罗斯蒙特8800D涡街流量计HART菜单

Status 1 Device Status: Good 2 Communications: Polled
Revision Numbers 1 Universal Revision: 5 2 Field Device Revision: 2 3 Software Revision: 3 4 Hardware Revision: 1 Process 1 Transmitter Mode 2 Process Fluid 3 Fixed Proc Temp 4 Fixed Proc Density 5 Pipe I.D. 6 Installation Effect Flow Sensor 1 Reference K Factor 2 Compensated K Factor 3 Upper Sensor Limit 4 Lower Sensor Limi NOTE: Limits are only displayed if PV = Flow Temperature Sensor 1 T/C Failure Mode 2 Upper Sensor Limit 3 Lower Sensor Limi NOTE: Limits are only displayed if PV = Temperatur Meter Body 1 Wetted Material 2 Flange Type 3 Meter Body Serial Number 4 Body # Suffix 5 Meter Body #: 123456A
Process Conditions 1 Fixed Proc Temp 2 Change Proc Temp Units 3 Proc Pressure (abs) 4 Change Proc Pressure (abs) 5 Proc Compressibility Base Conditions 1 Base Temperature 2 Change Base Temp 3 Base Pressure 4 Change Base Pressure 5 Base Compressibility Density/Density Ratio 1 Fixed Proc Density 2 Density Ratio
Burst Variables 1 Burst Slot 0 2 Burst Slot 1 3 Burst Slot 2 4 Burst Slot 3 5 Burst Variable Mapping Identification 1 Tag: FT-100 2 Manufacturer: Rosemount 3 Model: 8800D 4 Final Assembly Number 5 Device ID: 123456 6 Write Protect: OFF Information 1 Date 2 Descriptor 3 Message Revision Numbers 1 Universal Revision: 5 2 Field Device Revision: 2 3 Software Revision: 3 4 Hardware Revision: 1
Initial Configuration 1 Basic Setup 2 Configure Display 3 Optimize DSP Process Configuration 1 Set Pipe I.D. 2 Set Process Temperature 3 Set Fixed Density 4 Set Density Ratio Output Configuration 1 Analog Output 2 Pulse Output 3 Variable Mapping 4 Special Units Signal Processing 1 Set Damping 2 Set Installation Effect 3 Low Flow Cutoff 4 Lowpass Corner Frequency 5 Trigger Level 6 Restore Default Filters
Communications 1 Polling Address 2 Burst Mode 3 Burst Option 4 Burst Variables
Variable Mapping 1 Primary Variable 2 2nd Variable 3 3rd Variable 4 4th Variable 5 Set Variable Mapping Process Variable Units 1 Volume Flow Units 2 Velocity Flow Units 3 Vel Measure Base 4 Mass Flow Units 5 Proc Temp Units 6 Elec Temp Units 7 Process Density Units Special Units 1 Base Volume Unit 2 Base Time Unit 3 Special Volume Unit 4 Conversion Number Conditions 2 Base Conditions 3 Density/Density Ratio Outputs 1 Analog Output 2 Pulse Output 3 Totalizer Signal Processing 1 Signal Strength: XX.XXX 2 Volume Flow: XXX.XX UOM 3 Shedding Frequency: XXXX Hz 4 Shed Freq at URV: XXXXX Hz 5 Filter Settings 6 Damping Display Primary Variable: ON Percent of Range: OFF Loop Current: OFF Total: ON Shedding Frequency: OFF Process Temperature: OFF Mass Flow: OFF Velocity Flow: OFF Volume Flow: OFF Pulse Frequency: OFF Electronics Temp: OFF Calc Process Density: OFF
Active Alerts (No Title) 1 Refresh Alerts Alert Name Same window will be available for Alerts 1-4 2 "Alert 1 Name" Description 3 "Alert 1 Image" 4 "Alert 2 Name" Recommended Actions 5 "Alert 2 Image" Primary Purpose Variables 6 "Alert 3 Name" (No Title) 1 "Primary Variable Title" Gauge 7 "Alert 3 Image" Same window will be available for Alerts 1-4 2 "Value" XX.XXX UOM …more as needed Image 3 "2nd Variable Title" Gauge Only Active Alerts show up here 4 "Value" XX.XXX UOM If no Active Alerts display text "No Active Alerts"; "Alert X Name" should be the actual alert name; "Alert X Image" should be the alert name with the word im Title to match variable name (Volume Flow, Velocity Flow, Mass Flow, or Process Temperature) 1&3 go to screen with gauge image Device Information 1 Tag: FT-100 2 Manufacturer: Rosemount Shortcuts 3 Model: 8800D 1 Device Information Device Information 4 Final Assembly Number: 123456 2 Configure Outputs 1 Device Information 5 Device ID: 123456 3 Simulate Flow 2 Sensor 6 Date 4 Optimize DSP 3 Jumpers and Switches 7 Descriptor 5 View Trends 8 Message 6 View Totalizer 9 Revision Numbers View Trends View Totalizer 1 Volume Flow Sensor 1 Total: XXXXX.XX UOM 2 Velocity Flow 1 Process 2 Totalizer Control: Stop 3 Mass Flow 2 Flow Sensor 3 Totalizer Configuration 4 Shedding Frequency 3 Temperature Senso 5 Pulse Frequency 4 Meter Body 6 Signal Strength 7 Electronics Temperature Jumpers and Switches 8 Process Temperature 1 Write Protect: OFF 9 Calculated Process Density 2 Alarm Direction: HIGH 1-9 Go to screen with chart image 3 Alarm Level: Rosemoun Process Temperature only available when Transmitter Mode = With Temp Sensor 4 High Alarm: 22.0 mA Calculated Process Density only available when 5 High Saturation: 20.8 mA Transmitter Mode = With Temp Sensor and Process Fluid = T-Comp Sat Steam 6 Low Saturation: 3.8 mA 7 Low Alarm: 3.75 mA
Sensor 1 Process 2 Flow Sensor 3 Temperature Sensor 4 Meter Body
Blue Text = Method Gray Text = RO
Variable Mapping 1 Variable Mapping 2 Process Variable Units 3 Special Units
8800D HART EDDL 375 Menu Tree
Home 1 Overview 2 Configure 3 Service Tools
Overview 1 Check Status 2 Primary Purpose Variables 3 Shortcuts
Blue Text = Method Gray Text = RO
8800D HART EDDL 375 Menu Tree
Home 1 Overview 2 Configure 3 Service Tools
Configure 1 Guided Setup 2 Manual Setup
Guided Setup 1 Initial Configuration 2 Process Configuration 3 Output Configuration 4 Signal Processing