小型电动遥控飞机制作图

小型电动遥控直升机制作以下文章是通过google翻译所得: Little tips about building your own RC helicopter Flying RC helicopter is really very exhilarating. Their versatility gives a RC pilot a complete access to the three-dimensional space in such a way that no other machines can! I have played RC helicopter for more than one year but still find that I have just learnt a few tricks that it can perform. There are generally two micro-helicopters

( indoor ) in the RC market. I have already planned to buy one of them as they can fly inside the living room and even take off on ours hand. Unlike those operated by gas, these electric helicopters are very clean and give out no terrible noise at all. In one nightfall, I visited a web site, which is about how to make a hand made RC helicopter. I was totally impressed and started designing my own helicopter. Here is my helicopter: 小秘诀是关于建立您自己的钢筋混凝土直升机飞行区局的直升机，实在是非常令人振奋的。他们的多才多艺给出了钢筋混凝土试验一个完整的获得三个三维空间，在这样一种方式没有其他机器可以！我有发挥的钢筋混凝土直升机以上的一年，但仍然觉得我刚才已经学到了一些技巧，它可以执行。有一般两个微型直升机（室内），在钢筋混凝土市场。我已计划购买其中一人，因为他们可以乘飞机内的客厅，甚至起飞，对我们的手。不像那些经营的气体，这些电动直升机，是很干净，并给予指出并没有可怕的噪音在所有。在一入夜，我访问了一个网站，这是有关如何制作手工钢筋混凝土直升机。我是完全的印象，并开始设计自己的直升机。这里是我的直升机

The plan of the helicopter had finally been completed. It is not very well drew. The current plan available is only for the fixed pitch design. Please click the above photo for the plan. 该计划的直升机终于完成。这不是很好的提请。根据目前的计划，可仅适用于固定摊位的设计。请按上述照片的计划。Length 410mm Height 150mm Flying Weight 250g (include 700mAh battery pack) Control system Hiller control system / fixed pitch Main rotor diameter 490mm Tail rotor span 146mm Transmission rate

1:18 (main rotor) 1:3.5 (tail rotor) Power speed 300 motor (main rotor) tail boom 280mm receiver GWS R4P ( 4 channel, 3.8g ) ESC Jeti 05

( main rotor, 5A, 9g ) JMP-7 ( tail rotor, 4A, 0.7g ) Gyro GWS-PG-03 ( 7g with case ) servo Hitec HS-50 * 2 ( 0.09sec/60° , 0.6kg/cm, 5.8g ) Battery Sanyo 700mAh * 7 ( 90g )

Making the Swashplate

Making the Swashplate Swashplate is the most sophisticated part of a RC helicopter. It seems to be a simple unit of a factory one. However, it is a whole new thing of making one by yourself. Here is my design based on my own little knowledge about the swashplate. What you need includes:斜盘式是最先进的一个组成部分钢筋混凝土直升机。这似乎是一个简单的单位，一家工厂之一。不过，这是一个整体的新事物，使一所自己。这里是我设计的基础上我自己的知识甚少，有关斜盘式。您所需

要的包括：

* 1 ball bearing ( 8*12) * 1 plastic spacer (8*12) * rod end set ( for holding of the aluminum ball in the swashplate ) * aluminum ball ( from ball linkage set 3*5.8 ) * aluminum ring * epoxy adhesive 一球轴承（ 8 * 12 ）一塑胶间隔（ 8 * 12 ）棒年底成立（持有的铝球，在斜盘式）铝球（从球的联系，设置3 * 5.8 ）铝环环氧胶粘剂The rod end set has first been cut into a round shape. It is then inserted into the plastic spacer as shown below: 该杆端设置首先被削减为一个圆形。这是然后插入到塑料间隔，如下所示：

Make sure that the aluminum ball placed in the rod end can be moved freely.

2 holes were drilled on the plastic spacer in order to house two screws that used to hold the ball linkage. 作出肯定的是，铝球，放置在杆端关节轴承可以提出自由。二洞钻于塑胶间隔，以便向内务两个螺丝用来举行球的联系。