软件验收测试规范(英文第一版)

Software Acceptance Test Specification

ISSUE HISTORY

AMENDMENT HISTORY

TABLE OF CONTENTS

1INTRODUCTION (5)

1.1TEST OBJECTIVES AND COVERAGE (5)

1.2TEST CLASSIFICATION (5)

1.3DOCUMENT OVERVIEW (5)

1.4REFERENCE DOCUMENTS (6)

1.5DEFINITIONS & ABBREVIATIONS (6)

2TEST PREPARATION, SETUP AND SAFETY (7)

2.1TEST SAFETY (7)

2.2TEST ENVIRONMENT (7)

2.3SOFTWARE VERSION INPUT ID (7)

2.4HARDWARE CONFIGURATION (7)

2.4.1TEST EQUIPMENT IDENTIFICATION (7)

2.5TEST PREPARATION AND SETUP (8)

2.6TEST METHOD AND CRITERIA (8)

2.6.1COMPUTER TEST METHOD (8)

2.6.2HDLC TEST METHOD (8)

2.6.2.1NETWORK CARD CONFIGURATION (8)

2.6.2.2INSTALL TMS SIMULATOR SOFTWARE IN THE TEST COMPUTER (10)

2.6.3HMI TEST METHOD (13)

2.6.4TEST EQUIPMENT TEST METHOD (13)

2.7TEST CONTENTS (16)

3CHECKLIST (19)

3.1INITIAL SET UP AND START UP TESTS (19)

3.1.1INITIAL SET UP (19)

3.1.2START UP (19)

3.2INPUTS AND OUTPUTS (19)

3.2.1I/O MAPPING (19)

3.3NETWORK CONTROL (20)

3.3.1HDLC NETWORK TEST (20)

3.3.2NETWORK SIGNALS TEST (20)

3.3.3EMERGENCY VENTILATION MODE (23)

3.4LOCAL CONTROL (24)

3.4.1CAN NETWORK TEST (24)

3.4.2LOCAL CONTROL OPERATION CONDITION TEST (24)

3.4.3READ AND DELETE THE FAULT (26)

3.4.4READ AND DELETE THE RUNTIME (26)

3.4.5SET AND READ THE SYSTEM TIME (26)

3.4.6READ THE TARGET TEMPERATUERE (27)

3.4.7TCMS STATUS DATA (27)

3.4.8INPUT AND OUTPUT STATUS MONITORING (27)

3.4.9COMMUNICATION PORT DATA MONITORING (28)

3.4.10NO OPERATION (28)

3.5DAMPER CONTROL (28)

3.5.1FRESH AIR DAMPER CONTROL (28)

3.5.2RETURN AIR DAMPER CONTROL (29)

3.5.3EMERGENCY BYPASS AIR DAMPER CONTROL (29)

3.6FAULT SIMULATION (30)

3.6.1COMPRESSOR FAULT (30)

3.6.2CONDENSER FAN FAULT (36)

3.6.3EVAPORATOR FAN FAULT (37)

3.6.4TEMPERATURE SENSOR FAULT (37)

3.6.5EMERGENCY VENTILATION INVERTER FAULT (37)

3.7PTU READING (38)

3.7.1RS232 SERIAL PORT COMMUNICATION TEST (38)

3.7.2READ AND DELETE THE FAULT (38)

3.7.3READ AND DELETE THE RUNTIME (39)

3.7.4SET AND READ THE SYSTEM TIME (39)

3.7.5READ THE TARGET TEMPERATURE (39)

3.7.6INPUT AND OUTPUT STATUS MONITORING (40)

3.7.7READ THE FAT/RAT (40)

3.7.8VAC OPERATION CONDITION (40)

3.7.9SET AND READ THE CARRIAGE NO. (41)

4. NOTES AND NON-CONFORMANCES (41)

4.2 TEST NON-CONFORMANCE (42)

1 INTRODUCTION

1.1 TEST OBJECTIVES AND COVERAGE

The purpose of this System Verification Plan (Software Acceptance Test –

SWAT Checklist) is to document the tests to be performed on the ZRJC

SCL1141A project software on the bench. The System Verification bench testing involves simulating the system’s environment to give local control and network control over the software. VAC testing (Factory Acceptance Test – FAT) and field train testing (Site Acceptance Test – SAT) phases are planned following successful completion of bench testing

1.2 TEST CLASSIFICATION

Type Test.

1.3 DOCUMENT OVERVIEW

This document is structured in the following manner.

(a) Section 1– This section described the background, context and environment

for the test.

(b) Section 2 – This section contains the actual test checklist

(c) Section 3 – This section contains comments to be made on the test and

details the non-conformances arising from the test.