三菱电机空调维修

合集下载

三菱电机 菱耀 维修手册

三菱电机 菱耀 维修手册

三菱电机菱耀维修手册常见故障检修方法。

一、压缩机长时间运行,无自动停机现象。

故障原因1:制冷剂用量不足,制冷剂全部或部分泄漏。

故障排除:找出泄漏部位,补漏,重新抽真空制冷系统,加注制冷剂等,由专业人员维护。

原因2:过滤器堵塞。

故障排除:更换过滤器,重新抽真空制冷系统,添加制冷剂等,由专业人员维护。

二、压缩机不能工作。

原因1:电源故障。

故障排除方法:用万用表和电笔检查并排除故障。

如果保险丝断了,请更换保险丝;如果保险丝断了,请更换导线。

原因2:电源电压过低。

故障排除:使用万用表测量电压值,必要时使用电源调节器。

故障原因3:导线连接松动或断路。

故障排除:检查导线的连接部分。

松脱的接头应重新插牢,并由专业人员修理。

三、风扇不能工作。

原因1:主控开关接触不良。

故障排除:用万用表测量主控开关的接触电阻。

如果电阻过大或为零,则修理或更换。

原因2:风扇电机线圈损坏。

故障排除:用万用表检查并更换相同规格和转速的风扇电机。

故障原因3:风扇电机与风扇叶片之间的紧固螺钉松动。

解决方案:拧紧固定螺钉。

原因4:风扇电容器开路或短路。

故障排除:检查电容器,更换相同规格的电容器。

XX电机空调故障代码E1/E2/E3/E4/E5/E6...XX电机空调故障代码如下:E1 :操作开关线断,空内机电路板坏。

E2 :空内位置编号重复/空内板坏。

E3 :无对应的室外机号码内外信号线断。

E4 :室内机号定不正确(设了48 或49 )。

E5 :内外通信异常。

外机板坏。

E6 :室内机热交换器热敏电阻坏,内机板坏。

E7 :室内机吸气敏电阻坏,内机板坏。

E8 :室内机热交换器温度高(暖气),内机热交换器热敏电阻短路。

E10 :操作开关多台控制时次数过多。

XX电机空调故障代码E31~E40故障含义及检修E31:室外机编号重复,外部机板损坏。

E32:对相缺相,外板损坏。

E33:压缩机过流。

缺相,外部机板坏。

E34:52C的初级阶段缺乏T相。

E35:外机温度过高,外机热阻短路,外机短路。

中央空调运行维护详细方案

中央空调运行维护详细方案

中央空调运行维护详细方案目录1. 中央空调系统概述 (3)1.1 系统构成 (3)1.2 运行原理 (5)1.3 维护重要性 (6)2. 中央空调系统的安装与调试 (7)2.1 安装步骤 (8)2.2 调试方法 (9)3. 中央空调系统的日常巡检与保养 (10)3.1 巡检内容 (11)3.1.1 设备外观检查 (12)3.1.2 设备运行状态检查 (14)3.1.3 设备参数检测 (15)3.2 保养措施 (16)3.2.1 定期清洁过滤网 (17)3.2.2 防止冷凝水滴漏 (18)3.2.3 定期更换制冷剂 (19)3.2.4 确保电源稳定 (21)4. 中央空调系统的故障诊断与维修 (22)4.1 常见故障及原因分析 (24)4.1.1 压缩机故障 (25)4.1.2 电机故障 (26)4.1.3 制冷剂不足 (27)4.1.4 其他故障 (28)4.2 维修方法与技巧 (29)5. 中央空调系统的节能与优化方案 (30)5.1 能效评估与分析 (31)5.2 节能措施建议 (33)5.2.1 提高设备效率 (34)5.2.2 采用节能技术 (35)5.2.3 加强维护管理 (36)6. 中央空调系统的案例分析与经验分享 (38)6.1 实际应用案例介绍 (39)6.2 成功经验总结 (41)6.3 建议与改进措施 (42)7. 中央空调行业的发展趋势与前景展望 (43)7.1 行业现状分析 (45)7.2 主要发展趋势 (46)7.3 对未来市场的影响预测 (47)1. 中央空调系统概述中央空调系统是一个集成了供暖、通风与空气调节的设备系统,其目的在于确保各种建筑物内拥有舒适的室内环境。

这一复杂的系统一般包括制冷设备、热交换器、空气处理装置、管道网络、控制系统等多个组成部分。

中央空调系统的运行与维护对于保障其高效运行、延长使用寿命和降低故障率至关重要。

在现代建筑中,中央空调系统不仅关乎居住或工作的舒适度,还涉及到能源效率与成本控制的问题。

三菱重工空调故障代码

三菱重工空调故障代码

三菱重工空调故障代码三菱重工空调故障代码LED1 LED2 LED3 LED4 故障原因灭灭灭灭正常亮亮亮亮室外机主版故障亮灭灭灭相序错误灭亮灭灭高压继电器动作或室外主控板故障灭灭亮灭低压继电器动作或室外主控板故障灭灭灭亮外环温异常或温度过高三菱电机空调GJ外机接线端子功能表短路端子号短路端子功能不短接时短接时J1 相位反向检测不检测检测J2 卸压阀控制除霜时关除霜时开J3 曲轴箱E加热连续加热相隔1小时重复开关J4 上电3分钟延时有无三菱电机空调GJ外机故障代码发光二极管闪烁故障原因发光二极管亮LED1 相序错误室内输出控制信号正常LED2 缺相室内输出控制信号正常LED3 外环温异常63H1运行LED4 63H2动作压缩机启动LED5 室外51C动作保护室外风机启动LED6 室外26C动作保护四通阀启动LED7 过热保护卸压阀启动LED8 控制输入电路异常曲轴箱加热器启动三菱重工空调故障代码【二】三菱电机空调GJ(PSH-3GJ、6GJ[H]S)灯亮位置故障原因12--29 室外故障(检查室外机连接线、制冷剂、温度传感器)11--28 室外环温异常或控制板故障10--27 内管温异常或控制板故障7--24 防冷风保护(室内进出风口有无障碍,室内电机)注:室内故障灯在面板左恻显示,室内JP4短路件插上时,首次上电无延时功能,否则相反。

室内JP2短路插件插上,可将防冷风温度由1度改为负2度。

三菱重工:显示内容故障原因检查灯(黄)闪亮室内管温或环温异常运行灯(黄)闪亮二次电源过欠压保护检查灯(黄)闪亮一次过冷保护检查灯(黄)闪亮二次过热保护检查灯(黄)闪亮三次室外机保护装置动作检查灯(黄)闪亮四次浮子开关动作,水泵排水不正常检查灯(黄)闪亮五次室内管温传感器检查25度以上三菱重工504系列显示代码故障原因E1 室外机电源关闭或电源线断开(保险、变压器坏)E2 室内机机号重复或室内主板损坏E3 室外机机号设定不良,室外机信号线断开或电源关E4 室外机机号设定不良或室内机主板损坏E5 室外机电源关、室外侧信号线断或控制板损坏E6 室内侧温度传感器开路或室内主控制板损坏E7 室内机吸入温度传感器或室内主控制板损坏E8 过热保护(室内管温或室内主板损坏)E9 运转开关误动作(选择开关或室内主控制板损坏)E10 多台中心控制时室内连接台数超过17台E31 室外机侧机号重复或室外主控制板故障E32 电源相序错、缺T相、外管温异常、外主板坏E33 压缩机过载缺S或R相、52C二次侧断开保护E34 压缩机缺T相(52C二次侧)室外主控制板损坏E35 制冷时室外散热器超过设定或室外管温故障,外主板坏E36 室外排气管温过高保护(35-80型120度、90-200型135度以上)E37 室外管温开路,室外主控制板故障E38 室外温度传感器开路,室外主控制板故障E39 室外排气管温度传感器开路,室外主控板故障E40 室外机保护元件动作,室外主控板故障注:室内红灯LED闪表示室内故障,绿灯LED亮表示室内正常。

三菱电机空调维修

三菱电机空调维修

三菱电机空调维修空调使用时间久了难免会出现故障,你知道空调的维修方法吗?下面咱们一起来看看使用三菱电机空调时的注意事项,和一些常见的故障维修方法:1.现象:空调系统不工作且空调的压缩机不吸合。

成因:制冷剂部分或全部泄露。

维修:找出导致制冷剂泄漏的故障点,并更换损坏的零件,然后重新将其抽成真空状态,再添加适量的制冷剂。

容易发生制冷剂泄漏的部位有:管路及其密封圈、冷凝管、膨胀阀、压力开关等。

2.现象:空调不能制冷,压缩机能够吸合,但低压很低且排出管表面温度极高。

成因:膨胀阀上的感温头损坏,导致冷媒泄漏无法制冷。

维修:将坏掉的感温头换掉,并将系统抽成真空、保压,然后根据空调规定的剂量适量添加制冷剂。

注意事项:1、空调使用季节,内机过滤网每个月用自来水清洗一次,内机冷凝器每个季度用专用的泡沫清洁剂清洁一次,外机散热器每个季度用自来水冲洗一次。

2、较长时间不使用时,要拔下插头,一是不浪费待机耗电,二是用电安全。

3、温度设定不要与环境温度相差过大,以免压缩机连续运转不停机,磨损大耗电大。

4、空调不使用季节,除了电源插头拔下外,遥控器的电池要取下,以防漏液锈蚀。

5、遇到内机的指示灯全部跳闪,是自检报警和压缩机保护报警,立即拔下插头,报修。

6、机器正常使用,不发生系统管路泄漏的,制冷剂不会随使用时间损耗。

7、空调器室外散热器上积灰太多会使效率下降,应定期检查和清扫室外散热器(在停电后进行,可用压缩空气吹净);8、分体式空调器室外机组不可用棍棒类物体插入,否则风扇将被卡住或损坏;9、当感到空调器使用不理想时应查阅使用说明书,分析是否因使用不当而引起,查明原因后进行纠正;10、发现故障后不能自行处理时,可找原安装部门的专业维修技工解决,或与该品牌公司当地服务人员联系,不可自行修理或找非专业人员检修;11、空调器不使用时应及时拔掉电源;12、空调器停机后必须待三分钟后再次启动,以保护压缩机;13、带有遥控器(不应放在小孩易取之处)的空调器在使用中不要被小孩当成玩具操作,以免损坏机器。

三菱电机房间空调器说明书

三菱电机房间空调器说明书

各部件名称...........................操作前的准备工作.....................“I FEEL...”(体感...)自动运转 ....选择运转模式时(製冷、除湿、製热、送风)..动态地面测温控製操作.................动态地面测温传感器的测温方向设定.....风速·风向的调节.....................睡眠模式运转.........................凉感控製运转.........................定时器运转(定时开·定时关).........空调机长期不使用时...................维护.................................前面板的清扫.........................过滤网的清扫.........................在请维修人员之前,请再次检查以下项目.当您认为「发生故障」时...............移机·检查...........................安装安全事项.........................安装说明.............................135678910121313141414151616171720Safety precautions .....................................Part name ..................................................Preparation before operation ....................."I FEEL..." Auto Operation .........................Manual operation (Cooling, Dry, Heating,Fan) ..........................................................."MOVE EYE"CONTROL OPERATION ......AREA SETTING ........................................Air flow velocity and direction adjustmentSleep operationEcono Cool operation .......Econo Cool operation ................................Timer operation (OFF TIMER-ON TIMER) ...When the air conditioner is not used fora long time .................................................Maintenance ..............................................Front panel cleaning ..................................Filter Cleaning ...........................................Please check the following itemsbefore connecting a serviceman...............When you think trouble occurs ..................Removal and inspection ............................Safety precautions for Installation .............Installation instructions ..............................2729303233343537383939404040414242434346安装结束后,请安装人员务必在安装结算联和保修卡上按要求贴好条形码。

三菱空调故障代码全攻略

三菱空调故障代码全攻略

三菱空调故障代码全攻略三菱电机:LED1 LED2 LED3 LED4 故障原因灭灭灭灭正常亮亮亮亮室外机主版故障亮灭灭灭相序错误灭亮灭灭高压继电器动作或室外主控板故障灭灭亮灭低压继电器动作或室外主控板故障灭灭灭亮外环温异常或温度过高三菱电机空调GJ外机接线端子功能表短路端子号短路端子功能不短接时短接时J1 相位反向检测不检测检测J2 卸压阀控制除霜时关除霜时开J3 曲轴箱E加热连续加热相隔1小时重复开关J4 上电3分钟延时有无三菱电机空调GJ外机故障代码发光二极管闪烁故障原因发光二极管亮LED1 相序错误室内输出控制信号正常LED2 缺相室内输出控制信号正常LED3 外环温异常63H1运行LED4 63H2动作压缩机启动LED5 室外51C动作保护室外风机启动LED6 室外26C动作保护四通阀启动LED7 过热保护卸压阀启动LED8 控制输入电路异常曲轴箱加热器启动三菱电机空调GJ(PSH-3GJ、6GJ[H]S)灯亮位置故障原因12--29 室外故障(检查室外机连接线、制冷剂、温度传感器)11--28 室外环温异常或控制板故障10--27 内管温异常或控制板故障7--24 防冷风保护(室内进出风口有无障碍,室内电机)注:室内故障灯在面板左恻显示,室内JP4短路件插上时,首次上电无延时功能,否则相反。

室内JP2短路插件插上,可将防冷风温度由1度改为负2度。

三菱重工:显示内容故障原因检查灯(黄)闪亮室内管温或环温异常运行灯(黄)闪亮二次电源过欠压保护检查灯(黄)闪亮一次过冷保护检查灯(黄)闪亮二次过热保护检查灯(黄)闪亮三次室外机保护装置动作检查灯(黄)闪亮四次浮子开关动作,水泵排水不正常检查灯(黄)闪亮五次室内管温传感器检查25度以上三菱重工504系列显示代码故障原因E1 室外机电源关闭或电源线断开(保险、变压器坏)E2 室内机机号重复或室内主板损坏E3 室外机机号设定不良,室外机信号线断开或电源关E4 室外机机号设定不良或室内机主板损坏E5 室外机电源关、室外侧信号线断或控制板损坏E6 室内侧温度传感器开路或室内主控制板损坏E7 室内机吸入温度传感器或室内主控制板损坏E8 过热保护(室内管温或室内主板损坏)E9 运转开关误动作(选择开关或室内主控制板损坏)E10 多台中心控制时室内连接台数超过17台E31 室外机侧机号重复或室外主控制板故障E32 电源相序错、缺T相、外管温异常、外主板坏E33 压缩机过载缺S或R相、52C二次侧断开保护E34 压缩机缺T相(52C二次侧)室外主控制板损坏E35 制冷时室外散热器超过设定或室外管温故障,外主板坏E36 室外排气管温过高保护(35-80型120度、90-200型135度以上)E37 室外管温开路,室外主控制板故障E38 室外温度传感器开路,室外主控制板故障E39 室外排气管温度传感器开路,室外主控板故障E40 室外机保护元件动作,室外主控板故障注:室内红灯LED闪表示室内故障,绿灯LED亮表示室内正常。

三菱电机MSZ-FX20VFK MSZ-FX25VFK空调器使用说明书

三菱电机MSZ-FX20VFK MSZ-FX25VFK空调器使用说明书

安装结束后,请安装人员务必在安装保修指南的制造商信息登记联和保修卡上按要求贴好条形码本空调机充注R32环保制冷剂,请在安装、使用、维修前阅读使用安装说明书,否则可能会引发火灾造成人身伤害和财产损失。

使用前,请务必详读此「安全事项」。

这里所示的注意事项,是一些有关安全的非常重要的内容,一定要遵守。

绝对禁止。

请务必按指示操作。

禁止插入手指头或棒条等。

请务必关闭电源。

文中所用“图形符号”含义如下警告禁止在电源线的中途引线或延长电源线禁止用杀虫剂·消毒剂·可燃性本空调机的安装、移机、维修必须由厂家指定的且有专业资质的人员进行操作因为若操作不当将可能引起火空调不制冷·不制热时有制冷剂泄漏的可能。

如发现制冷剂泄漏,请立即停机且打开所有门窗换气,并立即与本空调机的出售店或售后服务中心联系!和燃烧器具一起使用时,应该时常换气可能产生氧气不足的现象。

注意室内外机组下面不得堆放必须安装漏电断路器警告注意注意若不装漏电断路器,便可能有触电的危险。

禁止给电池充电或拆卸电池,禁止投入火中如果电池液沾到皮肤或衣服,请安装机器禁止在直接吹到空调机气流的地方放置动植物禁止敞开门窗,在高湿度状况下作长时间的运转禁止踩在室内/室外机组上或在上面堆放东西可能跌下受伤或机器掉落伤人。

长期不使用机器时,应关闭电源开关因堆积灰尘而有可能引起火灾和事故。

室内机组室外机组(背面·侧面)进 风 口 进风口前面板内侧导风板(左右风向)正面导风板前导风板后导风板温度传感器湿度传感器「清扫复位」键左右风向导风板上下风向导风板无线适配器〈大文字画面显示例〉请点击液晶画面,画面灯亮后开始遥控器操作。

约过30秒不进行操作的话,液晶画面会再暗掉。

液晶画面灯灭后一分钟内再点击的话会显示灯灭前的画面。

关于液晶画面(触屏画面)在菜单或设定画面中呈阴影状的是无法设定的项目,点击这些项目会显示简单的说明。

在触屏上点击显示的图标或项目即可进行操作。

三菱中央空调维修故障代码分析,三菱空调故障代码大全

三菱中央空调维修故障代码分析,三菱空调故障代码大全

三菱中央空调维修故障代码分析,三菱空调故障代码大全格力空调故障代码E1:压缩机高压保护。

1﹑冷凝器前有障碍物2﹑室外环境温度高于43度时开始制冷3﹑控制回路异常4﹑高压管压力过大使高压开关动作E2:蒸发器防冻结保护。

1﹑室内风机不转或风口堵住。

2﹑室内环境温度低于18度。

3﹑管温感温头折断。

4﹑管温感温头插头没插好。

5﹑控制回路异常。

E3:压缩机低压保护。

1﹑冷媒不足。

2﹑膨胀阀半堵,电磁阀故障。

3﹑过滤器半堵。

E4:压缩机排气温度过高保护。

1﹑系统堵塞。

2﹑压缩机老化。

3﹑外机散热不好。

E5:过电流。

格力KF-60L WAK分体立柜式房间空调器故障代码﹕E11﹑冷凝器前有障碍物2﹑控制回路巽常3﹑室外环境温度高于43度时开始制冷4﹑高压管压力过大使高压开关动作E2 1﹑室内风机不转或风口堵住2﹑室内环境温度低于18度3﹑管温感温头折断4﹑管温感温头插头没插好5﹑控制回路巽常6﹑电容C7漏电格力LF-12WAK分体立柜式房间空调器故障代码﹕E11﹑冷凝器前有障碍物2﹑控制回路巽常3﹑三相电源缺相3﹑室外环境温度高于43度时开始制冷4﹑工作电流过大使过护器动作或高压管压力过大使高压开关动作E21﹑室内风机不转或风口堵住2﹑室内环境温度低于18度3﹑管温感温头折断4﹑管温感温头插头没插好5﹑控制回路巽常6﹑电容C7漏电E1一般是外机问题过欠流过欠压散热不良!格力KFR-70LW/ED 故障代码KFR-70LW/ED E1 高压E2 防冻结E3 低压E4 排温E5 过流格力带低电压保护新款柜机代码:E1:压缩机高压保护E2:蒸发器防冻结保护E3:压缩机低压保护E4:压缩机排气温度过高保护E5:过电流是哪里故障2、6指示灯闪烁水位天关3、6指示灯闪烁扫风电机损坏2、3、6指示灯闪烁选择问题2、5指示灯闪烁室内温度传感器损坏2、4、5指示灯闪烁遥控器问题3、5指示灯闪烁室内温度传感器损坏4指示灯闪烁中心地址堵塞2指示灯闪烁遥控器发射电路开路3、7指示灯闪烁室内外通信开路2、7指示灯闪烁室风外通信问题3、4、6、7指示灯闪烁电源接触不良,检测主电路板2、3、4、6、7指示灯闪烁电源接触不良,检测电路板4、6、7 指示灯闪烁压缩机吸气压力过低保护3、6、7指示灯闪烁压缩机排气压力过高保护2、6、7指示灯闪烁压缩机过流保护2、3、6、7指示灯闪烁压缩机排气温度保护2、5、7指示灯闪烁压缩机排气温度问题3、5、7指示灯闪烁热交换器温度问题2、4、5、7指示灯闪烁高压开关开路3、4、5、7指示灯闪烁热压开关开路2、3、4、5、7指示灯闪烁低压开关问题2、3、5、7指示灯闪烁电流检测器开路或压缩机过流保护格力空调故障代码h1是化霜故障。

三菱重工海尔空调故障代码

三菱重工海尔空调故障代码

三菱重工海尔空调故障代码变频空调故障代码1、KFR—26GW/BPF、KFR-26GW/A(BPF)、KFR-26GW/C(BPF)、KFR-28GW/BPA、KFR-28GW/BPF、KFR—28GW/A(BPF)、KFR-28GW/C(BPF)、KFR—40GW/BPF、KFR-40GW/A(BPF)、KFR-28GW/DBPF、KFR-36GW/DBPF、KFR—28GW/M(BPF)、KFR-36GW/M(BPF)、KFR—25GW*2/BP、KFR—25GW*2/BPF、KFR—25GW*2/BPJF、KFR—26GW*2/BPF、KFR—30GW*2/BPF、KFR—30GW*2/BPKF、KR—(32G/AF。

40G/F)60W/BP、KR—(32G/AF。

50L/F)70W/BP室内机显示灯故障原因维修方法备注电源定时运转闪灭灭室内环温传感器闪亮亮室内热交传感器1.检查过滤网是否脏、热交换器换热是否正常,风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修亮亮闪室外除霜传感器(检修只适用于一拖一机型)闪亮灭压机排气温度传感器1、检查过滤网是否脏、热交换器换热是否正常、管路安装是否完好2、检查传感器阻值3、若以上正常,拉回检修亮闪灭室外环境温度传感器上门检修闪灭亮室外传感器异常(检修只适用于一拖二机型)闪灭亮压机运转异常1、检测电压是否正常、管路是否安装完好;2、若以上正常,拉回检修(只适用于一拖一机型)闪闪亮1。

DC电流检知2、过电流保护动作3、功率模块温度过高保护4、功率模块低电压检知(1、检测电压是否正常,2、电压正常,拉回检修)室内机显示灯故障原因维修方法电源定时运转闪闪灭过电流保护动作AC电流检知1、上门检测电压是否正常;2、电压正常,拉回检修闪闪闪制热时,蒸发器温度上升(68度以上),或室内风机风量小1、检查过滤网是否脏、热交换器换热是否正常、风速是否正常;2、若以上正常,拉回检修闪灭闪CT断线保护上门检修亮闪亮功率模块异常上门检修灭灭闪通讯异常上门检修灭闪灭排气管温度超过120度(1、检查过滤网是否脏、热交换器换热是否正常、管路安装是否完好2、检查传感器阻值3、若以上正常,拉回检修)灭闪亮电压不足解释原因,让用户断电10-15分钟后重新上电开机灭亮闪控制基板异常上门检修灭亮闪室内机EEPROM异常上门检修闪亮闪室外机EEPROM异常上门检修2、KFR—35GW/BPF、KFR—35GW/ABPF、KFR—36GW/BP、KFR—36GW/BPF 、KFR-36GW/ABPF、KFR—50GW/BPF、KFR—50LW/BP、KFR-50LW/BPF故障现象故障原因维修方法备注定时灯闪烁1次功率模块过热、过流、短路拉回检修室外机定时灯闪烁2次电流传感器感应电流太小上门检修定时灯闪烁4次制热时压机温度传感器温度超过120度保护1、上门检查热交换器换热是否正常、管路安装是否正确否2、检查压机传感器阻值3、若以上正常,拉回检修定时灯闪烁5次过电流保护1、上门检测电压是否正常;2、电压正常,拉回检修定时灯闪烁6次室外环温传感器故障上门检修定时灯闪烁7次室外热交传感器故障上门检修定时灯闪烁10次电源超、欠压解释原因,让用户断电10-15分钟后重新上电开机定时灯闪烁11次瞬时断电保护解释原因,让用户断电10-15分钟后重新上电开机定时灯闪烁12次制冷时室外热交传感器温度超过70度保护 1、上门检查热交换器换热是否正常;2、检测传感器阻值3、若以上正常,拉回检修定时灯闪烁14次单片机读入EEPROM数据有错误上门检修定时灯闪烁15次瞬时断电时单片机复位解释原因,让用户断电10-15分钟后重新上电开机故障现象故障原因维修方法备注电源灯闪烁1次室内环温传感器故障修室内机电源灯闪烁2次内热交传感器故障1、检查传感器阻值;2 、查过滤网是否脏、热交换器换热、风速是否正常;3、若以上正常,拉回检修电源灯闪烁4次制热时室内热交传感器温度超过72度保护1、上门检查过滤网是否脏、热交换器换热、风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修电源灯闪烁5次制冷时室内热交传感器温度低于0度保护1、检查过滤网是否脏、热交换器换热,风速是否正常;2、测传感器阻值3、若以上正常,拉回检修电源灯闪烁6次瞬时断电时单片机复位解释原因,让用户断电10—15分钟后重新上电开机电源灯闪烁7次通讯回路故障上门检修电源灯闪烁8次室内风机故障上门检修电源灯闪烁9次瞬时断电保护解释原因,让用户断电10—15分钟后重新上电开机3、KFR—36GW/B(BPF)、KFR-36GW/BPJF、KFR-28GW/BPJF、KFR—28GW/(BPF)、KFR—36GW/(BPF)室内机显示故障原因维修方法E1室内环境温度传感器上门检修E2室内热交温度传感器1、上门检查过滤网是否脏、热交换器换热是否正常,风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修F21室外除霜温度传感器上门检修F25室外排气温度传感器1、上门检查过滤网是否脏、热交换器换热是否正常、管路安装是否完好2、检查传感器阻值3、若以上正常,拉回检修F6室外环境温度传感器上门检修E07通讯异常上门检修室内机显示故障原因维修方法F24CT断线上门检修F4排气温度超过120℃,排气管温度过升保护1、上门检查过滤网是否脏、热交换器换热是否正常、管路安装是否完好2、检查传感器阻值3、若以上正常,拉回检修F22AC电流过电流保护1、上门检测电压是否正常;2、电压正常,拉回检修F23DC电流过电流保护1、上门检测电压是否正常;2、电压正常,拉回检修E9制热时,蒸发器温度上升(68℃以上),或室内电机运转但风量小1、上门检查过滤网是否脏、热交换器换热是否正常,风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修F11压机运转异常拉回检修E8面板主板通讯异常上门检修4.KFR-60LW/BPF故障显示故障原因维修方法E1室温传感器故障上门检修E2室内盘管传感器故障1、上门检查过滤网是否脏、热交换器换热是否正常,风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修E3室外环温传感器故障上门检修E4室外盘管传感器故障上门检修E5过电流保护1、上门检测电压是否正常;2、电压正常,拉回检修E6压机过热保护1、上门检查过滤网是否脏、热交换器换热是否正常、管路安装是否完好2、检查压机传感器阻值3、若以上正常,拉回检修E7室外低电压保护解释原因,让用户断电10-15分钟后重新上电开机E8面板与主板通讯故障上门检修E9室内外通讯故障上门检修5FR-48LW/@(BPJXF)、KFR-48LW/@(BPF)、KFR—50LW/BPJXF、KFR-51LW/BPJXF、KFR-51LW/BPJF、KFR-51LW/N(BPF)、KFR—51LW/T(BPJXF)、KFR-51LW/@(BPJXF)、KFR—52LW/BPJXF、KFR-52LW/BPJF、KFR-52LW/E(BPJXF)、KFR—52LW/N(BPJXF)、KFR-58LW/BPJXF、KFR-58LW/E(BPJXF)、KFR-58LW/N (BPJXF)、KFR—58LW/N(BPF)、KFR—58LW/T(BPJXF)、KFR-58LW/@(BPF)、KFR-58LW/@(BPJXF)、KFR—60LW/BPJXF、KFR—60LW/BPJF、KFR—60LW/BPXF、KFR—60LW/E(BPJXF)、KFR—68LW/BPJXF、KFR-68LW/E (BPJXF)、KFR—68LW/@(BPJXF)等故障代码故障原因维修方法E1功率模块过热、过流、短路拉回检修E2电流传感器感应电流太小上门检修E4制热时压机温度传感器温度超过120℃1、上门检查过滤网是否脏、热交换器换热是否正常、管路安装是否完好;2、检查压机传感器阻值;3、若以上正常,拉回检修E5过电流保护1、上门检测电压是否正常;2、电压正常,拉回检修E6室外温度传感器故障上门检修E7室外盘管传感器故障上门检修Ea电源超欠压解释原因,让用户断电10—15分钟后重新上电开机Ec制冷时室外热交传感器温度超过70℃保护1、上门检查过滤网是否脏、热交换器换热是否正常;2、检测传感器阻值;3、若以上正常,拉回检修Ee单片机读入EEPROM数据有错误上门检修F1室温传感器故障上门检修F2室内盘管传感器故障1、上门检查过滤网是否脏、热交换器换热是否正常,风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修F4制热时室内盘管传感器超过72℃保护1、上门检查过滤网是否脏、热交换器换热是否正常,风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修F5制冷时室内盘管温度传感器低于0℃以下保护1、上门检查过滤网是否脏、热交换器换热是否正常,风速是否正常;2、检测传感器阻值3、若以上正常,拉回检修F7室内主板与控制面板通讯故障上门检修E1 室内温度传感器E2室外盘管传感器E3室外温度传感器E4室外盘管传感器E5电流过大E6压力保护E7低电压保护E8面板,主板(内)通信故障E9室内,外板通信故障三菱重工海尔柜机故障代码E1 操作开关线断、室内机电路板不良。

三菱空调RC-EXC3中文使用手册说明书

三菱空调RC-EXC3中文使用手册说明书

[F1] [F2] 开关屏幕更改为 ③⇒④⇒⑤ 屏幕更改为 ①⇒⑧⇒⑤主子线控器版本:程序 ID :请设定为主机或子机。

主子如果在 10 分钟内未建立通信,红色 LED 将闪烁。

⑤TOP 画面菜单风向冷房16:14(周一)F1:高能力运转F2:节能运转定时器设定停止中。

设定温度③室内机检索打开室内机检索中④室内机信息采集打开室内机信息获取中。

距离完成约需 1230 秒钟。

已设定主/子时屏幕更改为 ⑧⇒⑤。

屏幕更改为 ⑦。

如果超过 15 秒没有按屏幕,选择 (继续),显示屏更改为 的屏幕。

⑧初始化设定打开线控器初始设定中。

⑥设定继续确认是否保持上电前的设定?是否屏幕更改为 ①⇒②。

屏幕更改为 ⑥。

初始化之后,返回默认状态。

屏幕更改为 ①⇒②。

屏幕更改为 ⑥。

初始化之后,返回默认状态。

⑦初始化确认是否初始化全部线控器设定?是否通过 ▲ ▼ 按钮选择日期并按 设定 按钮。

显示所选屏幕。

显示所选屏幕。

可以在冷房停止时运转。

当室温低到开始冷房试运转时,通过将设定温度降低至 5°C,运转 30 分钟。

排水泵可以单独运转。

⑧冷房试运转冷房试运转返回开始点击开始后,以冷房模式设定 5°C ,试运转 30 分钟。

经过 30 分钟及变更 TOP 画面上的运转/停止、运转模式、设定温度的设定,则试运转结束。

排水泵试运转返回运转停止请选择设定。

安装日登录年月日返回设定请设定年月日。

安装设定安装日登录售后信息输入试运转风管机静压修正自动地址变更下一页返回请选择设定。

安装设定主室内机地址设定室内机后备运转功能红外线传感器设定面板升降操作上一页返回请选择设定。

使用最多 13 个字符登记联络人的电话号码,然后按 设定 按钮。

⑥登记联络人电话联络人电话返回设定删除请输入联络人电话并按“设定”。

输入售后信息。

售后信息输入联络人联络人电话返回请选择设定。

使用最多 26 个单字节字符登记联络人的姓名,然后按 设定 按钮。

新版三菱电机中央空调故障代码-三菱电机空调故障代码解释排除-三菱电机中央空调故障代码大全

新版三菱电机中央空调故障代码-三菱电机空调故障代码解释排除-三菱电机中央空调故障代码大全

新三菱电机中央空调故障代码,三菱电机空调故障代码解释排除,三菱电机中央空调故障代码大全聚信口碑网整理汇总新三菱电机中央空调故障代码,三菱电机空调故障代码解释排除,三菱电机中央空调故障代码大全供大家对比参考。

大家查故障的时候要对照好自己的机型,家用商用的故障代码含义也不一样。

对假故障的处理都是一样的,可以断电5分钟重启排除。

三菱电机空调常见故障先列出来。

E1 :操纵开关线断,空内机电路板坏。

E2 :空内地位编号反复/空内板坏E3 :无对应的室外机号码表里信号线断E4 :室内机号定不准确(设了48 或49 )E5 :表里通信非常。

外机板坏。

E6 :室内机热交流器热敏电阻坏,内机板坏。

E7 :室内机吸气敏电阻坏,内机板坏。

E8 :室内机热交流器温度高(暖气),内机热交流器热敏电阻短路E10 :操纵开关多台控制时次数过多E31 :室外机号码反复,外机板坏E32 :反相成缺相,外机板坏E33 :主机机过流。

缺相,外机板坏。

E34 :52C的低级缺T相,E35 :外机温度过高,外机热敏电阻短路,外机短路。

E36 主机机出口冷管温度过高E38 :室外机气温热敏电阻不良‘E39 :主机机出口冷管温度热敏电阻不良E40 :主机机高压过高。

uA 。

室外与室内装置不配或序号差别。

uf .电路接纳头有故障聚信口碑网整理汇总三菱电机中央空调故障代码大全自我诊断功用实用与SRF50HC SRFD50HC SRF60HC SRFD60HC型号三菱重工空调非常表现内容运转灯诊断暗号(室内机表现部分的室温表现处)室内机吸气热敏电阻非常闪亮(2次/8秒)07室内机热交流器电阻非常闪亮(2次/8秒)06室外机非常闪亮(2次/8秒)59有线遥控器通信非常闪亮(2次/8秒)00控制单块通信非常闪亮(2次/8秒)00*开机三无,(既不制冷.不启动,电源指示灯不亮)。

*电源指示灯亮(不制冷,遥控不起作用三菱空调维修。

)。

*按键不灵(按键没反响,一般按键不起作用。

三菱MSZ系列变频空调机常见故障维修

三菱MSZ系列变频空调机常见故障维修

(1).断开电源和室内外连线3#线。 (2).用短接线将3-N端短接。 (3).接通电源,按下遥控器开关。 (4).(SV,TV机型)查看室内机“21”指示灯是否闪烁?
(VV机型)查看室内机“定时”指示灯是否闪烁? 如没有则判室内电路板故障,如有则判室内电路板完 好。 (5).如室内电路板完好,则检验室内外机连接线旳绝缘和 接线是否完好和正确?如完好正确,则鉴定室外电路 故障。 (6).检验室外R64电阻和噪声滤波电路板是否完好? 如完好,则鉴定室外变频主电路板故障。
判断措施1: (1).断开电源和室内外连线3#线. (2).用万用表5MA直流电流档将3-N端短接. (3).接通电源,按下应急操作开关. (4).52C继电器接通后,在4S~5S内大约是否有1~3MA电
流波动?,如没有则判室内电路板故障,如有则判室内 电路板完好. (5).如室内电路板完好,则检验室内外机连接线旳绝缘和 接线是否完好和正确?如完好正确,则鉴定室外电路 故障. (6).检验室外R64电阻和噪声滤波电路板是否完好? 如完好,则鉴定室外变频主电路板故障.
故障3: 室外机组停止运营,三分钟之后又重新开启.而且反复进 行.室内机无故障显示.室外LED灯闪3次,闪4次,闪5次(间 隔2.5S). 原因: 过热保护 故障: (1).排放温度过热保护
(2).功率模块过热保护 (3).主电路板过热保护 (4).室内盘管过热保护
判断:
1. LED灯闪3次(间隔2.5S)(排放温度>116℃): (1).制冷系统故障:
判断措施2:(用遥控器检验)
先设置遥控器为故障检验模式 a. SV、TV型:同步按下遥控器上旳运转模式按钮和复位
按钮,然后脱开复位按钮,等遥控器液晶显示部显示全 部内容后脱开运转模式按钮。 b. VV型:同步按下遥控器上旳运转模式按钮和过冷模式 按钮、按下复位按钮, 3秒后脱开复位按钮,等遥控器液 晶显示 部显示全部内容后脱开运转模式按钮。

三菱电机与东芝家用中央空调比较

三菱电机与东芝家用中央空调比较

1、2014年3月31日,广东省工商局重磅出击,公布2014年首批认定有缺陷的商品名单。

在曝光的不合格空调产品中,只有三菱电机一个品牌,并且同时4款产品均上黑榜。

四款产品均被检出电源连接和外部软线,和接地措施不合格。

空调产品的软线固定装置不能满足标准要求,则会令线体在受力时,其接线端子处受力可能会导致导线脱落,造成电线短路或令产品壳体带电的安全危险。

同时,由于提供接地连续性的螺钉通过易于变形的材料传递接触压力,螺钉没有足够的回弹力补偿温度发生变化时材料可能出现的收缩或变形,存在着接地不可靠的安全隐患。

2、三菱电机和重工所有系列都无法使用智能控制。

3、打击三菱电机:a、三菱电机噪音偏大(实际使用比大金、日立、噪音都大),经销商多次向厂家反映,三菱电机中央空调生产量相对壁挂机要少的多,市场占有率低,并没有引起厂家重视,一直未作改进。

b、三菱菱耀系列分歧箱连接,是菱尚和菱睿系列之间的过渡产品,分歧箱连接导致管道的浪费,内机效果的衰减,打孔孔径大,打孔数量多。

菱睿系列是三菱电机技术最成熟、最新型、价格最贵的产品系列。

c、三菱电机菱耀、菱睿系列采用涡旋式压缩机。

d、三菱电机菱尚系列5B120(4P)外机实际使用效果性能很不稳定,2012年各经销商已经暂停销售。

(菱耀、菱尚系列产品不带合格证。

)三菱电机菱睿系列(Smart Multi)多联分体式空调1、运行温度范围:-20℃——46℃。

东芝-25℃-52℃,ME社的所有产品在温度低于-10℃时,需要安装底座加热器。

2、使用R410A冷媒,但是R410A冷媒是针对双转子压缩机,与涡旋式压缩机不匹配,易烧毁。

3、三菱电机空调压缩机采用的是直流无刷电机4、菱睿系列侧出风机器4P/5P/6P/8P/10P均为双风扇,12P-18P都是顶出风外机(且有一面是铁板,无法换热的)1、菱睿:双风扇:PUMY-P***V HMC-S(国产,侧出风,220V,除以25即为匹数)2、菱睿:双风扇:PUMY-P***Y HMC-C(日本产,侧出风,380V,除以25即为匹数)3、菱睿:双风扇:PUMY-P***YK MC-C(日本产,侧出风,380V,除以25即为匹数)菱睿系列内机种类很少,只有6种,小巧(带泵,不带泵)、天花暗藏(超薄型,机器深度700,东芝超薄进口,深度645)、天花型卡式(单向送风)、天花型暗藏(中静压)、壁挂式、天花型卡式(四向送风)。

2020新版北京市空调工商企业公司商家名录名单黄页联系电话号码地址大全1496家

2020新版北京市空调工商企业公司商家名录名单黄页联系电话号码地址大全1496家

北京市 北京市 丰台区 北京市 北京市 西城区
北京市 北京市 朝阳区
北京市 北京市 昌平区 北京市 北京市 朝阳区
北京市 北京市 怀柔区
北京市 北京市 房山区
北京市 北京市 昌平区
北京市 北京市 北京市 北京市 北京市 北京市
北京市 北京市 北京市 北京市 北京市 北京市
通州区 昌平区 朝阳区 延庆区 丰台区 海淀区
黄村镇兴政街28号2层 横一条2号楼底商6号 坨头路与阎河路交叉口西北200米 东交民巷10号院一层A2 南宫路西100米 安定路20号苏宁电器2层 古城大街31-4号 朝阳路刨花板市场中心一层 东三环中路55号楼
北京市 北京市 西城区
美的集团北京市美的商用 宣武门外大街10号庄胜广场中央办
空调销售有限公司
公楼北翼1111-1112室
北京市 北京市 海淀区
西三旗空调移机维修服务 点
西三旗建材城西路27号
北京市 北京市 朝阳区 美的空调(朝阳区店)
三台山路3-1号
北京市 北京市 朝阳区
中国建筑科学研究院建筑 物理研究所空气调节研究 北三环东路30号附近 所
北京市 北京市 北京市 北京市
北京市 北京市
北京市 北京市
北京市五环空调净化工程
有限公司 北京空调拆装移机(海淀
店) 格力空调
广源东街8正东方向90米
建材城西一里4号楼2层2001 大石窝村华冠旁
西城区 志高空调
北三环中路辅路25号英斯泰克大厦3 层
东城区 海淀区
丰台区
空调配件 惠而浦(紫竹桥苏宁易购 店)
长虹电器北京销售公司
天坛路一号楼底商1-3号 北洼路4号苏宁易购紫竹桥店
东小口镇龙锦二街44-2至44-32号扬 州修脚旁

三菱电机空调故障代码

三菱电机空调故障代码

1三菱电机空调故障代码2014-11-11 故障代码故障内容 适用型号 E1操作开关线断、室内机电路板不良。

机型FDF505HES E2室内机位置编号重复、室内机电路板不良。

E3无对应室外机号码内外信号线断、室外机电源OFF E4室内机号码设定不正确(设定了48或49)室内机电路板不良。

E5室内机、室外机通讯异常、室外机电源部分异常(室外机室内机电源分开时)、 E6室内机热交换器热敏电阻不良、室内机电路板不良。

E7 室内机吸气热敏电阻不良、室内机电路板不良。

E8 内机热交换器温度高(暖气时)、室内机热交换用热敏电阻短路、室内机电路板不良。

E10 操作开关多台控制时台数超过。

E31 室外机号码重复、室外机电路板不良。

E32 电源反相或缺T 相(初级)、室外机电路板不良。

E33 压缩机过电流、压缩机缺S 相或R 相(初级52C 的次级配线) 故障代码 故障内容适用型号 E1 操作开关线断、室内机电路板不良。

机型FDF304HEN 、FDF504HES E2 室内机位置编号重复、室内机电路板不良。

E3 无对应室外机号码内外信号线断、室外机电源OFFE4 室内机号码设定不正确(设定了48或49)室内机电路板不良。

E5 室内机、室外机通讯异常、室外机电源部分异常(室外机室内机电源分开时)、 E6 室内机热交换器热敏电阻不良、室内机电路板不良。

E7 室内机吸气热敏电阻不良、室内机电路板不良。

E8 内机热交换器温度高(暖气时)、室内机热交换用热敏电阻短路、室内机电路板不良。

E10 操作开关多台控制时台数超过。

E31 室外机号码重复、室外机电路板不良。

E32 电源反相或缺T 相(初级)、室外机电路板不良。

E33 压缩机过电流、压缩机缺S 相或R 相(初级52C 的次级配线) E34 52C 的次级缺T 相、室外机电路板不良。

E35 室外机热交换器温度高(冷气时)、室外机热交换器用热敏电阻不良(短路)、室外机电路板不良。

三菱电机家用中央空调室内机风管机安装说明书

三菱电机家用中央空调室内机风管机安装说明书

PART NO. 9373385066-02E n g l i s hINSTALLATION MANUALVRF SYSTEM INDOOR UNIT Duct TypeFor authorized service personnel only.Contents1. SAFETY PRECAUTIONS .............................................22. ABOUT THE UNIT2.1. Precautions for using the R410A refrigerant ..........22.2. Special tool for R410A ............................................22.3. Accessories ............................................................22.4. Optional parts .........................................................33. INSTALLATION WORK3.1. Selecting an installation location ............................33.2. Installation dimensions ...........................................43.3. Installing the unit ....................................................44. PIPE INSTALLATION4.1. Selecting the pipe material .....................................74.2. Pipe requirement ....................................................74.3. Flare connection (pipe connection) ........................74.4. Installing heat insulation .........................................85. INSTALLING DRAIN PIPES (8)6. ELECTRICAL WIRING6.1. Electrical requirement ..........................................106.2. Wiring method ......................................................116.3. Unit wiring ............................................................116.4. Connection of wiring .............................................136.5. Air fl ow changing ..................................................137. FIELD SETTING7.1. Setting the address ..............................................147.2. Custom code setting ............................................157.3. Function setting ....................................................168. TEST OPERATION8.1. Test operation using PCB (Outdoor unit) .............178.2. Test operation using Remote Controller ...............179. CHECK LIST ...............................................................1710. ERROR CODES (17)1. SAFETY PRECAUTIONS• Be sure to read this Manual thoroughly before installation.• The warnings and precautions indicated in this Manual contain important information pertaining to your safety. Be sure to observe them.• Hand this Manual, together with the Operating Manual to the customer.Request the customer to keep them on hand for future use, such as for relocating or repairing the unit.WARNING!This mark indicates procedures which, if improperly performed, might lead to the death or serious injury of the user.• Request your dealer or a professional installer to install the unit in accordance with this Manual.An improperly installed unit can cause serious accidents such as water leakage, electric shock, or fi re.If the unit is installed in disregard of the instructions in the Installation Manual, it will void the manufacturer’s warranty.• Do not turn ON the power until all work has been completed.Turning ON the power before the work is completed can cause serious accidents such as electric shock or fi re.• If refrigerant leaks while work is being carried out, ventilate the area.If the refrigerant comes in contact with a flame, it produces a toxic gas.• Installation work must be performed in accordance with national wiring standards by authorized personnel only.CAUTION!This mark indicates procedures which, if improperly performed, might possibly result in personal harm to the user, or damage to property.2. ABOUT THE UNIT2.1. Precautions for using the R410ArefrigerantWARNING• Do not introduce any substance other than the prescribed refrigerant into the refrigeration cycle.If air enters the refrigeration cycle, the pressure in the refrigeration cycle will become abnormally high and cause the piping to rupture.• If there is a refrigerant leakage, make sure that it does not exceed the concentration limit.If a refrigerant leakage exceeds the concentration limit, it can lead to accidents such as oxygen starvation.• Do not touch refrigerant that has leaked from the refrigerant pipe connections or other area. Touching the refrigerant directly can cause frostbite.• If a refrigerant leakage occurs during operation, immediately vacate the premises and thoroughly ventilate the area.If the refrigerant comes in contact with a flame, it produces a toxic gas.2.2. Special tool for R410AWARNING• To install a unit that uses the R410A refrigerant, use dedicated tools and piping materials that have been manufactured specifi cally for R410A use.Because the pressure of the R410A refrigerant is approximately 1.6 times higher than the R22, failure to use dedicated piping material or improper installation can cause rupture or injury.Furthermore, it can cause serious accidents such as water leakage, electric shock, or fi re.Tool name Contents of changeGauge manifold• Pressure is huge and cannot bemeasured with a conventional gauge.To prevent erroneous mixing of otherrefrigerants, the diameter of each porthas been changed.It is recommended to use a gaugemanifold with a high pressure displayrange –0.1 to 5.3 MPa and a lowpressure display range –0.1 to 3.8 MPa. Charging hose• To increase pressure resistance, thehose material and base size werechanged.Vacuum pump• A conventional vacuum pump can beused by installing a vacuum pumpadapter.Gas leakagedetector• Special gas leakage detector for HFCrefrigerant R410A.2.3. AccessoriesWARNING• For installation purposes, be sure to use the parts supplied by the manufacturer or other prescribed parts.The use of non-prescribed parts can cause serious accidents such as the unit to fall, water leakage, electric shock, or fi re.• The following installation parts are furnished. Use them as required.• Keep the Installation Manual in a safe place and do not discard any other accessories until the installation work has been completed.En-2Binder (Medium)Coupler heat insulation (Small)Coupler heat insulation (Large)Special nut A(Large flange)Special nut B(Small flange)HangerHose bandDrain hose insulationEn-4CAUTION• Do not use the unit for special purposes, such as storing food, raising animals, growing plants, or preserving precision devices or art objects.It can degrade the quality of the preserved or stored objects.• Do not install where there is the danger of combustible gas leakage.• Do not install the unit near a source of heat, steam, or fl ammable gas.• Install the unit where drainage does not cause any trouble.• Install the indoor unit, outdoor unit, power supply cable, transmission cable, and remote control cable at least 1 m away from a television or radio receivers. The purpose of this is to prevent TV reception interference or radio noise.(Even if they are installed more than 1 m apart, you could still receive noise under some signal conditions.)• If children under 10 years old may approach the unit, take preventive measures so that they cannot reach the unit.• Decide the mounting position with the customer as follows:(1) Install the indoor unit on a place having a suf fi cient strength so that it withstands against the weight of the indoor unit.(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all over the room.(3) Leave the space required to service the air conditioner.(4) A place from where the air can be distributed evenly throughout the room by the unit.(5) Install the unit where connection to the outdoor unit is easy.(6) Install the unit where the connection pipe can be easily installed.(7) Install the unit where the drain pipe can be easily installed.(8) Install the unit where noise and vibrations are not ampli fi ed.(9) Take servicing, etc., into consideration and leave the spaces. Also install the unit where the fi lter can be removed.(10) Providing as much space as possible between the indoorunit and the ceiling will make work much easier.(11) If installing in a place where its humidity exceeds 80%, useheat insulation to prevent condensation.3.2. Installation dimensions• Provide the space around the unit as shown in the following fi gure.400 mm or more 150 mm or more ❈1❈1 400mm or more when drain from drain pipe.• Provide a service hole for inspection purposes.• Do not place any wiring or illumination in the service space, as they will impede service.• When an air fi lter is installed on the air inlet, provide enough service space to replace the fi lter.AirAirService holeControl box300 mmor more 500 mm or more500 m m o r m o r e100 m mAir AirService spaceControl box300 mm or more1,550 mm or more500 m m o r m o r e100 m mIntake panel3.3. Installing the unitWARNING• Install the air conditioner in a location which can withstand a load do at least fi ve times the weight of the main unit and which will not amplify sound or vibration. If the installation location is not strong enough, the indoor unit may fall and cause injuries.• If the job is done with the panel frame only, there is a risk that the unit will come loose. Please take care.3.3.1. Installing the hangersHanging bolt installation diagram.(Top side)(Right side)270 m mA i rA i rWARNING• When fastening the hangers, make the bolt positionsuniform.740 mm477 mmA i rA i r1,135 m m1,177 m mDuct installation pattern ( CUT PART)Cut Cut Cut Cut(2) Turn up the insulation around the points to be cut ac-cording to the outlet port shape working points so thatthe insulation does not stick out at the(3) Cut with nippers and remove the sheet metal.• The screw holes to install the flange are located behind the round cutouts in the insulation.Duct4.PIPE INSTALLATIONCAUTION• Be more careful that foreign matter (oil, water, etc.) does not enter the piping than with refrigerant R410A models. Also, when storing the piping, securely seal the openings by pinching, taping, etc.• While welding the pipes, be sure to blow dry nitrogen gas through them.4.1. Selecting the pipe materialCAUTION• Do not use existing pipes.• Use pipes that have clean external and internal sides without any contamination which may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or water.• It is necessary to use seamless copper pipes.Material : Phosphor deoxidized seamless copper pipesIt is desirable that the amount of residual oil is less than 40 mg/10 m.• Do not use copper pipes that have a collapsed, deformed, or discolored portion (especially on the interior surface). Otherwise, the expansion valve or capillary tube may become blocked with contaminants.• Improper pipe selection will degrade performance. As an air conditioner using R410A incurs pressure higher than when using conventional refrigerant, it is necessary to choose adequate materials.• Thicknesses of copper pipes used with R410A are as shown in the table.• Never use copper pipes thinner than those indicated in the table even if they are available on the market. Thicknesses of Annealed Copper Pipes (R410A)Pipe outside diameter [mm (in.)]Thickness [mm]6.35 (1/4)0.809.52 (3/8)0.8012.70 (1/2)0.8015.88 (5/8) 1.0019.05 (3/4) 1.204.2. Pipe requirementCAUTION• Refer to the Installation Manual of the outdoor unit for description of the length of connecting pipe or for difference of its elevation.• Use pipe with water-resistant heat insulation.CAUTION• Install heat insulation around both the gas and liquid pipes.Failure to do so may cause water leaks.Use heat insulation with heat resistance above 120 °C.(Reverse cycle model only)In addition, if the humidity level at the installation location of the refrigerant piping is expected to exceed 70 %, install heat insulation around the refrigerant piping. If the expected humidity level is 70-80 %, use heat insulation that is 15 mm or thicker and if the expected humidity exceeds 80 %, use heat insulation that is 20 mm or thicker. If heat insulation is used that is not as thick as specified, condensation may form on the surface of the insulation. In addition, use heat insulation with heat conductivity of 0.045 W/(m·K) or less (at20 °C).4.3. Flare connection (pipe connection)WARNING• Tighten the flare nuts with a torque wrench using the specified tightening method. Otherwise, the flare nuts could break after a prolonged period, causing refrigerant to leak and generate a hazardous gas if the refrigerant comes into contact with a fl ame.4.3.1. Flaring• Use special pipe cutter and fl are tool exclusive for R410A. (1) Cut the connection pipe to the necessary length with apipe cutter.(2) Hold the pipe downward so that cuttings will not enter thepipe and remove any burrs.(3) Insert the fl are nut (always use the fl are nut attached tothe indoor and outdoor units respectively) onto the pipeand perform the flare processing with a flare tool. Usethe special R410A flare tool, or the conventional flaretool. Leakage of refrigerant may result if other fl are nutsare used.(4) Protect the pipes by pinching them or with tape toprevent dust, dirt, or water from entering the pipes.BDieAPipeCheck if [L] is flared uniformlyand is not cracked or scratched.LEn-7Width across4.3.2. Bending pipesIf pipes are shaped by hand, be careful not to collapsethem.Do not bend the pipes in an angle more than 90°.When pipes are repeatedly bend or stretched, the material will harden, making it dif more.Do not bend or stretch the pipes more than three times.Connection pipeTorque wrenchIndoor unit pipe Flare nutHolding wrenchTighten with two wrenches.(Accessories)Binder (Large)(Accessories)Heat insulationheat insulation.CAUTION• After checking for gas leaks (refer to the Installation Manual of the outdoor unit), perform this section.• Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do so may cause water leaks.INSTALLING DRAIN PIPESUse general hard polyvinyl chloride pipe and connect it withadhesive (polyvinyl chloride) so that there is no leakage.Always heat insulate the indoor side of the drain e a drain hose that matches the size of the drain pipe.Do not perform a rise, trap and air bleeding.Provide a downward gradient (1/100 or more).Provide supporters when long pipes are installed.Use an insulation material as needed, to prevent the pipes from freezing.Install the pipes in a way that allows for the removal of the control box.Drain port Drain cap(Accessories)• Cover the drain cap with the drain hose insulation.Drain hose insulation (Accessories)Unit Unit Drain hose insulation (Accessories)Drain cap0 mmINSTALL THE DRAIN HOSEWorking procedure1) Install the attached drain hose to the drain port of the body.Install the hose band from the top of the hose within the graphic display area. Secure fi rmly with the hose brnd.2) Use vinyl adhesive agent to glue the drain piping (PVC pipe VP25) which is prepared on site or socket. (Apply color ad-hesive agent evenly until the gauge line and seal)3) Check the drainage.4) Install the heat insulation.5) Use the attached heat insulation to insulate the drain port and band parts of the body.DrainhoseArrange the drain hoselower than this portionTrapNO GOODOKRiseNO GOOD1.5 to2.0 mAir bleedingNO GOODCAUTION• Always check that the drain cap is installed to the unused drain port and is fastened with the binder.If the drain cap is not installed, or is not suffi ciently fastened by the binder, water may drip during the cooling operation.6.ELECTRICAL WIRING6. E L E C T R I C A L WWARNING• Electrical work must be performed in accordance with this Manual by a person certified under the national or regional regulations. Be sure to use a dedicated circuit for the unit.An insufficient power supply circuit or improperly performed electrical work can cause serious accidents such as electric shock or fi re.• Before starting work, check that power is not being supplied to the indoor unit and outdoor unit.• For wiring, use the prescribed type of wires, connect themEn-116.2. Wiring method(EXAMPLE)PR SUPPLY OUTDOOR UNIT TRANSMISSIONTRANSMISSION TRANSMISSION POWER SUPPLYPOWER SUPPLY POWER SUPPLYPOWER SUPPLYPOWER SUPPLYREMOTE CONTROL UNIT (MASTER)REMOTE CONTROL UNIT (SLAVE)REMOTE CONTROL UNITREMOTE CONTROLINDOOR UNITINDOOR UNIT INDOOR UNITBREAKERBREAKER POWER SUPPLY REMOTE CONTROLPOWER SUPPLY REMOTE CONTROLBREAKER BREAKERTRANSMISSION 6.3. Unit wiring• Before attaching the cable to terminal block.6.3.1. Power supply cablePower supply cable25 mm Earth cable30m m A. For solid core wiring(1) To connect the electrical terminal, follow the below diagram and connect after looping it around the end of the cable. (2) Use the speci fi ed cables, connect them securely, and fasten them so that there is no stress placed on the terminals.(3) Use an appropriate screwdriver to tighten the terminal screws. Do not use a screwdriver that is too small, otherwise, the screw heads may be damaged and prevent the screws from being properly tightened.(4) Do not tighten the terminal screws too much, otherwise, the screws may break.(5) See the table for the terminal screw tightening torques.(6) Please do not fi x two power supply cables with one screw.St ri p 25 mmLoop Screw with spe-cial washerScrew with special washer Cable end(Loop)Cable end (Loop)CableCableTerminal blockWARNING• When using solid core cables, do not use the ring terminal. If you use the solid core cables with the ring terminal, the ring terminal's pressure bonding may malfunction and cause the cables to abnormally heat up.B. For strand wiring(1) Use ring terminals with insulating sleeves as shown in the fi gure below to connect to the terminal block.(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the cables do not come loose.(3) Use the speci fi ed cables, connect them securely, and fasten them so that there is no stress placed on the terminals.(4) Use an appropriate screwdriver to tighten the terminal screws. Do not use a screwdriver that is too small, otherwise, the screw heads may be damaged and prevent the screws from being properly tightened.(5) Do not tighten the terminal screws too much, otherwise, the screws may break.(6) See the table for the terminal screw tightening torques.(7) Please do not fi x two power supply cables with one screw.St r i p10 mmSleeveScrew with special washerScrew with special washerRing terminalCableCableTerminal blockRing terminalRing terminalWARNING• Use ring terminals and tighten the terminal screws to thespeci fi ed torques, otherwise, abnormal overheating may be produced and possibly cause heavy damage inside the unit.Tightening torqueM4 screw(Power supply /L, N, GND) 1.2 to 1.8 N·m (12 to 18 kgf·cm)En-126.3.2. Transmission and Remote control cableTransmission cableShielded cable (No fi lm)20 mm 45m mRemote control cable20 m m• Connect remote control and transmission cables as shown in Fig. A.Fig. AScrew Terminal blockCableCable of the same caliber: OKCable of the different caliber: NO GOODWARNING• Tighten the terminal screws to the specified torques, otherwise, abnormal overheating may be produced and possibly cause heavy damage inside the unit.Tightening torqueM3.5 screw(Transmission /X1, X2)(Remote control /Y1, Y2, Y3)0.8 to 1.0 N·m (8 to 10 kgf·cm)CAUTION• To peel the fi lm from the lead cable, use a dedicated tool that will not damage the conductor cable.• When installing a screw on the terminal block, do not cut the cable by overtightening the screw. On the other hand, an undertightened screw can cause faulty contact, which will lead to a communication failure.En-136.4. Connection of wiring(1) Remove the control box cover and install each connection cable.ScrewControl box cover(2) After wiring is complete, secure the remote control cable, connection cable, and power cable with the cable clamps.Power supply cable (Field supply)Binder (Medium) (Accessories)Binder (Medium) (Accessories)Remote control cable Transmission cable (Field supply)Binder (Medium) (Accessories)L, N:Power supply cableX1, X2:Transmission cableRemote control cable Y1:Red Y2:White Y3:Black6.5. Air fl ow changingWhen using the ARXB24/30/36/45L model with external Static Pressure under 40 Pa, the Wire (FAN MOTOR) must be replaced as explained below.Replacement method (1) Remove the cover.(2) Remove the Wire (TYPE A) connector from Wire (FAN MOTOR).(3) Remove the Wire (TYPE A) connector from CN4 of the PCB.(4) Insert the Wire (TYPE B) connector into CN4 of the PCB.(5) Insert the Wire (TYPE B) connector into Wire (FAN MOTOR).(6) Insert the cover.En-147.1. Setting the addressCAUTION• Use an insulated screwdriver to set the dip switches.Rotary switch Example: “0”Dip switch “SET 3”Rotary switch Example: “0”SW 1SW 2SW 3SW 4SettingSetting rangeType of switchIndoor unit address0–63Setting example2IU AD X 10 IU AD X 1Refrigerant circuit address0–99Setting example 63REF AD X 10 REF AD X 1(1) Indoor unit addressRotary switch (IU AD x 1)...Factory setting “0” Rotary switch (IU AD x 10)...Factory setting “0”When connecting multiple indoor units to one refrigerant system, set the address at IU AD SW as shown in the T able A.(2) Refrigerant circuit addressRotary switch (REF AD x 1)...Factory setting “0” Rotary switch (REF AD x 10)...Factory setting “0”In the case of multiple refrigerant systems, set REF AD SW as shown in the Table A for each refrigerant system.Set to the same refrigerant circuit address as the outdoor unit.• If working in an environment where the wireless remote controller can be used, the addresses can also be set using the remote controller.• If setting the addresses using the wireless remotecontroller, set the indoor unit address and refrigerant circuit address to “00”.(For information on setting using the wireless remote controller.)CoverWire (Fan motor)External Static Pressure and Required Connector TypeType ABExternal Static Pressure40 – 80 Pa0 – 40 PaWire123456123451 BLACK2 WHITE3 PINK4 PURPLE5 BLUEARXB24 ARXB30 ARXB361 BLACK 2 WHITE 3 RED 4 BLUE 5 PINK 6 PURPLEARXB451 BLACK2 WHITE3 RED4 PINK5 PURPLE6 BLUERemarkFactory setting (Standard static pressure)Accessories (Low static pres-sure)7. FIELD SETTING• Refer to the following three items for setting the FIELD SETTING address. The respective settings are included below.(1) IU AD, REF AD SW settings ............ T his section (2) Remote control settings ................... R efer to the wired orwireless remote control manual for detailed set-ting information. (Set IU AD, REF AD SW to 0)(3) Automatic address settings .............. R efer to the indoor unitmanual for detailed set-ting information. (Set IU AD, REF AD SW to 0)CAUTION• Be sure to turn OFF the power before performing the fi eld setting.Table AAddressRotarySwitch SettingAddressRotarySwitch SettingRefrigerant circuit REF AD SWIndoor unitIU AD SW x 10x 1x 10x 1000000 101101 202202 303303 404404 505505 606606 707707 808808 909909 10101010 11111111 12121212.. ................99996363 Do not set the indoor unit address (IU AD SW) at 64 to 99. It may result failure.RC AD SWRC AD SW1RC AD SW2RC AD SW3Indoor unitRemotecontrollerIndoor unit Indoor unit Indoor unitA B C DA B C D IndoorunitRemotecontrollerConfusionCode change(3) Remote controller addressRotary switch (RC AD SW)...Factory setting “0”When connecting multiple indoor units to one standard wired remote controller, set the address at RC AD SW in sequence from 0.SettingSettingrangeType of switchRemotecontrolleraddress0–15SettingexampleRC ADExample If 4 indoor units are connected.RC AD SW01234567 Address01234567RC AD SW89A B C D E F Address891011121314157.2. Custom code settingSelecting the custom code prevents the indoor unit mix-up.(Up to 4 codes can be set.)Perform the setting for both the indoor unit and the remote controller.En-15En-16Function detailsFunctionFunction numberSetting number DefaultDetailsFilter indicator interval1100Default ○Adjust the fi lter cleaning interval noti fi cation. If the noti fi cation is too early, change to setting 01. If the noti fi cation is too late, change to setting 02.01Longer 02Shorter Filter indicator action1300Enable ○Enable or disable the fi lter indicator. Setting 02 is for use with a central remote control.01Disable 02Display only on central remote control Horizontal swing air fl ow direction2400Default ○Adjust the horizontal swing air fl ow direction.(For horizontal swing equipped models)01Left half 02Right half Cool air temperature trigger3000Default ○Adjust the cool air trigger temperature. To lower the trigger temperature, use setting 01. To raise the trigger temperature, use setting 02.01Adjust (1)02Adjust (2)Hot air temperature trigger3100Default ○Adjust the hot air trigger temperature. To lower the trigger temperature by 6 degrees C, use setting 01. To lower the trigger temperature by 4 degrees C, use setting 02. To raise the trigger temperature, use setting 03.01Adjust (1)02Adjust (2)03Adjust (3)Auto restart4000Enable Enable or disable auto-matic system restart after a power outage.01Disable○External control4600Start/Stop○Allow an external control-ler to start or stop the system, or to perform an emergency shutdown.* I f an emergency shut-down is performed from an external controller, all refrigerant systems will be disabled.01Emergen-cy stopError report target4700All ○Change the target for reporting errors. Errors can either be reported in all locations, or only on the wired remote.01Display only on central remote control• Custom code setting for indoor unitSet the DIP SW SET 3 SW1, SW2, referring to the Table B.Dip switch “SET 3”SW 1SW 2SW 3SW 4OFFON Table BCustom codeA (Factory setting)BC D DIP SWSET 3 SW1OFF ON OFF ON DIP SW SET 3 SW2OFFOFFONON7.3. Function setting• FUNCTION SETTING can be performed with the wired or wireless remote control.(The remote control is optional equipment)• Refer to the wired or wireless remote control manual for detailed setting information. (Set IU AD, REF AD SW to 0)• Refer to “7.1. Setting the address” for indoor unit ad-dress and refrigerant circuit address settings.• T urn the power of the indoor unit ON before starting the setting.* Turning on the power indoor units initializes EEV , so make sure the piping air tight test and vacuuming have been conducted before turning on the power.* Also check again to make sure no wiring mis-takes were made before turning on the power.。

三菱空调机维修手册

三菱空调机维修手册

号符的用使中图插
。损受调空或害伤身人致导能可有�示指有所守遵不若 �意注 。亡死或害伤身人重严致导能可有�示指有所守遵不若 �告警
号符的用使中文正
。全安保确�守遵以予必务请。息信要重的全安的关有了供提项事意注些这 。容内部全的项事意注全安列下读阅细仔必务请�前之调空装安在
项事意注全安
-2-
。用作起不 器测检气漏的机冷制统传于用适故�氯含不A014R因 。质变媒冷致导会�合混A014R与水者或�合混 A014R与油机媒冷或�和媒冷的上具工些这在留残如 • • 。质变油机媒冷致导会物染污的内管配媒冷 •
。装安员人业专由交请
。签标的贴上机主读阅细仔�告警
。户用的新给交册手本将请�时更变员人的器机用使�外另 。员人工施给交其将请�时器机理修或移迁在。阅取时随备以�管保善妥册手本将终始应户用机本 。员人的机本用使给交其将必务请�后册手本完读阅
〉色黄�色颜〈�。上签标的机主在现出号符该�电触心小 : 。件部的地接须必示表 : 。示指要重的守遵须必示表 : 。作动的免避须必示表 :
。险危 有�利锋片热散�片热散的器换交热碰触接直手用勿请
。签标的贴上机主读阅细仔�告警
-3-
。气漏或水漏致导会能可�器机用使下境环的�等酸 、物合化硫含、水氨如�体气蚀腐、剂溶机有有在果如 。火起或烟冒、电触发引能可并�障故或�和降 下著显能性致导会能可机本用使下境环的剂雾喷型 。统 系水排中集装安机外室为虑考可�水滴机外室止防为 。水滴 会能可机内室�时塞堵统系水排者或%08过超度湿当 • 。量质的品物述上持保以件条足充供提法无机本 • • 类殊特用使或剂溶性碱、性酸、汽蒸、油量大有在 • •
。物染污等分水和油、屑切、垢污�尘 灰、物化氧、磺硫如诸何任有没保确�洁清的壁外和壁 内管配持保。管配媒冷的成制铜氧脱磷0 221C类�管金 合铜缝无及管铜缝无�0003H由用采需�准标SIJ据根

苏州大金三菱电机东芝与三菱重工中央空调的比较

苏州大金三菱电机东芝与三菱重工中央空调的比较

苏州大金、三菱电机、东芝与三菱重工中央空调的比较三菱重工中央空调与其他品牌粗略比较(客观分析的态度)一、与大金:1、大金各个系列的产品已经完全国产化,机器材质、装配制造工艺都不能和以前相比,质量下滑很严重,导致大金返修率偏高;三菱重工高端机型属于组装机,压缩机日本产,内、外机重要零部件日本进口,同时说明下,日本进口率是比较低的。

(有兴趣的客户可以到工地或者大金实体店去看看样机,质量怎么样,相信你心中有杆秤)2、大金制热效果欠缺(这个整个暖通行业、装修行业公认的事实,大金的经销商也是承认的,冬天需要地暖供热);三菱重工制热、制冷效果没有任何问题(安装正常情况下),零下-10度,出风口温度50度以上,室内恒温28度左右。

3、大金噪音25分贝偏高,安装送回风方式不采用后回风30分贝。

三菱重工21分贝,实际使用效果业内最低,声音很低很轻(21分贝是制冷量最小的内机、低风模式下)。

4、大金内机标配无冷凝水提升泵;三菱重工内机均配置高扬程冷凝水提升泵(90公分扬程)二、与三菱电机:1、三菱电机内机型号少,机器笨重,厚度20公分,深度70公分;日立内机型号多,厚度19.2公分,深度44.7公分,三菱重工内机更加小巧。

2、三菱电机噪音偏大(实际使用比大金、日立噪音都要响),经销商多次向厂家反映,三菱电机中央空调生产量相对壁挂机要少的多,市场占有率低,并没有引起厂家的重视,一直未作改进)。

3三菱菱耀系列分歧箱连接方式,是菱尚系列(多管制)与菱睿系列(分歧管)之间的过渡产品,分歧箱连接导致管道的浪费、内机效果的衰减、打孔孔径大、数量多;菱睿系列是三菱电机技术最成熟、最新型、价格最贵的产品系列,三菱重工采用分歧管连接。

4、三菱电机菱尚、菱耀系列上海生产,菱睿系列压缩机部分泰国进口。

5、三菱电机菱尚、菱耀系列采用第三代涡旋式低压腔压缩机,菱睿系列采用高压腔压缩机,三菱重工第三代压缩机全部都是高压腔。

(低压腔增加能耗和故障隐患)6、三菱电机菱尚系列5B120的机器实际使用效果性能很不稳定,2012年各级经销商已经暂停销售。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

空调使用时间久了难免会出现故障,你知道空调的维修方法吗?下面咱们一起来看看使用三菱电机空调时的注意事项,和一些常见的故障维修方法:
1.现象:空调系统不工作且空调的压缩机不吸合。

成因:制冷剂部分或全部泄露。

维修:找出导致制冷剂泄漏的故障点,并更换损坏的零件,然后重新将其抽成真空状态,再添加适量的制冷剂。

容易发生制冷剂泄漏的部位有:管路及其密封圈、冷凝管、膨胀阀、压力开关等。

2.现象:空调不能制冷,压缩机能够吸合,但低压很低且排出管表面温度极高。

成因:膨胀阀上的感温头损坏,导致冷媒泄漏无法制冷。

维修:将坏掉的感温头换掉,并将系统抽成真空、保压,然后根据空调规定的剂量适量添加制冷剂。

注意事项:
1、空调使用季节,内机过滤网每个月用自来水清洗一次,内机冷凝器每个
季度用专用的泡沫清洁剂清洁一次,外机散热器每个季度用自来水冲洗一次。

2、较长时间不使用时,要拔下插头,一是不浪费待机耗电,二是用电安全。

3、温度设定不要与环境温度相差过大,以免压缩机连续运转不停机,磨损大耗电大。

4、空调不使用季节,除了电源插头拔下外,遥控器的电池要取下,以防漏液锈蚀。

5、遇到内机的指示灯全部跳闪,是自检报警和压缩机保护报警,立即拔下插头,报修。

6、机器正常使用,不发生系统管路泄漏的,制冷剂不会随使用时间损耗。

7、空调器室外散热器上积灰太多会使效率下降,应定期检查和清扫室外散热器(在停电后进行,可用压缩空气吹净);
8、分体式空调器室外机组不可用棍棒类物体插入,否则风扇将被卡住或损坏;
9、当感到空调器使用不理想时应查阅使用说明书,分析是否因使用不当而
引起,查明原因后进行纠正;
10、发现故障后不能自行处理时,可找原安装部门的专业维修技工解决,或与该品牌公司当地服务人员联系,不可自行修理或找非专业人员检修;
11、空调器不使用时应及时拔掉电源;
12、空调器停机后必须待三分钟后再次启动,以保护压缩机;
13、带有遥控器(不应放在小孩易取之处)的空调器在使用中不要被小孩当成玩具操作,以免损坏机器。

能够在一定的范围内连续调节压缩机的频率或转速,即可改变制冷剂的流量,而发挥最能与环境状态相匹配的能力而自动调节输出的新型空调器。

变频空调器采用数字信号处理和模拟控制与人工智能控制相结合。

与普通空调相比,变频空调具有制冷制热迅速强劲,高效节能,舒适可靠,智能除霜,除湿量大,超静音,宽电压工作等优点。

以家电、家居生活为主营业务方向,提供小家电、热水器、空调、燃气灶、油烟机、冰箱、洗衣机、电视、开锁换锁、管道疏通、化粪池清理、家具维修、房屋维修、水电维修、家电拆装等保养维修服务。

相关文档
最新文档