太阳能充电宝品规格书
深圳市映红山光学有限公司-多功能充电宝说明书
太阳能充电器说明书一、产品结构：内置高容量储蓄锂电池（18650），IC智能过流过载保护，单晶硅光伏电池板2W，220V，50HZ单相交流，LED镇流驱动显示，整机由交流，USP直流，单晶硅光伏充电等多功能储藏电荷。
部份产品带LED灯手电照明，收音机功能，铝合金外壳。
二、产品特点：容电量大，华贵大方，携带方便，时尚高雅，节能环保，充电1小时搞定，特别适合出差，旅游，长途乘车，找工作，野外施工，商务会议等手机充电。
只要接入手机就能使用，并适用于数码照相机，DV，PDA，MP3，MP4，GPS，平板电脑及部份笔记本电脑电源充电，产品用途广泛。
三、技术参数：输入交流AC220V，50HZ，储存电能充电时间：1~3小时，直流DC3V接USB电脑接口，储存电能充电时间：2~5小时，光伏储存电能：6V，2W，60一150MAX，转换效率25%以上，储存电能时间：6~8小时，指示灯显示100%，表示储存电能充满，输出电压：4．5V，5V，6V，9V，12V等多个供电选择，充满电后自动恒压3．7~4．2V。
不会损坏手机，电流：2600MAH一5000MAH，最大10000MA。
手机充电时间1小时搞定。
四、使用方法：1、使用本产品前要交流充电，以提高内存电池的使用效率。
2、接口IN为输入储存电能充电，接口OUT为输出给手机充电或其它产品充电。
3、手机充电前要选好与手机相符合的电压档，一般选4．5V，视手机能量而定。
4、看手机屏信号是否处于充电状态。
五、注意事项：1、光伏充电时，要光伏正面向光直射，确保效果。
2、注意防潮，防高温，防划伤光伏表面。
3、请用厂家提供的专用数据充电适配线和转接头。
4、不可用短路或损坏的电池接入充电，否则会损坏充电宝。
5．没有显示充电，可能内存电能不足或接触不良。
7太阳能电源技术规格书模板
运输种类
轴向加速度(g)
横向加速度(g)
垂直加速度(g)
公路运输
2.0
1.2
1.2
海运
0.2
0.7
2.2
铁路运输
4.0
0.4
0.4
模块技术指标要求：
·电气匹配，在直射和散射时都能有效转换；
·电池作化学处理，减少反射；
·双备份触点，提高电路的可靠性；
·钢化玻璃罩能提供机械保护，提高光线的传送；
·层之间的层叠状电路，能防潮、提高稳定性和电气绝缘；
·坚韧的多层聚合衬板可耐磨，防破损和防潮；
·轻便的铝合金架带有一到两套安装孔和用于接地螺丝安装的中央孔；
太阳能板阵的最低转换效率应不小于12%，并经过国内/国外的权威部门认证。
每太阳能板阵应有一个带正负接线端子的汇流盒、板阵的内部连线和截止二极管。
汇流盒和太阳能板阵的连接及太阳能电池到汇流盒的输入之间应能防尘防水（至少满足IP55标准）。
太阳能板彼此之间应具有电气和机械的可互换性。某一太阳能板需移动和更换时，应无需特殊工具，在现场就很容易完成。
技术评分表：技术评分表是招标投标过程中通用的技术组评分标准
技术条件：各工程项目通用并统一的技术要求
质保期：是指供货商承诺的对所供产品因质量问题而出现故障时提供免费维修及保养的时间段
1.4项目总体要求
1.4.1资格要求
供货商所提供的太阳能电源系统应有类似规格产品在本规格书中所提供的环境条件下成功运行三年以上的经历。
注：g为重力加速度。
太阳能移动电源的中英文说明
太阳能移动电源的中英文说明
太阳能移动电源是针对无电或常停电的国家及地区设计制造的系列产品。
其主要用于简单的照明及小型家用电器使用，如节能灯、台式风扇、电视机、洗衣机、冰箱及电脑太阳能移动电源分6种：
a.10w功率以下的节能灯，
b.30w以下的电风扇或节能灯，
c.100w以下，除b外可另外加一台21寸电视机(太阳能电池板外接)
d.300w以下可除节能灯外另带动一台式电脑或同功率的其它电器。
e.纯市电充电600w车载移动电源并适合以上电器(方波逆变器，使用功率需小于450w)
f.纯市电充电1000w正弦波逆变器，可直接用于冰箱。
移动电源产品的使用时间主要取决于电瓶的容量及太阳能电池板的大小功率。
有110v-220v逆变器的输出是高压的要特别注意安全！防止触电。
一般正常使用时间2-8小时。
特别要求也可订做，也可用风光互补发电来弥补太阳能发电成本过高问题。
例如：实际使用功率大于500w的家庭用电，长时间工作的路灯等。
24W折叠便携太阳能应急充电器
太阳能移动电源
01 参数
03 使用说明 05 配件
目录
02 工作原理 04 注意事项
24W折叠便携太阳能应急充电器通过迷你调压稳压器输出5.5V电压，可以充手机，数码相机，MP3等电子产品， 也可搭配移动电源使用，随时随地供电。
参数
1.太阳能板:太阳能板峰值功率:24W2.工作电压:24V 3.输出电流:A 4.太阳能转换率:>17% 5.输出接口:DC3.5mm接口 6.调压稳压器输出5.5V电压(选配). 7.便携移动电源(选配).
工作原理
在阳光充足时，太阳能板在阳光下，产生电流电压，经过控制器板，给蓄电池组充电电脑相连接，就可以实现自由充电。使用迷你调压器即可实现 Iphone/ipad,手机、PDA、MP3、MP4、数码相机、PSP游戏机、iPhone、Blackberry、、GPS、蓝牙耳机、IPOD 等数码产品进行充电。产品使用时不可有物体遮挡太阳能板光源，尽可能让太阳能板最大限度接收太阳光,将光能 转化为电能使用。
注意事项
1.不可浸入带腐蚀性的液体中，这样会损坏产品。 2.请不要用尖锐物体刮擦太阳能电池板表面 3.用太阳能给充电器充电时,请将太阳能板朝上置于阳光直射处,以保证最佳充电效果 4.请不要在下雨天将充电器置于户外 5.非专业人员，不可打开外壳，以免发生危险。
配件
1.20款转接头, 10款手机转接头和笔记本电脑转接头. 2.调压器（24V到5V输出）(选配).
谢谢观看
驭光者·火鸟ELITE太阳能手提式移动电源箱 用户指南说明书
PHOENIX ELITE PORTABLE SOLAR GENERATOREN01 USER GUIDE驭光者·火鸟ELITE太阳能手提式移动电源箱CN18PHOENIX ELITE PORTABLE SOLAR GENERATORUser GuideIMPORTANT SAFETY INSTRUCTIONS PACKAGE CONTENTS FEATURESRECHARGING PHOENIX ELITE LCD SCREENPRODUCT OVERVIEW SPECIFICATIONS TROUBLESHOOTINGFREQUENTLY ASKED QUESTIONS WARRANTYOPERATING PHOENIX ELITE MAINTENANCE 171613131108070604030302Please read the User Guide carefully before recharging or operating your PHOENIX Elite.IMPORTANT SYMBOLSIndicates potentially dangerous conditions that could result in personal injury Indicates conditions or practices that could result in damages to the unit or other equipmentIndicates procedures or functions that are important for proper and safe operation of the unit and/or other equipmentCAUTIONCAUTION CAUTION CAUTIONWARNINGWARNINGWARNINGWARNINGWARNINGWARNINGNOTEDO NOT submerge the unit in water or operate the unit in the rain. Doing so may cause short-circuits, electric shocks, and/or fire.DO NOT place the unit near fire and/or heat the unit. Doing so may cause irreversible damages to the unit and/or battery explosion.DO NOT overload the unit. Please check the specifications of output ports and devices before operation.Please turn off the output ports when no devices are connected to the unit to prevent electric shocks.DO NOT dismantle or modify the unit. Doing so may cause irreversible damages to the unit and void warranty.CAUTIONDO NOT place the unit in high-temperature situations. Doing so may cause unit malfunction or component degradation.CAUTIONDO NOT expose the unit to strong electrostatic fields, strong magnetic fields, and/or radiation.CAUTIONPlease check the unit before each use. Stop using the unit if you notice unusual smells, heating, distortion, or any other abnormalities.DO NOT drop or strike the unit. Doing so may cause circuit failures and cracks in the casing.Please dispose of the product according to the local recycling and environmental regulations.Keep the unit out of the reach of young children.PORTABLE DESIGNFeaturing a portable briefcase design with a sturdy carrying handle, the PHOENIX Elite is the top choice for a weekend trip or an emergency.RENEWABLE ENERGYDesigned for off-grid applications, the PHOENIX Elite combines two highly efficient 10W monocrystalline solar panels for effortless battery replenishment.DIVERSE RECHARGING OPTIONSEngineered with convenience and versatility in mind, the PHOENIX Elite supports recharging from car sockets, AC adapters, USB-C wall chargers, and external solar panels.RELIABLE POWER SOURCEEquipped with a 300Wh rechargeable lithium-ion battery pack and multiple output ports, the PHOENIX Elite is ready to provide long-lasting power for a wide range of mobile devices and small appliances.1 x Renogy PHOENIX Elite Portable Solar Generator1 x AC/DC Adapter1 x Cigarette Lighter Plug to 5.5mm DC Adapter Cable1 x Solar Panel Connectors to 5.5mm DC Adapter Cable1 x USB-C to USB-C Cable1 x User Guide76 12345891011121314CIG Port Output Side DoorDC Output Ports QC USB-A Port USB-A Ports Hinges Input Side Door 15DC Input Port 16USB-C PD Port 17LED Flashlight 18Carrying Handle1914131211109Flashlight On/Off Button Main Power ButtonAC Output Mode On/Off Button DC Output Mode On/Off Button LCD Screen Built-in Solar Panels Latches AC Outlet 876543211516171819InputBatteryGeneralLithium-ion 14.4V20800mAh / 299.5Wh Battery Type Battery Voltage Battery CapacityBuilt-in Solar Panel DC Input Port USB-C PD Port Total9.8V / 2.04A, 20W Max 9-16.8V, 55W Max 16.8-30V, 100W Max5V / 3A, 9V / 3A, 12V / 3A, 15V / 3A, 20V / 3A, 60W Max 180W Max 413 x 308 x 100 mm / 16.3 x 12.1 x 3.9 inch 5.3 kg / 11.7 lb.ABS + PC 3W LED0-45 ℃ / 32-113 ℉-10-60 ℃ / 14-140℉20-90%Dimension Weight Material FlashlightNormal Operating Temperature Storage Temperature Operating / Storage HumidityOutputUSB-A Port (2)QC USB-A Port USB-C PD Port CIG PortDC Output Port (2)AC OutletTotal5V / 2.4A Max5V / 3A, 9V / 2A, 12V / 1.5A, 18W Max5V / 3A, 9V / 3A, 12V / 3A, 15V / 3A, 20V / 3A, 60W Max 13.6V / 9A Max 13.6V / 4.5A Max 110V / 60Hz (US, JP, CA)220V / 50Hz (AU, EU, CN)200W Rated, 300W Surge Pure Sine Wave300W MaxThe LCD Screen will be lit when the PHOENIX Elite is being recharged or turned on to display the recharging and operating status of the PHOENIX Elite. Please refer to the following table to interpret the information displayed on the LCD Screen.The Battery Level is displayed as a ring composed of 10 segments with a percentage in the center. The ring and percentage appear when the PHOENIX Elite is being recharged or is turned on. When recharging the PHOENIX Elite, a lightning bolt will appear above the percentage. The ring will be lit segment by segment with the increasing percentage until the PHOENIX Elite has been fully recharged. As the PHOENIX Elite is used to power other devices, the ring segments will go out one by one with the decreasing percentage. When the battery level is lower than 10%, the last ring segment and the percentage will flash.IconNameDescriptionBattery LevelThe AC Output Mode is displayed as a rectangle with the words ‘AC Output’ inside. The rectangle appears when the AC output mode is activated with the AC Outlet turned on. The rectangle disappears when the AC output mode is deactivated with the AC Outlet turned off.AC Output ModeAC Output The DC Output Mode is displayed as a rectangle with the words ‘DC Output’ inside. The rectangle appears when the DC output mode is activated with the USB-A Ports, QC USB-A Port, USB-C PD Port, CIG Port, and DC Output Ports turned on. The rectangle disappears when the DC output mode is deactivated with the USB-A Ports, QC USB-A Port, USB-C PD Port, CIG Port, and DC Output Ports turned off.DC Output ModeThe Built-in Solar Panel Input is displayed as a sun with 5 bars below it. The sun and bars appear when the PHOENIX Elite detects input power from the Built-in Solar Panel. The number of bars demonstrates the strength of solar irradiance.Built-in Solar Panel InputThe Input Power is displayed as a wattage with the word ‘Input’ above it. The wattage appears when the PHOENIX Elite is being recharged.Input PowerThe Output Power is displayed as a wattage with the word ‘Output’ above it. The wattage appears when the AC output mode or the DC output mode is activated.Output PowerThe Error Code is displayed as a 3-digit code starting with the letter ‘E’. The code appears when the PHOENIX Elite encounters abnormal conditions.Error CodeDC OutputIf the [Error Code] icon appears, the PHOENIX Elite may need special attention. Please refer to the TROUBLESHOOTING section for help.CAUTIONTo maximize the battery life, please ensure that the PHOENIX Elite is fully recharged before operating or storing.To shorten the recharge time, it is highly recommended to disconnect all loads while recharging the PHOENIX Elite.CAUTIONNOTEThe above recharge times are based on conditions when the PHOENIX Elite is recharged at full speed with no loads connected to it.NOTEThe LCD Screen will go out if the input power of the Built-in Solar Panels is lower than 5W and no operations are made within 60 seconds. Press the AC Output Mode On/Off Button or DC Output Mode On/Off Button to relight the LCD Screen.NOTEThe recharge time via the Built-in Solar Panels is highly dependent on solar irradiance and ambient temperature.NOTERecharge TimeRecharge via Built-in Solar Panel: 20 Hours Recharging via Built-in Solar PanelFor optimal recharging performance, it is highly recommended to recharge the PHOENIX Elite using the Built-in Solar Panels on bright sunny days free of scattered clouds.Recharging via External Solar PanelFor optimal recharging performance, it is highly recommended to recharge the PHOENIX Elite using an external solar panel (not included) on bright sunny days free of scattered clouds.Place the external solar panel under direct sunlight. Steer clear of trees or branches that can shade the external solar panel and slow down the recharging process.Place the PHOENIX Elite in an open area. Open the Latches and adjust the angle of the Hinges to expose the Built-in Solar Panels to direct sunlight. Steer clear of trees or branches that can shade the Built-in Solar Panel and slow down the recharging process.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon, [Built-in Solar Panel Input] icon, and [Input Power] icon appearing.Recharge via External Solar Panel: 4 HoursRecharge via both Built-in Solar Panel and External Solar Panel: 3.5 Hours Recharge via AC/DC Adapter: 6 Hours Recharge via Car Socket: 6 HoursRecharge via USB-C PD Wall Charger: 6 HoursRecharge via both AC/DC Adapter and USB-C PD Wall Charger: 3 HoursUse the included Solar Panel Connectors to 5.5mm DC Adapter cable to connect the external solar panel to the DC Input Port of the PHOENIX Elite. Place the PHOENIX Elite in the shade to prevent it from overheating.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level]icon and [Input Power] icon appearing.Compatible External Solar Panels:Renogy Monocrystalline Solar Panel: 50W, 80W, 100W, 160WRecharging via AC/DC Adapter Plug the PHOENIX Elite into a wall outlet through the DC Input Port using the included AC/DC Adapter.Renogy Polycrystalline Solar Panel: 50W, 100WRenogy ECLIPSE Series Solar Panel: 100WRenogy Monocrystalline Foldable Solar Suitcase w/o Controller: 100WRenogy ECLIPSE Series Foldable Solar Panel w/o Controller: 100W, 200WRenogy Flexible Solar Panel: 50W, 100W, 160W, 175WRenogy E.FLEX Series Portable Solar Panel: 50W, 100W, 120W CAUTION WARNING NOTEElectrical shock can occur if the Solar Panel Connectors to 5.5mm DC Adapter Cable isdamaged or frayed. DO NOT use a damaged or frayed cable to recharge the PHOENIX Elite.Please ensure that the open circuit voltage of the external solar panel does not exceed 30V orfall short of 9V.The recharge time via the external solar panel is highly dependent on solar irradiance andambient temperature.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon and [Input Power] icon appearing.Recharging via Car SocketPlug the PHOENIX Elite into a car socket through the DC Input Port using the included Cigarette Lighter Plug to 5.5mm DC Adapter Cable.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon and [Input Power] icon appearing.WARNINGElectrical shock can occur if the AC/DC Adapter is damaged. DO NOT use a damaged AC/DC Adapter to recharge the PHOENIX Elite.WARNING DO NOT use a third-party AC/DC adapter to charge the PHOENIX Elite. Doing so may cause the AC/DC adapter to overheat and/or fire.WARNING Electrical shock can occur if the Cigarette Lighter Plug to 5.5mm DC Adapter Cable is damaged or frayed. DO NOT use a damaged or frayed cable to recharge the PHOENIX Elite.CAUTIONPlease disconnect the PHOENIX Elite from the car socket when starting the engine. Electricalsurges from the alternator when starting may damage the PHOENIX EliteRecharging via USB-C PD Wall ChargerFor optimal recharging performance, it is highly recommended to recharge the PHOENIX Elite using a USB-C PD wall charger (not included) with a high power rating.Plug the PHOENIX Elite into a wall outlet through the USB-C PD Port using the USB-C PD wall charger and the included USB-C to USB-C Cable.The PHOENIX Elite will begin to recharge automatically. The LCD Screen will be lit with the [Battery Level] icon and [Input Power] icon appearing.WARNINGElectrical shock can occur if the USB-C PD wall charger is damaged. DO NOT use a damagedUSB-C PD wall charger to recharge the PHOENIX Elite.Recommended USB-C PD Wall Chargers:Apple USB-C Power Adapter: 30W, 61W, 87W, 96WOperation Time Battery Powered Devices:Google USB-C Power Adapter: 45WOperating the PHOENIX Elite at high temperature above 113℉ (45℃) or at low temperatures below 32℉ (0℃) can result in battery performance degradation and service life shortening. Foroptimal battery performance and maximum battery life, it is highly recommended to operate the PHOENIX Elite at room temperatures. CAUTION OPERATING PHOENIX ELITENumber of Full Charges =Device Battery Capacity (Wh)299.5Wh x 70%Powering DevicesPress the Main Power Button to turn on the PHOENIX Elite. The LCD Screen will be lit with the [Battery Level] icon appearing.Compatible DevicesUSB-A Ports / QC USB-A Ports: Smart Watch, Electronic Book, Smart Phone, Tablet, Action Camera, Digital Camera, Bluetooth Speaker, Wireless Headphone, Drone, and other USB-A enabled devicesUSB-C PD Ports: Smart Phone, Tablet, Laptop, Handheld Game Console, DSLR Camera, and other USB-C enabled devicesCIG Port: Portable Refrigerator, Car Vacuum, Car Air Fan, CPAP Machine, and other car powered devices DC Output Ports: LED Strip Light, Modem, Router, Motor, and other DC powered devicesAC Outlet: Laptop, Monitor, TV, Game Console, Inkjet Printer, Portable Projector, Light Bulb, and other AC Powered DevicesTo use the USB-A Ports, QC USB-A Port, USB-C PD Port, CIG Port, or DC Output Ports, first press the DC Output Mode On/Off Button to activate the DC output mode. The [DC Output Mode] icon and [Output Power] icon will appear. Then, connect the device(s) to the port(s) for power. The [Output Power] icon will show the real-time output power. When not using the port(s), long press the DC Output Mode On/Off Button to deactivate the DC output mode. The [DC Output Mode] icon and [Output Power] icon will disappear.To use the AC Outlet, first press the AC Output Mode On/Off Button to activate the AC output mode. The [AC Output Mode] icon and [Output Power] icon will appear. Then, connect the device to the outlet for power. The[Output Power] icon will show the real-time output power. When not using the outlet, long press the AC Output Mode On/Off Button to deactivate the AC output mode. The [AC Output Mode] icon and [Output Power] icon will disappear.When no device is connected to the PHOENIX Elite, press the Main Power Button again to turn it off.DC Powered Devices:Working Hours =Device Power Rating (W )299.5Wh x 95%AC Powered Devices:Working Hours =Device Power Rating (W )299.5Wh x 85%NOTE The above estimation formulas only apply when the PHOENIX Elite has been fully recharged and the device does not draw too much power.NOTEActual number of full charges and working hours may vary due to different powering methods and device operation status.WARNINGThe PHOENIX Elite can provide up to 300W total output power. Allocate the total output powerrationally and follow the specifications of each output port. DO NOT overload the PHOENIXElite. If the total output power should exceed 300W, the AC Outlet will be shut off.Using LED FlashlightPress the Main Power Button to turn on the PHOENIX Elite. The LCD Screen will be lit with the [Battery Level] icon appearing.When not using the LED Flashlight, press the Main Power Button to turn off the PHOENIX Elite.The LED Flashlight has three lighting modes: bright (100% brightness), dim (50% brightness), and SOS. Press the Flashlight On/Off Button to turn on the LED Flashlight, switch lighting modes, and turn off the LED Flashlight. Long press the Flashlight On/Off Button to turn off the LED Flashlight no matter what lighting mode it is on.To prolong the service life of the PHOENIX Elite, keep it away from water, dust, and dirt. DO NOT leave the PHOENIX Elite in harsh environments.Keep the PHOENIX Elite away from corrosives, fire, and heat sources.Keep the PHOENIX Elite recharged when not in use and avoid connecting devices with high power ratings when the battery level is low.If the PHOENIX Elite does not operate normally, please refer to the following table for possible causes and corrective steps.If the following corrective steps do not work, please contact the Renogy technical support team for help. Refer to the last page of the User Guide for contact information.If the PHOENIX Elite is not used frequently, keep its battery level at around 50%. Store the PHOENIX Elite in a clean, dry, and well-ventilated environment with a temperature around 77℉ (25℃) and a humidity no higher than 75%. Recharge the PHOENIX Elite at least once every two months.NOTE The PHOENIX Elite may not be compatible with the devices that require high current impulses despite their conformity with the output ports specifications.NOTEThe PHOENIX Elite may not be able to deliver exactly 299.5Wh of energy when poweringdevices with high power ratings. Battery high temperature protection may be triggered when the PHOENIX Elite is operating at full load. Cool down the PHOENIX Elite before resuming operation. CAUTIONWhen using the AC Outlet, keep 4 inches of space on either side of the PHOENIX Elite to guarantee efficient heat dissipation.CAUTION When the battery level drops to 0%, the PHOENIX Elite will turn off automatically. Please recharge the PHOENIX Elite as soon as possible to avoid permanent damage to the battery.CAUTION When the battery level drops below 10%, use of the AC Outlet will be disabled. If the total outputpower still exceeds 200W, use of the CIG Port and DC Output Ports will be subsequentlydisabled. DO NOT connect devices with high power ratings to the PHOENIX Elite when the battery level is low. CAUTIONDisconnect all the power source(s). Discharge the unit untilthe [Error Code] icon disappears.Error CodePossible Causes Corrective Steps E01Battery Over-voltage Disconnect all the electrical load(s). Recharge the unit untilthe [Error Code] icon disappears.E02Battery Under-voltage Stop using the unit. Contact the Renogy technical supportteam for help.E03Battery Cell Imbalance Stop using the unit. Contact the Renogy technical supportteam for help.E04BMS Communication Failure Disconnect all the power source(s) and electrical load(s).Cool down the unit until the [Error Code] icon disappears.E05Battery High Temperature (Charge)Disconnect all the power source(s) and electrical load(s).Warm up the unit until the [Error Code] icon disappears.E06Battery Low Temperature (Charge)Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E07DC Input Port Over-voltage Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E08DC Input Port Under-voltage Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E09USB-C PD Port Input Over-voltage Disconnect the power source. Check the voltage rating ofthe power source. Connect only the power source withcompliant voltage rating to the unit.E10USB-C PD Port Input Under-voltage Reconnect all the power source(s). If the [Error Code] iconpersists, stop using the unit. Contact the Renogy technicalsupport team for help.E11Charge Over-current Disconnect all power source(s) and electrical load(s). Cooldown the unit until the [Error Code] icon disappears.E12Battery High Temperature (Discharge)Disconnect all power source(s) and electrical load(s). Warmup the unit until the [Error Code] icon disappears.E13Battery Low Temperature (Discharge)Disconnect the electrical load(s). Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E14USB-A Ports Output Over-voltageContact the Renogy technical support team for help.Under-voltage Disconnect the electrical load(s). Remove the shortcircuit(s). Press the DC Output Mode On/Off Button to clearthe [Error Code] icon. Connect only the electrical load(s)with compliant current ratings to the unit.E16USB-A Ports Output Over-current/Short-circuit Disconnect the electrical load(s). Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E17DC Output Ports/CIG Port Output Over-voltage Disconnect the electrical load(s). Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E18DC Output Ports/CIG Port Output Under-voltage Disconnect the electrical load(s). Remove the shortcircuit(s). Press the DC Output Mode On/Off Button to clearthe [Error Code] icon. Connect only the electrical load(s)with compliant current ratings to the unit.E19DC Output Ports/CIG Port Output Over-cur-rent/Short-circuit Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E20QC USB-A Port Output Over-voltage Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E21QC USB-A Port Output Under-voltage Disconnect the electrical load. Remove the short circuit.Press the DC Output Mode On/Off Button to clear the [ErrorCode] icon. Connect only the electrical load with compliantcurrent ratings to the unit.E22QC USB-A Port Output Over-current/Short-circuit Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E23USB-C PD Port Output Over-voltage Disconnect the electrical load. Reactivate the DC outputmode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E24USB-C PD Port Output Under-voltage Disconnect the electrical load. Remove the short circuit.Press the DC Output Mode On/Off Button to clear the [ErrorCode] icon. Connect only the electrical load with compliantcurrent ratings to the unit.E25USB-C PD Port Output Over-current/Short-circuit Disconnect the electrical load. Remove the short circuit. Letthe unit stand for 10 seconds. Press the AC Output ModeOn/Off Button to clear the [Error Code] icon. Connect onlythe electrical load with compliant power ratings to the unit.E26AC Outlet Output Overload/Short-circuitFirst, make sure that the unit has been turned on by pressing the Main Power Button. If the LCD Screen does not light up after pressing the Main Power Button, please recharge the unit as soon as possible. Then, make sure that the output ports have been turned on by pressing the AC Output Mode On/Off Button and/or DC Output Mode On/Off Button. Finally, make sure that the connected devices conform to the specifications of the output ports. If the [Error Code] icon appears, please see the TROUBLESHOOTING section or contact the Renogy technical support team for help. Refer to the last page of the User Guide for contact information.Contact the Renogy technical support team for help.Over-voltageDisconnect the electrical load. Reactivate the AC output mode. If the [Error Code] icon persists, stop using the unit.Contact the Renogy technical support team for help.E28AC Outlet OutputUnder-voltage Disconnect all the power source(s) and electrical load(s).Cool down the unit to the room temperature. Press the ACOutput Mode On/Off Button to clear the [Error Code] icon.E29Inverter High Temperature Disconnect all the electrical load(s). Press the AC OutputMode On/Off Button to clear the [Error Code] icon.Reallocate the total output power. E30Total Output Overload1. Why doesn't the PHOENIX Elite power external devices?No, the battery in PHOENIX Elite is not replaceable. Do not try to dismantle the PHOENIX Elite and replace the battery by yourself. Doing so may cause irreversible damages to the unit and/or battery explosion.2. Can I replace the battery in the PHOENIX Elite?No, the PHOENIX Elite cannot be chained together or with other rechargeable AC power supplies. If you are looking for a rechargeable AC power supply with a large capacity,, please visit our website or contact us for more options. Refer to the last page of the User Guide for contact information.3. Is the PHOENIX Elite chainable?No, the PHOENIX Elite is not waterproof. Please keep the unit away from moisture. Do not submerge the unit into water or operate the unit in the rain. Doing so may cause short-circuit, electric shocks, and fire.4. Is the PHOENIX Elite waterproof?The battery capacity of the PHOENIX Elite is rated at 0.2C. When the PHOENIX Elite is powering devices with high power ratings, the internal resistance of the battery will turn more energy into heat and lower the energy conversion efficiency. As a result, you may not get exactly 299.5Wh of energy.5. Why doesn't the PHOENIX Elite last as long as I expect?RENOGY products are covered by a 12-month limited warranty from the original purchase date. If any problems occur, please contact us for assistance. Refer to the last page of the User Guide for contact informa-tion.We only provide after-sales services for products that are sold by RENOGY or retailers and distributors authorized by RENOGY. If you have purchased your unit from other channels, please contact your seller for more information about return and warranty.Please register your purchase(s) directly at /support/tickets/new or your region’s corresponding website so that we can stay in touch and contact you in the unlikely event that a safety recall is required.驭光者·火鸟ELITE太阳能手提式移动电源箱用户指南安全操作准则产品配件产品特性为火鸟Elite充电LCD 屏幕产品概况产品参数故障排除常见问题售后质保使用火鸟Elite 维护343331312926252422212120请在为本机充电或使用本机前仔细阅读用户指南。
太阳能充电器说明书
太阳能充电器说明书规格参数太阳能输出: 5V/2400mA（阳光充足下）输入：5V/2A 输出：5V/3A（max）功能指示1 外接太阳能充电器并接输入端口2 太阳能充电指示灯3 USB输出端口4 大功率单晶硅太阳能板5 挂绳孔批准：审核：编制：产品简介· 本产品为户外便携式太阳能充电包，小巧玲珑，方便携带。
配备6片大功率的单晶硅太阳能板，高达 20％ 的转换率，输出电流高达2400mA, 为您的手机、IPAD或其他小设备充电。
在享受大自然阳光的同时为您提供源源不断的绿色能源，是您外出旅游出行的必备佳品。
为设备充电1、在有阳光的地方打开太阳能产品，使太阳能板接受太阳的45°照射，太阳能指示灯绿灯亮，这时USB输出可以输出高达5V/2.4A的电流为您的电子产品进行充电。
2、为获得更大的电流，此产品可以两个并联使用，并联后可以获得最大5V/3A的电流，实现快速充电。
温馨提示：本产品需要在阳光下使用。
本太阳能面板不能直接存储电源，如果您想存储电源，您可以使用它为移动电源充电。
如果产品不能工作，请检查 USB 接口是否正确插入太阳能面板。
工作后请记住，卸下USB插头。
12345User manualSpecification parameterSolar charging :5V/2400mA(In full sunshine)Input :5V/2AOutput :5V/3A （max ）批准：审核：编制：·Product introduction·The product is an outdoor portable solar chager, small and exquisite, easy to carry. Equipped with 6 high-power mono-crystalline silicon solar panels, high transmit efficiency 20%, up to 2400mA max charging current, It can charge mobile phone ，IPAD or other small mobile devices. It willprovide you with green energy while enjoying the natural sunshine ,which will be your travelnecessity.Charger the device1、Open the solar energy product in a place with sunlight, so that the solar panel receives 45° illumina-tion from the sun, the solar indicator is green, and the USB output can up to 5V/2.4A to charge your electronic products.2、For more current , It can be used in parallel for two or three products. After parallel ,the maximum current output : 5V/3A can be obtained to achieve fast charging.Tips: This product needs to be used in the sun. This solar panel cannot store power directly. If you want to store power, you can use it to charge mobile power. If the product does not work, check that the USB connector is properly inserted into the solar panel. Remember to remove the USB plug after work.Function indication1.External solar charger connected to the input port2.Solar charging indicatorB output port4.High power mono-crystalline silicone solar panelnyard hole12345。
泰康移动太阳能可移动电源系统说明书
Tycon® RPMS24-360-650 Installation Instructions Congratulations on your purchase of the Tycon Mobile Solar Pro™ portable power system. Please take a few minutes to review these instructions before startup of the power system.Caution! Voltage from the solar panels can exceed 65VDC. When connected to grid power, the AC voltage input will carry 120VAC or 240VAC. Be extremely careful when modifying any wiring or working around the solar controller or AC/DC battery charger. High Voltage can cause serious injury.Typical Application with Wireless radio, Cameras and Wind Turbine OptionNotes:1.The basic trailer systemcomes complete with abattery control box outfittedwith eight 6V 180Ahbatteries, a 40A MPPT solarcontroller with 20A loadoutput, a 900W AC/DCBattery Charger, a 24VDC to56VDC 5A converter, aTPDIN-Monitor-WEB2 remotepower monitor, a 18’pneumatic extension mastwith 12V air-pump, a junctionbox at top of pole with a 5Port Gigabit versatile PoEswitch, and 650W of solarpanels with travel cover.2.When travelling, werecommend to always usethe solar panel cover to helpprotect the solar panels fromflying road debris. Make sureall bolts and nuts are tight.Also, the solar panels need tobe set for 10° position (nearlyhorizontal) and secured withthe included ratchet straps.3.When parked, even forstorage, we recommend toalways extend the 4stabilizers to prevent trailer damage from high winds.4.There are multiple components included in the trailer system. Each component has its ownuser guide; therefore, this user guide will just touch on the system basics.Procedures:1) Trailer Startupa) Park the trailer in such a way that when deployed, the solar panels won’t be shaded by theextension mast during peak sun. This usually means that the front of the trailer will be facing North. Solar panels need to be facing due South in the northern hemisphere.b) There are 4 outrigger stabilizers thatca n be extended 15” or 30”. Extendthese outriggers and use them to levelthe trailer.c) Make sure both red disconnectswitches are set to the OFF position.d) Set solar panels to face South and setthe tilt angle. Tighten all the adjustmentbolts. Optimum Solar panel tilt dependson latitude and time of year. There is ahandy calculator on to help you determine the best tilt anglefor your area.2) Powering up the systema) Note: The solar controller should always be connected to the batteries before being suppliedwith solar power.b) The system ships with two 30A fuses removed from the batterycables. Install both fuses to power up the system. The fusemay spark when inserted. This is normal.c) Turn the red battery disconnect switch to ON, then turn on thered solar disconnect switch to ON. The MPPT solar controllerwill powerup. The MPPT solar controller has a load outputwhich supplies power to the TPDIN-Monitor and the 24VDC to56VDC converter. Press the red SET button on the MPPT solarcontroller to turn the load on and off.d) The TPDIN-Monitor-WEB2 controls the power going to the topof the extension pole through two of the on-board relays. RelayCH1 controls the 56V supply. Relay CH2 controls the 24V supply. By default, these relays are closed. The TPDIN-Monitor-WEB2 allows control of the relays using manual control or based on measured parameters or ping. To find out more about the TPDIN-Monitor-WEB2 features and use, refer to the individual product user guide. The unit ships with DHCP client enabled and fallback IP is 192.168.1.63) Pneumatic Extension Mast - Raisinga) The pneumatic extension mast is raised using a 12V automotive air pump. The 12V for thepump is supplied from the 24V batteries using a 24V to 12V DCDC converter. There is apressure regulator with air valve used to raise or lower the mast. The mast has mechanical locks at 9’,12’,15’ and 18’ positions so the mast can be raised to any of these pre-definedheights. It takes about 1 minute to fully extend the mast using the air pump.b) Near the top of the mast, there is a die cast aluminum enclosurehousing a TP-SW5G-VERSA PoE gigabit switch. The input tothe switch is 56VDC and the outputs are as follows: Port 1 60WHigh PoE(4 pair); Port 2-4 802.3at 30W; Port 5 24V 12WPassive PoE. If it is necessary to connect a laptop orcomputer to the switch, connect to port 2,3 or 4 only.Connecting to port 1 or 5 could cause damage to yourcomputer Ethernet port.c) A wire terminal is included inside the housing to supply 24VDC15A unregulated and 56VDC 5A regulated.d) Turn off the voltage output from the MPPT solar controller by pressing the SET button. Mountequipment and connect the equipment to either the PoE switch or the wire terminal, asrequired. Power up the load by pressing the SET button on the MPPT solar controller. Once the equipment is connected and tested, the mast can be raised.e) Raise the mast by turning the air flow valve to the “UP” position. Turnon the 12V air-pump using the toggle switch. Note: The pressureregulator at the airflow valve should be set to 30PSI.f) You will hear the mechanical locks click into position as the mast israised. You can turn off the 12V air-pump at an intermediate height orafter the mast is fully extended. Once the mast is extended turn theairflow valve to the center position.4) Pneumatic Extension Mast - LoweringNote: If mast has been extended for a long time it may become depressurized and will need to firstbe pressurized using the air pump before attempting to lower it.a) Lowering the mast is a little tricky. Don’t relieve all the pressure then pull themechanical lock rings. This will cause the mast to fall and bang against thelower section. This could damage equipment mounted on the mast.b) To lower the mast slowly:i) Turn the air flow valve to the “DOWN” position. Immediately pull the bottom lock ring. Themast will begin to collapse.ii) When the mast section is about half way down, pull the next lock ring. Repeat till all the lock rings are pulled and the mast has collapsed fully.5) Charging the batteries from AC powera) The batteries can be charged using 115VAC or 230VAC grid power. This is useful if you wantto fully charge the batteries before each deployment.b) CAUTION: Make sure to set the voltage switch on the TP-BC48-900 battery charger to the correct AC voltage. Default is115VAC. Failure to set the correct voltage will damage thebattery charger.c) Connect an extension cord to the weatherproof AC receptacleon the back of the battery/equipment box. Connect theextension cord to the proper 10A AC voltage outlet. The battery charging process will startwithin a few minutes. It should take about 5hrs minimum to fully charge the dischargedbatteries.6) MPPT Solar Controllera) The advanced MPPT solar controller measures solar voltage andcurrent, battery voltage, load current and temperature. You can scrollthrough the various readings on the display by pressing the up anddown arrow keys on the controller. Please refer to the solar controlleruser guide for detailed info.b) There is a Bluetooth interface included so you can check status of thesystem using your smartphone without having to open the equipmentenclosure. The range is about 15’. Please refer to the TP-SC-BT1user guide for more info.7) Misc. Informationa) The enclosure includes a thermostatically controlled fan. The fan will turn on automatically ifthe temperature inside the enclosure exceeds 45C.b) The batteries used in the system are GEL type sealed lead acid batteries. They aremaintenance free and should last at least 5 years. Caution: Never store the batteries in adischarged state, especially in cold temperatures or else the battery life will be reduced.Always store the batteries fully charged.c) A second locking enclosure can be added to the trailer platform in order to store userequipment.d) A wind turbine option is available to add a second source of power to the system. The windturbine mounts to a separate foldable mast system which is included in the optional kit.e) Replacement fuses:i) Battery Cables: ATC/ATO (.75”) Automotive Fuse 30Aii) AC/DC Battery Charger: 6x30mm 25A glass fuseSchematic:。
太阳能智能移动电源使用说明书2010
太阳能智能充电器/移动电源一、产品介绍：本产品是一款多用途的太阳能智能充电器/移动电源，内置高容量可充电聚合物锂电池，太阳能电池板功率最高可达1.6w。
通过智能MCU输出多组电压，可随时随地对你的手机、数码相机、PDA、PSP、GPS、DV、MP3、MP4家庭节能设备等进行充电或供电。
本产品具有安全可靠，容量大，寿命长，功能多等优点。
金属外壳设计、时尚高雅、携带方便。
二、使用方法：注：本产品在初次使用时，请在使用前对本产品进行两次以上完全充、放电，以提高内置电池的使用效率。
请按下面步骤使用：1、使用之前请给本产品充电。
有三种方法可选择：A、太阳能充电:打开产品，放置于太阳直射处或强光上，太阳光将自动转化为电能自动为内置的锂电池进行充电。
此时产品的LED指示灯为红色，表示正在充电，当电池充满后，LED指示灯将变为绿色。
（内部设计电路有自动断电保护功能）B、电脑USB对产品充电:将产品用USB线连接到电脑USB端口，此时产品的LED指示灯为红色，表示正在充电，当电池充满后，LED指示灯将变为绿色。
（内置先进的电源管理芯片不会对你的PC产生任何的危害）C、用交流适配器充电：充电时USB指示灯会亮起，产品的LED指示灯为红色，表示正在充电，当电池充满后，LED指示灯将变为绿色，并关闭所有的输出。
另外，还可使用车载充电器对本产品充电。
2、当给您的手机或数码产品充电前，请仔细查看您的产品说明书或电源适配器，了解您产品的充电电压，然后按ON／OFF按钮(3秒一5秒)即可开机，开机时，红色LED电压指示灯亮，开机后产品默认输出4．8V，长按调节按钮(3秒一5秒）即可以调节输出4．8、5．8V、8．4V、9.0V。
每长按一次，可调整一次电压输出，调节好电压后，将充电转换线的USB 5P插头连接到本产品，再将另一头与相应的转接头连接，然后再连接到您的产品上，即可进行充电。
充电时，在您的手机和数码产品上将显示正在充电的提示，您可以在进行充电的同时使用手机进行通话。
ZH-S804(12V18AH) 30W 太阳能发电系统(可给笔记本充电) 说明书
ZH-S804(12V18AH) 30W太阳能发电系统（可给笔记本充电）使用说明书一、产品型号: ZH-S804(12V18AH)二、1.尺寸：太阳能板：335*740*25MM箱体：250*120*210-232MM2.重量：太阳能板：3.3KG 箱体：7.68KG三、产品参数:蓄电池：12V18AH 216W(可支持1W的照明用灯连续工作216小时、手机电池可以连续充55个、MP3电池可以连续充110个) 太阳能电池板：30W18V(以广州的天气为例，平均一天的正常发电量是138W，可供1W灯连续工作138小时、充手机电池可以连续充37个、充MP3电池可以连续充74个)输出电压范围： 3.3V、5.0V、8.4V、12V（可调式）电流输出最大值：USB输出1A、DC输出3A输入接口：1个DC接口，输入电压15-25V。
输出接口：4个，包括：两个USB输出电压是：3.3V/5V/8.4V可调电压，电流：1A、两个DC输出电压12V，电流3A。
开关：2个，椭圆型为总开关，圆型开关为USB输出开关。
后面方形为总开关。
指示灯：6个从左至右分别为：太阳能指示灯，蓄电池指示灯，12V输出指示灯，8.4 V输出指示灯，5 V输出指示灯，3.3 V输出指示灯。
四、附件：1）USB转DC输出线*1个；2）手机转接头*5个；3）LED灯*2；4）活动灯头*1个；5）太阳能板和系统连接线：5米*1条；6）活动DC头*2个；7）3米长线+灯头*1条；8）笔记本转接头一套；9）说明书一张。
五、产品适用范围：笔记本电脑充电，12V直流灯、12V3A以内的用电设备、数码摄像机、数码照相机、手机、MP3、MP4、GPS导航、PDA、便携式DVD、对讲机、收音机、录音机等（NEW可以给笔记本电脑充电）六、系统图片：2、蓄电池指示灯（绿灯代表蓄电池有电、红灯代表蓄电池没电）3、12V负载指示灯（红灯亮时，DC12V输出）4、19V指示灯（红灯亮时，DC12V输出）5、5V指示灯（红灯亮时，USB接口DC5V输出）6、U SB输出接口7、D C 12V输出开关8、U SB 5V输出开关9、D C 19V输出DC口（可为笔记本电脑充电）10、DC 12V输出DC口（12V灯及12V负载使用）11、DC 19V输出开关12、太阳能电池板充电输入接口13、总开关（充电或者用电必须把总开关打开）14、系统箱体15、太阳能电池板。
便携式太阳能充电宝8000mAh说明书
INSTRUCTION MANUAL PORTABLE SOLAR POWER BANK 8.000MAHCOMPONENTS•Solar power bank•USB cable•Buckle•Compass•User manualTECHNICAL SPECIFICATIONS•Capacity: 8.000mAh•Case material: ABS + PC + Silicone•Battery type: A grade Li-polymer battery •Net weight: 280g•Product size: 139 x 75 x 20mm•Input: 5V/1.0A•Output: 5V/1A, 5V/2.1A•Color: orange, blue, green, red, black, yellow•Solar panel: polycrystalline• 1.2m drop testing passed•Waterproof and dustproof IPX5 certified. HOW TO USE1.Light2.Power button3.Outlet 14.Outlet 25.Inlet6.Solar panelO FIRST TIME USEWe recommend you charge the battery fully beforeusing it for the first time. The capacity should befully optimized after 2–3 times of fully charging anddischarging the unit.O CHARGINGYou can charge the power bank with the includedUSB connector, or the one that comes with yourphone or other rechargeable device. If you do nothave a USB adapter, you can plug your connectorinto your compute r’s USB port. The solar panel isfor emergencies, since it is slower to charge thatway. The stronger the sun, the quicker is its charge.O POWER CONTROL SWITCHFirmly press the power button one time. This willturn on blue light indicators that show you how fullis the power bank.• 1 blue light = the charger needs to berecharged.• 2 blue lights = <25% remaining charge• 3 blue lights = 25–50%• 4 blue lights = 50–75%•5 blue lights = the device is at 75–100% charge(Green lights mean t’s being sun-charged))Firmly press the power button for 2 seconds, andthe LED flashlight will go on. Press once again tocycle through modes (bright light, emergency SOSsignal).Firmly press the power button for 2 seconds again to turn the flashlight off.COMPATIBLE DEVICESMost digital products with 5V 1A or 2A power rating can be charged easily.•wireless earphones•tablets•digital cameras•any USB chargeable phones•mp3/mp4 players•any USB device with the same power rating of 5V 1A or 2A. TROUBLESHOOTINGProblem: my USB chargeable device does not seem to be charging when connected to the solar charger.Solution: please try to use the same connector you would normally charge your USB device with. If that works, it is likely that due to wear and tear of the connector that comes with the solar charger, which is not lining up with your USB device’s port.Problem:the flashlight won’t turn on or off. / The flashlight is stuck on either bright or SOS mode.Solution: To turn the flashlight on you will need to firmly hold the power button for 2 seconds. Once the flashlight is on, simply click the power buttonagain to cycle through different modes. Hold thepower button for 2 seconds again to turn off thelight.Problem: the solar charger does not indicate thegreen light when in the sun or seems to be chargingslowly.Solution: please make sure the charger is underdirect, strong sunlight. Depending on the strengthof the sunlight, green lights will indicate the chargepower.Note: due to the conveniently compact size of thecharger, the size of the solar panel will enable onlya very slow charge time. It only serves as anemergency feature that will allow you to getenough power for that critical phone call.SAFETY PRECAUTIONS1.Keep the battery away from heat sources (likea fire or heater).2.Do not throw the battery into fire or heat thebattery.3.Do not hammer or trample the battery.4.Do not try disassembling the battery in anyway.5.This product is waterproof, but with limits. Itshould not be used under water. It is a safetyfeature that protects internal electronics,when briefly submerged.6.Please note that the charger clip is meant forcarrying on a key chain and is not intended as abelt clip.7.The battery is made from a high grade lithiumpolymer.8.Keep out of reach of small children.e this product in a well-ventilated area; it isnot recommended to place on your car’sdashboard when the windows are up as thiscould damage the product.10.Do not tamper with the internal componentsas this will void the 1-year warranty of yourdevice and could furthermore result in othermalfunctions of the unit.WARRANTYThe warranty is valid for 12 months, and you cansend your claim to the seller (us), through thecontact details listed in the bottom right corner. Tosubmit a warranty claim, send the order numberand date of your purchase.WEEE disposal and recycling symbol. The WEEE symbol is attached to the product in compliance with the EU directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). It is intended to deter the improper disposal of this product and topromote reuse and recycling.。
太阳能充电宝品规格书
太阳能充电宝产品规格书型号：JN950编制：_________审核：_________核准：_________客户承认：_________目录1．产品概述 (2)2．产品规格 (2)3．电性参数 (2)4．带载能力及效率图表示意 (4)5．功能描述 (5)6．工作原理 (5)7．安全系统要求 (6)8．环境适应及安全保护 (6)9．包装要求 (7)1.产品概述1.1 本产品是专为移动数码产品设计的智能备用电源。
1.2 本产品适用智能手机、平板电脑、便携影音播放设备、掌上游戏机设备等5V直流输入设备，直流12V 的3W-5W 灯泡照明。
1.3 本产品输入部分采用了锂电池专用充电管理IC ，锂电池使用专用保护电路，实现精确控制电压过充、电压过放、电流过载及短路保护，安全性能高；输出采用高效率DC-DC 升压转换电路；同时采用MCU 微电脑控制管理, 实现负载插入自动开机、充满自停、过流保护、电量检测与显示、超低功耗待机等功能。
采用绿光指示，外观圆润细腻，手感舒适。
2. 产品主要规格型 号 JN950输入(V/A/W) 12.6V/1.5A/18.9W 输入端口 DC¢6.5充电端口 总输出(V/A/W) 5V/2.4A/12W 输出端口 单个USB 输出端口 产品容量(mAh) 6000mAh能量(Wh) 66.6Wh （3并3串） 按 键 按键开启输出 显 示 4绿色电量显示LED 尺寸（mm ） 205*200*68mm重量（g ）900g实物图：（需要标注长宽高尺寸，LED 顺序说明）电性参数3.1 保护参数项目详细内容最小值 典型值最大值单位备注拔动按键LED 电量指示灯灯USB 输出口DC ¢6.5mm 或太阳能板输入口DC ¢3.8mm 输出口保护参数配置过充单节过充保护 4.25 4.275 4.30 V单节过充保护延迟时间150 340 500 ms VDD=3.6Vto4.4v 单节过充保护恢复 4.15 4.20 4.25 V过放单节过放保护 2.9 3.05 3.1 V单节过放保护延迟时间80 200 300 ms单节过放保护恢复 3.0 3.10 3.15 V过流放电硬件过流保护4510 A放电软件过流保护 2.2 2.6 2.8 A放电过流保护延迟时间9 12 15 ms短路短路保护有短路恢复方式按键激活短路保护延迟时间200 300 400 μs3.2 输出参数项目详细内容最小值典型值最大值单位备注输出参数配置工作参数持续放电电流 2.0 2.1 2.4 A OUT1 电池3.3V -4.2V放电截止电流10 60 80 mA空载电压4.95.1 5.2 V OUT1 电池3.3V -4.2V带载电压4.755.15 5.2 V OUT1 CC1A电池3.3V-4.2VD+/D-电压短路接法OUT1 空载输出纹波85 100 mV OUT1 CC1.0A 电池3.78V升压转化效率90 92 ％OUT1 CC 1A 电池3.78V空载关机延时时间25 30 35 S整机静态电流50 100 uA3.3 充电管理项目详细内容最小值典型值最大值单位备注充电参数配置充电电压12.6 13.0 13.5 V 涓流充电阈值8.7 9.0 9.3 V 恒定充电电流 1.0 1.2 1.5 A 恒定充电电压12.48 12.66 12.75 V充电截止电流150 180 mA3. 效率及动态负载电压示意图效率图70.00%75.00%80.00%85.00%90.00%95.00%100.00%0.51 1.52 2.33.13.33.84OUT1 效率图动态负载电压图4.34.454.64.754.95.055.20.51 1.52 2.33.13.33.84OUT1电压4. 产品基本操作及功能说明5.1 产品基本操作：a) 手动开机：太阳能充电宝不接外设时，拔动开关“ON ”启动输出、绿灯电量指示灯一直显示当前电量。
太阳能充电宝设计方案
太阳能充电宝设计方案太阳能充电宝是一种新型的充电设备，可以使用太阳能将阳光转化成电能，以供手机、平板电脑等电子设备充电。
以下是一份太阳能充电宝的设计方案。
一、产品特点：1. 太阳能充电：充电宝具备太阳能电池板，可以通过吸纳阳光将其转化成电能，实现绿色能源充电。
2. 大容量电池：内置高容量锂电池，可提供长时间的充电。
例如：10000mAh容量。
3. 多功能输出接口：充电宝需提供USB接口和Wireless充电功能，可以同时给手机、平板电脑等设备充电。
4. 防水防尘设计：充电宝需要具备防水防尘的设计，以适应户外使用环境。
5. 显示屏：充电宝需要配备显示屏，以显示充电电量和剩余电量。
二、产品外观设计：1. 外壳材质：充电宝外壳采用高强度塑料材质，耐用且轻便，方便携带。
2. 外观颜色：可以提供多种颜色选择，以满足不同消费者的喜好。
3. 大小设计：充电宝设计合理的大小，便于携带和使用。
三、电池和充电板设计：1. 采用高效太阳能电池板：选择高效转化阳光能源的太阳能电池板，以提高充电效率。
2. 充电芯片设计：使用高效的充电芯片，保证电能的转化和充电速度。
3. 充电保护措施：为了避免过度充电和过度放电，充电宝应具备过充和过放电保护功能。
四、性能和使用体验：1. 充电效率：太阳能充电宝应该具备高效率的充电功能，以缩短充电时间。
例如：利用太阳能充电4-6小时即可充满电池。
2. 轻便携带：设计紧凑的外观和轻便的重量，方便用户随身携带，适用于户外旅行和露营等活动。
3. 多功能使用：充电宝不仅可以通过太阳能充电，还有USB 接口和无线充电功能，以适应不同的设备充电需求。
4. 安全性：在设计中应考虑到与充电宝相关的产品安全性，如防止电池过热、火灾等情况的发生。
总结：以上是一份关于太阳能充电宝的初步设计方案。
在设计中需要考虑产品的功能性、耐用性、便携性和安全性等因素，以提供满足用户需求的产品。
另外，随着技术的发展和用户需求的变化，设计方案可能会有所调整和改进。
680wp太阳能组件规格书
680wp太阳能组件规格书
太阳能组件规格书是太阳能产品的重要文件之一，它包含了太阳能组件的详细规格参数和技术要求，对于太阳能组件的选购和使用具有重要的指导作用。
下面是一个典型的太阳能组件规格书的内容参考：
1. 产品型号：680wp太阳能组件
2. 额定功率：680Wp
3. 最大功率电压（Vmp）：39.6V
4. 最大功率电流（Imp）：17.2A
5. 开路电压（Voc）：48.8V
6. 短路电流（Isc）：18.5A
7. 尺寸：2000mm x 1000mm x 35mm
8. 重量：25kg
9. 额定工作温度：-40℃~85℃
10. 额定输出电压：DC1000V
11. 防护等级：IP67
12. 透光率：>93%
13. 电池片材质：单晶硅
14. 边框材质：铝合金
15. 后板材质：高透明钢化玻璃
16. 连接器类型：MC4
17. 额定寿命：25年
18. 产品认证：CE、TUV、IEC等
19. 其他特性：抗风压、防腐蚀、抗结霜等
根据上述规格书内容，我们可以了解到680wp太阳能组件的技术参数和性能特点，可以根据这些信息来选择合适的太阳能组件进行安装和使用。
在选购太阳能组件时，除了关注额定功率和电压外，还要考虑其工作温度范围、防护等级、材质和认证等因素，以确保产品的质量和稳定性。
希望以上内容能够满足您对680wp太阳能组件规格书的需求，如需更详细的信息，可以联系太阳能组件生产厂家或供应商进一步了解。
200W350W530W72V36V太阳能板折叠包快充MPPT
产品讲解本产品采用单晶太阳能电池片生产，大于70000光谱下扔具备优质的产品性能，精湛的产品生产工艺，成熟的封装工艺，产品外观美观独特，方便携带.产品质保：两年内对产品材料和工艺的保证.产品特征本产品采用采用单晶太阳能电池片，耐高温、易清洗的表面光伏材料PET或Etfe，以及层压高粘接性、耐腐蚀性、抗老化EVA，加上高反射功能高分子材料TPT生产而成。
本产品转换效率高，耐腐蚀性强，寿命长，易于安装的特性.核心价值观：轻载体积小类型、功率大效率高、独特折叠方式独特富耀颜色撘配.我司所有产品可以根据客户要求进行定制.产品应用本产品广泛应用于通信站、电子产品、移动设备、电源、UPS、石油管道、海洋侦查、气象监测、高速公路、军事、野营、游艇、轮船、汽车、新能源产品、户外运动领域等.品牌：汉匠名称：260w高效太阳能折叠充电包适合搭配三元电池或磷酸铁锂. 固态电池13串电池组充电规格电压可选：36v72v44V硅片类型：A级高效太阳能电池片转换效率:23%以上发电面积：335*510mm表层材料：磨砂PET/Etfe包包材料：900D或1200D布料颜色：黑色+黄色（可定制其他颜色）展开尺寸：1470*1100mm折叠尺寸：336*537*75mm产品净重：9 KGS输出插头：dc7909或依客户要求定制参数产品型号：w200，W260 W350 W530 单片产品功率：35W折数：4折2排连接方式：1串2并总功率：260W工作电压：60V工作电流：4.3A开路电压：96V短路电流：8.7A系统电压（IEC / UL）：1000V工作温度：-40℃至85℃功率温度系数：- 0.38％/ K电压温度系数：-132.5 mV / K电流温度系（-1.8mV /oC）出厂测试标准：辐视量1000W／M2，工作温度25℃，大气质量：1.5g（太阳能组件测试仪、El）400-7162528技术愿景汉匠致力将最高水准的专业知识和工作经验凝聚成符合全球市场需要的一个个视觉体验，为海内外市场提供高品质的服务，给世界带来惊叹和喜悦。
POWERYOU太阳能折叠包电池板规格书-
品系列Array产包装打样10-15天深圳交货：15个工作日美国奥地利日本交货：50工作日南美：25工作日专注于太阳能电池板供应链解决方案创新企业。
企业拥有整套市场核心价值竞争实力如：MPPT跟踪系统制造、ETFE层压太阳能板制造工艺、缝纫电压制造等光伏设备的研发、生产、销售及服务价值。
基于12余年太阳能制造工艺和折叠包成型电压技术积淀，依托领先的系统集成设计能力，我们将智能混合能源技术与储能技术、云计算技术紧密结合，致力于为客户、员工、合作伙伴和投资者提供卓越的光伏产品和整体解决方案服务。
未来，我们将实现从设备与设备的智能交互到设备与人的智能交互，并通过行业布局，依托体系化市场战略和全面的技术支撑网络，推动全球能源转型，发展可持续的未来能源。
为人类创造绿色能源。
企业使命汇聚才能、创造精准100年好电源，领先一步，为“绿色能源”事业做出应有的贡献企业价值观以人为本，追求卓越。
持续为社会，为企业，为每一位员工创造更大价值企业宗旨突出产品的技术专业性、精湛的工艺性，追求产品高技术、高品质、高效率、高性价比企业精神开拓、创新、务实、诚信企业理念以诚相待，真心沟通。
以丰富的专业经验和专业技能为客户提供优质、满意的服务技术支持为了实现上述目标，我们建立了完善，快速反应的售后服务体系，针对具体客户制定有效的技术服务策略，努力满足客户的售后服务需求。
我们把“服务到位，顾客满意”作为衡量工作的准绳，一切工作围绕客户满意展开，在工作中不断发现不足，及时加以修正和完善。
经营理念我们以客户需求和前沿发展理念为驱动力，使公司始终处于行业领先创新地位，将富有特色的方案与强大的技术相结合，不断增强综合解决能力。
凭借强有力的学术与技术背景，带来创新思维和应用国际视野，与国际潮流同步并基于对汉匠求精的了解，技术愿景致力将最高水准的专业知识和工作经验凝聚成符合全球市场需要的一个个视觉体验，为海内外市场提供高品质的服务，给世界带来惊叹和喜悦。
光储充产品手册
光储充产品手册一、产品概述光储充是一款结合了太阳能发电、储能电池和快速充电技术的新型充电设备。
它旨在利用可再生能源，提供绿色、高效的充电解决方案，同时通过储能技术，保障充电的稳定性和持续性。
二、产品特点1. 绿色能源：光储充设备配有高性能的太阳能电池板，能有效地利用太阳能进行充电，减少对传统电网的依赖，实现绿色能源的可持续利用。
2. 储能技术：内置的高性能储能电池，能有效地储存和释放电力，确保在断电或电力需求高峰期时，仍能提供稳定的电力输出。
3. 快速充电：光储充设备配备了先进的快速充电技术，能在短时间内为电动汽车或其他电子设备提供大量的电力。
4. 多重保护：设备内置了热保护、过载保护和短路保护等功能，能有效地保护设备和电池的安全，延长设备的使用寿命。
5. 易于安装：光储充设备设计简洁，安装方便，无需专业人员也能轻松安装。
三、使用方法1. 连接电源：将光储充设备连接到稳定的电源插座，保证电力供应。
2. 启动充电：打开设备开关，太阳能电池板开始吸收阳光进行充电，同时储能电池也开始充电。
3. 连接负载：将需要充电的电动汽车或其他电子设备连接到光储充设备的充电口。
4. 充电过程：设备会自动识别负载并进行充电，同时显示充电进度和电量信息。
5. 断电保护：当电网断电时，光储充设备会自动切换到储能电池供电，保证设备的持续供电。
四、注意事项1. 请在安全环境下使用本产品，避免潮湿、高温或极寒环境。
2. 请勿在雷电天气下使用本产品。
3. 请勿在设备工作时移动或摇晃设备。
4. 请定期对储能电池进行维护和清洁，保证设备的正常运行。
5. 如遇设备故障，请立即停止使用，并联系专业人员进行维修。
Renogy 100W 太阳能充电箱用户手册说明书
Solar SuitcaseRenogy 100W Solar Suitcase Manual w/o CC ManualImportant Safety InstructionsPlease save these instructions.This manual contains important safety, installation, and operating instructions for the charge controller. The following symbols are used throughout the manual to indicate potentially dangerous conditions or important safety information.WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task.CAUTION: Indicates a critical procedure for safe and proper operation of the controller NOTE: Indicates a procedure or function that is important to the safe and proper operation of the controller.General Safety Information•Read all of the instructions and cautions in the manual before beginning the installation.•It is HIGHLY recommended to install a charge controller in order to charge your batteries.It is dangerous for unregulated panels to be connected to battery banks.Battery Safety•Use only sealed lead-acid, flooded, or gel batteries which must be deep cycle.•Explosive battery gases may be present while charging. Be certain there is enough ventilation to release the gases.•Be careful when working with large lead acid batteries. Wear eye protection and have fresh water available in case there is contact with the battery acid.•Carefully read battery manuals before operation.•Do NOT let the positive (+) and negative (-) terminals of the battery touch each other.•Recycle battery when it is replaced.•Over-charging and excessive gas precipitation may damage the battery plates and activate material shedding on them. Too high of an equalizing charge or too long of one may cause damage. Please carefully review the specific requirements of the battery used in the system.Table of ContentsGeneral Information (4)Identification of Parts (4)Installation (5)Recommended Wiring (7)Frequently Asked Questions (8)Technical Specifications (9)Solar Panel Parameters (9)Dimensions (10)General InformationThe Renogy Solar Suitcases combines 2 highly efficient 50W monocrystalline solar panels. This system is specifically designed for mobile off-grid applications, where space and weight limitations are abundant. The Solar Suitcase models support 12V deep cycle battery varieties such as sealed, lead acid, gel, and flooded. With built-in tilting stands, these panels can be adjusted at different angles to maximize the power output throughout the seasons.Key Features• Monocrystalline• Adjustable corrosion resistant aluminum stand. • Heavy duty handle and latches for longevity • Convenient storage case for easy transportation.• Expandable with other solar suitcases based on space availabilityNOTE: The suitcases require an adapter kit, a charge controller, and a tray cable. These components require a separate purchase.Identification of Parts14352Key Parts1. Junction Boxes2. Tilt Stands3. Latches4. Handle5. MC4 ConnectionsInstallation1. Unlatch and unfold unit2. Unscrew butterfly nut tilt to desired angle and lock butterfly nutTo maximize the output, adjust the angle of the suitcase regularly to track the sun’s movement throughout the seasonSummerθ = Latitude – 15°Fall and Springθ = at latitudeθWinterθ = Latitude + 15°Recommended WiringThe 100W Solar Suitcase is shipped by itself without any additional components. In order to utilize the suitcase efficiently, it is highly recommended that users put their system together with the following components:1. Adapter kit—has an MC4 connection on one end and bare wire on the other end forconnecting to a charge controller.2. Charge controller—regulates the solar panel power to efficiently charge batteries.3. Tray cable—has a bare wire on one end and a battery “O-ring” on the other end for connectingthe charge controller to the battery bank.4. Battery bank—where power from the solar panels will be stored.NOTE: Depending on the user’s preference, different gauge wires, wire lengths, charge controllers, and cables could possibly be used.1. Use tray cable to connect battery bank to charge controller’s battery terminals2. Connect adapter kit to MC4 connections coming from the suitcase’s junction box3. Connect adapter kit to charge controller PV terminalsFrequently Asked QuestionsQ. What type of batteries can be used with this kit?A. Any sealed lead acid, gel, or flooded 12V battery (typically used in caravans, motorhomes, boats etc.) is appropriate for use with this kit. Q. Can this kit charge a 24V battery?A. No, because this kit is designed to charge a 12V battery. Technically, it’s possible to change solar panel connections to enable the kit to work in 24V mode; however, a qualified, knowledgeable individual should only do this.Note: unauthorized modification to 24V will void the warranty.Q. Can the kit charge two or more 12V batteries connected in parallel?A. Yes, it’s possible if the batteries have the same type and capacity and are wired in parallel as a single 12V battery bank.Q. Is there any risk that the solar kit will over charge my battery?A. One of the functions of the solar charge controller is to ensure that your battery is not over charged; therefore there is no risk of overcharge. Q. Can I extend the battery leads?A. Yes, it’s possible – please choose the same size of cable for extension. However, there longer the extension, the greater the line loss. Bigger gauge will be required for longer runs.Q. Do I need to clean the solar panels?A. Yes, it is recommended for better performance. Dust and dirt should first be swept off the panel surface using a soft brush. When the sweeping is complete, use a wet cloth to wipe the panel surface to remove remaining dirt and grime.Q. Can rain damage the solar kit?A. The solar panels are fully waterproof (IP66 class), the controller is not. We recommend protecting the kit from rain, since water into controller may damage the internal circuitry.Technical SpecificationsSolar Panel ParametersDescription 100 W ParametersMaximum Power 100 WOpen Circuit Voltage (Voc) 21.6 VShort Circuit Current (Isc) 6.16 AMaximum Power Voltage (Vmp) 18.0 VMaximum Power Current (Imp) 5.56 ACell Type MonocrystallineOperating Temperature −40°F to +185°FFolded Size 19.9 x 27.2 x 2.8 inNet Weight 27.05 lbs.。
LandStar E EU系列产品说明书：太阳能充电器
1 2LandStar E/EU series——Solar Charge Controller1.Safety Information•Read all of the instructions in the manual before installation.•DO NOT disassemble or attempt to repair the controller.•Install external fuse or breaker as required.•Do disconnect the solar module and fuse/ breakers near to battery beforeinstalling or moving the controller.•Power connections must remain tight to avoid excessive heating from aloose connection.•Only charge batteries that comply with the parameters of controller.•Battery connection may be wired to one battery or a bank of batteries.•Risk of electric shock, the PV and load can produce high voltages when thecontroller is working.2. OverviewThe LandStar E series controller is a PWM charge controller that adopts themost advanced digital technique. It’s an easy operation and cost efficientcontroller featured as:•3-Stage intelligent PWM charging：Bulk, Boost/Equalize, Float•Support 3 charging options: Sealed, Gel, and Flooded•Battery status LED indicator can indicates battery situation•Battery temperature compensation function•With humanized settings, operation will be more comfortable and convenient•The USB will provide power supply that can charge for electronicequipment(LS EU series only)•Battery type and load output can be set via button•Extensive Electronic protection3. Product Features4. WiringStep 2：Connect the system in the order of ❶battery →❷ load→❸PV arrayin accordance with Figure 2-2,”Schematic Wiring Diagram” and disconnect thesystem in the reverse order❸❷❶.NOTE: While wiring the controller do not close the circuit breaker orfuse and make sure that the leads of "+" and "-" poles are connectedcorrectly.NOTE: A fuse which current is 1.25 to 2 times the rated current ofthe controller must be installed on the battery side with a distancefrom the battery not greater than 150 mm.NOTE: If an inverter is to be connected to the system, connect theinverter directly to the battery, not to the load side of the controller.5. LED Indicators1) Charging and load status indicator2) Battery status indicator①Voltage value for 12V system at 25℃, please use 2× in 24V system ;②"○"LED indicator on; "×"LED indicator off.6. Setting Operation1)Load ON/OFF SettingWhen the controller is powered on, press the button to control the load output.2)Battery Type SettingOperation:Step 1: Enter setting mode by pressing button for 5s until the battery statusLEDs are flashing.Step 2: Select the desired mode by pressing button.Step 3: The mode will be saved automatically without any operation for 5S andLED will stop flashing.Figure 1 Product FeatureFigure 2 Connection diagram3 4Below parameters are in 12V system at 25 ºC, please double the values in7. Protection • Battery Over Voltage ProtectionWhen the battery voltage reaches to the set point of Over Voltage Disconnect Voltage(OVD), the controller will stop charging the battery to protect the battery from being over charged to break down. • Battery Over Discharge ProtectionWhen the battery voltage reaches to the set point of Low Voltage Disconnect Voltage(LVD), the controller will stop discharging the battery to protect the battery from being over discharged. • Load Overload ProtectionLoad will be switched off when 1.25 times rated current overload happens. User has to reduce load appliance, then press the button or repower the controller.• Load Short Circuit ProtectionLoad will be switched off when load short circuit (≥3 times rated current) happens. User has to clear short circuit, then press the button or repower the controller.• High Voltage Transients ProtectionThe controller is protected against small high voltage transients. In lightning prone areas, additional external suppression is recommended.nominal value, the controller will automatically turn off loads in 60s, 5s and 1s respectively.10. Disclaimer This warranty does not apply under the following conditions: • Damage from improper use or use in an unsuitable environment.• PV or load current, voltage or power exceeding the rated value of controller. • User disassembly or attempted repair the controller without permission. • The controller is damaged due to natural elements such as lighting. • The controller is damaged during transportation and shipment.Any changes without prior notice! Version number ：V2.09. Technical Specifications。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
电性参数
3.1 保护参数
项目
详细容
最小值 典型值 最大值 单位 备注
保护参 数 配 置
过充
单节过充保护
4.25 4.275 4.30 V
单节过充保护延迟时间 150 340 500 ms VDD=3.6Vto4.4v 单节过充保护恢复 4.15 4.20 4.25 V 过放
单节过放保护
2.9
3.05 3.1 V 单节过放保护延迟时间 80 200 300 ms 单节过放保护恢复 3.0 3.10 3.15 V 过流
放电硬件过流保护
4 5 10 A 放电软件过流保护 2.2 2.6 2.8 A 放电过流保护延迟时间 9
12
15
ms
短路
短路保护
有
短路恢复方式 按键激活
短路保护延迟时间
200
300
400 μs 3.2 输出参数 项目
详细容
最小值 典型值 最大值
单位 备注
输出参数配置
工作参数
持续放电电流
2.0 2.1 2.4 A OUT1 电池
3.3V -
4.2V
放电截止电流 10 60 80 mA
空载电压
4.9
5.1 5.2 V OUT1 电池3.3V -4.2V
拔动按键
LED 电量指示灯灯
USB 输出口
DC ¢6.5mm 或太阳
能板输入口
DC ¢3.8mm 输出口。