LINUX系统安装后的初始环境设置

合集下载
  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

前言

在 CentOS 安装好之后,安全性以及对硬件的适应性方面,可能并不完全符合我们的实际情况。在这里,对新的 CentOS 系统进行初始环境设置将以如下方面为原则:

1,为了安全,尽最大可能将访问限制限制到可能的最大程度;

2,为了节省内存及 CPU 使用率(以及安全方面的考虑),尽最大可能将不需要的服务关闭;

3,为了减少误操作可能带来的损失,平时通过 wheel 组用户登录进行系统管理;

4,为了让系统变的更加轻便、快速,将内核中不需要的模块卸载;

…………

CentOS 4.4 的安装后初始环境设定

安装完毕重新启动系统后,出现如下的状态:

CentOS release 4.4 (Final)

Kernel 2.6.9-42.EL on an i686

sample login: ← 根据安装时网络设置的情况的不同,本站以“sample”,其位置显示的是你设置好的主机名。

[1] 系统的登录与退出

sample login: root ← 用root用户来登录系统,输入用户名root

Password: ← 在这里输入安装时设置的root密码,输入时密码不会被显示

[root@sample ~]# ← root用户登录成功,提示符为“#”。若一般用户登录成功后,提示符为“$”

[root@sample ~]# exit ← 退出系统

sample login: ← 退出系统成功

[2] 一般用户的建立与删除

[root@sample ~]# useradd centospub ← 建立用户名为 centospub 的一般用户

[root@sample ~]# passwd centospub ← 为用户 centospub 设置密码

Changing password for user centospub.

New UNIX password: ← 输入密码(密码不会被显示)

Retype new UNIX password: ← 再次输入密码确认两次密码一致

passwd: all authentication tokens updated successfully. ← 密码设置成功

[root@sample ~]# userdel -r centospub ← 删除用户名为 centospub 的一般用户

[3] 通过一般用户登录为root用户

因为root用户对系统具有全权的操作权限,为了避免一些失误的操作,建议在一般情况下,以一般用户登录系统,必要的时候需要root操作权限时,再通过“su -”命令来登录为root用户进行操作。

[centospub@sample ~]$ ← 提示符为“$”,说明当前状态为一般用户centospub登录在系统中

[centospub@sample ~]$ su - ← 输入登录为root用户的命令

Password: ← 输入root密码(密码不会被显示),回车

[root@sample ~]# ← 成功登录为root用户,提示符变为“#”

[root@sample ~]# exit ← 回到一般用户的登录状态

[centospub@sample ~]$ ← 提示符变为“$”,回到了一般用户centospub登录系统的状态

[4] 建立管理员组内一般用户

在一般情况下,一般用户通过执行“su -”命令、输入正确的root密码,可以登录为root用户来对系统进行管理员级别的配置。但是,为了更进一步加强系统的安全性,有必要建立一个管理员的组,只允许这个组的用户来执行“su -”命令登录为root用户,而让其他组的用户即使执行“su -”、输入了正确的root密码,也无法登录为root用户。在UNIX下,这个组的名称通常为“wheel”。

[root@sample ~]# usermod -G wheel centospub ← 将一般用户 centospub 加在管理员组wheel组中

[root@sample ~]# vi /etc/pam.d/su ← 打开这个配置文件

#auth required /lib/security/$ISA/pam_wheel.so use_uid ← 找到此行,去掉行首的“#”

auth required /lib/security/$ISA/pam_wheel.so use_uid ← 变为此状态(大约在第6行的位置)

[root@sample ~]# echo "SU_WHEEL_ONLY yes" >> /etc/login.defs ← 添加语句到行末

以上操作完成后,可以再建立一个新用户,然后用这个新建的用户测试会发现,没有加入到wheel组的用户,执行“su -”命令,即使输入了正确的root密码,也无法登录为root用户。

[5] 建立PPPoE连接(非xDSL接入方式的用户可跳过此步骤)

[root@sample ~]# adsl-setup ← 建立ADSL连接

Welcome to the ADSL client setup. First, I will run some checks on

your system to make sure the PPPoE client is installed properly...

LOGIN NAME

Enter your Login Name (default root): ← 填入ADSL连接的用户名

INTERFACE

Enter the Ethernet interface connected to the ADSL modem

For Solaris, this is likely to be something like /dev/hme0.

For Linux, it will be ethX, where 'X' is a number.

(default eth0): ← 指定网络接入设备,一块网卡的情况下,一般为默认eth0

Do you want the link to come up on demand, or stay up continuously?

If you want it to come up on demand, enter the idle time in seconds

after which the link should be dropped. If you want the link to

stay up permanently, enter 'no' (two letters, lower-case.)

相关文档
最新文档