphere 大气热处理 corner effect 锐角效应creeping discharge 蠕缓放电 decarburization 脱碳处理decarburizing 脱碳退火 depth of hardening 硬化深层diffusion 扩散 diffusion annealing 扩散退火electrolytic hardening 电解淬火 embossing 压花etching 表面蚀刻 ferrite 肥粒铁first stage annealing 第一段退火 flame hardening 火焰硬化flame treatment 火焰处理 full annealing 完全退火gaseous cyaniding 气体氧化法 globular cementite 球状炭化铁grain size 结晶粒度 granolite treatment 磷酸溶液热处理graphitizing 石墨退火 hardenability 硬化性hardenability curve 硬化性曲线 hardening 硬化heat treatment 热处理 hot bath quenching 热浴淬火hot dipping 热浸镀 induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化 ion carburizing 离子渗碳处理ion plating 离子电镀 isothermal annealing 等温退火liquid honing 液体喷砂法 low temperature annealing 低温退火malleablizing 可锻化退火 martempering 麻回火处理martensite 马氏体/硬化铁炭 metallikon 金属喷镀法metallizing 真空涂膜 nitriding 氮化处理nitrocarburizing 软氮化 normalizing 正常化oil quenching 油淬化 overageing 过老化overheating 过热 pearlite 针尖组织phosphating 磷酸盐皮膜处理 physical vapor deposition 物理蒸镀plasma nitriding 离子氮化 pre-annealing 预备退火precipitation 析出 precipitation hardening 析出硬化press quenching 加压硬化 process annealing 制程退火quench ageing 淬火老化 quench hardening 淬火quenching crack 淬火裂痕 quenching distortion 淬火变形quenching stress 淬火应力 reconditioning 再调质recrystallization 再结晶 red shortness 红热脆性residual stress 残留应力 retained austenite 残留奥rust prevention 防蚀 salt bath quenching 盐浴淬火sand blast 喷砂处理 seasoning 时效处理second stage annealing 第二段退火 secular distortion 经年变形segregation 偏析 selective hardening 部分淬火shot blast 喷丸处理 shot peening 珠击法single stage nitriding 等温渗氮 sintering 烧结处理soaking 均热处理 softening 软化退火solution treatment 固溶化热处理 spheroidizing 球状化退火stabilizing treatment 安定化处理 straightening annealing 矫直退火strain ageing 应变老化 stress relieving annealing 应力消除退火subzero treatment 生冷处理 supercooling 过冷surface hardening 表面硬化处理 temper brittleness 回火脆性temper colour 回火颜色 tempering 回火tempering crack 回火裂痕 texture 咬花thermal refining 调质处理 thermoechanical treatment 加工热处理time quenching 时间淬火 transformation 变态tufftride process 软氮化处理 under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化 vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火 vacuum heat treatment 真空热处理vacuum nitriding 真空氮化 water quenching 水淬火wetout 浸润处理焊接用语acetylene 乙炔 ampere 电流安培angle welding 角焊 arc 电弧argon arc welding 氩弧焊接 bare electrode 光熔接条butt welding 对接焊接 camber 电弧弯曲cascade 阶叠熔接法 clad weld 被覆熔接crator 焊疤 excess metal 多余金属filler rod 焊条 fillet weld 填角焊接gas shield 气体遮蔽 groove welding 起槽熔接hand face shield 手握面罩 hard facing 硬表面堆焊jig welding 工模焊接 laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接 nugget 点焊熔核overlaying 堆焊 peening of welding 珠击熔接法plug welding 塞孔熔接 positioned welding 正向熔接pressure welding 压焊 propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条 reinforcement of weld 加强焊接resist 抗蚀护膜 root running 背面熔接seam 焊缝 seaming 接合seam welding 流缝熔接 series seam welding 串联缝熔接skip welding process 跳焊法 spark 火花spot welding 点焊接 stitch welding 针角焊接stud arc welding 电弧焊接 under laying 下部焊层void 焊接空隙 weld flow mark 焊接流痕weld flush 焊缝凸起 weld line 焊接纹weld mark 焊接痕 weld penetration 熔接透入weld zone 焊接区 welding 焊接welding bead 焊接泡 welding direction 焊接方向welding distortion 焊接变形 welding flux 焊剂welding ground 电熔接地 welding interval 焊接周期welding stress 熔接应变 welding torch 熔接气炬射出成形关联用语activator 活化剂 bag moulding 气胎施压成形bonding strength 粘合强度 breathing 排气caulking compound 填隙料 cell 气孔cold slug 半凝式射出 colorant 着色剂color matching 调色 color masterbatch 色母料compound 混合料 copolymer 共聚合体cull 残料废品 cure 凝固化cryptometer 不透明度仪 daylight 开隙dry cycle time 空料试车周期时间 ductility 延性elastomer 弹性体 extruded bead sealing 压出粒涂层法feed 供料 filler 充填剂film blowing 薄膜吹制法 floating platen 活动模板foaming agent 发泡剂 gloss 光泽granule 颗粒料 gunk 料斗hot mark 热斑 hot stamping 烫印injection nozzle 射出喷嘴 injection plunger 射出柱塞injection ram 射出冲柱 isomer 同分异构物kneader 混合机 leveling agent 匀涂剂lubricant 润滑剂 matched die method 配合成形法mould clamping force 锁模力 mould release agent 脱模剂nozzle 喷嘴 oriented film 取向薄膜parison 吹气成形坏料 pellet 粒料plasticizer 可塑剂 plunger 压料柱塞porosity 孔隙率 post cure 后固化premix 预混料 purging 清除reciprocating screw 往复螺杆 resilience 回弹性resin injection 树脂射出法 rheology 流变学sheet 塑料片 shot 注射shot cycle 射出循环 slip agent 光滑剂take out device 取料装置 tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板 transparency 透明性void content 空洞率塑料原料acrylic 压克力 casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CABcomposite material 复合材料 cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯 disperse reinforcement 分散性强化复合材料engineering plastics 项目塑料 epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素 ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVAethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA expanded polystyrene 发泡聚苯乙烯EPSfiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MFnitrocellulose 硝酸纤维素 phenolic resin 酚醛树脂plastic 塑料 polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETPpolymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯 polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDCprepolymer 预聚物 silicone resin 硅树脂thermoplastic 热塑性 thermosetting 热固性thermosetting plastic 塑料 unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差 atomization 霚化bank mark 滞料纹 bite 咬入blacking hole 涂料孔(铸疵> blacking scab 涂料疤blister 起泡 blooming 起霜blow hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷 color mottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑 resin streak 树脂流纹resin wear 树脂脱落 riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞 scratch 刮伤/划痕scuffing 深冲表面划伤 seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕skin inclusion 表皮折叠 straightening 矫直streak 条状痕 surface check 表面裂痕surface roughening 橘皮状表皮皱折 surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手 angle cutter 角铣刀anvil 铁钻 arbour 心轴backing 衬垫 belt sander 带式打磨机buffing 拋光 chamfering machine 倒角机chamfering tool 去角刀具 chisel 扁錾chuck 夹具 compass 两角规concave cutter 凹面铣刀 convex cutter 凸形铣刀cross joint 十字接头 cutting edge clearance 刃口余隙角drill stand 钻台 edge file 刃用锉刀file 锉刀 flange joint 凸缘接头grinder 砂轮机 hammer 铁锤hand brace 手摇钻 hatching 剖面线hexagon headed bolt 六角头螺栓 hexagon nut 六角螺帽index head 分度头 jack 千斤顶jig 治具 kit 工具箱lapping 研磨 metal saw 金工锯nose angle 刀角 pinchers 钳子pliers 铗钳 plug 柱塞头polisher 磨光器 protable driller 手提钻孔机punch 冲头 sand paper 砂纸scraper 刮刀 screw driver 螺丝起子scribing 划线 second out file 中纹锉spanner 扳手 spline broach 方栓槽拉刀square 直角尺 square sleeker 方形镘刀square trowel 直角度 stripping 剥离工具模具基本零件1﹕模具零件模具零件名称中英文对照一览表零件名称ENGLISH NAME 零件名称ENGLISH NAME上固定板TOP CLAMPING PLATE 母模仁CAVITY母模板CAVITY PLATE 公模仁CORE公模板CORE PLATE 母模入子CAVITY INSERT模脚SUPPRORT BLOCK 母模心子CAVITY INSERT PIN上顶出板EJECTOR RET PLATE 母模替换入子CAVITY CHANGEABLEINSERT下顶出板EJECTOR PLATE 公模入子CORE INSERT下固定板BOTTOM CLAMPING PLATE 公模心子CORE INSERT PIN隔热板THERMAL INSULATING PLATE 公模替换入子CORE CHANGEABLE INSERT 脱料板RUNNER STRIPPER PLATE 滑块入子SLIDE INSERT母模垫板CAVITY SUPPORT PLATE 滑块心子SLIDE INSERT PIN公模垫板CORE SUPPORT PLATE 斜销入子ANLGE LIFTER INSERT脱料板STRIPPER PLATE 斜销心子ANLGE LIFTER PIN流道板RUNNER PLATE 流道开关RUNNER SHUT OFF零件名称ENGLISH NAME 零件名称ENGLISH NAME定位环LOCATING RING T 形块T GIB注口衬套SPRUE BUSHNG U 形块U GIB导柱LEADER PIN 拉料销SPRUE PULLER PIN导套LEADER BUSHING 定位销DOWEL PIN顶板导柱GUIDE PIN 顶针EJECTOR PIN顶板导套GUIGE BUSHING 扁销RECTANGLE EJECTOR PIN 大拉杆LARGE PULLER PIN 套筒EJECTOR SLEEVE小拉杆SMALL PULLER PIN 顶出块EJECTOR BLOCK支撑柱SUPPORT PILLAR 斜销ANGLE LIFTER定位块INTERLOCKS 斜销座ANGLE LIFTER BASE定位柱LOCATION PILLAR 引导块GUIDE BLOCK开闭器(塑料型> FRICTIONAL PULLER弹簧SPRING 零件名称ENGLISH NAME运输板PL LOCK O 形环O RING冷却棒THERMAL PIN零件名称ENGLISH NAME 止水塞BRASS PRESSURE PLUG 滑块SLIDE 隔水板STRAIGHT BUFFLE滑块座SLIDE BASE 水管接头JIFFY TYTE PLUG滑轨SLIDE RAIL 油封OIL SEAL后跟块HELL BLOCK 内六角螺钉SOCKET HEAD CAP SCREW耐磨板WEAR BLOCK 等高螺钉SOCKET HEAD STRIPPER BLOT压板RAIL 吊模螺丝EYE BLOT限位块STOP BLOCK 吊环SAFETY HOIST RINGS 定位夹SLIDE RETAINER 弹簧垫圈SPRING WASHER定位珠SLIDE RETAINER 加长型水管接头EXTENSION JIFFY TYTEPLUG急回机构POSITIVE EARLY EJECTOR RETURN急回推杆LEVER固定块MOUNT AND COVER PLATE 弹簧片ARM。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
锻模术语中英文对照表锻模术语中英文对照表1、锻模forging die模锻时使坯料成形而获得锻件的2、开式锻模open forging die金属流动不完全受模膛限制的模具3、闭式锻模closed forging die金属流动完全受模膛限制的模具4、锤锻模hammer forging die在模锻锤上使坯料成形为模锻件或其半成品的模具5、机械压力机锻模（或简称机锻模）mechanical press forging die 在机械压力机上使坯料成形为模锻件或其半成品的锻模6、平锻模upset forging die在水平锻造机上使坯料成形为模锻件或其半成品的模具7、辊锻模forge rolling die在辊锻机上将毛坯纵轧成形的扇形模具8、螺旋压力机锻模screw perss die在螺旋压力机上使坯料成形为模锻件或其半成品的模具9、冷镦模cold heading die在冷镦机上使坯料切断、预成形、成形为冷成形件的模具10、高速锤锻模high speed hammer forging die在高速锤上使坯料成形为模锻件的模具11、校正模suraightening die用于校正已成形的锻件成为准确的形状和尺寸的模具12、压印模coining die使锻件表层变形产生凹凸印纹的模具13、切边模trimming die切除锻件飞边的模具14、冲孔模piercing die切除孔内连皮等使锻件具有透孔的模具15、挤压模extrusion die使金属挤压成形的模具16、精锻模precision forging die锻制精密锻件的模具。
精密模锻件是指在形状尺寸精度方面高于普通模锻件的锻件17、精压模sizing die对锻件进行少量压缩，以提高锻件局部或整体的尺寸精度的模具18、多向锻模multi-ram forging die能从垂直和水平（或倾斜）方向分别或同时对金属毛坯施加压力，使毛坯能多向成形的模具19、闭塞锻模core forging die具有锻件外轮廓形状的模膛先闭合，然后将冲头压进模膛内部，使金属充满模膛同时冲出锻件孔部所用模具20、胎膜loose tooling在自由锻设备上锻造模锻件时使用的模具21、锻模模块forging die block模锻时承受某一变形工步全部锻击力并带有工作部分的模具主体22、锻模镶块forging die insert对锻模的复杂或易损工作部分单独分开制造，然后镶入模块的零件23、飞边槽flash cave在分模面沿模膛周边设置的、用于保证模膛充满和容纳在成形过程中产生多余材料的凹槽，它由飞边桥和飞边仓组成24、飞边桥flash land飞边槽中和模膛紧相连接的间隙面，多余金属越过该间隙面挤出而形成飞边，它可产生阻力使金属充满模膛25、飞边仓cutter or flash gutter围绕着飞边桥外周的凹槽，用于容纳多余的金属材料26、阻力沟resistance slot在飞边桥部或在模膛难充满处的外边沿垂直于金属流动方向局部设置的小沟槽。
它可以增加水平方向的流动阻力，以利于金属流向难充满的型腔部分27、排气孔vent hole在锻模上为排除锻造时滞留于模膛内的空气而开设的小孔28、导柱guide bushing与导套（或孔）相配合，用以确定模具运动部分的相对位置，保证运动导向精度的圆柱形零件29、导套guide bushing与导柱相配合，用以确定模具运动部分的相对位置，保证运动导向精度的圆筒状零件30、衬套bushing tube为了提高导套等零件的寿命或改善摩擦条件而设置的起衬垫作用的圆筒形零件31、垫板bolster lpate加在凸、凹模支承面与模座间的平板，承受和分散作用在凸模或凹模上的加工负荷32、模座die mounting base(plate)将模具运动或静止部分的零件都安装在运动或静止的模具底座上，该底座称为模座33、模架die sets除直接起成形作用的零件外，由导向装置与上下模座等构成的组合体34、顶杆ejector pin将锻件由模具中顶出的杆形零件35、模膛impression为了使被锻金属获得一定的形状和尺寸，在模块上加工出的成形凹槽36、分模面die parting face上下模或凸凹模的分界面。
分模面可以是平面，也可以是曲面37、预锻模膛blocking impression or rougher为了改善终锻时金属的流动条件，避免产生充填不满和折叠，使锻坯最终成形前获得接近终锻形状的模膛，它可提高终锻模膛的寿命38、终锻模膛finishing impression or finisher模锻时最后成形用的模膛，和热锻件上相应部分的形状、尺寸一致39、定位键locating key定位键是用以确定模具镶块等零件位置的一种定位零件40、键槽key seat在模座或垫板上加工的用以安放定位键的凹槽称为键槽41、制坯模膛blanking impression按锻件变形要求，对坯料体积进行合理分配的模膛，它可以分为滚压模膛，拔长模膛、卡压模膛、弯压模膛、压扁台、镦粗台42、镦粗台upset die为镦粗坯料而在锻模分模面的局部设置的平台，兼有去除坯料氧化皮的作用43、压扁台flattening die face为压扁坯料而在锻模分模面的局部设置的长方形平台，兼有去除坯料氧化皮的作用44、拔长模膛drawing impression使坯料某部分长度增加横截面减小的模膛45、滚压模膛edge rolling impression gathering impression用来减小坯料某部分的横截面积，以增大另一部分横截面积，使坯料体积分配符合锻件轴向分布要求的模膛，坯料在该模膛内成形时要反复翻转90℃46、卡压模膛（亦称压肩模膛）fullering impression使坯料局部高度略为减小，而宽度增加，头部得到少量聚料的模膛，坯料在该模膛内只锤击一次47、弯曲模膛bending impression使坯料弯曲成与锻件水平投影形状相近似的模膛称为弯曲模膛。
其坯料应翻转90℃放到下一模膛中去48、成形模膛forming impression使坯料变形成为锻件水平投影形状相似并作不大的轴向流动的制坯模膛。
在成形模膛锻出的坯料应翻转567放到下一模膛中去49、模锻模膛die forging impression使坯料获得与锻件形状接近或完全一致的模膛，它可分为预锻模膛和终锻模膛50、切断模膛cut-off die一料多件锻造时，用以从棒料上把已锻成的锻件分离的模膛51、劈料台cleaver divider它是预锻模膛的一部分，用以劈开叉部金属，避免内角处充不满52、钳口gate为了便于夹持锻坯，取出锻件，在模膛的出口处设置的凹腔53、浇口sprue钳口与模膛间的沟槽称为浇口，它不仅用作浇注铅样或金属盐样的注入口，还增加了锻件与钳夹头连接的刚度有助于锻件出模54、浇道runner多件同时模锻时，为浇注铅或金属盐在两个终锻模膛间开设的浇料通道55、燕尾dovetail of shank锻模上用楔铁与锤头或砧座相连接的部分56、检验角matched edge or match line在锻模上加工出相互垂直的两个侧面，它是模膛加工的划线基准也是上下模对模的基准57、承击面strking surface上、下锻模接触的表面58、锁扣lock or kick crank为防止锻锤打击时产生上下模错移，而在上下模加工出凸凹相配的凸台和凹挡59、平衡锁扣counter lock模锻在打击力方向具有弯曲轴线的锻件时，为平衡水平分力所置的锁扣60、侧锁扣side lock在模块两侧设置的锁扣61、角锁扣corner lock在模块角部设置的锁扣62、镦粗模upsetting die完成镦粗制坯工步的模块63、卡压模fullering die具有卡压模膛用以完成卡压制坯工步的模块64、成形模forming die完成成形制坯工步的模块65、弯曲模bending die具有弯曲模膛用以完成弯曲制坯工步的模块66、预锻模blocking die具有预锻模膛用以完成预锻工步的模块67、终锻模finishing die有终锻模膛用以完成终锻工步的模块68、导向装置guiding device用以保证上、下模工作时互相对正的装置。
机锻模的导向装置一般由导柱、导套等零件组成69、紧固装置fixing device用以将模块或其它零件固定于上、下模座的装置70、压板clamp plate用于将模块等零件紧固于模座上的一种紧固零件。
有斜面压板和直面压板等形式71、后定位面rear-locating face模架后方的定位基准面称为后定位面72、侧定位面side-locating face模架侧向的定位基准面称为侧定位面73、顶出器ejecter把锻件从模膛中顶出的机构74、顶出杠杆ejection lover把压力机顶杆的动作均匀传递到锻件的顶出器上的杠杆75、多臂顶出杠杆multi-arm ejection lever是能同时推动多个锻件顶出器的顶出杠杆76、顶出环ejection ring起顶出作用的环状零件，用于回转体锻件的顶出77、顶出板ejection plate将压力机顶杆的动作传递给各个顶出器的板状零件78、凸模体（凸模夹持器）body of punchs (holder of punchs)将凸模夹紧固定成一整体，使它和平锻机主滑块一起运动的模体，有整体凸模体和组合式的凸模体79、凸模柄punch shank将凸模接长和固定到凸模体上的连接柄称为凸模柄，其作用可以简化凸模的制造及节约模具钢80、凹模体die body将凹模镶块及所加工的各个模膛联结成可以开闭的组合模块称凹模体，由静止凹模体和活动凹模体组成一付完整的凹模体，前者装于机座专用槽内，后者装于设备的活动部分上81、凸模镶块punch insert组合凸模上局部可换的拼接镶件称凸模镶块，它和凸模本体用不同材料制成，以提高凸模使用寿命，节约贵重材料82、凹模镶块die insert凹模镶块多制成半圆柱体，也有制成立方体的，其上的模膛可全部或局部采用镶块，镶块与凹模体的联接方式采用螺钉紧固83、积聚模膛（聚集模膛）gathering impression使毛坯的局部横截面积增大，以获得锻件粗大部分的模84、穿孔模膛piercing impression将不透孔毛坯冲穿成透孔毛坯的模膛85、切边模膛trimming improssion切除锻件飞边的模膛86、切断模膛cutting impression将锻件或工艺料头从棒料上剪断的模膛87、夹紧模膛gripping impression毛坯局部夹紧，以免凸模加压时毛坯移动，影响成形。