PA2005说明书
楼宇对讲主机使用说明书

楼宇对讲主机使用说明书简介 1功能说明 4外观描述 2接线端示意图 3目 录目录安装说明 8技术规格 8保养说明保养说明及注意事项:1.防水防潮,避免污物和过多的灰尘,室内分机应安装在 干燥清洁的地方,以免内部元器件受潮及其他杂物进入 机内;2.勿让阳光直射,远离火源;3.远离强磁场;4.保持表面清洁,勿直接用水冲洗,忌用天那水苯汽油等 化学溶剂擦试;5.非本公司指定产品,不可配套使用;6.非专业人员不得擅自打开修理,须由本公司专业人员(或 本公司授权后,在本公司指导下)维修。
否则所有保修条 款将自动失效!套件清单:单元主机--------------------------------------1台 说明书-----------------------------------------1份 保修标贴--------------------------------------1份套件清单简 介产品简介主要应用于单元入口和单元地下停车场入口。
它具有主动呼叫住户、询问管理处、密码开锁、地址设置、状态提示和开锁方式选择、门禁控制、智能语音导航等功能。
本主机是小区联网系统中的单元门主机。
安装说明安装说明:1、根据单元主机的底箱的尺寸在要安装的位置挖一个长 方形的孔;2、将底箱固定在门上或固定在墙上;3、把各传输线按接线图要求连接好,注意分清极性及接线 的顺序,不能接错;4、用随机配备的螺丝将单元主机固定在底箱上;5、根据实际情况设置好单元主机的地址号。
技术规格:参数名称具体参数参数名称具体参数最大容量9999户工作电压DC12V ±0.5V线径要求彩色摄像机照度1.0Lux 静态电流70mA 环境温度-10℃~+55℃湿 度45%~95%无凝结面板尺寸350*156*8mm 黑白摄像机照度0.1Lux 底壳尺寸310*125*30mm技术规格国标超五类外观描述:外观描述摄像头序号功 能功 能1234567读卡区话筒显示屏键盘补光灯喇叭序号63功能说明显示“ -”),按“#”键退出;输入“4”进入按卡片序号删除设置项,屏幕显示“ ”, 主机发出“滴”一声提示音,屏幕显示“ ”,输入对 应四位序号(如:0001~6000),如果输入的序号正确主 机会自动删除卡片信息,删除成功时主机发出“滴”一声 提示音,如果删除不成功时主机发出“滴滴滴”几声提示 音;主机返回上一级操作清单(屏幕显示“ -”), 按“#”键退出;输入“5”进入联网ID 号设置项,屏幕显示“ .... ”, 输入对应二位序号(01~99),主机发出“滴”一声提示 音,表示设置成功,如果设置不成功时主机发出“滴滴 滴”几声提示音;主机返回上一级操作清单(屏幕显示 “ -”),按“#”键退出;输入“6”进入删除所有卡片设置项,屏幕显示“....”, 按“#”键进入确认删除所有卡片设置,主机进行卡片删 除操作,等待一段时间后主机发出“滴”一声提示音, 表示门禁模块内所有卡片资料已被删除(谨慎操作此项 功能,卡片资料删除后无法恢复),删除完成后系统自动 退出设置状态。
(完整word版)培训主管岗位职责及考核

培训主管职位说明书人力资源部培训主管业绩考核办法一、考核对象: 培训管理员。
二、考核内容及办法1.培训计划与培训制度的拟订(权重10分)2005年12月中旬前需将2006年度培训计划和培训费用预算上交部门总监;制定《酒店内部训导师管理条例》和《内部训导师授课费用实施办法》2-3月完成;制定年度优秀训导师评比办法1季度内完成。
制度拟草分为优秀8分、良好7-6分、合格5-4分、差3-1分, 权重8分。
依据年度员工培训计划制定酒店月度培训计划, 并于当月26日前报HR副总监审核, 每推后一天扣1分, 由人力资源副总监考核。
2.培训组织实施(权重35分)①月度培训计划执行率100%, 未按当月培训实施计划组织实施, 扣3分/项培训, 因客观原因无法按月度培训计划执行, 必须在当月20日前调整计划并组织实施, 否则扣2分/次, 权重10分, 由人力资源副总监考核;计算方法: 月度员工培训实际次数/月度员工培训计划数×100%②为员工培训及时提供培训内容教材提纲、讲师、场地、器材、后勤等各种服务, 提高培训质量, 培训时未提供完整的培训服务, 每缺一项扣1分, 因准备不充分导致培训终止, 扣5分/次, 权重15分, 由人力资源副总监考核;③培训记录、培训效果评估齐全真实, 每出现培训记录不真实, 扣0.5分/人次, 缺培训记录扣2分/次, 培训效果评估不真实(未由参训人员直接参与评估), 每次扣1分, 缺培训评估扣1分/次, 权重10分, 由人力资源副总监考核;④员工培训投诉率为零, 如因部门内部需要培训的而未提供培训服务或在实施培训中造成部门投诉, 每投诉一次扣1分, 权重5分, 由人力资源副总监考核。
3.培训管理(权重20分)①深入各部门进行培训需求调查, 每季度进行一次培训需求调查, 形成详细的培训需求调查, 于当季末月28日前交副总监, 并录入培训管理培训调查文件夹内, 每推后一天扣1分, 报告分为优秀6分、良好5-4分、合格3分、差2-1分, 权重6分, 由人力资源副总监考核;②每月根据培训情况, 在当月28日前完成培训分析报告, 指出培训存在的问题, 提出解决问题的办法, 并录入培训管理培训分析文件夹内, 每推后一天扣2分, 报告分为优秀6分、良好4-5分、差1-3分, 权重6分, 由人力资源副总监考核;③按月计划每月抽查各部门的培训计划执行不少60%;少于60%扣2分、少于50%扣4分;④建立员工培训档案, 并做好员工培训记录, 出现一般不合格项, 扣1分/项, 权重4分, 由HR 副总监考核。
派克液压密封件说明书

派克汉尼汾公司版权所有未经许可不能摘录,翻印。
保留修改权利2021年6月警告销售条件本样本中产品和/或系统或相关产品出现故障,选型不当或使用不当,均可能导致人身伤亡和财产损失。
本文档以及由派克·汉尼汾公司及其子公司和授权经销商提供的其他资料,为具有技术知识的用户提供进一步研究所需的产品和/或系统选项。
重要的是,用户必须对您的应用进行全面的分析,并对当前产品样本中与产品或系统相关的资料进行评估。
由于工作条件以及产品或系统的多样性,用户必须自行分析和测试,并独自承担一切后果,包括:产品和系统的最终选型以及确保满足应用的所有性能、安全和警告等方面的要求。
派克·汉尼汾及其子公司可能会随时对本样本中的产品,包括但不限于:产品的特性、产品的规格、产品的结构、产品的有效性以及产品的价格作出变更而不另行通知.本样本中的所有产品均由派克·汉尼汾公司及其子公司和援权经销商销售。
与派克签订的任何销售合同均按照派克标准条件和销售条件中规定的条款执行(提供复印件备索)。
本公司的密封件,只能在本公司的文件资料述及的应用参数范围与接触介质、压力、温度和存放时间相一致的情况下才能使用。
在规定的应用参数范围外使用以及错误选用不同的材料都可能导致密封件寿命的缩短以及设备的损坏,甚至更严重的后果(如生命安全,环境污染等)。
样本中所列出的工作压力、温度范围、运动速度是极限值,它们之间相互关联、相互影响;在极端的工况下,建议不要同时把各个参数都同时用到极限值。
对于特殊的要求(压力、温度、速度、介质等),请联系派克汉尼汾公司以咨询合适的密封结构、材料、配置、安装建议等。
由于诸多工作参数会影响到流体传动系统及密封元件,这些设备的制造商必须在实际工作条件下测试、验证并批准密封系统的功能与可靠性。
此外,对于不断出现的新的介质(液压油、润滑脂、清洗剂等),用户特别注意它们与目前所用的密封件弹性体材料的兼容性。
我们建议用户在大批量应用之前,在厂内或现场先做密封材料的兼容性能测试,作为密封产品与系统供应商,我们建议用户遵循我们的这些建议。
氨甲环酸片说明书

氨甲环酸片说明书【氨甲环酸片药品名称】通用名称:氨甲环酸片英文名称:Tranexamic Acid Tablets汉语拼音:AnjiahuansuanPian【氨甲环酸片成份】氨甲环酸片主要成份为:氨甲环酸。
化学名称:(e)-4-氨甲基环己烷甲酸。
分子式:C8H15NO2分子量:157.21【氨甲环酸片性状】氨甲环酸片为白色片。
【氨甲环酸片适应症】氨甲环酸片主要用于急性或慢性、局限性或全身性原发性纤维蛋白溶解亢进所致的各种出血。
弥散性血管内凝血所致的继发性高纤溶状态,在未肝素化前,慎用氨甲环酸片。
氨甲环酸片尚适用于:①前列腺、尿道、肺、脑、子宫、肾上腺、甲状腺、肝等富有纤溶酶原激活物脏器的外伤或手术出血;②用作组织型纤溶酶原激活物(-PA)、链激酶及尿激酶的拮抗物;③人工流产、胎盘早期剥落、死胎和羊水栓塞引起的纤溶性出血;④局部纤溶性增高的月经过多,眼前房出血及严重鼻出血;⑤用于防止或减轻因子VIII或因子IX缺乏的血友病患者拔牙或口腔手术后的出血;⑥中枢动脉瘤破裂所致的轻度出血,如蛛网膜下腔出血和颅内动脉瘤出血;应用氨甲环酸片止血优于其他抗纤溶药,但必须注意并发脑水肿或脑梗塞的危险性,至于重症有手术指征患者,氨甲环酸片仅可作辅助用药;⑦用于治疗遗传性血管神经性水肿.可减少其发作次数和严重度;⑧血友病患者发生活动性出血,可联合应用本药;⑨可治疗溶栓过量所致的严重出血。
【氨甲环酸片规格】0.25g。
【氨甲环酸片用法用量】口服:一次1~1.5g(4~6片),一日2~6g(8~24片)。
为防止手术前后出血,可参考上述剂量,为治疗原发性纤维蛋白溶解所致出血,剂量可酌情加大。
【氨甲环酸片不良反应】氨甲环酸片副作用较氨基己酸为少。
偶有药物过量所致颅内血栓形成和出血。
副作用尚有腹泻、恶心及呕吐;较少见的有经期不适(经期血液凝固所致)。
必须持续应用氨甲环酸片较久者,应作眼科检查监护(例如视力测验、视觉、视野和眼底)。
南方平差软件PA2005说明书

关于平差易(PA2005)平差易(Power Adjust 2005,简称PA2005),它是在Windows系统下用VC 开发的控制测量数据处理软件,也是南方测绘PA2002的升级产品。
它一改过去单一的表格输入,采用了Windows风格的数据输入技术和多种数据接口(南方系列产品接口、其他软件文件接口),同时辅以网图动态显示,实现了从数据采集、数据处理和成果打印的一体化。
成果输出丰富强大、多种多样,平差报告完整详细,报告内容也可根据用户需要自行定制,另有详细的精度统计和网形分析信息等。
其界面友好,功能强大,操作简便,是控制测量理想的数据处理工具。
如何安装平差易平差易可在Windows95、98、2000和XP下安装运行。
安装步骤平差易(PA2005)的安装光盘中有PA2005文件夹,打开此文件夹并找到setup.exe 文件,双击setup.exe后屏幕上将出现下图的界面。
平差易的安装准备等待2秒钟,平差易的安装准备完成后即进入平差易的安装。
点击“Next”进入软件安装“用户须知”界面如果同意安装许可,请点击“yes”。
安装路径在上图“安装路径”中设置PA2005的安装目录。
安装软件给出了默认的安装位置c:\Program Files\South Survey Office\Power Adjust,用户也可以通过单击Browse 按钮从弹出的对话框中修改软件的文件夹。
如果已选择好了文件夹,则可以单击Next 按钮开始进行安装。
此时平差易的主体程序已安装完毕。
安装完成后屏幕弹出以下界面,确定是否要安装软件狗的驱动程序。
驱动程序的安装点击“English”和“Chinese”可实现安装说明的英文与中文的切换。
如果要安装软件狗的驱动程序就点击“继续”,如果不安装就点击“退出”即可。
第一次安装此软件时必须安装软件狗。
软件狗驱动状态此界面中有当前计算机系统和软件狗驱动程序状态说明。
点击“继续”来替换以前的驱动程序。
肝素钠说明书

肝素钠注射液说明书请仔细阅读说明书并在医师指导下使用【药品名称】通用名称:肝素钠注射液英文名称:heparin sodium lnjection 汉语拼音:gansuna zhusheye 【成份】本品主要成份为肝素钠。
肝素钠系自猪或牛的肠黏膜中提取的硫酸氨基葡聚糖的钠盐,属黏多糖类物质。
辅料为:苯酚、注射用水。
【性状】本品为无色至淡黄色的澄明液体。
【适应症】用于防治血栓形成或栓塞性疾病(如心肌梗塞、血栓性静脉炎、肺栓塞等);各种原因引起的弥漫性血管内凝血(dic);也用于血液透析、体外循环、导管术、微血管手术等操作中及某些血液标本或器械的抗凝处理。
【规格】 2ml:12500单位【用法用量】(1)深部皮下注射:首次5000~10000单位,以后每8小时8000~10000单位或每12小时15000~20000单位;每24小时总量约30000~40000单位,一般均能达到满意的效果。
(2)静脉注射:首次5000~10000单位,之后,或按体重每4小时100单位/kg,用氯化钠注射液稀释后应用。
(3)静脉滴注:每日20000~40000单位,加至氯化钠注射液1000mi中持续滴注。
滴注前可先静脉注射5000单位作为初始剂量。
(4)预防性治疗:高危血栓形成病人,大多是用于腹部手术之后,以防止深部静脉血栓。
在外科手术前2小时先给5000单位肝素皮下注射,但麻醉方式应避免硬膜外麻醉,然后每隔8~12小时5000单位,共约7日。
【不良反应】毒性较低,主要不良反应是用药过多可致自发性出血,故每次注射前应测定凝血时间。
如注射后引起严重出血,可静注硫酸鱼精蛋白进行急救。
偶可引起过敏反应及血小板减少,常发生在用药初5~9天,故开始治疗1个月内应定期监测血小板计数。
偶见一次性脱发和腹泻。
尚可引起骨质疏松和自发性骨折。
肝功能不良者长期使用可引起抗凝血酶-iii耗竭而血栓形成倾向。
【禁忌】对肝素过敏、有自发出血倾向者、血液凝固迟缓者(如血友病、紫癜、血小板减少)、溃疡病、创伤、产后出血者及严重肝功能不全者禁用。
PA2005说明书

前言关于平差易(PA2005)平差易(Power Adjust 2005,简称PA2005),它是在Windows系统下用VC 开发的控制测量数据处理软件,也是南方测绘PA2002的升级产品。
它一改过去单一的表格输入,采用了Windows风格的数据输入技术和多种数据接口(南方系列产品接口、其他软件文件接口),同时辅以网图动态显示,实现了从数据采集、数据处理和成果打印的一体化。
成果输出丰富强大、多种多样,平差报告完整详细,报告内容也可根据用户需要自行定制,另有详细的精度统计和网形分析信息等。
其界面友好,功能强大,操作简便,是控制测量理想的数据处理工具。
开发商PA2005由南方测绘仪器公司开发,软件产品以及说明文档版权属广州南方测绘仪器公司,受著作权法保护,任何未经广州南方测绘仪器公司书面同意的修改、复制和反编译均属违法行为,由于非法使用本软件产生的后果,南方测绘仪器公司不承担任何法律责任,南方测绘仪器公司保留对软件产品的解释权限。
版权及注册商标AutoCAD、Arc/Info、MapInfo、MGE、Nikon、Leica、Geodimeter、Sokkia、Topcon、Pentax等分别为软件和相关公司的专用名称或注册商标,本手册仅为引用。
本公司相关产品作为政府信息产业部门认定的软件企业,南方测绘仪器公司一直致力于地理信息采集、成图及管理软件的开发与方案提供。
目前,公司的主要软件产品有:CASS是本公司开发的数字化地形地籍成图软件,该产品无论技术还是市场都已稳居国内同类产品的领先地位。
CLC为本公司开发的基于MapINFO平台的地籍信息管理专用软件,已在土地行业得到了广泛的应用。
CASSCAN为本公司的地图扫描矢量化专用软件,主要用于栅格地图的矢量化处理,是已有白纸地图进入GIS的必备软件,它与CASS、CLC及本软件都具有完美的数据接口。
SHIS for SM是本公司开发的房产信息系统(测绘版),主要用于房产图测绘、房产勘丈,房屋面积分摊、各种房产图件制作等工作,是房产测绘部门的首选软件。
PARAGON PA系列水力泵产品说明说明书

M /h L /s3ARAGON PUMP company was founded by a dedicated pump professional with over thirty (30)years of worldwide experience. The company’s goal is to provide high quality products at extremely competitive prices supported by the best customer service in the industry.To assure high quality, performance and reliability, PARAGON PUMPS are manufactured to international standards in facilities with ISO 9001 certification. PARAGON PUMP backs up itsH (m)H (m)H (ft)H (ft)Imp.g.p.m US.g.p.mImp.g.p.m US.g.p.mPARAGON PUMP COMPANY, LLC18102 Courtney Breeze Drive Tampa, Florida, 33647, USA Tel :(813) 994-3356Fax :(813) 994-1237PARAGON PUMP (ASIA) PTE LTD37 Kallang Pudding Road #08-08Tong Lee Building Block B Singapore 349315Tel :(65) 6841-2818Fax :(65) 6841-5988M /h L /s3PA SERIES2h1h3hb3n1sø2n1nBFDf ODPCDDN HOLES S DIA123876549All Iron Stainless Steel(AL)(SS)Cast Iron Stainless SteelCast Iron Stainless SteelCast Iron Stainless SteelCarbon Steel Stainless SteelStainless Steel Stainless SteelCast Iron Stainless Steel1.Bearing HousingRugged cast iron constructionwith four bearing housingcovering the complete range offorty nine pumps for maximuminterchargeability.2.Stuffing BoxStandard stuffing box includesgland packing and lantern ringwith internal flushing or singlemechanical seal with internal orexternal flush.3.ShaftOne piece stainless steel shaft infour sizes covering the completerange of forty nine pumps formaximum interchangeability.7.Shaft SleeveReplaceable fully machined, positivelydriven, hook type stainless steel shaftsleeve prevents damage to the shaftfrom gland packing or mechanical sealand reduces maintenance cost.8.Support FootRemovable and adjustable supportfoot provides added rigidity and easeof maintenance.9.BearingsAll pumps come with grease lubricatedball bearings as standard. Permanently,sealed greased bearings or oillubricated bearing also available.PA SERIES fully complies to both performanceand dimensional standards for the InternationalStandard DIN 242554.CasingThe cast iron volute casing isheavy duty design withintergrally cast feet, vertical topcentreline discharge and axialsuction nozzle with cast inletvane to improve flow into theimpeller and reduce requiredNPSH.5.ImpellerDouble shrouded type, hydraulicallybalanced and positive drive shaft keyand domed impeller lock nut.6.Wear RingsReplaceable wear rings are standardon all casings and on rear covers forlarger pumps which assures hydraulicperformance and reduces maintenancetime and cost.END ELEVATIONFLANGES DRILLEDTO ISO 2048 PN16SIDE ELEVATIONFLANGE DIMENSIONSNew 23082søw2m1mSUCTIONDISCHARGEa f xldi。
平差易2005讲解

4817.6050 4467.5243
9341.4820 8404.7624
B、 D 作为定 向点,它没有 设站,所以无 观测信息,但 在测站信息区 中必须输入它 们的坐标。
在测站信息区中输入A、B、C、D、2、3和4号测站点,其中A、 B、C、D为已知坐标点,其属性为10,其坐标如“原始数据 表”;2、3、4点为待测点,其属性为00,其它信息为空。如 果要考虑温度、气压对边长的影响,就需要在观测信息区中输 入每条边的实际温度、气压值,然后通过概算来进行改正。
以3号点为测站点,以2号点为定向点时,照准4号点的数据输入 如下图“测站3的观测信息”所示:
以4号点为测站点,以3号点为定向点时,照准C点的数据输入 如下图“测站4的观测信息”所示:
(3)数据法实例
2)水准实例 水准原始数据表
测站点 A 2 3 4 B 高差(米) -50.440 3.252 -0.908 40.218 距离(米) 1474.4440 1424.7170 1749.3220 1950.4120 高程 (米) 96.0620
二、主界面 主界面中包括测站信息区、观测信息区、图形显示区以 及顶部下拉菜单和工具条。
3 由观测数据到平差成果
一、用平差易做控制网平差的过程 第一步:控制网数据录入 第二步:坐标推算 第三步:坐标概算 第四步:选择计算方案 第五步:闭合差计算与检核 第六步:平差计算 第七步:平差报告的生成和输出
“闭合差”:表示该导线或导线网的观测 角度闭合差。 “权倒数”:即是导线测角的个数。 “限差”:其值为权倒数开方×限差倍数 ×单位权中误差(平面网为测角中误差)。 对导线网,闭合差信息区包括fx、fy、 fd、 K、最大边长, 平均边长以及角度闭合差 等信息。若为无定向导线则无fx、fy、fd、 K 等项。闭合导线中若边长或角度输入不 全也没有fx、fy、fd,、K等项。 在闭合差计算过程中“序号”前面“!” 表示该导线或网的闭合差超限,“” 表 示该导线或网的闭合差合格。“X”则表 注意:闭合导线中没有fx、 fy、fd、[s]、k和平均边长的 示该导线没有闭合差。 此实例数据的角度闭合差和高差闭合差都 原因为该闭合导线数据输入 中边长或角度输入不全(要 合格。 输入所有的边长和角度)。
海康威视摄像头系列产品说明书

*(50$1< ZZZRPHJDGH 'HFNHQSIURQQ *HUPDQ\
%(1(/8; ZZZRPHJDQO
More than 100,000 Products Available!
7HPSHUDWXUH
Calibrators, Connectors, General Test and Measurement Instruments, Handheld Instruments for Temperature Measurement, Ice Point References, Indicating Labels, Crayons, Cements and Lacquers, Infrared Temperature Measurement Instruments, Recorders, Relative Humidity Measurement Instruments, PT100 Probes, PT100 Elements, Temperature & Process Meters, Timers and Counters, Temperature and Process Controllers and Power Switching Devices, Thermistor Elements, Probes and Assemblies, Thermocouples, Thermowells and Head and Well Assemblies, Transmitters, Thermocouple Wire, RTD Probes
$465
logging on demand, and preset interval logging from 1 reading per minute to 1 reading per 24 hours.
Ford 产品型号说明书

DISCO DISCO
DI seo DI seo
DISCO DISCO DISCO DISCO DISCO DISCO
N/D DISCO
1U2Z2V001SA 1U2Z2V001SA
N/D 2U2Z2V001AL
8C2Z2001C 1U2Z2V001JA 2U2Z2V001 JA 2U2Z2V001JA 2U2Z2V001 JA 1U2Z2V001JA
E.O.
2
MOTORCRAFT®
BALATAS
APLICACIÓNPORMARCA
VEHÍCULO
CILINDROS
FORD
EDGE DISCO DEL. VENT. '18" Y TRAS. SOLI D. ESCAPE ESCAPE EcoBoost® 2WD ESCAPE EcoBoost® 4WD ESCAPE (D-D) ESCAPE (D-D) ESCAPE (D-D), CON HEV ESCAPE (D-D), SIN HEV ESCAPE (D-T) ESCAPE (D-T) ESCAPE (D-T) ESCAPE EUROPA ESCAPE S/HEV (D-T) ESCAPE S/HEV (D-T) ESCAPE S/HEV (D-T) ESCORT, GT ESCORT ESCORT ZX2 ESCORTZX2 EXCURSION EXLPLORER (D-D) EXLPLORER (D-D) EXPEDITION EXPEDITION EXPEDITION EXPEDITION EXPEDITION EXPEDITION EXPEDITION (D-D) EXPEDITION /MAX EXPEDITION/MAX EXPLORER EXPLORER EXPLORER EXPLORER EXPLORER EXPLORER EXPLORER (4DR) EXPLORER (4DR) EXPLORER SPORT EXPLORER SPORT EXPLORER, SPORT F/B-150 F/B-200 F-150 F-150 F-150 6L EFI
Powerful多媒体安装项目器说明书

Powerful multimedia installation projector equipped to take on the mostdemanding integration projectsRemote control(Included accessory)OptionsInstallation ProjectorPA621U / PA521U / PA671W / PA571W / PA721X / PA621XCable cover NP04CVOption lensNP11FL NP30ZL NP12ZL NP13ZL NP14ZL NP15ZLWireless LAN unitNP02LM1NP02LM2NP02LM3Replacement lampNP26LPCabinet dimensions *Stated projection distances are standard values.For a stack installation, the recommended projection distances will be different.*The values in the tables are design values and may vary.Throw distance and screen sizePA621U/PA521U (Aspect ratio 16:10)30"40"60"80"100"120"150"200"240"300"400"500"-0.71.01.41.72.12.6-----0.7 - 0.91.0 - 1.31.5 - 1.92.0 - 2.62.5 - 3.33.0 - 3.93.8 - 4.95.1 - 6.66.1 - 7.97.6 - 9.910.2 - 13.212.7 - 16.5--1.0 - 1.31.4 - 1.81.7 - 2.22.0 - 2.72.6 - 3.43.4 - 4.54.1 - 5.45.2 - 6.86.9 - 9.0 8.7 - 11.3-1.2 - 2.51.9 - 3.82.5 - 5.13.2 - 6.33.8 - 7.64.8 - 9.5 6.4 - 12.77.6 - 15.3 9.6 - 19.112.8 - 25.516.0 - 31.9--3.7 - 6.05.0 - 8.0 6.3 - 10.1 7.5 - 12.1 9.4 - 15.212.6 - 20.315.2 - 24.419.0 - 30.525.4 - 40.731.8 - 50.9--5.9 - 9.0 7.9 - 12.1 9.9 - 15.111.9 - 18.214.9 - 22.820.0 - 30.524.0 - 36.630.1 - 45.840.1 - 61.150.2 - 76.4PA721X/PA621X (Aspect ratio 4:3)30"40"60"80"100"120"150"200"240"300"400"500"(0.61x0.46m)(0.81x0.61m)(1.22x0.91m)(1.63x1.22m)(2.03x1.52m)(2.44x1.83m)(3.05x2.29m)(4.06x3.05m)(4.88x3.66m)(6.10x4.57m)(8.13x6.10m)(10.16x7.62m)-0.6 1.0 1.3 1.62.02.5-----0.7 - 0.90.9 - 1.21.4 - 1.91.9 - 2.52.4 - 3.22.9 -3.83.7 -4.84.9 - 6.45.9 - 7.77.4 - 9.6 9.8 - 12.812.3 - 16.0--1.0 - 1.31.3 - 1.71.6 - 2.12.0 - 2.62.5 - 3.23.3 - 4.34.0 - 5.25.0 - 6.56.7 - 8.7 8.4 - 10.9-1.2 - 2.41.8 - 3.72.4 - 4.93.0 - 6.13.7 - 7.44.6 - 9.2 6.1 - 12.3 7.4 - 14.8 9.2 - 18.512.3 - 24.715.4 - 30.8--3.6 - 5.84.8 - 7.86.0 - 9.7 7.3 - 11.7 9.1 - 14.712.2 - 19.614.7 - 23.618.4 - 29.524.6 - 39.430.7 - 49.2--5.7 - 8.7 7.6 - 11.6 9.6 - 14.611.5 - 17.614.4 - 22.019.3 - 29.423.2 - 35.329.1 - 44.238.8 - 59.048.6 - 73.8PA671W/PA571W (Aspect ratio 16:10)WUXGA typeXGA typeWXGA type30"40"60"80"100"120"150"200"240"300"400"500"(0.65x0.40m)(0.86x0.54m)(1.29x0.81m)(1.72x1.08m)(2.15x1.35m)(2.59x1.62m)(3.23x2.02m)(4.31x2.69m)(5.17x3.23m)(6.46x4.04m)(8.62x5.39m)(10.77x6.73m)(0.65x0.40m)(0.86x0.54m)(1.29x0.81m)(1.72x1.08m)(2.15x1.35m)(2.59x1.62m)(3.23x2.02m)(4.31x2.69m)(5.17x3.23m)(6.46x4.04m)(8.62x5.39m)(10.77x6.73m)-0.71.01.41.72.1 2.6-----0.7 - 1.01.0 - 1.31.5 - 2.02.0 - 2.62.5 - 3.33.0 - 4.03.8 - 5.05.1 - 6.66.1 - 8.0 7.7 - 10.010.2 - 13.312.8 - 16.7--1.0 - 1.31.4 - 1.81.7 - 2.22.0 - 2.72.6 - 3.43.4 - 4.54.1 - 5.45.2 - 6.86.9 - 9.0 8.7 - 11.3-1.2 - 2.5 1.9 - 3.8 2.5 - 5.1 3.2 - 6.4 3.9 - 7.7 4.8- 9.6 6.4 - 12.8 7.7 - 15.4 9.6 - 19.2 12.8 - 25.7 16.0 - 32.1-- 3.7 - 6.0 5.0 - 8.1 6.3 - 10.1 7.6 - 12.2 9.5 - 15.3 12.7 - 20.4 15.3 - 24.5 19.1 - 30.7 25.5 - 40.9 31.9 - 51.2NP13ZL NP14ZLNP15ZL--5.9 - 9.1 7.9 - 12.1 9.9 - 15.212.0 - 18.315.0 - 22.920.1 - 30.624.1 - 36.830.2 - 46.040.4 - 61.450.5 - 76.9· The projector can be unplugged during its cool down period after it is turned off.Parts of the projector will become heated during operation.Use caution when picking up the projector immediately after it has been operating.· Use caution when putting the projector in the soft case immediately after the projector has been operating. The projector cabinet is hot.Cat.No. WLPJ-1411-0013NMicrosoft is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.DisplayPort and DisplayPort Certified Logo are trademarks of the Video Electronics Standards Association, registered in the U.S. and other countries.CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of Crestron Electronics, Inc.Trademark PJLink is a trademark applied for trademark right in the United States of America and other countries.VESA is a trademark of a nonprofit organization, Video Electronics Standard Association.All other trademarks are the property of their respective owners.The images in this brochure are samples./ap/162359368142499Lens centreLens centreUnit: mmThree primary colour liquid crystal shutter projection1,024,000 (1,280 dots × 800 lines)Manual (zoom range depends on lens)Manual Manual40" to 500" (throw distance depends on lens)10-bit colour processing (approx. 1.07 billion colors)Built-in 10 W monaural speaker33 dB / 39 dBAnalog: 15 kHz, 24 to 100 kHz (24 kHz or greater for RGB inputs), conforms to VESA standards / Digital: 15 kHz, 24 to 153 kHz, conforms to VESA standards Analog: 48 Hz, 50 to 85 Hz, 100, 120 Hz conforms to VESA standards / Digital: 24, 25, 30, 48 Hz, 50 to 85 Hz, 100, 120 Hz conforms to VESA standardsAnalog: 1,920 × 1,200 (with Advanced AccuBlend) / Digital: 4,096 × 2,160 (with Advanced AccuBlend)Mini D-Sub 15-pin × 1, 5BNC x 1Stereo mini jack × 2Stereo mini jack × 1 (selected from Computer / BNC / HDMI)TypeA 19 pin(HDMI connector) with HDCP(V1.4) x 2YesTypeA 19 pin(HDMI connector) with HDCP(V1.4) x 1YesDisplayPort 20 pin connecter x 1Yes BNC × 1Stereo mini jack x 1 ,shared with 5BNC, BNC (CV), BNC (Y/C)BNC × 2Stereo mini jack x 1 ,shared with 5BNC, BNC (CV), BNC (Y/C)D-Sub 9-pin × 1USB type A × 1RJ-45 × 1, (Supports 10BASE-T/100BASE-TX)IEEE 802.11b/g/n (Optional)Stereo mini jack × 15 V / 10 mA, synchronized signal output for 3D useOperating temperature: 5 to 40°C (*5), Operating humidity: 20 to 80 % (with no condensation)Storage temperature: -10 to 50°C, Storage humidity: 20 to 80 % (with no condensation)Operating altitude: 0 to 3,650 m (1,700 to 3,650 m: Set [FAN MODE] to [HIGH ALUTITUDE])100-240 V AC, 50/60 Hz377 W (100-130 V) / 362 W (200-240 V)0.11 W (100-130 V) / 0.16 W (200-240 V)4.7 W (100-130 V) / 4.9 W (200-240 V)499 × 142 × 359 mm (Net dimensions not including protruding parts)591 × 259 × 491 mm (Gross dimensions)8.4 kg (not including lens) 11.2 kg (Gross weight)2,304,000 (1,920 dots × 1,200 lines)350 W AC 6,200 lm 6,000:1483 W (100-130 V)460 W (200-240 V)5.5 A-2.2 A330 W AC 5,200 lm 5,000:1463 W (100-130 V) 440 W (200-240 V)5.1 A-2.2 A350 W AC 6,700 lm 6,000:1483 W (100-130 V)460 W (200-240 V)5.5 A-2.2 A330 W AC 5,700 lm 5,000:1463 W (100-130 V) 440 W (200-240 V)5.1 A-2.2 A350 W AC 7,200 lm 6,000:1483 W (100-130 V)460 W (200-240 V)5.5 A-2.2 A330 W AC 6,200 lm 5,000:1463 W (100-130 V) 440 W (200-240 V)5.1 A-2.2 A0.79" (with MLA) × 3 (aspect ratio: 4:3)786,432 (1,024 dots × 768 lines)MethodSpecifications of main partsLight output (*3) (*4)Contrast ratio (*3) (all white/all black)Screen size(throw distance) Colour reproducibility Audio outputQuietness (ECO mode ON/ECO mode OFF)Scan rateMax. display resolution (horizontal × vertical)Input/output connectorsUsage environmentPower supplyPower consumptionRated input current Dimensions (W x H x D)WeightSize Pixels(*1) Zoom Focus Lens shiftingECO OFFHorizontal VerticalVideo input Audio input Audio outputVideo input Audio input Video output Audio output Video input Audio input Video input Audio input Video input Audio inputECO mode off ECO mode on STANDBY (NORMAL) STANDBY(Network STANDBY)Liquid crystal panel Projection lensesLamp wattage (*2)Computer/ComponentHDMI Input Terminals HDMI Output Terminal DisplayPort BNC (CV) BNC (Y/C)PC control connector USB port Ethernet port Wireless LAN (USB)Remote connector 3D SYNC output terminal 0.76" (with MLA) × 3 (aspect ratio: 16:10)*1 : Effective pixels are more than 99.99 %. *2 : 264W when ECO mode is on.*3 : This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT].The light output values will drop to 80 % when [ON] is selected for [ECO MODE]. If any other mode is selected as the [PRESET] mode, the light output value may drop slightly. *4 : Compliance with ISO21118-2005*5 : 35 to 40°C – “Forced ECO mode” (PA621U/PA521U will shift to the ECO-mode in stages starting from 33 °C.) • These specifications and the product’s design are subject to change without notice.Model name of the wireless LAN unit varies depending on the country where the unit is used (or to be used).NP02LM1 : NP02LM2 :NP02LM3 : United States, Canada, Mexico,Taiwan, Brazil, ColombiaEurope, United Arab Emirates,Saudi Arabia, Oman, South Africa, Turkey, Ukraine, Egypt,Israel, Australia,New Zealand,Japan, Thailand, China, Hong Kong, Singapore, South Korea,Sri Lanka, Pakistan, Vietnam,India, Indonesia, Philippines,Peru, Chile, Argentina, EcuadorRussiaTerminalsTilt-free and portrait mode supportThis 10 bit video processor represents an enormous leap in video processing, with true flagship performance in noise reduction,de-interlacing and scaling.Equipped with NEC 4,096 x 2,160 scaler NV1301 and the 3rd SweetVision TM circuitWide selection of inputs and outputsRemote control / monitoringECO modeLarge maintenance-free filterEnergy saving design with a standby power consumption of 0.16 W (200-240 V)This function seamlessly blends multipleprojected images to display a single high-resolution image.Built-in edge blendingMulti-display capabilities and Tiling technologies are integrated into the new PA series. This projector is also equipped with multiple digital input & HDMI output terminals that can connect multiple projectors in a digital daisy chain. These cutting-edge functions produce a beautiful high-resolution image, including a 4K/2K high-resolution display using 4 PA621U/521U projectors and various Picture in Picture/Picture by picture configurations.The projector uses large two-layer filters. Since they are highly effective at repelling dust, as long as the filter is replaced with new ones when changing the lamp, there is no need for regular cleaning.ECO mode that curbs electricity consumption and extends the lamp replacement time to a maximum of 4,000 hours.The projector is equipped with a wide range of input/output terminals and compatible with a variety of image sources, which lets you connect HDMI, DisplayPort, computer (analogue), 5-core BNC, video, and wired LAN (RJ-45)/wireless LAN* sources.Image Express Utility / Wireless Image Utility*Using Image Express Utility Lite contained on the supplied NEC Projector CD-ROM provides wired and wireless* data and audio transmission via peer-to-peer networking or over a network.Wireless Image Utility can send images directly from your iOS devices such as an Apple iPad, iPhone and iPod touch, which enables you to send the real-time images taken with its internal camera, web pages accessed or cloud files in combination with a file sharing application to the projector.Multiscreen functionThis feature allows the projectors to boost an image’s brightness up to 28,800 ANSI lm (PA721X), which is ideal for large screens and environments with strong ambient light. It also prevents the complete loss of an image, which can happen when using only one projector.Stacking capabilitiesGeometric correction*1 Value with XGA. *2 Brightness value when the lamp mode is set to "ECO OFF Mode" and the preset mode is "High-bright mode".*The lens shift mechanism does not work when using NP11FL.*As you maximise the tilt direction of the lens shift, the area surrounding t h e s c re e n m a y g e t d a r k e r a n d shadows may appear.Lens shifting range (with NP12ZL/NP13ZL/NP14ZL/NP15ZL)1V1H0.5 V(PA721X/PA621X/PA621U/521U)0.6 V(PA671W/PA571W)0.1V0.1H0.1HHeight of projected imageWidth of projected image0.3H*0.3H**The lenses are not included with this unit.HDBaseT models* are also available. *PA622U / PA522U / PA672W / PA572W / PA722X / PA622XLens specifications-0.8 : 140-1505,400 ANSI lm 4,600 ANSI lm 4,700 ANSI lm 4,000 ANSI lm 4,200 ANSI lm 3,500 ANSI lm 1.2 kg1.31.19-1.56 : 130-5005,600 ANSI lm 4,800 ANSI lm 5,000 ANSI lm 4,200 ANSI lm 4,600 ANSI lm 3,800 ANSI lm 1.2 kg1.30.81-1.06 : 152-5006,800 ANSI lm 5,900 ANSI lm 6,400 ANSI lm 5,400 ANSI lm 5,900 ANSI lm 4,900 ANSI lm 1.2 kg2.01.50-3.02 : 140-5007,200 ANSI lm 6,200 ANSI lm 6,700 ANSI lm 5,700 ANSI lm 6,200 ANSI lm 5,200 ANSI lm 0.84 kg1.62.97-4.79 : 160-5005,800 ANSI lm 5,000 ANSI lm 5,100 ANSI lm 4,300 ANSI lm 4,700 ANSI lm 4,000 ANSI lm 1.0 kg1.524.70-7.20 : 160-5005,600 ANSI lm 4,800 ANSI lm5,000 ANSI lm 4,200 ANSI lm 4,600 ANSI lm 3,800 ANSI lm1.0 kgManual (Focus only)Manual Fixed Short Throw Lens Zoom LensSix types of optional lenses available for flexible installationEnjoy greater installation flexibility with a complete line of optional bayonet style lenses (6) for quick and easy exchange. Lens throw distances range from 0.6 to 76.9 m.Lens shift function for easily adjusting the position of the projected imageThe projector is equipped with a lens shift that allows you to adjust the projected image horizontally or vertically. You can easily adjust the position of the projection just by turning the lens shift dials, without having to move the projector unit itself. Furthermore, the projector is also equipped with a centre lens design for easy alignment.4K Ultra HD support( 4,096 x 2,160 / 3,840 x 2,160 )12 bit gamma correction Advance colour correction(6-axis saturation and hue adjustment / skin tone) Video and film cadence detection (multi cadence)Seamless switching Active single 3D video supportRemote control ID Program timer with real time clock / OFF Timer Silent design of 33dB in ECO mode Built-in 10 W monaural speakerPIN security / Control panel lock / Security bar / Security slot Simple access pointNaViSet Administrator 2 AMX BEACONCRESTRON ROOMVIEW TM with emergency function PC Control Utility 4.0 for Windows PC Control Utility 5.0 for MACPJLink HTTP server Virtual remotePer-pixel motion adaptive de-interlacing Detail enhancementSuper resolution correction (3rd SweetVison TM )3D random, mosquito and block noise reductionPA571WPA621XPA521UPA671WPA721XPA621U6200ANSI lumens WUXGA 8.4kg6700ANSI lumens WXGA 8.4kg7200ANSI lumensXGA 8.4kg 5200ANSI lumens WUXGA 8.4kg5700ANSI lumens WXGA 8.4kg6200ANSI lumensXGA8.4kgLens shift dials* For the PA621U/PA521U, horizontal lens shift range is 0.15H at over 150"** These value are with the NP12ZL/NP13ZL/NP14ZL/NP15ZLBrightness using NP13ZL. Weight does not include lensThis feature corrects horizontal and vertical keystone distortion or adjusts the image when projecting onto an unique shaped screen.The projector can be rotated freely (360°) to point up or down depending on the installation requirements and can be installed on its side to create a portrait image.HDMI 1 INUSB PortEthernet(RJ-45)DisplayPort INCOMPUTER INAUDIO OUT (Stereo mini)PC CONTROL (D-Sub 9 pin)BNC AUDIO IN (Stereo mini)HDMI OUTHDMI 2 INBNC INCOMPUTER AUDIO IN (Stereo mini)3D SYNC (Mini DIN 4 pin)1920192019201200Daisy chain Daisy chain*Requires optional wireless LAN moduleREMOTE (Stereo mini)。
平易差PA2005说明书

平易差PA2005说明书产品介绍平易差PA2005是一款智能语音助手设备,便捷易用,为用户提供多项实用功能。
产品规格•尺寸:10cm x 10cm x 2.8cm•重量:150g•语音识别范围:5米内•电源:USB充电•电池容量:1500mAh•有效时间:8小时•其他:WiFi连接产品功能1.语音控制家居设备平易差PA2005可以控制各种智能家居设备,如智能插座、智能灯、智能开关等。
只需要简单的语音指令,即可完成操作。
2.智能购物用户可以通过平易差PA2005语音购物,支持所有大型电商平台。
用户只需告诉平易差需要购买的物品,平易差会自动打开对应的电商平台页面,并完成支付流程。
3.天气查询用户可以通过平易差PA2005查询当地和其他城市的天气情况。
用户只需说出所在城市或所要查询的城市名称,平易差就会为用户提供相关信息。
4.台词学习平易差PA2005可以记忆用户的喜好,学习各种电影、电视台词,并在以后的对话中加以运用,提高用户的娱乐体验。
5.提醒功能平易差PA2005还可以设置日程提醒,用户只需说出任务名称、时间和提醒内容,平易差就会在指定时间提醒用户。
产品使用方法•设备连接:将设备连接至电源,等待设备启动,设备启动完成后,设备进入待唤醒状态,等待用户唤醒。
•用户唤醒:将设备放置在用户易于操作的地方,用户只需要按下设备顶部按钮或拍打设备一下,即可唤醒设备。
•设备指令:用户可以直接通过语音指令操作设备,设备听取指令后给予相应的回复或执行相应的操作。
常见问题解答•Q: 设备唤醒失败怎么办? A: 请确认设备已连接电源,设备是否处于待唤醒状态,并且尝试重启设备。
•Q: 设备接收指令失败怎么办? A: 请确认设备当前是否稳定连接网络,是否连接正确的WiFi热点,并尝试重启设备。
注意事项•设备应置于离火源安全距离处,以免发生火灾。
•设备应定期清洁,以免灰尘影响设备功能。
•设备应避免敲击、摔落等行为,以免对设备造成损坏。
RECOM 电源 RACAC DC 转换器 PA-1 产品说明书

RAC AC/DC Conver er4 Watt Single OutputRAC04-K/277IEC60950-1 certified IEC62368-1certified UL62368-1 certifiedCSA/CAN C22.2 No. 62368-1-14 certified EN62368-1 compliant EN60335-1 compliant EN61010-1 compliant IEC/EN61558-1 compliant IEC/EN61558-2-16 compliant EN55032 compliant EN55024 compliantEN55014-1 /-2 compliant IEC/EN61204-3 compliant FCC 47 Part 15CB ReportSelection GuidePart Input Output Output Efficiency Max. CapacitiveNumber Voltage Range Voltage Current (1) typ. (2)Load [(VAC] [VDC] [mA] [%] [µF)RAC04-05SK/277 80-305 5 800 76 7200RAC04-12SK/277 80-305 12 333 78 1000RAC04-15SK/277 80-305 15 267 80 820RAC04-24SK/277 80-305 24 167 80 220On RequestRAC04-3.3SK/277 80-305 3.3 1200 73 10000Notes:Note1: Refer to “Line Derating“ graphNote2: Measured @ 230VAC/50Hz at +25°C with constant resistant mode at full loadDescriptionThe RAC04-K/277 series delivers an uncompromising 4 watts of continuous output power (6W peak) in harsh industrial and household environments. These modules deliver full load output power from -40°C to 75°C across the entire input range of 80VAC to 305VAC and are certified for operation with power derating up to 90°C air ambient. A peak load capability of up to 150% supports dynamic power demands of applications. This series of fully encapsulated AC/DC modules is a complete solution without the need for external components which supports Ecodesign Lot 6 standby mode operation for worldwide applications in automation, industry 4.0, IoT, household, and home automation. With international safety and EMC certifications for industrial, domestic, ITE, and household applications, these are some of the most versatile power modules on the market. Due to their reinforced class II installation rating for floating outputs and their significantly wide margin to class B emissions compliance without external components and a certified 4kV AC (5.25 kV DC) isolation, these are the easiest to use modular power solutions in the industry.nom. Output Power nom. Output VoltageRAC04-__ SK/277Model NumberingS ingleE224736Ordering Examples RAC04-05SK/277 = 5Vout Single RAC04-12SK/277 =12VoutSingleSpecifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)REGULATIONSParameterCondition ValueOutput Accuracy ±1.0% typ.Line Regulation ±0.5% typ.Load Regulation 1.0% typ.Transient Response25% load step changerecovery time4.0% max.500µs10.5-0.5-1D e v i a t i o n [%]0102030405060708090100Output Load [%]10.50-0.5-1D e v i a t i o n [%]0102030405060708090100Output Load [%]RAC04-05SK/277RAC04-12SK/277Deviation vs. Load(80-305VAC)Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)10.5-0.5-1D e v i a t i o n [%]0102030405060708090100Output Load [%]10.50-0.5-1D e v i a t i o n [%]0102030405060708090100Output Load [%]RAC04-15SK/277RAC04-24SK/277Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)SAFETY AND CERTIFICATIONSCertificate Type Report / File Number StandardAudio/video, information and communication technology equipment - Safety requirements E224736UL62368-1:2014, 2nd Edition CAN/CSA C22.2 No. 62368-1-14, 2nd EditionInformation Technology Equipment, General Requirements for Safety (CB)E491408-A6-CB-1IEC60950-1:2005 + A2:2013, 2nd EditionInformation Technology Equipment, General Requirements for Safety EN60950-1:2006 + A2:2013 Audio/video, information and communication technology equipment - Safety requirements (CB)E491408-A6011-CB-1IEC62368-1:2014, 2nd Edition Audio/video, information and communication technology equipment - Safety requirements (LVD)EN62368-1:2014 + A11:2017 Household and similar electrical appliances - Safety - Part 1: General requirements (LVD)EN60335-1:2012 + A1:2018Safety of power transformers, power supplies, reactors and similar products for supply voltages up to 1100 V IEC61558-1:2005 2nd Edition + A1:2009EN61558-1:2005 + A1:2009Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)Certificate Type Report / File Number StandardSafety of transformers, reactors, power supply units and similar products for supply voltages up to 1100 V - Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units (LVD)IEC61558-2-16:2009 + A1:2013, 1st EditionEN61558-2-16:2009 + A1:2013Safety requirements for electrical equipment for measurement, control and laboratory use -Part 1: General requirements (LVD)EN61010-1:2010 RoHS2RoHs-2011/65/EU + AM-2015/863 EMC Compliance (Household)Report / File Number Standard / Criterion Electromagnetic compatibility - Requirements for household appliances, electric tools and similarapparatus - Part 1: Emission (8)EN55014-1:2006 + A2:2011 Electromagnetic compatibility - Requirements for household appliances, electric tools and similarapparatus - Part 2: ImmunityEN55014-2:2015 ESD Electrostatic discharge immunity test Air ±8kV; Contact ±4kV IEC61000-4-2:2008, Criteria B Fast Transient and Burst Immunity AC Power Port: ±1.0kV IEC61000-4-4:2012, Criteria B Surge Immunity AC Power Port: L-N ±1.0kV IEC61000-4-5:2014, Criteria B Immunity to conducted disturbances, induced by radio-frequency fields AC Power Port: 3V EN61000-4-6:2013, Criteria AVoltage Dips and Interruptions Voltage Dips: 100%60%EN61000-4-11:2004, Criteria CEN61000-4-11:2004, Criteria CEMC Compliance (Multimedia)Condition Standard / Criterion Low voltage power supplies, d.c. output - Part 3: Electromagnetic compatibility IEC/EN61204-3:2000, Class B Electromagnetic compatibility of multimedia equipment - Emission requirements (9)EN55032:2015, Class B Information technology equipment - Immunity characteristics - Limits and methods of measurement EN55024:2010 + A1:2015 ESD Electrostatic discharge immunity test Air ±2,4,8kV; Contact ±4kV IEC61000-4-2:2008, Criteria BRadiated, radio-frequency, electromagnetic field immunity test10V/m (80 - 1000MHz)IEC61000-4-3, Criteria A 3V/m (1800MHz, 2600Mhz,3500MHz, 5000MHz)IEC61000-4-3:2006 + A2:2010, Criteria AFast Transient and Burst Immunity AC Power Port: ±2.0kV IEC61000-4-4, Criteria B AC Power Port: ±1.0kV IEC61000-4-4:2012, Criteria ASurge Immunity AC Power Port: L-N ±1.0kV IEC61000-4-5:2014, Criteria A Immunity to conducted disturbances, induced by radio-frequency fields AC Power Port: 10V IEC61000-4-6, Criteria AVoltage Dips and Interruptions Voltage Dips:100% / 30%70%40%IEC61000-4-11:2004, Criteria AIEC61000-4-11:2004, Criteria BIEC61000-4-11:2004, Criteria C Interruptions: >95%IEC61000-4-11:2004, Criteria ALimits of Voltage Fluctuations & Flicker EN61000-3-3:2013 Limitations on the amount of electromagnetic interference allowed from digital and electronicdevicesFCC 47 Part 15 Subpart B:2017, Class B Notes:Note9: If output is connected to GND, please contact RECOM tech support for further informationDIMENSION and PHYSICAL CHARACTERISTICSParameter Type ValueMaterial case/baseplatepottingPCBplastic, (UL94 V-0)silicone, (UL94 V-0)FR4, (UL94 V-0)Dimension (LxWxH)36.7 x 27.2 x 17.4mm Weight30g typ.Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)PACKAGING INFORMATIONParameter Type Value Packaging Dimension (LxWxH)tube506.4 x 29.8 x 25.5mm Packaging Quantity12pcs Storage Temperature Range-40°C to +85°C Storage Humidity non-condensing20% to 90% RH max.The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause。
丙烯酸酯结构胶安全资料手册说明书

修改日期: 14/04/2015安全资料手册编号 10267修改的内容 1安全资料手册的性质丙烯酸酯结构胶按照GB/T 16483-2008、GB/T 17519-2013编制产品标识产品名称丙烯酸酯结构胶产品编号IT101B化学品的推荐用途和限制用途推荐的用途粘合剂限制的用途针对具体用途的建议未确定。
化学品安全技术说明书提供者的详细信息供应商依工聚合工业(吴江)有限公司江苏省吴江市经济技术开发区庞金北路4680号电子邮件:********************联系人依工聚合工业(吴江)有限公司应急电话物质或混合物的分类标号与 GHS一致物理化学危害性没有分类。
人类健康方面 2 眼刺激 - H319;1 敏化皮肤 - H317;1B 生殖毒性 - H360Df环境方面 2 危害水生环境-慢性危险 - H411健康危害具有刺激性。
可能会引起皮肤敏感。
环境含有危害环境的物质。
理化危害有机过氧化物, 受热后会发生剧烈分解反应。
分解的产物容易燃烧。
标签要素符合(EC) No. 1272/2008的标签警示词危险危险性说明H317可能导致皮肤过敏反应。
H319造成严重眼刺激。
H360Df 可能对胎儿或生育能力造成伤害。
H411对水生生物有毒并具有长期持续影响。
防范说明P201在使用前获取特别指示。
P273防止排放到环境。
P280穿戴防护手套/防护服/护眼装备/面部防护装备。
P281使用所需的个人防护装备。
P305+351+338如进入眼睛:用水小心冲洗几分钟。
如戴隐形眼镜并可方便地取出, 取出隐形眼镜。
继续冲洗。
P308+313如接触到或有疑虑:求医 /就诊。
P313求医/就诊。
P501将内容物/容器弃置到 ……补充的防范说明P202在读懂所有安全防范措施之前切勿操作。
P272受沾染的工作服不得带出工作场地。
P261避免吸入蒸汽/喷雾。
P264处理后请彻底清洗受沾染的皮肤。
P321特定治疗(见本标签上的医学建议)。
PA2005说明

一、主界面启动后即可进入平差易的主界面。
PA2005的操作界面主要分为两部分——顶部下拉菜单和工具条,如下图“PA2005主界面”所示:PA2005主界面主界面中包括测站信息区、观测信息区、图形显示区以及顶部下拉菜单和工具条。
二、用平差易做控制网平差的过程第一步:控制网数据录入第二步:坐标推算第三步:坐标概算(一般情况不概算,省略即可) 第四步:选择计算方案第五步:闭合差计算与检核 第六步:平差计算第七步:平差报告的生成和输出测站信息区观测信息区图形 显示 区顶部下拉菜单工具条作业流程图:控制网数据的录入一般按照(控制网录入说明,见下面控制网录入说明章节)进行手输,输入完成后点“坐标推算”菜单,在测站信息区可以看到每个待定点(属性00)的推算近似坐标/高程,然后点选择“计算方案”菜单(点击该菜单后弹出对话框,里面需要选择本次控制的等级、平面控制网还是高程控制网、单位权先验中误差、限差要求等(其中如果你做的是导线就选择平面控制网,如果是水准或三角高程就选择高程控制;对于导线网单位权先验中误差根据你所使用的全站仪来定,譬如说你全站仪施2+3的,那么固定误差就是2,比例误差系数就是3;控制网等级和限差要求就是你这次所做控制网的等级是什么等级就选择什么等级,限差是根据所选控制网等级自动生成的,所以限差一般不用输入))。
然后点击闭合差计算和检核菜单(如果闭合差超限会出现红色的感叹号,超限后一定要检查录入的数据是不是有问题,如果没问题需要检查原始数据的正确性,原始数据没问题就需要对超限的地方进行重测),当限差合格后点击平差菜单就基本完成平差程序了。
控制网数据的录入说明控制网的数据录入分数据文件读入和直接键入两种。
凡符合PA2005文件格式(格式内容详见附录A)的数据均可直接读入。
读入后PA2005自动推算坐标和绘制网图。
PA2005为手工数据键入提供了一个电子表格, 以“测站”为基本单元进行操作, 键入过程中PA2005将自动推算其近似坐标和绘制网图。
Belimo ZTH AP 电子调节阀说明书

ZTH APTechnical dataElectrical dataNominal voltage AC 24 V, 50/60 Hz, DC 24 V (from actuator)Operating rangeAC 19.2...28.8 V / DC 21.6...28.8 V Power consumption Operation 1 WConnection Socket for connecting cable ZK1-GEN (3 m) supplied with connectorInterface USB 2.0USB socket type B, connecting cable (1 m) with socket A to B supplied Optional cablesZK2-GEN, ZK6-GENInterfaceCommunication Point to Point (PP), no bus mode possible (MP)Operating modesParameterisationPoint to Point (PP)Connection using service socket or connecting terminals on the actuatorMP level converter (ZIP function)Connection in control cabinet or via service socket on actuatorFor MP monitor operation, connection on MP-Bus OperationLCD display 2 x 16 characters, with background lighting Keysi / esc / ▲ / ▼ / OKSafetyProtection class III Safety extra-low voltage EMCCE according to 2004/108/EU Operating temperature 0...50 °C, non-condensing Non-operating temperature –20...50 °C, non-condensing Dimensions / weightDimensions L x W x D: 95 x 55 x 25 mm WeightApprox. 135 gService tool for parameterisable andcommunicative actuators / VAV controllers and HVAC performance devices from Belimo.•Connection via service socket on the device or MP/PP connection •ZIP USB functionSafety notes!•The device must not be used outside the specified field of application, especially not in aircraft or in any other airborne means of transport.•Only connection to Belimo devices with 24 V safety extra-low voltage and PP/MP interface permitted.•Changes to parameters etc. may only be performed following consultation with/specification from the OEM, device or mechanical/electrical contractor. Operating and adjustment regulations must be observed.Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoValve product range..-MF / ..-MP / ..-MPL / ..-MFT(2) /..-MOD / ..LONEPIV - pressure-independent characterisedP6..W..-MP available since 2011control valveFire damper actuator BF-TopLine with BKN230-24MPVAV product range VRD2 / VRD2-L available 1992-2007VRD3available since 2008VRP-M (VAV and STP applications)available since 2005NMV-D2..available 1992-2000LMV-D2M / NMV-D2M..available 2000-2006LMV-D2-MP / NMV-D2-MP / SMV-D2-MP.., LHV-D2-MP..available 2006-2011LMV-D2LON / NMV-D2LON available 2006- 2011LMV-D3-MP / NMV-D3-MP / SMV-D3-MP.., LHV-D3-MP..available since 2011LMV-D3LON / NMV-D3LON available since 2011LMV-D3-MOD / NMV-D3-MOD available since 2012 HVAC final controlling elements According to system description (e.g. Energy Valve)sharedlogic According to system descriptionConnectionConnection and supply The ZTH AP is supplied via the actuator. The connection is set up•either directly on the service socket of the actuator•or via PP/MP connection (U5), e.g. connection socket, control cabinet and room controllerCR24.Type of connection and connection cable Suitable cableZK1-GENZK2-GENZK4-GENZK6-GENService tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoDirect connection to the MP-Bus or MP master is not possible with the ZTH AP .RightWrongConnection via service socket - local connection with ZK1-GEN cableBelimo PC-ToolZK1-GENUSB 2.02124VGNDi esc okUSBMPBELIMOConnection via connecting cable - local connection with ZK2-GEN cableAC 24 V ~T_Connection in the MP-Bus systemNoteThe USB driver required will be automatically installed with PC-Tool version 3.9 or higher. For older versions of the PC-Tool, the driver can be downloaded from and installed separately.ZIP function connectionService tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoZIP function connectionPC-Tool as MP master•Actuator parameterisation via MP-Bus•Specification of setpoints for simulation of actuators via MP-Bus •Reading in of sensors that are connected to the MP actuator •Recording of graphic trendsPC-Tool connection with ZK6-GEN, ZK4-GEN on Belimo gateways•For connection to UK24MOD and UK24BAC, use the ZK6-GEN cable.•For connection to UK24EIB and UK24LON, use the ZK4-GEN cable.Note Interrupt connection between ZTH AP and MP master before using the ZIP function.*Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoConnection with ZIP functionPC-Tool as monitorCheck the MP communication with the MP monitor tool (module of PC-Tool V3.x).PC-Tool with monitor function / connection: ZK2-GEN to MP masterPC-Tool with monitor function / connection: tool socket with ZK6-GEN, ZK4-GENMP-MasterService tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoOperationWhen the ZTH AP is connected to the Belimo actuator, the operating device starts and data isread from the connected device. The available adjustment and operating options are displayedin accordance with the device type. The available setting parameters are listed in the productdocumentation for the actuators. See Operating elements LCD display- Background lighting- Display with 2 x 16 charactersKey function▼ and ▲Forward /backwardChange value / statusOK Confirm entry,go to submenuESC Abort entry,leave submenu,discard changei Shows additional information(if available)- RJ12 connection socket- USB connection socket for communication with PCLanguage setting, unit depiction Language and units can be set in the Configuration menu.Operation Operating is context-related, i.e. the user sees only the options available for the connecteddevice. The corresponding Configuration table is read from the actuator for this purpose.In addition to the parameter type, this table also contains the corresponding divisions, e.g.:minimum running time which can be set, type etc. Non-relevant options are not displayed.Menu structure, handlingStarting / endingunplugging it.Device specifications/Technical data For a more detailed description, including setting parameters, please refer to the respectiveseparate product information. See ¦ Documentation.Starting configuration 1. Press the key (OK) while simultaneously plugging in the connecting cable.2.Configuration menu display appears.Configuration menu Option / Display Setting ProductrangeExplanationEmpty cache Yes / No Function to delete data profiles ofHVAC performance devices fromthe local cacheBacklight After 0..255 sec off /always active Setting for duration of backlight in secondsShow favourites Disabled/ after1…65535 s HVACperformancedevices(EnergyValve)Alternating display of the first 3values after the set timeOEM number0…65535VAVAdvanced Mode 1)Yes / No VAVFireprotectionModbus Enabled settings:–VAV: direction of rotation–VAV: set Vmin / Vmax to original values (call up OEM setting)–BF-Top: adaption–Modbus: basic addressExpert Mode 1)Yes / No VAVValves Enabled settings:–VAV: switching mode–VAV: V‘mid parameter–VAV: altitude compensationPICCV function Yes / No Valves Belimo US:Enable PICCV Wizard function Power supplymeasurementValue V (AC)Pressure unit Pa / in WC VAVFlow unit (water)m3/h / l/min / gpm ValvesFlow unit (air)m3/h / l/s / cfm VAVExit configuration ESC1) Only activate this option as needed and with the respective know-how. Adjustment of the respective parameters requires special expertise.MP addressModbus actuatorsModbus-specific communication settings of an actuator with integrated Modbus interface (..-MOD).Device identificationThe following menu tree shows the basic functions which are identical for all devices.Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoFunctions for damper / rotary valve product rangeMenu tree The ZTH AP recognises the device family of the connected device automatically. The menu andthe options available are shown related to the connected device.Adjustment/display optionsLM24A-MP.Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoFunctions for globe valve product rangeMenu treeThe ZTH AP recognises the device family of the connected device automatically.The menu and the options available are shown related to the connected device.Adjustment/display optionsNVK24A-MP-TPC.Functions for EPIV - pressure-independent characterised control valveMenu treeAdjustment/display optionsEPIV.Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoFunctions for VAV product rangeMenu treeThe following menu tree corresponds to the new VAV-Compact D3 generation: L/N/SMV-D3-MP, LHV-D3-MP, L/ NMV-D3LON , L/MNV-D3-MOD 1)1)For Modbus settings, see previous description of "Basic functions for Modbus actuators"Adjustment/display optionsLMV-D3-MP.DeviationsVRD2 (1992-2007)Display showing actual value/setpoint in [% Vnom]Vmin in [% Vmax], Vmax in [% Vnom]Read only PP VRD3 (as of 2008)Display showing actual value/setpoint in [% Vnom]Vmin in [% Vnom], Vmax in [% Vnom] HW potentiometer setting «Tool →Read/write, otherwise → Read onlyPPVRP-M VAV Up to V2.16 Vmin in [% Vmax], Vmax in [% Vnom]As of V3.0 Vmin in [% Vnom], Vmax in [% Vnom]PP / MP1…8NMV-D2 (1992 – 2000)NMV-D2M (2000 –2006)Display showing actual value/setpoint in [% Vnom], Vmin in [% Vmax], Vmax in [% Vnom]PPPP / MP1 (8)Altitude compensation This function requires VAV-Compact D3 withfirmware V2.06 (03/2013) or higher and ZTH with firmware V2.01 or higher.Note: VAV-Universal actuatorsThe V-actuators L/N/SM24A-V, L/NMQ24A-SRV-ST, which fit the VAV universal controllers VR.., have a tool connection but are nevertheless not tool-capable.Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoFunctions for BF-TopLine fire damper actuatorsMenu treeAdjustment/display options BF-TopLine actuator.Functions for MPL actuatorsMenu treeAdjustment/display optionsMPL actuator.Range 0...100%(OPEN/CLOSE/Stop)Functions for room sensors MS24A-R0x-MPXMenu treeAdjustment/display optionsRoom sensor MS24A-R08-MPX(T, rH, CO2, VOC).Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoZIP functionsIn this configuration, the ZTH AP works as a level converter between the USB port of a PC and the Belimo MP device. The correct driver will be automatically installed on the PC when the ZTH AP is plugged in. As soon as the USB interface is connected, the ZTH AP switches to ZIP mode.Power supplyChecking the power supplyThe ZTH AP allows the "AC 24 V" power supply (III safety extra-low voltage) of the Belimo devices to be checked. Voltages >30V are not permitted!Application: e.g. commissioning, troubleshooting in the event of a malfunction.Measuring processEquipment: ZTH AP , ZK2-GEN Connect in the following order:•Connect free wires of the ZK2-GEN to AC 24 V.•White to GND (connection 1 actuator/VAV controller)•Blue to ~ (connection 2 actuator/VAV controller)•Do not connect third wire (turquoise)Start:Press the ZTH AP key (OK) while at the same time connecting the RJ12 plugSelect "AC measurement" function with arrow key (▼)End:"Supply okay" display: AC supply in the range 19.2 ... 28.8 VAC value: measured AC voltage (accuracy ±1.0 V provided that VHW >95%)Explanation of VHWThe VHW unit describes the relationship between the positive and negative half-wave.The deviation between the positive and negative half-wave value must not be too great. The following formula applies: positive HW / negative HW x 100 should be >80%:Possible problemsThe following factors influence the half-wave load:•Transformer dimensions too small•Maximum signal cable length between transformer and actuator exceededpositive HWnegative HWNoteIf the ZTH AP is connected to the PC, the display flashes a few times until the driver is installed on the PC.NoteOnly connect RJ12 plug to ZTH AP when starting!Connection as MP master (e.g. PC-Tool).If there is bus communication, this is indicated by Tx and Rx flashing.Connection for monitor function with PC-Tool.If there is bus communication, this is indicated by Tx and Rx flashing.Service tool for parameterisable and communicative actuatorsVAV controllers and HVAC performance devices from BelimoFirmware upgradeThe ZTH AP can be updated to the latest firmware version using the ZTH AP updater. The required software and the instructions for the upgrade can be downloaded from the download area of the Belimo website .CompatibilitiesFunction and handlingThe ZTH AP includes the complete functionality of all previous versions of the ZTH-GEN and ZTH-VAV.The hardware of the ZTH AP is not however compatible with the hardware of the ZTH-GEN. The updates for the ZTH-GEN cannot be loaded to the ZTH AP .In addition, the new ZTH AP supports the ZIP USB function. This can be used for the ZTH AP updates and also as a level converter USB/MP with the PC-Tool.ZEV The ZEV adjustment tool (1992 to 2007) is replaced by the ZTH AP . ZTH-VAVIs replaced by the ZTH AP .ZTH-GEN V2.xx / V3.xx / V4.xxIs replaced by the ZTH AP .NoteLatest information about firmware upgrades, version overviews, documentation:See Version overviewV 2.03V 2.02•Device identification for VRD2 / NMV-D2 corrected•New menu "Sensor monitoring of air bubbles" for the EPIV •Error correction: impairment of the sensor measurement at Y3•Error correction: impairment of the analogue setpoint at Y3V 2.01• Release of the ZTH and ZIP function。
baso2005-1说明书

baso2005-1说明书
1、操作前后的检查:
(1)检查内部有无杂质或水滴,并清除杂质及水滴。
(2)检查转盘是否松动,如果松动请锁紧后再使用。
(3)检查门盖是否可盖紧,并检查螺丝是否松动,如不正常,应暂停使用并通知当地经销商。
(4)检查接地线是否正确连接。
(5)检查灯信号及开关是否运作正常。
2、每日应检查项目:
清理机内的污迹,检查转盘是否有刮伤,变形或腐蚀,如有上述情形请联络当地经销商作进一步检查。
3、每年应检查之项目:
检查转盘固定螺帽是否松动,若发现转速表的数值无法符合实际转速,请联络当地经销商检查。
4、清洗:
当样品弄脏转盘时,操作人员请戴好橡胶手套,用少量清洁剂擦拭,并用干布擦干。
消毒转盘时,温度不要超过100℃(不得长时间加温),严禁使用蒸汽消毒。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
前言关于平差易(PA2002)平差易(Power Adjust 2002,简称PA2002)是在Windows系统下用VC 开发的控制测量数据处理软件,也是南方测绘Adjust(南方平差大全)软件的升级产品。
它一改过去单一的表格输入,采用了Windows风格的数据输入技术和多种数据接口(南方系列产品接口、其他软件文件接口),同时辅以网图动态显示,实现了从数据采集、数据处理和成果打印的一体化。
成果输出丰富强大、多种多样,平差报告完整详细,报告内容也可根据用户需要自行定制,另有详细的精度统计和网形分析信息等。
其界面友好,功能强大,操作简便,是控制测量理想的数据处理工具。
开发商PA2002由南方测绘仪器公司开发,软件产品以及说明文档版权属广州南方测绘仪器公司,受著作权法保护,任何未经广州南方测绘仪器公司书面同意的修改、复制和反编译均属违法行为,由于非法使用本软件产生的后果,南方测绘仪器公司不承担任何法律责任,南方测绘仪器公司保留对软件产品的解释权限。
版权及注册商标AutoCAD、Arc/Info、MapInfo、MGE、Nikon、Leica、Geodimeter、Sokkia、Topcon、Pentax等分别为软件和相关公司的专用名称或注册商标,本手册仅为引用。
本公司相关产品作为政府信息产业部门认定的软件企业,南方测绘仪器公司一直致力于地理信息采集、成图及管理软件的开发与方案提供。
目前,公司的主要软件产品有:CASS是本公司开发的数字化地形地籍成图软件,该产品无论技术还是市场都已稳居国内同类产品的领先地位。
CLC为本公司开发的基于MapINFO平台的地籍信息管理专用软件,已在土地行业得到了广泛的应用。
CASScan为本公司的地图扫描矢量化专用软件,主要用于栅格地图的矢量化处理,是已有白纸地图进入GIS的必备软件,它与CASS、CLC及本软件都具有完美的数据接口。
SHIS for SM是本公司开发的房产信息系统(测绘版),主要用于房产图测绘、房产勘丈,房屋面积分摊、各种房产图件制作等工作,是房产测绘部门的首选软件。
“测图精灵”(MG 2001)、“工程精灵”(EG 2002)是南方测绘仪器公司开发的“测绘通”系统产品,分别用于数字测图与工程测量的外业数据采集与处理。
与本软件平行,本公司将在近期发布“控制精灵”(CG 2002)。
它是一个基于掌上机的控制测量外业的采集与记录工具,它所的数据可以直接导入本软件中,从而实现控制测量内、外业的一体化。
本公司还提供房产、土地等行业信息系统的构建与开发方案。
南方测绘仪器公司对以上产品及命名享有版权。
技术服务用户在购买PA2002 for S&M 2.0正版并成为注册用户之日起,将长期享受南方测绘仪器公司的技术服务及升级政策。
用户应及时填写和回寄软件包装盒中的“用户注册卡”,以便成为PA2002 for S&M 2.0的注册用户。
您可以通过下述方式的任何一种享受南方公司快捷的技术服务:热线电话:(020)85582265-24/25,85599960传真:85584343, PA2002负责人:夏玉平、魏家才通讯地址:广州市黄埔大道西107号,邮政编码510620。
电子邮件:softspt@公司网站()设有“软件园地”,用户可以在该园地中获得快捷的技术支持,并可参与用户、开发人员、技术服务人员之间的讨论与交流。
用户还可以在该园地内了解到南方软件的最新动态、下载有关产品的最新版本及相关技术资料。
对于本软件,用户除了享受分公司的培训和技术支持外,广州总部还将设立一个网上服务中心来解决PA2002应用中出现的技术问题和数据计算问题,并且这些问题将在一个星期内得以回复。
您还可以与当地分公司联系,南方公司各地的分公司都具有软件技术服务能力。
谢谢您的选择,我们的目标是让您的选择成为您的自豪。
如何安装平差易平差易可在Windows95、98、2000和XP下安装运行。
安装步骤如下:平差易(PA2002)的安装光盘中有PA2002文件夹,打开此文件夹并找到setup.exe 文件,双击setup.exe后屏幕上将出现下图的界面。
平差易的安装准备等待2秒钟,平差易的安装准备完成后即进入平差易的安装。
平差易的安装点击“Next”进入软件安装“用户须知”界面用户须知如果同意安装许可,请点击“yes”。
安装路径在上图“安装路径”中设置PA2002的安装目录。
安装软件给出了默认的安装位置c:\Program Files\South Survey Office\Power Adjust,用户也可以通过单击Browse 按钮从弹出的对话框中修改软件的文件夹。
如果已选择好了文件夹,则可以单击Next 按钮开始进行安装。
此时平差易的主体程序已安装完毕。
安装完成后屏幕弹出以下界面,确定是否要安装软件狗的驱动程序。
驱动程序的安装点击“English”和“Chinese”可实现安装说明的英文与中文的切换。
如果要安装软件狗的驱动程序就点击“继续”,如果不安装就点击“退出”即可。
第一次安装此软件时必须安装软件狗。
软件狗驱动状态此界面中有当前计算机系统和软件狗驱动程序状态说明。
点击“继续”来替换以前的驱动程序。
在安装过程中有以下提示:系统提示为“是否安装支持16位驱动”,如点击“是”则此软件可在Windows95、98、2000和XP下安装和运行,如点击“否”则此软件只能在Windows95、98下运行,否则它将无法读到软件狗。
点击“是”,继续软件狗驱动程序的安装。
驱动程序安装完成点击“完成”结束驱动程序的安装。
浏览平差易启动平差易启动方式有三种:第一种:直接在桌面上双击平差易的图标。
第二种:点击“开始\程序\South Survey Office\南方平差易2002”。
第三种:点击“C:\Program Files\South Survey Office\Power Adjust\PA.exe”主界面启动后即可进入平差易的主界面。
PA2002的操作界面主要分为两部分——顶部下拉菜单和工具条,如下图所示。
PA2002主界面顶部下拉菜单几乎所有PA2002的主要功能都包含在顶部的下拉菜单中,例如文件读入和保存、平差计算、成果输出等。
文件:包含文件的新建、打开、保存、导入、平差向导和打印等。
如下图:顶部下拉菜单工具条文件菜单平差:控制网属性、计算方案、坐标推算、选择概算和平差计算等。
平差菜单成果:精度统计、图形分析、CASS输出、WORD输出和闭合差输出等。
当没有平差结果时该对话框为灰色。
成果菜单窗口:平差报告、网图、平差属性、网图属性等。
窗口菜单工具:坐标换算、解析交会、大地正反算、坐标反算等。
工具菜单由观测数据到平差成果用平差易做控制网平差的过程1)、控制网数据的录入。
2)、坐标推算。
3)、坐标概算。
4)、选择计算方案。
5)、闭合差计算与检核。
6)、平差。
7)、平差报告的生成和输出。
流程图:向导式平差向导即是按照应用程序的文字提示一步一步操作下去,最终达到应用目的。
PA2002提供了向导式平差,根据向导的中文提示点击相应的信息即可完成全部的操作。
它对PA2002的初学者有着极大的帮助,建议PA2002的初学者先应用向导来熟悉PA2002数据处理的全部操作过程。
本平差向导只适用于对已经编辑好的平差数据文件进行平差。
向导式平差的应用向导式平差需要事先编辑好数据文件,这里我们就以demo中的bjw4.txt文件为例进行操作。
第一步:进入平差向导首先启动“南方平差易2002”,然后用鼠标点击下拉菜单“文件\平差向导”。
平差向导请注意平差向导的中文提示和应用说明,并依据提示进行。
第二步:选择平差数据文件点击“下一步”进入平差数据文件的选择页面。
选择平差数据点击“浏览”来选择要平差的数据文件。
所选择的对象必须是已经编辑好的平差数据文件,如PA2002的Demo中实例BJW4。
对于数据文件的建立,PA2002 提供了两种方式,一是启动系统后,在指定表格中手工输入数据,然后点击“文件\保存”生成数据文件;二是依照附录A中文件格式,在Windows的“记事本”里手工编辑生成。
1112打开数据文件点击“打开”即可调入该数据文件。
如下图:调入平差数据文件第三步:控制网属性设置调入平差数据后点击“下一步”即可进入控制网属性设置界面,如下图:该功能将自动调入平差数据文件中控制网的设置参数,如果数据文件中没有设置参数则此对话框为空,同时也可对控制网属性进行添加和修改,向导处理完后该属性将自动保存在平差数据文件中。
点击“下一步”进入计算方案的设置界面。
13控制网属性设置第四步:设置计算方案设置平差计算的一系列参数,包括验前单位权中误差、测距仪固定误差、测距仪比例误差等。
该向导将自动调入平差数据文件中计算方案的设置参数,如果数据文件中没有该参数则此对话框为默认参数(2.5、5、5),同时也可对该参数进行编辑和修改,向导处理完后该参数将自动保存在平差数据文件中。
计算方案设置点击“下一步”进入坐标概算界面。
14 第五步:概算概算概算是对观测值的改化包括边长、高程和角度等。
当需要概算时就在“概算”前打“ ”,然后选择需要概算的内容。
点击“完成”则整个向导的数据处理完毕,随后就回到南方平差易2002的界面,在此界面中就可查看该数据的平差报告以及打印和输出。
控制网数据的录入控制网的数据录入分数据文件读入和直接键入两种。
凡符合PA2002文件格式(格式内容详见附录A)的数据均可直接读入。
读入后PA2002自动推算坐标和绘制网图。
PA2002为手工数据键入提供了一个电子表格, 以“测站”为基本单元进行操作, 键入过程中PA2002将自动推算其近似坐标和绘制网图。
如下图:电子表格输入下面我们介绍如何在电子表格中输入数据。
首先,在测站信息区中输入已知点信息(点名、属性、坐标)和测站点信息(点名),然后在观测信息区中输入每个测站点的观测信息。
“序号”:表示已输测站点个数,它会自动叠加。
“点名”:输入已知点或测站点的名称。
“属性”:用以区别已知点与未知点:00表示该点是未知点,10表示该点是有纵横坐标无高程的已知点,01表示该点是无纵横坐标有高程的已知点,11表示该已知点既有纵横坐标也有高程。
“X、Y、H”:分别表示该点的纵、横坐标及高程(X:纵坐标,Y:横坐标)。
“偏心距、偏心角”:表示该点测站偏心改正的距离和角度。
(不需要偏心改正时则可不输入数值)注意:下面的观测信息与上面的测站信息是相互对应的,当某测站点被选中时,观测信息区中就会显示当该点为测站点时所有的观测数据。
故当输入了测站点时需要在观测信息区的电子表格中输入其观测数值。
“照准名”:照准点的名称。
“方向值”:照准某点时的方向观测值。