手机数据线测试检验标准(Data cable Inspection Standard)

手机数据线检测标准Data cable Inspection Standard版本记录Version Records本文件属于公司秘密信息，请您恪守保密义务，勿向第三人透露。

谢谢合作。

This file is confidential. Recipient(s) is(are) obligated to maintain secrecy and is(are) not permitted to disclose the contents of this file to others. Thank you.1、目的Purpose为确保数据线的生产、检验工作有序进行，为过程质量控制、例行检验、最终成品检验和确认检验提供依据。

This standard is the data cable quality acceptance criterion, to ensure the data cable design and produce meet the quality requirements, make sure product quality, provide the judgment standard for the inspection;2、适用范围 S cope本标准适用本公司手机产品的各种数据线质量检验。

The standard will be applied to data cable’s quality evaluation and sampling inspection for all XXX products ;3、规范性引用文件Referred files手机可靠性测试标准；reliability test standard手机外观检验标准；handset appearance inspection standard4、检验工具 E quipment游标卡尺、硬度计、投影测试机、振动测试仪、拉力计、压力计、扭曲测试仪、盐雾机、摇摆测试机、自由跌落测试机、拔插测试机、高低温箱Vernier Caliper, Hardness Meter, Projective Tester, Vibration Tester, Tension Meter, Pressure Meter, Torque Meter, Salt Tester, Swing Tester, Free Fall Tester, Insertion and Draw Tester, Temperature Chamber.5、基本要求Requirement5.1 工作条件Working condition工作温度范围Working temperature range ：-20℃～65℃相对湿度Humidity：5%～90%大气压力Atmospheric pressure：70 KPa～106 KPa存储温度Store Temperature: -40℃～70℃5.2 外观要求Appearance requirement数据线表面应平整无划痕，外观无损伤、碎裂痕迹、镀涂层剥落、外露金属无锈；塑料制品不应有起泡、断裂、变形、烫伤、污溃；卡簧安装方向正确。

与手机连接的插头插入、取出方便；摇晃数据线，数据线内部应无晃动感，接头必须是模内注塑。

The data cable appearance should be good, no obvious nick, deformed, no plating peel off, no rusty metal and other damage. Plastic part should not be bubbly, broken, deformed and other damage. The spring snaps should be installed correctly. The connection between data cable and mobile phone should be convenient, and should not be loose; the connector shoulder should be insert molding.5.3 尺寸要求: Dimension线长Length:100cm(Min)，具体参照下图Refer to following picture：标准USB参考公头图Reference USB Plug connector：10PIN公头参考工程图10PIN USB Plug reference drawing：5PIN公头参考工程图5PIN USB Plug reference drawing：10PIN母座参考工程图10PIN USB Socket reference drawing：5PIN母座参考工程图5PIN USB Socket reference drawing：5.4线材及其结构Cable Material and Configuration主体规格Main Spec：Φ3.5*1000mm;颜色Color：黑色/白色Black/White；内芯线Core Wire：26AWG(7/Φ0.12BC)4C;(适用于USB2.0标准);线材结构Cable Configuration：5.5电气性能要求Electrical Characters：额定工作电压Rated working voltage：1~30V导线绝缘阻抗Insulation Impedance of Wire：DC/300V 10MΩMIN接触阻抗Contact Impedance：0.2Ω/m MAX导通阻抗Conductive Impedance：2ΩMAX耐压Rated Max Voltage：AC 500V (适用于USB2.0标准)6.可靠性测试R eliability：6.1 自由跌落测试Free fall drop test测试仪器Test equipment：20mm水泥地板20mm floor slab测试环境Test Circumstance：1）高度为Height :150cm；2）跌落10次Drop 10times。

判定标准Criteria：1）电性能正常，外壳不可破裂Electrical function is ok, and the plastic should not be broken。

6.2 拉力测试Tensile strength test测试仪器Test equipment：拉力计Tension meter；测试要求Test Requirement：1）使用5KG的拉力去拉数据线两端Tension under 5KG strength on the two ends of the data cable；2）保持60秒钟Retain 60 seconds。

检验标准Criteria：1）产品功能正常，线芯断线率不超过20%，被覆外皮不破裂，变形，断裂The function should be ok, and the damage happened on core wire should not be over 20%, cable skin should not be cracked ,deformed and broken down；6.3表面印刷测试Printing Test测试要求Test Requirement：1）参考xxx可靠性测试RCA测试标准，并记录检验结果Refer to the xxx reliability test standard to do the test, and record the result;2）字符酒精耐磨测试Character RCA：用沾酒精的布，90%的酒精浓度，5N／cm２的力来回擦200次Abrade the character with cloth contained 90% consistency alcohol under 5N/ cm２strength；检验标准Criteria：测试后整个测试表面原始的颜色不可改变，图案不可消失,油漆不露底。

The color should not be changed on the surface, the picture should be clear and the priming should not be shown.6.4盐雾测试Salty fog test:测试条件Test Condition：1）参考xxx可靠性测试盐雾测试标准，并记录检验结果Refer to the xxx reliability test standard to do the test, and record the result;6.5高温度存储测试High temperature store test测试要求与检验标准Test condition and Criteria：1）参考xxx可靠情测试高温存储测试标准，并记录检验结果；Refer to the xxx reliability test standard to do the test, and record the result;6.6低温度存储测试Low temperature store test测试要求与检验标准Test condition and Criteria：1）参考xxx可靠情测试低温存储测试标准，并记录检验结果；Refer to the xxx reliability test standard to do the test, and record the result;6.7温度循环测试Temperature cycle test测试要求与检验标准Test condition and Criteria：1）参考xxx可靠情测试温度循环测试标准，并记录检验结果；Refer to the xxx reliability test standard to do the test, and record the result;6.8恒温恒湿测试Constant temperature and humidity test测试要求与检验标准Test condition and Criteria：1）参考xxx可靠情测试恒温恒湿测试标准，并记录检验结果；Refer to the xxx reliability test standard to do the test, and record the result;6.9插拔寿命测试Plug insertion and pull out test测试条件Test condition：1）使用插拔测试仪Plug insertion and pull out machine；2）测试总周期为3,000次，每分钟插拔40次。